FH800u-MIB

File: FH800u-MIB.mib (53310 bytes)

Imported modules

RFC-1215 RFC1155-SMI RFC1213-MIB

Imported symbols

TRAP-TYPE enterprises OBJECT-TYPE
Counter TimeTicks IpAddress
DisplayString PhysAddress

Defined Types

GroupEntry  
SEQUENCE    
  groupID INTEGER
  groupType INTEGER
  groupCounterReset INTEGER
  groupPosition INTEGER
  groupRptrHwVer INTEGER
  groupRptrSerialNo PhysAddress
  groupSysMajorVer INTEGER
  groupSysMinorVer INTEGER
  groupPostCodeMajorVer INTEGER
  groupPostCodeMinorVer INTEGER
  groupAgentStatus INTEGER
  groupAgentHwVer INTEGER
  groupAgentSerialNo PhysAddress
  groupAgentPhysAddr PhysAddress
  groupAgentBootupOption INTEGER
  groupAgentBaudrate INTEGER

PortEntry  
SEQUENCE    
  portGroupID INTEGER
  portID INTEGER
  portSpeed INTEGER
  portSpeedConfig INTEGER
  portSegmtID INTEGER

RmonConfigEntry  
SEQUENCE    
  rmonConfigSegmtID INTEGER
  rmonConfigStatus INTEGER

PerfMonSegmentEntry  
SEQUENCE    
  segmentPerfID INTEGER
  segmentCRCErrors Counter
  segmentAlignmentErrors Counter
  segmentCollisions Counter
  segmentTotalPortIsolates Counter
  segmentSymbolErrors Counter

SwitchPortStatsEntry  
SEQUENCE    
  switchPortStatsGroupID INTEGER
  switchPortStatsID INTEGER
  switchPortReadableFrames Counter
  switchPortReadableOctets Counter
  switchPortFCSErrors Counter
  switchPortAlignmentErrors Counter
  switchPortFramesTooLong Counter
  switchPortShortEvents Counter
  switchPortRunts Counter
  switchPortCollisions Counter
  switchPortLateEvents Counter
  switchPortVeryLongEvents Counter
  switchPortDataRateMismatches Counter
  switchPortBroadcastPackets Counter
  switchPortMulticastPackets Counter

SecurityPortEntry  
SEQUENCE    
  securityPortGroupID INTEGER
  securityPortID INTEGER
  securityPortAddr PhysAddress
  securityAutoLearnAction INTEGER
  securityPortIntrusion INTEGER

Defined Values

alliedTelesyn 1.3.6.1.4.1.207
OBJECT IDENTIFIER    

products 1.3.6.1.4.1.207.1
OBJECT IDENTIFIER    

dualHub 1.3.6.1.4.1.207.1.10
OBJECT IDENTIFIER    

fh812u 1.3.6.1.4.1.207.1.10.1
OBJECT IDENTIFIER    

fh824u 1.3.6.1.4.1.207.1.10.2
OBJECT IDENTIFIER    

mibObject 1.3.6.1.4.1.207.8
OBJECT IDENTIFIER    

repeaterMib 1.3.6.1.4.1.207.8.1
OBJECT IDENTIFIER    

newRepeaterMib 1.3.6.1.4.1.207.8.1.20
OBJECT IDENTIFIER    

acctonHubMIB 1.3.6.1.4.1.207.8.1.20.3
OBJECT IDENTIFIER    

atactDualHubMgt 1.3.6.1.4.1.207.8.1.20.3.11
OBJECT IDENTIFIER    

fh800uMgt 1.3.6.1.4.1.207.8.1.20.3.11.1
OBJECT IDENTIFIER    

fh800uBasicCapability 1.3.6.1.4.1.207.8.1.20.3.11.1.1
OBJECT IDENTIFIER    

fh800uPerfMonCapability 1.3.6.1.4.1.207.8.1.20.3.11.1.2
OBJECT IDENTIFIER    

fh800uSwitchCapability 1.3.6.1.4.1.207.8.1.20.3.11.1.3
OBJECT IDENTIFIER    

fh800uSecurityCapability 1.3.6.1.4.1.207.8.1.20.3.11.1.5
OBJECT IDENTIFIER    

fh800uStackInfo 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1
OBJECT IDENTIFIER    

stackInusedIP 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.1
The IP address currently used by the Dual-Speed Hub system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

stackInusedNetMask 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.2
The subnet maskcurrently used by the Dual-Speed Hub system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

stackInusedGateway 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.3
The prefered gateway used to send traps.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

stackInusedServerSlipAddr 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.4
The Server SLIP addresscurrently used by the Dual-Speed Hub system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

stackInusedHostSlipAddr 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.5
The Host SLIP address currently used by the Dual-Speed Hub system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

stackInusedBootUpIP 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.6
The Bootup IP address currently used by the Dual-Speed Hub system. The Bootup IP must reside in the same subnet as the stackIP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

stackTemporalIP 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.7
Used to change the IP address of the Dual-Speed Hub system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

stackTemporalNetMask 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.8
Used to change the subnet mask of the Dual-Speed Hub system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

stackTemporalGateway 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.9
Used to change the prefered gateway to send traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

stackTemporalServerSlipAddr 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.10
Used to change the Server SLIP address of the Dual-Speed Hub system. The SLIP address must reside in the same subnet as the stackIP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

stackTemporalHostSlipAddr 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.11
Used to change the Host SLIP address of the Dual-Speed Hub system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

stackTemporalBootUpIP 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.12
Used to change the Bootup IP address of the Dual-Speed Hub system. The Bootup IP must reside in the same subnet as the stackIP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipInformationReset 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.13
Setting the stackIP, stackNetMask,stackGateway, stackSlipAddr, and stackBootUpIP will not immediately enable parameters take effect . They will take effect when ipInformationReset is set to reset(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noReset(1), reset(2)  

stackHealthMonitor 1.3.6.1.4.1.207.8.1.20.3.11.1.1.1.14
< FOR fh800u Dual-Speed Hub DEFINITION : > There are two kinds of hubs : 12 ports need (1+ 12 + 1 + 1 + 1 + 1 +1 +1 +1) 20 bytes and 24 ports need (1+ 24 + 1 + 1 + 1 + 1 +1 +1 +1) 32 bytes The maximun size : 256 bytes (total for 8 hubs)=8 hub * (1+ 24 + 1 + 1 + 1 +1 +1 +1 +1) bytes | byte256 byte255......................byte2 byte1 | bit7 bit6 ... bit1 bit0 Use the first byte of each hub to indicate whether 20 or 32 bytes is used. BYTE 1: total number of ports on a hub 00001100 : 12 ports | | bit7... bit0 00011000 : 24 ports | | bit7... bit0 For 12-port hub BYTE 2 - 13 : port status for port 1 - 12 *BYTE 2 : port status for port 1 bit 0-4 : LED status bit 0 : link status 0 - no link; 1 - link bit 1 : partition status 0 - no part.; 1 - part. bit 2 : port operation status 0 - disabled; 1 - enabled bit 3-4 : port type status 00 - not present 01 - tenMb 10 - onehundredMb 11 - reserved bit 5-7 : reserved BYTE 14-25 :reserved BYTE 26 : Expansion Port (EP) status1 bit 0-2: EP Type 000 - not present 100 - 100BASE-TX(ST) FEM 010 - 100BASE-TX(SC) FEM 1001 to 1111 - reserved bit 3-4 : FEM forwarding mode status Applicable only to FEM module 00 - adaptive cut through 01 - reserved 10 - reserved 11 - store and forward bit 5: FEM back pressure status 0 - disabled; 1 - enabled bit 6-7 : reserved BYTE 27 : Expansion Port (EP) status2 bit 0-1 : LED status bit 0 : FEM link status 0 - no link; 1 - link bit 1 : FEM half/full duplex status 0 - full duplex; 1 - half duplex bit 2 : EP collision led status 0 - off; 1 - on bit 3-4 : bit 3 : tx LED status 0 - off; 1 - tx on bit 4 : rx LED status 0 - off; 1 - rx on bit 5-7 : reserved BYTE 28 : tenMb segment traffic/collision bit 0-1 : tenMb traffic LED status 00 - no traffic 01 - low traffic 10 - middle traffic 11 - high traffic bit 2-5 : tenMb collision LED status 0000 - none 0001 - 1 % 0010 - 3 % 0011 - 5 % 0100 - 10 % 0101 - >= 15 % bit 6-7 : reserved BYTE 29 : onehundredMb segment traffic/collision /Power/Switch LED status bit 0-1 : onehundredMb traffic LED status 00 - no traffic 01 - low traffic 10 - middle traffic 11 - high traffic bit 2-5 : onehundredMb collision LED status 0000 - none 0001 - 1 % 0010 - 3 % 0011 - 5 % 0100 - 10 % 0101 - >= 15 % bit 6 : Power LED 0 - OFF; 1 - ON bit 7 : Switch LED 0 - OFF; 1 - ON BYTE 30 :SNMP agent & switch status bit 0: internal switch bit 0 - not exist; 1 - exist bit 1: internal switch status 0 - inactive; 1 - active bit 2: expension switch bit 0 - bad; 1 - good bit 3: expension switch status 0 - inactive; 1 - active bit 4: agent bit 0 - not exist; 1 - exist bit 5 : master status 0 - Slave; 1 - Master bit 6 - 7 : reserved BYTE 31 : Rmon status bit 0 : rmon bit 0 - not exist; 1 - exist bit 1 - 2 :rmon segment 00 - all stack 01 - segment tenMb 10 - segment onehundredMb 11 - reserved bit 3 - 5 : RMON group Status 000 - not-present 001 - disabled 010 - Rmon-4Group 011 - Rmon-7Group 100 - Rmon-all 101 to 111 - reserved bit 6 -7 : reserved BYTE 32 : Hub Position(Hub ID)/Bus Termination bit 0 - 3 : hub position 0000 - invalid 0001 - 1 0010 - 2 0011 - 3 0100 - 4 0101 - 5 0110 - 6 0111 - 7 1000 - 8 1001 to 1111 - reserved bit 4 : termination status 0 - not end hub 1 - end hub in the stack bit 5 - 7 : reserved For 24-port hub BYTE 2 - 25 : port status for port 1 - 24 *BYTE 2 : port status for port 1 bit 0-4 : LED status bit 0 : link status 0 - no link; 1 - link bit 1 : partition status 0 - no part.; 1 - part. bit 2 : port operation status 0 - disabled; 1 - enabled bit 3-4 : port type status 00 - not present 01 - tenMb 10 - onehundredMb 11 - reserved bit 5-7 : reserved BYTE 26 : Expansion Port (EP) status1 bit 0-2: EP Type 000 - not present 100 - 100BASE-TX(ST) FEM 010 - 100BASE-TX(SC) FEM 1001 to 1111 - reserved bit 3-4 : FEM forwarding mode status Applicable only to FEM module 00 - adaptive cut through 01 - reserved 10 - reserved 11 - store and forward bit 5: FEM back pressure status 0 - disabled; 1 - enabled bit 6-7 : reserved BYTE 27 : Expansion Port (EP) status2 bit 0-1 : LED status bit 0 : FEM link status 0 - no link; 1 - link bit 1 : FEM half/full duplex status 0 - full duplex; 1 - half duplex bit 2 : EP collision led status 0 - off; 1 - on bit 3-4 : bit 3 : tx LED status 0 - off; 1 - tx on bit 4 : rx LED status 0 - off; 1 - rx on bit 5-7 : reserved BYTE 28 : tenMb segment traffic/collision bit 0-1 : tenMb traffic LED status 00 - no traffic 01 - low traffic 10 - middle traffic 11 - high traffic bit 2-5 : tenMb collision LED status 0000 - none 0001 - 1 % 0010 - 3 % 0011 - 5 % 0100 - 10 % 0101 - >= 15 % bit 6-7 : reserved BYTE 29 : onehundredMb segment traffic/collision /Power/Switch LED status bit 0-1 : onehundredMb traffic LED status 00 - no traffic 01 - low traffic 10 - middle traffic 11 - high traffic bit 2-5 : onehundredMb collision LED status 0000 - none 0001 - 1 % 0010 - 3 % 0011 - 5 % 0100 - 10 % 0101 - >= 15 % bit 6 : Power LED 0 - OFF; 1 - ON bit 7 : Switch LED 0 - OFF; 1 - ON BYTE 30 :SNMP agent & switch status bit 0: internal switch bit 0 - not exist; 1 - exist bit 1: internal switch status 0 - inactive; 1 - active bit 2: expension switch bit 0 - bad; 1 - good bit 3: expension switch status 0 - inactive; 1 - active bit 4: agent bit 0 - not exist; 1 - exist bit 5 : master status 0 - Slave; 1 - Master bit 6 - 7 : reserved BYTE 31 : Rmon status bit 0 : rmon bit 0 - not exist; 1 - exist bit 1 - 2 :rmon segment 00 - all stack 01 - segment tenMb 10 - segment onehundredMb 11 - reserved bit 3 - 5 : RMON group Status 000 - not-present 001 - disabled 010 - Rmon-4Group 011 - Rmon-7Group 100 - Rmon-all 101 to 111 - reserved bit 6 -7 : reserved BYTE 32 : Hub Position(Hub ID)/Bus Termination bit 0 - 3 : hub position 0000 - invalid 0001 - 1 0010 - 2 0011 - 3 0100 - 4 0101 - 5 0110 - 6 0111 - 7 1000 - 8 1001 to 1111 - reserved bit 4 : termination status 0 - not end hub 1 - end hub in the stack bit 5 - 7 : reserved
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(256)  

fh800uGroupInfo 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2
OBJECT IDENTIFIER    

groupTable 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1
A group means a hub unit
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GroupEntry

groupEntry 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GroupEntry  

groupID 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.1
The ID number of a hub unit, used to select it
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

groupType 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.2
Type of hub unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER fh824u(1), fh812u(2), eh3024a(3), eh3012a(4)  

groupCounterReset 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.3
Write any value to this variable to reset the counters of the hub unit. 2 is a value commonly used to reset things
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noReset(1), reset(2)  

groupPosition 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.4
Physical position of a hub unit in top-down order, only supported if hardware permits such as Dual-Speed Hub systems
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

groupRptrHwVer 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.5
Hardware version of the repeater board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

groupRptrSerialNo 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.6
Serial number of the repeater board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

groupSysMajorVer 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.7
Microcode major version of this hub.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

groupSysMinorVer 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.8
Microcode minor version of this hub.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

groupPostCodeMajorVer 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.9
POST microcode major version of this hub.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

groupPostCodeMinorVer 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.10
POST microcode minor version of this hub.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

groupAgentStatus 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.11
Status of this hub agent. Each stack allows an SNMP primary agent. primary(2): The agent in this stack is a primary agent. backup(3): The agent in this stack is a backup agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-present(1), primary(2), backup(3)  

groupAgentHwVer 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.12
Hardware version of the agent board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

groupAgentSerialNo 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.13
Serial number of the agent board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

groupAgentPhysAddr 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.14
MAC address of this hub agent
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

groupAgentBootupOption 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.15
This variable defines how to start the microcode in the segment. normal(1): Use NVRAM information and flash ROM microcode to start up the system. tftp-download(2): Always download the new version of microcode into RAM and start it. bootp-get-ip(3): Get the IP information from the BootP server, and then start up the microcode in flash ROM. bootp-download(4): Get the IP information from the BootP server, and then download the microcode from the TFTP server. bootp-upgrade(5): Get the IP information from the BootP server, and then download the microcode from the TFTP server. After the download has been completed, upgrade the microcode in system flash ROM.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), tftp-download(2), bootp-get-ip(3), bootp-download(4), bootp-upgrade(5)  

groupAgentBaudrate 1.3.6.1.4.1.207.8.1.20.3.11.1.1.2.1.1.16
Baud rate of the console port
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER baud-9600(1), baud-14400(2), baud-19200(3), baud-38400(4), baud-57600(5), baud-115200(6)  

fh800uPortInfo 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3
OBJECT IDENTIFIER    

portTable 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3.1
information about ports in a system. Each port belongs to a group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortEntry

portEntry 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PortEntry  

portGroupID 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3.1.1.1
ID of the hub unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

portID 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3.1.1.2
ID of the port unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

portSpeed 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3.1.1.3
Ethernet connector type of a port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER tenMb(1), onehundredMbClassI(2), onehundredMbClassII(3), other(4)  

portSpeedConfig 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3.1.1.4
Select the Ethernet connector type of a port
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER tenMb(1), onehundredMbClassI(2), onehundredMbClassII(3), autoDetected(4)  

portSegmtID 1.3.6.1.4.1.207.8.1.20.3.11.1.1.3.1.1.5
ID of the Segment unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

fh800uSegmentInfo 1.3.6.1.4.1.207.8.1.20.3.11.1.1.4
OBJECT IDENTIFIER    

fh800uRmonConfig 1.3.6.1.4.1.207.8.1.20.3.11.1.1.5
OBJECT IDENTIFIER    

nicAttachSegment 1.3.6.1.4.1.207.8.1.20.3.11.1.1.5.1
The value represents the segment that the NIC is attached to.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

fullRmonSegment 1.3.6.1.4.1.207.8.1.20.3.11.1.1.5.2
The value shows if the segment supports all rmon or only 4 rmon groups.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

rmonConfigTable 1.3.6.1.4.1.207.8.1.20.3.11.1.1.5.3
RMON configuration table information; the index is the ID of of the segment the rmon montioring .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RmonConfigEntry

rmonConfigEntry 1.3.6.1.4.1.207.8.1.20.3.11.1.1.5.3.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RmonConfigEntry  

rmonConfigSegmtID 1.3.6.1.4.1.207.8.1.20.3.11.1.1.5.3.1.1
ID of the Segment rmon is montioring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

rmonConfigStatus 1.3.6.1.4.1.207.8.1.20.3.11.1.1.5.3.1.2
Status of this RMON segment.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fh800uPerfMonSegmentInfo 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3
OBJECT IDENTIFIER    

perfMonSegmentTable 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1
Tok_String
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PerfMonSegmentEntry

perfMonSegmentEntry 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PerfMonSegmentEntry  

segmentPerfID 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1.1.1
ID used to select a segment
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

segmentCRCErrors 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1.1.2
Total CRC errors received by a segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

segmentAlignmentErrors 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1.1.3
Total frame alignment errors received by a segment
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

segmentCollisions 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1.1.4
Total collisions received in a segment
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

segmentTotalPortIsolates 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1.1.5
Total isolated ports in a segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

segmentSymbolErrors 1.3.6.1.4.1.207.8.1.20.3.11.1.2.3.1.1.6
Total frame symbol errors received by a segment
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

fh800uSwitchStatsInfo 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1
OBJECT IDENTIFIER    

switchPortStatsTable 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1
This table provides statistics on each port on each switch module in the stack. Note that statistics for the external port on media and switch/media modules are unavailable to the agent and are reported as 0. Statistics for port 2 (the internal 10Mbps port) on media modules are also reported as 0.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwitchPortStatsEntry

switchPortStatsEntry 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwitchPortStatsEntry  

switchPortStatsGroupID 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.1
The group ID of the switch module port being referenced. If the group is not present, or if there is no switch module installed in the group, GetRequests and SetRequests are rejected with an error-status of noSuchName(2). GetNextRequests skip entries for nonexistent modules.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

switchPortStatsID 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.2
The port ID of the switch module port being referenced. Port 1 is always the internal 100Mbps port. Port 2 is always the internal 10Mbps port. Port 3 is always the external port. Note that port 2 is inactive on media modules and port 3 is inactive on internal switch modules. Note: Statistics for the external port are unavailable to the agent and are reported as 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3  

switchPortReadableFrames 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.3
The number of valid frames received by the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

switchPortReadableOctets 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.4
The number of octets (bytes) in all valid frames received by the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

switchPortFCSErrors 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.5
The number of valid-length frames received by the port that had FCS (frame check sequence) errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

switchPortAlignmentErrors 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.6
The number of valid-length frames received by the port that had alignment errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

switchPortFramesTooLong 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.7
The number of frames received by the port that were longer than 1518 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

switchPortShortEvents 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.8
The number of frames received by the port that were shorter than 82 bits.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

switchPortRunts 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.9
The number of frames received by the port that were longer than 82 bits but shorter than 512 bits (64 bytes).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

switchPortCollisions 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.10
The number of collisions detected on the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

switchPortLateEvents 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.11
The number of collisions detected on the port that occurred later than 512 bit-times into the transmission of a packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

switchPortVeryLongEvents 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.12
The number of times any activity continued for more than 4 to 7.5 milliseconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

switchPortDataRateMismatches 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.13
The number of times the incoming data rate mismatched the local clock source enough to cause a FIFO overflow or underflow.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

switchPortBroadcastPackets 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.14
The number of good broadcast frames received by the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

switchPortMulticastPackets 1.3.6.1.4.1.207.8.1.20.3.11.1.3.1.1.1.15
The number of good multicast (not broadcast) frames received by the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

fh800uSecurityInfo 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3
OBJECT IDENTIFIER    

securityPortTable 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3.3
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SecurityPortEntry

securityPortEntry 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3.3.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SecurityPortEntry  

securityPortGroupID 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3.3.1.1
ID of a hub unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

securityPortID 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3.3.1.2
Port ID in a hub unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

securityPortAddr 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3.3.1.3
MAC address
Status: mandatory Access: read-write
OBJECT-TYPE    
  PhysAddress  

securityAutoLearnAction 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3.3.1.5
Setting this object to inactive(1) disables the auto-learn function for the physical address authorized access to this port. Once this object is set to active(2), the agent will set the authorized address to 0 first and then start the auto-learn process, and the hub will begin to read the source address of the first incoming error-free frame. The source address obtained will become the authorized address and the object securityAuthorizedAddr will be changed accordingly. When the authorized address has been learned successfully, the status of this port will be reflected as learned(3). Otherwise the status will remain as active(2). Setting to the last value, learned(3), is not acceptable; 'snmpBadValue' will be returned.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inactive(1), active(2), learned(3)  

securityPortIntrusion 1.3.6.1.4.1.207.8.1.20.3.11.1.5.3.3.1.6
Set this variable to set function active or inactive
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inactive(1), warning-and-disable(2)  

fh800uIntrusionHappen 1
There were some intruders on some port in this system
TRAP-TYPE