ExaltComProducts

File: ExaltComProducts.mib (76305 bytes)

Imported modules

SNMPv2-SMI ExaltComm SNMPv2-CONF
SNMPv2-TC

Imported symbols

MODULE-IDENTITY OBJECT-IDENTITY OBJECT-TYPE
IpAddress Integer32 Gauge32
exaltcommunications EthMainStatusT EthAuxStatusT
AuxNmsMode EthPortMode Te1StatusT
Te1LboT EnableStatusT Te1LineCodeT
Te1LoopBackModeT AlarmLevelT Led4ColorT
VlanStatusT VlanGroupT ExaltEnableT
AcmModulationT FileTransferTypeT FileTransferStartT
NtpClientEnableT TimeZoneT OBJECT-GROUP
DisplayString TEXTUAL-CONVENTION

Defined Types

PwType  
This is a PW field.
TEXTUAL-CONVENTION    
  OCTET STRING Size(8..16)  

Te1InterfacesEntry  
SEQUENCE    
  te1Status Te1StatusT
  t1LBO Te1LboT
  te1AIS Te1StatusT
  t1LineCode Te1LineCodeT
  te1LoopBackMode Te1LoopBackModeT

Te1Alarms1Entry  
SEQUENCE    
  locTe1Alarm AlarmLevelT

Te1AlarmsEntry  
SEQUENCE    
  remTe1Alarm AlarmLevelT

LocEthPerfInterfacesEntry  
SEQUENCE    
  locEthUtilizationIn Integer32
  locEthUtilizationOut Integer32
  locEthSpeed DisplayString

Defined Values

productsMIB 1.3.6.1.4.1.25651.1
Exalt devices
MODULE-IDENTITY    

productsMIBNotifications 1.3.6.1.4.1.25651.1.1
OBJECT IDENTIFIER    

productsMIBObjects 1.3.6.1.4.1.25651.1.2
OBJECT IDENTIFIER    

radioInfo 1.3.6.1.4.1.25651.1.2.1
Common Radio Information to all Exalt devices.
Status: current Access: read-write
OBJECT-IDENTITY    

modelName 1.3.6.1.4.1.25651.1.2.1.1
A descriptive name for the Radio. See Web, Radio Information, Model Name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

partNumber 1.3.6.1.4.1.25651.1.2.1.2
The Part Number of the Radio. See Web, Radio Information, Part Number.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

serialNumber 1.3.6.1.4.1.25651.1.2.1.3
The Radio Serial Number. See Web, Radio Inforamtion, Serial Number.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

interfaceType 1.3.6.1.4.1.25651.1.2.1.4
The Interfaces available on this radio. Ethernet, T1/E1, etc. See Web, Radio Information, Interface Type.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..30)  

firmwareVersion 1.3.6.1.4.1.25651.1.2.1.5
The Radio Firmware Version. See Web, Radio Information, Firmware Version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

bootVersion 1.3.6.1.4.1.25651.1.2.1.6
The Radio Boot Code Version. See Web, Radio Information, Boot Version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

rdkDbVer 1.3.6.1.4.1.25651.1.2.1.11
The Device RDK Database Version. See Web, Radio Information, RDK Database Version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

txFreqRange 1.3.6.1.4.1.25651.1.2.1.12
The Radio Tx Frequency Range. FDD radios have a Tx and Rx frequency range. See Web, Radio Information, RF Transmit range. TDD radios have one frequency range. See Web, Radio Information, RF Frequency Band.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

rxFreqRange 1.3.6.1.4.1.25651.1.2.1.13
The Radio Rx Frequency Range. FDD radios have a Tx and Rx frequency range. See Web, Radio Information, RF Receive range. TDD radios have one frequency range. See Web, Radio Information, RF Frequency Band.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

rfFreqBand 1.3.6.1.4.1.25651.1.2.1.14
The Device Frequency Band (Range). TDD radios have N/A value in this field. FDD radios have TX High or TX Low depending on used diplexer and Transmit frequency. See Web, Radio Information, Tx Band.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

hwId 1.3.6.1.4.1.25651.1.2.1.15
The Device Hardware ID number. See Web, Radio Information, Hardware ID number
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

modelNumber 1.3.6.1.4.1.25651.1.2.1.16
The Model Number of the Radio. See Web, Radio Information, Model Number
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

licenseFeatures 1.3.6.1.4.1.25651.1.2.1.17
The list of the features enabled by License Key
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

radioAdmin 1.3.6.1.4.1.25651.1.2.2
Radio Administration parameters.
Status: current Access: read-only
OBJECT-IDENTITY    

sysDate 1.3.6.1.4.1.25651.1.2.2.1
The Radio System Date, MM/DD/YYYY. See Web, Administration, Settings, Date. To make permanent, write save to commitAdminSettings after change. After commit, SNMP restarts and will be down for 30 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(10)  

sysTime 1.3.6.1.4.1.25651.1.2.2.2
The Radio System Time, HH:MM:SS, as 24 hours. See Web, Administration, Settings, Time. To make permanent, write save to commitAdminSettings after change. After commit, SNMP restarts and will be down for 30 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(8)  

radioName 1.3.6.1.4.1.25651.1.2.2.3
OBJECT IDENTIFIER    

rnLocal 1.3.6.1.4.1.25651.1.2.2.3.1
The user specifiable Radio Name for this radio. See Web, Administration, Settings, Radio Name. To make permanent, write save to commitAdminSettings after change.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..32)  

rnRemote 1.3.6.1.4.1.25651.1.2.2.3.2
The Radio Name of the Radio at the far end of this RF Link. Can only be set at that radio. See Web, Administration, Settings, Radio Name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

linkName 1.3.6.1.4.1.25651.1.2.2.4
The user specifiable Link Name for this radio. See Web, Administration, Settings, Link Name. To make permanent, write save to commitAdminSettings after change.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

linkSecKey 1.3.6.1.4.1.25651.1.2.2.5
The Link Security Key must match on both ends of an RF Link for traffic to pass. See Web, Administration, Settings, Link Security Key. To make permanent, write save to commitAdminSettings after change.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(12)  

adminPassword 1.3.6.1.4.1.25651.1.2.2.6
The password for admin login to Web/CLI. See Web, Administration, Settings, Admin Password. To make permanent, write save to commitAdminSettings after change.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

userPassword 1.3.6.1.4.1.25651.1.2.2.7
The password for user login to Web/CLI. See Web, Administration, Settings, User Password. To make permanent, write save to commitAdminSettings after change.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

ipAddress 1.3.6.1.4.1.25651.1.2.2.8
OBJECT IDENTIFIER    

ipLocal 1.3.6.1.4.1.25651.1.2.2.8.1
The IP address of local radio. This IP address is used to manage radio. See Web, Administration, Settings, IP Address. To make permanent, write save to commitAdminSettings after change.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

ipRemote 1.3.6.1.4.1.25651.1.2.2.8.2
The IP address of the remote Radio. This IP address is used to manage Remote radio. Can only be set at that radio. See Web, Administration, Settings, IP Address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

subnetMask 1.3.6.1.4.1.25651.1.2.2.9
The Subnet Mask for IP address of local radio. See Web, Administration, Settings, IP Mask. To make permanent, write save to commitAdminSettings after change.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

ipAddressNetmask 1.3.6.1.4.1.25651.1.2.2.10
The IP address and Subnet Mask of local radio. ie 10.0.0.1/24. To make permanent, write save to commitAdminSettings after change.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(9..18)  

defaultGateway 1.3.6.1.4.1.25651.1.2.2.11
The Default Gateway for local radio port. See Web, Administration, Settings, Default Gateway. To make permanent, write save to commitAdminSettings after change.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

aesEnable 1.3.6.1.4.1.25651.1.2.2.12
The AES enable(0)/disable(1). AES (Advance Encryption Standard) can be implemented to provide additional data security for the wireless link. This function requires an upgrade license key (purchased separately). See Web, Administration, Settings, AES Settings, Enable AES. To make permanent, write save to commitAdminSettings after change.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER aesDisable(0), aesEnable(1)  

aesKey 1.3.6.1.4.1.25651.1.2.2.13
The symmetric AES key for encrypt/decrypt payload data. Different bitlength encryption license keys (for example, 128-bit and 256-bit) are available, depending on model type and license type. AES Key should match both on local radio and far end radio. See Web, Administration, Settings, AES Settings, AES Key. To make permanent, write save to commitAdminSettings after change.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..64)  

licKey 1.3.6.1.4.1.25651.1.2.2.14
The license key which defines radio features and capabilities. See Web, Administration, Settings, License Key. To make permanent, write save to commitAdminSettings after change.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..32)  

snmpConfig 1.3.6.1.4.1.25651.1.2.2.17
OBJECT IDENTIFIER    

trapIpaddr1 1.3.6.1.4.1.25651.1.2.2.17.1
The IP address to which the SNMP traps are directed. See Web, Administration, SNMP, Traps, Trap Destination IP Address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

trapIpaddrEnable1 1.3.6.1.4.1.25651.1.2.2.17.2
Enable/Disable trap ip address.
Status: current Access: read-only
OBJECT-TYPE    
  EnableStatusT  

trapIpaddr2 1.3.6.1.4.1.25651.1.2.2.17.3
The IP address to which the SNMP traps are directed. See Web, Administration, SNMP, Traps, Trap Destination IP Address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

trapIpaddrEnable2 1.3.6.1.4.1.25651.1.2.2.17.4
Enable/Disable trap ip address.
Status: current Access: read-write
OBJECT-TYPE    
  EnableStatusT  

trapIpaddr3 1.3.6.1.4.1.25651.1.2.2.17.5
The IP address to which the SNMP traps are directed. See Web, Administration, SNMP, Traps, Trap Destination IP Address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

trapIpaddrEnable3 1.3.6.1.4.1.25651.1.2.2.17.6
Enable/Disable trap ip address.
Status: current Access: read-write
OBJECT-TYPE    
  EnableStatusT  

trapIpaddr4 1.3.6.1.4.1.25651.1.2.2.17.7
The IP address to which the SNMP traps are directed. See Web, Administration, SNMP, Traps, Trap Destination IP Address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

trapIpaddrEnable4 1.3.6.1.4.1.25651.1.2.2.17.8
Enable/Disable trap ip address.
Status: current Access: read-write
OBJECT-TYPE    
  EnableStatusT  

trapAuth 1.3.6.1.4.1.25651.1.2.2.17.9
Authentication trap enable(1)/disable(0). This is an SNMP standard trap when password information for SNMP is incorrect. See Web, Administration, SNMP, Traps, Authentication Trap.
Status: current Access: read-write
OBJECT-TYPE    
  EnableStatusT  

trapReboot 1.3.6.1.4.1.25651.1.2.2.17.10
Reboot trap enable(0)/disable(1). This trap is sent after any radio reboot to inform the manager of the reboot status. See Web, Administration, SNMP, Traps, Radio Reboot Trap.
Status: current Access: read-write
OBJECT-TYPE    
  EnableStatusT  

trapLocLinkStat 1.3.6.1.4.1.25651.1.2.2.17.11
Local Link Status trap enable(0)/disable(1). This trap is sent when Link is in errored state (equivalent to the Link LED). See Web, Administration, SNMP, Traps, Local Link Status Trap.
Status: current Access: read-write
OBJECT-TYPE    
  EnableStatusT  

trapLocAlarmStat 1.3.6.1.4.1.25651.1.2.2.17.12
Local Alarm Status trap enable(0)/disable(1). This trap is sent when local radio Status is in errored state (equivalent to the Status LED). See Web, Administration, SNMP, Traps, Local Radio Status Trap.
Status: current Access: read-write
OBJECT-TYPE    
  EnableStatusT  

trapRemAlarmStat 1.3.6.1.4.1.25651.1.2.2.17.13
Remote Alarm Status trap enable(0)/disable(1). This trap is sent when remote radio Status is in errored state (equivalent to the Status LED). See Web, Administration, SNMP, Traps, Remote Radio Status Trap.
Status: current Access: read-write
OBJECT-TYPE    
  EnableStatusT  

trapLocTempStat 1.3.6.1.4.1.25651.1.2.2.17.14
Local Temperature Status trap enable(0)/disable(1). This trap is sent when the internal temperature reaches the warning point. See Web, Administration, SNMP, Traps, Temperature Status Trap.
Status: current Access: read-write
OBJECT-TYPE    
  EnableStatusT  

trapv1Enable 1.3.6.1.4.1.25651.1.2.2.17.15
SNMPv1 Traps enable(0)/disable(1). Enables traps for SNMP protocol version 1. See Web, Administration, SNMP, Traps, Enable SNMPv1 Traps.
Status: current Access: read-write
OBJECT-TYPE    
  EnableStatusT  

trapv2cEnable 1.3.6.1.4.1.25651.1.2.2.17.16
SNMPv2c Traps enable(0)/disable(1). Enables traps for SNMP protocol version 2c. See Web, Administration, SNMP, Traps, Enable SNMPv2c Traps.
Status: current Access: read-write
OBJECT-TYPE    
  EnableStatusT  

trapv3Enable 1.3.6.1.4.1.25651.1.2.2.17.17
SNMPv3 Traps enable(0)/disable(1). Enables traps for SNMP protocol version 3. See Web, Administration, SNMP, Traps, Enable SNMPv3 Traps.
Status: current Access: read-write
OBJECT-TYPE    
  EnableStatusT  

trapLocRslStat 1.3.6.1.4.1.25651.1.2.2.17.18
Local RSL Status trap enable(0)/disable(1). This trap is sent when the local RSL drops below the value set in the RSL Threshold Value (dBm) field. See Web, Administration, SNMP, Traps, Local RSL Status Trap.
Status: current Access: read-write
OBJECT-TYPE    
  EnableStatusT  

trapLocRslThreshold 1.3.6.1.4.1.25651.1.2.2.17.19
Local RSL Threshold. Exalt recommends that this trap be set to a value 5dBm or 10dBm above the threshold as a warning that the system has faded and may be approaching an outage. See Web, Administration, SNMP, Traps, Threshold Value.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

commitSnmpSettings 1.3.6.1.4.1.25651.1.2.2.17.1000
Option strings to be written are: save, clear, correspondingly saving changes to configuration to the persistent storage or clearing unsaved changes.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(4..200)  

ntp 1.3.6.1.4.1.25651.1.2.2.18
NTP and Time zone configuration.
Status: current Access: read-write
OBJECT-IDENTITY    

ntpClientEnable 1.3.6.1.4.1.25651.1.2.2.18.1
this mib to enable/disable the NTP client in the radio. 0 - disable NTP client. 1 - enable with 1 NTP server. 2 - enable with 2 NTP servers. 3 - enable with 3 NTP servers. 4 - enable with 4 NTP servers.
Status: current Access: read-write
OBJECT-TYPE    
  NtpClientEnableT  

ntpServer1IpAddr 1.3.6.1.4.1.25651.1.2.2.18.2
IP address for the first NTP server in xxx.xxx.xxx.xxx format
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(7..15)  

ntpServer2IpAddr 1.3.6.1.4.1.25651.1.2.2.18.3
IP address for the second NTP server in xxx.xxx.xxx.xxx format
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(7..15)  

ntpServer3IpAddr 1.3.6.1.4.1.25651.1.2.2.18.4
IP address for the third NTP server in xxx.xxx.xxx.xxx format
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(7..15)  

ntpServer4IpAddr 1.3.6.1.4.1.25651.1.2.2.18.5
IP address for the forth NTP server in xxx.xxx.xxx.xxx format
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(7..15)  

ntpTimeZoneSelect 1.3.6.1.4.1.25651.1.2.2.18.6
Time Zone selection. 0 - (GMT-11:00) Samoa 1 - (GMT-10.00) Hawaii 2 - (GMT-09:00) Alaska 3 - (GMT-08:00) Pacific Time 4 - (GMT-07:00) Arizona 5 - (GMT-07:00) Montain Time 6 - (GMT-06:00) Central Time 7 - (GMT-05:00) Eastern Time 8 - (GMT-05:00) Indiana (East) 9 - (GMT-04:00) Atlantic Time (Canada) 10- (GMT) Coordinated Universal Time 11- (GMT) London 12- (GMT+01:00) Berlin 13- (GMT+01:00) Belgrade 14- (GMT+01:00) Paris 15- (GMT+02:00) Cairo 16- (GMT+02:00) Helsinki 17- (GMT+03:00) Baghdad 18- (GMT+03:00) Moscow 19- (GMT+03:30) Tehran 20- (GMT+04:30) Kabul 21- (GMT+05:00) Karachi 22- (GMT+07:00) Bangkok 23- (GMT+08:00) Shanghai 24- (GMT+08:00) Taipei 25- (GMT+09:00) Tokyo 26- (GMT+09:00) Seoul 27- (GMT+10:00) Sydney 28- (GMT+10:00) Vladivostok
Status: current Access: read-write
OBJECT-TYPE    
  TimeZoneT  

commitNtpSettings 1.3.6.1.4.1.25651.1.2.2.18.1000
This command allows saving or clear the NTP and Tome Zone configuration. If the save includes the change of time zone, the radio will automatically reboot to take effect the newly selected time zone. Option strings to be written are: save, clear, correspondingly saving changes to configuration to the persistent storage or clearing unsaved changes.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(4..200)  

commitAdminSettings 1.3.6.1.4.1.25651.1.2.2.1000
The Commit Administration settings command. Valid values: 'save', 'clear'. Configuration changes via SNMP do not take effect until 'save' (Commit) command is sent to this parameter. 'clear' (Cancel) command is used to cancel configuration changes before commit operation. In case of invalid configuration this parameter contains text description of the problem.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(4..200)  

radioConfig 1.3.6.1.4.1.25651.1.2.3
The Radio Configuration Section.
Status: current Access: read-write
OBJECT-IDENTITY    

systemConfig 1.3.6.1.4.1.25651.1.2.3.1
This is the device specific configuration section.
Status: current Access: read-write
OBJECT-IDENTITY    

commitSystemSettings 1.3.6.1.4.1.25651.1.2.3.1.1000
The Commit System Configuration settings command. Valid values: 'save', 'clear'. Configuration changes via SNMP do not take effect until 'save' (Commit) command is sent to this parameter. 'clear' (Cancel) command is used to cancel configuration changes before commit operation. In case of invalid configuration this parameter contains text description of the problem.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

interface 1.3.6.1.4.1.25651.1.2.3.2
Radio Interfaces Configuration section.
Status: current Access: read-write
OBJECT-IDENTITY    

te1 1.3.6.1.4.1.25651.1.2.3.2.2
T1,E1 interfaces Configuration section. Section allows to configure T1/E1 ports on the radio if any.
Status: current Access: read-write
OBJECT-IDENTITY    

te1NumChannels 1.3.6.1.4.1.25651.1.2.3.2.2.1
The Number of T1 or E1 channels supported by the Radio.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

te1NumActiveChannels 1.3.6.1.4.1.25651.1.2.3.2.2.2
The Current number of channels available, based on bandwitdh of the RF link and the license key.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

selectT1orE1 1.3.6.1.4.1.25651.1.2.3.2.2.3
Select operation mode of T1/E1 interfaces. Either T1(0) or E1(1). See Web, Configuration, Interface, T1/E1, Set To E1/T1 Mode button.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER t1(0), e1(1)  

te1Interfaces 1.3.6.1.4.1.25651.1.2.3.2.2.4
Attributes for T1 or E1 ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Te1InterfacesEntry

te1Interface 1.3.6.1.4.1.25651.1.2.3.2.2.4.1
An entry in the T1/E1 Attribute table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Te1InterfacesEntry  

te1Status 1.3.6.1.4.1.25651.1.2.3.2.2.4.1.1
The T1/E1 status: enable(1)/disable(0). Parameter allows to enable/disable each individual T1 channel. See Web, Configuration, Interface, T1/E1, Status. To make permanent, write save to commitTe1Settings after change.
Status: current Access: read-write
OBJECT-TYPE    
  Te1StatusT  

t1LBO 1.3.6.1.4.1.25651.1.2.3.2.2.4.1.2
The Line Build Out length range. Valid values (ft): lbo0to133(0), lbo133to266(1), lbo266to399(2), lbo399to533(3), lbo533to655(4). See Web, Configuration, Interface, T1/E1, LBO. To make permanent, write save to commitTe1Settings after change.
Status: current Access: read-write
OBJECT-TYPE    
  Te1LboT  

te1AIS 1.3.6.1.4.1.25651.1.2.3.2.2.4.1.3
The T1/E1 AIS enabled flag: enable(1)/disable(0). If enabled, the radio places an AIS code on the output of the associated interface if and when the link fails or when there is no E1 signal available from the far end to provide the user at the local end. See Web, Configuration, Interface, T1/E1, AIS. To make permanent, write save to commitTe1Settings after change.
Status: current Access: read-write
OBJECT-TYPE    
  Te1StatusT  

t1LineCode 1.3.6.1.4.1.25651.1.2.3.2.2.4.1.4
The T1/E1 Line Code type: b8zs(0), ami(1). See Web, Configuration, Interface, T1/E1, AIS, Line Code. To make permanent, write save to commitTe1Settings after change.
Status: current Access: read-write
OBJECT-TYPE    
  Te1LineCodeT  

te1LoopBackMode 1.3.6.1.4.1.25651.1.2.3.2.2.4.1.5
The Loop Back Mode for a T1/E1 interface. Valid values: disabled(0), ExternalLocal(1), ExternalRemote(2), Internal(3). All loopback configurations control the loop at the Line Interface integrated circuit, which is the device wired directly to the front panel ports. See Web, Configuration, Interface, T1/E1, AIS, Loopback. To make permanent, write save to commitTe1Settings after change.
Status: current Access: read-write
OBJECT-TYPE    
  Te1LoopBackModeT  

commitTe1Settings 1.3.6.1.4.1.25651.1.2.3.2.2.1000
The Commit TE1 Configuration settings command. Valid values: 'save', 'clear'. Configuration changes to TE1 ports via SNMP do not take effect until 'save' (Commit) command is sent to this parameter. 'clear' (Cancel) command is used to cancel configuration changes before commit operation. In case of invalid configuration this parameter contains text description of the problem.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(4..200)  

fileManagement 1.3.6.1.4.1.25651.1.2.3.3
The File Management Section. This section allows to initiate Upload/Download firmware/configuration/logs, perform Firmware activation procedure.
Status: current Access: read-write
OBJECT-IDENTITY    

currentFwFilename 1.3.6.1.4.1.25651.1.2.3.3.1
The file name of the currently running firmware. See Web, Administration, File Management, File Activation, Current File.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

alternateFwFilename 1.3.6.1.4.1.25651.1.2.3.3.2
The file name of the alternate firmware image. See Web, Administration, File Management, File Activation, Alternative File.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

swapFWimage 1.3.6.1.4.1.25651.1.2.3.3.3
Swap the firmware images and restart radio. To perform swap operation 'swap' command needs to be sent to this parameter. For ExtendAirG2 to perform revert to factory operation 'factory' command needs to be sent. Radio will become unavailable for several minutes.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..200)  

fileTransfer 1.3.6.1.4.1.25651.1.2.3.3.4
The File Transfer Section. This section allows to initiate Upload/Download firmware/configuration/logs over TFTP protocol.
Status: current Access: read-write
OBJECT-IDENTITY    

factoryFwFilename 1.3.6.1.4.1.25651.1.2.3.3.5
The file name of the factory firmware image. See Web, Administration, File Management, File Activation, Factory File.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

tftpServerIp 1.3.6.1.4.1.25651.1.2.3.3.4.1
The TFTP Server IP address.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(7..15)  

uploadFilename 1.3.6.1.4.1.25651.1.2.3.3.4.2
The name of the file for upload operation. For configuration file uploadFilename should be always 'config.xml'. uploadFilename value should match the file name in TFTP server folder.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

transferType 1.3.6.1.4.1.25651.1.2.3.3.4.3
The file transfer type. Valid values: - uploadFirmware(0) - uploadConfig(1) - uploadRDD(2) (Valid only for TDD radios) - downloadFirmware(3) - downloadConfig(4) - downloadMIBs(5) - downloadEventLogs(6). The actual operation starts via updating transferStart parameter value.
Status: current Access: read-write
OBJECT-TYPE    
  FileTransferTypeT  

transferStart 1.3.6.1.4.1.25651.1.2.3.3.4.4
TransferStart parameter is used to initiate file transfer operation. Send startTransfer(1) to this parameter.
Status: current Access: read-write
OBJECT-TYPE    
  FileTransferStartT  

transferStatus 1.3.6.1.4.1.25651.1.2.3.3.4.5
The current file transfer status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

radioMonitor 1.3.6.1.4.1.25651.1.2.4
Monitor Various components.
Status: current Access: read-only
OBJECT-IDENTITY    

alarms 1.3.6.1.4.1.25651.1.2.4.2
OBJECT IDENTIFIER    

almLocal 1.3.6.1.4.1.25651.1.2.4.2.3
OBJECT IDENTIFIER    

locSysAlarms 1.3.6.1.4.1.25651.1.2.4.2.3.1
OBJECT IDENTIFIER    

locEthAlarms 1.3.6.1.4.1.25651.1.2.4.2.3.2
OBJECT IDENTIFIER    

locTe1Alarms 1.3.6.1.4.1.25651.1.2.4.2.3.3
OBJECT IDENTIFIER    

locLinkState 1.3.6.1.4.1.25651.1.2.4.2.3.1.1
The Link Status Alarm. Possible values: - almNORMAL(0) - Error-free connection (BER<10e-6) - almMINOR(1) - Errorred connection (BER<10e-3) - almMAJOR(2) - No link (BER>10e-3) See Web, Monitor, Alarms, Link
Status: current Access: read-only
OBJECT-TYPE    
  AlarmLevelT  

locTempAlarm 1.3.6.1.4.1.25651.1.2.4.2.3.1.2
The Temperature Alarm state. Possible values: - almNORMAL(0) - Normal temprature range - almMINOR(1) - Exceeding normal temprature range See Web, Monitor, Alarms, Temperature
Status: current Access: read-only
OBJECT-TYPE    
  AlarmLevelT  

locCurrentTemp 1.3.6.1.4.1.25651.1.2.4.2.3.1.3
The Internal Temperature in Celsius.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

locCurrentTempS 1.3.6.1.4.1.25651.1.2.4.2.3.1.4
The Internal Temperature as a string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

locLinkSecMismatch 1.3.6.1.4.1.25651.1.2.4.2.3.1.9
This is link security mismatch alarm. This alarm tells if the Link Security Key is matching or not. Possible values: - almNORMAL(0) - Link Secutiry keys match - almMAJOR(2) - Link Secutiry keys do not match
Status: current Access: read-only
OBJECT-TYPE    
  AlarmLevelT  

locLinkStateV 1.3.6.1.4.1.25651.1.2.4.2.3.1.15
Vertical Link Status Alarm. -<>
Status: current Access: read-only
OBJECT-TYPE    
  AlarmLevelT  

locLinkStateH 1.3.6.1.4.1.25651.1.2.4.2.3.1.16
Horizontal Link Status Alarm. -<>
Status: current Access: read-only
OBJECT-TYPE    
  AlarmLevelT  

locTe1LinkSummary 1.3.6.1.4.1.25651.1.2.4.2.3.3.1
The T1/E1 Link Summary LED color.
Status: current Access: read-only
OBJECT-TYPE    
  Led4ColorT  

locTE1Alarms 1.3.6.1.4.1.25651.1.2.4.2.3.3.2
The Local T1/E1 Interface Alarms.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Te1Alarms1Entry

locTe1AlarmsEntry 1.3.6.1.4.1.25651.1.2.4.2.3.3.2.1
T1/E1 Alarms table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Te1Alarms1Entry  

locTe1Alarm 1.3.6.1.4.1.25651.1.2.4.2.3.3.2.1.1
The Alarms state for the Local T1/E1 Channel. Possible values: - almNORMAL(0) - Enabled and connection present - almMAJOR(2) - Enabled and no connection present - almDisable(3) - Disabled and no connection present - almNotAvailable(4) - T1/E1 channel is not available See Web, Monitor, Alarms, T1/E1 Input
Status: current Access: read-only
OBJECT-TYPE    
  AlarmLevelT  

almRemote 1.3.6.1.4.1.25651.1.2.4.2.4
OBJECT IDENTIFIER    

remSysAlarms 1.3.6.1.4.1.25651.1.2.4.2.4.1
OBJECT IDENTIFIER    

remEthAlarms 1.3.6.1.4.1.25651.1.2.4.2.4.2
OBJECT IDENTIFIER    

remTe1Alarms 1.3.6.1.4.1.25651.1.2.4.2.4.3
OBJECT IDENTIFIER    

remLinkState 1.3.6.1.4.1.25651.1.2.4.2.4.1.1
The Link Status Alarm for far end radio. Possible values: - almNORMAL(0) - Error-free connection (BER<10e-6) - almMINOR(1) - Errorred connection (BER<10e-3) - almMAJOR(2) - No link (BER>10e-3) - almNotAvailable(4) - Telemetry is down See Web, Monitor, Alarms, Link
Status: current Access: read-only
OBJECT-TYPE    
  AlarmLevelT  

remTempAlarm 1.3.6.1.4.1.25651.1.2.4.2.4.1.2
The Temperature Alarm state for far end radio. Possible values: - almNORMAL(0) - Normal temprature range - almMINOR(1) - Exceeding normal temprature range - almNotAvailable(4) - Telemetry is down See Web, Monitor, Alarms, Temperature
Status: current Access: read-only
OBJECT-TYPE    
  AlarmLevelT  

remCurrentTemp 1.3.6.1.4.1.25651.1.2.4.2.4.1.3
The Internal Temperature in Celsius for far end radio.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

remCurrentTempS 1.3.6.1.4.1.25651.1.2.4.2.4.1.4
The internal Temperature as a string for far end radio.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

remLinkSecMismatch 1.3.6.1.4.1.25651.1.2.4.2.4.1.9
This is link security mismatch alarm. This alarm tells if the Link Security Key is matching or not. Possible values: - almNORMAL(0) - Link Secutiry keys match - almMAJOR(2) - Link Secutiry keys do not match - almNotAvailable(4) - Telemetry is down
Status: current Access: read-only
OBJECT-TYPE    
  AlarmLevelT  

remLinkStateV 1.3.6.1.4.1.25651.1.2.4.2.4.1.15
Vertical Link Status Alarm. -<>
Status: current Access: read-only
OBJECT-TYPE    
  AlarmLevelT  

remLinkStateH 1.3.6.1.4.1.25651.1.2.4.2.4.1.16
Horizontal Link Status Alarm. -<>
Status: current Access: read-only
OBJECT-TYPE    
  AlarmLevelT  

remTe1LinkSummary 1.3.6.1.4.1.25651.1.2.4.2.4.3.1
The T1/E1 Link Summary LED color.
Status: current Access: read-only
OBJECT-TYPE    
  Led4ColorT  

remTE1Alarms 1.3.6.1.4.1.25651.1.2.4.2.4.3.2
The Remotel T1/E1 Interface Alarms.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Te1AlarmsEntry

remTe1AlarmsEntry 1.3.6.1.4.1.25651.1.2.4.2.4.3.2.1
T1/E1 Alarms table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Te1AlarmsEntry  

remTe1Alarm 1.3.6.1.4.1.25651.1.2.4.2.4.3.2.1.1
The Alarms state for the Local T1/E1 Channel of far end radio. Possible values: - almNORMAL(0) - Enabled and connection present - almMAJOR(2) - Enabled and no connection present - almDisable(3) - Disabled and no connection present - almNotAvailable(4) - Telemetry is down or T1/E1 channel is not available See Web, Monitor, Alarms, T1/E1 Input
Status: current Access: read-only
OBJECT-TYPE    
  AlarmLevelT  

performance 1.3.6.1.4.1.25651.1.2.4.3
OBJECT IDENTIFIER    

perfLocal 1.3.6.1.4.1.25651.1.2.4.3.1
OBJECT IDENTIFIER    

perfRemote 1.3.6.1.4.1.25651.1.2.4.3.2
OBJECT IDENTIFIER    

locCurrentBER 1.3.6.1.4.1.25651.1.2.4.3.1.1
The Curent Bit-Error Rate as scaled integer for local radio. The BER multiplied by 1,000,000. If the link is operating perfectly, this should indicate zero. See Web, Monitor, Performance, Current BER
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

locCurrentBERstr 1.3.6.1.4.1.25651.1.2.4.3.1.2
The Current Bit-Error Rate as a string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

locCurrentRSL 1.3.6.1.4.1.25651.1.2.4.3.1.3
Current RSL is the measurement of the received signal level. When the RSL falls below the threshold specification, the link disconnects and will not reconnect until the RSL is above the threshold specification. See Web, Monitor, Performance, Current RSL
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

locCurrentRSLstr 1.3.6.1.4.1.25651.1.2.4.3.1.4
The Current RSL as a string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

locErrorDuration 1.3.6.1.4.1.25651.1.2.4.3.1.5
The Error Duration indicates the total number of seconds that occurred where there was at least one bit error since the last time that the radio statistics counter was reset. See Web, Monitor, Performance, Errored Seconds
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

locErrorDurationStr 1.3.6.1.4.1.25651.1.2.4.3.1.6
The Error Duration as a formatted string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

locUnavailDuration 1.3.6.1.4.1.25651.1.2.4.3.1.7
Unavailable Duration keeps track of every second where the BER equals or exceeds 1x10-3, as well as any seconds where there is a complete loss of radio communication. See Web, Monitor, Performance, Unavailable Seconds
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

locUnavailDurationStr 1.3.6.1.4.1.25651.1.2.4.3.1.8
The Unavailable Duration as a formatted string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

locMinRSL 1.3.6.1.4.1.25651.1.2.4.3.1.9
The Minimum RSL indicates the worst (lowest) received signal level that occurred since the last counter reset. See Web, Monitor, Performance, Minimum RSL
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

locMinRSLstr 1.3.6.1.4.1.25651.1.2.4.3.1.10
The Minimum RSL value as a string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

locMinRSLtimestamp 1.3.6.1.4.1.25651.1.2.4.3.1.11
The Minimum RSL Timestamp indicates the date and time when the Minimum RSL occurred. See Web, Monitor, Performance, Minimum RSL Timestamp
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

locMaxRSL 1.3.6.1.4.1.25651.1.2.4.3.1.12
The Maximum RSL indicates the best (highest) RSL that occurred since the last counter reset. See Web, Monitor, Performance, Maximum RSL
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

locMaxRSLstr 1.3.6.1.4.1.25651.1.2.4.3.1.13
The Maximum RSL level As string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

locSampleDuration 1.3.6.1.4.1.25651.1.2.4.3.1.14
The Sample Duration indicates the amount of time passed since the last counter reset. See Web, Monitor, Performance, Time Since Reset
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

locSampleDurationStr 1.3.6.1.4.1.25651.1.2.4.3.1.15
The Sample Duration value as a formatted string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

locEthPerfInterfaces 1.3.6.1.4.1.25651.1.2.4.3.1.16
Performance characteristics of local Ethernet interfaces
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LocEthPerfInterfacesEntry

locEthPerfInterfacesEntry 1.3.6.1.4.1.25651.1.2.4.3.1.16.1
An entry in the Performance characteristics of local Ethernet interfaces table
Status: current Access: not-accessible
OBJECT-TYPE    
  LocEthPerfInterfacesEntry  

locEthUtilizationIn 1.3.6.1.4.1.25651.1.2.4.3.1.16.1.1
Inbound ethernet utilization (%). See Web, Analysis, Ethernet Utilization.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

locEthUtilizationOut 1.3.6.1.4.1.25651.1.2.4.3.1.16.1.2
Outbound ethernet utilization (%). See Web, Analysis, Ethernet Utilization.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

locEthSpeed 1.3.6.1.4.1.25651.1.2.4.3.1.16.1.3
Current Ethernet Speed. See Web, Monitor, Ethernet Performance.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

locEthUtilizationWatermarkEnabled 1.3.6.1.4.1.25651.1.2.4.3.1.17
Ethernet utilization watermark enable(1)/disable(0). See Web, Analysis, Ethernet Utilization, Ethernet Utilization Watermark.
Status: current Access: read-write
OBJECT-TYPE    
  ExaltEnableT  

locEthUtilizationWatermark 1.3.6.1.4.1.25651.1.2.4.3.1.18
Ethernet utilization watermark level (%). See Web, Analysis, Ethernet Utilization, Watermark level.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

locEthUtilizationWatermarkTrapEnabled 1.3.6.1.4.1.25651.1.2.4.3.1.19
Ethernet utilization watermark trap enable(1)/disable(0). The watermark trap function allows administrators to receive an SNMP trap when watermark conditions are exceeded. See Web, Analysis, Ethernet Utilization, Enable Ethernet Utilization Trap.
Status: current Access: read-write
OBJECT-TYPE    
  ExaltEnableT  

locEthUtilizationWatermarkTrapDuration 1.3.6.1.4.1.25651.1.2.4.3.1.20
Ethernet utilization trap limit in minutes/day (0-1440 minutes). See Web, Analysis, Ethernet Utilization, Send trap if watermark hit duration exceeds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1440  

locMaximumTxModulation 1.3.6.1.4.1.25651.1.2.4.3.1.100
The highest/maximum Tx modulation when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Tx modulation.
Status: current Access: read-only
OBJECT-TYPE    
  AcmModulationT  

locActiveTxModulation 1.3.6.1.4.1.25651.1.2.4.3.1.101
The active Tx modulation when ACM is enabled. See Web, Monitor, Performance, Tx modulation.
Status: current Access: read-only
OBJECT-TYPE    
  AcmModulationT  

locMinimumTxModulation 1.3.6.1.4.1.25651.1.2.4.3.1.102
The lowest/minimum Tx modulation when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Tx modulation.
Status: current Access: read-only
OBJECT-TYPE    
  AcmModulationT  

locMaximumRxModulation 1.3.6.1.4.1.25651.1.2.4.3.1.103
The highest/maximum Rx modulation when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Rx modulation.
Status: current Access: read-only
OBJECT-TYPE    
  AcmModulationT  

locActiveRxModulation 1.3.6.1.4.1.25651.1.2.4.3.1.104
The active Rx modulation when ACM is enabled. See Web, Monitor, Performance, Rx modulation.
Status: current Access: read-only
OBJECT-TYPE    
  AcmModulationT  

locMinimumRxModulation 1.3.6.1.4.1.25651.1.2.4.3.1.105
The lowest/minimum Rx modulation when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Rx modulation.
Status: current Access: read-only
OBJECT-TYPE    
  AcmModulationT  

locMaximumTxEthernetThroughput 1.3.6.1.4.1.25651.1.2.4.3.1.106
The highest/maximum Tx Ethernet throughput in Mbps when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Tx Ethernet Throughput.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

locActiveTxEthernetThroughput 1.3.6.1.4.1.25651.1.2.4.3.1.107
The active Tx Ethernet throughput in Mbps when ACM is enabled. See Web, Monitor, Performance, Tx Ethernet Throughput.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

locMinimumTxEthernetThroughput 1.3.6.1.4.1.25651.1.2.4.3.1.108
The lowest/minimum Tx Ethernet throughput in Mbps when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Tx Ethernet Throughput.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

locMaximumRxEthernetThroughput 1.3.6.1.4.1.25651.1.2.4.3.1.109
The highest/maximum Rx Ethernet throughput in Mbps when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Rx Ethernet Throughput.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

locActiveRxEthernetThroughput 1.3.6.1.4.1.25651.1.2.4.3.1.110
The active Rx Ethernet throughput in Mbps when ACM is enabled. See Web, Monitor, Performance, Rx Ethernet Throughput.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

locMinimumRxEthernetThroughput 1.3.6.1.4.1.25651.1.2.4.3.1.111
The lowest/minimum Rx Ethernet throughput in Mbps when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Rx Ethernet Throughput.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

locResetStats 1.3.6.1.4.1.25651.1.2.4.3.1.1000
Write 'reset' to locResetStats to clear the Performance statistics.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

remCurrentBER 1.3.6.1.4.1.25651.1.2.4.3.2.1
The Curent Bit-Error Rate as scaled integer for far end radio. The BER multiplied by 1,000,000. If the link is operating perfectly, this should indicate zero. See Web, Monitor, Performance, Current BER
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

remCurrentBERstr 1.3.6.1.4.1.25651.1.2.4.3.2.2
The Current Bit-Error Rate as a string. Far end radio
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

remCurrentRSL 1.3.6.1.4.1.25651.1.2.4.3.2.3
Current RSL is the measurement of the received signal level. When the RSL falls below the threshold specification, the link disconnects and will not reconnect until the RSL is above the threshold specification. See Web, Monitor, Performance, Current RSL
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

remCurrentRSLstr 1.3.6.1.4.1.25651.1.2.4.3.2.4
The Current RSL as a string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

remErrorDuration 1.3.6.1.4.1.25651.1.2.4.3.2.5
The Error Duration indicates the total number of seconds that occurred where there was at least one bit error since the last time that the radio statistics counter was reset. See Web, Monitor, Performance, Errored Seconds, Remote column.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

remErrorDurationStr 1.3.6.1.4.1.25651.1.2.4.3.2.6
The Error Duration as a formatted string. Far end radio.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

remUnavailDuration 1.3.6.1.4.1.25651.1.2.4.3.2.7
Unavailable Duration keeps track of every second where the BER equals or exceeds 1x10-3, as well as any seconds where there is a complete loss of radio communication. See Web, Monitor, Performance, Unavailable Seconds
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

remUnavailDurationStr 1.3.6.1.4.1.25651.1.2.4.3.2.8
The Unavailable Duration as a formatted string. Far end radio.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

remMinRSL 1.3.6.1.4.1.25651.1.2.4.3.2.9
The Minimum RSL indicates the worst (lowest) received signal level that occurred since the last counter reset. See Web, Monitor, Performance, Minimum RSL, Remote column.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

remMinRSLstr 1.3.6.1.4.1.25651.1.2.4.3.2.10
The Minimum RSL value as a string. Far end radio.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

remMinRSLtimestamp 1.3.6.1.4.1.25651.1.2.4.3.2.11
The Minimum RSL Timestamp indicates the date and time when the Minimum RSL occurred. See Web, Monitor, Performance, Minimum RSL Timestamp, Remote column.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

remMaxRSL 1.3.6.1.4.1.25651.1.2.4.3.2.12
The Maximum RSL indicates the best (highest) RSL that occurred since the last counter reset. See Web, Monitor, Performance, Maximum RSL, Remote column.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

remMaxRSLstr 1.3.6.1.4.1.25651.1.2.4.3.2.13
The Maximum RSL level As string. Far end radio.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

remSampleDuration 1.3.6.1.4.1.25651.1.2.4.3.2.14
The Sample Duration indicates the amount of time passed since the last counter reset. See Web, Monitor, Performance, Time Since Reset, Remote column.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

remSampleDurationStr 1.3.6.1.4.1.25651.1.2.4.3.2.15
The Sample Duration value as a formatted string. Far end radio.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

remResetStats 1.3.6.1.4.1.25651.1.2.4.3.2.1000
Write 'reset' to remResetStats to clear the Performance statistics.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

userThroughput 1.3.6.1.4.1.25651.1.2.4.5
OBJECT IDENTIFIER    

aggregateUserThroughput 1.3.6.1.4.1.25651.1.2.4.5.1
Aggregated User Throughput. For FDD radios this parameter is always equal to fullDuplexEthernetThroughput.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

inboundEthernetThroughput 1.3.6.1.4.1.25651.1.2.4.5.2
Inbound Ethernet Throughput. For FDD radios this parameter is always N/A.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

outboundEthernetThroughput 1.3.6.1.4.1.25651.1.2.4.5.3
Outbound Ethernet Throughput. For FDD radios this parameter is always N/A.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

fullDuplexEthernetThroughput 1.3.6.1.4.1.25651.1.2.4.5.4
The Full Duplex Ethernet Throughput is determined by the combination of settings for Mode and Bandwidth. See Web, Monitor, User Throughput, Full Duplex Ethernet Throughput.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

radioReboot 1.3.6.1.4.1.25651.1.2.1000
Reboot the radio device. Send 'reboot' to radioReboot parameter to reboot the radio device.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..100)  

productsMIBConformance 1.3.6.1.4.1.25651.1.3
OBJECT IDENTIFIER    

productsMIBCompliances 1.3.6.1.4.1.25651.1.3.1
OBJECT IDENTIFIER    

productsMIBGroups 1.3.6.1.4.1.25651.1.3.2
OBJECT IDENTIFIER    

productsAllObjects 1.3.6.1.4.1.25651.1.3.2.1
This automatically created object group contains all those objects that do not belong to any other OBJECT-GROUP
Status: current Access: read-write
OBJECT-GROUP