HH3C-EPON-UNI-MIB

File: HH3C-EPON-UNI-MIB.mib (65973 bytes)

Imported modules

HH3C-OID-MIB	IF-MIB	SNMPv2-SMI
SNMPv2-TC

Imported symbols

hh3cEpon	ifIndex	ifDescr
Integer32	Unsigned32	IpAddress
OBJECT-TYPE	MODULE-IDENTITY	NOTIFICATION-TYPE
MacAddress	TruthValue	RowStatus

Defined Types

Hh3cEponUniSysManEntry
SEQUENCE
	hh3cEponUniIndex	Integer32
	hh3cEponUniDescr	OCTET STRING
	hh3cEponUniAdminStatus	INTEGER
	hh3cEponUniMdi	INTEGER
	hh3cEponUniPriority	Integer32
	hh3cEponUniVlanType	INTEGER
	hh3cEponUniAccessVlan	Integer32
	hh3cEponUniTrunkPvid	INTEGER
	hh3cEponUniVLANTrunkAllowListLow	OCTET STRING
	hh3cEponUniVLANTrunkAllowListHigh	OCTET STRING
	hh3cEponUniInboundLineRate	Integer32
	hh3cEponUniOutboundLineRate	Integer32
	hh3cEponUniFlowControl	TruthValue
	hh3cEponUniSpeed	INTEGER
	hh3cEponUniDuplex	INTEGER
	hh3cEponUniVlanVPNStatus	TruthValue
	hh3cEponUniCountReset	INTEGER
	hh3cEponUniPortIsolate	INTEGER
	hh3cEponUniVlanConfiguration	OCTET STRING
	hh3cEponUniAutoNegotiation	INTEGER
	hh3cEponUniRestartAutoNeg	INTEGER
	hh3cEponUniLinkStatus	INTEGER
	hh3cEponUniInterfaceType	INTEGER
	hh3cEponUniVitualCableTest	INTEGER
	hh3cEponUniVCTCableStatus	INTEGER
	hh3cEponUniVCTCableLength	Integer32
	hh3cEponUniVCTImpedanceMismatch	INTEGER
	hh3cEponUniVCTPairSkew	Integer32
	hh3cEponUniVCTPairSwap	INTEGER
	hh3cEponUniVCTPolaritySwap	INTEGER
	hh3cEponUniVCTInsertionLoss	Integer32
	hh3cEponUniVCTReturnLoss	Integer32
	hh3cEponUniVCTNearendCrosstalk	Integer32
	hh3cEponUniVlan	Integer32

Hh3cEponUniCountEntry
SEQUENCE
	hh3cEponUniInStatsPkts	Unsigned32
	hh3cEponUniInStatsUnicastPkts	Unsigned32
	hh3cEponUniInStatsBroadcastPkts	Unsigned32
	hh3cEponUniInStatsMulticastPkts	Unsigned32
	hh3cEponUniInPausePkts	Unsigned32
	hh3cEponUniInTotalErrors	Unsigned32
	hh3cEponUniInStatsCRCAlignErrors	Unsigned32
	hh3cEponUniInStatsUndersizePkts	Unsigned32
	hh3cEponUniInStatsOversizePkts	Unsigned32
	hh3cEponUniInErrorbyOther	Unsigned32
	hh3cEponUniOutStatsPkts	Unsigned32
	hh3cEponUniOutStatsUnicastPkts	Unsigned32
	hh3cEponUniOutStatsBroadcastPkts	Unsigned32
	hh3cEponUniOutStatsMulticastPkts	Unsigned32
	hh3cEponUniOutStatsPausePkts	Unsigned32
	hh3cEponUniOutTotalErrors	Unsigned32
	hh3cEponUniOutStatsCollisions	Unsigned32
	hh3cEponUniOutDelayExceededDiscards	Unsigned32
	hh3cEponUniOutErrorbyOther	Unsigned32
	hh3cEponUniOutDroppedFrames	Unsigned32

Hh3cEponUniIgmpInfoEntry
SEQUENCE
	hh3cEponUniMacIndex	Integer32
	hh3cEponUniIgmpMacAddress	MacAddress
	hh3cEponUniIgmpVlanId	Integer32

Hh3cEponUniPortPolicyEntry
SEQUENCE
	hh3cEponUniPortPolicyStatus	INTEGER
	hh3cEponUniPortPolicyCir	Integer32
	hh3cEponUniPortPolicyBucketDepth	Integer32
	hh3cEponUniPortPolicyExtraBurst	Integer32
	hh3cEponUniPortPolicyInboundCir	Integer32
	hh3cEponUniPortPolicyInboundBucketDepth	Integer32
	hh3cEponUniPortPolicyInboundExtraBurst	Integer32
	hh3cEponUniPortPolicyOutboundCir	Integer32
	hh3cEponUniPortPolicyOutboundPir	Integer32

Hh3cEponUniMulticastEntry
SEQUENCE
	hh3cEponUniMulticastGroupNumber	Integer32
	hh3cEponUniMulticastVlanList	OCTET STRING
	hh3cEponUniMulticastStripStatus	INTEGER
	hh3cEponUniMulticastFastleave	TruthValue

Hh3cEponUniTechAbilityEntry
SEQUENCE
	hh3cEponUniLocalTechAbility	OCTET STRING
	hh3cEponUniAdvertisedTechAbility	OCTET STRING

Hh3cEponUniMulticastControlEntry
SEQUENCE
	hh3cEponUniMulticastVlanIndex	Integer32
	hh3cEponUniMulticastAddressList	OCTET STRING
	hh3cEponUniMulticastAccessRule	INTEGER
	hh3cEponUniMulticastChannelLimit	Integer32
	hh3cEponUniMulticastPreTimeSlice	Integer32
	hh3cEponUniMulticastPreTimes	Integer32
	hh3cEponUniMulticastPreInterval	Integer32
	hh3cEponUniMulticastRowStatus	RowStatus
	hh3cEponUniMulticastIndex	INTEGER
	hh3cEponUniMulticastSourceIpList	OCTET STRING
	hh3cEponUniMulticastResetInterval	Integer32

Hh3cEponUniQosIndexNextEntry
SEQUENCE
	hh3cEponUniQosConfIndexNext	Integer32

Hh3cEponUniQosConfEntry
SEQUENCE
	hh3cEponUniQosConfIndex	Integer32
	hh3cEponUniQosConfRuleIndexNext	Integer32
	hh3cEponUniQosConfMappedQueue	Integer32
	hh3cEponUniQosConfMarkedPriority	Integer32
	hh3cEponUniQosConfRowStatus	RowStatus

Hh3cEponUniQosRuleEntry
SEQUENCE
	hh3cEponUniQosRuleIndex	Integer32
	hh3cEponUniQosRuleSelector	INTEGER
	hh3cEponUniQosRuleValue	Integer32
	hh3cEponUniQosRuleMacAddress	MacAddress
	hh3cEponUniQosRuleOperator	INTEGER
	hh3cEponUniQosRuleRowStatus	RowStatus

Hh3cEponUniMirrorGroupEntry
SEQUENCE
	hh3cEponUniMirrorGroupID	Integer32
	hh3cEponUniMirrorInboundPortList	OCTET STRING
	hh3cEponUniMirrorOutboundPortList	OCTET STRING
	hh3cEponUniMonitorPort	Integer32
	hh3cEponUniMirrorRowStatus	RowStatus

Hh3cEponUniMirrorGroupIdNextEntry
SEQUENCE
	hh3cEponUniMirrorGroupIDNext	Integer32

Hh3cEponUniMulticastCtrlInfoEntry
SEQUENCE
	hh3cEponUniMultActVlan	Integer32
	hh3cEponUniMultActAddress	IpAddress
	hh3cEponUniMultActAccessRule	INTEGER
	hh3cEponUniMultActPreTimes	Integer32
	hh3cEponUniMultActPreRemain	Integer32

Hh3cEponUniMulticastIndexNextEntry
SEQUENCE
	hh3cEponUniMulticastConfIndexNext	Integer32

Defined Values

hh3cEponUni		1.3.6.1.4.1.25506.2.42.5
The objects in this MIB module are used to manage and display current configuration of UNI (user network interface) which is based on the ONU(Optical Network Unit).
MODULE-IDENTITY

hh3cEponUniSysMan		1.3.6.1.4.1.25506.2.42.5.1
OBJECT IDENTIFIER

hh3cEponUniSysManTable		1.3.6.1.4.1.25506.2.42.5.1.1
This table defines several UNI system parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponUniSysManEntry

hh3cEponUniSysManEntry		1.3.6.1.4.1.25506.2.42.5.1.1.1
The entry of hh3cEponUniSysManTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponUniSysManEntry

hh3cEponUniIndex		1.3.6.1.4.1.25506.2.42.5.1.1.1.1
The index value which uniquely identifies the FE(fast Ethernet) interface of the ONU.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hh3cEponUniDescr		1.3.6.1.4.1.25506.2.42.5.1.1.1.2
A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware and software.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

hh3cEponUniAdminStatus		1.3.6.1.4.1.25506.2.42.5.1.1.1.3
The desired state of the user network interface. When a managed system initializes, all user network interfaces start with down(2) state. The testing(3)state indicates that no operational packets can be passed. As a result of either explicit management action or per configuration information retained by the managed system, hh3cEponUniAdminStatus is then changed to either the up(1) or testing(3) states (or remains in the down(2) state).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3)

hh3cEponUniMdi		1.3.6.1.4.1.25506.2.42.5.1.1.1.4
Type of the line connected to UNI interface: mdi-ii(straight-through cable), mdi-x (crossover cable), mdi-auto (auto-sensing).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	mdi-ii(1), mdi-x(2), mdi-auto(3)

hh3cEponUniPriority		1.3.6.1.4.1.25506.2.42.5.1.1.1.5
The priority of user network interface. If the value is larger, the priority will be higher.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..7

hh3cEponUniVlanType		1.3.6.1.4.1.25506.2.42.5.1.1.1.6
UNI vlan types.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	vlantrunk(1), access(2), hybrid(3), untagged(4), transparent(5), doubletagged(6), tag(7), translation(8)

hh3cEponUniAccessVlan		1.3.6.1.4.1.25506.2.42.5.1.1.1.7
The vlan ID assigned to untagged frames or Priority-Tagged frames received on user network interface.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

hh3cEponUniTrunkPvid		1.3.6.1.4.1.25506.2.42.5.1.1.1.8
PVID(port vlan ID), the vlan ID assigned to untagged frames or Priority-Tagged frames received on user network interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..4094

hh3cEponUniVLANTrunkAllowListLow		1.3.6.1.4.1.25506.2.42.5.1.1.1.9
Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 1 through 8, the second octet specifying vlans 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each allowed vlan of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is allowed in the set of vlans. the vlan is not allowed if its bit has a value of '0'.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

hh3cEponUniVLANTrunkAllowListHigh		1.3.6.1.4.1.25506.2.42.5.1.1.1.10
Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 2049 through 2056, the second octet specifying vlans 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered vlan, and the least significant bit represents the lowest numbered vlan. Thus, each allowed vlan of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is allowed in the set of vlans; the vlan is not allowed if its bit has a value of '0'.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

hh3cEponUniInboundLineRate		1.3.6.1.4.1.25506.2.42.5.1.1.1.11
The value of the inbound line-rate. measured with kbps. The upper limit of the line-rate is the value of hh3cEponUniLineRateMax in the entry. It must be multiple of the value of hh3cEponUniLineRateStep. The default value of hh3cEponUniLineRate is the value of hh3cEponUniLineRateMax.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hh3cEponUniOutboundLineRate		1.3.6.1.4.1.25506.2.42.5.1.1.1.12
The value of the outbound line-rate. measured with kbps. The upper limit of the line-rate is the value of hh3cEponUniLineRateMax in the entry. It must be multiple of the value of hh3cEponUniLineRateStep. The default value of hh3cEponUniLineRate is the value of hh3cEponUniLineRateMax.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hh3cEponUniFlowControl		1.3.6.1.4.1.25506.2.42.5.1.1.1.13
Flow control status. true(1) - Flow control status enable. false(2) - Flow control status disable.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponUniSpeed		1.3.6.1.4.1.25506.2.42.5.1.1.1.14
User network interface speed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(0), s10M(10), s100M(100), s1000M(1000), s10000M(10000), s24000M(24000)

hh3cEponUniDuplex		1.3.6.1.4.1.25506.2.42.5.1.1.1.15
User network interface mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), half(2), auto(3)

hh3cEponUniVlanVPNStatus		1.3.6.1.4.1.25506.2.42.5.1.1.1.16
vlan VPN status. true(1) - vlan VPN status enable. false(2) - vlan VPN disable.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponUniCountReset		1.3.6.1.4.1.25506.2.42.5.1.1.1.17
Reset the counter which is about packets of the interface, then the counter will change to zero. There is no sense in reading this object.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

hh3cEponUniPortIsolate		1.3.6.1.4.1.25506.2.42.5.1.1.1.18
enable - enable UNI port isolate setting. disable - disable UNI port isolate setting.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

hh3cEponUniVlanConfiguration		1.3.6.1.4.1.25506.2.42.5.1.1.1.23
The vlan configuration of the related vlan mode. Transparent vlan mode: hh3cEponUniVlanConfiguration is a zero length string. Tag vlan mode: the first four octets were the tag assigned to untagged frames received on UNI, including TPID, VID,CFI and priority. Translation vlan mode: the first four octets were the old tag (including TPID, VID, CFI and priority), which is replaced by the new tag(including TPID, VID, CFI and priority), the second four octets.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..255)

hh3cEponUniAutoNegotiation		1.3.6.1.4.1.25506.2.42.5.1.1.1.25
enable - enable auto negotiation. disable - disable auto negotiation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

hh3cEponUniRestartAutoNeg		1.3.6.1.4.1.25506.2.42.5.1.1.1.26
Force to restart the auto negotiation process.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	autoNegotiation(1)

hh3cEponUniLinkStatus		1.3.6.1.4.1.25506.2.42.5.1.1.1.29
The link status of UNI.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

hh3cEponUniInterfaceType		1.3.6.1.4.1.25506.2.42.5.1.1.1.30
UNI interface type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	gigabitethernetport(1), fastethernetport(2), voipport(3), e1port(4)

hh3cEponUniVitualCableTest		1.3.6.1.4.1.25506.2.42.5.1.1.1.31
True(1): Virtual cable test enable. False(2): Virtual cable test disable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	true(1), false(2)

hh3cEponUniVCTCableStatus		1.3.6.1.4.1.25506.2.42.5.1.1.1.32
Get the cable status. Normal(1),cable is normal. Abnormal(2),cable is abnormal. AbnormalOpen(3),cable is abnormal because of open circuit. AbnormalShort(4),cable is abnormal because of short circuit. Failure(5),cable is abnormal because of testing failure.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), abnormal(2), abnormalOpen(3), abnormalShort(4), failure(5)

hh3cEponUniVCTCableLength		1.3.6.1.4.1.25506.2.42.5.1.1.1.33
Get the cable length. When hh3cEponUniVCTCableStatus is normal, the node stands for the length from the UNI port to the port opposite. When hh3cEponUniVCTCableStatus is abnormal, it stands for the lengh from the UNI port to the failure place. Unit:meter(m).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponUniVCTImpedanceMismatch		1.3.6.1.4.1.25506.2.42.5.1.1.1.34
Get the cable impedance. Not-support(1),the UNI port does not support this function. True(2),impedance match. False(3),impedance mismatch.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	not-support(1), true(2), false(3)

hh3cEponUniVCTPairSkew		1.3.6.1.4.1.25506.2.42.5.1.1.1.35
Get the symmetry of cable. If the function is not supported, the default value 0 will be returned. Unit:nanosecond(ns).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponUniVCTPairSwap		1.3.6.1.4.1.25506.2.42.5.1.1.1.36
NotSupport(1),the UNI port does not support this function. True(2),pair swap. False(3),not pair swap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSupport(1), true(2), false(3)

hh3cEponUniVCTPolaritySwap		1.3.6.1.4.1.25506.2.42.5.1.1.1.37
NotSupport(1),the UNI port does not support this function. True(2),polarity swap. False(3),not polarity swap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSupport(1), true(2), false(3)

hh3cEponUniVCTInsertionLoss		1.3.6.1.4.1.25506.2.42.5.1.1.1.38
If the function is not supported, the default value 0 will be returned. Unit:decibel(db).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponUniVCTReturnLoss		1.3.6.1.4.1.25506.2.42.5.1.1.1.39
If the function is not supported, the default value 0 will be returned. Unit:decibel(db).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponUniVCTNearendCrosstalk		1.3.6.1.4.1.25506.2.42.5.1.1.1.40
If the function is not supported, the default value 0 will be returned. Unit:decibel(db).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponUniVlan		1.3.6.1.4.1.25506.2.42.5.1.1.1.41
If the function is not supported, the default value 0 will be returned. Unit:decibel(db).
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hh3cEponUniCountTable		1.3.6.1.4.1.25506.2.42.5.1.2
A list of interface counter about frames entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponUniCountEntry

hh3cEponUniCountEntry		1.3.6.1.4.1.25506.2.42.5.1.2.1
An entry containing management information applicable to a particular interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponUniCountEntry

hh3cEponUniInStatsPkts		1.3.6.1.4.1.25506.2.42.5.1.2.1.1
The total number of frames (including bad frames, broadcast frames, and multicast frames) received.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniInStatsUnicastPkts		1.3.6.1.4.1.25506.2.42.5.1.2.1.2
The total number of good frames received that are directed to the unicast address. Note that this does not include multicast and broadcast frames.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniInStatsBroadcastPkts		1.3.6.1.4.1.25506.2.42.5.1.2.1.3
The total number of good frames received that are directed to the broadcast address. Note that this does not include multicast frames.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniInStatsMulticastPkts		1.3.6.1.4.1.25506.2.42.5.1.2.1.4
The total number of good frames received that are directed to a multicast address. Note that this number does not include frames directed to the broadcast address.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniInPausePkts		1.3.6.1.4.1.25506.2.42.5.1.2.1.5
A count of MAC Control frames received on this interface by the pause(flow control) operation. This counter does not increment when the interface is in a half-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniInTotalErrors		1.3.6.1.4.1.25506.2.42.5.1.2.1.6
Total count of the error frames received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniInStatsCRCAlignErrors		1.3.6.1.4.1.25506.2.42.5.1.2.1.7
The total number of frames received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniInStatsUndersizePkts		1.3.6.1.4.1.25506.2.42.5.1.2.1.8
The total number of frames received that are less than 64 octets long (excluding framing bits, but including FCS octets) and are otherwise well formed.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniInStatsOversizePkts		1.3.6.1.4.1.25506.2.42.5.1.2.1.9
The total number of frames received that are longer than 1518 octets (excluding framing bits, but including FCS octets) and are otherwise well formed.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniInErrorbyOther		1.3.6.1.4.1.25506.2.42.5.1.2.1.10
The total number of error frames received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniOutStatsPkts		1.3.6.1.4.1.25506.2.42.5.1.2.1.11
The total number of frames (including bad frames, broadcast frames, and multicast frames) sent.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniOutStatsUnicastPkts		1.3.6.1.4.1.25506.2.42.5.1.2.1.12
The total number of good frames sent that are directed to the unicast address. Note that this does not include multicast and broadcast frames.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniOutStatsBroadcastPkts		1.3.6.1.4.1.25506.2.42.5.1.2.1.13
The total number of good frames sent that are directed to the broadcast address. Note that this does not include multicast frames.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniOutStatsMulticastPkts		1.3.6.1.4.1.25506.2.42.5.1.2.1.14
The total number of good frames sent that are directed to a multicast address. Note that this number does not include frames directed to the broadcast address.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniOutStatsPausePkts		1.3.6.1.4.1.25506.2.42.5.1.2.1.15
The total number of MAC control frames sent on this interface by the pause operation. This counter does not increment when the interface is in a half-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniOutTotalErrors		1.3.6.1.4.1.25506.2.42.5.1.2.1.16
The total number of error frames sent on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniOutStatsCollisions		1.3.6.1.4.1.25506.2.42.5.1.2.1.17
The best estimate of the total number of collisions on this Ethernet segment. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) of IEEE standard 802.3 states that a station must detect a collision, in the receive mode, if three or more stations are transmitting simultaneously. A repeater port must detect a collision when two or more stations are transmitting simultaneously. Thus a probe placed on a repeater port could record more collisions than a probe connected to a station on the same segment could. Probe location plays a much smaller role when considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE standard 802.3 defines a collision as the simultaneous presence of signals on the DO and RD circuits (transmitting and receiving at the same time). A 10BASE-T station can only detect collisions when it is transmitting. Thus probes placed on a station and a repeater, should report the same number of collisions. Note also that an RMON probe inside a repeater should ideally report collisions between the repeater and one or more other hosts (transmit collisions as defined by IEEE 802.3k) plus receiver collisions observed on any coax segments to which the repeater is connected.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniOutDelayExceededDiscards		1.3.6.1.4.1.25506.2.42.5.1.2.1.18
The number of frames discarded by this port due to excessive transit delay through the bridge. It is incremented by both transparent and source route bridges.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniOutErrorbyOther		1.3.6.1.4.1.25506.2.42.5.1.2.1.19
The total number of other error frames sent on this interface. Other error frames means the error frames out of collision frames and excessive delayed frames.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniOutDroppedFrames		1.3.6.1.4.1.25506.2.42.5.1.2.1.20
The total number of frames dropped because of buffer failure.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hh3cEponUniIgmpInfoTable		1.3.6.1.4.1.25506.2.42.5.1.3
This table stores igmp information of UNI interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponUniIgmpInfoEntry

hh3cEponUniIgmpInfoEntry		1.3.6.1.4.1.25506.2.42.5.1.3.1
The entry of hh3cEponUniIgmpInfoTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponUniIgmpInfoEntry

hh3cEponUniMacIndex		1.3.6.1.4.1.25506.2.42.5.1.3.1.1
The index uniquely identifies the igmp information in current UNI interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

hh3cEponUniIgmpMacAddress		1.3.6.1.4.1.25506.2.42.5.1.3.1.2
A 6-octet read-only value carrying the individual MAC address indicates which igmp group the UNI interface belonging to.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

hh3cEponUniIgmpVlanId		1.3.6.1.4.1.25506.2.42.5.1.3.1.3
An integer range from 1 to 4094 indicates the vlan which the igmp Mac address has joined in.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

hh3cEponUniParaMan		1.3.6.1.4.1.25506.2.42.5.1.4
OBJECT IDENTIFIER

hh3cEponUniLineRateMax		1.3.6.1.4.1.25506.2.42.5.1.4.1
The maximum value of the line-rate(kbps) that user network interface can be set.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponUniLineRateStep		1.3.6.1.4.1.25506.2.42.5.1.4.2
The step of line-rate(kbps).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponUniNumberOnOnu		1.3.6.1.4.1.25506.2.42.5.1.4.3
The user network interface number on ONU.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponUniScalarGroup		1.3.6.1.4.1.25506.2.42.5.1.5
OBJECT IDENTIFIER

hh3cEponUniPortPolicyTable		1.3.6.1.4.1.25506.2.42.5.1.6
UNI port policy configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponUniPortPolicyEntry

hh3cEponUniPortPolicyEntry		1.3.6.1.4.1.25506.2.42.5.1.6.1
The entry of hh3cEponUniPortPolicyTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponUniPortPolicyEntry

hh3cEponUniPortPolicyStatus		1.3.6.1.4.1.25506.2.42.5.1.6.1.1
enable - enable UNI upstream port policing. disable - disable UNI upstream port policing.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

hh3cEponUniPortPolicyCir		1.3.6.1.4.1.25506.2.42.5.1.6.1.2
The committed information rate, ranging from 1 to 102400, measured in kbps.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hh3cEponUniPortPolicyBucketDepth		1.3.6.1.4.1.25506.2.42.5.1.6.1.3
The depth of the token bucket to tolerant the certain burst(CBS), ranging from 0 to 65535, measured in bytes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hh3cEponUniPortPolicyExtraBurst		1.3.6.1.4.1.25506.2.42.5.1.6.1.4
The extra token to permit the forwarding engine to finish the packet being sent when the bucket depth is exhausted, ranging from 0 to 65535, measured in bytes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hh3cEponUniPortPolicyInboundCir		1.3.6.1.4.1.25506.2.42.5.1.6.1.5
The inbound committed information rate, measured in kbps.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hh3cEponUniPortPolicyInboundBucketDepth		1.3.6.1.4.1.25506.2.42.5.1.6.1.6
The inbound depth of the token bucket to tolerant the certain burst(CBS), ranging from 0 to 65535, measured in bytes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hh3cEponUniPortPolicyInboundExtraBurst		1.3.6.1.4.1.25506.2.42.5.1.6.1.7
The inbound extra token to permit the forwarding engine to finish the packet being sent when the bucket depth is exhausted, ranging from 0 to 65535, measured in bytes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hh3cEponUniPortPolicyOutboundCir		1.3.6.1.4.1.25506.2.42.5.1.6.1.8
The outbound committed information rate, stepped by 64, measured in kbps.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hh3cEponUniPortPolicyOutboundPir		1.3.6.1.4.1.25506.2.42.5.1.6.1.9
The outbound peak information rate, stepped by 64, measured in kbps.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hh3cEponUniMulticastTable		1.3.6.1.4.1.25506.2.42.5.1.7
UNI multicast configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponUniMulticastEntry

hh3cEponUniMulticastEntry		1.3.6.1.4.1.25506.2.42.5.1.7.1
The entry of hh3cEponUniPortPolicyTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponUniMulticastEntry

hh3cEponUniMulticastGroupNumber		1.3.6.1.4.1.25506.2.42.5.1.7.1.1
The allowed multicast group number that can be handled at the same time by UNI.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hh3cEponUniMulticastVlanList		1.3.6.1.4.1.25506.2.42.5.1.7.1.2
The multicast vlan list. The first two octets of the string represent the first VLAN ID; the second two octets of the string represent the second VLAN ID, and so on. It is a zero length string by default.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..255)

hh3cEponUniMulticastStripStatus		1.3.6.1.4.1.25506.2.42.5.1.7.1.3
true - strip the vlan tag of multicast packet. false - does not strip the vlan tag of multicast packet.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

hh3cEponUniMulticastFastleave		1.3.6.1.4.1.25506.2.42.5.1.7.1.4
true(1) - fast leave of IGMP enable on ONU. false(2) - fast leave of IGMP disable on ONU.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cEponUniTechAbilityTable		1.3.6.1.4.1.25506.2.42.5.1.8
UNI multicast configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponUniTechAbilityEntry

hh3cEponUniTechAbilityEntry		1.3.6.1.4.1.25506.2.42.5.1.8.1
The entry of hh3cEponUniTechAbilityTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponUniTechAbilityEntry

hh3cEponUniLocalTechAbility		1.3.6.1.4.1.25506.2.42.5.1.8.1.1
The local port capabilities of the UNI. Each two octets stand for a capability of UNI: the first two octets represent one capability and the second two octets represent another capability, and so on. The capabilities list: 1 - undefined, 2 - initializing, true ability not yet known, 14 - 10BASE-T, 142 - full duplex 10BASE-T, 23 - 100BASE-T4, 25 - 100BASE-TX, 252 - full duplex 100BASE-TX, 312 - PAUSE operation for full duplex links, 313 - asymmetric PAUSE operation for full duplex links, 314 - symmetric PAUSE operation for full duplex links, 32 - 100BASE-T2, 322 - full duplex 100BASE-T2, 36 - 1000BASE-X, 362 - full duplex 1000BASE-X, 40 - 1000BASE-T UTP PHY, 402 - full duplex 1000BASE-T UTP PHY, 37 - remote fault bit 1(RF1), 372 - remote fault bit 2(RF2), 8029 - 802.9ISLAN-16T.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

hh3cEponUniAdvertisedTechAbility		1.3.6.1.4.1.25506.2.42.5.1.8.1.2
The advertised port capabilities of the UNI. The capabilities list references the description of hh3cEponUniLocalTechAbility.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

hh3cEponUniMulticastControlTable		1.3.6.1.4.1.25506.2.42.5.1.9
UNI multicast control parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponUniMulticastControlEntry

hh3cEponUniMulticastControlEntry		1.3.6.1.4.1.25506.2.42.5.1.9.1
The entry of the table hh3cEponUniMulticastControlTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponUniMulticastControlEntry

hh3cEponUniMulticastVlanIndex		1.3.6.1.4.1.25506.2.42.5.1.9.1.1
The multicast vlan ID.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hh3cEponUniMulticastAddressList		1.3.6.1.4.1.25506.2.42.5.1.9.1.2
The multicast address, each four octets represents a multicast address, the address section ranging from the first four octets to the second four octets, and the like.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..255)

hh3cEponUniMulticastAccessRule		1.3.6.1.4.1.25506.2.42.5.1.9.1.3
deny - deny the multicast packet. permit - permit the multicast packet. preview - permit the multicast packet with conditions.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	deny(1), permit(2), preview(3)

hh3cEponUniMulticastChannelLimit		1.3.6.1.4.1.25506.2.42.5.1.9.1.4
The limitation of multicast preview channel number.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hh3cEponUniMulticastPreTimeSlice		1.3.6.1.4.1.25506.2.42.5.1.9.1.5
The time slice of multicast preview.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hh3cEponUniMulticastPreTimes		1.3.6.1.4.1.25506.2.42.5.1.9.1.6
The number of multicast preview times.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hh3cEponUniMulticastPreInterval		1.3.6.1.4.1.25506.2.42.5.1.9.1.7
The interval between two consecutive previews, measured in minute.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hh3cEponUniMulticastRowStatus		1.3.6.1.4.1.25506.2.42.5.1.9.1.8
The status of this table entry. The active, createAndGo and the destory statuses are supported.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hh3cEponUniMulticastIndex		1.3.6.1.4.1.25506.2.42.5.1.9.1.9
The index of the entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

hh3cEponUniMulticastSourceIpList		1.3.6.1.4.1.25506.2.42.5.1.9.1.10
This list contains many source ip addresses. Each ip address is contained in four octets.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..255)

hh3cEponUniMulticastResetInterval		1.3.6.1.4.1.25506.2.42.5.1.9.1.11
The interval is measured in minute. From the last preview limitation is reached, a customer can preview again after this interval is expired.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hh3cEponUniQosIndexNextTable		1.3.6.1.4.1.25506.2.42.5.1.10
The next index table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponUniQosIndexNextEntry

hh3cEponUniQosIndexNextEntry		1.3.6.1.4.1.25506.2.42.5.1.10.1
The entry of the table hh3cEponUniQosIndexNextTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponUniQosIndexNextEntry

hh3cEponUniQosConfIndexNext		1.3.6.1.4.1.25506.2.42.5.1.10.1.1
This object contains an appropriate value to be used for hh3cEponUniQosConfIndex when creating rows in the hh3cEponUniQosConfTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponUniQosConfTable		1.3.6.1.4.1.25506.2.42.5.1.11
UNI Qos configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponUniQosConfEntry

hh3cEponUniQosConfEntry		1.3.6.1.4.1.25506.2.42.5.1.11.1
The entry of the table hh3cEponUniQosConfTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponUniQosConfEntry

hh3cEponUniQosConfIndex		1.3.6.1.4.1.25506.2.42.5.1.11.1.1
The rule index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

hh3cEponUniQosConfRuleIndexNext		1.3.6.1.4.1.25506.2.42.5.1.11.1.2
This object contains an appropriate value to be used for hh3cEponUniQosRuleIndex when creating rows in the hh3cEponUniQosRuleTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponUniQosConfMappedQueue		1.3.6.1.4.1.25506.2.42.5.1.11.1.3
The queue that the ethernet frames will be mapped.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hh3cEponUniQosConfMarkedPriority		1.3.6.1.4.1.25506.2.42.5.1.11.1.4
Priority of the ethernet frames to be marked, which compliant with the 802.1D user priority standard.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hh3cEponUniQosConfRowStatus		1.3.6.1.4.1.25506.2.42.5.1.11.1.5
The status of this table entry. The active, createAndGo and the destory statuses are supported.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hh3cEponUniQosRuleTable		1.3.6.1.4.1.25506.2.42.5.1.12
Qos sub rule of the UNI.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponUniQosRuleEntry

hh3cEponUniQosRuleEntry		1.3.6.1.4.1.25506.2.42.5.1.12.1
The entry of the table hh3cEponUniQosRuleTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponUniQosRuleEntry

hh3cEponUniQosRuleIndex		1.3.6.1.4.1.25506.2.42.5.1.12.1.1
The sub rule index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..255

hh3cEponUniQosRuleSelector		1.3.6.1.4.1.25506.2.42.5.1.12.1.2
The ethernet frame selector. dstmac - based on destination MAC address. srcmac - based on source MAC address. ethernetpriority - based on ethernet priority. vlanid - based on VLAN ID. ethernettype - based on ethernet type. dstip - based on destination IP address. srcip - based on source IP address. ipprototype - based on IP type(ipv4 or ipv6). ipv4tosdscp - based on IP TOS/DSCP. ipv6 - based IP precedence. srcport - based on layer 4 source port. dstport - based on layer 4 destination port.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	dstmac(1), srcmac(2), ethernetpriority(3), vlanid(4), ethernettype(5), dstip(6), srcip(7), ipprototype(8), ipv4tosdscp(9), ipv6precedence(10), srcport(11), dstport(12)

hh3cEponUniQosRuleValue		1.3.6.1.4.1.25506.2.42.5.1.12.1.3
The rule value based on the hh3cEponUniQosRuleSelector.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hh3cEponUniQosRuleMacAddress		1.3.6.1.4.1.25506.2.42.5.1.12.1.4
MAC Address.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

hh3cEponUniQosRuleOperator		1.3.6.1.4.1.25506.2.42.5.1.12.1.5
nervermatch - value never match. equal - field equal to the value. notequal - field not equal to the value. lessthanequal - field less than or equal to the value. greaterthanequal - field greater than or equal to the value. fieldexist - value is ignored if field exists. fieldnotexist - value is ignored if field does not exist. alwaysmatch - value always match.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	nevermatch(1), equal(2), notequal(3), lessthanequal(4), greaterthanequal(5), fieldexist(6), fieldnotexist(7), alwaysmatch(8)

hh3cEponUniQosRuleRowStatus		1.3.6.1.4.1.25506.2.42.5.1.12.1.6
The status of this table entry. Only active, createAndGo and the destory are supported.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hh3cEponUniMirrorGroupTable		1.3.6.1.4.1.25506.2.42.5.1.13
Qos sub rule of the UNI.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponUniMirrorGroupEntry

hh3cEponUniMirrorGroupEntry		1.3.6.1.4.1.25506.2.42.5.1.13.1
The entry of the hh3cEponUniMirrorGroupTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponUniMirrorGroupEntry

hh3cEponUniMirrorGroupID		1.3.6.1.4.1.25506.2.42.5.1.13.1.1
Epon UNI mirror group ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

hh3cEponUniMirrorInboundPortList		1.3.6.1.4.1.25506.2.42.5.1.13.1.2
UNI inbound port list. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered UNI, and the least significant bit represents the lowest numbered UNI. Thus, each UNI port is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is allowed in the set of ports. the port is not allowed if its bit has a value of '0'.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

hh3cEponUniMirrorOutboundPortList		1.3.6.1.4.1.25506.2.42.5.1.13.1.3
UNI outnbound port list, more infomation reference hh3cEponUniMirrorInboundPortList
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

hh3cEponUniMonitorPort		1.3.6.1.4.1.25506.2.42.5.1.13.1.4
UNI monitor port.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hh3cEponUniMirrorRowStatus		1.3.6.1.4.1.25506.2.42.5.1.13.1.5
RowStatus, Now support three status: createAndGo, active, destroy.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hh3cEponUniMirrorGroupIdNextTable		1.3.6.1.4.1.25506.2.42.5.1.14
The next index table, which is used by hh3cEponUniMirrorGroupTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponUniMirrorGroupIdNextEntry

hh3cEponUniMirrorGroupIdNextEntry		1.3.6.1.4.1.25506.2.42.5.1.14.1
The entry of the table hh3cEponUniMirrorGroupIdNextEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponUniMirrorGroupIdNextEntry

hh3cEponUniMirrorGroupIDNext		1.3.6.1.4.1.25506.2.42.5.1.14.1.1
This object contains an appropriate value to be used for hh3cEponUniMirrorGroupID when creating rows in the hh3cEponUniMirrorGroupTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponUniMulticastCtrlInfoTable		1.3.6.1.4.1.25506.2.42.5.1.15
UNI multicast information which is active .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponUniMulticastCtrlInfoEntry

hh3cEponUniMulticastCtrlInfoEntry		1.3.6.1.4.1.25506.2.42.5.1.15.1
The entry of the table hh3cEponUniMulticastCtrlInfoTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponUniMulticastCtrlInfoEntry

hh3cEponUniMultActVlan		1.3.6.1.4.1.25506.2.42.5.1.15.1.1
The multicast vlan ID which is active.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

hh3cEponUniMultActAddress		1.3.6.1.4.1.25506.2.42.5.1.15.1.2
The multicast address which is active.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

hh3cEponUniMultActAccessRule		1.3.6.1.4.1.25506.2.42.5.1.15.1.3
deny - deny the multicast packet. permit - permit the multicast packet. preview - permit the multicast packet with conditions.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	deny(1), permit(2), preview(3)

hh3cEponUniMultActPreTimes		1.3.6.1.4.1.25506.2.42.5.1.15.1.4
The number of multicast preview times which is active.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponUniMultActPreRemain		1.3.6.1.4.1.25506.2.42.5.1.15.1.5
The remanent time slice of multicast preview which is active.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponUniMulticastIndexNextTable		1.3.6.1.4.1.25506.2.42.5.1.16
The next index table, which is used by hh3cEponUniMulticastControlTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cEponUniMulticastIndexNextEntry

hh3cEponUniMulticastIndexNextEntry		1.3.6.1.4.1.25506.2.42.5.1.16.1
The entry of the table hh3cEponUniMulticastIndexNextEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cEponUniMulticastIndexNextEntry

hh3cEponUniMulticastConfIndexNext		1.3.6.1.4.1.25506.2.42.5.1.16.1.1
This object contains an appropriate value to be used for hh3cEponUniMulticastIndex when creating rows in the hh3cEponUniMulticastControlTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hh3cEponUniTrap		1.3.6.1.4.1.25506.2.42.5.2
OBJECT IDENTIFIER

hh3cEponUniTrapPrefix		1.3.6.1.4.1.25506.2.42.5.2.0
OBJECT IDENTIFIER

hh3cEponUniLinkUpTrap		1.3.6.1.4.1.25506.2.42.5.2.0.1
A hh3cEponUniLinkUpTrap notification is sent when the UNI up event is detected and the transmitting switch is turned on.
Status: current	Access: read-only
NOTIFICATION-TYPE

hh3cEponUniLinkDownTrap		1.3.6.1.4.1.25506.2.42.5.2.0.2
A hh3cEponUniLinkDownTrap notification is sent when the UNI down event is detected and the transmitting switch is turned on.
Status: current	Access: read-only
NOTIFICATION-TYPE

hh3cEponUniLoopBackDetectedTrap		1.3.6.1.4.1.25506.2.42.5.2.0.3
A hh3cEponUniLoopBackDetectedTrap notification is sent when the UNI loopback event is detected.
Status: current	Access: read-only
NOTIFICATION-TYPE

hh3cEponUniLoopBackRecoveredTrap		1.3.6.1.4.1.25506.2.42.5.2.0.4
A hh3cEponUniLoopBackRecoveredTrap notification is sent when the UNI loopback is recovered.
Status: current	Access: read-only
NOTIFICATION-TYPE