HUAWEI-IF-EXT-MIB

File: HUAWEI-IF-EXT-MIB.mib (203641 bytes)

Imported modules

HUAWEI-MIB IF-MIB Q-BRIDGE-MIB
SNMPv2-CONF SNMPv2-SMI SNMPv2-MIB
SNMPv2-TC ATM-TC-MIB IP-MIB

Imported symbols

hwDatacomm ifIndex ifName
InterfaceIndex InterfaceIndexOrZero ifAdminStatus
ifOperStatus ifDescr VlanIdOrNone
PortList OBJECT-GROUP MODULE-COMPLIANCE
NOTIFICATION-GROUP IpAddress Integer32
Unsigned32 Counter64 OBJECT-TYPE
Gauge32 MODULE-IDENTITY NOTIFICATION-TYPE
sysUpTime RowStatus TruthValue
DisplayString PhysAddress TEXTUAL-CONVENTION
TimeStamp AtmVpIdentifier AtmVcIdentifier
ipAdEntNetMask

Defined Types

EnabledStatus  
A simple status value for the object.
TEXTUAL-CONVENTION    
  INTEGER enabled(1), disabled(2)  

SnmpPasswdString  
The password string
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..16)  

HWDirectionType  
The Direction Flux Limit apply on.
TEXTUAL-CONVENTION    
  INTEGER inbound(1), outbound(2)  

HwIpAddressType  
The type of IP address.
TEXTUAL-CONVENTION    
  INTEGER primary(1), sub(2)  

HwIFExtEntry  
SEQUENCE    
  hwIFExtIndex InterfaceIndex
  hwIFExtLayer INTEGER
  hwIFExtFrameType INTEGER
  hwIFExtFlowStatInterval Integer32
  hwIFExtFlushReceiveEnable EnabledStatus
  hwIFExtFlushVlanId VlanIdOrNone
  hwIFExtFlushPasswd SnmpPasswdString
  hwIFExtFlowStatus INTEGER
  hwIFExtMtu Integer32
  hwIFExtMacAddr PhysAddress
  hwIFExtBlockPriority Integer32
  hwIFExtMacShift INTEGER
  hwIFExtSuppressStatus INTEGER
  hwIFExtPoisonReverse EnabledStatus
  hwIFExtInputPktRate Gauge32
  hwIFExtInputHighPktRate Gauge32
  hwIFExtOutputPktRate Gauge32
  hwIFExtOutputHighPktRate Gauge32
  hwIFExtInputOctetRate Gauge32
  hwIFExtInputHighOctetRate Gauge32
  hwIFExtOutputOctetRate Gauge32
  hwIFExtOutputHighOctetRate Gauge32
  hwIFExtSwitchPortIndex Integer32
  hwIFExtSuppressStatusIPv6 INTEGER

HwLinkModeChangeAutoCreateIfEntry  
SEQUENCE    
  hwAutoIfIndex InterfaceIndex
  hwNewIfTimeslot BITS

HwIfIpEntry  
SEQUENCE    
  hwIpAdEntAddr IpAddress
  hwIpAdEntIfIndex Integer32
  hwIpAdEntNetMask IpAddress
  hwIpAdEntBcastAddr Integer32
  hwIpAdEntReasmMaxSize Integer32
  hwIpAdEntAddressType HwIpAddressType
  hwIfIpMethod INTEGER
  hwIpAdEntAddrStatus RowStatus

HwIfIpUnnumberedEntry  
SEQUENCE    
  hwUnnumberedIfIndex InterfaceIndex
  hwLendIfIndex InterfaceIndex
  hwLendIpAddr IpAddress
  hwLendIpAddrNetMask IpAddress
  hwUnnumberedRowStatus RowStatus

HwIfIpAddrEntry  
SEQUENCE    
  hwIfIpAddrEntIfIndex InterfaceIndex
  hwIfIpAddrEntAddr IpAddress
  hwIfIpAddrEntType INTEGER
  hwIfIpAddrEntPrefix IpAddress
  hwIfIpAddrEntOrigin INTEGER
  hwIfIpAddrEntStatus INTEGER
  hwIfIpAddrEntCreated TimeStamp
  hwIfIpAddrEntLastChanged TimeStamp
  hwIfIpAddrEntBcastAddr Integer32
  hwIfIpAddrEntReasmMaxSize Integer32
  hwIfIpAddrEntAddrType HwIpAddressType
  hwIfIpAddrEntVpn DisplayString

HwTrunkIfEntry  
SEQUENCE    
  hwTrunkIndex Integer32
  hwTrunkIfID Integer32
  hwTrunkIfType INTEGER
  hwTrunkIfIndex InterfaceIndex
  hwTrunkIfModel INTEGER
  hwTrunkIfBandWidthAffectLinkNum Integer32
  hwTrunkIfMinLinkNum Integer32
  hwTrunkIfRowStatus RowStatus
  hwTrunkIfWorkingMode INTEGER
  hwTrunkIfWorkingState INTEGER
  hwTrunkIfAutoRecover INTEGER
  hwTrunkIfPreemptEnable INTEGER
  hwTrunkIfPreemptDelay Integer32
  hwTrunkIfTimeoutReceive INTEGER
  hwTrunkIfFlushSendEnable INTEGER
  hwTrunkIfFlushVlanId Integer32
  hwTrunkIfFlushPasswd SnmpPasswdString
  hwTrunkIfForceSwitchEnable INTEGER
  hwTrunkIfStatReset INTEGER
  hwTrunkBandwidth Integer32
  hwTrunkIfArpSendSpeed Integer32
  hwTrunkIfLagSelectedPortStd INTEGER
  hwTrunkIfLagMaxActiveLinkNum Integer32
  hwTrunkETrunkPriority Integer32
  hwTrunkETrunkSysID PhysAddress
  hwTrunkETrunkPriorityReset INTEGER
  hwTrunkETrunkSysIDReset INTEGER
  hwTrunkLocalPrefMode INTEGER
  hwTrunkIfTrackVrrpVrid Integer32
  hwTrunkIfTrackVrrpIfIndex InterfaceIndex
  hwTrunkIfTrackVrrpReset INTEGER
  hwTrunkIfBackupPreemptEnable EnabledStatus
  hwTrunkIfBackupPreemptDelay Integer32
  hwTrunkIfCrcErrorSwitchEnable EnabledStatus
  hwTrunkIfLagTimeOut Integer32
  hwTrunkMemCount Integer32

HwTrunkMemEntry  
SEQUENCE    
  hwTrunkMemifIndex Integer32
  hwTrunkValidEntry INTEGER
  hwTrunkSelectStatus INTEGER
  hwTrunkLacpStatus EnabledStatus
  hwTrunkDeleteFlag EnabledStatus
  hwTrunkOperstatus INTEGER
  hwTrunkIsDefaultLagRecv TruthValue
  hwTrunkPortWeight Unsigned32
  hwTrunkPortStandby Unsigned32
  hwTrunkRowStatus RowStatus
  hwTrunkPortMaster INTEGER
  hwTrunkPortPriority Integer32
  hwTrunkPortStatReset INTEGER
  hwTrunkPortLacpMode INTEGER

HwIfEtherStatEntry  
SEQUENCE    
  hwIfEtherStatIfIndex InterfaceIndex
  hwIfEtherStatInPkts64Octets Counter64
  hwIfEtherStatInPkts65to127Octets Counter64
  hwIfEtherStatInPkts128to255Octets Counter64
  hwIfEtherStatInPkts256to511Octets Counter64
  hwIfEtherStatInPkts512to1023Octets Counter64
  hwIfEtherStatInPkts1024to1518Octets Counter64
  hwIfEtherStatInJumboPkts Counter64
  hwIfEtherStatInCRCPkts Counter64
  hwIfEtherStatInLongPkts Counter64
  hwIfEtherStatInJabberPkts Counter64
  hwIfEtherStatInFragmentPkts Counter64
  hwIfEtherStatInUnderSizePkts Counter64
  hwIfEtherStatInOverRunPkts Counter64
  hwIfEtherStatInPausePkts Counter64
  hwIfEtherStatOutJumboPkts Counter64
  hwIfEtherStatOutOverflowPkts Counter64
  hwIfEtherStatOutUnderRunPkts Counter64
  hwIfEtherStatOutPausePkts Counter64
  hwIfEthIfStatReset INTEGER
  hwIfEtherStatInDropEventPkts Counter64
  hwIfEtherStatInAlignmentPkts Counter64
  hwIfEtherStatInSymbolPkts Counter64
  hwIfEtherStatInIgnoredPkts Counter64
  hwIfEtherStatInFramePkts Counter64
  hwIfEtherStatOutCollisionPkts Counter64
  hwIfEtherStatOutDeferredPkts Counter64
  hwIfEtherStatOutLateCollisionPkts Counter64
  hwIfEtherStatOutExcessiveCollisionPkts Counter64
  hwIfEtherStatOutBufferPurgationPkts Counter64

HwIfSdhStatEntry  
SEQUENCE    
  hwIfSdhStatIfIndex InterfaceIndex
  hwIfSdhStatInCRCPkts Counter64
  hwIfSdhStatInShortPkts Counter64
  hwIfSdhStatInLongPkts Counter64
  hwIfSdhStatOutOverRunPkts Counter64
  hwIfSdhStatOutUnderRunPkts Counter64
  hwIfSdhIfStatReset INTEGER

HwIfAtmStatEntry  
SEQUENCE    
  hwIfAtmStatIfIndex InterfaceIndex
  hwIfAtmStatInGoodCells Counter64
  hwIfAtmStatInIdleCells Counter64
  hwIfAtmStatInCorrectedCells Counter64
  hwIfAtmStatInUncorrectedCells Counter64
  hwIfAtmStatOutGoodCells Counter64
  hwIfAtmStatOutIdleCells Counter64
  hwIfAtmIfStatReset INTEGER

HwIfMonitorThresholdEntry  
SEQUENCE    
  hwIfMonitorIndex InterfaceIndex
  hwIfMonitorCrcErrorStatistics Counter64
  hwIfMonitorCrcErrorThreshold Integer32
  hwIfMonitorCrcErrorInterval Integer32
  hwIfMonitorSdhErrorStatistics Counter64
  hwIfMonitorSdhErrorThreshold Integer32
  hwIfMonitorSdhErrorInterval Integer32
  hwIfMonitorInputRate Integer32
  hwIfMonitorInputRateThreshold Integer32
  hwIfMonitorOutputRate Integer32
  hwIfMonitorOutputRateThreshold Integer32
  hwIfMonitorPauseFrameStatistics Counter64
  hwIfMonitorPauseFrameThreshold Integer32
  hwIfMonitorPauseFrameInterval Integer32
  hwIfMonitorDelayValue Integer32
  hwIfMonitorDelayThreshold Integer32
  hwIfMonitorJitterValue Integer32
  hwIfMonitorJitterThreshold Integer32
  hwIfMonitorName DisplayString
  hwIfMonitorSdhB1ErrorStatistics Counter64
  hwIfMonitorSdhB1ErrorThreshold Integer32
  hwIfMonitorSdhB1ErrorInterval Integer32
  hwIfMonitorSdhB2ErrorStatistics Counter64
  hwIfMonitorSdhB2ErrorThreshold Integer32
  hwIfMonitorSdhB2ErrorInterval Integer32
  hwIfMonitorSymbolErrorStatistics Counter64
  hwIfMonitorSymbolErrorThreshold Integer32
  hwIfMonitorSymbolErrorInterval Integer32
  hwIfMonitorBadBytesErrorStatistics Counter64
  hwIfMonitorBadBytesErrorThreshold Integer32
  hwIfMonitorBadBytesErrorInterval Integer32

HwAdminVrrpMemberIfEntry  
SEQUENCE    
  hwAdminVrrpMemberIfIndex InterfaceIndex
  hwAdminVrrpVrid Integer32
  hwAdminVrrpIfIndex InterfaceIndex
  hwAdminVrrpMemberIfFlowStatus INTEGER
  hwAdminVrrpMemberIfRowStatus RowStatus

HwIfFluxLimitEntry  
SEQUENCE    
  hwIfFluxIfIndex InterfaceIndex
  hwIfFluxVlanId VlanIdOrNone
  hwIfFluxDirection HWDirectionType
  hwIfFluxLimitType INTEGER
  hwIfFluxCir Integer32
  hwIfFluxCbs Integer32
  hwIfFluxRowStatus RowStatus

HwIfDiffServEntry  
SEQUENCE    
  hwIfDiffServIndex InterfaceIndex
  hwIfDiffServMode INTEGER
  hwIfDiffServServiceClass INTEGER
  hwIfDiffServColor INTEGER

HwIfQueryEntry  
SEQUENCE    
  hwIfName OCTET STRING
  hwIfIndex InterfaceIndex

HwLogicIfEntry  
SEQUENCE    
  hwLogicIfIndex InterfaceIndexOrZero
  hwLogicIfMainIndex InterfaceIndexOrZero
  hwLogicIfType INTEGER
  hwLogicIfName DisplayString
  hwLogicIfParaOne INTEGER
  hwLogicIfRowStatus RowStatus

HwLogicIfHelpEntry  
SEQUENCE    
  hwLogicIfhelpType INTEGER
  hwLogicIfChassisNumber OCTET STRING
  hwLogicIfSlotNumber OCTET STRING
  hwLogicIfCardNumber OCTET STRING
  hwLogicIfMin Integer32
  hwLogicIfMax Integer32
  hwLogicIfTotal Integer32

HwLogicIfDynamicHelpEntry  
SEQUENCE    
  hwLogicDynamicIfhelpType INTEGER
  hwLogicDynamicIfChassisNumber Integer32
  hwLogicDynamicIfSlotNumber Integer32
  hwLogicDynamicIfCardNumber Integer32
  hwLogicDynamicIfMin Integer32
  hwLogicDynamicIfMax Integer32
  hwLogicDynamicIfTotal Integer32

HwCppsInterfaceEntry  
SEQUENCE    
  hwCppsInterfaceIndex InterfaceIndex
  hwCppsPortPvcEnable EnabledStatus
  hwCppsPortVlanEnable EnabledStatus

HwCppsIfStatisticsEntry  
SEQUENCE    
  hwCppsIfStatisticsIndex InterfaceIndex
  hwCppsInterfacePktStatisic Counter64
  hwCppsInterfaceByteStatisic Counter64
  hwCppsResetInterfaceStatisic INTEGER

HwCppsAtmPvcEntry  
SEQUENCE    
  hwCppsAtmIfIndex InterfaceIndex
  hwCppsAtmVpi AtmVpIdentifier
  hwCppsAtmVci AtmVcIdentifier
  hwCppsAtmPvcPktStatisic Counter64
  hwCppsAtmPvcByteStatisic Counter64
  hwCppsResetAtmPvcStatisic INTEGER

HwCppsPortVlanEntry  
SEQUENCE    
  hwCppsPortIndex InterfaceIndex
  hwCppsVlanId VlanIdOrNone
  hwCppsPortVlanPktStatisic Counter64
  hwCppsPortVlanByteStatisic Counter64
  hwCppsResetPortVlanStatisic INTEGER

HwPortIsolationGroupEntry  
SEQUENCE    
  hwPortIsolationGroupIndex Integer32 0..63
  hwPortIsolationGroupPortList PortList
  hwPortIsolationGroupRowStatus RowStatus

HwVTrunkIfEntry  
SEQUENCE    
  hwVTrunkIfIndex InterfaceIndex
  hwVTrunkIfID Integer32
  hwVTrunkIfType INTEGER
  hwVTrunkIfRowStatus RowStatus

HwVTrunkMemEntry  
SEQUENCE    
  hwVTrunkMemIfIndex Integer32
  hwVTrunkIfnetIndex Integer32
  hwVTrunkValidEntry INTEGER
  hwVTrunkOperstatus INTEGER
  hwVTrunkPortActive INTEGER
  hwVTrunkRowStatus RowStatus

HwMasterBackupTrunkSubinterfaceEntry  
SEQUENCE    
  hwBackupTrunkIfIndex InterfaceIndex
  hwBackupStatus INTEGER
  hwRevertiveMode INTEGER
  hwWtrTime Integer32
  hwFlushVlanId VlanIdOrNone

HwVaspPortPeerMacEntry  
SEQUENCE    
  hwVaspPortIfIndex InterfaceIndex
  hwVaspPortName DisplayString
  hwVaspPortPeerMac PhysAddress

HwTrunkMapEntry  
SEQUENCE    
  hwTrunkMapType INTEGER
  hwTrunkMapID Integer32
  hwTrunkMapIndex Integer32

Defined Values

hwIFExtMib 1.3.6.1.4.1.2011.5.25.41
Some attribute of interface extended content, information of interface IP, interface of trunk interface.
MODULE-IDENTITY    

hwIFExtObjects 1.3.6.1.4.1.2011.5.25.41.1
OBJECT IDENTIFIER    

hwIFExtBase 1.3.6.1.4.1.2011.5.25.41.1.1
OBJECT IDENTIFIER    

hwIFExtTable 1.3.6.1.4.1.2011.5.25.41.1.1.1
Interface extended table of private mib.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwIFExtEntry

hwIFExtEntry 1.3.6.1.4.1.2011.5.25.41.1.1.1.1
Entries of private extended interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwIFExtEntry  

hwIFExtIndex 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.1
Index of extended table of interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwIFExtLayer 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.2
Switch the port between Layer3 and Layer2. Corresponding to the port switch command.Layer2(1) is 1 when the port switch from layer3 to layer2.Layer3(1) is 1 when the port switch from lyaer2 to layer3.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER layer2(1), layer3(2)  

hwIFExtFrameType 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.3
Frame type is accepted by VLAN virtual interfaces.Frame format contains ethernetII(1),ethernetII(2),ethernet8022(3),ethernet8023. The type location setting 1 when the ethernetII(1) type is accepted.Now only surpport the first(ethernetII(1))
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ethernetII(1), ethernetSnap(2), ethernet8022(3), ethernet8023(4), other(5)  

hwIFExtFlowStatInterval 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.4
Interval of interface flow stat.The value of interval must be divided exactly by 10.The interface interval is effective,when both interface interval and global interval are config.Globle interval is only effective in interfaces,which interface interval is not configured. The real time property of interface flow stat rate will be affected by the value of interval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..600  

hwIFExtFlushReceiveEnable 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.5
Whether or not permit the port to take over FLUSHDUs. Once it is enabled, the port will take over SmartLink FlushDUs from related vlans so as to delete the MAC forwarding table in the local equipment.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwIFExtFlushVlanId 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.6
The ID of Vlan the port belongs to.When it is 0, it indicates the function of receiving FlushPDU is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIdOrNone  

hwIFExtFlushPasswd 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.7
A 16-octet read-write value used to define the password for negotiation.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpPasswdString  

hwIFExtFlowStatus 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.8
Current flow status of interface. 1:flow up 2:flow down
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER flowUp(1), flowDown(2)  

hwIFExtMtu 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.9
The Max Transmit Unit of the interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwIFExtMacAddr 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.10
The MAC address of the interface .
Status: current Access: read-write
OBJECT-TYPE    
  PhysAddress  

hwIFExtBlockPriority 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.11
The blocked priority of the interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

hwIFExtMacShift 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.12
The mac-shift state of the interface. 1:normal 2:monitor mac-shift
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), macShift(2)  

hwIFExtSuppressStatus 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.13
The suppress state of the interface. 0:unsuppress 1:suppress
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unsuppress(0), suppress(1)  

hwIFExtPoisonReverse 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.14
Whether or not enable Split-horizon forwarding
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwIFExtInputPktRate 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.15
This object indicates the rate of the incoming packets on an interface. The rate value is 64 bits. hwIFExtInputPktRate indicates the lower 32 bits, while hwIFExtInputHighPktRate indicates the higher 32 bits.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwIFExtInputHighPktRate 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.16
This object indicates the rate of the incoming packets on an interface. The rate value is 64 bits. hwIFExtInputPktRate indicates the lower 32 bits, while hwIFExtInputHighPktRate indicates the higher 32 bits.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwIFExtOutputPktRate 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.17
This object indicates the rate of the outgoing packets on an interface. The rate value is 64 bits. hwIFExtOutputPktRate indicates the lower 32 bits, while hwIFExtOutputHighPktRate indicates the higher 32 bits.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwIFExtOutputHighPktRate 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.18
This object indicates the rate of the outgoing packets on an interface. The rate value is 64 bits. hwIFExtOutputPktRate indicates the lower 32 bits, while hwIFExtOutputHighPktRate indicates the higher 32 bits.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwIFExtInputOctetRate 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.19
This object indicates the octet rate of the incoming traffic on an interface. The rate value is 64 bits. hwIFExtInputOctetRate indicates the lower 32 bits, while hwIFExtInputHighOctetRate indicates the higher 32 bits.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwIFExtInputHighOctetRate 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.20
This object indicates the octet rate of the incoming traffic on an interface. The rate value is 64 bits. hwIFExtInputOctetRate indicates the lower 32 bits, while hwIFExtInputHighOctetRate indicates the higher 32 bits.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwIFExtOutputOctetRate 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.21
This object indicates the octet rate of the outgoing traffic on an interface. The rate value is 64 bits. hwIFExtOutputOctetRate indicates the lower 32 bits, while hwIFExtOutputHighOctetRate indicates the higher 32 bits.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwIFExtOutputHighOctetRate 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.22
This object indicates the octet rate of the outgoing traffic on an interface. The rate value is 64 bits. hwIFExtOutputOctetRate indicates the lower 32 bits, while hwIFExtOutputHighOctetRate indicates the higher 32 bits.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwIFExtSwitchPortIndex 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.23
Number of layer2 interface port, a unique value, for each port.It is recommended that values are assigned contiguously starting from 1.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

hwIFExtSuppressStatusIPv6 1.3.6.1.4.1.2011.5.25.41.1.1.1.1.24
The suppress state of the interface(IPv6). 0:unsuppress 1:suppress
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unsuppress(0), suppress(1)  

hwIFExtPhyStatus 1.3.6.1.4.1.2011.5.25.41.1.1.2
The physical status of member interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER up(1), down(2)  

hwIFExtMemberOf 1.3.6.1.4.1.2011.5.25.41.1.1.3
The description of the main interface which has the membership with the member interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

hwLinkModeChangeAutoCreateIfTable 1.3.6.1.4.1.2011.5.25.41.1.1.4
Interface extended table of private mib.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwLinkModeChangeAutoCreateIfEntry

hwLinkModeChangeAutoCreateIfEntry 1.3.6.1.4.1.2011.5.25.41.1.1.4.1
Entries of private extended interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwLinkModeChangeAutoCreateIfEntry  

hwAutoIfIndex 1.3.6.1.4.1.2011.5.25.41.1.1.4.1.1
Index of extended table of interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwNewIfTimeslot 1.3.6.1.4.1.2011.5.25.41.1.1.4.1.2
The time slot of the TDM interface: timeslot0(0):The time slot 0 on the TDM interface, timeslot1(1):The time slot 1 on the TDM interface, timeslot2(2):The time slot 2 on the TDM interface, timeslot3(3):The time slot 3 on the TDM interface, timeslot4(4):The time slot 4 on the TDM interface, timeslot5(5):The time slot 5 on the TDM interface, timeslot6(6):The time slot 6 on the TDM interface, timeslot7(7):The time slot 7 on the TDM interface, timeslot8(8):The time slot 8 on the TDM interface, timeslot9(9):The time slot 9 on the TDM interface, timeslot10(10):The time slot 10 on the TDM interface, timeslot11(11):The time slot 11 on the TDM interface, timeslot12(12):The time slot 12 on the TDM interface, timeslot13(13):The time slot 13 on the TDM interface, timeslot14(14):The time slot 14 on the TDM interface, timeslot15(15):The time slot 15 on the TDM interface, timeslot16(16):The time slot 16 on the TDM interface, timeslot17(17):The time slot 17 on the TDM interface, timeslot18(18):The time slot 18 on the TDM interface, timeslot19(19):The time slot 19 on the TDM interface, timeslot20(20):The time slot 20 on the TDM interface, timeslot21(21):The time slot 21 on the TDM interface, timeslot22(22):The time slot 22 on the TDM interface, timeslot23(23):The time slot 23 on the TDM interface, timeslot24(24):The time slot 24 on the TDM interface, timeslot25(25):The time slot 25 on the TDM interface, timeslot26(26):The time slot 26 on the TDM interface, timeslot27(27):The time slot 27 on the TDM interface, timeslot28(28):The time slot 28 on the TDM interface, timeslot29(29):The time slot 29 on the TDM interface, timeslot30(30):The time slot 30 on the TDM interface, timeslot31(31):The time slot 31 on the TDM interface.
Status: current Access: read-only
OBJECT-TYPE    
  BITS timeslot0(0), timeslot1(1), timeslot2(2), timeslot3(3), timeslot4(4), timeslot5(5), timeslot6(6), timeslot7(7), timeslot8(8), timeslot9(9), timeslot10(10), timeslot11(11), timeslot12(12), timeslot13(13), timeslot14(14), timeslot15(15), timeslot16(16), timeslot17(17), timeslot18(18), timeslot19(19), timeslot20(20), timeslot21(21), timeslot22(22), timeslot23(23), timeslot24(24), timeslot25(25), timeslot26(26), timeslot27(27), timeslot28(28), timeslot29(29), timeslot30(30), timeslot31(31)  

hwIFExtPhyNumber 1.3.6.1.4.1.2011.5.25.41.1.1.5
The number of the physical interfaces.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwInterfaceIp 1.3.6.1.4.1.2011.5.25.41.1.2
OBJECT IDENTIFIER    

hwIfIpTable 1.3.6.1.4.1.2011.5.25.41.1.2.1
Interface IP address configuration table .It contains IP address, IP address mask, IP address acquiring method.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwIfIpEntry

hwIfIpEntry 1.3.6.1.4.1.2011.5.25.41.1.2.1.1
Interface IP address configuration
Status: current Access: not-accessible
OBJECT-TYPE    
  HwIfIpEntry  

hwIpAdEntAddr 1.3.6.1.4.1.2011.5.25.41.1.2.1.1.1
The IP address to which this entry's addressing information pertains.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

hwIpAdEntIfIndex 1.3.6.1.4.1.2011.5.25.41.1.2.1.1.2
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwIpAdEntNetMask 1.3.6.1.4.1.2011.5.25.41.1.2.1.1.3
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the host bits set to 0.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hwIpAdEntBcastAddr 1.3.6.1.4.1.2011.5.25.41.1.2.1.1.4
The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwIpAdEntReasmMaxSize 1.3.6.1.4.1.2011.5.25.41.1.2.1.1.5
The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagram received on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

hwIpAdEntAddressType 1.3.6.1.4.1.2011.5.25.41.1.2.1.1.6
The flag indicates whether the IP address is primary IP address. One interface has only one primary IP address, but can have many sub IP address. So when add a primary IP address to an interface that has already a primary IP address, the new primary address will replace old primary address and the old primary address will be deleted.
Status: current Access: read-create
OBJECT-TYPE    
  HwIpAddressType  

hwIfIpMethod 1.3.6.1.4.1.2011.5.25.41.1.2.1.1.7
Interface IP address acquiring method. assignedIp(1) indicates that the address was manually configured to a specified address, for example, by user configuration. dhcpIp(2) indicates an address that was assigned to this system by a DHCP server. bootpIp(3) indicates an address that was assigned to this system by the bootp protocol. other(4) indicates an address created by another method. linklayer(5) indicates an address created by IPv6 stateless auto-configuration. random(6) indicates an address chosen by the system at random, for example, an IPv4 address within 169.254/16, or an RFC 3041 privacy address.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER assignedIp(1), dhcpIp(2), bootpIp(3), other(4), linklayer(5), random(6)  

hwIpAdEntAddrStatus 1.3.6.1.4.1.2011.5.25.41.1.2.1.1.8
The row status variable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwIfIpUnnumberedTable 1.3.6.1.4.1.2011.5.25.41.1.2.2
Interface IP address unnumbered table. It contains lend IP address and lend IP address mask.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwIfIpUnnumberedEntry

hwIfIpUnnumberedEntry 1.3.6.1.4.1.2011.5.25.41.1.2.2.1
Interface IP address unnumbered configuration
Status: current Access: not-accessible
OBJECT-TYPE    
  HwIfIpUnnumberedEntry  

hwUnnumberedIfIndex 1.3.6.1.4.1.2011.5.25.41.1.2.2.1.1
The index value of the unnumbered interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwLendIfIndex 1.3.6.1.4.1.2011.5.25.41.1.2.2.1.11
The index value of the lend interface.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

hwLendIpAddr 1.3.6.1.4.1.2011.5.25.41.1.2.2.1.12
The IP address of the lend interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

hwLendIpAddrNetMask 1.3.6.1.4.1.2011.5.25.41.1.2.2.1.13
The IP address mask of the lend interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

hwUnnumberedRowStatus 1.3.6.1.4.1.2011.5.25.41.1.2.2.1.51
The row status variable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwIfIpAddrTable 1.3.6.1.4.1.2011.5.25.41.1.2.3
This table contains addressing information relevant to the entity's interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwIfIpAddrEntry

hwIfIpAddrEntry 1.3.6.1.4.1.2011.5.25.41.1.2.3.1
Interface IP address configuration
Status: current Access: not-accessible
OBJECT-TYPE    
  HwIfIpAddrEntry  

hwIfIpAddrEntIfIndex 1.3.6.1.4.1.2011.5.25.41.1.2.3.1.1
The index value that uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of the IF-MIB's ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwIfIpAddrEntAddr 1.3.6.1.4.1.2011.5.25.41.1.2.3.1.2
The IP address to which this entry's addressing information pertains.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

hwIfIpAddrEntType 1.3.6.1.4.1.2011.5.25.41.1.2.3.1.3
The type of address.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unicast(1), anycast(2), broadcast(3)  

hwIfIpAddrEntPrefix 1.3.6.1.4.1.2011.5.25.41.1.2.3.1.4
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the host bits set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

hwIfIpAddrEntOrigin 1.3.6.1.4.1.2011.5.25.41.1.2.3.1.5
Interface IP address acquiring method. assignedIp(1) indicates that the address was manually configured to a specified address, for example, by user configuration. dhcpIp(2) indicates an address that was assigned to this system by a DHCP server. bootpIp(3) indicates an address that was assigned to this system by the bootp protocol. other(4) indicates an address created by another method. linklayer(5) indicates an address created by IPv6 stateless auto-configuration. random(6) indicates an address chosen by the system at random, for example, an IPv4 address within 169.254/16, or an RFC 3041 privacy address.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER assignedIp(1), dhcpIp(2), bootpIp(3), other(4), linklayer(5), random(6)  

hwIfIpAddrEntStatus 1.3.6.1.4.1.2011.5.25.41.1.2.3.1.6
The status of the address, describing if the address can be used for communication. In the absence of other information, an IPv4 address is always preferred(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER preferred(1), deprecated(2), invalid(3), inaccessible(4), unknown(5), tentative(6), duplicate(7), optimistic(8)  

hwIfIpAddrEntCreated 1.3.6.1.4.1.2011.5.25.41.1.2.3.1.7
The value of sysUpTime at the time this entry was created. If this entry was created prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

hwIfIpAddrEntLastChanged 1.3.6.1.4.1.2011.5.25.41.1.2.3.1.8
The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

hwIfIpAddrEntBcastAddr 1.3.6.1.4.1.2011.5.25.41.1.2.3.1.9
The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwIfIpAddrEntReasmMaxSize 1.3.6.1.4.1.2011.5.25.41.1.2.3.1.10
The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagram received on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

hwIfIpAddrEntAddrType 1.3.6.1.4.1.2011.5.25.41.1.2.3.1.11
The flag indicates whether the IP address is primary IP address.
Status: current Access: read-only
OBJECT-TYPE    
  HwIpAddressType  

hwIfIpAddrEntVpn 1.3.6.1.4.1.2011.5.25.41.1.2.3.1.12
The vpn name of ip address.The public address does not have any value.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

hwTrunkAttr 1.3.6.1.4.1.2011.5.25.41.1.3
OBJECT IDENTIFIER    

hwTrunkIfMax 1.3.6.1.4.1.2011.5.25.41.1.3.1
The maximum of Trunk interface
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwTrunkNextIndex 1.3.6.1.4.1.2011.5.25.41.1.3.2
The nextindex of Trunk interface,that means its position
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwTrunkIfTable 1.3.6.1.4.1.2011.5.25.41.1.3.3
The trunk table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwTrunkIfEntry

hwTrunkIfEntry 1.3.6.1.4.1.2011.5.25.41.1.3.3.1
Entries of the trunk table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwTrunkIfEntry  

hwTrunkIndex 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.1
The number of the Trunk interface
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hwTrunkIfID 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.2
The identification of the Trunk interface.It may identify Trunk and is an index of the interface.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwTrunkIfType 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.3
The type of the Trunk interface includes eth-trunk and ip-trunk. The ip-trunk is only comprised by pos link, otherwise the eth-trunk is only comprised by ethernet link.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ethTrunk(1), ipTrunk(2)  

hwTrunkIfIndex 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.4
Index number of the Trunk interface,it is consistent with ifIndex of ifTable in IF-MIB.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

hwTrunkIfModel 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.5
Participated model of interface load. sourceDesMac(2) and sourceMac(10) and desMac(11) are Layer2 hash arithmetic.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER packetAll(1), sourceDesMac(2), packetUdp(3), packetTcp(4), sourceDesIp(5), sourceMacIpv6(6), sourceIpIpv6(7), sourceIp(8), desIp(9), sourceMac(10), desMac(11), sourcePort(12), desPort(13), sourceDesPort(14), fwdType(15), qos(16), labelNum(17), label(18), enhanced(19), l4(20), invalid(-1)  

hwTrunkIfBandWidthAffectLinkNum 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.6
The max bandwidth-affected-linknumber, by default, an Eth-Trunk interface has a maximum of 16 physical interfaces. The number of physical interfaces in an Eth-Trunk interface varies according to the product type.Only in layer 2,can set this value.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwTrunkIfMinLinkNum 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.7
The Trunk port changes to up when the number of the up port reach hwTrunkIfMinLinkNum.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwTrunkIfRowStatus 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.8
Current operation status of the row
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwTrunkIfWorkingMode 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.9
Current working mode of trunk. 1:master/backup access mode 2:normal mode 3:lacp static mode 4:lacp compatible mode 5:port standby mode
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER masterBackup(1), normalMode(2), lacpMode(3), lacpCompatibleMode(4), portStandbyMode(5), invalid(-1)  

hwTrunkIfWorkingState 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.10
Current working state of backup-access trunk. 1:general mode working state 2:initialization 3:master working 4:backup working
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER generalMode(1), initialization(2), masterWorking(3), backupWorking(4), invalid(-1)  

hwTrunkIfAutoRecover 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.11
If auto-recover has been set, the master port will be working instead of the other port when it changes from down state to up state. 1: don't support auto-recover 2: support auto-recover
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER generalMode(1), autoRecover(2), invalid(-1)  

hwTrunkIfPreemptEnable 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.12
The preemption according to the priority will be and only be enabled when the lag port is working in static mode(M:N backup mode) In default condition, the preemption is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), invalid(-1)  

hwTrunkIfPreemptDelay 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.13
The waiting time for priority preemption; Unit: second. It is enabled only when the priority preemption is enabled. It indicates, When it comes to priority preemption, the operation of preemption will be delayed for hwTrunkIfPreemptDelay time. The specific minimum specification depends on products.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..180 | -1  

hwTrunkIfTimeoutReceive 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.14
The expired time for the port to receive LACPDUS. There are two types: 1.fast: The default value is customized with products. 2.slow: 90 seconds
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER fast(1), slow(2), invalid(-1)  

hwTrunkIfFlushSendEnable 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.15
Whether or not permit the trunk to transmit FlushDUs.It is only used when it is in the handwork 1:1 mode.Once it is enabled, the newly active interface in the trunk will send SmartLink FlushDUs so as to delete the related MAC forwarding table of the layer2 equipment in network.Otherwise, SmartLink FlushDUs will not be sent.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), invalid(-1)  

hwTrunkIfFlushVlanId 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.16
The ID of Vlan the partner port belongs to.When it is 0, it indicates the function of sending FlushPDU is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4094 | -1  

hwTrunkIfFlushPasswd 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.17
A 16-octet read-create value used to define the password for negotiation.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpPasswdString  

hwTrunkIfForceSwitchEnable 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.18
It is only used when it is in the handwork 1:1 mode and the current working link is the backup link. At that time, working link will move from backup link to master link. However, if the master link is down, the operation will be forbidden.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), invalid(-1)  

hwTrunkIfStatReset 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.19
Reset the statistic information of LACPDUsRx,MarkerPDUsRx,LACPDUsTx, MarkerResponsePDUsTx for all the ports in the current trunk.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER reset(1), ready(2), invalid(-1)  

hwTrunkBandwidth 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.20
Current bandwidth of trunk in units of 1,000,000 bits per second. This bandwidth is the peculiar property of Eth-Trunk. And to the other kinds of trunk, this bandwidth is -1.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwTrunkIfArpSendSpeed 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.21
Indicates the rate of sending gratuitous ARP packets (in pkts/sec) on the trunk member interface.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 800..3000 | -1  

hwTrunkIfLagSelectedPortStd 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.22
The static mode Eth-trunk selected port standard. There are two types: 1.speed : selected by port's speed 2.priority: selected by port's priority The default type is priority.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER speed(1), priority(2), invalid(-1)  

hwTrunkIfLagMaxActiveLinkNum 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.23
The static mode Eth-trunk selected ports can not more than the value.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwTrunkETrunkPriority 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.24
The priority of the E-Trunk.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535 | -1  

hwTrunkETrunkSysID 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.25
The system ID of the E-Trunk. If set ffff-ffff-ffff the system ID will be to default.
Status: current Access: read-write
OBJECT-TYPE    
  PhysAddress  

hwTrunkETrunkPriorityReset 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.26
Status of operation, there are yes(1) and no(2). It expresses whether the configure of E-Trunk priority is resetted.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2), invalid(-1)  

hwTrunkETrunkSysIDReset 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.27
Status of operation, there are yes(1) and no(2). It expresses whether the configure of E-Trunk system ID is resetted.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2), invalid(-1)  

hwTrunkLocalPrefMode 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.28
Local-preference transmit mode of eth-trunk, there are enable(1) and disable(2).The default value is enable(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwTrunkIfTrackVrrpVrid 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.29
The VRID which the static mode Eth-trunk tracked to.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwTrunkIfTrackVrrpIfIndex 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.30
The VRRP interface which the static mode Eth-trunk tracked to.
Status: current Access: read-write
OBJECT-TYPE    
  InterfaceIndex  

hwTrunkIfTrackVrrpReset 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.31
Status of operation, there are yes(1) and no(2). The value of this object identifies whether the operation of clearing the configuration is performed. And the configuration is that the Eth-Trunk interface in static LACP mode is associated with an mVRRP backup group. The value yes(1) indicates performing the operation. This object indicates one operation but not one status, so when the operation is performed, the value is no(2). By default, the value is no(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2), invalid(-1)  

hwTrunkIfBackupPreemptEnable 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.32
The preemption according to the master and slave port will be and only be enabled when eth-trunk is working in backup mode. In default condition, the preemption is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwTrunkIfBackupPreemptDelay 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.33
The waiting time for priority preemption; Unit: minute. It is enabled only when the priority preemption is enabled. It indicates, When it comes to priority preemption, the operation of preemption will be delayed for hwTrunkIfBackupPreemptDelay time.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..30 | -1  

hwTrunkIfCrcErrorSwitchEnable 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.34
make trunk member port stop in use if the port have crc error exceed the config threshold, the trunk would be down if member port in use is low
Status: current Access: read-create
OBJECT-TYPE    
  EnabledStatus  

hwTrunkIfLagTimeOut 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.35
The expired time(Unit is second) of the port to receive LACPDUS in the fast mode. The hwTrunkIfTimeoutReceive is the type of timeout and use hwTrunkIfLagTimeOut to change time in the fast mode. The default value is customized with products. If the mode is not fast, the value is always 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..90 | 0  

hwTrunkMemCount 1.3.6.1.4.1.2011.5.25.41.1.3.3.1.36
The count of Trunk member interfaces per Trunk.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwTrunkSystemPriority 1.3.6.1.4.1.2011.5.25.41.1.3.4
The priority of the system.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hwTrunkUnknownUnicastIfModel 1.3.6.1.4.1.2011.5.25.41.1.3.5
Participated model of load for unknown unicast. sourceDesMac(2) and sourceMac(10) and desMac(11) are Layer2 hash arithmetic.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER packetAll(1), sourceDesMac(2), packetUdp(3), packetTcp(4), sourceDesIp(5), sourceMacIpv6(6), sourceIpIpv6(7), sourceIp(8), desIp(9), sourceMac(10), desMac(11), sourcePort(12), desPort(13), sourceDesPort(14), label(15), ipOrLabel(16)  

hwTrunkETrunkSystemPriority 1.3.6.1.4.1.2011.5.25.41.1.3.6
The system priority of the E-Trunk.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hwTrunkETrunkSystemID 1.3.6.1.4.1.2011.5.25.41.1.3.7
The system ID of the E-Trunk. If set ffff-ffff-ffff the system ID will be to default.
Status: current Access: read-write
OBJECT-TYPE    
  PhysAddress  

hwTrunkCount 1.3.6.1.4.1.2011.5.25.41.1.3.8
Number of configured trunk interfaces on the device.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

hwTrunkMemberCountUpperThreshold 1.3.6.1.4.1.2011.5.25.41.1.3.9
Upper threshold for the number of members of the Eth-Trunk in LACP mode.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 0..65535  

hwTrunkMemberCountLowerThreshold 1.3.6.1.4.1.2011.5.25.41.1.3.10
Lower threshold for the number of members of the Eth-Trunk in LACP mode.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 0..65535  

hwTrunkMemAttr 1.3.6.1.4.1.2011.5.25.41.1.4
OBJECT IDENTIFIER    

hwTrunkMemTable 1.3.6.1.4.1.2011.5.25.41.1.4.1
Trunk member attribute information table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwTrunkMemEntry

hwTrunkMemEntry 1.3.6.1.4.1.2011.5.25.41.1.4.1.1
Trunk member attribute information
Status: current Access: not-accessible
OBJECT-TYPE    
  HwTrunkMemEntry  

hwTrunkMemifIndex 1.3.6.1.4.1.2011.5.25.41.1.4.1.1.1
Trunk port index
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hwTrunkValidEntry 1.3.6.1.4.1.2011.5.25.41.1.4.1.1.2
Valid Entries of Trunk interface
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

hwTrunkSelectStatus 1.3.6.1.4.1.2011.5.25.41.1.4.1.1.3
Selected Status of Trunk Port.It is used LACP.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER trunkSelected(1), trunkDeselected(2), trunkIndep(3), invalid(-1)  

hwTrunkLacpStatus 1.3.6.1.4.1.2011.5.25.41.1.4.1.1.4
It is status of the LACP.
Status: current Access: read-only
OBJECT-TYPE    
  EnabledStatus  

hwTrunkDeleteFlag 1.3.6.1.4.1.2011.5.25.41.1.4.1.1.5
Flag is set trunk_del_enable(1) or trunk_del_disable(2), according to operation.
Status: current Access: read-create
OBJECT-TYPE    
  EnabledStatus  

hwTrunkOperstatus 1.3.6.1.4.1.2011.5.25.41.1.4.1.1.6
Status of operation, indicates port status. There are trunk_up(1) and trunk_down(2).It expresses whether port is shutdown.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

hwTrunkIsDefaultLagRecv 1.3.6.1.4.1.2011.5.25.41.1.4.1.1.7
We don't sustain now, default value is false.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hwTrunkPortWeight 1.3.6.1.4.1.2011.5.25.41.1.4.1.1.8
Port weight, it expresses proportion of port in Trunk interface table
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwTrunkPortStandby 1.3.6.1.4.1.2011.5.25.41.1.4.1.1.9
The value is backup of Trunk Port.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwTrunkRowStatus 1.3.6.1.4.1.2011.5.25.41.1.4.1.1.10
Current operation status of the row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwTrunkPortMaster 1.3.6.1.4.1.2011.5.25.41.1.4.1.1.11
Master port of backup-access eth-trunk or not 1: port-slave 2: port-master
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER portSlave(1), portMaster(2), invalid(-1)  

hwTrunkPortPriority 1.3.6.1.4.1.2011.5.25.41.1.4.1.1.12
The priority value assigned to this Trunk Port. This 16-bit value is read-write.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535 | -1  

hwTrunkPortStatReset 1.3.6.1.4.1.2011.5.25.41.1.4.1.1.13
Reset the statistic information of LACPDUsRx,MarkerPDUsRx,LACPDUsTx, MarkerResponsePDUsTx for the current port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER reset(1), ready(2), invalid(-1)  

hwTrunkPortLacpMode 1.3.6.1.4.1.2011.5.25.41.1.4.1.1.14
The mode of port joining Lacp.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER invalid(1), active(2), passive(3)  

hwIFFlowStat 1.3.6.1.4.1.2011.5.25.41.1.5
OBJECT IDENTIFIER    

hwIFFlowStatGlobalInterval 1.3.6.1.4.1.2011.5.25.41.1.5.1
Global interval of interface flow stat.The interface interval is effective, when both interface interval and global interval are config.Globle interval is only effective in interfaces,which interface interval is not configged. Flow stat rate of interface will be affected by the value of interval. The default value is 300s.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..600  

hwIfStatistics 1.3.6.1.4.1.2011.5.25.41.1.6
OBJECT IDENTIFIER    

hwIfEtherStatTable 1.3.6.1.4.1.2011.5.25.41.1.6.1
Ethernet Interface Statistic Table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwIfEtherStatEntry

hwIfEtherStatEntry 1.3.6.1.4.1.2011.5.25.41.1.6.1.1
Entry of Ethernet Interface Statistic Table
Status: current Access: not-accessible
OBJECT-TYPE    
  HwIfEtherStatEntry  

hwIfEtherStatIfIndex 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.1
The index of L2 interface
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwIfEtherStatInPkts64Octets 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.5
The number of recieved Packets whose size over 1518 bytes
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInPkts65to127Octets 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.6
The number of recieved Packets whose size over 1518 bytes
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInPkts128to255Octets 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.7
The number of recieved Packets whose size over 1518 bytes
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInPkts256to511Octets 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.8
The number of recieved Packets whose size over 1518 bytes
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInPkts512to1023Octets 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.9
The number of recieved Packets whose size over 1518 bytes
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInPkts1024to1518Octets 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.10
The number of recieved Packets whose size over 1518 bytes
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInJumboPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.11
The number of recieved Packets whose size over 1518 bytes
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInCRCPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.12
The number of recieved Packets which have CRC checking errors
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInLongPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.13
The number of recieved Packets whose length is over maximum length
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInJabberPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.14
The number of recieved Packets whose length is over maximum length and wrong CRC checking
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInFragmentPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.15
The number of recieved Packets which have short size and wrong CRC checking
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInUnderSizePkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.16
The number of recieved Packets which have short size but right CRC checking
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInOverRunPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.17
The number of recieved Packets whose queue overflow
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInPausePkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.18
The number of recieved control Frames
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatOutJumboPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.19
The number of sended Packets whose size over 1518 bytes
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatOutOverflowPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.20
The number of Packets whitch happen FIFO overflow error
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatOutUnderRunPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.21
The number of Packets whitch happen FIFO empty
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatOutPausePkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.22
The number of sended control Frames
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEthIfStatReset 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.23
Reset the Statistic information Counter
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), ready(2)  

hwIfEtherStatInDropEventPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.24
The number of recieved Packets discarded for GBP full or back pressure discard
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInAlignmentPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.25
The number of recieved Packets which have frame alignment error
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInSymbolPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.26
The number of recieved Packets which have unknown symbols
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInIgnoredPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.27
The number of recieved MAC control frames which have unknown opecode
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatInFramePkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.28
The number of recieved frames whose actual length differs with 802.3
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatOutCollisionPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.29
The number of sended collision Frames(only happen in the 10/100M port with half duplex mode)
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatOutDeferredPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.30
The number of sended deferred but not collision Frames(only happen in the 10/100M port)
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatOutLateCollisionPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.31
The number of sended deferred and collision Frames(only happen in the 10/100M port)
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatOutExcessiveCollisionPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.32
The number of sended failure Frames whose collision more than 16(only happen in the 10/100M port)
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfEtherStatOutBufferPurgationPkts 1.3.6.1.4.1.2011.5.25.41.1.6.1.1.33
The number of sended Frames which is purged from the buffer because of long time
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfSdhStatTable 1.3.6.1.4.1.2011.5.25.41.1.6.2
Sdh/sonet Interface Statistic Table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwIfSdhStatEntry

hwIfSdhStatEntry 1.3.6.1.4.1.2011.5.25.41.1.6.2.1
Entry of Sdh/Sonet Interface Statistic Table
Status: current Access: not-accessible
OBJECT-TYPE    
  HwIfSdhStatEntry  

hwIfSdhStatIfIndex 1.3.6.1.4.1.2011.5.25.41.1.6.2.1.1
The index of sdh/sonet interface
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwIfSdhStatInCRCPkts 1.3.6.1.4.1.2011.5.25.41.1.6.2.1.2
The number of recieved Packets which have CRC checking errors
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfSdhStatInShortPkts 1.3.6.1.4.1.2011.5.25.41.1.6.2.1.3
The number of recieved Packets whose length is under minimal length
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfSdhStatInLongPkts 1.3.6.1.4.1.2011.5.25.41.1.6.2.1.4
The number of recieved Packets whose length is over maximum length
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfSdhStatOutOverRunPkts 1.3.6.1.4.1.2011.5.25.41.1.6.2.1.5
The number of sent Packets whose queue overflow
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfSdhStatOutUnderRunPkts 1.3.6.1.4.1.2011.5.25.41.1.6.2.1.6
The number of sent Packets whose queue underflow
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfSdhIfStatReset 1.3.6.1.4.1.2011.5.25.41.1.6.2.1.7
Reset the Statistic information Counter
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), ready(2)  

hwIfAtmStatTable 1.3.6.1.4.1.2011.5.25.41.1.6.3
Atm Interface Statistic Table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwIfAtmStatEntry

hwIfAtmStatEntry 1.3.6.1.4.1.2011.5.25.41.1.6.3.1
Entry of Atm Interface Statistic Table
Status: current Access: not-accessible
OBJECT-TYPE    
  HwIfAtmStatEntry  

hwIfAtmStatIfIndex 1.3.6.1.4.1.2011.5.25.41.1.6.3.1.1
The index of atm interface
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwIfAtmStatInGoodCells 1.3.6.1.4.1.2011.5.25.41.1.6.3.1.2
The number of good cells recieved
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfAtmStatInIdleCells 1.3.6.1.4.1.2011.5.25.41.1.6.3.1.3
The number of idle cells recieved
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfAtmStatInCorrectedCells 1.3.6.1.4.1.2011.5.25.41.1.6.3.1.4
The number of recieved cells whitch have been corrected.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfAtmStatInUncorrectedCells 1.3.6.1.4.1.2011.5.25.41.1.6.3.1.5
The number of recieved cells whitch can not be corrected.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfAtmStatOutGoodCells 1.3.6.1.4.1.2011.5.25.41.1.6.3.1.6
The number of good cells sent
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfAtmStatOutIdleCells 1.3.6.1.4.1.2011.5.25.41.1.6.3.1.7
The number of idle cells sent
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfAtmIfStatReset 1.3.6.1.4.1.2011.5.25.41.1.6.3.1.8
Reset the Statistic information Counter
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), ready(2)  

hwIfMonitorObject 1.3.6.1.4.1.2011.5.25.41.1.7
OBJECT IDENTIFIER    

hwIfMonitorThresholdTable 1.3.6.1.4.1.2011.5.25.41.1.7.1
Alarm monitor table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwIfMonitorThresholdEntry

hwIfMonitorThresholdEntry 1.3.6.1.4.1.2011.5.25.41.1.7.1.1
Entry of alarm monitor table
Status: current Access: not-accessible
OBJECT-TYPE    
  HwIfMonitorThresholdEntry  

hwIfMonitorIndex 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.1
Index of alarm monitor table
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwIfMonitorCrcErrorStatistics 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.2
Crc error statistics value
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfMonitorCrcErrorThreshold 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.3
Crc error alarm threshold,default value is 3 and 0 is an invalid value
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hwIfMonitorCrcErrorInterval 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.4
Crc error alarm interval time(unit is second),default value is 10s and 0 is an invalid value
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hwIfMonitorSdhErrorStatistics 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.5
Sdh error statistics value only for B3
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfMonitorSdhErrorThreshold 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.6
Sdh error alarm threshold,only for B3,default value is 3 and 0 is an invalid value
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hwIfMonitorSdhErrorInterval 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.7
Sdh error alarm interval time(unit is second),only for B3,default value is 10s and 0 is an invalid value
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hwIfMonitorInputRate 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.8
Input rate percentage value
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hwIfMonitorInputRateThreshold 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.9
Input rate alarm threshold,default value is 100
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..100  

hwIfMonitorOutputRate 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.10
Output rate percentage value
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hwIfMonitorOutputRateThreshold 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.11
Output rate alarm threshold,default value is 100
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..100  

hwIfMonitorPauseFrameStatistics 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.12
Pause frame statistics value
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfMonitorPauseFrameThreshold 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.13
Pause frame alarm threshold,and 0 is an invalid value
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hwIfMonitorPauseFrameInterval 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.14
Pause frame alarm interval time(unit is second),and 0 is an invalid value
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hwIfMonitorDelayValue 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.15
Delay value
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

hwIfMonitorDelayThreshold 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.16
Delay alarm threshold
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

hwIfMonitorJitterValue 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.17
Jitter value
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

hwIfMonitorJitterThreshold 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.18
Jitter alarm threshold
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

hwIfMonitorName 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.19
Interface's name of alarm monitor table
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

hwIfMonitorSdhB1ErrorStatistics 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.20
Sdh B1 error statistics value
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfMonitorSdhB1ErrorThreshold 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.21
Sdh B1 error alarm threshold,default value is 3
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

hwIfMonitorSdhB1ErrorInterval 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.22
Sdh B1 error alarm interval time(unit is second),default value is 10s
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

hwIfMonitorSdhB2ErrorStatistics 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.23
Sdh B2 error statistics value
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfMonitorSdhB2ErrorThreshold 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.24
Sdh error B2 alarm threshold,default value is 3
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

hwIfMonitorSdhB2ErrorInterval 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.25
Sdh B2 error alarm interval time(unit is second),default value is 10s
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

hwIfMonitorSymbolErrorStatistics 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.26
Symbol error statistics value
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfMonitorSymbolErrorThreshold 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.27
Symbol error alarm threshold,default value is 3
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

hwIfMonitorSymbolErrorInterval 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.28
Symbol error alarm interval time(unit is second),default value is 10s
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

hwIfMonitorBadBytesErrorStatistics 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.40
Description.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwIfMonitorBadBytesErrorThreshold 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.41
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwIfMonitorBadBytesErrorInterval 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.42
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwIfMonitorGeneral 1.3.6.1.4.1.2011.5.25.41.1.8
OBJECT IDENTIFIER    

hwIfMonitorCrcEnabledStatus 1.3.6.1.4.1.2011.5.25.41.1.8.1
Enalbe or disable the crc error monitor, and the default value is disable.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwIfMonitorSdhEnabledStatus 1.3.6.1.4.1.2011.5.25.41.1.8.2
Enalbe or disable the sdh error monitor, and the default value is disable.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwIfMonitorInputRateEnabledStatus 1.3.6.1.4.1.2011.5.25.41.1.8.3
Enalbe or disable the input rate monitor, and the default value is disable.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwIfMonitorOutputRateEnabledStatus 1.3.6.1.4.1.2011.5.25.41.1.8.4
Enalbe or disable the output rate monitor, and the default value is disable.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwIfMonitorHalfDuplexEnabledStatus 1.3.6.1.4.1.2011.5.25.41.1.8.5
Enalbe or disable the half duplex monitor, and the default value is disable.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwIfMonitorPauseRisingEnabledStatus 1.3.6.1.4.1.2011.5.25.41.1.8.6
Enalbe or disable the pause frame rising monitor, and the default value is disable.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwIfMonitorPauseContinuingEnabledStatus 1.3.6.1.4.1.2011.5.25.41.1.8.7
Enalbe or disable the pause frame continuing monitor, and the default value is disable.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwifMonitorBadBytesEnabledStatus 1.3.6.1.4.1.2011.5.25.41.1.8.8
Description.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwAdminVrrpMemberIf 1.3.6.1.4.1.2011.5.25.41.1.9
OBJECT IDENTIFIER    

hwIfFlowChangeTime 1.3.6.1.4.1.2011.5.25.41.1.9.1
The time indicates when the interface's flow status changes.
Status: obsolete Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

hwAdminVrrpMemberIfTable 1.3.6.1.4.1.2011.5.25.41.1.9.2
The interface bound to VRRP table.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwAdminVrrpMemberIfEntry

hwAdminVrrpMemberIfEntry 1.3.6.1.4.1.2011.5.25.41.1.9.2.1
Entries of the interface bound to VRRP table.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  HwAdminVrrpMemberIfEntry  

hwAdminVrrpMemberIfIndex 1.3.6.1.4.1.2011.5.25.41.1.9.2.1.1
The number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwAdminVrrpVrid 1.3.6.1.4.1.2011.5.25.41.1.9.2.1.2
The administrator VRRP vrid.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32  

hwAdminVrrpIfIndex 1.3.6.1.4.1.2011.5.25.41.1.9.2.1.3
The administrator VRRP's configure interface index.
Status: obsolete Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

hwAdminVrrpMemberIfFlowStatus 1.3.6.1.4.1.2011.5.25.41.1.9.2.1.4
Current flow status of interface. 1:up 2:down
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

hwAdminVrrpMemberIfRowStatus 1.3.6.1.4.1.2011.5.25.41.1.9.2.1.5
Current operation status of the row.
Status: obsolete Access: read-create
OBJECT-TYPE    
  RowStatus  

hwIfFluxLimit 1.3.6.1.4.1.2011.5.25.41.1.10
OBJECT IDENTIFIER    

hwIfFluxLimitTable 1.3.6.1.4.1.2011.5.25.41.1.10.1
Flux limit table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwIfFluxLimitEntry

hwIfFluxLimitEntry 1.3.6.1.4.1.2011.5.25.41.1.10.1.1
Entry of flux limit table
Status: current Access: not-accessible
OBJECT-TYPE    
  HwIfFluxLimitEntry  

hwIfFluxIfIndex 1.3.6.1.4.1.2011.5.25.41.1.10.1.1.1
Interface Index, same as ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwIfFluxVlanId 1.3.6.1.4.1.2011.5.25.41.1.10.1.1.2
Vlan ID. 0 is the default value
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanIdOrNone  

hwIfFluxDirection 1.3.6.1.4.1.2011.5.25.41.1.10.1.1.3
Limit direction: inbound (1) outbound (2)
Status: current Access: read-create
OBJECT-TYPE    
  HWDirectionType  

hwIfFluxLimitType 1.3.6.1.4.1.2011.5.25.41.1.10.1.1.4
Flux limit type: broadcastSuppression(1),multicastSuppression(2),unknownUnicastSuppression(3).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER broadcastSuppression(1), multicastSuppression(2), unknownUnicastSuppression(3)  

hwIfFluxCir 1.3.6.1.4.1.2011.5.25.41.1.10.1.1.5
Committed Information Rate. Unit: kbps. software QoS: 8..155000 hardware QoS: 100..10000000
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwIfFluxCbs 1.3.6.1.4.1.2011.5.25.41.1.10.1.1.6
Committed Burst Size. Unit: byte software QoS: 1875..19375000 hardware QoS: 64..33554432
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwIfFluxRowStatus 1.3.6.1.4.1.2011.5.25.41.1.10.1.1.7
RowStatus. Three actions are used: active, createAndGo, destroy
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwIfDiffServ 1.3.6.1.4.1.2011.5.25.41.1.11
OBJECT IDENTIFIER    

hwIfDiffServTable 1.3.6.1.4.1.2011.5.25.41.1.11.1
The table describes the different service mode of interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwIfDiffServEntry

hwIfDiffServEntry 1.3.6.1.4.1.2011.5.25.41.1.11.1.1
Interface different service mode attribute configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwIfDiffServEntry  

hwIfDiffServIndex 1.3.6.1.4.1.2011.5.25.41.1.11.1.1.1
The index of L2 interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwIfDiffServMode 1.3.6.1.4.1.2011.5.25.41.1.11.1.1.2
Different service mode of the interface binding to a VLL, default is uniform.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER pipe(1), uniform(2), shortpipe(3), egresspipe(4), egressshortpipe(5)  

hwIfDiffServServiceClass 1.3.6.1.4.1.2011.5.25.41.1.11.1.1.3
PHB in the ingress PE, the value must be be,af1,af2,af3,af4,ef,cs6,cs7.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER default(0), be(1), af1(2), af2(3), af3(4), af4(5), ef(6), cs6(7), cs7(8)  

hwIfDiffServColor 1.3.6.1.4.1.2011.5.25.41.1.11.1.1.4
Remarked color of packet in the ingress PE, the value must be green,yellow,red.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER default(0), green(1), yellow(2), red(3)  

hwIfQuery 1.3.6.1.4.1.2011.5.25.41.1.12
OBJECT IDENTIFIER    

hwIfQueryTable 1.3.6.1.4.1.2011.5.25.41.1.12.1
Interface name table of private MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwIfQueryEntry

hwIfQueryEntry 1.3.6.1.4.1.2011.5.25.41.1.12.1.1
Entries of private interface name table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwIfQueryEntry  

hwIfName 1.3.6.1.4.1.2011.5.25.41.1.12.1.1.1
The name of the interface.The value of this object must be the interface name assigned by the local device.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING Size(1..47)  

hwIfIndex 1.3.6.1.4.1.2011.5.25.41.1.12.1.1.2
The index of the interface. An index uniquely identifies an interface.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

hwLogicIfAttrib 1.3.6.1.4.1.2011.5.25.41.1.13
OBJECT IDENTIFIER    

hwLogicIfTable 1.3.6.1.4.1.2011.5.25.41.1.13.1
Logic interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwLogicIfEntry

hwLogicIfEntry 1.3.6.1.4.1.2011.5.25.41.1.13.1.1
Logic interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwLogicIfEntry  

hwLogicIfIndex 1.3.6.1.4.1.2011.5.25.41.1.13.1.1.1
Indicates the interface index. The interface index to be created must be 0. Then the system automatically allocates an interface index.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndexOrZero  

hwLogicIfMainIndex 1.3.6.1.4.1.2011.5.25.41.1.13.1.1.11
Indicates the interface index of the main interface to which the sub-interface belongs. For other interfaces, the interface index is 0.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

hwLogicIfType 1.3.6.1.4.1.2011.5.25.41.1.13.1.1.12
Indicates the interface type.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ve(1), loopback(2), vlanif(3), subVe(4), subEthTrunk(5), subEthernet(6), subAtm(7), imaGroup(8), subImaGroup(9), subSerial(10), tunnel(11), mpGroup(13), bridgeIf(14), subAtmTrunk(15), dslGroup(16), wlanEss(17), stackPort(18), globalImaGroup(19), subGlobalImaGroup(20), remoteAp(21), vBridge(22), atmBundle(23), mtunnel(24), subPosFr(25), globalVe(26), subGlobalVe(27)  

hwLogicIfName 1.3.6.1.4.1.2011.5.25.41.1.13.1.1.13
Indicates the interface name. The interface name must be a name without blank spaces and Tab characters.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..64)  

hwLogicIfParaOne 1.3.6.1.4.1.2011.5.25.41.1.13.1.1.14
Indicates the extended attribute of the logical interface. The extended attribute takes effect only on the ATM sub-interface. The default extended attribute is P2MP. For sub-interfaces of other types, none is returned after the Get operation.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER p2p(1), p2mp(2), none(255)  

hwLogicIfRowStatus 1.3.6.1.4.1.2011.5.25.41.1.13.1.1.51
Indicates the status of the row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwLogicIfHelpTable 1.3.6.1.4.1.2011.5.25.41.1.13.2
Logic interface help table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwLogicIfHelpEntry

hwLogicIfHelpEntry 1.3.6.1.4.1.2011.5.25.41.1.13.2.1
Logic interface help table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwLogicIfHelpEntry  

hwLogicIfhelpType 1.3.6.1.4.1.2011.5.25.41.1.13.2.1.1
Indicates the types of logical interfaces that can be queried.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ve(1), imaGroup(8), tunnel(11), mpGroup(13), dslGroup(16)  

hwLogicIfChassisNumber 1.3.6.1.4.1.2011.5.25.41.1.13.2.1.2
Indicates the ID of the chassis that supports the creation of the specified logical interface.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..2)  

hwLogicIfSlotNumber 1.3.6.1.4.1.2011.5.25.41.1.13.2.1.3
Indicates the ID of the slot that supports the creation of the specified logical interface.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

hwLogicIfCardNumber 1.3.6.1.4.1.2011.5.25.41.1.13.2.1.4
Indicates the number of the card that supports the creation of the specified logical interface.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..512)  

hwLogicIfMin 1.3.6.1.4.1.2011.5.25.41.1.13.2.1.5
Indicates the minimum port number of the specified logical interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwLogicIfMax 1.3.6.1.4.1.2011.5.25.41.1.13.2.1.6
Indicates the maximum port number of the specified logical interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwLogicIfTotal 1.3.6.1.4.1.2011.5.25.41.1.13.2.1.7
Indicates the maximum number of the specified logical interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwLogicIfDynamicHelpTable 1.3.6.1.4.1.2011.5.25.41.1.13.3
Logic interface dynamic help table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwLogicIfDynamicHelpEntry

hwLogicIfDynamicHelpEntry 1.3.6.1.4.1.2011.5.25.41.1.13.3.1
Logic interface dynamic help table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwLogicIfDynamicHelpEntry  

hwLogicDynamicIfhelpType 1.3.6.1.4.1.2011.5.25.41.1.13.3.1.1
Indicates the types of logical interfaces that can be queried.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ve(1), imaGroup(8), tunnel(11), mpGroup(13), dslGroup(16)  

hwLogicDynamicIfChassisNumber 1.3.6.1.4.1.2011.5.25.41.1.13.3.1.2
Indicates the ID of the chassis that that can be queried.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwLogicDynamicIfSlotNumber 1.3.6.1.4.1.2011.5.25.41.1.13.3.1.3
Indicates the ID of the slot that can be queried.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwLogicDynamicIfCardNumber 1.3.6.1.4.1.2011.5.25.41.1.13.3.1.4
Indicates the ID of the card that can be queried.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwLogicDynamicIfMin 1.3.6.1.4.1.2011.5.25.41.1.13.3.1.5
Indicates the minimum port number of the specified logical interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwLogicDynamicIfMax 1.3.6.1.4.1.2011.5.25.41.1.13.3.1.6
Indicates the maximum port number of the specified logical interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwLogicDynamicIfTotal 1.3.6.1.4.1.2011.5.25.41.1.13.3.1.7
Indicates the maximum number of the specified logical interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwCppsObjects 1.3.6.1.4.1.2011.5.25.41.1.14
OBJECT IDENTIFIER    

hwCppsGlobalEnable 1.3.6.1.4.1.2011.5.25.41.1.14.1
Whether statistic function is enabled globally, and the default value is disable.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwCppsInterfaceTable 1.3.6.1.4.1.2011.5.25.41.1.14.2
CPU packet and byte statistic interface configuration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwCppsInterfaceEntry

hwCppsInterfaceEntry 1.3.6.1.4.1.2011.5.25.41.1.14.2.1
The entry of hwCppsInterfaceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwCppsInterfaceEntry  

hwCppsInterfaceIndex 1.3.6.1.4.1.2011.5.25.41.1.14.2.1.1
Index number of the interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwCppsPortPvcEnable 1.3.6.1.4.1.2011.5.25.41.1.14.2.1.2
Whether statistic function is enabled on PVC.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwCppsPortVlanEnable 1.3.6.1.4.1.2011.5.25.41.1.14.2.1.3
Whether statistic function is enabled on VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwCppsIfStatisticsTable 1.3.6.1.4.1.2011.5.25.41.1.14.3
CPU packet and byte statistic interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwCppsIfStatisticsEntry

hwCppsIfStatisticsEntry 1.3.6.1.4.1.2011.5.25.41.1.14.3.1
The entry of hwCppsIfStatisticsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwCppsIfStatisticsEntry  

hwCppsIfStatisticsIndex 1.3.6.1.4.1.2011.5.25.41.1.14.3.1.1
Index number of the interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwCppsInterfacePktStatisic 1.3.6.1.4.1.2011.5.25.41.1.14.3.1.2
Packet statistic information of the interface sent to CPU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwCppsInterfaceByteStatisic 1.3.6.1.4.1.2011.5.25.41.1.14.3.1.3
Byte statistic information of the interface sent to CPU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwCppsResetInterfaceStatisic 1.3.6.1.4.1.2011.5.25.41.1.14.3.1.4
Whether to reset statistics.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), unreset(2)  

hwCppsAtmPvcTable 1.3.6.1.4.1.2011.5.25.41.1.14.4
CPU packet and byte statistic ATM PVC table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwCppsAtmPvcEntry

hwCppsAtmPvcEntry 1.3.6.1.4.1.2011.5.25.41.1.14.4.1
The entry of hwCppsAtmPvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwCppsAtmPvcEntry  

hwCppsAtmIfIndex 1.3.6.1.4.1.2011.5.25.41.1.14.4.1.1
Index number of the interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwCppsAtmVpi 1.3.6.1.4.1.2011.5.25.41.1.14.4.1.2
VPI.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVpIdentifier  

hwCppsAtmVci 1.3.6.1.4.1.2011.5.25.41.1.14.4.1.3
VCI.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVcIdentifier  

hwCppsAtmPvcPktStatisic 1.3.6.1.4.1.2011.5.25.41.1.14.4.1.4
Packet statistic information of the PVC sent to CPU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwCppsAtmPvcByteStatisic 1.3.6.1.4.1.2011.5.25.41.1.14.4.1.5
Byte statistic information of the PVC sent to CPU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwCppsResetAtmPvcStatisic 1.3.6.1.4.1.2011.5.25.41.1.14.4.1.6
Whether to reset statistics.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), unreset(2)  

hwCppsPortVlanTable 1.3.6.1.4.1.2011.5.25.41.1.14.5
CPU packet and byte statistic port VLAN table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwCppsPortVlanEntry

hwCppsPortVlanEntry 1.3.6.1.4.1.2011.5.25.41.1.14.5.1
The entry of hwCppsPortVlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwCppsPortVlanEntry  

hwCppsPortIndex 1.3.6.1.4.1.2011.5.25.41.1.14.5.1.1
Index number of the interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwCppsVlanId 1.3.6.1.4.1.2011.5.25.41.1.14.5.1.2
VLAN ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanIdOrNone  

hwCppsPortVlanPktStatisic 1.3.6.1.4.1.2011.5.25.41.1.14.5.1.3
Packet statistic information of the port sent to CPU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwCppsPortVlanByteStatisic 1.3.6.1.4.1.2011.5.25.41.1.14.5.1.4
Byte statistic information of the port sent to CPU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwCppsResetPortVlanStatisic 1.3.6.1.4.1.2011.5.25.41.1.14.5.1.5
Whether to reset statistics.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), unreset(2)  

hwPortIsolationGroupAttrib 1.3.6.1.4.1.2011.5.25.41.1.15
OBJECT IDENTIFIER    

hwPortIsolationGroupTable 1.3.6.1.4.1.2011.5.25.41.1.15.1
Logic interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwPortIsolationGroupEntry

hwPortIsolationGroupEntry 1.3.6.1.4.1.2011.5.25.41.1.15.1.1
Logic interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwPortIsolationGroupEntry  

hwPortIsolationGroupIndex 1.3.6.1.4.1.2011.5.25.41.1.15.1.1.1
ID of Port-Isolation-Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..63  

hwPortIsolationGroupPortList 1.3.6.1.4.1.2011.5.25.41.1.15.1.1.2
PortList of Port-Isolation-Group.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

hwPortIsolationGroupRowStatus 1.3.6.1.4.1.2011.5.25.41.1.15.1.1.3
Indicates the status of the row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwVTrunkAttr 1.3.6.1.4.1.2011.5.25.41.1.16
OBJECT IDENTIFIER    

hwVTrunkIfTable 1.3.6.1.4.1.2011.5.25.41.1.16.1
The vtrunk table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwVTrunkIfEntry

hwVTrunkIfEntry 1.3.6.1.4.1.2011.5.25.41.1.16.1.1
Entries of the vtrunk table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwVTrunkIfEntry  

hwVTrunkIfIndex 1.3.6.1.4.1.2011.5.25.41.1.16.1.1.1
The IfIndex of the VTrunk interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwVTrunkIfID 1.3.6.1.4.1.2011.5.25.41.1.16.1.1.2
The identification of the VTrunk interface.It may identify VTrunk and is an index of the interface.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwVTrunkIfType 1.3.6.1.4.1.2011.5.25.41.1.16.1.1.3
The type of the VTrunk interface includes pos-Trunk, cpos-Trunk, atm-trunk and atm-bundle.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER posTrunk(1), cposTrunk(2), atmTrunk(3), atmBundle(4)  

hwVTrunkIfRowStatus 1.3.6.1.4.1.2011.5.25.41.1.16.1.1.50
Current operation status of the row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwVTrunkMemAttr 1.3.6.1.4.1.2011.5.25.41.1.17
OBJECT IDENTIFIER    

hwVTrunkMemTable 1.3.6.1.4.1.2011.5.25.41.1.17.1
VTrunk member attribute information table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwVTrunkMemEntry

hwVTrunkMemEntry 1.3.6.1.4.1.2011.5.25.41.1.17.1.1
VTrunk member attribute information.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwVTrunkMemEntry  

hwVTrunkMemIfIndex 1.3.6.1.4.1.2011.5.25.41.1.17.1.1.1
VTrunk port index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hwVTrunkIfnetIndex 1.3.6.1.4.1.2011.5.25.41.1.17.1.1.2
The IfnetIndex of the VTrunk interface.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwVTrunkValidEntry 1.3.6.1.4.1.2011.5.25.41.1.17.1.1.3
Valid Entries of VTrunk interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

hwVTrunkOperstatus 1.3.6.1.4.1.2011.5.25.41.1.17.1.1.4
Status of operation, indicates port status. There are vtrunk_up(1) and vtrunk_down(2).It expresses whether port is shutdown.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

hwVTrunkPortActive 1.3.6.1.4.1.2011.5.25.41.1.17.1.1.5
Active port of backup-access vtrunk or not 1: portInactive 2: portActive.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER portInactive(1), portActive(2)  

hwVTrunkRowStatus 1.3.6.1.4.1.2011.5.25.41.1.17.1.1.50
Current operation status of the row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwMasterBackupTrunkSubinterfaceAttr 1.3.6.1.4.1.2011.5.25.41.1.18
OBJECT IDENTIFIER    

hwMasterBackupTrunkSubinterfaceTable 1.3.6.1.4.1.2011.5.25.41.1.18.1
Master-Backup Trunk Subinterface attribute information table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMasterBackupTrunkSubinterfaceEntry

hwMasterBackupTrunkSubinterfaceEntry 1.3.6.1.4.1.2011.5.25.41.1.18.1.1
Master-Backup Trunk Subinterface attribute information.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMasterBackupTrunkSubinterfaceEntry  

hwBackupTrunkIfIndex 1.3.6.1.4.1.2011.5.25.41.1.18.1.1.1
This object indicates index of master/backup trunk sub-interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwBackupStatus 1.3.6.1.4.1.2011.5.25.41.1.18.1.1.2
The value of this object identifies backupStatus of master/backup trunk sub-interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER init(1), master(2), backup(3)  

hwRevertiveMode 1.3.6.1.4.1.2011.5.25.41.1.18.1.1.3
The value of this object identifies revertive-mode of master/backup trunk sub-interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER revertive(1), nonRevertive(2)  

hwWtrTime 1.3.6.1.4.1.2011.5.25.41.1.18.1.1.4
The value of this object identifies the wait-to-restore time of master/backup trunk sub-interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwFlushVlanId 1.3.6.1.4.1.2011.5.25.41.1.18.1.1.5
This object indicates VLAN ID carried in a FlushPDU.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIdOrNone  

hwVaspPort 1.3.6.1.4.1.2011.5.25.41.1.19
OBJECT IDENTIFIER    

hwVaspPortPeerMacTable 1.3.6.1.4.1.2011.5.25.41.1.19.1
Vasp port peer MAC table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwVaspPortPeerMacEntry

hwVaspPortPeerMacEntry 1.3.6.1.4.1.2011.5.25.41.1.19.1.1
Vasp port peer MAC table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwVaspPortPeerMacEntry  

hwVaspPortIfIndex 1.3.6.1.4.1.2011.5.25.41.1.19.1.1.1
The index of interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwVaspPortName 1.3.6.1.4.1.2011.5.25.41.1.19.1.1.2
The name of vasp port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

hwVaspPortPeerMac 1.3.6.1.4.1.2011.5.25.41.1.19.1.1.3
The peer MAC of port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

hwIFExtTrapObjects 1.3.6.1.4.1.2011.5.25.41.1.20
OBJECT IDENTIFIER    

hwLinkDownReason 1.3.6.1.4.1.2011.5.25.41.1.20.1
The reason code of link changes.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER physicalLinkDown(1), lacpNegotiationFailed(2), receiveConfReqPacket(3), receiveConfAckPacket(4), receiveNakPacket(5), receiveTermPacket(6), receiveTermAckPacket(7), receiveCodeRejPacket(8), receiveProtoRejPacket(9), chapAuthenticationFailed(10), papAuthenticationFailed(11), keepaliveOutOfTime(12), pvcDown(13), efmSessionFailed(14), tunnelDownOrInexist(15), admindown(16), protocoldown(17), adminup(18), protocolup(19), mainifdown(20), physicalLinkIsUp(21), conditionsForActivationNotMet(22), conditionsForActivationAreMet(23), tunnelIsUp(24), interfaceIsDeleted(25), bfdSessionDown(26), bfdSessionUp(27), efmSessionUp(28), portAlarmDown(29), dldpIsDown(30), dldpIsUp(31), vrrpFlowDown(32), vrrpFlowUp(33), veFlowDown(34), veFlowUp(35), errorDown(36), crcErrorDown(37), crcErrorUp(38), transceiverSpeedMismatch(39), transceiverTypeMismatch(40), negotiationUnsupported(41)  

hwMainIfName 1.3.6.1.4.1.2011.5.25.41.1.20.2
The main interface name.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

hwCfmOverPhysicalName 1.3.6.1.4.1.2011.5.25.41.1.20.3
The configuration of the interface board or interface card is restored.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

hwIpv6IfChangeDownReason 1.3.6.1.4.1.2011.5.25.41.1.20.4
The reason code of link changes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER interfaceIsDown(1), ipv6AddressUnavailable(2), ipv6AddressAvailable(3), pppIpcp6Down(4), disableIpv6ProtocolorDeleteInterface(6)  

hwTrunkIfDescr 1.3.6.1.4.1.2011.5.25.41.1.20.5
The name of trunk interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

hwTrunkMemIfDescr 1.3.6.1.4.1.2011.5.25.41.1.20.6
The name of trunk member interface..
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

hwTrunkActiveMember 1.3.6.1.4.1.2011.5.25.41.1.20.7
The number of active trunk members.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

hwIfExtTrapReason 1.3.6.1.4.1.2011.5.25.41.1.20.8
The reason of an event.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

hwLacpOldPDUInfo 1.3.6.1.4.1.2011.5.25.41.1.20.9
The old lacp PDU field.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

hwLacpNewPDUInfo 1.3.6.1.4.1.2011.5.25.41.1.20.10
The new lacp PDU field.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

hwTrunkMapAttr 1.3.6.1.4.1.2011.5.25.41.1.21
OBJECT IDENTIFIER    

hwTrunkMapTable 1.3.6.1.4.1.2011.5.25.41.1.21.1
The trunk map table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwTrunkMapEntry

hwTrunkMapEntry 1.3.6.1.4.1.2011.5.25.41.1.21.1.1
Entries of the trunk map table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwTrunkMapEntry  

hwTrunkMapType 1.3.6.1.4.1.2011.5.25.41.1.21.1.1.1
The type of the Trunk interface includes eth-trunk and ip-trunk. The ip-trunk is only comprised by pos link, otherwise the eth-trunk is only comprised by ethernet link.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER ethTrunk(1), ipTrunk(2)  

hwTrunkMapID 1.3.6.1.4.1.2011.5.25.41.1.21.1.1.2
The identification of the Trunk interface.It may identify Trunk and is an index of the interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hwTrunkMapIndex 1.3.6.1.4.1.2011.5.25.41.1.21.1.1.3
The number of the Trunk interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwIFExtConformance 1.3.6.1.4.1.2011.5.25.41.2
OBJECT IDENTIFIER    

hwIFExtGroups 1.3.6.1.4.1.2011.5.25.41.2.1
OBJECT IDENTIFIER    

hwTrunkIfGroup 1.3.6.1.4.1.2011.5.25.41.2.1.1
A collection of objects indicating information of IP address of interface, contain IP address, IP address mask and IP address acquiring method.
Status: current Access: read-only
OBJECT-GROUP    

hwIfIpAddressGroup 1.3.6.1.4.1.2011.5.25.41.2.1.2
A collection of objects indicating attribute of the Trunk interface.
Status: current Access: read-only
OBJECT-GROUP    

hwIFExtGroup 1.3.6.1.4.1.2011.5.25.41.2.1.3
A collection of objects indicating attribute of interface extended.
Status: current Access: read-only
OBJECT-GROUP    

hwTrunkMemGroup 1.3.6.1.4.1.2011.5.25.41.2.1.4
Trunk member attribute Group, now only can set hwTrunkPortWeight and hwTrunkPortStandby. hwTrunkSelectStatus and hwTrunkDeleteFlag can't be set. These attributes are for extend.
Status: current Access: read-only
OBJECT-GROUP    

hwIFFlowStatGroup 1.3.6.1.4.1.2011.5.25.41.2.1.5
A collection of objects indicating interval time of interface flow stat.
Status: current Access: read-only
OBJECT-GROUP    

hwAdminVrrpMemberIfGroup 1.3.6.1.4.1.2011.5.25.41.2.1.6
A collection of objects indicating attribute of the interface track administrator VRRP.
Status: obsolete Access: read-only
OBJECT-GROUP    

hwIfEtherStatGroup 1.3.6.1.4.1.2011.5.25.41.2.1.7
Interface statistic Group.
Status: current Access: read-only
OBJECT-GROUP    

hwIFExtCompliances 1.3.6.1.4.1.2011.5.25.41.2.2
OBJECT IDENTIFIER    

hwIfMonitorThresholdGroup 1.3.6.1.4.1.2011.5.25.41.2.1.8
Alarm Monitor Group.
Status: current Access: read-only
OBJECT-GROUP    

hwIfMonitorGeneralGroup 1.3.6.1.4.1.2011.5.25.41.2.1.9
Alarm Monitor Enable Group.
Status: current Access: read-only
OBJECT-GROUP    

hwIfFluxLimitGroup 1.3.6.1.4.1.2011.5.25.41.2.1.10
Flux limit Group.
Status: current Access: read-only
OBJECT-GROUP    

hwIfDiffServGroup 1.3.6.1.4.1.2011.5.25.41.2.1.11
Interface statistic Group.
Status: current Access: read-only
OBJECT-GROUP    

hwIfQueryGroup 1.3.6.1.4.1.2011.5.25.41.2.1.12
Interface name Group.
Status: current Access: read-only
OBJECT-GROUP    

hwLogicIfAttrGroup 1.3.6.1.4.1.2011.5.25.41.2.1.13
Logic interface table Group.
Status: current Access: read-only
OBJECT-GROUP    

hwIfIpUnnumberedGroup 1.3.6.1.4.1.2011.5.25.41.2.1.14
Logic interface table Group.
Status: current Access: read-only
OBJECT-GROUP    

hwLinkModeChangeAutoCreateIfGroup 1.3.6.1.4.1.2011.5.25.41.2.1.15
Interface time slot Group.
Status: current Access: read-only
OBJECT-GROUP    

hwCppsGlobalEnableGroup 1.3.6.1.4.1.2011.5.25.41.2.1.16
A collection of objects indicating global CPU packet statistic function.
Status: current Access: read-only
OBJECT-GROUP    

hwCppsInterfaceGroup 1.3.6.1.4.1.2011.5.25.41.2.1.17
A collection of objects providing interface configuration function.
Status: current Access: read-only
OBJECT-GROUP    

hwCppsIfStatisticsGroup 1.3.6.1.4.1.2011.5.25.41.2.1.18
A collection of objects providing packet and byte statistic of the interface sent to CPU.
Status: current Access: read-only
OBJECT-GROUP    

hwCppsAtmPvcGroup 1.3.6.1.4.1.2011.5.25.41.2.1.19
A collection of objects providing packet and byte statistic for the pvc sent to CPU.
Status: current Access: read-only
OBJECT-GROUP    

hwCppsPortVlanGroup 1.3.6.1.4.1.2011.5.25.41.2.1.20
A collection of objects providing packet and byte statistic for the port sent to CPU.
Status: current Access: read-only
OBJECT-GROUP    

hwPortIsolationGroup 1.3.6.1.4.1.2011.5.25.41.2.1.21
Port Isolation Group.
Status: current Access: read-only
OBJECT-GROUP    

hwVTrunkIfGroup 1.3.6.1.4.1.2011.5.25.41.2.1.22
VTrunk attribute Group.
Status: current Access: read-only
OBJECT-GROUP    

hwVTrunkMemGroup 1.3.6.1.4.1.2011.5.25.41.2.1.23
VTrunk member attribute Group.
Status: current Access: read-only
OBJECT-GROUP    

hwLogicIfHelpTableGroup 1.3.6.1.4.1.2011.5.25.41.2.1.24
Logic interface help table Group.
Status: current Access: read-only
OBJECT-GROUP    

hwSubInterfaceBackupTrunkGroup 1.3.6.1.4.1.2011.5.25.41.2.1.25
SubInterfaceBackupTrunk attribute Group.
Status: current Access: read-only
OBJECT-GROUP    

hwVaspPortGroup 1.3.6.1.4.1.2011.5.25.41.2.1.26
The vasp port group.
Status: current Access: read-only
OBJECT-GROUP    

hwLogicIfDynamicHelpTableGroup 1.3.6.1.4.1.2011.5.25.41.2.1.27
Logic interface Dynamic help table Group.
Status: current Access: read-only
OBJECT-GROUP    

hwIfExtGlobalbGroup 1.3.6.1.4.1.2011.5.25.41.2.1.28
Logic interface Dynamic help table Group.
Status: current Access: read-only
OBJECT-GROUP    

hwTrunkMapGroup 1.3.6.1.4.1.2011.5.25.41.2.1.29
Tunk map group.
Status: current Access: read-only
OBJECT-GROUP    

hwIFExtCompliance 1.3.6.1.4.1.2011.5.25.41.2.2.1
The compliance statement for entities implementing Huawei extended interface management MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

hwIFExtTraps 1.3.6.1.4.1.2011.5.25.41.3
OBJECT IDENTIFIER    

hwTrunkWorkingSwitch 1.3.6.1.4.1.2011.5.25.41.3.1
hwTrunkWorkingSwitch. 1.hwTrunkIfID: The identification of the Trunk interface; 2.hwTrunkIfWorkingState: Current working state of backup-access trunk. Index: hwTrunkIndex.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLacpNegotiateFailed 1.3.6.1.4.1.2011.5.25.41.3.2
The member of LAG neither can take over PDU nor transmit PDUs. Send this trap when LACP protocol negotiation fails. 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is the name of the trunk in the ifXTable of IF-MIB. 3.ifName: It is the name of the port in the ifXTable of IF-MIB. Indexes: 1.hwTrunkIndex; 2.ifIndex.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLacpTotalLinkLoss 1.3.6.1.4.1.2011.5.25.41.3.3
Total loss of link bandwidth: it means that there is no member in the LAG group and the trap of MNCD(Member not Collecting/Distributing) occurs. 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is in the ifXTable of IF-MIB. Index: hwTrunkIndex.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLacpPartialLinkLoss 1.3.6.1.4.1.2011.5.25.41.3.4
Part loss of link bandwidth: it means that some members in the LAG group aren't in the working-state, making the number of ports in working-state smaller than the hwTrunkIfMinLinkNum. The trap of PLL(Partial Link Loss) will be restrained by the trap of TLL(Total Link Loss). 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is in the ifXTable of IF-MIB. Index: hwTrunkIndex.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfFlowDown 1.3.6.1.4.1.2011.5.25.41.3.5
This notification indicates the time when the interface's flow status changes to flow down,and the reason.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfFlowUp 1.3.6.1.4.1.2011.5.25.41.3.6
This notification indicates the time when the interface's flow status changes to flow up,and the reason.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfNameChange 1.3.6.1.4.1.2011.5.25.41.3.7
When a single-chassis device is upgraded to a multi-chassis device, the interface information is changed and then the system sends a trap.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfNameChangeResume 1.3.6.1.4.1.2011.5.25.41.3.8
When a multi-chassis restore a single-chassis device, the interface information is changed and then the system sends a trap.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwExtLinkDown 1.3.6.1.4.1.2011.5.25.41.3.9
This notification indicates the time when the member interface link status changes to down.The ifDescr indicates the name of the member interface,the hwIFExtMemberOf indicates the name of main interface.
Status: deprecated Access: read-only
NOTIFICATION-TYPE    

hwExtLinkUp 1.3.6.1.4.1.2011.5.25.41.3.10
This notification indicates the time when the member interface link status changes to up.The ifDescr indicates the name of the member interface,the hwIFExtMemberOf indicates the name of main interface.
Status: deprecated Access: read-only
NOTIFICATION-TYPE    

hwLoopbackBlock 1.3.6.1.4.1.2011.5.25.41.3.11
This notification indicates block state of the interface.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLoopbackResume 1.3.6.1.4.1.2011.5.25.41.3.12
This notification indicates normal state of the interface.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLacpNegotiateResume 1.3.6.1.4.1.2011.5.25.41.3.13
Negotiation failure alarm is resumed. 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is the name of the trunk in the ifXTable of IF-MIB. 3.ifName: It is the name of the port in the ifXTable of IF-MIB. Indexes: 1.hwTrunkIndex; 2.ifIndex.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLacpTotalLinkLossResume 1.3.6.1.4.1.2011.5.25.41.3.14
Link bandwidth lost totally is resumed. 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is in the ifXTable of IF-MIB. Index: hwTrunkIndex.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLacpPartialLinkLossResume 1.3.6.1.4.1.2011.5.25.41.3.15
Link bandwidth lost partly is resumed. 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is in the ifXTable of IF-MIB. Index: hwTrunkIndex.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwTrunkSubIfStateToMaster 1.3.6.1.4.1.2011.5.25.41.3.24
This notification indicates BackupState of the Trunk subinterface. 1.hwIfName: The identification of the Trunk subinterface; 2.hwBackupStatus: Current working state of Trunk subinterface.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwTrunkSubIfStateToSlave 1.3.6.1.4.1.2011.5.25.41.3.25
This notification indicates BackupState of the Trunk subinterface. 1.hwIfName: The identification of the Trunk subinterface; 2.hwBackupStatus: Current working state of Trunk subinterface.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtCfmOverSlot 1.3.6.1.4.1.2011.5.25.41.3.26
The hwEntityExtCfmOverSlot notification will be displayed when the configuration of an interface board is restored. The object hwCfmOverPhysicalName idicates the name of the interface board.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwEntityExtCfmOverCard 1.3.6.1.4.1.2011.5.25.41.3.27
The hwEntityExtCfmOverCard notification will be displayed when the configuration of an interface card is restored. The object hwCfmOverPhysicalName idicates the name of the interface card.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwExtAllMemberDownNotify 1.3.6.1.4.1.2011.5.25.41.3.28
This notification indicates the time when the last member interface link status changes to down. The ifName indicates the name of the Trunk interface.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwExtAllMemberDownResume 1.3.6.1.4.1.2011.5.25.41.3.29
This notification indicates the time when the first member interface link status changes to up. The ifName indicates the name of the Trunk interface.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwTrunkMemNumberChange 1.3.6.1.4.1.2011.5.25.41.3.30
The number of active trunk members changed.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfControlFlapSuppress 1.3.6.1.4.1.2011.5.25.41.3.31
This notification indicates the time when the interface's status changes from unsuppress to suppress.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfControlFlapResume 1.3.6.1.4.1.2011.5.25.41.3.32
This notification indicates the time when the interface's status changes from suppress to unsuppress.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwExtInterfaceDelete 1.3.6.1.4.1.2011.5.25.41.3.33
This notification indicates the time when the interface was deleted.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLacpPartnerExpiredLoss 1.3.6.1.4.1.2011.5.25.41.3.34
The member of LAG receive expired PDU from partner. Send this trap when LACP protocol negotiation fails. 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is the name of the trunk in the ifXTable of IF-MIB. 3.ifName: It is the name of the port in the ifXTable of IF-MIB. Indexes: 1.hwTrunkIndex; 2.ifIndex.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLacpPDUChange 1.3.6.1.4.1.2011.5.25.41.3.35
The LACP member interface's status changed from selected to unselected due to the PDU change. 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is the name of the trunk in the ifXTable of IF-MIB. 3.ifName: It is the name of the port in the ifXTable of IF-MIB. 4.hwLacpOldPDUInfo: It is the old PDU field of the port in the hwIFExtTrapObjects of hwIFExtMib. 5.hwLacpNewPDUInfo: It is the new PDU field of the port in the hwIFExtTrapObjects of hwIFExtMib. 6.hwIfExtTrapReason: It is the reason of this trap in the hwIFExtTrapObjects of hwIFExtMib. Indexes: 1.hwTrunkIndex; 2.ifIndex.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLacpPDUChangeResume 1.3.6.1.4.1.2011.5.25.41.3.36
The LACP member interface's status changed from unselected to selected. 1.hwTrunkIfID: The identification of the Trunk interface; 2.ifName: It is the name of the trunk in the ifXTable of IF-MIB. 3.ifName: It is the name of the port in the ifXTable of IF-MIB. Indexes: 1.hwTrunkIndex; 2.ifIndex.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfEfmDown 1.3.6.1.4.1.2011.5.25.41.3.37
This notification indicates that the interface status changes to EFM Down because the interface has tracked EFM session and the EFM session goes Down.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfEfmUp 1.3.6.1.4.1.2011.5.25.41.3.38
This notification indicates that the interface status changes to EFM Up because the interface has tracked EFM session and the EFM session goes Up.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwExtTrunkMemberCountExceedThreshold 1.3.6.1.4.1.2011.5.25.41.3.39
The number of members of the Eth-Trunk in LACP mode exceeded the upper threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwExtTrunkMemberCountExceedThresholdResume 1.3.6.1.4.1.2011.5.25.41.3.40
The number of members of the Eth-Trunk in LACP mode fell below the lower threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwExtTrunkWorkingStatusChange 1.3.6.1.4.1.2011.5.25.41.3.41
This notification indicates that the working status of the backup trunk changed.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfControlFlapSuppressIPv6 1.3.6.1.4.1.2011.5.25.41.3.42
This notification indicates the time when the interface's status changes from unsuppress to suppress(IPv6).
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfControlFlapResumeIPv6 1.3.6.1.4.1.2011.5.25.41.3.43
This notification indicates the time when the interface's status changes from suppress to unsuppress(IPv6).
Status: current Access: read-only
NOTIFICATION-TYPE    

hwMonitorNotifications 1.3.6.1.4.1.2011.5.25.41.4
OBJECT IDENTIFIER    

hwIfMonitorCrcErrorRising 1.3.6.1.4.1.2011.5.25.41.4.1
Crc error alarm notification
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorCrcErrorResume 1.3.6.1.4.1.2011.5.25.41.4.2
Crc error alarm resume
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorSdhErrorRising 1.3.6.1.4.1.2011.5.25.41.4.3
Sdh error alarm notification only for B3
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorSdhErrorResume 1.3.6.1.4.1.2011.5.25.41.4.4
Sdh error alarm resume only for B3
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorInputRateRising 1.3.6.1.4.1.2011.5.25.41.4.5
Input rate alarm notification
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorInputRateResume 1.3.6.1.4.1.2011.5.25.41.4.6
Input rate alarm resume
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorOutputRateRising 1.3.6.1.4.1.2011.5.25.41.4.7
Output rate alarm notification
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorOutputRateResume 1.3.6.1.4.1.2011.5.25.41.4.8
Output rate alarm resume
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorHalfDuplexRising 1.3.6.1.4.1.2011.5.25.41.4.9
Interface half duplex alarm norification
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorPauseFrameRising 1.3.6.1.4.1.2011.5.25.41.4.10
Pause frame alarm notification
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorPauseFrameRisingResume 1.3.6.1.4.1.2011.5.25.41.4.11
Pause frame alarm resume
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfPortControlUp 1.3.6.1.4.1.2011.5.25.41.4.12
Control Up alarm notification
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfPortControlDown 1.3.6.1.4.1.2011.5.25.41.4.13
Control Down alarm notification
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorSdhB1ErrorRising 1.3.6.1.4.1.2011.5.25.41.4.14
Sdh B1 error alarm notification
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorSdhB1ErrorResume 1.3.6.1.4.1.2011.5.25.41.4.15
Sdh B1 error alarm resume
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorSdhB2ErrorRising 1.3.6.1.4.1.2011.5.25.41.4.16
Sdh B2 error alarm notification
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorSdhB2ErrorResume 1.3.6.1.4.1.2011.5.25.41.4.17
Sdh B2 error alarm resume
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorSymbolErrorRising 1.3.6.1.4.1.2011.5.25.41.4.18
Symbol error alarm notification
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorSymbolErrorResume 1.3.6.1.4.1.2011.5.25.41.4.19
Crc error alarm resume
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorBadBytesErrorRising 1.3.6.1.4.1.2011.5.25.41.4.40
Description.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIfMonitorBadBytesErrorResume 1.3.6.1.4.1.2011.5.25.41.4.41
Description.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwIFExtTrapConformance 1.3.6.1.4.1.2011.5.25.41.5
OBJECT IDENTIFIER    

hwIFExtTrapGroups 1.3.6.1.4.1.2011.5.25.41.5.1
OBJECT IDENTIFIER    

hwIFExtTrapGroup 1.3.6.1.4.1.2011.5.25.41.5.1.1
IF Trap Group.
Status: current Access: read-only
NOTIFICATION-GROUP    

hwMonitorTrapGroup 1.3.6.1.4.1.2011.5.25.41.5.1.2
Monitor Trap Group.
Status: current Access: read-only
NOTIFICATION-GROUP    

hwIFIpNotifications 1.3.6.1.4.1.2011.5.25.41.6
OBJECT IDENTIFIER    

hwIfIpAddressChange 1.3.6.1.4.1.2011.5.25.41.6.1
IP Trap Group. The trap will be generated when the primary IP address of an interface changes.
Status: current Access: read-only
NOTIFICATION-TYPE