FIBRONICS-MIB

File: FIBRONICS-MIB.mib (139383 bytes)

Imported modules

RFC1155-SMI

RFC-1212

RFC1213-MIB

Imported symbols

IpAddress	Counter	enterprises
TimeTicks	OBJECT-TYPE	DisplayString

Defined Types

ChGenAgEntry
SEQUENCE
	chGenAgId	INTEGER
	chGenAgType	INTEGER
	chGenAgMgmtIfType	INTEGER
	chGenAgAddr	OCTET STRING
	chGenAgSpecificOID	OBJECT IDENTIFIER

ChFbrAgEntry
SEQUENCE
	chFbrAgId	INTEGER
	chFbrAgSLIPAddress	IpAddress
	chFbrAgSWVersion	DisplayString
	chFbrAgKernelVersion	DisplayString
	chFbrAgCoprocSWVersion	DisplayString
	chFbrAgSWFault	DisplayString
	chFbrAgMgmtBusSelection	INTEGER
	chFbrAgCoprocCommStatus	INTEGER
	chFbrAgCommDebugMode	INTEGER
	chFbrAgConfigChangeTraps	INTEGER
	chFbrAgFaultTraps	INTEGER
	chFbrAgTrafficThreshTraps	INTEGER
	chFbrAgGroupEnrollDeenrollTraps	INTEGER
	chFbrAgSoftFaultTraps	INTEGER
	chFbrAgHubEnrollTraps	INTEGER
	chFbrAgTempThreshTraps	INTEGER
	chFbrAgSpecificOID	OBJECT IDENTIFIER
	chFbrAgLastAddrConfig	OCTET STRING
	chFbrAgSecAddrConfig	OCTET STRING
	chFbrAgSoftwareStatus	INTEGER
	chFbrAgConfigurationSymbol	DisplayString
	chFbrAgIntTemp	INTEGER
	chFbrAgBootVersion	DisplayString
	chFbrAgSensorFault	INTEGER
	chFbrAgSensorFaultTraps	INTEGER
	chFbrAgInterProcFault	INTEGER
	chFbrAgInterProcFaultTraps	INTEGER

ChFbrAgPermMngrEntry
SEQUENCE
	chFbrAgPermMngrId	INTEGER
	chFbrAgPermMngrAddr	IpAddress

ChFbrAgRmtNetEntry
SEQUENCE
	chFbrAgRmtNetId	INTEGER
	chFbrAgRmtNetAddr	IpAddress
	chFbrAgRmtNetMask	IpAddress

ChHWPSUEntry
SEQUENCE
	chHWPSUId	INTEGER
	chHWPSUActivityStatus	INTEGER
	chHWPSULocation	INTEGER
	chHWPSUVoltage	INTEGER

GenGroupEntry
SEQUENCE
	genGroupId	INTEGER
	genGroupSWVersion	DisplayString
	genGroupKernelVersion	DisplayString
	genGroupType	INTEGER
	genGroupDescr	DisplayString
	genGroupNumberOfPorts	INTEGER
	genGroupNumberOfIntPorts	INTEGER
	genGroupReset	INTEGER
	genGroupAutoMan	INTEGER
	genGroupFullConfig	OCTET STRING
	genGroupRedun12	INTEGER
	genGroupRedun34	INTEGER
	genGroupRedun13-14	INTEGER
	genGroupStandAloneMode	INTEGER
	genGroupInterProcCommStatus	INTEGER
	genGroupCommStatus	INTEGER
	genGroupHWStatus	INTEGER
	genGroupSupplyVoltageFault	INTEGER
	genGroupIntTemp	INTEGER
	genGroupSpecificOID	OBJECT IDENTIFIER
	genGroupConfigurationSymbol	DisplayString
	genGroupLastChange	TimeTicks

GenPortEntry
SEQUENCE
	genPortGroupId	INTEGER
	genPortId	INTEGER
	genPortFunctionality	INTEGER
	genPortType	INTEGER
	genPortDescr	DisplayString
	genPortActivityStatus	INTEGER
	genPortSecurityPolicy	OCTET STRING
	genPortSecureAddresses	OCTET STRING
	genPortIntPortConnection	INTEGER
	genPortAdminStatus	INTEGER
	genPortSpecificOID	OBJECT IDENTIFIER

GenIntPortEntry
SEQUENCE
	genIntPortGroupId	INTEGER
	genIntPortId	INTEGER
	genIntPortAdminStatus	INTEGER
	genIntPortActivityStatus	INTEGER
	genIntPortBusConnNumber	INTEGER
	genIntPortBusConnType	INTEGER
	genIntPortSpecificOID	OBJECT IDENTIFIER
	genIntPortMonitorMode	INTEGER

SoftRedundancyEntry
SEQUENCE
	softRedundancyId	INTEGER
	softRedundancyName	DisplayString
	softRedundancyGroupId1	INTEGER
	softRedundancyPortId1	INTEGER
	softRedundancyGroupId2	INTEGER
	softRedundancyPortId2	INTEGER
	softRedundancyStatus	INTEGER

EthAgEntry
SEQUENCE
	ethAgId	INTEGER
	ethAgPerfBusSelection	INTEGER

EthGroupEntry
SEQUENCE
	ethGroupId	INTEGER
	ethGroupFIFO	INTEGER
	ethGroup10BTPlus	INTEGER
	ethGroupIntPortsRedundancy	INTEGER
	ethGroupBackboneMode	INTEGER
	ethGroupFOIRLPlusMode	INTEGER
	ethGroupWrongPortSelection	INTEGER
	ethGroupBackupBus	INTEGER
	ethGroupSingleBusMode	INTEGER
	ethGroupSpecificOID	OBJECT IDENTIFIER
	ethGroup10FBPlus	INTEGER
	ethGroupMasterClock	INTEGER
	ethGroupIdleTrx	INTEGER
	ethGroupMJLPStatus	INTEGER

EthPortEntry
SEQUENCE
	ethPortGroupId	INTEGER
	ethPortId	INTEGER
	ethPortFunctionalStatus	INTEGER
	ethPortManPart	INTEGER
	ethPortJabber	INTEGER
	ethPortNoAUILoop	INTEGER
	ethPortMJLP	INTEGER
	ethPortFIFO	INTEGER
	ethPortAutoPartitionState	INTEGER
	ethPortSQETest	INTEGER
	ethPortLastSourceAddr	OCTET STRING
	ethPortUserStatus	INTEGER
	ethPortMainBusSelection	INTEGER
	ethPortTraffic	Counter
	ethPortFramesReceivedOK	Counter
	ethPortRunts	Counter
	ethPortPacketErrors	Counter
	ethPortSpecificOID	OBJECT IDENTIFIER
	ethPortCollisions	Counter
	ethPortPartitions	Counter
	ethPortPygmys	Counter

EthIntPortEntry
SEQUENCE
	ethIntPortGroupId	INTEGER
	ethIntPortId	INTEGER
	ethIntPortPartition	INTEGER
	ethIntPortJabber	INTEGER
	ethIntPortBackedUp	INTEGER

EthBusPerfEntry
SEQUENCE
	ethBusPerfAgId	INTEGER
	ethBusPerfId	INTEGER
	ethBusTrafficBuffer	OCTET STRING
	ethBusTrafficThresh	INTEGER
	ethBusPeakTraffic	INTEGER
	ethBusTotalCollisions	Counter
	ethBusTotalPackets	Counter
	ethBusTotalErrors	Counter
	ethBusTraffic	INTEGER
	ethBusUtilization	INTEGER
	ethBusPeakUtilization	INTEGER

EthBusClockEntry
SEQUENCE
	ethBusClockBusId	INTEGER
	ethBusClockId	INTEGER
	ethBusClockTestResult	INTEGER

TokRingEntry
SEQUENCE
	tokRingAgId	INTEGER
	tokRingId	INTEGER
	tokRingLeftSlot	INTEGER
	tokRingRightSlot	INTEGER
	tokRingTrafficBuffer	OCTET STRING
	tokRingTrafficThresh	INTEGER
	tokRingPeakTraffic	INTEGER
	tokRingNumberOfStations	INTEGER
	tokRingConfiguration	OCTET STRING
	tokRingBeaconing	INTEGER
	tokRingBeaconingStation	OCTET STRING
	tokRingStationsMatch	INTEGER
	tokRingTraffic	INTEGER
	tokRingSecurityMethod	INTEGER
	tokRingSecurityPolicy	OCTET STRING
	tokRingSecureAddr	OCTET STRING
	tokRingLastViolation	OCTET STRING
	tokRingUtilization	INTEGER
	tokRingPeakUtilization	INTEGER

TokGroupEntry
SEQUENCE
	tokGroupId	INTEGER
	tokGroupAutoRightLoop	INTEGER
	tokGroupAutoLeftLoop	INTEGER
	tokGroupManRightLoop	INTEGER
	tokGroupManLeftLoop	INTEGER
	tokGroupRightNeighbor	INTEGER
	tokGroupLeftNeighbor	INTEGER
	tokGroupIOMode	INTEGER
	tokGroupBridgeMode	INTEGER
	tokGroupManLinkLoop	INTEGER
	tokGroupManBusLoop	INTEGER
	tokGroupAutoLinkLoop	INTEGER
	tokGroupAutoBusLoop	INTEGER
	tokGroupSpecificOID	OBJECT IDENTIFIER

TokGroupRingEntry
SEQUENCE
	tokGroupRingGroupId	INTEGER
	tokGroupRingId	INTEGER
	tokGroupRingSpeed	INTEGER
	tokGroupRingInserted	INTEGER

TokPortEntry
SEQUENCE
	tokPortGroupId	INTEGER
	tokPortId	INTEGER
	tokPortBypass	INTEGER
	tokPortConnected	INTEGER
	tokPortTCP	INTEGER
	tokPortCableFault	INTEGER
	tokPortFunctionalStatus	INTEGER
	tokPortLastSourceAddr	OCTET STRING
	tokPortSpecificOID	OBJECT IDENTIFIER
	tokPortRingSpeedError	INTEGER

TsGroupEntry
SEQUENCE
	tsGroupId	INTEGER
	tsGroupLATStatus	INTEGER
	tsGroupOperationMode	INTEGER

LtalkPortEntry
SEQUENCE
	ltalkPortGroupId	INTEGER
	ltalkPortId	INTEGER
	ltalkPortTest	INTEGER
	ltalkPortTestResult	INTEGER
	ltalkPortJam	INTEGER

ClGroupEntry
SEQUENCE
	clGroupId	INTEGER
	clGroupClockRedundancy	INTEGER
	clGroupMainClock	INTEGER
	clGroupTestClocks	INTEGER

ClPortEntry
SEQUENCE
	clPortGroupId	INTEGER
	clPortId	INTEGER
	clPortFunctionalStatus	INTEGER

IwrGroupEntry
SEQUENCE
	iwrGroupId	INTEGER
	iwrOperState	INTEGER
	iwrPMState	INTEGER
	iwrIOMState	INTEGER

IwrWANEntry
SEQUENCE
	iwrWANGroupId	INTEGER
	iwrWANPortId	INTEGER
	iwrWANConnection	INTEGER
	iwrWANPortCableType	INTEGER

ItrGroupEntry
SEQUENCE
	itrGroupId	INTEGER
	itrMainSWVersion	DisplayString
	itrConfigState	INTEGER
	itrModuleState	INTEGER

ItrLinkEntry
SEQUENCE
	itrLinkGroupId	INTEGER
	itrLinkPortId	INTEGER
	itrLinkIf	INTEGER
	itrLinkMode	INTEGER
	itrLinkAsyncRate	INTEGER
	itrLinkSyncRate	INTEGER
	itrLinkParity	INTEGER
	itrLinkParityEvenOdd	INTEGER
	itrLinkStopBit	INTEGER
	itrLinkRemoteLANConn	INTEGER
	itrLinkFunctionalStatus	INTEGER

LseGroupEntry
SEQUENCE
	lseGroupId	INTEGER
	lseGroupFastOpen	INTEGER
	lseGroup10MSqlt	INTEGER
	lseGroupSmartSqlt	INTEGER
	lseGroupCParameter	INTEGER
	lseGroupIPGJamLength	INTEGER
	lseGroupJamLength	INTEGER
	lseGroupDataBlinderLength	INTEGER
	lseGroupIPGDataLength	INTEGER
	lseGroupActiveMonitor	INTEGER
	lseGroupBackBone	INTEGER
	lseGroupSetDefaults	INTEGER

LseIntPortEntry
SEQUENCE
	lseIntPortGroupId	INTEGER
	lseIntPortId	INTEGER
	lseIntPortIOMode	INTEGER
	lseIntPortResetSwitchCAM	INTEGER
	lseIntPortVideoPacket	INTEGER
	lseIntPortPriorityStateMachine	INTEGER
	lseIntPortActiveBroadcastPriority	INTEGER
	lseIntPortPriorityLevel	INTEGER
	lseIntPortSuperPriorityEnable	INTEGER
	lseIntPortRoutingMode	INTEGER
	lseIntPortGlobal	INTEGER
	lseIntPortLearnIOCAM	INTEGER
	lseIntPortSecurity	INTEGER
	lseIntPortIgnoreBusy	INTEGER
	lseIntPortRetryPriorityLevel1	INTEGER
	lseIntPortRetryPriorityLevel2	INTEGER
	lseIntPortRetryPriorityLevel3	INTEGER
	lseIntPortIgnoreProtocolType	INTEGER
	lseIntPortCompanyMAC	OCTET STRING
	lseIntPortTxSafetyZone	INTEGER
	lseIntPortRxSafetyZone	INTEGER
	lseIntPortTxBurstLength	INTEGER
	lseIntPortSecurityIntruder	INTEGER
	lseIntPortJabber	INTEGER
	lseIntPortCAM	OCTET STRING
	lseIntPortVideoStateMachine	INTEGER
	lseIntPortTransmitWeight	INTEGER

LsePortEntry
SEQUENCE
	lsePortGroupId	INTEGER
	lsePortId	INTEGER
	lsePortPolarity	INTEGER

Defined Values

fibronics		1.1.22
OBJECT IDENTIFIER

fbr101		1.1.22.101
OBJECT IDENTIFIER

fbr2		1.1.22.101.2
OBJECT IDENTIFIER

fbrStack		1.1.22.101.2.2
OBJECT IDENTIFIER

chassis		1.1.22.101.2.2.7
OBJECT IDENTIFIER

genGroup		1.1.22.101.2.2.8
OBJECT IDENTIFIER

genPort		1.1.22.101.2.2.9
OBJECT IDENTIFIER

genIntPort		1.1.22.101.2.2.10
OBJECT IDENTIFIER

softRedundancy		1.1.22.101.2.2.11
OBJECT IDENTIFIER

eth		1.1.22.101.2.2.12
OBJECT IDENTIFIER

tok		1.1.22.101.2.2.13
OBJECT IDENTIFIER

ts		1.1.22.101.2.2.14
OBJECT IDENTIFIER

ltalk		1.1.22.101.2.2.15
OBJECT IDENTIFIER

cl		1.1.22.101.2.2.16
OBJECT IDENTIFIER

fbrOID		1.1.22.101.2.2.17
OBJECT IDENTIFIER

fbrSecurity		1.1.22.101.2.2.18
OBJECT IDENTIFIER

fbrLanSwitch		1.1.22.101.2.2.19
OBJECT IDENTIFIER

deviceMgr		1.1.22.101.2.2.20
OBJECT IDENTIFIER

bRouter		1.1.22.101.2.2.21
OBJECT IDENTIFIER

probe		1.1.22.101.2.2.22
OBJECT IDENTIFIER

chHWType		1.1.22.101.2.2.7.1
Indicates type of enclosure in which the FIBRONICS SNMP agent operates.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	let18(1), let3(2), let36(3), let18Extended(4), lert40(5), let10(6), fdx100(7), stack(8), unknown(255)

chNumberOfSlots		1.1.22.101.2.2.7.2
Number of manageable slots in the chassis. In FIBRONICS implementation it describes the number of manageable slots in the chassis (not all slots should be occuppied).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

chNumberOfEthernetBuses		1.1.22.101.2.2.7.3
Indicates the number of internal Ethernet buses provided by the box.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

chNumberOfTRBuses		1.1.22.101.2.2.7.4
Indicates the number of internal Token Ring buses provided by the box.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

chNumberOfFDDIBuses		1.1.22.101.2.2.7.5
Indicates the number of internal FDDI buses provided by the box.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

chNumberOfLocalTalkBuses		1.1.22.101.2.2.7.6
Indicates the number of internal Local Talk buses provided by the box.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

chReset		1.1.22.101.2.2.7.7
Setting the value of this attribute to ON is interpreted as a reset command for the whole chassis. It initiates a complete reinitialisation of the chassis and of all the devices incorporated inside the chassis.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

chFullConfig		1.1.22.101.2.2.7.8
Full configuration message retrieved by FIBRONICS management stations at periodic interrogation times. Coded in compact internal FIBRONICS application format.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

chAg		1.1.22.101.2.2.7.9
OBJECT IDENTIFIER

chGenAgTable		1.1.22.101.2.2.7.9.1
Table of configuration attributes common to all SNMP agents in FIBRONICS hubs.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ChGenAgEntry

chGenAgEntry		1.1.22.101.2.2.7.9.1.1
An entry in the table, containing configuration attributes for a single agent.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ChGenAgEntry

chGenAgId		1.1.22.101.2.2.7.9.1.1.1
Agent index for identifying the agent.Takes the value of the slot number where the agent card is inserted. For box agents the value of chGenAgId is chNumberOfSlots+1.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

chGenAgType		1.1.22.101.2.2.7.9.1.1.2
Agent type.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	nma1-et(1), nma1-et-e(2), nma1-tr(3), nma2-et(4), nma2-tr(5), nma2-fddi(6), ielb(7), itlb(8), lts16(9), ierp(10), iefn(11), itfn(12), nm2069(13), nma-rt(14), unknown(255)

chGenAgMgmtIfType		1.1.22.101.2.2.7.9.1.1.3
This attribute describes one of the interfaces of agents existing on FIBRONICS modules and their type. Value 'none' defines the lack of an interface recognized by the management console. Any other value defines an interface whose type is recognized by the management console and may be used as a management channel.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), regular1822(2), hdh1822(3), ddn-x25(4), rfc877-x25(5), ethernet-csmacd(6), iso88023-csmacd(7), iso88024-tokenBus(8), iso88025-tokenRing(9), iso88026-man(10), starLan(11), proteon-10MBit(12), proteon-80MBit(13), hyperchannel(14), fddi(15), lapb(16), sdlc(17), t1-carrier(18), cept(19), basicIsdn(20), primaryIsdn(21), propPointToPointSerial(22), ppp(23), softwareLoopback(24), eon(25), ethernet-3Mbit(26), nsip(27), slip(28), ip(255)

chGenAgAddr		1.1.22.101.2.2.7.9.1.1.4
This attribute defines an unique address by which the agent may be addressed by the management console. The address format should be consistent with the type defined by chGenAgMgmtIfType.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..15)

chGenAgSpecificOID		1.1.22.101.2.2.7.9.1.1.5
This attribute provides the OID of another group containing additional more specific information regarding this instance.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

chFbrAgTable		1.1.22.101.2.2.7.9.2
Table of configuration attributes of FIBRONICS SNMP box agents in FIBRONICS hubs.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ChFbrAgEntry

chFbrAgEntry		1.1.22.101.2.2.7.9.2.1
An entry in the table, containing configuration attributes for a single agent.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ChFbrAgEntry

chFbrAgId		1.1.22.101.2.2.7.9.2.1.1
Agent index for identifying the agent. Identical to the index in chGenAgTable for the described agent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

chFbrAgSLIPAddress		1.1.22.101.2.2.7.9.2.1.2
IP address of the SLIP channel of the agent
Status: mandatory	Access: read-only
OBJECT-TYPE
	IpAddress

chFbrAgSWVersion		1.1.22.101.2.2.7.9.2.1.3
ASCII string for description and display of the agent software version.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

chFbrAgKernelVersion		1.1.22.101.2.2.7.9.2.1.4
ASCII string for description and display of the agent operating system (kernel) version.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

chFbrAgCoprocSWVersion		1.1.22.101.2.2.7.9.2.1.5
ASCII string describing the software version of the agent's coprocessor.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

chFbrAgSWFault		1.1.22.101.2.2.7.9.2.1.6
System fault emitted by agent software. It covers faults detected by the agent operating system and drivers. EnterpriseSpecific traps mechanism is used for transfering these traps to the management system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

chFbrAgMgmtBusSelection		1.1.22.101.2.2.7.9.2.1.7
Attribute describing the number of the bus on which management data are reported.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

chFbrAgCoprocCommStatus		1.1.22.101.2.2.7.9.2.1.8
Attribute describing the status of the communication between the agent and its coprocessor.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), commProblems(2), timeout(3)

chFbrAgCommDebugMode		1.1.22.101.2.2.7.9.2.1.9
Attribute describing the agent mode in which communication problem traps are sent to managers (value 'on') or are not sent to managers (value 'off').
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

chFbrAgConfigChangeTraps		1.1.22.101.2.2.7.9.2.1.10
The value of this attributes determines whether or not the agent sends Configuration Change traps to the manager.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

chFbrAgFaultTraps		1.1.22.101.2.2.7.9.2.1.11
The value of this attributes determines whether or not the agent sends Fault traps to the manager.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

chFbrAgTrafficThreshTraps		1.1.22.101.2.2.7.9.2.1.12
The value of this attributes determines whether or not the agent sends Traffic Threshold traps to the manager.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

chFbrAgGroupEnrollDeenrollTraps		1.1.22.101.2.2.7.9.2.1.13
The value of this attributes determines whether or not the agent sends Group Enrollment and Group Deenrollment traps to the manager.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

chFbrAgSoftFaultTraps		1.1.22.101.2.2.7.9.2.1.14
The value of this attributes determines whether or not the agent sends Software Fault traps to the manager.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

chFbrAgHubEnrollTraps		1.1.22.101.2.2.7.9.2.1.15
The value of this attributes determines whether or not the agent sends periodic Hub Enrollment traps to the manager.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

chFbrAgTempThreshTraps		1.1.22.101.2.2.7.9.2.1.16
The value of this attributes determines whether or not the agent sends Temperature Threshold traps to the manager.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

chFbrAgSpecificOID		1.1.22.101.2.2.7.9.2.1.17
This attribute provides the OID of another group containing additional more specific information regarding this instance.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

chFbrAgLastAddrConfig		1.1.22.101.2.2.7.9.2.1.18
Configuration attribute describing the last physical address detected at each port. Coded in internal FIBRONICS application format.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

chFbrAgSecAddrConfig		1.1.22.101.2.2.7.9.2.1.19
Configuration attribute describing the configuration of the secure addresses. Coded in internal FIBRONICS application format.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

chFbrAgSoftwareStatus		1.1.22.101.2.2.7.9.2.1.20
Describes configuration of the firmware on this agent. unLoadable(1) - is returned by agents which do not support the Software Download feature; loaded(2) - is returned by agents with loaded software; downLoading(3) - when the attribute is set to this value by manager, it triggers the Software Download procedure. When procedure finished, agent software will restablish value loaded(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	unLoadable(1), loaded(2), downLoading(3)

chFbrAgConfigurationSymbol		1.1.22.101.2.2.7.9.2.1.21
Defines the Configuration Symbol attached to any hardware module manufactured by FIBRONICS. One single character A..Z defines the CS version. For older modules which did not support this option on SNMP character '*' will be returned.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1)

chFbrAgIntTemp		1.1.22.101.2.2.7.9.2.1.22
Internal temperature measured by the temperature sensor placed on the agent card. Expressed in Celsius degrees.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

chFbrAgBootVersion		1.1.22.101.2.2.7.9.2.1.23
ASCII string for description and display of the agent boot software version.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

chFbrAgSensorFault		1.1.22.101.2.2.7.9.2.1.24
A code of a sensor fault discovered by the agent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

chFbrAgSensorFaultTraps		1.1.22.101.2.2.7.9.2.1.25
This attribute enables/disables generation of the sensor fault trap.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

chFbrAgInterProcFault		1.1.22.101.2.2.7.9.2.1.26
A code of intercommunication fault between Main - Master processors.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

chFbrAgInterProcFaultTraps		1.1.22.101.2.2.7.9.2.1.27
This attribute enables/disables generation of the intercommunication fault trap.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

chFbrAgSetup		1.1.22.101.2.2.7.9.3
OBJECT IDENTIFIER

chFbrAgMaxNmbOfMngrs		1.1.22.101.2.2.7.9.3.1
Maximum number of permanent managers.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

chFbrAgPermMngrTable		1.1.22.101.2.2.7.9.3.2
Table of permanent managers.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ChFbrAgPermMngrEntry

chFbrAgPermMngrEntry		1.1.22.101.2.2.7.9.3.2.1
An entry in the permanent managers table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ChFbrAgPermMngrEntry

chFbrAgPermMngrId		1.1.22.101.2.2.7.9.3.2.1.1
Index in the permanent managers table. It ranges from 1 to chFbrAgMaxNmbOfMngrs
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

chFbrAgPermMngrAddr		1.1.22.101.2.2.7.9.3.2.1.2
IP address of a permanent manager.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

chFbrAgMaxNmbOfNets		1.1.22.101.2.2.7.9.3.3
Maximum number of remote networks.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

chFbrAgRmtNetTable		1.1.22.101.2.2.7.9.3.4
Remote networks table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ChFbrAgRmtNetEntry

chFbrAgRmtNetEntry		1.1.22.101.2.2.7.9.3.4.1
Entry in the remote networks table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ChFbrAgRmtNetEntry

chFbrAgRmtNetId		1.1.22.101.2.2.7.9.3.4.1.1
Index of a remote network. It ranges from 1 to chFbrAgMaxNmbOfNets.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

chFbrAgRmtNetAddr		1.1.22.101.2.2.7.9.3.4.1.2
Address of a remote network. The host portion is always 0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

chFbrAgRmtNetMask		1.1.22.101.2.2.7.9.3.4.1.3
Subnet mask for the remote network.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

chFbrAgDateTime		1.1.22.101.2.2.7.9.3.5
Current date and time for NMA-TR. The format is YYMMDDhhmmssw, where w - day of the week e.g., 1=Mon, 2=Tue,..., 7=Sun.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(13)

chFbrAgReset		1.1.22.101.2.2.7.9.3.6
This attribute enables the user to reset the agent.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

chMgr		1.1.22.101.2.2.7.10
OBJECT IDENTIFIER

chMgrTrapRepStatus		1.1.22.101.2.2.7.10.1
Value 'on' indicates that SNMP agent should send SNMP traps (traffic ex- cluded) to the manager.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

chMgrContPerfRep		1.1.22.101.2.2.7.10.2
Value 'on' indicates that the SNMP agent should send traffic SNMP traps to the manager.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

chMgrMngmtState		1.1.22.101.2.2.7.10.3
Attribute to be set by manager in order to instruct the agent to enter into a management session with the console. Setting this value to 'on' has the effect of performing an 'I am your manager' action upon the agent.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

chMgrPollInterval		1.1.22.101.2.2.7.10.4
The attribute defines an interval during which the agent is waiting for the manager's requests. Default value 5 minutes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

chHW		1.1.22.101.2.2.7.11
OBJECT IDENTIFIER

chHWPSUTable		1.1.22.101.2.2.7.11.1
Table of configuration attributes for Power Supply Units. This table can be retrieved only from agents equipped with adequate hardware.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ChHWPSUEntry

chHWPSUEntry		1.1.22.101.2.2.7.11.1.1
An entry in the table, containing configuration attributes for a single Power Supply Unit.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ChHWPSUEntry

chHWPSUId		1.1.22.101.2.2.7.11.1.1.1
PSU index for identifying the PSU.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

chHWPSUActivityStatus		1.1.22.101.2.2.7.11.1.1.2
This attribute defines the status of the PSU in what concerns supplying power to the chassis. NotActive - indicates a disabled or defective PSU which cannot supply power to the chassis. Dormant - indicates a functional PSU which is installed for backup purposes and can at any moment supply power to the devices in the chassis. Active - indicates that the PSU supplies power to the chassis.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notActive(1), dormant(2), active(3)

chHWPSULocation		1.1.22.101.2.2.7.11.1.1.3
Describes the location (internal or external) of the PSU.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), internal(2), external(3)

chHWPSUVoltage		1.1.22.101.2.2.7.11.1.1.4
Indicates voltage of PSU expressed in miliVolts.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

chHWIntTempWarning		1.1.22.101.2.2.7.11.2
Fault condition indicating that the temperature measured by one of the sensors internal to the box exceeded chHWIntTempThresh.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), exceeded(2)

chHWIntTempThresh		1.1.22.101.2.2.7.11.3
Internal enclosure temperature threshold value, expressed in degrees Celsius. When exceeded, a trap is sent to the management console.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

chHWPeakIntTemp		1.1.22.101.2.2.7.11.4
Maximum internal temperature inside the chassis. It is the maximum of the temperature values detected by different temperature sensors inside the box.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

chSlotLastChange		1.1.22.101.2.2.7.12
This attribute contains the value of sysUpTime at the time any of the modules in the hub was enrolled/deenrolled.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

genGroupTable		1.1.22.101.2.2.8.1
Table of configuration attributes for managed FIBRONICS modules. Includes configuration data which are independent of the specific functionality of the module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		GenGroupEntry

genGroupEntry		1.1.22.101.2.2.8.1.1
An entry in the table, containing data about a single group.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	GenGroupEntry

genGroupId		1.1.22.101.2.2.8.1.1.1
Index which identifies the group inside the chassis for which this entry contains information. Equals the number of the slot by which the group is accessed. This value is never greater than chNumberOfSlots.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

genGroupSWVersion		1.1.22.101.2.2.8.1.1.2
ASCII string for description and display of the group software version.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

genGroupKernelVersion		1.1.22.101.2.2.8.1.1.3
ASCII string for description and display of the group kernel version.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

genGroupType		1.1.22.101.2.2.8.1.1.4
Attribute describing the type of FIBRONICS Ethernet group.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	le10b(1), le10b-2(2), le10c(3), le10c-2(4), le15(5), le15-2(6), le20(7), le30x(8), le30x-2(9), le30xd(10), le40x(11), le40xt(12), ltr4-RJ45(13), ltr4-D9(14), ltr4-D25(15), ltr4-FO(16), ltrio-RJ45(19), ltrio-D9(20), ltrio-D25(21), ltrio-FO(22), ltrio-Con1(23), ltrio-Con2(24), le10b-2r(25), le10c-2r(26), le80xt(27), le140xt(28), ielb(29), ltrf4(30), ltrf16(31), lts16(32), le20n(33), ltr104-RJ45(34), le20r(35), llt8(36), le20s(37), le10b2n(38), ltr104-D9(39), ltr104-D25(40), ltrt-RJ45(41), ltrt-D9(42), ltr104f(43), itlb(44), le140xtf(45), le120r(46), le120r-2(47), le140xtc(48), le110b(49), le110bq(50), lcl100(51), le140xtq(52), le20n-fb(53), le20s-fb(54), le140xtf-fb(55), ltr104s(56), lert40-AUI(57), lert40-10BASET(58), lfd104-mic(59), lfd104-stm(60), lfd104-stl(61), lfd104-stp(62), lfd104-utp(63), lfd102-mic(64), lfd102-stm(65), lfd102-sts(66), le140xtn(67), ltr104a(68), le120q(69), le120sq2(70), le120sq5(71), le120q-fb(72), le120sq2-fb(73), le120sq5-fb(74), ltr108t(75), ltr108f(76), lse808(77), lhs(78), ierb(79), iefn(80), itfn(81), itre1(82), istc1(83), iftc(84), ietlb(85), ierp(86), lse108(87), lse208(88), le110cq(89), itre2(90), istc2(91), fer2061(92), le115q(93), sh-t16(94), sh-e8(95), lhb(96), sh-efn(97), sh-tfn(98), itng(99), lace100(100), le140xts(101), le40xtn(102), le80xtn(103), unknown(255)

genGroupDescr		1.1.22.101.2.2.8.1.1.5
Descriptor of the group in ASCII (readable) format, mainly for use with generic management applications.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

genGroupNumberOfPorts		1.1.22.101.2.2.8.1.1.6
Number of ports in group. It is assumed that on each group the ports are assigned unique numbers in the range from 1 to genGroupNumberOfPorts. They correspond to the number of ports on the module (FRU)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

genGroupNumberOfIntPorts		1.1.22.101.2.2.8.1.1.7
Number of internal ports (ports connected to the chassis buses) on the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

genGroupReset		1.1.22.101.2.2.8.1.1.8
Setting the value of this attribute to 'on' is interpreted as a software RESET command. Sensor software is reinitialized and according to the sensor specifications, partial or total reset of the module hardware may be performed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

genGroupAutoMan		1.1.22.101.2.2.8.1.1.9
This attribute reflects the status of the Auto/Manual switch which defines the working mode of FIBRONICS sensors. In the MANUAL mode no set operations may be performed on attributes related to the sensor. The sensor works according to configuration switches set by hardware and transmits all configuration information to the agent. In the AUTO mode, hardware switches are overridden by set commands.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	auto(1), man(2)

genGroupFullConfig		1.1.22.101.2.2.8.1.1.10
Attribute describing the full configuration of a group in internal FIBRONICS application format.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

genGroupRedun12		1.1.22.101.2.2.8.1.1.11
Value ON of this attribute defines a redundancy (backup) relationship between synchronous external ports 1 and 2 on a FIBRONICS module.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

genGroupRedun34		1.1.22.101.2.2.8.1.1.12
Value ON of this attribute defines a redundancy (backup) relationship between synchronous external ports 3 and 4 on a FIBRONICS module.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

genGroupRedun13-14		1.1.22.101.2.2.8.1.1.13
Value ON of this attribute defines a redundancy (backup) relationship between synchronous external ports 13 and 14 on a FIBRONICS module.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

genGroupStandAloneMode		1.1.22.101.2.2.8.1.1.14
Value ON of this attribute indicates the sensor's operation Stand Alone mode . Internal ports are disabled and the card functions in a local star configuration toward its external ports.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

genGroupInterProcCommStatus		1.1.22.101.2.2.8.1.1.15
This attribute describes the status of the communication between the microprocessor of the sensor and the microprocessor of the agent on cards with embedded agents.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), commProblems(2), noCommunication(3), notSupported(255)

genGroupCommStatus		1.1.22.101.2.2.8.1.1.16
This attribute describes the communication status of the group with the SNMP Agent as detected and reported by the agent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), commProblems(2), noCommunication(3), notSupported(255)

genGroupHWStatus		1.1.22.101.2.2.8.1.1.17
This attribute describes the status of the group hardware as detected by the sensors software.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), hardwareProblems(2), notSupported(255)

genGroupSupplyVoltageFault		1.1.22.101.2.2.8.1.1.18
A value 'on' of this attribute informs of a 'voltage supply out-of-range' error condition on sensor equipped with hardware which checks this condition.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

genGroupIntTemp		1.1.22.101.2.2.8.1.1.19
Internal temperature of the enclosure as measured by the specific module instance.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

genGroupSpecificOID		1.1.22.101.2.2.8.1.1.20
This attribute provides the OID of another group containing additional more specific information regarding this instance.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

genGroupConfigurationSymbol		1.1.22.101.2.2.8.1.1.21
Defines the Configuration Symbol attached to any hardware module manufactured by FIBRONICS. One single character A..Z defines the CS version. For older modules which did not support this option on SNMP character '*' will be returned.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1)

genGroupLastChange		1.1.22.101.2.2.8.1.1.22
This attribute contains the value of sysUpTime at the time any change pertaining to the specified group occurred.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

genPortTable		1.1.22.101.2.2.9.1
Table of configuration attributes for managed FIBRONICS ports. Includes configuration data which are independent of the specific functionality of the port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		GenPortEntry

genPortEntry		1.1.22.101.2.2.9.1.1
An entry in the table, containing data about a single port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	GenPortEntry

genPortGroupId		1.1.22.101.2.2.9.1.1.1
Index which identifies the group inside the chassis for which this entry contains information. Equals the number of the slot by which the group containing the port is accessed. This value is never greater than chNumberOfSlots.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

genPortId		1.1.22.101.2.2.9.1.1.2
Index which identifies the port inside the group for which this entry contains information. It generally corresponds with the number by which the port is identified and is marked on the module. This value is never greater than genGroupNumberOfPorts of the group to which the port belongs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

genPortFunctionality		1.1.22.101.2.2.9.1.1.3
Describes the functionality of the port according to international standards.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	private(1), repeaterAUI(2), repeaterThin(3), repeater10BaseT(4), tenBaseFSyncAct(5), foirl(6), xcvr(7), lobe(8), ri(9), ro(10), serial(11), localTalk(12), fddi(13), clock(14), genTokenRing(15), dte(16), activeLobe(17), genActiveTokenRing(18), tenBaseFB(19), lse10BaseT(20), lhsFiber(21), wan(22), star(23), activeRI(24), activeRO(25)

genPortType		1.1.22.101.2.2.9.1.1.4
Attribute describing the type of FIBRONICS port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	le10bPort(1), le10cPort(2), le15Port(3), le20Port(4), le30xPort(5), le30xdPort(6), le40xPort(7), le40xtPort(8), lobeRJ45(9), lobeD9(10), lobeD25(11), lobeFO(12), ri104D25(13), ro104D25(14), riRJ45(15), riD9(16), riD25(17), riFO(18), ri104RJ45(19), ri104D9(20), roRJ45(21), roD9(22), roD25(23), roFO(24), ro104RJ45(25), ro104D9(26), le80xtPort(27), le140xtPort(28), ielb-AUIPort(29), ielb-10btPort(30), ltrf4Port(31), ltrf16Port(32), lts16Port(33), llt8Port(34), le20rPort(35), itlbRoPort(36), itlbRiPort(37), itlbDTEPort(38), starFO(39), le10bnPort(40), le120rPort(41), le140xtf-foPort(42), le140xtf-10btPort(43), le140xtcPort(44), le110bPort(45), le110bqPort(46), le140xtqPort(47), lert40-AUIPort(48), lert40-10btPort(49), clock-int(50), clock-ext(51), ri104RJ45S(52), r0104RJ45S(53), lobe104RJ45S(54), le20fbPort(55), le140xtf-fofbPort(56), fddi-micPort1(57), fddi-micPort2(58), fddi-micPort3(59), fddi-stmPort1(60), fddi-stmPort2(61), fddi-stmPort3(62), fddi-stlPort1(63), fddi-stlPort2(64), fddi-stlPort3(65), fddi-stpPort1(66), fddi-stpPort2(67), fddi-stpPort3(68), fddi-utpPort1(69), fddi-utpPort2(70), fddi-utpPort3(71), fddi-stsPort1(72), fddi-stsPort2(73), fddi-stsPort3(74), le140xtnPort(75), ltr104a-lobePort(76), ltr104a-riPort(77), ltr104a-roPort(78), le120qPort(79), le120sq2PortS(80), le120sq2PortM(81), le120sq5Port(82), le120q-fbPort(83), le120sq2-fbPortS(84), le120sq2-fbPortM(85), le120sq5-fbPort(86), ltr108t-lobePort1(87), ltr108t-riPort1(88), ltr108t-roPort1(89), ltr108t-lobePort(90), ltr108f-lobePort(91), ltr108f-starPortFO(92), ltr108f-riPortFO(93), ltr108f-roPortFO(94), lse808Port(95), lhsPort(96), ierbPort(97), iefnPort(98), itfnPort(99), itrePort(100), istcPort(101), iftcPort(102), ietlb-lobePort(103), ietlb-riPort(104), ietlb-roPort(105), ietlb-10BaseTPort(106), ierpPort(107), lse108Port(108), lse208Port(109), le110cqPort(110), ltr108t-starPort1(111), fer2061-10btPort(112), fer2061-AUIPort(113), fer2061-FOPort(114), fer2061-FOSyncPort(115), le115qPort(116), sht-lobePort(117), sht-riRJ45Port(118), sht-riD9Port(119), sht-riFOPort(120), sht-roRJ45Port(121), sht-roD9Port(122), sht-roFOPort(123), lhbPort(124), itngPort(125), le140xtsPort(126), le40xtnPort(127), le80xtnPort(128), unknownPort(255)

genPortDescr		1.1.22.101.2.2.9.1.1.5
Descriptor of the port in ASCII (readable) format, mainly for use with generic management applications.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

genPortActivityStatus		1.1.22.101.2.2.9.1.1.6
This attribute defines the status of ports that may be part of a redundancy scheme. NotActive - indicates a disabled port which cannot transmit or receive packets even if included in a redundancy scheme. Dormant - indicates an enabled port which does not transmit or receive packets, but because it is included in a redundancy scheme, it may at any moment become responsible packet transmission and reception. Active - indicates that the port transmits and receives packets, serving as the main path in the redundant configuration.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notActive(1), dormant(2), active(3), notSupported(255)

genPortSecurityPolicy		1.1.22.101.2.2.9.1.1.7
Security policy (Trap Only or Trap and Close) assigned to this port. The information is coded in internal FIBRONICS format.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

genPortSecureAddresses		1.1.22.101.2.2.9.1.1.8
This attribute defines the security information (physical addresses) relevant for the entry. Coded in internal format, cryptographic methods may be used for privacy purposes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

genPortIntPortConnection		1.1.22.101.2.2.9.1.1.9
The value of this attribute defines the internal port to which the port is connected. A value 0 of this attribute would indicate no internal port connection (stand-alone mode). Any other positive value equals the number of the internal port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

genPortAdminStatus		1.1.22.101.2.2.9.1.1.10
A disabled port neither transmits nor receives. The port must be explici- tenly enabled to restore operation. For token ring ports, this attribute is read-only.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

genPortSpecificOID		1.1.22.101.2.2.9.1.1.11
This attribute provides the OID of another group containing additional more specific information regarding this instance.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

genIntPortTable		1.1.22.101.2.2.10.1
Table of configuration attributes of FIBRONICS internal ports. Internal ports are physical and/or logical entities which transfer information and connect FIBRONICS modules to the internal networks (buses).
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		GenIntPortEntry

genIntPortEntry		1.1.22.101.2.2.10.1.1
An entry in the table, containing data about a single port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	GenIntPortEntry

genIntPortGroupId		1.1.22.101.2.2.10.1.1.1
Index which identifies the group inside the chassis for which this entry contains information. Equals the number of the slot by which the group containing the internal port is accessed. This value is never greater than chNumberOfSlots.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

genIntPortId		1.1.22.101.2.2.10.1.1.2
Index which identifies the port inside the group for which this entry contains information. This value is never greater than genGroupNumberOfIntPorts of the group to which the port belongs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

genIntPortAdminStatus		1.1.22.101.2.2.10.1.1.3
Defines the capability of the internal port to transmit or receive data. A disabled internal port neither transmits or receives. The port must be explicitly enabled to restore operation.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

genIntPortActivityStatus		1.1.22.101.2.2.10.1.1.4
This attribute defines the status of internal ports that may be part of a redundancy scheme. NotActive - indicates a disabled port which cannot transmit or receive packets even if included in a redundancy scheme. Dormant - indicates an enabled port which does not transmit or receive packets, but because it is included in a redundancy scheme, it may at any moment become responsible for packet transmission and reception. Active - indicates that the port transmits and receives packets, serving as the main path in the redundant configuration.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notActive(1), dormant(2), active(3), notSupported(255)

genIntPortBusConnNumber		1.1.22.101.2.2.10.1.1.5
The value of this attribute defines the bus to which the internal port is connected. The value '0' indicates that the port is disconnected from the bus.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

genIntPortBusConnType		1.1.22.101.2.2.10.1.1.6
The value of this attribute defines the type of the bus to which the internal port is connected.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ethernet(1), token-ring(2), local-talk(3), fddi(4), high-speed(5), other(255)

genIntPortSpecificOID		1.1.22.101.2.2.10.1.1.7
This attribute provides the OID of another group containing additional more specific information regarding this instance.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

genIntPortMonitorMode		1.1.22.101.2.2.10.1.1.8
This attribute enables to monitor a specified bus (RMON).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

softRedundancyTable		1.1.22.101.2.2.11.1
Table of attributes which define software redundancy links defined by means of the FIBRONICS chassis SNMP agents.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SoftRedundancyEntry

softRedundancyEntry		1.1.22.101.2.2.11.1.1
An entry in the table, containing data about a single software redundancy link.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SoftRedundancyEntry

softRedundancyId		1.1.22.101.2.2.11.1.1.1
Index which identifies the software redundancy link which for which the current entry provides information.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

softRedundancyName		1.1.22.101.2.2.11.1.1.2
Logical name of the software redundancy link
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(15)

softRedundancyGroupId1		1.1.22.101.2.2.11.1.1.3
ID of the group to which the main port on the software redundancy link belongs. This value is never greater than chNumberOfSlots.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

softRedundancyPortId1		1.1.22.101.2.2.11.1.1.4
ID of the main port on the software redundancy link.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

softRedundancyGroupId2		1.1.22.101.2.2.11.1.1.5
ID of the group to which the secondary port on the software redundancy link belongs. This value is never greater than chNumberOfSlots.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

softRedundancyPortId2		1.1.22.101.2.2.11.1.1.6
ID of the secondary port on the software redundancy link.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

softRedundancyStatus		1.1.22.101.2.2.11.1.1.7
Status of the entry in the softRedundancy Table: valid(1) indicates that row is busy with meaningful values; createRequest(2) will be set by manager when creating a new row; underCreation(3) indicates that agent accepts create command and performs it; invalid(4) indicates that no meaningful values are present in the row. Managers set this value in order to transmit a 'Delete row' command to agent.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	valid(1), createRequest(2), underCreation(3), invalid(4)

ethAg		1.1.22.101.2.2.12.1
OBJECT IDENTIFIER

ethAgTable		1.1.22.101.2.2.12.1.1
Table of attributes which define configuration characteristics for FIBRONICS chassis SNMP agents which use Ethernet as in-band management protocol.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthAgEntry

ethAgEntry		1.1.22.101.2.2.12.1.1.1
An entry in the table, containing data about a single Ethernet agent.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	EthAgEntry

ethAgId		1.1.22.101.2.2.12.1.1.1.1
Index which identifies the Ethernet agent for which the current entry provides information.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

ethAgPerfBusSelection		1.1.22.101.2.2.12.1.1.1.2
Attribute describing the bus attached to the performance data collection hardware on those FIBRONICS agent hardware implementations which support configuration management on multi-Ethernet bus enclosures, but performan- ce data collection on a single bus.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

ethGroup		1.1.22.101.2.2.12.2
OBJECT IDENTIFIER

ethGroupTable		1.1.22.101.2.2.12.2.1
Table of attributes which define configuration characteristics for FIBRONICS Ethernet modules.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthGroupEntry

ethGroupEntry		1.1.22.101.2.2.12.2.1.1
An entry in the table, containing data about a single Ethernet module (group).
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	EthGroupEntry

ethGroupId		1.1.22.101.2.2.12.2.1.1.1
Index which identifies the group inside the chassis for which this entry contains information. Equals the number of the slot by which the group is accessed. This value is never greater than chNumberOfSlots.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

ethGroupFIFO		1.1.22.101.2.2.12.2.1.1.2
Value ON of this attribute describes an internal FIFO error sensed by the internal hardware mechanism of a FIBRONICS repeater.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethGroup10BTPlus		1.1.22.101.2.2.12.2.1.1.3
Value ON of this attribute defines activation of the 10BaseTPlus mode - a FIBRONICS extension of the 10BaseT standard.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethGroupIntPortsRedundancy		1.1.22.101.2.2.12.2.1.1.4
Value ON of this attribute defines a redundancy (backup) relationship between internal ports 1 and 2 on a FIBRONICS module.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethGroupBackboneMode		1.1.22.101.2.2.12.2.1.1.5
Value On of this attribute defines Backbone Mode of a sensor. Internal ports are enabled and the information path goes straightly from external port to internal bus, via corresponding internal port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethGroupFOIRLPlusMode		1.1.22.101.2.2.12.2.1.1.6
Value On of this attribute defines FOIRL of a sensor. When this attribute has value ON, FOIRL Plus mode is enabled, while value OFF indicates stan- dard FOIRL mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethGroupWrongPortSelection		1.1.22.101.2.2.12.2.1.1.7
A value ON of this attribute warns of incorrect selection of enabled ports on sensors which impose restrictions on this configura- tion (e.g. integrated local bridges.)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethGroupBackupBus		1.1.22.101.2.2.12.2.1.1.8
Defines the common secondary bus for Ethernet groups with bus redundancy defined at port level.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..4

ethGroupSingleBusMode		1.1.22.101.2.2.12.2.1.1.9
Value 'on of this attribute defines bus-star mode for cards supporting this type of configuration.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethGroupSpecificOID		1.1.22.101.2.2.12.2.1.1.10
This attribute provides the OID of another group containing additional more specific information regarding this instance.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

ethGroup10FBPlus		1.1.22.101.2.2.12.2.1.1.11
This variable enables/disables 10BaseFB plus mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethGroupMasterClock		1.1.22.101.2.2.12.2.1.1.12
This attribute pertains to the SH-E16 chassis and defines the hub in the stack that generates the clock.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethGroupIdleTrx		1.1.22.101.2.2.12.2.1.1.13
This attribute is relevant to the LE-120Q/SQ modules and when set to 'off' after port disable terminates also light propagation (for redundancy tests).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethGroupMJLPStatus		1.1.22.101.2.2.12.2.1.1.14
This attribute defines the MJLP error status on the group level.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethPort		1.1.22.101.2.2.12.3
OBJECT IDENTIFIER

ethPortTable		1.1.22.101.2.2.12.3.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthPortEntry

ethPortEntry		1.1.22.101.2.2.12.3.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	EthPortEntry

ethPortGroupId		1.1.22.101.2.2.12.3.1.1.1
Id of the group to which the port belongs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ethPortId		1.1.22.101.2.2.12.3.1.1.2
Unique Id of the port in the ethPortTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ethPortFunctionalStatus		1.1.22.101.2.2.12.3.1.1.3
The value of this attribute reflects the functional status of FIBRONICS synchronous ports. Note that it is not mandatory that all ports support all the enumerated states. Here is the minimal set possible states: OK - fully functional port, transmitting and receiving packets. RLD - receive link down condition on the port. TLD - transmit link down condition on the port. LocalJabber - fault condition indicating that the port emitted jabber. RemoteJabber - fault condition indicating that remote jabber was sensed at the port. IllSeq - Fault condition indicating an illegal synchronization sequence at the port. ShortCircuit - short-circuit fault condition detected at the port. PartitionOrLocalJabber - RemoteFaultOrLockLoss -
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), rld(2), localJabber(3), tld(4), remoteJabber(5), illSeq(6), shortCirc(7), partitionOrLocalJabber(8), remoteFaultOrLockLost(9), remoteFault(10), lockLost(11), notSupported(255)

ethPortManPart		1.1.22.101.2.2.12.3.1.1.4
Setting the value of this attribute to ON activates the manual partition mechanism at the port level. Setting the value of this attribute to OFF cancels the partition mechanism. The segment may reconnect after the reception of 32 packets. Attribute vaild for repeater modules from the LE-10 family.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethPortJabber		1.1.22.101.2.2.12.3.1.1.5
Value ON of this attribute reflects jabber transmitted to the port by the hardware of a FIBRONICS repeater or transceiver, as a result of collisions detected on the port. Valid for all modules in the LE-10 and LE-15 families.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethPortNoAUILoop		1.1.22.101.2.2.12.3.1.1.6
Value ON of this attribute indicates that a No AUI Loop fault condition was detected on an AUI repeater port. Valid for LE-10C family of modu- les.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethPortMJLP		1.1.22.101.2.2.12.3.1.1.7
Value ON of this attribute describes an internal MJLP (MAU Jabber Lockup Protection) error sensed by the internal hardware mechanism of a FIBRONICS repeater. Valid for LE140XTF.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethPortFIFO		1.1.22.101.2.2.12.3.1.1.8
Value ON of this attribute describes an internal FIFO error sensed by the internal hardware mechanism of a FIBRONICS repeater. Valid for LE140XTF.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethPortAutoPartitionState		1.1.22.101.2.2.12.3.1.1.9
The AutoPart condition indicates that the port is currently partitioned by the auto-partition protection mechanism.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	autoPartition(1), notAutoPartition(2), notSupported(255)

ethPortSQETest		1.1.22.101.2.2.12.3.1.1.10
Settable attribute which allows activation of SQE test for FIBRONICS integrated transceivers.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2), notSupported(255)

ethPortLastSourceAddr		1.1.22.101.2.2.12.3.1.1.11
Ethernet source address of the last readable frame received by this port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

ethPortUserStatus		1.1.22.101.2.2.12.3.1.1.12
Attribute defining the connection of a port to a single Ethernet source or to a multi-source (segment or star).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	singleUser(1), multiUser(2), notSupported(255)

ethPortMainBusSelection		1.1.22.101.2.2.12.3.1.1.13
On cards with port-level redundancy, defines the main bus for each port instance as selected by user.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

ethPortTraffic		1.1.22.101.2.2.12.3.1.1.14
Counter for the number of bits received on this port in frames with legal length information.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

ethPortFramesReceivedOK		1.1.22.101.2.2.12.3.1.1.15
A representation of the total number of frames of legal length that have not been corrupted in transmission. These frames can be encoded and decoded by the commonly available MACs and provide a measure of the network bandwidth being used. The number does not include frames received with frame-too-long, FCS, alignment errors, frames lost due to internal MAC sublayer errors, runts or pygmys.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

ethPortRunts		1.1.22.101.2.2.12.3.1.1.16
Counter for the number of collision fragments longer than a pygmy and shorter than a legal packet, detected on this port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

ethPortPacketErrors		1.1.22.101.2.2.12.3.1.1.17
Counter for the number of frames with errors detected on the port by the FIBRONICS agent hardware. This generic port error comprises too long packets, CRC and alignment errors.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

ethPortSpecificOID		1.1.22.101.2.2.12.3.1.1.18
This attribute provides the OID of another group containing additional more specific information regarding this instance.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

ethPortCollisions		1.1.22.101.2.2.12.3.1.1.19
The number of collisions observed on a specified port. Relevant for MPR modules.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

ethPortPartitions		1.1.22.101.2.2.12.3.1.1.20
The number of partitions observed on a specified port. Relevant for MPR modules.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

ethPortPygmys		1.1.22.101.2.2.12.3.1.1.21
The number of pygmys observed on a specified port. Relevant for MPR modules.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

ethIntPort		1.1.22.101.2.2.12.4
OBJECT IDENTIFIER

ethIntPortTable		1.1.22.101.2.2.12.4.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthIntPortEntry

ethIntPortEntry		1.1.22.101.2.2.12.4.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	EthIntPortEntry

ethIntPortGroupId		1.1.22.101.2.2.12.4.1.1.1
ID of the group to which the internal port belongs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

ethIntPortId		1.1.22.101.2.2.12.4.1.1.2
ID of the internal port in the ethIntPortTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

ethIntPortPartition		1.1.22.101.2.2.12.4.1.1.3
This condition indicates that the internal port is currently partitioned from the bus by the auto-partition protection mechanism.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethIntPortJabber		1.1.22.101.2.2.12.4.1.1.4
Value ON of this attribute reflects jabber being transmitted to the bus by the hardware of a FIBRONICS repeater, as a result of collisions detected on the internal bus of the enclosure. This situation is similar to MJLP as defined by the Repeater Management standard.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethIntPortBackedUp		1.1.22.101.2.2.12.4.1.1.5
Indicates that internal port is part of a redundancy scheme.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

ethBus		1.1.22.101.2.2.12.5
OBJECT IDENTIFIER

ethBusPerfTable		1.1.22.101.2.2.12.5.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthBusPerfEntry

ethBusPerfEntry		1.1.22.101.2.2.12.5.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	EthBusPerfEntry

ethBusPerfAgId		1.1.22.101.2.2.12.5.1.1.1
ID of the agent in the ethBusPerfTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

ethBusPerfId		1.1.22.101.2.2.12.5.1.1.2
ID of the bus in the ethBusPerfTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

ethBusTrafficBuffer		1.1.22.101.2.2.12.5.1.1.3
Record of traffic for the last second with a resolution of 100 msec. The traffic is expressed in percents of the maximum Ethernet traffic and each record contains 10 readings, in the range 1..20, expressed on a log(10) scale ( value = 10*log10(percent) ).
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

ethBusTrafficThresh		1.1.22.101.2.2.12.5.1.1.4
Traffic threshold value. When exceeded, a trap is send to the management console. Expressed in percents of the maximum Ethernet traffic, in the range 1..20, expressed on a log(10) scale.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

ethBusPeakTraffic		1.1.22.101.2.2.12.5.1.1.5
Maximal traffic value since last reset of hub or relay. Expressed in per- cents of the maximum Ethernet traffic, in the range 1..20, expressed on log(10) scale.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ethBusTotalCollisions		1.1.22.101.2.2.12.5.1.1.6
Counter incremented every time the hub enters a condition caused by simultaneous transmission and detection of external activity on one or more of its ports.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

ethBusTotalPackets		1.1.22.101.2.2.12.5.1.1.7
Counter for number of packets (good and errors) detected on the Ethernet bus.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

ethBusTotalErrors		1.1.22.101.2.2.12.5.1.1.8
Counter for number of errors detected on the Ethernet bus. Does not take into account the collisions.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

ethBusTraffic		1.1.22.101.2.2.12.5.1.1.9
Last traffic reading (sampling time = 100 msec). The traffic is expressed in percents of the maximum Ethernet traffic in the range 1..20, expressed on a log(10) scale ( value = 10*log10(percent) ).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ethBusUtilization		1.1.22.101.2.2.12.5.1.1.10
Last traffic reading (sampling time = 100 msec). The traffic is expressed in percents of the maximum Ethernet traffic.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ethBusPeakUtilization		1.1.22.101.2.2.12.5.1.1.11
Maximal traffic value since last reset of agent. Expressed in percents of the maximum effective Ethernet traffic.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ethBusClockTable		1.1.22.101.2.2.12.5.2
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthBusClockEntry

ethBusClockEntry		1.1.22.101.2.2.12.5.2.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	EthBusClockEntry

ethBusClockBusId		1.1.22.101.2.2.12.5.2.1.1
ID of the bus in the ethBusClockTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

ethBusClockId		1.1.22.101.2.2.12.5.2.1.2
ID of the clock in the ethBusClockTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

ethBusClockTestResult		1.1.22.101.2.2.12.5.2.1.3
Values clockFailure and busFailure define the faulty statuses for clock tests. The test is performed by LCL100 module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), clockFailure(2), busFailure(3), notSupported(255)

tokRing		1.1.22.101.2.2.13.1
OBJECT IDENTIFIER

tokRingTable		1.1.22.101.2.2.13.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TokRingEntry

tokRingEntry		1.1.22.101.2.2.13.1.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	TokRingEntry

tokRingAgId		1.1.22.101.2.2.13.1.1.1.1
ID of the agent to which the ring belongs in the tokRingTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

tokRingId		1.1.22.101.2.2.13.1.1.1.2
ID of the ring in the tokRingTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

tokRingLeftSlot		1.1.22.101.2.2.13.1.1.1.3
Slot number of the left-most slot of the ring.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

tokRingRightSlot		1.1.22.101.2.2.13.1.1.1.4
Slot number of the right-most slot of the ring that has a lobe port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

tokRingTrafficBuffer		1.1.22.101.2.2.13.1.1.1.5
Record of traffic for the last second with a resolution of 100 msec. The traffic is expressed in percents of the maximum effective TR traffic (token messages are excluded) and each record contains 10 readings, in range 1..20 on log(10) scale.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

tokRingTrafficThresh		1.1.22.101.2.2.13.1.1.1.6
Traffic threshold value. When exceeded, a trap is send to the management console. Expressed in percents of the maximum effective TR traffic (token messages are excluded) in the range 1..20 on log(10) scale.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

tokRingPeakTraffic		1.1.22.101.2.2.13.1.1.1.7
Maximal traffic value since last reset of agent. Expressed in percents of the maximum effective TR traffic (token messages are excluded), in the range 1..20 on log(10) scale.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

tokRingNumberOfStations		1.1.22.101.2.2.13.1.1.1.8
Number of Token Ring stations (controllers) detected on the ring. The TR controller of the agent card is included in this count.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

tokRingConfiguration		1.1.22.101.2.2.13.1.1.1.9
Configuration attribute describing the list of physical addresses detected on the Token Ring. Coded in internal FIBRONICS application format.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

tokRingBeaconing		1.1.22.101.2.2.13.1.1.1.10
This attribute indicates if a beaconing condition is currently detected on the ring.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

tokRingBeaconingStation		1.1.22.101.2.2.13.1.1.1.11
The MAC address of the last station which was detected as sending Beaconing MAC frames on the ring.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

tokRingStationsMatch		1.1.22.101.2.2.13.1.1.1.12
This attribute indicates matching between the number of stations detected on the ring between the current agent and the next agent on Up Stream sense and the number of connected lobe ports.Used by the port address correlation mechanism.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

tokRingTraffic		1.1.22.101.2.2.13.1.1.1.13
Last traffic reading (sampling time = 100 msec). The traffic is expressed in percents of the maximum Ethernet traffic in the range 1..20, expressed on a log(10) scale ( value = 10*log10(percent) ).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

tokRingSecurityMethod		1.1.22.101.2.2.13.1.1.1.14
Security scheme selected by the user.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	perPort(1), perRing(2), disabled(3), notSupported(255)

tokRingSecurityPolicy		1.1.22.101.2.2.13.1.1.1.15
Security policy (trap only or trap and disconnect) selected for the ring. Coded in FIBRONICS internal format.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1)

tokRingSecureAddr		1.1.22.101.2.2.13.1.1.1.16
Secure addresses assigned to the ring. Coded in FIBRONICS internal format.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

tokRingLastViolation		1.1.22.101.2.2.13.1.1.1.17
MAC address of a last detected intruder.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

tokRingUtilization		1.1.22.101.2.2.13.1.1.1.18
Last traffic reading (sampling time = 100 msec). The traffic is expressed in percents of the maximum Token Ring traffic.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

tokRingPeakUtilization		1.1.22.101.2.2.13.1.1.1.19
Maximal traffic value since last reset of agent. Expressed in percents of the maximum effective TR traffic (token messages are excluded).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

tokGroup		1.1.22.101.2.2.13.2
OBJECT IDENTIFIER

tokGroupTable		1.1.22.101.2.2.13.2.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TokGroupEntry

tokGroupEntry		1.1.22.101.2.2.13.2.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	TokGroupEntry

tokGroupId		1.1.22.101.2.2.13.2.1.1.1
Number of the slot in which the group is installed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

tokGroupAutoRightLoop		1.1.22.101.2.2.13.2.1.1.2
Value ON of this attribute signifies that a hardware loop was automatically created on a Token Ring module which does not sense the existence of another token ring group on the right hand side.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

tokGroupAutoLeftLoop		1.1.22.101.2.2.13.2.1.1.3
Value ON of this attribute signifies that a hardware loop was automatically created on a Token Ring module which does not sense the existence of another token ring group on the left hand side.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

tokGroupManRightLoop		1.1.22.101.2.2.13.2.1.1.4
Setting this attribute to ON signifies a command to the hardware to create a loop on the Token Ring module which isolates the ring from the right hand side.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

tokGroupManLeftLoop		1.1.22.101.2.2.13.2.1.1.5
Setting this attribute to ON signifies a command to the hardware to create a loop on the Token Ring module which isolates the ring from the left hand side.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

tokGroupRightNeighbor		1.1.22.101.2.2.13.2.1.1.6
Attribute defining the existence of a neighbor another token ring group on the right hand side of the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	exist(1), notExist(2)

tokGroupLeftNeighbor		1.1.22.101.2.2.13.2.1.1.7
Attribute defining the existence of a neighbor another token ring group on the left hand side of the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	exist(1), notExist(2)

tokGroupIOMode		1.1.22.101.2.2.13.2.1.1.8
Attribute defining the I/O mode (single, dual-ring-in, dual-ring-out) Lobe, Internal Repeater or Star) of a module from the the LTR-IO family.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	single(1), dualRingIn(2), dualRingOut(3), illegalMode(4), lobe(5), intRepeater(6), star(7), notSupported(255)

tokGroupBridgeMode		1.1.22.101.2.2.13.2.1.1.9
Attribute describing the operational mode of the bridge. For ITLB the following modes are defined: - Mode A: First channel connected to an external ring (RI,RO connectors) and second channel connected to an internal ring; - Mode B: First channel connected to an external ring by a DTE connector and second channel connected to an internal ring; - Mode C: First channel connected to an internal left ring and second channel connected to an internal right ring.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	modeA(1), modeB(2), modeC(3), notSupported(255)

tokGroupManLinkLoop		1.1.22.101.2.2.13.2.1.1.10
Setting the value of this attribute to ON instructs the hardware of a FIBRONICS Token Ring repeater module to close the loop in the direction of the external connection.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

tokGroupManBusLoop		1.1.22.101.2.2.13.2.1.1.11
Setting the value of this attribute to ON instructs the hardware of a FIBRONICS Token Ring repeater module to close the loop in the direction of the internal bus.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

tokGroupAutoLinkLoop		1.1.22.101.2.2.13.2.1.1.12
Value ON of this attribute signifies that a hardware loop has been auto- matically closed by the hardwar of the FIBRONICS Token Ring repeater as a result of problems on the external link.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

tokGroupAutoBusLoop		1.1.22.101.2.2.13.2.1.1.13
Value ON of this attribute signifies that a hardware loop has been auto- matically closed by the hardware of the FIBRONICS Token Ring repeater as a result of problems on the internal bus.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

tokGroupSpecificOID		1.1.22.101.2.2.13.2.1.1.14
This attribute provides the OID of another group containing additional more specific information regarding this instance.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

tokGroupRingTable		1.1.22.101.2.2.13.2.2
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TokGroupRingEntry

tokGroupRingEntry		1.1.22.101.2.2.13.2.2.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	TokGroupRingEntry

tokGroupRingGroupId		1.1.22.101.2.2.13.2.2.1.1
ID of the group to which the ring belongs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

tokGroupRingId		1.1.22.101.2.2.13.2.2.1.2
ID of the ring.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

tokGroupRingSpeed		1.1.22.101.2.2.13.2.2.1.3
Attribute describing the bandwidth of the ring.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), oneMegabit(2), fourMegabit(3), sixteenMegabit(4), sixteenMgbEarly(5)

tokGroupRingInserted		1.1.22.101.2.2.13.2.2.1.4
Indicates that the bridge interface has inserted itself into the ring.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notInserted(1), inserted(2)

tokPort		1.1.22.101.2.2.13.3
OBJECT IDENTIFIER

tokPortTable		1.1.22.101.2.2.13.3.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TokPortEntry

tokPortEntry		1.1.22.101.2.2.13.3.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	TokPortEntry

tokPortGroupId		1.1.22.101.2.2.13.3.1.1.1
ID of the group to which the token ring port belongs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

tokPortId		1.1.22.101.2.2.13.3.1.1.2
ID of the port in the tokPortTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

tokPortBypass		1.1.22.101.2.2.13.3.1.1.3
Setting the value of this attribute to ON causes the by- passing of the TokenRing FIBRONICS port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

tokPortConnected		1.1.22.101.2.2.13.3.1.1.4
Attribute which describes the connection status of a Token Ring port (inclusion of the Token Ring controller in the ring).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	connected(1), notConnected(2), notSupported(255)

tokPortTCP		1.1.22.101.2.2.13.3.1.1.5
Setting the value of this attribute to ON causes the activation of the cable-fault detection mechanism.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

tokPortCableFault		1.1.22.101.2.2.13.3.1.1.6
Value ON of this attribute signifies the detection of a cable-fault on this specific Token Ring port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

tokPortFunctionalStatus		1.1.22.101.2.2.13.3.1.1.7
The value of this attribute reflects the functional status of FIBRONICS Token Ring ports. Note that it is not mandatory that a certain port support all the enumerated states. Here is the lest of the possible states: OK - fully functional port, transmitting and receiving packets. RLD - receive link down condition on the port. TLD - transmit link down condition on the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), rld(2), tld(4), notSupported(255)

tokPortLastSourceAddr		1.1.22.101.2.2.13.3.1.1.8
MAC source address of the last readable frame received by this port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

tokPortSpecificOID		1.1.22.101.2.2.13.3.1.1.9
This attribute provides the OID of another group containing additional more specific information regarding this instance.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

tokPortRingSpeedError		1.1.22.101.2.2.13.3.1.1.10
This attribute is set to 'on' when the station tries to enter the ring with the speed different from the ring's one.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

tsGroup		1.1.22.101.2.2.14.1
OBJECT IDENTIFIER

tsGroupTable		1.1.22.101.2.2.14.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TsGroupEntry

tsGroupEntry		1.1.22.101.2.2.14.1.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	TsGroupEntry

tsGroupId		1.1.22.101.2.2.14.1.1.1.1
Number of the slot in which the group is installed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

tsGroupLATStatus		1.1.22.101.2.2.14.1.1.1.2
Value ON of this attribute means that LAT protocol is Enabled on the FIBRONICS Ethernet module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

tsGroupOperationMode		1.1.22.101.2.2.14.1.1.1.3
This attribute describes the operation mode of the module in a multiprocessor configuration sensor, as reported by interprocessors communication.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	diagnostics(1), diagnosticsFailure(2), loading(3), loadingFailure(4), operational(5)

ltalkPort		1.1.22.101.2.2.15.1
OBJECT IDENTIFIER

ltalkPortTable		1.1.22.101.2.2.15.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LtalkPortEntry

ltalkPortEntry		1.1.22.101.2.2.15.1.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LtalkPortEntry

ltalkPortGroupId		1.1.22.101.2.2.15.1.1.1.1
Number of the group to which the port belongs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

ltalkPortId		1.1.22.101.2.2.15.1.1.1.2
ID of the port in the ltalkPortTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

ltalkPortTest		1.1.22.101.2.2.15.1.1.1.3
A value ON of this attribute indicates that a port test should be performed upon the port defined by the attribute instance.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

ltalkPortTestResult		1.1.22.101.2.2.15.1.1.1.4
Indicates the result of a port test performed on this port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), faulty(2)

ltalkPortJam		1.1.22.101.2.2.15.1.1.1.5
An ON value of this attribute indicates a Jam error on the specific port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

clGroup		1.1.22.101.2.2.16.1
OBJECT IDENTIFIER

clGroupTable		1.1.22.101.2.2.16.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ClGroupEntry

clGroupEntry		1.1.22.101.2.2.16.1.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ClGroupEntry

clGroupId		1.1.22.101.2.2.16.1.1.1.1
Number of the slot in which the group is installed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

clGroupClockRedundancy		1.1.22.101.2.2.16.1.1.1.2
Value ON of this attribute defines a redundancy (backup) relationship between the internal and external clocks on the LCL100 module.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

clGroupMainClock		1.1.22.101.2.2.16.1.1.1.3
Value of this attribute is an index into clPortTable, and defines the clock that should operate or a main clock in redundancy scheme. Serves as 'Clock selection' switch on the card.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

clGroupTestClocks		1.1.22.101.2.2.16.1.1.1.4
A value ON of this attribute indicates that a test should be performed on all clock ports.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

clPort		1.1.22.101.2.2.16.2
OBJECT IDENTIFIER

clPortTable		1.1.22.101.2.2.16.2.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ClPortEntry

clPortEntry		1.1.22.101.2.2.16.2.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ClPortEntry

clPortGroupId		1.1.22.101.2.2.16.2.1.1.1
Number of the group to which the port belongs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

clPortId		1.1.22.101.2.2.16.2.1.1.2
ID of the port in the clPortTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

clPortFunctionalStatus		1.1.22.101.2.2.16.2.1.1.3
Indicates whether the clock is faulty or not.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), faulty(2)

lBoxOID		1.1.22.101.2.2.17.1
OBJECT IDENTIFIER

lUnknownBoxOID		1.1.22.101.2.2.17.1.1
OBJECT IDENTIFIER

lLET18BoxOID		1.1.22.101.2.2.17.1.2
OBJECT IDENTIFIER

lLET3BoxOID		1.1.22.101.2.2.17.1.3
OBJECT IDENTIFIER

lLET36BoxOID		1.1.22.101.2.2.17.1.4
OBJECT IDENTIFIER

lLET18EBoxOID		1.1.22.101.2.2.17.1.5
OBJECT IDENTIFIER

lLERT40BoxOID		1.1.22.101.2.2.17.1.6
OBJECT IDENTIFIER

lLET10BoxOID		1.1.22.101.2.2.17.1.7
OBJECT IDENTIFIER

lFDX100BoxOID		1.1.22.101.2.2.17.1.8
OBJECT IDENTIFIER

lSTACKBoxOID		1.1.22.101.2.2.17.1.9
OBJECT IDENTIFIER

iwb		1.1.22.101.2.2.21.1
OBJECT IDENTIFIER

iwr		1.1.22.101.2.2.21.2
OBJECT IDENTIFIER

itr		1.1.22.101.2.2.21.3
OBJECT IDENTIFIER

iwrGroupTable		1.1.22.101.2.2.21.2.1
Attributes pertaining to the module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IwrGroupEntry

iwrGroupEntry		1.1.22.101.2.2.21.2.1.1
An entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IwrGroupEntry

iwrGroupId		1.1.22.101.2.2.21.2.1.1.1
Slot number in which the module is located.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

iwrOperState		1.1.22.101.2.2.21.2.1.1.2
One of the possible states of the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	run(1), boot(2), fail(3)

iwrPMState		1.1.22.101.2.2.21.2.1.1.3
The state of the Processor Module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), fail(2)

iwrIOMState		1.1.22.101.2.2.21.2.1.1.4
The state of the Input/Output Module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), fail(2)

iwrWANTable		1.1.22.101.2.2.21.2.2
WAN data table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IwrWANEntry

iwrWANEntry		1.1.22.101.2.2.21.2.2.1
Entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IwrWANEntry

iwrWANGroupId		1.1.22.101.2.2.21.2.2.1.1
Slot number in which the module is located.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

iwrWANPortId		1.1.22.101.2.2.21.2.2.1.2
WAN port index.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

iwrWANConnection		1.1.22.101.2.2.21.2.2.1.3
WAN connection status.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	connected(1), disconnected(2)

iwrWANPortCableType		1.1.22.101.2.2.21.2.2.1.4
Cable type connected to the specified WAN port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	x21(1), rs232(2), v35(3)

itrGroupTable		1.1.22.101.2.2.21.3.1
Table of attributes pertaining to the ITRE module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ItrGroupEntry

itrGroupEntry		1.1.22.101.2.2.21.3.1.1
An entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ItrGroupEntry

itrGroupId		1.1.22.101.2.2.21.3.1.1.1
Slot number in which the module is located.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

itrMainSWVersion		1.1.22.101.2.2.21.3.1.1.2
Software version of the main CPU.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

itrConfigState		1.1.22.101.2.2.21.3.1.1.3
Configuration state of the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	local(1), remote(2), notSupported(255)

itrModuleState		1.1.22.101.2.2.21.3.1.1.4
State of the ISTC/IFTC modules.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	oper(1), load(2), setup(3), notSupported(255)

itrLinkTable		1.1.22.101.2.2.21.3.2
ITRE links table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ItrLinkEntry

itrLinkEntry		1.1.22.101.2.2.21.3.2.1
Entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ItrLinkEntry

itrLinkGroupId		1.1.22.101.2.2.21.3.2.1.1
Slot number in which the module is located.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

itrLinkPortId		1.1.22.101.2.2.21.3.2.1.2
Link identifier.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

itrLinkIf		1.1.22.101.2.2.21.3.2.1.3
Interface type.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	v11(1), v24(2), v35(3), dte-dce(4)

itrLinkMode		1.1.22.101.2.2.21.3.2.1.4
Synchronous or asynchronous modes on the link.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	sync(1), async(2)

itrLinkAsyncRate		1.1.22.101.2.2.21.3.2.1.5
Possible link speeds that can be set in asynchronous mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	r2400(1), r4800(2), r9600(3), r14400(4), r19200(5), r38400(6), r56000(7), r57600(8), r64000(9), r112000(10), unknown(255)

itrLinkSyncRate		1.1.22.101.2.2.21.3.2.1.6
Link speeds in synchronous mode.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	r1200(1), r2400(2), r4800(3), r9600(4), r14400(5), r19200(6), r38400(7), r48000(8), r56000(9), r57600(10), r64000(11), r112000(12), r128000(13), r256000(14), r384000(15), r512000(16), r786000(17), r1024000(18), r1544000(19), r2048000(20), unknown(255)

itrLinkParity		1.1.22.101.2.2.21.3.2.1.7
This attribute enables/disables parity checking.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

itrLinkParityEvenOdd		1.1.22.101.2.2.21.3.2.1.8
Even or odd parity.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	even(1), odd(2), notSupported(255)

itrLinkStopBit		1.1.22.101.2.2.21.3.2.1.9
Number of stop bits (1 or 2 ) in asynchronous mode. The value 'none' is returned in synchronous mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	one(1), two(2), none(3), notSupported(255)

itrLinkRemoteLANConn		1.1.22.101.2.2.21.3.2.1.10
This attribute shows whether the remote ITRE is connected to the LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	connected(1), disconnected(2), notSupported(255)

itrLinkFunctionalStatus		1.1.22.101.2.2.21.3.2.1.11
The attribute represents the status of the WAN link.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), fail(2), noRxClk(3)

lse		1.1.22.101.2.2.19.1
OBJECT IDENTIFIER

lseGroupTable		1.1.22.101.2.2.19.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LseGroupEntry

lseGroupEntry		1.1.22.101.2.2.19.1.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LseGroupEntry

lseGroupId		1.1.22.101.2.2.19.1.1.1.1
Slot number in which the group is installed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lseGroupFastOpen		1.1.22.101.2.2.19.1.1.1.2
Setting the value of this attribute to ON activates the port for short idle time when code violation was detected.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseGroup10MSqlt		1.1.22.101.2.2.19.1.1.1.3
Setting the value of this attribute to ON activates the mechanism of detection preamble of 10Mhz.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseGroupSmartSqlt		1.1.22.101.2.2.19.1.1.1.4
Control the mechnism of the input sensitivity of the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseGroupCParameter		1.1.22.101.2.2.19.1.1.1.5
Defines the number of consecutive collisions the port waits before it ceases transmitting of 512 bits time toward the station.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..8

lseGroupIPGJamLength		1.1.22.101.2.2.19.1.1.1.6
Defines the IPG jam length in Ethernet bit time (100nS) start at 16 bit time in steps of 16 to 112 bit time. Any number between the defined values will take to nearest smaller value.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	16..112

lseGroupJamLength		1.1.22.101.2.2.19.1.1.1.7
Defines the Jam Length in time start from 8 (800micro-seconds) to 120 (12mili-seconds). Each step of 8 is equal 800micro-seconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	8..120

lseGroupDataBlinderLength		1.1.22.101.2.2.19.1.1.1.8
Defines the Data Blinder Length in Ethernet bit time (100nS) start at 48 bit time in steps of 8 to 120 bit time. Any number between the defined values will take to nearest smaller value
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	48..120

lseGroupIPGDataLength		1.1.22.101.2.2.19.1.1.1.9
Defines the IPG data length in Ethernet bit time (100nS) start at 48 bit time in steps of 8 to 120 bit time. Any number between the defined values will take to nearest smaller value.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	48..120

lseGroupActiveMonitor		1.1.22.101.2.2.19.1.1.1.10
This attribute defines the status of the module which is the high-speed bus active monitor.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseGroupBackBone		1.1.22.101.2.2.19.1.1.1.11
The board is in the Backbone Mode. lse208 - upper subgroup is RX only (ports 1-4) and lower subgroup is TX to line only. lse808 - the first port is RX from line only, the second - TX to line only, the rest are in regular 10BaseT mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseGroupSetDefaults		1.1.22.101.2.2.19.1.1.1.12
Set all hardware parameters to their default values.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseIntPort		1.1.22.101.2.2.19.1.2
OBJECT IDENTIFIER

lseIntPortTable		1.1.22.101.2.2.19.1.2.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LseIntPortEntry

lseIntPortEntry		1.1.22.101.2.2.19.1.2.1.1
An entry in the table, containing data about a single internal LanSwitch bank.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LseIntPortEntry

lseIntPortGroupId		1.1.22.101.2.2.19.1.2.1.1.1
Id of the group to which the port belongs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

lseIntPortId		1.1.22.101.2.2.19.1.2.1.1.2
Number of LanSwitch port in the board.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

lseIntPortIOMode		1.1.22.101.2.2.19.1.2.1.1.3
All packets on the high-speed bus that were not captured by any regular port are captured by the I/O port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseIntPortResetSwitchCAM		1.1.22.101.2.2.19.1.2.1.1.4
Acting like toggle switch thus always returns OFF
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseIntPortVideoPacket		1.1.22.101.2.2.19.1.2.1.1.5
Set all Tx packets toward the high-speed bus to video type packets.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseIntPortPriorityStateMachine		1.1.22.101.2.2.19.1.2.1.1.6
Setting the value of this attribute to ON activates the priority mechanism.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseIntPortActiveBroadcastPriority		1.1.22.101.2.2.19.1.2.1.1.7
Setting the value of this attribute to ON activates the active broadcast mode in priority mechanism.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseIntPortPriorityLevel		1.1.22.101.2.2.19.1.2.1.1.8
This attribute defines the priority levels of Tx packets toward the high-speed bus. The highest priority is broadcast.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	broadcast(1), multicast(2), video(3), regular(4), default(5), mngrTerminal(6), notSupported(255)

lseIntPortSuperPriorityEnable		1.1.22.101.2.2.19.1.2.1.1.9
The value ON defines the retry parameter for the priority level mechanism.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseIntPortRoutingMode		1.1.22.101.2.2.19.1.2.1.1.10
Generic - examines all the packets that are not members of any virtual network. Net - examines only the packets that have the port's network number.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	generic(1), net(2), dstPort(3), notSupported(255)

lseIntPortGlobal		1.1.22.101.2.2.19.1.2.1.1.11
Port in a network routing mode that examines all packets that are not members of all virtual networks.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseIntPortLearnIOCAM		1.1.22.101.2.2.19.1.2.1.1.12
The ability of an I/O port to learn incoming MAC addresses received in its port and store them in its CAM. The CAM is limited to total of 8 MAC addresses.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseIntPortSecurity		1.1.22.101.2.2.19.1.2.1.1.13
Setting the value of this attribute to ON activates the security mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseIntPortIgnoreBusy		1.1.22.101.2.2.19.1.2.1.1.14
Setting the value of this attribute to ON activates the ignore busy mode. The busy signal toward the high-speed bus is not activated even though the TX buffer is full.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseIntPortRetryPriorityLevel1		1.1.22.101.2.2.19.1.2.1.1.15
The port increases the priority level of the high-speed bus packets after the defined number (1..32) trials.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..32

lseIntPortRetryPriorityLevel2		1.1.22.101.2.2.19.1.2.1.1.16
The port increases the priority level of the high-speed bus packets after the defined number (1..32) trials.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..32

lseIntPortRetryPriorityLevel3		1.1.22.101.2.2.19.1.2.1.1.17
The port increases the priority level of the high-speed bus packets after the defined number (1..32) trials.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..32

lseIntPortIgnoreProtocolType		1.1.22.101.2.2.19.1.2.1.1.18
Any packet regardless of thye protocol type is received from the high-speed bus.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ignore(1), not-ignore(2), notSupported(255)

lseIntPortCompanyMAC		1.1.22.101.2.2.19.1.2.1.1.19
The attribute defines the first three bytes of the MAC address of the video host server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

lseIntPortTxSafetyZone		1.1.22.101.2.2.19.1.2.1.1.20
Defines the Tx Safety Zone in bits.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..1024

lseIntPortRxSafetyZone		1.1.22.101.2.2.19.1.2.1.1.21
Defines the Rx Safety Zone in bits.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..1024

lseIntPortTxBurstLength		1.1.22.101.2.2.19.1.2.1.1.22
Defines the TX Burst Length in bits.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..1024

lseIntPortSecurityIntruder		1.1.22.101.2.2.19.1.2.1.1.23
The value ON of this attribute reflects a security violation occurrence.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseIntPortJabber		1.1.22.101.2.2.19.1.2.1.1.24
Value ON of this attribute reflects the jabber transmitted to the port by the high-speed bus.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseIntPortCAM		1.1.22.101.2.2.19.1.2.1.1.25
Fifty six bytes of MAC addresses. Each byte with the port number is followed by six byte MAC address.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(56)

lseIntPortVideoStateMachine		1.1.22.101.2.2.19.1.2.1.1.26
Setting the value of this attribute to ON activates the video state machine mode. Received packets are filtered by demand from the station.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)

lseIntPortTransmitWeight		1.1.22.101.2.2.19.1.2.1.1.27
Defines the Transmit Weight of the frames toward the high-speed bus.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..127

lsePort		1.1.22.101.2.2.19.1.3
OBJECT IDENTIFIER

lsePortTable		1.1.22.101.2.2.19.1.3.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LsePortEntry

lsePortEntry		1.1.22.101.2.2.19.1.3.1.1
An entry in the table containing data about a single external switch port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LsePortEntry

lsePortGroupId		1.1.22.101.2.2.19.1.3.1.1.1
Id of the group to which the port belongs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

lsePortId		1.1.22.101.2.2.19.1.3.1.1.2
Number of LanSwitch port in the board.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

lsePortPolarity		1.1.22.101.2.2.19.1.3.1.1.3
Setting the value of this attribute to ON activates the automatic port polarity detection mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), notSupported(255)