HH3C-EPON-DEVICE-MIB

File: HH3C-EPON-DEVICE-MIB.mib (65933 bytes)

Imported modules

HH3C-OID-MIB	SNMPv2-SMI	SNMPv2-TC
IF-MIB	SNMPv2-CONF	SNMP-FRAMEWORK-MIB

Imported symbols

hh3cEpon	MODULE-IDENTITY	mib-2
OBJECT-TYPE	Counter32	Unsigned32
Integer32	zeroDotZero	TruthValue
DateAndTime	RowStatus	MacAddress
ifIndex	MODULE-COMPLIANCE	OBJECT-GROUP
SnmpAdminString

Defined Types

Hh3cEponDeviceControlEntry
SEQUENCE
	hh3cEponDeviceObjectReset	INTEGER
	hh3cEponDeviceObjectModes	INTEGER
	hh3cEponDeviceObjectFecEnabled	INTEGER
	hh3cEponDeviceObjectOamMode	INTEGER
	hh3cEponDeviceObjectDeviceReadyMode	INTEGER
	hh3cEponDeviceObjectPowerDown	TruthValue
	hh3cEponDeviceObjectNumberOfLLIDs	Integer32
	hh3cEponDeviceObjectReportThreshold	Integer32
	hh3cEponDeviceRemoteMACAddressLLIDControl	INTEGER

Hh3cEponDeviceRemoteMACAddressLLIDEntry
SEQUENCE
	hh3cEponDeviceRemoteMACAddressLLIDName	SnmpAdminString
	hh3cEponDeviceRMadlLLID	Unsigned32
	hh3cEponDeviceRMadlLogID	OBJECT IDENTIFIER
	hh3cEponDeviceRMadlRemoteAddress	MacAddress
	hh3cEponDeviceRMadlType	INTEGER
	hh3cEponDeviceRMadlAction	INTEGER
	hh3cEponDeviceRMadlEntryStatus	RowStatus

Hh3cEponDeviceStatEntry
SEQUENCE
	hh3cEponDeviceStatTxFramesQueue0	Counter32
	hh3cEponDeviceStatTxFramesQueue1	Counter32
	hh3cEponDeviceStatTxFramesQueue2	Counter32
	hh3cEponDeviceStatTxFramesQueue3	Counter32
	hh3cEponDeviceStatTxFramesQueue4	Counter32
	hh3cEponDeviceStatTxFramesQueue5	Counter32
	hh3cEponDeviceStatTxFramesQueue6	Counter32
	hh3cEponDeviceStatTxFramesQueue7	Counter32
	hh3cEponDeviceStatRxFramesQueue0	Counter32
	hh3cEponDeviceStatRxFramesQueue1	Counter32
	hh3cEponDeviceStatRxFramesQueue2	Counter32
	hh3cEponDeviceStatRxFramesQueue3	Counter32
	hh3cEponDeviceStatRxFramesQueue4	Counter32
	hh3cEponDeviceStatRxFramesQueue5	Counter32
	hh3cEponDeviceStatRxFramesQueue6	Counter32
	hh3cEponDeviceStatRxFramesQueue7	Counter32
	hh3cEponDeviceStatDroppedFramesQueue0	Counter32
	hh3cEponDeviceStatDroppedFramesQueue1	Counter32
	hh3cEponDeviceStatDroppedFramesQueue2	Counter32
	hh3cEponDeviceStatDroppedFramesQueue3	Counter32
	hh3cEponDeviceStatDroppedFramesQueue4	Counter32
	hh3cEponDeviceStatDroppedFramesQueue5	Counter32
	hh3cEponDeviceStatDroppedFramesQueue6	Counter32
	hh3cEponDeviceStatDroppedFramesQueue7	Counter32

Hh3cEponDeviceEventObjectEntry
SEQUENCE
	hh3cEponDeviceSampleMinimum	Integer32
	hh3cEponDeviceDyingGaspAlarmState	TruthValue
	hh3cEponDeviceDyingGaspAlarmEnabled	TruthValue
	hh3cEponDeviceCriticalEventState	TruthValue
	hh3cEponDeviceCriticalEventEnabled	TruthValue
	hh3cEponDeviceLocalLinkFaultAlarmState	TruthValue
	hh3cEponDeviceLocalLinkFaultAlarmEnabled	TruthValue
	hh3cEponDeviceTemperatureEventIndicationState	TruthValue
	hh3cEponDeviceTemperatureEventIndicationEnabled	TruthValue
	hh3cEponDevicePowerVoltageEventIndicationState	TruthValue
	hh3cEponDevicePowerVoltageEventIndicationEnabled	TruthValue
	hh3cEponDeviceGlobalEventState	TruthValue
	hh3cEponDeviceGlobalEventEnabled	TruthValue
	hh3cEponDeviceErroredSymbolPeriodEventState	TruthValue
	hh3cEponDeviceErroredSymbolPeriodEventEnabled	TruthValue
	hh3cEponDeviceErroredFrameEventState	TruthValue
	hh3cEponDeviceErroredFrameEventEnabled	TruthValue
	hh3cEponDeviceErroredFramePeriodEventState	TruthValue
	hh3cEponDeviceErroredFramePeriodEventEnabled	TruthValue
	hh3cEponDeviceErroredFrameSecondsSummaryEventState	TruthValue
	hh3cEponDeviceErroredFrameSecondsSummaryEventEnabled	TruthValue
	hh3cEponDeviceOrganizationSpecificEventState	TruthValue
	hh3cEponDeviceOrganizationSpecificEventEnabled	TruthValue
	hh3cEponDeviceEventControl	INTEGER

Hh3cEponDeviceEventsLogEntry
SEQUENCE
	hh3cEponDeviceEventsLogName	SnmpAdminString
	hh3cEponDeviceEventsLogIndex	Unsigned32
	hh3cEponDeviceEventsLogID	OBJECT IDENTIFIER
	hh3cEponDeviceEventsLogFirstTime	DateAndTime
	hh3cEponDeviceEventsLogLastTime	DateAndTime
	hh3cEponDeviceEventsLogCounts	Counter32
	hh3cEponDeviceEventsLogType	INTEGER
	hh3cEponDeviceEventsLogEntryStatus	RowStatus

Defined Values

hh3cEponDeviceMIB		1.3.6.1.4.1.25506.2.42.4
The objects in this MIB module are used to manage Ethernet Passive Optical Network (EPON) devices which are based on the Ethernet in the First Mile (EFM) PON as defined in IEEE Draft P802.3ah/D3.0 clause 60,64,65. This MIB is excerpted from the draft files directly,only changed the object name,added the hh3c as prefix. The following reference is used throughout this MIB module: [802.3ah] refers to: IEEE Draft P802.3ah/D3.3: 'Draft amendment to - Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications - Media Access Control Parameters, Physical Layers and Management Parameters for subscriber access networks', 22 April 2004. Of particular interest are Clause 64(MPCP) 65(P2mP RS) and 60 (PON PMDs). Clause 30, 'Management', and Clause 45,'Management Data Input/Output (MDIO) Interface'. Copyright (C) The Internet Society (2004). This version of this MIB module is part of XXXX see the RFC itself for full legal notices.
MODULE-IDENTITY

hh3cEponDeviceObjectMIB		1.3.6.1.4.1.25506.2.42.4.1
OBJECT IDENTIFIER

hh3cEponDeviceObjects		1.3.6.1.4.1.25506.2.42.4.1.1
OBJECT IDENTIFIER

hh3cEponDeviceConformance		1.3.6.1.4.1.25506.2.42.4.1.2
OBJECT IDENTIFIER

hh3cEponDeviceControlObjects		1.3.6.1.4.1.25506.2.42.4.1.1.1
OBJECT IDENTIFIER

hh3cEponDeviceStatObjects		1.3.6.1.4.1.25506.2.42.4.1.1.2
OBJECT IDENTIFIER

hh3cEponDeviceEventObjects		1.3.6.1.4.1.25506.2.42.4.1.1.3
OBJECT IDENTIFIER

hh3cEponDeviceControlTable		1.3.6.1.4.1.25506.2.42.4.1.1.1.1
Table for EPON device MIB modules.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponDeviceControlEntry

hh3cEponDeviceControlEntry		1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1
An entry in the EPON device Control table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponDeviceControlEntry

hh3cEponDeviceObjectReset		1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.1
This variable is used to reset the EPON device. The interface may be unavailable while the reset occurs and data may be lost. During reading operation it returns the state of the EPON device. running(1) indicates and operates normal operation, reset(2) indicates and operates reset mode. Writing can be done all the time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	running(1), reset(2)

hh3cEponDeviceObjectModes		1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.2
This variable defines the mode of the EPON device. When an olt(1) it is an Optical Line Terminal device (server) and when an onu(2) and Optical Network Unit device (client)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	olt(1), onu(2)

hh3cEponDeviceObjectFecEnabled		1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.4
This variable defines and provides information whether the EPON device uses FEC as defined in the [802.3ah] clause 65.2 for EPON. When noFECEnabled(1) the device does not support FEC mode When fecTxEnabled(2) the device supports the FEC transmission mode. When fecRxEnabled(3) the device supports the FEC Receive mode. When fecTxRxEnabled(4) the device supports the FEC transmission and receive mode. Writing can be done all the time. This attribute is relevant for an OLT and an ONU.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noFecEnabled(1), fecTxEnabled(2), fecRxEnabled(3), fecTxRxEnabled(4)

hh3cEponDeviceObjectOamMode		1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.5
This variable defines and provides information on the Operation Administration and Maintenance (OAM) mode of an EPON device as defined by the [802.3ah] clause 57. When noOam(1) the device does not supports the OAM mode. When oamServer(2) the device supports the OAM mode as a server unit. When oamClient(3) the device supports the OAM mode as a client unit. Writing can be done during initialization, hh3cEponDeviceObjectDeviceReadyMode is in notReady(1) or inProcess(2). This attribute is relevant for an OLT and an ONU.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noOam(1), oamServer(2), oamclient(3)

hh3cEponDeviceObjectDeviceReadyMode		1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.6
This variable defines the mode of an EPON device and provides information on the mode in initialization - ready for registration as defined by the [802.3ah] clause 64. When notReady(1) the device is not ready for operation. When inProcess(2) the device is in initialization process. When ready(3) the device is ready for registration. Writing can be done all the time. This attribute is relevant for an OLT and an ONU.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notReady(1), inProcess(2), ready(3)

hh3cEponDeviceObjectPowerDown		1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.7
Setting this variable to True(1) will cause Device to be entered into Power down mode where no registration is allowed and only receiving data from the link. Writing can be done all the time. This attribute is relevant for an OLT and an ONU.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponDeviceObjectNumberOfLLIDs		1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.8
A read only variable which defines the number of registered LLIDs (as defined by the [802.3ah] clause 65) in a EPON network for an OLT and an ONU. Initialization value is 0. This attribute is relevant for an OLT and an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponDeviceObjectReportThreshold		1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.9
A set of 8 integers, for each LLID, that defines the threshold reporting for each Queue in the REPORT message, as defined in [802.3ah] 64. First Queue set reporting will provide information on the queue occupancy of frames below this Threshold. The value returned shall be in Time quanta (TQ) which is 16nsec or 2 octets increments. Writing can be done all the time. This attribute is relevant for an OLT and an ONU.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hh3cEponDeviceRemoteMACAddressLLIDControl		1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.10
Indicates and controls the resetting of the LLID MAC address log. Setting this object to none(1) has no action resetLog(2) empties the LLID MAC address log. All data is deleted. Setting it to useDefaultReporting(3) returns all entries priorities to their factory-default reporting. Reading this object always returns useDefaultReporting(3).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), resetLog(2), useDefaultReporting(3)

hh3cEponDeviceRemoteMACAddressLLIDTable		1.3.6.1.4.1.25506.2.42.4.1.1.1.2
A table of read-only value that identifies the source_address and LLIDs parameter of the remote devices in the network. This MacAddress value, as defined in [802.3ah], 30.3.5.1.5, is updated on reception of a valid frame with a unicast destination Field or (1) a destination Field equal to the reserved multicast address for MAC Control specified in [802.3ah] Annex 31A, (2) lengthOrType field value equal to the reserved Type for MAC Control as specified in [802.3ah] Annex 31A. (3)an MPCP subtype value equal to the subtype reserved for MPCP as specified in [802.3ah] Annex 31A, and an LLID as allocated by the OLT. The table is defined as Remote MAC address - LLID (RMadL) The table is relevant only for an OLT device, and is equivalent from a bridge emulation to the bridge port-MAC address table where the LLIDs are equivalent to virtual bridge ports.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponDeviceRemoteMACAddressLLIDEntry

hh3cEponDeviceRemoteMACAddressLLIDEntry		1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1
A group of entries. Applications create and delete entries using hh3cEponDeviceRMadlEntryStatus. When adding objects to an LLID they are added in the persistent order of their index in this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponDeviceRemoteMACAddressLLIDEntry

hh3cEponDeviceRemoteMACAddressLLIDName		1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1.1
A locally-unique, administratively assigned name for a group of entries.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(1..32)

hh3cEponDeviceRMadlLLID		1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1.2
An arbitrary integer for the purpose of identifying the LLID. Writing can be done all the time.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..4294967295

hh3cEponDeviceRMadlLogID		1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1.3
The object identifier of a MIB module object to add to an entry, indicating the entry ID in the table. Writing can be done all the time.
Status: current	Access: read-create
OBJECT-TYPE
	OBJECT IDENTIFIER

hh3cEponDeviceRMadlRemoteAddress		1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1.4
The remote MAC address of the LLID. Writing can be done all the time.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

hh3cEponDeviceRMadlType		1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1.5
A list of types for entries - LLIDs. Indicates and defines the state of registration. notRegister(1) marks a non registered LID, registered(2) marks a registered LLID. Writing can be done all the time.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notRegister(1), registered(2)

hh3cEponDeviceRMadlAction		1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1.6
A list of actions for an entry - LLID. Indicates and defines the state of registration for the remote device. none(1) marks no action, register(2) marks to register an LLID, deregister(3) marks to deregister an LLID, reregister(4) marks reregistered LLID. Writing can be done all the time.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(1), register(2), deregister(3), reregister(4)

hh3cEponDeviceRMadlEntryStatus		1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1.7
The control that allows creation and deletion of entries. Once made active an entry MAY not be modified except to delete it.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hh3cEponDeviceStatTable		1.3.6.1.4.1.25506.2.42.4.1.1.2.1
This table defines the list of statistics counters of EPON devices. The attributes are relevant for an OLT and an ONU.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponDeviceStatEntry

hh3cEponDeviceStatEntry		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1
Table entries for Table of statistics counters of EPON devices.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponDeviceStatEntry

hh3cEponDeviceStatTxFramesQueue0		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.1
A count of the number of times a -Queue-0- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-0-. The -Queue-0- marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatTxFramesQueue1		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.2
A count of the number of times a -Queue-1- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-1-. The -Queue-1- marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatTxFramesQueue2		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.3
A count of the number of times a -Queue-2- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-2-. The -Queue-2- marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatTxFramesQueue3		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.4
A count of the number of times a -Queue-3- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-3-. The -Queue-3- marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatTxFramesQueue4		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.5
A count of the number of times a -Queue-4- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-4-. The -Queue-4- marking matched the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatTxFramesQueue5		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.6
A count of the number of times a -Queue-5- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-5-. The -Queue-5- marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatTxFramesQueue6		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.7
A count of the number of times a -Queue-6- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-6-. The -Queue-6- marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatTxFramesQueue7		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.8
A count of the number of times a -Queue-7- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-7-. The -Queue-7- marking matched the REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatRxFramesQueue0		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.9
A count of the number of times a -Queue-0- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-0-. The -Queue-0- marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatRxFramesQueue1		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.10
A count of the number of times a -Queue-1- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-1-. The -Queue-1- marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatRxFramesQueue2		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.11
A count of the number of times a -Queue-2- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-2-. The -Queue-2- marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatRxFramesQueue3		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.12
A count of the number of times a -Queue-3- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-3-. The -Queue-3- marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatRxFramesQueue4		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.13
A count of the number of times a -Queue-4- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-4-. The -Queue-4- marking matched the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatRxFramesQueue5		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.14
A count of the number of times a -Queue-5- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-5-. The -Queue-5- marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatRxFramesQueue6		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.15
A count of the number of times a -Queue-6- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-6-. The -Queue-6- marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatRxFramesQueue7		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.16
A count of the number of times a -Queue-7- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-7-. The -Queue-7- marking matched the REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatDroppedFramesQueue0		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.17
A count of the number of times a -Queue-0- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-0-. The -Queue-0- marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatDroppedFramesQueue1		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.18
A count of the number of times a -Queue-1- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-1-. The -Queue-1- marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatDroppedFramesQueue2		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.19
A count of the number of times a -Queue-2- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-2-. The -Queue-2- marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatDroppedFramesQueue3		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.20
A count of the number of times a -Queue-3- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-3-. The -Queue-3- marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatDroppedFramesQueue4		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.21
A count of the number of times a -Queue-4- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-4-. The -Queue-4- marking matched the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatDroppedFramesQueue5		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.22
A count of the number of times a -Queue-5- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-5-. The -Queue-5- marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatDroppedFramesQueue6		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.23
A count of the number of times a -Queue-6- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-6-. The -Queue-6- marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceStatDroppedFramesQueue7		1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.24
A count of the number of times a -Queue-7- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-7-. The -Queue-7- marking matched the REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceEventObjectTable		1.3.6.1.4.1.25506.2.42.4.1.1.3.1
This table defines the Event Objects for EPON devices. The attributes are relevant for an OLT and an ONU.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponDeviceEventObjectEntry

hh3cEponDeviceEventObjectEntry		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1
Table entries for Table of Event objects for EPON devices.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponDeviceEventObjectEntry

hh3cEponDeviceSampleMinimum		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.1
The minimum Frequency of events this system will accept. A system may use the larger values of this minimum to lessen the impact of constant sampling. For larger sampling intervals the system samples less often and suffers less overhead. Unless explicitly resource limited, a system's value for this object SHOULD be 1, allowing as small as a 1 second interval for ongoing trigger sampling. Writing of the value can be done all the time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..2147483647

hh3cEponDeviceDyingGaspAlarmState		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.2
A read-only variable, which defines the state of the Dying Gasp indication of the OAM alarm indications as described in the [802.3ah] clause 57. When true the device has a dying gasp alarm asserted. When false the dying gasp alarm is reset
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

hh3cEponDeviceDyingGaspAlarmEnabled		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.3
A control to allow DyingGaspAlarm event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponDeviceCriticalEventState		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.4
A read-only variable, which defines the state of the Critical Event indication of the OAM alarm indications as described in the [802.3ah] clause 57. When true the device has a Critical Event asserted. When false the Critical Event is reset.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

hh3cEponDeviceCriticalEventEnabled		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.5
A control to allow CriticalEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponDeviceLocalLinkFaultAlarmState		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.6
A read-only variable, which defines the state of the Local Link Fault indication of the OAM alarm indications as described in the [802.3ah] clause 57. When true the device has a Local Link Fault alarm asserted. When false the Local Link Fault alarm is reset.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

hh3cEponDeviceLocalLinkFaultAlarmEnabled		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.7
A control to allow LocalLinkFaultAlarm event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponDeviceTemperatureEventIndicationState		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.8
A read-only variable, which defines the state of the Temperature Event indication of an EPON device. When condition of box temperature is above the threshold defined the alarm is asserted. When the condition is below that threshold the alarm is de-asserted. When true the device has a Temperature Event Indication asserted. When false the Temperature Event Indication is reset.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

hh3cEponDeviceTemperatureEventIndicationEnabled		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.9
A control to allow TemperatureEventIndication event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponDevicePowerVoltageEventIndicationState		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.10
A read-only variable, which defines the state of the Power/Voltage Event Indication of an EPON device. When condition of box Power/voltage is above the threshold defined the alarm is asserted. When the condition is below that threshold the alarm is de-asserted. When true the device has a Power/Voltage Event Indication asserted. When false the Power/Voltage Event Indication is reset.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

hh3cEponDevicePowerVoltageEventIndicationEnabled		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.11
A control to allow PowerVoltageEventIndication event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponDeviceGlobalEventState		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.12
A read-only variable, which defines the state of the Global Event indication of an EPON device. When the indication of the event input occurs the event is asserted. When the input is removed that event is de-asserted. When true the device has a Global Event asserted. When false the Global Event Indication is reset.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

hh3cEponDeviceGlobalEventEnabled		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.13
A control to allow GlobalEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponDeviceErroredSymbolPeriodEventState		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.14
A read-only variable, which defines the state of the Errored Symbol Period Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Symbol Period Event asserted. When false the Errored Symbol Period Event is reset.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

hh3cEponDeviceErroredSymbolPeriodEventEnabled		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.15
A control to allow ErroredSymbolPeriodEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponDeviceErroredFrameEventState		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.16
A read-only variable, which defines the state of the Errored Frame Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Frame Event asserted. When false the Errored Frame Event is reset.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

hh3cEponDeviceErroredFrameEventEnabled		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.17
A control to allow ErroredFrameEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponDeviceErroredFramePeriodEventState		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.18
A read-only variable, which defines the state of the Errored Frame Period Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Frame Period Event asserted. When false the Errored Frame Period Event is reset.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

hh3cEponDeviceErroredFramePeriodEventEnabled		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.19
A control to allow ErroredFramePeriodEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponDeviceErroredFrameSecondsSummaryEventState		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.20
A read-only variable, which defines the state of the Errored Frame Seconds Summary Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Frame Seconds Summary Event asserted. When false the Errored Frame Seconds Summary Event is reset.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

hh3cEponDeviceErroredFrameSecondsSummaryEventEnabled		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.21
A control to allow ErroredFrameSecondsSummaryEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponDeviceOrganizationSpecificEventState		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.22
A read-only variable, which defines the state of the Organization Specific Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Organization Specific Event asserted. When false the Organization Specific Event is reset.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

hh3cEponDeviceOrganizationSpecificEventEnabled		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.23
A control to allow OrganizationSpecificEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponDeviceEventControl		1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.24
Indicates and controls the resetting of the Event log. Setting this object to none(1) has no action resetLog(2) empties the event log. All data is deleted. Setting it to useDefaultReporting(3) returns all event priorities to their factory-default reporting. Reading this object always returns useDefaultReporting(3).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), resetLog(2), useDefaultReporting(3)

hh3cEponDeviceEventsLogTable		1.3.6.1.4.1.25506.2.42.4.1.1.3.2
A table of objects provides a log of notification based on the event as pointed to by entries in those tables. The intent is a MAC level event log (set of events to when they happened). This attribute is relevant for an OLT and an ONU.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponDeviceEventsLogEntry

hh3cEponDeviceEventsLogEntry		1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1
A group of Events. Applications create and delete entries using hh3cEponDeviceEventsEntryStatus. When adding objects to a notification they are added in the lexical order of their index in this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponDeviceEventsLogEntry

hh3cEponDeviceEventsLogName		1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.1
A locally-unique, administratively assigned name for a group of Events.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(1..32)

hh3cEponDeviceEventsLogIndex		1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.2
An arbitrary integer for the purpose of identifying individual Events within a hh3cEponDeviceEventsLogName group. Events within a group are placed in the notification in the numerical order of this index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..4294967295

hh3cEponDeviceEventsLogID		1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.3
The object identifier of a MIB module object to add to a Notification that results from the event. Writing can be done all the time.
Status: current	Access: read-create
OBJECT-TYPE
	OBJECT IDENTIFIER

hh3cEponDeviceEventsLogFirstTime		1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.4
The time that an entry was created.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hh3cEponDeviceEventsLogLastTime		1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.5
If multiple events are reported via the same entry, the time that the last event for this entry occurred, otherwise this should have the same value as hh3cEponDeviceEventsLogFirstTime.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hh3cEponDeviceEventsLogCounts		1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.6
The number of consecutive event instances reported by this entry. This starts at 1 with the creation of this row and increments by 1 for each subsequent duplicate event.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cEponDeviceEventsLogType		1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.7
A list of types for Events. Events are ordered according to their significance where 1 is the highest severity. hh3cEponDeviceDyingGaspAlarmState(1) indicates a Dying Gasp Alarm State, hh3cEponDeviceCriticalEventState(2) indicates a Critical Event State, hh3cEponDeviceLocalLinkFaultAlarmState(3) indicates a Local Link Fault Alarm State, hh3cEponDeviceTemperatureEventIndicationState(4) indicates a Temperature Event Indication State, hh3cEponDevicePowerVoltageEventIndicationState(5) indicates a Power Voltage Event Indication State, hh3cEponDeviceGlobalEventState(6) indicates a Global Event State, hh3cEponDeviceErroredSymbolPeriodEventState(7) indicates an Errored Symbol Period Event State, hh3cEponDeviceErroredFrameEventState(8) indicates an Errored Frame Event State, hh3cEponDeviceErroredFramePeriodEventState(9) indicates an Errored Frame Period Event State, hh3cEponDeviceErroredFrameSecondsSummaryEventState(10) indicates an Errored Frame Seconds Summary Event State, hh3cEponDeviceOrganizationSpecificEventState(11) indicates an Organization Specific Event State.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	hh3cEponDeviceDyingGaspAlarmState(1), hh3cEponDeviceCriticalEventState(2), hh3cEponDeviceLocalLinkFaultAlarmState(3), hh3cEponDeviceTemperatureEventIndicationState(4), hh3cEponDevicePowerVoltageEventIndicationState(5), hh3cEponDeviceGlobalEventState(6), hh3cEponDeviceErroredSymbolPeriodEventState(7), hh3cEponDeviceErroredFrameEventState(8), hh3cEponDeviceErroredFramePeriodEventState(9), hh3cEponDeviceErroredFrameSecondsSummaryEventState(10), hh3cEponDeviceOrganizationSpecificEventState(11)

hh3cEponDeviceEventsLogEntryStatus		1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.8
The control that allows creation and deletion of entries. Once made active an entry MAY not be modified except to delete it.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hh3cEponDeviceGroups		1.3.6.1.4.1.25506.2.42.4.1.2.1
OBJECT IDENTIFIER

hh3cEponDeviceGroupControl		1.3.6.1.4.1.25506.2.42.4.1.2.1.1
A collection of objects of hh3cEponDevice control definition.
Status: current	Access: read-create
OBJECT-GROUP

hh3cEponDeviceGroupRMadLTable		1.3.6.1.4.1.25506.2.42.4.1.2.1.2
A collection of objects of hh3cEponDevice remote Mac address to LLID table.
Status: current	Access: read-create
OBJECT-GROUP

hh3cEponDeviceGroupStat		1.3.6.1.4.1.25506.2.42.4.1.2.1.3
A collection of objects of EPON device Statistics
Status: current	Access: read-create
OBJECT-GROUP

hh3cEponDeviceGroupEvent		1.3.6.1.4.1.25506.2.42.4.1.2.1.4
A collection of objects for EPON device Events
Status: current	Access: read-create
OBJECT-GROUP

hh3cEponDeviceGroupEventLog		1.3.6.1.4.1.25506.2.42.4.1.2.1.5
A collection of objects for EPON device Events log
Status: current	Access: read-create
OBJECT-GROUP

hh3cEponDeviceCompliances		1.3.6.1.4.1.25506.2.42.4.1.2.2
OBJECT IDENTIFIER

hh3cEponDeviceCompliance		1.3.6.1.4.1.25506.2.42.4.1.2.2.1
The compliance statement for EPON Devices.
Status: current	Access: read-create
MODULE-COMPLIANCE