HP-ICF-IPCONFIG

File: HP-ICF-IPCONFIG.mib (45213 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
INET-ADDRESS-MIB IF-MIB HP-ICF-OID
IP-MIB TUNNEL-MIB

Imported symbols

OBJECT-TYPE MODULE-IDENTITY Unsigned32
Integer32 RowStatus MODULE-COMPLIANCE
OBJECT-GROUP InetAddress InetAddressType
InetAddressPrefixLength InetAddressIPv4 InetPortNumber
ifIndex hpicfCommon ipv4InterfaceEntry
ipv6InterfaceEntry IpAddressOriginTC IpAddressStatusTC
ipNetToPhysicalEntry tunnelInetConfigEntry

Defined Types

HpicfIpAddressEntry  
SEQUENCE    
  hpicfIpAddressAddrType InetAddressType
  hpicfIpAddressAddr InetAddress
  hpicfIpAddressPrefixLength InetAddressPrefixLength
  hpicfIpAddressType INTEGER
  hpicfIpAddressRowStatus RowStatus
  hpicfIpAddressExtendedType INTEGER

HpicfSwitchIpAddressEntry  
SEQUENCE    
  hpicfSwitchIpAddressAddrType InetAddressType
  hpicfSwitchIpAddressAddr InetAddress
  hpicfSwitchIpAddressPrefixLength InetAddressPrefixLength
  hpicfSwitchIpAddressType INTEGER
  hpicfSwitchIpAddressOrigin IpAddressOriginTC
  hpicfSwitchIpAddressStatus IpAddressStatusTC
  hpicfSwitchIpAddressPreferredLifetime Unsigned32
  hpicfSwitchIpAddressValidLifetime Unsigned32
  hpicfSwitchIpAddressExtendedType INTEGER

HpicfIpNetToPhysicalEntry  
SEQUENCE    
  hpicfIpNetToPhysicalPort Integer32

HpicfIpv4InterfaceEntry  
SEQUENCE    
  hpicfIpv4InterfaceDhcpEnable INTEGER
  hpicfIpv4InterfaceForwarding INTEGER
  hpicfIpv4InterfaceProxyArp INTEGER
  hpicfIpv4InterfaceLocalProxyArp INTEGER
  hpicfIpv4InterfaceBootpGateway InetAddressIPv4
  hpicfIpv4InterfaceDirectedBcastFwd INTEGER

HpicfIpv6InterfaceEntry  
SEQUENCE    
  hpicfIpv6InterfaceDhcpMode INTEGER
  hpicfIpv6InterfaceManual INTEGER
  hpicfIpv6InterfaceAutoConfig INTEGER
  hpicfIpv6InterfaceDhcpRapidCommit INTEGER
  hpicfIpv6InterfaceDhcpRelay INTEGER
  hpicfIpv6InterfaceCfgEnableStatus INTEGER
  hpicfIpv6InterfaceDadAttempts Integer32
  hpicfIpv6InterfaceDadAttemptsMode INTEGER
  hpicfIpv6InterfaceReachableTime Unsigned32
  hpicfIpv6InterfaceRetransmitTime Unsigned32

HpicfUdpTunnelEntry  
SEQUENCE    
  hpicfUdpTunnelSrcPort InetPortNumber
  hpicfUdpTunnelMirrorSessionID Integer32
  hpicfUdpTunnelMirrorTruncate INTEGER

Defined Values

hpicfIpConfig 1.3.6.1.4.1.11.2.14.11.1.10
This MIB module describes objects for basic IP address configuration and interface configuration for devices in the HP Integrated Communication Facility product line.
MODULE-IDENTITY    

hpicfIpConfigObjects 1.3.6.1.4.1.11.2.14.11.1.10.1
OBJECT IDENTIFIER    

hpicfIpAddressObjects 1.3.6.1.4.1.11.2.14.11.1.10.1.1
OBJECT IDENTIFIER    

hpicfIpv4InterfaceObjects 1.3.6.1.4.1.11.2.14.11.1.10.1.2
OBJECT IDENTIFIER    

hpicfIpv6ConfigObjects 1.3.6.1.4.1.11.2.14.11.1.10.3
OBJECT IDENTIFIER    

hpicfIpv6GlobalConfigObjects 1.3.6.1.4.1.11.2.14.11.1.10.3.1
OBJECT IDENTIFIER    

hpicfIpv6NDObjects 1.3.6.1.4.1.11.2.14.11.1.10.3.1.1
OBJECT IDENTIFIER    

hpicfIpv6IcmpObjects 1.3.6.1.4.1.11.2.14.11.1.10.3.1.2
OBJECT IDENTIFIER    

hpicfIpv6InterfaceObjects 1.3.6.1.4.1.11.2.14.11.1.10.3.2
OBJECT IDENTIFIER    

hpicfIpAddressTable 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1
This table contains manually configured IPv4 and IPv6 addresses for each interface. An entry in this table may not exist in the active state unless all objects in the entry are consistent. In particular, the value of hpicfIpAddressPrefixLength.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HpicfIpAddressEntry

hpicfIpAddressEntry 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1
An entry in the hpicfIpAddressEntry contains a single manually configured IP address.
Status: current Access: not-accessible
OBJECT-TYPE    
  HpicfIpAddressEntry  

hpicfIpAddressAddrType 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.1
Type of IP address
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

hpicfIpAddressAddr 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.2
The IP address to which this entry's addressing information pertains. hpicfIpAddressAddr is always interpreted within the context of hpicfIpAddressAddrType.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

hpicfIpAddressPrefixLength 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.3
The prefix length associated with IP address.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressPrefixLength  

hpicfIpAddressType 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.4
IP address type. For V4 addresses the value will be unicast.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER unicast(1), anycast(2)  

hpicfIpAddressRowStatus 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.5
The status of the IP address entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hpicfIpAddressExtendedType 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.6
IP address type. For V4 addresses the value will be none. For V6 address it can be eui64 and linkLocal also.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(0), eui64(1), linkLocal(2)  

hpicfSwitchIpAddressTable 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2
This read only table contains IPV4 and/or IPV6 addresses for each interface. These IP Addresses are either manually configured or obtained by a dynamic method (such as DHCP). This table will hold all manually configured IP Addresses that exist in hpicfIpAddressTable except for those entries that are not in active state (hpicfIpAddressRowStatus).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HpicfSwitchIpAddressEntry

hpicfSwitchIpAddressEntry 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1
An entry in the hpicfSwitchIpAddressEntry contains a single IP address.
Status: current Access: not-accessible
OBJECT-TYPE    
  HpicfSwitchIpAddressEntry  

hpicfSwitchIpAddressAddrType 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.1
Type of IP address.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

hpicfSwitchIpAddressAddr 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.2
The IP address to which this entry's addressing information pertains. hpicfSwitchIpAddressAddr is always interpreted within the context of hpicfSwitchIpAddressAddrType.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

hpicfSwitchIpAddressPrefixLength 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.3
The prefix length associated with IP address.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressPrefixLength  

hpicfSwitchIpAddressType 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.4
IP address type. For V4 addresses the value will be unicast.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unicast(1), anycast(2)  

hpicfSwitchIpAddressOrigin 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.5
The origin of the address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddressOriginTC  

hpicfSwitchIpAddressStatus 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.6
The status of the address, describing if the address can be used for communication. In the absence of other information, an IPv4 address is always preferred(1).
Status: current Access: read-only
OBJECT-TYPE    
  IpAddressStatusTC  

hpicfSwitchIpAddressPreferredLifetime 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.7
The remaining length of time in seconds that this address will continue to be preferred, i.e. time until deprecation. A value of 4,294,967,295 represents infinity. The address generated from a deprecated address should no longer be used as a source address in new communications, but packets received on such an interface are processed as expected. The default for IPv4 addresses is 4,294,967,295 (infinity).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hpicfSwitchIpAddressValidLifetime 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.8
The remaining length of time, in seconds, that this address will continue to be valid, i.e. time until invalidation. A value of 4,294,967,295 represents infinity. The address generated from an invalidated address should not appear as the destination or source address of a packet. The default for IPv4 addresses is 4,294,967,295 (infinity).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hpicfSwitchIpAddressExtendedType 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.9
IP address type. For V4 addresses the value will be none. For V6 address it can be eui64 and linkLocal also.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), eui64(1), linkLocal(2)  

hpicfIpNetToPhysicalTable 1.3.6.1.4.1.11.2.14.11.1.10.1.1.3
This table augments ipNeTtoPhysicalTable
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HpicfIpNetToPhysicalEntry

hpicfIpNetToPhysicalEntry 1.3.6.1.4.1.11.2.14.11.1.10.1.1.3.1
This table augments ipNeTtoPhysicalTable
Status: current Access: not-accessible
OBJECT-TYPE    
  HpicfIpNetToPhysicalEntry  

hpicfIpNetToPhysicalPort 1.3.6.1.4.1.11.2.14.11.1.10.1.1.3.1.1
This object gives the port through which the physical address was learnt
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hpicfIpNetToPhysicalTableClear 1.3.6.1.4.1.11.2.14.11.1.10.1.1.4
This provides the clear options for hpicfIpNetToPhysicalTable. A value of 2 is to clear arp table. A value of 3 is to clear the ipv6 neighbor table. A get returns 'unknown' always.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unknown(1), ipv4(2), ipv6(3)  

hpicfIpv4InterfaceTable 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1
This table contains per-interface IPV4 configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HpicfIpv4InterfaceEntry

hpicfIpv4InterfaceEntry 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1
An entry in the hpicfIpv4InterfaceEntry contains IPV4 interface specific configuration information. This table is indexed by ipv4InterfaceIfIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HpicfIpv4InterfaceEntry  

hpicfIpv4InterfaceDhcpEnable 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.1
Changing this flag to 'full' will clear any existing IP address configuration for this interface and will cause the device to use a dynamic method (e.g. DHCP) to obtain its IP configuration and other configuration parameter (such as gateway, time of day, etc...) for this interface. Setting this flag to 'inform' will allow manual IP address configuration and yet permit other configuration parameters (such as gateway, time of day, etc...) to be obtained from a DHCP server. Setting this flag to 'off' will allow manual IP configuration but disallow any DHCP configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER full(1), off(2), inform(3)  

hpicfIpv4InterfaceForwarding 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.2
This flag indicates whether this interface is forwarding the datagrams that were not addressed to this interface. Setting this flag to 'enabled' (the default) results in forwarding the datagrams that were not addressed to this interface. Setting this flag to 'disabled' results in ignoring datagrams that were not addressed to this entity.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hpicfIpv4InterfaceProxyArp 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.3
Enables/disables ARP proxy on the interface. If set to 'enabled', the switch will respond on ARP request for IP addresses from other subnets. If set to disabled (the default), the switch will not respond on ARP request for IP addresses from other subnets.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hpicfIpv4InterfaceLocalProxyArp 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.4
Enables/disables local ARP proxy on the interface. If set to 'enabled', the switch will respond on ARP request for IP addresses within the local subnet. If set to disabled (the default), the switch will not respond on ARP request for IP addresses within the local subnet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hpicfIpv4InterfaceBootpGateway 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.5
This entry will specify the IP address to be used as the BOOTP gateway for this interface. Note that this IP address will be used as the BOOTP gateway only when it is configured as an IP address on this interface. Otherwise, the lowest IP address configured on the interface will be used as the gateway address.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressIPv4  

hpicfIpv4InterfaceDirectedBcastFwd 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.6
Enable/disable directed-broadcast forwarding on this interface. When set to default, the global hpicfDBroadcastFwdEnable setting is used. When set to enable, directed-broadcasts are enabled irrespective of the global setting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), default(2)  

hpicfIpv6NDDadAttempts 1.3.6.1.4.1.11.2.14.11.1.10.3.1.1.1
The value in this object indicates the maximum number of neighbor solicitation requests that will be sent while performing duplicate address detection.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hpicfIpv6IcmpErrorInterval 1.3.6.1.4.1.11.2.14.11.1.10.3.1.2.1
The value in this object indicates the error interval in which the token bucket algorithm places one token in the bucket for ICMPV6 rate limiting.Each token represents the right to send one ICMP error message. Each time an error is sent, it takes a token from the bucket. ICMP will not be allowed to originate an error message if the bucket is empty.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hpicfIpv6IcmpBucketsize 1.3.6.1.4.1.11.2.14.11.1.10.3.1.2.2
The value in this object indicates the maximum number of tokens that can be in the bucket.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hpicfIpv6InterfaceTable 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1
This table contains per-interface IPV6 configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HpicfIpv6InterfaceEntry

hpicfIpv6InterfaceEntry 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1
An entry in the hpicfIpv6InterfaceEntry contains IPV6 interface specific configuration information. This table is indexed by ipv6InterfaceIfIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HpicfIpv6InterfaceEntry  

hpicfIpv6InterfaceDhcpMode 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.1
Setting this flag to 'dhcpFull' will clear any existing IP address configuration for this interface and will cause the device to use a dynamic method (e.g. DHCP) to obtain its IP configuration and other configuration parameter (such as gateway, time of day, etc...) for this interface. Setting this flag to 'dhcpInform' will allow manual IP address configuration and yet permit other configuration parameters (such as gateway, time of day, etc...) to be obtained from a DHCP server. Setting this flag to 'disabled' will not allow any of the above mentioned two configuration, but interface can have link-local, auto-config and manual ip-address.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), dhcpFull(1), dhcpInform(2)  

hpicfIpv6InterfaceManual 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.2
Setting this flag to 'enabled' will allow manual IP address configuration but disallow any DHCP configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hpicfIpv6InterfaceAutoConfig 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.3
Setting this flag to 'enabled' will allow host to configure automatically from default router. There may be multiple routers and in that scenario switch will add the addresses from all these routers
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hpicfIpv6InterfaceDhcpRapidCommit 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.4
Setting this flag to 'enabled' will allow the host to get address and configuration information from the dhcp server rapidly. This flag can be enabled only if the hpicfIpv6InterfaceDhcpMode object is set as dhcpFull. By default this flag is set to disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hpicfIpv6InterfaceDhcpRelay 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.5
This flag indicates whether this interface is dhcp-relay enabled. By default this flag is set to disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hpicfIpv6InterfaceCfgEnableStatus 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.6
The indication of whether IPv6 is enabled (up) or disabled (down) on this interface. Setting this object to up(1) will enable ipv6 for the given interface.Setting this object to down(2) will disable the ipv6 for the interface only if hpicfIpv6InterfaceDhcpMode, hpicfIpv6InterfaceManual and hpicfIpv6InterfaceAutoConfig are disabled.A get on this object reflects the data saved in a non-volatile storage. Note:To get the current ipv6 status for an interface refer to ipv6InterfaceEnableStatus.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

hpicfIpv6InterfaceDadAttempts 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.7
This object indicates the maximum number of neighbor solicitation requests that will be sent while performing duplicate address detection for this interface. Note: hpicfIpv6NDDadAttempts object's value will be in use for dad attempts for this interface when hpicfIpv6InterfaceDadAttemptsMode is 'global'.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hpicfIpv6InterfaceDadAttemptsMode 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.8
This object indicates whether the value in hpicfIpv6NDDadAttempts is in use or the value in hpicfIpv6InterfaceDadAttempts is in use for an entry in this table while performing duplicate address detection. A set to 'global' means: - hpicfIpv6NDDadAttempts value will be used for dad attempts. A set to 'perInterface' means: - hpicfIpv6InterfaceDadAttempts value will be used for dad attempts.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER global(1), perInterface(2)  

hpicfIpv6InterfaceReachableTime 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.9
The time a neighbor is considered reachable after receiving a reachability confirmation.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

hpicfIpv6InterfaceRetransmitTime 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.10
The time between retransmissions of Neighbor Solicitation messages to a neighbor when resolving the address or when probing the reachability of a neighbor.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

hpicfUdpTunnelTable 1.3.6.1.4.1.11.2.14.11.1.10.1.2.3
This table contains per interface IPV4 Udp encapsulated tunnel specific configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HpicfUdpTunnelEntry

hpicfUdpTunnelEntry 1.3.6.1.4.1.11.2.14.11.1.10.1.2.3.1
An entry in the hpicfUdpTunnelEntry contains Udp encapsulated tunnel specific configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  HpicfUdpTunnelEntry  

hpicfUdpTunnelSrcPort 1.3.6.1.4.1.11.2.14.11.1.10.1.2.3.1.1
This variable is valid only for the remote mirroring source or destination switch. The value will be ignored otherwise. A value of 0 means that the UDP port is irrelevant for the tunnel type. If this value is non-zero it must be duplicated in the tunnelInetConfigID value (this will ensure that a given UDP port can only be associated once with a given tunnelInetConfigAddressType, tunnelInetConfigLocalAddress, tunnelInetConfigRemoteAddress, tunnelInetConfigEncapsMethod combination).
Status: current Access: read-create
OBJECT-TYPE    
  InetPortNumber  

hpicfUdpTunnelMirrorSessionID 1.3.6.1.4.1.11.2.14.11.1.10.1.2.3.1.2
This variable is valid only for a remote mirroring switch which interfaces with the source end of the tunnel. The value will be ignored otherwise. A value of 0 means that the mirror session ID is irrelevant for the tunnel type.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..512  

hpicfUdpTunnelMirrorTruncate 1.3.6.1.4.1.11.2.14.11.1.10.1.2.3.1.3
Enables/disables truncation for remote mirroring.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hpicfIpConfigConformance 1.3.6.1.4.1.11.2.14.11.1.10.2
OBJECT IDENTIFIER    

hpicfIpConfigCompliances 1.3.6.1.4.1.11.2.14.11.1.10.2.1
OBJECT IDENTIFIER    

hpicfIpConfigGroups 1.3.6.1.4.1.11.2.14.11.1.10.2.2
OBJECT IDENTIFIER    

hpicfIpConfigCompliance 1.3.6.1.4.1.11.2.14.11.1.10.2.1.1
A compliance statement for HP Routing switches with IP Configuration
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

hpicfIpConfigCompliance2 1.3.6.1.4.1.11.2.14.11.1.10.2.1.2
A compliance statement for HP Routing switches with IP Configuration
Status: current Access: read-write
MODULE-COMPLIANCE    

hpicfIpConfigCompliance4 1.3.6.1.4.1.11.2.14.11.1.10.2.1.4
A compliance statement for HP Routing switches with IP Configuration
Status: current Access: read-write
MODULE-COMPLIANCE    

hpicfIpConfigCompliance5 1.3.6.1.4.1.11.2.14.11.1.10.2.1.5
A compliance statement for HP Routing switches with IP Configuration
Status: current Access: read-write
MODULE-COMPLIANCE    

hpicfIpConfigCompliance6 1.3.6.1.4.1.11.2.14.11.1.10.2.1.6
A compliance statement for HP Routing switches with IP Configuration
Status: current Access: read-write
MODULE-COMPLIANCE    

hpicfIpConfigCompliance7 1.3.6.1.4.1.11.2.14.11.1.10.2.1.7
A compliance statement for HP Routing switches with IP Configuration
Status: current Access: read-write
MODULE-COMPLIANCE    

hpicfIpConfigCompliance8 1.3.6.1.4.1.11.2.14.11.1.10.2.1.8
A compliance statement for HP Routing switches with IP Configuration
Status: current Access: read-write
MODULE-COMPLIANCE    

hpicfIpConfigCompliance9 1.3.6.1.4.1.11.2.14.11.1.10.2.1.9
A compliance statement for HP Routing switches with IP Configuration
Status: current Access: read-write
MODULE-COMPLIANCE    

hpicfIpAddressTableGroup 1.3.6.1.4.1.11.2.14.11.1.10.2.2.1
A Collection of objects allowing configuration of an IP address for an interface.
Status: current Access: read-write
OBJECT-GROUP    

hpicfSwitchIpAddressTableGroup 1.3.6.1.4.1.11.2.14.11.1.10.2.2.2
A Collection of objects providing interfaces addressing information.
Status: current Access: read-write
OBJECT-GROUP    

hpicfIpv4InterfaceTableGroup 1.3.6.1.4.1.11.2.14.11.1.10.2.2.3
Deprecated - see hpicfIpv4InterfaceTableGroup2
Status: deprecated Access: read-write
OBJECT-GROUP    

hpicfUdpTunnelTableGroup 1.3.6.1.4.1.11.2.14.11.1.10.2.2.4
A Collection of objects that allows IPV4 interface configuration for remote mirroring
Status: current Access: read-write
OBJECT-GROUP    

hpicfIpv6InterfaceTableGroup 1.3.6.1.4.1.11.2.14.11.1.10.2.2.5
A Collection of objects that allows IPV6 interface configuration
Status: current Access: read-write
OBJECT-GROUP    

hpicfIpv4InterfaceTableGroup2 1.3.6.1.4.1.11.2.14.11.1.10.2.2.6
A Collection of objects that allows IPV4 interface configuration
Status: current Access: read-write
OBJECT-GROUP    

hpicfIpv6DadAttemptsGroup 1.3.6.1.4.1.11.2.14.11.1.10.2.2.7
A collection of objects that allows the number of DAD Attempts to be configured globally and also on a per interface basis.
Status: current Access: read-write
OBJECT-GROUP    

hpicfIpv6IcmpGroup 1.3.6.1.4.1.11.2.14.11.1.10.2.2.8
Objects provided for the ipv6 icmp configuration.
Status: current Access: read-write
OBJECT-GROUP    

hpicfIpNetToPhysicalTableGroup 1.3.6.1.4.1.11.2.14.11.1.10.2.2.9
Objects provided for the clear options in the device.
Status: current Access: read-write
OBJECT-GROUP    

hpicfUdpTunnelMirrorGroup 1.3.6.1.4.1.11.2.14.11.1.10.2.2.10
An object that enables or disables truncation for remote mirroring.
Status: current Access: read-write
OBJECT-GROUP    

hpicfIpv6NDGroup 1.3.6.1.4.1.11.2.14.11.1.10.2.2.11
Objects provided for configuration of ipv6 ND parameters
Status: current Access: read-write
OBJECT-GROUP    

hpicfIpv4InterfaceTableGroup3 1.3.6.1.4.1.11.2.14.11.1.10.2.2.12
A Collection of objects that allows IPV4 interface configuration
Status: current Access: read-write
OBJECT-GROUP