EQUIPE-SYSTEM-MIB

File: EQUIPE-SYSTEM-MIB.mib (57399 bytes)

Imported modules

RFC1155-SMI SNMPv2-TC SNMPv2-SMI

Imported symbols

enterprises TimeTicks TEXTUAL-CONVENTION
DisplayString RowStatus MODULE-IDENTITY
OBJECT-TYPE DateAndTime

Defined Types

EqModuleType  
Equipe system module types.
TEXTUAL-CONVENTION    
  INTEGER other(1), powerSupply(2), fanTray(3), controlProcessor(4), timingControl(5), mgmtInterface(6), processorCard(7), crossConnect(8), switchFabric(9), switchScheduler(10), universalPort16xOC3(11), universalPort8xOC12(12), universalPort16xOC12(13), universalPort4xOC48(14)  

EqModuleStatus  
Module status values.
TEXTUAL-CONVENTION    
  INTEGER diags(1), booting(2), up(3), reset(4), failed(5), disabled(6), mismatched(7)  

EqModuleHealthStatus  
module health status.
TEXTUAL-CONVENTION    
  INTEGER good(1), marginal(2), bad(3)  

EqModuleFeedStatus  
module feed status.
TEXTUAL-CONVENTION    
  INTEGER notAvail(1), good(2), bad(3)  

EqModuleRedRole  
module redundancy role.
TEXTUAL-CONVENTION    
  INTEGER notApplicable(1), primary(2), backup(3)  

EqIfType  
Equipe interface type values.
TEXTUAL-CONVENTION    
  INTEGER other(1), sonetPort(2), stsPath(3), atmIntf(4), virtAtmIntf(5)  

EqAtmPvcType  
Equipe atm pvc type values.
TEXTUAL-CONVENTION    
  INTEGER atmHardPvc(1), atmSoftPvc(2)  

EqApsLineState  
Equipe APS line state values.
TEXTUAL-CONVENTION    
  INTEGER other(1), active(2), signalFail(3), signalDegrade(4), manualSwitch(5), forceSwitch(6), clear(7), lockoutOfProtect(8)  

EqSeverityLevel  
Equipe severity levels.
TEXTUAL-CONVENTION    
  INTEGER debug(1), normal(2), informational(3), warning(4), minor(5), major(6), critical(7)  

EqFaultClass  
Fault Descriptor Class.
TEXTUAL-CONVENTION    
  INTEGER hardware(1), software(2)  

EqFaultSeverity  
Fault severity.
TEXTUAL-CONVENTION    
  INTEGER hard(1), soft(2)  

EqFaultScope  
Fault scope.
TEXTUAL-CONVENTION    
  INTEGER softwareLoadModule(1), module(2), chassis(3)  

EqReleaseVerificationStatus  
SW release verification status.
TEXTUAL-CONVENTION    
  INTEGER unverified(1), verifying(2), verified(3), noPackingList(4), parseError(5), missingModule(6), checksumError(7), internalError(8), removing(9), backupNotFound(10)  

EqReleaseUpgradeScope  
SW release upgrade scope.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), hot(1), cold(2), frosty(3)  

EqReleaseState  
SW release state.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), activeCommitted(1), active(2), committed(3), inactive(4)  

EqReleaseCommand  
The command to be performed on a release.
TEXTUAL-CONVENTION    
  INTEGER none(1), upgrade(2), delete(3), verify(4), boot(5), commit(6)  

EqReleaseCommandStatus  
The status of a command performed on a release.
TEXTUAL-CONVENTION    
  INTEGER clear(1), processing(2), done(3), error(4)  

EqReleaseSchemaChange  
Indicates if an upgrade requires a schema change.
TEXTUAL-CONVENTION    
  INTEGER change(1), nochange(2)  

EqReleaseConfigAvail  
Indicates if a release has a config file.
TEXTUAL-CONVENTION    
  INTEGER avail(1), notAvail(2)  

EqReleaseRevert  
The revert command is invoked by writing this.
TEXTUAL-CONVENTION    
  INTEGER revertInactive(1), revertActive(2), revertStart(3), revertAllowed(4), revertNotAllowed(5)  

EqEidReqEntry  
SEQUENCE    
  eqEidReqIndex INTEGER
  eqEidReqUser DisplayString
  eqEidReqCount INTEGER
  eqEidReqCountAlloc INTEGER
  eqEidReqAction INTEGER
  eqEidReqActionStatus INTEGER
  eqEidReqRowStatus RowStatus

EqEidResEntry  
SEQUENCE    
  eqEidResIndex INTEGER
  eqEidResData OBJECT IDENTIFIER

EqModuleEntry  
SEQUENCE    
  eqModuleEid INTEGER
  eqModuleShelfId INTEGER
  eqModuleSlotId INTEGER
  eqModuleType EqModuleType
  eqModuleHwVersion OCTET STRING
  eqModuleStatus EqModuleStatus
  eqModuleAction INTEGER

EqModuleHealthEntry  
SEQUENCE    
  eqModuleHealthStatus EqModuleHealthStatus
  eqModuleMemTotal INTEGER
  eqModuleMemUsed INTEGER
  eqModuleMemUsedPercent INTEGER
  eqModuleTemp INTEGER
  eqModuleCpuUtil INTEGER
  eqModuleFeedStatusA EqModuleFeedStatus
  eqModuleFeedStatusB EqModuleFeedStatus

EqHardDiskEntry  
SEQUENCE    
  eqHardDiskEid INTEGER
  eqHardDiskShelfId INTEGER
  eqHardDiskSlotId INTEGER
  eqHardDiskCapacity INTEGER
  eqHardDiskUsed INTEGER
  eqHardDiskUsedHiMark INTEGER
  eqHardDiskUsedLowMark INTEGER

EqFanUnitEntry  
SEQUENCE    
  eqFanUnitEid INTEGER
  eqFanUnitShelfId INTEGER
  eqFanUnitSlotId INTEGER
  eqFanUnitRpm INTEGER
  eqFanUnitRpmHiMark INTEGER
  eqFanUnitRpmLowMark INTEGER

EqModuleRedEntry  
SEQUENCE    
  eqModuleRedEid INTEGER
  eqModuleRedAdminRole EqModuleRedRole
  eqModuleRedOperRole EqModuleRedRole
  eqModuleRedPeerId INTEGER
  eqModuleRedAction INTEGER

EqStratumCentEntry  
SEQUENCE    
  eqStratumCentEid INTEGER
  eqStratumCentStatus INTEGER
  eqStratumCentRedStatus INTEGER
  eqStratumCentLevel INTEGER
  eqStratumCentPrimaryRefStatus INTEGER
  eqStratumCentSecondaryRefStatus INTEGER
  eqStratumCentStatusAction INTEGER
  eqStratumCentRedAction INTEGER

EqStratumLocalEntry  
SEQUENCE    
  eqStratumLocalEid INTEGER
  eqStratumLocalInputA1Status INTEGER
  eqStratumLocalInputA2Status INTEGER
  eqStratumLocalInputB1Status INTEGER
  eqStratumLocalInputB2Status INTEGER
  eqStratumLocalInputUsed INTEGER
  eqStratumLocalRecoveredRefStatus INTEGER
  eqStratumLocalStatusAction INTEGER

EqFaultEntry  
SEQUENCE    
  eqFaultDomain INTEGER
  eqFaultHandle INTEGER
  eqFaultClass EqFaultClass
  eqFaultSubclass INTEGER
  eqFaultType INTEGER
  eqFaultInstance INTEGER
  eqFaultSeverity EqFaultSeverity
  eqFaultScope EqFaultScope
  eqFaultSwlm DisplayString
  eqFaultModule INTEGER
  eqFaultTime DisplayString
  eqFaultDetails DisplayString

EqReleaseEntry  
SEQUENCE    
  eqReleaseId INTEGER
  eqReleaseName DisplayString
  eqReleaseVerificationStatus EqReleaseVerificationStatus
  eqReleaseUpgradeScope EqReleaseUpgradeScope
  eqReleaseSchemaChange EqReleaseSchemaChange
  eqReleaseState EqReleaseState
  eqReleaseModulesVerified INTEGER
  eqReleaseNumModules INTEGER
  eqReleaseBadModule DisplayString
  eqReleaseCommand EqReleaseCommand
  eqReleaseCommandStatus EqReleaseCommandStatus
  eqReleaseSchemaVersion DisplayString
  eqReleaseConfigAvail INTEGER
  eqReleaseRowStatus RowStatus

EqInstallEntry  
SEQUENCE    
  eqInstallId INTEGER
  eqInstallPath DisplayString

EqIntfBertEntry  
SEQUENCE    
  eqIntfBertEid INTEGER
  eqIntfBertGeneratorState INTEGER
  eqIntfBertMonitorState INTEGER
  eqIntfBertMonitorStatus INTEGER
  eqIntfBertMonitorOutOfSyncTime INTEGER
  eqIntfBertRequestedBitErrorCount INTEGER
  eqIntfBertInsertedBitErrorCount INTEGER
  eqIntfBertMeasuredByteErrorCount INTEGER
  eqIntfBertTestStartTime DateAndTime
  eqIntfBertTestDuration INTEGER
  eqIntfBertAction INTEGER

Defined Values

equipe 1.3.6.1.4.1.5022
OBJECT IDENTIFIER    

eqSystemMib 1.3.6.1.4.1.5022.1
This is the Equipe system MIB module.
MODULE-IDENTITY    

eqSysProducts 1.3.6.1.4.1.5022.1.1
OBJECT IDENTIFIER    

eqSysSystemGrp 1.3.6.1.4.1.5022.1.2
OBJECT IDENTIFIER    

eqSysModuleGrp 1.3.6.1.4.1.5022.1.3
OBJECT IDENTIFIER    

eqSysFaultGrp 1.3.6.1.4.1.5022.1.4
OBJECT IDENTIFIER    

eqSysSmsGrp 1.3.6.1.4.1.5022.1.5
OBJECT IDENTIFIER    

eqSysIntfGrp 1.3.6.1.4.1.5022.1.6
OBJECT IDENTIFIER    

eqSysProductE3200 1.3.6.1.4.1.5022.1.1.1
OBJECT IDENTIFIER    

eqSysSystem 1.3.6.1.4.1.5022.1.2.1
OBJECT IDENTIFIER    

eqSysConfig 1.3.6.1.4.1.5022.1.2.2
OBJECT IDENTIFIER    

eqSysModule 1.3.6.1.4.1.5022.1.3.1
OBJECT IDENTIFIER    

eqSysFault 1.3.6.1.4.1.5022.1.4.1
OBJECT IDENTIFIER    

eqSysSms 1.3.6.1.4.1.5022.1.5.1
OBJECT IDENTIFIER    

eqSysSystemId 1.3.6.1.4.1.5022.1.2.1.1
The unique value assigned to each chassis at manufacturing time.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

eqSysPhysEntLastChangeTime 1.3.6.1.4.1.5022.1.2.1.2
The value of sysUpTime when the last physical entity change event occurred (e.g. a module was inserted into the system).
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

eqSysCfgCopyConfigFileAction 1.3.6.1.4.1.5022.1.2.2.1
A read of this object always returns the value other(1). Setting this object to copyCfgFile(2) will initiate a save of the current configuration and a copy of the config file on the local filesystem. The progress of this request can be monitored by polling the eqSysCfgCopyConfigFileStatus object. The name of the saved config file, including absolute filesystem path, is stored in the eqSysCfgSavedFilename attribute.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), copyCfgFile(2)  

eqSysCfgCopyConfigFileStatus 1.3.6.1.4.1.5022.1.2.2.2
This object is used to monitor the progress of a request to save and copy the current config file on the local filesystem. The user may also do a set to reset this object to value copyCfgIdle(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER copyCfgIdle(1), copyCfgInProgress(2), copyCfgDoneSuccess(3), copyCfgDoneError(4)  

eqSysCfgSavedFilename 1.3.6.1.4.1.5022.1.2.2.3
The name assigned to the saved config file.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

eqEidReqTable 1.3.6.1.4.1.5022.1.2.3
This table is used to get equipe id values.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EqEidReqEntry

eqEidReqEntry 1.3.6.1.4.1.5022.1.2.3.1
An eid alloc entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  EqEidReqEntry  

eqEidReqIndex 1.3.6.1.4.1.5022.1.2.3.1.1
The unique value to identify this entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqEidReqUser 1.3.6.1.4.1.5022.1.2.3.1.2
A textual string to identify the owner of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

eqEidReqCount 1.3.6.1.4.1.5022.1.2.3.1.3
The count of equipe id's requested.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..400  

eqEidReqCountAlloc 1.3.6.1.4.1.5022.1.2.3.1.4
The count of equipe id's actually allocated.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..400  

eqEidReqAction 1.3.6.1.4.1.5022.1.2.3.1.5
A read of this object always returns the value other(1). Setting this object to alloc(2) will cause the agent to allocate new eid's. The number of eid's to allocate is determined by the value of eqEidReqCount object. The agent will create an entry in the eqEidResultTable containing the allocated eid's. The NMS can retrieve these values by doing a getnext using the eqEidReqIndex for this entry as the key.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), alloc(2)  

eqEidReqActionStatus 1.3.6.1.4.1.5022.1.2.3.1.6
The result of the action requested.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), reqSuccess(2), reqErrorReqCountTooBig(3), reqErrorEidsUnavailable(4)  

eqEidReqRowStatus 1.3.6.1.4.1.5022.1.2.3.1.7
This object is used to create and delete entries in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

eqEidResTable 1.3.6.1.4.1.5022.1.2.4
This table contains entries for allocated eid's.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EqEidResEntry

eqEidResEntry 1.3.6.1.4.1.5022.1.2.4.1
An eid result entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  EqEidResEntry  

eqEidResIndex 1.3.6.1.4.1.5022.1.2.4.1.1
The id value to identify this entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqEidResData 1.3.6.1.4.1.5022.1.2.4.1.2
An array holding the allocated eid values.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

eqModuleTable 1.3.6.1.4.1.5022.1.3.1.1
This table contains module info.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EqModuleEntry

eqModuleEntry 1.3.6.1.4.1.5022.1.3.1.1.1
A module entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  EqModuleEntry  

eqModuleEid 1.3.6.1.4.1.5022.1.3.1.1.1.1
The unique id assigned to the module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqModuleShelfId 1.3.6.1.4.1.5022.1.3.1.1.1.2
The shelf id in which this module is located.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

eqModuleSlotId 1.3.6.1.4.1.5022.1.3.1.1.1.3
The slot id in which this module is located.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

eqModuleType 1.3.6.1.4.1.5022.1.3.1.1.1.4
The type of module.
Status: current Access: read-only
OBJECT-TYPE    
  EqModuleType  

eqModuleHwVersion 1.3.6.1.4.1.5022.1.3.1.1.1.5
The hardware version of the module.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

eqModuleStatus 1.3.6.1.4.1.5022.1.3.1.1.1.6
The module status.
Status: current Access: read-only
OBJECT-TYPE    
  EqModuleStatus  

eqModuleAction 1.3.6.1.4.1.5022.1.3.1.1.1.7
A read of this object always returns the value other(1). Setting this to reset(2) causes the module to be reset.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

eqModuleHealthTable 1.3.6.1.4.1.5022.1.3.1.2
This table contains module health info.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EqModuleHealthEntry

eqModuleHealthEntry 1.3.6.1.4.1.5022.1.3.1.2.1
A module health entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  EqModuleHealthEntry  

eqModuleHealthStatus 1.3.6.1.4.1.5022.1.3.1.2.1.1
The module health status.
Status: current Access: read-only
OBJECT-TYPE    
  EqModuleHealthStatus  

eqModuleMemTotal 1.3.6.1.4.1.5022.1.3.1.2.1.2
The total amount of sdram memory available on the module in megabytes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..20000  

eqModuleMemUsed 1.3.6.1.4.1.5022.1.3.1.2.1.3
The amount of used sdram memory on the module in megabytes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..20000  

eqModuleMemUsedPercent 1.3.6.1.4.1.5022.1.3.1.2.1.4
The amount of used sdram memory expressed as a percentage of total available memory.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

eqModuleTemp 1.3.6.1.4.1.5022.1.3.1.2.1.5
The temp of the module in degrees centigrades.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

eqModuleCpuUtil 1.3.6.1.4.1.5022.1.3.1.2.1.6
The cpu utilization of the module as a percentage.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

eqModuleFeedStatusA 1.3.6.1.4.1.5022.1.3.1.2.1.7
The module power feed A status.
Status: current Access: read-only
OBJECT-TYPE    
  EqModuleFeedStatus  

eqModuleFeedStatusB 1.3.6.1.4.1.5022.1.3.1.2.1.8
The module power feed B status.
Status: current Access: read-only
OBJECT-TYPE    
  EqModuleFeedStatus  

eqHardDiskTable 1.3.6.1.4.1.5022.1.3.1.3
The hard disk status table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EqHardDiskEntry

eqHardDiskEntry 1.3.6.1.4.1.5022.1.3.1.3.1
A hard disk entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  EqHardDiskEntry  

eqHardDiskEid 1.3.6.1.4.1.5022.1.3.1.3.1.1
The unique id assigned to the hard disk.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqHardDiskShelfId 1.3.6.1.4.1.5022.1.3.1.3.1.2
The shelf id in which this hard disk is located.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

eqHardDiskSlotId 1.3.6.1.4.1.5022.1.3.1.3.1.3
The slot id in which this hard disk is located.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

eqHardDiskCapacity 1.3.6.1.4.1.5022.1.3.1.3.1.4
The hard disk capacity in megabytes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..100000  

eqHardDiskUsed 1.3.6.1.4.1.5022.1.3.1.3.1.5
The percentage of hard disk in use.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..100  

eqHardDiskUsedHiMark 1.3.6.1.4.1.5022.1.3.1.3.1.6
The percentage of hard disk in use which, when crossed, will trigger an eqHardDiskUsedHiMark trap to be generated.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..100  

eqHardDiskUsedLowMark 1.3.6.1.4.1.5022.1.3.1.3.1.7
The percentage of hard disk in use which, when crossed, will trigger an eqHardDiskLowMark trap to be generated.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..100  

eqFanUnitTable 1.3.6.1.4.1.5022.1.3.1.4
The fan unit status table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EqFanUnitEntry

eqFanUnitEntry 1.3.6.1.4.1.5022.1.3.1.4.1
A fan unit entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  EqFanUnitEntry  

eqFanUnitEid 1.3.6.1.4.1.5022.1.3.1.4.1.1
The unique id assigned to the fan unit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqFanUnitShelfId 1.3.6.1.4.1.5022.1.3.1.4.1.2
The shelf id in which this fan unit is located.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

eqFanUnitSlotId 1.3.6.1.4.1.5022.1.3.1.4.1.3
The slot id in which this fan unit is located.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

eqFanUnitRpm 1.3.6.1.4.1.5022.1.3.1.4.1.4
The current rpm of this fan unit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..1000  

eqFanUnitRpmHiMark 1.3.6.1.4.1.5022.1.3.1.4.1.5
The fan unit rpm which, when crossed, will trigger an eqFanUnitUsedHiMark trap to be generated.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..1000  

eqFanUnitRpmLowMark 1.3.6.1.4.1.5022.1.3.1.4.1.6
The fan unit rpm which, when crossed, will trigger an eqFanUnitUsedLowMark trap to be generated.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..1000  

eqModuleRedTable 1.3.6.1.4.1.5022.1.3.1.5
This table contains module redundancy info.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EqModuleRedEntry

eqModuleRedEntry 1.3.6.1.4.1.5022.1.3.1.5.1
A module redundancy entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  EqModuleRedEntry  

eqModuleRedEid 1.3.6.1.4.1.5022.1.3.1.5.1.1
The unique id assigned to the module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqModuleRedAdminRole 1.3.6.1.4.1.5022.1.3.1.5.1.2
The module's configured redundancy role.
Status: current Access: read-only
OBJECT-TYPE    
  EqModuleRedRole  

eqModuleRedOperRole 1.3.6.1.4.1.5022.1.3.1.5.1.3
The module's current redundancy role.
Status: current Access: read-only
OBJECT-TYPE    
  EqModuleRedRole  

eqModuleRedPeerId 1.3.6.1.4.1.5022.1.3.1.5.1.4
The id of the module that is a peer to this module. The peer can be either a primary or a backup module. A value of zero indicates no peer module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

eqModuleRedAction 1.3.6.1.4.1.5022.1.3.1.5.1.5
A read of this object always returns the value other(1). Setting this to switchRole(2) causes the module to switch role with it's peer module.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), switchRole(2)  

eqStratumCentTable 1.3.6.1.4.1.5022.1.3.1.6
This table contains the central stratum timing subsystem info.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EqStratumCentEntry

eqStratumCentEntry 1.3.6.1.4.1.5022.1.3.1.6.1
A central stratum timing subsystem entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  EqStratumCentEntry  

eqStratumCentEid 1.3.6.1.4.1.5022.1.3.1.6.1.1
The unique id assigned to the module containing the central stratum timing subsystem.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqStratumCentStatus 1.3.6.1.4.1.5022.1.3.1.6.1.2
The status of the central stratum timing subsystem.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), freeRun(2), holdover(3), lockedPrimary(4), lockedSecondary(5)  

eqStratumCentRedStatus 1.3.6.1.4.1.5022.1.3.1.6.1.3
The redundancy status of the central stratum timing subsystem.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER reset(1), offline(2), standby(3), online(4)  

eqStratumCentLevel 1.3.6.1.4.1.5022.1.3.1.6.1.4
The level of the central stratum timing subsystem.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER stratum1(1), stratum2(2), stratum3E(3), stratum3(4), stratum4(5), sonetMin(6)  

eqStratumCentPrimaryRefStatus 1.3.6.1.4.1.5022.1.3.1.6.1.5
The primary reference status of the central stratum timing subsystem.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER qualified(1), noSignal(2), outOfRange(3), outOfLock(4)  

eqStratumCentSecondaryRefStatus 1.3.6.1.4.1.5022.1.3.1.6.1.6
The secondary reference status of the central stratum timing subsystem.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER qualified(1), noSignal(2), outOfRange(3), outOfLock(4)  

eqStratumCentStatusAction 1.3.6.1.4.1.5022.1.3.1.6.1.7
This object is used to change the status of the central stratum timing subsystem. A read of this object always returns the value other(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), freeRun(2), holdOver(3), lockedPrimary(4), lockedSecondary(5)  

eqStratumCentRedAction 1.3.6.1.4.1.5022.1.3.1.6.1.8
This object is used to change the redundancy status of the central stratum timing subsystem. A read of this object always returns the value other(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), reset(2), offline(3), standby(4), online(5)  

eqStratumLocalTable 1.3.6.1.4.1.5022.1.3.1.7
This table contains the local stratum timing subsystem info.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EqStratumLocalEntry

eqStratumLocalEntry 1.3.6.1.4.1.5022.1.3.1.7.1
A local stratum timing subsystem entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  EqStratumLocalEntry  

eqStratumLocalEid 1.3.6.1.4.1.5022.1.3.1.7.1.1
The unique id assigned to the module containing the local stratum timing subsystem.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqStratumLocalInputA1Status 1.3.6.1.4.1.5022.1.3.1.7.1.2
The input A1 status of the local stratum timing subsystem.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER signal(1), noSignal(2)  

eqStratumLocalInputA2Status 1.3.6.1.4.1.5022.1.3.1.7.1.3
The input A2 status of the local stratum timing subsystem.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER signal(1), noSignal(2)  

eqStratumLocalInputB1Status 1.3.6.1.4.1.5022.1.3.1.7.1.4
The input B1 status of the local stratum timing subsystem.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER signal(1), noSignal(2)  

eqStratumLocalInputB2Status 1.3.6.1.4.1.5022.1.3.1.7.1.5
The input B2 status of the local stratum timing subsystem.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER signal(1), noSignal(2)  

eqStratumLocalInputUsed 1.3.6.1.4.1.5022.1.3.1.7.1.6
This object indicates which of the two inputs on the local startum timing subsystem is currently being used.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), usingInputA(2), usingInputB(3)  

eqStratumLocalRecoveredRefStatus 1.3.6.1.4.1.5022.1.3.1.7.1.7
This object indicates if this local startum timing subsystem is providing a reference source to either of the two inputs.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), priRef(2), secRef(3)  

eqStratumLocalStatusAction 1.3.6.1.4.1.5022.1.3.1.7.1.8
This object is used to change the input being used by the local stratum timing subsystem. A read of this object always returns the value other(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), useNeither(2), useInputA(3), useInputB(4)  

eqFaultTable 1.3.6.1.4.1.5022.1.4.1.1
This table contains fault info.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EqFaultEntry

eqFaultEntry 1.3.6.1.4.1.5022.1.4.1.1.1
A fault entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  EqFaultEntry  

eqFaultDomain 1.3.6.1.4.1.5022.1.4.1.1.1.1
The domain of the entity handling the fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqFaultHandle 1.3.6.1.4.1.5022.1.4.1.1.1.2
The handle of the fault within the domain.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqFaultClass 1.3.6.1.4.1.5022.1.4.1.1.1.3
The class field of the fault descriptor.
Status: current Access: read-only
OBJECT-TYPE    
  EqFaultClass  

eqFaultSubclass 1.3.6.1.4.1.5022.1.4.1.1.1.4
The subclass field of the fault descriptor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqFaultType 1.3.6.1.4.1.5022.1.4.1.1.1.5
The type field of the fault descriptor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqFaultInstance 1.3.6.1.4.1.5022.1.4.1.1.1.6
The instance field of the fault descriptor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqFaultSeverity 1.3.6.1.4.1.5022.1.4.1.1.1.7
The severity of the fault.
Status: current Access: read-only
OBJECT-TYPE    
  EqFaultSeverity  

eqFaultScope 1.3.6.1.4.1.5022.1.4.1.1.1.8
The scope in which the fault was handled.
Status: current Access: read-only
OBJECT-TYPE    
  EqFaultScope  

eqFaultSwlm 1.3.6.1.4.1.5022.1.4.1.1.1.9
A textual string to identify the type of swlm if scope is swlm.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

eqFaultModule 1.3.6.1.4.1.5022.1.4.1.1.1.10
The EID of the physical module on which the fault occurred.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqFaultTime 1.3.6.1.4.1.5022.1.4.1.1.1.11
A textual string indicating the time at which the fault occurred.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

eqFaultDetails 1.3.6.1.4.1.5022.1.4.1.1.1.12
A textual string providing additional details about the fault.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

eqReleaseNextId 1.3.6.1.4.1.5022.1.5.1.1
The next available release id value.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqReleaseRevert 1.3.6.1.4.1.5022.1.5.1.2
Writing this initiates a revert to the default release.
Status: current Access: read-write
OBJECT-TYPE    
  EqReleaseRevert  

eqReleaseTable 1.3.6.1.4.1.5022.1.5.1.3
This table contains installed software release status and control.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EqReleaseEntry

eqReleaseEntry 1.3.6.1.4.1.5022.1.5.1.3.1
A software release entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  EqReleaseEntry  

eqReleaseId 1.3.6.1.4.1.5022.1.5.1.3.1.1
A box unique number which identifies the release .
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqReleaseName 1.3.6.1.4.1.5022.1.5.1.3.1.2
The name of the release.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

eqReleaseVerificationStatus 1.3.6.1.4.1.5022.1.5.1.3.1.3
The verification status of the release.
Status: current Access: read-only
OBJECT-TYPE    
  EqReleaseVerificationStatus  

eqReleaseUpgradeScope 1.3.6.1.4.1.5022.1.5.1.3.1.4
The scope of an upgrade to this release with respect to the current release.
Status: current Access: read-only
OBJECT-TYPE    
  EqReleaseUpgradeScope  

eqReleaseSchemaChange 1.3.6.1.4.1.5022.1.5.1.3.1.5
The state of the release.
Status: current Access: read-only
OBJECT-TYPE    
  EqReleaseSchemaChange  

eqReleaseState 1.3.6.1.4.1.5022.1.5.1.3.1.6
The state of the release.
Status: current Access: read-only
OBJECT-TYPE    
  EqReleaseState  

eqReleaseModulesVerified 1.3.6.1.4.1.5022.1.5.1.3.1.7
The number of modules that have been verified.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000  

eqReleaseNumModules 1.3.6.1.4.1.5022.1.5.1.3.1.8
The number of modules contained in the release.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000  

eqReleaseBadModule 1.3.6.1.4.1.5022.1.5.1.3.1.9
The the name of a missing module or one with a checksum error.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

eqReleaseCommand 1.3.6.1.4.1.5022.1.5.1.3.1.10
A command to peform on the release
Status: current Access: read-create
OBJECT-TYPE    
  EqReleaseCommand  

eqReleaseCommandStatus 1.3.6.1.4.1.5022.1.5.1.3.1.11
The status of a command contained in eqReleaseCommand
Status: current Access: read-create
OBJECT-TYPE    
  EqReleaseCommandStatus  

eqReleaseSchemaVersion 1.3.6.1.4.1.5022.1.5.1.3.1.12
The schema's version string for the release
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

eqReleaseConfigAvail 1.3.6.1.4.1.5022.1.5.1.3.1.13
Indicates if the release has a config file
Status: current Access: read-only
OBJECT-TYPE    
  EqReleaseConfigAvail  

eqReleaseRowStatus 1.3.6.1.4.1.5022.1.5.1.3.1.14
This object is used to create and delete entries in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

eqInstallTable 1.3.6.1.4.1.5022.1.5.1.4
This table contains the paths where a new image should be installed.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EqInstallEntry

eqInstallEntry 1.3.6.1.4.1.5022.1.5.1.4.1
An install entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  EqInstallEntry  

eqInstallId 1.3.6.1.4.1.5022.1.5.1.4.1.1
A box unique number which identifies the installation path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqInstallPath 1.3.6.1.4.1.5022.1.5.1.4.1.2
The full name of the installation path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

eqUpgradeState 1.3.6.1.4.1.5022.1.5.1.5
The current state of an upgrade.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

eqIntfBertTable 1.3.6.1.4.1.5022.1.6.1
This table is used to initiate a Bit Error Rate Test (BERT) on a sonet port and also for reading statistics on the initiated test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EqIntfBertEntry

eqIntfBertEntry 1.3.6.1.4.1.5022.1.6.1.1
A BERT entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  EqIntfBertEntry  

eqIntfBertEid 1.3.6.1.4.1.5022.1.6.1.1.1
The eid assigned to the interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

eqIntfBertGeneratorState 1.3.6.1.4.1.5022.1.6.1.1.2
The current BERT generator state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

eqIntfBertMonitorState 1.3.6.1.4.1.5022.1.6.1.1.3
The current BERT monitor state. A value of active(1) indicates that a BERT test is currently running.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

eqIntfBertMonitorStatus 1.3.6.1.4.1.5022.1.6.1.1.4
The BERT monitor status value. Note that this object is only valid when a BERT test is running.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inSync(1), outOfSync(2)  

eqIntfBertMonitorOutOfSyncTime 1.3.6.1.4.1.5022.1.6.1.1.5
The total amount of time, in seconds, that the monitor has been out of synch since the BERT test was started.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

eqIntfBertRequestedBitErrorCount 1.3.6.1.4.1.5022.1.6.1.1.6
The number of bit errors the user wants inserted onto the interface. This value is used when the user issues a bit error request by a set to the eqIntfBertAction object.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

eqIntfBertInsertedBitErrorCount 1.3.6.1.4.1.5022.1.6.1.1.7
The actual number of bit errors inserted onto the interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

eqIntfBertMeasuredByteErrorCount 1.3.6.1.4.1.5022.1.6.1.1.8
The number of byte errors measured on the interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

eqIntfBertTestStartTime 1.3.6.1.4.1.5022.1.6.1.1.9
The time that the test was started.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

eqIntfBertTestDuration 1.3.6.1.4.1.5022.1.6.1.1.10
The time, in seconds, that the test has been running.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

eqIntfBertAction 1.3.6.1.4.1.5022.1.6.1.1.11
A read of this object always returns the value other(1). Setting this object to insertBitError(2) inserts a bit error on the interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), insertBitError(2)