H3C-EPON-DEVICE-MIB

File: H3C-EPON-DEVICE-MIB.mib (66558 bytes)

Imported modules

HUAWEI-3COM-OID-MIB SNMPv2-SMI SNMPv2-TC
IF-MIB SNMPv2-CONF SNMP-FRAMEWORK-MIB

Imported symbols

h3cEpon MODULE-IDENTITY mib-2
OBJECT-TYPE Counter32 Unsigned32
Integer32 zeroDotZero TruthValue
DateAndTime RowStatus MacAddress
ifIndex MODULE-COMPLIANCE OBJECT-GROUP
SnmpAdminString

Defined Types

H3cEponDeviceControlEntry  
SEQUENCE    
  h3cEponDeviceObjectReset INTEGER
  h3cEponDeviceObjectModes INTEGER
  h3cEponDeviceObjectFecEnabled INTEGER
  h3cEponDeviceObjectOamMode INTEGER
  h3cEponDeviceObjectDeviceReadyMode INTEGER
  h3cEponDeviceObjectPowerDown TruthValue
  h3cEponDeviceObjectNumberOfLLIDs Integer32
  h3cEponDeviceObjectReportThreshold Integer32
  h3cEponDeviceRemoteMACAddressLLIDControl INTEGER

H3cEponDeviceRemoteMACAddressLLIDEntry  
SEQUENCE    
  h3cEponDeviceRemoteMACAddressLLIDName SnmpAdminString
  h3cEponDeviceRMadlLLID Unsigned32
  h3cEponDeviceRMadlLogID OBJECT IDENTIFIER
  h3cEponDeviceRMadlRemoteAddress MacAddress
  h3cEponDeviceRMadlType INTEGER
  h3cEponDeviceRMadlAction INTEGER
  h3cEponDeviceRMadlEntryStatus RowStatus

H3cEponDeviceStatEntry  
SEQUENCE    
  h3cEponDeviceStatTxFramesQueue0 Counter32
  h3cEponDeviceStatTxFramesQueue1 Counter32
  h3cEponDeviceStatTxFramesQueue2 Counter32
  h3cEponDeviceStatTxFramesQueue3 Counter32
  h3cEponDeviceStatTxFramesQueue4 Counter32
  h3cEponDeviceStatTxFramesQueue5 Counter32
  h3cEponDeviceStatTxFramesQueue6 Counter32
  h3cEponDeviceStatTxFramesQueue7 Counter32
  h3cEponDeviceStatRxFramesQueue0 Counter32
  h3cEponDeviceStatRxFramesQueue1 Counter32
  h3cEponDeviceStatRxFramesQueue2 Counter32
  h3cEponDeviceStatRxFramesQueue3 Counter32
  h3cEponDeviceStatRxFramesQueue4 Counter32
  h3cEponDeviceStatRxFramesQueue5 Counter32
  h3cEponDeviceStatRxFramesQueue6 Counter32
  h3cEponDeviceStatRxFramesQueue7 Counter32
  h3cEponDeviceStatDroppedFramesQueue0 Counter32
  h3cEponDeviceStatDroppedFramesQueue1 Counter32
  h3cEponDeviceStatDroppedFramesQueue2 Counter32
  h3cEponDeviceStatDroppedFramesQueue3 Counter32
  h3cEponDeviceStatDroppedFramesQueue4 Counter32
  h3cEponDeviceStatDroppedFramesQueue5 Counter32
  h3cEponDeviceStatDroppedFramesQueue6 Counter32
  h3cEponDeviceStatDroppedFramesQueue7 Counter32

H3cEponDeviceEventObjectEntry  
SEQUENCE    
  h3cEponDeviceSampleMinimum Integer32
  h3cEponDeviceDyingGaspAlarmState TruthValue
  h3cEponDeviceDyingGaspAlarmEnabled TruthValue
  h3cEponDeviceCriticalEventState TruthValue
  h3cEponDeviceCriticalEventEnabled TruthValue
  h3cEponDeviceLocalLinkFaultAlarmState TruthValue
  h3cEponDeviceLocalLinkFaultAlarmEnabled TruthValue
  h3cEponDeviceTemperatureEventIndicationState TruthValue
  h3cEponDeviceTemperatureEventIndicationEnabled TruthValue
  h3cEponDevicePowerVoltageEventIndicationState TruthValue
  h3cEponDevicePowerVoltageEventIndicationEnabled TruthValue
  h3cEponDeviceGlobalEventState TruthValue
  h3cEponDeviceGlobalEventEnabled TruthValue
  h3cEponDeviceErroredSymbolPeriodEventState TruthValue
  h3cEponDeviceErroredSymbolPeriodEventEnabled TruthValue
  h3cEponDeviceErroredFrameEventState TruthValue
  h3cEponDeviceErroredFrameEventEnabled TruthValue
  h3cEponDeviceErroredFramePeriodEventState TruthValue
  h3cEponDeviceErroredFramePeriodEventEnabled TruthValue
  h3cEponDeviceErroredFrameSecondsSummaryEventState TruthValue
  h3cEponDeviceErroredFrameSecondsSummaryEventEnabled TruthValue
  h3cEponDeviceOrganizationSpecificEventState TruthValue
  h3cEponDeviceOrganizationSpecificEventEnabled TruthValue
  h3cEponDeviceEventControl INTEGER

H3cEponDeviceEventsLogEntry  
SEQUENCE    
  h3cEponDeviceEventsLogName SnmpAdminString
  h3cEponDeviceEventsLogIndex Unsigned32
  h3cEponDeviceEventsLogID OBJECT IDENTIFIER
  h3cEponDeviceEventsLogFirstTime DateAndTime
  h3cEponDeviceEventsLogLastTime DateAndTime
  h3cEponDeviceEventsLogCounts Counter32
  h3cEponDeviceEventsLogType INTEGER
  h3cEponDeviceEventsLogEntryStatus RowStatus

Defined Values

h3cEponDeviceMIB 1.3.6.1.4.1.2011.10.2.42.4
The objects in this MIB module are used to manage Ethernet Passive Optical Network (EPON) devices which are based on the Ethernet in the First Mile (EFM) PON as defined in IEEE Draft P802.3ah/D3.0 clause 60,64,65. This mib is excerpted from the draft files directly,only changed the object name,added the h3c as prefix. The following reference is used throughout this MIB module: [802.3ah] refers to: IEEE Draft P802.3ah/D3.3: 'Draft amendment to - Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications - Media Access Control Parameters, Physical Layers and Management Parameters for subscriber access networks', 22 April 2004. Of particular interest are Clause 64(MPCP) 65(P2mP RS) and 60 (PON PMDs). Clause 30, 'Management', and Clause 45,'Management Data Input/Output (MDIO) Interface'. Copyright (C) The Internet Society (2004). This version of this MIB module is part of XXXX see the RFC itself for full legal notices.
MODULE-IDENTITY    

h3cEponDeviceObjectMIB 1.3.6.1.4.1.2011.10.2.42.4.1
OBJECT IDENTIFIER    

h3cEponDeviceObjects 1.3.6.1.4.1.2011.10.2.42.4.1.1
OBJECT IDENTIFIER    

h3cEponDeviceConformance 1.3.6.1.4.1.2011.10.2.42.4.1.2
OBJECT IDENTIFIER    

h3cEponDeviceControlObjects 1.3.6.1.4.1.2011.10.2.42.4.1.1.1
OBJECT IDENTIFIER    

h3cEponDeviceStatObjects 1.3.6.1.4.1.2011.10.2.42.4.1.1.2
OBJECT IDENTIFIER    

h3cEponDeviceEventObjects 1.3.6.1.4.1.2011.10.2.42.4.1.1.3
OBJECT IDENTIFIER    

h3cEponDeviceControlTable 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.1
Table for EPON device MIB modules.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponDeviceControlEntry

h3cEponDeviceControlEntry 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.1.1
An entry in the EPON device Control table.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponDeviceControlEntry  

h3cEponDeviceObjectReset 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.1.1.1
This variable is used to reset the EPON device. The interface may be unavailable while the reset occurs and data may be lost. During reading operation it returns the state of the EPON device. running(1) indicates and operates normal operation, reset(2) indicates and operates reset mode. Writing can be done all the time.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER running(1), reset(2)  

h3cEponDeviceObjectModes 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.1.1.2
This variable defines the mode of the EPON device. When an olt(1) it is an Optical Line Terminal device (server) and when an onu(2) and Optical Network Unit device (client)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER olt(1), onu(2)  

h3cEponDeviceObjectFecEnabled 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.1.1.4
This variable defines and provides information whether the EPON device uses FEC as defined in the [802.3ah] clause 65.2 for EPON. When noFECEnabled(1) the device does not support FEC mode When fecTxEnabled(2) the device supports the FEC transmission mode. When fecRxEnabled(3) the device supports the FEC Receive mode. When fecTxRxEnabled(4) the device supports the FEC transmission and receive mode. Writing can be done all the time. This attribute is relevant for an OLT and an ONU.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noFecEnabled(1), fecTxEnabled(2), fecRxEnabled(3), fecTxRxEnabled(4)  

h3cEponDeviceObjectOamMode 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.1.1.5
This variable defines and provides information on the Operation Administration and Maintenance (OAM) mode of an EPON device as defined by the [802.3ah] clause 57. When noOam(1) the device does not supports the OAM mode. When oamServer(2) the device supports the OAM mode as a server unit. When oamClient(3) the device supports the OAM mode as a client unit. Writing can be done during initialization, h3cEponDeviceObjectDeviceReadyMode is in notReady(1) or inProcess(2). This attribute is relevant for an OLT and an ONU.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noOam(1), oamServer(2), oamclient(3)  

h3cEponDeviceObjectDeviceReadyMode 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.1.1.6
This variable defines the mode of an EPON device and provides information on the mode in initialization - ready for registration as defined by the [802.3ah] clause 64. When notReady(1) the device is not ready for operation. When inProcess(2) the device is in initialization process. When ready(3) the device is ready for registration. Writing can be done all the time. This attribute is relevant for an OLT and an ONU.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notReady(1), inProcess(2), ready(3)  

h3cEponDeviceObjectPowerDown 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.1.1.7
Setting this variable to True(1) will cause Device to be entered into Power down mode where no registration is allowed and only receiving data from the link. Writing can be done all the time. This attribute is relevant for an OLT and an ONU.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceObjectNumberOfLLIDs 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.1.1.8
A read only variable which defines the number of registered LLIDs (as defined by the [802.3ah] clause 65) in a EPON network for an OLT and an ONU. Initialization value is 0. This attribute is relevant for an OLT and an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cEponDeviceObjectReportThreshold 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.1.1.9
A set of 8 integers, for each LLID, that defines the threshold reporting for each Queue in the REPORT message, as defined in [802.3ah] 64. First Queue set reporting will provide information on the queue occupancy of frames below this Threshold. The value returned shall be in Time quanta (TQ) which is 16nsec or 2 octets increments. Writing can be done all the time. This attribute is relevant for an OLT and an ONU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

h3cEponDeviceRemoteMACAddressLLIDControl 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.1.1.10
Indicates and controls the resetting of the LLID MAC address log. Setting this object to none(1) has no action resetLog(2) empties the LLID MAC address log. All data is deleted. Setting it to useDefaultReporting(3) returns all entries priorities to their factory-default reporting. Reading this object always returns useDefaultReporting(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), resetLog(2), useDefaultReporting(3)  

h3cEponDeviceRemoteMACAddressLLIDTable 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.2
A table of read-only value that identifies the source_address and LLIDs parameter of the remote devices in the network. This MacAddress value, as defined in [802.3ah], 30.3.5.1.5, is updated on reception of a valid frame with a unicast destination Field or (1) a destination Field equal to the reserved multicast address for MAC Control specified in [802.3ah] Annex 31A, (2) lengthOrType field value equal to the reserved Type for MAC Control as specified in [802.3ah] Annex 31A. (3)an MPCP subtype value equal to the subtype reserved for MPCP as specified in [802.3ah] Annex 31A, and an LLID as allocated by the OLT. The table is defined as Remote MAC address - LLID (RMadL) The table is relevant only for an OLT device, and is equivalent from a bridge emulation to the bridge port-MAC address table where the LLIDs are equivalent to virtual bridge ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponDeviceRemoteMACAddressLLIDEntry

h3cEponDeviceRemoteMACAddressLLIDEntry 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.2.1
A group of entries. Applications create and delete entries using h3cEponDeviceRMadlEntryStatus. When adding objects to an LLID they are added in the persistent order of their index in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponDeviceRemoteMACAddressLLIDEntry  

h3cEponDeviceRemoteMACAddressLLIDName 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.2.1.1
A locally-unique, administratively assigned name for a group of entries.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

h3cEponDeviceRMadlLLID 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.2.1.2
An arbitrary integer for the purpose of identifying the LLID. Writing can be done all the time.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..4294967295  

h3cEponDeviceRMadlLogID 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.2.1.3
The object identifier of a MIB module object to add to an entry, indicating the entry ID in the table. Writing can be done all the time.
Status: current Access: read-create
OBJECT-TYPE    
  OBJECT IDENTIFIER  

h3cEponDeviceRMadlRemoteAddress 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.2.1.4
The remote MAC address of the LLID. Writing can be done all the time.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

h3cEponDeviceRMadlType 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.2.1.5
A list of types for entries - LLIDs. Indicates and defines the state of registration. notRegister(1) marks a non registered LID, registered(2) marks a registered LLID. Writing can be done all the time.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER notRegister(1), registered(2)  

h3cEponDeviceRMadlAction 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.2.1.6
A list of actions for an entry - LLID. Indicates and defines the state of registration for the remote device. none(1) marks no action, register(2) marks to register an LLID, deregister(3) marks to deregister an LLID, reregister(4) marks reregistered LLID. Writing can be done all the time.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), register(2), deregister(3), reregister(4)  

h3cEponDeviceRMadlEntryStatus 1.3.6.1.4.1.2011.10.2.42.4.1.1.1.2.1.7
The control that allows creation and deletion of entries. Once made active an entry MAY not be modified except to delete it.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

h3cEponDeviceStatTable 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1
This table defines the list of statistics counters of EPON devices. The attributes are relevant for an OLT and an ONU.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponDeviceStatEntry

h3cEponDeviceStatEntry 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1
Table entries for Table of statistics counters of EPON devices.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponDeviceStatEntry  

h3cEponDeviceStatTxFramesQueue0 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.1
A count of the number of times a -Queue-0- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-0-. The -Queue-0- marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatTxFramesQueue1 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.2
A count of the number of times a -Queue-1- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-1-. The -Queue-1- marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatTxFramesQueue2 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.3
A count of the number of times a -Queue-2- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-2-. The -Queue-2- marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatTxFramesQueue3 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.4
A count of the number of times a -Queue-3- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-3-. The -Queue-3- marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatTxFramesQueue4 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.5
A count of the number of times a -Queue-4- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-4-. The -Queue-4- marking matched the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatTxFramesQueue5 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.6
A count of the number of times a -Queue-5- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-5-. The -Queue-5- marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatTxFramesQueue6 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.7
A count of the number of times a -Queue-6- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-6-. The -Queue-6- marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatTxFramesQueue7 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.8
A count of the number of times a -Queue-7- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-7-. The -Queue-7- marking matched the REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatRxFramesQueue0 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.9
A count of the number of times a -Queue-0- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-0-. The -Queue-0- marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatRxFramesQueue1 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.10
A count of the number of times a -Queue-1- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-1-. The -Queue-1- marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatRxFramesQueue2 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.11
A count of the number of times a -Queue-2- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-2-. The -Queue-2- marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatRxFramesQueue3 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.12
A count of the number of times a -Queue-3- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-3-. The -Queue-3- marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatRxFramesQueue4 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.13
A count of the number of times a -Queue-4- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-4-. The -Queue-4- marking matched the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatRxFramesQueue5 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.14
A count of the number of times a -Queue-5- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-5-. The -Queue-5- marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatRxFramesQueue6 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.15
A count of the number of times a -Queue-6- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-6-. The -Queue-6- marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatRxFramesQueue7 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.16
A count of the number of times a -Queue-7- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-7-. The -Queue-7- marking matched the REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatDroppedFramesQueue0 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.17
A count of the number of times a -Queue-0- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-0-. The -Queue-0- marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatDroppedFramesQueue1 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.18
A count of the number of times a -Queue-1- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-1-. The -Queue-1- marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatDroppedFramesQueue2 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.19
A count of the number of times a -Queue-2- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-2-. The -Queue-2- marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatDroppedFramesQueue3 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.20
A count of the number of times a -Queue-3- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-3-. The -Queue-3- marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatDroppedFramesQueue4 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.21
A count of the number of times a -Queue-4- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-4-. The -Queue-4- marking matched the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatDroppedFramesQueue5 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.22
A count of the number of times a -Queue-5- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-5-. The -Queue-5- marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatDroppedFramesQueue6 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.23
A count of the number of times a -Queue-6- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-6-. The -Queue-6- marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceStatDroppedFramesQueue7 1.3.6.1.4.1.2011.10.2.42.4.1.1.2.1.1.24
A count of the number of times a -Queue-7- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-7-. The -Queue-7- marking matched the REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceEventObjectTable 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1
This table defines the Event Objects for EPON devices. The attributes are relevant for an OLT and an ONU.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponDeviceEventObjectEntry

h3cEponDeviceEventObjectEntry 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1
Table entries for Table of Event objects for EPON devices.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponDeviceEventObjectEntry  

h3cEponDeviceSampleMinimum 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.1
The minimum Frequency of events this system will accept. A system may use the larger values of this minimum to lessen the impact of constant sampling. For larger sampling intervals the system samples less often and suffers less overhead. Unless explicitly resource limited, a system's value for this object SHOULD be 1, allowing as small as a 1 second interval for ongoing trigger sampling. Writing of the value can be done all the time.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cEponDeviceDyingGaspAlarmState 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.2
A read-only variable, which defines the state of the Dying Gasp indication of the OAM alarm indications as described in the [802.3ah] clause 57. When true the device has a dying gasp alarm asserted. When false the dying gasp alarm is reset
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceDyingGaspAlarmEnabled 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.3
A control to allow DyingGaspAlarm event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceCriticalEventState 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.4
A read-only variable, which defines the state of the Critical Event indication of the OAM alarm indications as described in the [802.3ah] clause 57. When true the device has a Critical Event asserted. When false the Critical Event is reset.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceCriticalEventEnabled 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.5
A control to allow CriticalEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceLocalLinkFaultAlarmState 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.6
A read-only variable, which defines the state of the Local Link Fault indication of the OAM alarm indications as described in the [802.3ah] clause 57. When true the device has a Local Link Fault alarm asserted. When false the Local Link Fault alarm is reset.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceLocalLinkFaultAlarmEnabled 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.7
A control to allow LocalLinkFaultAlarm event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceTemperatureEventIndicationState 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.8
A read-only variable, which defines the state of the Temperature Event indication of an EPON device. When condition of box temperature is above the threshold defined the alarm is asserted. When the condition is below that threshold the alarm is de-asserted. When true the device has a Temperature Event Indication asserted. When false the Temperature Event Indication is reset.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceTemperatureEventIndicationEnabled 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.9
A control to allow TemperatureEventIndication event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponDevicePowerVoltageEventIndicationState 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.10
A read-only variable, which defines the state of the Power/Voltage Event Indication of an EPON device. When condition of box Power/voltage is above the threshold defined the alarm is asserted. When the condition is below that threshold the alarm is de-asserted. When true the device has a Power/Voltage Event Indication asserted. When false the Power/Voltage Event Indication is reset.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

h3cEponDevicePowerVoltageEventIndicationEnabled 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.11
A control to allow PowerVoltageEventIndication event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceGlobalEventState 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.12
A read-only variable, which defines the state of the Global Event indication of an EPON device. When the indication of the event input occurs the event is asserted. When the input is removed that event is de-asserted. When true the device has a Global Event asserted. When false the Global Event Indication is reset.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceGlobalEventEnabled 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.13
A control to allow GlobalEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceErroredSymbolPeriodEventState 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.14
A read-only variable, which defines the state of the Errored Symbol Period Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Symbol Period Event asserted. When false the Errored Symbol Period Event is reset.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceErroredSymbolPeriodEventEnabled 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.15
A control to allow ErroredSymbolPeriodEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceErroredFrameEventState 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.16
A read-only variable, which defines the state of the Errored Frame Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Frame Event asserted. When false the Errored Frame Event is reset.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceErroredFrameEventEnabled 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.17
A control to allow ErroredFrameEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceErroredFramePeriodEventState 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.18
A read-only variable, which defines the state of the Errored Frame Period Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Frame Period Event asserted. When false the Errored Frame Period Event is reset.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceErroredFramePeriodEventEnabled 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.19
A control to allow ErroredFramePeriodEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceErroredFrameSecondsSummaryEventState 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.20
A read-only variable, which defines the state of the Errored Frame Seconds Summary Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Frame Seconds Summary Event asserted. When false the Errored Frame Seconds Summary Event is reset.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceErroredFrameSecondsSummaryEventEnabled 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.21
A control to allow ErroredFrameSecondsSummaryEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceOrganizationSpecificEventState 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.22
A read-only variable, which defines the state of the Organization Specific Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Organization Specific Event asserted. When false the Organization Specific Event is reset.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceOrganizationSpecificEventEnabled 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.23
A control to allow OrganizationSpecificEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cEponDeviceEventControl 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.1.1.24
Indicates and controls the resetting of the Event log. Setting this object to none(1) has no action resetLog(2) empties the event log. All data is deleted. Setting it to useDefaultReporting(3) returns all event priorities to their factory-default reporting. Reading this object always returns useDefaultReporting(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), resetLog(2), useDefaultReporting(3)  

h3cEponDeviceEventsLogTable 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.2
A table of objects provides a log of notification based on the event as pointed to by entries in those tables. The intent is a MAC level event log (set of events to when they happened). This attribute is relevant for an OLT and an ONU.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cEponDeviceEventsLogEntry

h3cEponDeviceEventsLogEntry 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.2.1
A group of Events. Applications create and delete entries using h3cEponDeviceEventsEntryStatus. When adding objects to a notification they are added in the lexical order of their index in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cEponDeviceEventsLogEntry  

h3cEponDeviceEventsLogName 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.2.1.1
A locally-unique, administratively assigned name for a group of Events.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

h3cEponDeviceEventsLogIndex 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.2.1.2
An arbitrary integer for the purpose of identifying individual Events within a h3cEponDeviceEventsLogName group. Events within a group are placed in the notification in the numerical order of this index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

h3cEponDeviceEventsLogID 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.2.1.3
The object identifier of a MIB module object to add to a Notification that results from the event. Writing can be done all the time.
Status: current Access: read-create
OBJECT-TYPE    
  OBJECT IDENTIFIER  

h3cEponDeviceEventsLogFirstTime 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.2.1.4
The time that an entry was created.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

h3cEponDeviceEventsLogLastTime 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.2.1.5
If multiple events are reported via the same entry, the time that the last event for this entry occurred, otherwise this should have the same value as h3cEponDeviceEventsLogFirstTime.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

h3cEponDeviceEventsLogCounts 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.2.1.6
The number of consecutive event instances reported by this entry. This starts at 1 with the creation of this row and increments by 1 for each subsequent duplicate event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cEponDeviceEventsLogType 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.2.1.7
A list of types for Events. Events are ordered according to their significance where 1 is the highest severity. h3cEponDeviceDyingGaspAlarmState(1) indicates a Dying Gasp Alarm State, h3cEponDeviceCriticalEventState(2) indicates a Critical Event State, h3cEponDeviceLocalLinkFaultAlarmState(3) indicates a Local Link Fault Alarm State, h3cEponDeviceTemperatureEventIndicationState(4) indicates a Temperature Event Indication State, h3cEponDevicePowerVoltageEventIndicationState(5) indicates a Power Voltage Event Indication State, h3cEponDeviceGlobalEventState(6) indicates a Global Event State, h3cEponDeviceErroredSymbolPeriodEventState(7) indicates an Errored Symbol Period Event State, h3cEponDeviceErroredFrameEventState(8) indicates an Errored Frame Event State, h3cEponDeviceErroredFramePeriodEventState(9) indicates an Errored Frame Period Event State, h3cEponDeviceErroredFrameSecondsSummaryEventState(10) indicates an Errored Frame Seconds Summary Event State, h3cEponDeviceOrganizationSpecificEventState(11) indicates an Organization Specific Event State.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER h3cEponDeviceDyingGaspAlarmState(1), h3cEponDeviceCriticalEventState(2), h3cEponDeviceLocalLinkFaultAlarmState(3), h3cEponDeviceTemperatureEventIndicationState(4), h3cEponDevicePowerVoltageEventIndicationState(5), h3cEponDeviceGlobalEventState(6), h3cEponDeviceErroredSymbolPeriodEventState(7), h3cEponDeviceErroredFrameEventState(8), h3cEponDeviceErroredFramePeriodEventState(9), h3cEponDeviceErroredFrameSecondsSummaryEventState(10), h3cEponDeviceOrganizationSpecificEventState(11)  

h3cEponDeviceEventsLogEntryStatus 1.3.6.1.4.1.2011.10.2.42.4.1.1.3.2.1.8
The control that allows creation and deletion of entries. Once made active an entry MAY not be modified except to delete it.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

h3cEponDeviceGroups 1.3.6.1.4.1.2011.10.2.42.4.1.2.1
OBJECT IDENTIFIER    

h3cEponDeviceGroupControl 1.3.6.1.4.1.2011.10.2.42.4.1.2.1.1
A collection of objects of h3cEponDevice control definition.
Status: current Access: read-create
OBJECT-GROUP    

h3cEponDeviceGroupRMadLTable 1.3.6.1.4.1.2011.10.2.42.4.1.2.1.2
A collection of objects of h3cEponDevice remote Mac address to LLID table.
Status: current Access: read-create
OBJECT-GROUP    

h3cEponDeviceGroupStat 1.3.6.1.4.1.2011.10.2.42.4.1.2.1.3
A collection of objects of EPON device Statistics
Status: current Access: read-create
OBJECT-GROUP    

h3cEponDeviceGroupEvent 1.3.6.1.4.1.2011.10.2.42.4.1.2.1.4
A collection of objects for EPON device Events
Status: current Access: read-create
OBJECT-GROUP    

h3cEponDeviceGroupEventLog 1.3.6.1.4.1.2011.10.2.42.4.1.2.1.5
A collection of objects for EPON device Events log
Status: current Access: read-create
OBJECT-GROUP    

h3cEponDeviceCompliances 1.3.6.1.4.1.2011.10.2.42.4.1.2.2
OBJECT IDENTIFIER    

h3cEponDeviceCompliance 1.3.6.1.4.1.2011.10.2.42.4.1.2.2.1
The compliance statement for EPON Devices.
Status: current Access: read-create
MODULE-COMPLIANCE