ES1200-MIB

File: ES1200-MIB.mib (155214 bytes)

Imported modules

RFC-1212 RFC1155-SMI RFC-1215
BRIDGE-MIB RFC1213-MIB

Imported symbols

OBJECT-TYPE enterprises IpAddress
TRAP-TYPE Counter TimeTicks
dot1dBasePort MacAddress DisplayString

Defined Types

PortList  
OCTET STRING Size(12)    

VlanIndex  
INTEGER 1..4094    

SwStructUnitEntry  
SEQUENCE    
  swStructUnitIndex INTEGER
  swStructUnitType OBJECT IDENTIFIER
  swStructUnitDescr DisplayString Size(0..64)
  swStructUnitLedInfo OCTET STRING Size(0..7)
  swStructUnitMaxModuleNum INTEGER
  swStructUnitMaxPortNum INTEGER
  swStructUnitNumOfPortInUse INTEGER
  swStructUnitOperStatus INTEGER
  swStructUnitLastChange INTEGER

SwStructModuleEntry  
SEQUENCE    
  swStructModuleUnitIndex INTEGER
  swStructModuleIndex INTEGER
  swStructModuleSubMduIndex INTEGER
  swStructModuleType OBJECT IDENTIFIER
  swStructModuleDescr DisplayString Size(0..64)
  swStructModuleVersion INTEGER
  swStructModuleMaxPortNum INTEGER
  swStructModuleEncodingOffset INTEGER
  swStructModuleOperStatus INTEGER
  swStructModuleLastChange INTEGER

SwStructPowerEntry  
SEQUENCE    
  swStructPowerUnitIndex INTEGER
  swStructPowerIndex INTEGER
  swStructPowerOperStatus INTEGER

SwStructFanEntry  
SEQUENCE    
  swStructFanUnitIndex INTEGER
  swStructFanIndex INTEGER
  swStructFanOperStatus INTEGER

SwFdbStaticEntry  
SEQUENCE    
  swFdbStaticVid INTEGER
  swFdbStaticAddress MacAddress
  swFdbStaticPortMap PortList
  swFdbStaticJoinIGMPSnooping INTEGER
  swFdbStaticState INTEGER
  swFdbStaticStatus INTEGER

SwFdbStaticMemberEntry  
SEQUENCE    
  swFdbStaticMemberVid INTEGER
  swFdbStaticMemberAddress MacAddress
  swFdbStaticMemberUnitIndex INTEGER
  swFdbStaticMemberModuleIndex INTEGER
  swFdbStaticMemberPortIndex INTEGER

SwFdbFilterEntry  
SEQUENCE    
  swFdbFilterVid INTEGER
  swFdbFilterAddress MacAddress
  swFdbFilterState INTEGER

SwL2PortInfoEntry  
SEQUENCE    
  swL2PortInfoUnitIndex INTEGER
  swL2PortInfoModuleIndex INTEGER
  swL2PortInfoIndex INTEGER
  swL2PortInfoType INTEGER
  swL2PortInfoDescr DisplayString Size(0..64)
  swL2PortInfoLinkStatus INTEGER
  swL2PortInfoNwayStatus INTEGER

SwL2PortCtrlEntry  
SEQUENCE    
  swL2PortCtrlUnitIndex INTEGER
  swL2PortCtrlModuleIndex INTEGER
  swL2PortCtrlIndex INTEGER
  swL2PortCtrlAdminState INTEGER
  swL2PortCtrlLinkStatusAlarmState INTEGER
  swL2PortCtrlNwayState INTEGER
  swL2PortCtrlFlowCtrlState INTEGER
  swL2PortCtrlBackPressState INTEGER
  swL2PortCtrlLockState INTEGER
  swL2PortCtrlPriority INTEGER
  swL2PortCtrlStpState INTEGER
  swL2PortCtrlHOLState INTEGER
  swL2PortCtrlBcastRisingAct INTEGER
  swL2PortCtrlBcastFallingAct INTEGER

SwL2PortStEntry  
SEQUENCE    
  swL2PortStUnitIndex INTEGER
  swL2PortStModuleIndex INTEGER
  swL2PortStIndex INTEGER
  swL2PortStByteRx Counter
  swL2PortStByteTx Counter
  swL2PortStFrameRx Counter
  swL2PortStFrameTx Counter
  swL2PortStTotalBytesRx Counter
  swL2PortStTotalFramesRx Counter
  swL2PortStBroadcastFramesRx Counter
  swL2PortStMulticastFramesRx Counter
  swL2PortStCRCError Counter
  swL2PortStOversizeFrames Counter
  swL2PortStFragments Counter
  swL2PortStJabber Counter
  swL2PortStCollision Counter
  swL2PortStLateCollision Counter
  swL2PortStFrames-64-bytes Counter
  swL2PortStFrames-65-127-bytes Counter
  swL2PortStFrames-128-255-bytes Counter
  swL2PortStFrames-256-511-bytes Counter
  swL2PortStFrames-512-1023-bytes Counter
  swL2PortStFrames-1024-1536-bytes Counter
  swL2PortStFramesDroppedFrames Counter
  swL2PortStMulticastFramesTx Counter
  swL2PortStBroadcastFramesTx Counter
  swL2PortStUndersizeFrames Counter

SwIGMPInfoEntry  
SEQUENCE    
  swIGMPInfoIndex INTEGER
  swIGMPInfoVid INTEGER
  swIGMPInfoQueryCount INTEGER
  swIGMPInfoTxQueryCount INTEGER

SwIGMPEntry  
SEQUENCE    
  swIGMPVid INTEGER
  swIGMPGroupIpAddr IpAddress
  swIGMPGroupMacAddr MacAddress
  swIGMPPortMap PortList
  swIGMPIpGroupReportCount INTEGER

SwIGMPCtrlEntry  
SEQUENCE    
  swIGMPCtrlIndex INTEGER
  swIGMPCtrlVid INTEGER 1..4094
  swIGMPCtrlTimer INTEGER
  swIGMPCtrlState INTEGER

EnabledStatus  
INTEGER enabled(1), disabled(2)    

TruthValue  
INTEGER true(1), false(2)    

TimeInterval  
INTEGER    

Dot1dPortCapabilitiesEntry  
SEQUENCE    
  dot1dPortCapabilities INTEGER

Dot1dPortPriorityEntry  
SEQUENCE    
  dot1dPortNumTrafficClasses INTEGER

Dot1dPortGarpEntry  
SEQUENCE    
  dot1dPortGarpJoinTime TimeInterval
  dot1dPortGarpLeaveTime TimeInterval
  dot1dPortGarpLeaveAllTime TimeInterval

Dot1dPortGmrpEntry  
SEQUENCE    
  dot1dPortGmrpStatus EnabledStatus
  dot1dPortGmrpFailedRegistrations Counter
  dot1dPortGmrpLastPduOrigin MacAddress

Unsigned32  
INTEGER    

VlanId  
INTEGER 1..4094    

TimeFilter  
INTEGER    

Dot1qFdbEntry  
SEQUENCE    
  dot1qFdbId Unsigned32
  dot1qFdbDynamicCount Counter

Dot1qTpFdbEntry  
SEQUENCE    
  dot1qTpFdbAddress MacAddress
  dot1qTpFdbPort INTEGER
  dot1qTpFdbStatus INTEGER

Dot1qTpGroupEntry  
SEQUENCE    
  dot1qTpGroupAddress MacAddress
  dot1qTpGroupEgressPorts PortList
  dot1qTpGroupLearnt PortList

Dot1qStaticMulticastEntry  
SEQUENCE    
  dot1qStaticMulticastAddress MacAddress
  dot1qStaticMulticastReceivePort INTEGER
  dot1qStaticMulticastStaticEgressPorts PortList
  dot1qStaticMulticastForbiddenEgressPorts PortList
  dot1qStaticMulticastStatus INTEGER

Dot1qVlanCurrentEntry  
SEQUENCE    
  dot1qVlanTimeMark TimeFilter
  dot1qVlanIndex VlanIndex
  dot1qVlanFdbId Unsigned32
  dot1qVlanCurrentEgressPorts PortList
  dot1qVlanCurrentUntaggedPorts PortList
  dot1qVlanStatus INTEGER
  dot1qVlanCreationTime TimeTicks

Dot1qVlanStaticEntry  
SEQUENCE    
  dot1qVlanStaticName DisplayString
  dot1qVlanStaticEgressPorts PortList
  dot1qVlanForbiddenEgressPorts PortList
  dot1qVlanStaticUntaggedPorts PortList
  dot1qVlanStaticRowState INTEGER

Dot1qPortVlanEntry  
SEQUENCE    
  dot1qPvid VlanIndex
  dot1qPortIngressFiltering TruthValue
  dot1qPortGvrpStatus EnabledStatus
  dot1qPortGvrpFailedRegistrations Counter
  dot1qPortGvrpLastPduOrigin MacAddress

SwSniffCtrlEntry  
SEQUENCE    
  swSniffIndex INTEGER
  swSniffSourcePort INTEGER
  swSniffTargetPort INTEGER
  swSniffState INTEGER

SwPortTrunkCtrlEntry  
SEQUENCE    
  swPortTrunkCtrlIndex INTEGER
  swPortTrunkCtrlAnchorPort INTEGER
  swPortTrunkCtrlMasterPort INTEGER
  swPortTrunkCtrlName DisplayString Size(0..16)
  swPortTrunkCtrlMember PortList
  swPortTrunkCtrlState INTEGER

SwPortTrunkMemberEntry  
SEQUENCE    
  swPortTrunkMemberIndex INTEGER
  swPortTrunkMemberUnitIndex INTEGER
  swPortTrunkMemberModuleIndex INTEGER
  swPortTrunkMemberPortIndex INTEGER

SwMacBaseVlanCtrlEntry  
SEQUENCE    
  swMacBaseVlanDesc DisplayString Size(1..12)
  swMacBaseVlanMacMember INTEGER
  swMacBaseVlanCtrlState INTEGER

SwMacBaseVlanAddrEntry  
SEQUENCE    
  swMacBaseVlanAddr MacAddress
  swMacBaseVlanAddrVlanDesc DisplayString Size(1..64)
  swMacBaseVlanAddrState INTEGER
  swMacBaseVlanAddrStatus INTEGER

SwPortBaseVlanDefaultVlanEntry  
SEQUENCE    
  swPortBaseVlanDefaultPvid INTEGER
  swPortBaseVlanDefaultDesc DisplayString
  swPortBaseVlanDefaultPortList PortList
  swPortBaseVlanDefaultPortNumber INTEGER

SwPortBaseVlanConfigEntry  
SEQUENCE    
  swPortBaseVlanConfigPvid INTEGER
  swPortBaseVlanConfigDesc DisplayString
  swPortBaseVlanConfigPortList PortList
  swPortBaseVlanConfigPortNumber INTEGER

Defined Values

fore 1.3.6.1.4.1.326
OBJECT IDENTIFIER    

systems 1.3.6.1.4.1.326.2
OBJECT IDENTIFIER    

ethernet 1.3.6.1.4.1.326.2.20
OBJECT IDENTIFIER    

edge 1.3.6.1.4.1.326.2.20.1
OBJECT IDENTIFIER    

edgecommon 1.3.6.1.4.1.326.2.20.1.1
OBJECT IDENTIFIER    

golf 1.3.6.1.4.1.326.2.20.1.2
OBJECT IDENTIFIER    

golfproducts 1.3.6.1.4.1.326.2.20.1.2.1
OBJECT IDENTIFIER    

es1200 1.3.6.1.4.1.326.2.20.1.2.1.2
OBJECT IDENTIFIER    

golfcommon 1.3.6.1.4.1.326.2.20.1.2.2
OBJECT IDENTIFIER    

fore-products 1.3.6.1.4.1.326.2.20.1.2.2.1
OBJECT IDENTIFIER    

fore-es1200Prod 1.3.6.1.4.1.326.2.20.1.2.2.1.25
OBJECT IDENTIFIER    

swProperty 1.3.6.1.4.1.326.2.20.1.2.2.1.25.1
OBJECT IDENTIFIER    

swModule 1.3.6.1.4.1.326.2.20.1.2.2.1.25.1.1
OBJECT IDENTIFIER    

es1200DevRegistration 1.3.6.1.4.1.326.2.20.1.2.2.1.25.2
OBJECT IDENTIFIER    

es1200Device 1.3.6.1.4.1.326.2.20.1.2.2.1.25.2.1
OBJECT IDENTIFIER    

es1200UnitRegistration 1.3.6.1.4.1.326.2.20.1.2.2.1.25.3
OBJECT IDENTIFIER    

es1200Master 1.3.6.1.4.1.326.2.20.1.2.2.1.25.3.1
OBJECT IDENTIFIER    

es1210Slave1 1.3.6.1.4.1.326.2.20.1.2.2.1.25.3.2
OBJECT IDENTIFIER    

es1210Slave2 1.3.6.1.4.1.326.2.20.1.2.2.1.25.3.3
OBJECT IDENTIFIER    

es1210Slave3 1.3.6.1.4.1.326.2.20.1.2.2.1.25.3.4
OBJECT IDENTIFIER    

es1200ModuleRegistration 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4
OBJECT IDENTIFIER    

es1200ModuleMainboardTx 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.1
OBJECT IDENTIFIER    

es1200ModuleTxTwoPort 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.2
OBJECT IDENTIFIER    

es1200ModuleFxSC 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.3
OBJECT IDENTIFIER    

es1200ModuleFxMTRJ 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.4
OBJECT IDENTIFIER    

es1200ModuleSIO 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.5
OBJECT IDENTIFIER    

es1200ModuleSXGIGAOnePort 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.6
OBJECT IDENTIFIER    

es1200ModuleSXGIGATwoPort 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.7
OBJECT IDENTIFIER    

es1200ModuleLXGIGAOnePort 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.8
OBJECT IDENTIFIER    

es1200ModuleLXGIGATwoPort 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.9
OBJECT IDENTIFIER    

es1200ModuleTXGIGAOnePort 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.10
OBJECT IDENTIFIER    

es1200ModuleTXGIGATwoPort 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.11
OBJECT IDENTIFIER    

es1200ModuleNone 1.3.6.1.4.1.326.2.20.1.2.2.1.25.4.12
OBJECT IDENTIFIER    

es1210ModuleRegistration 1.3.6.1.4.1.326.2.20.1.2.2.1.25.5
OBJECT IDENTIFIER    

es1210ModuleMainboardTx 1.3.6.1.4.1.326.2.20.1.2.2.1.25.5.1
OBJECT IDENTIFIER    

es1210ModuleTxTwoPort 1.3.6.1.4.1.326.2.20.1.2.2.1.25.5.2
OBJECT IDENTIFIER    

es1210ModuleFxSC 1.3.6.1.4.1.326.2.20.1.2.2.1.25.5.3
OBJECT IDENTIFIER    

es1210ModuleFxMTRJ 1.3.6.1.4.1.326.2.20.1.2.2.1.25.5.4
OBJECT IDENTIFIER    

es1210ModuleSIO 1.3.6.1.4.1.326.2.20.1.2.2.1.25.5.5
OBJECT IDENTIFIER    

es1210ModuleNone 1.3.6.1.4.1.326.2.20.1.2.2.1.25.5.6
OBJECT IDENTIFIER    

es1200PortRegistration 1.3.6.1.4.1.326.2.20.1.2.2.1.25.6
OBJECT IDENTIFIER    

es1200Port-10-100TX 1.3.6.1.4.1.326.2.20.1.2.2.1.25.6.1
OBJECT IDENTIFIER    

es1200Port-100-SC 1.3.6.1.4.1.326.2.20.1.2.2.1.25.6.2
OBJECT IDENTIFIER    

es1200Port-100-MTRJ 1.3.6.1.4.1.326.2.20.1.2.2.1.25.6.3
OBJECT IDENTIFIER    

es1200Port-1000-SX 1.3.6.1.4.1.326.2.20.1.2.2.1.25.6.4
OBJECT IDENTIFIER    

es1200Port-1000-LX 1.3.6.1.4.1.326.2.20.1.2.2.1.25.6.5
OBJECT IDENTIFIER    

es1200Port-1000-TX 1.3.6.1.4.1.326.2.20.1.2.2.1.25.6.6
OBJECT IDENTIFIER    

es1210PortRegistration 1.3.6.1.4.1.326.2.20.1.2.2.1.25.7
OBJECT IDENTIFIER    

es1210Port-10-100TX 1.3.6.1.4.1.326.2.20.1.2.2.1.25.7.1
OBJECT IDENTIFIER    

es1210Port-100-SC 1.3.6.1.4.1.326.2.20.1.2.2.1.25.7.2
OBJECT IDENTIFIER    

es1210Port-100-MTRJ 1.3.6.1.4.1.326.2.20.1.2.2.1.25.7.3
OBJECT IDENTIFIER    

es1200PowerSupplyRegistration 1.3.6.1.4.1.326.2.20.1.2.2.1.25.8
OBJECT IDENTIFIER    

es1200PowerSupply 1.3.6.1.4.1.326.2.20.1.2.2.1.25.8.1
OBJECT IDENTIFIER    

es1210PowerSupplyRegistration 1.3.6.1.4.1.326.2.20.1.2.2.1.25.9
OBJECT IDENTIFIER    

es1210PowerSupply 1.3.6.1.4.1.326.2.20.1.2.2.1.25.9.1
OBJECT IDENTIFIER    

es1200FanRegistration 1.3.6.1.4.1.326.2.20.1.2.2.1.25.10
OBJECT IDENTIFIER    

es1200Fan 1.3.6.1.4.1.326.2.20.1.2.2.1.25.10.1
OBJECT IDENTIFIER    

es1210FanRegistration 1.3.6.1.4.1.326.2.20.1.2.2.1.25.11
OBJECT IDENTIFIER    

es1210Fan 1.3.6.1.4.1.326.2.20.1.2.2.1.25.11.1
OBJECT IDENTIFIER    

es1200SlotRegistration 1.3.6.1.4.1.326.2.20.1.2.2.1.25.12
OBJECT IDENTIFIER    

es1200Slot1 1.3.6.1.4.1.326.2.20.1.2.2.1.25.12.1
OBJECT IDENTIFIER    

es1200Slot2 1.3.6.1.4.1.326.2.20.1.2.2.1.25.12.2
OBJECT IDENTIFIER    

es1200Slot3 1.3.6.1.4.1.326.2.20.1.2.2.1.25.12.3
OBJECT IDENTIFIER    

es1210SlotRegistration 1.3.6.1.4.1.326.2.20.1.2.2.1.25.13
OBJECT IDENTIFIER    

es1210Slot1 1.3.6.1.4.1.326.2.20.1.2.2.1.25.13.1
OBJECT IDENTIFIER    

es1210Slot2 1.3.6.1.4.1.326.2.20.1.2.2.1.25.13.2
OBJECT IDENTIFIER    

es1200SensorRegistration 1.3.6.1.4.1.326.2.20.1.2.2.1.25.14
OBJECT IDENTIFIER    

es1200BackplaneRegistration 1.3.6.1.4.1.326.2.20.1.2.2.1.25.15
OBJECT IDENTIFIER    

fore-mgmt 1.3.6.1.4.1.326.2.20.1.2.2.2
OBJECT IDENTIFIER    

es1200Mgmt 1.3.6.1.4.1.326.2.20.1.2.2.2.25
OBJECT IDENTIFIER    

swL2Mgmt 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2
OBJECT IDENTIFIER    

swStructure 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1
OBJECT IDENTIFIER    

swStructInfo 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.1
OBJECT IDENTIFIER    

swStructDevType 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.1.1
Specifies the device type
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

swStructDevDescr 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.1.2
Describes the type of the device
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

swStructPortEncodingFactor 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.1.3
The factor to encode the global port ID from unit ID and the local port ID. This global port ID is required to access the bridge MIB and spanning tree MIB defined by the standard body. This global port ID will provide a unigue port ID for each port across the entire device. Example: supoposed that the encoding factor is 24, then port 2 located on unit 2 will be encoded as port 26
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructUnitTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2
A table that contains information about a unit in the device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwStructUnitEntry

swStructUnitEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1
A list of information for each unit in the device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwStructUnitEntry  

swStructUnitIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.1
ID of the unit in the device
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructUnitType 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.2
Type of the unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

swStructUnitDescr 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.3
Type of the unit in displayed string format
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

swStructUnitLedInfo 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.4
Provides the LED information for the unit. Master: byte 0: bit 0:Condole in Use (0:not used,1:used) bit 1:Giga module status (0:not exist,1:exist) bit 2:Giga module port1 status (0:link fail,1:link pass) bit 3:Giga module port2 status (0:link fail,1:link pass) bit 4:Slot2 module status (0:not exist,1:exist) bit 5:Unit slave1 status (0:not exist,1:exist) bit 6:Unit slave2 status (0:not exist,1:exist) bit 7:Unit slave3 status (0:not exist,1:exist) byte 1: bit 0:Slot1 module port1 nway status (0:10M,1:100M) bit 1:Slot1 module port1 link status (0:link fail,1:link pass) bit 2:Slot1 module port2 nway status (0:10M,1:100M) bit 3:Slot1 module port2 link status (0:link fail,1:link pass) bit 4:Base module port1 nway status (0:10M,1:100M) bit 5:Base module port1 link status (0:link fail,1:link pass) bit 6:Base module port2 nway status (0:10M,1:100M) bit 7:Base module port2 link status (0:link fail,1:link pass) byte 2: bit 0:Base module port3 nway status (0:10M,1:100M) bit 1:Base module port3 link status (0:link fail,1:link pass) bit 2:Base module port4 nway status (0:10M,1:100M) bit 3:Base module port4 link status (0:link fail,1:link pass) bit 4:Base module port5 nway status (0:10M,1:100M) bit 5:Base module port5 link status (0:link fail,1:link pass) bit 6:Base module port6 nway status (0:10M,1:100M) bit 7:Base module port6 link status (0:link fail,1:link pass) byte 3: ... . . byte 7: ... Slave: byte 0: bit 0:Not used bit 1:Not used bit 2:Not used bit 3:Not used bit 4:Slot2 module status (0:not exist,1:exist) bit 5:Unit slave1 status (0:not exist,1:exist) bit 6:Unit slave2 status (0:not exist,1:exist) bit 7:Unit slave3 status (0:not exist,1:exist) byte 1: bit 0:Slot1 module port1 nway status (0:10M,1:100M) bit 1:Slot1 module port1 link status (0:link fail,1:link pass) bit 2:Slot1 module port2 nway status (0:10M,1:100M) bit 3:Slot1 module port2 link status (0:link fail,1:link pass) bit 4:Base module port1 nway status (0:10M,1:100M) bit 5:Base module port1 link status (0:link fail,1:link pass) bit 6:Base module port2 nway status (0:10M,1:100M) bit 7:Base module port2 link status (0:link fail,1:link pass) byte 2: ... . . byte 7: ...
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..7)  

swStructUnitMaxModuleNum 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.5
Maximum number of modules allowed on the unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructUnitMaxPortNum 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.6
Maximum number of ports allowed on the unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructUnitNumOfPortInUse 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.7
Number of ports which has link being connected to the port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructUnitOperStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.8
Describes the operation status for the unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), notAvail(2), removed(3), disabled(4), normal(5), nonFatalErr(9), fatalErr(10)  

swStructUnitLastChange 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.2.1.9
Provides the time that the unit is up last time
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructModuleTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3
A table that contains information about a module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwStructModuleEntry

swStructModuleEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1
A list of information for a module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwStructModuleEntry  

swStructModuleUnitIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.1
ID of the unit in the device
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructModuleIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.2
ID of the Module in the device
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructModuleSubMduIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.3
If the module doesnot contain sub module, sub module ID is 0. Otherwise, it indicates the ID of the sub module relative to the module
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructModuleType 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.4
Type of the module
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

swStructModuleDescr 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.5
Type of the module in displayed string format
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

swStructModuleVersion 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.6
Provides PCB version of the module
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructModuleMaxPortNum 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.7
Maximum number of ports allowed on the module
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructModuleEncodingOffset 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.8
Each module has a offset for encoding the port ID relative to a unit. This encoding will provide a unigue port ID for ports located on the device. Example: supoposed that the offset for module 2 is 21, then port 2 located on module 2 will be encoded as port 22
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructModuleOperStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.9
Provides operation status of the module
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), notAvail(2), removed(3), disabled(4), normal(5), nonFatalErr(9), fatalErr(10)  

swStructModuleLastChange 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.3.1.10
Provides the time that the module is up last time
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructPowerTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.4
A table that contains information about every board.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwStructPowerEntry

swStructPowerEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.4.1
A list of information for each board of the chassis.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwStructPowerEntry  

swStructPowerUnitIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.4.1.1
ID of the unit in the device
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructPowerIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.4.1.2
ID of the power supply in the unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructPowerOperStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.4.1.3
Describes the operation status of the power supply
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), notAvail(2), removed(3), disabled(4), normal(5), nonFatalErr(9), fatalErr(10)  

swStructFanTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.5
A table that contains information about every board.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwStructFanEntry

swStructFanEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.5.1
A list of information for each board of the chassis.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwStructFanEntry  

swStructFanUnitIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.5.1.1
ID of the unit in the device
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructFanIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.5.1.2
ID of the fan in the device
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swStructFanOperStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.1.5.1.3
Describes the operation status of the fan
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), notAvail(2), removed(3), disabled(4), normal(5), nonFatalErr(9), fatalErr(10)  

swFDB 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9
OBJECT IDENTIFIER    

endOfMIB 1.3.6.1.4.1.326.2.20.1.2.2.2.25.9999
Tok_String
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

swFdbStaticTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1
This table defines for frames with specific destincation MAC address, the set of ports that the frame will be forwarded to. Note that if a MAC address appears in this table also appears in the filter table, the filter table has higher priority over than this table. See swFdbFilterTable description.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwFdbStaticEntry

swFdbStaticEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1.1
A list of information specifies which ports the frames with specific destination MAC address to go.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwFdbStaticEntry  

swFdbStaticVid 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1.1.1
This object indicates the VLAN-ID. If the swVlanInfoStatus is port-base mode , the object ranges from 1 to 12. If VLAN is in mac-based mode or disabled, the object indicates the default VLAN-ID(0).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swFdbStaticAddress 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1.1.2
The MAC address which this forwarding entry applied. It can be an unicast address or a multicast address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  MacAddress  

swFdbStaticPortMap 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1.1.3
The set of ports to which frames received containing the value of swFdbStaticAddress as the DA, are allowed to be forwarded. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant.)
Status: mandatory Access: read-write
OBJECT-TYPE    
  PortList  

swFdbStaticJoinIGMPSnooping 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1.1.4
This object indicates whether to allow ports to join/leave IGMP group via IGMP Snooping. For a multicast address entry, port group could be classified into two catelogies : one is static and another is dynamic. In static port group, port members is defined statically by user, and dynamic port group allows a port member to join/leave the membership dynamically, according to IGMP report/leave messages. When this object is set to 'enabled', it allows dynamic port group updated for the multicast address entry as well as static port group. When it is set to 'disabled' , dynamic port member join/leave is disabled, but static port group is not affected. This object is only vaild for multicast address indicated by swFdbStaticAddressIndex. It always is 'disabled' for unicast addresses. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - this entry doesn't allow dynamic updates via IGMP Snooping.This is a default setting. enabled(3) - this entry allow dynamic updates via IGMP Snooping.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swFdbStaticState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1.1.5
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

swFdbStaticStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.1.1.6
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. apply(2) - this entry is currently in use and reside in the table. not-apply(3) - this entry is reside in the table but currently not in use due to conflict with filter table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), apply(2), not-apply(3)  

swFdbStaticMemberTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.2
A list of information provide a different view for those ports where packets from the given Vlan need to be forwarded to.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwFdbStaticMemberEntry

swFdbStaticMemberEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.2.1
A list of MIB capability entries supported by this forwarding static table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwFdbStaticMemberEntry  

swFdbStaticMemberVid 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.2.1.1
This object indicates the VLAN-ID. If the swVlanInfoStatus is port-base mode , the object ranges from 1 to 12. If VLAN is in mac-based mode or disabled, the object indicates the default VLAN-ID(0).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swFdbStaticMemberAddress 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.2.1.2
The MAC address which this forwarding entry applied. It can be an unicast address or a multicast address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  MacAddress  

swFdbStaticMemberUnitIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.2.1.3
Specifies the unit ID where the port is located
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swFdbStaticMemberModuleIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.2.1.4
Specifies the module ID where the port is located
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swFdbStaticMemberPortIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.2.1.5
Specifies the port index relative to the module
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swFdbFilterTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.3
This table defines information for the device to filter packets with specific MAC address (either as the DA or as the SA). The MAC address can be a unicast address or a multicast address.This table has higher priority than both static FDB table and IGMP table. It means that if a MAC address appears on this table also appears on the static FDB table, the device will use the information provide by this table to process the packet.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwFdbFilterEntry

swFdbFilterEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.3.1
A list of information about a specific unicast/multicast MAC address for which the switch has filtering information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwFdbFilterEntry  

swFdbFilterVid 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.3.1.1
This object indicates the VLAN-ID. If the swVlanInfoStatus is port-base mode , the object ranges from 1 to 12. If VLAN is in mac-based mode or disabled, the object indicates the default VLAN-ID(0).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swFdbFilterAddress 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.3.1.2
This object indicates a unicast/multicast MAC address for which the bridge has filtering information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  MacAddress  

swFdbFilterState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.9.3.1.3
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - writing this value to the object, and then the corresponding entry will be added into the table. dst-src-addr(4) - recieved frames's destination address or source address are currently used to be filtered as it meets with the MAC address entry of the table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3), dst-src-addr(4)  

swL2PortMgmt 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4
OBJECT IDENTIFIER    

swL2PortInfoTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1
A table that contains information about every port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortInfoEntry

swL2PortInfoEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1
A list of information for each port of the device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwL2PortInfoEntry  

swL2PortInfoUnitIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1.1
Indicates ID of the unit in the device
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2PortInfoModuleIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1.2
Indicates ID of the module on the unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2PortInfoIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1.3
Indicates ID of the port on the module
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2PortInfoType 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1.4
Indicates the connector type of this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER portType-100TX(1), portType-100FXSC(2), portType-100FXMTRJ(3), portType-GIGASX(4), portType-GIGALX(5), portType-GIGATX(6), other(7)  

swL2PortInfoDescr 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1.5
Provides port type information in displayed string format
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

swL2PortInfoLinkStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1.6
Indicates port link status
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), link-pass(2), link-fail(3)  

swL2PortInfoNwayStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.1.1.7
This object indicates the port speed and duplex mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), half-10Mbps(2), full-10Mbps(3), half-100Mbps(4), full-100Mbps(5), half-1Gigabps(6), full-1Gigabps(7)  

swL2PortCtrlTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2
A table that contains control information about every port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortCtrlEntry

swL2PortCtrlEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1
A list of control information for each port of the device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwL2PortCtrlEntry  

swL2PortCtrlUnitIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.1
Indicates ID of the unit in the device
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2PortCtrlModuleIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.2
Indicates ID of the module on the unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2PortCtrlIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.3
This object indicates the device port number.(1..Max port number)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2PortCtrlAdminState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.4
This object decides the port to be enabled or disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2PortCtrlLinkStatusAlarmState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.5
Depends on this object to determine to send a trap or not when link status changes .
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2PortCtrlNwayState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.6
Chooses the port speed, duplex mode, and N-Way function mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), nway-enabled(2), nway-disabled-10Mbps-Half(3), nway-disabled-10Mbps-Full(4), nway-disabled-100Mbps-Half(5), nway-disabled-100Mbps-Full(6), nway-disabled-1Gigabps-Half(7), nway-disabled-1Gigabps-Full(8), notAvailable(10)  

swL2PortCtrlFlowCtrlState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.7
Sets IEEE 802.3x compliant flow control function as enabled or disabled. And IEEE 802.3x compliant flow control function work only when the port is in full duplex mode.The setting is effective the next time you reset or power on the hub.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlBackPressState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.8
Depends on this object to determine to enable or disable the backpressure function when the port is working in half duplex mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlLockState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.9
The state of this entry. The meanings of the values are: other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - Port lock funtion disable. enable(3) - Locking a port provides the CPU with the ability to decide which address are permitted to reside on such port, who knows about these address, and unknown packet forwarding to/from such ports. This is a way to prevent undesired traffic from being received or transmmited on the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3), notAvailable(4)  

swL2PortCtrlPriority 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.10
The priority queueing for packets received on this port, except for BPDU/IGMP packets and packets with unknown unicast destination address. IGMP and BPDU packets are always routed with high priority; packets with unknown unicast destination addresses are always routed with low priority. Other packets follow the rules below: other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. default(2) - A packet is normally classified as low priority ,unless at least one of the following is true: (a)The packet contained a TAG (per 802.1Q definition) with the priority greater or equal to 4. (b)The address-table entry for the destination address had Pd=HIGH. force-low_priority(3) - A packet is normally classified as low priority. force-high_priority(4) - A packet is normally classified as high priority.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), default(2), force-low-priority(3), force-high-priority(4), notAvailable(5)  

swL2PortCtrlStpState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.11
The state of STP(spanning tree algorithm) operation on this port. That's meaning the port whether add in the STP. The value enabled(3) indicates that STP is enabled on this port, as long as swDevCtrlStpState is also enabled for this device. When disabled(2) but swDevCtrlStpState is still enabled for the device, STP is disabled on this port : any BPDU packets received will be discarded and no BPDU packets will be propagated from the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2PortCtrlHOLState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.12
The object provides a way to prevent HOL (Head Of Line) blocking between ports. HOL protection may prevent forwarding a packet to a blocking port.The idea relies on the assumption that it is better to discard packets destined to blocking ports, then to let them consume more and more buffers in the input-port's Rx-counters because eventually these input ports may become totally blocked. The meanings of the values are: other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - HOL function disable. enabled(3) - HOL function enable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2PortCtrlBcastRisingAct 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.13
This object indicates the system action when broadcast storm rising threshold is met. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. do-nothing(2) - no action. blocking(3) - the port can discard any coming broadcast frame. blocking-trap(4) - the port can discard any coming broadcast frame. And the device can send a broadcast rising trap.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), do-nothing(2), blocking(3), blocking-trap(4), notAvailable(5)  

swL2PortCtrlBcastFallingAct 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.2.1.14
This object indicates the device action when broadcast storm falling threshold is met. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. do-nothing(2) - no action. forwarding(3) - the port has returned to normal operation mode. forwarding-trap(4) - the port has returned to normal operation mode. And the device can send a broadcast falling trap.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), do-nothing(2), forwarding(3), forwarding-trap(4), notAvailable(5)  

swL2PortStTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3
A list of port statistic Counter entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortStEntry

swL2PortStEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1
This entry include all the port statistic Counter which support by the device, like Bytes received, Bytes Sent ...
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwL2PortStEntry  

swL2PortStUnitIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.1
indicates ID of the unit in the device
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2PortStModuleIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.2
indicates ID of the module on the unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2PortStIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.3
This object indicates the device port number.(1..Max port number)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2PortStByteRx 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.4
swDevCtrlCounterMode = 2(switched-frames):This counter is incre- mented once for every data octet of good packets(unicast + multi- cast + broadcast) received. swDevCtrlCounterMode = 3(all-frames):This counter is incremented once for every data octet of good packets(unicast + multicast + broadcast packets) and for local and dropped packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStByteTx 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.5
This counter is incremented once for every data octet of a trans- mitted good packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStFrameRx 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.6
swDevCtrlCounterMode = 2(switched-frames):This counter is incre- mented once for every good packet(unicast + multicast + broadcast ) received. swDevCtrlCounterMode = 3(all-frames):This counter is incremented once for every good packet(unicast + multicast + broadcast packets) and for local and dropped packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStFrameTx 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.7
This counter is incremented once for every transmitted good packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStTotalBytesRx 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.8
This counter is incremented once for every data octet of all received packets. This include data octets of rejected and local packets which are not forwarded to the switching core for trans- mission. This counter should reflect all the data octets received on the line. Note: A nibble is not counted as a whole byte.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStTotalFramesRx 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.9
This counter is incremented once for every received packets. This include rejected and local packets which are not forwarded to the switching core for transmission. This counter should reflect all packets received on the line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStBroadcastFramesRx 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.10
swDevCtrlCounterMode = 2(switched-frames):This counter is incre- mented once for every good broadcast packet received. swDevCtrlCounterMode = 3(all-frames):This counter is incremented once for every good broadcast packet received and for local and dropped broadcast packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStMulticastFramesRx 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.11
swDevCtrlCounterMode = 2(switched-frames):This counter is incre- mented once for every good multicast packet received. swDevCtrlCounterMode = 3(all-frames):This counter is incremented once for every good multicast packet received and for local and dropped multicast packets. This counter does not include broad- cast packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStCRCError 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.12
This counter is incremented once for every received packet which meets all the following conditions: 1.Packet data length is between 64 and 1518 bytes inclusive. 2.Packet has invalid CRC. 3.Collision event , late collision event and receive error event have not been detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStOversizeFrames 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.13
The number of good frames with length more than 1518 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStFragments 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.14
This counter is incremented once for every received packet which meets all the following conditions: 1.Packet data length is less than 64 bytes or packet withourt SFD and is less than 64 bytes in length. 2.Packet has invalid CRC. 3.Collision event , late collision event and receive error event have not been detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStJabber 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.15
The number of frames with length more than 1518 bytes and with CRC error or misaligned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStCollision 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.16
The number of Collisions
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStLateCollision 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.17
The number of Late Collision(collision occurring later than 576th transmitted bit).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStFrames-64-bytes 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.18
This counter is incremented once for every received and trans- mitted packet with size of 64 bytes. This counter includes reject- ed received and transmitted packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStFrames-65-127-bytes 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.19
This counter is incremented once for every received and trans- mitted packet with size of 65 to 127 bytes. This counter includes rejected received and transmitted packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStFrames-128-255-bytes 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.20
This counter is incremented once for every received and trans- mitted packet with size of 128 to 255 bytes. This counter includes rejected received and transmitted packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStFrames-256-511-bytes 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.21
This counter is incremented once for every received and trans- mitted packet with size of 256 to 511 bytes. This counter includes rejected received and transmitted packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStFrames-512-1023-bytes 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.22
This counter is incremented once for every received and trans- mitted packet with size of 512 to 1023 bytes. This counter includ- es rejected received and transmitted packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStFrames-1024-1536-bytes 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.23
This counter is incremented once for every received and trans- mitted packet with size of 1024 to 1536 bytes. This counter includ- es rejected received and transmitted packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStFramesDroppedFrames 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.24
This counter is incremented once for every received dropped pack- et.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStMulticastFramesTx 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.25
The number of multicast frames sent. This counter does not include broadcast packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStBroadcastFramesTx 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.26
The number of broadcast frames sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swL2PortStUndersizeFrames 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.4.3.1.27
This counter is incremented once for every received packet which meets all the following conditions: 1.Packet data length is less than 64 bytes. 2.Packet has valid CRC. 3.Collision event , late collision event and receive error event have not been detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swEventPortPartition 1
The trap is sent whenever the port state enter the Partion mode when more than 61 collisions occur while trasmitting.
TRAP-TYPE    

swEventlinkChangeEvent 2
The trap is sent whenever the link state of a port changes from link up to link down or from link down to link up
TRAP-TYPE    

swEventBcastRisingStorm 3
The trap indicates that broadcast higher rising threshold . This trap including the port ID
TRAP-TYPE    

swEventBcastFallingStorm 4
The trap indicates that broadcast higher falling threshold . This trap including the port ID
TRAP-TYPE    

swIGMP 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7
OBJECT IDENTIFIER    

swIGMPCtrl 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.1
OBJECT IDENTIFIER    

swIGMPAdminState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.1.1
This object allows the user to enable/disable the IGMP snooping function. The IGMP function provided by the device includes both v1 and v2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swIGMPTimeout 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.1.2
The timeout value for sending IGMP query packet when no one was sent by the multicast router in the lan. The device will actively send the query message.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

swIGMPInfoTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.2
The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwIGMPInfoEntry

swIGMPInfoEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.2.1
Information about current IGMP query information, provided that swDevIGMPCaptureState and swIGMPCtrlState of associated VLAN entry are all enabled.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwIGMPInfoEntry  

swIGMPInfoIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.2.1.1
This object indicates the IGMP query information entry number. It could be up to 12 entries, depending on current number of VLAN entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..12  

swIGMPInfoVid 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.2.1.2
This object indicates the Vid of associated IGMP info table entry. It follows swIGMPCtrlVid in the associated entry of IGMP control table (swIGMPCtrlTable).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swIGMPInfoQueryCount 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.2.1.3
This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swIGMPInfoTxQueryCount 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.2.1.4
This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swIGMPTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.3
This table contains information regarding to the IGMP group membership report received by each port. The system will use the information recorded in this table to forward the multicast packet to those ports which have group membership. Since packets will not be forwarded to necessary ports, the network bandwith can thus be saved.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwIGMPEntry

swIGMPEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.3.1
Each entry describes the ports which are member of a specific group address. Note that when a specific multicast address existing in the table also exist in the filter table, the filter table has higher priority over this table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwIGMPEntry  

swIGMPVid 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.3.1.1
This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swIGMPGroupIpAddr 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.3.1.2
A IP multicast group address which has port membership in the underlying network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

swIGMPGroupMacAddr 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.3.1.3
The multicast MAC address corresponds to swIGMPGroupIpAddr.
Status: mandatory Access: read-only
OBJECT-TYPE    
  MacAddress  

swIGMPPortMap 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.3.1.4
Indicates the set of ports which are members of this multicast group. These ports are represented by a octet string.The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortList  

swIGMPIpGroupReportCount 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.3.1.5
Indicates the number of group membership report packets received by the device corresponding to this multicast group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swIGMPCtrlTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.4
The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swVlanInfoStatus). If VLAN is disabled or in Mac-Base mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with index range from 1 to 12.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwIGMPCtrlEntry

swIGMPCtrlEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.4.1
The entry in IGMP control table (swIGMPCtrlTable). The entry is effective only when IGMP capture switch is enabled.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwIGMPCtrlEntry  

swIGMPCtrlIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.4.1.1
This object indicates the IGMP control entry number.Its scale depends on current VLAN state (es400VlanInfoStatus). If VLAN is disabled or in Mac-Base mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries is 12, with index range from 1 to 12.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..12  

swIGMPCtrlVid 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.4.1.2
This object indicates the IGMP control entry's VLAN id. If VLAN is disabled or in Mac-Base mode, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12 , fixed form. If VLAN is in 802.1q mode, the Vid setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

swIGMPCtrlTimer 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.4.1.3
The timer value for sending IGMP query packet when none was sent by the multicast router in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997. And it recommends a default of 125 seconds. The timeout value must be at least 30 seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 30..9999  

swIGMPCtrlState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.7.4.1.4
This object indicates the status of this entry. other(1) - This entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP funtion is disabled for this entry. enable(3) - IGMP funtion is enabled for this entry. deleted(4) - IGMP entry is deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), deleted(4)  

swL2DevMgmt 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1
OBJECT IDENTIFIER    

swL2DevCtrl 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1
OBJECT IDENTIFIER    

swL2DevCtrlStpState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.1
This object can be enabled or disabled spanning tree algorithm during runtime of the system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevCtrlPartitionModeState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.2
This object used to enable or disable port auto partition. When the object apply for all ports of the device
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevCtrlTableLockState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.3
This object indicates whether the address table is locked. In other words, the address table doesn't learn any more new address. The aging timer is suspended when the address table is locked. As long as the table is locked, all of the frames are dropped if the destination can not be found in the address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevCtrlHOLState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.4
The object provides a way to prevent HOL (Head Of Line) blocking between ports. HOL protection may prevent forwarding a packet to a blocking port.The idea relies on the assumption that it is better to discard packets destined to blocking ports, then to let them consume more and more buffers in the input-port's Rx-counters because eventually these input ports may become totally blocked. The meanings of the values are: other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - HOL function disable for device. enabled(3) - HOL function enable for device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevCtrlAddrLookupModesAndHitRate 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.5
According to the differnet address looke mode setting, to enlarge the address table size is possible in device. But there is side effect as the higher level you have, the lower thorughput device has. That means Level 0 get the smallest table size, but get better performace. We recommand the user use the Level 1 as defualt setting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER level0(1), level1(2), level2(3), level3(4), level4(5), level5(6), level6(7), level7(8)  

swL2DevCtrlUploadImageFileName 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.6
The name of the image file to be uploaded from the device to TFTP server when enabling image upload function (by writing swDevCtrlUploadImage).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

swL2DevCtrlUploadImage 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.7
Image file upload control. Writing it by any value will immediately invoke image upload function.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

swL2DevCtrlClearAddressTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.1.8
This object indicates the agent clear address table. Setting this object to clear(2) will clear address table. The agent alwats return other(1) when this object is read.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), clear(2)  

swL2DevAlarm 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.2
OBJECT IDENTIFIER    

swL2DevAlarmPartition 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.2.1
Depending on this object, the device send a trap or not when any one of the device's ports was partitioned.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevAlarmNewRoot 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.2.2
When the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevAlarmTopChange 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.2.3
This object determines to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port tranition, the device doesn't send the trap if this object value is disabled or other.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevAlarmLinkChange 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.1.2.4
This object determines to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device doesn't send the trap if this object value is disabled or other.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swVlan 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8
OBJECT IDENTIFIER    

pBridgeMIBObjects 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4
OBJECT IDENTIFIER    

dot1dExtBase 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.1
OBJECT IDENTIFIER    

dot1dPriority 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.2
OBJECT IDENTIFIER    

dot1dGarp 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.3
OBJECT IDENTIFIER    

dot1dGmrp 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.4
OBJECT IDENTIFIER    

dot1dDeviceCapabilities 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.1.1
Indicates the optional parts of IEEE 802.1D and 802.1Q that are implemented by this device and are managable through this MIB. Capabilities that are allowed on a per-port basis are indicated in dot1dPortCapabilities.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dot1dTrafficClassesEnabled 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.1.2
The value true(1) indicates that Traffic Classes are enabled on this bridge. When false(2), the bridge operates with a single priority level for all traffic.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TruthValue  

dot1dGmrpStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.1.3
The administrative status requested by management for GMRP. The value enabled(1) indicates that GMRP should be enabled on this device, in all VLANs, on all ports for which it has not been specifically disabled. When disabled(2), GMRP is disabled, in all VLANs, on all ports and all GMRP packets will be forwarded transparently. This object affects both Applicant and Registrar state machines. A transition from disabled(2) to enabled(1) will cause a reset of all GMRP state machines on all ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnabledStatus  

dot1dPortCapabilitiesTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.1.4
A table that contains capabilities information about every port that is associated with this bridge.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1dPortCapabilitiesEntry

dot1dPortCapabilitiesEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.1.4.1
A set of capabilities information about this port indexed by dot1dBasePort.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Dot1dPortCapabilitiesEntry  

dot1dPortCapabilities 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.1.4.1.1
Indicates the parts of IEEE 802.1D and 802.1Q that are optional on a per-port basis that are implemented by this device and are managable through this MIB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dot1dPortPriorityTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.2.1
A table that contains information about every port that is associated with this transparent bridge.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1dPortPriorityEntry

dot1dPortPriorityEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.2.1.1
A list of the number of egress traffic classes supported for each port in a transparent bridge. This is indexed by dot1dBasePort.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Dot1dPortPriorityEntry  

dot1dPortNumTrafficClasses 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.2.1.1.1
The number of egress traffic classes supported on this port. This object may optionally be read-only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

dot1dPortGarpTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.3.1
A table of GARP control information about every bridge port. This is indexed by dot1dBasePort.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1dPortGarpEntry

dot1dPortGarpEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.3.1.1
GARP control information for a bridge port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Dot1dPortGarpEntry  

dot1dPortGarpJoinTime 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.3.1.1.1
The GARP Join time, in centiseconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  TimeInterval 20..65535  

dot1dPortGarpLeaveTime 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.3.1.1.2
The GARP Leave time, in centiseconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  TimeInterval 20..65535  

dot1dPortGarpLeaveAllTime 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.3.1.1.3
The GARP LeaveAll time, in centiseconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  TimeInterval 20..65535  

dot1dPortGmrpTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.4.1
A table of GMRP control and status information about every bridge port. Augments the dot1dBasePortTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1dPortGmrpEntry

dot1dPortGmrpEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.4.1.1
GMRP control and status information for a bridge port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Dot1dPortGmrpEntry  

dot1dPortGmrpStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.4.1.1.1
The state of GMRP operation on this port. The value enabled(1) indicates that GMRP is enabled on this port, in all VLANs, as long as dot1dGmrpStatus is also enabled for this device. When disabled(2) but dot1dGmrpStatus is still enabled for the device, GMRP is disabled on this port in all VLANs: any GMRP packets received will be silently discarded and no GMRP registrations will be propagated from other ports. This object affects all GMRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GMRP state machines on this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnabledStatus  

dot1dPortGmrpFailedRegistrations 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.4.1.1.2
The total number of failed GMRP registrations, for any reason, in all VLANs, on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

dot1dPortGmrpLastPduOrigin 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.4.4.1.1.3
The Source MAC Address of the last GMRP message received on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  MacAddress  

qBridgeMIBObjects 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5
OBJECT IDENTIFIER    

dot1qBase 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.1
OBJECT IDENTIFIER    

dot1qTp 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2
OBJECT IDENTIFIER    

dot1qStatic 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3
OBJECT IDENTIFIER    

dot1qVlan 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4
OBJECT IDENTIFIER    

dot1qVlanVersionNumber 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.1.1
The version number of IEEE 802.1Q that this device supports.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER version1(1)  

dot1qMaxVlanId 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.1.2
The maximum IEEE 802.1Q VLAN ID that this device supports.
Status: mandatory Access: read-only
OBJECT-TYPE    
  VlanId  

dot1qMaxSupportedVlans 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.1.3
The maximum number of IEEE 802.1Q VLANs that this device supports.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

dot1qNumVlans 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.1.4
The current number of IEEE 802.1Q VLANs that are configured in this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

dot1qGvrpStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.1.5
The administrative status requested by management for GVRP. The value enabled(1) indicates that GVRP should be enabled on this device, on all ports for which it has not been specifically disabled. When disabled(2), GVRP is disabled on all ports and all GVRP packets will be forwarded transparently. This object affects all GVRP Applicant and Registrar state machines. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on all ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnabledStatus  

dot1qFdbTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.1
A table that contains configuration and control information for each Filtering Database currently operating on this device. Entries in this table appear automatically when VLANs are assigned FDB IDs in the dot1qVlanCurrentTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1qFdbEntry

dot1qFdbEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.1.1
Information about a specific Filtering Database.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Dot1qFdbEntry  

dot1qFdbId 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.1.1.1
The identity of this Filtering Database.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

dot1qFdbDynamicCount 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.1.1.2
The current number of dynamic entries in this Filtering Database.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

dot1qTpFdbTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.2
A table that contains information about unicast entries for which the device has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1qTpFdbEntry

dot1qTpFdbEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.2.1
Information about a specific unicast MAC address for which the device has some forwarding and/or filtering information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Dot1qTpFdbEntry  

dot1qTpFdbAddress 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.2.1.1
A unicast MAC address for which the device has forwarding and/or filtering information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MacAddress  

dot1qTpFdbPort 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.2.1.2
Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of dot1qTpFdbAddress has been seen. A value of '0' indicates that the port number has not been learned but that the device does have some forwarding/filtering information about this address (e.g. in the dot1qStaticUnicastTable). Implementers are encouraged to assign the port value to this object whenever it is learned even for addresses for which the corresponding value of dot1qTpFdbStatus is not learned(3).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

dot1qTpFdbStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.2.1.3
The status of this entry. The meanings of the values are: other(1) - none of the following. This may include the case where some other MIB object (not the corresponding instance of dot1qTpFdbPort, nor an entry in the dot1qStaticUnicastTable) is being used to determine if and how frames addressed to the value of the corresponding instance of dot1qTpFdbAddress are being forwarded. invalid(2) - this entry is no longer valid (e.g., it was learned but has since aged out), but has not yet been flushed from the table. learned(3) - the value of the corresponding instance of dot1qTpFdbPort was learned and is being used. self(4) - the value of the corresponding instance of dot1qTpFdbAddress represents one of the device's addresses. The corresponding instance of dot1qTpFdbPort indicates which of the device's ports has this address. mgmt(5) - the value of the corresponding instance of dot1qTpFdbAddress is also the value of an existing instance of dot1qStaticAddress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), invalid(2), learned(3), self(4), mgmt(5)  

dot1qTpGroupTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.3
A table containing filtering information for VLANs configured into the bridge by (local or network) management, or learnt dynamically, specifying the set of ports to which frames received on a VLAN for this FDB and containing a specific Group destination address are allowed to be forwarded.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1qTpGroupEntry

dot1qTpGroupEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.3.1
Filtering information configured into the bridge by management, or learnt dynamically, specifying the set of ports to which frames received on a VLAN and containing a specific Group destination address, are allowed to be forwarded. The subset of these ports learnt dynamically is also provided.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Dot1qTpGroupEntry  

dot1qTpGroupAddress 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.3.1.1
The destination Group MAC address in a frame to which this entry's filtering information applies.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MacAddress  

dot1qTpGroupEgressPorts 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.3.1.2
The complete set of ports, in this Filtering Database, to which frames destined for this Group MAC address are currently being explicitly forwarded. This does not include ports for which this address is only implicitly forwarded, in the dot1qForwardAllPorts list.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortList  

dot1qTpGroupLearnt 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.2.3.1.3
The subset of ports in dot1qTpGroupEgressPorts which were learnt by GMRP or some other dynamic mechanism, in this Filtering database.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortList  

dot1qStaticMulticastTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3.2
A table containing filtering information for Multicast and Broadcast MAC addresses for each VLAN, configured into the device by (local or network) management specifying the set of ports to which frames received from specific ports and containing specific Multicast and Broadcast destination addresses are allowed to be forwarded. A value of zero in this table as the port number from which frames with a specific destination address are received, is used to specify all ports for which there is no specific entry in this table for that particular destination address. Entries are valid for Multicast and Broadcast addresses only.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1qStaticMulticastEntry

dot1qStaticMulticastEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3.2.1
Filtering information configured into the device by (local or network) management specifying the set of ports to which frames received from this specific port for this VLAN and containing this Multicast or Broadcast destination address are allowed to be forwarded.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Dot1qStaticMulticastEntry  

dot1qStaticMulticastAddress 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3.2.1.1
The destination MAC address in a frame to which this entry's filtering information applies. This object must take the value of a Multicast or Broadcast address.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MacAddress  

dot1qStaticMulticastReceivePort 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3.2.1.2
Either the value '0', or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of zero indicates that this entry applies on all ports of the device for which there is no other applicable entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..65535  

dot1qStaticMulticastStaticEgressPorts 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3.2.1.3
The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of any dynamic information e.g. from GMRP. A port may not be added in this set if it is already a member of the set of ports in dot1qStaticMulticastForbiddenEgressPorts. The default value of this object is a string of ones of appropriate length.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PortList  

dot1qStaticMulticastForbiddenEgressPorts 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3.2.1.4
The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must not be forwarded, regardless of any dynamic information e.g. from GMRP. A port may not be added in this set if it is already a member of the set of ports in dot1qStaticMulticastStaticEgressPorts. The default value of this object is a string of zeros of appropriate length.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PortList  

dot1qStaticMulticastStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.3.2.1.5
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the following values. invalid(2) - writing this value to the object removes the corresponding entry. permanent(3) - this entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - this entry is currently in use and will remain so until the next reset of the bridge. deleteOnTimeout(5) - this entry is currently in use and will remain so until it is aged out.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), permanent(3), deleteOnReset(4), deleteOnTimeout(5)  

dot1qVlanNumDeletes 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.1
The number of times a VLAN entry has been deleted from the dot1qVlanCurrentTable (for any reason). If an entry is deleted, then inserted, and then deleted, this counter will be incremented by 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

dot1qVlanCurrentTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2
A table containing current configuration information for each VLAN currently configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1qVlanCurrentEntry

dot1qVlanCurrentEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1
Information for a VLAN configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Dot1qVlanCurrentEntry  

dot1qVlanTimeMark 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1.1
A TimeFilter for this entry. See the TimeFilter textual convention to see how this works.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TimeFilter  

dot1qVlanIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1.2
The VLAN-ID or other identifier refering to this VLAN.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  VlanIndex  

dot1qVlanFdbId 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1.3
The Filtering Database used by this VLAN. This is one of the dot1qFdbId values in the dot1qFdbTable. This value is allocated automatically by the device whenever the VLAN is created: either dynamically by GVRP, or by management, in dot1qVlanStaticTable. Allocation of this value follows the learning constraints defined for this VLAN in dot1qLearningConstraintsTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

dot1qVlanCurrentEgressPorts 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1.4
The set of ports which are transmitting traffic for this VLAN as either tagged or untagged frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortList  

dot1qVlanCurrentUntaggedPorts 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1.5
The set of ports which are transmitting traffic for this VLAN as untagged frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortList  

dot1qVlanStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1.6
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the following values. permanent(2) - this entry, corresponding to an entry in dot1qVlanStaticTable, is currently in use and will remain so after the next reset of the device. The port lists for this entry include ports from the equivalent dot1qVlanStaticTable entry and ports learnt dynamically. dynamicGvrp(3) - this entry is currently in use and will remain so until removed by GVRP. There is no static entry for this VLAN and it will be removed when the last port leaves the VLAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), permanent(2), dynamicGvrp(3)  

dot1qVlanCreationTime 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.2.1.7
The value of sysUpTime when this VLAN was created.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

dot1qVlanStaticTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.3
A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1qVlanStaticEntry

dot1qVlanStaticEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.3.1
Static information for a VLAN configured into the device by (local or network) management.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Dot1qVlanStaticEntry  

dot1qVlanStaticName 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.3.1.1
An administratively assigned string, which may be used to identify the VLAN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

dot1qVlanStaticEgressPorts 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.3.1.2
The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros of appropriate length, indicating not fixed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PortList  

dot1qVlanForbiddenEgressPorts 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.3.1.3
The set of ports which are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be included or excluded affect the per-port per-VLAN Registrar control for Registration Forbidden for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanStaticEgressPorts. The default value of this object is a string of zeros of appropriate length, excluding all ports from the forbidden set.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PortList  

dot1qVlanStaticUntaggedPorts 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.3.1.4
The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (VlanId 001) is a string of appropriate length including all ports. There is no specified default for other VLANs. If a device cannot support a value being set then its agent will reject the set operation. Attempts to set more than one VLAN to be untagged on egress may be rejected by devices which do not support this option.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PortList  

dot1qVlanStaticRowState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.3.1.5
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

dot1qPortVlanTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.4
A table containing per port control and status information for VLAN configuration in the device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1qPortVlanEntry

dot1qPortVlanEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.4.1
Information controlling VLAN configuration for a port on the device. This is indexed by dot1dBasePort.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Dot1qPortVlanEntry  

dot1qPvid 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.4.1.1
The PVID, the VLAN ID assigned to untagged frames or Prority-Tagged frames received on this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  VlanIndex  

dot1qPortIngressFiltering 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.4.1.2
When this is true(1) the device will discard incoming frames for VLANs which do not include this Port in its Member set. When false(2), the port will accept all incoming frames. This control does not affect VLAN independent BPDU frames, such as GVRP and STP. It does affect VLAN dependent BPDU frames, such as GMRP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1qPortGvrpStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.4.1.3
The state of GVRP operation on this port. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disabled on this port: any GVRP packets received will be silently discarded and no GVRP registrations will be propagated from other ports. This object affects all GVRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnabledStatus  

dot1qPortGvrpFailedRegistrations 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.4.1.4
The total number of failed GVRP registrations, for any reason, on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

dot1qPortGvrpLastPduOrigin 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.5.4.4.1.5
The Source MAC Address of the last GVRP message received on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  MacAddress  

swPortSniff 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.5
OBJECT IDENTIFIER    

swSniffCtrlTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.5.1
A list of port sniffing entries.Port Sniffing function provides an easy way to monitor traffic on any port. In this way any good packets appears on the source mirror port also shows up on the target mirror port without need to reconstruct the LAN.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwSniffCtrlEntry

swSniffCtrlEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.5.1.1
Each entry contains a pair of sniff source port and target port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwSniffCtrlEntry  

swSniffIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.5.1.1.1
A unique number to identify the sniff entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swSniffSourcePort 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.5.1.1.2
Indicates the source port whose traffic will be sniffed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..96  

swSniffTargetPort 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.5.1.1.3
Indicates the target port which the traffic appears on the source sniffed port will be copied to. A trunk port member cannot be configured as a target Sniffing port
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..96  

swSniffState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.5.1.1.4
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - Sniff funtion disable. enable(3) - Sniff funtion enable and Sniff received or transmit packet by Sniff source port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

swPortTrunk 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6
OBJECT IDENTIFIER    

swPortTrunkCtrlTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1
This table specifies which port trunking configuration. Trunking ID is as following : trunk 1 - unit1, base, port5~12; trunk 2 - unit1, base, port13~20; trunk 3 - unit1, slot1, port21,22; trunk 4 - reserved; trunk 5, 9, 13 - unit2(3, 4), base, port7~14; trunk 6, 10, 14 - unit2(3, 4), base, port15~22; trunk 7, 11, 15 - unit2(3, 4), slot1, port23,24; trunk 8, 12, 16 - reserved
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwPortTrunkCtrlEntry

swPortTrunkCtrlEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1.1
Each entry specifies which ports are grouped as a single logical link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwPortTrunkCtrlEntry  

swPortTrunkCtrlIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1.1.1
The index of logical trunk of ports.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swPortTrunkCtrlAnchorPort 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1.1.2
get anchor port number between trunk ports
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

swPortTrunkCtrlMasterPort 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1.1.3
get master port number between trunk ports
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swPortTrunkCtrlName 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1.1.4
The name of logical trunk of ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

swPortTrunkCtrlMember 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1.1.5
specifies the member ports which are grouped as a trunk.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PortList  

swPortTrunkCtrlState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.1.1.6
This object determines whether the trunk setting is in enable/disable state.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swPortTrunkMemberTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.2
A list of information provide a different view for member ports grouped as a trunk
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwPortTrunkMemberEntry

swPortTrunkMemberEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.2.1
Each entry corresponds to a member port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwPortTrunkMemberEntry  

swPortTrunkMemberIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.2.1.1
Indicates the trunk ID where the port is located.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swPortTrunkMemberUnitIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.2.1.2
Indicates the unit ID where the port is located.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swPortTrunkMemberModuleIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.2.1.3
Indicates the module ID where the port is located.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swPortTrunkMemberPortIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.6.2.1.4
Indicates the port index relative to the module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swVlanCtrl 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.1
OBJECT IDENTIFIER    

swMacBaseVlan 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2
OBJECT IDENTIFIER    

swPortBaseVlan 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3
OBJECT IDENTIFIER    

swVlanCtrlMode 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.1.1
This object controls which Vlan function will be enable (or disable) when the switch hub restart at the startup (power on) or warm start.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), mac-base(3), ieee8021q(4), port-base(5)  

swVlanInfoStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.1.2
This object indicates which Vlan function be enable (or disable) in mandatoryly stage. There are no effect when change swVlanCtrlMode vlaue in the system running.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), disabled(2), mac-base(3), ieee8021q(4)  

swVlanSnmpPortVlan 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.1.3
Indicates the Vlan which the SNMP port belongs to. The value range is 1 to 4094.
Status: mandatory Access: read-write
OBJECT-TYPE    
  VlanIndex  

swMacBaseVlanInfo 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.1
OBJECT IDENTIFIER    

swMacBaseVlanMaxNum 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.1.1
The maximum number of Mac base Vlan allowed by the system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swMacBaseVlanAddrMaxNum 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.1.2
The maximum number of entries in Mac-based Vlan address table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swMacBaseVlanCtrlTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.2
A table that contains information about MAC base Vlan entries for which the switch has forwarding and/or filtering information. This information is used by the transparent switching function in determining how to propagate a received frame.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMacBaseVlanCtrlEntry

swMacBaseVlanCtrlEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.2.1
A list of information about a specific MAC base Vlan configuration portlist for which the switch has some forwarding and/or filtering information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwMacBaseVlanCtrlEntry  

swMacBaseVlanDesc 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.2.1.1
A textual description of the Mac Base Vlan for memorization. The string cannot set to empty string. There is a default value for this string
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..12)  

swMacBaseVlanMacMember 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.2.1.2
This object indicates the total number of MAC addresses contained in the VLAN entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swMacBaseVlanCtrlState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.2.1.3
This object indicates the MacBase Vlan state.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swMacBaseVlanAddrTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.3
A table that contains information about unicast or multicast entries for which the switch has forwarding and/or filtering information. This information is used by the transparent switching function in determining how to propagate a received frame. Note that the priority of MacBaseVlanAddr table entries is lowest than Filtering Table and FDB Table, i.e. if there is a table hash collision between the entries of MacBaseVlanAddr Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of MacBaseVlanAddr Table. This state is same of FDB table. See swFdbFilterTable and swFdbStaticTable description also.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMacBaseVlanAddrEntry

swMacBaseVlanAddrEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.3.1
A list of information about a specific unicast or multicast MAC address for which the switch has some forwarding and/or filtering information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwMacBaseVlanAddrEntry  

swMacBaseVlanAddr 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.3.1.1
This object indictaes a unicast or multicast MAC address for which the bridge has forwarding and/or filtering information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  MacAddress  

swMacBaseVlanAddrVlanDesc 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.3.1.2
A textual description of the Mac Base Vlan for memorization .
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..64)  

swMacBaseVlanAddrState 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.3.1.3
This object indicates the MacBase Vlan Address entry state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

swMacBaseVlanAddrStatus 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.2.3.1.4
This object indicates the MacBase Vlan Address entry state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. apply(2) - this entry is currently in use and reside in the table. not-apply(3) - this entry is reside in the table but currently not in use due to conflict with filter table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), apply(2), not-apply(3)  

swPortBaseVlanTotalNum 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.1
The total number of Port-Base Vlan which is in enabled state within this switch hub.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swPortBaseVlanDefaultVlanTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.2
A table that contains default Port-Based VLAN list entries for the switch. The entry (Vid = 1,i.e. swPortBaseVlanDefaultPvid = 1) is defalut Port-Based VLAN , maintained by system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwPortBaseVlanDefaultVlanEntry

swPortBaseVlanDefaultVlanEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.2.1
A list of default Port-Based VLAN information in swPortBaseVlanDefaultVlanTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwPortBaseVlanDefaultVlanEntry  

swPortBaseVlanDefaultPvid 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.2.1.1
This object indicates the default Port-Base Vlan ID. It occupies only 1 entry in VLAN table, with VID=1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swPortBaseVlanDefaultDesc 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.2.1.2
A textual description of the Port-Base Vlan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..12)  

swPortBaseVlanDefaultPortList 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.2.1.3
This object indicates the port member set of the specified Vlan. Each Vlan has a octect string to indicate the port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PortList  

swPortBaseVlanDefaultPortNumber 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.2.1.4
This object indicates the number of ports of the entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swPortBaseVlanConfigTable 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.3
A table that contains Port-Based VLAN list entries for the switch. The device can't support port overlapping in Port-Based VLAN.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwPortBaseVlanConfigEntry

swPortBaseVlanConfigEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.3.1
A list of information about a specific Port-Based VLAN configuration in swPortBaseVlanConfigTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwPortBaseVlanConfigEntry  

swPortBaseVlanConfigPvid 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.3.1.1
This object indicates the Port-Base Vlan ID. There are up to 11 entries for current product now. The object range varies from 2 to 12.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 2..12  

swPortBaseVlanConfigDesc 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.3.1.2
A textual description of the Port-Base Vlan. It cannot be a null string. And each description must be unique in the table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..12)  

swPortBaseVlanConfigPortList 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.3.1.3
This object indicates which ports are belong to the Vlan. Each Vlan has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PortList  

swPortBaseVlanConfigPortNumber 1.3.6.1.4.1.326.2.20.1.2.2.2.25.2.8.3.3.1.4
This object indicates the number of ports of the entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER