GDCSCM-MIB

File: GDCSCM-MIB.mib (29540 bytes)

Imported modules

RFC1155-SMI RFC-1215 RFC-1212
RFC1213-MIB GDCMACRO-MIB

Imported symbols

enterprises Gauge IpAddress
TRAP-TYPE OBJECT-TYPE DisplayString
SCinstance

Defined Types

ScmNodeEntry  
SEQUENCE    
  scmNodeIndex SCinstance
  scmNodeType INTEGER
  scmNodeConfigCs OCTET STRING
  scmNodeStatus INTEGER
  scmNodeAlarmScan INTEGER
  scmNodeLevel INTEGER
  scmNodeConfigChecksumStatus INTEGER
  scmNodeCurrentAlarms OCTET STRING
  scmNodeSerialNumber DisplayString
  scmNodeAdminStatus INTEGER
  scmNodeOperStatus INTEGER

ScmSlotEntry  
SEQUENCE    
  scmSlotNumber INTEGER
  scmSlotState INTEGER

ScmRedundancyEntry  
SEQUENCE    
  scmRedundancyIndex SCinstance
  scmEtherIPAddress IpAddress
  scmPPPIPAddress IpAddress
  scmRedundancySwitch INTEGER

Defined Values

gdc 1.3.6.1.4.1.498
OBJECT IDENTIFIER    

sc 1.3.6.1.4.1.498.3
OBJECT IDENTIFIER    

scmSystem 1.3.6.1.4.1.498.3.6
OBJECT IDENTIFIER    

scmVersion 1.3.6.1.4.1.498.3.6.1
OBJECT IDENTIFIER    

scmMaster 1.3.6.1.4.1.498.3.6.2
OBJECT IDENTIFIER    

scmNode 1.3.6.1.4.1.498.3.6.3
OBJECT IDENTIFIER    

scmShelf 1.3.6.1.4.1.498.3.6.4
OBJECT IDENTIFIER    

scmAlmTrap 1.3.6.1.4.1.498.3.6.5
OBJECT IDENTIFIER    

scmRedundancy 1.3.6.1.4.1.498.3.6.6
OBJECT IDENTIFIER    

scmMIBVersion 1.3.6.1.4.1.498.3.6.1.1
The version number of the MIB, to allow products to know which MIB is being supported. The version number will be x.yzT where x is a major revision (1-9), y is a minor revision(0-9), z is a typo revision (0-9) and T indicates the MIB is still a test revision(A-Z). When a release is complete no T should exist.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(5)  

scmBootVersion 1.3.6.1.4.1.498.3.6.1.2
The version number of the Boot Software, to allow products to know which Boot Software is being supported. The version number will be x.yzT where x is a major revision (1-9), y is a minor revision(0-9), z is a typo revision (0-9) and T indicates the Boot Software is still a test revision(A-Z). When a release is complete no T should exist.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(5)  

scmApplVersion 1.3.6.1.4.1.498.3.6.1.3
The version number of the Application Software, to allow products to know which Software is being supported. The version number will be x.yzT where x is a major revision (1-9), y is a minor revision(0-9), z is a typo revision (0-9) and T indicates the Software is still a test revision(A-Z). When a release is complete no T should exist.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(5)  

scmMasterTimeout 1.3.6.1.4.1.498.3.6.2.1
The Management bus timeout defined as the time between the last character being transmitted to the Network Element and the first character being received. This variable is defined in milliSeconds. The default timeout is 50.0 mS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 15..100  

scmAlarmScan 1.3.6.1.4.1.498.3.6.2.2
This is used to turn on and off the alarm scan feature to the Network Elements connected off of this SCM. If the alarm scan is turned off no Network Elements will be scanned for alarms and therefore no alarms will be sent to the controller. If alarms occur when the scan is off, they will be discarded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER alarmScanOn(1), alarmScanOff(2)  

scmTime 1.3.6.1.4.1.498.3.6.2.3
This is used to read or set the time of the real-time clock in the SCM. The format of the time will be hh:mm:ss. Where hh is the hour (01-24) in 24 hour format, mm is minutes (00-59) and ss is seconds (00-59)
Status: obsolete Access: read-write
OBJECT-TYPE    
  DisplayString Size(8)  

scmDate 1.3.6.1.4.1.498.3.6.2.4
This is used to read or set the date of the real-time clock in the SCM. The format of the date will be mm-dd-yy. Where mm is month (01-12), dd is the day (01-31), and yy is the year (00-99).
Status: obsolete Access: read-write
OBJECT-TYPE    
  DisplayString Size(8)  

scmRedundant 1.3.6.1.4.1.498.3.6.2.5
This is used to read the current state of a SCM
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER redundant(1), primary(2)  

scmShelfNumber 1.3.6.1.4.1.498.3.6.2.6
This indicates the number of shelves in the system. If it is a one shelf system, then a maximum of 16 Network Elements (including any SCM's). If it is a two shelf system, then a maximum of 32 Network Elements (including any SCM's) can exist.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER oneShelf(1), twoShelf(2)  

scmReset 1.3.6.1.4.1.498.3.6.2.7
This is used to reset the SCM card in the shelf. The SCM will respond to the command and then perform the reset. During the time the SCM resets, the SCM will not respond. The SCM reset is a hard reset, therefore a coldStart TRAP will be received. normal - This is the value that will be returned whenever this variable is read. reset - This value can be set to perform the reset.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), reset(2)  

scmPowerAvail 1.3.6.1.4.1.498.3.6.2.8
This is used to determine the total amount of power available to the shelves.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

scmDefaultConfig 1.3.6.1.4.1.498.3.6.2.9
This is used to allow the NonVolatile Configuration to be set to a factory default state. The SCM will perform a reset to make the default configuration take affect. The SCM reset is a hard reset, therefore a coldStart TRAP will be received. factoryApplDefault - This is used to clear all of Non-Volatile memory associated with the application. If this option is selected the Node table will be emptied and the Community Name Table will only contain 'public' as readOnly and the Trap Table will be empty.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), factoryApplDefault(2)  

scmPowerConsum 1.3.6.1.4.1.498.3.6.2.10
This is used to determine the amount of power consumed by all the managed network elements in the shelves managed by this SCM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

scmCannedConfig 1.3.6.1.4.1.498.3.6.2.11
This reads the dip switches and reports the current canned configuration setting.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER cannedConfigNone(1), cannedConfig1(2), cannedConfig2(3), cannedConfig3(4), cannedConfig4(5), cannedConfig5(6), cannedConfig6(7), cannedConfig7(8)  

scmSetNetworkElementRealTime 1.3.6.1.4.1.498.3.6.2.12
Number of seconds from midnight Dec 31, 1969. A set of this object will be broadcasted to every network element in the shelf. A get of this object will always return a 1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

scmDownLoadCode 1.3.6.1.4.1.498.3.6.2.13
This object determines if TFTP (Trivial File Transfer Protocol) code downloading to the SCM or any NEs is permitted. When management sets disable(2) any attempt to place the SCM in boot mode or download code to NEs will result in an TFTP error response indicating that the download request has been denied. The factory default is enable(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

scmOperatingMode 1.3.6.1.4.1.498.3.6.2.14
This object determines the operating mode of an SCM as it pertains to the management buss. Active - indicates the SCM is to possess full control of the shelf and its elements. This is the default for a primary SCM. Standby - indicates the SCM is operationg in redundant mode. This state applies only to an SCM whose dip switch is set to redundant. Sleep - indicates the primary SCM has been forced off the management buss. This value can never be set by network management and only pertains to an SCM whose dip switch is set to primary.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER active(1), standby(2), sleep(3)  

scmAliveTrapInterval 1.3.6.1.4.1.498.3.6.2.15
This object is used to set the time period, represented in minutes, in which the SCM will send an SNMP TRAP to the manager to indicate that it is alive. No trap is sent if the value is zero or if the scmOperatingMode is set to Sleep. The default value is zero for this object.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..60  

scmRedundantTimeOut 1.3.6.1.4.1.498.3.6.2.16
This object is used to set the time period, represented in seconds, in which the redundant SCM will wait after not receiving express polls from the primary SCM before it takes contol of the management buss. When set to zero, the redundant SCM will ignore the loss of express polls. The default is zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..300  

scmTelnet 1.3.6.1.4.1.498.3.6.2.17
This object determines if telnet to the SCM is permitted. When management sets disable(2) all attempts to telnet to the SCM will be rejected. The factory default is enable(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

scmTextAlarmTraps 1.3.6.1.4.1.498.3.6.2.18
This object changes the format of alarm traps from the managed network elements. If this object is set to disable then the SCM sends cmnAlarmStatusTrap traps. If this is set to enable and the network element supports text-style traps then the SCM sends scmAlarmTextTrap traps. The factory default is disable(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

scmNodeTable 1.3.6.1.4.1.498.3.6.3.2
A table that contains information about the nodes in the system. The SCM node is a special node in the table. The SCM itself adds the node to the table and it cannot be deleted by setting the status to invalid. The configuration checksum of the SCM is this node table (minus the SCM's configuration checksum), the community name table, the trap table and any ip addresses that are inputed through the terminal interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScmNodeEntry

scmNodeEntry 1.3.6.1.4.1.498.3.6.3.2.1
A list of information for each node in the system. To create an entry, must give the type field.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScmNodeEntry  

scmNodeIndex 1.3.6.1.4.1.498.3.6.3.2.1.1
The value indicates the node number for which this entry contains management information. The Node Index is based off of the IFindex in MIB-II. The Node Index value is used to indicate the slot, line and drop of the node that is being addressed. The index is defined as: ssllddxx where ss is from 1-32, ll from 1-128 and dd from 0-31. The xx is always zero in the Node table, but can be used by a network element type in their MIB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

scmNodeType 1.3.6.1.4.1.498.3.6.3.2.1.2
The value indicates the type of node located at the Node index.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER vf288(1), sc5001(2), sc5520(3), datx2011(4), nms520(5), sc700G2(6), sc700G3(7), dc730D1(8), dc730D2(9), dc720G1(10), dc720G2(11), sc616(12), dc610(13), dc612(14), sc702G2(15), nms510(16), sc5034(17), scdualV34(18), sc613(19), sc5553(20), sc611(21), dc621(22), sc710d2(23), sc700g2RP(24), nms553(25), sc710d2rp(26), dc720g2rp(27), dc730d2rp(28), mp7002(29), uas7616NZ(30), scm(31), sc521(32), sc5002(33), dc610NZ(34), mp7001(35), sc701T2(36), sc701T2RP(37), dc721T1(38), dc721T2(39), dc721T2RP(40), dc731D1(41), dc731D2(42), dc731D2RP(43), uas7616TA(44), uas7616(45), sc553(46), notlocallymanaged(47), uas7624(48), hdsl700AG2(49), hdsl700AG2NZ(50), uas7626(51), ntu2m(52), uas7022(53), gt128(54), gt128NZ(55), sc5090(56), gt1030(57), gt2030(58), sc800T3(59), uas7722(60), sc5034A(61), gt1020(62), gt2020(63), sc711D2(64), sc202(65), sc521A(66), uas7722xr(67), gt1030xr(68), uas780g2(69), gt1830(70), sc5506(71), sc5516(72)  

scmNodeConfigCs 1.3.6.1.4.1.498.3.6.3.2.1.3
The value indicates the configuration checksum of the node. It is not a required value when adding an entry to a table. A default value of 0(zero) will be used when the checksum is unknown.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

scmNodeStatus 1.3.6.1.4.1.498.3.6.3.2.1.4
The status of the entry. If read and the entry exists, valid(1) will always be returned. Invalid entries will be removed from the table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

scmNodeAlarmScan 1.3.6.1.4.1.498.3.6.3.2.1.5
This is used to turn on and off the alarm scan feature for a particular Network Element connected off of this SCM. If the alarm scan is turned off the Network Element will not be scanned for alarms and therefore no alarms will be sent to the controller for that NE. If alarms occur when the scan is off, they will be discarded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

scmNodeLevel 1.3.6.1.4.1.498.3.6.3.2.1.6
The value indicates the level that the node exists at. Nodes that are located in the shelf are usually defined as level 1. The level is used to determine the time the SCM allows for the node to respond. The higher the level the longer the timeout. The timeout is defined as follows: 2 * (level - 1) + 2 Second
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..4  

scmNodeConfigChecksumStatus 1.3.6.1.4.1.498.3.6.3.2.1.7
The value indicates whether the checksum in the NE matches that in the table the last time the information was received from a NE. The NE will send this information on power-up.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER correct(1), incorrect(2)  

scmNodeCurrentAlarms 1.3.6.1.4.1.498.3.6.3.2.1.8
Reads the alarm information current in the network element. The number of bytes in the alarm data is dependent on the type of network element that is being addressed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..255)  

scmNodeSerialNumber 1.3.6.1.4.1.498.3.6.3.2.1.9
This is used to get the serial number of the network element. This is also used to set the address of the unit by it's serial number in the case of remote units.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(16)  

scmNodeAdminStatus 1.3.6.1.4.1.498.3.6.3.2.1.10
This is used to set the desired state of the network element.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

scmNodeOperStatus 1.3.6.1.4.1.498.3.6.3.2.1.11
The current operational statue of the network element.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

scmSlotTable 1.3.6.1.4.1.498.3.6.4.1
A table that contains information about the state of the Network Elements in the shelf.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScmSlotEntry

scmSlotEntry 1.3.6.1.4.1.498.3.6.4.1.1
A list of information for each Network Element in the shelf.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScmSlotEntry  

scmSlotNumber 1.3.6.1.4.1.498.3.6.4.1.1.1
The value indicates the slot from which to read the current state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..32  

scmSlotState 1.3.6.1.4.1.498.3.6.4.1.1.2
The state of the Network Element in the shelf. Active means that all commands to and from the Network Element have had correct responses with no communication errors. Inactive means that the Network Element does not respond to any commands. Active with Errors means that responses are received, but communication errors are occuring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER activestate(1), inactivestate(2), activeerrorstate(3)  

scmAlarmText 1.3.6.1.4.1.498.3.6.7
The variable associated with scmAlarmTextTrap. A get will always return a null string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(100)  

scmAlarmTrap 1
This is the Alarm Trap. This trap is sent whenever a network element detects a change in its alarm information.
TRAP-TYPE    

scmExpressPollTrap 2
This is the Express Poll Trap. It will be used to indicate a state change in a slot in the shelf.
TRAP-TYPE    

scmPowerSupplyTrap 3
This is the Power Supply Trap. It will be used to indicate a change in the amount of power available to the shelf. This change will occur when a power supply card has either failed or has been physically replaced.
TRAP-TYPE    

scmAliveTrap 4
This is the SCM Alive Trap. It is used to notify the manager every N minutes that it is still alive.
TRAP-TYPE    

scmConfigChksumTrap 5
This is the configuration checksum change trap. When the configuration checksum of a network element changes then the SCM sends this trap to notify the manager of the change.
TRAP-TYPE    

scmAlarmTextTrap 6
This trap is sent when an alarm is received from a network element and scmTextAlarmTraps is set to enable and the network element supports text-style traps. The variable is scmAlarmText which is a display string of the form: NNN: Slot x Line y Drop z alarm name is Active (or Inactive), where NNN is the network element name which corresponds to scmNodeType. Example: SC553: Slot 2 Line 1 Drop 0 DCD Loss Alarm is Active
TRAP-TYPE    

scmRedundancyTable 1.3.6.1.4.1.498.3.6.6.2
A table that contains information about the SCM's in the system as they pertain to redundancy.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScmRedundancyEntry

scmRedundancyEntry 1.3.6.1.4.1.498.3.6.6.2.1
A list of information for each SCM in the shelf as it pertains to redundancy.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScmRedundancyEntry  

scmRedundancyIndex 1.3.6.1.4.1.498.3.6.6.2.1.1
The value indicates the addressing/indexing method of accessing the objects in this table. The SCinstance represents the shelf's Slot, Line, Drop and interface address. Drop and interface will always be zero for an SCM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

scmEtherIPAddress 1.3.6.1.4.1.498.3.6.6.2.1.2
This object is used to obtain the Ethernet IP Address of the SCM in ###.###.###.### format.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

scmPPPIPAddress 1.3.6.1.4.1.498.3.6.6.2.1.3
This object is used to obtain the PPP IP Address of the SCM in ###.###.###.### format.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

scmRedundancySwitch 1.3.6.1.4.1.498.3.6.6.2.1.4
This is used to read the current state of the redundant switch on a SCM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER redundant(1), primary(2)