ES-MODULE-MIB

Imported modules

Imported symbols

enterprises	Counter	TimeTicks
OBJECT-TYPE	DisplayString

Defined Types

EsModuleEntry
SEQUENCE
	esModuleIndex	INTEGER
	esModuleStatus	INTEGER
	esModuleAdminStatus	INTEGER
	esModuleDescr	DisplayString
	esModuleID	DisplayString
	esModuleVersion	INTEGER
	esModuleObjectID	OBJECT IDENTIFIER
	esModulePortCapacity	INTEGER
	esModuleReset	INTEGER
	esModuleLastStatusChange	TimeTicks
	esModuleCollisionPeriods	Counter
	esModuleLinkDisplayMap	OCTET STRING
	esModuleDisabledDisplayMap	OCTET STRING
	esModuleBroadcastStormBlocked	INTEGER
	esModuleFirmwareVersion	DisplayString
	esModuleBOOTCodeVersion	DisplayString
	esModuleFlashStatus	DisplayString
	esModuleResetToFactoryDefaults	INTEGER
	esModuleSwPortIndex	INTEGER

EsModulePortEntry
SEQUENCE
	esModuleSlotIndex	INTEGER
	esModulePortIndex	INTEGER
	esModulePortDescr	DisplayString
	esModulePortAdminStatus	INTEGER
	esModulePortAutoPartitionState	INTEGER
	esModulePortOperStatus	INTEGER
	esModulePortLinkbeatStatus	INTEGER
	esModulePortConnectorType	INTEGER
	esModulePortReceivePeriods	Counter

FmCfgEntry
SEQUENCE
	fmCfgIndex	INTEGER
	fmCfgFirmwareVersion	DisplayString
	fmCfgBOOTCodeVersion	DisplayString
	fmCfgPOSTResult	INTEGER
	fmCfgPOSTTest	INTEGER
	fmCfgPOSTLoopbackResult	INTEGER
	fmCfgFlashStatus	DisplayString
	fmCfgResetToFactoryDefaults	INTEGER
	fmCfgResetModule	INTEGER
	fmCfgNovellFDDISNAPTranslation	INTEGER
	fmCfgUnmatchedSNAPDestination	INTEGER
	fmCfgAuthorizationChecking	INTEGER
	fmCfgAuthorizationString	DisplayString

FmXlateToEthEntry
SEQUENCE
	fmXlateToEthIndex	INTEGER
	fmXlateToEthNovellSnapToRaw8023Frames	Counter
	fmXlateToEthNovellSnapToEthIIFrames	Counter
	fmXlateToEthNovellSnapToSnapFrames	Counter
	fmXlateToEthAppleTalkSnapToSnapFrames	Counter
	fmXlateToEthIpSnapForFragmentationFrames	Counter
	fmXlateToEthIpSnapFragmentedFrames	Counter
	fmXlateToEthBridgeTunnelToEthIIFrames	Counter
	fmXlateToEthOtherSnapToEthIIFrames	Counter
	fmXlateToEthOtherSnapToSnapFrames	Counter
	fmXlateToEth8022To8022Frames	Counter

FmXlateToFDDIEntry
SEQUENCE
	fmXlateToFDDIIndex	INTEGER
	fmXlateToFDDINovellRaw8023ToSnapFrames	Counter
	fmXlateToFDDINovellEthIIToSnapFrames	Counter
	fmXlateToFDDINovellSnapToSnapFrames	Counter
	fmXlateToFDDIEthIIToBridgeTunnelFrames	Counter
	fmXlateToFDDIEthIIToSnapFrames	Counter
	fmXlateToFDDIOtherSnapToSnapFrames	Counter
	fmXlateToFDDI8022To8022Frames	Counter

FmFilterEntry
SEQUENCE
	fmFilterIndex	INTEGER
	fmFilterFcsInvalidFrames	Counter
	fmFilterDataLengthFrames	Counter
	fmFilterErrorIndFrames	Counter
	fmFilterFddiFifoOverrunFrames	Counter
	fmFilterFddiInternalErrorFrames	Counter
	fmFilterNoBufferSpaceFrames	Counter
	fmFilterNoEndDelimitFrames	Counter
	fmFilterNoLlcHeaderFrames	Counter
	fmFilterSourceRouteFrames	Counter
	fmFilterNoSnapHeaderFrames	Counter
	fmFilterTooLargeFrames	Counter
	fmFilterNovellSnapFilteredFrames	Counter
	fmFilterCantFragmentFrames	Counter
	fmFilterBadIpHeaderFrames	Counter
	fmFilterRingDownDiscards	Counter
	fmFilterNovellOtherFilteredFrames	Counter

FmAtmCfgEntry
SEQUENCE
	fmAtmCfgIndex	INTEGER
	fmAtmCfgPOSTResult	INTEGER
	fmAtmCfgPOSTTest	INTEGER
	fmAtmCfgPOSTLoopbackResult	INTEGER
	fmAtmCfgFramingMode	INTEGER

FmAtmRxStatEntry
SEQUENCE
	fmAtmRxStatIndex	INTEGER
	fmAtmRxControlFrames	Counter
	fmAtmRxLocalLecFrames	Counter
	fmAtmRxNoBufferDiscards	Counter
	fmAtmRxCRCErrors	Counter
	fmAtmRxFrameTooLongs	Counter
	fmAtmRxOtherDiscards	Counter
	fmAtmRxHecCellErrors	Counter

Defined Values

grandjunction		1.3.6.1.4.1.437
OBJECT IDENTIFIER

products		1.3.6.1.4.1.437.1
OBJECT IDENTIFIER

fastLink		1.3.6.1.4.1.437.1.1
OBJECT IDENTIFIER

seriesG2xx		1.3.6.1.4.1.437.1.1.2
OBJECT IDENTIFIER

esModuleBasic		1.3.6.1.4.1.437.1.1.2.1
OBJECT IDENTIFIER

esModuleSpecific		1.3.6.1.4.1.437.1.1.2.2
OBJECT IDENTIFIER

esModuleBasicInfo		1.3.6.1.4.1.437.1.1.2.1.1
OBJECT IDENTIFIER

esModuleCapacity		1.3.6.1.4.1.437.1.1.2.1.1.1
The esModuleCapacity is the number of expansion slots that are available in the unit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

esModuleInfo		1.3.6.1.4.1.437.1.1.2.1.2
OBJECT IDENTIFIER

esModuleTable		1.3.6.1.4.1.437.1.1.2.1.2.1
Table of descriptive and status information about the modules.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsModuleEntry

esModuleEntry		1.3.6.1.4.1.437.1.1.2.1.2.1.1
An entry in the table, containing information about one of the modules.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	EsModuleEntry

esModuleIndex		1.3.6.1.4.1.437.1.1.2.1.2.1.1.1
This object identifies the module for which this entry contains information. This value is never greater than esModuleCapacity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

esModuleStatus		1.3.6.1.4.1.437.1.1.2.1.2.1.1.2
Current operational status of the module. This value is the same as swPortStatus for the corresponding switched port. Possible values are: enabled : normal operation (transmit and receive) disabled-mgmt : disabled by explicit management action suspended-linkbeat : suspended due to absence of linkbeat suspended-jabber : suspended because port is jabbering suspended-violation : suspended due to a secured address violation disabled-violation : disabled due to a secured address violation suspended-not-present: there is no module inserted in the expansion slot. suspended-not-recognized: there is an unrecognized module inserted in the expansion slot. reset : the module is currently in the reset state suspended-ringdown : suspended due to a ring-down condition suspended-stp : Spanning Tree Protocol non forwarding state disabled-self-test : disabled because port fails self-test suspended-atm-lane-down: Non-trunk ATM module using LANE suspended because there is no active LANE client. suspended-no-vlan : the module is not assigned to a VLAN or the assigned VLAN does not exist. disabled-no-vlan : vlan of the module is suspended or does not exist. suspended-atm-network-down: ATM module suspended due to ATM network down, or ATM physical layer down. suspended-disl : suspended while module is negotiating trunking mode using the Dynamic Inter Switch Link protocol. The default value is enabled(1), unless POST has detected a failure on the module switch port, in which case, it is disabled-mgmt(2). Any esModuleStatus of type disabled-xxxx (except disabled-self-test) is saved across a system reset so a module may also come up with such a status.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1), disabled-mgmt(2), suspended-linkbeat(3), suspended-jabber(4), suspended-violation(5), disabled-violation(7), suspended-not-present(9), suspended-not-recognized(10), reset(11), suspended-ringdown(12), suspended-stp(13), disabled-self-test(14), enabled-degraded(15), suspended-atm-lane-down(16), suspended-no-vlan(17), disabled-no-vlan(18), suspended-atm-network-down(19), suspended-disl(20)

esModuleAdminStatus		1.3.6.1.4.1.437.1.1.2.1.2.1.1.3
By explicit management action, change the port status to either enabled : normal status (transmit and receive) disabled-mgmt: port is no longer in use. This value is the same as swPortAdminStatus for the corresponding switched port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

esModuleDescr		1.3.6.1.4.1.437.1.1.2.1.2.1.1.4
A text string which includes the full name and version identification of the module's hardware type.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

esModuleID		1.3.6.1.4.1.437.1.1.2.1.2.1.1.5
A text representation of the Cisco specified identifier for the installed module, or 'notPresent'.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..60)

esModuleVersion		1.3.6.1.4.1.437.1.1.2.1.2.1.1.6
The Cisco specified unique identification for the module version, ranging from 1 to 254.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

esModuleObjectID		1.3.6.1.4.1.437.1.1.2.1.2.1.1.7
The vendor's authoritative identification of the module. This value may be allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides a straight-forward and unambiguous means for determining what kind of group is being managed. For example, this object could take the value 1.3.6.1.4.1.4242.1.2.14 if vendor 'Flintstones, Inc.' was assigned the subtree 1.3.6.1.4.1.4242, and had assigned the identifier 1.3.6.1.4.1.4242.1.2.14 to its 'Wilma Flintstone 4-Port Fast Ethernet Plug-in Module.'
Status: mandatory	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

esModulePortCapacity		1.3.6.1.4.1.437.1.1.2.1.2.1.1.8
The number of external port attachments provided by the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

esModuleReset		1.3.6.1.4.1.437.1.1.2.1.2.1.1.9
Setting this object to reset causes the module to be forced into a reset state. The reset state is a module specific condition in which the module's packet operations will cease while the module resets to a known state.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1), noReset(2)

esModuleLastStatusChange		1.3.6.1.4.1.437.1.1.2.1.2.1.1.10
Contains the value of sysUpTime at the time that the value of the esModuleStatus object for this module last changed. A value of zero indicates that the group's operational status has not changed since the agent last restarted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

esModuleCollisionPeriods		1.3.6.1.4.1.437.1.1.2.1.2.1.1.11
Contains the count of times the firmware has toggled the front panel module collision LED from the off state to the on state. Successive reads of the counter may network management software an indication of the rate of collision activity, though an actual count of collisions is not available.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

esModuleLinkDisplayMap		1.3.6.1.4.1.437.1.1.2.1.2.1.1.12
A bit array where the presence of a particular bit indicates a lit link LED for a module port. Each octet within the value of this object specifies a set of eight link LEDs, with the first octet specifying link LEDs for ports 1 through 8, the second octet specifying link LEDs 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered LED, and the least significant bit represents the highest numbered LED. Thus, each LED is represented by a single bit within the value of this object. If that bit has a value of '1' then that LED is currently lit; the LED is not lit if its bit has a value of '0'.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

esModuleDisabledDisplayMap		1.3.6.1.4.1.437.1.1.2.1.2.1.1.13
A bit array where the presence of a particular bit indicates a lit disabled LED for a module port. Each octet within the value of this object specifies a set of eight disabled LEDs, with the first octet specifying disabled LEDs for ports 1 through 8, the second octet specifying disabled LEDs 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered LED, and the least significant bit represents the highest numbered LED. Thus, each LED is represented by a single bit within the value of this object. If that bit has a value of '1' then that LED is currently lit; the LED is not lit if its bit has a value of '0'.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

esModuleBroadcastStormBlocked		1.3.6.1.4.1.437.1.1.2.1.2.1.1.14
The current broadcast forwarding status of this module. If this module is blocked by broadcast storm control, the switch drops all broadcasts received from the module. If the module is a multi-port repeater, broadcast received from a repeater port is forwarded to all the other repeater ports in the same module. The broadcast is not forwarded other switched ports.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notBlocked(1), blocked(2)

esModuleFirmwareVersion		1.3.6.1.4.1.437.1.1.2.1.2.1.1.15
This object returns the version number of the firmware stored in FLASH memory on the module. The string has the format 'v1.00' for the FDDI module. For the ATM module, the string is longer.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

esModuleBOOTCodeVersion		1.3.6.1.4.1.437.1.1.2.1.2.1.1.16
This object returns the version number of the BOOT code stored in permanent FLASH memory on the module. The string has the format 'v1.00' for the FDDI module. For the ATM module, the string is longer.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

esModuleFlashStatus		1.3.6.1.4.1.437.1.1.2.1.2.1.1.17
A string of up to 80 characters indicating the status of the firmware stored in the module's FLASH memory. The string includes the firmware revision, the data and time of the last upgrade, the source of the upgrade, as well as the validity of the firmware. The string is in net ASCII and conforms to one of the following formats: For the FDDI module: For factory installed firmware: ' v1.00 factory installed: valid' For out-of-band upgrades: ' v1.00 written 07-22-1994 08:19:15 from serial terminal: valid' For in-band upgrades: ' v1.00 written 07-22-1994 12:19:15 from 192.009.200.200: invalid' For the ATM module, the formats are similar, but the part of the string containing the version number is longer.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

esModuleResetToFactoryDefaults		1.3.6.1.4.1.437.1.1.2.1.2.1.1.18
Setting this object to reset(2) will cause the settings on the module to revert to factory defaults. The module will then be reset by the system. The module's packet operations will cease while the module resets to a known state. A read of this object will always return the value noReset(1). Setting this object to noReset(1) has no effect.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noReset(1), reset(2)

esModuleSwPortIndex		1.3.6.1.4.1.437.1.1.2.1.2.1.1.19
This is the value of swPortIndex object in the STANDALONE-ETHERNET-SWITCH-MIB corresponding to the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

esModulePortInfo		1.3.6.1.4.1.437.1.1.2.1.3
OBJECT IDENTIFIER

esModulePortTable		1.3.6.1.4.1.437.1.1.2.1.3.1
Table of descriptive and status information about the individual ports in a module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EsModulePortEntry

esModulePortEntry		1.3.6.1.4.1.437.1.1.2.1.3.1.1
An entry in the table, containing information about one of the repeater ports.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	EsModulePortEntry

esModuleSlotIndex		1.3.6.1.4.1.437.1.1.2.1.3.1.1.1
This is the value of esModuleIndex object of the module which this port belongs to. This value is never greater than esModuleCapacity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

esModulePortIndex		1.3.6.1.4.1.437.1.1.2.1.3.1.1.2
This object identifies the port for which this entry contains information. This value is never greater than esModulePortCapacity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

esModulePortDescr		1.3.6.1.4.1.437.1.1.2.1.3.1.1.3
A descriptive string of up to 60 characters used by the network administrator to name the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..60)

esModulePortAdminStatus		1.3.6.1.4.1.437.1.1.2.1.3.1.1.4
By explicit management action, change the port status to either enabled : normal status (transmit and receive) disabled : the port neither transmits nor receives. Once disabled, a port must be explicitly enabled to restore operation.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

esModulePortAutoPartitionState		1.3.6.1.4.1.437.1.1.2.1.3.1.1.5
Indicates whether the port is currently partitioned by the repeater's auto-partition protection.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAutoPartitioned(1), autoPartitioned(2)

esModulePortOperStatus		1.3.6.1.4.1.437.1.1.2.1.3.1.1.6
Indicates the port's operational status. enabled : port is enabled and working notOperational : the port neither transmits nor receives suspended-not-present: the module group is not installed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2), suspended-not-present(3)

esModulePortLinkbeatStatus		1.3.6.1.4.1.437.1.1.2.1.3.1.1.7
The port's current linkbeat status.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	linkbeat(1), noLinkbeat(2)

esModulePortConnectorType		1.3.6.1.4.1.437.1.1.2.1.3.1.1.8
The connector type for the port. It is one of other : none of the following (unknown) rj45 : common unshielded twisted pair connector bnc : thin-coax (BNC) aui : thick-coax (AUI) fiber-sc : fiber fast ethernet connector fiber-st : fiber fast ethernet connector empty : the port is not installed fddi-mic : FDDI fiber optic connector.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), rj45(2), bnc(3), aui(4), fiber-sc(5), fiber-st(6), empty(7), fddi-mic(8)

esModulePortReceivePeriods		1.3.6.1.4.1.437.1.1.2.1.3.1.1.9
Contains the count of times the front panel port receive activity LED has been toggled from the off state to the on state. Successive reads of this counter give network management software an indication of receive activity for each individual port, though an actual count of receives per port is not available.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFDDIBasic		1.3.6.1.4.1.437.1.1.2.2.1
OBJECT IDENTIFIER

fmFDDICfgInfo		1.3.6.1.4.1.437.1.1.2.2.1.1
OBJECT IDENTIFIER

fmCfgTable		1.3.6.1.4.1.437.1.1.2.2.1.1.1
Table of configuration and status information about FDDI modules.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FmCfgEntry

fmCfgEntry		1.3.6.1.4.1.437.1.1.2.2.1.1.1.1
An entry in the table, containing information about one a FDDI module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FmCfgEntry

fmCfgIndex		1.3.6.1.4.1.437.1.1.2.2.1.1.1.1.1
This object identifies the module for which this entry contains information. This value is never greater than esModuleCapacity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

fmCfgFirmwareVersion		1.3.6.1.4.1.437.1.1.2.2.1.1.1.1.2
This object returns the version number of the firmware stored in FLASH memory on the FDDI module. The string has the format 'v1.00'.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..10)

fmCfgBOOTCodeVersion		1.3.6.1.4.1.437.1.1.2.2.1.1.1.1.3
This object returns the version number of the BOOT code stored in permanent FLASH memory on the FDDI module. The string has the format 'v1.00'.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..10)

fmCfgPOSTResult		1.3.6.1.4.1.437.1.1.2.2.1.1.1.1.4
This object indicates the result of the FDDI module's Power On Self Test (POST). If the module passed POST, this item will return noFailure(1).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noFailure(1), prom(2), cpu(3), flash(4), dram(5), arbiter(6), shared-ram(7), ethernet(8), fddi-mac(9), fddi-phy-a(10), fddi-phy-b(11), packet-ram(12)

fmCfgPOSTTest		1.3.6.1.4.1.437.1.1.2.2.1.1.1.1.5
This object indicates the specific test that caused the POST to fail. If the module passed POST, this item will return noFailure(1).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noFailure(1), invalid-marker(2), checksum(3), ram-quick-scan(4), ram-byte-test(5), checkerboard(6), arbiter-id(7), read-only-register(8), read-write-register(9), ethernet-interrupt(10), loopback(11), invalid-version(12)

fmCfgPOSTLoopbackResult		1.3.6.1.4.1.437.1.1.2.2.1.1.1.1.6
In the event that the FDDI module fails the loopback test during POST, this object will indicate which portion of the test caused the failure. If the value of fmCfgPOSTTest is anything other than loopback(11), this object will have the value noFailure(1).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noFailure(1), cannot-transmit(2), receive-timeout(3), data-mismatch(4), length-mismatch(5), receiver-error(6), buffer-error(7)

fmCfgFlashStatus		1.3.6.1.4.1.437.1.1.2.2.1.1.1.1.7
A string of up to 80 characters indicating the status of the firmware stored in the FDDI module's FLASH memory. The string includes the firmware revision, the data and time of the last upgrade, the source of the upgrade, as well as the validity of the firmware. The string is in net ASCII and conforms to one of the following formats: For factory installed firmware: ' v1.00 factory installed: valid' For out-of-band upgrades: ' v1.00 written 07-22-1994 08:19:15 from serial terminal: valid' For in-band upgrades: ' v1.00 written 07-22-1994 12:19:15 from 192.009.200.200: invalid'
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

fmCfgResetToFactoryDefaults		1.3.6.1.4.1.437.1.1.2.2.1.1.1.1.8
Setting this object to reset(2) will cause the settings on the FDDI module to revert to factory defaults. The module will then be reset by the system. The module's packet operations will cease while the module resets to a known state.A read of this object will always return the value noReset(1). Setting this object to noReset(1) has no effect.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noReset(1), reset(2)

fmCfgResetModule		1.3.6.1.4.1.437.1.1.2.2.1.1.1.1.9
Setting this object to reset(2) causes the module to be forced into a reset state. During the reset state, the module's packet operations will cease while the module resets to a known state.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noReset(1), reset(2)

fmCfgNovellFDDISNAPTranslation		1.3.6.1.4.1.437.1.1.2.2.1.1.1.1.10
This object specifies the Ethernet frame type that the FDDI module will translate Novell SNAP FDDI frames into. automatic(1): the FDDI module will automatically learn which frame type to use ethernet-8023(2): the FDDI module will convert Novell SNAP FDDI frames to Ethernet 802.3 ethernet-SNAP(3): the FDDI module will convert Novell SNAP FDDI frames to Ethernet SNAP ethernet-II(4): the FDDI module will convert Novell SNAP FDDI frames to Ethernet II drop(5): the FDDI module will not forward Novell SNAP FDDI frames to Ethernet.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	automatic(1), ethernet-8023(2), ethernet-SNAP(3), ethernet-II(4), drop(5)

fmCfgUnmatchedSNAPDestination		1.3.6.1.4.1.437.1.1.2.2.1.1.1.1.11
This object specifies what the FDDI module is to do with Novell SNAP FDDI frames whose destination frame type cannot be determined. The value of this object is only valid when fmCfgNovellFDDISNAPTranslation is set to automatic(1). all(1): the unmatched Novell SNAP FDDI frames will be converted into all three possible frame types. ethernet-8023(2): the unmatched Novell SNAP FDDI frames will be converted into Ethernet 802.3 ethernet-SNAP(3): the unmatched Novell SNAP FDDI frames will be converted into Ethernet SNAP ethernet-II(4): the unmatched Novell SNAP FDDI frames will be converted into Ethernet II drop: the FDDI module will not forward unmatched Novell SNAP FDDI frames to Ethernet.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	all(1), ethernet-8023(2), ethernet-SNAP(3), ethernet-II(4), drop(5)

fmCfgAuthorizationChecking		1.3.6.1.4.1.437.1.1.2.2.1.1.1.1.12
This object controls enabling and disabling of authorization string checking by the SMT entity. When enabled, the FDDI module will use the current authorization string to verify SMT requests from remote stations. This item is disabled by default.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

fmCfgAuthorizationString		1.3.6.1.4.1.437.1.1.2.2.1.1.1.1.13
This item specifies the string to be used in the authentication of SMT requests. The length is from 0 to 32 bytes and must be a multiple of 4 bytes. This item is only used when authorization string checking is enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

fmFDDIXlateToEthInfo		1.3.6.1.4.1.437.1.1.2.2.1.2
OBJECT IDENTIFIER

fmXlateToEthTable		1.3.6.1.4.1.437.1.1.2.2.1.2.1
Table of statistics that count the number of frames successfully forwarded from the FDDI module to the switch forwarding engine.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FmXlateToEthEntry

fmXlateToEthEntry		1.3.6.1.4.1.437.1.1.2.2.1.2.1.1
An entry in the table, containing information about a FDDI module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FmXlateToEthEntry

fmXlateToEthIndex		1.3.6.1.4.1.437.1.1.2.2.1.2.1.1.1
This object identifies the module for which this entry contains information. This value is never greater than esModuleCapacity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

fmXlateToEthNovellSnapToRaw8023Frames		1.3.6.1.4.1.437.1.1.2.2.1.2.1.1.2
This object is a count of the number of Novell SNAP FDDI frames that have been converted to Raw 802.3 Ethernet frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToEthNovellSnapToEthIIFrames		1.3.6.1.4.1.437.1.1.2.2.1.2.1.1.3
This object is a count of the number of Novell SNAP FDDI frames that have been converted to Ethernet II frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToEthNovellSnapToSnapFrames		1.3.6.1.4.1.437.1.1.2.2.1.2.1.1.4
This object is a count of the number of Novell SNAP FDDI frames that have been converted to Novell SNAP Ethernet frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToEthAppleTalkSnapToSnapFrames		1.3.6.1.4.1.437.1.1.2.2.1.2.1.1.5
This object is a count of the number of AppleTalk SNAP FDDI frames that have been converted to Novell SNAP Ethernet frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToEthIpSnapForFragmentationFrames		1.3.6.1.4.1.437.1.1.2.2.1.2.1.1.6
This object is a count of the number of IP FDDI frames that were fragmented.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToEthIpSnapFragmentedFrames		1.3.6.1.4.1.437.1.1.2.2.1.2.1.1.7
This object is a count of the number of Ethernet frames that were forwarded to the switch forwarding engine as a result of IP fragmentation.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToEthBridgeTunnelToEthIIFrames		1.3.6.1.4.1.437.1.1.2.2.1.2.1.1.8
This object is a count of the number of Bridge Tunnel FDDI frames that have been converted to Ethernet II frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToEthOtherSnapToEthIIFrames		1.3.6.1.4.1.437.1.1.2.2.1.2.1.1.9
This object is a count of the number of SNAP FDDI frames that do not fall into one of the previous SNAP FDDI categories that have been converted to Ethernet II frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToEthOtherSnapToSnapFrames		1.3.6.1.4.1.437.1.1.2.2.1.2.1.1.10
This object is a count of the number of SNAP FDDI frames that do not fall into one of the previous SNAP FDDI categories that have been converted to Ethernet SNAP frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToEth8022To8022Frames		1.3.6.1.4.1.437.1.1.2.2.1.2.1.1.11
This object is a count of the number of 802.2 FDDI frames that have been converted to Ethernet 802.2 frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFDDIXlateToFDDIInfo		1.3.6.1.4.1.437.1.1.2.2.1.3
OBJECT IDENTIFIER

fmXlateToFDDITable		1.3.6.1.4.1.437.1.1.2.2.1.3.1
Table of statistics that count the number of frames successfully forwarded from the switch forwarding engine to the FDDI ring.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FmXlateToFDDIEntry

fmXlateToFDDIEntry		1.3.6.1.4.1.437.1.1.2.2.1.3.1.1
An entry in the table, containing information about a FDDI module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FmXlateToFDDIEntry

fmXlateToFDDIIndex		1.3.6.1.4.1.437.1.1.2.2.1.3.1.1.1
This object identifies the module for which this entry contains information. This value is never greater than esModuleCapacity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

fmXlateToFDDINovellRaw8023ToSnapFrames		1.3.6.1.4.1.437.1.1.2.2.1.3.1.1.2
This object is a count of the number of Novell Raw 802.3 Ethernet frames that have been converted to SNAP FDDI frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToFDDINovellEthIIToSnapFrames		1.3.6.1.4.1.437.1.1.2.2.1.3.1.1.3
This object is a count of the number of Ethernet II frames that have been converted to SNAP FDDI frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToFDDINovellSnapToSnapFrames		1.3.6.1.4.1.437.1.1.2.2.1.3.1.1.4
This object is a count of the number of Novell SNAP Ethernet frames that have been converted to SNAP FDDI frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToFDDIEthIIToBridgeTunnelFrames		1.3.6.1.4.1.437.1.1.2.2.1.3.1.1.5
This object is a count of the number of Ethernet II frames that have been converted to Bridge Tunnel FDDI frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToFDDIEthIIToSnapFrames		1.3.6.1.4.1.437.1.1.2.2.1.3.1.1.6
This object is a count of the number of Ethernet II frames that have been converted to SNAP FDDI frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToFDDIOtherSnapToSnapFrames		1.3.6.1.4.1.437.1.1.2.2.1.3.1.1.7
This object is a count of the number of SNAP frames that do not fall into one of the above listed SNAP type categories that have been translated to Ethernet II.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmXlateToFDDI8022To8022Frames		1.3.6.1.4.1.437.1.1.2.2.1.3.1.1.8
This object is a count of the number of FDDI 802.2 frames that have been converted to Ethernet 802.2 frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFDDIFilterInfo		1.3.6.1.4.1.437.1.1.2.2.1.4
OBJECT IDENTIFIER

fmFilterTable		1.3.6.1.4.1.437.1.1.2.2.1.4.1
Table of statistics that count the number of frames that were not forwarded by the FDDI module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FmFilterEntry

fmFilterEntry		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1
An entry in the table, containing information about a FDDI module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FmFilterEntry

fmFilterIndex		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.1
This object identifies the module for which this entry contains information. This value is never greater than esModuleCapacity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

fmFilterFcsInvalidFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.2
This object is a count of the number of FDDI frames that were not forwarded because the frame contained an invalid FCS.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterDataLengthFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.3
This object is a count of the number of FDDI frames that were not forwarded because the frame contained an invalid data length.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterErrorIndFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.4
This object is a count of the number of FDDI frames that were not forwarded because the frame's error indication flag was set.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterFddiFifoOverrunFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.5
This object is a count of the number of FDDI frames that were not forwarded because the FDDI FIFO experienced an overflow.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterFddiInternalErrorFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.6
This object is a count of the number of FDDI frames that were not forwarded because the module experienced an internal error.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterNoBufferSpaceFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.7
This object is a count of the number of FDDI frames that were not forwarded because the module did not have sufficient buffer space.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterNoEndDelimitFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.8
This object is a count of the number of FDDI frames that were not forwarded because the frame did not have a valid end delimiter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterNoLlcHeaderFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.9
This object is a count of the number of FDDI frames that were not forwarded because the frame did not have a valid LLC header.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterSourceRouteFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.10
The FDDI module does not forward source routing frames. This object is a count of the number of such frames that were filtered.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterNoSnapHeaderFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.11
This object is a count of the number of FDDI frames that were not forwarded because the frame did not have a valid SNAP header.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterTooLargeFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.12
This object is a count of the number of FDDI frames that were not forwarded because the frame was too large.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterNovellSnapFilteredFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.13
This object is a count of the number of Novell SNAP FDDI frames that were filtered by the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterCantFragmentFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.14
This object is a count of the number of FDDI IP frames that were not forwarded because the module was unable to fragment the frame.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterBadIpHeaderFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.15
This object is a count of the number of FDDI frames that were not forwarded because the frame contained an invalid IP header.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterRingDownDiscards		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.16
This object is a count of the number of FDDI frames that were not forwarded because the FDDI ring was not operational.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmFilterNovellOtherFilteredFrames		1.3.6.1.4.1.437.1.1.2.2.1.4.1.1.17
This object is the sum of the Novell Ethernet frames that were not forwarded because they contained an invalid size field and the number of Novell Ethernet frames that were not forwarded because the FDDI module was configured to filter Novell SNAP FDDI frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmAtmBasic		1.3.6.1.4.1.437.1.1.2.2.2
OBJECT IDENTIFIER

fmAtmCfgInfo		1.3.6.1.4.1.437.1.1.2.2.2.1
OBJECT IDENTIFIER

fmAtmCfgTable		1.3.6.1.4.1.437.1.1.2.2.2.1.1
Table of configuration and status information about ATM modules.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FmAtmCfgEntry

fmAtmCfgEntry		1.3.6.1.4.1.437.1.1.2.2.2.1.1.1
An entry in the table, containing information about one ATM module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FmAtmCfgEntry

fmAtmCfgIndex		1.3.6.1.4.1.437.1.1.2.2.2.1.1.1.1
This object identifies the module for which this entry contains information. This value is never greater than esModuleCapacity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

fmAtmCfgPOSTResult		1.3.6.1.4.1.437.1.1.2.2.2.1.1.1.2
This object indicates the result of the ATM module's Power On Self Test (POST), that is, which module component, if any, failed POST. If the module passed POST, this item will return no-failure(2).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), unknown(2), no-failure(3), fpga(4), shared-memory(5), host-interface(6), ethernet-controller(7), sar-controller(8), sar-memory(9), framer(10), traffic-co-processor(11), traffic-co-processor-memory(12), flash(13)

fmAtmCfgPOSTTest		1.3.6.1.4.1.437.1.1.2.2.2.1.1.1.3
This object indicates the specific test that caused the POST to fail. If the ATM module passed POST, this item will return no-failure(2).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), unknown(2), no-failure(3), refresh(4), quick-scan-word(5), quick-scan-byte(6), byte-pattern(7), checkerboard(8), no-response(9), data-mismatch(10), interrupt(11), control-memory(12), checksum(13), read-only-configuration-register(14), read-write-configuration-register(15), read-only-register(16), read-write-register(17), local-loopback(18), host-loopback(19), module-to-host-interrupt(20), host-to-module-interrupt(21)

fmAtmCfgPOSTLoopbackResult		1.3.6.1.4.1.437.1.1.2.2.2.1.1.1.4
In the event that the ATM module fails a loopback test during POST, this object will indicate which portion of the test caused the failure. If the value of fmAtmCfgPOSTTest is anything other than local-loopback(17) or host-loopback(18) this object will have the value no-failure(2).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), unknown(2), no-failure(3), cannot-transmit(4), receive-timeout(5), data-mismatch(6), length-mismatch(7), receiver-error(8), buffer-error(9)

fmAtmCfgFramingMode		1.3.6.1.4.1.437.1.1.2.2.2.1.1.1.5
The mode of operation for the SONET PLIM. The default value is sts-3c(1).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	sts-3c(1), stm-1(2)

fmAtmStatsInfo		1.3.6.1.4.1.437.1.1.2.2.2.2
OBJECT IDENTIFIER

fmAtmRxStatTable		1.3.6.1.4.1.437.1.1.2.2.2.2.1
Table of receive statistics on ATM modules.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FmAtmRxStatEntry

fmAtmRxStatEntry		1.3.6.1.4.1.437.1.1.2.2.2.2.1.1
An entry in the table, containing receive statistics about one ATM module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FmAtmRxStatEntry

fmAtmRxStatIndex		1.3.6.1.4.1.437.1.1.2.2.2.2.1.1.1
This object identifies the module for which this entry contains information. This value is never greater than esModuleCapacity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

fmAtmRxControlFrames		1.3.6.1.4.1.437.1.1.2.2.2.2.1.1.2
A count of number of AAL5 control frames received by the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmAtmRxLocalLecFrames		1.3.6.1.4.1.437.1.1.2.2.2.2.1.1.3
A count of AAL5 frames received with LEC ids matching the module's LEC id. These frames are discarded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmAtmRxNoBufferDiscards		1.3.6.1.4.1.437.1.1.2.2.2.2.1.1.4
A count of AAL5 frames received that were discarded due to a lack of frame buffer resources in the module's forwarding engine.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmAtmRxCRCErrors		1.3.6.1.4.1.437.1.1.2.2.2.2.1.1.5
A count of AAL5 frames received that were discarded due to CRC errors.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmAtmRxFrameTooLongs		1.3.6.1.4.1.437.1.1.2.2.2.2.1.1.6
A count of AAL5 frames received that exceed the maximum permitted frame size as defined by ifMtu object the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmAtmRxOtherDiscards		1.3.6.1.4.1.437.1.1.2.2.2.2.1.1.7
A count of AAL5 frames received that were discarded due to reasons other than a lack of frame buffer resources in the module's forwarding engine, errors, frames exceeding maximum frame size, or frames with LEC id matching the module's LEC id.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

fmAtmRxHecCellErrors		1.3.6.1.4.1.437.1.1.2.2.2.2.1.1.8
A count of ATM cells received with errors in HEC header.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter