HPN-ICF-ENTITY-EXT-MIB

File: HPN-ICF-ENTITY-EXT-MIB.mib (69834 bytes)

Imported modules

HPN-ICF-OID-MIB SNMPv2-CONF SNMPv2-SMI
SNMPv2-TC SNMP-FRAMEWORK-MIB ENTITY-MIB
HCNUM-TC

Imported symbols

hpnicfCommon OBJECT-GROUP MODULE-COMPLIANCE
NOTIFICATION-GROUP OBJECT-TYPE MODULE-IDENTITY
NOTIFICATION-TYPE Integer32 Unsigned32
Gauge32 TimeTicks TEXTUAL-CONVENTION
MacAddress DateAndTime DisplayString
SnmpAdminString entPhysicalIndex entPhysicalName
entPhysicalDescr CounterBasedGauge64

Defined Types

HpnicfAdminState  
The administrative state for this object, and it is possible to set the state when needed. A value of locked means the resource is administratively prohibited from use. A value of shuttingDown means that usage is administratively limited to current instances of use. A value of unlocked means the resource is not administratively prohibited from use.
TEXTUAL-CONVENTION    
  INTEGER notSupported(1), locked(2), shuttingDown(3), unlocked(4)  

HpnicfOperState  
Represents the possible values of operational states. A value of disabled means the resource is totally inoperable. A value of enabled means the resource is partially or fully operable.
TEXTUAL-CONVENTION    
  INTEGER notSupported(1), disabled(2), enabled(3), dangerous(4)  

HpnicfAlarmStatus  
Represents the possible values of alarm status. When no bits of this attribute are set, then none of the status conditions described below are present. When the value of under repair is set, the resource is currently being repaired. When the value of critical is set, one or more critical alarms are active against the resource. When the value of major is set, one or more major alarms are active against the resource. When the value of minor is set, one or more minor alarms are active against the resource. When the value of warning is set, one or more warning alarms are active against the resource. When the value of indeterminate is set, one or more alarms of indeterminate severity are active against the resource. When the value of alarm outstanding is set, one or more alarms is active against the resource. The fault may or may not be disabling.
TEXTUAL-CONVENTION    
  BITS notSupported(0), underRepair(1), critical(2), major(3), minor(4), alarmOutstanding(5), warning(6), indeterminate(7)  

HpnicfStandbyStatus  
Represents the possible values of standby status. A value of hotStandby means the resource is not providing service, but is will be immediately able to take over the role of the resource to be backed-up, without the need for initialization activity, and will contain the same information as the resource to be backed up. A value of coldStandy means that the resource is to back-up another resource, but will not be immediately able to take over the role of a resource to be backed up, and will require some initialization activity. A value of providingService means the resource is providing service.
TEXTUAL-CONVENTION    
  INTEGER notSupported(1), hotStandby(2), coldStandby(3), providingService(4)  

HpnicfEntityExtStateEntry  
SEQUENCE    
  hpnicfEntityExtPhysicalIndex Integer32
  hpnicfEntityExtAdminStatus HpnicfAdminState
  hpnicfEntityExtOperStatus HpnicfOperState
  hpnicfEntityExtStandbyStatus HpnicfStandbyStatus
  hpnicfEntityExtAlarmLight HpnicfAlarmStatus
  hpnicfEntityExtCpuUsage Integer32
  hpnicfEntityExtCpuUsageThreshold Integer32
  hpnicfEntityExtMemUsage Integer32
  hpnicfEntityExtMemUsageThreshold Integer32
  hpnicfEntityExtMemSize Unsigned32
  hpnicfEntityExtUpTime Integer32
  hpnicfEntityExtTemperature Integer32
  hpnicfEntityExtTemperatureThreshold Integer32
  hpnicfEntityExtVoltage Integer32
  hpnicfEntityExtVoltageLowThreshold Integer32
  hpnicfEntityExtVoltageHighThreshold Integer32
  hpnicfEntityExtCriticalTemperatureThreshold Integer32
  hpnicfEntityExtMacAddress MacAddress
  hpnicfEntityExtErrorStatus INTEGER
  hpnicfEntityExtCpuMaxUsage Integer32
  hpnicfEntityExtLowerTemperatureThreshold Integer32
  hpnicfEntityExtShutdownTemperatureThreshold Integer32
  hpnicfEntityExtPhyMemSize Unsigned32
  hpnicfEntityExtPhyCpuFrequency Integer32
  hpnicfEntityExtFirstUsedDate DateAndTime
  hpnicfEntityExtCpuAvgUsage Integer32
  hpnicfEntityExtMemAvgUsage Integer32
  hpnicfEntityExtMemType OCTET STRING
  hpnicfEntityExtCriticalLowerTemperatureThreshold Integer32
  hpnicfEntityExtShutdownLowerTemperatureThreshold Integer32
  hpnicfEntityExtCpuUsageRecoverThreshold Integer32
  hpnicfEntityExtMemSizeRev CounterBasedGauge64
  hpnicfEntityExtCpuUsageIn1Minute Integer32
  hpnicfEntityExtCpuUsageIn5Minutes Integer32

HpnicfEntityExtManuEntry  
SEQUENCE    
  hpnicfEntityExtManuPhysicalIndex Integer32
  hpnicfEntityExtManuSerialNum SnmpAdminString
  hpnicfEntityExtManuBuildInfo SnmpAdminString
  hpnicfEntityExtManuBOM SnmpAdminString
  hpnicfEntityExtMacAddressCount Unsigned32

HpnicfEntityExtPowerEntry  
SEQUENCE    
  hpnicfEntityExtPowerPhysicalIndex Integer32
  hpnicfEntityExtNominalPower Gauge32
  hpnicfEntityExtCurrentPower Gauge32
  hpnicfEntityExtAveragePower Integer32
  hpnicfEntityExtPeakPower Integer32

HpnicfProcessEntry  
SEQUENCE    
  hpnicfProcessID Unsigned32
  hpnicfProcessName DisplayString
  hpnicfProcessUtil5Min Unsigned32

HpnicfEntityExtVoltageEntry  
SEQUENCE    
  hpnicfEntityExtCurrentVoltage Integer32
  hpnicfEntityExtNominalVoltage Integer32
  hpnicfEntityExtVoltageState INTEGER
  hpnicfEntityExtVoltageMajorLowThreshold Integer32
  hpnicfEntityExtVoltageFatalLowThreshold Integer32
  hpnicfEntityExtVoltageMajorHighThreshold Integer32
  hpnicfEntityExtVoltageFatalHighThreshold Integer32

Defined Values

hpnicfEntityExtend 1.3.6.1.4.1.11.2.14.11.15.2.6
The private MIB file includes the general extent information of the device.
MODULE-IDENTITY    

hpnicfEntityExtObjects 1.3.6.1.4.1.11.2.14.11.15.2.6.1
OBJECT IDENTIFIER    

hpnicfEntityExtState 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1
OBJECT IDENTIFIER    

hpnicfEntityExtStateTable 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1
This table contains one row per physical entity, There is always at least one row for an 'overall' physical entity. The information in each row may be not include all the object in this table, because of the entity need not some of the information here.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HpnicfEntityExtStateEntry

hpnicfEntityExtStateEntry 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1
The information about a particular physical entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  HpnicfEntityExtStateEntry  

hpnicfEntityExtPhysicalIndex 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.1
The index of hpnicfEntityExtStateTable. This index is identical to entPhysicalIndex in ENTITY-MIB
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtAdminStatus 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.2
The administrative state for this object.
Status: current Access: read-write
OBJECT-TYPE    
  HpnicfAdminState  

hpnicfEntityExtOperStatus 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.3
The operate state for this object.
Status: current Access: read-only
OBJECT-TYPE    
  HpnicfOperState  

hpnicfEntityExtStandbyStatus 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.4
This object is used for monitoring standby status. Not all entities support this object.
Status: current Access: read-only
OBJECT-TYPE    
  HpnicfStandbyStatus  

hpnicfEntityExtAlarmLight 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.5
The alarm status for this entity. It does not include the severity of alarms raised on child components. In this condition, there will be a alarm light on the entity, the object should have the same status with it.
Status: current Access: read-only
OBJECT-TYPE    
  HpnicfAlarmStatus  

hpnicfEntityExtCpuUsage 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.6
The CPU usage for this entity. Generally, the overall CPU usage on the entity is calculated, independent of the number of CPUs on the entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hpnicfEntityExtCpuUsageThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.7
The threshold for the CPU usage. When the CPU usage exceeds the threshold, a notification will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

hpnicfEntityExtMemUsage 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.8
The memory usage for the entity. This object indicates what percent of memory are used.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hpnicfEntityExtMemUsageThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.9
The threshold for the Memory usage, When the memory usage exceeds the threshold, a notification will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

hpnicfEntityExtMemSize 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.10
The size of memory for the entity. If the amount of memory exceeds 4,294,967,295 bytes, the value remains 4,294,967,295 bytes.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hpnicfEntityExtUpTime 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.11
The uptime for the entity. The meaning of uptime is when the entity is up, and the value of the object will add 1 seconds while the entity is running.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtTemperature 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.12
The temperature for the entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtTemperatureThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.13
The threshold for the temperature. When the temperature exceeds the threshold, a notification will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtVoltage 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.14
The voltage for the entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtVoltageLowThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.15
The low-threshold for the voltage. When voltage is lower than low-threshold, a notification will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtVoltageHighThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.16
The high-threshold for the voltage. When voltage greater than high-threshold, a notification will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtCriticalTemperatureThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.17
The threshold for the critical Temperature. When temperature exceeds the critical temperature, a notification will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtMacAddress 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.18
MAC Address of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

hpnicfEntityExtErrorStatus 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.19
Indicate the error state of this entity object. Now it only supports Port, general power supply, RPS power supply and board/Subcard. It may have one of these values. The following four values can be used for all kinds of entities. notSupported(1) means this entity cannot support this function. normal(2) means the statement of this entity is normal. for ports, it doesn't differentiate 10M/s, 100M/s, 1000M/s, duplex and half-duplex. For fan, power supply and board-Subcard, it means their states are normal. postFailure(3) means the entity fails to POST. entityAbsent(4) means the entity is absent now. The following values is depended on the entity. For Port entities, it may have the following values. If its POST is failure, then the value of the instance will be postFailure(3), otherwise the value will be normal(2). If enable power supply over Ethernet on this port is failure, the value of this instance will be poeError(11), otherwise it will be normal(2). For stack port, if it connects to another stack port normally, and these two units merge into one stack, then the value of this instance will be normal(2). If something wrong occurs and the unit cannot merge into stack, the value of this instance will be stackPortFailed(23). If the stack port forms resilient daisy chain with another stack port on the other unit, the value of this instance will be stackPortBlocked(22). For SFP ports, if it fail to receive, the value of this instance will be sfpRecvError(31), if it fail to send, the value is sfpSendError(32), if it fail to send and receive, the value is sfpBothError(33), otherwise it will be normal(2). fanError(41) means that the fan stops working. psuError(51) means that the Power Supply Unit is in the state of fault. rpsError(61) means the RPS is in the state of fault. moduleFaulty(71) means the Module is in the state of fault. sensorError(81) means the sensor is in the state of fault. hardwareFaulty(91) means the hardware of specified entity is in the state of fault. NMS must be compatible with the states which may be added in the future.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(1), normal(2), postFailure(3), entityAbsent(4), poeError(11), stackError(21), stackPortBlocked(22), stackPortFailed(23), sfpRecvError(31), sfpSendError(32), sfpBothError(33), fanError(41), psuError(51), rpsError(61), moduleFaulty(71), sensorError(81), hardwareFaulty(91)  

hpnicfEntityExtCpuMaxUsage 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.20
The maximal CPU usage for the entity in the period of time.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hpnicfEntityExtLowerTemperatureThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.21
The threshold for the lower Temperature. When temperature runs under the threshold, a notification will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtShutdownTemperatureThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.22
The threshold for the shutdown Temperature. When temperature exceeds the threshold, a notification will be sent and the entity will be shutdown.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtPhyMemSize 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.23
The memory size of entity. This is the physical attribute of entity.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hpnicfEntityExtPhyCpuFrequency 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.24
The CPU frequency of entity. Unit of measure is MHZ.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtFirstUsedDate 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.25
The first used date of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime Size(8)  

hpnicfEntityExtCpuAvgUsage 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.26
The average CPU usage for the entity in a period of time.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hpnicfEntityExtMemAvgUsage 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.27
The average memory usage for the entity in a period of time.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hpnicfEntityExtMemType 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.28
The memory type of entity.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

hpnicfEntityExtCriticalLowerTemperatureThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.29
The threshold for the critical Temperature. When temperature exceeds the critical lower temperature, a notification will be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtShutdownLowerTemperatureThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.30
The threshold for the shutdown Temperature. When temperature exceeds the lower threshold, a notification will be sent and the entity will be shutdown.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtCpuUsageRecoverThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.31
The recover threshold for the CPU usage. When the CPU usage falls down to the threshold, a notification is sent. The hpnicfEntityExtCpuUsageRecoverThreshold must be less than or equal to the hpnicfEntityExtCpuUsageThreshold.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

hpnicfEntityExtMemSizeRev 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.32
Size of memory space for the entity. This node is used to replace hpnicfEntityExtMemSize.
Status: current Access: read-only
OBJECT-TYPE    
  CounterBasedGauge64  

hpnicfEntityExtCpuUsageIn1Minute 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.33
The CPU usage in last one minute for this entity. Generally, the overall CPU usage on the entity is calculated, independent of the number of CPUs on the entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hpnicfEntityExtCpuUsageIn5Minutes 1.3.6.1.4.1.11.2.14.11.15.2.6.1.1.1.1.34
The CPU usage in last five minutes for this entity. Generally, the overall CPU usage on the entity is calculated, independent of the number of CPUs on the entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hpnicfEntityExtManu 1.3.6.1.4.1.11.2.14.11.15.2.6.1.2
OBJECT IDENTIFIER    

hpnicfEntityExtManuTable 1.3.6.1.4.1.11.2.14.11.15.2.6.1.2.1
The table about device manufacture information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HpnicfEntityExtManuEntry

hpnicfEntityExtManuEntry 1.3.6.1.4.1.11.2.14.11.15.2.6.1.2.1.1
The device manufacture information about a particular physical entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  HpnicfEntityExtManuEntry  

hpnicfEntityExtManuPhysicalIndex 1.3.6.1.4.1.11.2.14.11.15.2.6.1.2.1.1.1
The index of hpnicfEntityExtManuTable. This index is identical to entPhysicalIndex in ENTITY-MIB.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 1..2147483647  

hpnicfEntityExtManuSerialNum 1.3.6.1.4.1.11.2.14.11.15.2.6.1.2.1.1.2
Manufacture serial number. The manufacture serial number of the entity such as chassis, module, and so on. It is got from the device when manufacturing. For low level box-device, the manufacture serial number is the device-number of System Control Board(SCB for short), it is written into the SCB directly; for middle level or high level frame-device, the manufacture serial number is the device-numbers of SCB and Service Board, because the SCB, Service Board and chassis are separate to sale and the device-number of chassis cannot be written into board.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hpnicfEntityExtManuBuildInfo 1.3.6.1.4.1.11.2.14.11.15.2.6.1.2.1.1.3
Device version information. The device version information of the entity such as chassis, module, and so on. It consists of software version information and hardware version information.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hpnicfEntityExtManuBOM 1.3.6.1.4.1.11.2.14.11.15.2.6.1.2.1.1.4
Device BOM code. The device BOM code of the entity such as chassis, module, and so on. It is the component code of ERP system, which can be disassembled from device-number.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

hpnicfEntityExtMacAddressCount 1.3.6.1.4.1.11.2.14.11.15.2.6.1.2.1.1.5
MAC address count. The count of MAC addresses of the entity, such as chassis, module, or port, and so on.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hpnicfEntityExtPower 1.3.6.1.4.1.11.2.14.11.15.2.6.1.3
OBJECT IDENTIFIER    

hpnicfEntityExtPowerTable 1.3.6.1.4.1.11.2.14.11.15.2.6.1.3.1
This table describes the power information of all the physical entity on the device, such as the fans, the subcards, the boards, etc.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HpnicfEntityExtPowerEntry

hpnicfEntityExtPowerEntry 1.3.6.1.4.1.11.2.14.11.15.2.6.1.3.1.1
The entity power information about a particular physical entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  HpnicfEntityExtPowerEntry  

hpnicfEntityExtPowerPhysicalIndex 1.3.6.1.4.1.11.2.14.11.15.2.6.1.3.1.1.1
The index of hpnicfEntityExtPowerTable. This index is identical to entPhysicalIndex in ENTITY-MIB.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 1..2147483647  

hpnicfEntityExtNominalPower 1.3.6.1.4.1.11.2.14.11.15.2.6.1.3.1.1.2
The nominal power of the entity expressed in milliWatts.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hpnicfEntityExtCurrentPower 1.3.6.1.4.1.11.2.14.11.15.2.6.1.3.1.1.3
The measured usage power of the entity expressed in milliWatts.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hpnicfEntityExtAveragePower 1.3.6.1.4.1.11.2.14.11.15.2.6.1.3.1.1.4
The average power consumed by the entity expressed in milliWatts. Writing a value of zero to this object resets its value to zero. Writing any other value to this object has no effect on its value and an error is returned.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtPeakPower 1.3.6.1.4.1.11.2.14.11.15.2.6.1.3.1.1.5
The peak power consumed by the entity expressed in milliWatts. Writing a value of zero to this object resets its value to zero. Writing any other value to this object has no effect on its value and an error is returned.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hpnicfProcessObjects 1.3.6.1.4.1.11.2.14.11.15.2.6.1.4
OBJECT IDENTIFIER    

hpnicfProcessTable 1.3.6.1.4.1.11.2.14.11.15.2.6.1.4.1
The Table describes the information about a particular process, namely a task.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HpnicfProcessEntry

hpnicfProcessEntry 1.3.6.1.4.1.11.2.14.11.15.2.6.1.4.1.1
The information about a particular process, namely a task.
Status: current Access: not-accessible
OBJECT-TYPE    
  HpnicfProcessEntry  

hpnicfProcessID 1.3.6.1.4.1.11.2.14.11.15.2.6.1.4.1.1.1
This object indicates the identifier of process, namely task ID in system.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hpnicfProcessName 1.3.6.1.4.1.11.2.14.11.15.2.6.1.4.1.1.2
This object indicates the process name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

hpnicfProcessUtil5Min 1.3.6.1.4.1.11.2.14.11.15.2.6.1.4.1.1.3
This object provides a general idea of how busy a process caused the processor to be over a 5 minute period. The ratio is calculated by the overall CPU usage caused by the process.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100  

hpnicfEntityExtVoltageObjects 1.3.6.1.4.1.11.2.14.11.15.2.6.1.5
OBJECT IDENTIFIER    

hpnicfEntityExtVoltageTable 1.3.6.1.4.1.11.2.14.11.15.2.6.1.5.1
The table describes the voltage information of the voltage sensor entities on the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HpnicfEntityExtVoltageEntry

hpnicfEntityExtVoltageEntry 1.3.6.1.4.1.11.2.14.11.15.2.6.1.5.1.1
The voltage information of the voltage sensor entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  HpnicfEntityExtVoltageEntry  

hpnicfEntityExtCurrentVoltage 1.3.6.1.4.1.11.2.14.11.15.2.6.1.5.1.1.1
The current voltage in millivolts of the voltage sensor entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtNominalVoltage 1.3.6.1.4.1.11.2.14.11.15.2.6.1.5.1.1.2
The nominal voltage in millivolts of the voltage sensor entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtVoltageState 1.3.6.1.4.1.11.2.14.11.15.2.6.1.5.1.1.3
The voltage state of the voltage sensor entity.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(0), low(1), tooLow(2), high(3), tooHigh(4)  

hpnicfEntityExtVoltageMajorLowThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.5.1.1.4
The low threshold for the voltage sensor entity. When the voltage is lower than the threshold, a notification will be sent.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtVoltageFatalLowThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.5.1.1.5
The fatal low voltage threshold for the voltage sensor entity. When the voltage is lower than the threshold, a notification will be sent.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtVoltageMajorHighThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.5.1.1.6
The high threshold for the voltage sensor entity. When the voltage is higher than the threshold, a notification will be sent.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtVoltageFatalHighThreshold 1.3.6.1.4.1.11.2.14.11.15.2.6.1.5.1.1.7
The fatal high threshold for the voltage sensor entity. When the voltage is higher than the threshold, a notification will be sent.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtTraps 1.3.6.1.4.1.11.2.14.11.15.2.6.2
OBJECT IDENTIFIER    

hpnicfEntityExtTrapsPrefix 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0
OBJECT IDENTIFIER    

hpnicfEntityExtTrapsInfor 1.3.6.1.4.1.11.2.14.11.15.2.6.2.1
OBJECT IDENTIFIER    

hpnicfEntityExtTemperatureThresholdNotification 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.1
The hpnicfEntityExtTemperatureThresholdNotification indicates the temperature exceeded the threshold. In this condition, user should check the status and the environment of the entity, sometimes it happens because of the failure of air-condition.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtVoltageLowThresholdNotification 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.2
The hpnicfEntityExtVoltageLowThresholdNotification indicates the voltage is lower than the threshold. If the voltage is lower too much than the entity needs, the entity will halt.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtVoltageHighThresholdNotification 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.3
The hpnicfEntityExtVoltageHighThresholdNotification indicates the voltage is higher than the threshold. If the voltage is higher too much than the entity needs, The entity may be damaged by the high voltage.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtCpuUsageThresholdNotfication 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.4
The hpnicfEntityExtCpuUsageThresholdNotfication indicates the entity is overloaded.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtMemUsageThresholdNotification 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.5
The hpnicfEntityExtMemUsageThresholdNotification indicates the entity is overloaded.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtOperEnabled 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.6
The trap indicates the entity is operable at present.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtOperDisabled 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.7
The trap indicates the entity is not operable at present.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtCriticalTemperatureThresholdNotification 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.8
The hpnicfEntityExtCriticalTemperatureThresholdNotification indicates the temperature exceeds the critical temperature. In this condition, user should check the status and the environment of the entity, sometimes it happens because of the failure of air-condition.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtSFPAlarmOn 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.9
The trap is generated when the SFP module fails or runs abnormally for some particular reason.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtSFPAlarmOff 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.10
The trap is generated when the SFP module restores to normal status.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtSFPPhony 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.11
This module is NOT sold by authorized manufacturer. The normal function of the device or assume the maintenance responsibility thereof will NOT be guaranteed. The trap is generated periodically after a phony module has been found.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityInsert 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.12
The trap is generated when a removable entity inserting to device.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityRemove 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.13
The trap is generated when a removable entity removing from device.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtForcedPowerOff 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.14
The trap indicates the entity is forced to power off.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtForcedPowerOn 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.15
The trap indicates the entity is forced to power on.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtFaultAlarmOn 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.16
The trap indicates a fault occurs on the specified entity.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtFaultAlarmOff 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.17
The trap indicates a fault disappears on the specified entity.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtResourceLack 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.18
The trap indicates that a kind of resource is not enough on the specified entity.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtResourceEnough 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.19
The trap indicates that the entity recovers from the status of no enough resource.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtTemperatureLower 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.20
The trap indicates the temperature of a specified entity is under the lower threshold. In this condition, user should check the status and the environment of the entity, sometimes it goes wrong for some reason.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtTemperatureTooUp 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.21
The trap indicates the temperature of a specified entity exceeded the shutdown threshold. In this condition, user should check the status and the environment of the entity, sometimes it goes wrong for some reason.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtTemperatureNormal 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.22
The trap indicates the temperature of a specified entity recover from abnormal status.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExternalAlarmOccur 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.23
The trap is generated when the monitored device connected to the specified entity fails.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExternalAlarmRecover 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.24
The trap is generated when the failed device connected to the specified entity returns to normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtCpuUsageThresholdRecover 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.25
The trap indicates the CPU usage descends the threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtMemUsageThresholdRecover 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.26
The trap indicates the memory usage descends the threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtMemAllocatedFailed 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.27
The trap indicates the memory allocated failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtECCParityAlarm 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.28
The trap indicates the ECC(Error Correction Code) parity error alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtCritLowerTempThresholdNotification 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.29
The hpnicfEntityExtCritLowerTempThresholdNotification indicates the temperature is lower than the threshold. If the temperature is lower too much than the entity needs, the entity will halt.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtTemperatureTooLow 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.30
The hpnicfEntityExtTemperatureTooLow indicates the temperature is lower than the threshold. If the temperature is lower too much than the entity needs, the entity halts now.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtFanDirectionNotPreferred 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.31
This trap indicates the specified fan's direction does not accord with preferred. The two parameters indicate the entity index and physical name of fan.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtFanDirectionNotAccord 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.32
This trap indicates the direction of fans does not accord with each other. The two parameters indicate the parent entity of the fans.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtSFPInvalid 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.33
The transceiver module is not compatible with the interface card. The authorized manufacturer therefore shall NOT guarantee the normal function of the transceiver. The transceiver module will be invalidated in days. Please replace it with a compatible one as soon as possible. The trap is generated periodically after a phony transceiver module has been found.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtSFPInvalidNow 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.34
This transceiver module is not compatible with the interface card. The authorized manufacturer therefore shall NOT guarantee the normal function of the transceiver. The trap is generated after a phony transceiver module has been found.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtMemUsageThresholdOverTrap 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.35
This trap indicates that the memory usage of the entity is overloaded. This trap is used to replace hpnicfEntityExtMemUsageThresholdNotification.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtMemUsageThresholdRecoverTrap 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.36
This trap indicates that the memory usage decreased below the threshold. This trap is used to replace hpnicfEntityExtMemUsageThresholdRecover.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtVoltageNormal 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.37
This trap indicates that the voltage recovers to normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtVoltageLower 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.38
This trap indicates that the voltage is lower than the low threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtVoltageTooLow 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.39
This trap indicates that the voltage is lower than the fatal low threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtVoltageHigher 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.40
This trap indicates that the voltage is higher than the high threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtVoltageTooHigh 1.3.6.1.4.1.11.2.14.11.15.2.6.2.0.41
This trap indicates that the voltage is higher than the fatal high threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

hpnicfEntityExtTrapDescription 1.3.6.1.4.1.11.2.14.11.15.2.6.2.1.1
The information of trap.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

hpnicfEntityExtECCParityAlarmStatus 1.3.6.1.4.1.11.2.14.11.15.2.6.2.1.2
ECC parity error.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER other(1), l1cache(2), l2cache(3), sdram(4), mac(5), tcam(6), ingressbuffer(7), egressbuffer(8), lpm(9), controlmemory(10)  

hpnicfEntityExtSFPInvalidInDays 1.3.6.1.4.1.11.2.14.11.15.2.6.2.1.3
The days when the transceiver module is still valid, but after those days, it will be invalidated.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

hpnicfEntityExtFirstTrapTime 1.3.6.1.4.1.11.2.14.11.15.2.6.2.1.4
Represents the first trap time.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  TimeTicks  

hpnicfEntityExtConformance 1.3.6.1.4.1.11.2.14.11.15.2.6.3
OBJECT IDENTIFIER    

hpnicfEntityExtCompliances 1.3.6.1.4.1.11.2.14.11.15.2.6.3.1
OBJECT IDENTIFIER    

hpnicfEntityExtCompliance 1.3.6.1.4.1.11.2.14.11.15.2.6.3.1.1
The compliance statement for systems supporting this MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

hpnicfEntityExtGroups 1.3.6.1.4.1.11.2.14.11.15.2.6.3.2
OBJECT IDENTIFIER    

hpnicfEntityExtGroup 1.3.6.1.4.1.11.2.14.11.15.2.6.3.2.1
Entity Extend group.
Status: current Access: read-only
OBJECT-GROUP    

hpnicfEntityExtNotificationGroup 1.3.6.1.4.1.11.2.14.11.15.2.6.3.2.2
Entity Extend Notification group.
Status: current Access: read-only
NOTIFICATION-GROUP    

hpnicfEntityExtManuGroup 1.3.6.1.4.1.11.2.14.11.15.2.6.3.2.3
Standard Device Manufacture Information group.
Status: current Access: read-only
OBJECT-GROUP    

hpnicfEntityExtPowerGroup 1.3.6.1.4.1.11.2.14.11.15.2.6.3.2.4
Standard Entity Power Information group.
Status: current Access: read-only
OBJECT-GROUP