ERI-DNX-T3-MIB
File:
ERI-DNX-T3-MIB.mib (23837 bytes)
Imported modules
Imported symbols
Defined Types
T3PortConfigEntry |
|
SEQUENCE |
|
|
|
|
t3CfgAddr |
LinkPortAddress |
|
|
t3CfgResource |
Integer32 |
|
|
t3CfgCircuitName |
DisplayString |
|
|
t3FacilityId |
DisplayString |
|
|
t3EquipmentId |
DisplayString |
|
|
t3Location |
DisplayString |
|
|
t3FrameId |
DisplayString |
|
|
t3UnitName |
DisplayString |
|
|
t3PortNumber |
DisplayString |
|
|
t3Generator |
DisplayString |
|
|
t3M13OpMode |
INTEGER |
|
|
t3RcvLoopTiming |
FunctionSwitch |
|
|
t3ShortCable |
DecisionType |
|
|
t3M13RemLoop |
INTEGER |
|
|
t3RcvAIS |
INTEGER |
|
|
t3XmtAIS |
INTEGER |
|
|
t3CmdStatus |
LinkCmdStatus |
|
T3T1LinkConfigEntry |
|
SEQUENCE |
|
|
|
|
t3T1CfgLinkAddr |
LinkPortAddress |
|
|
t3T1CfgResource |
Integer32 |
|
|
t3T1CfgLinkName |
DisplayString |
|
|
t3T1Status |
PortStatus |
|
|
t3T1Framing |
INTEGER |
|
|
t3T1Density |
INTEGER |
|
|
t3T1NetLoop |
INTEGER |
|
|
t3T1YelAlrm |
INTEGER |
|
|
t3T1RecoverTime |
INTEGER |
|
|
t3T1EsfFormat |
INTEGER |
|
|
t3T1IdleCode |
INTEGER |
|
|
t3T1CfgCmdStatus |
LinkCmdStatus |
|
Defined Values
eriDNXT3MIB |
1.3.6.1.4.1.644.3.3 |
The ERI Enterprise MIB Module for the DNX T3 Device. |
MODULE-IDENTITY |
|
|
|
dnxT3 |
1.3.6.1.4.1.644.2.4.2.1 |
OBJECT IDENTIFIER |
|
|
|
t3Config |
1.3.6.1.4.1.644.2.4.2.1.1 |
OBJECT IDENTIFIER |
|
|
|
t3Diag |
1.3.6.1.4.1.644.2.4.2.1.2 |
OBJECT IDENTIFIER |
|
|
|
t3PortConfigTable |
1.3.6.1.4.1.644.2.4.2.1.1.1 |
This is the T3 Port Configuration table which consists
of an entry for each of the T3 cards. The total number of
entries depends on the number of T3 cards in the nest. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
T3PortConfigEntry |
|
t3PortConfigEntry |
1.3.6.1.4.1.644.2.4.2.1.1.1.1 |
The conceptual row of the T3 Port Configuration table.
A row in this table cannot be added or deleted, only modified. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
T3PortConfigEntry |
|
|
t3CfgAddr |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.1 |
This number uniquely identifies a T3 slot/port. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
LinkPortAddress |
|
|
t3CfgResource |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.2 |
Uniquely identifies an T3 Port in the system.
This number is provided as key to allow the manager to
map this entry to a corresponding Resource Table entry. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
t3CfgCircuitName |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.3 |
This is the user friendly text name to identify the circuit. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..20) |
|
t3FacilityId |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.4 |
This is a description of the facility where this equipment
is located. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..37) |
|
t3EquipmentId |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.5 |
This is a description of the equipment in use. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..9) |
|
t3Location |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.6 |
This is the user description of the location for this equipment. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..10) |
|
t3FrameId |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.7 |
This is the description of the building where this equipment is
located. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..9) |
|
t3UnitName |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.8 |
This is the description of the bay or device this equipment
is part of. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..5) |
|
t3PortNumber |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.9 |
This is the user description of the DS3 port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..37) |
|
t3Generator |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.10 |
This is the user description of the number generated by this
equipment. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..37) |
|
t3M13OpMode |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.11 |
The framing selection for the DS1 to DS3 multiplexing. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
c-bit(0), bellcoreM13(1) |
|
t3RcvLoopTiming |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.12 |
Enables or disables the DS3 transmit timing provided by the
receive clock. When disabled, timing is provided by an on-board
oscillator. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
FunctionSwitch |
|
|
t3ShortCable |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.13 |
Indicates the line build out of the DS3 transmitter. 'Yes' when
attached to a cable less than 50 feet long. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DecisionType |
|
|
t3M13RemLoop |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.14 |
Controls the line codes used to set and reset DS1 remote line
loopback requests. This applies the BellCore M13 mode only. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
third-cbit-inverted(0), second-cbit-inverted(1), first-cbit-inverted(2), third-cbit-stuffbit-inverted(4), second-cbit-stuffbit-inverted(5), first-cbit-stuffbit-inverted(6), stuffbit-inverted(7), stuffbit-is-zero(8), stuffbit-is-one(9) |
|
t3RcvAIS |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.15 |
The Received bit pattern that will cause an error. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
framed1010-Cbit0-noXbit(0), framed1010-Cbit0-Xbit1(1), framed1010-noCbit-noXbit(2), framed1111-noCbit-noXbit(3), unframed1010(4), unframed-allones(5) |
|
t3XmtAIS |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.16 |
The Transmitted bit pattern that will cause an error. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
ansi(0), framed-allones-Cbit1(1), unframed1010(2), unframed-allones(3) |
|
t3CmdStatus |
1.3.6.1.4.1.644.2.4.2.1.1.1.1.17 |
The command status for this link configuration row/record.
The value used in a SET will be replaced by a response
value in the GET RESPONSE indicating success or failure.
Default Response State used in GET RESPONSE Command
ready-for-command (0)
initial default status for a row
T3 Link Commands used in SET Command (1..99)
update-link-config(1),
Change existing Link Configuration
Response States used in GET RESPONSE Command (100..199)
update-successful (101)
Link data has been successfully changed
T3 Port Config Error Codes used in GET RESPONSE Command (100..699)
err-general-link-config-error (400)
Unknown link configuration error occurred
err-invalid-link-status (401)
Unrecognized link status setting
err-invalid-link-framing (402)
Line framing type not valid for link type
err-invalid-link-command (403)
Unrecognized link command-action
err-invalid-link-op-mode (407)
Configured M13 Op mode not valid for port; verify other
link parameters match desired new mode
err-invalid-link-rem-loop (408)
Remote Loop type not valid for t3 frame type
err-invalid-link-ais (409)
Unrecognized t3 AIS selection
err-data-locked-by-another-user (450)
Another administrative user is making changes to this
part of the system via a terminal session. Check Event
Log for user name
err-snmp-parse-failed (500)
Agent could not parse variable
err-invalid-snmp-type (501)
Variable ASN type does not match Agent defined type
err-invalid-snmp-var-size (502)
Variable size is too big |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
LinkCmdStatus |
|
|
t3T1LinkConfigTable |
1.3.6.1.4.1.644.2.4.2.1.1.2 |
This is the T3 T-1 Link Configuration table which consists
of an entry for each of the card's 28 links. The total number of
entries depends on the number of DS3 cards in the nest. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
T3T1LinkConfigEntry |
|
t3T1LinkConfigEntry |
1.3.6.1.4.1.644.2.4.2.1.1.2.1 |
The conceptual row of the T3 T-1 Link Configuration table.
A row in this table cannot be added or deleted, only modified. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
T3T1LinkConfigEntry |
|
|
t3T1CfgLinkAddr |
1.3.6.1.4.1.644.2.4.2.1.1.2.1.1 |
This number uniquely identifies a T3/T-1 link resource.
This number will be used throughout the system to identify
a unique resource. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
LinkPortAddress |
|
|
t3T1CfgResource |
1.3.6.1.4.1.644.2.4.2.1.1.2.1.2 |
Uniquely identifies an T3 T1 Channel in the system.
This number is provided as key to allow the manager to
map this entry to a corresponding Resource Table entry. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
t3T1CfgLinkName |
1.3.6.1.4.1.644.2.4.2.1.1.2.1.3 |
This is the user friendly text name to identify the link. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..20) |
|
t3T1Status |
1.3.6.1.4.1.644.2.4.2.1.1.2.1.4 |
Dictates the current status of the link, in-service or
out-of-service. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
PortStatus |
|
|
t3T1Framing |
1.3.6.1.4.1.644.2.4.2.1.1.2.1.5 |
Determines the type of framing used on the line. Choose between
SuperFrame 'D4' or Extended SuperFrame (ESF). |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
d4(1), esf(3) |
|
t3T1Density |
1.3.6.1.4.1.644.2.4.2.1.1.2.1.6 |
Determines the type of network signal used on the link. If line
code is B8ZS, choose 'clear'. If line code is AMI, choose 62411. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
clear(0), att-62411(1) |
|
t3T1NetLoop |
1.3.6.1.4.1.644.2.4.2.1.1.2.1.7 |
Determines whether or not the module should respond to loop
diagnostic commands received from the network supplier. Select
'enable' unless the commands are to be passed to another DS3
device. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
FunctionSwitch |
|
|
t3T1YelAlrm |
1.3.6.1.4.1.644.2.4.2.1.1.2.1.8 |
Causes the module to discard data and send a yellow alarm if it
is in a red alarm condition after a 3 second period. 'Yes' must
be chosen if the network supplier is a common carrier, such as a
telephone company. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DecisionType |
|
|
t3T1RecoverTime |
1.3.6.1.4.1.644.2.4.2.1.1.2.1.9 |
This is the red alarm timeout value. Determines the amount
of seconds the port will wait to stop sending the yellow alarm
when coming out of a red alarm condition. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
timeout-3-secs(3), timeout-10-secs(10), timeout-15-secs(15) |
|
t3T1IdleCode |
1.3.6.1.4.1.644.2.4.2.1.1.2.1.11 |
Determines the whether the code that will be transmitted over
the unused links will be 'idle' or 'busy' (all 1's). |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
busy(0), idle(1) |
|
t3T1CfgCmdStatus |
1.3.6.1.4.1.644.2.4.2.1.1.2.1.12 |
The command status for this link configuration row/record.
The value used in a SET will be replaced by a response
value in the GET RESPONSE indicating success or failure.
Default Response State used in GET RESPONSE Command
ready-for-command (0)
initial default status for a row
T3-T1 Link Commands used in SET Command (1..99)
update-link-config(1)
Change existing Link Configuration
inServiceAll (7)
Change Link Status to in-service for all 8 links.
copyToAll (9)
Copy T1 Link configuration to all other links
within the same device
outOfServiceAll (12)
Change Link Status to out-of-service for all 8 links.
Response States used in GET RESPONSE Command (100..199)
update-successful (101)
Link data has been successfully changed
insvc-successful (107)
All Links have been successfully placed In Service
copy-successful (109)
T1 Link data has been successfully copied to other links
oos-successful (112)
All Links have been successfully placed Out of Service
T3-T1 Link Config Error Codes used in GET RESPONSE Command (200..699)
err-general-link-config-error (400)
Unknown link configuration error occurred
err-invalid-link-status (401)
Unrecognized link status setting
err-invalid-link-framing (402)
Line framing type not valid for link type
err-invalid-link-command (403)
Unrecognized link command-action
err-invalid-esf-format (405)
ESF type not applicable to link type
err-invalid-link-density (406)
Unrecognized T1 link density setting
err-invalid-network-loop (410)
Unrecognized network loop setting
err-invalid-yellow-alrm (411)
Unrecognized yellow alarm setting
err-invalid-red-timeout (412)
Unrecognized red alarm timeout
err-invalid-idle-code (413)
Unrecognized idle code
err-device-in-standby (414)
Can't change config for designated Standby device
err-data-locked-by-another-user (450)
Another administrative user is making changes to this
part of the system via a terminal session. Check Event
Log for user name
err-snmp-parse-failed (500)
Agent could not parse variable
err-invalid-snmp-type (501)
Variable ASN type does not match Agent defined type
err-invalid-snmp-var-size (502)
Variable size is too big |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
LinkCmdStatus |
|
|
dnxT3Enterprise |
1.3.6.1.4.1.644.2.4.2.1.0 |
ERI DNX T3 Enterprise for Alarms/Events |
Status: current |
Access: read-write |
OBJECT-IDENTITY |
|
|
|
t3PortConfigTrap |
1.3.6.1.4.1.644.2.4.2.1.0.1 |
This trap is used to notify a NMS that a user has updated
the configuration for a given T3 Port entry. |
Status: current |
Access: read-write |
NOTIFICATION-TYPE |
|
|
|
t3T1ConfigTrap |
1.3.6.1.4.1.644.2.4.2.1.0.2 |
This trap is used to notify a NMS that a user has updated
the Link configuration for a given T3-T1 channel entry. |
Status: current |
Access: read-write |
NOTIFICATION-TYPE |
|
|
|