HMRINGARC-MGMT-SNMP-MIB
File:
HMRINGARC-MGMT-SNMP-MIB.mib (13711 bytes)
Imported modules
Imported symbols
Defined Types
HmArcCheckResultEntry |
|
SEQUENCE |
|
|
|
|
hmArcCheckStatusIndex |
Integer32 |
|
|
hmArcCheckStatusDeviceMac |
OCTET STRING |
|
|
hmArcCheckStatusDeviceIp |
IpAddress |
|
|
hmArcCheckStatusType |
INTEGER |
|
|
hmArcCheckStatusInfo |
DisplayString |
|
|
hmArcCheckStatusClassification |
INTEGER |
|
Defined Values
hmARC |
1.3.6.1.4.1.248.14.5.7 |
The Hirschmann Private Automatic Ring Configuration MIB definitions. |
MODULE-IDENTITY |
|
|
|
hmArcManagerAdminStatus |
1.3.6.1.4.1.248.14.5.7.1.1 |
The administratively desired status of the ARC manager.
enabled(1): ARC manager is active, the device can check and configure other ARC devices.
disabled(2): ARC manager is inactive, neither checking nor automatic configuring can be done. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enabled(1), disabled(2) |
|
hmArcManagerRedProtocol |
1.3.6.1.4.1.248.14.5.7.1.2 |
The ring redundancy protocol the clients will be configured for. Parameters like VLAN ID
and timings are taken from the current redundancy manager configuration.
mrp(1): Media Redundancy Protocol, according to IEC62439-2. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
mrp(1) |
|
hmArcManagerPrimGroupID |
1.3.6.1.4.1.248.14.5.7.1.3 |
Unique index to identify the slot number of
the primary link of the ARC manager. This value is never
greater than hmSysGroupCapacity. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
hmArcManagerPrimIfIndex |
1.3.6.1.4.1.248.14.5.7.1.4 |
Interface index of the primary link of the ARC manager. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
hmArcManagerRedGroupID |
1.3.6.1.4.1.248.14.5.7.1.5 |
Unique index to identify the slot number of
the redundant link of the ARC manager. This value is never
greater than hmSysGroupCapacity. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
hmArcManagerRedIfIndex |
1.3.6.1.4.1.248.14.5.7.1.6 |
Interface index of the redundant link of the ARC manager. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
hmArcManagerVlanID |
1.3.6.1.4.1.248.14.5.7.1.7 |
VLAN identifier of the ARC manager.
If value is set to 0 no VLAN is assigned. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
hmArcManagerAction |
1.3.6.1.4.1.248.14.5.7.1.8 |
The actions the ARC manager is able to activate.
This object, when read, returns noAction(1) if no action is currently running.
checkTopology(2): Checks the topology connected to the given primary and redundant
port and also fills the hmArcCheckResultTable, especially if an invalid topology
was found.
configureRing(3): Automatically configures the ring devices connected to the given
primary and redundant port. A successful checkTopology is prerequisite. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
noAction(1), checkTopology(2), configureRing(3) |
|
hmArcManagerActionResult |
1.3.6.1.4.1.248.14.5.7.1.9 |
Result of the last activated action.
noAction(1): Initial state, no action started.
pending(2): A topology check or a configuration process is going on.
closedRing(3): The topology check detected a ring topology which is ready for automatic configuration.
configuredRing(4): The topology check detected a partly or fully configured ring.
See the hmArcCheckResultTable for details. You may reconfigure it using ARC.
openRing(5): The topology check detected an open ring. It cannot be configured by ARC.
invalidTopology(6): An invalid topology was detected. See the hmArcCheckResultTable for details.
configFailed(7): One or more devices in the ring could not activate the configuration and are not
properly configured.
configSuccessful(8): The automatic configuration process was successful. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
noAction(1), pending(2), closedRing(3), configuredRing(4), openRing(5), invalidTopology(6), configFailed(7), configSuccessful(8) |
|
hmArcCheckResultTable |
1.3.6.1.4.1.248.14.5.7.2.1 |
Every entry in this table contains information about
the status of the network topology reported by the ARC devices. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
HmArcCheckResultEntry |
|
hmArcCheckResultEntry |
1.3.6.1.4.1.248.14.5.7.2.1.1 |
An entry in the hmArcCheckResultTable. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
HmArcCheckResultEntry |
|
|
hmArcCheckStatusDeviceMac |
1.3.6.1.4.1.248.14.5.7.2.1.1.2 |
The MAC address of the ARC device that reported
the status. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(6) |
|
hmArcCheckStatusDeviceIp |
1.3.6.1.4.1.248.14.5.7.2.1.1.3 |
The IP address of the ARC device that reported
the status. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
hmArcCheckStatusType |
1.3.6.1.4.1.248.14.5.7.2.1.1.4 |
The status an ARC device in the connected topology reported.
otherRm(1): the device detected another active Redundancy Manager.
loop(2): unclear topology detected. This may be a loop or a net segment
which is connected to the ring with Rapid Spanning Tree.
alreadyConfigured(3): the device already has a ring configured.
unsupportedOption(4): the device does not support one of the ARC Manager options.
openRing(5): the ARC Manager has detected an open Ring.
configFailed(6): the configuration of the device failed.
duplexMode(7): at least one Ring Port of the device is not in full duplex mode.
noArcDevices(8): there is no device in the ring which supports the ARC Protocol,
or all devices have hmArcClientAdminStatus set to disabled.
portState(9): at least one Ring Port of the device is not properly configured.
info(10): the device reported just additional information. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
otherRm(1), loop(2), alreadyConfigured(3), unsupportedOption(4), openRing(5), configFailed(6), duplexMode(7), noArcDevices(8), portState(9), info(10) |
|
hmArcCheckStatusInfo |
1.3.6.1.4.1.248.14.5.7.2.1.1.5 |
Additional information about the ARC device status.
The device may provide this information for each value in hmArcCheckStatusType. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
|
|
hmArcCheckStatusClassification |
1.3.6.1.4.1.248.14.5.7.2.1.1.6 |
Classification of the status the ARC device reported.
error(1): the reported status is an error.
warning(2): the reported status is a warning.
ok(3): the reported status is an information. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
error(1), warning(2), ok(3) |
|
hmArcClientAdminStatus |
1.3.6.1.4.1.248.14.5.7.3.1 |
The administratively desired status of the ARC client.
enabled(1): ARC client is active, the device can be configured automatically and can return
a status on a topology check.
disabled(2): ARC client is inactive, neither checking nor automatic configuring can be done.
checkOnly(3): The ARC client returns a status on a topology check but it's not possible
to configure the device automatically. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enabled(1), disabled(2), checkOnly(3) |
|
hmArcClientManagerDeviceMac |
1.3.6.1.4.1.248.14.5.7.4.1 |
The MAC address of the ARC manager that last checked or configured the device. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(6) |
|
hmArcClientManagerDeviceIp |
1.3.6.1.4.1.248.14.5.7.4.2 |
The IP address of the ARC manager that last checked or configured the device. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
hmArcClientPrimGroupID |
1.3.6.1.4.1.248.14.5.7.4.3 |
Unique index to identify the slot number of
the to be configured primary link port. This value is never
greater than hmSysGroupCapacity. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
hmArcClientPrimIfIndex |
1.3.6.1.4.1.248.14.5.7.4.4 |
Interface index of the to be configured primary link. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
hmArcClientRedGroupID |
1.3.6.1.4.1.248.14.5.7.4.5 |
Unique index to identify the slot number of
the to be configured redundant link port. This value is never
greater than hmSysGroupCapacity. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
hmArcClientRedIfIndex |
1.3.6.1.4.1.248.14.5.7.4.6 |
Interface index of the to be configured redundant link. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|