DKT-GE-MIB
File:
DKT-GE-MIB.mib (37409 bytes)
Imported modules
Imported symbols
Defined Values
geMIB |
1.3.6.1.4.1.27304.14 |
DKT Gigabit MIB. |
MODULE-IDENTITY |
|
|
|
geATU |
1.3.6.1.4.1.27304.14.1.1 |
Dumps the Address Translation Unit (ATU) Switch table in semi colon format |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..20480) |
|
geUnicastDelete |
1.3.6.1.4.1.27304.14.1.2 |
Removes a unicast MAC address from the Address Translation Unit (ATU) Switch table. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
geMulticastDelete |
1.3.6.1.4.1.27304.14.1.3 |
Removes a multicast IP address from the Address Translation Unit (ATU) Switch table. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
geIGMPSnooping |
1.3.6.1.4.1.27304.14.1.4 |
Starts/stops IGMP snooping, input parameter 0 = stops IGMP snooping, 1 = starts IGMP snooping. Per Default IGMP snooping is enabled, but has to be configured per port |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geVTU |
1.3.6.1.4.1.27304.14.1.5 |
Dumps the VLAN Table Unit (VTU) Switch table in semi colon format |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..9600) |
|
geVLANCreate |
1.3.6.1.4.1.27304.14.1.6 |
Creates a VLAN, input parameters are: VID:WAN:LAN1:LAN2:LAN3:LAN4:CPU:NRL-ENABLE |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
geVLANDelete |
1.3.6.1.4.1.27304.14.1.7 |
Deletes a VLAN, input parameter is VLAN VID: 0 - 4095 |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..4095 |
|
geClearVTU |
1.3.6.1.4.1.27304.14.1.8 |
Clears the VLAN Table Unit (VTU) Switch table, input parameter 1 = clear VTU table |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1 |
|
geDumpPIRLBuckets |
1.3.6.1.4.1.27304.14.1.9 |
Dumps a list of the active buckets. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..10) |
|
geVLANProviderMode |
1.3.6.1.4.1.27304.14.1.10 |
Enable/disable VLAN provider mode, input parameter 0 = disable VLAN provider mode, 1 = enable VLAN provider mode. Per Default VLAN provider mode is disabled. NOTE: Provider VLAN ID should be setup in port default VID for the originating port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
gePorts |
1.3.6.1.4.1.27304.14.2 |
OBJECT IDENTIFIER |
|
|
|
geCPUPort |
1.3.6.1.4.1.27304.14.2.1 |
OBJECT IDENTIFIER |
|
|
|
geCPUPortAutoNegotiation |
1.3.6.1.4.1.27304.14.2.1.1 |
Enables/disables auto negotiation on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..10 |
|
geCPUPortSpeedMode |
1.3.6.1.4.1.27304.14.2.1.2 |
Sets/gets the speed and duplex mode on the port. Input parameters are: AUTO |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..10) |
|
geCPUPortLinkStatus |
1.3.6.1.4.1.27304.14.2.1.3 |
Gets the Link status for the port |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geCPUPortFlowControl |
1.3.6.1.4.1.27304.14.2.1.4 |
Enables/disables flow control on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geCPUPortIEEEQoSPriority |
1.3.6.1.4.1.27304.14.2.1.5 |
Enables prioritized frames based on there IEEE priority tags. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geCPUPortIPQoSPriority |
1.3.6.1.4.1.27304.14.2.1.6 |
Enables prioritized frames based on their IP4/IP6 priority fields. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geCPUPortQoSPortMapRule |
1.3.6.1.4.1.27304.14.2.1.7 |
Forces queue priority for a port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geCPUPortVIDNRLEnable |
1.3.6.1.4.1.27304.14.2.1.8 |
Enables/disables per port the Non rate limit for VLANs with the NRL bit enabled. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geCPUPortDisablePIRL2Bucket |
1.3.6.1.4.1.27304.14.2.1.9 |
Disables per port an already defined Port Ingress Rate Limitation (PIRL) bucket, input parameter bucket 0 - 4. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..4 |
|
geCPUPortEgressRateLimitation |
1.3.6.1.4.1.27304.14.2.1.10 |
Sets the egress limitation rate for the port. Input parameter is value in kbps |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
geCPUPortIngressRateLimitation |
1.3.6.1.4.1.27304.14.2.1.11 |
Sets a Port Input Rate Limit(PIRL) bucket. Input parameters are: bucket:rate:layer:(DROP|FC) |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
geCPUPortDefaultVLAN |
1.3.6.1.4.1.27304.14.2.1.12 |
Sets the default VLAN ID(VID) for the port. Input parameter is 0 - 4095 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
geCPUPortForceDefaultVID |
1.3.6.1.4.1.27304.14.2.1.13 |
Forces the tagging of VID on all frames on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geCPUPortVLANPortMode |
1.3.6.1.4.1.27304.14.2.1.14 |
Sets the 802.1Q mode for the ingress port.
Mode either 0=disable,
1=fallback,
2=check,
3=secure |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..3 |
|
geCPUPortBlockAllUnknown |
1.3.6.1.4.1.27304.14.2.1.15 |
This will make sure that all frames received on the port are blocked, unless they are tagged with the correct VID. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geCPUPortIGMPSnooping |
1.3.6.1.4.1.27304.14.2.1.16 |
Enables/disables IGMP snooping. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geCPUPortAddUnicast |
1.3.6.1.4.1.27304.14.2.1.17 |
Adds the unicast mac address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aa:bb:cc:dd:ee:ff |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
geCPUPortAddMulticast |
1.3.6.1.4.1.27304.14.2.1.18 |
Adds the IP multicast address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aaa.bbb.ccc.ddd |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
geCPUPortMtu |
1.3.6.1.4.1.27304.14.2.1.19 |
The MTU size of the port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..2 |
|
geWANPort |
1.3.6.1.4.1.27304.14.2.2 |
OBJECT IDENTIFIER |
|
|
|
geWANPortAutoNegotiation |
1.3.6.1.4.1.27304.14.2.2.1 |
Enables/disables auto negotiation on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..10 |
|
geWANPortSpeedMode |
1.3.6.1.4.1.27304.14.2.2.2 |
Sets/gets the speed and duplex mode on the port. Valid values are (1000FD|1000HD|100FD|100HD|10FD|10HD|AUTO|FD|HD) |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..10) |
|
geWANPortLinkStatus |
1.3.6.1.4.1.27304.14.2.2.3 |
Gets the Link status for the port |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geWANPortFlowControl |
1.3.6.1.4.1.27304.14.2.2.4 |
Enables/disables flow control on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geWANPortIEEEQoSPriority |
1.3.6.1.4.1.27304.14.2.2.5 |
Enables prioritized frames based on there IEEE priority tags. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geWANPortIPQoSPriority |
1.3.6.1.4.1.27304.14.2.2.6 |
Enables prioritized frames based on their IP4/IP6 priority fields. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geWANPortQoSPortMapRule |
1.3.6.1.4.1.27304.14.2.2.7 |
Forces queue priority for a port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geWANPortVIDNRLEnable |
1.3.6.1.4.1.27304.14.2.2.8 |
Enables/disables per port the Non rate limit for VLANs with the NRL bit enabled. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geWANPortDisablePIRL2Bucket |
1.3.6.1.4.1.27304.14.2.2.9 |
Disables per port an already defined Port Ingress Rate Limitation (PIRL) bucket, input parameter bucket 0 - 4. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..4 |
|
geWANPortEgressRateLimitation |
1.3.6.1.4.1.27304.14.2.2.10 |
Sets the egress limitation rate for the port. Input parameter is value in kbps |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
geWANPortIngressRateLimitation |
1.3.6.1.4.1.27304.14.2.2.11 |
Sets a Port Input Rate Limit(PIRL) bucket. Input parameters are: bucket:rate:layer:(DROP|FC) |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
geWANPortDefaultVLAN |
1.3.6.1.4.1.27304.14.2.2.12 |
Sets the default VLAN ID(VID) for the port. Input parameter is 0 - 4095 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
geWANPortForceDefaultVID |
1.3.6.1.4.1.27304.14.2.2.13 |
Forces the tagging of VID on all frames on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geWANPortVLANPortMode |
1.3.6.1.4.1.27304.14.2.2.14 |
Sets the 802.1Q mode for the ingress port.
Mode either 0=disable,
1=fallback,
2=check,
3=secure |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..3 |
|
geWANPortBlockAllUnknown |
1.3.6.1.4.1.27304.14.2.2.15 |
This will make sure that all frames received on the port are blocked, unless they are tagged with the correct VID. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geWANPortIGMPSnooping |
1.3.6.1.4.1.27304.14.2.2.16 |
Enables/disables IGMP snooping. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geWANPortAddUnicast |
1.3.6.1.4.1.27304.14.2.2.17 |
Adds the unicast mac address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aa:bb:cc:dd:ee:ff |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
geWANPortAddMulticast |
1.3.6.1.4.1.27304.14.2.2.18 |
Adds the IP multicast address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aaa.bbb.ccc.ddd |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
geWANPortMtu |
1.3.6.1.4.1.27304.14.2.2.19 |
The MTU size of the port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..2 |
|
geWANPortArpMirroring |
1.3.6.1.4.1.27304.14.2.2.20 |
Mirror ARP packets seen on the port to the CPU port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN1Port |
1.3.6.1.4.1.27304.14.2.3 |
OBJECT IDENTIFIER |
|
|
|
geLAN1PortAutoNegotiation |
1.3.6.1.4.1.27304.14.2.3.1 |
Enables/disables auto negotiation on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..10 |
|
geLAN1PortSpeedMode |
1.3.6.1.4.1.27304.14.2.3.2 |
Sets/gets the speed and duplex mode on the port. Valid values are (1000FD|1000HD|100FD|100HD|10FD|10HD|AUTO|FD|HD) |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..10) |
|
geLAN1PortLinkStatus |
1.3.6.1.4.1.27304.14.2.3.3 |
Gets the Link status for the port |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN1PortFlowControl |
1.3.6.1.4.1.27304.14.2.3.4 |
Enables/disables flow control on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN1PortIEEEQoSPriority |
1.3.6.1.4.1.27304.14.2.3.5 |
Enables prioritized frames based on there IEEE priority tags. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN1PortIPQoSPriority |
1.3.6.1.4.1.27304.14.2.3.6 |
Enables prioritized frames based on their IP4/IP6 priority fields. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN1PortQoSPortMapRule |
1.3.6.1.4.1.27304.14.2.3.7 |
Forces queue priority for a port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN1PortVIDNRLEnable |
1.3.6.1.4.1.27304.14.2.3.8 |
Enables/disables per port the Non rate limit for VLANs with the NRL bit enabled. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN1PortDisablePIRL2Bucket |
1.3.6.1.4.1.27304.14.2.3.9 |
Disables per port an already defined Port Ingress Rate Limitation (PIRL) bucket, input parameter bucket 0 - 4. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..4 |
|
geLAN1PortIngressRateLimitation |
1.3.6.1.4.1.27304.14.2.3.11 |
Sets a Port Input Rate Limit(PIRL) bucket. Input parameters are: bucket:rate:layer:(DROP|FC) |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
geLAN1PortDefaultVLAN |
1.3.6.1.4.1.27304.14.2.3.12 |
Sets the default VLAN ID(VID) for the port. Input parameter is 0 - 4095 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
geLAN1PortForceDefaultVID |
1.3.6.1.4.1.27304.14.2.3.13 |
Forces the tagging of VID on all frames on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN1PortVLANPortMode |
1.3.6.1.4.1.27304.14.2.3.14 |
Sets the 802.1Q mode for the ingress port.
Mode either 0=disable,
1=fallback,
2=check,
3=secure |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..3 |
|
geLAN1PortBlockAllUnknown |
1.3.6.1.4.1.27304.14.2.3.15 |
This will make sure that all frames received on the port are blocked, unless they are tagged with the correct VID. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN1PortIGMPSnooping |
1.3.6.1.4.1.27304.14.2.3.16 |
Enables/disables IGMP snooping. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN1PortAddUnicast |
1.3.6.1.4.1.27304.14.2.3.17 |
Adds the unicast mac address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aa:bb:cc:dd:ee:ff |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
geLAN1PortAddMulticast |
1.3.6.1.4.1.27304.14.2.3.18 |
Adds the IP multicast address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aaa.bbb.ccc.ddd |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
geLAN1PortMtu |
1.3.6.1.4.1.27304.14.2.3.19 |
The MTU size of the port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..2 |
|
geLAN1PortArpMirroring |
1.3.6.1.4.1.27304.14.2.3.20 |
Mirror ARP packets seen on the port to the CPU port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN2Port |
1.3.6.1.4.1.27304.14.2.4 |
OBJECT IDENTIFIER |
|
|
|
geLAN2PortAutoNegotiation |
1.3.6.1.4.1.27304.14.2.4.1 |
Enables/disables auto negotiation on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..10 |
|
geLAN2PortSpeedMode |
1.3.6.1.4.1.27304.14.2.4.2 |
Sets/gets the speed and duplex mode on the port. Valid values are (1000FD|1000HD|100FD|100HD|10FD|10HD|AUTO|FD|HD) |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..10) |
|
geLAN2PortLinkStatus |
1.3.6.1.4.1.27304.14.2.4.3 |
Gets the Link status for the port |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN2PortFlowControl |
1.3.6.1.4.1.27304.14.2.4.4 |
Enables/disables flow control on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN2PortIEEEQoSPriority |
1.3.6.1.4.1.27304.14.2.4.5 |
Enables prioritized frames based on there IEEE priority tags. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN2PortIPQoSPriority |
1.3.6.1.4.1.27304.14.2.4.6 |
Enables prioritized frames based on their IP4/IP6 priority fields. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN2PortQoSPortMapRule |
1.3.6.1.4.1.27304.14.2.4.7 |
Forces queue priority for a port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN2PortVIDNRLEnable |
1.3.6.1.4.1.27304.14.2.4.8 |
Enables/disables per port the Non rate limit for VLANs with the NRL bit enabled. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN2PortDisablePIRL2Bucket |
1.3.6.1.4.1.27304.14.2.4.9 |
Disables per port an already defined Port Ingress Rate Limitation (PIRL) bucket, input parameter bucket 0 - 4. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..4 |
|
geLAN2PortIngressRateLimitation |
1.3.6.1.4.1.27304.14.2.4.11 |
Sets a Port Input Rate Limit(PIRL) bucket. Input parameters are: bucket:rate:layer:(DROP|FC) |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
geLAN2PortDefaultVLAN |
1.3.6.1.4.1.27304.14.2.4.12 |
Sets the default VLAN ID(VID) for the port. Input parameter is 0 - 4095 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
geLAN2PortForceDefaultVID |
1.3.6.1.4.1.27304.14.2.4.13 |
Forces the tagging of VID on all frames on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN2PortVLANPortMode |
1.3.6.1.4.1.27304.14.2.4.14 |
Sets the 802.1Q mode for the ingress port.
Mode either 0=disable,
1=fallback,
2=check,
3=secure |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..3 |
|
geLAN2PortBlockAllUnknown |
1.3.6.1.4.1.27304.14.2.4.15 |
This will make sure that all frames received on the port are blocked, unless they are tagged with the correct VID. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN2PortIGMPSnooping |
1.3.6.1.4.1.27304.14.2.4.16 |
Enables/disables IGMP snooping. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN2PortAddUnicast |
1.3.6.1.4.1.27304.14.2.4.17 |
Adds the unicast mac address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aa:bb:cc:dd:ee:ff |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
geLAN2PortAddMulticast |
1.3.6.1.4.1.27304.14.2.4.18 |
Adds the IP multicast address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aaa.bbb.ccc.ddd |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
geLAN2PortMtu |
1.3.6.1.4.1.27304.14.2.4.19 |
The MTU size of the port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..2 |
|
geLAN2PortArpMirroring |
1.3.6.1.4.1.27304.14.2.4.20 |
Mirror ARP packets seen on the port to the CPU port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN3Port |
1.3.6.1.4.1.27304.14.2.5 |
OBJECT IDENTIFIER |
|
|
|
geLAN3PortAutoNegotiation |
1.3.6.1.4.1.27304.14.2.5.1 |
Enables/disables auto negotiation on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..10 |
|
geLAN3PortSpeedMode |
1.3.6.1.4.1.27304.14.2.5.2 |
Sets/gets the speed and duplex mode on the port. Valid values are (1000FD|1000HD|100FD|100HD|10FD|10HD|AUTO|FD|HD) |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..10) |
|
geLAN3PortLinkStatus |
1.3.6.1.4.1.27304.14.2.5.3 |
Gets the Link status for the port |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN3PortFlowControl |
1.3.6.1.4.1.27304.14.2.5.4 |
Enables/disables flow control on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN3PortIEEEQoSPriority |
1.3.6.1.4.1.27304.14.2.5.5 |
Enables prioritized frames based on there IEEE priority tags. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN3PortIPQoSPriority |
1.3.6.1.4.1.27304.14.2.5.6 |
Enables prioritized frames based on their IP4/IP6 priority fields. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN3PortQoSPortMapRule |
1.3.6.1.4.1.27304.14.2.5.7 |
Forces queue priority for a port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN3PortVIDNRLEnable |
1.3.6.1.4.1.27304.14.2.5.8 |
Enables/disables per port the Non rate limit for VLANs with the NRL bit enabled. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN3PortDisablePIRL2Bucket |
1.3.6.1.4.1.27304.14.2.5.9 |
Disables per port an already defined Port Ingress Rate Limitation (PIRL) bucket, input parameter bucket 0 - 4. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..4 |
|
geLAN3PortIngressRateLimitation |
1.3.6.1.4.1.27304.14.2.5.11 |
Sets a Port Input Rate Limit(PIRL) bucket. Input parameters are: bucket:rate:layer:(DROP|FC) |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
geLAN3PortDefaultVLAN |
1.3.6.1.4.1.27304.14.2.5.12 |
Sets the default VLAN ID(VID) for the port. Input parameter is 0 - 4095 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
geLAN3PortForceDefaultVID |
1.3.6.1.4.1.27304.14.2.5.13 |
Forces the tagging of VID on all frames on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN3PortVLANPortMode |
1.3.6.1.4.1.27304.14.2.5.14 |
Sets the 802.1Q mode for the ingress port.
Mode either 0=disable,
1=fallback,
2=check,
3=secure |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..3 |
|
geLAN3PortBlockAllUnknown |
1.3.6.1.4.1.27304.14.2.5.15 |
This will make sure that all frames received on the port are blocked, unless they are tagged with the correct VID. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN3PortIGMPSnooping |
1.3.6.1.4.1.27304.14.2.5.16 |
Enables/disables IGMP snooping. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN3PortAddUnicast |
1.3.6.1.4.1.27304.14.2.5.17 |
Adds the unicast mac address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aa:bb:cc:dd:ee:ff |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
geLAN3PortAddMulticast |
1.3.6.1.4.1.27304.14.2.5.18 |
Adds the IP multicast address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aaa.bbb.ccc.ddd |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
geLAN3PortMtu |
1.3.6.1.4.1.27304.14.2.5.19 |
The MTU size of the port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..2 |
|
geLAN3PortArpMirroring |
1.3.6.1.4.1.27304.14.2.5.20 |
Mirror ARP packets seen on the port to the CPU port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN4Port |
1.3.6.1.4.1.27304.14.2.6 |
OBJECT IDENTIFIER |
|
|
|
geLAN4PortAutoNegotiation |
1.3.6.1.4.1.27304.14.2.6.1 |
Enables/disables auto negotiation on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..10 |
|
geLAN4PortSpeedMode |
1.3.6.1.4.1.27304.14.2.6.2 |
Sets/gets the speed and duplex mode on the port. Valid values are (1000FD|1000HD|100FD|100HD|10FD|10HD|AUTO|FD|HD) |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..10) |
|
geLAN4PortLinkStatus |
1.3.6.1.4.1.27304.14.2.6.3 |
Gets the Link status for the port |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN4PortFlowControl |
1.3.6.1.4.1.27304.14.2.6.4 |
Enables/disables flow control on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN4PortIEEEQoSPriority |
1.3.6.1.4.1.27304.14.2.6.5 |
Enables prioritized frames based on there IEEE priority tags. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN4PortIPQoSPriority |
1.3.6.1.4.1.27304.14.2.6.6 |
Enables prioritized frames based on their IP4/IP6 priority fields. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN4PortQoSPortMapRule |
1.3.6.1.4.1.27304.14.2.6.7 |
Forces queue priority for a port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN4PortVIDNRLEnable |
1.3.6.1.4.1.27304.14.2.6.8 |
Enables/disables per port the Non rate limit for VLANs with the NRL bit enabled. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN4PortDisablePIRL2Bucket |
1.3.6.1.4.1.27304.14.2.6.9 |
Disables per port an already defined Port Ingress Rate Limitation (PIRL) bucket, input parameter bucket 0 - 4. |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..4 |
|
geLAN4PortIngressRateLimitation |
1.3.6.1.4.1.27304.14.2.6.11 |
Sets a Port Input Rate Limit(PIRL) bucket. Input parameters are: bucket:rate:layer:(DROP|FC) |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
geLAN4PortDefaultVLAN |
1.3.6.1.4.1.27304.14.2.6.12 |
Sets the default VLAN ID(VID) for the port. Input parameter is 0 - 4095 |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
geLAN4PortForceDefaultVID |
1.3.6.1.4.1.27304.14.2.6.13 |
Forces the tagging of VID on all frames on the port. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN4PortVLANPortMode |
1.3.6.1.4.1.27304.14.2.6.14 |
Sets the 802.1Q mode for the ingress port.
Mode either 0=disable,
1=fallback,
2=check,
3=secure |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..3 |
|
geLAN4PortBlockAllUnknown |
1.3.6.1.4.1.27304.14.2.6.15 |
This will make sure that all frames received on the port are blocked, unless they are tagged with the correct VID. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN4PortIGMPSnooping |
1.3.6.1.4.1.27304.14.2.6.16 |
Enables/disables IGMP snooping. Set to 1 for enable and 0 for disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geLAN4PortAddUnicast |
1.3.6.1.4.1.27304.14.2.6.17 |
Adds the unicast mac address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aa:bb:cc:dd:ee:ff |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..100) |
|
geLAN4PortAddMulticast |
1.3.6.1.4.1.27304.14.2.6.18 |
Adds the IP multicast address statically to the Address Translation Unit (ATU) Switch table. Input parameter is: aaa.bbb.ccc.ddd |
Status: current |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
geLAN4PortMtu |
1.3.6.1.4.1.27304.14.2.6.19 |
The MTU size of the port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..2 |
|
geLAN4PortArpMirroring |
1.3.6.1.4.1.27304.14.2.6.20 |
Mirror ARP packets seen on the port to the CPU port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
geModuleGroup |
1.3.6.1.4.1.27304.14.4 |
The objects are related to the DKTCOMEGA Gigabit module, MIB rev 02_00. |
Status: current |
Access: read-write |
OBJECT-GROUP |
|
|
|