E5-111-MIB

File: E5-111-MIB.mib (289601 bytes)

Imported modules

RFC1155-SMI SNMPv2-SMI RFC1213-MIB
SNMPv2-TC Q-BRIDGE-MIB P-BRIDGE-MIB
BRIDGE-MIB

Imported symbols

enterprises OBJECT-TYPE Counter32
Gauge32 Unsigned32 Counter64
IpAddress TimeTicks NOTIFICATION-TYPE
DisplayString PhysAddress ifIndex
RowStatus MacAddress TEXTUAL-CONVENTION
VlanIndex PortList dot1qVlanIndex
dot1dTrafficClass Timeout BridgeId
dot1dBasePort

Defined Types

AlarmConfEntry  
SEQUENCE    
  alarmConfId INTEGER
  alarmConfFacility INTEGER
  alarmConfTarget INTEGER
  alarmConfSeverity INTEGER
  alarmConfClearable INTEGER

AlarmCurrEntry  
SEQUENCE    
  alarmCurrIndex INTEGER
  alarmCurrOccurTime TimeTicks
  alarmCurrTrapOid OBJECT IDENTIFIER
  alarmCurrParam1 INTEGER
  alarmCurrParam2 INTEGER
  alarmCurrParam3 INTEGER
  alarmCurrParam4 INTEGER
  alarmCurrParam5 INTEGER
  alarmCurrParam6 INTEGER
  alarmCurrParam7 INTEGER
  alarmCurrParam8 INTEGER
  alarmCurrTimeDescr DisplayString
  alarmCurrSeverity INTEGER
  alarmCurrDescr DisplayString

AlarmSeverityPortEntry  
SEQUENCE    
  severityThresh INTEGER

MltRelayEntry  
SEQUENCE    
  mltRelaySet INTEGER

McastBwEntry  
SEQUENCE    
  mcastBwIndex INTEGER
  mcastBwStartIp IpAddress
  mcastBwEndIp IpAddress
  mcastBwBandwidth INTEGER
  mcastBwRowStatus RowStatus

McastBwPortEntry  
SEQUENCE    
  mcastBwPortEnable INTEGER
  mcastBwPortBandwidth INTEGER

IgmpCountPortEntry  
SEQUENCE    
  igmpCountPortEnable INTEGER
  igmpCountPortLimit INTEGER

MvlanEntry  
SEQUENCE    
  mvlanIndex VlanIndex
  mvlanName DisplayString
  mvlanEgressPorts PortList
  mvlanUntaggedPorts PortList
  mvlanRowStatus RowStatus

MvlanTranslateEntry  
SEQUENCE    
  mvlanTranslateIndex INTEGER
  mvlanTranslateStartIp IpAddress
  mvlanTranslateEndIp IpAddress

QryVidConfEntry  
SEQUENCE    
  qryVid INTEGER
  qryVidRowStatus RowStatus

QryVidStatusEntry  
SEQUENCE    
  qryVidType INTEGER

IgmpProfileEntry  
SEQUENCE    
  igmpProfileName DisplayString
  igmpProfileEnable INTEGER
  igmpProfileMaxGroup INTEGER
  igmpProfileRowStatus RowStatus

IgmpFilterEntry  
SEQUENCE    
  igmpFilterIndex INTEGER
  igmpFilterStartIp IpAddress
  igmpFilterEndIp IpAddress

IgmpProfilePortEntry  
SEQUENCE    
  igmpProfilePortProfile OCTET STRING

SubrPortEntry  
SEQUENCE    
  subrPortName DisplayString
  subrPortTel DisplayString

AdslLineConfEntry  
SEQUENCE    
  adslLineConfAdslMode INTEGER
  adslLineConfAnnexL INTEGER
  adslLineConfAnnexM INTEGER
  adslLineConfAnnexI INTEGER
  adslLineConfOptionMask INTEGER
  adslLineConfPowerMgmt INTEGER
  adslLineConfPowerMode INTEGER
  adslLineConfAturMaxTxPower INTEGER
  adslLineConfAtucMaxTxPower INTEGER
  adslLineConfMaxRxPower INTEGER
  adslLineConfAturCarrierMask OCTET STRING
  adslLineConfAtucCarrierMask0 OCTET STRING
  adslLineConfAtucCarrierMask1 OCTET STRING
  adslLineConfAturInp INTEGER
  adslLineConfAtucInp INTEGER
  adslLineConfL0Time INTEGER
  adslLineConfL2Time INTEGER
  adslLineConfL2ATPR INTEGER
  adslLineConfL2ATPRT INTEGER
  adslLineConfMaxL2Rate INTEGER
  adslLineConfMinL2Rate INTEGER
  adslLineConfL0toL2Rate INTEGER
  adslLineConfNitro INTEGER
  adslLineConfUSPhyr INTEGER
  adslLineConfDSPhyr INTEGER

AdslLineStatusEntry  
SEQUENCE    
  adslLineStatusMode INTEGER
  adslLineUpTime INTEGER

PowerMgmtParamEntry  
SEQUENCE    
  powerMgmtL0Time INTEGER
  powerMgmtL2Time INTEGER
  powerMgmtL2Atpr INTEGER
  powerMgmtL2Atprt INTEGER
  powerMgmtL2MinRate INTEGER
  powerMgmtL2MaxRate INTEGER
  powerMgmtL2ThreshRate INTEGER

PowerMgmtPSDEntry  
SEQUENCE    
  powerMgmtAtucMaxPSD INTEGER
  powerMgmtAturMaxPSD INTEGER

PvcEntry  
SEQUENCE    
  pvcVpi INTEGER
  pvcVci INTEGER
  pvcPvid VlanIndex
  pvcPriority INTEGER
  pvcProfileDS DisplayString
  pvcProfileUS DisplayString
  pvcAcName DisplayString
  pvcServiceName DisplayString
  pvcHelloTime INTEGER
  pvcRowStatus RowStatus

PvcStateEntry  
SEQUENCE    
  pvcStateVpi INTEGER
  pvcStateVci INTEGER
  pvcStatePvid VlanIndex
  pvcStatePriority INTEGER
  pvcStateChannelType DisplayString
  pvcStateEncap DisplayString

PvcUsRateLimitEntry  
SEQUENCE    
  pvcUsRateLimitEnable INTEGER
  pvcUsRateLimit INTEGER

PpvcEntry  
SEQUENCE    
  ppvcVpi INTEGER
  ppvcVci INTEGER
  ppvcPvid VlanIndex
  ppvcEncap INTEGER
  ppvcPriority INTEGER
  ppvcRowStatus RowStatus

PpvcMemberEntry  
SEQUENCE    
  ppvcMemberVpi INTEGER
  ppvcMemberVci INTEGER
  ppvcMemberPriority INTEGER
  ppvcMemberProfileDS DisplayString
  ppvcMemberRowStatus RowStatus
  ppvcMemberProfileUS DisplayString

RpvcGatewayEntry  
SEQUENCE    
  rpvcGatewayIp IpAddress
  rpvcGatewayVlanId VlanIndex
  rpvcGatewayRowStatus RowStatus
  rpvcGatewayPriority INTEGER

RpvcEntry  
SEQUENCE    
  rpvcVpi INTEGER
  rpvcVci INTEGER
  rpvcDSProfile DisplayString
  rpvcUSProfile DisplayString
  rpvcIp IpAddress
  rpvcNetmask IpAddress
  rpvcGatewayIpAddress IpAddress
  rpvcRowStatus RowStatus

RpvcRouteDomainEntry  
SEQUENCE    
  rpvcRouteDomainVpi INTEGER
  rpvcRouteDomainVci INTEGER
  rpvcRouteDomainIp IpAddress
  rpvcRouteDomainNetmask IpAddress
  rpvcRouteDomainRowStatus RowStatus

DsBcastDisableEntry  
SEQUENCE    
  dsBcastDisableVlanId INTEGER
  dsBcastDisableRowStatus RowStatus

PaepvcEntry  
SEQUENCE    
  paepvcVpi INTEGER
  paepvcVci INTEGER
  paepvcPvid VlanIndex
  paepvcPriority INTEGER
  paepvcProfileDS DisplayString
  paepvcAcName DisplayString
  paepvcServiceName DisplayString
  paepvcHelloTime INTEGER
  paepvcRowStatus RowStatus
  paepvcProfileUS DisplayString
  paepvcCvid VlanIndex
  paepvcCPriority INTEGER

TlspvcEntry  
SEQUENCE    
  tlspvcVpi INTEGER
  tlspvcVci INTEGER
  tlspvcSvid VlanIndex
  tlspvcSpriority INTEGER
  tlspvcProfileDS DisplayString
  tlspvcRowStatus RowStatus
  tlspvcProfileUS DisplayString

IpbpvcDomainEntry  
SEQUENCE    
  ipbpvcDomainName OCTET STRING
  ipbpvcDomainRowStatus RowStatus

IpbpvcDomainVlanEntry  
SEQUENCE    
  ipbpvcDomainVlanId VlanIndex
  ipbpvcDomainDhcpVlanEnable INTEGER
  ipbpvcDomainVlanRowStatus RowStatus

IpbpvcEdgeRouterEntry  
SEQUENCE    
  ipbpvcEdgeRouterIp IpAddress
  ipbpvcEdgeRouterMask INTEGER
  ipbpvcEdgeRouterVid VlanIndex
  ipbpvcEdgeRouterRowStatus RowStatus

IpbpvcInterfaceEntry  
SEQUENCE    
  ipbpvcInterfaceIp IpAddress
  ipbpvcInterfaceMask INTEGER
  ipbpvcInterfaceVid VlanIndex
  ipbpvcInterfaceIfIndex INTEGER
  ipbpvcInterfaceVpi INTEGER
  ipbpvcInterfaceVci INTEGER
  ipbpvcInterfaceRowStatus RowStatus

IpbpvcRouteEntry  
SEQUENCE    
  ipbpvcRouteIp IpAddress
  ipbpvcRouteMask INTEGER
  ipbpvcRouteNextHop IpAddress
  ipbpvcRouteMetric INTEGER
  ipbpvcRoutePriority INTEGER
  ipbpvcRouteRowStatus RowStatus

IpbpvcEntry  
SEQUENCE    
  ipbpvcVpi INTEGER
  ipbpvcVci INTEGER
  ipbpvcPvid INTEGER
  ipbpvcEncap INTEGER
  ipbpvcPriority INTEGER
  ipbpvcProfile OCTET STRING
  ipbpvcRowStatus RowStatus
  ipbpvcProfileUS OCTET STRING

DtpvcEntry  
SEQUENCE    
  dtpvcVpi INTEGER
  dtpvcVci INTEGER
  dtpvcSvid VlanIndex
  dtpvcSpriority INTEGER
  dtpvcCvid VlanIndex
  dtpvcCpriority INTEGER
  dtpvcDSProfile DisplayString
  dtpvcUSProfile DisplayString
  dtpvcRowStatus RowStatus
  dtpvcSuperChannel INTEGER
  dtpvcAcName DisplayString
  dtpvcServiceName DisplayString
  dtpvcHelloTime INTEGER

DtpvcStateEntry  
SEQUENCE    
  dtpvcStateVpi INTEGER
  dtpvcStateVci INTEGER
  dtpvcStateSvid VlanIndex
  dtpvcStateSPriority INTEGER
  dtpvcStateCvid VlanIndex
  dtpvcStateCPriority INTEGER
  dtpvcStateChannelType DisplayString
  dtpvcStateEncap DisplayString

GbondGroupEntry  
SEQUENCE    
  gbondGroupName OCTET STRING
  gbondGroupPorts OCTET STRING
  gbondGroupUpRate Unsigned32
  gbondGroupDownRate Unsigned32
  gbondGroupRowStatus RowStatus

VoipSipLineConfEntry  
SEQUENCE    
  voipSipLineConfSipProfile OCTET STRING
  voipSipLineConfSipCallSvcProfile OCTET STRING
  voipSipLineConfDspProfile OCTET STRING

VoipPortTelEntry  
SEQUENCE    
  voipPortTel DisplayString

VoipH248LineConfEntry  
SEQUENCE    
  voipH248LineConfMgName OCTET STRING
  voipH248LineConfDspProfile OCTET STRING
  voipH248LineConfVBDProfile OCTET STRING

VoipPortH248TerminationEntry  
SEQUENCE    
  voipPortH248TermName OCTET STRING

VoipPortGainEntry  
SEQUENCE    
  voipPortTXGain INTEGER
  voipPortRXGain INTEGER

SnrMarginEntry  
SEQUENCE    
  snrMgnMode INTEGER
  snrMgnUcTarget INTEGER
  snrMgnUcMax INTEGER
  snrMgnUcMin INTEGER
  snrMgnUcDownshift INTEGER
  snrMgnUcUpshift INTEGER
  snrMgnUrTarget INTEGER
  snrMgnUrMax INTEGER
  snrMgnUrMin INTEGER
  snrMgnUrDownshift INTEGER
  snrMgnUrUpshift INTEGER

DslRateEntry  
SEQUENCE    
  dslRateMode INTEGER
  dslRateLatencyMode INTEGER
  dslRateXtucMaxInterleaveDelay INTEGER
  dslRateXtucMaxTxRate Unsigned32
  dslRateXtucMinTxRate Unsigned32
  dslRateXturMaxInterleaveDelay INTEGER
  dslRateXturMaxTxRate Unsigned32
  dslRateXturMinTxRate Unsigned32

SipProfileEntry  
SEQUENCE    
  sipProfileName DisplayString
  sipProfileSipSvr OCTET STRING
  sipProfileRegSvr OCTET STRING
  sipProfileProxySvr OCTET STRING
  sipProfileSipPort INTEGER
  sipProfileRegSvrPort INTEGER
  sipProfileProxySvrPort INTEGER
  sipProfileUriType INTEGER
  sipProfilePbit INTEGER
  sipProfileDscp INTEGER
  sipProfileKeepAlive INTEGER
  sipProfileSe INTEGER
  sipProfilePrack INTEGER
  sipProfileRowStatus RowStatus
  sipProfileRegExpire INTEGER

SipCallSvcProfileEntry  
SEQUENCE    
  sipCallSvcProfileName DisplayString
  sipCallSvcProfilePasswdOn INTEGER
  sipCallSvcProfilePasswd OCTET STRING
  sipCallSvcProfileNumberPlanOn INTEGER
  sipCallSvcProfileNumberPlanCc OCTET STRING
  sipCallSvcProfileNumberPlanNdc OCTET STRING
  sipCallSvcProfileNumberPlanTable OCTET STRING
  sipCallSvcProfileStateMask INTEGER
  sipCallSvcProfileDtmf INTEGER
  sipCallSvcProfileFax INTEGER
  sipCallSvcProfileRowStatus RowStatus
  sipCallSvcProfileFlashType INTEGER
  sipCallSvcProfileFlashInfo OCTET STRING
  sipCallSvcProfileSoftSwitchType INTEGER

DspProfileEntry  
SEQUENCE    
  dspProfileName DisplayString
  dspProfileCodec OCTET STRING
  dspProfilePlayBufferMinDelay INTEGER
  dspProfilePlayBufferMaxDelay INTEGER
  dspProfileEchoTail INTEGER
  dspProfileRowStatus RowStatus
  dspProfileG711Vpi INTEGER
  dspProfileG723Vpi INTEGER
  dspProfileG726Vpi INTEGER
  dspProfileG729Vpi INTEGER

H248ProfileEntry  
SEQUENCE    
  h248ProfileName DisplayString
  h248ProfileMgcSvr OCTET STRING
  h248ProfileMgcPort INTEGER
  h248ProfileMgc2On INTEGER
  h248ProfileMgc2Svr OCTET STRING
  h248ProfileMgc2Port INTEGER
  h248ProfileTransport INTEGER
  h248ProfileEncode INTEGER
  h248ProfilePbit INTEGER
  h248ProfileDscp INTEGER
  h248ProfileRowStatus RowStatus
  h248ProfileVbd INTEGER
  h248ProfileEphemeralPrefix OCTET STRING
  h248ProfileSoftswitch INTEGER
  h248ProfileForceVer INTEGER
  h248ProfileStartRTPPort INTEGER
  h248ProfileEndRTPPort INTEGER
  h248ProfileEphemeralStartNumber OCTET STRING
  h248ProfileEphemeralSuffixLength INTEGER
  h248ProfilePhysicalPrefix OCTET STRING
  h248ProfilePhysicalStartNumber OCTET STRING
  h248ProfilePhysicalSuffixLength INTEGER

DscpMappingEntry  
SEQUENCE    
  dscpSrcCodePoint INTEGER
  dscpMapPriority INTEGER

DscpPortEntry  
SEQUENCE    
  dscpStatusEnable INTEGER

VlanIsolationEntry  
SEQUENCE    
  vlanIsolationRowStatus INTEGER

DhcpRelay82Entry  
SEQUENCE    
  dhcpRelay82PrimaryServer IpAddress
  dhcpRelay82SecondaryServer IpAddress
  dhcpRelay82ActiveServer INTEGER
  dhcpRelay82Enable INTEGER
  dhcpRelay82Info DisplayString
  dhcpRelay82RelayMode INTEGER
  dhcpRelay82Suboption2Enable INTEGER
  dhcpRelay82Suboption2Info DisplayString
  dhcpRelay82EntryEnable INTEGER
  dhcpRelay82EntryOptionMode INTEGER
  dhcpRelay82VlanIp IpAddress
  dhcpRelay82VlanMask INTEGER
  dhcpRelay82VlanGateway IpAddress
  dhcpRelay82ThirdServer IpAddress
  dhcpRelay82FourthServer IpAddress
  dhcpRelay82FifthServer IpAddress
  dhcpRelay82ServerVid INTEGER

DhcpRelayArpShowEntry  
SEQUENCE    
  dhcpRelayArpShowVid INTEGER
  dhcpRelayArpShowIp IpAddress
  dhcpRelayArpShowMac PhysAddress

MacFilterPortEntry  
SEQUENCE    
  macFilterPortEnable INTEGER
  macFilterPortMacCount INTEGER
  macFilterPortFilterMode INTEGER

MacFilterEntry  
SEQUENCE    
  macFilterAddr PhysAddress
  macFilterRowStatus RowStatus

OuiFilterEntryOld  
SEQUENCE    
  ouiFilterAddrOld OCTET STRING
  ouiFilterRowStatusOld RowStatus

OuiFilterPortEntry  
SEQUENCE    
  ouiFilterPortEnable INTEGER
  ouiFilterPortFilterMode INTEGER

OuiFilterEntry  
SEQUENCE    
  ouiFilterAddr OCTET STRING
  ouiFilterRowStatus RowStatus

OuiFilterVlanEntry  
SEQUENCE    
  ouiFilterVlanEnable INTEGER
  ouiFilterVlanFilterMode INTEGER

DhcpSnoopPortEntry  
SEQUENCE    
  dhcpSnoopEnable INTEGER
  dhcpSnoopMaxcnt INTEGER
  dhcpSnoopSmacverifyEnable INTEGER

DhcpStaticEntry  
SEQUENCE    
  dhcpStaticIpAddr IpAddress
  dhcpStaticRowStatus RowStatus

AclSetEntry  
SEQUENCE    
  aclSetVpi INTEGER
  aclSetVci INTEGER
  aclSetProfileName DisplayString
  aclSetRowStatus RowStatus

AclProfileEntry  
SEQUENCE    
  aclProfileRuleName DisplayString
  aclProfileRuleNumber INTEGER
  aclProfileActionNumber INTEGER
  aclProfileRuleParamMask INTEGER
  aclProfileRuleEtype INTEGER
  aclProfileRuleVid INTEGER
  aclProfileRuleSmac PhysAddress
  aclProfileRuleDmac PhysAddress
  aclProfileRulePriority INTEGER
  aclProfileRuleProtocol INTEGER
  aclProfileRuleSrcIP IpAddress
  aclProfileRuleSrcIPMask INTEGER
  aclProfileRuleDestIP IpAddress
  aclProfileRuleDestIPMask INTEGER
  aclProfileRuleStartTos INTEGER
  aclProfileRuleEndTos INTEGER
  aclProfileRuleSrcStartPort INTEGER
  aclProfileRuleSrcEndPort INTEGER
  aclProfileRuleDestStartPort INTEGER
  aclProfileRuleDestEndPort INTEGER
  aclProfileActionRate INTEGER
  aclProfileActionrvlan INTEGER
  aclProfileActionrpri INTEGER
  aclProfileRowStatus RowStatus

PppoeAgentEntry  
SEQUENCE    
  pppoeAgentEnable INTEGER
  pppoeAgentInfo DisplayString
  pppoeAgentRowStatus RowStatus
  pppoeAgentOptionMode INTEGER

MacFfEntry  
SEQUENCE    
  macFfIndex INTEGER
  macFfVid INTEGER
  macFfArIP IpAddress
  macFfSrcIP IpAddress
  macFfSrcMask INTEGER
  macFfRowStatus RowStatus

MacFfVlanEntry  
SEQUENCE    
  macFfVlanRowstatus INTEGER
  macFfVlanUnknownUnicast INTEGER

MacFfStaticIPEntry  
SEQUENCE    
  macFfStaticIPPort INTEGER
  macFfStaticIPVid INTEGER
  macFfstaticIP IpAddress
  macFfStaticIPMask INTEGER
  macFfStaticIPRowStatus RowStatus

SecuredClientEntry  
SEQUENCE    
  securedClientIndex INTEGER
  securedClientStartIp IpAddress
  securedClientEndIp IpAddress
  securedClientService INTEGER
  securedClientEnable INTEGER

ExtAlarmEntry  
SEQUENCE    
  extAlarmIndex INTEGER
  extAlarmname OCTET STRING
  extAlarmstatus OCTET STRING
  extAlarmTriggeredMode INTEGER

UserEntry  
SEQUENCE    
  userName DisplayString
  userPassword DisplayString
  userPriviledge INTEGER
  userRowStatus RowStatus

IgmpGroupEntry  
SEQUENCE    
  igmpGroupIp IpAddress
  igmpGroupvid INTEGER
  igmpGroupnumberOfMembers INTEGER
  igmpGroupMemberPorts PortList

IgmpGroupPortEntry  
SEQUENCE    
  igmpGroupPortIp IpAddress
  igmpGroupPortvid INTEGER

IgmpGroupV2Entry  
SEQUENCE    
  igmpGroupV2Vid VlanIndex
  igmpGroupV2Ip IpAddress
  igmpGroupV2NumOfMembers INTEGER
  igmpGroupV2MemberPorts PortList

IgmpGroupPortV2Entry  
SEQUENCE    
  igmpGroupPortV2Vid VlanIndex
  igmpGroupPortV2Ip IpAddress
  igmpGroupPortV2SourceIp IpAddress

IgmpPortCtrlPduEntry  
SEQUENCE    
  igmpPortCtrlPduQueryCnt Counter32
  igmpPortCtrlPduReportCnt Counter32
  igmpPortCtrlPduLeaveCnt Counter32
  igmpPortNumOfActiveGroups INTEGER
  igmpPortCtrlAuditLeaveCnt Counter32

DhcpSnoopIpEntry  
SEQUENCE    
  dhcpSnoopIp IpAddress
  dhcpSnoopMac PhysAddress
  dhcpSnoopVid VlanIndex
  dhcpSnoopMask INTEGER
  dhcpSnoopGateway IpAddress
  dhcpSnoopRouteMap OCTET STRING

DhcpSnoopCounterEntry  
SEQUENCE    
  dhcpDiscovery Counter64
  dhcpOffer Counter64
  dhcpRequest Counter64
  dhcpAck Counter64
  dhcpAckBySnoopFull Counter64

DhcpRouteEntry  
SEQUENCE    
  dhcpRouteIndex INTEGER
  dhcpRouteVid VlanIndex
  dhcpRouteIP IpAddress
  dhcpRouteMask INTEGER
  dhcpRouteGwIP IpAddress

PaepvcSessionEntry  
SEQUENCE    
  paepvcSessionVpi INTEGER
  paepvcSessionVci INTEGER
  paepvcSessionState INTEGER
  paepvcSessionId INTEGER
  paepvcSessionUptime Unsigned32
  paepvcSessionacname DisplayString
  paepvcSessionsrvcname DisplayString

PaepvcCountEntry  
SEQUENCE    
  paepvcCountVpi INTEGER
  paepvcCountVci INTEGER
  paepvcCountPppLcpCfgReqRx Unsigned32
  paepvcCountPppLcpEchoReqRx Unsigned32
  paepvcCountPppLcpEchoReplyRx Unsigned32
  paepvcCountPadiTx Unsigned32
  paepvcCountPadoRx Unsigned32
  paepvcCountPadrTx Unsigned32
  paepvcCountPadsRx Unsigned32
  paepvcCountPadtTx Unsigned32
  paepvcCountPadtRx Unsigned32
  paepvcCountSrvcnameErrRx Unsigned32
  paepvcCountAcSystemErrRx Unsigned32
  paepvcCountGenericErrTx Unsigned32
  paepvcCountGenericErrRx Unsigned32

MacEntry  
SEQUENCE    
  macAddress MacAddress
  macPort INTEGER
  macStatus INTEGER

ArpproxyEntry  
SEQUENCE    
  arpproxyIp IpAddress
  arpproxyMac MacAddress
  arpproxyIfIndex INTEGER
  arpproxyVpi INTEGER
  arpproxyVci INTEGER
  arpproxyInterfaceIp IpAddress
  arpproxyInterfaceMask INTEGER
  arpproxyInterfaceVid VlanIndex
  arpproxyDhcpIp INTEGER
  arpproxyType INTEGER

IpbpvcIfDynamicEntry  
SEQUENCE    
  ipbpvcIfDynamicIp IpAddress
  ipbpvcIfDynamicMask INTEGER
  ipbpvcIfDynamicIfIndex INTEGER
  ipbpvcIfDynamicVpi INTEGER
  ipbpvcIfDynamicVci INTEGER

IpbpvcRouteDynamicEntry  
SEQUENCE    
  ipbpvcRouteDynamicType INTEGER
  ipbpvcRouteDynamicIp IpAddress
  ipbpvcRouteDynamicMask INTEGER
  ipbpvcRouteDynamicNextHop IpAddress
  ipbpvcRouteDynamicMetric INTEGER
  ipbpvcRouteDynamicPriority INTEGER

EnetSfpInfoEntry  
SEQUENCE    
  enetSfpInfoTxpower INTEGER
  enetSfpInfoRxpower INTEGER
  enetSfpInfoTemperature INTEGER
  enetSfpInfoTxBias INTEGER
  enetSfpInfoVoltage INTEGER

AdslPortUtilEntry  
SEQUENCE    
  adslPortUtilTx INTEGER
  adslPortUtilRx INTEGER

MacFfStatsEntry  
SEQUENCE    
  macFfStatsIndex INTEGER
  macFfStatsVid VlanIndex
  macFfStatsArIP IpAddress
  macFfStatsSrcIP IpAddress
  macFfStatsSrcMask INTEGER

MacFfArpEntry  
SEQUENCE    
  macFfArpVid VlanIndex
  macFfArpIP IpAddress
  macFfArpPort INTEGER
  macFfArpMac PhysAddress

MacFfArpCounterEntry  
SEQUENCE    
  macFfArpCounterRequestTX Counter32
  macFfArpCounterRequestRX Counter32
  macFfArpCounterRequestRXDrop Counter32
  macFfArpCounterReplyTX Counter32
  macFfArpCounterReplyRX Counter32
  macFfArpCounterReplyRXDrop Counter32

VoipLineStatusEntry  
SEQUENCE    
  voipLineStatusPhoneStatus INTEGER
  voipLineStatusServiceStatus INTEGER

VoipLineInfoEntry  
SEQUENCE    
  voipLineInfoSipLocalUri OCTET STRING
  voipLineInfoSipRemoteUri OCTET STRING
  voipLineInfoRtpTxCodecType OCTET STRING
  voipLineInfoRtpRxCodecType OCTET STRING
  voipLineInfoRtpTxPt INTEGER
  voipLineInfoRtpRxPt INTEGER
  voipLineInfoRtpLocalIp IpAddress
  voipLineInfoRtpRemoteIp IpAddress
  voipLineInfoRtpLocalPort INTEGER
  voipLineInfoRtpRemotePort INTEGER
  voipLineInfoSipLocalUri2 OCTET STRING
  voipLineInfoSipRemoteUri2 OCTET STRING
  voipLineInfoRtpTxCodecType2 OCTET STRING
  voipLineInfoRtpRxCodecType2 OCTET STRING
  voipLineInfoRtpTxPt2 INTEGER
  voipLineInfoRtpRxPt2 INTEGER
  voipLineInfoRtpLocalIp2 IpAddress
  voipLineInfoRtpRemoteIp2 IpAddress
  voipLineInfoRtpLocalPort2 INTEGER
  voipLineInfoRtpRemotePort2 INTEGER

VoipArpShowEntry  
SEQUENCE    
  voipArpShowIp IpAddress
  voipArpShowMac PhysAddress

VoipNumberPlanEntry  
SEQUENCE    
  voipNumberPlanName DisplayString
  voipNumberPlanIndex INTEGER
  voipNumberPlanPattern OCTET STRING
  voipNumberPlanRule OCTET STRING
  voipNumberPlanRowStatus RowStatus

VoipNumberPlanDftEntry  
SEQUENCE    
  voipNumberPlanDftRule OCTET STRING

VoipRouteEntry  
SEQUENCE    
  voipRouteIp IpAddress
  voipRouteGateway IpAddress
  voipRouteMask INTEGER
  voipRouteMetric INTEGER
  voipRouteRowStatus RowStatus

VoipRingEntry  
SEQUENCE    
  voipRingIndex INTEGER
  voipRingName DisplayString
  voipRingOn1 INTEGER
  voipRingOff1 INTEGER
  voipRingOn2 INTEGER
  voipRingOff2 INTEGER
  voipRingOn3 INTEGER
  voipRingOff3 INTEGER

Defined Values

calixNetworks 1.1.6321
OBJECT IDENTIFIER    

calixRegistrations 1.1.6321.1
OBJECT IDENTIFIER    

calixProducts 1.1.6321.1.2
OBJECT IDENTIFIER    

e5x100 1.1.6321.1.2.3
OBJECT IDENTIFIER    

e5x111 1.1.6321.1.2.3.2
OBJECT IDENTIFIER    

alarmconf 1.1.6321.1.2.3.2.2
OBJECT IDENTIFIER    

diagnostic 1.1.6321.1.2.3.2.4
OBJECT IDENTIFIER    

multicast 1.1.6321.1.2.3.2.7
OBJECT IDENTIFIER    

port 1.1.6321.1.2.3.2.8
OBJECT IDENTIFIER    

profile 1.1.6321.1.2.3.2.9
OBJECT IDENTIFIER    

switch 1.1.6321.1.2.3.2.10
OBJECT IDENTIFIER    

sys 1.1.6321.1.2.3.2.11
OBJECT IDENTIFIER    

trap 1.1.6321.1.2.3.2.12
OBJECT IDENTIFIER    

statistics 1.1.6321.1.2.3.2.13
OBJECT IDENTIFIER    

clear 1.1.6321.1.2.3.2.14
OBJECT IDENTIFIER    

voip 1.1.6321.1.2.3.2.16
OBJECT IDENTIFIER    

aesSeriesCommon 1.1.6321.1.2.3.2.97
OBJECT IDENTIFIER    

iesSeriesCommon 1.1.6321.1.2.3.2.98
OBJECT IDENTIFIER    

accessSwitchCommonATM 1.1.6321.1.2.3.2.99
OBJECT IDENTIFIER    

alarmOps 1.1.6321.1.2.3.2.2.1
The manager sets the corresponding bit value to 1 to start the operation and the agent clears the object to zero when the operation is successfully completed. The various bit positions are: BIT 1: clear BIT 2: cutoff
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

alarmConfTable 1.1.6321.1.2.3.2.2.2
This table includes alarm configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlarmConfEntry

alarmConfEntry 1.1.6321.1.2.3.2.2.2.1
An entry in alarmConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AlarmConfEntry  

alarmConfId 1.1.6321.1.2.3.2.2.2.1.1
5000:adslLine_up 5001:adslLine_down 5002:adslPerf_lol_thresh 5003:adslPerf_lof_thresh 5004:adslPerf_los_thresh 5005:adslPerf_lop_thresh 5006:adslPerf_es_thresh 5007:adslPerf_ses_thresh 5008:adslPerf_uas_thresh 5009:adslAtuc_loftrap 5010:adslAtuc_lostrap 5011:adslAtur_loftrap 5012:adslAtur_lostrap 5013:adslAtur_lprtrap 5014:ad_dhcp_rt_full 5015:ad_dhcp_dm_conflict 5016:ad_dhcp_entry_full 5017:ad_dhcp_ip_dup 5018:ad_dhcp_mac_dup 10000:eqptVol_err 10001:eqptEqpttemp_err 10002:eqptFan_err 10003:eqptHw_rtc_fail 10004:eqptHw_mon_fail 10005:eqptCold_start 10006:eqptWarm_start 10007:eqptAlm_input 10008:voip_battery_fail 10009:voip_clock_fail 10010:voip_ringer_fault 10011:eqptI2c_err 10012:eqptAlm_input2 10013:eqptAlm_input3 15000:sysReboot 15001:sysAco 15002:sysAlm_clear 15003:sysLogin_fail 15004:sysAnti_spoofing 15005:sysAlm_svrty_change 20000:enetUp 20001:enetDown 25000:voip_temp_error 25001:voip_dc_power_fail 25002:voip_ac_power_fail 25003:voip_ring_timer_fail 25004:voip_ring_rsrce_fail 25006:voip_call_setup_failed 25007:voip_call_threshold_violate
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmConfFacility 1.1.6321.1.2.3.2.2.2.1.2
Alarm facility.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER local1(1), local2(2), local3(3), local4(4), local5(5), local6(6), local7(7)  

alarmConfTarget 1.1.6321.1.2.3.2.2.2.1.3
The destination which alarms are reported to. Set the bit to 1 to enable the target. BIT 1: snmp trap BIT 2: syslog
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

alarmConfSeverity 1.1.6321.1.2.3.2.2.2.1.4
Alarm severity
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER critical(1), major(2), minor(3), info(4)  

alarmConfClearable 1.1.6321.1.2.3.2.2.2.1.5
Setting the object to one indicates that the alarm is to be cleared when user submits alarm clear.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clearable(1), unclearable(2)  

alarmCurrTable 1.1.6321.1.2.3.2.2.3
This table includes current alarm information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlarmCurrEntry

alarmCurrEntry 1.1.6321.1.2.3.2.2.3.1
An entry in alarmCurrTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AlarmCurrEntry  

alarmCurrIndex 1.1.6321.1.2.3.2.2.3.1.1
Index of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrOccurTime 1.1.6321.1.2.3.2.2.3.1.2
Alarm occurence time (in hundredths of a second) since the system was last re-initialized.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

alarmCurrTrapOid 1.1.6321.1.2.3.2.2.3.1.3
Trap OID of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

alarmCurrParam1 1.1.6321.1.2.3.2.2.3.1.4
The 1st parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrParam2 1.1.6321.1.2.3.2.2.3.1.5
The 2nd parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrParam3 1.1.6321.1.2.3.2.2.3.1.6
The 3rd parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrParam4 1.1.6321.1.2.3.2.2.3.1.7
The 4th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrParam5 1.1.6321.1.2.3.2.2.3.1.8
The 5th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrParam6 1.1.6321.1.2.3.2.2.3.1.9
The 6th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrParam7 1.1.6321.1.2.3.2.2.3.1.10
The 7th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrParam8 1.1.6321.1.2.3.2.2.3.1.11
The 8th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrTimeDescr 1.1.6321.1.2.3.2.2.3.1.12
The string representation of occurence time (YYYY/MM/DD HH:MM:SS).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

alarmCurrSeverity 1.1.6321.1.2.3.2.2.3.1.13
The severity of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER critical(1), major(2), minor(3), info(4)  

alarmCurrDescr 1.1.6321.1.2.3.2.2.3.1.14
The description of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

alarmSeverityPortTable 1.1.6321.1.2.3.2.2.4
This table includes the configuration of alarm reporting severity threshold for each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlarmSeverityPortEntry

alarmSeverityPortEntry 1.1.6321.1.2.3.2.2.4.1
An entry in alarmSeverityPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AlarmSeverityPortEntry  

severityThresh 1.1.6321.1.2.3.2.2.4.1.1
The minimum alarm severity that is reported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER critical(1), major(2), minor(3), info(4)  

selt 1.1.6321.1.2.3.2.4.3
OBJECT IDENTIFIER    

mlt 1.1.6321.1.2.3.2.4.4
OBJECT IDENTIFIER    

seltTarget 1.1.6321.1.2.3.2.4.3.1
IfIndex of the port which would be performed single end loopback test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

seltOps 1.1.6321.1.2.3.2.4.3.2
The manager sets the object to 1 to start the selt and the agent clears the object to zero when selt is successfully completed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

seltStatus 1.1.6321.1.2.3.2.4.3.3
Status description of the selt result.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

seltCableType 1.1.6321.1.2.3.2.4.3.4
The cable type that selt result indicates.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER awg24(1), awg26(2)  

seltLoopEstimateLengthFt 1.1.6321.1.2.3.2.4.3.5
The estimated loop length that selt result indicates.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

seltLoopEstimateLengthMeter 1.1.6321.1.2.3.2.4.3.6
The estimated loop length that selt result indicates.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltTarget 1.1.6321.1.2.3.2.4.4.1
IfIndex of the port which would be performed Metallic Link Test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mltOps 1.1.6321.1.2.3.2.4.4.2
The manager sets the object to 1 to start the mlt and the agent clears the object to zero when mlt is successfully completed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mltOption 1.1.6321.1.2.3.2.4.4.3
all : test all items vac: test AC voltage vdc: test DC voltage rload: test load resistance riso: test isolation resistance cap: test capacitor ren: test REN value ring: test ring voltage metering: test metering voltage
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), vac(2), vdc(3), rload(4), riso(5), cap(6), ren(7), ring(8), metering(9)  

mltForce 1.1.6321.1.2.3.2.4.4.4
Force test even the port is in use.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER force(1), notForce(2)  

mltResult 1.1.6321.1.2.3.2.4.4.5
OBJECT IDENTIFIER    

mltVacTip 1.1.6321.1.2.3.2.4.4.5.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltVacRing 1.1.6321.1.2.3.2.4.4.5.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltVacDiff 1.1.6321.1.2.3.2.4.4.5.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltVdcTip 1.1.6321.1.2.3.2.4.4.5.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltVdcRing 1.1.6321.1.2.3.2.4.4.5.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltVdcDiff 1.1.6321.1.2.3.2.4.4.5.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltRLoop 1.1.6321.1.2.3.2.4.4.5.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltRtg 1.1.6321.1.2.3.2.4.4.5.8
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltRrg 1.1.6321.1.2.3.2.4.4.5.9
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltRtr 1.1.6321.1.2.3.2.4.4.5.10
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltCtg 1.1.6321.1.2.3.2.4.4.5.11
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltCrg 1.1.6321.1.2.3.2.4.4.5.12
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltCtr 1.1.6321.1.2.3.2.4.4.5.13
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltRen 1.1.6321.1.2.3.2.4.4.5.14
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltVRing 1.1.6321.1.2.3.2.4.4.5.15
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltVMetering 1.1.6321.1.2.3.2.4.4.5.16
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltDialToneDetected 1.1.6321.1.2.3.2.4.4.5.17
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

mltDetectedDtmfCount 1.1.6321.1.2.3.2.4.4.5.18
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltDialToneDelay 1.1.6321.1.2.3.2.4.4.5.19
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltRelayTable 1.1.6321.1.2.3.2.4.4.6
Perform specified MLT relay function, or turn off MLT relay function in specified subscriber.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MltRelayEntry

mltRelayEntry 1.1.6321.1.2.3.2.4.4.6.1
An entry of mltRelayTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MltRelayEntry  

mltRelaySet 1.1.6321.1.2.3.2.4.4.6.1.1
By default, relay function is turned off.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER in(1), out(2), both(3), off(4)  

mcastBandwidth 1.1.6321.1.2.3.2.7.4
OBJECT IDENTIFIER    

igmpCount 1.1.6321.1.2.3.2.7.5
OBJECT IDENTIFIER    

mvlan 1.1.6321.1.2.3.2.7.6
OBJECT IDENTIFIER    

queryVid 1.1.6321.1.2.3.2.7.7
OBJECT IDENTIFIER    

igmpTimer 1.1.6321.1.2.3.2.7.11
OBJECT IDENTIFIER    

auditQuery 1.1.6321.1.2.3.2.7.12
OBJECT IDENTIFIER    

igmpProfile 1.1.6321.1.2.3.2.7.13
OBJECT IDENTIFIER    

igmpEnable 1.1.6321.1.2.3.2.7.1
Enable/disable IGMP protocol.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enableProxy(1), enableSnooping(2), disable(3)  

igmpVersion 1.1.6321.1.2.3.2.7.9
Setting IGMP version.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER v2(1), v3(2)  

igmpLeaveMode 1.1.6321.1.2.3.2.7.10
Configure IGMP leave message handling mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER immediateLeave(1), lastMemberQuery(2)  

mcastDefaultBandwidth 1.1.6321.1.2.3.2.7.4.1
Default bandwidth requirement for a multicast channel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..100000  

maxNumOfMcastBw 1.1.6321.1.2.3.2.7.4.2
The maximum number of row entries that user can create in mcastBwTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mcastBwTable 1.1.6321.1.2.3.2.7.4.3
This table defines bandwidth budget for a range of multicast IP channels.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McastBwEntry

mcastBwEntry 1.1.6321.1.2.3.2.7.4.3.1
An entry of mcastBwTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  McastBwEntry  

mcastBwIndex 1.1.6321.1.2.3.2.7.4.3.1.1
The index which specify the entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mcastBwStartIp 1.1.6321.1.2.3.2.7.4.3.1.2
The start multicast IP of the bandwidth control range.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

mcastBwEndIp 1.1.6321.1.2.3.2.7.4.3.1.3
The end multicast IP of the bandwidth control range.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

mcastBwBandwidth 1.1.6321.1.2.3.2.7.4.3.1.4
The bandwidth budget for the multicast IP channels.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

mcastBwRowStatus 1.1.6321.1.2.3.2.7.4.3.1.5
The row status of the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

mcastBwPortTable 1.1.6321.1.2.3.2.7.4.4
This table specify the multicast bandwidth control of the port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McastBwPortEntry

mcastBwPortEntry 1.1.6321.1.2.3.2.7.4.4.1
An entry of mcastBwPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  McastBwPortEntry  

mcastBwPortEnable 1.1.6321.1.2.3.2.7.4.4.1.1
Enable/disable multicast bandwidth control for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

mcastBwPortBandwidth 1.1.6321.1.2.3.2.7.4.4.1.2
Set bandwidth threshold for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

igmpCountPortTable 1.1.6321.1.2.3.2.7.5.1
This table specify the IGMP count limiting of the port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpCountPortEntry

igmpCountPortEntry 1.1.6321.1.2.3.2.7.5.1.1
An entry of igmpCountPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpCountPortEntry  

igmpCountPortEnable 1.1.6321.1.2.3.2.7.5.1.1.1
Enable/disable IGMP count limiting for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

igmpCountPortLimit 1.1.6321.1.2.3.2.7.5.1.1.2
The maximum allowed IGMP report count for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..16  

maxNumOfMvlan 1.1.6321.1.2.3.2.7.6.1
The maximum number of row entries that user can create in mvlanTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mvlanTable 1.1.6321.1.2.3.2.7.6.2
A table containing static configuration information for each multicast VLAN configured into the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MvlanEntry

mvlanEntry 1.1.6321.1.2.3.2.7.6.2.1
An entry of mvlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MvlanEntry  

mvlanIndex 1.1.6321.1.2.3.2.7.6.2.1.1
The VLAN-ID refering to this VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

mvlanName 1.1.6321.1.2.3.2.7.6.2.1.2
An administratively assigned string, which may be used to identify the VLAN.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

mvlanEgressPorts 1.1.6321.1.2.3.2.7.6.2.1.3
The set of ports which are permanently assigned to the egress list for this multicast VLAN.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

mvlanUntaggedPorts 1.1.6321.1.2.3.2.7.6.2.1.4
The set of ports which should transmit egress packets for this multicast VLAN as untagged.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

mvlanRowStatus 1.1.6321.1.2.3.2.7.6.2.1.5
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

mvlanTranslateTable 1.1.6321.1.2.3.2.7.6.3
A table that contains multicast to VLAN translation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MvlanTranslateEntry

mvlanTranslateEntry 1.1.6321.1.2.3.2.7.6.3.1
An entry of mvlanTranslateTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MvlanTranslateEntry  

mvlanTranslateIndex 1.1.6321.1.2.3.2.7.6.3.1.1
The index which specif the entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mvlanTranslateStartIp 1.1.6321.1.2.3.2.7.6.3.1.2
The start IP of the multicast VLAN translation.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

mvlanTranslateEndIp 1.1.6321.1.2.3.2.7.6.3.1.3
The end IP of the multicast VLAN translation.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

maxNumOfQryVid 1.1.6321.1.2.3.2.7.7.1
The maximum number of row entries that user can create in qryVidConfTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

qryVidConfTable 1.1.6321.1.2.3.2.7.7.2
This table defines statically set VLANs used for response IGMP report.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QryVidConfEntry

qryVidConfEntry 1.1.6321.1.2.3.2.7.7.2.1
An entry in qryVidConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  QryVidConfEntry  

qryVid 1.1.6321.1.2.3.2.7.7.2.1.1
VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

qryVidRowStatus 1.1.6321.1.2.3.2.7.7.2.1.2
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

qryVidStatusTable 1.1.6321.1.2.3.2.7.7.3
This table shows statically set or dynamically learned VLANs used for response IGMP report.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QryVidStatusEntry

qryVidStatusEntry 1.1.6321.1.2.3.2.7.7.3.1
An entry in qryVidStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  QryVidStatusEntry  

qryVidType 1.1.6321.1.2.3.2.7.7.3.1.1
VLAN type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

igmpQryInterval 1.1.6321.1.2.3.2.7.11.1
Set IGMP query interval, 10~1000 in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 10..1000  

igmpRobust 1.1.6321.1.2.3.2.7.11.2
Set IGMP query Robustness, 1~5.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..5  

igmpQryRespInterval 1.1.6321.1.2.3.2.7.11.3
Set IGMP query response interval, 1~100 in 100 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..100  

igmpLastMemQryInterval 1.1.6321.1.2.3.2.7.11.4
Set IGMP Last Member Query interval, 1~5 in 100 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..5  

igmpLastMemQryRobust 1.1.6321.1.2.3.2.7.11.5
Set Last Member Query Robustness, 1~5.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..5  

auditQryEnable 1.1.6321.1.2.3.2.7.12.1
Enable/disable IGMP audit query.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

auditQryInterval 1.1.6321.1.2.3.2.7.12.2
Set IGMP Audit Query Interval, 1~4 in 100 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4  

auditQryRobust 1.1.6321.1.2.3.2.7.12.3
Set IGMP Audit Query Robustness, 1~5.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..5  

maxNumberOfIgmpProfiles 1.1.6321.1.2.3.2.7.13.1
The max number of IGMP profiles in the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpProfileTable 1.1.6321.1.2.3.2.7.13.2
A table that contains IGMP Profiles.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpProfileEntry

igmpProfileEntry 1.1.6321.1.2.3.2.7.13.2.1
The entry of IGMP Profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpProfileEntry  

igmpProfileName 1.1.6321.1.2.3.2.7.13.2.1.1
The IGMP Profile name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

igmpProfileEnable 1.1.6321.1.2.3.2.7.13.2.1.2
Enable/disable IGMP Profile.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

igmpProfileMaxGroup 1.1.6321.1.2.3.2.7.13.2.1.3
Set maximum allowed multicast group, 1~64.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..64  

igmpProfileRowStatus 1.1.6321.1.2.3.2.7.13.2.1.4
The row status of the IGMP Profile entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

igmpFilterTable 1.1.6321.1.2.3.2.7.13.3
A table that contains IGMP Filters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpFilterEntry

igmpFilterEntry 1.1.6321.1.2.3.2.7.13.3.1
The entry of IGMP Filter table.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpFilterEntry  

igmpFilterIndex 1.1.6321.1.2.3.2.7.13.3.1.1
The index which specifies the filter rule.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpFilterStartIp 1.1.6321.1.2.3.2.7.13.3.1.2
The start IP of the filter rule.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

igmpFilterEndIp 1.1.6321.1.2.3.2.7.13.3.1.3
The end IP of the filter rule.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

igmpProfilePortTable 1.1.6321.1.2.3.2.7.13.4
This table specifies the IGMP Profile of the port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpProfilePortEntry

igmpProfilePortEntry 1.1.6321.1.2.3.2.7.13.4.1
An entry in igmpProfilePortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpProfilePortEntry  

igmpProfilePortProfile 1.1.6321.1.2.3.2.7.13.4.1.1
The IGMP Profile of the port.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..31)  

adslPort 1.1.6321.1.2.3.2.8.2
OBJECT IDENTIFIER    

pvc 1.1.6321.1.2.3.2.8.4
OBJECT IDENTIFIER    

ppvc 1.1.6321.1.2.3.2.8.5
OBJECT IDENTIFIER    

rpvc 1.1.6321.1.2.3.2.8.8
OBJECT IDENTIFIER    

paepvc 1.1.6321.1.2.3.2.8.10
OBJECT IDENTIFIER    

tlspvc 1.1.6321.1.2.3.2.8.11
OBJECT IDENTIFIER    

ipbpvc 1.1.6321.1.2.3.2.8.12
OBJECT IDENTIFIER    

voipPort 1.1.6321.1.2.3.2.8.13
OBJECT IDENTIFIER    

dtpvc 1.1.6321.1.2.3.2.8.14
OBJECT IDENTIFIER    

snrMgn 1.1.6321.1.2.3.2.8.15
OBJECT IDENTIFIER    

dslRate 1.1.6321.1.2.3.2.8.16
OBJECT IDENTIFIER    

gbond 1.1.6321.1.2.3.2.8.51
OBJECT IDENTIFIER    

subrPortTable 1.1.6321.1.2.3.2.8.1
This table includes subscriber attributes for the port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SubrPortEntry

subrPortEntry 1.1.6321.1.2.3.2.8.1.1
An entry in subrPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SubrPortEntry  

subrPortName 1.1.6321.1.2.3.2.8.1.1.1
Name of the subscriber.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

subrPortTel 1.1.6321.1.2.3.2.8.1.1.2
Telephone number of the subscriber.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

adslLineConfTable 1.1.6321.1.2.3.2.8.2.1
This table includes common attributes describing the ADSL line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslLineConfEntry

adslLineConfEntry 1.1.6321.1.2.3.2.8.2.1.1
An entry in adslLineConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslLineConfEntry  

adslLineConfAdslMode 1.1.6321.1.2.3.2.8.2.1.1.1
G.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER gDotLite(1), gDotDmt(2), t1Dot413(3), auto(4), etsi(5), adsl2(6), adsl2Plus(7)  

adslLineConfAnnexL 1.1.6321.1.2.3.2.8.2.1.1.2
Enable/disable annex L for the port(Only in AnnexA).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enableNarrowMode(1), enableWideMode(2), disable(3)  

adslLineConfAnnexM 1.1.6321.1.2.3.2.8.2.1.1.3
Enable/disable annex M for the port(For BCM AnnexA solution).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

adslLineConfAnnexI 1.1.6321.1.2.3.2.8.2.1.1.4
Enable/disable annex I for the port(For BCM AnnexA solution).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

adslLineConfOptionMask 1.1.6321.1.2.3.2.8.2.1.1.5
The semantic for each bit is: BIT 1 : Disable Trellis BIT 2 : Disable Reed-Solomon BIT 3 : Disable upstream bitswap BIT 4 : Disable downstream bitswap BIT 5 : Disable 1-bit constellation BIT 6 : Disable transmit windowing BIT 7 : Disable s=0.5 support (ADSL1 only) BIT 8 : Disable G.lite rate limit (ADSL1 only) BIT 9 : Enable Nitro BIT 10: Enable US PHYR BIT 11: ENABLE DS PHYR
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslLineConfPowerMgmt 1.1.6321.1.2.3.2.8.2.1.1.6
Enable/disable power management for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enableL2(1), enableL2(2), disable(3)  

adslLineConfPowerMode 1.1.6321.1.2.3.2.8.2.1.1.7
The power mode of the ADSL line.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fix(1), priorityToPower(2), priorityToRate(3)  

adslLineConfAturMaxTxPower 1.1.6321.1.2.3.2.8.2.1.1.8
The maximum allowed transmit power of ATU-R.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -130..200  

adslLineConfAtucMaxTxPower 1.1.6321.1.2.3.2.8.2.1.1.9
The maximum allowed transmit power of ATU-C.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -50..200  

adslLineConfMaxRxPower 1.1.6321.1.2.3.2.8.2.1.1.10
The maximum aggregate received power.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -255..255  

adslLineConfAturCarrierMask 1.1.6321.1.2.3.2.8.2.1.1.11
The upstream carrier mask. For CTLM AnnexA solution, bin is from 0 to 31; CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. Bit set to 1 indicates the bin is masked off.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adslLineConfAtucCarrierMask0 1.1.6321.1.2.3.2.8.2.1.1.12
The downstream carrier mask. For CTLM AnnexA solution, bin is from 32 to 255; CTLM AnnexB solution, bin is from 64 to 255; BCM solution, bin is from 32 to 255. Bit set to 1 indicates the bin is masked off.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adslLineConfAtucCarrierMask1 1.1.6321.1.2.3.2.8.2.1.1.13
The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adslLineConfAturInp 1.1.6321.1.2.3.2.8.2.1.1.14
The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER zero(1), zeroPointFive(2), one(3), two(4), four(5), eight(6), sixteen(7)  

adslLineConfAtucInp 1.1.6321.1.2.3.2.8.2.1.1.15
The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER zero(1), zeroPointFive(2), one(3), two(4), four(5), eight(6), sixteen(7)  

adslLineConfL0Time 1.1.6321.1.2.3.2.8.2.1.1.16
Set the minimum time in seconds that the ADSL line must stay in L0 power mode before changing to the L2 power mode. For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslLineConfL2Time 1.1.6321.1.2.3.2.8.2.1.1.17
Set minimum time in seconds that the ADSL line must stay in the L2 power mode before reducing the power again in the L2 power mode. For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslLineConfL2ATPR 1.1.6321.1.2.3.2.8.2.1.1.18
Set the maximum Aggregate Transmit Power Reduction (ATPR) in decibels (dB) that is permitted in a L2 power reduction. The system can gradually decrease the ADSL line transmission power while it is in the L2 power mode. This is the largest individual power reduction allowed in the L2 power mode. For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslLineConfL2ATPRT 1.1.6321.1.2.3.2.8.2.1.1.19
the maximum Aggregate Transmit Power Reduction Total (ATPRT) in decibels (dB) that is permitted in the L2 power mode. This is the total transmit power decrease that is allowed to occur in the L2 power mode. For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslLineConfMaxL2Rate 1.1.6321.1.2.3.2.8.2.1.1.20
configured maximum L2 rate. (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslLineConfMinL2Rate 1.1.6321.1.2.3.2.8.2.1.1.21
configured minimum L2 rate. (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslLineConfL0toL2Rate 1.1.6321.1.2.3.2.8.2.1.1.22
configured transition L0 to L2 rate. (<=min_l2rate/2 and >= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslLineConfNitro 1.1.6321.1.2.3.2.8.2.1.1.23
Enable/disable nitro mode for the port(For BCM solution).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

adslLineConfUSPhyr 1.1.6321.1.2.3.2.8.2.1.1.24
Enable/disable Upstream PHYR for the port(For BCM solution).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

adslLineConfDSPhyr 1.1.6321.1.2.3.2.8.2.1.1.25
Enable/disable Downstream PHYR for the port(For BCM solution).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

adslPortBatchSet 1.1.6321.1.2.3.2.8.2.3
OBJECT IDENTIFIER    

adslPortTarget 1.1.6321.1.2.3.2.8.2.3.1
The managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chaises) Byte 2~3: 0,0 Reserved(slot) Byte 4: 0, reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adslPortOps 1.1.6321.1.2.3.2.8.2.3.2
The managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: enable port BIT 2: disable port BIT 3: set ADSL mode BIT 4: set line profile BIT 5: set alarm profile BIT 6: enable Annex L to be narrow mode(Only in AnnexA) BIT 7: enable Annex L to be wide mode(Only in AnnexA) BIT 8: disable Annex L(Only in AnnexA) BIT 9: enable Annex M (For BCM AnnexA solution) BIT 10: disable Annex M (For BCM AnnexA solution) BIT 11: enable Annex I (For BCM AnnexA solution) BIT 12: disable Annex I (For BCM AnnexA solution) BIT 13: set option mask BIT 14: enable power management mode to be L2 BIT 15: enable power management mode to be L2 BIT 16: disable power management mode BIT 17: set power mode to be fixed BIT 18: set power mode to be priority to power BIT 19: set power mode to be priority to rate BIT 20: set ATU-R max Tx power BIT 21: set ATU-C max Tx power BIT 22: set max Rx power BIT 23: set ATU-R carrier mask BIT 24: set ATU-C carrier mask BIT 25: set ATU-R INP minimum setting BIT 26: set ATU-C INP minimum setting
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslPortOps2 1.1.6321.1.2.3.2.8.2.3.3
The managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: set L0 Time BIT 2: set L2 Time BIT 3: set L2 ATPR BIT 4: set L2 ATPRT BIT 5: set maximum L2 rate BIT 6: set minimum L2 rate BIT 7: set transition L0 to L2 rate
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslModeForBatchSet 1.1.6321.1.2.3.2.8.2.3.4
G.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER gDotLite(1), gDotDmt(2), t1Dot413(3), auto(4), etsi(5), adsl2(6), adsl2Plus(7)  

adslLineProfileForBatchSet 1.1.6321.1.2.3.2.8.2.3.5
The ADSL line profile.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

adslAlarmProfileForBatchSet 1.1.6321.1.2.3.2.8.2.3.6
The ADSL alarm profile.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

adslOptionMaskForBatchSet 1.1.6321.1.2.3.2.8.2.3.7
The semantic for each bit is identical to the object adslLineConfOptionMask.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslAturMaxTxPowerForBatchSet 1.1.6321.1.2.3.2.8.2.3.8
The maximum allowed transmit power of ATU-R.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -130..200  

adslAtucMaxTxPowerForBatchSet 1.1.6321.1.2.3.2.8.2.3.9
The maximum allowed transmit power of ATU-C.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -50..200  

adslMaxRxPowerForBatchSet 1.1.6321.1.2.3.2.8.2.3.10
The maximum aggregate received power.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -255..255  

adslAturCarrierMaskForBatchSet 1.1.6321.1.2.3.2.8.2.3.11
The upstream carrier mask.For CTLM AnnexA solution, bin is from 0 to 31; CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. Bit set to 1 indicates the bin is masked off.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adslAtucCarrierMask0ForBatchSet 1.1.6321.1.2.3.2.8.2.3.12
The downstream carrier mask from bin 32 to 255. Bit set to 1 indicates the bin is masked off.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adslAtucCarrierMask1ForBatchSet 1.1.6321.1.2.3.2.8.2.3.13
The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adslAturInpForBatchSet 1.1.6321.1.2.3.2.8.2.3.14
The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER zero(1), zeroPointFive(2), one(3), two(4), four(5), eight(6), sixteen(7)  

adslAtucInpForBatchSet 1.1.6321.1.2.3.2.8.2.3.15
The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER zero(1), zeroPointFive(2), one(3), two(4), four(5), eight(6), sixteen(7)  

adslL0TimeForBatchSet 1.1.6321.1.2.3.2.8.2.3.16
Set the minimum time in seconds that the ADSL line must stay in L0 power mode before changing to the L2 power mode. For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslL2TimeForBatchSet 1.1.6321.1.2.3.2.8.2.3.17
Set minimum time in seconds that the ADSL line must stay in the L2 power mode before reducing the power again in the L2 power mode. For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslL2ATPRForBatchSet 1.1.6321.1.2.3.2.8.2.3.18
Set the maximum Aggregate Transmit Power Reduction (ATPR) in decibels (dB) that is permitted in a L2 power reduction. The system can gradually decrease the ADSL line transmission power while it is in the L2 power mode. This is the largest individual power reduction allowed in the L2 power mode. For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslL2ATPRTForBatchSet 1.1.6321.1.2.3.2.8.2.3.19
the maximum Aggregate Transmit Power Reduction Total (ATPRT) in decibels (dB) that is permitted in the L2 power mode. This is the total transmit power decrease that is allowed to occur in the L2 power mode. For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslMaxL2RateForBatchSet 1.1.6321.1.2.3.2.8.2.3.20
configured maximum L2 rate. (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslMinL2RateForBatchSet 1.1.6321.1.2.3.2.8.2.3.21
configured minimum L2 rate. (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslL0toL2RateForBatchSet 1.1.6321.1.2.3.2.8.2.3.22
configured transition L0 to L2 rate. (<=min_l2rate/2 and >= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslLineStatusTable 1.1.6321.1.2.3.2.8.2.4
This table includes the ADSL line status.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslLineStatusEntry

adslLineStatusEntry 1.1.6321.1.2.3.2.8.2.4.1
An entry in adslLineStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslLineStatusEntry  

adslLineStatusMode 1.1.6321.1.2.3.2.8.2.4.1.1
The link up mode of the ADSL line.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER gDotLite(1), gDotDmt(2), t1Dot413(3), etsi(4), adsl2(5), adsl2Plus(6), none(7)  

adslLineUpTime 1.1.6321.1.2.3.2.8.2.4.1.2
The link up time of the ADSL line, in unit of seconds
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

powerMgmtParamTable 1.1.6321.1.2.3.2.8.2.5
This table defines L0 to L2 power transition parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PowerMgmtParamEntry

powerMgmtParamEntry 1.1.6321.1.2.3.2.8.2.5.1
An entry in powerMgmtParamTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PowerMgmtParamEntry  

powerMgmtL0Time 1.1.6321.1.2.3.2.8.2.5.1.1
The object specifies the minimum time in L0 mode before L2 mode may be entered.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtL2Time 1.1.6321.1.2.3.2.8.2.5.1.2
The object specifies the minimum time in L2 mode before trimming and in between power trims.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtL2Atpr 1.1.6321.1.2.3.2.8.2.5.1.3
The maximum Aggregate Transmit Power Reduction.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtL2Atprt 1.1.6321.1.2.3.2.8.2.5.1.4
The maximum Aggregate Transmit Power Reduction Total.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtL2MinRate 1.1.6321.1.2.3.2.8.2.5.1.5
The object specifies the minimum L2 rate.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtL2MaxRate 1.1.6321.1.2.3.2.8.2.5.1.6
The object specifies the maximum L2 rate.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtL2ThreshRate 1.1.6321.1.2.3.2.8.2.5.1.7
The object specifies the rate threshold that triggers the line entering L0 or L2 mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtPSDTable 1.1.6321.1.2.3.2.8.2.6
This table provides the PSD setting for both ATU-C and ATU-R.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PowerMgmtPSDEntry

powerMgmtPSDEntry 1.1.6321.1.2.3.2.8.2.6.1
An entry in powerMgmtPSDTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PowerMgmtPSDEntry  

powerMgmtAtucMaxPSD 1.1.6321.1.2.3.2.8.2.6.1.1
The object specifies the maximum ATU-C PSD.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtAturMaxPSD 1.1.6321.1.2.3.2.8.2.6.1.2
The object specifies the maximum ATU-R PSD.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

maxNumOfPvcs 1.1.6321.1.2.3.2.8.4.1
The maximum number of PVCs which could be created on a port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

pvcTable 1.1.6321.1.2.3.2.8.4.2
This table includes PVC configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PvcEntry

pvcEntry 1.1.6321.1.2.3.2.8.4.2.1
An entry in pvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PvcEntry  

pvcVpi 1.1.6321.1.2.3.2.8.4.2.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

pvcVci 1.1.6321.1.2.3.2.8.4.2.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

pvcPvid 1.1.6321.1.2.3.2.8.4.2.1.3
Default VID of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

pvcPriority 1.1.6321.1.2.3.2.8.4.2.1.5
802.1p default priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

pvcProfileDS 1.1.6321.1.2.3.2.8.4.2.1.6
The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

pvcRowStatus 1.1.6321.1.2.3.2.8.4.2.1.7
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pvcProfileUS 1.1.6321.1.2.3.2.8.4.2.1.8
The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

pvcAcName 1.1.6321.1.2.3.2.8.4.2.1.11
Access concentrator name for paepvc.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

pvcServiceName 1.1.6321.1.2.3.2.8.4.2.1.12
Service name for paepvc.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

pvcHelloTime 1.1.6321.1.2.3.2.8.4.2.1.13
The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

pvcStateTable 1.1.6321.1.2.3.2.8.4.3
This table show current PVC status.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PvcStateEntry

pvcStateEntry 1.1.6321.1.2.3.2.8.4.3.1
An entry in pvcStateTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PvcStateEntry  

pvcStateVpi 1.1.6321.1.2.3.2.8.4.3.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

pvcStateVci 1.1.6321.1.2.3.2.8.4.3.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

pvcStatePvid 1.1.6321.1.2.3.2.8.4.3.1.3
Default VID of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

pvcStatePriority 1.1.6321.1.2.3.2.8.4.3.1.4
802.1p default priority of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

pvcStateChannelType 1.1.6321.1.2.3.2.8.4.3.1.8
The value of this object identifies the channel type at runtime.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

pvcStateEncap 1.1.6321.1.2.3.2.8.4.3.1.9
The value of this object identifies the channel encapsulation at runtime.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

pvcUsRateLimitTable 1.1.6321.1.2.3.2.8.4.4
This table defines the upstream rate limit for each PVC.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PvcUsRateLimitEntry

pvcUsRateLimitEntry 1.1.6321.1.2.3.2.8.4.4.1
An entry in pvcUsRateLimitTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PvcUsRateLimitEntry  

pvcUsRateLimitEnable 1.1.6321.1.2.3.2.8.4.4.1.1
Enable/disable upstream rate limit for a PVC.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

pvcUsRateLimit 1.1.6321.1.2.3.2.8.4.4.1.2
Upstream rate limit in Kbps for a PVC.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

maxNumOfPriorityPvcs 1.1.6321.1.2.3.2.8.5.1
The maximum number of priority PVCs which could be created on a port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ppvcTable 1.1.6321.1.2.3.2.8.5.2
This table includes priority PVC configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PpvcEntry

ppvcEntry 1.1.6321.1.2.3.2.8.5.2.1
An entry in ppvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PpvcEntry  

ppvcVpi 1.1.6321.1.2.3.2.8.5.2.1.1
VPI of the ppvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

ppvcVci 1.1.6321.1.2.3.2.8.5.2.1.2
VCI of the ppvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

ppvcPvid 1.1.6321.1.2.3.2.8.5.2.1.3
Default VID of the ppvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

ppvcEncap 1.1.6321.1.2.3.2.8.5.2.1.4
Encapsulation of the ppvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER llc(1), vc(2)  

ppvcPriority 1.1.6321.1.2.3.2.8.5.2.1.5
802.1p default priority of the ppvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

ppvcRowStatus 1.1.6321.1.2.3.2.8.5.2.1.6
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ppvcMemberTable 1.1.6321.1.2.3.2.8.5.4
This table includes priority PVC member configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PpvcMemberEntry

ppvcMemberEntry 1.1.6321.1.2.3.2.8.5.4.1
An entry in ppvcMemberTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PpvcMemberEntry  

ppvcMemberVpi 1.1.6321.1.2.3.2.8.5.4.1.1
VPI of the member ppvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

ppvcMemberVci 1.1.6321.1.2.3.2.8.5.4.1.2
VCI of the member ppvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

ppvcMemberPriority 1.1.6321.1.2.3.2.8.5.4.1.3
802.1p default priority of the member ppvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

ppvcMemberProfileDS 1.1.6321.1.2.3.2.8.5.4.1.4
The profile of the member ppvc in DS side.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

ppvcMemberRowStatus 1.1.6321.1.2.3.2.8.5.4.1.5
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ppvcMemberProfileUS 1.1.6321.1.2.3.2.8.5.4.1.6
The profile of the member ppvc in US side.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

rpvcGatewayTable 1.1.6321.1.2.3.2.8.8.1
This table includes Routed Gateway configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RpvcGatewayEntry

rpvcGatewayEntry 1.1.6321.1.2.3.2.8.8.1.1
An entry in Routed Gateway table.
Status: current Access: not-accessible
OBJECT-TYPE    
  RpvcGatewayEntry  

rpvcGatewayIp 1.1.6321.1.2.3.2.8.8.1.1.1
IP of RPVC gateway.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

rpvcGatewayVlanId 1.1.6321.1.2.3.2.8.8.1.1.2
Vlan id send to this RPVC gateway.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

rpvcGatewayRowStatus 1.1.6321.1.2.3.2.8.8.1.1.3
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

rpvcGatewayPriority 1.1.6321.1.2.3.2.8.8.1.1.4
802.1p p bit send to this RPVC gateway.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

rpvcTable 1.1.6321.1.2.3.2.8.8.2
This table includes RPVC configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RpvcEntry

rpvcEntry 1.1.6321.1.2.3.2.8.8.2.1
An entry in rpvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  RpvcEntry  

rpvcVpi 1.1.6321.1.2.3.2.8.8.2.1.1
VPI of the rpvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

rpvcVci 1.1.6321.1.2.3.2.8.8.2.1.2
VCI of the rpvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

rpvcDSProfile 1.1.6321.1.2.3.2.8.8.2.1.3
The down stream profile of the rpvc.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

rpvcUSProfile 1.1.6321.1.2.3.2.8.8.2.1.4
The up stream profile of the rpvc.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

rpvcIp 1.1.6321.1.2.3.2.8.8.2.1.5
The IP of the rpvc.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

rpvcNetmask 1.1.6321.1.2.3.2.8.8.2.1.6
The IP mask of the rpvc IP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

rpvcGatewayIpAddress 1.1.6321.1.2.3.2.8.8.2.1.7
The gateway IP of rpvc.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

rpvcRowStatus 1.1.6321.1.2.3.2.8.8.2.1.8
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

rpvcRouteDomainTable 1.1.6321.1.2.3.2.8.8.3
This table includes RPVC route domain configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RpvcRouteDomainEntry

rpvcRouteDomainEntry 1.1.6321.1.2.3.2.8.8.3.1
An entry in rpvcRouteDomainTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  RpvcRouteDomainEntry  

rpvcRouteDomainVpi 1.1.6321.1.2.3.2.8.8.3.1.1
VPI of the rpvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

rpvcRouteDomainVci 1.1.6321.1.2.3.2.8.8.3.1.2
VCI of the rpvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

rpvcRouteDomainIp 1.1.6321.1.2.3.2.8.8.3.1.3
The route domain IP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

rpvcRouteDomainNetmask 1.1.6321.1.2.3.2.8.8.3.1.4
The IP mask of the route domain IP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

rpvcRouteDomainRowStatus 1.1.6321.1.2.3.2.8.8.3.1.5
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

rpvcArpAgingTime 1.1.6321.1.2.3.2.8.8.4
Set RPVC ARP proxy aging time 10..10000 seconds, 0 to disable againg.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

rpvcArpFlush 1.1.6321.1.2.3.2.8.8.5
Flush the RPVC ARP proxy table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1)  

dsBcastDisableTable 1.1.6321.1.2.3.2.8.9
This table includes Down Stream Bcast configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DsBcastDisableEntry

dsBcastDisableEntry 1.1.6321.1.2.3.2.8.9.1
An entry in Down Stream Bcast table.
Status: current Access: not-accessible
OBJECT-TYPE    
  DsBcastDisableEntry  

dsBcastDisableVlanId 1.1.6321.1.2.3.2.8.9.1.1
downstream broadcast disabled vid.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dsBcastDisableRowStatus 1.1.6321.1.2.3.2.8.9.1.2
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

paepvcTable 1.1.6321.1.2.3.2.8.10.1
This table includes PPPoAoE PVC configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PaepvcEntry

paepvcEntry 1.1.6321.1.2.3.2.8.10.1.1
An entry of paepvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PaepvcEntry  

paepvcVpi 1.1.6321.1.2.3.2.8.10.1.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

paepvcVci 1.1.6321.1.2.3.2.8.10.1.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

paepvcPvid 1.1.6321.1.2.3.2.8.10.1.1.3
Default VID of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

paepvcPriority 1.1.6321.1.2.3.2.8.10.1.1.5
802.1p default priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

paepvcProfileDS 1.1.6321.1.2.3.2.8.10.1.1.6
The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

paepvcAcName 1.1.6321.1.2.3.2.8.10.1.1.7
Access concentrator name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

paepvcServiceName 1.1.6321.1.2.3.2.8.10.1.1.8
Service name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

paepvcHelloTime 1.1.6321.1.2.3.2.8.10.1.1.9
The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

paepvcRowStatus 1.1.6321.1.2.3.2.8.10.1.1.10
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

paepvcProfileUS 1.1.6321.1.2.3.2.8.10.1.1.11
The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

paepvcCvid 1.1.6321.1.2.3.2.8.10.1.1.12
Default C-VID of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  VlanIndex  

paepvcCPriority 1.1.6321.1.2.3.2.8.10.1.1.13
802.1p default C-priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

tlspvcTable 1.1.6321.1.2.3.2.8.11.1
This table includes Transparent LAN Service (TLS) PVC configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TlspvcEntry

tlspvcEntry 1.1.6321.1.2.3.2.8.11.1.1
An entry of tlspvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  TlspvcEntry  

tlspvcVpi 1.1.6321.1.2.3.2.8.11.1.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

tlspvcVci 1.1.6321.1.2.3.2.8.11.1.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

tlspvcSvid 1.1.6321.1.2.3.2.8.11.1.1.3
s-tag VLAN ID of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

tlspvcSpriority 1.1.6321.1.2.3.2.8.11.1.1.5
s-tag priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

tlspvcProfileDS 1.1.6321.1.2.3.2.8.11.1.1.6
The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

tlspvcRowStatus 1.1.6321.1.2.3.2.8.11.1.1.7
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tlspvcProfileUS 1.1.6321.1.2.3.2.8.11.1.1.8
The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

ipbpvcDomainTable 1.1.6321.1.2.3.2.8.12.1
This table includes ipbpvc domain configuration. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcDomainEntry

ipbpvcDomainEntry 1.1.6321.1.2.3.2.8.12.1.1
An entry of ipbpvcDomainTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcDomainEntry  

ipbpvcDomainName 1.1.6321.1.2.3.2.8.12.1.1.1
Name of the domain.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ipbpvcDomainRowStatus 1.1.6321.1.2.3.2.8.12.1.1.2
Row status of the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipbpvcDomainVlanTable 1.1.6321.1.2.3.2.8.12.2
This table includes ipbpvc domain VLAN configuration. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcDomainVlanEntry

ipbpvcDomainVlanEntry 1.1.6321.1.2.3.2.8.12.2.1
An entry of ipbpvcDomainVlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcDomainVlanEntry  

ipbpvcDomainVlanId 1.1.6321.1.2.3.2.8.12.2.1.1
Set VLAN to join or leave the specified domain.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

ipbpvcDomainDhcpVlanEnable 1.1.6321.1.2.3.2.8.12.2.1.2
Enable/disable DHCP VLAN in a domain.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ipbpvcDomainVlanRowStatus 1.1.6321.1.2.3.2.8.12.2.1.3
Row status of the table used to create/delete an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipbpvcEdgeRouterTable 1.1.6321.1.2.3.2.8.12.3
This table includes ipbpvc edge router configuration. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcEdgeRouterEntry

ipbpvcEdgeRouterEntry 1.1.6321.1.2.3.2.8.12.3.1
An entry of ipbpvcEdgeRouterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcEdgeRouterEntry  

ipbpvcEdgeRouterIp 1.1.6321.1.2.3.2.8.12.3.1.1
IP address of the edge router.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipbpvcEdgeRouterVid 1.1.6321.1.2.3.2.8.12.3.1.2
VLAN ID of the edge router.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

ipbpvcEdgeRouterMask 1.1.6321.1.2.3.2.8.12.3.1.3
Netmask of the edge router.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcEdgeRouterRowStatus 1.1.6321.1.2.3.2.8.12.3.1.4
Row status of the table used to create/delete an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipbpvcInterfaceTable 1.1.6321.1.2.3.2.8.12.4
This table includes ipbpvc interface configuration. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcInterfaceEntry

ipbpvcInterfaceEntry 1.1.6321.1.2.3.2.8.12.4.1
An entry of ipbpvcInterfaceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcInterfaceEntry  

ipbpvcInterfaceIp 1.1.6321.1.2.3.2.8.12.4.1.1
IP address of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipbpvcInterfaceMask 1.1.6321.1.2.3.2.8.12.4.1.2
Netmask of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcInterfaceVid 1.1.6321.1.2.3.2.8.12.4.1.3
VLAN ID of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

ipbpvcInterfaceIfIndex 1.1.6321.1.2.3.2.8.12.4.1.4
IfIndex of the interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

ipbpvcInterfaceVpi 1.1.6321.1.2.3.2.8.12.4.1.5
VPI of the interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

ipbpvcInterfaceVci 1.1.6321.1.2.3.2.8.12.4.1.6
VCI of the interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

ipbpvcInterfaceRowStatus 1.1.6321.1.2.3.2.8.12.4.1.7
Row status of the table used to create/delete an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipbpvcRouteTable 1.1.6321.1.2.3.2.8.12.5
This table includes ipbpvc route configuration. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcRouteEntry

ipbpvcRouteEntry 1.1.6321.1.2.3.2.8.12.5.1
An entry of ipbpvcRouteTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcRouteEntry  

ipbpvcRouteIp 1.1.6321.1.2.3.2.8.12.5.1.1
IP address of the route.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipbpvcRouteMask 1.1.6321.1.2.3.2.8.12.5.1.2
Netmask of the route.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcRouteNextHop 1.1.6321.1.2.3.2.8.12.5.1.3
Next hop IP address of the route.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipbpvcRouteMetric 1.1.6321.1.2.3.2.8.12.5.1.4
Metric of the route.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..15  

ipbpvcRoutePriority 1.1.6321.1.2.3.2.8.12.5.1.5
Priority of the route. Note that the default value of this object is 8, which means we keep the original priority of the packet(frame).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

ipbpvcRouteRowStatus 1.1.6321.1.2.3.2.8.12.5.1.6
Row status of the table used to create/delete an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipbpvcTable 1.1.6321.1.2.3.2.8.12.6
This table includes ipbpvc configuration. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcEntry

ipbpvcEntry 1.1.6321.1.2.3.2.8.12.6.1
An entry of ipbpvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcEntry  

ipbpvcVpi 1.1.6321.1.2.3.2.8.12.6.1.1
VPI of the PVC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcVci 1.1.6321.1.2.3.2.8.12.6.1.2
VCI of the PVC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcPvid 1.1.6321.1.2.3.2.8.12.6.1.3
PVID of the PVC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcEncap 1.1.6321.1.2.3.2.8.12.6.1.4
Type of the PVC.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ipoe(1), reserved(2), ipoa(3)  

ipbpvcPriority 1.1.6321.1.2.3.2.8.12.6.1.5
Priority of the PVC.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

ipbpvcProfile 1.1.6321.1.2.3.2.8.12.6.1.6
Profile of the PVC.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

ipbpvcRowStatus 1.1.6321.1.2.3.2.8.12.6.1.7
Row status of the table used to create/delete an entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

ipbpvcProfileUS 1.1.6321.1.2.3.2.8.12.6.1.8
US Profile of the PVC.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

arpproxy 1.1.6321.1.2.3.2.8.12.8
OBJECT IDENTIFIER    

arpproxyAge 1.1.6321.1.2.3.2.8.12.8.1
Aging time of the ARP proxy. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 10..10000  

arpproxyFlush 1.1.6321.1.2.3.2.8.12.8.2
OBJECT IDENTIFIER    

arpproxyFlushTarget 1.1.6321.1.2.3.2.8.12.8.2.1
The target whose ARP table to be flushed. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), edgerouter(2), interface(3)  

arpproxyFlushOps 1.1.6321.1.2.3.2.8.12.8.2.2
Set the object to 1 to start flushing. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

arpproxyFlushEdgeRouterIp 1.1.6321.1.2.3.2.8.12.8.2.3
Flush ARP table for the specified edge router. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

arpproxyFlushEdgeRouterVid 1.1.6321.1.2.3.2.8.12.8.2.4
Flush ARP table for the specified edge router. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

arpproxyFlushInterfaceIp 1.1.6321.1.2.3.2.8.12.8.2.5
Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

arpproxyFlushInterfaceMask 1.1.6321.1.2.3.2.8.12.8.2.6
Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

arpproxyFlushInterfaceVid 1.1.6321.1.2.3.2.8.12.8.2.7
Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

dtpvcTable 1.1.6321.1.2.3.2.8.14.1
This table includes Double Tagging (DT) PVC configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DtpvcEntry

dtpvcEntry 1.1.6321.1.2.3.2.8.14.1.1
An entry of dtpvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DtpvcEntry  

dtpvcVpi 1.1.6321.1.2.3.2.8.14.1.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

dtpvcVci 1.1.6321.1.2.3.2.8.14.1.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

dtpvcSvid 1.1.6321.1.2.3.2.8.14.1.1.3
s-tag VLAN ID of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

dtpvcSpriority 1.1.6321.1.2.3.2.8.14.1.1.4
s-tag priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

dtpvcCvid 1.1.6321.1.2.3.2.8.14.1.1.5
c-tag VLAN ID of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  VlanIndex  

dtpvcCpriority 1.1.6321.1.2.3.2.8.14.1.1.6
c-tag priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

dtpvcDSProfile 1.1.6321.1.2.3.2.8.14.1.1.7
The value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in DS side.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

dtpvcUSProfile 1.1.6321.1.2.3.2.8.14.1.1.8
The value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in US side.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

dtpvcRowStatus 1.1.6321.1.2.3.2.8.14.1.1.9
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

dtpvcSuperChannel 1.1.6321.1.2.3.2.8.14.1.1.10
Specified the configured DTPVC is a super channel.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dtpvcAcName 1.1.6321.1.2.3.2.8.14.1.1.11
Access concentrator name for paepvc.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

dtpvcServiceName 1.1.6321.1.2.3.2.8.14.1.1.12
Service name for paepvc.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

dtpvcHelloTime 1.1.6321.1.2.3.2.8.14.1.1.13
The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

dtpvcStateTable 1.1.6321.1.2.3.2.8.14.2
This table show current DTPVC status.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DtpvcStateEntry

dtpvcStateEntry 1.1.6321.1.2.3.2.8.14.2.1
An entry in dtpvcStateTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DtpvcStateEntry  

dtpvcStateVpi 1.1.6321.1.2.3.2.8.14.2.1.1
VPI of the dtpvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

dtpvcStateVci 1.1.6321.1.2.3.2.8.14.2.1.2
VCI of the dtpvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

dtpvcStateSvid 1.1.6321.1.2.3.2.8.14.2.1.3
Default S-VID of the dtpvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

dtpvcStateSPriority 1.1.6321.1.2.3.2.8.14.2.1.4
S-priority of the dtpvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

dtpvcStateCvid 1.1.6321.1.2.3.2.8.14.2.1.5
Default C-VID of the dtpvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

dtpvcStateCPriority 1.1.6321.1.2.3.2.8.14.2.1.6
C-priority of the dtpvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

dtpvcStateChannelType 1.1.6321.1.2.3.2.8.14.2.1.8
The value of this object identifies the channel type at runtime.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

dtpvcStateEncap 1.1.6321.1.2.3.2.8.14.2.1.9
The value of this object identifies the channel encapsulation at runtime.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

gbondGroupTable 1.1.6321.1.2.3.2.8.51.1
A table containing the G.Bond configuration information for each bonding group of the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GbondGroupEntry

gbondGroupEntry 1.1.6321.1.2.3.2.8.51.1.1
An entry of gbondTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  GbondGroupEntry  

gbondGroupName 1.1.6321.1.2.3.2.8.51.1.1.1
An administratively assigned string, which may be used to identify bonding group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..31)  

gbondGroupPorts 1.1.6321.1.2.3.2.8.51.1.1.2
The set of ports which are currently assigned to the bonding group of specified group name. Byte 1: Reserved(chassis) Byte 2~3: Reserved(slot) Byte 4: Reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

gbondGroupUpRate 1.1.6321.1.2.3.2.8.51.1.1.4
The UP stream rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

gbondGroupDownRate 1.1.6321.1.2.3.2.8.51.1.1.5
The DOWN stream rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

gbondGroupRowStatus 1.1.6321.1.2.3.2.8.51.1.1.6
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

voipSipLineConfTable 1.1.6321.1.2.3.2.8.13.1
This table includes common attributes describing the VoIP line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipSipLineConfEntry

voipSipLineConfEntry 1.1.6321.1.2.3.2.8.13.1.1
An entry in voipSipLineConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipSipLineConfEntry  

voipSipLineConfSipProfile 1.1.6321.1.2.3.2.8.13.1.1.1
SIP profile name.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

voipSipLineConfSipCallSvcProfile 1.1.6321.1.2.3.2.8.13.1.1.2
SIP call service profile name.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

voipSipLineConfDspProfile 1.1.6321.1.2.3.2.8.13.1.1.3
DSP profile name.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

portOperations 1.1.6321.1.2.3.2.8.13.2
OBJECT IDENTIFIER    

voipPortTarget 1.1.6321.1.2.3.2.8.13.2.1
The managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chaises) Byte 2~3: 0,0 Reserved(slot) Byte 4: 0, Reserved Byte 5~11:Each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

voipPortOps 1.1.6321.1.2.3.2.8.13.2.2
The managed object is for VoIP configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: enable port BIT 2: disable port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipPortEnableStatus 1.1.6321.1.2.3.2.8.13.2.3
This read only entry is for showing current voip enable/disable status of each port. The status is encoded as: Byte 1: 0, Reserved Byte 2~3: 0,0 Reserved Byte 4: 0, Reserved Byte 5~11:Each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

voipPortTelTable 1.1.6321.1.2.3.2.8.13.3
This table includes VoIP tel for the port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipPortTelEntry

voipPortTelEntry 1.1.6321.1.2.3.2.8.13.3.1
An entry in voipPortTelTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipPortTelEntry  

voipPortTel 1.1.6321.1.2.3.2.8.13.3.1.1
VoIP's telephone number of the specified port.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

voipH248LineConfTable 1.1.6321.1.2.3.2.8.13.7
This table includes common attributes describing the VoIP line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipH248LineConfEntry

voipH248LineConfEntry 1.1.6321.1.2.3.2.8.13.7.1
An entry in voipH248LineConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipH248LineConfEntry  

voipH248LineConfMgName 1.1.6321.1.2.3.2.8.13.7.1.1
MG name.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

voipH248LineConfDspProfile 1.1.6321.1.2.3.2.8.13.7.1.2
DSP profile name.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

voipH248LineConfVBDProfile 1.1.6321.1.2.3.2.8.13.7.1.3
DSP profile name for Voice Band Data (FAX or Modem) mode.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

voipPortH248TerminationTable 1.1.6321.1.2.3.2.8.13.8
This table includes Termination name.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipPortH248TerminationEntry

voipPortH248TerminationEntry 1.1.6321.1.2.3.2.8.13.8.1
An entry in voipPortH248TerminationTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipPortH248TerminationEntry  

voipPortH248TermName 1.1.6321.1.2.3.2.8.13.8.1.1
Termination name of MG.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

voipPortGainTable 1.1.6321.1.2.3.2.8.13.6
This table includes Port Gain.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipPortGainEntry

voipPortGainEntry 1.1.6321.1.2.3.2.8.13.6.1
An entry in voipPortGainTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipPortGainEntry  

voipPortTXGain 1.1.6321.1.2.3.2.8.13.6.1.1
TX Gain of the port, -200~200 in unit of 0.1dB.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipPortRXGain 1.1.6321.1.2.3.2.8.13.6.1.2
RX Gain of the port, -200~200 in unit of 0.1dB.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

snrMgnTable 1.1.6321.1.2.3.2.8.15.1
A table containing the per port SNR Margin configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnrMarginEntry

snrMgnEntry 1.1.6321.1.2.3.2.8.15.1.1
An entry of snrMgnTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnrMarginEntry  

snrMgnMode 1.1.6321.1.2.3.2.8.15.1.1.1
Configure DSL SNR margin configuration mode of the specified ports. Profile: the SNR margin configuration comes from DSL profile. Line: the SNR margin configuration comes from line configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER profile(0), line(1)  

snrMgnUcTarget 1.1.6321.1.2.3.2.8.15.1.1.2
Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..310  

snrMgnUcMax 1.1.6321.1.2.3.2.8.15.1.1.3
Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..310  

snrMgnUcMin 1.1.6321.1.2.3.2.8.15.1.1.4
Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..310  

snrMgnUcDownshift 1.1.6321.1.2.3.2.8.15.1.1.5
Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..310  

snrMgnUcUpshift 1.1.6321.1.2.3.2.8.15.1.1.6
Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..310  

snrMgnUrTarget 1.1.6321.1.2.3.2.8.15.1.1.7
Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..310  

snrMgnUrMax 1.1.6321.1.2.3.2.8.15.1.1.8
Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..310  

snrMgnUrMin 1.1.6321.1.2.3.2.8.15.1.1.9
Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..310  

snrMgnUrDownshift 1.1.6321.1.2.3.2.8.15.1.1.10
Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..310  

snrMgnUrUpshift 1.1.6321.1.2.3.2.8.15.1.1.11
Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..310  

dslRateTable 1.1.6321.1.2.3.2.8.16.1
A table containing the per port DSL Rate configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DslRateEntry

dslRateEntry 1.1.6321.1.2.3.2.8.16.1.1
An entry of dslRateTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DslRateEntry  

dslRateMode 1.1.6321.1.2.3.2.8.16.1.1.1
Configure DSL Rate configuration mode of the specified ports. Profile: the DSL Rate configuration comes from DSL profile. Line: the DSL Rate configuration comes from line configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER profile(0), line(1)  

dslRateLatencyMode 1.1.6321.1.2.3.2.8.16.1.1.2
The latency mode is fast or interleave
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER interleave(1), fast(2)  

dslRateXtucMaxInterleaveDelay 1.1.6321.1.2.3.2.8.16.1.1.3
Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

dslRateXtucMaxTxRate 1.1.6321.1.2.3.2.8.16.1.1.4
Configured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

dslRateXtucMinTxRate 1.1.6321.1.2.3.2.8.16.1.1.5
Configured Minimum Transmit rate for `Fast' or `Interleave' channels, in bps
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

dslRateXturMaxInterleaveDelay 1.1.6321.1.2.3.2.8.16.1.1.6
Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

dslRateXturMaxTxRate 1.1.6321.1.2.3.2.8.16.1.1.7
Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

dslRateXturMinTxRate 1.1.6321.1.2.3.2.8.16.1.1.8
Configured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

voipProfile 1.1.6321.1.2.3.2.9.7
OBJECT IDENTIFIER    

sipProfile 1.1.6321.1.2.3.2.9.7.1
OBJECT IDENTIFIER    

maxNumOfSipProfiles 1.1.6321.1.2.3.2.9.7.1.1
The maximum number of SIP profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sipProfileTable 1.1.6321.1.2.3.2.9.7.1.2
This table includes SIP protocol related configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SipProfileEntry

sipProfileEntry 1.1.6321.1.2.3.2.9.7.1.2.1
An entry in sipProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SipProfileEntry  

sipProfileName 1.1.6321.1.2.3.2.9.7.1.2.1.1
This object is used by the SIP profile table in order to identify a row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

sipProfileSipSvr 1.1.6321.1.2.3.2.9.7.1.2.1.2
IP used for SIP registration or SIP domain name.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

sipProfileRegSvr 1.1.6321.1.2.3.2.9.7.1.2.1.3
Registration server IP or registration server domain name.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

sipProfileProxySvr 1.1.6321.1.2.3.2.9.7.1.2.1.4
Proxy server IP or proxy server doamin name.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

sipProfileSipPort 1.1.6321.1.2.3.2.9.7.1.2.1.5
SIP UA port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1025..65535  

sipProfileRegSvrPort 1.1.6321.1.2.3.2.9.7.1.2.1.6
Registration server port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1025..65535  

sipProfileProxySvrPort 1.1.6321.1.2.3.2.9.7.1.2.1.7
Proxy server port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1025..65535  

sipProfileUriType 1.1.6321.1.2.3.2.9.7.1.2.1.8
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER useSipUri(1), useTelUri(2)  

sipProfilePbit 1.1.6321.1.2.3.2.9.7.1.2.1.9
802.1p bit for SIP and RTP packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

sipProfileDscp 1.1.6321.1.2.3.2.9.7.1.2.1.10
DSCP for SIP and RTP packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..63  

sipProfileKeepAlive 1.1.6321.1.2.3.2.9.7.1.2.1.11
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

sipProfileSe 1.1.6321.1.2.3.2.9.7.1.2.1.12
Session expiration time in seconds.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 90..65535  

sipProfilePrack 1.1.6321.1.2.3.2.9.7.1.2.1.13
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

sipProfileRowStatus 1.1.6321.1.2.3.2.9.7.1.2.1.14
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sipProfileRegExpire 1.1.6321.1.2.3.2.9.7.1.2.1.15
Registration expiration time in seconds.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 120..2073600  

maxNumOfSipCallSvcProfiles 1.1.6321.1.2.3.2.9.7.1.3
The maximum number of SIP call service profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sipCallSvcProfileTable 1.1.6321.1.2.3.2.9.7.1.4
This table includes SIP call service related configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SipCallSvcProfileEntry

sipCallSvcProfileEntry 1.1.6321.1.2.3.2.9.7.1.4.1
An entry in sipCallSvcProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SipCallSvcProfileEntry  

sipCallSvcProfileName 1.1.6321.1.2.3.2.9.7.1.4.1.1
This object is used by the SIP call service profile table in order to identify a row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

sipCallSvcProfilePasswdOn 1.1.6321.1.2.3.2.9.7.1.4.1.2
Password is necessary or not for SIP registration.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

sipCallSvcProfilePasswd 1.1.6321.1.2.3.2.9.7.1.4.1.3
SIP registration password.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

sipCallSvcProfileNumberPlanOn 1.1.6321.1.2.3.2.9.7.1.4.1.4
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

sipCallSvcProfileNumberPlanCc 1.1.6321.1.2.3.2.9.7.1.4.1.5
Country code, only digit 0..9 are allowed.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

sipCallSvcProfileNumberPlanNdc 1.1.6321.1.2.3.2.9.7.1.4.1.6
National destination code, only digit 0..9 are allowed.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

sipCallSvcProfileNumberPlanTable 1.1.6321.1.2.3.2.9.7.1.4.1.7
Numbering plan table name.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

sipCallSvcProfileStateMask 1.1.6321.1.2.3.2.9.7.1.4.1.8
Bit 1 callforward : call forward(Not supported) Bit 2 callhold : call hold Bit 3 callwait : call waiting Bit 4 callreturn : call return(Not supported) Bit 5 calltransfer : call transfer Bit 6 clip : caller line identification presentation (Caller ID) Bit 7 clir : caller line identification restriction Bit 8 dnd : do not disturb Bit 9 conference : native 3-way conference
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

sipCallSvcProfileDtmf 1.1.6321.1.2.3.2.9.7.1.4.1.9
dtmf bypass : bypass DTMF tone dtmf rfc2833 : DTMF tone relay according to RFC2833 dtmf rfc2833like : DTMF tone relay by SIP INFO message, but RFC2833 payload dtmf sipinfo : DTMF tone relay by SIP INFO message
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER bypass(1), rfc2833(2), rfc2833like(3), sipinfo(4)  

sipCallSvcProfileFax 1.1.6321.1.2.3.2.9.7.1.4.1.10
fax g711 : FAX service pass through by ITU-T G.711 fax t38 : FAX service by ITU-T T.38
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER g711(1), t38(2)  

sipCallSvcProfileRowStatus 1.1.6321.1.2.3.2.9.7.1.4.1.11
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sipCallSvcProfileFlashType 1.1.6321.1.2.3.2.9.7.1.4.1.12
flash invite : will send SIP INVITE message while press flash button. flash bypass : flash event will be handled by current switch type specified in sipCallSvcProfileSwitchType. flash rfc2833 : flash event will send by RTP event (16) defined in RFC 2833. flash rfc2833like : flash event will send by SIP INFO message but RTP payload. flash sipinfo-1 : flash event will be sent by SIP INFO signal=16 message. flash sipinfo-2 : flash event will be sent by SIP INFO signal=hf message. flash sipinfo-3 : flash event will be sent by SIP INFO signal=hook-flash message. flash sipinfo-4 : flash event will be sent by SIP INFO plain text 'FLASH' message. flash sipinfo-5 : flash event will be sent by multiple SIP INFO signal messages and content of signal messages come from sipCallSvcProfileFlashInfo. flash sipinfo-6 : flash event will be sent by SIP INFO and payload is specified in sipCallSvcProfileFlashInfo.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER invite(1), rfc2833(2), rfc2833like(3), sipinfo-1(4), sipinfo-2(5), sipinfo-3(6), sipinfo-4(7), sipinfo-5(8), sipinfo-6(9), bypass(10)  

sipCallSvcProfileFlashInfo 1.1.6321.1.2.3.2.9.7.1.4.1.13
Strings carried in SIP INFO when specified in sipCallSvcProfileFlashType is sipinfo-5 and sipinfo-6.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

sipCallSvcProfileSoftSwitchType 1.1.6321.1.2.3.2.9.7.1.4.1.14
Softswitch type is configured to specify softswitch-dependent behavior, currently only flash event is softswitch-dependent and should follow the softswitch type setting. When configured the flash event to 'bypass', E5 will follow the softswitch type setting to report hook flash event.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER metaswitch(1), nortel(2)  

maxNumOfDspProfiles 1.1.6321.1.2.3.2.9.7.2
The maximum number of DSP profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dspProfileTable 1.1.6321.1.2.3.2.9.7.3
This table includes DSP related configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DspProfileEntry

dspProfileEntry 1.1.6321.1.2.3.2.9.7.3.1
An entry in dspProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DspProfileEntry  

dspProfileName 1.1.6321.1.2.3.2.9.7.3.1.1
This object is used by the DSP profile table in order to identify a row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

dspProfileCodec 1.1.6321.1.2.3.2.9.7.3.1.2
0x01: g711a 0x02: g711mu 0x03: g723 0x04: g726-16 0x05: g726-24 0x06: g726-32 0x07: g726-40 0x08: g729ab the value of dspProfileCodec is OCTET STRING, there are 8 Octets, each octect is specified as 0x01, 0x03, 0x02, 0x07,0x00, 0x00, 0x00, 0x00 (to specify different CODE in priority) specify as: g711a, g723, g711mu, g726-40
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

dspProfilePlayBufferMinDelay 1.1.6321.1.2.3.2.9.7.3.1.3
Play buffer minimum delay in milliseconds. It should be less than or equal to dspProfilePlayBufferMaxDelay.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 10..500  

dspProfilePlayBufferMaxDelay 1.1.6321.1.2.3.2.9.7.3.1.4
Play buffer maximum delay in milliseconds. It should be greater than or equal to dspProfilePlayBufferMinDelay.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 10..500  

dspProfileEchoTail 1.1.6321.1.2.3.2.9.7.3.1.5
Echo cancellation echo tail period in milliseconds.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER echotail8(1), echotail16(2), echotail32(3), echotail128(4)  

dspProfileRowStatus 1.1.6321.1.2.3.2.9.7.3.1.6
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

dspProfileG711Vpi 1.1.6321.1.2.3.2.9.7.3.1.7
Voice Packetization Interval(VPI) of codec G.711 in milliseconds. The values are 10, 20, 30, 40
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER g711x10ms(1), g711x20ms(2), g711x30ms(3), g711x40ms(4)  

dspProfileG723Vpi 1.1.6321.1.2.3.2.9.7.3.1.8
Voice Packetization Interval(VPI) of G.723 codec in milliseconds. The values are 30,60
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER g723x30ms(1), g723x60ms(2)  

dspProfileG726Vpi 1.1.6321.1.2.3.2.9.7.3.1.9
Voice Packetization Interval(VPI) of G.726 codec in milliseconds. The values are 10, 20, 30, 40
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER g726x10ms(1), g726x20ms(2), g726x30ms(3), g726x40ms(4)  

dspProfileG729Vpi 1.1.6321.1.2.3.2.9.7.3.1.10
Voice Packetization Interval(VPI) of G.729 codec in milliseconds. The values are 10, 20, 30, 40, 50, 60
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER g729x10ms(1), g729x20ms(2), g729x30ms(3), g729x40ms(4), g729x50ms(5), g729x60ms(6)  

h248Profile 1.1.6321.1.2.3.2.9.7.4
OBJECT IDENTIFIER    

maxNumOfH248Profiles 1.1.6321.1.2.3.2.9.7.4.1
The maximum number of H248 profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

h248ProfileTable 1.1.6321.1.2.3.2.9.7.4.2
This table includes H248 profile related configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H248ProfileEntry

h248ProfileEntry 1.1.6321.1.2.3.2.9.7.4.2.1
An entry in h248ProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H248ProfileEntry  

h248ProfileName 1.1.6321.1.2.3.2.9.7.4.2.1.1
This object is used by the H248 profile table in order to identify a row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

h248ProfileMgcSvr 1.1.6321.1.2.3.2.9.7.4.2.1.2
MGC IP or MGC doamin name.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

h248ProfileMgcPort 1.1.6321.1.2.3.2.9.7.4.2.1.3
MGC port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1025..65535  

h248ProfileMgc2On 1.1.6321.1.2.3.2.9.7.4.2.1.4
Secondary MGC on/off.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

h248ProfileMgc2Svr 1.1.6321.1.2.3.2.9.7.4.2.1.5
Secondary MGC IP or MGC doamin name. h248ProfileMgc2On needs to turn on if user want to set Secondary MGC IP or domain name.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

h248ProfileMgc2Port 1.1.6321.1.2.3.2.9.7.4.2.1.6
Secondary MGC port number. h248ProfileMgc2On needs to turn on if user want to set Secondary MGC port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1025..65535  

h248ProfileTransport 1.1.6321.1.2.3.2.9.7.4.2.1.7
Transport procotol used by the H.248 protocol stack.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER udp(1), tcp(2)  

h248ProfileEncode 1.1.6321.1.2.3.2.9.7.4.2.1.8
Encoding type used by the H.248 protocol stack
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER longtext(1), shorttext(2)  

h248ProfilePbit 1.1.6321.1.2.3.2.9.7.4.2.1.9
802.1p bit for H.248 packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

h248ProfileDscp 1.1.6321.1.2.3.2.9.7.4.2.1.10
DSCP for H.248 packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..63  

h248ProfileRowStatus 1.1.6321.1.2.3.2.9.7.4.2.1.11
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

h248ProfileVbd 1.1.6321.1.2.3.2.9.7.4.2.1.12
VBD mode support on/off
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

h248ProfileEphemeralPrefix 1.1.6321.1.2.3.2.9.7.4.2.1.14
Ephemeral Termination Prefix
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

h248ProfileSoftswitch 1.1.6321.1.2.3.2.9.7.4.2.1.15
Softswitch type
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER metaswitch(1), nortelCs1500(2), nortelCs2000(3)  

h248ProfileForceVer 1.1.6321.1.2.3.2.9.7.4.2.1.16
Force using H.248 version 1
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

h248ProfileStartRTPPort 1.1.6321.1.2.3.2.9.7.4.2.1.17
Start of RTP port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 4000..64000  

h248ProfileEndRTPPort 1.1.6321.1.2.3.2.9.7.4.2.1.18
End of RTP port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 5000..65000  

h248ProfileEphemeralStartNumber 1.1.6321.1.2.3.2.9.7.4.2.1.19
Ephemeral termination suffix start number, up to 15 digits.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

h248ProfileEphemeralSuffixLength 1.1.6321.1.2.3.2.9.7.4.2.1.20
Ephemeral termination suffix number length , padding zero at the front if not long enough.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..15  

h248ProfilePhysicalPrefix 1.1.6321.1.2.3.2.9.7.4.2.1.21
Physical Termination Prefix.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

h248ProfilePhysicalStartNumber 1.1.6321.1.2.3.2.9.7.4.2.1.22
Physical termination suffix start number, up to 15 digits.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

h248ProfilePhysicalSuffixLength 1.1.6321.1.2.3.2.9.7.4.2.1.23
Physical termination suffix number length , padding zero at the front if not long enough.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..15  

dscp 1.1.6321.1.2.3.2.10.10
OBJECT IDENTIFIER    

vlanIsolation 1.1.6321.1.2.3.2.10.12
OBJECT IDENTIFIER    

enetMtu 1.1.6321.1.2.3.2.10.13
OBJECT IDENTIFIER    

dhcp 1.1.6321.1.2.3.2.10.51
OBJECT IDENTIFIER    

macfilter 1.1.6321.1.2.3.2.10.53
OBJECT IDENTIFIER    

dhcpSnoop 1.1.6321.1.2.3.2.10.55
OBJECT IDENTIFIER    

acl 1.1.6321.1.2.3.2.10.56
OBJECT IDENTIFIER    

pppoeAgent 1.1.6321.1.2.3.2.10.57
OBJECT IDENTIFIER    

macff 1.1.6321.1.2.3.2.10.60
OBJECT IDENTIFIER    

dscpMappingTable 1.1.6321.1.2.3.2.10.10.1
The table contains DSCP mapping configuration for the adsl and ethernet ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DscpMappingEntry

dscpMappingEntry 1.1.6321.1.2.3.2.10.10.1.1
An entry of dscpMappingTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DscpMappingEntry  

dscpSrcCodePoint 1.1.6321.1.2.3.2.10.10.1.1.1
The DSCP source code point used for mapping.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dscpMapPriority 1.1.6321.1.2.3.2.10.10.1.1.3
The mapping p bits that will replace the source p bits in the incoming packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

dscpPortTable 1.1.6321.1.2.3.2.10.10.2
The table contains DSCP mapping configuration for the adsl and ethernet ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DscpPortEntry

dscpPortEntry 1.1.6321.1.2.3.2.10.10.2.1
An entry of dscpPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DscpPortEntry  

dscpStatusEnable 1.1.6321.1.2.3.2.10.10.2.1.1
The DSCP port status.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vlanIsolationTable 1.1.6321.1.2.3.2.10.12.1
A table contains configuration of isolated VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VlanIsolationEntry

vlanIsolationEntry 1.1.6321.1.2.3.2.10.12.1.1
An entry of vlanIsolationTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanIsolationEntry  

vlanIsolationRowStatus 1.1.6321.1.2.3.2.10.12.1.1.1
Row status of the table used to create/delete an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

enetMtuEntry 1.1.6321.1.2.3.2.10.13.1
Sets the MTU size for layer 2 frame, size from 1526 to 1532, default value is 1526.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dhcpRelay82Table 1.1.6321.1.2.3.2.10.51.2
A table that contains DHCP Relay configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpRelay82Entry

dhcpRelay82Entry 1.1.6321.1.2.3.2.10.51.2.1
The entry of DHCP Relay table.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpRelay82Entry  

dhcpRelay82PrimaryServer 1.1.6321.1.2.3.2.10.51.2.1.1
The IP address of the DHCP Relay primary server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dhcpRelay82SecondaryServer 1.1.6321.1.2.3.2.10.51.2.1.2
The IP address of the DHCP Relay secondary server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dhcpRelay82ActiveServer 1.1.6321.1.2.3.2.10.51.2.1.3
The current active DHCP Relay server.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), third(3), fourth(4), fifth(5)  

dhcpRelay82Enable 1.1.6321.1.2.3.2.10.51.2.1.4
Enable/disable DHCP relay and Option82 function.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dhcpRelay82Info 1.1.6321.1.2.3.2.10.51.2.1.5
User specific Option82 information.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..23)  

dhcpRelay82RelayMode 1.1.6321.1.2.3.2.10.51.2.1.6
DHCP relay mode.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER auto(1), all(2)  

dhcpRelay82Suboption2Enable 1.1.6321.1.2.3.2.10.51.2.1.8
Enable/disable Option 82 sub-option 2.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dhcpRelay82Suboption2Info 1.1.6321.1.2.3.2.10.51.2.1.9
User specified information for Option 82 sub-option 2.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

dhcpRelay82EntryEnable 1.1.6321.1.2.3.2.10.51.2.1.10
Enable/disable DHCP Relay
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER auto(1), all(2), disable(3)  

dhcpRelay82EntryOptionMode 1.1.6321.1.2.3.2.10.51.2.1.11
Option82 format.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER private(1), tr101(2)  

dhcpRelay82VlanIp 1.1.6321.1.2.3.2.10.51.2.1.12
The IP address of the DHCP Relay interface for this VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dhcpRelay82VlanMask 1.1.6321.1.2.3.2.10.51.2.1.13
The network mask of the DHCP Relay interface for this VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dhcpRelay82VlanGateway 1.1.6321.1.2.3.2.10.51.2.1.14
The gateway of the DHCP Relay interface for this VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dhcpRelay82ThirdServer 1.1.6321.1.2.3.2.10.51.2.1.15
The IP address of the DHCP Relay third server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dhcpRelay82FourthServer 1.1.6321.1.2.3.2.10.51.2.1.16
The IP address of the DHCP Relay fourth server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dhcpRelay82FifthServer 1.1.6321.1.2.3.2.10.51.2.1.17
The IP address of the DHCP Relay fifth server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dhcpRelay82ServerVid 1.1.6321.1.2.3.2.10.51.2.1.18
The VID of the DHCP Relay server for this VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dhcpRelayTest 1.1.6321.1.2.3.2.10.51.8
OBJECT IDENTIFIER    

dhcpRelayTestVid 1.1.6321.1.2.3.2.10.51.8.1
Setting the VID of the test server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dhcpRelayTestIp 1.1.6321.1.2.3.2.10.51.8.2
Setting the IP of the test server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dhcpRelayTestOps 1.1.6321.1.2.3.2.10.51.8.3
Set the object to 1 to test DHCP server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dhcpRelayTestStatus 1.1.6321.1.2.3.2.10.51.8.4
Display testing server status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

dhcpRelayArp 1.1.6321.1.2.3.2.10.51.9
OBJECT IDENTIFIER    

dhcpRelayArpShowTable 1.1.6321.1.2.3.2.10.51.9.1
The table displays DHCP ARP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpRelayArpShowEntry

dhcpRelayArpShowEntry 1.1.6321.1.2.3.2.10.51.9.1.1
An entry of dhcpRelayArpShowTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpRelayArpShowEntry  

dhcpRelayArpShowVid 1.1.6321.1.2.3.2.10.51.9.1.1.1
Display the VID of the DHCP ARP entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dhcpRelayArpShowIp 1.1.6321.1.2.3.2.10.51.9.1.1.2
Display the IP of the DHCP ARP entry.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpRelayArpShowMac 1.1.6321.1.2.3.2.10.51.9.1.1.3
Display the MAC of the DHCP ARP entry.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

dhcpRelayArpFlushOps 1.1.6321.1.2.3.2.10.51.9.2
Set the object to 1 to start flushing.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

macFilterPortTable 1.1.6321.1.2.3.2.10.53.1
This table includes the status of mac filtering for each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFilterPortEntry

macFilterPortEntry 1.1.6321.1.2.3.2.10.53.1.1
An entry in macFilterPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFilterPortEntry  

macFilterPortEnable 1.1.6321.1.2.3.2.10.53.1.1.1
Enable/disable MAC filtering for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enableMacFilter(1), enableMacCount(2), disable(4), enableMacFilterAndMacCount(5)  

macFilterPortMacCount 1.1.6321.1.2.3.2.10.53.1.1.2
The total number of MAC addresses allowed for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..128  

macFilterPortFilterMode 1.1.6321.1.2.3.2.10.53.1.1.3
The mac filter mode (accept or deny) for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER accept(1), deny(2)  

maxNumOfMacFiltersInSystem 1.1.6321.1.2.3.2.10.53.2
The max number of mac filters supported in the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxNumOfMacFiltersPerPort 1.1.6321.1.2.3.2.10.53.3
The max number of mac filters supported per port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

currNumOfMacFiltersInSystem 1.1.6321.1.2.3.2.10.53.4
The current number of mac filters in the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFilterTable 1.1.6321.1.2.3.2.10.53.5
A table that contains the mac filter addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFilterEntry

macFilterEntry 1.1.6321.1.2.3.2.10.53.5.1
The entry of macFilterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFilterEntry  

macFilterAddr 1.1.6321.1.2.3.2.10.53.5.1.1
The mac address which can pass through or be rejected from the port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

macFilterRowStatus 1.1.6321.1.2.3.2.10.53.5.1.2
The row status of the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

macfilterBatchSet 1.1.6321.1.2.3.2.10.53.6
OBJECT IDENTIFIER    

macfilterTarget 1.1.6321.1.2.3.2.10.53.6.1
This managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chassis) Byte 2~3: 0, Reserved(slot) Byte 4: 0, reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

macfilterOps 1.1.6321.1.2.3.2.10.53.6.2
The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: enable mac filter BIT 2: enable mac count filter BIT 3: disable mac filter BIT 4: set mac count BIT 5: disable mac count filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

macFilterMacCountForBatchSet 1.1.6321.1.2.3.2.10.53.6.3
The total number of MAC addresses allowed for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..128  

ouiFilterTableOld 1.1.6321.1.2.3.2.10.53.7
A table that contains the OUI filter addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OuiFilterEntryOld

ouiFilterEntryOld 1.1.6321.1.2.3.2.10.53.7.1
The entry of ouiFilterTableOld.
Status: current Access: not-accessible
OBJECT-TYPE    
  OuiFilterEntryOld  

ouiFilterAddrOld 1.1.6321.1.2.3.2.10.53.7.1.1
The first three bytes of the mac address which can pass through or be rejected from the port.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ouiFilterRowStatusOld 1.1.6321.1.2.3.2.10.53.7.1.2
The row status of the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

maxNumOfOuiFiltersPerPort 1.1.6321.1.2.3.2.10.53.8
The max number of OUI filters supported per port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ouiFilterPortTable 1.1.6321.1.2.3.2.10.53.9
This table includes the status of oui filtering for each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OuiFilterPortEntry

ouiFilterPortEntry 1.1.6321.1.2.3.2.10.53.9.1
An entry in macFilterPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  OuiFilterPortEntry  

ouiFilterPortEnable 1.1.6321.1.2.3.2.10.53.9.1.1
Enable/disable oui filtering for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enableOuiFilter(1), disable(2)  

ouiFilterPortFilterMode 1.1.6321.1.2.3.2.10.53.9.1.2
The oui filter mode (accept or deny) for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER accept(1), deny(2)  

maxNumOfOuiFiltersInSystem 1.1.6321.1.2.3.2.10.53.10
The max number of OUI filters supported in system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxNumOfOuiFiltersPerVlan 1.1.6321.1.2.3.2.10.53.11
The max number of OUI filters supported per vlan.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ouiFilterTable 1.1.6321.1.2.3.2.10.53.12
A table that contains the OUI filter addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OuiFilterEntry

ouiFilterEntry 1.1.6321.1.2.3.2.10.53.12.1
The entry of ouiFilterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  OuiFilterEntry  

ouiFilterAddr 1.1.6321.1.2.3.2.10.53.12.1.1
The first three bytes of the mac address which can pass through or be rejected from the vlan.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ouiFilterRowStatus 1.1.6321.1.2.3.2.10.53.12.1.2
The row status of the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ouiFilterVlanTable 1.1.6321.1.2.3.2.10.53.13
This table includes the status of oui filtering for each configured VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OuiFilterVlanEntry

ouiFilterVlanEntry 1.1.6321.1.2.3.2.10.53.13.1
An entry in ouiFilterVlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  OuiFilterVlanEntry  

ouiFilterVlanEnable 1.1.6321.1.2.3.2.10.53.13.1.1
Enable/disable oui filtering for the VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enableOuiFilter(1), disable(2)  

ouiFilterVlanFilterMode 1.1.6321.1.2.3.2.10.53.13.1.2
The oui filter mode (accept or deny) for the VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER accept(1), deny(2)  

dhcpSnoopPortTable 1.1.6321.1.2.3.2.10.55.1
This table includes DHCP snooping enable/disable for each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpSnoopPortEntry

dhcpSnoopPortEntry 1.1.6321.1.2.3.2.10.55.1.1
An entry of dhcpSnoopPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpSnoopPortEntry  

dhcpSnoopEnable 1.1.6321.1.2.3.2.10.55.1.1.1
Enable/disable DHCP snooping for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dhcpSnoopMaxcnt 1.1.6321.1.2.3.2.10.55.1.1.2
Set the max entries of the DHCP ARP table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dhcpSnoopSmacverifyEnable 1.1.6321.1.2.3.2.10.55.1.1.3
Enable/disable DHCP source MAC verify for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dhcpSnoopTarget 1.1.6321.1.2.3.2.10.55.2
This managed object is used for identify the target on which the operation should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

dhcpSnoopOps 1.1.6321.1.2.3.2.10.55.3
The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: DHCP snooping table flush.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dhcpStaticTable 1.1.6321.1.2.3.2.10.55.4
This table defines DHCP static IP addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpStaticEntry

dhcpStaticEntry 1.1.6321.1.2.3.2.10.55.4.1
An entry of dhcpStaticTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpStaticEntry  

dhcpStaticIpAddr 1.1.6321.1.2.3.2.10.55.4.1.1
The IP address which can pass through the port.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpStaticRowStatus 1.1.6321.1.2.3.2.10.55.4.1.2
Row status of the table entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

maxNumOfDhcpStaticIp 1.1.6321.1.2.3.2.10.55.5
The maximum number of DHCP static IP addresses which can be created for a port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dhcpSnoopMaxcntMode 1.1.6321.1.2.3.2.10.55.6
When DHCP snooping table is full, new DHCP lease will replace first one in option 0 or will be dropped in option 1.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER replace(1), drop(2)  

aclSetTable 1.1.6321.1.2.3.2.10.56.1
aclsetTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AclSetEntry

aclSetEntry 1.1.6321.1.2.3.2.10.56.1.1
An entry of aclSetTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AclSetEntry  

aclSetVpi 1.1.6321.1.2.3.2.10.56.1.1.1
VPI value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

aclSetVci 1.1.6321.1.2.3.2.10.56.1.1.2
VCI value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

aclSetProfileName 1.1.6321.1.2.3.2.10.56.1.1.3
ACL Profile name
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

aclSetRowStatus 1.1.6321.1.2.3.2.10.56.1.1.4
RowStatus of aclSetEntry
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

aclProfileTable 1.1.6321.1.2.3.2.10.56.2
aclProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AclProfileEntry

aclProfileEntry 1.1.6321.1.2.3.2.10.56.2.1
An entry of aclProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AclProfileEntry  

aclProfileRuleName 1.1.6321.1.2.3.2.10.56.2.1.1
Profile rule name
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

aclProfileRuleNumber 1.1.6321.1.2.3.2.10.56.2.1.2
The managed object is for acl profile rule configuration. etype vlan (1), etype smac (2), etype dmac (3), vlan smac (4), vlan dmac (5), smac dmac (6), vlan priority (7), etype (8), vlan (9), smac (10), dmac (11), priority (12), protocol (13), {srcip /{|dstip /{|tos {|srcport {|dstport }}}}} (14)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

aclProfileActionNumber 1.1.6321.1.2.3.2.10.56.2.1.3
Profile action number. Bit 1: rate Bit 2: rvlan Bit 3: rpri Bit 4: deny Bit 1, Bit 2 & Bit 3 can multiple selection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

aclProfileRuleParamMask 1.1.6321.1.2.3.2.10.56.2.1.4
Profile rule parameter mask. BIT 1: srcip / BIT 2: dstip / BIT 3: tos BIT 4: srcport BIT 5: dstport
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

aclProfileRuleEtype 1.1.6321.1.2.3.2.10.56.2.1.5
Profile rule etype
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

aclProfileRuleVid 1.1.6321.1.2.3.2.10.56.2.1.6
Profile rule vid
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

aclProfileRuleSmac 1.1.6321.1.2.3.2.10.56.2.1.7
Profile rule source MAC
Status: current Access: read-write
OBJECT-TYPE    
  PhysAddress  

aclProfileRuleDmac 1.1.6321.1.2.3.2.10.56.2.1.8
Profile rule destination MAC
Status: current Access: read-write
OBJECT-TYPE    
  PhysAddress  

aclProfileRulePriority 1.1.6321.1.2.3.2.10.56.2.1.9
Profile rule priority
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

aclProfileRuleProtocol 1.1.6321.1.2.3.2.10.56.2.1.10
Profile rule protocol. icmp(1),igmp(2),ip(4),tcp(6), udp(17),gre(47),ospf(89), other ptype
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

aclProfileRuleSrcIP 1.1.6321.1.2.3.2.10.56.2.1.11
Profile rule source IP
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

aclProfileRuleSrcIPMask 1.1.6321.1.2.3.2.10.56.2.1.12
The subnet mask of source IP mask
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..32  

aclProfileRuleDestIP 1.1.6321.1.2.3.2.10.56.2.1.13
Profile rule source IP
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

aclProfileRuleDestIPMask 1.1.6321.1.2.3.2.10.56.2.1.14
The subnet mask of dest IP mask
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..32  

aclProfileRuleStartTos 1.1.6321.1.2.3.2.10.56.2.1.15
Profile rule start type of service
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

aclProfileRuleEndTos 1.1.6321.1.2.3.2.10.56.2.1.16
Profile rule end type of service
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

aclProfileRuleSrcStartPort 1.1.6321.1.2.3.2.10.56.2.1.17
Profile rule source start port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

aclProfileRuleSrcEndPort 1.1.6321.1.2.3.2.10.56.2.1.18
Profile rule source end port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

aclProfileRuleDestStartPort 1.1.6321.1.2.3.2.10.56.2.1.19
Profile rule destination start port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

aclProfileRuleDestEndPort 1.1.6321.1.2.3.2.10.56.2.1.20
Profile rule destination end port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

aclProfileActionRate 1.1.6321.1.2.3.2.10.56.2.1.21
Profile action to replace to this rate
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

aclProfileActionrvlan 1.1.6321.1.2.3.2.10.56.2.1.22
Profile action to replace to this vlan
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

aclProfileActionrpri 1.1.6321.1.2.3.2.10.56.2.1.23
Profile action to replace to this priority
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

aclProfileRowStatus 1.1.6321.1.2.3.2.10.56.2.1.24
The row status of the entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

pppoeAgentTable 1.1.6321.1.2.3.2.10.57.1
A table that contains PPPoE DHCP Relay configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PppoeAgentEntry

pppoeAgentEntry 1.1.6321.1.2.3.2.10.57.1.1
An entry of pppoeAgentTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PppoeAgentEntry  

pppoeAgentEnable 1.1.6321.1.2.3.2.10.57.1.1.1
Enable/disable DHCP relay and Option82 function.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

pppoeAgentInfo 1.1.6321.1.2.3.2.10.57.1.1.2
User specific Option82 information.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..23)  

pppoeAgentRowStatus 1.1.6321.1.2.3.2.10.57.1.1.3
Row status of the table entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pppoeAgentOptionMode 1.1.6321.1.2.3.2.10.57.1.1.4
Option82 format.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER private(1), tr101(2)  

maxNumOfPppoeDhcpRelay82Conf 1.1.6321.1.2.3.2.10.57.2
The maximum number of rows that can be created in pppoeAgentTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFfTable 1.1.6321.1.2.3.2.10.60.1
A table that contains MAC Force Forwarding configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFfEntry

macFfEntry 1.1.6321.1.2.3.2.10.60.1.1
An entry of macFfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFfEntry  

macFfIndex 1.1.6321.1.2.3.2.10.60.1.1.1
Index of the MACFF.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFfVid 1.1.6321.1.2.3.2.10.60.1.1.2
The VLAN-ID refering to this AR/AS.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

macFfArIP 1.1.6321.1.2.3.2.10.60.1.1.3
IP of this AR/AS
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

macFfSrcIP 1.1.6321.1.2.3.2.10.60.1.1.4
The source IP address of the MACFF.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

macFfSrcMask 1.1.6321.1.2.3.2.10.60.1.1.5
The subnet mask of source IP mask.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

macFfRowStatus 1.1.6321.1.2.3.2.10.60.1.1.6
The row status of the MacFfEntry entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

macFfArpFlush 1.1.6321.1.2.3.2.10.60.3
Set the object to 1 to flush mac table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

maxNumOfMacFfVlanInSystem 1.1.6321.1.2.3.2.10.60.4
The max number of macff Vlans supported in the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFfVlanTable 1.1.6321.1.2.3.2.10.60.5
A table that contains MAC Force Forwarding Vlan configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFfVlanEntry

macFfVlanEntry 1.1.6321.1.2.3.2.10.60.5.1
An entry of macFfVlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFfVlanEntry  

macFfVlanRowstatus 1.1.6321.1.2.3.2.10.60.5.1.1
Row status of the table used to create/delete an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

macFfVlanUnknownUnicast 1.1.6321.1.2.3.2.10.60.5.1.2
Setting downstream unknown uni-cast packet on macff vlan to flooding or dropping.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER flood(1), drop(2)  

macFfStaticIPTable 1.1.6321.1.2.3.2.10.60.6
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFfStaticIPEntry

macFfStaticIPEntry 1.1.6321.1.2.3.2.10.60.6.1
An entry of macFfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFfStaticIPEntry  

macFfStaticIPPort 1.1.6321.1.2.3.2.10.60.6.1.1
The port number, 1 ~ 48.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFfStaticIPVid 1.1.6321.1.2.3.2.10.60.6.1.2
VLAN ID of the IP range, 1 ~ 4094, the vid should be enable the MACFF function first.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFfstaticIP 1.1.6321.1.2.3.2.10.60.6.1.3
The specified IP range.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

macFfStaticIPMask 1.1.6321.1.2.3.2.10.60.6.1.4
Mask_bits is 24 .. 32.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFfStaticIPRowStatus 1.1.6321.1.2.3.2.10.60.6.1.5
The row status used to configure the table entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

accessCtrl 1.1.6321.1.2.3.2.11.5
OBJECT IDENTIFIER    

extAlarm 1.1.6321.1.2.3.2.11.8
OBJECT IDENTIFIER    

user 1.1.6321.1.2.3.2.11.9
OBJECT IDENTIFIER    

usbCastCtrl 1.1.6321.1.2.3.2.11.10
OBJECT IDENTIFIER    

dsbCastCtrl 1.1.6321.1.2.3.2.11.11
OBJECT IDENTIFIER    

stdioTimeout 1.1.6321.1.2.3.2.11.12
Set the CLI/TELNET/WEB Session timeout, 0, or 1~300 minutes, 0 => disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..300  

isConfigChanged 1.1.6321.1.2.3.2.11.13
If system configuration has been changed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

fwUpgrade 1.1.6321.1.2.3.2.11.14
OBJECT IDENTIFIER    

delayedReboot 1.1.6321.1.2.3.2.11.15
OBJECT IDENTIFIER    

securedClientTable 1.1.6321.1.2.3.2.11.5.2
A table that contains information about secured clients.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SecuredClientEntry

securedClientEntry 1.1.6321.1.2.3.2.11.5.2.1
A list of secured client entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SecuredClientEntry  

securedClientIndex 1.1.6321.1.2.3.2.11.5.2.1.1
The index of the entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

securedClientStartIp 1.1.6321.1.2.3.2.11.5.2.1.2
The starting IP address of the secured client set.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

securedClientEndIp 1.1.6321.1.2.3.2.11.5.2.1.3
The ending IP address of the secured client set.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

securedClientService 1.1.6321.1.2.3.2.11.5.2.1.4
Each bit corresponds to a service. The bit is set to 1 if the service is enabled, and set to 0 if the service is disabled. The various bit positions are: BIT 1: telnet BIT 2: ftp BIT 3: web BIT 4: icmp BIT 5: not support BIT 6: snmp.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

securedClientEnable 1.1.6321.1.2.3.2.11.5.2.1.5
Enable/disable the entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

extAlarmTable 1.1.6321.1.2.3.2.11.8.1
A table that contains external alarm information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ExtAlarmEntry

extAlarmEntry 1.1.6321.1.2.3.2.11.8.1.1
The entry of external alarm table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ExtAlarmEntry  

extAlarmIndex 1.1.6321.1.2.3.2.11.8.1.1.1
The index of the entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

extAlarmname 1.1.6321.1.2.3.2.11.8.1.1.2
The external alarm name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

extAlarmstatus 1.1.6321.1.2.3.2.11.8.1.1.3
Dispaly 'Normal' or 'Alarm' string
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

extAlarmTriggeredMode 1.1.6321.1.2.3.2.11.8.1.1.4
The external alarm triggered mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER closeAlarm(1), openAlarm(2)  

userAuthMode 1.1.6321.1.2.3.2.11.9.1
User authentication procsssing mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER local(1), radius(2), localThenRadius(3)  

userAuthServerIp 1.1.6321.1.2.3.2.11.9.2
The IP address of the authentication server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

userAuthServerPort 1.1.6321.1.2.3.2.11.9.3
The port of the authentication server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

userAuthServerSecret 1.1.6321.1.2.3.2.11.9.4
The secret between the authentication server and the NE for authentication process.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

userTable 1.1.6321.1.2.3.2.11.9.5
A table that contains user information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UserEntry

userEntry 1.1.6321.1.2.3.2.11.9.5.1
An entry of userTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UserEntry  

userName 1.1.6321.1.2.3.2.11.9.5.1.1
The user name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

userPassword 1.1.6321.1.2.3.2.11.9.5.1.2
The user password.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

userPriviledge 1.1.6321.1.2.3.2.11.9.5.1.3
The user priviledge to decide what operation the user can and cannot do.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER high(1), middle(2), low(3)  

userRowStatus 1.1.6321.1.2.3.2.11.9.5.1.4
The row status used to create or delete a user.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

userAuthDefaultPriviledge 1.1.6321.1.2.3.2.11.9.6
The user default priviledge to be assigned when radius authentication succeds but no user priviledge information(radius service-type) is provided.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER high(1), middle(2), low(3), deny(4)  

usBcastCtrlEnable 1.1.6321.1.2.3.2.11.10.1
Enable/disable upstream broadcast control.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

usBcastCtrlRate 1.1.6321.1.2.3.2.11.10.2
32~49984 in step of 32kbps
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dsBcastCtrlEnable 1.1.6321.1.2.3.2.11.11.1
Enable/disable downstream broadcast control.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dsBcastCtrlRate 1.1.6321.1.2.3.2.11.11.2
32~1000000 in step of 32 kbps
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

fwUpgradeVersion 1.1.6321.1.2.3.2.11.14.1
Configure the target firmware version that will be upgraded.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

fwUpgradeCheck 1.1.6321.1.2.3.2.11.14.2
Enable/disable firmware upgrade version checking feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fwUpgradeStatus 1.1.6321.1.2.3.2.11.14.3
Display current firmware upgrade status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

delayedRebootTimer 1.1.6321.1.2.3.2.11.15.1
5~1800 secs, 0: reboot immediately.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

delayedRebootRemainingTime 1.1.6321.1.2.3.2.11.15.2
Display the remaining time of scheduled reboot.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

delayedRebootCancel 1.1.6321.1.2.3.2.11.15.3
cancel the scheduled reboot.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER cancel(1)  

dhcpStats 1.1.6321.1.2.3.2.13.11
OBJECT IDENTIFIER    

paepvcStats 1.1.6321.1.2.3.2.13.12
OBJECT IDENTIFIER    

macStats 1.1.6321.1.2.3.2.13.13
OBJECT IDENTIFIER    

ipbpvcStats 1.1.6321.1.2.3.2.13.14
OBJECT IDENTIFIER    

voipStats 1.1.6321.1.2.3.2.13.15
OBJECT IDENTIFIER    

macffStats 1.1.6321.1.2.3.2.13.16
OBJECT IDENTIFIER    

enetStats 1.1.6321.1.2.3.2.13.17
OBJECT IDENTIFIER    

adslStats 1.1.6321.1.2.3.2.13.18
OBJECT IDENTIFIER    

igmpQueryCntTotal 1.1.6321.1.2.3.2.13.1
The total number of IGMP query messages received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpReportCntTotal 1.1.6321.1.2.3.2.13.2
The total number of IGMP report messages received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpLeaveCntTotal 1.1.6321.1.2.3.2.13.3
The total number of IGMP leave messages received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpNumOfActiveGroups 1.1.6321.1.2.3.2.13.4
The total number of IGMP learned groups.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpGroupTable 1.1.6321.1.2.3.2.13.5
This table includes igmp group information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpGroupEntry

igmpGroupEntry 1.1.6321.1.2.3.2.13.5.1
An entry in igmpGroupTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpGroupEntry  

igmpGroupIp 1.1.6321.1.2.3.2.13.5.1.1
igmp group IP
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

igmpGroupvid 1.1.6321.1.2.3.2.13.5.1.2
vlan id
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpGroupnumberOfMembers 1.1.6321.1.2.3.2.13.5.1.3
number Of Members
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpGroupMemberPorts 1.1.6321.1.2.3.2.13.5.1.4
Group Member Ports
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

igmpGroupPortTable 1.1.6321.1.2.3.2.13.6
This table includes igmp Group port information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpGroupPortEntry

igmpGroupPortEntry 1.1.6321.1.2.3.2.13.6.1
An entry in igmpGroupPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpGroupPortEntry  

igmpGroupPortIp 1.1.6321.1.2.3.2.13.6.1.1
Igmp Group IP
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

igmpGroupPortvid 1.1.6321.1.2.3.2.13.6.1.2
Igmp Group vid
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpGroupV2Table 1.1.6321.1.2.3.2.13.7
A table that displays IGMP learned group member information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpGroupV2Entry

igmpGroupV2Entry 1.1.6321.1.2.3.2.13.7.1
An entry of igmpGroupV2Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpGroupV2Entry  

igmpGroupV2Vid 1.1.6321.1.2.3.2.13.7.1.1
The IGMP group VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

igmpGroupV2Ip 1.1.6321.1.2.3.2.13.7.1.2
The multicast IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

igmpGroupV2NumOfMembers 1.1.6321.1.2.3.2.13.7.1.3
The number of member ports in the group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpGroupV2MemberPorts 1.1.6321.1.2.3.2.13.7.1.4
The member port list of the group.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

igmpGroupPortV2Table 1.1.6321.1.2.3.2.13.8
A table that displays IGMP joined groups in this port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpGroupPortV2Entry

igmpGroupPortV2Entry 1.1.6321.1.2.3.2.13.8.1
An entry of igmpGroupPortV2Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpGroupPortV2Entry  

igmpGroupPortV2Vid 1.1.6321.1.2.3.2.13.8.1.1
The IGMP group VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

igmpGroupPortV2Ip 1.1.6321.1.2.3.2.13.8.1.2
The multicast IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

igmpGroupPortV2SourceIp 1.1.6321.1.2.3.2.13.8.1.3
The source IP address that joins the IGMP group.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

igmpPortCtrlPduTable 1.1.6321.1.2.3.2.13.9
A table that displays IGMP related counter values in this port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpPortCtrlPduEntry

igmpPortCtrlPduEntry 1.1.6321.1.2.3.2.13.9.1
An entry of igmpPortCtrlPduTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpPortCtrlPduEntry  

igmpPortCtrlPduQueryCnt 1.1.6321.1.2.3.2.13.9.1.1
The total number of IGMP query messages received in this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpPortCtrlPduReportCnt 1.1.6321.1.2.3.2.13.9.1.2
The total number of IGMP report messages received in this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpPortCtrlPduLeaveCnt 1.1.6321.1.2.3.2.13.9.1.3
The total number of IGMP leave messages received in this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpPortNumOfActiveGroups 1.1.6321.1.2.3.2.13.9.1.4
The total number of active IGMP groups in this port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpPortCtrlAuditLeaveCnt 1.1.6321.1.2.3.2.13.9.1.5
The total number of groups left by audit query.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dhcpSnoopIpTable 1.1.6321.1.2.3.2.13.11.1
This table shows the IP addresses and netmasks offered by the DHCP server.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpSnoopIpEntry

dhcpSnoopIpEntry 1.1.6321.1.2.3.2.13.11.1.1
An entry of dhcpSnoopIpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpSnoopIpEntry  

dhcpSnoopIp 1.1.6321.1.2.3.2.13.11.1.1.1
The snooped IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpSnoopMac 1.1.6321.1.2.3.2.13.11.1.1.2
The snooped MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

dhcpSnoopVid 1.1.6321.1.2.3.2.13.11.1.1.3
The snooped VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

dhcpSnoopMask 1.1.6321.1.2.3.2.13.11.1.1.4
The snooped IP mask
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dhcpSnoopGateway 1.1.6321.1.2.3.2.13.11.1.1.5
The snooped Gateway.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpSnoopRouteMap 1.1.6321.1.2.3.2.13.11.1.1.6
The refrence bit map of the dhcp route
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

dhcpSnoopCounterTable 1.1.6321.1.2.3.2.13.11.2
This table shows the DHCP statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpSnoopCounterEntry

dhcpSnoopCounterEntry 1.1.6321.1.2.3.2.13.11.2.1
An entry of dhcpSnoopCounterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpSnoopCounterEntry  

dhcpDiscovery 1.1.6321.1.2.3.2.13.11.2.1.1
The total number of received DHCP server discovery packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpOffer 1.1.6321.1.2.3.2.13.11.2.1.2
The total number of received DHCP server offer packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpRequest 1.1.6321.1.2.3.2.13.11.2.1.3
The total number of received DHCP IP request packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpAck 1.1.6321.1.2.3.2.13.11.2.1.4
The total number of received DHCP IP acknowledge packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpAckBySnoopFull 1.1.6321.1.2.3.2.13.11.2.1.5
The total number of received DHCP IP acknowledge packets that replace the oldest snooping entry in snooping table due to table full.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpRouteTable 1.1.6321.1.2.3.2.13.11.3
A table that contains dhcp route information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpRouteEntry

dhcpRouteEntry 1.1.6321.1.2.3.2.13.11.3.1
An entry of dhcpRouteTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpRouteEntry  

dhcpRouteIndex 1.1.6321.1.2.3.2.13.11.3.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..24  

dhcpRouteVid 1.1.6321.1.2.3.2.13.11.3.1.2
The VLAN-ID refering to this dhcp route.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

dhcpRouteIP 1.1.6321.1.2.3.2.13.11.3.1.3
IP of this dhcp route
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpRouteMask 1.1.6321.1.2.3.2.13.11.3.1.4
The subnet mask of source IP mask.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dhcpRouteGwIP 1.1.6321.1.2.3.2.13.11.3.1.5
The gateway IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

paepvcSessionTable 1.1.6321.1.2.3.2.13.12.1
This table shows the paepvc session statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PaepvcSessionEntry

paepvcSessionEntry 1.1.6321.1.2.3.2.13.12.1.1
An entry of paepvcSessionTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PaepvcSessionEntry  

paepvcSessionVpi 1.1.6321.1.2.3.2.13.12.1.1.1
The PAEPVC VPI.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

paepvcSessionVci 1.1.6321.1.2.3.2.13.12.1.1.2
The PAEPVC VCI.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

paepvcSessionState 1.1.6321.1.2.3.2.13.12.1.1.3
The PAEPVC status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(1), pppoe(2), ppp(3), up(4)  

paepvcSessionId 1.1.6321.1.2.3.2.13.12.1.1.4
The PAEPVC session ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

paepvcSessionUptime 1.1.6321.1.2.3.2.13.12.1.1.5
The PAEPVC session uptime.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcSessionacname 1.1.6321.1.2.3.2.13.12.1.1.6
Access concentrator name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

paepvcSessionsrvcname 1.1.6321.1.2.3.2.13.12.1.1.7
Service name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

paepvcCountTable 1.1.6321.1.2.3.2.13.12.2
This table shows the paepvc counters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PaepvcCountEntry

paepvcCountEntry 1.1.6321.1.2.3.2.13.12.2.1
An entry of paepvcCountTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PaepvcCountEntry  

paepvcCountVpi 1.1.6321.1.2.3.2.13.12.2.1.1
The PAEPVC VPI.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

paepvcCountVci 1.1.6321.1.2.3.2.13.12.2.1.2
The PAEPVC VCI.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

paepvcCountPppLcpCfgReqRx 1.1.6321.1.2.3.2.13.12.2.1.3
The number of ppp lcp config-request received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPppLcpEchoReqRx 1.1.6321.1.2.3.2.13.12.2.1.4
The number of ppp lcp echo-request received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPppLcpEchoReplyRx 1.1.6321.1.2.3.2.13.12.2.1.5
The number of ppp lcp echo-reply received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPadiTx 1.1.6321.1.2.3.2.13.12.2.1.6
The number of pppoe padi transfered
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPadoRx 1.1.6321.1.2.3.2.13.12.2.1.7
The number of pppoe pado received
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPadrTx 1.1.6321.1.2.3.2.13.12.2.1.8
The number of pppoe padr transfered
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPadsRx 1.1.6321.1.2.3.2.13.12.2.1.9
The number of pppoe pads received
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPadtTx 1.1.6321.1.2.3.2.13.12.2.1.10
The number of pppoe padt transfered
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPadtRx 1.1.6321.1.2.3.2.13.12.2.1.11
The number of pppoe padt received
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountSrvcnameErrRx 1.1.6321.1.2.3.2.13.12.2.1.12
The number of pppoe service name error received
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountAcSystemErrRx 1.1.6321.1.2.3.2.13.12.2.1.13
The number of pppoe access concentrator name error received
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountGenericErrTx 1.1.6321.1.2.3.2.13.12.2.1.14
The number of pppoe generic error transfered
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountGenericErrRx 1.1.6321.1.2.3.2.13.12.2.1.15
The number of pppoe generic error received
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

macDisplayTarget 1.1.6321.1.2.3.2.13.13.1
This managed object is a filter used for identify the target from which the MAC addresses are learned in macTable. The target could be: 99: all ports in the system 98: all subscriber ports 97: all Ethernet ports IfIndex is used for identifying subscriber ports and Ethernet Ports(e.g. 1 ~ 50).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

macTable 1.1.6321.1.2.3.2.13.13.2
A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacEntry

macEntry 1.1.6321.1.2.3.2.13.13.2.1
An entry of macTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacEntry  

macAddress 1.1.6321.1.2.3.2.13.13.2.1.1
A unicast MAC address for which the bridge has forwarding and/or filtering information.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

macPort 1.1.6321.1.2.3.2.13.13.2.1.2
The port from which the mac address has been learned.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macStatus 1.1.6321.1.2.3.2.13.13.2.1.3
The status of this entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), invalid(2), learned(3), self(4), mgmt(5)  

arpproxyTable 1.1.6321.1.2.3.2.13.14.1
Display ARP table. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ArpproxyEntry

arpproxyEntry 1.1.6321.1.2.3.2.13.14.1.1
An entry of arpproxyTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ArpproxyEntry  

arpproxyIp 1.1.6321.1.2.3.2.13.14.1.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

arpproxyMac 1.1.6321.1.2.3.2.13.14.1.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

arpproxyIfIndex 1.1.6321.1.2.3.2.13.14.1.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

arpproxyVpi 1.1.6321.1.2.3.2.13.14.1.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

arpproxyVci 1.1.6321.1.2.3.2.13.14.1.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

arpproxyInterfaceIp 1.1.6321.1.2.3.2.13.14.1.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

arpproxyInterfaceMask 1.1.6321.1.2.3.2.13.14.1.1.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

arpproxyInterfaceVid 1.1.6321.1.2.3.2.13.14.1.1.8
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

arpproxyDhcpIp 1.1.6321.1.2.3.2.13.14.1.1.9
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

arpproxyType 1.1.6321.1.2.3.2.13.14.1.1.10
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER upstream(1), downstream(2)  

ipbpvcIfDynamicTable 1.1.6321.1.2.3.2.13.14.2
Display runtime interfaces. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcIfDynamicEntry

ipbpvcIfDynamicEntry 1.1.6321.1.2.3.2.13.14.2.1
An entry of ipbpvcIfDynamicTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcIfDynamicEntry  

ipbpvcIfDynamicIp 1.1.6321.1.2.3.2.13.14.2.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipbpvcIfDynamicMask 1.1.6321.1.2.3.2.13.14.2.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcIfDynamicIfIndex 1.1.6321.1.2.3.2.13.14.2.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcIfDynamicVpi 1.1.6321.1.2.3.2.13.14.2.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcIfDynamicVci 1.1.6321.1.2.3.2.13.14.2.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcRouteDynamicTable 1.1.6321.1.2.3.2.13.14.3
Display runtime routing table. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcRouteDynamicEntry

ipbpvcRouteDynamicEntry 1.1.6321.1.2.3.2.13.14.3.1
An entry of ipbpvcRouteDynamicTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcRouteDynamicEntry  

ipbpvcRouteDynamicType 1.1.6321.1.2.3.2.13.14.3.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER upstream(1), downstream(2)  

ipbpvcRouteDynamicIp 1.1.6321.1.2.3.2.13.14.3.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipbpvcRouteDynamicMask 1.1.6321.1.2.3.2.13.14.3.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcRouteDynamicNextHop 1.1.6321.1.2.3.2.13.14.3.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipbpvcRouteDynamicMetric 1.1.6321.1.2.3.2.13.14.3.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcRouteDynamicPriority 1.1.6321.1.2.3.2.13.14.3.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

enetSfpInfoTable 1.1.6321.1.2.3.2.13.17.2
This table includes sfp info of enet port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetSfpInfoEntry

enetSfpInfoEntry 1.1.6321.1.2.3.2.13.17.2.1
An entry in enetSfpInfoTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  EnetSfpInfoEntry  

enetSfpInfoTxpower 1.1.6321.1.2.3.2.13.17.2.1.1
Measured Tx Output Power.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

enetSfpInfoRxpower 1.1.6321.1.2.3.2.13.17.2.1.2
Measured Rx Output Power.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

enetSfpInfoTemperature 1.1.6321.1.2.3.2.13.17.2.1.3
Measured temperature.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -1280000..1280000  

enetSfpInfoTxBias 1.1.6321.1.2.3.2.13.17.2.1.4
Measured tx bias.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..131000  

enetSfpInfoVoltage 1.1.6321.1.2.3.2.13.17.2.1.5
Measured voltage.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65000  

adslPortUtilTable 1.1.6321.1.2.3.2.13.18.1
This table includes adsl port utilization.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslPortUtilEntry

adslPortUtilEntry 1.1.6321.1.2.3.2.13.18.1.1
An entry in adslPortUtilEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslPortUtilEntry  

adslPortUtilTx 1.1.6321.1.2.3.2.13.18.1.1.1
Measure adsl port's tx utilization.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

adslPortUtilRx 1.1.6321.1.2.3.2.13.18.1.1.2
Measure adsl port's rx utilization.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

macFfStatsTable 1.1.6321.1.2.3.2.13.16.1
A table that contains MAC Force Forwarding static configuration and dynamic information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFfStatsEntry

macFfStatsEntry 1.1.6321.1.2.3.2.13.16.1.1
An entry of macFfStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFfStatsEntry  

macFfStatsIndex 1.1.6321.1.2.3.2.13.16.1.1.1
Index of the MACFF.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFfStatsVid 1.1.6321.1.2.3.2.13.16.1.1.2
The VLAN-ID refering to this AR/AS.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

macFfStatsArIP 1.1.6321.1.2.3.2.13.16.1.1.3
IP of this AR/AS
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

macFfStatsSrcIP 1.1.6321.1.2.3.2.13.16.1.1.4
The source IP address of the MACFF.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

macFfStatsSrcMask 1.1.6321.1.2.3.2.13.16.1.1.5
The subnet mask of source IP mask.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFfArpTable 1.1.6321.1.2.3.2.13.16.2
A table that contains MAC Force Forwarding ARP information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFfArpEntry

macFfArpEntry 1.1.6321.1.2.3.2.13.16.2.1
An entry of macFfArpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFfArpEntry  

macFfArpVid 1.1.6321.1.2.3.2.13.16.2.1.1
The VLAN-ID refering to this AR/AS.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

macFfArpIP 1.1.6321.1.2.3.2.13.16.2.1.2
IP of this AR/AS.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

macFfArpPort 1.1.6321.1.2.3.2.13.16.2.1.3
Port of this AR/AS.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFfArpMac 1.1.6321.1.2.3.2.13.16.2.1.4
MAC address of the AR or AS.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

macFfArpCounterTable 1.1.6321.1.2.3.2.13.16.3
A table that contains MAC Force Forwarding ARP counter information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFfArpCounterEntry

macFfArpCounterEntry 1.1.6321.1.2.3.2.13.16.3.1
An entry of macFfArpCounterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFfArpCounterEntry  

macFfArpCounterRequestTX 1.1.6321.1.2.3.2.13.16.3.1.1
ARP Request TX counter.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

macFfArpCounterRequestRX 1.1.6321.1.2.3.2.13.16.3.1.2
ARP Request RX counter.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

macFfArpCounterRequestRXDrop 1.1.6321.1.2.3.2.13.16.3.1.3
ARP Request RX drop counter.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

macFfArpCounterReplyTX 1.1.6321.1.2.3.2.13.16.3.1.4
ARP Reply TX counter.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

macFfArpCounterReplyRX 1.1.6321.1.2.3.2.13.16.3.1.5
ARP Reply RX counter.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

macFfArpCounterReplyRXDrop 1.1.6321.1.2.3.2.13.16.3.1.6
ARP Reply RX drop counter.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

voipLineStatusTable 1.1.6321.1.2.3.2.13.15.1
The table displays VoIP line status.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipLineStatusEntry

voipLineStatusEntry 1.1.6321.1.2.3.2.13.15.1.1
An entry of voipLineStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipLineStatusEntry  

voipLineStatusPhoneStatus 1.1.6321.1.2.3.2.13.15.1.1.1
Phone status of the line.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), onHook(2), offHook(3), ringing(4), powerCutDown(5), testing(6), fault(7), bad(8), uninitialized(9)  

voipLineStatusServiceStatus 1.1.6321.1.2.3.2.13.15.1.1.2
Service status of the line.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), outOfService(2), idle(3), waitingForDialing(4), dialingOut(5), ringing(6), conversationCaller(7), conversationCallee(8), faxModemCaller(9), faxModemCallee(10), waitingForOnHook(11), dialingTimeout(12), alertingOffHook(13), powerCutDown(14)  

voipLineInfoTable 1.1.6321.1.2.3.2.13.15.2
The table displays VoIP line information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipLineInfoEntry

voipLineInfoEntry 1.1.6321.1.2.3.2.13.15.2.1
An entry of voipLineInfoTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipLineInfoEntry  

voipLineInfoSipLocalUri 1.1.6321.1.2.3.2.13.15.2.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

voipLineInfoSipRemoteUri 1.1.6321.1.2.3.2.13.15.2.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

voipLineInfoRtpTxCodecType 1.1.6321.1.2.3.2.13.15.2.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

voipLineInfoRtpRxCodecType 1.1.6321.1.2.3.2.13.15.2.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

voipLineInfoRtpTxPt 1.1.6321.1.2.3.2.13.15.2.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipLineInfoRtpRxPt 1.1.6321.1.2.3.2.13.15.2.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipLineInfoRtpLocalIp 1.1.6321.1.2.3.2.13.15.2.1.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipLineInfoRtpRemoteIp 1.1.6321.1.2.3.2.13.15.2.1.8
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipLineInfoRtpLocalPort 1.1.6321.1.2.3.2.13.15.2.1.9
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipLineInfoRtpRemotePort 1.1.6321.1.2.3.2.13.15.2.1.10
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipLineInfoSipLocalUri2 1.1.6321.1.2.3.2.13.15.2.1.11
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

voipLineInfoSipRemoteUri2 1.1.6321.1.2.3.2.13.15.2.1.12
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

voipLineInfoRtpTxCodecType2 1.1.6321.1.2.3.2.13.15.2.1.13
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

voipLineInfoRtpRxCodecType2 1.1.6321.1.2.3.2.13.15.2.1.14
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

voipLineInfoRtpTxPt2 1.1.6321.1.2.3.2.13.15.2.1.15
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipLineInfoRtpRxPt2 1.1.6321.1.2.3.2.13.15.2.1.16
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipLineInfoRtpLocalIp2 1.1.6321.1.2.3.2.13.15.2.1.17
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipLineInfoRtpRemoteIp2 1.1.6321.1.2.3.2.13.15.2.1.18
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipLineInfoRtpLocalPort2 1.1.6321.1.2.3.2.13.15.2.1.19
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipLineInfoRtpRemotePort2 1.1.6321.1.2.3.2.13.15.2.1.20
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248Status 1.1.6321.1.2.3.2.13.15.3
OBJECT IDENTIFIER    

voipH248StatusMgName 1.1.6321.1.2.3.2.13.15.3.1
MG name.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

voipH248StatusMgStatus 1.1.6321.1.2.3.2.13.15.3.2
Mg connection status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), registering(2), registered(3), unregistering(4), unregistered(5), disconnected(6), disabled(7)  

voipActiveCallStat 1.1.6321.1.2.3.2.13.15.4
OBJECT IDENTIFIER    

voipActiveCallStatCurrentActiveCalls 1.1.6321.1.2.3.2.13.15.4.1
Number of current active calls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipActiveCallStatFailAttempts 1.1.6321.1.2.3.2.13.15.4.2
Failed attempts to setup active call.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

counterClearTarget 1.1.6321.1.2.3.2.14.1
This managed object is used for identify the target on which the counter would be cleared. The target is encoded as: Byte 1: reserved Byte 2~3: reserved Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

counterClearOps 1.1.6321.1.2.3.2.14.2
The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: clear interface counters BIT 2: clear pvc packet counters BIT 3: clear port ATM counters BIT 4: clear pvc ATM counters BIT 5: clear DHCP counters BIT 6: clear IGMP counters BIT 7: clear IGMP port counters BIT 8: clear MACFF ARP counters BIT 9: clear current lineperf BIT 10: clear current 15 minute lineperf BIT 11: clear current 1 day lineperf
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

counterClearVpi 1.1.6321.1.2.3.2.14.3
VPI of the pvc whose counters would be cleared.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

counterClearVci 1.1.6321.1.2.3.2.14.4
VCI of the pvc whose counters would be cleared.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

voipArp 1.1.6321.1.2.3.2.16.1
OBJECT IDENTIFIER    

voipSip 1.1.6321.1.2.3.2.16.2
OBJECT IDENTIFIER    

voipIp 1.1.6321.1.2.3.2.16.3
OBJECT IDENTIFIER    

voipDns 1.1.6321.1.2.3.2.16.4
OBJECT IDENTIFIER    

voipH248 1.1.6321.1.2.3.2.16.10
OBJECT IDENTIFIER    

voipRing 1.1.6321.1.2.3.2.16.11
OBJECT IDENTIFIER    

voipActiveCall 1.1.6321.1.2.3.2.16.13
OBJECT IDENTIFIER    

voipArpFlushOps 1.1.6321.1.2.3.2.16.1.1
Set the object to 1 to start flushing.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipArpShowTable 1.1.6321.1.2.3.2.16.1.2
Display ARP entries learnt in specified slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipArpShowEntry

voipArpShowEntry 1.1.6321.1.2.3.2.16.1.2.1
An entry of voipArpShowTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipArpShowEntry  

voipArpShowIp 1.1.6321.1.2.3.2.16.1.2.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipArpShowMac 1.1.6321.1.2.3.2.16.1.2.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

maxNumOfVoipNumberPlan 1.1.6321.1.2.3.2.16.2.1
The maximum number of VoIP number plan supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipNumberPlanTable 1.1.6321.1.2.3.2.16.2.2
Configure numbering plan entry of specified index in specified payphone charging table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipNumberPlanEntry

voipNumberPlanEntry 1.1.6321.1.2.3.2.16.2.2.1
An entry of voipNumberPlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipNumberPlanEntry  

voipNumberPlanName 1.1.6321.1.2.3.2.16.2.2.1.1
Numbering plan table name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipNumberPlanIndex 1.1.6321.1.2.3.2.16.2.2.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..32  

voipNumberPlanPattern 1.1.6321.1.2.3.2.16.2.2.1.3
Allowed characters are 0~9, *, T, S, P, x, ., | and range format characters that include '~', ',' and parenthesis '(', ')', brackets '[', ']', braces '{', '}' and at most one parenthesis pair are allowed, Examples: '002(*)', '0(*)', and '(*)'. '*' represents one or more digit characters 'x' represents any digit character 'T' timeout send of dial string, can only appear at the end of pattern 'S' star phone key (*) match character in dial plan 'P' pound key (#) match character in dial plan '.' represents zero or more repetitions of character or range that precedes it, can't use the dot character '.' in brackets '|' used to separate multiple number plan patterns [n~m,k] match a range of digits n~m or a specified digit k, '[' and ']' must pair and nest brackets is illegal '~' and ',' are allowed showing in brackets only '~' connected characters must be digit {n} match n digits
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

voipNumberPlanRule 1.1.6321.1.2.3.2.16.2.2.1.4
Allowed characters are 0~9, and '\c' stand for country code, '\d' stand for national destination code, '' stand for matched string enclosed by the parenthesis pair, ' ' stand for no local disconnect '\p' stand for partial pattern ' ' stand for confirmation tone play ' r' stand for recall dial tone play 'deny' stand for the pattern specified is not allowed. Examples: '', '\c', and '\c\d'.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

voipNumberPlanRowStatus 1.1.6321.1.2.3.2.16.2.2.1.5
This object is used to create a new entry or delete an existing entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

voipNumberPlanDftTable 1.1.6321.1.2.3.2.16.2.3
Configure the action rule after inter-digit timeout in specified entry of numbering plan table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipNumberPlanDftEntry

voipNumberPlanDftEntry 1.1.6321.1.2.3.2.16.2.3.1
An entry of voipNumberDftPlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipNumberPlanDftEntry  

voipNumberPlanDftRule 1.1.6321.1.2.3.2.16.2.3.1.1
Allowed characters are 0~9, and '\c' stand for country code, '\d' stand for national destination code, '' stand for matched string enclosed by the parenthesis pair, ' ' stand for no local disconnect '\p' stand for partial pattern ' ' stand for confirmation tone play 'deny' stand for the pattern specified is not allowed. Examples: '', '\c', and '\c\d'.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

digitSetup 1.1.6321.1.2.3.2.16.2.4
OBJECT IDENTIFIER    

timeoutSetup 1.1.6321.1.2.3.2.16.2.4.1
OBJECT IDENTIFIER    

initialTimeout 1.1.6321.1.2.3.2.16.2.4.1.1
First digit must be dialed before this timeout, 1 ~ 20 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..20  

interDigitTimeout 1.1.6321.1.2.3.2.16.2.4.1.2
If no pattern string is fully matched, the inter-digit timeout will trigger device to send out current dialed digits, 1 ~ 20 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..20  

digitPauseTimeout 1.1.6321.1.2.3.2.16.2.4.1.3
If a pattern string is end with the T pattern, the pattern string will not be matched until the timeout happens, 1 ~ 20 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..20  

matchingTimeout 1.1.6321.1.2.3.2.16.2.4.1.4
If a pattern string is fully matched, and there are other pattern strings partially matched, the pattern string will be sent out if the timeout happens, 1 ~ 20 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..20  

voipIpSetIp 1.1.6321.1.2.3.2.16.3.1
VoIP's IP address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

voipIpSetVid 1.1.6321.1.2.3.2.16.3.2
VoIP's VLAN ID.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

voipIpSetMask 1.1.6321.1.2.3.2.16.3.3
VoIP's network mask.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..32  

voipDnsIp 1.1.6321.1.2.3.2.16.4.1
IP address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

maxNumOfVoipRoute 1.1.6321.1.2.3.2.16.7
The maximum number of VoIP routing entries.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipRouteTable 1.1.6321.1.2.3.2.16.8
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipRouteEntry

voipRouteEntry 1.1.6321.1.2.3.2.16.8.1
An entry of voipRouteTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipRouteEntry  

voipRouteIp 1.1.6321.1.2.3.2.16.8.1.1
IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipRouteGateway 1.1.6321.1.2.3.2.16.8.1.2
Gateway IP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipRouteMask 1.1.6321.1.2.3.2.16.8.1.3
Network mask.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..32  

voipRouteMetric 1.1.6321.1.2.3.2.16.8.1.4
Metric number of the route.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..15  

voipRouteRowStatus 1.1.6321.1.2.3.2.16.8.1.5
This object is used to create a new entry or delete an existing entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

voipCountryCode 1.1.6321.1.2.3.2.16.9
Configure country (information) for VoIP services.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER usa(1)  

voipBootRegDelay 1.1.6321.1.2.3.2.16.12
Registration delay in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..30  

voipRingTable 1.1.6321.1.2.3.2.16.11.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipRingEntry

voipRingEntry 1.1.6321.1.2.3.2.16.11.1.1
An entry of voipRouteTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipRingEntry  

voipRingIndex 1.1.6321.1.2.3.2.16.11.1.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

voipRingName 1.1.6321.1.2.3.2.16.11.1.1.2
Ring identifier used in SIP Alert-Info header field
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipRingOn1 1.1.6321.1.2.3.2.16.11.1.1.3
first on time in milliseconds
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 100..10000  

voipRingOff1 1.1.6321.1.2.3.2.16.11.1.1.4
first off time in milliseconds
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 100..10000  

voipRingOn2 1.1.6321.1.2.3.2.16.11.1.1.5
second on time in milliseconds
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 100..10000  

voipRingOff2 1.1.6321.1.2.3.2.16.11.1.1.6
second off time in milliseconds
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 100..10000  

voipRingOn3 1.1.6321.1.2.3.2.16.11.1.1.7
third on time in milliseconds
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 100..10000  

voipRingOff3 1.1.6321.1.2.3.2.16.11.1.1.8
third off time in milliseconds
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 100..10000  

voipRingSetDefault 1.1.6321.1.2.3.2.16.11.2
Set the index to default value.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16  

voipActiveCallMaxActiveCalls 1.1.6321.1.2.3.2.16.13.1
Configure maximum number of concurrent active calls, 0~96.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipActiveCallThreshold 1.1.6321.1.2.3.2.16.13.2
The threshold to report or clear alarm, 50~100.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipMode 1.1.6321.1.2.3.2.16.100
Configure the Mode for VoIP Service.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER sip(1), csip(2), h248(3)  

maxNumOfVoipH248MgConf 1.1.6321.1.2.3.2.16.10.1
The maximum number of virtual media gateway supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248MgConf 1.1.6321.1.2.3.2.16.10.2
OBJECT IDENTIFIER    

voipH248MgName 1.1.6321.1.2.3.2.16.10.2.1
MG name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

voipH248MgEnable 1.1.6321.1.2.3.2.16.10.2.2
Enable/disable MG.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

voipH248MgH248Profile 1.1.6321.1.2.3.2.16.10.2.3
H248 profile name used by MG.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

voipH248MgPort 1.1.6321.1.2.3.2.16.10.2.4
Port number used by MG.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1025..65535