HH3C-MPLS-LSR-MIB

File: HH3C-MPLS-LSR-MIB.mib (65913 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
IF-MIB	HH3C-OID-MIB	IANA-ADDRESS-FAMILY-NUMBERS-MIB
INET-ADDRESS-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
Integer32	Counter32	Unsigned32
Counter64	Gauge32	MODULE-COMPLIANCE
OBJECT-GROUP	NOTIFICATION-GROUP	TEXTUAL-CONVENTION
TruthValue	RowStatus	StorageType
RowPointer	TimeStamp	InterfaceIndex
InterfaceIndexOrZero	hh3cMpls	AddressFamilyNumbers
InetAddressIPv4	InetAddressIPv6	InetAddressType

Defined Types

Hh3cMplsLSPID
An identifier that is assigned to each LSP and is used to uniquely identify it. This is assigned at the head end of the LSP and can be used by all LSRs to identify this LSP. This value is piggybacked by the signaling protocol when this LSP is signaled within the network. This identifier can then be used at each LSR to identify which labels are being swapped to other labels for this LSP. For IPv4 addresses this results in a 6-octet long cookie.
TEXTUAL-CONVENTION
	OCTET STRING	Size(0..31)

Hh3cMplsLabel
This value represents an MPLS label. Note that the contents of a label field are interpreted in an interface-type specific fashion. For example, the 20-bit wide label carried in the MPLS shim header is contained in bits 0-19 and bits 20-31 must be zero. The frame relay label can be either 10 or 23 bits wide depending on the size of the DLCI field and bits 10-31, or 23-31 must be zero, respectively. For an ATM interface, bits 0-15 must be interpreted as the VCI, bits 16-23 as the VPI and bits 24-31 must be zero. Note that the permissible label values are also a function of the interface type. For example, the value 3 has special semantics in the control plane for an MPLS shim header label and is not a valid label value in the data path.
TEXTUAL-CONVENTION
	Unsigned32	0..4294967295

Hh3cMplsBitRate
An estimate of bandwidth in units of 1,000 bits per second. If this object reports a value of 'n' then the rate of the object is somewhere in the range of 'n-500' to 'n+499'. For objects which do not vary in bitrate, or for those where no accurate estimation can be made, this object should contain the nominal bitrate.
TEXTUAL-CONVENTION
	Integer32	1..2147483647

Hh3cMplsBurstSize
The number of octets of MPLS data that the stream may send back-to-back without concern for policing.
TEXTUAL-CONVENTION
	Integer32	1..2147483647

Hh3cMplsObjectOwner
The entity which owns the object in question.
TEXTUAL-CONVENTION
	INTEGER	other(1), snmp(2), ldp(3), rsvp(4), crldp(5), policyAgent(6), unknown(7)

Hh3cMplsInterfaceConfEntry
SEQUENCE
	hh3cmplsInterfaceConfIndex	InterfaceIndexOrZero
	hh3cmplsInterfaceLabelMinIn	Hh3cMplsLabel
	hh3cmplsInterfaceLabelMaxIn	Hh3cMplsLabel
	hh3cmplsInterfaceLabelMinOut	Hh3cMplsLabel
	hh3cmplsInterfaceLabelMaxOut	Hh3cMplsLabel
	hh3cmplsInterfaceTotalBandwidth	Hh3cMplsBitRate
	hh3cmplsInterfaceAvailableBandwidth	Hh3cMplsBitRate
	hh3cmplsInterfaceLabelParticipationType	BITS
	hh3cmplsInterfaceConfStorageType	StorageType

Hh3cMplsInterfacePerfEntry
SEQUENCE
	hh3cmplsInterfaceInLabelsUsed	Gauge32
	hh3cmplsInterfaceFailedLabelLookup	Counter32
	hh3cmplsInterfaceOutLabelsUsed	Gauge32
	hh3cmplsInterfaceOutFragments	Counter32

Hh3cMplsInSegmentEntry
SEQUENCE
	hh3cmplsInSegmentIfIndex	InterfaceIndexOrZero
	hh3cmplsInSegmentLabel	Hh3cMplsLabel
	hh3cmplsInSegmentNPop	Integer32
	hh3cmplsInSegmentAddrFamily	AddressFamilyNumbers
	hh3cmplsInSegmentXCIndex	Integer32
	hh3cmplsInSegmentOwner	Hh3cMplsObjectOwner
	hh3cmplsInSegmentTrafficParamPtr	RowPointer
	hh3cmplsInSegmentRowStatus	RowStatus
	hh3cmplsInSegmentStorageType	StorageType

Hh3cMplsInSegmentPerfEntry
SEQUENCE
	hh3cmplsInSegmentOctets	Counter32
	hh3cmplsInSegmentPackets	Counter32
	hh3cmplsInSegmentErrors	Counter32
	hh3cmplsInSegmentDiscards	Counter32
	hh3cmplsInSegmentHCOctets	Counter64
	hh3cmplsInSegmentPerfDiscontinuityTime	TimeStamp

Hh3cMplsOutSegmentEntry
SEQUENCE
	hh3cmplsOutSegmentIndex	Integer32
	hh3cmplsOutSegmentIfIndex	InterfaceIndex
	hh3cmplsOutSegmentPushTopLabel	TruthValue
	hh3cmplsOutSegmentTopLabel	Hh3cMplsLabel
	hh3cmplsOutSegmentNextHopIpAddrType	InetAddressType
	hh3cmplsOutSegmentNextHopIpv4Addr	InetAddressIPv4
	hh3cmplsOutSegmentNextHopIpv6Addr	InetAddressIPv6
	hh3cmplsOutSegmentXCIndex	Integer32
	hh3cmplsOutSegmentOwner	Hh3cMplsObjectOwner
	hh3cmplsOutSegmentTrafficParamPtr	RowPointer
	hh3cmplsOutSegmentRowStatus	RowStatus
	hh3cmplsOutSegmentStorageType	StorageType

Hh3cMplsOutSegmentPerfEntry
SEQUENCE
	hh3cmplsOutSegmentOctets	Counter32
	hh3cmplsOutSegmentPackets	Counter32
	hh3cmplsOutSegmentErrors	Counter32
	hh3cmplsOutSegmentDiscards	Counter32
	hh3cmplsOutSegmentHCOctets	Counter64
	hh3cmplsOutSegmentPerfDiscontinuityTime	TimeStamp

Hh3cMplsXCEntry
SEQUENCE
	hh3cmplsXCIndex	Integer32
	hh3cmplsXCLspId	Hh3cMplsLSPID
	hh3cmplsXCLabelStackIndex	Integer32
	hh3cmplsXCIsPersistent	TruthValue
	hh3cmplsXCOwner	Hh3cMplsObjectOwner
	hh3cmplsXCRowStatus	RowStatus
	hh3cmplsXCStorageType	StorageType
	hh3cmplsXCAdminStatus	INTEGER
	hh3cmplsXCOperStatus	INTEGER

Hh3cMplsLabelStackEntry
SEQUENCE
	hh3cmplsLabelStackIndex	Integer32
	hh3cmplsLabelStackLabelIndex	Integer32
	hh3cmplsLabelStackLabel	Hh3cMplsLabel
	hh3cmplsLabelStackRowStatus	RowStatus
	hh3cmplsLabelStackStorageType	StorageType

Hh3cMplsTrafficParamEntry
SEQUENCE
	hh3cmplsTrafficParamIndex	Integer32
	hh3cmplsTrafficParamMaxRate	Hh3cMplsBitRate
	hh3cmplsTrafficParamMeanRate	Hh3cMplsBitRate
	hh3cmplsTrafficParamMaxBurstSize	Hh3cMplsBurstSize
	hh3cmplsTrafficParamRowStatus	RowStatus
	hh3cmplsTrafficParamStorageType	StorageType

Defined Values

hh3cMplsLsr		1.3.6.1.4.1.25506.8.12.1
This MIB contains managed object definitions for the Multiprotocol Label Switching (MPLS) Router as defined in: Rosen, E., Viswanathan, A., and R. Callon, Multiprotocol Label Switching Architecture, Internet Draft , August 1999.
MODULE-IDENTITY

hh3cmplsLsrObjects		1.3.6.1.4.1.25506.8.12.1.1
OBJECT IDENTIFIER

hh3cmplsLsrNotifications		1.3.6.1.4.1.25506.8.12.1.2
OBJECT IDENTIFIER

hh3cmplsLsrNotifyPrefix		1.3.6.1.4.1.25506.8.12.1.2.0
OBJECT IDENTIFIER

hh3cmplsLsrConformance		1.3.6.1.4.1.25506.8.12.1.3
OBJECT IDENTIFIER

hh3cmplsInterfaceConfTable		1.3.6.1.4.1.25506.8.12.1.1.1
This table specifies per-interface MPLS capability and associated information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cMplsInterfaceConfEntry

hh3cmplsInterfaceConfEntry		1.3.6.1.4.1.25506.8.12.1.1.1.1
An entry in this table is created by an LSR for every interface capable of supporting MPLS. The entry with index 0 represents the per-platform label space and contains parameters that apply to all interfaces that participate in the per-platform label space. Other entries defined in this table represent additional MPLS interfaces that may participate in either the per-platform or per- interface label spaces, or both. Additional information about label space participation of an interface is provided in the description clause of hh3cmplsInterfaceLabelParticipationType.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cMplsInterfaceConfEntry

hh3cmplsInterfaceConfIndex		1.3.6.1.4.1.25506.8.12.1.1.1.1.1
This is a unique index for an entry in the hh3cmplsInterfaceConfTable. A non-zero index for an entry indicates the ifIndex for the corresponding interface entry in of the MPLS-layer in the ifTable. Note that the per-platform label space may apply to several interfaces, and therefore the configuration of the per-platform label space interface parameters will apply to all of the interfaces that are participating in the per-platform label space.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndexOrZero

hh3cmplsInterfaceLabelMinIn		1.3.6.1.4.1.25506.8.12.1.1.1.1.2
This is the minimum value of an MPLS label that this LSR is willing to receive on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Hh3cMplsLabel

hh3cmplsInterfaceLabelMaxIn		1.3.6.1.4.1.25506.8.12.1.1.1.1.3
This is the maximum value of an MPLS label that this LSR is willing to receive on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Hh3cMplsLabel

hh3cmplsInterfaceLabelMinOut		1.3.6.1.4.1.25506.8.12.1.1.1.1.4
This is the minimum value of an MPLS label that this LSR is willing to send on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Hh3cMplsLabel

hh3cmplsInterfaceLabelMaxOut		1.3.6.1.4.1.25506.8.12.1.1.1.1.5
This is the maximum value of an MPLS label that this LSR is willing to send on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Hh3cMplsLabel

hh3cmplsInterfaceTotalBandwidth		1.3.6.1.4.1.25506.8.12.1.1.1.1.6
This value indicates the total amount of usable bandwidth on this interface and is specified in kilobits per second (Kbps). This variable is not applicable when applied to the interface with index 0.
Status: current	Access: read-only
OBJECT-TYPE
	Hh3cMplsBitRate

hh3cmplsInterfaceAvailableBandwidth		1.3.6.1.4.1.25506.8.12.1.1.1.1.7
This value indicates the total amount of available bandwidth available on this interface and is specified in kilobits per second (Kbps). This value is calculated as the difference between the amount of bandwidth currently in use and that specified in hh3cmplsInterfaceTotalBandwidth. This variable is not applicable when applied to the interface with index 0.
Status: current	Access: read-only
OBJECT-TYPE
	Hh3cMplsBitRate

hh3cmplsInterfaceLabelParticipationType		1.3.6.1.4.1.25506.8.12.1.1.1.1.8
Either the perPlatform(0) or perInterface(1) bit MUST be set. If the value of the hh3cmplsInterfaceConfIndex for this entry is zero, then only the perPlatform(0) bit MUST be set and the perInterface(1) bit is meaningless. If the perInterface(1) bit is set then the value of hh3cmplsInterfaceLabelMinIn, hh3cmplsInterfaceLabelMaxIn, hh3cmplsInterfaceLabelMinOut, and hh3cmplsInterfaceLabelMaxOut for this entry reflect the label ranges for this interface. If only the perPlatform(0) bit is set, then the value of hh3cmplsInterfaceLabelMinIn, hh3cmplsInterfaceLabelMaxIn, hh3cmplsInterfaceLabelMinOut, and hh3cmplsInterfaceLabelMaxOut for this entry must be identical to the instance of these objects with index 0.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	perPlatform(0), perInterface(1)

hh3cmplsInterfaceConfStorageType		1.3.6.1.4.1.25506.8.12.1.1.1.1.9
The storage type for this entry.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

hh3cmplsInterfacePerfTable		1.3.6.1.4.1.25506.8.12.1.1.2
This table provides MPLS performance information on a per-interface basis.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cMplsInterfacePerfEntry

hh3cmplsInterfacePerfEntry		1.3.6.1.4.1.25506.8.12.1.1.2.1
An entry in this table is created by the LSR for every interface capable of supporting MPLS. Its is an extension to the hh3cmplsInterfaceConfEntry table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cMplsInterfacePerfEntry

hh3cmplsInterfaceInLabelsUsed		1.3.6.1.4.1.25506.8.12.1.1.2.1.1
This object counts the number of labels that are in use at this point in time on this interface in the incoming direction. If the interface participates in the per-platform label space only, then this instance of this object MUST be identical with the instance with index 0. If the interface participates in the per-interface label space, then this this instance of this object MUST represent the number of of per-interface labels that are in use at this point in time on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cmplsInterfaceFailedLabelLookup		1.3.6.1.4.1.25506.8.12.1.1.2.1.2
This object counts the number of labeled packets that have been received on this interface and were discarded because there was no matching cross-connect entry. This object MUST count on a per-interface basis regardless of which label space the interface participates in.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cmplsInterfaceOutLabelsUsed		1.3.6.1.4.1.25506.8.12.1.1.2.1.3
This object counts the number of top-most labels in the outgoing label stacks that are in use at this point in time on this interface. This object MUST count on a per-interface basis regardless of which label space the interface participates in.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

hh3cmplsInterfaceOutFragments		1.3.6.1.4.1.25506.8.12.1.1.2.1.4
This object counts the number of outgoing MPLS packets that required fragmentation before transmission on this interface. This object transmission on this interface. This object MUST count on a per-interface basis regardless of which label space the interface participates in.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cmplsInSegmentTable		1.3.6.1.4.1.25506.8.12.1.1.3
This table contains a collection of incoming segments to an LSR.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cMplsInSegmentEntry

hh3cmplsInSegmentEntry		1.3.6.1.4.1.25506.8.12.1.1.3.1
An entry in this table represents one incoming segment. An entry can be created by a network administrator or an SNMP agent, or an MPLS signaling protocol. The creator of the entry is denoted by hh3cmplsInSegmentOwner. An entry in this table is indexed by the ifIndex of the incoming interface and the (top) label.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cMplsInSegmentEntry

hh3cmplsInSegmentIfIndex		1.3.6.1.4.1.25506.8.12.1.1.3.1.1
This is a unique index for an entry in the hh3cmplsInSegmentTable. This value represents the interface index for the incoming MPLS interface. A value of zero represents an incoming label from the per-platform label space. In this case, the hh3cmplsInSegmentLabel is interpreted to be an MPLS-type label.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	InterfaceIndexOrZero

hh3cmplsInSegmentLabel		1.3.6.1.4.1.25506.8.12.1.1.3.1.2
The incoming label for this segment.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Hh3cMplsLabel

hh3cmplsInSegmentNPop		1.3.6.1.4.1.25506.8.12.1.1.3.1.3
The number of labels to pop from the incoming packet. Normally only the top label is popped from the packet and used for all switching decisions for that packet. Note that technologies which do not support label popping should set this value to its default value of 1.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..2147483647

hh3cmplsInSegmentAddrFamily		1.3.6.1.4.1.25506.8.12.1.1.3.1.4
The IANA address family [IANAFamily] of the incoming packet. A value of other(0) indicates that the family type is either unknown or undefined.
Status: current	Access: read-create
OBJECT-TYPE
	AddressFamilyNumbers

hh3cmplsInSegmentXCIndex		1.3.6.1.4.1.25506.8.12.1.1.3.1.5
Index into hh3cmplsXCTable which identifies which cross- connect entry this segment is part of. A value of zero indicates that this entry is not referred to by any cross-connect entry. When a cross-connect entry is created which this in-segment is a part of, this object is automatically updated to reflect the value of hh3cmplsXCIndex of that cross-connect entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

hh3cmplsInSegmentOwner		1.3.6.1.4.1.25506.8.12.1.1.3.1.6
Denotes the entity that created and is responsible for managing this segment.
Status: current	Access: read-create
OBJECT-TYPE
	Hh3cMplsObjectOwner

hh3cmplsInSegmentTrafficParamPtr		1.3.6.1.4.1.25506.8.12.1.1.3.1.7
This variable represents a pointer to the traffic parameter specification for this in-segment. This value may point at an entry in the hh3cmplsTrafficParamTable to indicate which hh3cmplsTrafficParamEntry is to be assigned to this segment. This value may optionally point at an externally defined traffic parameter specification table. A value of zero-dot-zero indicates best-effort treatment. By having the same value of this object, two or more segments can indicate resource sharing.
Status: current	Access: read-create
OBJECT-TYPE
	RowPointer

hh3cmplsInSegmentRowStatus		1.3.6.1.4.1.25506.8.12.1.1.3.1.8
This variable is used to create, modify, and/or delete a row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hh3cmplsInSegmentStorageType		1.3.6.1.4.1.25506.8.12.1.1.3.1.9
This variable indicates the storage type for this object.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

hh3cmplsInSegmentPerfTable		1.3.6.1.4.1.25506.8.12.1.1.4
This table contains statistical information for incoming MPLS segments to an LSR.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cMplsInSegmentPerfEntry

hh3cmplsInSegmentPerfEntry		1.3.6.1.4.1.25506.8.12.1.1.4.1
An entry in this table contains statistical information about one incoming segment which was configured in the hh3cmplsInSegmentTable. The counters in this entry should behave in a manner similar to that of the interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cMplsInSegmentPerfEntry

hh3cmplsInSegmentOctets		1.3.6.1.4.1.25506.8.12.1.1.4.1.1
This value represents the total number of octets received by this segment.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cmplsInSegmentPackets		1.3.6.1.4.1.25506.8.12.1.1.4.1.2
Total number of packets received by this segment.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cmplsInSegmentErrors		1.3.6.1.4.1.25506.8.12.1.1.4.1.3
The number of errored packets received on this segment.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cmplsInSegmentDiscards		1.3.6.1.4.1.25506.8.12.1.1.4.1.4
The number of labeled packets received on this in- segment, which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a labeled packet could be to free up buffer space.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cmplsInSegmentHCOctets		1.3.6.1.4.1.25506.8.12.1.1.4.1.5
The total number of octets received. This is the 64 bit version of hh3cmplsInSegmentOctets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

hh3cmplsInSegmentPerfDiscontinuityTime		1.3.6.1.4.1.25506.8.12.1.1.4.1.6
The value of sysUpTime on the most recent occasion at which any one or more of this segment's Counter32 or Counter64 suffered a discontinuity. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

hh3cmplsOutSegmentIndexNext		1.3.6.1.4.1.25506.8.12.1.1.5
This object contains the next appropriate value to be used for hh3cmplsOutSegmentIndex when creating entries in the hh3cmplsOutSegmentTable. If the number of unassigned entries is exhausted, this object will take on the value of 0. To obtain the hh3cmplsOutSegmentIndex value for a new entry, the manager must first issue a management protocol retrieval operation to obtain the current value of this object. The agent should modify the value to reflect the next unassigned index after each retrieval operation. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

hh3cmplsOutSegmentTable		1.3.6.1.4.1.25506.8.12.1.1.6
This table contains a representation of the outgoing segments from an LSR.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cMplsOutSegmentEntry

hh3cmplsOutSegmentEntry		1.3.6.1.4.1.25506.8.12.1.1.6.1
An entry in this table represents one outgoing segment. An entry can be created by a network administrator or an SNMP agent, or an MPLS signaling protocol. The object hh3cmplsOutSegmentOwner indicates the creator of this entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cMplsOutSegmentEntry

hh3cmplsOutSegmentIndex		1.3.6.1.4.1.25506.8.12.1.1.6.1.1
This value contains a unique index for this row. While a value of 0 is not valid as an index for this row it can be supplied as a valid value to index hh3cmplsXCTable to access entries for which no out- segment has been configured.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32	0..2147483647

hh3cmplsOutSegmentIfIndex		1.3.6.1.4.1.25506.8.12.1.1.6.1.2
This value contains the interface index of the outgoing interface.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndex

hh3cmplsOutSegmentPushTopLabel		1.3.6.1.4.1.25506.8.12.1.1.6.1.3
This value indicates whether or not a top label should be pushed onto the outgoing packet's label stack. The value of this variable must be set to true if the outgoing interface does not support pop- and-go (for example an ATM interface) or if it is a tunnel origination. Note that it is considered an error in the case that hh3cmplsOutSegmentPushTopLabel is set to false, but the cross-connect entry which refers to this out-segment has a non-zero hh3cmplsLabelStackIndex. The LSR MUST ensure that this situation does not happen
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

hh3cmplsOutSegmentTopLabel		1.3.6.1.4.1.25506.8.12.1.1.6.1.4
If hh3cmplsOutSegmentPushTopLabel is true then this represents the label that should be pushed onto the top of the outgoing packet's label stack.
Status: current	Access: read-create
OBJECT-TYPE
	Hh3cMplsLabel

hh3cmplsOutSegmentNextHopIpAddrType		1.3.6.1.4.1.25506.8.12.1.1.6.1.5
Indicates whether the next hop address is IPv4 or IPv6. Note that a value of unknown (0) is valid only when the outgoing interface is of type point-to- point.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressType

hh3cmplsOutSegmentNextHopIpv4Addr		1.3.6.1.4.1.25506.8.12.1.1.6.1.6
IPv4 Address of the next hop. Its value is significant only when hh3cmplsOutSegmentNextHopIpAddrType is ipV4 (1), otherwise it should return a value of 0.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressIPv4

hh3cmplsOutSegmentNextHopIpv6Addr		1.3.6.1.4.1.25506.8.12.1.1.6.1.7
IPv6 address of the next hop. Its value is significant only when hh3cmplsOutSegmentNextHopIpAddrType is ipV6 (2), otherwise it should return a value of 0.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressIPv6

hh3cmplsOutSegmentXCIndex		1.3.6.1.4.1.25506.8.12.1.1.6.1.8
Index into hh3cmplsXCTable which identifies which cross- connect entry this segment is part of. A value of zero indicates that this entry is not referred to by any cross-connect entry. When a cross-connect entry is created which this out-segment is a part of, this object is automatically updated to reflect the value of hh3cmplsXCIndex of that cross-connect entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

hh3cmplsOutSegmentOwner		1.3.6.1.4.1.25506.8.12.1.1.6.1.9
Denotes the entity which created and is responsible for managing this segment.
Status: current	Access: read-create
OBJECT-TYPE
	Hh3cMplsObjectOwner

hh3cmplsOutSegmentTrafficParamPtr		1.3.6.1.4.1.25506.8.12.1.1.6.1.10
This variable represents a pointer to the traffic parameter specification for this out-segment. This value may point at an entry in the hh3cmplsTrafficParamTable to indicate which hh3cmplsTrafficParamEntry is to be assigned to this segment. This value may optionally point at an externally defined traffic parameter specification table. A value of zero-dot-zero indicates best- effort treatment. By having the same value of this object, two or more segments can indicate resource sharing.
Status: current	Access: read-create
OBJECT-TYPE
	RowPointer

hh3cmplsOutSegmentRowStatus		1.3.6.1.4.1.25506.8.12.1.1.6.1.11
For creating, modifying, and deleting this row.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hh3cmplsOutSegmentStorageType		1.3.6.1.4.1.25506.8.12.1.1.6.1.12
This variable indicates the storage type for this object.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

hh3cmplsOutSegmentPerfTable		1.3.6.1.4.1.25506.8.12.1.1.7
This table contains statistical information about outgoing segments from an LSR. The counters in this entry should behave in a manner similar to that of the interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cMplsOutSegmentPerfEntry

hh3cmplsOutSegmentPerfEntry		1.3.6.1.4.1.25506.8.12.1.1.7.1
An entry in this table contains statistical information about one outgoing segment configured in hh3cmplsOutSegmentTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cMplsOutSegmentPerfEntry

hh3cmplsOutSegmentOctets		1.3.6.1.4.1.25506.8.12.1.1.7.1.1
This value contains the total number of octets sent on this segment.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cmplsOutSegmentPackets		1.3.6.1.4.1.25506.8.12.1.1.7.1.2
This value contains the total number of packets sent on this segment.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cmplsOutSegmentErrors		1.3.6.1.4.1.25506.8.12.1.1.7.1.3
Number of packets that could not be sent due to errors on this segment.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cmplsOutSegmentDiscards		1.3.6.1.4.1.25506.8.12.1.1.7.1.4
The number of labeled packets received on this out- segment, which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a labeled packet could be to free up buffer space.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hh3cmplsOutSegmentHCOctets		1.3.6.1.4.1.25506.8.12.1.1.7.1.5
Total number of octets sent. This is the 64 bit version of hh3cmplsOutSegmentOctets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

hh3cmplsOutSegmentPerfDiscontinuityTime		1.3.6.1.4.1.25506.8.12.1.1.7.1.6
The value of sysUpTime on the most recent occasion at which any one or more of this segment's Counter32 or Counter64 suffered a discontinuity. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

hh3cmplsXCIndexNext		1.3.6.1.4.1.25506.8.12.1.1.8
This object contains an appropriate value to be used for hh3cmplsXCIndex when creating entries in the hh3cmplsXCTable. The value 0 indicates that no unassigned entries are available. To obtain the value of hh3cmplsXCIndex for a new entry in the hh3cmplsXCTable, the manager issues a management protocol retrieval operation to obtain the current value of hh3cmplsXCIndex. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

hh3cmplsXCTable		1.3.6.1.4.1.25506.8.12.1.1.9
This table specifies information for switching between LSP segments. It supports point-to-point, point-to-multipoint and multipoint-to-point connections. hh3cmplsLabelStackTable specifies the label stack information for a cross-connect LSR and is referred to from hh3cmplsXCTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cMplsXCEntry

hh3cmplsXCEntry		1.3.6.1.4.1.25506.8.12.1.1.9.1
A row in this table represents one cross-connect entry. The following objects index it: - cross-connect index hh3cmplsXCIndex that uniquely identifies a group of cross-connect entries - interface index of the in-segment, hh3cmplsInSegmentIfIndex - incoming label(s), hh3cmplsInSegmentLabel - out-segment index, hh3cmplsOutSegmentIndex Originating LSPs: These are represented by using the special combination of values hh3cmplsInSegmentIfIndex=0 and hh3cmplsInSegmentLabel=0 as indexes. In this case the hh3cmplsOutSegmentIndex MUST be non-zero. Terminating LSPs: These are represented by using the special value hh3cmplsOutSegmentIndex=0 as index. Special labels: Entries indexed by reserved MPLS label values 0 through 15 imply terminating LSPs and MUST have hh3cmplsOutSegmentIfIndex = 0. Note that situations where LSPs are terminated with incoming label equal to 0, should have hh3cmplsInSegmentIfIndex = 0 as well, but can be distinguished from originating LSPs because the hh3cmplsOutSegmentIfIndex = 0. The hh3cmplsOutSegmentIfIndex MUST only be set to 0 in cases of terminating LSPs. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling protocol.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cMplsXCEntry

hh3cmplsXCIndex		1.3.6.1.4.1.25506.8.12.1.1.9.1.1
Primary index for the conceptual row identifying a group of cross-connect segments.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32	1..2147483647

hh3cmplsXCLspId		1.3.6.1.4.1.25506.8.12.1.1.9.1.2
This value identifies the label switched path that this cross-connect entry belongs to.
Status: current	Access: read-create
OBJECT-TYPE
	Hh3cMplsLSPID

hh3cmplsXCLabelStackIndex		1.3.6.1.4.1.25506.8.12.1.1.9.1.3
Primary index into hh3cmplsLabelStackTable identifying a stack of labels to be pushed beneath the top label. Note that the top label identified by the out- segment ensures that all the components of a multipoint-to-point connection have the same outgoing label. A value of 0 indicates that no labels are to be stacked beneath the top label.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..2147483647

hh3cmplsXCIsPersistent		1.3.6.1.4.1.25506.8.12.1.1.9.1.4
Denotes whether or not this cross-connect entry and associated in- and out-segments should be restored automatically after failures. This value MUST be set to false in cases where this cross-connect entry was created by a signaling protocol.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

hh3cmplsXCOwner		1.3.6.1.4.1.25506.8.12.1.1.9.1.5
Denotes the entity that created and is responsible for managing this cross-connect.
Status: current	Access: read-create
OBJECT-TYPE
	Hh3cMplsObjectOwner

hh3cmplsXCRowStatus		1.3.6.1.4.1.25506.8.12.1.1.9.1.6
For creating, modifying, and deleting this row.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hh3cmplsXCStorageType		1.3.6.1.4.1.25506.8.12.1.1.9.1.7
Defines the storage type for this object.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

hh3cmplsXCAdminStatus		1.3.6.1.4.1.25506.8.12.1.1.9.1.8
The desired operational status of this segment.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3)

hh3cmplsXCOperStatus		1.3.6.1.4.1.25506.8.12.1.1.9.1.9
The actual operational status of this cross- connect.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3), unknown(4), dormant(5), notPresent(6), lowerLayerDown(7)

hh3cmplsMaxLabelStackDepth		1.3.6.1.4.1.25506.8.12.1.1.10
The maximum stack depth supported by this LSR.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

hh3cmplsLabelStackIndexNext		1.3.6.1.4.1.25506.8.12.1.1.11
This object contains an appropriate value to be used for hh3cmplsLabelStackIndex when creating entries in the hh3cmplsLabelStackTable. The value 0 indicates that no unassigned entries are available. To obtain an hh3cmplsLabelStackIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

hh3cmplsLabelStackTable		1.3.6.1.4.1.25506.8.12.1.1.12
This table specifies the label stack to be pushed onto a packet, beneath the top label. Entries into this table are referred to from hh3cmplsXCTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cMplsLabelStackEntry

hh3cmplsLabelStackEntry		1.3.6.1.4.1.25506.8.12.1.1.12.1
An entry in this table represents one label which is to be pushed onto an outgoing packet, beneath the top label. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling protocol.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cMplsLabelStackEntry

hh3cmplsLabelStackIndex		1.3.6.1.4.1.25506.8.12.1.1.12.1.1
Primary index for this row identifying a stack of labels to be pushed on an outgoing packet, beneath the top label.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

hh3cmplsLabelStackLabelIndex		1.3.6.1.4.1.25506.8.12.1.1.12.1.2
Secondary index for this row identifying one label of the stack. Note that an entry with a smaller hh3cmplsLabelStackLabelIndex would refer to a label higher up the label stack and would be popped at a downstream LSR before a label represented by a higher hh3cmplsLabelStackLabelIndex at a downstream LSR.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

hh3cmplsLabelStackLabel		1.3.6.1.4.1.25506.8.12.1.1.12.1.3
The label to pushed.
Status: current	Access: read-create
OBJECT-TYPE
	Hh3cMplsLabel

hh3cmplsLabelStackRowStatus		1.3.6.1.4.1.25506.8.12.1.1.12.1.4
For creating, modifying, and deleting this row.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hh3cmplsLabelStackStorageType		1.3.6.1.4.1.25506.8.12.1.1.12.1.5
Defines the storage type for this object.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

hh3cmplsTrafficParamIndexNext		1.3.6.1.4.1.25506.8.12.1.1.13
This object contains an appropriate value which will be used for hh3cmplsTrafficParamIndex when creating entries in the hh3cmplsTrafficParamTable. The value 0 indicates that no unassigned entries are available. To obtain the hh3cmplsTrafficParamIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

hh3cmplsTrafficParamTable		1.3.6.1.4.1.25506.8.12.1.1.14
This table specifies the Traffic Parameter objects for in and out-segments.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hh3cMplsTrafficParamEntry

hh3cmplsTrafficParamEntry		1.3.6.1.4.1.25506.8.12.1.1.14.1
An entry in this table represents the TrafficParam objects for one or more in or out segments. A single entry can be pointed to by multiple segments indicating resource sharing.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hh3cMplsTrafficParamEntry

hh3cmplsTrafficParamIndex		1.3.6.1.4.1.25506.8.12.1.1.14.1.1
Uniquely identifies this row of the table. Note that zero represents an invalid index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

hh3cmplsTrafficParamMaxRate		1.3.6.1.4.1.25506.8.12.1.1.14.1.2
Maximum rate in kilobits/second.
Status: current	Access: read-create
OBJECT-TYPE
	Hh3cMplsBitRate

hh3cmplsTrafficParamMeanRate		1.3.6.1.4.1.25506.8.12.1.1.14.1.3
Mean rate in kilobits/second.
Status: current	Access: read-create
OBJECT-TYPE
	Hh3cMplsBitRate

hh3cmplsTrafficParamMaxBurstSize		1.3.6.1.4.1.25506.8.12.1.1.14.1.4
Maximum burst size in bytes.
Status: current	Access: read-create
OBJECT-TYPE
	Hh3cMplsBurstSize

hh3cmplsTrafficParamRowStatus		1.3.6.1.4.1.25506.8.12.1.1.14.1.5
For creating, modifying, and deleting this row.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hh3cmplsTrafficParamStorageType		1.3.6.1.4.1.25506.8.12.1.1.14.1.6
The storage type for this object.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

hh3cmplsXCTrapEnable		1.3.6.1.4.1.25506.8.12.1.1.15
If this object is true, then it enables the generation of hh3cmplsXCUp and hh3cmplsXCDown traps, otherwise these traps are not emitted.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hh3cmplsXCUp		1.3.6.1.4.1.25506.8.12.1.2.0.1
This notification is generated when a hh3cmplsXCOperStatus object for one of the configured cross-connect entries is about to leave the down state and transition into some other state (but not into the notPresent state). This other state is indicated by the included value of hh3cmplsXCOperStatus.
Status: current	Access: read-write
NOTIFICATION-TYPE

hh3cmplsXCDown		1.3.6.1.4.1.25506.8.12.1.2.0.2
This notification is generated when a hh3cmplsXCOperStatus object for one of the configured cross-connect entries is about to enter the down state from some other state (but not from the notPresent state). This other state is indicated by the included value of hh3cmplsXCOperStatus.
Status: current	Access: read-write
NOTIFICATION-TYPE

hh3cmplsLsrGroups		1.3.6.1.4.1.25506.8.12.1.3.1
OBJECT IDENTIFIER

hh3cmplsLsrCompliances		1.3.6.1.4.1.25506.8.12.1.3.2
OBJECT IDENTIFIER

hh3cmplsLsrModuleCompliance		1.3.6.1.4.1.25506.8.12.1.3.2.1
Compliance statement for agents that support the MPLS LSR MIB.
Status: current	Access: read-only
MODULE-COMPLIANCE

hh3cmplsInterfaceGroup		1.3.6.1.4.1.25506.8.12.1.3.1.1
Collection of objects needed for MPLS interface configuration and performance information.
Status: current	Access: read-only
OBJECT-GROUP

hh3cmplsInSegmentGroup		1.3.6.1.4.1.25506.8.12.1.3.1.2
Collection of objects needed to implement an in- segment.
Status: current	Access: read-only
OBJECT-GROUP

hh3cmplsOutSegmentGroup		1.3.6.1.4.1.25506.8.12.1.3.1.3
Collection of objects needed to implement an out- segment.
Status: current	Access: read-only
OBJECT-GROUP

hh3cmplsXCGroup		1.3.6.1.4.1.25506.8.12.1.3.1.4
Collection of objects needed to implement a cross-connect entry.
Status: current	Access: read-only
OBJECT-GROUP

hh3cmplsXCOptionalGroup		1.3.6.1.4.1.25506.8.12.1.3.1.5
Collection of optional objects for implementing a cross-connect entry.
Status: current	Access: read-only
OBJECT-GROUP

hh3cmplsPerfGroup		1.3.6.1.4.1.25506.8.12.1.3.1.6
Collection of objects providing performance information about an LSR.
Status: current	Access: read-only
OBJECT-GROUP

hh3cmplsHCInSegmentPerfGroup		1.3.6.1.4.1.25506.8.12.1.3.1.7
Object(s) providing performance information specific to out-segments for which the object hh3cmplsInterfaceInOctets wraps around too quickly.
Status: current	Access: read-only
OBJECT-GROUP

hh3cmplsHCOutSegmentPerfGroup		1.3.6.1.4.1.25506.8.12.1.3.1.8
Object(s) providing performance information specific to out-segments for which the object hh3cmplsInterfaceOutOctets wraps around too quickly.
Status: current	Access: read-only
OBJECT-GROUP

hh3cmplsTrafficParamGroup		1.3.6.1.4.1.25506.8.12.1.3.1.9
Object(s) required for supporting QoS resource reservation.
Status: current	Access: read-only
OBJECT-GROUP

hh3cmplsXCIsPersistentGroup		1.3.6.1.4.1.25506.8.12.1.3.1.10
Objects needed to support persistent cross- connects.
Status: current	Access: read-only
OBJECT-GROUP

hh3cmplsXCIsNotPersistentGroup		1.3.6.1.4.1.25506.8.12.1.3.1.11
Objects needed to support non-persistent cross- connects.
Status: current	Access: read-only
OBJECT-GROUP

hh3cmplsLabelStackGroup		1.3.6.1.4.1.25506.8.12.1.3.1.12
Objects needed to support label stacking.
Status: current	Access: read-only
OBJECT-GROUP

hh3cmplsSegmentDiscontinuityGroup		1.3.6.1.4.1.25506.8.12.1.3.1.13
A collection of objects providing information specific to segment discontinuities..
Status: current	Access: read-only
OBJECT-GROUP

hh3cmplsLsrNotificationGroup		1.3.6.1.4.1.25506.8.12.1.3.1.14
Set of notifications implemented in this module. None is mandatory.
Status: current	Access: read-only
NOTIFICATION-GROUP

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor