Fore-Switch-MIB

File: Fore-Switch-MIB.mib (634610 bytes)

Imported modules

RFC1155-SMI SNMPv2-SMI SNMPv2-TC
IF-MIB Fore-Common-MIB Fore-TrapLog-MIB
Fore-Adapter-MIB Fore-Callrecord-MIB PNNI-MIB
HOST-RESOURCES-MIB

Imported symbols

Gauge Counter32 Gauge32
Unsigned32 IpAddress TimeTicks
Integer32 OBJECT-TYPE MODULE-IDENTITY
NOTIFICATION-TYPE TEXTUAL-CONVENTION DisplayString
PhysAddress TimeStamp TestAndIncr
RowStatus DateAndTime TimeInterval
ifIndex atmSwitch software
asxd hardware asx
SpansAddress NsapPrefix GeneralState
TransitNetwork NsapAddr EntryStatus
AtmSigProtocol IntegerBitString ConnectionType
systems trapLogIndex ipFilterStatsVPI
ipFilterStatsVCI ipFilterStatsIfName crMemoryAllocated
crXfrIndex crXfrPrimaryTrapStatus crXfrSecondaryTrapStatus
pnniNodeId hrSystemDate

Defined Types

E164Address  
E164 address format defined as 15 ASCII characters.
TEXTUAL-CONVENTION    
  OCTET STRING Size(15)  

AtmConnSchedMode  
The value of this object identifies the scheduling mode for an ATM connection (i.e., VCC or VPC). The possible values are default, roundrobin, guaranteed, and smoothed.
TEXTUAL-CONVENTION    
  INTEGER default(1), roundrobin(2), smoothed(3), guaranteed(4)  

AtmOrigPathSchedMode  
The value of this object identifies the scheduling mode for an originating path. The possible values are flat, shaped and shaped-roundrobin.
TEXTUAL-CONVENTION    
  INTEGER flat(1), shaped(2), shaped-roundrobin(3)  

AAL5CountingMode  
The value of this object identifies the AAL5 counting mode for a connection (i.e., VCC or VPC). Possible values for this object are default, cell-counting and packet-counting.
TEXTUAL-CONVENTION    
  INTEGER default(1), cell-counting(2), packet-counting(3)  

BoardEntry  
SEQUENCE    
  boardIndex Integer32
  boardVersion Integer32
  boardModel INTEGER
  boardSerialNumber Integer32
  numberOfModules Integer32
  vpiLookupErrors Counter32
  vciLookupErrors Counter32
  boardControlPort Integer32
  boardHDCOMPAsicVersion Integer32
  boardMcastSpaceIndex Integer32

BoardStatsEntry  
SEQUENCE    
  boardStatsBoard Integer32
  boardStatsIndex Integer32
  boardStatsName DisplayString
  boardStatsValue Gauge32

PortCardEntry  
SEQUENCE    
  portCardIndex Integer32
  portCardName DisplayString
  portCardFlavor DisplayString
  portCardType DisplayString
  portCardUptime TimeTicks
  portCardSerialNumber DisplayString
  portCardAssemblyRevision Integer32
  portCardHardwareConf Integer32
  portCardState INTEGER

BoardTrafficManagementPerPriorityEntry  
SEQUENCE    
  btmPerPriorityBoard Integer32
  btmPerPriorityPriority Integer32
  btmPerPriorityFeature Integer32
  btmPerPriorityPriorityName DisplayString
  btmPerPriorityValue Integer32

MallocUtilEntry  
SEQUENCE    
  mallocPartId Integer32
  numBytesFree Integer32
  numBlocksFree Integer32
  maxBlockSizeFree Integer32
  numBytesAlloc Integer32
  numBlocksAlloc Integer32

ModuleEntry  
SEQUENCE    
  moduleBoard Integer32
  moduleNumber Integer32
  moduleName DisplayString
  moduleSpeed Unsigned32
  moduleNumberOfPorts Integer32
  moduleUptime TimeTicks
  moduleHwMajorRev Integer32
  moduleHwMinorRev Integer32
  moduleVersion INTEGER
  moduleTimingSupport INTEGER
  moduleProductNumber DisplayString
  moduleState INTEGER
  moduleSerialNumber DisplayString
  moduleTestAdminStatus INTEGER
  moduleTestOperStatus INTEGER
  moduleTestStatusText DisplayString
  moduleAttachState INTEGER
  moduleCLEI DisplayString

AppModuleEntry  
SEQUENCE    
  appModuleIndex Integer32
  appModuleName DisplayString
  appModuleOperState INTEGER
  appModuleStatusText DisplayString
  appModuleApplicationType DisplayString
  appModuleSoftwareVersion DisplayString
  appModuleBootSoftwareVersion DisplayString
  appModuleOosLed INTEGER
  appModulePanicAction INTEGER

OutputBufferEntry  
SEQUENCE    
  obufBoard Integer32
  obufNumber Integer32
  obufType Integer32
  obufOperStatus INTEGER
  obufBufferSize Integer32
  obufQueueLength Gauge32
  obufOverflows Gauge32
  obufPriorityName DisplayString
  obufName DisplayString

HwPortEntry  
SEQUENCE    
  hwPortBoard Integer32
  hwPortModule Integer32
  hwPortNumber Integer32
  hwPortVersion INTEGER
  hwPortModel INTEGER
  hwPortOperStatus INTEGER
  hwPortBufferSize Integer32
  hwPortQueueLength Gauge32
  hwPortOverflows Counter32
  hwPortErrors Counter32
  hwPortCarrier INTEGER
  hwPortGlobalIndex Integer32
  hwPortName DisplayString
  hwPortAdminStatus INTEGER
  hwPortTAXILoopback INTEGER
  hwPortLEDModel INTEGER
  hwPortTxLED INTEGER
  hwPortRxLED INTEGER
  hwPortIfIndex Integer32
  hwPortRxSyncLED INTEGER
  hwPortCounterResetTime TimeStamp
  hwPortCounterReset INTEGER
  hwPortSpeed Unsigned32

NetmodAlarmsEntry  
SEQUENCE    
  netmodSlot Integer32
  netmodSlotPriority INTEGER
  netmodStatus INTEGER
  netmodName DisplayString

HdcompEntry  
SEQUENCE    
  hdcompIndex Integer32
  hdcompDescr DisplayString
  hdcompAsicVersion Integer32
  hdcompVpiLookupErrors Counter32
  hdcompVciLookupErrors Counter32

SwAlarmEntry  
SEQUENCE    
  swAlarmType INTEGER
  swAlarmStatus INTEGER
  swAlarmMinorCategory INTEGER
  swAlarmMajorCategory INTEGER
  swAlarmReset INTEGER
  swAlarmCriticalCategory INTEGER
  swAlarmACOState INTEGER

SwAlarmRelayEntry  
SEQUENCE    
  swAlarmRelayIndex Integer32
  swAlarmRelayFunction INTEGER
  swAlarmRelayState INTEGER
  swAlarmRelayOperMode INTEGER

EnvPowerSupplyEntry  
SEQUENCE    
  envPowerSupplyIndex Integer32
  envPowerSupplyType INTEGER
  envPowerSupplyInputState GeneralState
  envPowerSupplyOutputState GeneralState
  envPowerSupplySerialNumber Integer32
  envPowerSupplyVersion Integer32
  envPowerSupplyCurrentState GeneralState
  envPowerSupply5VoltState GeneralState

EnvFanBanksEntry  
SEQUENCE    
  envFanBankIndex Integer32
  envFanBankState GeneralState
  envFanBankSerialNumber DisplayString
  envFanBankType Integer32
  envFanBankRevision Integer32

EnvTempSensorsEntry  
SEQUENCE    
  envTempSensorIndex INTEGER
  envTempSensorState INTEGER

EnvCPUsEntry  
SEQUENCE    
  envCpuBoard Integer32
  envCpuSlot Integer32
  envCpuType INTEGER
  envCPUState INTEGER
  envCpuDRAMSize Integer32
  envCpuRevLevel Integer32
  envCpuFlashSize Integer32
  envCpuBoardRevision Integer32
  envCpuPromRevision Integer32
  envCpuMACAddress PhysAddress
  envCpuSerialNumber DisplayString
  envCpuProductPartNumber DisplayString
  envCpuCLEI DisplayString
  envCpuIDESize Integer32

EnvFabricEntry  
SEQUENCE    
  envFabricIndex Integer32
  envFabricTemperature Integer32
  envFabricTemperatureState INTEGER

NetmodTimingEntry  
SEQUENCE    
  ntBoard Integer32
  ntModule Integer32
  ntPrimaryRecoveredClock Integer32
  ntSecondaryRecoveredClock Integer32
  ntPrimaryExportClock INTEGER
  ntSecondaryExportClock INTEGER
  ntGlobalClock INTEGER
  ntExportClockOperStatus INTEGER
  ntPrimaryImportClock INTEGER
  ntSecondaryImportClock INTEGER
  ntImportClockOperStatus INTEGER

BoardTimingEntry  
SEQUENCE    
  btBoard Integer32
  btPrimaryClock INTEGER
  btSecondaryClock INTEGER
  btPrimaryClockOperStatus INTEGER
  btSecondaryClockOperStatus INTEGER

ShmemConfEntry  
SEQUENCE    
  shmemConfIndex Integer32
  shmemUcastConnections Integer32
  shmemMcastConnections Integer32
  shmemVpiVciLists Integer32
  shmemCellsBuffers Integer32
  shmemConfName DisplayString
  shmemMemorySize Integer32

NetmodShmemEntry  
SEQUENCE    
  nshmemBoard Integer32
  nshmemModule Integer32
  nshmemConfRow Integer32
  nshmemConfSharedMemory Integer32
  nshmemCurrentUcastConnections Gauge32
  nshmemCurrentMcastConnections Gauge32
  nshmemCurrentVpiVciLists Gauge32
  nshmemCurrentCellsBuffers Gauge32
  nshmemCurrentSharedMemory Gauge32
  nshmemConfAal5PacketDrop Integer32
  nshmemAssertXACPT INTEGER
  nshmemMemorySize Integer32

PortShmemConfEntry  
SEQUENCE    
  pshmemConfBoard Integer32
  pshmemConfModule Integer32
  pshmemConfPort Integer32
  pshmemMaxCDVforCBR Integer32
  pshmemMaxCDVforVBR Integer32
  pshmemQsizeforABR Integer32
  pshmemEfciOnABR Integer32
  pshmemEfciOffABR Integer32
  pshmemQsizeforCBR Integer32
  pshmemQsizeforVBR Integer32
  pshmemClpThreshforCBR Integer32
  pshmemClpThreshforVBR Integer32
  pshmemClpThreshforABR Integer32
  pShmemAtmInterfaceIndex Integer32

PortShmemEntry  
SEQUENCE    
  pshmemBoard Integer32
  pshmemModule Integer32
  pshmemPort Integer32
  pshmemPriority INTEGER
  pshmemClpThreshold Integer32
  pshmemDedicatedQsize Integer32
  pshmemCurrentQsize Integer32
  pshmemTxCells Counter32
  pshmemLostCells Counter32

Shmem2ConfEntry  
SEQUENCE    
  shmem2ConfIndex Integer32
  shmem2UcastConnections Integer32
  shmem2McastConnections Integer32
  shmem2CellsBuffers Integer32
  shmem2ConfName DisplayString
  shmem2Counters Integer32
  shmem2CellMemorySize Integer32
  shmem2TableMemorySize Integer32
  shmem2NumPriorities Integer32

NetmodShmem2Entry  
SEQUENCE    
  nShmem2Board Integer32
  nShmem2Module Integer32
  nShmem2ConfRow Integer32
  nShmem2ConfSharedMemory Integer32
  nShmem2CurrentUcastConnections Gauge32
  nShmem2CurrentMcastConnections Gauge32
  nShmem2CurrentCellsBuffers Gauge32
  nShmem2CurrentSharedMemory Gauge32
  nShmem2ConfAal5PacketDrop Integer32
  nShmem2ConfAal5PacketDropforUBR Integer32
  nShmem2ConfEfciOn Integer32
  nShmem2ConfEfciOff Integer32
  nShmem2CellMemorySize Integer32
  nShmem2TableMemorySize Integer32
  nShmem2NumPriorities Integer32
  nShmem2VBRPriority INTEGER

PortShmem2ConfEntry  
SEQUENCE    
  pShmem2ConfBoard Integer32
  pShmem2ConfModule Integer32
  pShmem2ConfPort Integer32
  pShmem2QsizeforCBR Integer32
  pShmem2QsizeforVBR Integer32
  pShmem2QsizeforABR Integer32
  pShmem2QsizeforUBR Integer32
  pShmem2ClpThreshforCBR Integer32
  pShmem2ClpThreshforVBR Integer32
  pShmem2ClpThreshforABR Integer32
  pShmem2ClpThreshforUBR Integer32
  pShmem2AtmInterfaceIndex Integer32

PortPriorityShmem2ConfEntry  
SEQUENCE    
  ppShmem2ConfBoard Integer32
  ppShmem2ConfModule Integer32
  ppShmem2ConfPort Integer32
  ppShmem2ConfPriority INTEGER
  ppShmem2Qsize Integer32
  ppShmem2ClpThreshold Integer32

PortShmem2Entry  
SEQUENCE    
  pShmem2Board Integer32
  pShmem2Module Integer32
  pShmem2Port Integer32
  pShmem2Priority INTEGER
  pShmem2ClpThreshold Integer32
  pShmem2DedicatedQsize Integer32
  pShmem2CurrentQsize Integer32
  pShmem2TxCells Counter32
  pShmem2LostCells Counter32
  pShmem2IntentionalLostCells Counter32
  pShmem2UnintentionalLostCells Counter32

ChannelShmem2Entry  
SEQUENCE    
  vcShmem2OutputPort Integer32
  vcShmem2OutputVPI Integer32
  vcShmem2OutputVCI Integer32
  vcShmem2TotalLostCells Counter32
  vcShmem2IntentionalLostCells Counter32
  vcShmem2UnintentionalLostCells Counter32
  vcShmem2TransmittedCells Counter32

PathShmem2Entry  
SEQUENCE    
  vpShmem2OutputPort Integer32
  vpShmem2OutputVPI Integer32
  vpShmem2TotalLostCells Counter32
  vpShmem2IntentionalLostCells Counter32
  vpShmem2UnintentionalLostCells Counter32
  vpShmem2TransmittedCells Counter32

NetmodShmem2CustomBCSEntry  
SEQUENCE    
  nShmem2CustomBCSBoard Integer32
  nShmem2CustomBCSModule Integer32
  nShmem2CustomBCSValue Integer32
  nShmem2CustomBCSWeight Integer32
  nShmem2CustomBCSRowStatus RowStatus

Shmem3ConfEntry  
SEQUENCE    
  shmem3ConfIndex Integer32
  shmem3UcastConnections Integer32
  shmem3McastConnections Integer32
  shmem3VpiVciLists Integer32
  shmem3CellsBuffers Integer32
  shmem3ConfName DisplayString
  shmem3Counters Integer32
  shmem3CellMemorySize Integer32
  shmem3TableMemorySize Integer32

NetmodShmem3Entry  
SEQUENCE    
  nShmem3Board Integer32
  nShmem3Module Integer32
  nShmem3ConfRow Integer32
  nShmem3ConfSharedMemory Integer32
  nShmem3CurrentUcastConnections Gauge32
  nShmem3CurrentMcastConnections Gauge32
  nShmem3CurrentVpiVciLists Gauge32
  nShmem3CurrentCellsBuffers Gauge32
  nShmem3ConfAal5PacketDrop Integer32
  nShmem3ConfAal5PacketDropforUBR Integer32
  nShmem3ConfEfciOn Integer32
  nShmem3ConfEfciOff Integer32
  nShmem3CellMemorySize Integer32
  nShmem3TableMemorySize Integer32
  nShmem3ConfCountPackets INTEGER
  nShmem3ConfAltCLP1Threshold Integer32
  nShmem3ConfAltCLP01Threshold Integer32
  nShmem3ConfVcCLP1ForCBR Integer32
  nShmem3ConfVcCLP01ForCBR Integer32
  nShmem3ConfVcCLP1ForVBR Integer32
  nShmem3ConfVcCLP01ForVBR Integer32
  nShmem3ConfVcCLP1ForABR Integer32
  nShmem3ConfVcCLP01ForABR Integer32
  nShmem3ConfVcCLP1ForUBR Integer32
  nShmem3ConfVcCLP01ForUBR Integer32

PortShmem3ConfEntry  
SEQUENCE    
  pShmem3ConfBoard Integer32
  pShmem3ConfModule Integer32
  pShmem3ConfPort Integer32
  pShmem3QsizeforCBR Integer32
  pShmem3QsizeforVBR Integer32
  pShmem3QsizeforABR Integer32
  pShmem3QsizeforUBR Integer32
  pShmem3Clp01ThreshforCBR Integer32
  pShmem3Clp1ThreshforCBR Integer32
  pShmem3Clp01ThreshforVBR Integer32
  pShmem3Clp1ThreshforVBR Integer32
  pShmem3Clp01ThreshforABR Integer32
  pShmem3Clp1ThreshforABR Integer32
  pShmem3Clp01ThreshforUBR Integer32
  pShmem3Clp1ThreshforUBR Integer32
  pShmem3RateLimit Integer32
  pShmem3ConfSVCSchedulingCBR INTEGER
  pShmem3ConfPVCSchedulingCBR INTEGER
  pShmem3ConfSVCSchedulingVBR INTEGER
  pShmem3ConfPVCSchedulingVBR INTEGER
  pShmem3ConfAltCLPConfigCBR INTEGER
  pShmem3ConfAltCLPConfigVBR INTEGER
  pShmem3ConfAltCLPConfigUBR INTEGER
  pShmem3AtmInterfaceIndex Integer32

PortShmem3Entry  
SEQUENCE    
  pShmem3Board Integer32
  pShmem3Module Integer32
  pShmem3Port Integer32
  pShmem3Priority INTEGER
  pShmem3CurrentQsize Integer32
  pShmem3TxCells Counter32
  pShmem3EPDLostCells Counter32
  pShmem3CLP01LostCells Counter32
  pShmem3CLP1LostCells Counter32
  pShmem3VcCLPLostCells Counter32
  pShmem3OverflowLostCells Counter32
  pShmem3PPDLostCells Counter32

ChannelShmem3Entry  
SEQUENCE    
  vcShmem3OutputPort Integer32
  vcShmem3OutputVPI Integer32
  vcShmem3OutputVCI Integer32
  vcShmem3IntentionalLostCells Counter32
  vcShmem3UnintentionalLostCells Counter32
  vcShmem3CLP0TxCells Counter32
  vcShmem3CLP1TxCells Counter32
  vcShmem3EPDLostCells Counter32
  vcShmem3CLP1LostCells Counter32
  vcShmem3CLP01LostCells Counter32
  vcShmem3TransmittedPackets Counter32
  vcShmem3CurrentQsize Integer32

PathShmem3Entry  
SEQUENCE    
  vpShmem3OutputPort Integer32
  vpShmem3OutputVPI Integer32
  vpShmem3UnintentionalLostCells Counter32
  vpShmem3CLP0TxCells Counter32
  vpShmem3CLP1TxCells Counter32
  vpShmem3CLP1LostCells Counter32
  vpShmem3CLP01LostCells Counter32
  vpShmem3TransmittedPackets Counter32
  vpShmem3CurrentQsize Integer32

NetmodGenericShmemEntry  
SEQUENCE    
  nGenericShmemBoard Integer32
  nGenericShmemModule Integer32
  nGenericShmemSubindex Integer32
  nGenericShmemCurrentUcastConnections Integer32
  nGenericShmemCurrentMcastConnections Integer32
  nGenericShmemCurrentConnections Integer32
  nGenericShmemMaxUcastConnections Integer32
  nGenericShmemMaxMcastConnections Integer32
  nGenericShmemMaxConnections Integer32

NetmodGenericShmemCustomBCSEntry  
SEQUENCE    
  nGenericShmemCustomBCSBoard Integer32
  nGenericShmemCustomBCSModule Integer32
  nGenericShmemCustomBCSSubindex Integer32
  nGenericShmemCustomBCSValue Integer32
  nGenericShmemCustomBCSWeight Integer32
  nGenericShmemCustomBCSRowStatus RowStatus

DualScpConfEntry  
SEQUENCE    
  dualScpSlot INTEGER
  dualScpState INTEGER
  dualScpSyncState DisplayString
  dualScpPrimary INTEGER
  dualScpFailover INTEGER
  dualScpManualSyncRequest INTEGER
  dualScpCdbSyncMode INTEGER
  dualScpManualSwitchOver INTEGER
  dualScpSwitchOverTime DateAndTime
  dualScpSwitchOverThreshold Integer32
  dualScpSyncRequestList IntegerBitString
  dualScpNumSyncRequests Counter32
  dualScpNumSyncFailures Counter32
  dualScpResetStandbyScp INTEGER
  dualScpAutoRemoveOldFiles INTEGER
  dualScpRedundancyState DisplayString
  dualScpSVXCPStateSyncPercent Gauge
  dualScpSVXCPStateTransferFailed INTEGER
  dualScpSVXCPdroppedCallCount Integer32

GenericPortGroupConfEntry  
SEQUENCE    
  genericPortGroupBoard Integer32
  genericPortGroupIndex Integer32
  genericPortGroupSubindex Integer32
  genericPortGroupPrioIndex Integer32
  genericPortGroupAal5PacketDrop Integer32
  genericPortGroupEfciOn Integer32
  genericPortGroupEfciOff Integer32
  genericPortGroupPrioName DisplayString

GenericOutputPortConfEntry  
SEQUENCE    
  genericOutputPortConfBoard Integer32
  genericOutputPortConfModule Integer32
  genericOutputPortConfPort Integer32
  genericOutputPortConfPrio Integer32
  genericOutputPortConfPrioDedicatedQSize Integer32
  genericOutputPortConfPrioClp1Threshold Integer32
  genericOutputPortConfPrioClp01Threshold Integer32
  genericOutputPortConfPrioName DisplayString
  genericOutputPortConfAtmif Integer32

GenericOutputPortStatsEntry  
SEQUENCE    
  genericOutputPortStatsBoard Integer32
  genericOutputPortStatsModule Integer32
  genericOutputPortStatsPort Integer32
  genericOutputPortStatsPrio Integer32
  genericOutputPortStatsPrioTransmittedCells Counter32
  genericOutputPortStatsPrioClp1LostCells Counter32
  genericOutputPortStatsPrioClp01LostCells Counter32
  genericOutputPortStatsPrioName DisplayString
  genericOutputPortStatsAtmif Integer32
  genericOutputPortStatsPrioEpdPpdLostCells Counter32

SwitchDebounceEntry  
SEQUENCE    
  switchDebounceIndex Integer32
  switchDebounceName DisplayString
  switchDebounceHysteresis Integer32

McastSpaceEntry  
SEQUENCE    
  mcastSpaceIndex Integer32
  mcastSpaceNumConn Integer32
  mcastSpaceName DisplayString

SwitchSbprServerAddressEntry  
SEQUENCE    
  sbprServerAddressIndex Integer32
  sbprServerAddressIndexName DisplayString
  sbprServerMaxHops INTEGER
  sbprServerMinSeconds INTEGER
  sbprServerAddress1 IpAddress
  sbprServerAddress2 IpAddress
  sbprServerAddress3 IpAddress
  sbprServerAddress4 IpAddress
  sbprServerAddress5 IpAddress
  sbprServerRowStatus RowStatus

ServiceCategoryEntry  
SEQUENCE    
  serviceCategoryIndex Integer32
  serviceCategoryName DisplayString

PortEntry  
SEQUENCE    
  portNumber Integer32
  portAdminStatus INTEGER
  portOperStatus INTEGER
  portTime TimeTicks
  portRemoteAtmAddress SpansAddress
  portRemoteIpAddress IpAddress
  portMaxPathsIn Integer32
  portNumPathsIn Gauge32
  portMaxBandwidthIn Integer32
  portAllocBandwidthIn Gauge32
  portUsedBandwidthIn Gauge32
  portReceivedCells Counter32
  portMaxPathsOut Integer32
  portNumPathsOut Gauge32
  portMaxBandwidthOut Integer32
  portAllocBandwidthOut Gauge32
  portUsedBandwidthOut Gauge32
  portTransmittedCells Counter32
  portHwBoard Integer32
  portHwModule Integer32
  portHwNumber Integer32
  portILMIRemoteIpAddress IpAddress
  portCDVT Integer32
  portInputPolicingStatus INTEGER
  portVbrOverbooking INTEGER
  portVbrBufferOverb INTEGER
  portManagementStatus INTEGER
  portAISRDIGeneration INTEGER
  portInputCdv Integer32
  portInputMaxctd Integer32
  portInputDelayMode INTEGER
  portOutputCdv Integer32
  portOutputMaxctd Integer32
  portOutputDelayMode INTEGER
  portInputCACErrors Counter32
  portInputVPIErrors Counter32
  portInputVCIErrors Counter32
  portInputSetupErrors Counter32
  portOutputCACErrors Counter32
  portOutputVPIErrors Counter32
  portOutputVCIErrors Counter32
  portOutputSetupErrors Counter32
  portGCRAPolicingCBR INTEGER
  portGCRAPolicingVBR INTEGER
  portAAL5PacketDiscardCBR INTEGER
  portAAL5PacketDiscardVBR INTEGER
  portAAL5PacketDiscardUBR INTEGER
  portPPPolicingCBR INTEGER
  portPPPolicingVBR INTEGER
  portUBRTagging INTEGER
  portCACStatus INTEGER
  portCounterResetTime TimeStamp
  portCounterReset INTEGER
  portName DisplayString
  portGCRAPolicingRTVBR INTEGER
  portGCRAPolicingNRTVBR INTEGER
  portAAL5PacketDiscardRTVBR INTEGER
  portAAL5PacketDiscardNRTVBR INTEGER
  portPPPolicingRTVBR INTEGER
  portPPPolicingNRTVBR INTEGER
  portNrtVbrOverbooking INTEGER
  portNrtVbrBufferOverb INTEGER
  portRtVbrOverbooking INTEGER
  portRtVbrBufferOverb INTEGER
  portPathOverbooking INTEGER

AtmIfConnSchedEntry  
SEQUENCE    
  atmIfConnSchedLink Integer32
  atmIfConnSchedServCat Integer32
  atmIfConnSchedMode AtmConnSchedMode
  atmIfConnSchedOverride INTEGER

IfIndexMapEntry  
SEQUENCE    
  ifIndexMapIndex Integer32
  ifIndexMapBoard Integer32
  ifIndexMapNetmod Integer32
  ifIndexMapPort Integer32

CbrctConfEntry  
SEQUENCE    
  cbrctState INTEGER
  cbrctIdleDetection INTEGER
  cbrctIdleMask Integer32
  cbrctNoOfIdlePatterns Integer32
  cbrctIdlePatterns Integer32
  cbrctIdleIntPeriod TimeInterval
  cbrctActiveIntPeriod TimeInterval

AsxAtmIfEntry  
SEQUENCE    
  asxAtmIfName DisplayString
  asxAtmIfLinkid Integer32

PathEntry  
SEQUENCE    
  pathPort Integer32
  pathVPI Integer32
  pathStatus EntryStatus
  pathNumOutputs Gauge32
  pathMaxChannels Integer32
  pathNumChannels Gauge32
  pathMaxBandwidth Integer32
  pathAllocBandwidth Gauge32
  pathUsedBandwidth Gauge32
  pathCells Counter32
  pathUptime TimeTicks
  pathSigProtocol AtmSigProtocol
  pathRejectedCells Counter32
  pathMinVCI Integer32
  pathMaxVCI Integer32
  pathCACErrors Counter32
  pathVCIErrors Counter32
  pathSetupErrors Counter32

PathRouteEntry  
SEQUENCE    
  pathrInputPort Integer32
  pathrInputVPI Integer32
  pathrOutputPort Integer32
  pathrOutputVPI Integer32
  pathrStatus EntryStatus
  pathrMaxBandwidth Integer32
  pathrAllocBandwidth Gauge32
  pathrCells Counter32
  pathrUptime TimeTicks
  pathrSigProtocol AtmSigProtocol
  pathrRejectedCells Counter32
  pathrLoopVPI Integer32
  pathrUpcContract Integer32
  pathrName OCTET STRING
  pathrConnectionType ConnectionType
  pathrServCat Integer32

OutputPathEntry  
SEQUENCE    
  opathPort Integer32
  opathVPI Integer32
  opathStatus EntryStatus
  opathMaxChannels Integer32
  opathNumChannels Gauge32
  opathMaxBandwidth Integer32
  opathAllocBandwidth Gauge32
  opathUsedBandwidth Gauge32
  opathCells Counter32
  opathUptime TimeTicks
  opathSigProtocol AtmSigProtocol
  opathRejectedCells Counter32
  opathTrafficShapeVPI Integer32
  opathVbrOverbooking INTEGER
  opathVbrBufferOverb INTEGER
  opathMinVCI Integer32
  opathMaxVCI Integer32
  opathCACErrors Counter32
  opathVCIErrors Counter32
  opathSetupErrors Counter32
  opathLoopVPI Integer32
  opathSchedMode AtmOrigPathSchedMode
  opathNrtVbrOverbooking INTEGER
  opathNrtVbrBufferOverb INTEGER
  opathRtVbrOverbooking INTEGER
  opathRtVbrBufferOverb INTEGER

OutputPathStatsEntry  
SEQUENCE    
  opathStatsPort Integer32
  opathStatsVPI Integer32
  opathStatsLostCells Counter32
  opathStatsTransmittedCells Counter32
  opathStatsIntentionalLostCells Counter32
  opathStatsCLP0Cells Counter32
  opathStatsLostPackets Counter32
  opathStatsTransmittedPackets Counter32

OutputPathChannelSchedEntry  
SEQUENCE    
  opathChannelSchedPort Integer32
  opathChannelSchedVPI Integer32
  opathChannelSchedServCat Integer32
  opathChannelSchedSchedMode AtmConnSchedMode
  opathChannelSchedSchedOverride INTEGER

ChannelEntry  
SEQUENCE    
  chanPort Integer32
  chanVPI Integer32
  chanVCI Integer32
  chanStatus EntryStatus
  chanNumOutputs Gauge32
  chanAllocBandwidth Gauge32
  chanUsedBandwidth Gauge32
  chanCells Counter32
  chanUptime TimeTicks
  chanSigProtocol AtmSigProtocol
  chanRejectedCells Counter32
  chanCDV Integer32
  chanPolicingAction INTEGER
  chanUpcContract Integer32
  chanServCat Integer32
  chanQosCDVT Integer32
  chanQosPoliceState INTEGER
  chanQosPoliceScheme INTEGER
  chanQosPCR Integer32
  chanQosSCR Integer32
  chanQosMBS Integer32
  chanQosIsAAL5 INTEGER
  chanQosPerPacketPolicing INTEGER

ChannelRouteEntry  
SEQUENCE    
  chanrInputPort Integer32
  chanrInputVPI Integer32
  chanrInputVCI Integer32
  chanrOutputPort Integer32
  chanrOutputVPI Integer32
  chanrOutputVCI Integer32
  chanrStatus EntryStatus
  chanrSigProtocol AtmSigProtocol
  chanrName OCTET STRING
  chanrConnectionType ConnectionType

ReverseChannelRouteEntry  
SEQUENCE    
  revChanrOutputPort Integer32
  revChanrOutputVPI Integer32
  revChanrOutputVCI Integer32
  revChanrInputPort Integer32
  revChanrInputVPI Integer32
  revChanrInputVCI Integer32
  revChanrSigProtocol AtmSigProtocol

OutputChannelStatsEntry  
SEQUENCE    
  ochanStatsPort Integer32
  ochanStatsVPI Integer32
  ochanStatsVCI Integer32
  ochanStatsLostCells Counter32
  ochanStatsTransmittedCells Counter32
  ochanStatsIntentionalLostCells Counter32
  ochanStatsCLP0Cells Counter32
  ochanStatsLostPackets Counter32
  ochanStatsTransmittedPackets Counter32

LinkEntry  
SEQUENCE    
  linkSrc SpansAddress
  linkDest SpansAddress
  linkCapacity Integer32
  linkAge Integer32

SigPathEntry  
SEQUENCE    
  sigPathPort Integer32
  sigPathVPI Integer32
  sigPathVCI Integer32
  sigPathClsVCI Integer32
  sigPathAdminStatus INTEGER
  sigPathOperStatus INTEGER
  sigPathEntryStatus EntryStatus
  sigPathAALType INTEGER
  sigPathCDV Integer32
  sigPathPolicingAction INTEGER
  sigPathRemoteAtmAddress SpansAddress
  sigPathRemoteIpAddress IpAddress
  sigPathType INTEGER
  sigPathClsUpcContract Integer32
  sigPathSigReservedBW Integer32
  sigPathMinVCI Integer32
  sigPathMaxVCI Integer32
  sigPathOpenTimeout Integer32
  sigPathCloseTimeout Integer32
  sigPathOutputSigService INTEGER
  sigPathAALOperType INTEGER

SigPathStatsEntry  
SEQUENCE    
  sigPathStatsPort Integer32
  sigPathStatsVPI Integer32
  sigPathVCCs Gauge32
  sigPathRestarts Counter32
  sigPathCallsCompletions Counter32
  sigPathCallsFailures Counter32
  sigPathCallsRejections Counter32
  sigPathSpansTransmittedMessages Counter32
  sigPathSpansReceivedMessages Counter32
  sigPathClsTransmittedMessages Counter32
  sigPathClsReceivedMessages Counter32

SpvcSrcEntry  
SEQUENCE    
  spvcSrcSpvcId Integer32
  spvcSrcSwitchAddr SpansAddress
  spvcSrcDestSpvcId Integer32
  spvcSrcDestSwitchAddr SpansAddress
  spvcSrcInPort Integer32
  spvcSrcInVPI Integer32
  spvcSrcInVCI Integer32
  spvcSrcAllocBandwidth Gauge32
  spvcSrcUpTime TimeTicks
  spvcSrcStatus INTEGER
  spvcSrcEntryStatus EntryStatus

SpvcDestEntry  
SEQUENCE    
  spvcDestSpvcId Integer32
  spvcDestSwitchAddr SpansAddress
  spvcDestSrcSpvcId Integer32
  spvcDestSrcSwitchAddr SpansAddress
  spvcDestOutPort Integer32
  spvcDestOutVPI Integer32
  spvcDestOutVCI Integer32
  spvcDestAllocBandwidth Gauge32
  spvcDestUpTime TimeTicks
  spvcDestStatus INTEGER
  spvcDestEntryStatus EntryStatus

PnniSpvcSrcEntry  
SEQUENCE    
  pnniSpvcSrcIndex Integer32
  pnniSpvcSrcCallingPort Integer32
  pnniSpvcSrcCallingVPI Integer32
  pnniSpvcSrcCallingVCI Integer32
  pnniSpvcSrcCalledAtmAddr NsapAddr
  pnniSpvcSrcCalledPort Integer32
  pnniSpvcSrcCalledVPVCSel INTEGER
  pnniSpvcSrcCalledVPI Integer32
  pnniSpvcSrcCalledVCI Integer32
  pnniSpvcSrcCalledAssignedVPI Integer32
  pnniSpvcSrcCalledAssignedVCI Integer32
  pnniSpvcSrcFwdUpcKey Integer32
  pnniSpvcSrcBckUpcKey Integer32
  pnniSpvcSrcBearerClass INTEGER
  pnniSpvcSrcTrafficType INTEGER
  pnniSpvcSrcTimingReq INTEGER
  pnniSpvcSrcSusceptClip INTEGER
  pnniSpvcSrcFwdQoSClass INTEGER
  pnniSpvcSrcBckQoSClass INTEGER
  pnniSpvcSrcTransitNetSel TransitNetwork
  pnniSpvcSrcLastFailCause DisplayString
  pnniSpvcSrcRetryCount Integer32
  pnniSpvcSrcLastChangeTime TimeTicks
  pnniSpvcSrcStatus INTEGER
  pnniSpvcSrcName OCTET STRING
  pnniSpvcSrcEntryStatus EntryStatus
  pnniSpvcSrcRouteCost Integer32
  pnniSpvcSrcDtlIndex Integer32
  pnniSpvcSrcActiveDtlIndex Integer32
  pnniSpvcSrcRerouteStatus INTEGER
  pnniSpvcSrcCallingDomain Integer32
  pnniSpvcSrcQosIndex Integer32
  pnniSpvcSrcDtlIndex1 Integer32
  pnniSpvcSrcDtlIndex2 Integer32
  pnniSpvcSrcDtlIndex3 Integer32
  pnniSpvcSrcDtlIndex4 Integer32
  pnniSpvcSrcDtlWeight1 Integer32
  pnniSpvcSrcDtlWeight2 Integer32
  pnniSpvcSrcDtlWeight3 Integer32
  pnniSpvcSrcDtlWeight4 Integer32
  pnniSpvcSrcBackoffStatus INTEGER
  pnniSpvcSrcPriority Integer32
  pnniSpvcSrcLastLocation DisplayString
  pnniSpvcSrcOldRouteCost Integer32
  pnniSpvcSrcDownReason INTEGER
  pnniSpvcSrcActiveDtlNodeIndex Integer32
  pnniSpvcSrcDtlTag Integer32
  pnniSpvcSrcAutoDtlStatus INTEGER
  pnniSpvcSrcRGroupIndex INTEGER
  pnniSpvcSrcSecondaryVPI Integer32
  pnniSpvcSrcSecondaryVCI Integer32

PnniSpvcDestEntry  
SEQUENCE    
  pnniSpvcDestIndex Integer32
  pnniSpvcDestCallingAtmAddr NsapAddr
  pnniSpvcDestCallingPort Integer32
  pnniSpvcDestCallingVPI Integer32
  pnniSpvcDestCallingVCI Integer32
  pnniSpvcDestCalledAtmAddr NsapAddr
  pnniSpvcDestCalledPort Integer32
  pnniSpvcDestAssignedVPI Integer32
  pnniSpvcDestAssignedVCI Integer32
  pnniSpvcDestBearerClass INTEGER
  pnniSpvcDestTrafficType INTEGER
  pnniSpvcDestTimingReq INTEGER
  pnniSpvcDestSusceptClip INTEGER
  pnniSpvcDestUpTime TimeTicks
  pnniSpvcDestFwdQoSClass INTEGER
  pnniSpvcDestBckQoSClass INTEGER
  pnniSpvcDestTransitNetSel TransitNetwork
  pnniSpvcDestStatus INTEGER
  pnniSpvcDestRGroupIndex INTEGER

PnniSpvpcSrcEntry  
SEQUENCE    
  pnniSpvpcSrcIndex INTEGER
  pnniSpvpcSrcCallingPort INTEGER
  pnniSpvpcSrcCallingVPI Integer32
  pnniSpvpcSrcCalledAtmAddr NsapAddr
  pnniSpvpcSrcCalledPort Integer32
  pnniSpvpcSrcCalledVPVCSel INTEGER
  pnniSpvpcSrcCalledVPI INTEGER
  pnniSpvpcSrcCalledAssignedVPI INTEGER
  pnniSpvpcSrcFwdUpcKey INTEGER
  pnniSpvpcSrcBckUpcKey INTEGER
  pnniSpvpcSrcSusceptClip INTEGER
  pnniSpvpcSrcFwdQoSClass INTEGER
  pnniSpvpcSrcBckQoSClass INTEGER
  pnniSpvpcSrcLastFailCause DisplayString
  pnniSpvpcSrcRetryCount Integer32
  pnniSpvpcSrcLastChangeTime TimeTicks
  pnniSpvpcSrcStatus INTEGER
  pnniSpvpcSrcName OCTET STRING
  pnniSpvpcSrcRowStatus RowStatus
  pnniSpvpcSrcRouteCost Integer32
  pnniSpvpcSrcRerouteStatus INTEGER
  pnniSpvpcSrcCallingDomain Integer32
  pnniSpvpcSrcQosIndex Integer32
  pnniSpvpcSrcPriority Integer32
  pnniSpvpcSrcLastLocation DisplayString
  pnniSpvpcSrcOldRouteCost Integer32
  pnniSpvpcSrcDownReason INTEGER
  pnniSpvpcSrcBackoffStatus INTEGER
  pnniSpvpcSrcActiveDtlNodeIndex Integer32
  pnniSpvpcSrcActiveDtlIndex Integer32
  pnniSpvpcSrcDtlTag Integer32
  pnniSpvpcSrcAutoDtlStatus INTEGER
  pnniSpvpcSrcRGroupIndex INTEGER
  pnniSpvpcSrcSecondaryVPI Integer32

PnniSpvpcDestEntry  
SEQUENCE    
  pnniSpvpcDestIndex INTEGER
  pnniSpvpcDestCallingAtmAddr NsapAddr
  pnniSpvpcDestCallingPort INTEGER
  pnniSpvpcDestCallingVPI INTEGER
  pnniSpvpcDestCalledAtmAddr NsapAddr
  pnniSpvpcDestCalledPort INTEGER
  pnniSpvpcDestAssignedVPI INTEGER
  pnniSpvpcDestSusceptClip INTEGER
  pnniSpvpcDestUpTime TimeTicks
  pnniSpvpcDestFwdQoSClass INTEGER
  pnniSpvpcDestBckQoSClass INTEGER
  pnniSpvpcDestStatus INTEGER
  pnniSpvpcDestRGroupIndex INTEGER

PnniPmpSpvccSrcRootEntry  
SEQUENCE    
  pnniPmpSpvccSrcRootIndex Integer32
  pnniPmpSpvccSrcRootPort Integer32
  pnniPmpSpvccSrcRootVPI Integer32
  pnniPmpSpvccSrcRootVCI Integer32
  pnniPmpSpvccSrcRootFwdUpcKey Integer32
  pnniPmpSpvccSrcRootBearerClass INTEGER
  pnniPmpSpvccSrcRootSusceptClip INTEGER
  pnniPmpSpvccSrcRootFwdQoSClass INTEGER
  pnniPmpSpvccSrcRootStatus INTEGER
  pnniPmpSpvccSrcRootName OCTET STRING
  pnniPmpSpvccSrcRootPriority Integer32
  pnniPmpSpvccSrcRootNumberOfParties Integer32
  pnniPmpSpvccSrcRootNextPartyIndex TestAndIncr
  pnniPmpSpvccSrcRootCallingDomain Integer32
  pnniPmpSpvccSrcRootRowStatus RowStatus
  pnniPmpSpvccSrcRootRGroupIndex INTEGER
  pnniPmpSpvccSrcRootSecondaryVPI Integer32
  pnniPmpSpvccSrcRootSecondaryVCI Integer32

PnniPmpSpvccSrcPartyEntry  
SEQUENCE    
  pnniPmpSpvccSrcPartyIndex Integer32
  pnniPmpSpvccSrcPartyAtmAddr NsapAddr
  pnniPmpSpvccSrcPartyVPVCSel INTEGER
  pnniPmpSpvccSrcPartyVPI Integer32
  pnniPmpSpvccSrcPartyVCI Integer32
  pnniPmpSpvccSrcPartyAssignedVPI Integer32
  pnniPmpSpvccSrcPartyAssignedVCI Integer32
  pnniPmpSpvccSrcPartyStatus INTEGER
  pnniPmpSpvccSrcPartyName OCTET STRING
  pnniPmpSpvccSrcPartyLastFailCause DisplayString
  pnniPmpSpvccSrcPartyRetryCount Integer32
  pnniPmpSpvccSrcPartyLastChangeTime TimeTicks
  pnniPmpSpvccSrcPartyFtDtlIndex Integer32
  pnniPmpSpvccSrcPartyRerouteStatus INTEGER
  pnniPmpSpvccSrcPartyQosIndex Integer32
  pnniPmpSpvccSrcPartyRowStatus RowStatus
  pnniPmpSpvccSrcPartyLastLocation DisplayString
  pnniPmpSpvccSrcPartyAutoDtlStatus INTEGER
  pnniPmpSpvccSrcPartyDownReason INTEGER
  pnniPmpSpvccSrcPartyRouteCost Integer32

PnniPmpSpvccDestRootEntry  
SEQUENCE    
  pnniPmpSpvccDestRootIndex Integer32
  pnniPmpSpvccDestRootAtmAddr NsapAddr
  pnniPmpSpvccDestRootPort Integer32
  pnniPmpSpvccDestRootVPI Integer32
  pnniPmpSpvccDestRootVCI Integer32
  pnniPmpSpvccDestRootBearerClass INTEGER
  pnniPmpSpvccDestRootSusceptClip INTEGER
  pnniPmpSpvccDestRootFwdQoSClass INTEGER
  pnniPmpSpvccDestRootNumberOfParties Integer32

PnniPmpSpvccDestPartyEntry  
SEQUENCE    
  pnniPmpSpvccDestPartyIndex Integer32
  pnniPmpSpvccDestPartyAtmAddr NsapAddr
  pnniPmpSpvccDestPartyPort Integer32
  pnniPmpSpvccDestPartyAssignedVPI Integer32
  pnniPmpSpvccDestPartyAssignedVCI Integer32
  pnniPmpSpvccDestPartyUpTime TimeTicks
  pnniPmpSpvccDestPartyTransitNetSel TransitNetwork
  pnniPmpSpvccDestPartyStatus INTEGER
  pnniPmpSpvccDestPartyRGroupIndex INTEGER

PnniSpvxcRGroupEntry  
SEQUENCE    
  pnniSpvxcRGroupIndex INTEGER
  pnniSpvxcRGroupPrimaryPort Integer32
  pnniSpvxcRGroupSecondaryPort Integer32
  pnniSpvxcRGroupNsapAddr NsapAddr
  pnniSpvxcRGroupSwitchoverCmd INTEGER
  pnniSpvxcRGroupActivePort Integer32
  pnniSpvxcRGroupPacingNumber Integer32
  pnniSpvxcRGroupPacingInterval Integer32
  pnniSpvxcRGroupAutoPVCSwitchover INTEGER
  pnniSpvxcRGroupName OCTET STRING
  pnniSpvxcRGroupState INTEGER
  pnniSpvxcRGroupRowStatus RowStatus

Q2931AdminEntry  
SEQUENCE    
  q2931AdminPort Integer32
  q2931AdminVPI Integer32
  q2931AdminVCI Integer32
  q2931AdminStatus INTEGER
  q2931OperStatus INTEGER
  q2931SSCOPOperStatus INTEGER
  q2931ILMIAdminStatus INTEGER
  q2931ILMIOperStatus INTEGER
  q2931AdminAALType INTEGER
  q2931AdminUNISide INTEGER
  q2931AdminConfigType INTEGER
  q2931AdminOperType INTEGER
  q2931AdminEntryStatus EntryStatus
  q2931AdminRemoteIpAddress IpAddress
  q2931SigReservedBW Integer32
  q2931ILMIReservedBW Integer32
  q2931ILMIAdminVCI Integer32
  q2931AdminMinVCI Integer32
  q2931AdminMaxVCI Integer32
  q2931MinVCI Integer32
  q2931MaxVCI Integer32
  q2931UNIConfigVersion INTEGER
  q2931UNIOperVersion INTEGER
  q2931ILMIRegistration INTEGER
  q2931CallingPDefaultAddress NsapAddr
  q2931AdminUseNativeE164 INTEGER
  q2931AdminNativeE164Address E164Address
  q2931AdminE164AddressResolution INTEGER
  q2931AdminFtPnniOrigCost INTEGER
  q2931AdminFtPnniTermCost Integer32
  q2931AdminAVPresentation Integer32
  q2931AdminSigMode INTEGER
  q2931AdminSigAlloc INTEGER
  q2931PeerPort Integer32
  q2931InputSigContract Integer32
  q2931OutputSigService INTEGER
  q2931SSCOPNoRespTimer Integer32
  q2931AdminIncomingNSAPFilterIndex Integer32
  q2931AdminOutgoingNSAPFilterIndex Integer32
  q2931AdminIEFilter Integer32
  q2931SendCallProc INTEGER
  q2931VCIRangeStatus INTEGER
  q2931ClearOnCarrierLoss INTEGER
  q2931QosClassExpansionKey Integer32
  q2931AtmrConfDomainID Integer32
  q2931AtmrPnniNodeIndex Integer32
  q2931AdminOperSigMode INTEGER
  q2931AdminOperSigAlloc INTEGER
  q2931OutputSigUpc Integer32
  q2931AdminPlanType INTEGER
  q2931AdminMaxVPI INTEGER
  q2931MaxSvccVPI INTEGER
  q2931LastChangeTime TimeStamp
  q2931MaxSvpcVPI INTEGER
  q2931VpCapability INTEGER
  q2931NNIProto INTEGER
  q2931VpciGroupIndex INTEGER
  q2931ProxyDirGroupIndex INTEGER
  q2931AcceleratedClear INTEGER
  q2931OutputIlmiUpc Integer32
  q2931OutputRccUpc Integer32
  q2931SupplementaryServicesStatus INTEGER
  q2931CallingPAddressPresentation INTEGER
  q2931CallingPAddressRestriction INTEGER
  q2931ConnectedPAddressPresentation INTEGER
  q2931ConnectedPAddressRestriction INTEGER
  q2931ConnectedPDefaultAddress NsapAddr
  q2931SubaddressingAdminStatus INTEGER
  q2931UserUserSignallingAdminStatus INTEGER
  q2931PnniRccVci Integer32
  q2931AdminubrCalls INTEGER
  q2931AdmincbrCalls INTEGER
  q2931AdminabrCalls INTEGER
  q2931AdminrtvbrCalls INTEGER
  q2931AdminnrtvbrCalls INTEGER

Q2931StatsEntry  
SEQUENCE    
  q2931StatsPort Integer32
  q2931StatsVPI Integer32
  q2931VCCs Gauge32
  q2931Restarts Counter32
  q2931CallsCompletions Counter32
  q2931CallsFailures Counter32
  q2931CallsRejections Counter32
  q2931TransmittedMessages Counter32
  q2931ReceivedMessages Counter32

Q2931E164AddrResEntry  
SEQUENCE    
  q2931E164Port Integer32
  q2931E164VPI Integer32
  q2931E164Nsap NsapAddr
  q2931E164NsapMask Integer32
  q2931E164Address E164Address
  q2931E164AddrResStatus EntryStatus

Q2931NPCallEntry  
SEQUENCE    
  q2931NPCallIndex Integer32
  q2931NPCallDstNsap NsapAddr
  q2931NPCallState INTEGER
  q2931NPCallClientType INTEGER
  q2931NPCallFwdUpcKey Integer32
  q2931NPCallBckUpcKey Integer32
  q2931NPCallCallingDomain Integer32
  q2931NPCallQosIndex Integer32
  q2931NPCallQosClassFwd INTEGER
  q2931NPCallQosClassBwd INTEGER
  q2931NPCallBearerClass INTEGER
  q2931NPCallVerbose INTEGER
  q2931NPCallCauseCode Integer32
  q2931NPPingState INTEGER
  q2931NPPingPktCount Integer32
  q2931NPPingStatsPktsSent Integer32
  q2931NPPingStatsPktsReceived Integer32
  q2931NPPingStatsAverageDelay Integer32
  q2931NPPingStatsMinimumDelay Integer32
  q2931NPPingStatsMaximumDelay Integer32
  q2931NPMeasureRoundTripDelay INTEGER
  q2931NPCallStatus RowStatus

Q2931AFTemplateEntry  
SEQUENCE    
  q2931AFTemplateIndex Integer32
  q2931AFTemplateSrcPort Integer32
  q2931AFTemplateSrcVPI Integer32
  q2931AFTemplateSrcNsap NsapAddr
  q2931AFTemplateSrcNsapMask Integer32
  q2931AFTemplateDstPort Integer32
  q2931AFTemplateDstVPI Integer32
  q2931AFTemplateDstNsap NsapAddr
  q2931AFTemplateDstNsapMask Integer32
  q2931AFTemplateAction INTEGER
  q2931AFTemplateName OCTET STRING
  q2931AFTemplateStatus RowStatus

Q2931AFFilterEntry  
SEQUENCE    
  q2931AFFilterIndex Integer32
  q2931AFFilterName OCTET STRING
  q2931AFFilterStatus RowStatus

Q2931AFFilterTListEntry  
SEQUENCE    
  q2931AFFilterTListIndex Integer32
  q2931AFFilterTListTemplateIndex Integer32
  q2931AFFilterTListStatus RowStatus

Q2931AFStatsEntry  
SEQUENCE    
  q2931AFDirection INTEGER
  q2931AFAccepts Counter32
  q2931AFRejectKnowns Counter32
  q2931AFRejectUnknowns Counter32

Q2931AFLookupEntry  
SEQUENCE    
  q2931AFLookupIndex Integer32
  q2931AFLookupNSAPFilterIndex Integer32
  q2931AFLookupSrcPort Integer32
  q2931AFLookupSrcVPI Integer32
  q2931AFLookupSrcNsap NsapAddr
  q2931AFLookupDstPort Integer32
  q2931AFLookupDstVPI Integer32
  q2931AFLookupDstNsap NsapAddr
  q2931AFLookupResult INTEGER
  q2931AFLookupTemplate Integer32
  q2931AFLookupStatus RowStatus

ProxyDirMapEntry  
SEQUENCE    
  proxyDirMapIndex INTEGER
  proxyDirMapAESA OCTET STRING
  proxyDirMapGroup Integer32
  proxyDirMapVPCI Integer32
  proxyDirMapPort Integer32
  proxyDirMapVp Integer32
  proxyDirMapStatus RowStatus

ProxyDirGroup  
SEQUENCE    
  proxyDirGroupIndex INTEGER
  proxyDirGroupPrefix Integer32
  proxyDirGroupVPCIGroup Integer32
  proxyDirGroupStatus RowStatus

VmtVpciMapEntry  
SEQUENCE    
  vmtVpciMapIndex INTEGER
  vmtVpciMapVPCI Integer32
  vmtVpciMapVPI Integer32
  vmtVpciMapPort Integer32
  vmtVpciMapStatus RowStatus

VmtVpciMapGroupEntry  
SEQUENCE    
  vmtVpciMapGroupIndex INTEGER
  vmtVpciMapGroupStatus RowStatus

VmtVpciMapListEntry  
SEQUENCE    
  vmtVpciMapListIndex INTEGER
  vmtVpciMapListMEIndex Integer32
  vmtVpciMapListStatus RowStatus

PerCallDbgFilterEntry  
SEQUENCE    
  perCallDbgFilterIndex Integer32
  perCallDbgFilterTemplateId Integer32
  perCallDbgFilterName OCTET STRING
  perCallDbgFilterFlavor Integer32
  perCallDbgFilterMatches Counter32
  perCallDbgFilterRowStatus RowStatus

NsapNetworkPrefixEntry  
SEQUENCE    
  nsapNetworkPrefixPort Integer32
  nsapNetworkPrefixVPI Integer32
  nsapNetworkPrefixValue NsapPrefix
  nsapNetworkPrefixStatus EntryStatus

NsapTopologyEntry  
SEQUENCE    
  nsapTopoBoard Integer32
  nsapTopoLinkSrc NsapAddr
  nsapTopoLinkSrcMask Integer32
  nsapTopoLinkSrcPort Integer32
  nsapTopoLinkSrcVpi Integer32
  nsapTopoLinkDest NsapAddr
  nsapTopoLinkDestMask Integer32
  nsapTopoLinkDestPort Integer32
  nsapTopoLinkDestVpi Integer32
  nsapTopoLinkCost Integer32
  nsapTopoLinkUbrVCs Gauge32
  nsapTopoLinkCbrCapacity Integer32
  nsapTopoLinkCbrFifo Integer32
  nsapTopoLinkVbrCapacity Integer32
  nsapTopoLinkVbrFifo Integer32
  nsapTopoLinkOrig INTEGER
  nsapTopoLinkCapabilitySet Integer32
  nsapTopoLinkFreshness Integer32
  nsapTopoLinkUbrEstimatedBandwidth Integer32

NsapStaticRouteEntry  
SEQUENCE    
  nsapStaticRouteAddress NsapAddr
  nsapStaticRouteMask Integer32
  nsapStaticRoutePort Integer32
  nsapStaticRouteVPI Integer32
  nsapStaticRouteCost Integer32
  nsapStaticRouteMaxCbrCap Integer32
  nsapStaticRouteMaxVbrCap Integer32
  nsapStaticRouteAbrSupport INTEGER
  nsapStaticRouteEpdSupport INTEGER
  nsapStaticRouteStatus EntryStatus

FtPnniDTLEntry  
SEQUENCE    
  ftPnniDTLIndex Integer32
  ftPnniDTLEntryIndex Integer32
  ftPnniDTLNodePrefix NsapPrefix
  ftPnniDTLNodeMask INTEGER
  ftPnniDTLPort Integer32
  ftPnniDTLVPI Integer32
  ftPnniDTLStatus EntryStatus

FtPnniSummaryEntry  
SEQUENCE    
  ftPnniSummaryAddress Integer32
  ftPnniSummaryPrefixLength Integer32
  ftPnniSummaryType INTEGER
  ftPnniSummarySuppress INTEGER
  ftPnniSummaryState INTEGER
  ftPnniSummaryStatus EntryStatus

UpcContractEntry  
SEQUENCE    
  upcContractKey INTEGER
  upcContractEntryStatus EntryStatus
  upcContractPCR01 Integer32
  upcContractSCR01 Integer32
  upcContractMBS01 Integer32
  upcContractPCR0 Integer32
  upcContractSCR0 Integer32
  upcContractMBS0 Integer32
  upcContractCDVT Integer32
  upcContractTagReq Integer32
  upcContractAal5Epd Integer32
  upcContractName DisplayString
  upcContractDoGCRAPolicing INTEGER
  upcContractIsAAL5 INTEGER
  upcContractDoPacketDiscard INTEGER
  upcContractDoPPPolicing INTEGER
  upcContractDoUBRTagging INTEGER
  upcContractSchedMode AtmConnSchedMode
  upcContractUseAltCLPThreshold INTEGER
  upcContractMCR Integer32
  upcContractEstimatedUbrBandwidth Integer32
  upcContractAAL5CountingMode AAL5CountingMode
  upcContractServiceCategory Integer32
  upcContractPoliceScheme INTEGER
  upcContractPCR Integer32
  upcContractSCR Integer32
  upcContractMBS Integer32
  upcContractServiceSubCategory INTEGER
  upcContractCongestionBasedPeakBw Integer32
  upcContractBehaviorClassSelector Integer32

QosClassExpansionEntry  
SEQUENCE    
  qosClassExpansionKey Integer32
  qosClassValue INTEGER
  qosClassExpansionEntryStatus EntryStatus
  qosClassFwdCtd INTEGER
  qosClassFwdCdv INTEGER
  qosClassBackCdv INTEGER
  qosClassFwdClr INTEGER
  qosClassBackClr INTEGER
  qosClassName DisplayString

PathExtQosMetricEntry  
SEQUENCE    
  pathExtQosMetricIndex Integer32
  pathExtQosMetricMaxCtd Integer32
  pathExtQosMetricMaxCdv Integer32
  pathExtQosMetricMaxClr Integer32
  pathExtQosMetricEntryStatus EntryStatus

PathExtEntry  
SEQUENCE    
  pathExtCbrMetric Integer32
  pathExtRtVbrMetric Integer32
  pathExtNrtVbrMetric Integer32
  pathExtAbrMetric Integer32
  pathExtUbrMetric Integer32
  pathExtEntryStatus EntryStatus

OutputPathExtEntry  
SEQUENCE    
  opathExtCbrMetric Integer32
  opathExtRtVbrMetric Integer32
  opathExtNrtVbrMetric Integer32
  opathExtAbrMetric Integer32
  opathExtUbrMetric Integer32
  opathExtEntryStatus EntryStatus

VpGroupEntry  
SEQUENCE    
  vpGroupIndex Integer32
  vpGroupPort Integer32
  vpGroupVPI Integer32
  vpGroupVPCI Integer32
  vpGroupEntryStatus EntryStatus

SwBoardEntry  
SEQUENCE    
  swBoardIndex Integer32
  swBoardMaxPaths Integer32
  swBoardMaxChannels Integer32
  swBoardAtmAddress SpansAddress
  swBoardUptime TimeTicks
  swBoardCDV Integer32
  swBoardPolicingAction INTEGER
  swBoardNsapPrefix NsapPrefix
  swBoardClockScalingFactor Integer32
  swBoardDebugMode INTEGER
  swBoardMulticastMode INTEGER
  swBoardFingerMode INTEGER
  swBoardATMLayerOAM INTEGER

SwBoardTopoEntry  
SEQUENCE    
  swBoardTopoIndex Integer32
  swBoardTopoNumberOfLinks Integer32

SwBoardLinkEntry  
SEQUENCE    
  swBoardLinkIndex Integer32
  swBoardLinkSrc SpansAddress
  swBoardLinkDest SpansAddress
  swBoardLinkCapacity Integer32
  swBoardLinkAge Integer32

OamGeneratingChannelEntry  
SEQUENCE    
  oamGeneratingChannelCells Counter32

OamGeneratingOpathEntry  
SEQUENCE    
  oamGeneratingOpathCells Counter32

OamGeneratingPathrEntry  
SEQUENCE    
  oamGeneratingPathrCells Counter32

OamReceivedPathEntry  
SEQUENCE    
  oamReceivedPathAISCells Counter32
  oamReceivedPathRDICells Counter32

GuardEntry  
SEQUENCE    
  oamGuard TimeStamp

TrapDestEntry  
SEQUENCE    
  trapDest IpAddress
  trapDestStatus EntryStatus

SnmpAgentEntry  
SEQUENCE    
  snmpAgentBoardNumber Integer32
  snmpAgentInterface Integer32
  snmpAgentAddress IpAddress

SyslogDestinationEntry  
SEQUENCE    
  syslogDestinationHost IpAddress
  syslogDestinationStatus RowStatus

Defined Values

foreSwitchModule 1.3.6.1.4.1.326.2.7
Fore Switch MIB
MODULE-IDENTITY    

boardGroup 1.3.6.1.4.1.326.2.2.1.1.1
OBJECT IDENTIFIER    

moduleGroup 1.3.6.1.4.1.326.2.2.1.1.2
OBJECT IDENTIFIER    

timing 1.3.6.1.4.1.326.2.2.1.3
OBJECT IDENTIFIER    

netmodTimingGroup 1.3.6.1.4.1.326.2.2.1.3.1
OBJECT IDENTIFIER    

boardTimingGroup 1.3.6.1.4.1.326.2.2.1.3.2
OBJECT IDENTIFIER    

environment 1.3.6.1.4.1.326.2.2.1.4
OBJECT IDENTIFIER    

alarmGroup 1.3.6.1.4.1.326.2.2.1.4.1
OBJECT IDENTIFIER    

powerGroup 1.3.6.1.4.1.326.2.2.1.4.2
OBJECT IDENTIFIER    

fansGroup 1.3.6.1.4.1.326.2.2.1.4.3
OBJECT IDENTIFIER    

tempGroup 1.3.6.1.4.1.326.2.2.1.4.4
OBJECT IDENTIFIER    

cpuGroup 1.3.6.1.4.1.326.2.2.1.4.5
OBJECT IDENTIFIER    

mgmtGroup 1.3.6.1.4.1.326.2.2.1.4.6
OBJECT IDENTIFIER    

fabricGroup 1.3.6.1.4.1.326.2.2.1.4.7
OBJECT IDENTIFIER    

shmem 1.3.6.1.4.1.326.2.2.1.5
OBJECT IDENTIFIER    

netmodShmemGroup 1.3.6.1.4.1.326.2.2.1.5.1
OBJECT IDENTIFIER    

portShmemGroup 1.3.6.1.4.1.326.2.2.1.5.2
OBJECT IDENTIFIER    

netmodShmem2Group 1.3.6.1.4.1.326.2.2.1.5.3
OBJECT IDENTIFIER    

portShmem2Group 1.3.6.1.4.1.326.2.2.1.5.4
OBJECT IDENTIFIER    

connShmem2Group 1.3.6.1.4.1.326.2.2.1.5.5
OBJECT IDENTIFIER    

netmodShmem3Group 1.3.6.1.4.1.326.2.2.1.5.6
OBJECT IDENTIFIER    

portShmem3Group 1.3.6.1.4.1.326.2.2.1.5.7
OBJECT IDENTIFIER    

connShmem3Group 1.3.6.1.4.1.326.2.2.1.5.8
OBJECT IDENTIFIER    

netmodGenericShmemGroup 1.3.6.1.4.1.326.2.2.1.5.9
OBJECT IDENTIFIER    

genericOutputPortGroup 1.3.6.1.4.1.326.2.2.1.5.10
OBJECT IDENTIFIER    

dualScp 1.3.6.1.4.1.326.2.2.1.6
OBJECT IDENTIFIER    

dualScpGroup 1.3.6.1.4.1.326.2.2.1.6.1
OBJECT IDENTIFIER    

etherChipSet 1.3.6.1.4.1.326.2.2.1.10
OBJECT IDENTIFIER    

etherChipSetDec 1.3.6.1.4.1.326.2.2.1.10.1
OBJECT IDENTIFIER    

etherChipSetDec21440 1.3.6.1.4.1.326.2.2.1.10.1.1
OBJECT IDENTIFIER    

switchGroup 1.3.6.1.4.1.326.2.2.2.1.1
OBJECT IDENTIFIER    

portGroup 1.3.6.1.4.1.326.2.2.2.1.2
OBJECT IDENTIFIER    

pathGroup 1.3.6.1.4.1.326.2.2.2.1.3
OBJECT IDENTIFIER    

channelGroup 1.3.6.1.4.1.326.2.2.2.1.4
OBJECT IDENTIFIER    

topologyGroup 1.3.6.1.4.1.326.2.2.2.1.5
OBJECT IDENTIFIER    

signalingGroup 1.3.6.1.4.1.326.2.2.2.1.6
OBJECT IDENTIFIER    

spansGroup 1.3.6.1.4.1.326.2.2.2.1.6.1
OBJECT IDENTIFIER    

q2931Group 1.3.6.1.4.1.326.2.2.2.1.6.2
OBJECT IDENTIFIER    

q2931LayerGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.1
OBJECT IDENTIFIER    

swBoardGroup 1.3.6.1.4.1.326.2.2.2.1.7
OBJECT IDENTIFIER    

swBoardTopologyGroup 1.3.6.1.4.1.326.2.2.2.1.8
OBJECT IDENTIFIER    

nsapGroup 1.3.6.1.4.1.326.2.2.2.1.9
OBJECT IDENTIFIER    

upcContractGroup 1.3.6.1.4.1.326.2.2.2.1.10
OBJECT IDENTIFIER    

confTopologyGroup 1.3.6.1.4.1.326.2.2.2.1.11
OBJECT IDENTIFIER    

oamGroup 1.3.6.1.4.1.326.2.2.2.1.12
OBJECT IDENTIFIER    

guardGroup 1.3.6.1.4.1.326.2.2.2.1.13
OBJECT IDENTIFIER    

ifIndexMapGroup 1.3.6.1.4.1.326.2.2.2.1.14
OBJECT IDENTIFIER    

ifIndexNameGroup 1.3.6.1.4.1.326.2.2.2.1.15
OBJECT IDENTIFIER    

cesExtGroup 1.3.6.1.4.1.326.2.2.2.1.16
OBJECT IDENTIFIER    

qosClassExpansionGroup 1.3.6.1.4.1.326.2.2.2.1.17
OBJECT IDENTIFIER    

pathExtGroup 1.3.6.1.4.1.326.2.2.2.1.18
OBJECT IDENTIFIER    

poolGroup 1.3.6.1.4.1.326.2.2.2.1.19
OBJECT IDENTIFIER    

asxAtmIfGroup 1.3.6.1.4.1.326.2.2.2.1.20
OBJECT IDENTIFIER    

syncStatusMsgGroup 1.3.6.1.4.1.326.2.2.2.1.21
OBJECT IDENTIFIER    

syslogGroup 1.3.6.1.4.1.326.2.2.2.1.22
OBJECT IDENTIFIER    

poolConfGroup 1.3.6.1.4.1.326.2.2.2.1.19.1
OBJECT IDENTIFIER    

snmp 1.3.6.1.4.1.326.2.2.2.2
OBJECT IDENTIFIER    

trapConfGroup 1.3.6.1.4.1.326.2.2.2.2.1
OBJECT IDENTIFIER    

snmpConfGroup 1.3.6.1.4.1.326.2.2.2.2.2
OBJECT IDENTIFIER    

snmpAgentAddressGroup 1.3.6.1.4.1.326.2.2.2.2.5
OBJECT IDENTIFIER    

boardTable 1.3.6.1.4.1.326.2.2.1.1.1.1
A table of ATM switch board information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BoardEntry

boardEntry 1.3.6.1.4.1.326.2.2.1.1.1.1.1
A table entry containing ATM switch board information.
Status: current Access: not-accessible
OBJECT-TYPE    
  BoardEntry  

boardIndex 1.3.6.1.4.1.326.2.2.1.1.1.1.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

boardVersion 1.3.6.1.4.1.326.2.2.1.1.1.1.1.2
The ATM switch board version number in hex. The version number 0x1 is revision A, 0x2 is revision B etc. Version number 0x0 represents an unknown type.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

boardModel 1.3.6.1.4.1.326.2.2.1.1.1.1.1.3
The ATM switch board model number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), asx100(1), asx200(2), asx200wg(4), asx200bx(5), asx200bxe(6), cabletron9A000(7), asx1000(8), le155(9), sfcs200wg(10), sfcs200bx(11), sfcs1000(12), tnx210(15), tnx1100(16), asx1200(17), asx4000(18), le25(19), esx3000(20), tnx1100b(21), asx150(22)  

boardSerialNumber 1.3.6.1.4.1.326.2.2.1.1.1.1.1.4
The ATM switch board serial number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

numberOfModules 1.3.6.1.4.1.326.2.2.1.1.1.1.1.5
The number of network modules on this ATM switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vpiLookupErrors 1.3.6.1.4.1.326.2.2.1.1.1.1.1.6
The number of VPI lookup errors.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

vciLookupErrors 1.3.6.1.4.1.326.2.2.1.1.1.1.1.7
The number of VCI lookup errors.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

boardControlPort 1.3.6.1.4.1.326.2.2.1.1.1.1.1.8
This object identifies the index for the control port on this switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

boardHDCOMPAsicVersion 1.3.6.1.4.1.326.2.2.1.1.1.1.1.9
This object identifies the version number of the HDCOMP ASIC on this switch board.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32  

boardMcastSpaceIndex 1.3.6.1.4.1.326.2.2.1.1.1.1.1.10
This object is the index into mcastSpaceTable that gives the number of multicast connections currently supported on this board. Changing this value has the effect of changing the number of multicast connections supported. Change will be effective after reboot only.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

numberOfBoards 1.3.6.1.4.1.326.2.2.1.1.1.2
The number of switch boards on this ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

utilization 1.3.6.1.4.1.326.2.2.1.1.1.3
OBJECT IDENTIFIER    

procUtilGroup 1.3.6.1.4.1.326.2.2.1.1.1.3.1
OBJECT IDENTIFIER    

mbufUtilGroup 1.3.6.1.4.1.326.2.2.1.1.1.3.3
OBJECT IDENTIFIER    

procUtilLastUpdate 1.3.6.1.4.1.326.2.2.1.1.1.3.1.1
The time the procUtilValue was last updated
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

procUtilValue 1.3.6.1.4.1.326.2.2.1.1.1.3.1.2
The percentage of the processor power that has been used over the last monitoring interval
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..100  

procUtilMonInterval 1.3.6.1.4.1.326.2.2.1.1.1.3.1.3
The amount of time between calculations of the procUtilValue. This value is expressed in units of 10 msec, (100 per sec). This value may take the value of 1 to 60 seconds
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 100..6000  

procUtilMinLoad 1.3.6.1.4.1.326.2.2.1.1.1.3.1.4
The MIN percentage of the processor power that has been. This value can be reset by setting the field procUtilHistoryReset.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..100  

procUtilMinLoadLastUpdate 1.3.6.1.4.1.326.2.2.1.1.1.3.1.5
The time the procUtilMinLoad was last updated
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

procUtilMaxLoad 1.3.6.1.4.1.326.2.2.1.1.1.3.1.6
The MAX percentage of the processor power that has been. This value can be reset by setting the field procUtilHistoryReset.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..100  

procUtilMaxLoadLastUpdate 1.3.6.1.4.1.326.2.2.1.1.1.3.1.7
The time the procUtilMaxLoad was last updated
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

procUtilHistoryReset 1.3.6.1.4.1.326.2.2.1.1.1.3.1.8
This is in effect a WRITE_ONLY field. Setting this field resets the procUtilMinLoad, procUtilMinLoadLastUpdate, procUtilMaxLoad, and procUtilMaxLoadLastUpdate. This field can be set to anything by the NMS. When this field is read, it will always report NULL.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0  

procUtilsNumMallocPart 1.3.6.1.4.1.326.2.2.1.1.1.3.1.9
The number of malloc partitions used on this SCP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

procUtilsSystemPartitionID 1.3.6.1.4.1.326.2.2.1.1.1.3.1.10
The partition ID os the system MALLOC pool. Use this value as an ID into the mallocUtilTable to view the system malloc pool statistics
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

boardStatsTable 1.3.6.1.4.1.326.2.2.1.1.1.4
A table of ATM switch fabric statistics information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BoardStatsEntry

boardStatsEntry 1.3.6.1.4.1.326.2.2.1.1.1.4.1
A table entry containing ATM switch fabric statistics information.
Status: current Access: not-accessible
OBJECT-TYPE    
  BoardStatsEntry  

boardStatsBoard 1.3.6.1.4.1.326.2.2.1.1.1.4.1.1
The index of this fabric within the ATM switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

boardStatsIndex 1.3.6.1.4.1.326.2.2.1.1.1.4.1.2
The index of this statistics within the ATM switch fabric.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

boardStatsName 1.3.6.1.4.1.326.2.2.1.1.1.4.1.3
The name of this statistics within the ATM switch fabric.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

boardStatsValue 1.3.6.1.4.1.326.2.2.1.1.1.4.1.4
The value of this statistics within the ATM switch fabric.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

portCardGroup 1.3.6.1.4.1.326.2.2.1.1.1.5
OBJECT IDENTIFIER    

portCardTable 1.3.6.1.4.1.326.2.2.1.1.1.5.1
A table of ATM switch port card information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortCardEntry

portCardEntry 1.3.6.1.4.1.326.2.2.1.1.1.5.1.1
A table entry containing ATM switch port card information.
Status: current Access: not-accessible
OBJECT-TYPE    
  PortCardEntry  

portCardIndex 1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.1
The unique index of this port card within the ATM switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

portCardName 1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.2
The name of this port card.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

portCardFlavor 1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.3
The flavor of this port card.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

portCardType 1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.4
The type description of this port card.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

portCardUptime 1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.5
The length of time this port card has been up in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

portCardSerialNumber 1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.6
The serial number of this port card.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

portCardAssemblyRevision 1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.7
The assembly revision number of this port card.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portCardHardwareConf 1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.8
The hardware configuration number of this port card.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portCardState 1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.9
The desired state of this port card. If set to reset(1), the port card is reset. Normally, when the port card is active, it is inService(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), inService(2), outOfService(3)  

boardTrafficManagementGroup 1.3.6.1.4.1.326.2.2.1.1.1.6
OBJECT IDENTIFIER    

boardTrafficManagementPerPriorityTable 1.3.6.1.4.1.326.2.2.1.1.1.6.1
A table of ATM switch fabric traffic management features that can be controlled per fabric and per priority.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BoardTrafficManagementPerPriorityEntry

boardTrafficManagementPerPriorityEntry 1.3.6.1.4.1.326.2.2.1.1.1.6.1.1
A table entry of ATM switch fabric traffic management features that can be controlled per fabric and per priority.
Status: current Access: not-accessible
OBJECT-TYPE    
  BoardTrafficManagementPerPriorityEntry  

btmPerPriorityBoard 1.3.6.1.4.1.326.2.2.1.1.1.6.1.1.1
The index of the fabric.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

btmPerPriorityPriority 1.3.6.1.4.1.326.2.2.1.1.1.6.1.1.2
The index of the traffic priority.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

btmPerPriorityFeature 1.3.6.1.4.1.326.2.2.1.1.1.6.1.1.3
The index of the feature. Feature 1 is EPD Threshold.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

btmPerPriorityPriorityName 1.3.6.1.4.1.326.2.2.1.1.1.6.1.1.4
The name of the traffic priority (e.g. CBR or UBR).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

btmPerPriorityValue 1.3.6.1.4.1.326.2.2.1.1.1.6.1.1.5
The value of the specified feature for the specified priority.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

mallocUtilTable 1.3.6.1.4.1.326.2.2.1.1.1.3.2
A table containing malloc statistics for each memory partition
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MallocUtilEntry

mallocUtilEntry 1.3.6.1.4.1.326.2.2.1.1.1.3.2.1
A table containing malloc statistics for each memory partition
Status: current Access: not-accessible
OBJECT-TYPE    
  MallocUtilEntry  

mallocPartId 1.3.6.1.4.1.326.2.2.1.1.1.3.2.1.1
The partition number for this malloc partition. The switch has a default partition named (procUtilsSystemPartitionID).
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

numBytesFree 1.3.6.1.4.1.326.2.2.1.1.1.3.2.1.2
Number of Free Bytes in this partition
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

numBlocksFree 1.3.6.1.4.1.326.2.2.1.1.1.3.2.1.3
The number of free blocks in this partition
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

maxBlockSizeFree 1.3.6.1.4.1.326.2.2.1.1.1.3.2.1.4
The max block size that is free
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

numBytesAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.2.1.5
Number of allocated bytes in this partition
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

numBlocksAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.2.1.6
The number of allocated blocks in this partiton
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsCount 1.3.6.1.4.1.326.2.2.1.1.1.3.3.1
mbufs obtained from page pool
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsClusters 1.3.6.1.4.1.326.2.2.1.1.1.3.3.2
clusters obtained from page pool
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsSpace 1.3.6.1.4.1.326.2.2.1.1.1.3.3.3
interface pages obtained from page pool
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsClFree 1.3.6.1.4.1.326.2.2.1.1.1.3.3.4
Free Clusters
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsDrops 1.3.6.1.4.1.326.2.2.1.1.1.3.3.5
Times failed to find space
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsWait 1.3.6.1.4.1.326.2.2.1.1.1.3.3.6
Times waited for space
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsDrain 1.3.6.1.4.1.326.2.2.1.1.1.3.3.7
Times drained protocols for space
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsFreeAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.3.8
# of mbufs allocated to free list
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsDataFreeAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.3.9
# of mbufs allocated to dynamic (data) allocation
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsHeaderAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.3.10
# of mbufs allocated to packet headers
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsSocketAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.3.11
# of mbufs allocated to socket structures
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsPcbAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.3.12
# of mbufs allocated to protocol control blocks
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsRtableAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.3.13
# of mbufs allocated to routing tables
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsHtableAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.3.14
# of mbufs allocated to IMP Host Tables
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsAtableAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.3.15
# of mbufs allocated to Address Resolution Tables
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsSoNameAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.3.16
# of mbufs allocated to Socket Name
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsZombieAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.3.17
# of mbufs allocated to Zombie Processes
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsSoOptsAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.3.18
# of mbufs allocated to Socket Options
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsFtableAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.3.19
# of mbufs allocated to Fragment Re-assembly Headers
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsRightsAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.3.20
# of mbufs allocated to Access Rights
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mbufsIFaddrAlloc 1.3.6.1.4.1.326.2.2.1.1.1.3.3.21
# of mbufs allocated to Interface Addresses
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

moduleTable 1.3.6.1.4.1.326.2.2.1.1.2.1
A table of network module information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ModuleEntry

moduleEntry 1.3.6.1.4.1.326.2.2.1.1.2.1.1
A table entry containing network module information.
Status: current Access: not-accessible
OBJECT-TYPE    
  ModuleEntry  

moduleBoard 1.3.6.1.4.1.326.2.2.1.1.2.1.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

moduleNumber 1.3.6.1.4.1.326.2.2.1.1.2.1.1.2
The number of this network module within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

moduleName 1.3.6.1.4.1.326.2.2.1.1.2.1.1.3
The type name of this network module within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

moduleSpeed 1.3.6.1.4.1.326.2.2.1.1.2.1.1.4
The speed of this network module within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

moduleNumberOfPorts 1.3.6.1.4.1.326.2.2.1.1.2.1.1.5
The number of ports on this network module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

moduleUptime 1.3.6.1.4.1.326.2.2.1.1.2.1.1.6
The length of time this network module has been up, in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

moduleHwMajorRev 1.3.6.1.4.1.326.2.2.1.1.2.1.1.7
The hardware major revision number of the network module. For generationD network modules this revision number is an ascii character value.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

moduleHwMinorRev 1.3.6.1.4.1.326.2.2.1.1.2.1.1.8
The hardware minor revision number of the network module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

moduleVersion 1.3.6.1.4.1.326.2.2.1.1.2.1.1.9
The hardware version of this network module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER generationA(1), generationB(2), generationC(3), generationLC(4), generationLE(5), generationD(6), generationPC1(7), generationPC2(8), generationE(10), generationPCF1(11), generationC2(67)  

moduleTimingSupport 1.3.6.1.4.1.326.2.2.1.1.2.1.1.10
Does this network module support distributed timing?
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

moduleProductNumber 1.3.6.1.4.1.326.2.2.1.1.2.1.1.11
The product number of this network module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

moduleState 1.3.6.1.4.1.326.2.2.1.1.2.1.1.12
The desired state of this network module. If set to reset(1), the netmod is reset. Normally, when the netmod is active, it is inService(2). To put a netmod out of service, this entry must be set to outOfService(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), inService(2), outOfService(3), resetPair(4)  

moduleSerialNumber 1.3.6.1.4.1.326.2.2.1.1.2.1.1.13
The string representing the serial number for this network module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

moduleTestAdminStatus 1.3.6.1.4.1.326.2.2.1.1.2.1.1.14
This variable indicates the hardware test configuration of the network module. It can be set to startTest(2), which starts the hardware tests on the network module. abortTest(3) aborts the test, if the network module is under test. The network module returns to normal(0) after the test ends or is aborted.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), startTest(2), abortTest(3)  

moduleTestOperStatus 1.3.6.1.4.1.326.2.2.1.1.2.1.1.15
The status of the hardware tests on the network module. normal (1) indicates that the network module has never undergone hardware tests. The network module is underTest (2), after the test is started on it, and goes to testSuccessful (3) or testFailed (4), after the tests end. If the tests are aborted, the network module goes to testAborted (5) state. Those network modules that do not support hardware tests like Series-C and LC modules, are in testUnsupported (6) state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), underTest(2), testSuccessful(3), testFailed(4), testAborted(5), testUnsupported(6)  

moduleTestStatusText 1.3.6.1.4.1.326.2.2.1.1.2.1.1.16
A message describing the status of the current test
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

moduleAttachState 1.3.6.1.4.1.326.2.2.1.1.2.1.1.17
The actual state of this network module. The netmod state is directed by the moduleState variable. This variable gives the actual state at a given time (which may lag behind the moduleState by several seconds).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inService(1), outOfService(2)  

moduleCLEI 1.3.6.1.4.1.326.2.2.1.1.2.1.1.18
The Common Language Equipment identifications (CLEI) of this network module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

appModuleTable 1.3.6.1.4.1.326.2.2.1.1.2.6
A table consisting of hardware components that have on-board CPUs. Currently, the FR/ATM, FUNI and IMA network modules appear in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AppModuleEntry

appModuleEntry 1.3.6.1.4.1.326.2.2.1.1.2.6.1
A table entry containing application module information.
Status: current Access: not-accessible
OBJECT-TYPE    
  AppModuleEntry  

appModuleIndex 1.3.6.1.4.1.326.2.2.1.1.2.6.1.1
The index of the application module in this switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

appModuleName 1.3.6.1.4.1.326.2.2.1.1.2.6.1.2
The name of this application module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

appModuleOperState 1.3.6.1.4.1.326.2.2.1.1.2.6.1.3
The operational state of this network module's hardware.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notConfigured(1), hwInitInProgress(2), up(3), shutDownInProgress(4), down(5), failed(6)  

appModuleStatusText 1.3.6.1.4.1.326.2.2.1.1.2.6.1.4
A text string describing the current state of the hardware.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

appModuleApplicationType 1.3.6.1.4.1.326.2.2.1.1.2.6.1.5
This variable indicates the application(s) running on this application module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

appModuleSoftwareVersion 1.3.6.1.4.1.326.2.2.1.1.2.6.1.6
Version of the software running on this application module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

appModuleBootSoftwareVersion 1.3.6.1.4.1.326.2.2.1.1.2.6.1.7
Version of the BOOT PROM software on this application module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

appModuleOosLed 1.3.6.1.4.1.326.2.2.1.1.2.6.1.8
The color of the OOS LED on the application module. This LED is off (1) when the network module is up and running and red (2) when the network module is down (administratively placed out of service or operationally down temporarily). For example, when the network module's hardware initialization is in progress, the LED will be red until the hardware initialization is complete.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER off(1), red(2)  

appModulePanicAction 1.3.6.1.4.1.326.2.2.1.1.2.6.1.9
This variable indicates the action to be taken if the on-board CPU fails. This module will be reset if this variable is set to reset(1) and will be suspended if this variable is set to suspend(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), suspend(2)  

outputBufferTable 1.3.6.1.4.1.326.2.2.1.1.2.2
A table of output buffer information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OutputBufferEntry

outputBufferEntry 1.3.6.1.4.1.326.2.2.1.1.2.2.1
A table entry containing output buffer information.
Status: current Access: not-accessible
OBJECT-TYPE    
  OutputBufferEntry  

obufBoard 1.3.6.1.4.1.326.2.2.1.1.2.2.1.1
The index of this output buffer's switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

obufNumber 1.3.6.1.4.1.326.2.2.1.1.2.2.1.2
The number of the network module for this output buffer.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

obufType 1.3.6.1.4.1.326.2.2.1.1.2.2.1.3
The Priority of this output buffer- 0 is lowest priority
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

obufOperStatus 1.3.6.1.4.1.326.2.2.1.1.2.2.1.4
The operational status of this output buffer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), enabled(2), disabled(3)  

obufBufferSize 1.3.6.1.4.1.326.2.2.1.1.2.2.1.5
The logical size of this output buffer, in cells.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

obufQueueLength 1.3.6.1.4.1.326.2.2.1.1.2.2.1.6
The number of cells in this output buffer.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

obufOverflows 1.3.6.1.4.1.326.2.2.1.1.2.2.1.7
The number of cells dropped because this output buffer was full.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

obufPriorityName 1.3.6.1.4.1.326.2.2.1.1.2.2.1.8
The priority name (eg. CBR, VBR) for this buffer.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

obufName 1.3.6.1.4.1.326.2.2.1.1.2.2.1.9
The name (eg. 1, 1A) of this buffer.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

hwPortTable 1.3.6.1.4.1.326.2.2.1.1.2.3
A table of hardware port information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwPortEntry

hwPortEntry 1.3.6.1.4.1.326.2.2.1.1.2.3.1
A table entry containing hardware port information.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwPortEntry  

hwPortBoard 1.3.6.1.4.1.326.2.2.1.1.2.3.1.1
The switch board index of this port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwPortModule 1.3.6.1.4.1.326.2.2.1.1.2.3.1.2
The network module number of this port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwPortNumber 1.3.6.1.4.1.326.2.2.1.1.2.3.1.3
The number of this port within its network module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwPortVersion 1.3.6.1.4.1.326.2.2.1.1.2.3.1.4
The generation of this network module. In general, generation A indicates the most original FORE Systems netmods. Generation-B are intermediate DS3/E3/TAXI. Generation-C are shared-memory based netmods.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER generationA(1), generationB(2), generationC(3), generationLC(4), generationLE(5), generationD(6), generationPC1(7), generationPC2(8), generationE(10), generationPCF1(11), generationC2(67)  

hwPortModel 1.3.6.1.4.1.326.2.2.1.1.2.3.1.5
The type of physical connection of this port. The model-ASX(7) indicates this is the control port of the switch. NOTE: as of 2/8/95 the elements model-6port-TAXI-100(6) and model-DS3-PDH(16) should no longer be used. Use the basic types model-TAXI-100(1) and model-DS3(3) to indicate these.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER model-TAXI-100(1), model-TAXI-140(2), model-DS3(3), model-OC3(4), model-8B10B(5), model-6port-TAXI-100(6), model-ASX-CTL(7), model-OC12(8), model-OC48(9), model-DS3-PDH(16), model-E3(17), model-J2(18), model-DS1(19), model-E1(20), model-TP25(21), model-ASX-BP(22), model-CESDS1(23), model-CESE1(24), model-FRAMDS1(25), model-FRAME1(26), model-IMADS1(27), model-IMAE1(28), model-RJ-45(29), model-CHOC12(30), model-STM1(31), model-OC3-POS(32), model-OC12-POS(33), model-CHOC3(34), model-ETH(35)  

hwPortOperStatus 1.3.6.1.4.1.326.2.2.1.1.2.3.1.6
The operational status of this port. If a port was administered up (by hwPortAdminStatus), but the carrier or the framing bits were lost, the hwPortOperStatus indicates that the port is down(3). Otherwise, the hwPortOperStatus is up(2).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), up(2), down(3), unused(4)  

hwPortBufferSize 1.3.6.1.4.1.326.2.2.1.1.2.3.1.7
The logical size of this port's output buffer, in cells.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

hwPortQueueLength 1.3.6.1.4.1.326.2.2.1.1.2.3.1.8
The number of cells in this port's output buffer.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Gauge32  

hwPortOverflows 1.3.6.1.4.1.326.2.2.1.1.2.3.1.9
The number of seconds in which cells were dropped because this port's output buffer was full.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

hwPortErrors 1.3.6.1.4.1.326.2.2.1.1.2.3.1.10
The number of seconds in which errored cells were dropped by this port.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter32  

hwPortCarrier 1.3.6.1.4.1.326.2.2.1.1.2.3.1.11
The presence or absence of carrier at this port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER carrier(1), noCarrier(2)  

hwPortGlobalIndex 1.3.6.1.4.1.326.2.2.1.1.2.3.1.12
The global index of this port within the ATM switch as a whole. It corresponds to the port number used in the software group of this MIB.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

hwPortName 1.3.6.1.4.1.326.2.2.1.1.2.3.1.13
A textual description of the port indicating the Board Network module and Port (BNP) identifiers. The module is indicated by a letter (A-D), while the board and the port are indicated by numbers.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..5)  

hwPortAdminStatus 1.3.6.1.4.1.326.2.2.1.1.2.3.1.14
The administrative state of the physical layer of this port. When a port is configured up(1), the physical layer is configured to process all physical layer events including the transmission and reception of data (cells). When a port is configured down(2), the physical layer should be shut down and should ignore all physical layer events (e.g. cell reception, carrier loss, loss of framing, parity errors, etc.). The operational status of a port is reflected in the hwPortOperStatus object.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

hwPortTAXILoopback 1.3.6.1.4.1.326.2.2.1.1.2.3.1.15
This variable represents the loopback status of a TAXI port. For non-TAXI ports (e.g. DS3/E3 or SONET) the loopback configuration should be set in their specific tables.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noLoopback(1), loopback(2)  

hwPortLEDModel 1.3.6.1.4.1.326.2.2.1.1.2.3.1.16
The LED model to use for setting the colors of the LEDs on each port. LAN models typically blink the LEDs when data is transmitted or received on the port. WAN models typically keep the LEDs green unless an error condition exists on the port. With SONET netmods the LED models use the following algorithms: LAN (3 states): if (LOS || LOF || AIS_L || LOP_P || UNEQ_P || PLM_P || LCD) { rxLED = RED } else if (RDI_L) { rxLED = YELLOW } else { rxLED = AUTO } txLED = AUTO WAN (3 states): if (LOS || LOF || AIS_L || LOP_P || UNEQ_P || PLM_P || LCD) { rxLED = RED } else if (RDI_L) { rxLED = YELLOW } else { rxLED = GREEN } txLED = GREEN With LAN and WAN models: RED means fault in receive direction, YELLOW means fault in transmit direction (RDI_L defect), AUTO/GREEN means no fault. Only the receive LED color is changed. These models show only three states and do not reflect the status of the AIS_P and RDI_P defects.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER lan(1), wan(2)  

hwPortTxLED 1.3.6.1.4.1.326.2.2.1.1.2.3.1.17
Indicates the color of the transmit LED for this port. Auto means that the LED is under hardware control. Typically hardware control means that the LED is normally dark with green blinks to indicate data traffic.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER off(1), green(2), red(3), yellow(4), auto(5)  

hwPortRxLED 1.3.6.1.4.1.326.2.2.1.1.2.3.1.18
Indicates the color of the receive LED for this port. Auto means that the LED is under hardware control. Typically hardware control means that the LED is normally dark with green blinks to indicate data traffic.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER off(1), green(2), red(3), yellow(4), auto(5)  

hwPortIfIndex 1.3.6.1.4.1.326.2.2.1.1.2.3.1.19
This entry indicates the IfIndex used to identify this port. It corresponds to the ifIndex used in the rfc2233 rfc1573 ifTables
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwPortRxSyncLED 1.3.6.1.4.1.326.2.2.1.1.2.3.1.20
The synchronization LED which only applies to the receivers. When green, it indicates that the port is providing the 8 khz clock reference to the switch. This is a new entry which makes sense to those netmod ( currently only FRAM netmod support this LED) which can provide a 8 khz clock reference to the switch. At the netmod scope, only one such LED should be green if the switch is importing a port timing clock.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER off(1), green(2)  

hwPortCounterResetTime 1.3.6.1.4.1.326.2.2.1.1.2.3.1.21
Indicates when this port's physical interface counters were reset. The TimeStamp is equal to moduleUptime when the reset occurred. If this ports counters were never reset, hwPortCounterResetTime will be zero. This variable is updated whenever hwPortCounterReset or switchCounterReset is written.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

hwPortCounterReset 1.3.6.1.4.1.326.2.2.1.1.2.3.1.22
Writing a value of resetRequest will result in a reset of all physical interface counters on this port. VCC indexed counters are excluded. A response value of resetTrue indicates a resetRequest has succeeded and is currently in effect. A response value of resetFalse indicates a reset is not currently in effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER resetRequest(1), resetTrue(3), resetFalse(4)  

hwPortSpeed 1.3.6.1.4.1.326.2.2.1.1.2.3.1.23
The speed of this physical port in the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

netmodAlarmsTable 1.3.6.1.4.1.326.2.2.1.1.2.4
A table of network module alarms information categorized on a per slot basis.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NetmodAlarmsEntry

netmodAlarmsEntry 1.3.6.1.4.1.326.2.2.1.1.2.4.1
A table entry containing network module alarm information.
Status: current Access: not-accessible
OBJECT-TYPE    
  NetmodAlarmsEntry  

netmodSlot 1.3.6.1.4.1.326.2.2.1.1.2.4.1.1
This number represents the unique number of this netmod within the ATM switch. This number starts at 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

netmodSlotPriority 1.3.6.1.4.1.326.2.2.1.1.2.4.1.2
The priority assigned to this slot. Possible values are High (corresponding to netmodRemovedHighPrio), Low (corresponding to netmodRemovedLowPrio) and None (default)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER high(1), low(2), none(3)  

netmodStatus 1.3.6.1.4.1.326.2.2.1.1.2.4.1.3
The presence/absence of a netmod in this slot is determined by this variable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER present(1), absent(2)  

netmodName 1.3.6.1.4.1.326.2.2.1.1.2.4.1.4
The name of this netmod. Example: 1A, 3D for ASX4000 and A, B for pre-ASX4000 switches.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

hdcompTable 1.3.6.1.4.1.326.2.2.1.1.2.5
A table for information about HDCOMPs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HdcompEntry

hdcompEntry 1.3.6.1.4.1.326.2.2.1.1.2.5.1
A table for information about HDCOMPs.
Status: current Access: not-accessible
OBJECT-TYPE    
  HdcompEntry  

hdcompIndex 1.3.6.1.4.1.326.2.2.1.1.2.5.1.1
Index of the HDCOMP on the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hdcompDescr 1.3.6.1.4.1.326.2.2.1.1.2.5.1.2
Description of the HDCOMP location on the switch.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..5)  

hdcompAsicVersion 1.3.6.1.4.1.326.2.2.1.1.2.5.1.3
Version number of the HDCOMP ASIC on the switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hdcompVpiLookupErrors 1.3.6.1.4.1.326.2.2.1.1.2.5.1.4
The number of VPI lookup errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hdcompVciLookupErrors 1.3.6.1.4.1.326.2.2.1.1.2.5.1.5
The number of VCI lookup errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAlarmTable 1.3.6.1.4.1.326.2.2.1.4.1.1
A table of switch alarm definitions and configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwAlarmEntry

swAlarmEntry 1.3.6.1.4.1.326.2.2.1.4.1.1.1
A table entry containing switch alarm definitions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwAlarmEntry  

swAlarmType 1.3.6.1.4.1.326.2.2.1.4.1.1.1.1
The type of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER powerSupplyInputFailed(1), powerSupplyOutputFailed(2), fanBankFailed(3), tempSensorOverTemp(4), linkFailed(5), spansFailed(6), powerSupplyOverCurrent(7), powerSupply5VoltFailed(8), netmodRemovedHighPrio(9), netmodRemovedLowPrio(10), fabricRemoved(11), genPortFailure(12), singleTimingRefFailed(13), allTimingRefsFailed(14), singleTCMFailed(15), allTCMsFailed(16)  

swAlarmStatus 1.3.6.1.4.1.326.2.2.1.4.1.1.1.2
The status of this alarm entry. An alarm becomes active if the underlying condition is detected. For power supplies, the input failed alarm condition is asserted if the input voltage is not within the nominal range for the supply. This does not necessarily mean that an ouput failure will result. A power supply output failure condition is asserted if any power supply is failing or if it is physically removed. Power supply output alarms are only applicable to switches with multiple power supplies. Fan bank and temperature sensor failures are applicable only to switches with the appropriate sensing capabilities. Link and spans failures are applicable to all switches.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

swAlarmMinorCategory 1.3.6.1.4.1.326.2.2.1.4.1.1.1.3
This object indicates whether a minor alarm is triggered when this event occurs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swAlarmMajorCategory 1.3.6.1.4.1.326.2.2.1.4.1.1.1.4
This object indicates whether a major alarm is triggered when this event occurs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swAlarmReset 1.3.6.1.4.1.326.2.2.1.4.1.1.1.5
The manager may set this to the value 0 or 1 to cancel a current alarm. This is useful for silencing alarms triggered via edge detection. If this variable is readable, then the alarm is resettable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), enabled(1)  

swAlarmCriticalCategory 1.3.6.1.4.1.326.2.2.1.4.1.1.1.6
This object indicates whether a critical alarm is triggered when this event occurs. This is supported only on certain platforms.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swAlarmACOState 1.3.6.1.4.1.326.2.2.1.4.1.1.1.7
This object indicates the Alarm Cutoff Status(ACO) of this alarm entry. To silence an active alarm relay condition this value can be set to on(1), by pushing the front panel ACO button. The ACO is turned off when the alarm status(SwAlarmStatus) becomes inactive.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

swAlarmMajorRelayState 1.3.6.1.4.1.326.2.2.1.4.1.2
This object indicates the current state of the major alarm relay. If one or more of the alarms (swAlarmType) that are defined major (swAlarmMajorCategory) are currently active (swAlarmStatus), and the alarm cutoff(swAlarmACOState) is off then this object will be on(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

swAlarmMinorRelayState 1.3.6.1.4.1.326.2.2.1.4.1.3
This object indicates the current state of the minor alarm relay. If one or more of the alarms (swAlarmType) that are defined minor (swAlarmMinorCategory) are currently active (swAlarmStatus), and the alarm cutoff(swAlarmACOState) is off then this object will be on(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

swAlarmCriticalRelayState 1.3.6.1.4.1.326.2.2.1.4.1.4
This object indicates the current state of the critical alarm relay. If one or more of the alarms (swAlarmType) that are defined critical (swAlarmCriticalCategory) are currently active (swAlarmStatus), and the alarm cutoff(swAlarmACOState) is off then this object will be on(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

swAlarmRelayTable 1.3.6.1.4.1.326.2.2.1.4.1.5
This table contains the alarm relay definitions for the switch alarms
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwAlarmRelayEntry

swAlarmRelayEntry 1.3.6.1.4.1.326.2.2.1.4.1.5.1
This entry contains the alarm relay definitions for the switch alarms.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwAlarmRelayEntry  

swAlarmRelayIndex 1.3.6.1.4.1.326.2.2.1.4.1.5.1.1
This is the index of the alarm relay on the switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swAlarmRelayFunction 1.3.6.1.4.1.326.2.2.1.4.1.5.1.2
This is the alarm function associated with an alarm relay on the switch. An alarm relay may either be unused, assigned to one of critical, major and minor alarm.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER swUnusedRelay(1), swMajorAlarmRelay(2), swMinorAlarmRelay(3), swCriticalAlarmRelay(4)  

swAlarmRelayState 1.3.6.1.4.1.326.2.2.1.4.1.5.1.3
This is the current state of the alarm relay. The state 'on' means that the alarm relay is activated; the state 'off' means that it is deactivated.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

swAlarmRelayOperMode 1.3.6.1.4.1.326.2.2.1.4.1.5.1.4
This variable represents the operational mode of the relay. The operational mode 'enabled' means that the relay is under software control and the relay state will reflect 'on' or 'off' according to the alarm conditions. 'disabled' will make the alarm relay state always 'off'. 'test' will make it always 'on'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), test(3)  

envMaxNumberOfPowerSupplies 1.3.6.1.4.1.326.2.2.1.4.2.1
The maximum number of power supplies that can be installed on this ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envNumberOfPowerSupplies 1.3.6.1.4.1.326.2.2.1.4.2.2
The number of power supply entries in the power supply table. This is the number of power supplies actually present.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envPowerSupplyTable 1.3.6.1.4.1.326.2.2.1.4.2.3
A table of power supply information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnvPowerSupplyEntry

envPowerSupplyEntry 1.3.6.1.4.1.326.2.2.1.4.2.3.1
A table entry containing power supply information.
Status: current Access: not-accessible
OBJECT-TYPE    
  EnvPowerSupplyEntry  

envPowerSupplyIndex 1.3.6.1.4.1.326.2.2.1.4.2.3.1.1
The index of this power supply.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envPowerSupplyType 1.3.6.1.4.1.326.2.2.1.4.2.3.1.2
The type of this power supply.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER psUnknown(1), psAutoRangeAC(4), ps48VDC(5), psRM1000HA(6), ps30ADC(7), psRM1000HA-C(8)  

envPowerSupplyInputState 1.3.6.1.4.1.326.2.2.1.4.2.3.1.3
The state of the input voltage to this power supply.
Status: current Access: read-only
OBJECT-TYPE    
  GeneralState  

envPowerSupplyOutputState 1.3.6.1.4.1.326.2.2.1.4.2.3.1.4
The status of the output of this power supply. In case there are several output supplies (like +5V, +12V, -12V) this object indicates the aggregate state of all outputs.
Status: current Access: read-only
OBJECT-TYPE    
  GeneralState  

envPowerSupplySerialNumber 1.3.6.1.4.1.326.2.2.1.4.2.3.1.5
The serial number of this power supply, if available.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envPowerSupplyVersion 1.3.6.1.4.1.326.2.2.1.4.2.3.1.6
The version of this power supply, if available.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envPowerSupplyCurrentState 1.3.6.1.4.1.326.2.2.1.4.2.3.1.7
The state of the current on the input return path of this power supply. Should be within 28A +/-2A.
Status: current Access: read-only
OBJECT-TYPE    
  GeneralState  

envPowerSupply5VoltState 1.3.6.1.4.1.326.2.2.1.4.2.3.1.8
The state of the +5V output of this power supply. Should be within tolerance of 5.0 +/-0.1VDC.
Status: current Access: read-only
OBJECT-TYPE    
  GeneralState  

envNumberOfFanBanks 1.3.6.1.4.1.326.2.2.1.4.3.1
The number of fan banks on this ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envFanBanksTable 1.3.6.1.4.1.326.2.2.1.4.3.2
A table of fan bank information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnvFanBanksEntry

envFanBanksEntry 1.3.6.1.4.1.326.2.2.1.4.3.2.1
A table entry containing fan bank information.
Status: current Access: not-accessible
OBJECT-TYPE    
  EnvFanBanksEntry  

envFanBankIndex 1.3.6.1.4.1.326.2.2.1.4.3.2.1.1
The index of this fan bank.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envFanBankState 1.3.6.1.4.1.326.2.2.1.4.3.2.1.3
The status of the fan bank.
Status: current Access: read-only
OBJECT-TYPE    
  GeneralState  

envFanBankSerialNumber 1.3.6.1.4.1.326.2.2.1.4.3.2.1.4
Serial number of the fan tray.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

envFanBankType 1.3.6.1.4.1.326.2.2.1.4.3.2.1.5
The type of fan bank installed.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envFanBankRevision 1.3.6.1.4.1.326.2.2.1.4.3.2.1.6
The revision of the fan bank, as an ASCII character.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envNumberOfTempSensors 1.3.6.1.4.1.326.2.2.1.4.4.1
The number of temperature sensors installed on this ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envTempSensorsTable 1.3.6.1.4.1.326.2.2.1.4.4.2
A table of temperature sensors information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnvTempSensorsEntry

envTempSensorsEntry 1.3.6.1.4.1.326.2.2.1.4.4.2.1
A table entry containing temperature sensor information.
Status: current Access: not-accessible
OBJECT-TYPE    
  EnvTempSensorsEntry  

envTempSensorIndex 1.3.6.1.4.1.326.2.2.1.4.4.2.1.1
The index of this temperature sensor. The value of the index provides an indication of the location and function of the temperature sensor. The set of temperature sensors may vary by switch type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enclosure(1), power-supply-1(2), power-supply-2(3), power-supply-3(4), power-supply-4(5), power-supply-5(6)  

envTempSensorState 1.3.6.1.4.1.326.2.2.1.4.4.2.1.2
The temperature state of this sensor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), overTemp(2)  

envMaxNumberOfCPUs 1.3.6.1.4.1.326.2.2.1.4.5.1
The maximum number of CPUs that can be installed on this ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envNumberOfCPUs 1.3.6.1.4.1.326.2.2.1.4.5.2
The number entries in the CPU table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envCPUsTable 1.3.6.1.4.1.326.2.2.1.4.5.3
A table of CPU information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnvCPUsEntry

envCPUsEntry 1.3.6.1.4.1.326.2.2.1.4.5.3.1
A table entry containing CPU information.
Status: current Access: not-accessible
OBJECT-TYPE    
  EnvCPUsEntry  

envCpuBoard 1.3.6.1.4.1.326.2.2.1.4.5.3.1.1
The board index of this CPU.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envCpuSlot 1.3.6.1.4.1.326.2.2.1.4.5.3.1.2
The slot index of this CPU.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envCpuType 1.3.6.1.4.1.326.2.2.1.4.5.3.1.3
The type of this CPU. The i960 processor further can be of three types - ca, cf and ha.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), sun4e(2), sun4c(3), sparc(4), i960ca(5), i960cf(6), i960ha(7), i960hd(8), p55(9), p6(10), cpv5000(11), p266(12), p200(13)  

envCPUState 1.3.6.1.4.1.326.2.2.1.4.5.3.1.4
The state of the processor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), fail(2), standby(3), boot(4)  

envCpuDRAMSize 1.3.6.1.4.1.326.2.2.1.4.5.3.1.5
The size of the DRAM in bytes installed on the SCP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envCpuRevLevel 1.3.6.1.4.1.326.2.2.1.4.5.3.1.6
The revision level of the processor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envCpuFlashSize 1.3.6.1.4.1.326.2.2.1.4.5.3.1.7
Size of Flash in bytes installed on this SCP board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envCpuBoardRevision 1.3.6.1.4.1.326.2.2.1.4.5.3.1.8
Revision number of this SCP board. A 32-bit number with the most significant 16 bits represent the revison alphabet. For example, 0x20000 represents Rev B, 0xd0000 represents Rev M.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envCpuPromRevision 1.3.6.1.4.1.326.2.2.1.4.5.3.1.9
Revision number of the SCP PROM. Currently only available for boards with i960HA and i960HD processors. A 32-bit number. For example, 0x20000 represents Rev 2.0 and 0x20001 represents Rev 2.1
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envCpuMACAddress 1.3.6.1.4.1.326.2.2.1.4.5.3.1.10
MAC address of ethernet chip on the SCP board.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

envCpuSerialNumber 1.3.6.1.4.1.326.2.2.1.4.5.3.1.11
Serial number of the SCP card. This gives the SCPIM serial number on an ASX-4000.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

envCpuProductPartNumber 1.3.6.1.4.1.326.2.2.1.4.5.3.1.12
Product part number of the SCE. This gives the marketing product part number of RASCAL.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

envCpuCLEI 1.3.6.1.4.1.326.2.2.1.4.5.3.1.13
The Common Language Equipment Identification (CLEI) of this SCP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

envCpuIDESize 1.3.6.1.4.1.326.2.2.1.4.5.3.1.14
Size of IDE disk in bytes installed on this SCP board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envMgmtBoardType 1.3.6.1.4.1.326.2.2.1.4.6.1
The board type of the management station or backplane.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envMgmtBoardRevision 1.3.6.1.4.1.326.2.2.1.4.6.2
The board revision number of the management station or backplane.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envMgmtBoardSerialNumber 1.3.6.1.4.1.326.2.2.1.4.6.3
The serial number of the management station or backplane.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envFabricAlarmTripTemperature 1.3.6.1.4.1.326.2.2.1.4.7.1
The temperature threshold in degrees C at which a fabric temperature alarm will be raised.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

envFabricAlarmResetTemperature 1.3.6.1.4.1.326.2.2.1.4.7.2
The temperature in degrees C at which a fabric temperature alarm will be cancelled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

envFabricTable 1.3.6.1.4.1.326.2.2.1.4.7.3
A table of fabric environmental information
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnvFabricEntry

envFabricEntry 1.3.6.1.4.1.326.2.2.1.4.7.3.1
A table containing fabric environmental information
Status: current Access: not-accessible
OBJECT-TYPE    
  EnvFabricEntry  

envFabricIndex 1.3.6.1.4.1.326.2.2.1.4.7.3.1.1
The index of the fabric
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envFabricTemperature 1.3.6.1.4.1.326.2.2.1.4.7.3.1.2
The temperature measured at the fabric, in degrees C
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

envFabricTemperatureState 1.3.6.1.4.1.326.2.2.1.4.7.3.1.3
The software state of this fabric temperature sensor. This will indicate `normal' until the sensor temperature reaches the current trip threshold. It will then indicate `overTemp' until the temperature reaches the current reset threshold (or until the switch fabric is restarted).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), overTemp(2)  

netmodTimingTable 1.3.6.1.4.1.326.2.2.1.3.1.1
This table is deprecated as the advanced timing options are removed.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NetmodTimingEntry

netmodTimingEntry 1.3.6.1.4.1.326.2.2.1.3.1.1.1
A table entry containing network modeul timing information.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  NetmodTimingEntry  

ntBoard 1.3.6.1.4.1.326.2.2.1.3.1.1.1.1
The index of this board within the ATM switch.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32  

ntModule 1.3.6.1.4.1.326.2.2.1.3.1.1.1.2
The number of this network module within the switch board.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32  

ntPrimaryRecoveredClock 1.3.6.1.4.1.326.2.2.1.3.1.1.1.3
The port number on this network module that provides the primary 8KHz reference clock from its received signal.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32  

ntSecondaryRecoveredClock 1.3.6.1.4.1.326.2.2.1.3.1.1.1.4
The port number on this network module that provides the secondary 8KHz reference clock from its received signal.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32  

ntPrimaryExportClock 1.3.6.1.4.1.326.2.2.1.3.1.1.1.5
The primary 8KHz clock exported by this network module. The exported clock may be used as the network module global clock, which in turn, may be used by all ports that link their transmit clock to the network module global clock. The noClock option is valid only for tp25 (25mb) netmods.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER primaryRecoveredClock(1), crystalClock(2), noClock(3)  

ntSecondaryExportClock 1.3.6.1.4.1.326.2.2.1.3.1.1.1.6
The secondary 8KHz clock exported by this network module. The exported clock may be used as the network module global clock. The secondary exported clock will be used if the primary exported clock is not available. The noClock option is valid only for tp25 (25mb) netmods.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER secondaryRecoveredClock(1), crystalClock(2), noClock(3)  

ntGlobalClock 1.3.6.1.4.1.326.2.2.1.3.1.1.1.7
The global 8KHz clock that is available to every port on this network module, when the port links its trasnmit clock to the network module global clock.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER exportClock(1), importClock(2)  

ntExportClockOperStatus 1.3.6.1.4.1.326.2.2.1.3.1.1.1.8
The currently active 8KHz clock configuration. The tertiaryClock(3) is determined by the switch control software if both the primary and secondary clocks are not available.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER primaryClock(1), secondaryClock(2), crystalClock(3)  

ntPrimaryImportClock 1.3.6.1.4.1.326.2.2.1.3.1.1.1.9
The primary 8kHz clock imported by this network module. The imported clock may be used as the network module global clock, which in turn, may be used by all ports that link their transmit clock to the network module global clock.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER netmodAExportClock(1), netmodBExportClock(2), netmodCExportClock(3), netmodDExportClock(4), board1PrimaryClock(5), board2PrimaryClock(6), board3PrimaryClock(7), board4PrimaryClock(8), managementStationClock(9)  

ntSecondaryImportClock 1.3.6.1.4.1.326.2.2.1.3.1.1.1.10
The secondary 8kHz clock imported by this network module. The imported clock may be used as the network module global clock. The secondary imported clock will be used if the primary imported clock is not available.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER netmodAExportClock(1), netmodBExportClock(2), netmodCExportClock(3), netmodDExportClock(4), board1PrimaryClock(5), board2PrimaryClock(6), board3PrimaryClock(7), board4PrimaryClock(8), managementStationClock(9)  

ntImportClockOperStatus 1.3.6.1.4.1.326.2.2.1.3.1.1.1.11
The currently active 8kHz import clock configuration. The tertiaryClock(3) is determined by the switch control software if both the primary and secondary clocks are not available.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER primaryClock(1), secondaryClock(2), netmodExportClock(3)  

boardTimingTable 1.3.6.1.4.1.326.2.2.1.3.2.1
This table is deprecated as the advanced timing options are removed.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BoardTimingEntry

boardTimingEntry 1.3.6.1.4.1.326.2.2.1.3.2.1.1
A table entry containing switch board timing information.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  BoardTimingEntry  

btBoard 1.3.6.1.4.1.326.2.2.1.3.2.1.1.1
The index of this board within the ATM switch.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32  

btPrimaryClock 1.3.6.1.4.1.326.2.2.1.3.2.1.1.2
The source of the primary 8kHz clock for this board. The clock may be used by each network module in the switch as the network module import clock. The clock may also be used by the management station as the primary or secondary source of the Stratum 3E clock.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER netmodAExportClock(1), netmodBExportClock(2), netmodCExportClock(3), netmodDExportClock(4), netmodNone(5)  

btSecondaryClock 1.3.6.1.4.1.326.2.2.1.3.2.1.1.3
The source of the secondary 8kHz clock. The clock may be used by the management station as the primary or secondary source of the Stratum 3E clock.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER netmodAExportClock(1), netmodBExportClock(2), netmodCExportClock(3), netmodDExportClock(4), netmodNone(5)  

btPrimaryClockOperStatus 1.3.6.1.4.1.326.2.2.1.3.2.1.1.4
The current state of the 8kHz primary clock.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER clockUp(1), clockDown(2)  

btSecondaryClockOperStatus 1.3.6.1.4.1.326.2.2.1.3.2.1.1.5
The current state of the 8kHz secondary clock.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER clockUp(1), clockDown(2)  

shmemConfTable 1.3.6.1.4.1.326.2.2.1.5.1.1
A table for shared memory network modules configuration. Implementation of this table is mandatory if at least one of the network modules' hardware is based on shared memory. The user should walk this table and select the shared memory configuration that suits his/her needs. The selection is done in the specific network module shared memory configuration entry (netmodShmemTable).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ShmemConfEntry

shmemConfEntry 1.3.6.1.4.1.326.2.2.1.5.1.1.1
A table entry containing shared memory network module configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  ShmemConfEntry  

shmemConfIndex 1.3.6.1.4.1.326.2.2.1.5.1.1.1.1
The index of this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmemUcastConnections 1.3.6.1.4.1.326.2.2.1.5.1.1.1.2
The maximum number of unicast connections that is supported by this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmemMcastConnections 1.3.6.1.4.1.326.2.2.1.5.1.1.1.3
The maximum number of multicast connections that is supported by this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmemVpiVciLists 1.3.6.1.4.1.326.2.2.1.5.1.1.1.4
The memory allocated for VPI/VCI lists (which is used for multicast connections) by this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmemCellsBuffers 1.3.6.1.4.1.326.2.2.1.5.1.1.1.5
The number of cells buffers that is supported by this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmemConfName 1.3.6.1.4.1.326.2.2.1.5.1.1.1.6
The name of this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

shmemMemorySize 1.3.6.1.4.1.326.2.2.1.5.1.1.1.7
The size of this shared memory configuration in units of 48 bit words (x48).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

netmodShmemTable 1.3.6.1.4.1.326.2.2.1.5.1.2
A table for shared memory network modules configuration. Implementation of this table is mandatory if the network module hardware is based on shared memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NetmodShmemEntry

netmodShmemEntry 1.3.6.1.4.1.326.2.2.1.5.1.2.1
A table entry containing shared memory network module configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  NetmodShmemEntry  

nshmemBoard 1.3.6.1.4.1.326.2.2.1.5.1.2.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nshmemModule 1.3.6.1.4.1.326.2.2.1.5.1.2.1.2
The number of this network module within the switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nshmemConfRow 1.3.6.1.4.1.326.2.2.1.5.1.2.1.3
This object identify the row in the shared memory configuration table that was selected for this network module.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nshmemConfSharedMemory 1.3.6.1.4.1.326.2.2.1.5.1.2.1.4
The amount of memory that was configured for this network module given all the user requirements as specified in the selected shared memory configuration row.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nshmemCurrentUcastConnections 1.3.6.1.4.1.326.2.2.1.5.1.2.1.5
The current number of unicast connections active on this shared memory network module.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nshmemCurrentMcastConnections 1.3.6.1.4.1.326.2.2.1.5.1.2.1.6
The current number of multicast connections active on this shared memory network module.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nshmemCurrentVpiVciLists 1.3.6.1.4.1.326.2.2.1.5.1.2.1.7
The current number of VPI/VCI lists active on this shared memory network module.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nshmemCurrentCellsBuffers 1.3.6.1.4.1.326.2.2.1.5.1.2.1.8
The current number cells buffers active on this shared memory network module.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nshmemCurrentSharedMemory 1.3.6.1.4.1.326.2.2.1.5.1.2.1.9
The current value of the used shared memory on this network module.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nshmemConfAal5PacketDrop 1.3.6.1.4.1.326.2.2.1.5.1.2.1.10
The AAL5 packet drop threshold in percentage of cells. The switch software provides a reasonable default, however, the user may wish to change this value according to the type of traffic and size of packets being transmitted on the network.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nshmemAssertXACPT 1.3.6.1.4.1.326.2.2.1.5.1.2.1.11
This variable establishes the setting fo the XACPT bit in the fs200sm main control register (section 3.1). This bit determines whether the signal XACPT is asserted whenever the shared memory is full. XACPT prevents the switch from sending cells to the network module. This bit takes advantage of any buffers on the switch to reduce cell loss, but it should not be used if guaranteed cell delay is being provided to high priority cells.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clearXACPT(1), assertXACPT(2)  

nshmemMemorySize 1.3.6.1.4.1.326.2.2.1.5.1.2.1.12
The size of this Series-C network module's shared memory in units of 48 bit words (x48).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portShmemConfTable 1.3.6.1.4.1.326.2.2.1.5.2.1
A table for shared memory network modules configuration that is specified on a port basis. Implementation of this table is mandatory if the network module hardware is based on shared memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortShmemConfEntry

portShmemConfEntry 1.3.6.1.4.1.326.2.2.1.5.2.1.1
A table entry containing port configuration information for shared memory network modules.
Status: current Access: not-accessible
OBJECT-TYPE    
  PortShmemConfEntry  

pshmemConfBoard 1.3.6.1.4.1.326.2.2.1.5.2.1.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pshmemConfModule 1.3.6.1.4.1.326.2.2.1.5.2.1.1.2
The number of this network module within the switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pshmemConfPort 1.3.6.1.4.1.326.2.2.1.5.2.1.1.3
The number of this port within the switch board and network module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pshmemMaxCDVforCBR 1.3.6.1.4.1.326.2.2.1.5.2.1.1.4
The maximum transmitting CDV (Cell Delay Variation) in microseconds for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pshmemMaxCDVforVBR 1.3.6.1.4.1.326.2.2.1.5.2.1.1.5
The maximum transmitting CDV (Cell Delay Variation) in microseconds for nrtVBR (Non-Real-Time Variable Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pshmemQsizeforABR 1.3.6.1.4.1.326.2.2.1.5.2.1.1.6
The dedicated queue size in cells for ABR (Available Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pshmemEfciOnABR 1.3.6.1.4.1.326.2.2.1.5.2.1.1.7
The treshold on which the EFCI (Explicit Forward Congestion Indication) bit is turned on for ABR (Available Bit Rate) and UBR (Unspecified Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pshmemEfciOffABR 1.3.6.1.4.1.326.2.2.1.5.2.1.1.8
The treshold on which the EFCI (Explicit Forward Congestion Indication) bit is turned off for ABR (Available Bit Rate) and UBR (Unspecified Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pshmemQsizeforCBR 1.3.6.1.4.1.326.2.2.1.5.2.1.1.9
The dedicated queue size in cells for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pshmemQsizeforVBR 1.3.6.1.4.1.326.2.2.1.5.2.1.1.10
The dedicated queue size in cells for nrtVBR (Non-Real-Time Variable Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pshmemClpThreshforCBR 1.3.6.1.4.1.326.2.2.1.5.2.1.1.11
The CLP=1 discard threshold in cells for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pshmemClpThreshforVBR 1.3.6.1.4.1.326.2.2.1.5.2.1.1.12
The CLP=1 discard threshold in cells for nrtVBR (Non-Real-Time Variable Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pshmemClpThreshforABR 1.3.6.1.4.1.326.2.2.1.5.2.1.1.13
The CLP=1 discard threshold in cells for ABR (Available Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pShmemAtmInterfaceIndex 1.3.6.1.4.1.326.2.2.1.5.2.1.1.14
The Atm interface index correspong to this port. This is also the index of the portTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portShmemTable 1.3.6.1.4.1.326.2.2.1.5.2.2
A table for current state of port on shared memory network modules. Implementation of this table is mandatory if the network module hardware is based on shared memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortShmemEntry

portShmemEntry 1.3.6.1.4.1.326.2.2.1.5.2.2.1
A table entry containing current port configuration information for shared memory network modules.
Status: current Access: not-accessible
OBJECT-TYPE    
  PortShmemEntry  

pshmemBoard 1.3.6.1.4.1.326.2.2.1.5.2.2.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pshmemModule 1.3.6.1.4.1.326.2.2.1.5.2.2.1.2
The number of this network module within the switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pshmemPort 1.3.6.1.4.1.326.2.2.1.5.2.2.1.3
The number of this port within the switch board and network module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pshmemPriority 1.3.6.1.4.1.326.2.2.1.5.2.2.1.4
The traffic type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER priorityUBR-ABR(1), priorityVBR(2), priorityCBR(3)  

pshmemClpThreshold 1.3.6.1.4.1.326.2.2.1.5.2.2.1.5
The threshold level in number of cells in which CLP=1 cells will be dropped.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pshmemDedicatedQsize 1.3.6.1.4.1.326.2.2.1.5.2.2.1.6
The dedicated queue size for this type of traffic as was calculated by the switch software. The dedicated queue size is determined by the configured maximum CDV (Cell Delay Variation) for CBR/rtVBR (Constant Bit Rate / Real-Time Variable Bit Rate) and nrtVBR (Non-Real-Time Variable Bit Rate) as well as the configurable queue size for ABR (Available Bit Rate) and UBR (Unspecified Bit Rate) traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pshmemCurrentQsize 1.3.6.1.4.1.326.2.2.1.5.2.2.1.7
The current size of the queue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pshmemTxCells 1.3.6.1.4.1.326.2.2.1.5.2.2.1.8
The number of cells that were transmitted for this port and priority queue.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pshmemLostCells 1.3.6.1.4.1.326.2.2.1.5.2.2.1.9
The total number of cells that were lost for this port and priority queue.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

shmem2ConfTable 1.3.6.1.4.1.326.2.2.1.5.3.1
A table for shared memory network modules configuration. Implementation of this table is mandatory if at least one of the network modules' hardware is based on shared memory. The user should walk this table and select the shared memory configuration that suits his/her needs. The selection is done in the specific network module shared memory configuration entry (netmodShmemTable).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Shmem2ConfEntry

shmem2ConfEntry 1.3.6.1.4.1.326.2.2.1.5.3.1.1
A table entry containing shared memory network module configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Shmem2ConfEntry  

shmem2ConfIndex 1.3.6.1.4.1.326.2.2.1.5.3.1.1.1
The index of this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmem2UcastConnections 1.3.6.1.4.1.326.2.2.1.5.3.1.1.2
The maximum number of unicast connections that is supported by this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmem2McastConnections 1.3.6.1.4.1.326.2.2.1.5.3.1.1.3
The maximum number of multicast connections that is supported by this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmem2CellsBuffers 1.3.6.1.4.1.326.2.2.1.5.3.1.1.4
The number of cells buffers that is supported by this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmem2ConfName 1.3.6.1.4.1.326.2.2.1.5.3.1.1.5
The name of this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

shmem2Counters 1.3.6.1.4.1.326.2.2.1.5.3.1.1.6
The number of counters that is supported by this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmem2CellMemorySize 1.3.6.1.4.1.326.2.2.1.5.3.1.1.7
The size of this shared memory cell RAM configuration in units of 64 bit words (x64).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmem2TableMemorySize 1.3.6.1.4.1.326.2.2.1.5.3.1.1.8
The size of this shared memory table RAM configuration in units of 32 bit words (x32).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmem2NumPriorities 1.3.6.1.4.1.326.2.2.1.5.3.1.1.9
The number of priorities that this shared memory configuration supports.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

netmodShmem2Table 1.3.6.1.4.1.326.2.2.1.5.3.2
A table for shared memory network modules configuration. Implementation of this table is mandatory if the network module hardware is based on shared memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NetmodShmem2Entry

netmodShmem2Entry 1.3.6.1.4.1.326.2.2.1.5.3.2.1
A table entry containing shared memory network module configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  NetmodShmem2Entry  

nShmem2Board 1.3.6.1.4.1.326.2.2.1.5.3.2.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nShmem2Module 1.3.6.1.4.1.326.2.2.1.5.3.2.1.2
The number of this network module within the switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nShmem2ConfRow 1.3.6.1.4.1.326.2.2.1.5.3.2.1.3
This object identify the row in the shared memory configuration table that was selected for this network module.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem2ConfSharedMemory 1.3.6.1.4.1.326.2.2.1.5.3.2.1.4
The amount of memory that was configured for this network module given all the user requirements as specified in the selected shared memory configuration row.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nShmem2CurrentUcastConnections 1.3.6.1.4.1.326.2.2.1.5.3.2.1.5
The current number of unicast connections active on this shared memory network module.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nShmem2CurrentMcastConnections 1.3.6.1.4.1.326.2.2.1.5.3.2.1.6
The current number of multicast connections active on this shared memory network module.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nShmem2CurrentCellsBuffers 1.3.6.1.4.1.326.2.2.1.5.3.2.1.7
The current number cells buffers active on this shared memory network module.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nShmem2CurrentSharedMemory 1.3.6.1.4.1.326.2.2.1.5.3.2.1.8
The current value of the used shared memory on this network module.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nShmem2ConfAal5PacketDrop 1.3.6.1.4.1.326.2.2.1.5.3.2.1.9
The AAL5 packet drop threshold in percentage of cells. The switch software provides a reasonable default, however, the user may wish to change this value according to the type of traffic and size of packets being transmitted on the network.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem2ConfAal5PacketDropforUBR 1.3.6.1.4.1.326.2.2.1.5.3.2.1.10
The AAL5 packet drop threshold, in percentage of cells for UBR queue in a four priority configuration or priorityNrt queue in a two priority configuration. The switch software provides a reasonable default. However, the user may wish to change this value according to the type of traffic and size of packets being transmitted on the network.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem2ConfEfciOn 1.3.6.1.4.1.326.2.2.1.5.3.2.1.11
The threshold on which the EFCI (Explicit Forward Congestion Indication) is enabled for UBR (Unspecified Bit Rate) and ABR (Available Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem2ConfEfciOff 1.3.6.1.4.1.326.2.2.1.5.3.2.1.12
The threshold on which the EFCI (Explicit Forward Congestion Indication) is disabled for UBR (Unspecified Bit Rate) and ABR (Available Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem2CellMemorySize 1.3.6.1.4.1.326.2.2.1.5.3.2.1.13
The size of this shared memory cell RAM configuration in units of 64 bit words (x64).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nShmem2TableMemorySize 1.3.6.1.4.1.326.2.2.1.5.3.2.1.14
The size of this shared memory table RAM configuration in units of 32 bit words (x32).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nShmem2NumPriorities 1.3.6.1.4.1.326.2.2.1.5.3.2.1.15
The number of priorities that this network module supports.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nShmem2VBRPriority 1.3.6.1.4.1.326.2.2.1.5.3.2.1.16
The queue through which VBR traffic is routed in a two priority configuration (priorityRt or priorityNrt). For a four priority configuration, it is unSupported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER priorityRt(1), priorityNrt(2), unSupported(3)  

portShmem2ConfTable 1.3.6.1.4.1.326.2.2.1.5.4.1
A table for shared memory network modules configuration that is specified on a port basis. Implementation of this table is mandatory if the network module hardware is based on shared memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortShmem2ConfEntry

portShmem2ConfEntry 1.3.6.1.4.1.326.2.2.1.5.4.1.1
A table entry containing port configuration information for shared memory network modules.
Status: current Access: not-accessible
OBJECT-TYPE    
  PortShmem2ConfEntry  

pShmem2ConfBoard 1.3.6.1.4.1.326.2.2.1.5.4.1.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem2ConfModule 1.3.6.1.4.1.326.2.2.1.5.4.1.1.2
The number of this network module within the switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem2ConfPort 1.3.6.1.4.1.326.2.2.1.5.4.1.1.3
The number of this port within the switch board and network module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem2QsizeforCBR 1.3.6.1.4.1.326.2.2.1.5.4.1.1.4
The dedicated queue size in cells for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem2QsizeforVBR 1.3.6.1.4.1.326.2.2.1.5.4.1.1.5
The dedicated queue size in cells for nrtVBR (Non-Real-Time Variable Bit Rate) traffic.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem2QsizeforABR 1.3.6.1.4.1.326.2.2.1.5.4.1.1.6
The dedicated queue size in cells for ABR (Available Bit Rate) traffic.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem2QsizeforUBR 1.3.6.1.4.1.326.2.2.1.5.4.1.1.7
The dedicated queue size in cells for UBR (Unspecified Bit Rate) traffic.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem2ClpThreshforCBR 1.3.6.1.4.1.326.2.2.1.5.4.1.1.8
The CLP=1 discard threshold in cells for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem2ClpThreshforVBR 1.3.6.1.4.1.326.2.2.1.5.4.1.1.9
The CLP=1 discard threshold in cells for nrtVBR (Non-Real-Time Variable Bit Rate) traffic.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem2ClpThreshforABR 1.3.6.1.4.1.326.2.2.1.5.4.1.1.10
The CLP=1 discard threshold in cells for ABR (Available Bit Rate) traffic.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem2ClpThreshforUBR 1.3.6.1.4.1.326.2.2.1.5.4.1.1.11
The CLP=1 discard threshold in cells for UBR (Unspecified Bit Rate) traffic.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem2AtmInterfaceIndex 1.3.6.1.4.1.326.2.2.1.5.4.1.1.12
The Atm interface index correspong to this port. This is also the index of the portTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portPriorityShmem2ConfTable 1.3.6.1.4.1.326.2.2.1.5.4.3
A table for shared memory network modules configuration that is specified on a port-priority basis. Implementation of this table is mandatory if the network module hardware is based on shared memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortPriorityShmem2ConfEntry

portPriorityShmem2ConfEntry 1.3.6.1.4.1.326.2.2.1.5.4.3.1
A table entry containing port-priority configuration information for shared memory network modules.
Status: current Access: not-accessible
OBJECT-TYPE    
  PortPriorityShmem2ConfEntry  

ppShmem2ConfBoard 1.3.6.1.4.1.326.2.2.1.5.4.3.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ppShmem2ConfModule 1.3.6.1.4.1.326.2.2.1.5.4.3.1.2
The number of this network module within the switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ppShmem2ConfPort 1.3.6.1.4.1.326.2.2.1.5.4.3.1.3
The number of this port within the switch board and the network module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ppShmem2ConfPriority 1.3.6.1.4.1.326.2.2.1.5.4.3.1.4
The priority queue in the shared memory network module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER priorityABR(1), priorityVBR(2), priorityCBR(3), priorityUBR(4), priorityRt(5), priorityNrt(6)  

ppShmem2Qsize 1.3.6.1.4.1.326.2.2.1.5.4.3.1.5
The dedicated queue size for this port-priority combination, in number of cells.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

ppShmem2ClpThreshold 1.3.6.1.4.1.326.2.2.1.5.4.3.1.6
CLP=1 threshold of this port-priority combination, in number of cells.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

portShmem2Table 1.3.6.1.4.1.326.2.2.1.5.4.2
A table for current state of port on shared memory network modules. Implementation of this table is mandatory if the network module hardware is based on shared memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortShmem2Entry

portShmem2Entry 1.3.6.1.4.1.326.2.2.1.5.4.2.1
A table entry containing current port configuration information for shared memory network modules.
Status: current Access: not-accessible
OBJECT-TYPE    
  PortShmem2Entry  

pShmem2Board 1.3.6.1.4.1.326.2.2.1.5.4.2.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem2Module 1.3.6.1.4.1.326.2.2.1.5.4.2.1.2
The number of this network module within the switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem2Port 1.3.6.1.4.1.326.2.2.1.5.4.2.1.3
The number of this port within the switch board and network module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem2Priority 1.3.6.1.4.1.326.2.2.1.5.4.2.1.4
The priority queue in the shared memory network module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER priorityABR(1), priorityVBR(2), priorityCBR(3), priorityUBR(4), priorityRt(5), priorityNrt(6)  

pShmem2ClpThreshold 1.3.6.1.4.1.326.2.2.1.5.4.2.1.5
The threshold level in number of cells in which CLP=1 cells will be dropped.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem2DedicatedQsize 1.3.6.1.4.1.326.2.2.1.5.4.2.1.6
The dedicated queue size for this type of traffic as was calculated by the switch software. The dedicated queue size is determined by the configured maximum CDV (Cell Delay Variation) for CBR/rtVBR (Constant Bit Rate / Real-Time Variable Bit Rate) and nrtVBR (Non-Real-Time Variable Bit Rate) as well as the configurable queue size for ABR (Available Bit Rate) and UBR (Unspecified Bit Rate) traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem2CurrentQsize 1.3.6.1.4.1.326.2.2.1.5.4.2.1.7
The current size of the queue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem2TxCells 1.3.6.1.4.1.326.2.2.1.5.4.2.1.8
The number of cells that were transmitted for this port and priority queue.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pShmem2LostCells 1.3.6.1.4.1.326.2.2.1.5.4.2.1.9
The total number of cells that were lost for this port and priority queue.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pShmem2IntentionalLostCells 1.3.6.1.4.1.326.2.2.1.5.4.2.1.10
The number of cells that were lost for this port and priority queue due to EPD (Early Packet Discard) or PPD (Partial Packet Discard).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pShmem2UnintentionalLostCells 1.3.6.1.4.1.326.2.2.1.5.4.2.1.11
The number of cells that were lost for this port and priority queue due to output memory shortages or the CLP (Cell Loss Priority) threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

channelShmem2Table 1.3.6.1.4.1.326.2.2.1.5.5.1
A table of information about the channels through this shared memory network module.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ChannelShmem2Entry

channelShmem2Entry 1.3.6.1.4.1.326.2.2.1.5.5.1.1
A table entry containing channel shmem2 information.
Status: current Access: not-accessible
OBJECT-TYPE    
  ChannelShmem2Entry  

vcShmem2OutputPort 1.3.6.1.4.1.326.2.2.1.5.5.1.1.1
The value of this object identifies the output port of this channel and is the same as the opathPort, and portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vcShmem2OutputVPI 1.3.6.1.4.1.326.2.2.1.5.5.1.1.2
The value of this object identifies the output VPI (Virtual Path Identifier) of this channel and is the same as the opathVPI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vcShmem2OutputVCI 1.3.6.1.4.1.326.2.2.1.5.5.1.1.3
The output VCI (Virtual Channel Identifier) of this channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vcShmem2TotalLostCells 1.3.6.1.4.1.326.2.2.1.5.5.1.1.4
The number of cells on this channel that were dropped by the output network module.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vcShmem2IntentionalLostCells 1.3.6.1.4.1.326.2.2.1.5.5.1.1.5
The number of cells on this channel that were dropped due to EPD (Early Packet Discard) or PPD (Partial Packet Discard).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vcShmem2UnintentionalLostCells 1.3.6.1.4.1.326.2.2.1.5.5.1.1.6
The number of cells on this channel that were dropped due to output memory shortages or the CLP (Cell Loss Priority) threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vcShmem2TransmittedCells 1.3.6.1.4.1.326.2.2.1.5.5.1.1.7
The number of cells on this channel that were transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pathShmem2Table 1.3.6.1.4.1.326.2.2.1.5.5.2
A table of information about the paths through this shared memory network module.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PathShmem2Entry

pathShmem2Entry 1.3.6.1.4.1.326.2.2.1.5.5.2.1
A table entry containing path shmem2 information.
Status: current Access: not-accessible
OBJECT-TYPE    
  PathShmem2Entry  

vpShmem2OutputPort 1.3.6.1.4.1.326.2.2.1.5.5.2.1.1
The value of this object identifies the output port of this path and is the same as the portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vpShmem2OutputVPI 1.3.6.1.4.1.326.2.2.1.5.5.2.1.2
The output VPI (Virtual Path Identifier) of this path.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vpShmem2TotalLostCells 1.3.6.1.4.1.326.2.2.1.5.5.2.1.3
The number of cells on this path that were dropped by the output network module.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vpShmem2IntentionalLostCells 1.3.6.1.4.1.326.2.2.1.5.5.2.1.4
The number of cells on this path that were dropped due to EPD (Early Packet Discard) or PPD (Partial Packet Discard).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vpShmem2UnintentionalLostCells 1.3.6.1.4.1.326.2.2.1.5.5.2.1.5
The number of cells on this path that were dropped due to output memory shortages or the CLP (Cell Loss Priority) threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vpShmem2TransmittedCells 1.3.6.1.4.1.326.2.2.1.5.5.2.1.6
The number of cells on this path that were transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

netmodShmem2CustomBCSTable 1.3.6.1.4.1.326.2.2.1.5.3.3
A table for shared memory custom BCS mappings
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NetmodShmem2CustomBCSEntry

netmodShmem2CustomBCSEntry 1.3.6.1.4.1.326.2.2.1.5.3.3.1
A table entry containing shared memory custom BCS mappings
Status: current Access: not-accessible
OBJECT-TYPE    
  NetmodShmem2CustomBCSEntry  

nShmem2CustomBCSBoard 1.3.6.1.4.1.326.2.2.1.5.3.3.1.1
The index of this board within the ATM switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

nShmem2CustomBCSModule 1.3.6.1.4.1.326.2.2.1.5.3.3.1.2
The number of this network module within the switch board.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

nShmem2CustomBCSValue 1.3.6.1.4.1.326.2.2.1.5.3.3.1.3
The value of this BCS
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

nShmem2CustomBCSWeight 1.3.6.1.4.1.326.2.2.1.5.3.3.1.4
The weight assigned to this BCS
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem2CustomBCSRowStatus 1.3.6.1.4.1.326.2.2.1.5.3.3.1.5
Administrative status of this entry
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

shmem3ConfTable 1.3.6.1.4.1.326.2.2.1.5.6.1
A table for shared memory network modules configuration. Implementation of this table is mandatory if at least one of the network modules' hardware is based on shared memory. The user should walk this table and select the shared memory configuration that suits his/her needs. The selection is done in the specific network module shared memory configuration entry (netmodShmemTable).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Shmem3ConfEntry

shmem3ConfEntry 1.3.6.1.4.1.326.2.2.1.5.6.1.1
A table entry containing shared memory network module configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Shmem3ConfEntry  

shmem3ConfIndex 1.3.6.1.4.1.326.2.2.1.5.6.1.1.1
The index of this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmem3UcastConnections 1.3.6.1.4.1.326.2.2.1.5.6.1.1.2
The maximum number of unicast connections that is supported by this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmem3McastConnections 1.3.6.1.4.1.326.2.2.1.5.6.1.1.3
The maximum number of multicast connections that is supported by this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmem3VpiVciLists 1.3.6.1.4.1.326.2.2.1.5.6.1.1.4
The memory allocated for VPI/VCI lists (which is used for multicast connections) by this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmem3CellsBuffers 1.3.6.1.4.1.326.2.2.1.5.6.1.1.5
The number of cells buffers that is supported by this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmem3ConfName 1.3.6.1.4.1.326.2.2.1.5.6.1.1.6
The name of this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

shmem3Counters 1.3.6.1.4.1.326.2.2.1.5.6.1.1.7
The number of counters that is supported by this shared memory configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmem3CellMemorySize 1.3.6.1.4.1.326.2.2.1.5.6.1.1.8
The size of this shared memory cell RAM configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

shmem3TableMemorySize 1.3.6.1.4.1.326.2.2.1.5.6.1.1.9
The size of this shared memory table RAM configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

netmodShmem3Table 1.3.6.1.4.1.326.2.2.1.5.6.2
A table for shared memory network modules configuration. Implementation of this table is mandatory if the network module hardware is based on shared memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NetmodShmem3Entry

netmodShmem3Entry 1.3.6.1.4.1.326.2.2.1.5.6.2.1
A table entry containing shared memory network module configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  NetmodShmem3Entry  

nShmem3Board 1.3.6.1.4.1.326.2.2.1.5.6.2.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nShmem3Module 1.3.6.1.4.1.326.2.2.1.5.6.2.1.2
The number of this network module within the switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nShmem3ConfRow 1.3.6.1.4.1.326.2.2.1.5.6.2.1.3
This object identify the row in the shared memory configuration table that was selected for this network module.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem3ConfSharedMemory 1.3.6.1.4.1.326.2.2.1.5.6.2.1.4
The amount of memory that was configured for this network module given all the user requirements as specified in the selected shared memory configuration row.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nShmem3CurrentUcastConnections 1.3.6.1.4.1.326.2.2.1.5.6.2.1.5
The current number of unicast connections active on this shared memory network module.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nShmem3CurrentMcastConnections 1.3.6.1.4.1.326.2.2.1.5.6.2.1.6
The current number of multicast connections active on this shared memory network module.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nShmem3CurrentVpiVciLists 1.3.6.1.4.1.326.2.2.1.5.6.2.1.7
The current number of VPI/VCI lists active on this shared memory network module.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nShmem3CurrentCellsBuffers 1.3.6.1.4.1.326.2.2.1.5.6.2.1.8
The current number cells buffers active on this shared memory network module.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nShmem3ConfAal5PacketDrop 1.3.6.1.4.1.326.2.2.1.5.6.2.1.10
The AAL5 packet drop threshold in number of cells. The switch software provides a reasonable default, however, the user may wish to change this value according to the type of traffic and size of packets being transmitted on the network. Must be between 0 and 32767
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem3ConfAal5PacketDropforUBR 1.3.6.1.4.1.326.2.2.1.5.6.2.1.11
The AAL5 packet drop threshold for UBR traffic in percentage of cells. The switch software provides a reasonable default, however, the user may wish to change this value according to the type of traffic and size of packets being transmitted on the network. Must be between 0 and 32767
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem3ConfEfciOn 1.3.6.1.4.1.326.2.2.1.5.6.2.1.12
The threshold on which the EFCI (Explicit Forward Congestion Indication) is enabled for UBR (Unspecified Bit Rate) and ABR (Available Bit Rate) traffic. Must be a multiple of 32, greater than or equal to EFCI-off threshold, and less than or equal to 32736.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem3ConfEfciOff 1.3.6.1.4.1.326.2.2.1.5.6.2.1.13
The threshold on which the EFCI (Explicit Forward Congestion Indication) is disabled for UBR (Unspecified Bit Rate) and ABR (Available Bit Rate) traffic. Must be a multiple of 32, greater than or equal to 32, and less than or equal to EFCI-on threshold.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem3CellMemorySize 1.3.6.1.4.1.326.2.2.1.5.6.2.1.14
The physical size of this shared memory cell RAM configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nShmem3TableMemorySize 1.3.6.1.4.1.326.2.2.1.5.6.2.1.15
The physical size of this shared memory table RAM configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nShmem3ConfCountPackets 1.3.6.1.4.1.326.2.2.1.5.6.2.1.16
Setting this variable to enable(1) causes the network module to count the number of AAL5 packets.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

nShmem3ConfAltCLP1Threshold 1.3.6.1.4.1.326.2.2.1.5.6.2.1.17
Alternate CLP=1 threshold for nrt-VBR service class. Must be a multiple of 16, greater than or equal to 0, and less than AltCLP01 threshold.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem3ConfAltCLP01Threshold 1.3.6.1.4.1.326.2.2.1.5.6.2.1.18
Alternate CLP=0+1 threshold for nrt-VBR service class. Must be a multiple of 16, greater than AltCLP1 threshold and less than or equal to 4080.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem3ConfVcCLP1ForCBR 1.3.6.1.4.1.326.2.2.1.5.6.2.1.19
Per class CLP=1 threshold for CBR/rtVBR service class. Must be a multiple of 16, greater than or equal to 0, and less than VcCLP01ForCBR threshold.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem3ConfVcCLP01ForCBR 1.3.6.1.4.1.326.2.2.1.5.6.2.1.20
Per class CLP=0+1 threshold for CBR/rtVBR service class. Must be a multiple of 16, greater than VcCLP1ForCBR threshold, and less than or equal to 4080.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem3ConfVcCLP1ForVBR 1.3.6.1.4.1.326.2.2.1.5.6.2.1.21
Per class CLP=1 threshold for nrt-VBR service class. Must be a multiple of 16, greater than or equal to 0, and less than VcCLP01ForVBR threshold.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem3ConfVcCLP01ForVBR 1.3.6.1.4.1.326.2.2.1.5.6.2.1.22
Per class CLP=0+1 threshold for nrt-VBR service class. Must be a multiple of 16, greater than VcCLP1ForVBR threshold, and less than or equal to 4080.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem3ConfVcCLP1ForABR 1.3.6.1.4.1.326.2.2.1.5.6.2.1.23
Per class CLP=1 threshold for ABR service class. Must be a multiple of 16, greater than or equal to 0, and less than VcCLP01ForABR threshold.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem3ConfVcCLP01ForABR 1.3.6.1.4.1.326.2.2.1.5.6.2.1.24
Per class CLP=0+1 threshold for ABR service class. Must be a multiple of 16, greater than VcCLP1ForABR threshold, and less than or equal to 4080.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem3ConfVcCLP1ForUBR 1.3.6.1.4.1.326.2.2.1.5.6.2.1.25
Per class CLP=1 threshold for UBR service class. Must be a multiple of 16, greater than or equal to 0, and less than VcCLP01ForUBR threshold.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nShmem3ConfVcCLP01ForUBR 1.3.6.1.4.1.326.2.2.1.5.6.2.1.26
Per class CLP=0+1 threshold for UBR service class. Must be a multiple of 16, greater than VcCLP1ForUBR threshold, and less than or equal to 4080.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

portShmem3ConfTable 1.3.6.1.4.1.326.2.2.1.5.7.1
A table for shared memory network modules configuration that is specified on a port basis. Implementation of this table is mandatory if the network module hardware is based on shared memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortShmem3ConfEntry

portShmem3ConfEntry 1.3.6.1.4.1.326.2.2.1.5.7.1.1
A table entry containing port configuration information for shared memory network modules.
Status: current Access: not-accessible
OBJECT-TYPE    
  PortShmem3ConfEntry  

pShmem3ConfBoard 1.3.6.1.4.1.326.2.2.1.5.7.1.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem3ConfModule 1.3.6.1.4.1.326.2.2.1.5.7.1.1.2
The number of this network module within the switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem3ConfPort 1.3.6.1.4.1.326.2.2.1.5.7.1.1.3
The number of this port within the switch board and network module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem3QsizeforCBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.4
The dedicated queue size in cells for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem3QsizeforVBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.5
The dedicated queue size in cells for nrtVBR (Non-Real-Time Variable Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem3QsizeforABR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.6
The dedicated queue size in cells for ABR (Available Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem3QsizeforUBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.7
The dedicated queue size in cells for UBR (Unspecified Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem3Clp01ThreshforCBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.8
The CLP=0+1 discard threshold in cells for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem3Clp1ThreshforCBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.9
The CLP=1 discard threshold in cells for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem3Clp01ThreshforVBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.10
The CLP=0+1 discard threshold in cells for nrtVBR (Variable Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem3Clp1ThreshforVBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.11
The CLP=1 discard threshold in cells for nrtVBR (Variable Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem3Clp01ThreshforABR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.12
The CLP=0+1 discard threshold in cells for ABR (Available Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem3Clp1ThreshforABR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.13
The CLP=1 discard threshold in cells for ABR (Available Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem3Clp01ThreshforUBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.14
The CLP=0+1 discard threshold in cells for UBR (Unspecified Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem3Clp1ThreshforUBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.15
The CLP=1 discard threshold in cells for UBR (Unspecified Bit Rate) traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem3RateLimit 1.3.6.1.4.1.326.2.2.1.5.7.1.1.16
The number of cells/second to limit this port. This in effect, sets a new logical line rate for this network module. If set to 0, rate-limiting is disabled. (i.e. full bandwidth is returned to the port).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pShmem3ConfSVCSchedulingCBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.17
This variable defines the scheduling discipline that is going to be used to service all CBR SVC connections that are output across this Series-D port. roundrobin: On Series-D netmod, this means that all CBR SVC's will be served only by one of the two round robin queues. smoothed: On Series-D netmod, this means that all CBR SVC's will be served by the rate controller. guaranteed: On Series-D netmod, this means that all CBR SVC's will be served by both the rate controller and the round robin queues.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER roundrobin(2), smoothed(3), guaranteed(4)  

pShmem3ConfPVCSchedulingCBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.18
This variable defines the scheduling discipline that is going to be used to service all CBR PVC connections that are output across this port. Series-D netmods support all three scheduling modes. perupc: This means that each individual CBR PVC will be scheduled based on the discipline associated with the UPC contract used to open the connection. roundrobin: This means that each individual CBR PVC will served only by the rate controller. smoothed: On Series-D netmod, this means that all CBR PVC's will be served only by the rate controller. guaranteed: This means that all CBR PVC's will be served by both the rate controller and the round robin queues.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER perupc(1), roundrobin(2), smoothed(3), guaranteed(4)  

pShmem3ConfSVCSchedulingVBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.19
This variable defines the scheduling discipline that is going to be used to service all VBR SVC connections that are output across this Series-D port. roundrobin: On Series-D netmod, this means that all VBR SVC's will be served only by one of the two round robin queues. smoothed: On Series-D netmod, this means that all VBR SVC's will be served by the rate controller. guaranteed: On Series-D netmod, this means that all VBR SVC's will be served by both the rate controller and the round robin queues.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER roundrobin(2), smoothed(3), guaranteed(4)  

pShmem3ConfPVCSchedulingVBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.20
This variable defines the scheduling discipline that is going to be used to service all VBR PVC connections that are output across this port. Series-D netmods support all three scheduling modes. perupc: This means that each individual VBR PVC will be scheduled based on the discipline associated with the UPC contract used to open the connection. roundrobin: This means that each individual VBR PVC will served only by the rate controller. smoothed: On Series-D netmod, this means that all VBR PVC's will be served only by the rate controller. guaranteed: This means that all VBR PVC's will be served by both the rate controller and the round robin queues.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER perupc(1), roundrobin(2), smoothed(3), guaranteed(4)  

pShmem3ConfAltCLPConfigCBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.21
This vairable defines the per-port configuration for the use of the VC level Alternate CLP Thresholdold on CBR/rtVBR connections. The states mean the following: allOn: All CBR/rtVBR connections use the alt CLP threshold. allOff: No CBR/rtVBR connections use the alt CLP threshold. svcOn: All CBR/rtVBR SVC's will use the alt CLP threshold. For CBR/rtVBR PVC's, whether the alt CLP threshold is used is determined by the presence or absence of the 'altCLPthresh' flag in the UPC contract. svcOff: No CBR/rtVBR SVC's will use the alt CLP threshold. For CBR/rtVBR PVC's, whether the alt CLP threshold is used is determined by the presence or absence of the 'altCLPthresh' flag in the UPC contract.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4)  

pShmem3ConfAltCLPConfigVBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.22
This vairable defines the per-port configuration for the use of the VC level Alternate CLP Thresholdold on nrtVBR connections. The states mean the following: allOn: All nrtVBR connections use the alt CLP threshold. allOff: No nrtVBR connections use the alt CLP threshold. svcOn: All nrtVBR SVC's will use the alt CLP threshold. For nrtVBR PVC's, whether the alt CLP threshold is used is determined by the presence or absence of the 'altCLPthresh' flag in the UPC contract. svcOff: No nrtVBR SVC's will use the alt CLP threshold. For nrtVBR PVC's, whether the alt CLP threshold is used is determined by the presence or absence of the 'altCLPthresh' flag in the UPC contract.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4)  

pShmem3ConfAltCLPConfigUBR 1.3.6.1.4.1.326.2.2.1.5.7.1.1.23
This vairable defines the per-port configuration for the use of the VC level Alternate CLP Thresholdold on UBR connections. The states mean the following: allOn: All UBR connections use the alt CLP threshold. allOff: No UBR connections use the alt CLP threshold. svcOn: All UBR SVC's will use the alt CLP threshold. For UBR PVC's, whether the alt CLP threshold is used is determined by the presence or absence of the 'altCLPthresh' flag in the UPC contract. svcOff: No UBR SVC's will use the alt CLP threshold. For UBR PVC's, whether the alt CLP threshold is used is determined by the presence or absence of the 'altCLPthresh' flag in the UPC contract.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4)  

pShmem3AtmInterfaceIndex 1.3.6.1.4.1.326.2.2.1.5.7.1.1.24
The Atm interface index correspong to this port. This is also the index of the portTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portShmem3Table 1.3.6.1.4.1.326.2.2.1.5.7.2
A table for current state of port on shared memory network modules. Implementation of this table is mandatory if the network module hardware is based on shared memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortShmem3Entry

portShmem3Entry 1.3.6.1.4.1.326.2.2.1.5.7.2.1
A table entry containing current port configuration information for shared memory network modules.
Status: current Access: not-accessible
OBJECT-TYPE    
  PortShmem3Entry  

pShmem3Board 1.3.6.1.4.1.326.2.2.1.5.7.2.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem3Module 1.3.6.1.4.1.326.2.2.1.5.7.2.1.2
The number of this network module within the switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem3Port 1.3.6.1.4.1.326.2.2.1.5.7.2.1.3
The number of this port within the switch board and network module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem3Priority 1.3.6.1.4.1.326.2.2.1.5.7.2.1.4
The traffic type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER priorityABR(1), priorityVBR(2), priorityCBR(3), priorityUBR(4)  

pShmem3CurrentQsize 1.3.6.1.4.1.326.2.2.1.5.7.2.1.5
The current size of the queue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pShmem3TxCells 1.3.6.1.4.1.326.2.2.1.5.7.2.1.6
The number of cells that were transmitted for this port and priority queue.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pShmem3EPDLostCells 1.3.6.1.4.1.326.2.2.1.5.7.2.1.7
The number of cells that were lost for this port and priority queue due to EPD threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pShmem3CLP01LostCells 1.3.6.1.4.1.326.2.2.1.5.7.2.1.8
The number of cells that were lost for this port and priority queue due CLP=0+1 threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pShmem3CLP1LostCells 1.3.6.1.4.1.326.2.2.1.5.7.2.1.9
The number of cells that were lost for this port and priority queue due to CLP=1 threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pShmem3VcCLPLostCells 1.3.6.1.4.1.326.2.2.1.5.7.2.1.10
The number of cells that were lost for this port and priority queue due to per VC CLP=1 and CLP=0+1 thresholds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pShmem3OverflowLostCells 1.3.6.1.4.1.326.2.2.1.5.7.2.1.11
The number of cells that were lost for this port and priority queue due to memory overflows.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pShmem3PPDLostCells 1.3.6.1.4.1.326.2.2.1.5.7.2.1.12
The number of cells that were lost for this port and priority queue due to EPD, per port and per VC CLP, and memory overflows.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

channelShmem3Table 1.3.6.1.4.1.326.2.2.1.5.8.1
A table of information about the channels through this shared memory network module.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ChannelShmem3Entry

channelShmem3Entry 1.3.6.1.4.1.326.2.2.1.5.8.1.1
A table entry containing channel seriesD information.
Status: current Access: not-accessible
OBJECT-TYPE    
  ChannelShmem3Entry  

vcShmem3OutputPort 1.3.6.1.4.1.326.2.2.1.5.8.1.1.1
The value of this object identifies the output port of this channel and is the same as the opathPort, and portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vcShmem3OutputVPI 1.3.6.1.4.1.326.2.2.1.5.8.1.1.2
The value of this object identifies the output VPI (Virtual Path Identifier) of this channel and is the same as the opathVPI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vcShmem3OutputVCI 1.3.6.1.4.1.326.2.2.1.5.8.1.1.3
The output VCI (Virtual Channel Identifier) of this channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vcShmem3IntentionalLostCells 1.3.6.1.4.1.326.2.2.1.5.8.1.1.4
The number of cells on this channel that were dropped due to EPD (Early Packet Discard) or PPD (Partial Packet Discard).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vcShmem3UnintentionalLostCells 1.3.6.1.4.1.326.2.2.1.5.8.1.1.5
The number of cells on this channel that were dropped due to output memory shortages or the CLP (Cell Loss Priority) threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vcShmem3CLP0TxCells 1.3.6.1.4.1.326.2.2.1.5.8.1.1.6
The number of CLP=0 cells on this channel that were transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vcShmem3CLP1TxCells 1.3.6.1.4.1.326.2.2.1.5.8.1.1.7
The number of CLP=1 cells on this channel that were transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vcShmem3EPDLostCells 1.3.6.1.4.1.326.2.2.1.5.8.1.1.8
The number of cells lost on this channel due to EPD.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vcShmem3CLP1LostCells 1.3.6.1.4.1.326.2.2.1.5.8.1.1.9
The number of cells lost on this channel due to CLP=1 threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vcShmem3CLP01LostCells 1.3.6.1.4.1.326.2.2.1.5.8.1.1.10
The number of cells lost on this channel due to CLP=0+1 threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vcShmem3TransmittedPackets 1.3.6.1.4.1.326.2.2.1.5.8.1.1.11
The number of transmitted packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vcShmem3CurrentQsize 1.3.6.1.4.1.326.2.2.1.5.8.1.1.12
The current size of the queue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pathShmem3Table 1.3.6.1.4.1.326.2.2.1.5.8.2
A table of information about the paths through this shared memory network module.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PathShmem3Entry

pathShmem3Entry 1.3.6.1.4.1.326.2.2.1.5.8.2.1
A table entry containing path seriesD information.
Status: current Access: not-accessible
OBJECT-TYPE    
  PathShmem3Entry  

vpShmem3OutputPort 1.3.6.1.4.1.326.2.2.1.5.8.2.1.1
The value of this object identifies the output port of this path and is the same as the portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vpShmem3OutputVPI 1.3.6.1.4.1.326.2.2.1.5.8.2.1.2
The output VPI (Virtual Path Identifier) of this path.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vpShmem3UnintentionalLostCells 1.3.6.1.4.1.326.2.2.1.5.8.2.1.4
The number of cells on this path that were dropped due to output memory shortages or the CLP (Cell Loss Priority) threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vpShmem3CLP0TxCells 1.3.6.1.4.1.326.2.2.1.5.8.2.1.5
The number of CLP=0 cells on this path that were transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vpShmem3CLP1TxCells 1.3.6.1.4.1.326.2.2.1.5.8.2.1.6
The number of CLP=1 cells on this path that were transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vpShmem3CLP1LostCells 1.3.6.1.4.1.326.2.2.1.5.8.2.1.8
The number of cells lost on this path due to CLP=1 threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vpShmem3CLP01LostCells 1.3.6.1.4.1.326.2.2.1.5.8.2.1.9
The number of cells lost on this path due to CLP=0+1 threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vpShmem3TransmittedPackets 1.3.6.1.4.1.326.2.2.1.5.8.2.1.10
The number of transmitted packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vpShmem3CurrentQsize 1.3.6.1.4.1.326.2.2.1.5.8.2.1.11
The current size of the queue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

netmodGenericShmemTable 1.3.6.1.4.1.326.2.2.1.5.9.1
A table for simple network modules. Implementation of this table is optional.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NetmodGenericShmemEntry

netmodGenericShmemEntry 1.3.6.1.4.1.326.2.2.1.5.9.1.1
A table entry containing simple network module configuration information
Status: current Access: not-accessible
OBJECT-TYPE    
  NetmodGenericShmemEntry  

nGenericShmemBoard 1.3.6.1.4.1.326.2.2.1.5.9.1.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nGenericShmemModule 1.3.6.1.4.1.326.2.2.1.5.9.1.1.2
The number of this network module within the switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nGenericShmemSubindex 1.3.6.1.4.1.326.2.2.1.5.9.1.1.3
The subindex of this generic shmem within the network module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nGenericShmemCurrentUcastConnections 1.3.6.1.4.1.326.2.2.1.5.9.1.1.4
The current number of unicast connections active on this network module. If a separate unicast connection space is not supported, this value will be -1.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nGenericShmemCurrentMcastConnections 1.3.6.1.4.1.326.2.2.1.5.9.1.1.5
The current number of multicast connections active on this network module. If a separate multicast connection space is not supported, this value will be -1.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nGenericShmemCurrentConnections 1.3.6.1.4.1.326.2.2.1.5.9.1.1.6
The current number of connections (either multicast or unicast) active on this network module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nGenericShmemMaxUcastConnections 1.3.6.1.4.1.326.2.2.1.5.9.1.1.7
The total number of unicast connections that this network module can support. If a separate unicast connection space is not supported, this value will be -1. The largest possible number of ATM connections can be 2^28 - 1 (i.e., 268435455) since VPI and VCI fields in the ATM cell header occupies a total of 28 bits (12 bits of VPI and 16 bits of VCI). Any value greater than 2^28 - 1 for this MIB will indicate that this network module can support an unlimited number of unicast connections.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nGenericShmemMaxMcastConnections 1.3.6.1.4.1.326.2.2.1.5.9.1.1.8
The total number of multicast connections that this network module can support. If a separate multicast connection space is not supported, this value will be -1. The largest possible number of ATM connections can be 2^28 - 1 (i.e., 268435455) since VPI and VCI fields in the ATM cell header occupies a total of 28 bits (12 bits of VPI and 16 bits of VCI). Any value greater than 2^28 - 1 for this MIB will indicate that this network module can support an unlimited number of multicast connections.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nGenericShmemMaxConnections 1.3.6.1.4.1.326.2.2.1.5.9.1.1.9
The total number of connections (either multicast or unicast) that this network module can support. The largest possible number of ATM connections can be 2^28 - 1 (i.e., 268435455) since VPI and VCI fields in the ATM cell header occupies a total of 28 bits (12 bits of VPI and 16 bits of VCI). Any value greater than 2^28 - 1 for this MIB will indicate that this network module can support an unlimited number of connections.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

netmodGenericShmemCustomBCSTable 1.3.6.1.4.1.326.2.2.1.5.9.3
A table for shared memory custom BCS mappings
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NetmodGenericShmemCustomBCSEntry

netmodGenericShmemCustomBCSEntry 1.3.6.1.4.1.326.2.2.1.5.9.3.1
A table entry containing shared memory custom BCS mappings
Status: current Access: not-accessible
OBJECT-TYPE    
  NetmodGenericShmemCustomBCSEntry  

nGenericShmemCustomBCSBoard 1.3.6.1.4.1.326.2.2.1.5.9.3.1.1
The index of this board within the ATM switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

nGenericShmemCustomBCSModule 1.3.6.1.4.1.326.2.2.1.5.9.3.1.2
The number of this network module within the switch board.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

nGenericShmemCustomBCSSubindex 1.3.6.1.4.1.326.2.2.1.5.9.3.1.3
The subindex of this generic shmem within the network module.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

nGenericShmemCustomBCSValue 1.3.6.1.4.1.326.2.2.1.5.9.3.1.4
The value of this BCS
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

nGenericShmemCustomBCSWeight 1.3.6.1.4.1.326.2.2.1.5.9.3.1.5
The weight assigned to this BCS
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nGenericShmemCustomBCSRowStatus 1.3.6.1.4.1.326.2.2.1.5.9.3.1.6
Administrative status of this entry
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

dualScpConfTable 1.3.6.1.4.1.326.2.2.1.6.1.1
A table for current state of dual SCP configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DualScpConfEntry

dualScpConfEntry 1.3.6.1.4.1.326.2.2.1.6.1.1.1
A table entry containing current dual SCP configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  DualScpConfEntry  

dualScpSlot 1.3.6.1.4.1.326.2.2.1.6.1.1.1.1
The slot number for this SCP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER slotX(1), slotY(2)  

dualScpState 1.3.6.1.4.1.326.2.2.1.6.1.1.1.2
Shows whether the switch is operating with a single or dual SCPs. The value other(3) denotes that both SCPs are present but communication is not yet established.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER standalone(1), dual(2), other(3)  

dualScpSyncState 1.3.6.1.4.1.326.2.2.1.6.1.1.1.3
This variable contains the current state of synchronization.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

dualScpPrimary 1.3.6.1.4.1.326.2.2.1.6.1.1.1.4
Controls which SCP is designated as the primary SCP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER slotX(1), slotY(2)  

dualScpFailover 1.3.6.1.4.1.326.2.2.1.6.1.1.1.5
Disables the dual SCP failover mechanism. When set to disable(2), the backup SCP will not take over if the main SCP goes down.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dualScpManualSyncRequest 1.3.6.1.4.1.326.2.2.1.6.1.1.1.6
This variable can be used to manually synchronize the entire flash or any of the specified files. syncIdle(1) - No synchronization. syncFlash(2) - Synchronize the entire flash. syncCdb(3) - Synchronize the CDB file. syncPassword(4) - Synchronize the password file (depracated). syncLecsConfig(5) - Synchronize the LECS configuration file. syncOS(6) - Synchronize the OS. syncInit(7) - Reformat the entire flash. syncSecurid(8) - Synchronize the securid configuration file. syncSecret(9) - Synchronize the securid node secret file. syncLoader(10) - Synchronize the mini-loader. syncKrb5KeyTab(12)- Synchronize the kerberos v5srvtab file.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER syncIdle(1), syncFlash(2), syncCdb(3), syncPassword(4), syncLecsConfig(5), syncOS(6), syncInit(7), syncSecurid(8), syncSecret(9), syncLoader(10), syncKrb5KeyTab(12)  

dualScpCdbSyncMode 1.3.6.1.4.1.326.2.2.1.6.1.1.1.7
Controls whether CDB synchronization will be manual or automatic.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER manual(1), automatic(2)  

dualScpManualSwitchOver 1.3.6.1.4.1.326.2.2.1.6.1.1.1.8
Forces the backup SCP to take switch control from the main SCP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dualScpSwitchOverTime 1.3.6.1.4.1.326.2.2.1.6.1.1.1.9
Show the time when switch over occurred.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

dualScpSwitchOverThreshold 1.3.6.1.4.1.326.2.2.1.6.1.1.1.10
Amount of time the standby SCP will wait after loss of active SCP's heartbeat before it takes control of the switch. The valid range is 2-300 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

dualScpSyncRequestList 1.3.6.1.4.1.326.2.2.1.6.1.1.1.11
The current list of items that are waiting to be synchronized. This is a bit pattern containing the specified enumurated bits. The bit definitions are: 0x02 -- syncFlash 0x04 -- syncCdb 0x08 -- syncPassword 0x10 -- syncLecsConfig 0x20 -- syncOS 0x40 -- syncInit 0x80 -- syncSecurid 0x100 -- syncSecret 0x200 -- syncLoader 0x800 -- syncKrb5KeyTab
Status: current Access: read-only
OBJECT-TYPE    
  IntegerBitString  

dualScpNumSyncRequests 1.3.6.1.4.1.326.2.2.1.6.1.1.1.12
The number of synchronization requests since this agent was initialized.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dualScpNumSyncFailures 1.3.6.1.4.1.326.2.2.1.6.1.1.1.13
The number of synchronization failures since this agent was initialized.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dualScpResetStandbyScp 1.3.6.1.4.1.326.2.2.1.6.1.1.1.14
Setting this variable to enable(1) resets the backup SCP forcing it to start over.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dualScpAutoRemoveOldFiles 1.3.6.1.4.1.326.2.2.1.6.1.1.1.15
Setting this variable to enable(1) instructs the backup SCP to remove old files during file synchronization in order to make room for the files that are being synchronized. This usually removes older copies of OS files. When synchronizing the OS, the current version of the OS will be removed if there isn't sufficient space for the new OS being synchronized.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dualScpRedundancyState 1.3.6.1.4.1.326.2.2.1.6.1.1.1.16
This variable contains the current state of Dual SCP Redundancy.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

dualScpSVXCPStateSyncPercent 1.3.6.1.4.1.326.2.2.1.6.1.1.1.17
When SVx/SPVx Preservation is enabled, call state information will be transferred from the Active SCP to the Standby SCP, prior to any SCP control transfer. This MIB variable tracks the completion percentage of the information transfer. Before SCP control transfer occurs, the user can query this variable to find out how much of the information transfer has been done.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge 0..100  

dualScpSVXCPStateTransferFailed 1.3.6.1.4.1.326.2.2.1.6.1.1.1.18
When SVx/SPVx Preservation is enabled, call state information will be transferred from the Active SCP to the Standby SCP. The value returned is 'Failed' for any failure in this transfer, 'OK' otherwise.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER failed(1), ok(2)  

dualScpSVXCPdroppedCallCount 1.3.6.1.4.1.326.2.2.1.6.1.1.1.19
SVx/SPVx Preservation has failed to preserve zero or more calls, whose number is given here.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericPortGroupConfTable 1.3.6.1.4.1.326.2.2.1.5.9.2
A table for simple network modules. Implementation of this table is optional.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenericPortGroupConfEntry

genericPortGroupConfEntry 1.3.6.1.4.1.326.2.2.1.5.9.2.1
A table entry containing simple network module configuration information
Status: current Access: not-accessible
OBJECT-TYPE    
  GenericPortGroupConfEntry  

genericPortGroupBoard 1.3.6.1.4.1.326.2.2.1.5.9.2.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericPortGroupIndex 1.3.6.1.4.1.326.2.2.1.5.9.2.1.2
The number of this port group(module) within a switch board. This is the number that identifies the port group within a switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericPortGroupSubindex 1.3.6.1.4.1.326.2.2.1.5.9.2.1.3
The subindex of this port group identifying a port within this port group.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericPortGroupPrioIndex 1.3.6.1.4.1.326.2.2.1.5.9.2.1.4
The priority on the port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericPortGroupAal5PacketDrop 1.3.6.1.4.1.326.2.2.1.5.9.2.1.5
The AAL5 packet drop threshold in percentage of cells. The switch software provides a reasonable default, however, the user may wish to change this value according to the type of traffic and size of packets being transmitted on the network.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericPortGroupEfciOn 1.3.6.1.4.1.326.2.2.1.5.9.2.1.6
The threshold at which the EFCI (Explicit Forward Congestion Indication) bit is turned on for ABR (Available Bit Rate) traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericPortGroupEfciOff 1.3.6.1.4.1.326.2.2.1.5.9.2.1.7
The threshold at which the EFCI (Explicit Forward Congestion Indication) bit is turned off for ABR (Available Bit Rate) traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericPortGroupPrioName 1.3.6.1.4.1.326.2.2.1.5.9.2.1.8
The priority name (CBR, VBR, ABR, UBR) for this priority index.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

genericOutputPortConfTable 1.3.6.1.4.1.326.2.2.1.5.10.1
A table for managing the configurable items for a port in a generic manner. Implementation of this table is optional.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenericOutputPortConfEntry

genericOutputPortConfEntry 1.3.6.1.4.1.326.2.2.1.5.10.1.1
A table entry containing generic port configuration information
Status: current Access: not-accessible
OBJECT-TYPE    
  GenericOutputPortConfEntry  

genericOutputPortConfBoard 1.3.6.1.4.1.326.2.2.1.5.10.1.1.1
The index of this board within the ATM switch
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericOutputPortConfModule 1.3.6.1.4.1.326.2.2.1.5.10.1.1.2
The number of this port group within the switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericOutputPortConfPort 1.3.6.1.4.1.326.2.2.1.5.10.1.1.3
The number identifies the port within a switch board and a port group.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericOutputPortConfPrio 1.3.6.1.4.1.326.2.2.1.5.10.1.1.4
The priority on the output port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericOutputPortConfPrioDedicatedQSize 1.3.6.1.4.1.326.2.2.1.5.10.1.1.5
The dedicated (minimum) queue size, in cells for this pport and priority
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericOutputPortConfPrioClp1Threshold 1.3.6.1.4.1.326.2.2.1.5.10.1.1.6
The CLP=1 discard threshold, in cells for this port and priority.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericOutputPortConfPrioClp01Threshold 1.3.6.1.4.1.326.2.2.1.5.10.1.1.7
The CLP=0+1 discard threshold, in cells for this port and priority.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericOutputPortConfPrioName 1.3.6.1.4.1.326.2.2.1.5.10.1.1.8
The priority name (CBR, VBR, ABR, UBR) for this genericOutputPortIndex on this port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

genericOutputPortConfAtmif 1.3.6.1.4.1.326.2.2.1.5.10.1.1.9
The AtmIf(BNP) of this shmem within the ATM switch
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericOutputPortStatsTable 1.3.6.1.4.1.326.2.2.1.5.10.2
A table for managing Statistics information about the current state of a port in a generic manner. Implementation of this table is optional.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenericOutputPortStatsEntry

genericOutputPortStatsEntry 1.3.6.1.4.1.326.2.2.1.5.10.2.1
A table entry containing generic port configuration information
Status: current Access: not-accessible
OBJECT-TYPE    
  GenericOutputPortStatsEntry  

genericOutputPortStatsBoard 1.3.6.1.4.1.326.2.2.1.5.10.2.1.1
The index of this board within the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericOutputPortStatsModule 1.3.6.1.4.1.326.2.2.1.5.10.2.1.2
The number of this port group within the switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericOutputPortStatsPort 1.3.6.1.4.1.326.2.2.1.5.10.2.1.3
The number of this port within the switch board and the port group.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericOutputPortStatsPrio 1.3.6.1.4.1.326.2.2.1.5.10.2.1.4
The index of this priority.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericOutputPortStatsPrioTransmittedCells 1.3.6.1.4.1.326.2.2.1.5.10.2.1.5
The number of cells transmitted on this port for this priority
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

genericOutputPortStatsPrioClp1LostCells 1.3.6.1.4.1.326.2.2.1.5.10.2.1.6
The number of cells lost on this port for this priority due to CLP=1 threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

genericOutputPortStatsPrioClp01LostCells 1.3.6.1.4.1.326.2.2.1.5.10.2.1.7
The number of cells lost on this port for this priority due to CLP=0+1 threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

genericOutputPortStatsPrioName 1.3.6.1.4.1.326.2.2.1.5.10.2.1.8
The priority name (CBR, VBR, ABR, UBR) for this genericOutputPortIndex on this port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

genericOutputPortStatsAtmif 1.3.6.1.4.1.326.2.2.1.5.10.2.1.9
The index of Atmif associated with this shmem in the ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

genericOutputPortStatsPrioEpdPpdLostCells 1.3.6.1.4.1.326.2.2.1.5.10.2.1.10
The number of cells lost on this port for this priority due to EPD/PPD threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hardwareVersion 1.3.6.1.4.1.326.2.2.2.1.1.1
The version of the ATM switch hardware in hex. The version number 0x1 is revision A, 0x2 is revision B etc. Version number 0x0 represents an unknown type.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

softwareVersion 1.3.6.1.4.1.326.2.2.2.1.1.2
The version of the ATM switch control software in hex. The version number is encoded into 6 hex digits. For example, version 1.2.3 is encoded as 0x010203.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

maxPaths 1.3.6.1.4.1.326.2.2.2.1.1.3
The maximum number of input VPIs (Virtual Path Identifies).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

maxChannels 1.3.6.1.4.1.326.2.2.2.1.1.4
The maximum number of input VCIs (Virtual Channel Identifiers).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

atmAddress 1.3.6.1.4.1.326.2.2.2.1.1.5
The address of this ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  SpansAddress  

uptime 1.3.6.1.4.1.326.2.2.2.1.1.6
The length of time this ATM switch has been up, in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

switchCDV 1.3.6.1.4.1.326.2.2.2.1.1.7
The switch Cell Delay Variation (CDV) specified in microseconds, indicates the time window in which a cell may be received on a connection and be accepted. A cell that is received on a connection outside the CDV window will be tagged or dropped as indicated by the switchPolicingAction object. The switchCDV is the default CDV for all the connections on this switch. Individual connections can be set to explicitly override this value.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32  

switchPolicingAction 1.3.6.1.4.1.326.2.2.2.1.1.8
This object indicates the action the switch will take in case of bandwidth violation. The switchPolicingAction is the default policing action for all the connections on this switch. Individual connections can be set to explicitly override this default action.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER tag(1), drop(2)  

softwareVersionText 1.3.6.1.4.1.326.2.2.2.1.1.9
The version of the ATM switch control software. This object provides text information about the internal software configuration that was used when the switch control software was built.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

switchType 1.3.6.1.4.1.326.2.2.2.1.1.10
This object identifies the switch type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER asx100(1), asx200(2), asx200wg(4), asx200bx(5), asx200bxe(6), cabletron9A000(7), asx1000(8), le155(9), sfcs200wg(10), sfcs200bx(11), sfcs1000(12), tnx210(15), tnx1100(16), asx1200(17), asx4000(18), le25(19), esx3000(20), asx150(22)  

switchReservedPMPMinVCI 1.3.6.1.4.1.326.2.2.2.1.1.12
The minimum VCI that is reserved for PMP connections.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

switchReservedPMPMaxVCI 1.3.6.1.4.1.326.2.2.2.1.1.13
The maximum VCI that is reserved for PMP connections.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

switchTimeZone 1.3.6.1.4.1.326.2.2.2.1.1.14
The TimeZone configured for this ATM switch. This variable follows the POSIX standard 1003.1-1988 for the format of the TZ environment variable. In particular, it is general enough to specify the rules for converting from Standard to Daylight Savings time for most timezones of the world. By default, the switch has the rules built in for the following timezones: EST5EDT CST6CDT MST7MDT PST8PDT AKST9AKDT. Locales outside of these timezones will need to supply the appropriate rule for switching between Daylight and Standard time.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

switchGMTime 1.3.6.1.4.1.326.2.2.2.1.1.15
The switch's notion of Greenwich Mean Time. Linked to hrSystemDate. Offset part of time spec, if supplied, is considered an error.
Status: current Access: read-write
OBJECT-TYPE    
  DateAndTime  

switchProtocolType 1.3.6.1.4.1.326.2.2.2.1.1.16
The transfer protocol that is used when upgrading the switch software, backing up the CDB, etc.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER tftp(1), ftp(2)  

switchCurrentUserid 1.3.6.1.4.1.326.2.2.2.1.1.17
The value of this object identifies the user currently logged in or attempting to log in on the switch. It would be a NULL string if no one is logged in currently.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

switchCurrentLoginFrom 1.3.6.1.4.1.326.2.2.2.1.1.18
This string gives the IP address of the host from where the current user is logged in or attempting to log in. A NULL string is returned if no one is currently logged in on the switch. If its a serial port login, the string indicates the same
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

switchPrimaryClock 1.3.6.1.4.1.326.2.2.2.1.1.19
The port number whose 8KHz clock is used as primary clock by all the netmods on all the boards in this switch.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

switchSecondaryClock 1.3.6.1.4.1.326.2.2.2.1.1.20
The port number whose 8KHz clock is used as secondary clock by all the netmods on all the boards in this switch.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

switchClockOperStatus 1.3.6.1.4.1.326.2.2.2.1.1.21
The currently active 8KHz clock configuration. The crystal?Clock types are not currently used. The default mode is localCrystalClock which means each netmod runs off of its own crystal. If primary, secondary or tcm clocking is configured then the status will be updated by switch software accordingly.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER primaryClock(1), secondaryClock(2), crystalAClock(3), crystalBClock(4), crystalCClock(5), crystalDClock(6), tcmClock(7), localCrystalClock(8), primaryClockPartner(9), secondaryClockPartner(10)  

switchTimingMode 1.3.6.1.4.1.326.2.2.2.1.1.22
The timing mode in which the switch is running. switchMode(1) provides for the direct use of any port recovered clock from any timing-capable network module in the switch. tcmMode(3) uses the clock provided by the CEC-Plus' Timing Control Modules (TCM).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER switchMode(1), tcmMode(3)  

switchConnectionPreservation 1.3.6.1.4.1.326.2.2.2.1.1.23
When connection preservation is enabled the switch will not reset the hardware when a fail-over or software-reboot occurs. The software will preserve existing PVC connections and re-create other connections. This prevents cell traffic on PVC connections from being disrupted during the fail-over / software-reboot process. When connection preservation is disabled the switch will reset the hardware when a fail-over or software-reboot occurs. All connections will then be re-created. Cell traffic on all connections will be disrupted during the fail-over / software-reboot process. This is disabled by default on all asx200bx based switches. On all the other platforms, this is enabled by default.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

switchATMLayerOAM 1.3.6.1.4.1.326.2.2.2.1.1.24
This object specifies whether the processing of ATM layer OAM cells by this switch is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

switchHttpServer 1.3.6.1.4.1.326.2.2.2.1.1.25
This specifies whether the embedded HTTP Server (which is used for the element manager) is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

switchHttpHelpUrl 1.3.6.1.4.1.326.2.2.2.1.1.26
This specifies the URL path for the local depository of the WWW help pages for the web-based element manager on the switch. The URL is in the form: [:port][] For example: 1.2.3.4:8000/usr/fore/www This includes the IP address host to contact, and optionally the port on that host, and the directory on that host where the help pages were saved. If an empty string, the switch will use a default location on FORE's external web site.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

switchCtrlLinkid 1.3.6.1.4.1.326.2.2.2.1.1.28
The linkid of the ctrl port on this switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

switchClockCurrentStatus 1.3.6.1.4.1.326.2.2.2.1.1.29
The currently active 8KHz clock configuration. The value would indicate primary Clock or secondary Clock or if neither is available a crystal Clock is determined by the switch control software. The software chooses the lowest netmod number with timing support
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

softwareLicenseKey 1.3.6.1.4.1.326.2.2.2.1.1.31
The software license key of this switch.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

switchCounterResetTime 1.3.6.1.4.1.326.2.2.2.1.1.32
Indicates when all switch (except for virtual connection) counters were reset. The TimeStamp is equal to the sysUpTime when the reset occurred. If switch counters have never been reset, the switchCounterResetTime will be zero. This variable is updated whenever switchCounterReset is written.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

switchCounterReset 1.3.6.1.4.1.326.2.2.2.1.1.33
Writing a value of resetRequest will result in a reset of all counters on the switch except for VCC indexed counters. Writing a value of unresetRequest will destroy all counter offsets and restore counter values to what has accumulated over the sysUpTime period. A response value of resetTrue indicates a resetRequest succeeded and is in effect. A response of resetFalse indicates a reset is not currently in effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER resetRequest(1), unresetRequest(2), resetTrue(3), resetFalse(4)  

switchPrimaryClockPort 1.3.6.1.4.1.326.2.2.2.1.1.35
The name of the hardware port whose 8KHz clock is used as primary clock by all the netmods on all the boards in this switch.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..5)  

switchSecondaryClockPort 1.3.6.1.4.1.326.2.2.2.1.1.36
The name of the hardware port whose 8KHz clock is used as secondary clock by all the netmods on all the boards in this switch.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..5)  

switchPmpEnable 1.3.6.1.4.1.326.2.2.2.1.1.38
Disabling the PMP Feature disallows any point to multipoint connections. The services which require point to multi point connections also need to be disabled. By default the feature is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

switchCallPreservation 1.3.6.1.4.1.326.2.2.2.1.1.39
When SVx/SPVx Preservation is enabled, existing switched connections will be preserved during transfers of switch control from the Active SCP to the Standby SCP, whether user-initiated or due to SCP failure. Cell traffic is preserved during the failover/switchover process. When SVx/SPVx Preservation is disabled, and if Connection Preservation also is disabled, control transfers from the Active SCP to the Standby SCP will reset the switch hardware without having preserved the necessary call-state information. Hence, all switched connections will be cleared and will then have to be recreated. Cell traffic on all switched connections will be disrupted. By default, this feature is disabled on all supported dual-scp platforms.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

switchCallPresOperStatus 1.3.6.1.4.1.326.2.2.2.1.1.40
When SVx/SPVx Preservation is enabled administratively, the feature nevertheless may be disabled operationally (e.g., because of hardware failures, like a missing Standby SCP). When it is operationally disabled, the effect is as though SVx/SPVx Preservation were disabled administratively.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

switchDebounceTable 1.3.6.1.4.1.326.2.2.2.1.1.30
A table, where each entry consists of debounce information associated with a unique port. This information includes the hysteresis value (a positive number in ms) for that port, i.e, the number of ms for which a physical-level failure persists for that port, after which the connection will be brought down
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwitchDebounceEntry

switchDebounceEntry 1.3.6.1.4.1.326.2.2.2.1.1.30.1
A table entry containing physical interface debounce information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwitchDebounceEntry  

switchDebounceIndex 1.3.6.1.4.1.326.2.2.2.1.1.30.1.1
The index value for this entry - ties in with a unique port
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

switchDebounceName 1.3.6.1.4.1.326.2.2.2.1.1.30.1.2
The persistent name of this interface - (the port name)
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

switchDebounceHysteresis 1.3.6.1.4.1.326.2.2.2.1.1.30.1.3
The hysteresis value for this interface. The hysteresis value is the number of ms for which a physical-level failure persists for that interface, after which the connection will be brought down
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

mcastGroup 1.3.6.1.4.1.326.2.2.2.1.1.27
OBJECT IDENTIFIER    

mcastSpaceTable 1.3.6.1.4.1.326.2.2.2.1.1.27.1
A table containing information on number of multicast connections supported on this switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McastSpaceEntry

mcastSpaceEntry 1.3.6.1.4.1.326.2.2.2.1.1.27.1.1
A table entry containing multicast space information
Status: current Access: not-accessible
OBJECT-TYPE    
  McastSpaceEntry  

mcastSpaceIndex 1.3.6.1.4.1.326.2.2.2.1.1.27.1.1.1
Index of this multicast space entry. This value is used to set boardMcastIndex value.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

mcastSpaceNumConn 1.3.6.1.4.1.326.2.2.2.1.1.27.1.1.2
Number of multicast connections that this entry represents. When boardMcastIndex is set to mcastSpaceIndex value, the corresponding board will support mcastSpaceNumConn number of multicast connections.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mcastSpaceName 1.3.6.1.4.1.326.2.2.2.1.1.27.1.1.3
Name of this multicast space entry.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

switchSbprServerAddressTable 1.3.6.1.4.1.326.2.2.2.1.1.34
A table, where each entry consists of a static list of 5 bootp address entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwitchSbprServerAddressEntry

switchSbprServerAddressEntry 1.3.6.1.4.1.326.2.2.2.1.1.34.1
A bootp Ip Address server entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwitchSbprServerAddressEntry  

sbprServerAddressIndex 1.3.6.1.4.1.326.2.2.2.1.1.34.1.1
A unique value greater then zero used as an index into the bootp address table.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sbprServerAddressIndexName 1.3.6.1.4.1.326.2.2.2.1.1.34.1.2
Name of the Interface index into the bootp address table.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

sbprServerMaxHops 1.3.6.1.4.1.326.2.2.2.1.1.34.1.3
The maximum number of hops that a BOOTREQUEST message is permitted to traverse before it must be discarded. Received BOOTREQUEST messages that have a hopcount greater than this value are discarded by this relay agent. The default value is 4.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16  

sbprServerMinSeconds 1.3.6.1.4.1.326.2.2.2.1.1.34.1.4
The minimum number of seconds that a BOOTP client must have been attempting to boot before the relay agent will relay BOOTREQUESTs from that client. The default value is 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

sbprServerAddress1 1.3.6.1.4.1.326.2.2.2.1.1.34.1.5
The IP address of the BOOTP server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sbprServerAddress2 1.3.6.1.4.1.326.2.2.2.1.1.34.1.6
The IP address of the BOOTP server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sbprServerAddress3 1.3.6.1.4.1.326.2.2.2.1.1.34.1.7
The IP address of the BOOTP server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sbprServerAddress4 1.3.6.1.4.1.326.2.2.2.1.1.34.1.8
The IP address of the BOOTP server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sbprServerAddress5 1.3.6.1.4.1.326.2.2.2.1.1.34.1.9
The IP address of the BOOTP server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sbprServerRowStatus 1.3.6.1.4.1.326.2.2.2.1.1.34.1.10
Administrative status of this entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

serviceCategoryTable 1.3.6.1.4.1.326.2.2.2.1.1.37
A table of ATM service categories supported.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ServiceCategoryEntry

serviceCategoryEntry 1.3.6.1.4.1.326.2.2.2.1.1.37.1
A table entry containing ATM Service Category information.
Status: current Access: not-accessible
OBJECT-TYPE    
  ServiceCategoryEntry  

serviceCategoryIndex 1.3.6.1.4.1.326.2.2.2.1.1.37.1.1
The ATM service category index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

serviceCategoryName 1.3.6.1.4.1.326.2.2.2.1.1.37.1.2
The name of the ATM service category. The following values are supported: serviceCategoryIndex serviceCategoryName ----------------- ---------------------- 1 CBR 2 rtVBR 3 nrtVBR 4 ABR 5 UBR
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

confTopoHelloInterval 1.3.6.1.4.1.326.2.2.2.1.11.1
This is the time interval in milli seconds between successive Hello Indication messages sent by SPANS
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

confTopoNsapIndInterval 1.3.6.1.4.1.326.2.2.2.1.11.2
This is the time interval in milli seconds between successive NSAP Indication messages sent by SPANS
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

confTopoStaticUpdateInterval 1.3.6.1.4.1.326.2.2.2.1.11.3
This is the time interval in milli seconds between successive refreshes of NSAP static routes in the NSAP topology
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

confTopoMaxHopCount 1.3.6.1.4.1.326.2.2.2.1.11.4
This is the upper limit on the number of hops in the source routes computed by the NSAP router
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

confTopoACRPropMult 1.3.6.1.4.1.326.2.2.2.1.11.5
This is the proportional multiplier expressed as a percentage of Available Cell Rate (ACR). If the percentage change of the ACR of any given link in the NSAP topology exceeds this threshold, then the change is deemed significant
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

confTopoMinThresh 1.3.6.1.4.1.326.2.2.2.1.11.6
This is the capacity value in Cells per second of the minimum value that the threshold value for determining the significant change can take. This minimum value is used to ensure that the threshold for determining significant changes to ACR does not become a very small value in cases where product of the ACR and the proportional multiplier is a very small number.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

confTopoMinVCAvail 1.3.6.1.4.1.326.2.2.2.1.11.7
This is the minimum number of VCs that should be available on a link before the state of the link changes from VCs-not- available to VCs-available. This state is propagated in the link state information. The state changes from VCs-available to VCs-not-available when the number of VCs available becomes zero from a non-zero value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

confTopoSpansAreaID 1.3.6.1.4.1.326.2.2.2.1.11.8
This is the ID of the Area in the SPANS routing hierarchy to which this switch belongs. This number goes into the most significant byte of the SPANS ATM address
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

confTopoSpansBorderSwitch 1.3.6.1.4.1.326.2.2.2.1.11.9
This variable indicates wherher this switch is configured to operate as a SPANS-NNI Border Switch or not
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

confTopoSwitchPrefix 1.3.6.1.4.1.326.2.2.2.1.11.10
The default NSAP (Network Service Access Point) prefix for this ATM switch. The NSAP prefix will be used in the ILMI address registration message as well as the 'hello-indication' SPANS-NNI message.
Status: current Access: read-write
OBJECT-TYPE    
  NsapPrefix  

confTopoSwitchPrefixMask 1.3.6.1.4.1.326.2.2.2.1.11.11
This mask gives the number of leading bits in the above prefix to be used to aggregate the addresses that belong to the switch in SPANS-PNNI alias FORE-PNNI
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

confTopoPeerGroupMask 1.3.6.1.4.1.326.2.2.2.1.11.12
This mask gives the number of the leading bits in the above prefix to be used to aggregate the addresses that belong to the peer group containing this switch in SPANS-PNNI alias FORE-PNNI
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

confTopoSpansPnniBorderSwitch 1.3.6.1.4.1.326.2.2.2.1.11.13
This variable indicates whether this switch is configured to operate as a SPANS-PNNI Border Switch or not
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

confTopoPGSNReachCost 1.3.6.1.4.1.326.2.2.2.1.11.14
This is used to indicate cost of link from border node to PGSN
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4294967295  

confTopoPGSNReachCostMethod 1.3.6.1.4.1.326.2.2.2.1.11.15
This variable indicates the method of computing cost of link from border node to PGSN
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(1), user(2)  

confTopoFtPnniForeArea 1.3.6.1.4.1.326.2.2.2.1.11.16
This variable is the area ID of the FT-PNNI autonomous system in the global fore hierarchy of PNNI and FT-PNNI peergroups
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

confTopoFtPnniForeLevel 1.3.6.1.4.1.326.2.2.2.1.11.17
This variable is the level of the FT-PNNI autonomous system in the global fore hierarchy of PNNI and FT-PNNI peergroups
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

confTopoLBUbrLoadBalance 1.3.6.1.4.1.326.2.2.2.1.11.18
This variable indicates whether this switch is to do Load Balanced UBR routing
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

numberOfPorts 1.3.6.1.4.1.326.2.2.2.1.2.1
The number of ports on this ATM switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portTable 1.3.6.1.4.1.326.2.2.2.1.2.2
A table of information about the ports on this ATM switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortEntry

portEntry 1.3.6.1.4.1.326.2.2.2.1.2.2.1
A table entry containing port information.
Status: current Access: not-accessible
OBJECT-TYPE    
  PortEntry  

portNumber 1.3.6.1.4.1.326.2.2.2.1.2.2.1.1
The value of this object identifies the port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portAdminStatus 1.3.6.1.4.1.326.2.2.2.1.2.2.1.2
The desired state of this port. The up(3) state indicates that SPANS (Simple Protocol for ATM Network Signalling), FORE's link signalling protocol, is used to determine the operational status of the port. The down(2) state dictates that the operational status of the port should not be determined by SPANS.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER down(2), up(3)  

portOperStatus 1.3.6.1.4.1.326.2.2.2.1.2.2.1.3
The current operational state of this port, as determined either by administrative action, when the value of portAdminStatus is down(2), or by SPANS (Simple Protocol for ATM Network Signalling), FORE's link signalling protocol, when the value of porAdminStatus is up(3). For FRAM netmod, it is equivalent to the ifOperStatus of the same port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

portTime 1.3.6.1.4.1.326.2.2.2.1.2.2.1.4
The length of time this port has been in its current state, in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

portRemoteAtmAddress 1.3.6.1.4.1.326.2.2.2.1.2.2.1.5
The ATM address of the entity connected to this port.
Status: current Access: read-only
OBJECT-TYPE    
  SpansAddress  

portRemoteIpAddress 1.3.6.1.4.1.326.2.2.2.1.2.2.1.6
The IP address of the entity connected to this port.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

portMaxPathsIn 1.3.6.1.4.1.326.2.2.2.1.2.2.1.7
The maximum number of incoming virtual paths supported by this port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portNumPathsIn 1.3.6.1.4.1.326.2.2.2.1.2.2.1.8
The number of incoming virtual paths on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

portMaxBandwidthIn 1.3.6.1.4.1.326.2.2.2.1.2.2.1.9
The maximum incoming bandwidth of this port, in cells per second.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portAllocBandwidthIn 1.3.6.1.4.1.326.2.2.2.1.2.2.1.10
The allocated incoming bandwidth of this port, in cells per second.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

portUsedBandwidthIn 1.3.6.1.4.1.326.2.2.2.1.2.2.1.11
The incoming bandwidth being used on this port, in cells per second.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Gauge32  

portReceivedCells 1.3.6.1.4.1.326.2.2.2.1.2.2.1.12
The number of cells received on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

portMaxPathsOut 1.3.6.1.4.1.326.2.2.2.1.2.2.1.13
The maximum number of outgoing virtual paths supported by this port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portNumPathsOut 1.3.6.1.4.1.326.2.2.2.1.2.2.1.14
The number of outgoing virtual paths on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

portMaxBandwidthOut 1.3.6.1.4.1.326.2.2.2.1.2.2.1.15
The maximum outgoing bandwidth of this port, in cells per second.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portAllocBandwidthOut 1.3.6.1.4.1.326.2.2.2.1.2.2.1.16
The allocated outgoing bandwidth of this port, in cells per second.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

portUsedBandwidthOut 1.3.6.1.4.1.326.2.2.2.1.2.2.1.17
The outgoing bandwidth being used on this port, in cells per second.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Gauge32  

portTransmittedCells 1.3.6.1.4.1.326.2.2.2.1.2.2.1.18
The number of cells transmitted on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

portHwBoard 1.3.6.1.4.1.326.2.2.2.1.2.2.1.19
The hardware board number of this port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portHwModule 1.3.6.1.4.1.326.2.2.2.1.2.2.1.20
The hardware module number of this port. For a control port (a software port), the value of this object is the maximun number of hardware modules plus one.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portHwNumber 1.3.6.1.4.1.326.2.2.2.1.2.2.1.21
The hardware port number of this port. For a control port (a software port), the value of this object is 0.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

portILMIRemoteIpAddress 1.3.6.1.4.1.326.2.2.2.1.2.2.1.22
The IP address of the entity connected to this port that was discovered using ILMI on path 0. If there is no q2931 siganlling path on VPI 0 that uses ILMI, the value of this object is 255.255.255.255.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

portCDVT 1.3.6.1.4.1.326.2.2.2.1.2.2.1.23
The Cell Delay Variation Tolerance associated with this physical port. Connections take their default value for CDVT from the input side port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

portInputPolicingStatus 1.3.6.1.4.1.326.2.2.2.1.2.2.1.24
The state of policing on this input port. Enabled(1) forces every connection on this input port to be policed. Disabled(2) turns policing off for every connection on this input port. The functions of this variable have been subsumed by the new GCRAPolicingCBR and GCRAPolicingVBR variables below. Now, writing 'disabled' to this MIB variable has the effect of setting GCRAPolicingCBR=allOff and GCRAPolicingVBR=allOff. On read, this variable reports 'enabled', if either of the GCRAPolicing*BR options are in an 'On' setting. Use of this variable should be avoided, in favor of the two GCRA variables.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

portVbrOverbooking 1.3.6.1.4.1.326.2.2.2.1.2.2.1.25
The percentage of overbooking for nrtVBR connections. The default value is 100 (no overbooking).
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 1..32767  

portVbrBufferOverb 1.3.6.1.4.1.326.2.2.2.1.2.2.1.26
The percentage of buffer overbooking for nrtVBR connections. The default value is 100 (no overbooking).
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 1..32767  

portManagementStatus 1.3.6.1.4.1.326.2.2.2.1.2.2.1.27
The visibility of this port in the management station's view. The default value is 1 (managed).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER managed(1), un-managed(2)  

portAISRDIGeneration 1.3.6.1.4.1.326.2.2.2.1.2.2.1.28
The port ATM layer AIS and RDI generation status.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

portGCRAPolicingCBR 1.3.6.1.4.1.326.2.2.2.1.2.2.1.33
This variable defines the per-port policing configuration for CBR connections. The states mean the following: allOn: ALL CBR connections arriving on this port will be subjected to GCRA policing. allOff: NO CBR connections arriving on this port will be subjected to GCRA policing. svcOn: ALL CRB SVCs arriving on this port will be subjected to GCRA policing svcOff: NO CBR SVCs arriving on this port will be subjected to GCRA policing. CBR PVCs will be GCRA policed based on the state of their UPC contract. default: ALL CBR UNI SVCs/SVPs arriving at this port will be subject to GCRA policing and NO CBR NNI SVCs/SVPs arriving at this port will be subject to GCRA policing. CBR PVCs/PVPs arriving at this port will be policed based on the state of their UPC contract.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4), default(5)  

portGCRAPolicingVBR 1.3.6.1.4.1.326.2.2.2.1.2.2.1.34
This variable defines the per-port policing configuration for nrtVBR connections. The states mean the following: allOn: ALL nrtVBR connections arriving on this port will be subjected to GCRA policing. allOff: NO nrtVBR connections arriving on this port will be subjected to GCRA policing. svcOn: ALL nrtVBR SVCs arriving on this port will be subjected to GCRA policing svcOff: NO nrtVBR SVCs arriving on this port will be subjected to GCRA policing. nrtVBR PVCs will be GCRA policed based on the state of their UPC contract. default: ALL nrtVBR UNI SVCs/SVPs arriving at this port will be subject to GCRA policing and NO nrtVBR NNI SVCs/SVPs arriving at this port will be subject to GCRA policing. nrtVBR PVCs/PVPs arriving at this port will be policed based on the state of their UPC contract.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4), default(5)  

portAAL5PacketDiscardCBR 1.3.6.1.4.1.326.2.2.2.1.2.2.1.35
This variable defines the per-port AAL5 packet discard configuration for CBR connections. The states mean the following: allOn: All CBR AAL5 connections have packet discard performed on them. allOff: AAL5 packet discard is not performed on any CBR connections. svcOn: Any CBR SVC that 'requests' packet discard will have it performed. For CBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection. svcOff: AAL5 packet discard is not performed on any CBR SVC's.For CBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4)  

portAAL5PacketDiscardVBR 1.3.6.1.4.1.326.2.2.2.1.2.2.1.36
This variable defines the per-port AAL5 packet discard configuration for nrtVBR connections. The states mean the following: allOn: All nrtVBR AAL5 connections have packet discard performed on them. allOff: AAL5 packet discard is not performed on any nrtVBR connections. svcOn: Any nrtVBR SVC that 'requests' packet discard will have it performed. For nrtVBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection. svcOff: AAL5 packet discard is not performed on any nrtVBR SVC's.For nrtVBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4)  

portAAL5PacketDiscardUBR 1.3.6.1.4.1.326.2.2.2.1.2.2.1.37
This variable defines the per-port AAL5 packet discard configuration for UBR connections. The states mean the following: allOn: All UBR AAL5 connections have packet discard performed on them. allOff: AAL5 packet discard is not performed on any UBR connections. svcOn: Any UBR SVC that 'requests' packet discard will have it performed. For UBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection. svcOff: AAL5 packet discard is not performed on any UBR SVC's.For UBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4)  

portInputCACErrors 1.3.6.1.4.1.326.2.2.2.1.2.2.1.38
The number of input CAC (Call Admission Control) failures on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

portInputVPIErrors 1.3.6.1.4.1.326.2.2.2.1.2.2.1.39
The number of input VPI allocation failures on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

portInputVCIErrors 1.3.6.1.4.1.326.2.2.2.1.2.2.1.40
The number of input VCI allocation failures on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

portInputSetupErrors 1.3.6.1.4.1.326.2.2.2.1.2.2.1.41
The number of input connection setup failures on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

portOutputCACErrors 1.3.6.1.4.1.326.2.2.2.1.2.2.1.42
The number of output CAC (Call Admission Control) failures on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

portOutputVPIErrors 1.3.6.1.4.1.326.2.2.2.1.2.2.1.43
The number of output VPI allocation failures on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

portOutputVCIErrors 1.3.6.1.4.1.326.2.2.2.1.2.2.1.44
The number of output VCI allocation failures on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

portOutputSetupErrors 1.3.6.1.4.1.326.2.2.2.1.2.2.1.45
The number of output connection setup failures on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

portPPPolicingCBR 1.3.6.1.4.1.326.2.2.2.1.2.2.1.46
This variable defines the per-port AAL5 Partial Packet Policing configuration for CBR connections. The states of this variable mean the following: allOn: All CBR AAL5 connections have partial packet policing performed on them. allOff: AAL5 partial packet policing is not performed on any CBR connections. svcOn: Any CBR SVC that uses AAL5 will have partial packet policing performed on it. For CBR PVC's, partial packet policing will be performed based on the UPC contract of the connection. svcOff: Partial packet policing will not be performed on any CBR SVC's. For CBR PVC's, partial packet policing is enabled based on the UPC contract of the connection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4)  

portPPPolicingVBR 1.3.6.1.4.1.326.2.2.2.1.2.2.1.47
This variable defines the per-port AAL5 Partial Packet Policing configuration for nrtVBR connections. The states of this variable mean the following: allOn: All nrtVBR AAL5 connections have partial packet policing performed on them. allOff: AAL5 partial packet policing is not performed on any nrtVBR connections. svcOn: Any nrtVBR SVC that uses AAL5 will have partial packet policing performed on it. For nrtVBR PVC's, partial packet policing will be performed based on the UPC contract of the connection. svcOff: Partial packet policing will not be performed on any nrtVBR SVC's. For nrtVBR PVC's, partial packet policing is enabled based on the UPC contract of the connection.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4)  

portUBRTagging 1.3.6.1.4.1.326.2.2.2.1.2.2.1.48
This variable defines the per-port configuration for tagging (setting CLP=1) of all cells on UBR connections. The states of this variable mean the following: allOn: All UBR connections will be tagged. allOff: No UBR connections will be subject to tagging. svcOn: All UBR SVC's will be tagged. UBR PVC's will be tagged based on their UPC contract. svcOff: No UBR SVC's will be tagged. UBR PVC's will be tagged based on their UPC contract.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4)  

portInputCdv 1.3.6.1.4.1.326.2.2.2.1.2.2.1.49
The current value of Cell Delay Variation attributed to the input side of this port, which can be either a user specified value or the system default, as determined by the setting of portInputCdvMode.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

portInputMaxctd 1.3.6.1.4.1.326.2.2.2.1.2.2.1.50
This variable give the maximum Cell Transfer Delay that is being attributed to the input side of this port. The value can be either user specified or a hardware dependant system default value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

portInputDelayMode 1.3.6.1.4.1.326.2.2.2.1.2.2.1.51
This variable controls whether the Cell Delay Variation and Maximum Cell Transfer Delay values attributed to the input side of this port are based on a user defined value or the hardware dependant system default values.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER systemDefault(1), userSpecified(2)  

portOutputCdv 1.3.6.1.4.1.326.2.2.2.1.2.2.1.52
If portOutputDelayMode == userSpecified then this variable contains the constant amount of Cell Delay Variation that is being attributed to this output port. If portOutputDelayMode == systemDefault then an actual value for the Cell Delay Variation experienced by connections traversing this port is being calculated. In this case the value of this variable is meaningless since CDV can only be calculated on a per-connection basis.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

portOutputMaxctd 1.3.6.1.4.1.326.2.2.2.1.2.2.1.53
This variable gives the maximum Cell Transfer Delay that is being attributed to the output side of this port. The value can be either user specified or a hardware dependant system default value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

portOutputDelayMode 1.3.6.1.4.1.326.2.2.2.1.2.2.1.54
This variable controls whether the Cell Delay Variation value contributed by the input side of this port is based on a user defined value or the system default value.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER systemDefault(1), userSpecified(2)  

portCACStatus 1.3.6.1.4.1.326.2.2.2.1.2.2.1.59
The enforcement state of call admission control. The default is enabled(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

portCounterResetTime 1.3.6.1.4.1.326.2.2.2.1.2.2.1.60
Indicates when this port's counters were reset. The TimeStamp is equal to moduleUptime when the reset occurred. If this ports counters were never reset, portCounterResetTime will be zero. This variable is updated whenever portCounterReset or switchCounterReset is written.
Status: deprecated Access: read-only
OBJECT-TYPE    
  TimeStamp  

portCounterReset 1.3.6.1.4.1.326.2.2.2.1.2.2.1.61
Writing a value of resetRequest will result in a reset of all counters on this port. VCC indexed counters are excluded. A response value of resetTrue indicates a resetRequest has succeeded and is currently in effect. A response value of resetFalse indicates a reset is not currently in effect.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER resetRequest(1), resetTrue(3), resetFalse(4)  

portName 1.3.6.1.4.1.326.2.2.2.1.2.2.1.62
The name of this port (BNP format or otherwise).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

portGCRAPolicingRTVBR 1.3.6.1.4.1.326.2.2.2.1.2.2.1.64
This variable defines the per-port policing configuration for rtVBR connections. The states mean the following: allOn: ALL rtVBR connections arriving on this port will be subjected to GCRA policing. allOff: NO rtVBR connections arriving on this port will be subjected to GCRA policing. svcOn: ALL rtVBR SVCs arriving on this port will be subjected to GCRA policing svcOff: NO rtVBR SVCs arriving on this port will be subjected to GCRA policing. rtVBR PVCs will be GCRA policed based on the state of their UPC contract. default: ALL rtVBR UNI SVCs/SVPs arriving at this port will be subject to GCRA policing and NO rtVBR NNI SVCs/SVPs arriving at this port will be subject to GCRA policing. rtVBR PVCs/PVPs arriving at this port will be policed based on the state of their UPC contract.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4), default(5)  

portGCRAPolicingNRTVBR 1.3.6.1.4.1.326.2.2.2.1.2.2.1.65
This variable defines the per-port policing configuration for nrtVBR connections. The states mean the following: allOn: ALL nrtVBR connections arriving on this port will be subjected to GCRA policing. allOff: NO nrtVBR connections arriving on this port will be subjected to GCRA policing. svcOn: ALL nrtVBR SVCs arriving on this port will be subjected to GCRA policing svcOff: NO nrtVBR SVCs arriving on this port will be subjected to GCRA policing. nrtVBR PVCs will be GCRA policed based on the state of their UPC contract. default: ALL nrtVBR UNI SVCs/SVPs arriving at this port will be subject to GCRA policing and NO nrtVBR NNI SVCs/SVPs arriving at this port will be subject to GCRA policing. nrtVBR PVCs/PVPs arriving at this port will be policed based on the state of their UPC contract.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4), default(5)  

portAAL5PacketDiscardRTVBR 1.3.6.1.4.1.326.2.2.2.1.2.2.1.66
This variable defines the per-port AAL5 packet discard configuration for rtVBR connections. The states mean the following: allOn: All rtVBR AAL5 connections have packet discard performed on them. allOff: AAL5 packet discard is not performed on any rtVBR connections. svcOn: Any rtVBR SVC that 'requests' packet discard will have it performed. For rtVBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection. svcOff: AAL5 packet discard is not performed on any rtVBR SVC's.For rtVBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4)  

portAAL5PacketDiscardNRTVBR 1.3.6.1.4.1.326.2.2.2.1.2.2.1.67
This variable defines the per-port AAL5 packet discard configuration for nrtVBR connections. The states mean the following: allOn: All nrtVBR AAL5 connections have packet discard performed on them. allOff: AAL5 packet discard is not performed on any nrtVBR connections. svcOn: Any nrtVBR SVC that 'requests' packet discard will have it performed. For nrtVBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection. svcOff: AAL5 packet discard is not performed on any nrtVBR SVC's.For nrtVBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4)  

portPPPolicingNRTVBR 1.3.6.1.4.1.326.2.2.2.1.2.2.1.68
This variable defines the per-port AAL5 Partial Packet Policing configuration for nrtVBR connections. The states of this variable mean the following: allOn: All nrtVBR AAL5 connections have partial packet policing performed on them. allOff: AAL5 partial packet policing is not performed on any nrtVBR connections. svcOn: Any nrtVBR SVC that uses AAL5 will have partial packet policing performed on it. For nrtVBR PVC's, partial packet policing will be performed based on the UPC contract of the connection. svcOff: Partial packet policing will not be performed on any nrtVBR SVC's. For nrtVBR PVC's, partial packet policing is enabled based on the UPC contract of the connection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4)  

portPPPolicingRTVBR 1.3.6.1.4.1.326.2.2.2.1.2.2.1.69
This variable defines the per-port AAL5 Partial Packet Policing configuration for rtVBR connections. The states of this variable mean the following: allOn: All rtVBR AAL5 connections have partial packet policing performed on them. allOff: AAL5 partial packet policing is not performed on any rtVBR connections. svcOn: Any rtVBR SVC that uses AAL5 will have partial packet policing performed on it. For rtVBR PVC's, partial packet policing will be performed based on the UPC contract of the connection. svcOff: Partial packet policing will not be performed on any rtVBR SVC's. For rtVBR PVC's, partial packet policing is enabled based on the UPC contract of the connection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allOn(1), allOff(2), svcOn(3), svcOff(4)  

portNrtVbrOverbooking 1.3.6.1.4.1.326.2.2.2.1.2.2.1.70
The percentage of overbooking for nrtVBR connections. The default value is 100 (no overbooking).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..32767  

portNrtVbrBufferOverb 1.3.6.1.4.1.326.2.2.2.1.2.2.1.71
The percentage of buffer overbooking for nrtVBR connections. The default value is 100 (no overbooking).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..32767  

portRtVbrOverbooking 1.3.6.1.4.1.326.2.2.2.1.2.2.1.72
The percentage of overbooking for rtVBR connections. The default value is 100 (no overbooking).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..32767  

portRtVbrBufferOverb 1.3.6.1.4.1.326.2.2.2.1.2.2.1.73
The percentage of buffer overbooking for rtVBR connections. The default value is 100 (no overbooking).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..32767  

portPathOverbooking 1.3.6.1.4.1.326.2.2.2.1.2.2.1.74
The percentage of overbooking for inelastic originating paths. The default value is 100 (no overbooking).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..32767  

atmIfConnSchedTable 1.3.6.1.4.1.326.2.2.2.1.2.3
A table of connection scheduling information on this ATM If.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmIfConnSchedEntry

atmIfConnSchedEntry 1.3.6.1.4.1.326.2.2.2.1.2.3.1
A table of connection scheduling information on this ATM If.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmIfConnSchedEntry  


atmIfConnSchedServCat 1.3.6.1.4.1.326.2.2.2.1.2.3.1.2
Index of this service category within serviceCategoryTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

atmIfConnSchedMode 1.3.6.1.4.1.326.2.2.2.1.2.3.1.3
The scheduling mode used for connections of type atmIfConnSchedServCat on this ATM if. The default choice of AtmConnSchedMode is not allowed at atmIf level.
Status: current Access: read-write
OBJECT-TYPE    
  AtmConnSchedMode  

atmIfConnSchedOverride 1.3.6.1.4.1.326.2.2.2.1.2.3.1.4
The override option used for connections of type atmIfConnSchedServCat on this ATM if.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ifIndexMapTable 1.3.6.1.4.1.326.2.2.2.1.14.1
A table containing information about how physical interfaces ifIndexes relate to the b-n-p triplets. Other ifIndices will not have entries in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IfIndexMapEntry

ifIndexMapEntry 1.3.6.1.4.1.326.2.2.2.1.14.1.1
A table entry containing ifindex/b-n-p information.
Status: current Access: not-accessible
OBJECT-TYPE    
  IfIndexMapEntry  

ifIndexMapIndex 1.3.6.1.4.1.326.2.2.2.1.14.1.1.1
The ifIndex of this entry. The ifindex must be that of a physical interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ifIndexMapBoard 1.3.6.1.4.1.326.2.2.2.1.14.1.1.2
The board number that this ifIndex refers to
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ifIndexMapNetmod 1.3.6.1.4.1.326.2.2.2.1.14.1.1.3
The netmod number that this ifIndex refers to
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ifIndexMapPort 1.3.6.1.4.1.326.2.2.2.1.14.1.1.4
The port number that this ifIndex refers to
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cesExtTable 1.3.6.1.4.1.326.2.2.2.1.16.1
This indicates the value of the next available index to be used for CES creation
Status: current Access: read-only
OBJECT-TYPE    
  TestAndIncr  

cbrctConfTable 1.3.6.1.4.1.326.2.2.2.1.16.2
A table of CBR Cut-through configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CbrctConfEntry

cbrctConfEntry 1.3.6.1.4.1.326.2.2.2.1.16.2.1
A table entry containing CBR Cut-through configuration information for each CES connection.
Status: current Access: not-accessible
OBJECT-TYPE    
  CbrctConfEntry  

cbrctState 1.3.6.1.4.1.326.2.2.2.1.16.2.1.1
This variable indicates whether the CBR Cut-through feature is enabled or disabled on the ingress connection. The values mean: enabled CBR Cut-through enabled disabled CBR Cut-through disabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cbrctIdleDetection 1.3.6.1.4.1.326.2.2.2.1.16.2.1.2
This variable identifies the idle detection mechanism used on this connection. The different values are: idlePattern(1) detection is based on idle pattern detection cas(2) detection is based on CAS signalling
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER idlePattern(1), cas(2)  

cbrctIdleMask 1.3.6.1.4.1.326.2.2.2.1.16.2.1.3
This contains the mask pattern for idle detection.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cbrctNoOfIdlePatterns 1.3.6.1.4.1.326.2.2.2.1.16.2.1.4
This variable contains the number of idle patterns configured for detection.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cbrctIdlePatterns 1.3.6.1.4.1.326.2.2.2.1.16.2.1.5
This contains the patterns for idle detection. For detection based on both idle and mask patterns it contains the idle octet patterns. For detection based on signalling it contains the octet value of AB signalling bits (eg. 00000010 (02H), the bit 0 is B bit and bit 1 is A bit). Maximum of 4 idle patterns are used. The idle patterns get filled from the least significant byte. The cbrctNoOfIdlePatterns gives the number of idle patterns.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cbrctIdleIntPeriod 1.3.6.1.4.1.326.2.2.2.1.16.2.1.6
This contains the integration period for idle detection.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval  

cbrctActiveIntPeriod 1.3.6.1.4.1.326.2.2.2.1.16.2.1.7
This contains the integration period for active detection.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval  

asxAtmIfTable 1.3.6.1.4.1.326.2.2.2.1.20.1
A table of atm interface information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AsxAtmIfEntry

asxAtmIfEntry 1.3.6.1.4.1.326.2.2.2.1.20.1.1
A table entry containing atm interface information.
Status: current Access: not-accessible
OBJECT-TYPE    
  AsxAtmIfEntry  

asxAtmIfName 1.3.6.1.4.1.326.2.2.2.1.20.1.1.1
The persistent name of this atm interface. It is used to index this atm interface. All letters in the asxAtmIfName are always represented in uppercase.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString  

asxAtmIfLinkid 1.3.6.1.4.1.326.2.2.2.1.20.1.1.2
The linkid of this atm interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pathTable 1.3.6.1.4.1.326.2.2.2.1.3.1
A table of information about the virtual paths passing through this ATM switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PathEntry

pathEntry 1.3.6.1.4.1.326.2.2.2.1.3.1.1
A table entry containing path information.
Status: current Access: not-accessible
OBJECT-TYPE    
  PathEntry  

pathPort 1.3.6.1.4.1.326.2.2.2.1.3.1.1.1
The value of this object identifies the input port of this path and is the same as the portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pathVPI 1.3.6.1.4.1.326.2.2.2.1.3.1.1.2
The input VPI (Virtual Path Identifier) of this path.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pathStatus 1.3.6.1.4.1.326.2.2.2.1.3.1.1.3
The status of this path entry.
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

pathNumOutputs 1.3.6.1.4.1.326.2.2.2.1.3.1.1.4
The number of output ports to which this path is routed.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pathMaxChannels 1.3.6.1.4.1.326.2.2.2.1.3.1.1.5
The maximum number of virtual channels that can be allocated on this path.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pathNumChannels 1.3.6.1.4.1.326.2.2.2.1.3.1.1.6
The number of virtual channels currently allocated on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pathMaxBandwidth 1.3.6.1.4.1.326.2.2.2.1.3.1.1.7
The maximum bandwidth of this path, in cells per second.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pathAllocBandwidth 1.3.6.1.4.1.326.2.2.2.1.3.1.1.8
The allocated bandwidth of this path, in cells per second.
Status: current Access: read-create
OBJECT-TYPE    
  Gauge32  

pathUsedBandwidth 1.3.6.1.4.1.326.2.2.2.1.3.1.1.9
The bandwidth being used on this path, in cells per second.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Gauge32  

pathCells 1.3.6.1.4.1.326.2.2.2.1.3.1.1.10
The number of cells transferred over this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pathUptime 1.3.6.1.4.1.326.2.2.2.1.3.1.1.11
The time since this path was created, in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

pathSigProtocol 1.3.6.1.4.1.326.2.2.2.1.3.1.1.12
The signaling protocol that created this path.
Status: current Access: read-only
OBJECT-TYPE    
  AtmSigProtocol  

pathRejectedCells 1.3.6.1.4.1.326.2.2.2.1.3.1.1.13
The number of cells over this path that were rejected (i.e. dropped) by the policer on the switch fabric. This does not include any cells that may have been tagged with CLP=1 by the policer, only cells that were discarded.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pathMinVCI 1.3.6.1.4.1.326.2.2.2.1.3.1.1.14
The minimum VCI that can be allocated on this path.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pathMaxVCI 1.3.6.1.4.1.326.2.2.2.1.3.1.1.15
The maximum VCI that can be allocated on this path.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pathCACErrors 1.3.6.1.4.1.326.2.2.2.1.3.1.1.16
The number of CAC (Call Admission Control) failures on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pathVCIErrors 1.3.6.1.4.1.326.2.2.2.1.3.1.1.17
The number of VCI allocation failures on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pathSetupErrors 1.3.6.1.4.1.326.2.2.2.1.3.1.1.18
The number of connection setup failures on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pathRouteTable 1.3.6.1.4.1.326.2.2.2.1.3.2
A table of information about the routing of paths through this ATM switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PathRouteEntry

pathRouteEntry 1.3.6.1.4.1.326.2.2.2.1.3.2.1
A table entry containing path route information.
Status: current Access: not-accessible
OBJECT-TYPE    
  PathRouteEntry  

pathrInputPort 1.3.6.1.4.1.326.2.2.2.1.3.2.1.1
The value of this object identifies the input port of this path and is the same as the portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pathrInputVPI 1.3.6.1.4.1.326.2.2.2.1.3.2.1.2
The input VPI (Virtual Path Identifier) of this path.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pathrOutputPort 1.3.6.1.4.1.326.2.2.2.1.3.2.1.3
The value of this object identifies the output port of this path and is the same as the portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pathrOutputVPI 1.3.6.1.4.1.326.2.2.2.1.3.2.1.4
The output VPI (Virtual Path Identifier) of this path.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pathrStatus 1.3.6.1.4.1.326.2.2.2.1.3.2.1.5
The status of this path entry.
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

pathrMaxBandwidth 1.3.6.1.4.1.326.2.2.2.1.3.2.1.6
The maximum bandwidth of this path, in cells per second.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pathrAllocBandwidth 1.3.6.1.4.1.326.2.2.2.1.3.2.1.7
The allocated bandwidth of this path, in cells per second.
Status: current Access: read-create
OBJECT-TYPE    
  Gauge32  

pathrCells 1.3.6.1.4.1.326.2.2.2.1.3.2.1.8
The number of cells transferred over this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pathrUptime 1.3.6.1.4.1.326.2.2.2.1.3.2.1.9
The time since this path was created, in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

pathrSigProtocol 1.3.6.1.4.1.326.2.2.2.1.3.2.1.10
The signaling protocol that created this path.
Status: current Access: read-only
OBJECT-TYPE    
  AtmSigProtocol  

pathrRejectedCells 1.3.6.1.4.1.326.2.2.2.1.3.2.1.11
The number of cells over this through path that were rejected (i.e. dropped) by the policer on the switch fabric. This does not include any cells that may have been tagged with CLP=1 by the policer, only cells that were discarded.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pathrLoopVPI 1.3.6.1.4.1.326.2.2.2.1.3.2.1.12
If this value is other than -1, cells destined for pathrOutputPort, pathrOutputVPI will be translated by the netmod to pathrLoopVPI before actually being trasmitted. This was instituted to facilitate single port loopback.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pathrUpcContract 1.3.6.1.4.1.326.2.2.2.1.3.2.1.13
The UPC contract that will be used to police this through path. This is the number of the row in the upcContractTable.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pathrName 1.3.6.1.4.1.326.2.2.2.1.3.2.1.14
The value of this object identifies the name that has been assigned for this path.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

pathrConnectionType 1.3.6.1.4.1.326.2.2.2.1.3.2.1.15
This object identifies the type of the path endpoints with respect to a particular network.
Status: current Access: read-create
OBJECT-TYPE    
  ConnectionType  

pathrServCat 1.3.6.1.4.1.326.2.2.2.1.3.2.1.16
Index of this service category within serviceCategoryTable
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

outputPathTable 1.3.6.1.4.1.326.2.2.2.1.3.3
A table of information about the virtual paths originating at this ATM switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OutputPathEntry

outputPathEntry 1.3.6.1.4.1.326.2.2.2.1.3.3.1
A table entry containing output path information.
Status: current Access: not-accessible
OBJECT-TYPE    
  OutputPathEntry  

opathPort 1.3.6.1.4.1.326.2.2.2.1.3.3.1.1
The value of this object identifies the output port of this path and is the same as the portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

opathVPI 1.3.6.1.4.1.326.2.2.2.1.3.3.1.2
The VPI (Virtual Path Identifier) of this path.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

opathStatus 1.3.6.1.4.1.326.2.2.2.1.3.3.1.3
The status of this path entry.
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

opathMaxChannels 1.3.6.1.4.1.326.2.2.2.1.3.3.1.4
The maximum number of virtual channels that can be allocated on this path.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

opathNumChannels 1.3.6.1.4.1.326.2.2.2.1.3.3.1.5
The number of virtual channels currently allocated on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

opathMaxBandwidth 1.3.6.1.4.1.326.2.2.2.1.3.3.1.6
The maximum bandwidth of this path, in cells per second.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

opathAllocBandwidth 1.3.6.1.4.1.326.2.2.2.1.3.3.1.7
The allocated bandwidth of this path, in cells per second.
Status: current Access: read-create
OBJECT-TYPE    
  Gauge32  

opathUsedBandwidth 1.3.6.1.4.1.326.2.2.2.1.3.3.1.8
The bandwidth used on this path, in cells per second.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Gauge32  

opathCells 1.3.6.1.4.1.326.2.2.2.1.3.3.1.9
The number of cells transmitted on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

opathUptime 1.3.6.1.4.1.326.2.2.2.1.3.3.1.10
The time since this path was created, in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

opathSigProtocol 1.3.6.1.4.1.326.2.2.2.1.3.3.1.11
The signaling protocol that created this path.
Status: current Access: read-only
OBJECT-TYPE    
  AtmSigProtocol  

opathRejectedCells 1.3.6.1.4.1.326.2.2.2.1.3.3.1.12
The number of cells on this output path that were rejected (i.e. dropped) by the policer on the switch fabric. This does not include any cells that may have been tagged with CLP=1 by the policer, only cells that were discarded.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

opathTrafficShapeVPI 1.3.6.1.4.1.326.2.2.2.1.3.3.1.13
The VPI of shaped cells
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

opathVbrOverbooking 1.3.6.1.4.1.326.2.2.2.1.3.3.1.14
The percentage of overbooking for nrtVBR connections. The default value is 100 (no overbooking). A value of -1 indicates that the path is elastic, and therefore the overbooking factors are meaningless.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER -1..32767  

opathVbrBufferOverb 1.3.6.1.4.1.326.2.2.2.1.3.3.1.15
The percentage of buffer overbooking for nrtVBR connections. The default value is 100 (no overbooking). A value of -1 indicates that the path is elastic, and therefore the overbooking factors are meaningless.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER -1..32767  

opathMinVCI 1.3.6.1.4.1.326.2.2.2.1.3.3.1.16
The minimum VCI that can be allocated on this path.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

opathMaxVCI 1.3.6.1.4.1.326.2.2.2.1.3.3.1.17
The maximum VCI that can be allocated on this path.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

opathCACErrors 1.3.6.1.4.1.326.2.2.2.1.3.3.1.18
The number of CAC (Call Admission Control) failures on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

opathVCIErrors 1.3.6.1.4.1.326.2.2.2.1.3.3.1.19
The number of VCI allocation failures on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

opathSetupErrors 1.3.6.1.4.1.326.2.2.2.1.3.3.1.20
The number of connection setup failures on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

opathLoopVPI 1.3.6.1.4.1.326.2.2.2.1.3.3.1.21
If this value is assigned to other than -1, the netmod will modify cell headers received from the fabric that are destined for opathPort, opathVPI to have the vpi value of opathLoopVPI before being transmitted. This extra translation can be used to loop cells back onto the fabric using a single port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

opathSchedMode 1.3.6.1.4.1.326.2.2.2.1.3.3.1.22
The value of this object identifies the scheduling mode for this originating path.
Status: current Access: read-create
OBJECT-TYPE    
  AtmOrigPathSchedMode  

opathNrtVbrOverbooking 1.3.6.1.4.1.326.2.2.2.1.3.3.1.23
The percentage of overbooking for nrtVBR connections. The default value is 100 (no overbooking). A value of -1 indicates that the path is elastic, and therefore the overbooking factors are meaningless.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..32767  

opathNrtVbrBufferOverb 1.3.6.1.4.1.326.2.2.2.1.3.3.1.24
The percentage of buffer overbooking for nrtVBR connections. The default value is 100 (no overbooking). A value of -1 indicates that the path is elastic, and therefore the overbooking factors are meaningless.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..32767  

opathRtVbrOverbooking 1.3.6.1.4.1.326.2.2.2.1.3.3.1.25
The percentage of overbooking for rtVBR connections. The default value is 100 (no overbooking). A value of -1 indicates that the path is elastic, and therefore the overbooking factors are meaningless.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..32767  

opathRtVbrBufferOverb 1.3.6.1.4.1.326.2.2.2.1.3.3.1.26
The percentage of buffer overbooking for rtVBR connections. The default value is 100 (no overbooking). A value of -1 indicates that the path is elastic, and therefore the overbooking factors are meaningless.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..32767  

outputPathStatsTable 1.3.6.1.4.1.326.2.2.2.1.3.4
A table of statistics information about the virtual paths originating at this ATM switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OutputPathStatsEntry

outputPathStatsEntry 1.3.6.1.4.1.326.2.2.2.1.3.4.1
A table entry containing originating channel statistics information.
Status: current Access: not-accessible
OBJECT-TYPE    
  OutputPathStatsEntry  

opathStatsPort 1.3.6.1.4.1.326.2.2.2.1.3.4.1.1
The value of this object identifies the output port of this channel and is the same as the opathPort, and portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

opathStatsVPI 1.3.6.1.4.1.326.2.2.2.1.3.4.1.2
The value of this object identifies the output VPI (Virtual Path Identifier) of this channel and is the same as the opathVPI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

opathStatsLostCells 1.3.6.1.4.1.326.2.2.2.1.3.4.1.3
The number of cells on this output path that were dropped at the output netmod.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

opathStatsTransmittedCells 1.3.6.1.4.1.326.2.2.2.1.3.4.1.4
The number of cells on this output path that were transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

opathStatsIntentionalLostCells 1.3.6.1.4.1.326.2.2.2.1.3.4.1.5
The number of cells on this output path that were dropped intentionally at the output netmod.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

opathStatsCLP0Cells 1.3.6.1.4.1.326.2.2.2.1.3.4.1.6
The number of CLP = 0 cells transmitted on this output path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

opathStatsLostPackets 1.3.6.1.4.1.326.2.2.2.1.3.4.1.7
The number of packets on this output path that were dropped at the output netmod.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

opathStatsTransmittedPackets 1.3.6.1.4.1.326.2.2.2.1.3.4.1.8
The number of Packets on this output path that were transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

outputPathChannelSchedTable 1.3.6.1.4.1.326.2.2.2.1.3.5
A table of connection scheduling information on this output path.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OutputPathChannelSchedEntry

outputPathChannelSchedEntry 1.3.6.1.4.1.326.2.2.2.1.3.5.1
A table of connection scheduling information on this output path.
Status: current Access: not-accessible
OBJECT-TYPE    
  OutputPathChannelSchedEntry  

opathChannelSchedPort 1.3.6.1.4.1.326.2.2.2.1.3.5.1.1
Index of this port
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

opathChannelSchedVPI 1.3.6.1.4.1.326.2.2.2.1.3.5.1.2
The value of this object identifies the output VPI (Virtual Path Identifier) of this path.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

opathChannelSchedServCat 1.3.6.1.4.1.326.2.2.2.1.3.5.1.3
Index of this service category within serviceCategoryTable
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

opathChannelSchedSchedMode 1.3.6.1.4.1.326.2.2.2.1.3.5.1.4
The scheduling mode used for channels of type opathChannelSchedServCat within this path. The default choice of AtmConnSchedMode is not allowed at path level.
Status: current Access: read-write
OBJECT-TYPE    
  AtmConnSchedMode  

opathChannelSchedSchedOverride 1.3.6.1.4.1.326.2.2.2.1.3.5.1.5
The override option used for channels of type opathChannelSchedServCat within this path
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

channelTable 1.3.6.1.4.1.326.2.2.2.1.4.1
A table of information about the virtual channels passing through this ATM switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ChannelEntry

channelEntry 1.3.6.1.4.1.326.2.2.2.1.4.1.1
A table entry containing channel information.
Status: current Access: not-accessible
OBJECT-TYPE    
  ChannelEntry  

chanPort 1.3.6.1.4.1.326.2.2.2.1.4.1.1.1
The value of this object identifies the input port of this channel and is the same as the pathPort and portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

chanVPI 1.3.6.1.4.1.326.2.2.2.1.4.1.1.2
The value of this object identifies the input VPI (Virtual Path Identifier) of this channel, and is the same as the pathVPI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

chanVCI 1.3.6.1.4.1.326.2.2.2.1.4.1.1.3
The input VCI (Virtual Channel Identifier) of this channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

chanStatus 1.3.6.1.4.1.326.2.2.2.1.4.1.1.4
The status of this channel entry.
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

chanNumOutputs 1.3.6.1.4.1.326.2.2.2.1.4.1.1.5
The number of output ports to which this channel is routed.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

chanAllocBandwidth 1.3.6.1.4.1.326.2.2.2.1.4.1.1.6
The allocated bandwidth of this channel, in cells per second.
Status: current Access: read-create
OBJECT-TYPE    
  Gauge32  

chanUsedBandwidth 1.3.6.1.4.1.326.2.2.2.1.4.1.1.7
The bandwidth used on this channel, in cells per second.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Gauge32  

chanCells 1.3.6.1.4.1.326.2.2.2.1.4.1.1.8
The number of cells transferred on this channel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

chanUptime 1.3.6.1.4.1.326.2.2.2.1.4.1.1.9
The time since this channel was created, in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

chanSigProtocol 1.3.6.1.4.1.326.2.2.2.1.4.1.1.10
The signaling protocol that created this channel.
Status: current Access: read-only
OBJECT-TYPE    
  AtmSigProtocol  

chanRejectedCells 1.3.6.1.4.1.326.2.2.2.1.4.1.1.11
The number of cells on this channel that were rejected (dropped) by the policer on the switch fabric. This does not include any cells that may have been tagged with CLP=1 by the policer, only cells that were discarded.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

chanCDV 1.3.6.1.4.1.326.2.2.2.1.4.1.1.12
The channel Cell Delay Variation Tolerance (CDV), specified in microseconds, indicates the time window in which a cell may be received on a channel and be accepted. A cell that is received on a channel outside the CDV window will be dropped or tagged, based on the value of chanPolicingAction. The chanCDV value overrides the default value inherited from the link.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

chanPolicingAction 1.3.6.1.4.1.326.2.2.2.1.4.1.1.13
This object indicates the action the switch will take in case of bandwidth violation on this channel.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tag(1), drop(2)  

chanUpcContract 1.3.6.1.4.1.326.2.2.2.1.4.1.1.14
The UPC contract that will be used to police this channel. This is the number of the row in the upcContractTable.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

chanServCat 1.3.6.1.4.1.326.2.2.2.1.4.1.1.15
Index of this service category within serviceCategoryTable
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

chanQosPoliceScheme 1.3.6.1.4.1.326.2.2.2.1.4.1.1.16
It identifies the policing associated with the UPC contract as defined in the ATM Forum TM 4.0 specifications. However, the policing schemes cbr0 and cbr0tag are specific to FORE switches
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER cbr1(1), cbr0(2), cbr0tag(3), vbr1(4), vbr2(5), vbr3(6), abr1(7), ubr1(8), ubr2(9)  

chanQosPCR 1.3.6.1.4.1.326.2.2.2.1.4.1.1.17
The peak cell rate (cells/sec)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

chanQosSCR 1.3.6.1.4.1.326.2.2.2.1.4.1.1.18
The sustained cell rate (cells/sec). It also holds the PCR0 value for cbr0 & cbr0tag contracts
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

chanQosMBS 1.3.6.1.4.1.326.2.2.2.1.4.1.1.19
The maximum burst size (cells)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

chanQosCDVT 1.3.6.1.4.1.326.2.2.2.1.4.1.1.20
The channel Cell Delay Variation Tolerance (CDVT), specified in microseconds, indicates the time window in which a cell may be received on a channel and be accepted. A cell that is received on a channel outside the CDV window will be dropped or tagged, based on the value of chanPolicingAction. The chanCDV value overrides the default value inherited from the link.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

chanQosPoliceState 1.3.6.1.4.1.326.2.2.2.1.4.1.1.21
Indicates if this connection is policed for traffic violations. When set to 'on' it overrides the policing status of the atm interface on which this connection is established.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

chanQosIsAAL5 1.3.6.1.4.1.326.2.2.2.1.4.1.1.22
Indicates if this connection is AAL 5
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

chanQosPerPacketPolicing 1.3.6.1.4.1.326.2.2.2.1.4.1.1.23
Should we perform AAL5 Partial Packet Policing on this UPC contract. This variable only has meaning if the connections is also AAL5.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

channelRouteTable 1.3.6.1.4.1.326.2.2.2.1.4.2
A table of information about the routing of channels through this ATM switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ChannelRouteEntry

channelRouteEntry 1.3.6.1.4.1.326.2.2.2.1.4.2.1
A table entry containing channel route information.
Status: current Access: not-accessible
OBJECT-TYPE    
  ChannelRouteEntry  

chanrInputPort 1.3.6.1.4.1.326.2.2.2.1.4.2.1.1
The value of this object identifies the input port of this channel and is the same as the chanPort, pathPort, and portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

chanrInputVPI 1.3.6.1.4.1.326.2.2.2.1.4.2.1.2
The value of this object identifies the input VPI (Virtual Path Identifier) of this channel, and is the same as the chanVPI, and pathVPI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

chanrInputVCI 1.3.6.1.4.1.326.2.2.2.1.4.2.1.3
The value of this object identifies the input VCI (Virtual Channel Identifier) of this channel, and is the same as chanVCI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

chanrOutputPort 1.3.6.1.4.1.326.2.2.2.1.4.2.1.4
The value of this object identifies the output port of this channel and is the same as the opathPort, and portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

chanrOutputVPI 1.3.6.1.4.1.326.2.2.2.1.4.2.1.5
The value of this object identifies the output VPI (Virtual Path Identifier) of this channel and is the same as the opathVPI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

chanrOutputVCI 1.3.6.1.4.1.326.2.2.2.1.4.2.1.6
The output VCI (Virtual Channel Identifier) of this channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

chanrStatus 1.3.6.1.4.1.326.2.2.2.1.4.2.1.7
The status of this channel entry.
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

chanrSigProtocol 1.3.6.1.4.1.326.2.2.2.1.4.2.1.8
The signaling protocol that created this channel.
Status: current Access: read-only
OBJECT-TYPE    
  AtmSigProtocol  

chanrName 1.3.6.1.4.1.326.2.2.2.1.4.2.1.9
The value of this object identifies the name that has been assigned for this channel.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

chanrConnectionType 1.3.6.1.4.1.326.2.2.2.1.4.2.1.10
This object identifies the type of the channel endpoints with respect to a particular network.
Status: current Access: read-create
OBJECT-TYPE    
  ConnectionType  

reverseChannelRouteTable 1.3.6.1.4.1.326.2.2.2.1.4.3
A table of information about reverse channel routes through this ATM switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ReverseChannelRouteEntry

reverseChannelRouteEntry 1.3.6.1.4.1.326.2.2.2.1.4.3.1
A table entry containing reverse channel route information.
Status: current Access: not-accessible
OBJECT-TYPE    
  ReverseChannelRouteEntry  

revChanrOutputPort 1.3.6.1.4.1.326.2.2.2.1.4.3.1.1
The value of this object identifies the output port of this channel and is the same as the chanrOutputPort, opathPort and portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

revChanrOutputVPI 1.3.6.1.4.1.326.2.2.2.1.4.3.1.2
The value of this object identifies the output VPI (Virtual Path Identifier) of this channel and is the same as the chanrOutputVPI and opathVPI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

revChanrOutputVCI 1.3.6.1.4.1.326.2.2.2.1.4.3.1.3
The output VCI (Virtual Channel Identifier) of this channel and is the same as chanrOutputVCI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

revChanrInputPort 1.3.6.1.4.1.326.2.2.2.1.4.3.1.4
The value of this object identifies the input port of this channel and is the same as the chanPort, chanrInputPort, pathPort, and portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

revChanrInputVPI 1.3.6.1.4.1.326.2.2.2.1.4.3.1.5
The value of this object identifies the input VPI (Virtual Path Identifier) of this channel, and is the same as the chanVPI, chanrInputVPI and pathVPI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

revChanrInputVCI 1.3.6.1.4.1.326.2.2.2.1.4.3.1.6
The value of this object identifies the input VCI (Virtual Channel Identifier) of this channel, and is the same as chanVCI and chanrInputVCI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

revChanrSigProtocol 1.3.6.1.4.1.326.2.2.2.1.4.3.1.7
The signaling protocol that created this channel and is the same as chanrSigProtocol.
Status: current Access: read-only
OBJECT-TYPE    
  AtmSigProtocol  

outputChannelStatsTable 1.3.6.1.4.1.326.2.2.2.1.4.4
A table of statistics information about the virtual channels originating at this ATM switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OutputChannelStatsEntry

outputChannelStatsEntry 1.3.6.1.4.1.326.2.2.2.1.4.4.1
A table entry containing originating channel statistics information.
Status: current Access: not-accessible
OBJECT-TYPE    
  OutputChannelStatsEntry  

ochanStatsPort 1.3.6.1.4.1.326.2.2.2.1.4.4.1.1
The value of this object identifies the output port of this channel and is the same as the opathPort, and portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ochanStatsVPI 1.3.6.1.4.1.326.2.2.2.1.4.4.1.2
The value of this object identifies the output VPI (Virtual Path Identifier) of this channel and is the same as the opathVPI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ochanStatsVCI 1.3.6.1.4.1.326.2.2.2.1.4.4.1.3
The output VCI (Virtual Channel Identifier) of this channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ochanStatsLostCells 1.3.6.1.4.1.326.2.2.2.1.4.4.1.4
The number of cells on this output channel that were dropped at the output netmod.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ochanStatsTransmittedCells 1.3.6.1.4.1.326.2.2.2.1.4.4.1.5
The number of cells on this output channel that were transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ochanStatsIntentionalLostCells 1.3.6.1.4.1.326.2.2.2.1.4.4.1.6
The number of cells on this output channel that were dropped intentionally.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ochanStatsCLP0Cells 1.3.6.1.4.1.326.2.2.2.1.4.4.1.7
The number of CLP = 0 cells transmitted on this output path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ochanStatsLostPackets 1.3.6.1.4.1.326.2.2.2.1.4.4.1.8
The number of packets on this output path that were dropped at the output netmod.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ochanStatsTransmittedPackets 1.3.6.1.4.1.326.2.2.2.1.4.4.1.9
The number of Packets on this output path that were transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  


linkTable 1.3.6.1.4.1.326.2.2.2.1.5.2
A table of links describing this switch's view of the ATM network topology.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkEntry

linkEntry 1.3.6.1.4.1.326.2.2.2.1.5.2.1
A table entry containing link information.
Status: current Access: not-accessible
OBJECT-TYPE    
  LinkEntry  

linkSrc 1.3.6.1.4.1.326.2.2.2.1.5.2.1.1
The ATM address of the source switch of this link.
Status: current Access: read-only
OBJECT-TYPE    
  SpansAddress  

linkDest 1.3.6.1.4.1.326.2.2.2.1.5.2.1.2
The ATM address of the destination switch of this link.
Status: current Access: read-only
OBJECT-TYPE    
  SpansAddress  

linkCapacity 1.3.6.1.4.1.326.2.2.2.1.5.2.1.3
The free capacity of this link in kilobits per second.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkAge 1.3.6.1.4.1.326.2.2.2.1.5.2.1.4
The freshness of this link information. The actual value has no units associated with it. It should be used for comparison.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sigPathTable 1.3.6.1.4.1.326.2.2.2.1.6.1.1
A table of general information about the signaling path.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SigPathEntry

sigPathEntry 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1
A table entry containing signaling path information, indexed by port and path.
Status: current Access: not-accessible
OBJECT-TYPE    
  SigPathEntry  

sigPathPort 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.1
The value of this object identifies the port of this signalling path, and is the same as the portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sigPathVPI 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.2
The VPI (Virtual Path Identifier) of this signaling path.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sigPathVCI 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.3
The VCI (Virtual Channel Identifier) of the signaling channel within the signaling path.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

sigPathClsVCI 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.4
The VCI (Virtual Channel Identifier) of the connectionless channel within the signaling path.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

sigPathAdminStatus 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.5
The desired state of this signaling channel. The up(1) state dictates that SPANS (Simple Protocol for ATM Network Siganlling) messages are used for signalling. The down(2) state dictates the SPANS protocol is not used for signalling.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

sigPathOperStatus 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.6
The current operational state of this signaling channel, as determined either by administrative action, when the value of sigPathAdminStatus is down(2), or by a link monitoring protocol, when the value of sigPathAdminStatus is up(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

sigPathEntryStatus 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.7
The status of this signaling path entry.
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

sigPathAALType 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.8
The AAL (ATM Adaptation LAyer) type that is used by this signaling path.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER type34(1), type5(2), auto(3)  

sigPathCDV 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.9
The signalling path Cell Delay Variation (CDV) specified in microseconds, indicates the time window in which a cell may be received on a signalling channel and be accepted. A cell that is received on a channel outside the CDV window will be dropped. The sigPathCDV value overrides the default value of switchCDV.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

sigPathPolicingAction 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.10
This object indicates the action the switch will take in case of bandwidth violation on a signalling channel. The value set here overrides the default value of switchPolicingAction.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tag(1), drop(2)  

sigPathRemoteAtmAddress 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.11
The ATM address of the entity connected to this signalling path.
Status: current Access: read-only
OBJECT-TYPE    
  SpansAddress  

sigPathRemoteIpAddress 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.12
The IP address of the entity connected to this signalling path.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

sigPathType 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.13
The type of the signalling path connection. uni(1) (User Network Interface) means that there is a host on remote side, while nni(2) (Network Network Interface) means there is another switch, that speaks SPANS, on the remote side.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER uni(1), nni(2)  

sigPathClsUpcContract 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.14
The UPC contract that will be used to police the connectionless VC. This is the number of a row in the upcContractTable
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

sigPathSigReservedBW 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.15
Bandwidth reserved for the SPANS Signaling VC, in cells/sec.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

sigPathMinVCI 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.16
The minimum configured VCI (Virtual Channel Identifier) that can be used for SVCs (Signalled Virtual Circuits).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

sigPathMaxVCI 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.17
The maximum configured VCI (Virtual Channel Identifier) that can be used for SVCs (Signalled Virtual Circuits).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

sigPathOpenTimeout 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.18
The timeout in msec for SPANS open requests.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

sigPathCloseTimeout 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.19
The timeout in msec for SPANS close requests.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

sigPathOutputSigService 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.20
Service Queue where the output signalling vc should be inserted into.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER vbr(1), ubr(2), oam(3), default(4)  

sigPathAALOperType 1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.21
The AAL (ATM Adaptation LAyer) type that is currently being used by this signaling path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER type34(1), type5(2)  

sigPathStatsTable 1.3.6.1.4.1.326.2.2.2.1.6.1.2
A table of statistics about the signaling path.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SigPathStatsEntry

sigPathStatsEntry 1.3.6.1.4.1.326.2.2.2.1.6.1.2.1
A table entry containing signaling path statistics, indexed by port and path.
Status: current Access: not-accessible
OBJECT-TYPE    
  SigPathStatsEntry  

sigPathStatsPort 1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.1
The value of this object identifies the port of this signalling path, and is the same as sigPathPort.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sigPathStatsVPI 1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.2
The value of this object identifies the VPI (Virtual Path Identifier) of this signaling path statistics entry, and is the same as sigPathVPI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sigPathVCCs 1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.3
The number of Virtual Channel Connections (VCCs) on this signaling path.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

sigPathRestarts 1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.4
The number of times the switch has lost and regained contact with the remote signaling entity on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sigPathCallsCompletions 1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.5
The number of successfully completed calls on this signaling path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sigPathCallsFailures 1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.6
The number of call failures on this signaling path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sigPathCallsRejections 1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.7
The number of connections on this signaling path that were rejected by the far end.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sigPathSpansTransmittedMessages 1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.8
The total number of SPANS messages that have been transmitted over this signalling path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sigPathSpansReceivedMessages 1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.9
The total number of SPANS messages that have been received on this signalling path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sigPathClsTransmittedMessages 1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.10
The total number of connectionless messages that have been transmitted over this signalling path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sigPathClsReceivedMessages 1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.11
The total number of connectionless messages that have been received on this signalling path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

spvcSrcNumberOfSPVCs 1.3.6.1.4.1.326.2.2.2.1.6.1.3
The number of SPVCs (Smart Permanent Virtual Circuits) that are going out of this switch (i.e. this switch is their source).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

spvcSrcTable 1.3.6.1.4.1.326.2.2.2.1.6.1.4
This table contains information about SPVCs (Smart Permanent Virtual Circuits) that their source is this switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SpvcSrcEntry

spvcSrcEntry 1.3.6.1.4.1.326.2.2.2.1.6.1.4.1
A table entry containing source SPVC (Smart Permanent Virtual Circuits) information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SpvcSrcEntry  

spvcSrcSpvcId 1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.1
The value of this object uniquely identify the SPVC (Smart Permanent Virtual Circuits) that this switch is its source.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

spvcSrcSwitchAddr 1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.2
The ATM address of the source switch.
Status: current Access: read-only
OBJECT-TYPE    
  SpansAddress  

spvcSrcDestSpvcId 1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.3
The SPVC (Smart Permanent Virtual Circuits) identifier at the destination switch. This object should match the spvcDestSpvcId at the destination switch.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

spvcSrcDestSwitchAddr 1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.4
The ATM address of the destination switch.
Status: current Access: read-create
OBJECT-TYPE    
  SpansAddress  

spvcSrcInPort 1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.5
The value of this object identifies the input port of this SPVC (Smart Permanent Virtual Circuits), and is the same as the chanrInputPort, chanPort, pathPort, and portNumber.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

spvcSrcInVPI 1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.6
The value of this object identifies the input VPI (Virtual Path Identifier) of this SPVC (Smart Permanent Virtual Circuits), and is the same as the chanrInputVPI, chanVPI, pathVPI.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

spvcSrcInVCI 1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.7
The value of this object identifies the input VCI (Virtual Channel Identifier) of this SPVC (Smart Permanent Virtual Circuits), and is the same as the chanrInputVCI.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

spvcSrcAllocBandwidth 1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.8
The allocated bandwidth of this SPVC (Smart Permanent Virtual Circuits).
Status: current Access: read-create
OBJECT-TYPE    
  Gauge32  

spvcSrcUpTime 1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.9
The time since this SPVC (Smart Permanent Virtual Circuits) was created in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

spvcSrcStatus 1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.10
The status of this SPVC (Smart Permanent Virtual Circuits).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

spvcSrcEntryStatus 1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.11
The status of this SPVC (Smart Permanent Virtual Circuits) entry.
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

spvcDestNumberOfSPVCs 1.3.6.1.4.1.326.2.2.2.1.6.1.5
The number of SPVCs (Smart Permanent Virtual Circuits) that are coming into this switch (i.e. this switch is their destination).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

spvcDestTable 1.3.6.1.4.1.326.2.2.2.1.6.1.6
This table contains information about SPVCs (Smart Permanent Virtual Circuits) that their destination is this switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SpvcDestEntry

spvcDestEntry 1.3.6.1.4.1.326.2.2.2.1.6.1.6.1
A table entry containing destination SPVC (Smart Permanent Virtual Circuits) information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SpvcDestEntry  

spvcDestSpvcId 1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.1
The value of this object uniquely identify the SPVC (Smart Permanent Virtual Circuits) that this switch is its destination. The range of this object is [1..spvcDestNumberOfSPVCs].
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

spvcDestSwitchAddr 1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.2
The ATM address of this (the destination) switch.
Status: current Access: read-only
OBJECT-TYPE    
  SpansAddress  

spvcDestSrcSpvcId 1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.3
The SPVC (Smart Permanent Virtual Circuits) identifier at the source switch. This object should match the spvcSrcSpvcId at the source switch.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

spvcDestSrcSwitchAddr 1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.4
The ATM address of the source switch.
Status: current Access: read-create
OBJECT-TYPE    
  SpansAddress  

spvcDestOutPort 1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.5
The value of this object identifies the output port of this SPVC (Smart Permanent Virtual Circuits) and is the same as the chanrOutputPort, opathPort, and portNumber.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

spvcDestOutVPI 1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.6
The value of this object identifies the output VPI (Virtual Path Identifier) of this SPVC (Smart Permanent Virtual Circuits), and is the same as the chanrOutputVPI, and opathVPI.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

spvcDestOutVCI 1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.7
The value of this object identifies the output VCI (Virtual Channel Identifier) of this SPVC (Smart Permanent Virtual Circuits), and is the same as the chanrOutputVCI.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

spvcDestAllocBandwidth 1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.8
The allocated bandwidth of this SPVC (Smart Permanent Virtual Circuits).
Status: current Access: read-create
OBJECT-TYPE    
  Gauge32  

spvcDestUpTime 1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.9
The time since this SPVC (Smart Permanent Virtual Circuits) was created in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

spvcDestStatus 1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.10
The status of this SPVC (Smart Permanent Virtual Circuits).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

spvcDestEntryStatus 1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.11
The status of this SPVC (Smart Permanent Virtual Circuits) entry.
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

pnniSpvcSrcNumberOfSPVCs 1.3.6.1.4.1.326.2.2.2.1.6.2.2
The number of SPVCs (Smart Permanent Virtual Circuits) that have their source at this switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcTable 1.3.6.1.4.1.326.2.2.2.1.6.2.3
This table contains information about SPVCs (Smart Permanent Virtual Circuits) that have their source at this switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PnniSpvcSrcEntry

pnniSpvcSrcEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1
A table entry containing source SPVC (Smart Permanent Virtual Circuits) information.
Status: current Access: not-accessible
OBJECT-TYPE    
  PnniSpvcSrcEntry  

pnniSpvcSrcIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.1
The value of this object uniquely identify the SPVCs (Smart Permanent Virtual Circuits) that have this switch as their source.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcCallingPort 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.2
The value of this object identifies the input port of this SPVC (Smart Permanent Virtual Circuits), and is the same as the chanrInputPort, chanPort, pathPort, and portNumber.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcCallingVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.3
The VPI to be used at the Calling NI for this SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcCallingVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.4
The VCI to be used at the Calling NI SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcCalledAtmAddr 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.5
The ATM address of the distant end NI (remote switch) for this SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  NsapAddr  

pnniSpvcSrcCalledPort 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.6
The value of this object identifies the port of this SPVC (Smart Permanent Virtual Circuits) at the destination end. It has a value of -1 if the port at the destination switch cannot be determined.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcCalledVPVCSel 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.7
The Called VPI/VCI value selection qualifier.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER noPref(1), require(2)  

pnniSpvcSrcCalledVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.8
The VPI to be used at the Called NI for this SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcCalledVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.9
The VCI to be used at the Called NI for this SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcCalledAssignedVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.10
The VPI assigned at the Called NI for this SPVC. This value is only meaningful if the SPVC status is up.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcCalledAssignedVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.11
The VCI assigned at the Called NI for this SPVC. This value is only meaningful if the SPVC status is up.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcFwdUpcKey 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.12
The forward UPC traffic contract key for this SPVC. This key must be defined in the upcContractTable.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcBckUpcKey 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.13
The forward UPC traffic contract key for this SPVC. This key must be defined in the upcContractTable.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcBearerClass 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.14
The requested broadband bearer class for this SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER classA(1), classC(2), classX(3)  

pnniSpvcSrcTrafficType 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.15
The requested broadband bearer traffic type for this SPVC.
Status: obsolete Access: read-create
OBJECT-TYPE    
  INTEGER noIndication(1), cbr(2), vbr(3)  

pnniSpvcSrcTimingReq 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.16
The requested broadband bearer timing requirements for this SPVC.
Status: obsolete Access: read-create
OBJECT-TYPE    
  INTEGER noIndication(1), end2endRequired(2), end2endNotReqd(3)  

pnniSpvcSrcSusceptClip 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.17
The requested broadband bearer susceptability to for this SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

pnniSpvcSrcFwdQoSClass 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.18
The requested quality of service for this SPVC in the forward (calling to called) direction.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER class0(1), class1(2), class2(3), class3(4), class4(5)  

pnniSpvcSrcBckQoSClass 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.19
The requested quality of service for this SPVC in the backward (called to calling) direction.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER class0(1), class1(2), class2(3), class3(4), class4(5)  

pnniSpvcSrcTransitNetSel 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.20
The optional transit network selection for this SPVC.
Status: current Access: read-only
OBJECT-TYPE    
  TransitNetwork  

pnniSpvcSrcLastFailCause 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.21
The last call setup failure cause code for this SPVC.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pnniSpvcSrcRetryCount 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.22
The number of times the call setup has been attempted since the SPVC creation or the last successful call setup.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcLastChangeTime 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.23
The time since this SPVC (Smart Permanent Virtual Circuits) has been up/down in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

pnniSpvcSrcStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.24
The operational status of this SPVC (Smart Permanent Virtual Circuit).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), failed(3)  

pnniSpvcSrcName 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.25
The value of this object identifies the name that has been assigned for this SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

pnniSpvcSrcEntryStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.26
The status of this SPVC (Smart Permanent Virtual Circuits) entry.
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

pnniSpvcSrcRouteCost 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.27
The cumulative route cost for the current route of this SPVC (Smart Permanent Virtual Circuits).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcDtlIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.28
The Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). This variable has been deprecated. Any writes to this variable will be treated as writes to pnniSpvcSrcDtlIndex1. This value must be defined in the ftPnniDTLTable. The DTL specifies a preferred call routing for the SVC portion of the SPVC.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcActiveDtlIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.29
The Active Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). This value along with pnniSpvcSrcActiveDtlNodeIndex uniquely identifies the DTL that is currently used by the SVC portion of the SPVC.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcRerouteStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.30
The status of the reroute function for this SPVC (Smart Permanent Virtual Circuit). If set to disabled(2), no rerouting will be attempted for this SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

pnniSpvcSrcCallingDomain 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.31
The Domain ID to be used at the Calling NI SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcQosIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.32
The index for the QOS Class Expansion Table to be used for this spvc.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcDtlIndex1 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.33
The first Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). This value must be defined in the ftPnniDTLTable. The DTL specifies a preferred call routing for the SVC portion of the SPVC.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcDtlIndex2 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.34
The second Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). This value must be defined in the ftPnniDTLTable. The DTL specifies a preferred call routing for the SVC portion of the SPVC.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcDtlIndex3 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.35
The third Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). This value must be defined in the ftPnniDTLTable. The DTL specifies a preferred call routing for the SVC portion of the SPVC.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcDtlIndex4 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.36
The fourth Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). This value must be defined in the ftPnniDTLTable. The DTL specifies a preferred call routing for the SVC portion of the SPVC.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcDtlWeight1 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.37
The weight of the first Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). The weight specifies the priority of this DTL index among the four DTL indices that can be specified for a particular SPVC.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcDtlWeight2 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.38
The weight of the second Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). The weight specifies the priority of this DTL index among the four DTL indices that can be specified for a particular SPVC.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcDtlWeight3 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.39
The weight of the third Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). The weight specifies the priority of this DTL index among the four DTL indices that can be specified for a particular SPVC.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcDtlWeight4 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.40
The weight of the fourth Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). The weight specifies the priority of this DTL index among the four DTL indices that can be specified for a particular SPVC.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcBackoffStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.41
The status of the backoff function for this SPVC (Smart Permanent Virtual Circuit). If set to disabled(2), directed dtls configured for this SPVC will be continually retried on failure.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

pnniSpvcSrcPriority 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.42
Priority of this SPVCC for connection
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcLastLocation 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.43
The last call setup failure location code for this SPVC. This indicates the switch that initiated the clearing for the call. This is formatted as a text string with the fields: FMT: Indicates diagnostic format RMT: Indicates whether a remote switch is the source of the failure or this switch inserted the location diag LINK:Link id that clear pertains to VPI: VPI that clear pertains to The remaining fields are format specific
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pnniSpvcSrcOldRouteCost 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.44
This OID is specified only to be included the the pnniSpvcUp trap. It specifies the path cost of the call the previous time this call was up. If the call has not been up, this will report a value of -1.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcDownReason 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.45
This OID is specified only to be included the the pnniSpvccDown and pnniSpvccFail traps. This specifies whether the SPVC call was cleared due to a better route being found, a network failure, or SPVC deletion.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER reroute(1), failure(2), deletion(3)  

pnniSpvcSrcActiveDtlNodeIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.46
The Node index of the Active Designated Transit List for this SPVC (Smart Permanent Virtual Circuit). The active DTL indexed by the node index and DTL index identifies the DTL that is currently used by the SVC portion of the SPVC. The value of this object is 65535 for FTPNNI nodes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcDtlTag 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.47
This value specifies an index into a table of DTLs, the DTL entries in this table will be used to setup the SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcAutoDtlStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.48
The status of the dynamic path selection function for this SPVC (Smart Permanent Virtual Circuit). If set to disabled(2), auto path selection will not be used.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

pnniSpvcSrcRGroupIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.49
This specifies the entry in the Spvxc Redundancy Group table for information regarding the secondary port to be used as the redundant port
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..65535  

pnniSpvcSrcSecondaryVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.50
The Secondary VPI to be used at the originating switch for the redundant permanent portion of this SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcSrcSecondaryVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.51
The Secondary VCI to be used at the originating switch for the redundant permanent portion of this SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvcDestNumberOfSPVCs 1.3.6.1.4.1.326.2.2.2.1.6.2.4
The number of connected SPVCs (Smart Permanent Virtual Circuits) that have their destination at this switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcDestTable 1.3.6.1.4.1.326.2.2.2.1.6.2.5
This table contains information about SPVCs (Smart Permanent Virtual Circuits) that have their destination at this switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PnniSpvcDestEntry

pnniSpvcDestEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1
A table entry containing destination SPVC (Smart Permanent Virtual Circuits) information.
Status: current Access: not-accessible
OBJECT-TYPE    
  PnniSpvcDestEntry  

pnniSpvcDestIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.1
The value of this object uniquely identify the SPVCs (Smart Permanent Virtual Circuits) that have this switch as their source.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcDestCallingAtmAddr 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.2
The ATM address of the local end NI (on this switch) for this SPVC.
Status: current Access: read-only
OBJECT-TYPE    
  NsapAddr  

pnniSpvcDestCallingPort 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.3
The value of this object identifies the port of this terminating SPVC (Smart Permanent Virtual Circuits) at the source end. It has a value of -1 if the port at the destination switch cannot be determined.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcDestCallingVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.4
The VPI to be used at the Calling NI for this SPVC.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcDestCallingVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.5
The VCI to be used at the Calling NI for this SPVC.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcDestCalledAtmAddr 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.6
The ATM address of the distant end NI (remote switch) for this SPVC.
Status: current Access: read-only
OBJECT-TYPE    
  NsapAddr  

pnniSpvcDestCalledPort 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.7
The value of this object identifies the port of this terminating SPVC (Smart Permanent Virtual Circuits) at the destination end. It has a value os -1 if the port at the destination switch cannot be determined.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcDestAssignedVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.8
The VPI assigned at the Called NI for this SPVC. This value is only meaningful if the SPVC status is up.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcDestAssignedVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.9
The VCI assigned at the Called NI for this SPVC. This value is only meaningful if the SPVC status is up.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvcDestBearerClass 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.10
The broadband bearer class for this SPVC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER classA(1), classC(2), classX(3)  

pnniSpvcDestTrafficType 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.11
The broadband bearer traffic type for this SPVC.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER noIndication(1), cbr(2), vbr(3)  

pnniSpvcDestTimingReq 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.12
The broadband bearer timing requirements for this SPVC.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER noIndication(1), end2endRequired(2), end2endNotReqd(3)  

pnniSpvcDestSusceptClip 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.13
The broadband bearer susceptability to clipping for this SPVC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

pnniSpvcDestUpTime 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.14
The time since this SPVC (Smart Permanent Virtual Circuits) was created in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

pnniSpvcDestFwdQoSClass 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.15
The requested quality of service for this SPVC in the forward (calling to called) direction.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER class0(1), class1(2), class2(3), class3(4), class4(5)  

pnniSpvcDestBckQoSClass 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.16
The requested quality of service for this SPVC in the backward (called to calling) direction.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER class0(1), class1(2), class2(3), class3(4), class4(5)  

pnniSpvcDestTransitNetSel 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.17
The optional transit network selection for this SPVC.
Status: current Access: read-only
OBJECT-TYPE    
  TransitNetwork  

pnniSpvcDestStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.18
The operational status of this SPVC (Smart Permanent Virtual Circuit).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), failed(3)  

pnniSpvcDestRGroupIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.19
This specifies the entry in the Spvxc Redundancy Group table for information regarding the secondary port to be used as the redundant port. This will used at the terminating PVC end.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

pnniSpvcParamGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.7
OBJECT IDENTIFIER    

pnniSpvcPaceInterval 1.3.6.1.4.1.326.2.2.2.1.6.2.7.1
The time interval between successive callbacks to the SPVC controller to open to the destinations of a batch of SPVCs
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval  

pnniSpvcPaceNumSpvcs 1.3.6.1.4.1.326.2.2.2.1.6.2.7.2
The max number of SPVCs that each batch of SPVCs that the SPVC controller tries to open to per pnniSpvcPaceInterval
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pnniSpvcRerouteInterval 1.3.6.1.4.1.326.2.2.2.1.6.2.7.3
The time interval between successive callbacks to the SPVC controller to reroute existing SPVC connection if a better path is available to the destination
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval  

pnniSpvcRerouteNumSpvcs 1.3.6.1.4.1.326.2.2.2.1.6.2.7.4
The number of SPVCs that are attempted to be rerouted by the SPVC controller per pnniSpvcRerouteInterval
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pnniSpvcRerouteThreshold 1.3.6.1.4.1.326.2.2.2.1.6.2.7.5
The percentage improvement in the cost that the new SPVC path must have over the current SPVC path before a reroute will be performed.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pnniSpvcLowestPriority 1.3.6.1.4.1.326.2.2.2.1.6.2.7.6
The value of lowest priority for SPVCCs
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pnniSpvcDefaultUbrBandwidth 1.3.6.1.4.1.326.2.2.2.1.6.2.7.7
The default bandwidth in Kilo-CPS to be used for UBR SPVCs
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65534  

pnniSpvcBackoffInterval 1.3.6.1.4.1.326.2.2.2.1.6.2.7.9
The time interval to backoff a DTL that failed call setup. The DTL will not be used again until this interval has elapsed. The interval will not be applicable if backoff is disabled on the SPVC.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval  

pnniSpvcTrapMode 1.3.6.1.4.1.326.2.2.2.1.6.2.7.8
This configuration item specifies whether the switch should send the: spvcRerouteInitiated OR pnniSpvccUp and pnniSpvccFail OR pnniSpvccDown, pnniSpvccFail, and pnniSpvccUp traps.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reroute(1), failure(2), all(3), none(4)  

pnniPmpSpvcPartyPaceNum 1.3.6.1.4.1.326.2.2.2.1.6.2.7.10
The maximum number parties within a PMP SPVC that are activated per SpvcPacingInterval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pnniSpvpcParamGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.8
OBJECT IDENTIFIER    

pnniSpvpcPaceInterval 1.3.6.1.4.1.326.2.2.2.1.6.2.8.1
The time interval between successive callbacks to the SPVPC controller to open connections to the destinations of a batch of SPVPCs. This parameter along with pnniSpvpcPaceNumSpvpcs control the rate at which the SPVPCs that are down are established. Analogous SPVCC variable is pnniSpvcPaceInterval.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval  

pnniSpvpcPaceNumSpvpcs 1.3.6.1.4.1.326.2.2.2.1.6.2.8.2
The max number of SPVPCs that the SPVPC controller tries to activate per pnniSpvpcPaceInterval. This controls the rate at which SPVPCs that are down are established. The corresponding SPVCC variable is pnniSpvcPaceNumSpvcs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1000  

pnniSpvpcRerouteInterval 1.3.6.1.4.1.326.2.2.2.1.6.2.8.3
The time interval between successive callbacks to the SPVPC controller to reroute existing SPVPC connections if a better path is available to the destination. This is one of the parameters that control the rate at which rerouting is attempted. The analogous SPVCC variable is pnniSpvcRerouteInterval.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval  

pnniSpvpcRerouteNumSpvpcs 1.3.6.1.4.1.326.2.2.2.1.6.2.8.4
The number of SPVPCs that are attempted to be rerouted by the SPVPC controller per pnniSpvpcRerouteInterval. Thus it determines the rerouting rate. The analogous SPVCC variable is pnniSpvcRerouteNumSpvcs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1000  

pnniSpvpcRerouteThreshold 1.3.6.1.4.1.326.2.2.2.1.6.2.8.5
The percentage improvement in the cost that the new SPVPC path must have over the current SPVPC path before a reroute will be performed. This is analogous to the pnniSpvcRerouteThreshold variable for SPVCCs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

pnniSpvpcLowestPriority 1.3.6.1.4.1.326.2.2.2.1.6.2.8.6
The value of lowest priority for SPVPCs
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pnniSpvpcTrapMode 1.3.6.1.4.1.326.2.2.2.1.6.2.8.7
This configuration item specifies whether the switch should send the: spvcRerouteInitiated OR pnniSpvpcUp and pnniSpvpcFail OR pnniSpvpcDown, pnniSpvpcFail, and pnniSpvpcUp traps.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reroute(1), failure(2), all(3), none(4)  

pnniSpvpcBackoffInterval 1.3.6.1.4.1.326.2.2.2.1.6.2.8.8
The time interval to backoff a DTL that failed call setup. The DTL will not be used again until this interval has elapsed. The interval will not be applicable if backoff is disabled on the SPVPC.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval  

pnniSpvpcSrcTable 1.3.6.1.4.1.326.2.2.2.1.6.2.9
This table contains information about SPVPCs (Smart Permanent Virtual Path Connections) that have their source at this switch. This table serves the same function that the pnniSpvcSrcTable serves for SPVCCs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PnniSpvpcSrcEntry

pnniSpvpcSrcEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1
A table entry containing source SPVPC (Smart Permanent Virtual Path Connection) information.
Status: current Access: not-accessible
OBJECT-TYPE    
  PnniSpvpcSrcEntry  

pnniSpvpcSrcIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.1
The value of this object uniquely identify the SPVPCs (Smart Permanent Virtual Path Connections) that have this switch as their source.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..65535  

pnniSpvpcSrcCallingPort 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.2
The value of this object identifies the input port of this SPVPC (Smart Permanent Virtual Path Connection), and is the same as the chanrInputPort, chanPort, pathPort, and portNumber. The maximum value of this variable depends on the type of the switch. The upper bound given is the highest possible as of now. In some switches the range will be much narrower.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..1025  

pnniSpvpcSrcCallingVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.3
The VPI to be used at the originating switch for the permanent portion of this SPVPC (Smart Permanent Virtual Path Connection).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvpcSrcCalledAtmAddr 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.4
The ATM address of the distant end NI (destination switch) for this SPVPC (Smart Permanent Virtual Path Connection). Distant end NI is the network interface at the destination switch at which the switched portion of this SPVPC terminates.
Status: current Access: read-create
OBJECT-TYPE    
  NsapAddr  

pnniSpvpcSrcCalledPort 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.5
The value of this object identifies the port where the permanent portion of this SPVPC (Smart Permanent Virtual Path Connection) resides at the destination switch. It has a value of -1 if this port at the destination switch cannot be determined.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvpcSrcCalledVPVCSel 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.6
The originating switch for a SPVPC can specify the VPI to be used for the permanent portion of this SPVPC at the destination switch. The value of this object indicates whether the SPVPC was configured with a specific value for this VPI or not. require(2) indicates that the user configured a specific value for this VPI and noPref(1) indicates that the user did not specify any.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER noPref(1), require(2)  

pnniSpvpcSrcCalledVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.7
The VPI to be used at the destination switch for the permanent portion of this SPVPC (Smart Permanent Virtual Path Connection). The range given above is the maximum possible. The upperbound varies with the type of netmod.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..4096  

pnniSpvpcSrcCalledAssignedVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.8
The VPI that is assigned at the destination switch for the permanent portion of this SPVPC (Smart Permanent Virtual Path Connection). This value is only meaningful if the SPVPC status is up.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

pnniSpvpcSrcFwdUpcKey 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.9
The forward UPC traffic contract key for this SPVPC. This traffic contract will be used for the data traffic flow from the originating switch to the destination switch. This key must be defined in the upcContractTable.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..32767  

pnniSpvpcSrcBckUpcKey 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.10
The backward UPC traffic contract key for this SPVPC. This traffic contract will be used for the data flow in the direction from the destination switch to the originating switch. This key must be defined in the upcContractTable.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..32767  

pnniSpvpcSrcSusceptClip 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.11
The requested broadband bearer susceptibility to clipping for this SPVPC. This object will be used to fill the broadband bearer capability information element in the call setup message for this SPVPC.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

pnniSpvpcSrcFwdQoSClass 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.12
The requested quality of service class for this SPVPC in the forward (source to destination) direction. This determines the QoS objectives for the data path from the originating switch to the destination switch.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER class0(1), class1(2), class2(3), class3(4), class4(5)  

pnniSpvpcSrcBckQoSClass 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.13
The requested quality of service class for this SPVPC in the backward (destination to source) direction. This object determines the QoS objectives for the data flow in the reverse direction (from the destination switch to the originating switch).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER class0(1), class1(2), class2(3), class3(4), class4(5)  

pnniSpvpcSrcLastFailCause 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.14
The last call setup failure cause code for this SPVPC.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

pnniSpvpcSrcRetryCount 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.15
The number of times the call setup has been attempted since the SPVPC creation or the last successful call setup for this SPVPC.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvpcSrcLastChangeTime 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.16
The time since this SPVPC (Smart Permanent Virtual Path Connection) has been up/down in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

pnniSpvpcSrcStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.17
The operational status of this SPVPC (Smart Permanent Virtual Path Connection). The value of up(1) indicates that this SPVPC is operational and down(2) indicates that the SPVPC is not-operational.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

pnniSpvpcSrcName 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.18
The value of this object identifies the name that has been assigned for this SPVPC.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

pnniSpvpcSrcRowStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.19
The status of this SPVPC (Smart Permanent Virtual Path Connection) entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pnniSpvpcSrcRouteCost 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.20
The cumulative route cost for the current route of this SPVPC (Smart Permanent Virtual Path Connection).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvpcSrcRerouteStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.21
The status of the reroute function for this SPVPC (Smart Permanent Virtual Path Connection). If set to disabled(2), no rerouting will be attempted for this SPVPC.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

pnniSpvpcSrcCallingDomain 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.22
The Domain ID identifying the routing domain to be used at the Originating Switch for this SPVPC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvpcSrcQosIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.23
The index for the QOS Class Expansion Table to be used for QoS class values into QoS parameter objectives for this SPVPC. The corresponding expansion table should be defined in the qosClassExpansionTable.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvpcSrcPriority 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.24
Priority of this SPVPC for connection
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvpcSrcLastLocation 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.25
The last call setup failure location code for this SPVPC. This indicates the switch that initiated the clearing for the call. This is formatted as a text string with the fields: FMT: Indicates diagnostic format RMT: Indicates whether a remote switch is the source of the failure or this switch inserted the location diag LINK:Link id that clear pertains to VPI: VPI that clear pertains to The remaining fields are format specific
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pnniSpvpcSrcOldRouteCost 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.26
This OID is specified only to be included the the pnniSpvcUp trap. It specifies the path cost of the call the previous time this call was up. If the call has not been up, this will report a value of -1.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvpcSrcDownReason 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.27
This OID is specified only to be included the the pnniSpvccDown and pnniSpvccFail traps. This specifies whether the SPVC call was cleared due to a better route being found, a network failure, or SPVPC deletion.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER reroute(1), failure(2), deletion(3)  

pnniSpvpcSrcBackoffStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.28
The status of the backoff function for this SPVC (Smart Permanent Virtual Path Circuit). If set to disabled(2), directed dtls configured for this SPVPC will be continually retried on failure.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

pnniSpvpcSrcActiveDtlIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.29
The Active Designated Transit List (DTL) index for this SPVPC (Smart Permanent Virtual Path Circuit). This value along with pnniSpvcSrcActiveDtlNodeIndex uniquely identifies the DTL that is currently used by the SVC portion of the SPVPC.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvpcSrcActiveDtlNodeIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.30
The Node index of the Active Designated Transit List for this SPVPC (Smart Permanent Virtual Path Circuit). The active DTL indexed by the node index and DTL index identifies the DTL that is currently used by the SVC portion of the SPVPC. The value of this object is 65535 for FTPNNI nodes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvpcSrcDtlTag 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.31
This value specifies an index into a table of DTLs, the DTL entries in this table will be used to setup the SPVPC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvpcSrcAutoDtlStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.32
The status of the dynamic path selection function for this SPVPC (Smart Permanent Virtual Path Circuit). If set to disabled(2), auto path selection will not be used.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

pnniSpvpcSrcRGroupIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.33
This specifies the entry in the Spvxc Redundancy Group table for information regarding the secondary port to be used as the redundant port
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..65535  

pnniSpvpcSrcSecondaryVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.34
The Secondary VPI to be used at the originating switch for the redundant permanent portion of this SPVPC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniSpvpcStatsGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.10
OBJECT IDENTIFIER    

pnniSpvpcSrcNumberOfSPVPCs 1.3.6.1.4.1.326.2.2.2.1.6.2.10.1
The number of SPVPCs (Smart Permanent Virtual Path Connections) that have their source at this switch. This object is analogous to the pnniSpvcSrcNumberOfSPVCs object defined for SPVCCs.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pnniSpvpcDestNumberOfSPVPCs 1.3.6.1.4.1.326.2.2.2.1.6.2.10.2
The number of connected SPVPCs (Smart Permanent Virtual Path Connections) that have their destination at this switch. This object is analogous to the pnniSpvcDestNumberOfSPVCs object for SPVCCs.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

pnniSpvpcDestTable 1.3.6.1.4.1.326.2.2.2.1.6.2.11
This table contains information about SPVPCs (Smart Permanent Virtual Path Connections) that have their destination at this switch. This table provides the same functions that the pnniSpvcDestTable provides for SPVCCs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PnniSpvpcDestEntry

pnniSpvpcDestEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.11.1
A table entry containing destination SPVPC (Smart Permanent Virtual Path Connection) information.
Status: current Access: not-accessible
OBJECT-TYPE    
  PnniSpvpcDestEntry  

pnniSpvpcDestIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.1
The value of this object uniquely identifies the SPVPCs (Smart Permanent Virtual Path Connections) that have this switch as their destination.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

pnniSpvpcDestCallingAtmAddr 1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.2
The ATM address of the calling end NI at the originating switch for this SPVPC (Smart Permanent Virtual Path Connection). Calling end NI is the network interface at the originating switch from which the switched portion of SPVPC originates.
Status: current Access: read-only
OBJECT-TYPE    
  NsapAddr  

pnniSpvpcDestCallingPort 1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.3
The value of this object identifies the port of this terminating SPVPC (Smart Permanent Virtual Path Connection) at the source switch in which the permanent portion of the SPVPC resides. It has a value of -1 if the port at the source switch cannot be determined.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1025  

pnniSpvpcDestCallingVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.4
The VPI to be used at the originating switch for the permanent portion of this SPVPC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

pnniSpvpcDestCalledAtmAddr 1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.5
The ATM address of the local end NI (at this destination switch) for this SPVPC. Local end NI is network interface at this destination switch where the switched portion of this SPVPC terminates.
Status: current Access: read-only
OBJECT-TYPE    
  NsapAddr  

pnniSpvpcDestCalledPort 1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.6
The value of this object identifies the port of this terminating SPVPC (Smart Permanent Virtual Path Connection) at this destination switch where the permanent portion of this SPVPC resides. It has a value of -1 if the port at the destination switch cannot be determined.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1025  

pnniSpvpcDestAssignedVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.7
The VPI assigned at this destination switch for the permanent portion of this SPVPC. This value is only meaningful if the SPVPC status is up.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

pnniSpvpcDestSusceptClip 1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.8
The value of this object identifies if the SPVPC was setup with the broadband bearer susceptibility to clipping set or not.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

pnniSpvpcDestUpTime 1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.9
The time since this SPVPC (Smart Permanent Virtual Path Connection) was created in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

pnniSpvpcDestFwdQoSClass 1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.10
The requested quality of service class for this SPVPC in the direction from the source switch to the destination switch. This value determines the QoS parameter objectives for this SPVPC in that direction.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER class0(1), class1(2), class2(3), class3(4), class4(5)  

pnniSpvpcDestBckQoSClass 1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.11
The requested quality of service class for this SPVPC in the direction from the destination switch to the source switch. This value determines the QoS objectives for the data flow in that direction.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER class0(1), class1(2), class2(3), class3(4), class4(5)  

pnniSpvpcDestStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.12
The operational status of this SPVPC (Smart Permanent Virtual Path Connection). up(1) indicates that this SPVPC is operational while down(2) indicates that it is not.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

pnniSpvpcDestRGroupIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.13
This specifies the entry in the Spvxc Redundancy Group table for information regarding the secondary port to be used as the redundant port. This will used at the terminating PVC end.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

pnniPmpSpvccGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.12
OBJECT IDENTIFIER    

pnniPmpSpvccSrcNextRootIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.12.1
The index of the next free root index in the pnniPmpSpvcSrcRootTable. Client is responsible for implementing a policy when a set on this variable fails. E.g. Keep testing this variable until a free index is found or choose a random number or a combination of the two.
Status: current Access: read-write
OBJECT-TYPE    
  TestAndIncr  

pnniPmpSpvccSrcNumberOfSpvccs 1.3.6.1.4.1.326.2.2.2.1.6.2.12.2
The number of PMP SPVCCs (Smart Permanent Virtual Circuits) that have their source at this switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcRootTable 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3
This table contains information about the root side of PMP SPVCCs (Smart Permanent Virtual Circuits) that have their source at this switch. It also contains the connection parameters that are common to all the parties
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PnniPmpSpvccSrcRootEntry

pnniPmpSpvccSrcRootEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1
A table entry containing source PMP SPVCC (Smart Permanent Virtual Circuits) information.
Status: current Access: not-accessible
OBJECT-TYPE    
  PnniPmpSpvccSrcRootEntry  

pnniPmpSpvccSrcRootIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.1
The value of this object uniquely identify the PMP SPVCCs (Smart Permanent Virtual Circuits) that have this switch as their source(root).
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcRootPort 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.2
The value of this object identifies the input port of this PMP SPVCC (Smart Permanent Virtual Circuits), and is the same as the chanrInputPort, chanPort, pathPort, and portNumber.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcRootVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.3
The VPI to be used at the Calling(root) NI for this PMP SPVCC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcRootVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.4
The VCI to be used at the Calling(root) NI for this PMP SPVCC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcRootFwdUpcKey 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.5
The forward UPC traffic contract key for this PMP SPVCC. This key must be defined in the upcContractTable. Backward UPC traffic contract does not apply to PMP SPVCCs.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcRootBearerClass 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.6
The requested broadband bearer class for this PMP SPVCC.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER classA(1), classC(2), classX(3)  

pnniPmpSpvccSrcRootSusceptClip 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.7
The requested broadband bearer susceptability to for this PMP SPVCC.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

pnniPmpSpvccSrcRootFwdQoSClass 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.8
The requested quality of service for this PMP SPVCC in the forward (calling to called) direction. Backward direction does not apply to PMP SPVCCs.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER class0(1), class1(2), class2(3), class3(4), class4(5)  

pnniPmpSpvccSrcRootStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.9
The operational status of this PMP SPVCC (Smart Permanent Virtual Circuit).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), wait(3)  

pnniPmpSpvccSrcRootName 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.10
The value of this object identifies the name that has been assigned for this PMP SPVCC.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

pnniPmpSpvccSrcRootPriority 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.11
Priority of this PMP SPVCC for connection. This priority is shared with any point-to-point SPVCCs configured on this switch.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcRootNumberOfParties 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.12
Number of parties currently configured with this PMP SPVCC
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcRootNextPartyIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.13
This indicates the next allocatable party index
Status: current Access: read-create
OBJECT-TYPE    
  TestAndIncr  

pnniPmpSpvccSrcRootCallingDomain 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.14
The Domain ID to be used at the Calling NI for this PMP SPVCC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcRootRowStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.15
The status of this SPVCC (Smart Permanent Virtual Circuits) entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pnniPmpSpvccSrcRootRGroupIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.16
This specifies the entry in the Spvxc Redundancy Group table for information regarding the secondary port to be used as the redundant port
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..65535  

pnniPmpSpvccSrcRootSecondaryVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.17
The Secondary VPI to be used at the originating switch for the redundant permanent portion of this SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcRootSecondaryVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.18
The Secondary VCI to be used at the originating switch for the redundant permanent portion of this SPVC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcPartyTable 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4
This table contains information about the parties of PMP SPVCCs (Smart Permanent Virtual Circuits) that have their source at this switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PnniPmpSpvccSrcPartyEntry

pnniPmpSpvccSrcPartyEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1
A table entry containing information about parties in a PMP SPVCC (Smart Permanent Virtual Circuits) at the source.
Status: current Access: not-accessible
OBJECT-TYPE    
  PnniPmpSpvccSrcPartyEntry  

pnniPmpSpvccSrcPartyIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.1
The value of this object uniquely identifies a party within a PMP SPVCC identified by pnniPmpSpvccSrcRootIndex. Root's parameters and commmon connection parameters for this party are availabe in pnniPmpSpvccSrcRootTable, indexed by pnniPmpSpvccSrcRootIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcPartyAtmAddr 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.2
The ATM address of the distant end NI (remote switch) for this party.
Status: current Access: read-create
OBJECT-TYPE    
  NsapAddr  

pnniPmpSpvccSrcPartyVPVCSel 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.3
The Called VPI/VCI value selection qualifier.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER noPref(1), require(2)  

pnniPmpSpvccSrcPartyVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.4
The VPI to be used at the Called NI for this party.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcPartyVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.5
The VCI to be used at the Called NI for this party.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcPartyAssignedVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.6
The VPI assigned at the Called NI for this party. This value is only meaningful if the party status is up.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcPartyAssignedVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.7
The VCI assigned at the Called NI for this party. This value is only meaningful if the party status is up.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcPartyStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.8
Operational status of this party in the PMP SPVCC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), connecting(3)  

pnniPmpSpvccSrcPartyName 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.9
The value of this object identifies the name that has been assigned for this party.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

pnniPmpSpvccSrcPartyLastFailCause 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.10
The last setup(addparty) failure cause code for this party.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pnniPmpSpvccSrcPartyRetryCount 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.11
The number of times the party setup/addparty has been attempted since the party creation or the last successful setup/addparty.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcPartyLastChangeTime 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.12
The time since this party has been up/down in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

pnniPmpSpvccSrcPartyFtDtlIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.13
The Designated Transit List (DTL) index for this party. This value must be defined in the ftPnniDTLTable. The DTL specifies a preferred call routing for the SVC portion of the party. If a DTL is specified, this party will not be rerouted when rerouting is requested administratively.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcPartyRerouteStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.14
The status of the reroute function for this party. Rerouting can be administratively requested, for active parties, by setting this variable to reroute_requested(2). On successful completion of rerouting, it will be set to reroute_completed(3). When a DTL is specified for a party, rerouting will not be performed for that party and this variable will set to reroute_not_applicable.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER rerouteNotRequested(1), rerouteRequested(2), rerouteCompleted(3), rerouteNotApplicable(4)  

pnniPmpSpvccSrcPartyQosIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.15
The index for the QOS Class Expansion Table to be used for this PMP SPVCC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccSrcPartyRowStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.16
The status of this party entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pnniPmpSpvccSrcPartyLastLocation 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.17
The last call setup failure location code for this SPVC. This indicates the switch that initiated the clearing for the call. This is formatted as a text string with the fields: FMT: Indicates diagnostic format RMT: Indicates whether a remote switch is the source of the failure or this switch inserted the location diag LINK:Link id that clear pertains to VPI: VPI that clear pertains to The remaining fields are format specific
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pnniPmpSpvccSrcPartyAutoDtlStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.18
The status of the dynamic path selection function for this SPVC (Smart Permanent Virtual Circuit). If set to disabled(2), auto path selection will not be used.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

pnniPmpSpvccSrcPartyDownReason 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.19
The reason for the spvc down is set accordingly
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER reroute(1), failure(2), deletion(3)  

pnniPmpSpvccSrcPartyRouteCost 1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.20
The link cost associated for the party isset here
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccDestNumberOfSpvccs 1.3.6.1.4.1.326.2.2.2.1.6.2.12.5
The number of connected PMP SPVCCs (Smart Permanent Virtual Circuits) that have their parties terminating at this switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccDestRootTable 1.3.6.1.4.1.326.2.2.2.1.6.2.12.6
This table contains information about the root of PMP SPVCCs (Smart Permanent Virtual Circuits) that have their parties terminating at this switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PnniPmpSpvccDestRootEntry

pnniPmpSpvccDestRootEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1
A table entry containing destination SPVCC (Smart Permanent Virtual Circuits) information.
Status: current Access: not-accessible
OBJECT-TYPE    
  PnniPmpSpvccDestRootEntry  

pnniPmpSpvccDestRootIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.1
The value of this object uniquely identifies the PMP SPVCCs (Smart Permanent Virtual Circuits) that has one or more parties terminating at this switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccDestRootAtmAddr 1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.2
The ATM address of the root of the PMP SPVCC that has one or more parties terminating at this switch.
Status: current Access: read-only
OBJECT-TYPE    
  NsapAddr  

pnniPmpSpvccDestRootPort 1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.3
The value of this object identifies the port of this terminating PMP SPVCC (Smart Permanent Virtual Circuits) at the source end. It has a value of -1 if the port at the destination switch cannot be determined.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccDestRootVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.4
The VPI used for the PVCC portion of the connection at the root of the PMP SPVCC. The root switch is identified by pnniPmpSpvccDestCallingAtmAddr.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccDestRootVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.5
The VCI used for the PVCC portion of the connection at the root of the PMP SPVCC. The root switch is identified by pnniPmpSpvccDestCallingAtmAddr.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccDestRootBearerClass 1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.6
The broadband bearer class signalled for the first party of this PMP SPVCC. All subsequent parties should have the same value.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER classA(1), classC(2), classX(3)  

pnniPmpSpvccDestRootSusceptClip 1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.7
The broadband bearer susceptability to clipping signalled for the first party of this PMP SPVCC. All subsequent parties should have the same value.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

pnniPmpSpvccDestRootFwdQoSClass 1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.8
The requested quality of service for this PMP SPVCC in the forward (from root to leaves) direction. Backward QoS requirements do not apply to PMP SPVCCs.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER class0(1), class1(2), class2(3), class3(4), class4(5)  

pnniPmpSpvccDestRootNumberOfParties 1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.9
Number of parties currently terminating at this switch within this PMP SPVCC
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccDestPartyTable 1.3.6.1.4.1.326.2.2.2.1.6.2.12.7
This table contains information about the parties of PMP SPVCCs (Smart Permanent Virtual Circuits) that terminate at this switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PnniPmpSpvccDestPartyEntry

pnniPmpSpvccDestPartyEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1
A table entry containing destination information about parties in a PMP SPVCC (Smart Permanent Virtual Circuits).
Status: current Access: not-accessible
OBJECT-TYPE    
  PnniPmpSpvccDestPartyEntry  

pnniPmpSpvccDestPartyIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.1
The value of this object uniquely identifies a party of PMP SPVCCs (Smart Permanent Virtual Circuits) that have one or more parties terminating at this switch. This value is unique within a PMP SPVCC represented by pnniPmpSpvccDestRootIndex
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccDestPartyAtmAddr 1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.2
The ATM address of the switch where this party of a PMP SPVCC terminates.
Status: current Access: read-only
OBJECT-TYPE    
  NsapAddr  

pnniPmpSpvccDestPartyPort 1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.3
The value of this object identifies the port where this party of a PMP SPVCC (Smart Permanent Virtual Circuits) terminates.It has a value os -1 if the port at the destination switch cannot be determined.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccDestPartyAssignedVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.4
The value of this object identifies the VPI assigned for this party of a PMP SPVCC (Smart Permanent Virtual Circuits) at the terminating switch. This value is only meaningful if the party status, identified by pnniPmpSpvccDestStatus, is up.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccDestPartyAssignedVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.5
The value of this object identifies the VCI assigned for this party of a PMP SPVCC (Smart Permanent Virtual Circuits) at the terminating switch. This value is only meaningful if the party status, identified by pnniPmpSpvccDestStatus, is up.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniPmpSpvccDestPartyUpTime 1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.6
The time since this party of PMP SPVCC (Smart Permanent Virtual Circuits) was created in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

pnniPmpSpvccDestPartyTransitNetSel 1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.7
The optional transit network selection for this party of PMP SPVCC.
Status: current Access: read-only
OBJECT-TYPE    
  TransitNetwork  

pnniPmpSpvccDestPartyStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.8
The operational status of this party of PMP SPVCC (Smart Permanent Virtual Circuit).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), failed(3)  

pnniPmpSpvccDestPartyRGroupIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.9
This specifies the entry in the Spvxc Redundancy Group table for information regarding the secondary port to be used as the redundant port. This will used at the terminating PVC end.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

pnniSpvxcRGroupTable 1.3.6.1.4.1.326.2.2.2.1.6.2.14
A table of Primary to Secondary Port mappings that will be used for redundancy in permanent portion of SPVxCs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PnniSpvxcRGroupEntry

pnniSpvxcRGroupEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.14.1
A table entry containing the primary to secondary port mappings.
Status: current Access: not-accessible
OBJECT-TYPE    
  PnniSpvxcRGroupEntry  

pnniSpvxcRGroupIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.1
The value of this object identifies the Group Index associated with this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..65535  

pnniSpvxcRGroupPrimaryPort 1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.2
The value of this object identifies the primary port of this entry. This will used as the primary PVC port for the SPVC created with this group index.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pnniSpvxcRGroupSecondaryPort 1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.3
The value of this object identifies the secondary port of this group. This will used as the redundant PVC port for the SPVC created with this group index. During a switch command, the PVCs will be switched from primary port to this port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pnniSpvxcRGroupNsapAddr 1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.4
This shows the default nsap address associated with this group using the default domain's prefix. This is a read-only variable available to view the default nsap address associated with this group.
Status: current Access: read-only
OBJECT-TYPE    
  NsapAddr  

pnniSpvxcRGroupSwitchoverCmd 1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.5
The value of this MIB defines the switchover command. The value of 1 is used to switch over the permanent PVC portion to the primary port. The value of 2 is used to switch over the permanent PVC portion to the secondary port. If the permanent portions are already on the specified port, no action is taken
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER switch2primary(1), switch2secondary(2)  

pnniSpvxcRGroupActivePort 1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.6
This specifies the port that is active. This can take any one of the primary or secondary port values. This is a read only variable useful to check the currently active port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

pnniSpvxcRGroupPacingNumber 1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.7
This specifies the pacing number for this group. During a pacing interval, pacing number of SPVCs will be attempted for PVC switch over.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pnniSpvxcRGroupPacingInterval 1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.8
This specifies the pacing interval in units of milliseconds for this group. Every time a switchover command is issued, pacing number of SPVCs will be attempted for PVC switch over every Pacing Interval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pnniSpvxcRGroupAutoPVCSwitchover 1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.9
The value of this MIB defines if automatic switchover of the PVC portion is enable dor disabled. The default value is disabled(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

pnniSpvxcRGroupName 1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.10
The value of this object identifies the name that has been assigned for this Rgroup.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

pnniSpvxcRGroupState 1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.11
This specifies the state of the Redundancy Group. State operational(1) indicates that this group is in the normal state and switchover is not going on. State switchover_in_progress(2) indicates that switchover is presently going on for this group. In this state no new SPVCs can be added to this group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER operational(1), switchoverInProgress(2)  

pnniSpvxcRGroupRowStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.12
The status of this pnniSpvxcRGroup entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

q2931AdminTable 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1
A table of general information about the Q2931 signaling path.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Q2931AdminEntry

q2931AdminEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1
A table entry containing Q2931Admin signaling administration information, indexed by port and path.
Status: current Access: not-accessible
OBJECT-TYPE    
  Q2931AdminEntry  

q2931AdminPort 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.1
The value of this object identifies the port of this signalling path, and is the same as the portNumber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931AdminVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.2
The VPI (Virtual Path Identifier) of this signaling path.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931AdminVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.3
The VCI (Virtual Channel Identifier) of the signaling channel within the signaling path.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931AdminStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.4
The desired state of this signaling channel. The up(1) state dictates that Q2931 messages are used for signalling. The down(2) state dictates that Q2931 protocol is not used for signalling.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

q2931OperStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.5
The current operational state of this signaling channel, as determined either by administrative action, when the value of q2931AdminStatus is down(2), or by a link monitoring protocol, when the value of q2931AdminStatus is up(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

q2931SSCOPOperStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.6
The current operational state of the underlying SSCOP (Service Specific Connection Orientedd Protocol) on this channel. SSCOP's function is to provide a reliable data link layer for the exchange of Q.2931 signalling messages. The value up(1) reflects the value dataTransReady(4) for the SSCOPOperStatus object in the SSCOP Administration table (sscopAdminTable). All other values of that object are reflected as the value down(2) for this object.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

q2931ILMIAdminStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.7
The desired state of the underlying ILMI (Interim Local Manageemnt Interface) status and configuration channel. The up(1) state dictates that ILMI messages are used for status and configuration information. The down(2) state dictates that ILMI protocol is not used.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

q2931ILMIOperStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.8
The current operational state of the underlying ILMI (Interim Local Manageemnt Interface) status and configuration channel, as determined either by administrative action, when the value of q2931ILMIAdminStatus is down(2), or by a link monitoring protocol, when the value of q2931ILMIAdminStatus is up(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

q2931AdminAALType 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.9
The AAL (ATM Adaptation Layer) type that is used by this Q2931 signaling path.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER type34(1), type5(2)  

q2931AdminUNISide 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.10
This object detemines the role this port takes in the UNI (User Network Interface). If this port is connected to a host via the private UNI, this port is on the network(2) side of the UNI, whilst if this port is connected to the Public UNI the port may be required to be the user(1) side of the connection.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER user(1), network(2)  

q2931AdminConfigType 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.11
The configuration of the UNI (User Network Interface) at initialization. Configuring the UNI to publicUNI(1) means that this link will be used between the switch and a public switch. Configuring the UNI to automode(2) means that the operational type will be determined dynamically. Configuring the UNI to iisp(3) (Interim Inter-Switch Signalling Protocol) indicates that this link is used for static routing NNI (Network to Network Interface). Configuring the type to privateNNI allows the interface to come up as PNNI type and running the PNNI routing protocol. Configuring the type as privateUNI indicates that the interface should comeup as a user-network interface UNI.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER publicUNI(1), automode(2), iisp(3), ftPNNI(4), privateNNI(5), privateUNI(6)  

q2931AdminOperType 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.12
The operational configuration of the UNI (User Network Interface). publicUNI(1) is used between the switch and a public switch. privateUNI(2) is used between the switch and a host. IISP, iisp(3), stands for Interim Inter-Switch Signalling Protocol, is used between two switches using static routing. And spansNNI(4) is used between two switches using SPANS mapping messages for dynamic routing. If the q2931AdminConfigType is set to auto(2), the value of this object may be either privateUNI(2), or spansNNI(4).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER publicUNI(1), privateUNI(2), iisp(3), ftPNNI(4), privateNNI(5)  

q2931AdminEntryStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.13
The status of this signaling path entry. Setting this object to invalid(4) causes the q2931 path to be destroyed.
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

q2931AdminRemoteIpAddress 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.14
The IP address of the entity connected to this q2931 signalling path. The remote IP address is derived using ILMI on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

q2931SigReservedBW 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.15
Bandwidth reserved for the UNI Signaling VC, in cells/sec.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

q2931ILMIReservedBW 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.16
Bandwidth reserved for the UNI ILMI VC, in cells/sec.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

q2931ILMIAdminVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.17
The VCI (Virtual Channel Identifier) of the ILMI signalling channel.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931AdminMinVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.18
The minimum configured VCI (Virtual Channel Identifier) used for SVCs (Signalling Virtual Circuits).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931AdminMaxVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.19
The maximum configured VCI (Virtual Channel Identifier) used for SVCs (Signalling Virtual Circuits).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931MinVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.20
The minimum actual VCI (Virtual Channel Identifier) used for SVCs (Signalling Virtual Circuits).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931MaxVCI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.21
The maximum actual VCI (Virtual Channel Identifier) used for SVCs (Signalling Virtual Circuits).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931UNIConfigVersion 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.22
The configuration version of the UNI protocol to use at initialization. Configuring the UNI to auto(1), means that the UNI will attempt to automatically determine which version of the UNI protocol to use by reading the value of ILMI variable atmfAtmLayerUniVersion. Configuring the UNI to uni30(2) means that this link will use version 30 of the UNI protocol, likewise for uni31(3). If the nni interface has to be brought up as pnni then pnni10 version isspecified. To bring the interface as uni40 version then sepcify uni40.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER auto(1), uni30(2), uni31(3), pnni10(4), uni40(5)  

q2931UNIOperVersion 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.23
The version of the UNI that is currently being used on this link, i.e. the operational version of the UNI.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER auto(0), uni30(1), uni31(2), pnni10(3), uni40(4)  

q2931ILMIRegistration 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.24
Whether to do ILMI Address and Prefix Registration across this UNI. If disabled, no prefix registration messages are sent by the network-side, and no address registration messages are generated by the user-side. If set to ignore, then the network-side performs as it normally would, except that addresses registered are not published into the routing database. This setting is not recommended except in Public Network situations where CPE equipment requires ILMI Address registration in order to function correctly. The default value of this variable is different depending on the type of UNI being created. If creating a public UNI, this variable defaults to disable, while it defaults to enable for all other types.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2), ignore(3)  

q2931CallingPDefaultAddress 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.25
The calling party address to be inserted in Connection Setup messages which do not contain Calling Party Addresses.
Status: current Access: read-create
OBJECT-TYPE    
  NsapAddr  

q2931AdminUseNativeE164 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.26
Whether to use Native Form of E164 Addresses across this link. Used by Public UNI.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

q2931AdminNativeE164Address 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.27
Native E164 Address for this uni.
Status: current Access: read-create
OBJECT-TYPE    
  E164Address  

q2931AdminE164AddressResolution 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.28
Whether to resolve Private NSAPs into Native E164 addresses (using the Q2931E164AddrResTable). If disabled, but if q2931AdminUseNativeE164 is enabled, then the only address conversion performed at this UNI will be of Private NSAPs in E.164 format.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

q2931AdminFtPnniOrigCost 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.29
The cost of each pnni orig loglink. It is configured at originating end of sigpath
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER 1..4294967295  

q2931AdminFtPnniTermCost 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.30
The cost of each pnni term loglink. The originating side of a link informs the terminating side of the configured q2931AdminFtPnniOrigCost in a hello message. The terminating side then uses the cost value in the hello message as the q2931AdminFtPnniTermCost for topology advertisement.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

q2931AdminAVPresentation 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.31
The set of Address Validation interface options as follows: (The bits in this integer have the following meanings:) Bit Significance Default ======== ============= ======== 0x0001 Address Validation Enabled disabled 0x0002 insertCallingPDefaultAddress disabled 0x0004 CallingP_delivery enabled 0x0008 CallingPSubAddr_trxf enabled 0x0010 CalledPSubAddr_trxf enabled 0x0020 BHLI_TRXF enabled 0x0040 BLLI_TRXF enabled 0x0080 BLLI_selection_TRXF enabled 0x0100 AAL_INFO_TRXF enabled --- Not used presently. ----
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

q2931AdminSigMode 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.32
The configured mode for signalling: VP-associated, Non-Associated or auto mode. vpAssoc(1) stands for VP-associated signalling, if set to this value, the uni encodes the connection identifier with the VP-associated signalling bits. nonAssoc(2) is for Non-associated signalling, if set to this value the connection identifier is encoded with non-associated signalling bits. auto(3) stands for auto-configured signalling mode, if set to this value, the operating mode will be determined dynamically and will either be VP-associated or Non-associated depending on the operating type of the signalling link
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER vpAssoc(1), nonAssoc(2), auto(3)  

q2931AdminSigAlloc 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.33
The current configured allocation policy for a network side uni. If set to allocVP(1), the signalling entity will allocate connections within the containing VP only. If set to allocLink(2), the signalling entity will allocate connections in its containing VP and may allocate connections in other VPS that are available to it. If set to allocVpBundle, the uni will allocate connections in its containing VP and a bundle of other VPs which are pre-created. If set to auto(3), the operating allocation policy will be determined based on the operating type of the signalling entity and the VPI value of the VP in which the signalling channel is present. Based on these, it might be allocLink or allocVP or allocVpBundle
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER allocVP(1), allocLink(2), auto(3), allocVpBundle(4), allocProxy(5)  

q2931PeerPort 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.34
The value of this object identifies the port of the peer's signalling path. The value starts at zero.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931InputSigContract 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.35
Traffic Contract to be applied to the input signalling channel.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931OutputSigService 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.36
Service Queue where the output signalling vc should be inserted into.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER vbr(1), ubr(2), unknown(3)  

q2931SSCOPNoRespTimer 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.37
The Value to be set for the duration of the SSCOP No response timer. This is the time in seconds that we will wait before bringing the SSCOP link down. If no value is specified by the user, a default value of 10 seconds is used if the oper version is uni30 and a default value of 7 secs is used if the oper version is uni31.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931AdminIncomingNSAPFilterIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.46
The Filter Index of the NSAP Address Filter used to filter incoming calls. If this variable is set to zero, all incoming calls on this UNI will be accepted.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931AdminOutgoingNSAPFilterIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.47
The Filter Index of the NSAP Address Filter used to filter outgoing calls. If this variable is set to zero, all incoming calls on this UNI will be accepted.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931AdminIEFilter 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.48
The set of Information Element Filtering interface options as follows: (The bits in this integer have the following meanings:) Bit Significance Default ======== ============= ======== 0x0001 IE Filtering enabled disabled 0x0002 InsertCallingPDefaultAddress disabled 0x0004 CallingP_delivery enabled 0x0008 CallingPSubAddr_trxf enabled 0x0010 CalledPSubAddr_trxf enabled 0x0020 BHLI_trxf enabled 0x0040 BLLI_trxf enabled 0x0080 BLLI_selection_trxf enabled 0x0100 AAL_Info_trxf enabled --- not used presently ---- The valid combinations of bits 0x40 (BLLI_TRXF) and 0x80 (BLLI_selection_TRXF) are: 0xc0 (1 1) transfer all BLLIs default 0x80 (1 0) **invalid** 0x40 (0 1) transfer only the first BLLI 0x00 (0 0) remove all BLLIs
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931SendCallProc 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.49
A flag which allows the user to specify at creation time if CALL PROCEEDING should be sent on this particular interface. If set to on(1), a CALL PROCEEDING message is sent out that interface for every SETUP received on that interface that is successfully forwarded. If set to off(2), no CALL PROCEEDING messages are sent on this interface.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

q2931VCIRangeStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.51
A flag which indicates the status of Min/MaxVCI range with respect to whether or not the range values are assigned after negotiating with the peer through ILMI process. This variable is set to valid if ILMI is up and range negotiation with the peer is completed, except if a UNI (link) is configured as IISP or ILMI-down, then the value of this MIB value is always set to valid.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

q2931ClearOnCarrierLoss 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.52
This object indicates whether to clear calls when carrier is lost on the link associated with this signalling channel. The default value is noClear(1). This follows the ATM Forum specification which requires the specific signalling timers to expire before clearing the connections. Setting this value to clearCalls(2) will result in the connections being torn down as soon as carrier loss is detected (not compliant with ATM Forum signalling specifications).
Status: obsolete Access: read-create
OBJECT-TYPE    
  INTEGER noClear(1), clearCalls(2)  

q2931QosClassExpansionKey 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.54
The key for the QOS Class Expansion Table to be used for this UNI.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931AtmrConfDomainID 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.55
This is the ID of the routing domain to which this interface belongs if this uni is operating as a private UNI, public UNI or IISP
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931AtmrPnniNodeIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.56
This is the index of the node to which this interface attaches for FT-PNNI and PNNI interfaces. The value is always 0xffff for FT-PNNI interfaces.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931AdminOperSigMode 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.57
The operating mode for signalling: VP-associated or Non-associated. vpAssoc(1) stands for VP-associated signalling, if set to this value, the uni encodes the conn_id with the VP-associated signalling bits. nonAssoc(2) stands for Non-associated signalling, if set to this value, the uni encodes the conn_id with Non-associated signalling bits.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER vpAssoc(1), nonAssoc(2)  

q2931AdminOperSigAlloc 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.58
The operating allocation policy for a network side uni. If set to allocVP, the network side uni will allocate connections in its containing VP only. If set to allocLink, the uni will allocate connections in its containing VP and may allocate connections in other VPS that are available to it. If set to allocVpBundle, the uni will allocate connections in its containing VP and a bundle of other VPs which are pre-created.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER allocVP(1), allocLink(2), allocVpBundle(4), allocProxy(5)  

q2931OutputSigUpc 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.60
Traffic contract to be applied to the output side of the signalling channel. If this is not specified, signalling will be put in the vbr queue with no bandwidth reservation and no policing.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931AdminPlanType 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.61
This is the plan type to be used in calling party number and called party number IEs in the signalling messages. The value of this variable is dependent on whether q2931AdminUseNativeE164 is set to enable or disable. Further, q2931AdminPlanType can be set in conjunction with q2931AdminUseNativeE164. When q2931AdminUseNativeE164 is set to disable, q2931AdminPlanType takes a default value of 1(unknown). All other values are invalid. When q2931AdminUseNativeE164 is set to enable, q2931AdminPlanType takes a default value of 2(international). Other valid values are 3(national) and 4(subscriber).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER unknown(1), international(2), national(3), subscriber(4)  

q2931AdminMaxVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.62
The maximum configured VPI (Virtual Path Identifier) that is used for SVPs (Signalling Virtual Paths) when this interface sets up SVP Connections and also the Max VPI that is used to create dynamic paths for SVCs (Signalling Virtual Circuit) connections.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..4096  

q2931MaxSvccVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.63
The maximum actual VPI (Virtual Path Identifier) that will be used for SVCs (Signalling Virtual Circuit) dynamic paths. This variable denotes the operating value for the maximum VPI value that can be used for setting up dynamic path SVPS. The operating value can differ from the configured value (q2931AdminMaxVPI) as the operating value depends on the outcome of possible ILMI based VPI range negotiation procedure.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

q2931LastChangeTime 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.64
The time the Signalling entity was created in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

q2931MaxSvpcVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.67
The maximum actual VPI (Virtual Path Identifier) that will be used for SVPs (Signalling Virtual Paths). This variable denotes the operating value for the maximum VPI value that can be used for setting up dynamic path SVPS. The operating value can differ from the configured value (q2931AdminMaxVPI) as the operating value depends on the outcome of possible ILMI based VPI range negotiation procedure.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

q2931VpCapability 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.68
This mib variable is used to determine if this interface is capable of supporting Switched VPs. For UNI3.x and VP Scope Signalling Interfaces, SVPs (Switch Virtual Paths) cannot be created and hence undefined(1). For UNI40 & PNNI Link Scope interfaces, if there is a non-zero VPI range intersection with the peer, the interface is vpCapable(2), else notVpCapable(3)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER undefined(1), vpCapable(2), notVpCapable(3)  

q2931NNIProto 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.66
The NNI protocol being run on this link
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), ftpnni(2), forum-pnni(3), iisp(4)  

q2931AcceleratedClear 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.70
This object indicates whether to clear calls when carrier is lost on the link associated with this signalling channel or the Virtual Path goes down. The default value is noClear(1). This follows the ATM Forum specification which requires the specific signalling timers to expire before clearing the connections. Setting this value to clearCalls(2) will result in the connections being torn down as soon as carrier loss/VP failure is detected (not compliant with ATM Forum signalling specifications).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

q2931VpciGroupIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.69
The index into the VPCI Mapping Group Table to use for this signalling interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..99999  

q2931ProxyDirGroupIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.87
The index into the proxy address group table to use for this signalling interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..99999  

q2931SupplementaryServicesStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.71
This MIB variable is used to enable or disable all the supplementary services features for this interface. This acts as a global switch for this interface to disable or enable all of the supplementary services. The MIB variables defined for all supplementary services will be used only when this is enabled. The supplementary services is disabled by default. The value of undefined(3) is a read-only value used for interfaces where supplementary services are not applicable.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2), undefined(3)  

q2931CallingPAddressPresentation 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.72
The Calling party address presentation can be set to one of the two values as described above. The CLIP MIB variable is used when this interface is acting as a called party for a call setup message. When set to enable(1), while a call setup message is forwarded through this interface, the calling party number is provided. When set to disable(2), the calling party number is not provided in the call setup message. The value of undefined(3) is a read-only value used for interfaces where supplementary services are not applicable.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2), undefined(3)  

q2931CallingPAddressRestriction 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.73
The Calling party address restriction can be set to one of the two values as described above. The CLIR MIB variable is used when this interface is acting as a calling party for a call setup message. When set to enable(1), while a call setup mes-sage is received from this interface and forwarded out, the calling party number is not provided to called user. When set to disable(2), the calling party number is provided to the called user. The value of undefined(3) is a read-only value used for interfaces where supplementary services are not applicable.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2), undefined(3)  

q2931ConnectedPAddressPresentation 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.74
The Connected party address presentation can be set to one of the two values as described above. The COLP MIB variable is used when the interface is acting as a calling party to a call setup message. When set to enable(1), while a call establish-ment response message is forwarded through this interface, the connected party number is provided to the calling user. When set to disable(2), while a call establishment response message is forwarded through this interface, the connected party number is not provided to the calling user. The value of undefined(3) is a read-only value used for interfaces where supplementary services are not applicable.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2), undefined(3)  

q2931ConnectedPAddressRestriction 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.75
The Connected party address restriction can be set to one of the two values as described above. The COLR MIB variable is used when the interface is acting as a called party to a call setup message. When set to enable(1), while a call establishment response message is forwarded from this interface, the connected party number is not provided to the calling user. When set to disable(2),while a call establishment response message is forwarded from this interface, the connected party number is provided to the calling user. The value of undefined(3) is a read-only value used for interfaces where supplementary services are not applicable.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2), undefined(3)  

q2931ConnectedPDefaultAddress 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.76
The connected party address to be used in Connection Acceptance (connect, add party ack etc.) messages that do not contain Connected Party Addresses.
Status: current Access: read-create
OBJECT-TYPE    
  NsapAddr  

q2931SubaddressingAdminStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.77
This is used to enable or disable the sub-addressing capability. If this is set to enable(1), the called party sub-address IE is passed along. Ifthis is set to disbale(2), this IE is removed while forwarding the messages. The value of undefined(3) is a read-only value used for interfaces where supplementary services are not applicable.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2), undefined(3)  

q2931UserUserSignallingAdminStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.78
This is used to enable or disable the User to User Signalling capability. If this is set to enable(1), the UUS IE is passed along. If this is set to disbale(2), this IE is removed while forwarding the messages. The value of undefined(3) is a read-only value used for interfaces where supplementary services are not applicable.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2), undefined(3)  

q2931OutputIlmiUpc 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.79
The index into the UPC table for the ILMI channel
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931OutputRccUpc 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.80
The index into the UPC table for the RCC channel
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931PnniRccVci 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.81
This is used to specify the PVC RCC VCI used by PNNI. Normally this will always be 18, but if a user creates a VPT with a VCI range that does not contain 18, then this field is used to specify the PNNI PVC RCC VCI.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

q2931AdminubrCalls 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.82
This flag is used to disable processing of UBR calls.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

q2931AdmincbrCalls 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.83
This flag is used to disable processing of CBR calls.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

q2931AdminabrCalls 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.84
This flag is used to disable processing of ABR calls.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

q2931AdminrtvbrCalls 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.85
This flag is used to disable processing of RT-VBR calls.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

q2931AdminnrtvbrCalls 1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.86
This flag is used to disable processing of NRT-VBR calls.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

q2931StatsTable 1.3.6.1.4.1.326.2.2.2.1.6.2.1.2
A table of statistics about the Q2931 signaling path.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Q2931StatsEntry

q2931StatsEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1
A table entry containing signaling path statistics, indexed by port and path.
Status: current Access: not-accessible
OBJECT-TYPE    
  Q2931StatsEntry  

q2931StatsPort 1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.1
The value of this object identifies the port of this signalling path, and is the same as q2931Port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931StatsVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.2
The value of this object identifies the VPI (Virtual Path Identifier) of this signaling path statistics entry, and is the same as q2931VPI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931VCCs 1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.3
The number of Virtual Channel Connections (VCCs) on this signaling path.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

q2931Restarts 1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.4
The number of times the switch has lost and regained contact with the remote signaling entity on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

q2931CallsCompletions 1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.5
The number of successfully completed calls on this signaling path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

q2931CallsFailures 1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.6
The number of call failures on this signaling path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

q2931CallsRejections 1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.7
The number of connections on this signaling path that were rejected by the far end.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

q2931TransmittedMessages 1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.8
The total number of Q2931 messages that have been transmitted over this signalling path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

q2931ReceivedMessages 1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.9
The total number of Q2931 messages that have been received on this signalling path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

q2931PublicGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.6
OBJECT IDENTIFIER    

q2931E164AddrResTable 1.3.6.1.4.1.326.2.2.2.1.6.2.6.1
A table of E164 Address Resolution entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Q2931E164AddrResEntry

q2931E164AddrResEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.6.1.1
A table entry containing E164 Address Resolution information, indexed by Nsap.
Status: current Access: not-accessible
OBJECT-TYPE    
  Q2931E164AddrResEntry  

q2931E164Port 1.3.6.1.4.1.326.2.2.2.1.6.2.6.1.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931E164VPI 1.3.6.1.4.1.326.2.2.2.1.6.2.6.1.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931E164Nsap 1.3.6.1.4.1.326.2.2.2.1.6.2.6.1.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  NsapAddr  

q2931E164NsapMask 1.3.6.1.4.1.326.2.2.2.1.6.2.6.1.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931E164Address 1.3.6.1.4.1.326.2.2.2.1.6.2.6.1.1.5
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  E164Address  

q2931E164AddrResStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.6.1.1.6
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

q2931NSAPPingGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7
OBJECT IDENTIFIER    

q2931NPCallTable 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1
A table of NSAP addressed and call parameters to be used in testing the reachability of destination addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Q2931NPCallEntry

q2931NPCallEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1
A table entry containing NSAP address, call parameter information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Q2931NPCallEntry  

q2931NPCallIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.1
The value of this object identifies an entry in the q2931NPCallTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

q2931NPCallDstNsap 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.2
The Destination NSAP address used by this table entry.
Status: current Access: read-write
OBJECT-TYPE    
  NsapAddr  

q2931NPCallState 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.3
This field keeps the state of the nsap call. This field is set to inprogress by default. 'up' means call was successful, 'down' means call was rejected by the destination, 'err' means call was not attempted primarily because no route to destination was available, 'locpref', 'lochost' mean that the address is local
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER down(1), inprogress(2), up(3), err(4), locpref(5), lochost(6)  

q2931NPCallClientType 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.4
Holds the type of the client expected to answer the call at destination. Set to noIndication by default.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noIndication(1), lecs(2), lec(3), bus(4), les(5)  

q2931NPCallFwdUpcKey 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.6
UPC table entry to be used in the forward direction of the call is stored here. Set to ZERO by default.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931NPCallBckUpcKey 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.7
UPC table entry to be used in the backward direction of the call is stored here. Set to ZERO by default.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931NPCallCallingDomain 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.8
The domain at the originating switch on which the call has to be routed. By default this is set to the default domain, control port domain.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931NPCallQosIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.9
QOS Index entry to be used in the forward direction of the call is stored here. Set to ZERO by default.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931NPCallQosClassFwd 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.10
QOS Class for forward direction of the call. Set to ZERO by default.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(1), class1(2), class2(3), class3(4), class4(5)  

q2931NPCallQosClassBwd 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.11
QOS Class for backward direction of the call. Set to ZERO by default.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(1), class1(2), class2(3), class3(4), class4(5)  

q2931NPCallBearerClass 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.12
Bearer Class to be used for the NSAP Ping call. Set to classX by default.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER classA(1), classC(2), classX(3)  

q2931NPCallVerbose 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.13
Holds the info, whether the call setup messages have to be displayed on user console or not. By default set to off.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

q2931NPCallStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.14
The status of this table entry. This entry may not be destroyed if there are any filter entries that refer to it.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

q2931NPPingState 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.15
This field tracks the state of the ping process. Invalid is the initial state, when the connection is made the state changes to 'inprogress' and when the ping is complete the state changes to 'complete'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER invalid(0), inprogress(1), complete(2)  

q2931NPCallCauseCode 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.16
The UNI call setup failure cause code. This value is valid only if the call state is 'down'
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931NPPingPktCount 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.17
The number of ping packets used in the ping process
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931NPPingStatsPktsSent 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.18
The number of ping packets actually sent
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931NPPingStatsPktsReceived 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.19
The number of ping packets replied to by the destination
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931NPPingStatsAverageDelay 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.20
The average round trip delay expressed in milli seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931NPMeasureRoundTripDelay 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.21
Holds the info, whether the ping process has to be done after the connection is made, By default set to off
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

q2931NPPingStatsMaximumDelay 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.22
The maximum round trip delay expressed in milli seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931NPPingStatsMinimumDelay 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.23
The minimum round trip delay expressed in milli seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931NPCallNextIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.2
The index of the next free row in the q2931NPCallTable.
Status: current Access: read-write
OBJECT-TYPE    
  TestAndIncr  

q2931AddressFilterGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6
OBJECT IDENTIFIER    

q2931AFTemplateTable 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1
A table of allowable (or rejectable) NSAP source and destination addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Q2931AFTemplateEntry

q2931AFTemplateEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1
A table entry containing NSAP address filtering information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Q2931AFTemplateEntry  

q2931AFTemplateIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.1
The value of this object identifies the NSAP Address Filter Template to which this entry belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

q2931AFTemplateSrcPort 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.2
The source UNI port matched by this entry. A value of -1 matches all ports.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931AFTemplateSrcVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.3
The source UNI VPI matched by this entry. A value of -1 matches all VPIs.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931AFTemplateSrcNsap 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.4
The Source NSAP address filtered by this table entry.
Status: current Access: read-write
OBJECT-TYPE    
  NsapAddr  

q2931AFTemplateSrcNsapMask 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.5
The mask applied to the source address in order to compare against the above q2931AFTemplateEntrySrcNsap. A mask of 0 bits matches all source addresses.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931AFTemplateDstPort 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.6
The destination UNI port matched by this entry. A value of -1 matches all ports.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931AFTemplateDstVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.7
The destination UNI VPI matched by this entry. A value of -1 matches all VPIs.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931AFTemplateDstNsap 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.8
The Destination NSAP address filtered by this table entry.
Status: current Access: read-write
OBJECT-TYPE    
  NsapAddr  

q2931AFTemplateDstNsapMask 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.9
The mask applied to the destination address in order to compare against the above q2931AFTemplateDstNsap. A mask of 0 bits matches all destination addresses.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931AFTemplateAction 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.10
What to do with addresses that match this entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER accept(1), reject(2)  

q2931AFTemplateName 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.11
An optional text name for the template.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

q2931AFTemplateStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.12
The status of this table entry. This entry may not be destroyed if there are any filter entries that refer to it.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

q2931AFTemplateNextIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.2
The index of the next free row in the q2931AFTemplateTable.
Status: current Access: read-write
OBJECT-TYPE    
  TestAndIncr  

q2931AFFilterTable 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.2
A table of filters, each composed of an ordered list of address filtering templates.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Q2931AFFilterEntry

q2931AFFilterEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.2.1
A table entry for one filter.
Status: current Access: not-accessible
OBJECT-TYPE    
  Q2931AFFilterEntry  

q2931AFFilterIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.2.1.1
The value of this object identifies the NSAP Address Filter to which this entry belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

q2931AFFilterName 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.2.1.2
An optional text name for the filter.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..31)  

q2931AFFilterStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.2.1.3
The status of this table entry. Setting this variable to destroy removes this row from the q2931AFFilterTable, and removes the corresponding entries from the q2931AFFilterTListTable.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

q2931AFFilterNextIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.2.2
The index of the next free row in the q2931AFFilterTable.
Status: current Access: read-write
OBJECT-TYPE    
  TestAndIncr  

q2931AFFilterTListTable 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.3
A table of template lists for filters. A template list is composed of an ordered list of address filtering templates. All objects with the same value for q2931AFFilterIndex are conceptually part of the corresponding q2931AFFilterEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Q2931AFFilterTListEntry

q2931AFFilterTListEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.3.1
A table entry holding one template in a filter's template list.
Status: current Access: not-accessible
OBJECT-TYPE    
  Q2931AFFilterTListEntry  

q2931AFFilterTListIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.3.1.1
The value of this object identifies the order in this NSAP Address Filter in which this template is applied.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

q2931AFFilterTListTemplateIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.3.1.2
The value of this object identifies the NSAP Address Filter Template for this entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931AFFilterTListStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.3.1.3
The status of this table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

q2931AFStatsTable 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.4
A table of address filtering statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Q2931AFStatsEntry

q2931AFStatsEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.4.1
An entry in the table of address filtering statistics. There are two entries for each UNI: one for incoming call setup attempts, and one for outgoing call setup attempts.
Status: current Access: not-accessible
OBJECT-TYPE    
  Q2931AFStatsEntry  

q2931AFDirection 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.4.1.1
The value of this object identifies whether this row of the statistics table applies to incoming or outgoing call attempts.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER incoming(1), outgoing(2)  

q2931AFAccepts 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.4.1.2
The total number of Q2931 messages that have been accepted by Address Filtering on this UNI.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

q2931AFRejectKnowns 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.4.1.3
The total number of Q2931 messages that have been rejected because the supplied address matched a template in the address filtering table where the action was to reject the call.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

q2931AFRejectUnknowns 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.4.1.4
The total number of Q2931 messages that have been rejected because the supplied address matched no template in the address filtering table.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

q2931AFLookupTable 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5
The Lookup facility for NSAP address filtering.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Q2931AFLookupEntry

q2931AFLookupEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1
The result of an inquiry to the Lookup facility.
Status: current Access: not-accessible
OBJECT-TYPE    
  Q2931AFLookupEntry  

q2931AFLookupIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.1
The value of this object identifies this entry in the Filter Lookup table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

q2931AFLookupNSAPFilterIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.2
The index of the NSAP address filter for this lookup.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931AFLookupSrcPort 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.3
The simulated incoming Port for this filter lookup.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931AFLookupSrcVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.4
The simulated incoming VPI for this filter lookup.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931AFLookupSrcNsap 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.5
The Source NSAP address for this filter lookup.
Status: current Access: read-write
OBJECT-TYPE    
  NsapAddr  

q2931AFLookupDstPort 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.6
The simulated outgoing Port for this filter lookup.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931AFLookupDstVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.7
The simulated outgoing VPI for this filter lookup.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

q2931AFLookupDstNsap 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.8
The Destination NSAP address for this filter lookup.
Status: current Access: read-write
OBJECT-TYPE    
  NsapAddr  

q2931AFLookupResult 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.9
The result of a filter Lookup on the selected values: 1 Accepted 2 Rejected
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER accept(1), reject(2)  

q2931AFLookupTemplate 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.10
The index of the template in the address filter that either accepted or rejected the call. It is zero if the address was unknown.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931AFLookupStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.11
The status of this table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

q2931AFLastFailureGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6
OBJECT IDENTIFIER    

q2931AFLastFailureSrcPort 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.1
The incoming port for this failed call attempt.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931AFLastFailureSrcVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.2
The incoming VPI for this failed call attempt.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931AFLastFailureSrcNsap 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.3
The source address of this failed call attempt.
Status: current Access: read-only
OBJECT-TYPE    
  NsapAddr  

q2931AFLastFailureDstPort 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.4
The outgoing port for this failed call attempt.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931AFLastFailureDstVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.5
The outgoing VPI for this failed call attempt.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931AFLastFailureDstNsap 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.6
The destination address of this failed call attempt.
Status: current Access: read-only
OBJECT-TYPE    
  NsapAddr  

q2931AFLastFailureTemplateIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.7
The index of the template which rejected this call attempt. If this call was rejected because its addresses were not known, this field is set to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

q2931AFLastFailureDirection 1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.8
The value of this object identifies whether the incoming (source) or outgoing (destination) filter rejected the call. Its value is irrelevant for accepted calls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER incoming(1), outgoing(2)  

proxyDirMapEntryGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.15
OBJECT IDENTIFIER    

proxyDirMapEntryTable 1.3.6.1.4.1.326.2.2.2.1.6.2.15.1
A table of ATM End system address, Proxy address directory and VPCI mappings.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProxyDirMapEntry

proxyDirMapEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1
A table entry containing ATM End System Address, proxy directory group index and VPCI.
Status: current Access: not-accessible
OBJECT-TYPE    
  ProxyDirMapEntry  

proxyDirMapIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1.1
The value of this object identifies the mapping associated with this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..99999  

proxyDirMapAESA 1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1.2
The ATM End System Address associated with this entry
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

proxyDirMapGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1.3
The proxy directory address group identifier associated with this mapping
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

proxyDirMapVPCI 1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1.4
The VPCI value associated with this entry
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

proxyDirMapStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1.5
The status of this mapping entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

proxyDirMapVp 1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1.6
The VP value associated with this entry
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

proxyDirMapPort 1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1.7
The port associated with this entry
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

proxyDirGroupGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.16
OBJECT IDENTIFIER    

proxyDirGroupTable 1.3.6.1.4.1.326.2.2.2.1.6.2.16.1
A group of ATM End system address and VPCI mappings
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProxyDirGroup

proxyDirGroupEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.16.1.1
A group of ATM End system address and VPCI mappings
Status: current Access: not-accessible
OBJECT-TYPE    
  ProxyDirGroup  

proxyDirGroupIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.16.1.1.1
The value of this object identifies the mapping associated with this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..99999  

proxyDirGroupPrefix 1.3.6.1.4.1.326.2.2.2.1.6.2.16.1.1.2
The prefix of the ATM End System Address that is used in mapping to a VPCI
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

proxyDirGroupVPCIGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.16.1.1.3
The VPCI group index associated with this entry
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

proxyDirGroupStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.16.1.1.4
The status of this mapping entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

vpciMappingTableGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.13
OBJECT IDENTIFIER    

vmtVpciMapTable 1.3.6.1.4.1.326.2.2.2.1.6.2.13.1
A table of VPCI, VPI and Port mappings.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VmtVpciMapEntry

vmtVpciMapEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.13.1.1
A table entry containing a VPCI, VPI and Port mappings.
Status: current Access: not-accessible
OBJECT-TYPE    
  VmtVpciMapEntry  

vmtVpciMapIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.13.1.1.1
The value of this object identifies the VPCI mapping associated with this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..99999  

vmtVpciMapVPCI 1.3.6.1.4.1.326.2.2.2.1.6.2.13.1.1.2
The VPCI associated with this VPCI mapping entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

vmtVpciMapVPI 1.3.6.1.4.1.326.2.2.2.1.6.2.13.1.1.3
The VPI associated with this VPCI mapping entry. A value of -1 indicates that the VPI is the same as the VPI associated with the signalling interface using this VPCI mapping entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

vmtVpciMapPort 1.3.6.1.4.1.326.2.2.2.1.6.2.13.1.1.4
The Port associated with this VPCI mapping entry. A value of -1 indicates that the Port is the same as the Port associated with the signalling interface using this VPCI mapping entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

vmtVpciMapStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.13.1.1.5
The status of this VPCI mapping entry. The status cannot be set to destroy if there are any vmtVpciMapGroupTable entries that refer to it.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

vmtVpciMapGroupTable 1.3.6.1.4.1.326.2.2.2.1.6.2.13.2
A table of VPCI mapping groups. Each VPCI mapping group consists of a list if VPCI mapping entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VmtVpciMapGroupEntry

vmtVpciMapGroupEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.13.2.1
A table entry for one VPCI mapping group.
Status: current Access: not-accessible
OBJECT-TYPE    
  VmtVpciMapGroupEntry  

vmtVpciMapGroupIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.13.2.1.1
The value of this object identifies the VPCI mapping group associated with this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..99999  

vmtVpciMapGroupStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.13.2.1.2
The status of the VPCI mapping group entry. This object cannot be transitioned from the Active state to any other state if there are any signalling interfaces using this VPCI mapping group. Setting this variable to destroy will remove this row from the vmtVpciMapGroupTable and also remove the corresponding entries from the vmtVpciMapListTable.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

vmtVpciMapListTable 1.3.6.1.4.1.326.2.2.2.1.6.2.13.3
A table of VPCI mapping entries for VPCI mapping groups. A VPCI mapping list is composed of a list of VPCI mapping entries. All objects with the same value for vmtVpciMapGroupIndex are conceptually part of the same vmtVpciMapGroupEntry. Entries in this table may be added, deleted or modified only if the corresponding vpcigroup index is not being used by any signalling interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VmtVpciMapListEntry

vmtVpciMapListEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.13.3.1
A table entry holding one VPCI mapping entry in a VPCI mapping group.
Status: current Access: not-accessible
OBJECT-TYPE    
  VmtVpciMapListEntry  

vmtVpciMapListIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.13.3.1.1
The value of this object identifies the order of a VPCI mapping entry in the VPCI mapping group in which it is used.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..99999  

vmtVpciMapListMEIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.13.3.1.2
The value of this object identifies the VPCI mapping entry in the vmtVpciMapTable for this entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

vmtVpciMapListStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.13.3.1.3
The status of this entry. This object can be set to destroy only if the corresponding vmtVpciMapGroupStatus is not Active.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

perCallDbgFilterGroup 1.3.6.1.4.1.326.2.2.2.1.6.2.1.8
OBJECT IDENTIFIER    

perCallDbgFilterTable 1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1
A table of Per Call Debugging Filter entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PerCallDbgFilterEntry

perCallDbgFilterEntry 1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1.1
A table entry containing a Per Call Debugging filter.
Status: current Access: not-accessible
OBJECT-TYPE    
  PerCallDbgFilterEntry  

perCallDbgFilterIndex 1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1.1.1
The value of the object indicates the index of this entry in the PCD table. A limit will be set as a constant to limit the number of filter that can exist at once.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

perCallDbgFilterTemplateId 1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1.1.2
The value of this object reflects the index of the template to be used for this filter
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

perCallDbgFilterName 1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1.1.3
The value of this object reflects a name that will be printed out with the debug messages generated by this feature.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

perCallDbgFilterFlavor 1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1.1.4
The value of this object reflects the type of debugging that has been enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

perCallDbgFilterMatches 1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1.1.5
The value of this object reflects the number of SVC setup messages matches that have been found for this filter.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

perCallDbgFilterRowStatus 1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1.1.6
The status of this PCD filter entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

perCallDbgTransFlag 1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.2
Enables a switch to generate and print PCD debugging information when a switch receives a PCD GIT IE. The default value will be enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

nsapNetworkPrefixTable 1.3.6.1.4.1.326.2.2.2.1.9.1
A table of Network Prefix addresses
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NsapNetworkPrefixEntry

nsapNetworkPrefixEntry 1.3.6.1.4.1.326.2.2.2.1.9.1.1
An entry in the Network Prefix table.
Status: current Access: not-accessible
OBJECT-TYPE    
  NsapNetworkPrefixEntry  

nsapNetworkPrefixPort 1.3.6.1.4.1.326.2.2.2.1.9.1.1.1
The value of this object identifies the port of this signalling path, and is the same as nsapPort.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapNetworkPrefixVPI 1.3.6.1.4.1.326.2.2.2.1.9.1.1.2
The value of this object identifies the VPI (Virtual Path Identifier) of this signaling path statistics entry, and is the same as nsapVPI.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapNetworkPrefixValue 1.3.6.1.4.1.326.2.2.2.1.9.1.1.3
The network prefix for ATM addresses which is in effect on the user-side of the ATM UNI port.
Status: current Access: read-only
OBJECT-TYPE    
  NsapPrefix  

nsapNetworkPrefixStatus 1.3.6.1.4.1.326.2.2.2.1.9.1.1.4
The status of this Network Prefix entry. Setting this object to invalid(4) causes this Network to disappear.
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

nsapTopologyTable 1.3.6.1.4.1.326.2.2.2.1.9.3
A table for NSAP (Network Service Access Point) topology, based on NSAP routing.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NsapTopologyEntry

nsapTopologyEntry 1.3.6.1.4.1.326.2.2.2.1.9.3.1
An entry in the NSAP (Network Service Access Point) topology table.
Status: current Access: not-accessible
OBJECT-TYPE    
  NsapTopologyEntry  

nsapTopoBoard 1.3.6.1.4.1.326.2.2.2.1.9.3.1.1
The index of the switch board within the ATM switch cluster. This object is the same as the swBoardIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapTopoLinkSrc 1.3.6.1.4.1.326.2.2.2.1.9.3.1.2
The value of this object identifies the source NSAP (Network Service Access Point) address of this link.
Status: current Access: read-only
OBJECT-TYPE    
  NsapAddr  

nsapTopoLinkSrcMask 1.3.6.1.4.1.326.2.2.2.1.9.3.1.3
The value of this object identifies the mask that is used for the link source NSAP (Network Service Access Point) address. The mask identifies the number of bits in the NSAP address that are valid. The value of the mask object is in the range 0-160 (160 bits is the size of an NSAP address).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapTopoLinkSrcPort 1.3.6.1.4.1.326.2.2.2.1.9.3.1.4
This object identifies the physical port of the link source.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapTopoLinkSrcVpi 1.3.6.1.4.1.326.2.2.2.1.9.3.1.5
This object identifies the virtual path identifier of the link source.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapTopoLinkDest 1.3.6.1.4.1.326.2.2.2.1.9.3.1.6
The value of this object identifies the destination NSAP (Network Service Access Point) address of this link.
Status: current Access: read-only
OBJECT-TYPE    
  NsapAddr  

nsapTopoLinkDestMask 1.3.6.1.4.1.326.2.2.2.1.9.3.1.7
The value of this object identifies the mask that is used for the link destination NSAP (Network Service Access Point) address. The mask identifies the number of bits in the NSAP address that are valid. The value of the mask object is in the range 0-160 (160 bits is the size of an NSAP address).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapTopoLinkDestPort 1.3.6.1.4.1.326.2.2.2.1.9.3.1.8
This object identifies the physical port of the link destination.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapTopoLinkDestVpi 1.3.6.1.4.1.326.2.2.2.1.9.3.1.9
This object identifies the virtual path identifier of the link destination.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapTopoLinkCost 1.3.6.1.4.1.326.2.2.2.1.9.3.1.10
The routing metric for this link.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapTopoLinkUbrVCs 1.3.6.1.4.1.326.2.2.2.1.9.3.1.11
The number of UBR vcs.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Gauge32  

nsapTopoLinkCbrCapacity 1.3.6.1.4.1.326.2.2.2.1.9.3.1.12
The available capacity for additional CBR (Constant Bit Rate) connections. The available capacity is measured in Kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapTopoLinkCbrFifo 1.3.6.1.4.1.326.2.2.2.1.9.3.1.13
The size of the FIFO queue that is used for transmitting CBR (Constant Bit Rate) traffic. The size of the fifo is measured in number of cells.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapTopoLinkVbrCapacity 1.3.6.1.4.1.326.2.2.2.1.9.3.1.14
The available capacity for additional VBR (Variable Bit Rate) connections. The available capacity is measured in Kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapTopoLinkVbrFifo 1.3.6.1.4.1.326.2.2.2.1.9.3.1.15
The size of the FIFO queue that is used for transmitting VBR (Variable Bit Rate) traffic. The size of the fifo is measured in number of cells.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapTopoLinkOrig 1.3.6.1.4.1.326.2.2.2.1.9.3.1.16
The source of this route information.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER static-route(1), spans-pnni(2), ilmi-registered(3), pnni(4), external(5)  

nsapTopoLinkCapabilitySet 1.3.6.1.4.1.326.2.2.2.1.9.3.1.17
A bitmap indicate the capabilities of this link. For example, whether the link support ABR (Available Bit Rate) traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapTopoLinkFreshness 1.3.6.1.4.1.326.2.2.2.1.9.3.1.18
This object indicates the freshness (or staleness) of this NSAP (Network Service Access Point) link. As the number increases, the link becomes stale.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapTopoLinkUbrEstimatedBandwidth 1.3.6.1.4.1.326.2.2.2.1.9.3.1.19
The estimated UBR bandwidth on this link.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapStaticRouteTable 1.3.6.1.4.1.326.2.2.2.1.9.4
A table for static NSAP (Network Service Access Point) route administration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NsapStaticRouteEntry

nsapStaticRouteEntry 1.3.6.1.4.1.326.2.2.2.1.9.4.1
An entry in the NSAP (Network Service Access Point) static route administration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  NsapStaticRouteEntry  

nsapStaticRouteAddress 1.3.6.1.4.1.326.2.2.2.1.9.4.1.1
The value of this object identifies the destination NSAP address
Status: current Access: read-only
OBJECT-TYPE    
  NsapAddr  

nsapStaticRouteMask 1.3.6.1.4.1.326.2.2.2.1.9.4.1.2
The value of this object identifies the mask that is used for this NSAP (Network Service Access Point) address.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsapStaticRoutePort 1.3.6.1.4.1.326.2.2.2.1.9.4.1.3
The value of this object identifies the port through which this NSAP (Network Service Access Point) address can be reached.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

nsapStaticRouteVPI 1.3.6.1.4.1.326.2.2.2.1.9.4.1.4
The value of this object identifies the path through which this NSAP (Network Service Access Point) address can be reached.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

nsapStaticRouteCost 1.3.6.1.4.1.326.2.2.2.1.9.4.1.5
The value of this object identifies the cost associated with this Static Route. This cost is to be used as a metric while routing
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

nsapStaticRouteMaxCbrCap 1.3.6.1.4.1.326.2.2.2.1.9.4.1.6
The value of this object identifies the maximum capacity available on this route for CBR connections
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

nsapStaticRouteMaxVbrCap 1.3.6.1.4.1.326.2.2.2.1.9.4.1.7
The value of this object identifies the maximum capacity available on this route for VBR connections
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

nsapStaticRouteAbrSupport 1.3.6.1.4.1.326.2.2.2.1.9.4.1.8
The value identifies the capability to support ABR traffic on this route
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER supported(1), unsupported(2)  

nsapStaticRouteEpdSupport 1.3.6.1.4.1.326.2.2.2.1.9.4.1.9
The value identifies the capability to support Early Packet Discard (EPD) on this route
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER supported(1), unsupported(2)  

nsapStaticRouteStatus 1.3.6.1.4.1.326.2.2.2.1.9.4.1.10
The status of this NSAP (Network Service Access Point) address. Setting this object to invalid(4) causes this NSAP address to disappear.
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

ftPnniDTLTable 1.3.6.1.4.1.326.2.2.2.1.9.5
A table of Designated Transit List entries. The DTLs represent statically configured FT-PNNI routes
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FtPnniDTLEntry

ftPnniDTLEntry 1.3.6.1.4.1.326.2.2.2.1.9.5.1
An entry in the FT-PNNI DTLble. A DTL is formed by concatenating rows of the table for which the ftPnniDTLIndex is the same
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  FtPnniDTLEntry  

ftPnniDTLIndex 1.3.6.1.4.1.326.2.2.2.1.9.5.1.1
The value of this object identifies the index of a (FT-PNNI) DTL in the table. A DTL (Designated Transit List) is a source route of entries comprising a FT-PNNI node and the corresponding logical output port at that node. The FT-PNNI node is given by the node's NSAP Prefix and mask. The logical port is given by the linkid and the VPI.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

ftPnniDTLEntryIndex 1.3.6.1.4.1.326.2.2.2.1.9.5.1.2
The value of this object identifies the Index of an entry within a given DTL. A DTL is a source route and each entry in the DTL represents a single hop in the source route. Each hop is represented by a FT-PNNI node and the logical output port at that node. An entry in the DTL is given an index equal to its position in the source route. Thus the entry corresponding to the first hop is given an index of 1, the second hop an index of 2 and so on.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

ftPnniDTLNodePrefix 1.3.6.1.4.1.326.2.2.2.1.9.5.1.3
This the Prefix part of the Node ID of this DTL entry. In FT-PNNI, The Node IDs are represented as prefixes, that represents both the ID of the node and a summary of reachable addresses
Status: deprecated Access: read-create
OBJECT-TYPE    
  NsapPrefix  

ftPnniDTLNodeMask 1.3.6.1.4.1.326.2.2.2.1.9.5.1.4
This the Mask corresponding to the ftPnniDTLNodePrefix. This gives the length of the above prefix in number of bits. This can vary from 0 to 104 (13 bytes).
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER 0..104  

ftPnniDTLPort 1.3.6.1.4.1.326.2.2.2.1.9.5.1.5
This is the output port at the Node given by the above Node ID. This is also the port to which the next node in the DTL (if there is one) is connected.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

ftPnniDTLVPI 1.3.6.1.4.1.326.2.2.2.1.9.5.1.6
This is the output path in the output port above that is the signalling path to the peer given by the next node in the DTL.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

ftPnniDTLStatus 1.3.6.1.4.1.326.2.2.2.1.9.5.1.7
The entry status of this entry in the table.
Status: deprecated Access: read-create
OBJECT-TYPE    
  EntryStatus  

ftPnniSummaryTable 1.3.6.1.4.1.326.2.2.2.1.9.6
A table of Prefixes that are used for either summarizing or suppressing internal and exterior reachability information by the FT-PNNI routing protocol
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FtPnniSummaryEntry

ftPnniSummaryEntry 1.3.6.1.4.1.326.2.2.2.1.9.6.1
An entry in the FT-PNNI Summary table.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  FtPnniSummaryEntry  

ftPnniSummaryAddress 1.3.6.1.4.1.326.2.2.2.1.9.6.1.1
The address prefix that is to be either summarized or suppressed by the FT-PNNI routing protocol
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

ftPnniSummaryPrefixLength 1.3.6.1.4.1.326.2.2.2.1.9.6.1.2
This value is the mask for the address. This gives length of the address prefix in number of bits
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

ftPnniSummaryType 1.3.6.1.4.1.326.2.2.2.1.9.6.1.3
This value identifies the type of the summary being described
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER internal(1), exterior(2)  

ftPnniSummarySuppress 1.3.6.1.4.1.326.2.2.2.1.9.6.1.4
The Suppress flag determinces what is to be done with this address. The default value (no) will indicate that the summary should be propagated. If the value is yes, this summary and any reachable address it summarizes are suppressed for being propagated
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ftPnniSummaryState 1.3.6.1.4.1.326.2.2.2.1.9.6.1.5
This value indicates whether the summary is currently being advertised by the FT-PNNI routing protocol
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER advertising(1), suppressing(2), inactive(3)  

ftPnniSummaryStatus 1.3.6.1.4.1.326.2.2.2.1.9.6.1.6
The entry status of this entry in the table.
Status: deprecated Access: read-create
OBJECT-TYPE    
  EntryStatus  

upcContractTable 1.3.6.1.4.1.326.2.2.2.1.10.1
A table of user defined UPC traffic contracts.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UpcContractEntry

upcContractEntry 1.3.6.1.4.1.326.2.2.2.1.10.1.1
A table entry containing a user defined UPC traffic contract.
Status: current Access: not-accessible
OBJECT-TYPE    
  UpcContractEntry  

upcContractKey 1.3.6.1.4.1.326.2.2.2.1.10.1.1.1
The key of this UPC configuration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..32767  

upcContractEntryStatus 1.3.6.1.4.1.326.2.2.2.1.10.1.1.2
The SNMP status of this upcContract entry.
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

upcContractPCR01 1.3.6.1.4.1.326.2.2.2.1.10.1.1.3
The peak cell rate (cells/sec) for cell loss priority 0+1
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractSCR01 1.3.6.1.4.1.326.2.2.2.1.10.1.1.4
The sustained cell rate (cells/sec) for cell loss priority 0+1
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractMBS01 1.3.6.1.4.1.326.2.2.2.1.10.1.1.5
The maximum burst size (cells) for cell loss priority 0+1
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractPCR0 1.3.6.1.4.1.326.2.2.2.1.10.1.1.6
The peak cell rate (cells/sec) for cell loss priority 0
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractSCR0 1.3.6.1.4.1.326.2.2.2.1.10.1.1.7
The sustained cell rate (cells/sec) for cell loss priority 0
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractMBS0 1.3.6.1.4.1.326.2.2.2.1.10.1.1.8
The maximum burst size (cells) for cell loss priority 0.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractCDVT 1.3.6.1.4.1.326.2.2.2.1.10.1.1.9
The Cell Delay Variation Tolerance associated with PCR's. The Default CDVT values (in microseconds) for the various physical media are: DS1_DEFAULT_LINK_CDVT - 5000 DS3_DEFAULT_LINK_CDVT - 2500 E1_DEFAULT_LINK_CDVT - 5000 E3_DEFAULT_LINK_CDVT - 2500 J2_DEFAULT_LINK_CDVT - 5000 SONET_OC3_LINK_DEFAULT_CDVT - 250 SONET_OC12_LINK_DEFAULT_CDVT - 250 SONET_OC48_LINK_DEFAULT_CDVT - 250 TAXI_DEFAULT_LINK_CDVT - 1000 TP25_DEFAULT_LINK_CDVT - 5000 CTRLPORT_DEFAULT_LINK_CDVT - 5000 BACKPLANE_DEFAULT_LINK_CDVT - 100
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractTagReq 1.3.6.1.4.1.326.2.2.2.1.10.1.1.10
Should we tag (instead of drop) non-compliant CLP=0 cells?.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractAal5Epd 1.3.6.1.4.1.326.2.2.2.1.10.1.1.11
Should we do AAL5 EPD on this connection?. This variable has been subsumed by the two new variables upcContractIsAAL5 and upcContractdoPacketDiscard. These new variables allow us to decouple the AAL5'ness of a connection from whether we are going to do packet discard on it if it is AAL5.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractName 1.3.6.1.4.1.326.2.2.2.1.10.1.1.12
The name associated with this UPC traffic contract.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..19)  

upcContractDoGCRAPolicing 1.3.6.1.4.1.326.2.2.2.1.10.1.1.13
Should we suppress GCRA policing on connections using this UPC Contract ?
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

upcContractIsAAL5 1.3.6.1.4.1.326.2.2.2.1.10.1.1.14
Is this UPC contract using AAL5?
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER true(1), false(2)  

upcContractDoPacketDiscard 1.3.6.1.4.1.326.2.2.2.1.10.1.1.15
Should we perform AAL5 Packet Discard (EPD/PPD) on this UPC contract. This variable only has meaning if the connection is also AAL5
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

upcContractDoPPPolicing 1.3.6.1.4.1.326.2.2.2.1.10.1.1.16
Should we perform AAL5 Partial Packet Policing on this UPC contract. This variable only has meaning if the connections is also AAL5.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

upcContractDoUBRTagging 1.3.6.1.4.1.326.2.2.2.1.10.1.1.17
Should we perform tagging (set CLP=1) of all cells of connections that use this UBR traffic contract?
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

upcContractSchedMode 1.3.6.1.4.1.326.2.2.2.1.10.1.1.18
This variable indicates the scheduling mode that is requested for connections that use this UPC contract.
Status: current Access: read-create
OBJECT-TYPE    
  AtmConnSchedMode  

upcContractUseAltCLPThreshold 1.3.6.1.4.1.326.2.2.2.1.10.1.1.19
This flag determines whether the Series-DW per-VC Alternate CLP Threshold should be used for all non-ABR VC's created with this UPC contract.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

upcContractMCR 1.3.6.1.4.1.326.2.2.2.1.10.1.1.20
The minimum cell rate (cells/sec) for ABR connections.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractEstimatedUbrBandwidth 1.3.6.1.4.1.326.2.2.2.1.10.1.1.21
The estimated UBR bandwidth in Kilo-CPS associated with this UPC contract
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractAAL5CountingMode 1.3.6.1.4.1.326.2.2.2.1.10.1.1.22
The Counter mode for an AAL5 connection
Status: current Access: read-create
OBJECT-TYPE    
  AAL5CountingMode  

upcContractServiceCategory 1.3.6.1.4.1.326.2.2.2.1.10.1.1.23
Index of this service category within serviceCategoryTable
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractPoliceScheme 1.3.6.1.4.1.326.2.2.2.1.10.1.1.24
It identifies the policing associated with the UPC contract as defined in the ATM Forum TM 4.0 specifications. However, the policing schemes cbr0 and cbr0tag are specific to FORE switches
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER cbr1(1), cbr0(2), cbr0tag(3), vbr1(4), vbr2(5), vbr3(6), abr1(7), ubr1(8), ubr2(9)  

upcContractPCR 1.3.6.1.4.1.326.2.2.2.1.10.1.1.25
The peak cell rate (cells/sec)
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractSCR 1.3.6.1.4.1.326.2.2.2.1.10.1.1.26
The sustained cell rate (cells/sec). It also holds the PCR0 value for cbr0 & cbr0tag contracts
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractMBS 1.3.6.1.4.1.326.2.2.2.1.10.1.1.27
The maximum burst size (cells)
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractServiceSubCategory 1.3.6.1.4.1.326.2.2.2.1.10.1.1.28
The Service subcategory for this connection.Default value is 1.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..16  

upcContractCongestionBasedPeakBw 1.3.6.1.4.1.326.2.2.2.1.10.1.1.29
The expected peak bandwidth for this congestion based UPC contract
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

upcContractBehaviorClassSelector 1.3.6.1.4.1.326.2.2.2.1.10.1.1.30
The behavior class selector (BCS) for this UPC contract
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

qosClassExpansionTable 1.3.6.1.4.1.326.2.2.2.1.17.1
A table of user defined QOS Class Expansions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QosClassExpansionEntry

qosClassExpansionEntry 1.3.6.1.4.1.326.2.2.2.1.17.1.1
A table entry containing a user defined QOS Class Expansion.
Status: current Access: not-accessible
OBJECT-TYPE    
  QosClassExpansionEntry  

qosClassExpansionKey 1.3.6.1.4.1.326.2.2.2.1.17.1.1.1
The unique key for the set of entries in this table that make up a QOS Class Mapping table. Only one entry for each Class is allowed per key.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

qosClassValue 1.3.6.1.4.1.326.2.2.2.1.17.1.1.2
QOS Class which needs to be expanded. If a class does not exist for a specific Expansion Key, all qos parameters will be interpreted as any acceptable qos parameter value.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER class0(1), class1(2), class2(3), class3(4), class4(5)  

qosClassExpansionEntryStatus 1.3.6.1.4.1.326.2.2.2.1.17.1.1.3
The SNMP status of this Expansion entry.
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

qosClassFwdCtd 1.3.6.1.4.1.326.2.2.2.1.17.1.1.4
The maximum acceptable forward Cell Transfer Delay in microseconds to be used for this expansion. A value of 16777215 will signify any acceptable forward CTD value.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..16777215  

qosClassFwdCdv 1.3.6.1.4.1.326.2.2.2.1.17.1.1.5
The maximum acceptable peak to peak forward Cell Delay Variation in micro-seconds to be used for this expansion. A value of 16777215 will signify any acceptable forward CDV value.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..16777215  

qosClassBackCdv 1.3.6.1.4.1.326.2.2.2.1.17.1.1.6
The maximum acceptable peak to peak backward Cell Delay Variation in micro-seconds to be used for this expansion. A value of 16777215 will signify any acceptable backward CDV value.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..16777215  

qosClassFwdClr 1.3.6.1.4.1.326.2.2.2.1.17.1.1.7
10 raised to the power of this value signifies the maximum acceptable forward Cell Loss Ratio value to be used for this expansion. The valid values are from 1 to 15 (both inclusive) and 255. A value of 255 will signify any acceptable forward CLR value.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..255  

qosClassBackClr 1.3.6.1.4.1.326.2.2.2.1.17.1.1.8
10 raised to the power of this value signifies the maximum acceptable backward Cell Loss Ratio value to be used for this expansion. The valid values are from 1 to 15 (both inclusive) and 255. A value of 255 will signify any acceptable backward CLR value.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..255  

qosClassName 1.3.6.1.4.1.326.2.2.2.1.17.1.1.9
A name associated with this entry in the qos class table
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..19)  

pathExtQosMetricTable 1.3.6.1.4.1.326.2.2.2.1.18.1
Qos metric table for path extension
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PathExtQosMetricEntry

pathExtQosMetricEntry 1.3.6.1.4.1.326.2.2.2.1.18.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  PathExtQosMetricEntry  

pathExtQosMetricIndex 1.3.6.1.4.1.326.2.2.2.1.18.1.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

pathExtQosMetricMaxCtd 1.3.6.1.4.1.326.2.2.2.1.18.1.1.2
cell transfer delay in microseconds
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pathExtQosMetricMaxCdv 1.3.6.1.4.1.326.2.2.2.1.18.1.1.3
cell delay variation in microseconds
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pathExtQosMetricMaxClr 1.3.6.1.4.1.326.2.2.2.1.18.1.1.4
cell loss ratio. 10**(-n) where n is the returned value
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pathExtQosMetricEntryStatus 1.3.6.1.4.1.326.2.2.2.1.18.1.1.5
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

pathExtTable 1.3.6.1.4.1.326.2.2.2.1.18.2
path extension table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PathExtEntry

pathExtEntry 1.3.6.1.4.1.326.2.2.2.1.18.2.1
A table entry containing path Qos Metric information.
Status: current Access: not-accessible
OBJECT-TYPE    
  PathExtEntry  

pathExtCbrMetric 1.3.6.1.4.1.326.2.2.2.1.18.2.1.1
index to the path ext qos metric table
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pathExtRtVbrMetric 1.3.6.1.4.1.326.2.2.2.1.18.2.1.2
index to the path ext qos metric table
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pathExtNrtVbrMetric 1.3.6.1.4.1.326.2.2.2.1.18.2.1.3
index to the path ext qos metric table
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pathExtAbrMetric 1.3.6.1.4.1.326.2.2.2.1.18.2.1.4
index to the path ext qos metric table
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pathExtUbrMetric 1.3.6.1.4.1.326.2.2.2.1.18.2.1.5
index to the path ext qos metric table
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

pathExtEntryStatus 1.3.6.1.4.1.326.2.2.2.1.18.2.1.6
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

outputPathExtTable 1.3.6.1.4.1.326.2.2.2.1.18.3
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OutputPathExtEntry

outputPathExtEntry 1.3.6.1.4.1.326.2.2.2.1.18.3.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  OutputPathExtEntry  

opathExtCbrMetric 1.3.6.1.4.1.326.2.2.2.1.18.3.1.1
index to the path ext qos metric table
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

opathExtRtVbrMetric 1.3.6.1.4.1.326.2.2.2.1.18.3.1.2
index to the path ext qos metric table
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

opathExtNrtVbrMetric 1.3.6.1.4.1.326.2.2.2.1.18.3.1.3
index to the path ext qos metric table
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

opathExtAbrMetric 1.3.6.1.4.1.326.2.2.2.1.18.3.1.4
index to the path ext qos metric table
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

opathExtUbrMetric 1.3.6.1.4.1.326.2.2.2.1.18.3.1.5
index to the path ext qos metric table
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

opathExtEntryStatus 1.3.6.1.4.1.326.2.2.2.1.18.3.1.6
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

vpGroupTable 1.3.6.1.4.1.326.2.2.2.1.18.4
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VpGroupEntry

vpGroupEntry 1.3.6.1.4.1.326.2.2.2.1.18.4.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  VpGroupEntry  

vpGroupIndex 1.3.6.1.4.1.326.2.2.2.1.18.4.1.1
Zero mean not belong to any vpgroup group
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vpGroupPort 1.3.6.1.4.1.326.2.2.2.1.18.4.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vpGroupVPI 1.3.6.1.4.1.326.2.2.2.1.18.4.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vpGroupVPCI 1.3.6.1.4.1.326.2.2.2.1.18.4.1.4
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

vpGroupEntryStatus 1.3.6.1.4.1.326.2.2.2.1.18.4.1.5
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  EntryStatus  

poolConfPPCalls 1.3.6.1.4.1.326.2.2.2.1.19.1.1
Specifies the number of point to point calls that the switch should handle through pools. The switch comes up with enough resources in the pools to handle so many point to point calls. The new value will take effect at the next reboot.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

poolConfPMPCalls 1.3.6.1.4.1.326.2.2.2.1.19.1.2
Specifies the number of point to multipoint calls that the switch should handle through pools. The switch comes up with enough resources in the pools to handle so many point to multipoint calls. The new value will take effect at the next reboot.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

poolConfMaxPercentage 1.3.6.1.4.1.326.2.2.2.1.19.1.5
Limits the max percentage of the main heap that can be taken for pool configuration purposes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

swBoardTable 1.3.6.1.4.1.326.2.2.2.1.7.1
A table of ATM switch cluster configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwBoardEntry

swBoardEntry 1.3.6.1.4.1.326.2.2.2.1.7.1.1
A table entry containing ATM switch cluster information, index by the switch board.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwBoardEntry  

swBoardIndex 1.3.6.1.4.1.326.2.2.2.1.7.1.1.1
The index of this switch board within the ATM switch cluster.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swBoardMaxPaths 1.3.6.1.4.1.326.2.2.2.1.7.1.1.2
The maximum number of input VPIs (Virtual Path Identifier) on this switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swBoardMaxChannels 1.3.6.1.4.1.326.2.2.2.1.7.1.1.3
The maximum number of input VCIs (Virtual Channel Identifiers) on this switch board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swBoardAtmAddress 1.3.6.1.4.1.326.2.2.2.1.7.1.1.4
The address of this ATM switch board.
Status: current Access: read-only
OBJECT-TYPE    
  SpansAddress  

swBoardUptime 1.3.6.1.4.1.326.2.2.2.1.7.1.1.5
The length of time this ATM switch board has been up, in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

swBoardCDV 1.3.6.1.4.1.326.2.2.2.1.7.1.1.6
The switch board Cell Delay Variation (CDV) specified in microseconds, indicates the time window in which a cell may be received on a connection and be accepted. A cell that is received on a connection outside the CDV window will be tagged or dropped as indicated by the swBoardPolicingAction object. The boardCDV is the default CDV for all the connection on this switch board. Individual connections can be set to explicitly override this value.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

swBoardPolicingAction 1.3.6.1.4.1.326.2.2.2.1.7.1.1.7
This object indicates the action the switch board will take in case of bandwidth violation. The swBoardPolicingAction is the default policing action for all the connections on this switch board. Individual connections can be set to explicitly override this default action.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER tag(1), drop(2)  

swBoardNsapPrefix 1.3.6.1.4.1.326.2.2.2.1.7.1.1.8
The default NSAP (Network Service Access Point) prefix for this ATM switch board. The NSAP prefix will be used in the ILMI address registration message as well as the 'hello-indication' SPANS-NNI message.
Status: current Access: read-write
OBJECT-TYPE    
  NsapPrefix  

swBoardClockScalingFactor 1.3.6.1.4.1.326.2.2.2.1.7.1.1.9
This specifies the value written into the switch boards Time Scaling Factor register. See Sec. 3.2.1 for more info. The Time Scaling Factor is an 8-bit register that determines the number of 25ns clock cycles that occur between increments of the Time and Interrupt Timer Reigsters. Increasing the Time Scale Factor increases the burst tolerance that can be represented by the policer (in multiples of .838 seconds) while reducing the precision of the policer by a similar factor. The possible values for this variable are 1 through 255.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

swBoardDebugMode 1.3.6.1.4.1.326.2.2.2.1.7.1.1.10
This object indicates whether or not debugging services are available for this switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(1), on(2)  

swBoardMulticastMode 1.3.6.1.4.1.326.2.2.2.1.7.1.1.11
This object identifies the mode in which this ATM switch board is operating. Extended-mode provides greater flexibility when selecting VCI for point to multipoint connections. Non-extended (mixed) mode is more restrictive. If any series A or B netmods are present, the switch board should operate in non-extended mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER non-extended(1), extended(2)  

swBoardFingerMode 1.3.6.1.4.1.326.2.2.2.1.7.1.1.12
This object indicates whether or not finger services are available for this switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

swBoardATMLayerOAM 1.3.6.1.4.1.326.2.2.2.1.7.1.1.13
This object specifies whether the processing of ATM layer OAM cells by this switch board is enabled or disabled.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swBoardTopoTable 1.3.6.1.4.1.326.2.2.2.1.8.1
A table of switch board topology general information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwBoardTopoEntry

swBoardTopoEntry 1.3.6.1.4.1.326.2.2.2.1.8.1.1
A table entry containing switch board topology information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwBoardTopoEntry  

swBoardTopoIndex 1.3.6.1.4.1.326.2.2.2.1.8.1.1.1
The index of this switch board within the ATM switch cluster. This object should be the same as the swBoardIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  


swBoardLinkTable 1.3.6.1.4.1.326.2.2.2.1.8.2
A table of ATM links that are known to a given switch board in the switch cluster. If all boards in the switch cluster are interconnected, all swBoardLinkEntries will be identical.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwBoardLinkEntry

swBoardLinkEntry 1.3.6.1.4.1.326.2.2.2.1.8.2.1
A table entry containing link information known to a given switch board.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwBoardLinkEntry  

swBoardLinkIndex 1.3.6.1.4.1.326.2.2.2.1.8.2.1.1
The index of this switch board within the ATM switch cluster. This object should be the same as the swBoardIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swBoardLinkSrc 1.3.6.1.4.1.326.2.2.2.1.8.2.1.2
The ATM address of the source switch of this link.
Status: current Access: read-only
OBJECT-TYPE    
  SpansAddress  

swBoardLinkDest 1.3.6.1.4.1.326.2.2.2.1.8.2.1.3
The ATM address of the destination switch of this link.
Status: current Access: read-only
OBJECT-TYPE    
  SpansAddress  

swBoardLinkCapacity 1.3.6.1.4.1.326.2.2.2.1.8.2.1.4
The free capacity of this link in kilobits per second.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swBoardLinkAge 1.3.6.1.4.1.326.2.2.2.1.8.2.1.5
The freshness of the information about this link. The actual value has no units associated with it. It should be used for comparison.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

oamGeneratingChannelTable 1.3.6.1.4.1.326.2.2.2.1.12.1
When an AIS cell is generated on a particular channel it gets added to this table. If a channel is deleted the corresponding entry is removed from this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OamGeneratingChannelEntry

oamGeneratingChannelEntry 1.3.6.1.4.1.326.2.2.2.1.12.1.1
A table entry containing a channel which has generated AIS cells.
Status: current Access: not-accessible
OBJECT-TYPE    
  OamGeneratingChannelEntry  

oamGeneratingChannelCells 1.3.6.1.4.1.326.2.2.2.1.12.1.1.1
The number of AIS OAM cells generated on this channel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

oamGeneratingOpathTable 1.3.6.1.4.1.326.2.2.2.1.12.2
When an RDI cell is generated on a particular outgoing path it gets added to this table. If an outgoing path is deleted the corresponding entry is removed from this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OamGeneratingOpathEntry

oamGeneratingOpathEntry 1.3.6.1.4.1.326.2.2.2.1.12.2.1
A table entry containing an outgoing path which has generated RDI cells.
Status: current Access: not-accessible
OBJECT-TYPE    
  OamGeneratingOpathEntry  

oamGeneratingOpathCells 1.3.6.1.4.1.326.2.2.2.1.12.2.1.1
The number of RDI OAM cells generated on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

oamGeneratingPathrTable 1.3.6.1.4.1.326.2.2.2.1.12.3
When an AIS cell is generated on a particular through path it gets added to this table. If a through path is deleted the corresponding entry is removed from this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OamGeneratingPathrEntry

oamGeneratingPathrEntry 1.3.6.1.4.1.326.2.2.2.1.12.3.1
A table entry containing a through path which has generated AIS cells.
Status: current Access: not-accessible
OBJECT-TYPE    
  OamGeneratingPathrEntry  

oamGeneratingPathrCells 1.3.6.1.4.1.326.2.2.2.1.12.3.1.1
The number of AIS OAM cells generated on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

oamReceivedPathTable 1.3.6.1.4.1.326.2.2.2.1.12.4
When an OAM cell is received on a particular terminating path it gets added to this table. If a terminating path is deleted the corresponding entry is removed from this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OamReceivedPathEntry

oamReceivedPathEntry 1.3.6.1.4.1.326.2.2.2.1.12.4.1
A table entry containing a terminating path which has received OAM cells.
Status: current Access: not-accessible
OBJECT-TYPE    
  OamReceivedPathEntry  

oamReceivedPathAISCells 1.3.6.1.4.1.326.2.2.2.1.12.4.1.1
The number of AIS OAM cells received on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

oamReceivedPathRDICells 1.3.6.1.4.1.326.2.2.2.1.12.4.1.2
The number of RDI OAM cells received on this path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

guardTable 1.3.6.1.4.1.326.2.2.2.1.13.1
The OAM guards for each board in a switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GuardEntry

guardEntry 1.3.6.1.4.1.326.2.2.2.1.13.1.1
A table entry containing the guards for a board.
Status: current Access: not-accessible
OBJECT-TYPE    
  GuardEntry  

oamGuard 1.3.6.1.4.1.326.2.2.2.1.13.1.1.1
The value of sysUpTime the last time an OAM cell was generated/received on this board.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

trapNumberOfDest 1.3.6.1.4.1.326.2.2.2.2.1.1
The current number of configured trap destinations. All traps are sent to all destinations.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

trapDestTable 1.3.6.1.4.1.326.2.2.2.2.1.2
A table of destinations to which the agent sends traps.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TrapDestEntry

trapDestEntry 1.3.6.1.4.1.326.2.2.2.2.1.2.1
A table entry containing address of a management station, to which the agent sends traps.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  TrapDestEntry  

trapDest 1.3.6.1.4.1.326.2.2.2.2.1.2.1.1
Address to which the agent sends traps. Usually a network management station sets this address to itself.
Status: deprecated Access: read-only
OBJECT-TYPE    
  IpAddress  

trapDestStatus 1.3.6.1.4.1.326.2.2.2.2.1.2.1.2
The status of this trap destination entry.
Status: deprecated Access: read-create
OBJECT-TYPE    
  EntryStatus  

snmpReconfigure 1.3.6.1.4.1.326.2.2.2.2.2.1
The SNMP agent will reset itself and reconfigure its database from the default database when this variable is set to enable(2). After reconfiguring is done, the value of this object is disable(1). Note that enabling snmpReconfigure will end up with a loss of the entire ATM configuration.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

snmpReadCommunity 1.3.6.1.4.1.326.2.2.2.2.2.2
The community string used for SNMP (v1) read operations, i.e. get and getnext requests. This has been deprecated, since it's now possible to have more than one read community string. Setting this variable will result in all current read community strings being deleted, and this one added. Note this object is write-only and reading it will result in implementation-specific results.
Status: deprecated Access: read-write
OBJECT-TYPE    
  OCTET STRING  

snmpWriteCommunity 1.3.6.1.4.1.326.2.2.2.2.2.3
The community string used for SNMP (v1) write operations, i.e. set requests. This has been deprecated, since it's now possible to have more than one write community string. Setting this variable will result in all current write community strings being deleted, and this one added. Note this object is write-only and reading it will result in implementation-specific results.
Status: deprecated Access: read-write
OBJECT-TYPE    
  OCTET STRING  

snmpWarmStart 1.3.6.1.4.1.326.2.2.2.2.2.4
The SNMP agent will reset the switch, and restart the switch control software using the existing configuration database when this variable is set to enable(2). After the warm start, the value of this object is disable(1). A warmStart trap is sent after the switch control software restarts.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

snmpColdStart 1.3.6.1.4.1.326.2.2.2.2.2.5
The SNMP agent will reset the configuration database for all ATM related configuration objects, and reboot the switch, when this variable is set to enableResetAtmConf(2). When the value of this variable is set to enableResetAllConf(3), all configuration objects, including ATM and IP objects will be removed, and the switch will be rebooted. A coldStart trap is sent just before the trap destination table is removed. After the cold start, the value of this object is disable(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enableResetATMconf(2), enableResetAllConf(3)  

snmpRemoteSetsStatus 1.3.6.1.4.1.326.2.2.2.2.2.6
The value of this object controls SNMP set operations from remote management stations. The default value is enabled(1). If it is set to disabled(2), set requests from remote management stations will not be processed and an authorization error is returned. This value can be set only by the manager running on this device.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

snmpThisAgentBoardNumber 1.3.6.1.4.1.326.2.2.2.2.5.1
The instance of this agent type within the enclosure; typically a board number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

snmpAgentTable 1.3.6.1.4.1.326.2.2.2.2.5.2
A table of SNMP agent IP addresses. Each entry in this table represents an IP address which may be used to reach the associated SNMP agent, assuming appropriate network connectivity.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnmpAgentEntry

snmpAgentEntry 1.3.6.1.4.1.326.2.2.2.2.5.2.1
A table entry containing the identity and address of an SNMP agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAgentEntry  

snmpAgentBoardNumber 1.3.6.1.4.1.326.2.2.2.2.5.2.1.1
The number of the SNMP agent within this enclosure. This generally corresponds to a board number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

snmpAgentInterface 1.3.6.1.4.1.326.2.2.2.2.5.2.1.2
An interface number associated with the agent IP address. This number is for tabulation purposes only, and has no other significance.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

snmpAgentAddress 1.3.6.1.4.1.326.2.2.2.2.5.2.1.3
The IP address of the identified SNMP agent.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

asxSwLinkDown 1.3.6.1.4.1.326.2.2.0.0
An asxSwLinkDown trap signifies that the sending protocol entity recognizes a failure in one of the ATM Switch links that is connected to another switch.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSwLinkUp 1.3.6.1.4.1.326.2.2.0.1
An asxSwLinkUp trap signifies that the sending protocol entity recognizes that one of the ATM Switch links that is connected to another switch has come up.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxHostLinkDown 1.3.6.1.4.1.326.2.2.0.2
An asxHostLinkDown trap signifies that the sending protocol entity recognizes a failure in one of the ATM Switch links that is connected to a host.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxHostLinkUp 1.3.6.1.4.1.326.2.2.0.3
An asxHostLinkUp trap signifies that the sending protocol entity recognizes that one of the ATM Switch links that is connected to a host has come up.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxNetModuleDown 1.3.6.1.4.1.326.2.2.0.4
An asxNetModuleDown trap signifies that the sending protocol entity recognizes a failure in one of the ATM Switch network modules, that is identified by the board and the module numbers. This is probably caused by a hot-swap of a network module.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxNetModuleUp 1.3.6.1.4.1.326.2.2.0.5
An asxNetModuleUp trap signifies that the sending protocol entity recognizes a new operational ATM Switch network module, that is identified by the board and the module numbers. This is probably caused by a hot-swap of a network module.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxPsInputDown 1.3.6.1.4.1.326.2.2.0.6
This trap alerts that one ATM switch power supply failed due to failure in the input voltage. The power supply that failed is identified by the power supply index. Note that an input voltage may be out of spec and may not cause a power supply failure if high loads are not applied.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxPsInputUp 1.3.6.1.4.1.326.2.2.0.7
This trap alerts that one ATM switch power supply that had an input failure is up. The power supply that is back up is identified by the power supply index.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxPsOutputDown 1.3.6.1.4.1.326.2.2.0.9
This trap alerts that one ATM switch power supply output failed, or the power supply was physically removed. The power supply that failed is identified by the power supply index.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxPsOutputUp 1.3.6.1.4.1.326.2.2.0.10
This trap alerts that one ATM switch power supply that had an output failure or was removed is now up. The power supply that is back up is identified by the power supply index.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxFanBankDown 1.3.6.1.4.1.326.2.2.0.22
This trap alerts that one ATM switch fan bank failed. The fan bank that failed is identified by the fan bank index.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxFanBankUp 1.3.6.1.4.1.326.2.2.0.23
This trap alerts that one ATM switch fan bank is up. The fan bank that is back up is identified by the fan bank index.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxLinkDown 1.3.6.1.4.1.326.2.2.0.28
This trap alerts that the link that is identified by portName was configured up, but its underlying physical layer has lost its carrier (or the framing bit) and is currently down.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxLinkUp 1.3.6.1.4.1.326.2.2.0.29
This trap alerts that the link that is identified by portName is back up.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSpansDown 1.3.6.1.4.1.326.2.2.0.30
This trap alerts that the SPANS signalling on the link that is identified by the sigPathPort and sigPathVPI failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSpansUp 1.3.6.1.4.1.326.2.2.0.31
This trap alerts that the SPANS signalling on the link that is identified by the sigPathPort and sigPathVPI is up.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxTempSensorOverTemp 1.3.6.1.4.1.326.2.2.0.32
This trap alerts that one of the temperature sensors indicates over temperature. The temperature sensor is identified by the temperature sensor index.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxTempSensorRegularTemp 1.3.6.1.4.1.326.2.2.0.33
This trap alerts that one of the temperature sensors indicates regular temperature. The temperature sensor is identified by the temperature sensor index.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxFabricTemperatureOverTemp 1.3.6.1.4.1.326.2.2.0.34
This trap alerts that one of the temperature sensors indicates over temperature. The temperature sensor is identified by the temperature sensor index.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxFabricTemperatureRegularTemp 1.3.6.1.4.1.326.2.2.0.35
This trap alerts that one of the temperature sensors indicates regular temperature. The temperature sensor is identified by the temperature sensor index.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetLOSDetected 1.3.6.1.4.1.326.2.2.0.36
This trap indicates that the specified SONET port is experiencing Loss Of Signal. Bellcore Document TA-NWT-000253 Section 6.3.1.1.1 states that... A SONET NE shall declare a LOS failure when the LOS defect persists for 2.5 (+- .5) seconds, or when a LOS defect is present and the criteria for LOF failure declaration have been met.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetLOSCleared 1.3.6.1.4.1.326.2.2.0.37
This trap indicates that the LOS condition identified by trap asxSonetLOSDetected has been cleared.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetPathLabelDetected 1.3.6.1.4.1.326.2.2.0.38
This trap indicates that the specified SONET port is receiving and errored C2 Path Label byte. Reference Bellcore Document TA-NWT-000253 Section 3.3.2.3 and 6.3.1.1.8 the Path Label (C2) byte should have the value 0x13 or 0x01.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetPathLabelCleared 1.3.6.1.4.1.326.2.2.0.39
This trap indicates that the Errored Path Label (C2) byte error condition signaled by the asxSonetPathLabelDetected trap has been cleared.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetLineAISDetected 1.3.6.1.4.1.326.2.2.0.40
This trap indicates that the specified SONET port is receiving a Line level Alarm Indication Signal from the far-end equipment.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetLineAISCleared 1.3.6.1.4.1.326.2.2.0.41
This trap indicates that the Line AIS error condition signaled by the asxSonetLineAISDetected trap has been cleared.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3PLCPYellowDetected 1.3.6.1.4.1.326.2.2.0.46
This trap indicates that the specified DS3 port has detected incoming PLCP Yellow Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3PLCPYellowCleared 1.3.6.1.4.1.326.2.2.0.47
This trap indicates that the specified DS3 port has detected clearance of incoming PLCP Yellow Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3PLCPLOFDetected 1.3.6.1.4.1.326.2.2.0.48
This trap indicates that the specified DS3 port has detected incoming PLCP LOF Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3PLCPLOFCleared 1.3.6.1.4.1.326.2.2.0.49
This trap indicates that the specified DS3 port has detected clearance of incoming PLCP LOF Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3LOFDetected 1.3.6.1.4.1.326.2.2.0.50
This trap indicates that Loss Of Frame(LOF) is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3LOFCleared 1.3.6.1.4.1.326.2.2.0.51
This trap indicates that Loss Of Frame is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3AISDetected 1.3.6.1.4.1.326.2.2.0.52
This trap indicates that AIS Alarm is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3AISCleared 1.3.6.1.4.1.326.2.2.0.53
This trap indicates that AIS Alarm is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1PLCPYellowDetected 1.3.6.1.4.1.326.2.2.0.60
This trap indicates that the specified DS1 port has detected incoming PLCP Yellow Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1PLCPYellowCleared 1.3.6.1.4.1.326.2.2.0.61
This trap indicates that the specified DS1 port has detected clearance of incoming PLCP Yellow Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1PLCPLOFDetected 1.3.6.1.4.1.326.2.2.0.62
This trap indicates that the specified DS1 port has detected incoming PLCP LOF Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1PLCPLOFCleared 1.3.6.1.4.1.326.2.2.0.63
This trap indicates that the specified DS1 port has detected clearance of incoming PLCP LOF Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1YellowDetected 1.3.6.1.4.1.326.2.2.0.64
This trap indicates that Yellow Alarm is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1YellowCleared 1.3.6.1.4.1.326.2.2.0.65
This trap indicates that Yellow Alarm is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1AISDetected 1.3.6.1.4.1.326.2.2.0.66
This trap indicates that AIS Alarm is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1AISCleared 1.3.6.1.4.1.326.2.2.0.67
This trap indicates that AIS Alarm is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1LOSDetected 1.3.6.1.4.1.326.2.2.0.68
This trap indicates that LOS Alarm is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1LOSCleared 1.3.6.1.4.1.326.2.2.0.69
This trap indicates that LOS Alarm is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1LOFDetected 1.3.6.1.4.1.326.2.2.0.70
This trap indicates that LOF Alarm is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1LOFCleared 1.3.6.1.4.1.326.2.2.0.71
This trap indicates that LOF Alarm is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3FERFDetected 1.3.6.1.4.1.326.2.2.0.74
This trap indicates that FERF Alarm or DS3 Yellow Alarm is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3FERFCleared 1.3.6.1.4.1.326.2.2.0.75
This trap indicates that FERF Alarm or DS3 Yellow Alarm is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3YellowDetected 1.3.6.1.4.1.326.2.2.0.78
This trap indicates that the Yellow Alarm is being detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3YellowCleared 1.3.6.1.4.1.326.2.2.0.79
This trap indicates that Yellow alarm has cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3OOFDetected 1.3.6.1.4.1.326.2.2.0.80
This trap indicates that Out Of Frame (OOF) is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3OOFCleared 1.3.6.1.4.1.326.2.2.0.81
This trap indicates that Loss Of Frame is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3AtmLCDDetected 1.3.6.1.4.1.326.2.2.0.82
This trap indicates that the specified E3 port is experiencing Loss of Cell Deliniation (LCD). A LCD failure is declared when the LCD defect persists for a period of 2.5 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3AtmLCDCleared 1.3.6.1.4.1.326.2.2.0.83
This trap indicates that the LCD failure identified by trap asxE3AtmLCDDetected has been cleared. A LCD failure is cleared when the LCD defect is absent for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3PLCPYellowDetected 1.3.6.1.4.1.326.2.2.0.86
This trap indicates that the specified E3 port has detected incoming PLCP Yellow Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3PLCPYellowCleared 1.3.6.1.4.1.326.2.2.0.87
This trap indicates that the specified E3 port has detected clearance of incoming PLCP Yellow Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE1YellowDetected 1.3.6.1.4.1.326.2.2.0.90
This trap indicates that the Yellow Alarm is being detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE1YellowCleared 1.3.6.1.4.1.326.2.2.0.91
This trap indicates that Yellow alarm has cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE1LOFDetected 1.3.6.1.4.1.326.2.2.0.92
This trap indicates that LOF is being detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE1LOFCleared 1.3.6.1.4.1.326.2.2.0.93
This trap indicates that LOF is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE1PLCPYellowDetected 1.3.6.1.4.1.326.2.2.0.96
This trap indicates that the specified E1 port has detected incoming PLCP Yellow Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE1PLCPYellowCleared 1.3.6.1.4.1.326.2.2.0.97
This trap indicates that the specified E1 port has detected clearance of incoming PLCP Yellow Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE1PLCPLOFDetected 1.3.6.1.4.1.326.2.2.0.98
This trap indicates that the specified E1 port has detected incoming PLCP LOF Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE1PLCPLOFCleared 1.3.6.1.4.1.326.2.2.0.99
This trap indicates that incoming PLCP LOF alarm has been cleared on the specified E1 port.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE1LOSDetected 1.3.6.1.4.1.326.2.2.0.100
This trap indicates that the specified E1 port has detected incoming LOS Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE1LOSCleared 1.3.6.1.4.1.326.2.2.0.101
This trap indicates that incoming LOS alarm has been cleared on the specified E1 port.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE1AISDetected 1.3.6.1.4.1.326.2.2.0.102
This trap indicates that the specified E1 port has detected incoming AIS Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE1AISCleared 1.3.6.1.4.1.326.2.2.0.103
This trap indicates that incoming AIS alarm has been cleared on the specified E1 port.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3AISDetected 1.3.6.1.4.1.326.2.2.0.104
This trap indicates that the specified E3 port has detected incoming AIS Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3AISCleared 1.3.6.1.4.1.326.2.2.0.105
This trap indicates that incoming AIS alarm has been cleared on the specified E3 port.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3LOSDetected 1.3.6.1.4.1.326.2.2.0.106
This trap indicates that the specified E3 port has detected incoming LOS Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3LOSCleared 1.3.6.1.4.1.326.2.2.0.107
This trap indicates that incoming LOS alarm has been cleared on the specified E3 port.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3PLCPLOFDetected 1.3.6.1.4.1.326.2.2.0.108
This trap indicates that the specified E3 port has detected incoming PLCP LOF Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3PLCPLOFCleared 1.3.6.1.4.1.326.2.2.0.109
This trap indicates that incoming PLCP LOF alarm has been cleared on the specified E3 port.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2YellowDetected 1.3.6.1.4.1.326.2.2.0.112
This trap indicates that Yellow Alarm is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2YellowCleared 1.3.6.1.4.1.326.2.2.0.113
This trap indicates that Yellow Alarm is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2AISDetected 1.3.6.1.4.1.326.2.2.0.114
This trap indicates that AIS Alarm is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2AISCleared 1.3.6.1.4.1.326.2.2.0.115
This trap indicates that AIS Alarm is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2LOSDetected 1.3.6.1.4.1.326.2.2.0.116
This trap indicates that LOS Alarm is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2LOSCleared 1.3.6.1.4.1.326.2.2.0.117
This trap indicates that LOS Alarm is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2LOFDetected 1.3.6.1.4.1.326.2.2.0.118
This trap indicates that LOF Alarm is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2LOFCleared 1.3.6.1.4.1.326.2.2.0.119
This trap indicates that LOF Alarm is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3LOSDetected 1.3.6.1.4.1.326.2.2.0.120
This trap indicates that the specified DS3 port has detected incoming LOS Alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3LOSCleared 1.3.6.1.4.1.326.2.2.0.121
This trap indicates that the incoming LOS Alarm has been cleared on the specified DS3 port.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetLOFDetected 1.3.6.1.4.1.326.2.2.0.130
This trap indicates that the specified SONET port is experiencing Loss Of Frame (LOF) failure. An LOF failure is declared when the LOF defect persists fore a period of 2.5 +/- 0.5 seconds, except when an LOS defect or failure is present.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetLOFCleared 1.3.6.1.4.1.326.2.2.0.131
This trap indicates that the LOF failure identified by trap asxSonetLOFDetected has been cleared. The LOF failure is cleared when the LOS failure is declared, or when the LOF defect is absent for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetLineRDIDetected 1.3.6.1.4.1.326.2.2.0.132
This trap indicates that the specified SONET port is experiencing Line Remote Defect Indication (LRDI). A Line RDI failure is declared when the incoming Line RDI defects lasts for 2.5 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetLineRDICleared 1.3.6.1.4.1.326.2.2.0.133
This trap indicates that the Line RDI failure identified by trap asxSonetLineRDIDetected has been cleared. The Line RDI failure is cleared when no Line RDI defects are detected for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetPathAISDetected 1.3.6.1.4.1.326.2.2.0.134
This trap indicates that the specified SONET port is experiencing Path Alarm Inidication Signal (PAIS). A Path AIS failure is declared when the Path AIS defect persists for 2.5 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetPathAISCleared 1.3.6.1.4.1.326.2.2.0.135
This trap indicates that the PathAIS failure identified by trap asxSonetPathAISDetected has been cleared. A PAIS failure is cleared when the PAIS defect is absent for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetPathLOPDetected 1.3.6.1.4.1.326.2.2.0.136
This trap indicates that the specified SONET port is experiencing Loss Of Pointer (LOP). A LOP failure is declared when the LOP defect persists for a period of 2.5 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetPathLOPCleared 1.3.6.1.4.1.326.2.2.0.137
This trap indicates that the LOP failure identified by trap asxSonetLOPDetected has been cleared. A LOP failure is cleared when the LOP defect is absent for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetPathUNEQDetected 1.3.6.1.4.1.326.2.2.0.138
This trap indicates that the specified SONET port is experiencing unequiped (UNEQ). A UNEQ failure is declared when the UNEQ defect persists for a period of 2.5 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetPathUNEQCleared 1.3.6.1.4.1.326.2.2.0.139
This trap indicates that the UNEQ failure identified by trap asxSonetUNEQDetected has been cleared. A UNEQ failure is cleared when the UNEQ defect is absent for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetPathRDIDetected 1.3.6.1.4.1.326.2.2.0.140
This trap indicates that the specified SONET port is experiencing Path Remote Defect Indication (PRDI). A Path RDI failure is declared when the incoming Path RDI defects lasts for 2.5 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetPathRDICleared 1.3.6.1.4.1.326.2.2.0.141
This trap indicates that the Path RDI failure identified by trap asxSonetPathRDIDetected has been cleared. The Path RDI failure is cleared when no Path RDI defects are detected for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetAtmLCDDetected 1.3.6.1.4.1.326.2.2.0.142
This trap indicates that the specified SONET port is experiencing Loss of Cell Deliniation (LCD). A LCD failure is declared when the LCD defect persists for a period of 2.5 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetAtmLCDCleared 1.3.6.1.4.1.326.2.2.0.143
This trap indicates that the LCD failure identified by trap asxSonetAtmLCDDetected has been cleared. A LCD failure is cleared when the LCD defect is absent for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetAtmLineBIPDetected 1.3.6.1.4.1.326.2.2.0.144
This trap indicates that the specified SONET port is experiencing Bit Interleaved Parity (BIP) errors. A Line BIP failure is declared when the Line BIP defect persists for a period of 2.5 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSonetAtmLineBIPCleared 1.3.6.1.4.1.326.2.2.0.145
This trap indicates that the Line BIP failure identified by trap asxSonetAtmLineBIPDetected has been cleared. A Line BIP failure is cleared when the Line BIP defect is absent for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3IdleDetected 1.3.6.1.4.1.326.2.2.0.160
This trap indicates that an Idle Maintenance Signal (IDLE) is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3IdleCleared 1.3.6.1.4.1.326.2.2.0.161
This trap indicates that an Idle Maintenance Signal (IDLE) is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3AtmLCDDetected 1.3.6.1.4.1.326.2.2.0.162
This trap indicates that the specified DS3 port is experiencing Loss of Cell Deliniation (LCD). A LCD failure is declared when the LCD defect persists for a period of 2.5 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3AtmLCDCleared 1.3.6.1.4.1.326.2.2.0.163
This trap indicates that the LCD failure identified by trap asxDS3AtmLCDDetected has been cleared. A LCD failure is cleared when the LCD defect is absent for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3PbitPerrDetected 1.3.6.1.4.1.326.2.2.0.164
This trap indicates that the specified DS3 port is experiencing P-bit Parity errors. A P-bit Parity Error failure is declared when the P-bit Parity Error persists for a period of 2.5 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS3PbitPerrCleared 1.3.6.1.4.1.326.2.2.0.165
This trap indicates that the P-bit Parity Error failure identified by trap asxDS3PbitPerrDetected has been cleared. A P-bit Parity Error failure is cleared when the P-bit Parity Error defect is absent for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1PRBSDetected 1.3.6.1.4.1.326.2.2.0.176
This trap indicates that PRBS pattern is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1PRBSCleared 1.3.6.1.4.1.326.2.2.0.177
This trap indicates that PRBS pattern is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1AtmLCDDetected 1.3.6.1.4.1.326.2.2.0.178
This trap indicates that the specified DS1 port is experiencing Loss of Cell Deliniation (LCD). A LCD failure is declared when the LCD defect persists for a period of 2.5 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1AtmLCDCleared 1.3.6.1.4.1.326.2.2.0.179
This trap indicates that the LCD failure identified by trap asxDS1AtmLCDDetected has been cleared. A LCD failure is cleared when the LCD defect is absent for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1CRCErrDetected 1.3.6.1.4.1.326.2.2.0.180
This trap indicates that the specified DS1 port is experiencing excessive CRC-6 errors. A CRC-6 Error failure is declared when the CRC-6 Error persists for a period of 2.5 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDS1CRCErrCleared 1.3.6.1.4.1.326.2.2.0.181
This trap indicates that the excessive CRC-6 Error failure identified by trap asxDS1CRCErrDetected has been cleared. A CRC-6 Parity Error failure is cleared when the CRC-6 Error defect is absent for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE3TrailChangeDetected 1.3.6.1.4.1.326.2.2.0.192
This trap indicates that a change in the trail trace message was detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE1AtmLCDDetected 1.3.6.1.4.1.326.2.2.0.208
This trap indicates that the specified E1 port is experiencing Loss of Cell Deliniation (LCD). A LCD failure is declared when the LCD defect persists for a period of 2.5 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxE1AtmLCDCleared 1.3.6.1.4.1.326.2.2.0.209
This trap indicates that the LCD failure identified by trap asxE1AtmLCDDetected has been cleared. A LCD failure is cleared when the LCD defect is absent for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2RLOCDetected 1.3.6.1.4.1.326.2.2.0.224
This trap indicates that Receive Loss of Clock (RLOC) is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2RLOCCleared 1.3.6.1.4.1.326.2.2.0.225
This trap indicates that Receive Loss of Clock (RLOC) is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2HBERDetected 1.3.6.1.4.1.326.2.2.0.226
This trap indicates that High Bit Error Rate (HBER) is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2HBERCleared 1.3.6.1.4.1.326.2.2.0.227
This trap indicates that High Bit Error Rate (HBER) is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2PAISDetected 1.3.6.1.4.1.326.2.2.0.228
This trap indicates that Payload Alarm Indication Signal (PAIS) is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2PAISCleared 1.3.6.1.4.1.326.2.2.0.229
This trap indicates that Payload Alarm Indication SIgnal (PAIS) is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2AtmLCDDetected 1.3.6.1.4.1.326.2.2.0.230
This trap indicates that the specified J2 port is experiencing Loss of Cell Deliniation (LCD). A LCD failure is declared when the LCD defect persists for a period of 2.5 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2AtmLCDCleared 1.3.6.1.4.1.326.2.2.0.231
This trap indicates that the LCD failure identified by trap asxJ2AtmLCDDetected has been cleared. A LCD failure is cleared when the LCD defect is absent for 10 +/- 0.5 seconds.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2TLOCDetected 1.3.6.1.4.1.326.2.2.0.232
This trap indicates that Transmit Loss of Clock (TLOC) is detected.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxJ2TLOCCleared 1.3.6.1.4.1.326.2.2.0.233
This trap indicates that Transmit Loss of Clock (TLOC) is cleared.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxTP25LOSDetected 1.3.6.1.4.1.326.2.2.0.250
This trap indicates that LOS Alarm is detected on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxTP25LOSCleared 1.3.6.1.4.1.326.2.2.0.251
This trap indicates that LOS Alarm is cleared on the incoming signal.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxOutputQueueCongested 1.3.6.1.4.1.326.2.2.0.1024
This trap indicates that the output queue for the given priority has exceeded its dedicated length, and has begun overflowing into the shared buffer space on the netmod.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxOutputQueueCellLoss 1.3.6.1.4.1.326.2.2.0.1025
This trap indicates that the output queue for the given priority has overflowed and cells have been dropped.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxExtendedModeViolation 1.3.6.1.4.1.326.2.2.0.1026
This trap indicates that a series A or B network module was inserted into a switch board running in extended mode. Multicast will not work on the series B module without removing all series D modules and rebooting the rebooted.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxNonextendedModeWarning 1.3.6.1.4.1.326.2.2.0.1027
This trap indicates that a series C or greater network module was inserted into a switch board running in non-extended mode.
Status: current Access: read-only
NOTIFICATION-TYPE    

crConfMemoryOflow 1.3.6.1.4.1.326.2.2.0.1029
This trap is generated when the allocated callrecord memory(as indicated by crMemoryAllocated) is exceeded.
Status: current Access: read-only
NOTIFICATION-TYPE    

crXfrPrimaryXfrFailed 1.3.6.1.4.1.326.2.2.0.1030
This trap is generated when the call record transfer to the primary host(as indicated by crXfrPrimaryUrl) fails.
Status: current Access: read-only
NOTIFICATION-TYPE    

crXfrSecondaryXfrFailed 1.3.6.1.4.1.326.2.2.0.1031
This trap is generated when the call record transfer to the secondary host(as indicated by crXfrSecondaryUrl) fails.
Status: current Access: read-only
NOTIFICATION-TYPE    

crConfMemAllocFail 1.3.6.1.4.1.326.2.2.0.1032
This trap is generated when Callrecord functionality is unable to allocate memory as specified by crMemoryAllocated. This can happen when the crConfAdminStatus changes state from `off' or when the switch reboots when Callrecords is configured `on'.
Status: current Access: read-only
NOTIFICATION-TYPE    

crGeneralFailure 1.3.6.1.4.1.326.2.2.0.1033
This trap is generated when any of the callrecord related functionality fails for any reason. One example would be when the Callrecord Module fails to schedule an interval timer.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDualScpSyncFailure 1.3.6.1.4.1.326.2.2.0.1034
This trap indicates that automatic CDB synchronization is disabled due to failures.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDualScpSwitchOver 1.3.6.1.4.1.326.2.2.0.1035
This trap indicates that the backup SCP has taken control of the switch.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDualScpHotSwap 1.3.6.1.4.1.326.2.2.0.1036
This trap indicates that an SCP hotswap insertion or removal has occurred.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxVPAISDetected 1.3.6.1.4.1.326.2.2.0.1037
This trap indicates that the Alarm Indication Signal (AIS) is detected on the incoming (terminating) virtual path. This trap is generated once when the virtual path is declared to be in the active AIS state.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxVPAISCleared 1.3.6.1.4.1.326.2.2.0.1038
This trap indicates that the Alarm Indication Signal (AIS) has been removed from the incoming (terminating) virtual path. This trap is generated once when the virtual path is declared to be in the inactive AIS state.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxVPRDIDetected 1.3.6.1.4.1.326.2.2.0.1039
This trap indicates that the Remote Defect Indication (RDI) is detected on the incoming (terminating) virtual path. This trap is generated once when the virtual path is declared to be in the active RDI state.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxVPRDICleared 1.3.6.1.4.1.326.2.2.0.1040
This trap indicates that the Remote Defect Indication (RDI) has been removed from the incoming (terminating) virtual path. This trap is generated once when the virtual path is declared to be in the inactive RDI state.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxNonextendedModeViolation 1.3.6.1.4.1.326.2.2.0.1041
This trap indicates that a series D network module was inserted into a switch board running in non-extended mode. Multicast will not work on the series D module without removing all series B modules and rebooting the switch.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxUnsupportedNetworkModule 1.3.6.1.4.1.326.2.2.0.1042
This trap indicates that a unsupported network module was inserted into a switch.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxDualScpRedundancy 1.3.6.1.4.1.326.2.2.0.1043
This trap indicates that there is a change in the state of dual SCP Redundancy.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxIpFilterViolation 1.3.6.1.4.1.326.2.2.0.1049
An asxIpFilterViolation trap occurs when an incoming IP packet is unauthorized to enter the switch control port and has been dropped.
Status: current Access: read-only
NOTIFICATION-TYPE    

q2931AFRejectKnown 1.3.6.1.4.1.326.2.2.0.1053
This trap is generated whenever any q2931 UNI with Address Filtering enabled rejects a Setup request because the request matched a template with the action 'reject'. The variables sent in the trap identify the source and destination UNI for the call.
Status: current Access: read-only
NOTIFICATION-TYPE    

q2931AFRejectUnknown 1.3.6.1.4.1.326.2.2.0.1054
This trap is generated whenever any q2931 UNI with Address Filtering enabled rejects a Setup request because the address matched no template. The variables sent in the trap identify the source and destination UNI for the call.
Status: current Access: read-only
NOTIFICATION-TYPE    

q2931CreationFailure 1.3.6.1.4.1.326.2.2.0.1061
This trap is generated whenever a switch fails to create a UNI. This is most likely due to a resource limitation on the switch.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxPsCurrentDown 1.3.6.1.4.1.326.2.2.0.1068
This trap alerts that one ATM switch power supply had a curent failure. The power supply that failed is identified by the power supply index.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxPsCurrentUp 1.3.6.1.4.1.326.2.2.0.1069
This trap alerts that one ATM switch power supply that had a curent failure is now up. The power supply that is back up is identified by the power supply index.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxPs5VoltDown 1.3.6.1.4.1.326.2.2.0.1070
This trap alerts that one ATM switch power supply had a +5V failure. The power supply that failed is identified by the power supply index.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxPs5VoltUp 1.3.6.1.4.1.326.2.2.0.1071
This trap alerts that one ATM switch power supply that had a +5V failure is now up. The power supply that is back up is identified by the power supply index.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSwitchLoginDetected 1.3.6.1.4.1.326.2.2.0.1072
An asxSwitchLoginDetected trap signifies that a user logged in on the switch.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxSwitchLoginFailed 1.3.6.1.4.1.326.2.2.0.1073
An asxSwitchLoginFailed trap signifies that a user's attempt to log in on the switch failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

pnniTdbGuardbandResrvFail 1.3.6.1.4.1.326.2.2.0.1074
This trap is generated when guardband memory reserve for any of the PNNI TDB(Topology Database) related functionalites like creation,modification and deletion on objects like node, ptse,flags,interal prefixes,external prefixes and etc fails. The switch is low on memory.
Status: current Access: read-only
NOTIFICATION-TYPE    

pnniTdbInconsistentState 1.3.6.1.4.1.326.2.2.0.1075
This trap is generated when PNNI TDB(Topology Database) is in an unrecoverable error condition due to MALLOC and other TDB related faliures. When this happenes the associated logical node is shutdown and this trap is sent.The switch has to be rebooted to bring this PNNI logical node up again.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxShmem2OutputQueueCongested 1.3.6.1.4.1.326.2.2.0.1077
This trap indicates that the output queue for the given priority has exceeded its dedicated length, and has begun overflowing into the shared buffer space on the netmod.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxShmem2OutputQueueCellLoss 1.3.6.1.4.1.326.2.2.0.1078
This trap indicates that the output queue for the given priority has overflowed and cells have been dropped.
Status: current Access: read-only
NOTIFICATION-TYPE    

fabricLvl3Lookup 1.3.6.1.4.1.326.2.2.0.1080
This trap is generated when a fabric detects excessive level 3 lookup errors. The level 3 lookup count is read every second. If the lookup count is non-null for 5 consecutive seconds, then this trap is generated. If the errors continue, this trap will be generated continuously every 5 seconds. This trap can be caused by: a misconfigured PVC; bad hardware.
Status: current Access: read-only
NOTIFICATION-TYPE    

fabricCorrectedLookup 1.3.6.1.4.1.326.2.2.0.1081
This trap is generated when the SCP detects inconsistant information in the HDCOMP lookup. The switch has corrected the bad information in the HDCOMP lookup ASIC's data structures.
Status: current Access: read-only
NOTIFICATION-TYPE    

spvcRerouteInitiated 1.3.6.1.4.1.326.2.2.0.1090
This trap is sent when a SPVC is being re-routed due to a better path being found.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxQ2931Down 1.3.6.1.4.1.326.2.2.0.1091
This trap is generated whenever UNI signalling goes down.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxQ2931Up 1.3.6.1.4.1.326.2.2.0.1092
This trap is generated whenever UNI signalling goes up.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxFabricDown 1.3.6.1.4.1.326.2.2.0.1093
An asxFabricDown trap signifies that the sending protocol entity recognizes a failure in one of the ATM Switch fabric, that is identified by the board number. This is probably caused by a hot-swap of a fabric module.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxFabricUp 1.3.6.1.4.1.326.2.2.0.1094
An asxFabricUp trap signifies that the sending protocol entity recognizes a new operational ATM Switch fabric, that is identified by the board number. This is probably caused by a hot-swap of a fabric module.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxQ2931CallClearing 1.3.6.1.4.1.326.2.2.0.1095
This trap is generated whenever calls are cleared in a signalling interface for the following reasons. * Carrier loss * SONET alarms in case of SONE * VP failure
Status: current Access: read-only
NOTIFICATION-TYPE    

pnniSpvccDown 1.3.6.1.4.1.326.2.2.0.2004
This trap is sent when a SPVC call is cleared or deleted. The pnniSpvcSrcDownReason indicates if the call was cleared due to a better route being found or a network failure. It also may indicate SPVC deletion. This trap is only sent if pnniSpvcTrapMode is all.
Status: current Access: read-only
NOTIFICATION-TYPE    

pnniSpvccUp 1.3.6.1.4.1.326.2.2.0.2005
This trap is send when a SPVC call is established. It identifies the SPVC and the old and new cost. If the call has not been up before, the pnniSpvcSrcOldRouteCost will be -1. This trap is only sent if pnniSpvcTrapMode is failure or all.
Status: current Access: read-only
NOTIFICATION-TYPE    

pnniSpvccFail 1.3.6.1.4.1.326.2.2.0.2006
This trap is sent when a SPVC call that is down fails to get connected on 16 consecutive attempts. This trap is only sent if pnniSpvcTrapMode is failure or all.
Status: current Access: read-only
NOTIFICATION-TYPE    

pnniSpvpcDown 1.3.6.1.4.1.326.2.2.0.2007
This trap is sent when a SPVP call is cleared. The pnniSpvcSrcDownReason indicates if the call was cleared due to a better route being found or a network failure. It also may indicate SPVPC deletion. This trap is only sent if pnniSpvpcTrapMode is all.
Status: current Access: read-only
NOTIFICATION-TYPE    

pnniSpvpcUp 1.3.6.1.4.1.326.2.2.0.2008
This trap is send when a SPVP call is established. It identifies the SPVP and the old and new cost. If the call has not been up before, the pnniSpvcSrcOldRouteCost will be -1. This trap is only sent if pnniSpvpcTrapMode is all or failure.
Status: current Access: read-only
NOTIFICATION-TYPE    

pnniSpvpcFail 1.3.6.1.4.1.326.2.2.0.2009
This trap is sent when a SPVP call that is down fails to get connected on 16 consecutive attempts. This trap is only sent if pnniSpvpcTrapMode is all or failure.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxPortCardDown 1.3.6.1.4.1.326.2.2.0.2010
An asxPortCardDown trap signifies that the sending protocol entity recognizes a failure in one of the ATM Switch portcards, that is identified by the portcard name. This is probably caused by a hot-swap of the port card.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxPortCardUp 1.3.6.1.4.1.326.2.2.0.2011
An asxPortCardUp trap signifies that the sending protocol entity recognizes a new operational ATM Switch port card, that is identified by the portcard name. This is probably caused by a hot-swap of the port card.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxServiceCategoryOutputQueueCongested 1.3.6.1.4.1.326.2.2.0.2013
This trap indicates that the output queue for the service category has exceeded its dedicated length, and has begun overflowing into the shared buffer space on the netmod.
Status: current Access: read-only
NOTIFICATION-TYPE    

asxServiceCategoryOutputQueueCellLoss 1.3.6.1.4.1.326.2.2.0.2014
This trap indicates that the output queue for the given service category has overflowed and cells have been dropped.
Status: current Access: read-only
NOTIFICATION-TYPE    

pnniNormalToOverloadTransition 1.3.6.1.4.1.326.2.2.0.2015
This trap is generated on transition from the normal state to the overload state.
Status: current Access: read-only
NOTIFICATION-TYPE    

pnniOverloadToNormalTransition 1.3.6.1.4.1.326.2.2.0.2016
This trap is generated on transition from the overload to the normal state.
Status: current Access: read-only
NOTIFICATION-TYPE    

syslogFacility 1.3.6.1.4.1.326.2.2.2.1.22.1
The syslog facility string, possible values are daemon, local[0-7].
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER daemon(0), local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8)  

syslogConsoleState 1.3.6.1.4.1.326.2.2.2.1.22.2
The syslog console state, ON means syslog messages are sent to console.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

syslogDestinationTable 1.3.6.1.4.1.326.2.2.2.1.22.3
This table lists all the syslog destinations
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SyslogDestinationEntry

syslogDestinationEntry 1.3.6.1.4.1.326.2.2.2.1.22.3.1
A structure containing the parameters for a syslog destination
Status: current Access: not-accessible
OBJECT-TYPE    
  SyslogDestinationEntry  

syslogDestinationHost 1.3.6.1.4.1.326.2.2.2.1.22.3.1.1
The host IP address of the syslog destination
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

syslogDestinationStatus 1.3.6.1.4.1.326.2.2.2.1.22.3.1.2
Administrative status of this entry
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

pnniPmpRerouteInitiated 1.3.6.1.4.1.326.2.2.0.2020
This trap is sent when a party is being re-routed due to a better path being found or if a reroute is requested using a AMI command.
Status: current Access: read-write
NOTIFICATION-TYPE    

pnniPmpSpvcUp 1.3.6.1.4.1.326.2.2.0.2021
This trap is send when a pmp SPVC call is established. This trap is only sent if pnniSpvcTrapMode is failure or all.
Status: current Access: read-write
NOTIFICATION-TYPE    

pnniPmpSpvcDown 1.3.6.1.4.1.326.2.2.0.2022
This trap is sent when a pmp SPVC call is cleared. The pnniSpvcSrcDownReason indicates if the call was cleared due to a better route being found or a network failure. This trap is only sent if pnniSpvpcTrapMode is all.
Status: current Access: read-write
NOTIFICATION-TYPE    

pnniPmpSpvcFail 1.3.6.1.4.1.326.2.2.0.2023
This trap is sent when a SPVC call that is down fails to get connected on 16 consecutive attempts. This trap is only sent if pnniSpvcTrapMode is failure or all.
Status: current Access: read-write
NOTIFICATION-TYPE    

pnniSpvxRGroupSwover 1.3.6.1.4.1.326.2.2.0.2024
This trap is sent when a automatic switch over occurs in a SPVC Redundancy group that has automatic PVC switch over enabled.
Status: current Access: read-write
NOTIFICATION-TYPE    

asxSVXCPStateTransferFailed 1.3.6.1.4.1.326.2.2.0.2025
This trap is sent when the SVx/SPVx Preservation module is unable to transfer call and interface state information to the Standby SCP, due either to temporary unavailablility of system resources or to a permanent system error requiring a system reboot.
Status: current Access: read-write
NOTIFICATION-TYPE    

asxSVXCPStateTransferRestarted 1.3.6.1.4.1.326.2.2.0.2026
This trap is sent when the SVx/SPVx Preservation module has restarted its transfer of call and interface state information to the Standby SCP, which transfer was halted due to unavailablility of system resources.
Status: current Access: read-write
NOTIFICATION-TYPE    

asxSVXCPStateDroppedCall 1.3.6.1.4.1.326.2.2.0.2027
This trap is sent when the SVx/SPVx Preservation module has insufficient memory to store one or more calls during its transfer of call and interface state information to the Standby SCP. Such calls therefore will be lost (not preserved on switchover). This trap is sent only once, no matter how many calls suffer this fate. Recovering any lost calls is possible only by disabling and then re-enabling SVx/SPVx Preservation, in order to provoke a complete retrial of the transfer process.
Status: current Access: read-write
NOTIFICATION-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor