HUAWEI-L2IF-MIB
File:
HUAWEI-L2IF-MIB.mib (55799 bytes)
Imported modules
Imported symbols
Defined Types
| VlanList |
|
| Each octet within this value specifies a set of eight
vlans, with the first octet specifying vlans 0 through
7, the second octet specifying vlans 8 through 15, etc.
Within each octet, the most significant bit represents
the lowest numbered vlan, and the least significant bit
represents the highest numbered vlan. Thus, each vlan
of the link is represented by a single bit within the
value of this object. If that bit has a value of '1'
then that vlan is included in the set of vlans; the vlan
is not included if its bit has a value of '0'. |
| TEXTUAL-CONVENTION |
|
|
|
| |
OCTET STRING |
|
|
| HwL2IfEntry |
|
| SEQUENCE |
|
|
|
| |
hwL2IfPortNum |
Integer32 |
|
| |
hwL2IfPortIfIndex |
InterfaceIndex |
|
| |
hwL2IfPortType |
INTEGER |
|
| |
hwL2IfPVID |
Integer32 |
|
| |
hwL2IfIsSrcMacFilter |
TruthValue |
|
| |
hwL2IfMacAddrLearnMode |
INTEGER |
|
| |
hwL2IfMacAddressLearn |
INTEGER |
|
| |
hwL2IfBcastRatio |
Integer32 |
|
| |
hwL2IfMcastRatio |
Integer32 |
|
| |
hwL2IfUcastRatio |
Integer32 |
|
| |
hwL2IfOutBcastRatio |
Integer32 |
|
| |
hwL2IfOutMcastRatio |
Integer32 |
|
| |
hwL2IfOutUcastRatio |
Integer32 |
|
| |
hwL2IfDiscardBcast |
EnabledStatus |
|
| |
hwL2IfDiscardUnknownMcast |
EnabledStatus |
|
| |
hwL2IfDiscardUnknownUcast |
EnabledStatus |
|
| |
hwL2IfBpdu |
EnabledStatus |
|
| |
hwL2IfPortPriority |
Integer32 |
|
| |
hwL2IfPortName |
OCTET STRING |
|
| |
hwL2IfInInvalidVlanPkts |
Counter64 |
|
| |
hwL2IfFlushEnable |
EnabledStatus |
|
| |
hwL2IfFlushControlVlan |
Integer32 |
|
| |
hwL2IfCurrentInBcastPercent |
EnabledStatus |
|
| |
hwL2IfCurrentOutBcastPercent |
EnabledStatus |
|
| |
hwL2IfQinqVlanTransEnable |
EnabledStatus |
|
| |
hwL2IfQinqVlanTransMissDrop |
INTEGER |
|
| |
hwL2IfIpSubnetVlanEnable |
EnabledStatus |
|
| |
hwL2IfMacVlanEnable |
EnabledStatus |
|
| |
hwL2IfPolicyVlanEnable |
EnabledStatus |
|
| |
hwL2IfVlanPrecedence |
Integer32 |
|
| |
hwL2IfIsolateGroupEnable |
EnabledStatus |
|
| |
hwL2IfActivePortType |
INTEGER |
|
| HwL2IfHybridPortEntry |
|
| SEQUENCE |
|
|
|
| |
hwL2IfHybridPortIndex |
Integer32 |
|
| |
hwL2IfHybridTaggedVlanListLow |
VlanList |
|
| |
hwL2IfHybridTaggedVlanListHigh |
VlanList |
|
| |
hwL2IfHybridUnTaggedVlanListLow |
VlanList |
|
| |
hwL2IfHybridUnTaggedVlanListHigh |
VlanList |
|
| HwL2IfTrunkPortEntry |
|
| SEQUENCE |
|
|
|
| |
hwL2IfTrunkPortIndex |
Integer32 |
|
| |
hwL2IfTrunkAllowPassVlanListLow |
VlanList |
|
| |
hwL2IfTrunkAllowPassVlanListHigh |
VlanList |
|
| HwL2IfPortIsolateEntry |
|
| SEQUENCE |
|
|
|
| |
hwL2IfPortIsolatePortIndex |
Integer32 |
|
| |
hwL2IfPortIsolateSIName |
OCTET STRING |
|
| |
hwL2IfPortIsolateRowStatus |
RowStatus |
|
| HwL2IfSuppressionEntry |
|
| SEQUENCE |
|
|
|
| |
hwL2IfSuppressionPortIndex |
Integer32 |
|
| |
hwL2IfSuppressionType |
INTEGER |
|
| |
hwL2IfSuppressionCir |
Integer32 |
|
| |
hwL2IfSuppressionCbs |
Integer32 |
|
| |
hwL2IfSuppressionRowStatus |
RowStatus |
|
| HwL2IfVlanSuppressionEntry |
|
| SEQUENCE |
|
|
|
| |
hwL2IfVlanSuppressionPortIndex |
Integer32 |
|
| |
hwL2IfVlanSuppressionStartVlan |
Integer32 |
|
| |
hwL2IfVlanSuppressionEndVlan |
Integer32 |
|
| |
hwL2IfVlanSuppressionCir |
Integer32 |
|
| |
hwL2IfVlanSuppressionCbs |
Integer32 |
|
| |
hwL2IfVlanSuppressionRowStatus |
RowStatus |
|
| HwL2IfPortTcnEntry |
|
| SEQUENCE |
|
|
|
| |
hwL2IfTcnPortIndex |
Integer32 |
|
| |
hwL2IfTcnStp |
EnabledStatus |
|
| |
hwL2IfTcnSmartLink |
EnabledStatus |
|
| |
hwL2IfTcnVlanListLow |
OCTET STRING |
|
| |
hwL2IfTcnVlanListHigh |
OCTET STRING |
|
| HwL2IfPortLoopDetectEntry |
|
| SEQUENCE |
|
|
|
| |
hwL2IfPortLoopDetectPort |
Integer32 |
|
| |
hwL2IfPortLoopDetectEnabled |
EnabledStatus |
|
| |
hwL2IfPortLoopDetectInterval |
Integer32 |
|
| |
hwL2IfPortLoopDetectAction |
INTEGER |
|
| |
hwL2IfPortLoopDetectStatus |
INTEGER |
|
| |
hwL2IfPortLoopDetectProtocol |
OCTET STRING |
|
| HwL2IfPortProtocolVlanDataEntry |
|
| SEQUENCE |
|
|
|
| |
hwL2IfPortProtocolVlanDataPortIndex |
Integer32 |
|
| |
hwL2IfPortProtocolVlanDataVlan |
Integer32 |
|
| |
hwL2IfPortProtocolVlanDataPri |
Integer32 |
|
| |
hwL2IfPortProtocolVlanDataRowStatus |
RowStatus |
|
| HwL2IfPwSuppressionEntry |
|
| SEQUENCE |
|
|
|
| |
hwL2IfPwSuppressionVsiName |
OCTET STRING |
|
| |
hwL2IfPwSuppressionPwName |
OCTET STRING |
|
| |
hwL2IfPwSuppressionType |
INTEGER |
|
| |
hwL2IfPwSuppressionCir |
Integer32 |
|
| |
hwL2IfPwSuppressionCbs |
Integer32 |
|
| |
hwL2IfPwSuppressionRowStatus |
RowStatus |
|
| HwL2IfDynamicPortVlanEntry |
|
| SEQUENCE |
|
|
|
| |
hwL2IfDynamicPortVlanPortIndex |
Integer32 |
|
| |
hwL2IfDynamicPortVlanServiceType |
INTEGER |
|
| |
hwL2IfDynamicPortVlanPvid |
VlanIdOrNone |
|
| |
hwL2IfDynamicPortVlanUntaggedVlanListLow |
VlanList |
|
| |
hwL2IfDynamicPortVlanUntaggedVlanListHigh |
VlanList |
|
| |
hwL2IfDynamicPortVlanTaggedVlanListLow |
VlanList |
|
| |
hwL2IfDynamicPortVlanTaggedVlanListHigh |
VlanList |
|
Defined Values
| hwL2Mgmt |
1.3.6.1.4.1.2011.5.25.42 |
| OBJECT IDENTIFIER |
|
|
|
| hwL2IfMib |
1.3.6.1.4.1.2011.5.25.42.1 |
| information of layer2 interface and information of hybrid port and
information of trunk port |
| MODULE-IDENTITY |
|
|
|
| hwL2IfPortMax |
1.3.6.1.4.1.2011.5.25.42.1.1.1.1 |
| Max ports that this device supports,BRIDGE-MIB have a resemble definition. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hwL2TopologyDetect |
1.3.6.1.4.1.2011.5.25.42.1.1.1.2 |
| Whether to enable layer2 topology detection. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| hwL2IfTable |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3 |
| This is a table of layer2 interface,so it displays some attribute of
layer2 interface. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
HwL2IfEntry |
|
| hwL2IfEntry |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1 |
| Entries of extended Huawei private interface information table |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HwL2IfEntry |
|
|
| hwL2IfPortNum |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.1 |
| Number of layer2 interface port, a unique value,
for each port.It is recommended that values are assigned
contiguously starting from 1. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..65535 |
|
| hwL2IfPortIfIndex |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.2 |
| A unique value, greater than zero, for each interface or interface
sub-layer in the managed system. The value is consistent with the
ifIndex in ifTable of IF-MIB. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
InterfaceIndex |
|
|
| hwL2IfPortType |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.3 |
| Layer2 interface Port type, it contains invalid(0), trunk(1),
access(2), hybrid(3), fabric(4), qinq(5), desirable(6)
and auto(7).Do not support fabric(4) now.
invalid(0),which we read only,can't modify. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
invalid(0), trunk(1), access(2), hybrid(3), fabric(4), qinq(5), desirable(6), auto(7) |
|
| hwL2IfPVID |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.4 |
| Layer2 interface Port VLAN ID |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hwL2IfIsSrcMacFilter |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.5 |
| Whether to filter source MAC address. We don't support it now. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| hwL2IfMacAddrLearnMode |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.6 |
| Status indicates mac address learn mode of the interface.
IVL(1) means independent VLAN learning.SVL means shared VLAN learning.
We only support iVL now. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
iVL(1), sVL(2) |
|
| hwL2IfMacAddressLearn |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.7 |
| Status indicates if the interface is allowed to learn mac
address, enable(1) can be setted, (enabled(1) means that
the interface can learn mac address), otherwise disabled(2)
can be setted. discard(3) means the interface will drop packets. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2), discard(3) |
|
| hwL2IfBcastRatio |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.8 |
| Broadcast-suppression ratio. Default is 100% . 100% indicates
that the broadcast isn't suppressed. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..100 |
|
| hwL2IfMcastRatio |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.9 |
| Multicast-suppression ratio.Default is 100%, 100% indicates that
the multicast isn't suppressed. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..100 |
|
| hwL2IfUcastRatio |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.10 |
| Unicastsuppression ratio. Default is 100% , 100% indicates that
the broadcast isn't suppressed. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..100 |
|
| hwL2IfOutBcastRatio |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.11 |
| Outbound broadcast-suppression ratio. Default is 100% . 100% indicates
that the broadcast isn't suppressed. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..100 |
|
| hwL2IfOutMcastRatio |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.12 |
| Outbound multicast-suppression ratio.Default is 100%, 100% indicates that
the multicast isn't suppressed. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..100 |
|
| hwL2IfOutUcastRatio |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.13 |
| Outbound unicastsuppression ratio. Default is 100% , 100% indicates that
the broadcast isn't suppressed. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..100 |
|
| hwL2IfDiscardBcast |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.14 |
| The flag of droping the broadcast packets,
1:discard; 2:forward(default). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| hwL2IfDiscardUnknownMcast |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.15 |
| The flag of droping the unknown mutilcast packets,
1:discard; 2:forward(default). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| hwL2IfDiscardUnknownUcast |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.16 |
| The flag of droping the unknown unicast packets,
1:discard; 2:forward(default). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| hwL2IfBpdu |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.17 |
| Bpdu enable in port. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| hwL2IfPortPriority |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.18 |
| Port priority about interface. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..7 |
|
| hwL2IfPortName |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.19 |
| The interface name. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
Size(0..48) |
|
| hwL2IfFlushEnable |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.21 |
| The flush enable status of layer2 port. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| hwL2IfFlushControlVlan |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.22 |
| The control vlan of flush packet. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..4094 | 65535 |
|
| hwL2IfCurrentInBcastPercent |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.23 |
| The flag of qinq port trust default priority,
1:enable; 2:disable(default). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| hwL2IfQinqVlanTransMissDrop |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.26 |
| Packets are dropped when a VLAN translation miss occurs,
1:noDrop(default); 2:drop. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
noDrop(1), drop(2) |
|
| hwL2IfIpSubnetVlanEnable |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.27 |
| Enable VLAN assignment based on ip subnet,
1:enable(default); 2:disable. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| hwL2IfMacVlanEnable |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.28 |
| Mac Vlan enable,
1:enable; 2:disable(default) |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| hwL2IfVlanPrecedence |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.30 |
| Determine the priorities for selecting VLAN (MAC-based, subnet-based VLANs),
0:MAC VLAN(default); 1:IPSUBNET VLAN. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hwL2IfIsolateGroupEnable |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.31 |
| The value enabled(1) indicates that the port is a member of the port-isolate group; disable(2) indicates that the port is not a member of the port-isolate group. The default value is disable(2). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| hwL2IfActivePortType |
1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.32 |
| Layer2 interface active port type, it contains invalid(0), trunk(1),
access(2), hybrid(3), fabric(4), qinq(5).Do not support fabric(4) now. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
invalid(0), trunk(1), access(2), hybrid(3), fabric(4), qinq(5) |
|
| hwL2IfHybridPortEntry |
1.3.6.1.4.1.2011.5.25.42.1.1.1.9.1 |
| Entry of Hybrid-port configuration table |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HwL2IfHybridPortEntry |
|
|
| hwL2IfHybridTaggedVlanListLow |
1.3.6.1.4.1.2011.5.25.42.1.1.1.9.1.2 |
| The lowest possible value of the tagged vlan list on the
Hybrid-port. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
VlanList |
Size(256) |
|
| hwL2IfHybridTaggedVlanListHigh |
1.3.6.1.4.1.2011.5.25.42.1.1.1.9.1.3 |
| The highest possible value of the tagged vlan list on the
Hybrid-port. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
VlanList |
Size(256) |
|
| hwL2IfHybridUnTaggedVlanListLow |
1.3.6.1.4.1.2011.5.25.42.1.1.1.9.1.4 |
| The lowest possible value of the untagged vlan list on the
Hybrid-port. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
VlanList |
Size(256) |
|
| hwL2IfHybridUnTaggedVlanListHigh |
1.3.6.1.4.1.2011.5.25.42.1.1.1.9.1.5 |
| The highest possible value of the untagged vlan list on the
Hybrid-port. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
VlanList |
Size(256) |
|
| hwL2IfTrunkPortTable |
1.3.6.1.4.1.2011.5.25.42.1.1.1.10 |
| Trunk-port configuration table. Trunk-port is a logistic port. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
HwL2IfTrunkPortEntry |
|
| hwL2IfTrunkPortEntry |
1.3.6.1.4.1.2011.5.25.42.1.1.1.10.1 |
| Entry of Trunk-port configuration table |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HwL2IfTrunkPortEntry |
|
|
| hwL2IfTrunkPortIndex |
1.3.6.1.4.1.2011.5.25.42.1.1.1.10.1.1 |
| Index of Trunk-port |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..65535 |
|
| hwL2IfTrunkAllowPassVlanListLow |
1.3.6.1.4.1.2011.5.25.42.1.1.1.10.1.2 |
| The lowest possible value of the Vlan list that port Trunk allows
to pass. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
VlanList |
Size(0..256) |
|
| hwL2IfTrunkAllowPassVlanListHigh |
1.3.6.1.4.1.2011.5.25.42.1.1.1.10.1.3 |
| The highest possible value of the Vlan list that port Trunk
allows to pass. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
VlanList |
Size(0..256) |
|
| hwL2IfPortIsolateTable |
1.3.6.1.4.1.2011.5.25.42.1.1.1.11 |
| Port isolate in the same Service-instance table. The Service-instance
is used to communicate among different vlans. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
HwL2IfPortIsolateEntry |
|
| hwL2IfPortIsolateEntry |
1.3.6.1.4.1.2011.5.25.42.1.1.1.11.1 |
| Entry of port isolate configuration table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HwL2IfPortIsolateEntry |
|
|
| hwL2IfPortIsolateSIName |
1.3.6.1.4.1.2011.5.25.42.1.1.1.11.1.2 |
| The name of Service-instance.The Service-instance(S.I.)is used to
communicate among different vlans. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
Size(0..31) |
|
| hwL2IfSuppressionEntry |
1.3.6.1.4.1.2011.5.25.42.1.1.1.12.1 |
| Entry of port suppression configuration table |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HwL2IfSuppressionEntry |
|
|
| hwL2IfSuppressionType |
1.3.6.1.4.1.2011.5.25.42.1.1.1.12.1.2 |
| Type of port suppression command, a unique value from 1 to 3:
1 means broadcast suppression;
2 means multicast suppression;
3 means unicast suppression. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
broadcast(1), multicast(2), unicast(3) |
|
| hwL2IfSuppressionCir |
1.3.6.1.4.1.2011.5.25.42.1.1.1.12.1.3 |
| Committed Information Rate. Unit: kbps. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..10000000 |
|
| hwL2IfSuppressionCbs |
1.3.6.1.4.1.2011.5.25.42.1.1.1.12.1.4 |
| Committed Burst Size. Unit: byte |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
2048..64000000 |
|
| hwL2IfVlanSuppressionEntry |
1.3.6.1.4.1.2011.5.25.42.1.1.1.13.1 |
| Entry of port and Vlan suppression configuration table |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HwL2IfVlanSuppressionEntry |
|
|
| hwL2IfVlanSuppressionCir |
1.3.6.1.4.1.2011.5.25.42.1.1.1.13.1.4 |
| Committed Information Rate. Unit: kbps. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..10000000 |
|
| hwL2IfVlanSuppressionCbs |
1.3.6.1.4.1.2011.5.25.42.1.1.1.13.1.5 |
| Committed Burst Size. Unit: byte |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
2048..64000000 |
|
| hwL2IfPortTcnTable |
1.3.6.1.4.1.2011.5.25.42.1.1.1.14 |
| Port TCN in the same Service-instance table. The Service-instance
is used to configure TCN. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
HwL2IfPortTcnEntry |
|
| hwL2IfPortTcnEntry |
1.3.6.1.4.1.2011.5.25.42.1.1.1.14.1 |
| Entry of port TCN configuration table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HwL2IfPortTcnEntry |
|
|
| hwL2IfTcnPortIndex |
1.3.6.1.4.1.2011.5.25.42.1.1.1.14.1.1 |
| The port index of L2 interface. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..65535 |
|
| hwL2IfTcnStp |
1.3.6.1.4.1.2011.5.25.42.1.1.1.14.1.2 |
| Status indicates if the interface is allowed to notify stp TCN message
, enable(1) can be setted, (enabled(1) means that
the interface can notify TCN), otherwise disabled(2)
can be setted. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| hwL2IfTcnSmartLink |
1.3.6.1.4.1.2011.5.25.42.1.1.1.14.1.3 |
| Status indicates if the interface is allowed to notify SmartLink TCN message,
enable(1) can be setted, (enabled(1) means that
the interface can notify TCN), otherwise disabled(2)
can be setted. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| hwL2IfTcnVlanListLow |
1.3.6.1.4.1.2011.5.25.42.1.1.1.14.1.4 |
| The lowest possible value of the vlan list on the
Tcn-port. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
Size(0..31) |
|
| hwL2IfTcnVlanListHigh |
1.3.6.1.4.1.2011.5.25.42.1.1.1.14.1.5 |
| The highest possible value of the vlan list on the
Tcn-port. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
Size(0..31) |
|
| hwL2IfPortLoopDetectTable |
1.3.6.1.4.1.2011.5.25.42.1.1.1.15 |
| A table containing the port external loopback detection information for device.
It can protect the port from external loopback. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
HwL2IfPortLoopDetectEntry |
|
| hwL2IfPortLoopDetectEntry |
1.3.6.1.4.1.2011.5.25.42.1.1.1.15.1 |
| Entries of the port external loopback detection table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HwL2IfPortLoopDetectEntry |
|
|
| hwL2IfPortLoopDetectPort |
1.3.6.1.4.1.2011.5.25.42.1.1.1.15.1.1 |
| The port number which will be configured port external loopback detection. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hwL2IfPortLoopDetectEnabled |
1.3.6.1.4.1.2011.5.25.42.1.1.1.15.1.2 |
| When this object is set to 'enabled(1)' Port external loopback detection
is enabled on this port else disabled. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| hwL2IfPortLoopDetectAction |
1.3.6.1.4.1.2011.5.25.42.1.1.1.15.1.4 |
| The port external loopback detection protect action of this entry. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
shutdown(1), block(2), trap(3) |
|
| hwL2IfPortLoopDetectStatus |
1.3.6.1.4.1.2011.5.25.42.1.1.1.15.1.5 |
| The current status of port(block/shutdown/trap/normal). |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
normal(1), block(2), shutdown(3), trap(4) |
|
| hwL2IfPortLoopDetectProtocol |
1.3.6.1.4.1.2011.5.25.42.1.1.1.15.1.6 |
| The ethernet type of the detecting packet to port external loopback detection. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
Size(2) |
|
| hwL2IfPortProtocolVlanDataEntry |
1.3.6.1.4.1.2011.5.25.42.1.1.1.16.1 |
| The entry of protocol vlan by port. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HwL2IfPortProtocolVlanDataEntry |
|
|
| hwL2IfPwSuppressionEntry |
1.3.6.1.4.1.2011.5.25.42.1.1.1.17.1 |
| This object indicates the configuration table for PW-based unknown
traffic suppression. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HwL2IfPwSuppressionEntry |
|
|
| hwL2IfPwSuppressionVsiName |
1.3.6.1.4.1.2011.5.25.42.1.1.1.17.1.1 |
| This object indicates the name of the VSI that is configured with PW-based
unknown traffic suppression. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
Size(0..32) |
|
| hwL2IfPwSuppressionPwName |
1.3.6.1.4.1.2011.5.25.42.1.1.1.17.1.2 |
| This object indicates the name of the PW that is configured with PW-based
unknown traffic suppression. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
Size(0..16) |
|
| hwL2IfPwSuppressionType |
1.3.6.1.4.1.2011.5.25.42.1.1.1.17.1.3 |
| The value of this object identifies the type of PW-based unknown traffic suppression:
1: broadcast suppression
2: multicast suppression
3: unknown unicast suppression |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
broadcast(1), multicast(2), unicast(3) |
|
| hwL2IfPwSuppressionCir |
1.3.6.1.4.1.2011.5.25.42.1.1.1.17.1.4 |
| This object indicates the Committed Information Rate. Unit: kbit/s. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
100..1000000 |
|
| hwL2IfPwSuppressionCbs |
1.3.6.1.4.1.2011.5.25.42.1.1.1.17.1.5 |
| This object indicates the Committed Burst Size. Unit: byte. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
100..33554432 |
|
| hwL2IfPwSuppressionRowStatus |
1.3.6.1.4.1.2011.5.25.42.1.1.1.17.1.50 |
| This object indicates the RowStatus of hwPwSuppressionTable. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| hwL2IfLoopDetectInterval |
1.3.6.1.4.1.2011.5.25.42.1.1.1.18 |
| The detect period of system external loopback detection. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
5..300 |
|
| hwL2IfDynamicPortVlanEntry |
1.3.6.1.4.1.2011.5.25.42.1.1.1.19.1 |
| Entry of dynamic port-vlan relationship table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HwL2IfDynamicPortVlanEntry |
|
|
| hwL2IfDynamicPortVlanServiceType |
1.3.6.1.4.1.2011.5.25.42.1.1.1.19.1.2 |
| Service type of dynamic port-vlan relationship table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
configured(1), gvrp(2), voiceVLAN(3), unAuthenUserVLAN(4), dynAuthenVLAN(5), hvrp(6), elmi(7), macFlapping(8), loopbackDetect(9), loopDetection(10) |
|
| hwL2IfTraps |
1.3.6.1.4.1.2011.5.25.42.1.1.2 |
| OBJECT IDENTIFIER |
|
|
|
| hwL2IfInvalidVlanPacketAlarm |
1.3.6.1.4.1.2011.5.25.42.1.1.2.1 |
| Warning of receiving invalid VLAN packets in the interface. |
| Status: current |
Access: read-only |
| NOTIFICATION-TYPE |
|
|
|
| hwInBcastRisingThreshold |
1.3.6.1.4.1.2011.5.25.42.1.1.2.2 |
| Port status changed because loopback detect.(Normal/Block/Shutdown/Trap) |
| Status: current |
Access: read-only |
| NOTIFICATION-TYPE |
|
|
|
| hwL2IfMacAddrGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.1 |
| A collection of objects indicate mac address learn of the interface. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfBroadcastRatioGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.2 |
| A collection of objects indicate broadcast-suppression ratio. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfHybridTaggedVlanGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.3 |
| A collection of objects indicate lowest/highest possible value of
the tagged/untagged vlan list on the Hybrid-port. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfTrunkAllowPassVlanListGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.4 |
| A collection of objects indicate lowest/highed possible value of the
allowed and passed vlan list on the Trunk-port. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfPortGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.5 |
| A collection of objects indicate index of layer2 port. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfPVIDGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.6 |
| A collection of objects indicate PVID of layer2 interface. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfPortTypeGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.7 |
| A collection of objects indicate VLAN type of layer2 interface. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfPortMaxGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.8 |
| A collection of objects indicate that the device supports maxmum of
port . |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfPortExtGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.9 |
| A collection of objects indicate that the device supports attribute of
port . |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfPortIsolateGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.10 |
| A collection of objects indicate that the device supports islation of port . |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfAlarmGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.11 |
| A collection of objects indicate that the device supports alarm of port . |
| Status: current |
Access: read-only |
| NOTIFICATION-GROUP |
|
|
|
| hwL2IfSuppressionGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.12 |
| A collection of objects that L2IfSuppression. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfVlanSuppressionGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.13 |
| A collection of values indicate that 'Committed infomation rate'. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfPortTcnGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.14 |
| A collection of objects indicate that the device supports islation of port . |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfPortLoopDetectGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.15 |
| A collection of objects indicate that the port external loopback detection. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfPwSuppressionGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.17 |
| A collection of objects in L2IfPwSuppression. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfDynamicPortVlanTableGroup |
1.3.6.1.4.1.2011.5.25.42.1.2.2.19 |
| A collection of objects of dynamic relationship of port-vlan. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| hwL2IfCompliance |
1.3.6.1.4.1.2011.5.25.42.1.2.1.1 |
| The compliance statement for entities implementing
the Huawei layer two interface management MIB |
| Status: current |
Access: read-only |
| MODULE-COMPLIANCE |
|
|
|
| hwL2IfGroups |
1.3.6.1.4.1.2011.5.25.42.1.2.2 |
| OBJECT IDENTIFIER |
|
|
|