HUAWEI-PWE3-MIB

File: HUAWEI-PWE3-MIB.mib (119663 bytes)

Imported modules

HUAWEI-MIB HUAWEI-VPLS-EXT-MIB IF-MIB
INET-ADDRESS-MIB SNMPv2-CONF SNMPv2-MIB
SNMPv2-SMI SNMPv2-TC P-BRIDGE-MIB

Imported symbols

hwDatacomm HWL2VpnVcEncapsType HWEnableValue
HWL2VpnStateChangeReason hwL2vpnTnlType hwL2vpnTunnelIndex
InterfaceIndexOrZero ifName InetAddressType
OBJECT-GROUP MODULE-COMPLIANCE NOTIFICATION-GROUP
sysUpTime IpAddress Integer32
Unsigned32 Counter64 OBJECT-TYPE
MODULE-IDENTITY NOTIFICATION-TYPE DisplayString
TruthValue RowStatus TEXTUAL-CONVENTION
EnabledStatus

Defined Types

HWLdpPwStateChangeReason  
The type indicates the reason of LDP PW VC's status change: LDP session down (1) AC interface down (2) PSN tunnel state down (3) Mapping message not received (4) PW interface parameter not match (5) Notification not forwarding (6)
TEXTUAL-CONVENTION    
  INTEGER ldpSessionDown(1), interfaceDown(2), tunnelDown(3), receivedNoMapping(4), paraUnMatched(5), notifiNotForward(6)  

HWPWVcEntry  
SEQUENCE    
  hwPWVcID Unsigned32
  hwPWVcType HWL2VpnVcEncapsType
  hwPWVcPeerAddrType InetAddressType
  hwPWVcPeerAddr IpAddress
  hwPWVcStatus INTEGER
  hwPWVcInboundLabel Unsigned32
  hwPWVcOutboundLabel Unsigned32
  hwPWVcSwitchSign INTEGER
  hwPWVcSwitchID Unsigned32
  hwPWVcSwitchPeerAddrType InetAddressType
  hwPWVcSwitchPeerAddr IpAddress
  hwPWVcSwitchInboundLabel Unsigned32
  hwPWVcSwitchOutboundLabel Unsigned32
  hwPWVcGroupID Unsigned32
  hwPWVcIfIndex InterfaceIndexOrZero
  hwPWVcAcStatus INTEGER
  hwPWVcACOAMStatus INTEGER
  hwPWVcMtu Integer32
  hwPWVcCtrlWord HWEnableValue
  hwPWVcVCCV BITS
  hwPWVcBandWidth Unsigned32
  hwPWVcMaxAtmCells Unsigned32
  hwPWVcTnlPolicyName OCTET STRING
  hwPWVcQoSBehaviorIndex Unsigned32
  hwPWVcExplicitPathName DisplayString
  hwPWVcTemplateName OCTET STRING
  hwPWVcSecondary TruthValue
  hwPWVcUpTime Unsigned32
  hwPWOAMSync TruthValue
  hwPWVCForBfdIndex Unsigned32
  hwPWVcDelayTime Unsigned32
  hwPWVcReroutePolicy INTEGER
  hwPWVcResumeTime Unsigned32
  hwPWVcRerouteReason HWL2VpnStateChangeReason
  hwPWVcLastRerouteTime Unsigned32
  hwPWVcManualSetFault TruthValue
  hwPWVcActive TruthValue
  hwPWVcVrIfIndex InterfaceIndexOrZero
  hwPWVcVrID Unsigned32
  hwPWBFDDetectMultiplier Unsigned32
  hwPWBFDMinReceiveInterval Unsigned32
  hwPWBFDMinTransmitInterval Unsigned32
  hwPWDynamicBFDDetect TruthValue
  hwPWBFDRemoteVcID Unsigned32
  hwPWEthOamType INTEGER
  hwPWCfmMaIndex Unsigned32
  hwPWVcUpStartTime DisplayString
  hwPWVcUpSumTime Unsigned32
  hwPWVcIfName DisplayString
  hwPWVcRowStatus RowStatus
  hwPWVcAtmPackOvertime Unsigned32
  hwPWVcPwJitterBufferDepth Unsigned32
  hwPWVcPwTdmEncapsulationNum Unsigned32
  hwPWVcPwIdleCode Unsigned32
  hwPWVcPwRtpHeader Unsigned32
  hwPWVcSwitchTnlPolicyName OCTET STRING
  hwPWVcCfmMdIndex Unsigned32
  hwPWVcCfmMaName OCTET STRING
  hwPWVcCfmMdName OCTET STRING
  hwPWVcRawOrTagged INTEGER
  hwPWVcInterworkingType INTEGER
  hwPWVcCir Unsigned32
  hwPWVcPir Unsigned32
  hwPWVcQosProfile DisplayString
  hwPWVcSwitchCir Unsigned32
  hwPWVcSwitchPir Unsigned32
  hwPWVcSwitchQosProfile DisplayString
  hwPWVcTrigger TruthValue
  hwPWVcEnableACOAM EnabledStatus
  hwPWVcSwitchVrIfIndex InterfaceIndexOrZero
  hwPWVcSwitchVrID Unsigned32
  hwPWVcQosParaFromPWT INTEGER
  hwPWVcBfdParaFromPWT INTEGER
  hwPwVcNegotiateMode INTEGER
  hwPwVcIsBypass TruthValue
  hwPwVcIsAdmin TruthValue
  hwPwVcAdminPwIfIndex InterfaceIndexOrZero
  hwPwVcAdminPwLinkStatus INTEGER
  hwPwVcSwitchAdminPwIfIndex InterfaceIndexOrZero
  hwPwVcSwitchAdminPwLinkStatus INTEGER
  hwPwVcSwitchBackupAdminPwIfIndex InterfaceIndexOrZero
  hwPwVcSwitchBackupAdminPwLinkStatus INTEGER
  hwPwVcSwitchBackupVcId Unsigned32
  hwPwVcSwitchBackupVcPeerAddrType InetAddressType
  hwPwVcSwitchBackupVcPeerAddr IpAddress
  hwPwVcSwitchBackupVcReceiveLabel Unsigned32
  hwPwVcSwitchBackupVcSendLabel Unsigned32
  hwPwVcSwitchBackupVcTnlPolicyName OCTET STRING
  hwPwVcSwitchBackupVcCir Unsigned32
  hwPwVcSwitchBackupVcPir Unsigned32
  hwPwVcSwitchBackupVcQosProfile DisplayString
  hwPwVcSlaveMasterMode INTEGER
  hwPwVcSwitchVcSlaveMasterMode INTEGER
  hwPwVcSwitchBackupVcSlaveMasterMode INTEGER
  hwPwVcSwitchVcActive TruthValue
  hwPwVcSwitchBackupVcActive TruthValue
  hwPwVcSwitchCwTrans TruthValue
  hwPwVcSwitchVcServiceName OCTET STRING
  hwPwVcSwitchBackupVcServiceName OCTET STRING

HWPWVcTnlEntry  
SEQUENCE    
  hwPWVcTnlIndex Unsigned32
  hwPWVcTnlType INTEGER
  hwPWTnlForBfdIndex Unsigned32

HWPWVcStatisticsEntry  
SEQUENCE    
  hwPWVcStatisticsRcvPkts Counter64
  hwPWVcStatisticsRcvBytes Counter64
  hwPWVcStatisticsSndPkts Counter64
  hwPWVcStatisticsSndBytes Counter64

HWPWRemoteVcEntry  
SEQUENCE    
  hwPWRemoteVcID Unsigned32
  hwPWRemoteVcType HWL2VpnVcEncapsType
  hwPWRemoteVcStatus INTEGER
  hwPWRemoteVcGroupID Unsigned32
  hwPWRemoteVcMtu Unsigned32
  hwPWRemoteVcCtrlword HWEnableValue
  hwPWRemoteVcMaxAtmCells Unsigned32
  hwPWRemoteVcNotif TruthValue

HWPWVcTDMPerfCurrentEntry  
SEQUENCE    
  hwPWVcTDMPerfCurrentMissingPkts Unsigned32
  hwPWVcTDMPerfCurrentJtrBfrOverruns Unsigned32
  hwPWVcTDMPerfCurrentJtrBfrUnderruns Unsigned32
  hwPWVcTDMPerfCurrentMisOrderDropped Unsigned32
  hwPWVcTDMPerfCurrentMalformedPkt Unsigned32
  hwPWVcTDMPerfCurrentESs Unsigned32
  hwPWVcTDMPerfCurrentSESs Unsigned32
  hwPWVcTDMPerfCurrentUASs Unsigned32

HWSvcEntry  
SEQUENCE    
  hwSvcIfIndex InterfaceIndexOrZero
  hwSvcID Unsigned32
  hwSvcType HWL2VpnVcEncapsType
  hwSvcPeerAddrType InetAddressType
  hwSvcPeerAddr IpAddress
  hwSvcStatus INTEGER
  hwSvcInboundLabel Unsigned32
  hwSvcOutboundLabel Unsigned32
  hwSvcGroupID Unsigned32
  hwSvcAcStatus INTEGER
  hwSvcACOAMStatus INTEGER
  hwSvcMtu Integer32
  hwSvcCtrlWord HWEnableValue
  hwSvcVCCV BITS
  hwSvcBandWidth Unsigned32
  hwSvcMaxAtmCells Unsigned32
  hwSvcTnlPolicyName OCTET STRING
  hwSvcQoSBehaviorIndex Unsigned32
  hwSvcPWTemplateName OCTET STRING
  hwSvcUpTime Unsigned32
  hwSvcOAMSync TruthValue
  hwSvcForBfdIndex Unsigned32
  hwSvcSecondary TruthValue
  hwSvcDelayTime Unsigned32
  hwSvcReroutePolicy INTEGER
  hwSvcResumeTime Unsigned32
  hwSvcRerouteReason HWL2VpnStateChangeReason
  hwSvcLastRerouteTime Unsigned32
  hwSvcManualSetFault TruthValue
  hwSvcActive TruthValue
  hwSvcUpStartTime DisplayString
  hwSvcUpSumTime Unsigned32
  hwSvcAtmPackOvertime Unsigned32
  hwSvcPwJitterBufferDepth Unsigned32
  hwSvcPwTdmEncapsulationNum Unsigned32
  hwSvcPwIdleCode Unsigned32
  hwSvcPwRtpHeader Unsigned32
  hwSvcRawOrTagged INTEGER
  hwSvcInterworkingType INTEGER
  hwSvcCir Unsigned32
  hwSvcPir Unsigned32
  hwSvcQosProfile DisplayString
  hwSvcRowStatus RowStatus

HWSvcTnlEntry  
SEQUENCE    
  hwSvcTnlIndex Unsigned32
  hwSvcTnlType INTEGER
  hwSvcTnlForBfdIndex Unsigned32

HWSvcStatisticsEntry  
SEQUENCE    
  hwSvcStatisticsRcvPkts Counter64
  hwSvcStatisticsRcvBytes Counter64
  hwSvcStatisticsSndPkts Counter64
  hwSvcStatisticsSndBytes Counter64

HWPWTemplateEntry  
SEQUENCE    
  hwPWTemplateName OCTET STRING
  hwPWTemplatePeerAddrType InetAddressType
  hwPWTemplatePeerAddr IpAddress
  hwPWTemplateCtrlword HWEnableValue
  hwPWTemplateVCCV BITS
  hwPWTemplateFrag TruthValue
  hwPWTemplateBandwidth Integer32
  hwPWTemplateTnlPolicyName OCTET STRING
  hwPWTemplateQoSBehaviorIndex Integer32
  hwPWTemplateExplicitPathName OCTET STRING
  hwPWTemplateBFDDetectMultiplier Unsigned32
  hwPWTemplateBFDMinReceiveInterval Unsigned32
  hwPWTemplateBFDMinTransmitInterval Unsigned32
  hwPWTemplateDynamicBFDDetect TruthValue
  hwPWTemplateMaxAtmCells Unsigned32
  hwPWTemplateAtmPackOvertime Unsigned32
  hwPWTemplatePwJitterBufferDepth Unsigned32
  hwPWTemplatePwTdmEncapsulationNum Unsigned32
  hwPWTemplatePwIdleCode Unsigned32
  hwPWTemplatePwRtpHeader Unsigned32
  hwPWTemplatePwCCSeqEnable HWEnableValue
  hwPWTemplateCir Unsigned32
  hwPWTemplatePir Unsigned32
  hwPWTemplateQosProfile DisplayString
  hwPWTemplateFlowLabel EnabledStatus
  hwPWTemplateRowStatus RowStatus

HWPWEntry  
SEQUENCE    
  hwPWId Unsigned32
  hwPWType HWL2VpnVcEncapsType
  hwPWPeerIp IpAddress
  hwPWInterfaceIndex InterfaceIndexOrZero

Defined Values

hwL2VpnPwe3 1.3.6.1.4.1.2011.5.25.119.4
The HUAWEI-PWE3-MIB contains objects to manage PWE3.
MODULE-IDENTITY    

hwL2Vpn 1.3.6.1.4.1.2011.5.25.119
OBJECT IDENTIFIER    

hwPwe3MIBObjects 1.3.6.1.4.1.2011.5.25.119.4.1
OBJECT IDENTIFIER    

hwPwe3Objects 1.3.6.1.4.1.2011.5.25.119.4.1.1
OBJECT IDENTIFIER    

hwPWVcTable 1.3.6.1.4.1.2011.5.25.119.4.1.1.1
This table is the VC configuration table. Users can create or delete a VC by it.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWPWVcEntry

hwPWVcEntry 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1
Provides the information of a VC entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWPWVcEntry  

hwPWVcID 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.1
Index for the conceptual row identifying a PW within this PW Emulation table.Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element'.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

hwPWVcType 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.2
The type of the Virtual Circuit.This value indicate the service to be carried over this PW.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWL2VpnVcEncapsType  

hwPWVcPeerAddrType 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.3
Denotes the address type of the peer node. It should be set to 'unknown' if PE/PW maintenance protocol is not used and the address is unknown. Currently, support 'ipv4' only.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

hwPWVcPeerAddr 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.4
This object contain the value of the peer node address of the PW/PE maintenance protocol entity. This object SHOULD contain a value of all zeroes if not applicable (hwPWVcPeerAddrType is 'unknown').
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hwPWVcStatus 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.5
Indicates the status of the PW in the local node. Currently, can't support 'plugout'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), plugout(3), backup(4)  

hwPWVcInboundLabel 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.6
For ldp vc, the value will be created by system automatically.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWVcOutboundLabel 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.7
For ldp vc, the value will be created by system automatically.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWVcSwitchSign 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.8
The sign of switch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER staticTostatic(1), ldpTostatic(2), ldpToldp(3), upe(4)  

hwPWVcSwitchID 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.9
Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element' of the switch PW.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWVcSwitchPeerAddrType 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.10
Denotes the address type of the peer node of the switch PW. It should be set to 'unknown' if PE/PW maintenance protocol is not used and the address is unknown. Currently, support 'ipv4' only.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

hwPWVcSwitchPeerAddr 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.11
This object contain the value of the peer node address of the switch PW of the PW/PE maintenance protocol entity. This object SHOULD contain a value of all zeroes if not applicable (hwPWVcSwitchPeerAddrType is 'unknown').
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hwPWVcSwitchInboundLabel 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.12
For ldp vc, the value will be created by system automatically.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWVcSwitchOutboundLabel 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.13
For ldp vc, the value will be created by system automatically.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWVcGroupID 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.14
Used in the Group ID field sent to the peer PWES within the maintenance protocol used for PW setup. Applicable if pwVcOwner equal 'pwIdFecSignaling' or 'l2tpControlProtocol', should be set to zero otherwise. Currently, this value always be zero.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWVcIfIndex 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.15
Index of the interface (or the virtual interface) associated with the PW.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

hwPWVcAcStatus 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.16
Local AC status. Currently, can't support 'plugout'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), plugout(3), notify(4), notifyDown(5), downNotify(6)  

hwPWVcACOAMStatus 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.17
Denotes the AC's protocol is operational or not.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

hwPWVcMtu 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.18
If not equal zero, the optional Mtu object in the signaling protocol will be sent with this value, representing the locally supported MTU size over the interface (or the virtual interface) associated with the PW.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0 | 46..9600  

hwPWVcCtrlWord 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.19
If signaling is used for PW establishment, this object indicates the status of the control word negotiation, and in both signaling or manual configuration indicates if CW is to be present or not for this PW.
Status: current Access: read-create
OBJECT-TYPE    
  HWEnableValue  

hwPWVcVCCV 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.20
Indicates the optional VCCV capabilities of the PW. According to whether the control word is enabled, the value can be ccCw(0)|ccAlert(1)|ccTtl(6)|cvLspping(4)|cvBfd(5) or ccAlert(1)|ccTtl(6)|cvLspping(4)|cvBfd(5). The default value is ccAlert(1)|ccTtl(6)|cvLspping(4)|cvBfd(5).
Status: current Access: read-create
OBJECT-TYPE    
  BITS ccCw(0), ccAlert(1), ccLabel(2), cvIcmpping(3), cvLspping(4), cvBfd(5), ccTtl(6)  

hwPWVcBandWidth 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.21
This object indicates the bandwidth. '0' is the default value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..32000000  

hwPWVcMaxAtmCells 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.22
Indicates the max cell supported when vc type is atm.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..28  

hwPWVcTnlPolicyName 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.23
Indicates the tunnel policy name used.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..39)  

hwPWVcQoSBehaviorIndex 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.24
Indicates the traffic behavior Index when QOS is implemented. Currently,can't support.Return the default value is '0'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWVcExplicitPathName 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.25
Indicates the explicit path name set by the operator.Currently, can't support.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

hwPWVcTemplateName 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.26
Indicates the PW template index referenced.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..19)  

hwPWVcSecondary 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.27
Indicates whether or not the secondary PW is used.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

hwPWVcUpTime 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.28
Indicates the duration when the PW keeps Up for the last time, in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPWOAMSync 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.29
Denotes the AC and PSN are enable or not.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

hwPWVCForBfdIndex 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.30
The index of PW for BFD.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPWVcDelayTime 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.31
The reroute delay time.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWVcReroutePolicy 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.32
Reroute policy.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER delay(1), immediately(2), never(3), none(4), err(5), invalid(6), immediatelySwitch(7)  

hwPWVcResumeTime 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.33
The reroute resume time.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWVcRerouteReason 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.34
Last reroute reason.
Status: current Access: read-only
OBJECT-TYPE    
  HWL2VpnStateChangeReason  

hwPWVcLastRerouteTime 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.35
Last reroute time.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPWVcManualSetFault 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.36
Denotes the manual has been set fault or not.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

hwPWVcActive 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.37
Denotes the current vc is active or not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hwPWVcVrIfIndex 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.38
Denotes the VRRP interface this PW binding to.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

hwPWVcVrID 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.39
Denotes the VrID this PW binding to.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255  

hwPWBFDDetectMultiplier 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.40
The multiple of detection time.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 3..50  

hwPWBFDMinReceiveInterval 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.41
The interval of bfd messages to be received.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 3..1000  

hwPWBFDMinTransmitInterval 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.42
The interval of bfd messages to be sent.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 3..1000  

hwPWDynamicBFDDetect 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.43
This value indicates the capacitability to support dynamic BFD detect.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

hwPWBFDRemoteVcID 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.44
In the multiple-hop model, the value of remote VC id.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hwPWEthOamType 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.45
This value indicates the type of ETH OAM.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ethOam1ag(1), ethOam3ah(2), noEthOamCfg(3)  

hwPWCfmMaIndex 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.46
This value indicates the current CFM MA index.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4095 | 4294967295  

hwPWVcUpStartTime 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.47
Specifies the time this PW status was Up(1).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

hwPWVcUpSumTime 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.48
Indicates the accumulated time when the VC is Up, in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPWVcIfName 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.49
Name of the interface (or the virtual interface) associated with the PW.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

hwPWVcRowStatus 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.51
RowStatus for this Table. Restriction: The row must be created by 'createAndGo' handle only. Handle 'createAndWait' is forbidden. Not support modifying configuration.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwPWVcAtmPackOvertime 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.52
Specifies the AtmPackOvertime.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 100..50000  

hwPWVcPwJitterBufferDepth 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.53
Specifies the PwJitterBufferDepth.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..64  

hwPWVcPwTdmEncapsulationNum 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.54
Specifies the PwTdmEncapsulationNum.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..40  

hwPWVcPwIdleCode 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.55
Specifies the PwIdleCode.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255 | 65535  

hwPWVcPwRtpHeader 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.56
Specifies the PwRtpHeader.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWVcSwitchTnlPolicyName 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.57
Indicates the switch tunnel policy name used.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..39)  

hwPWVcCfmMdIndex 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.58
This value indicates the current CFM MD index.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4095 | 4294967295  

hwPWVcCfmMaName 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.59
This value indicates the current CFM MA name used.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..43)  

hwPWVcCfmMdName 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.60
This value indicates the current CFM MD name used.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..43)  

hwPWVcRawOrTagged 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.61
Specifies whether the raw or tagged is configured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER raw(1), tagged(2), rawTagNotConfiged(3)  

hwPWVcInterworkingType 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.62
Specifies the interworking type of the VC entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ipInterWorking(1), ipLayer2(2), ipUnknown(3)  

hwPWVcCir 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.63
Specifies the committed information rate, based on the VC entry.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWVcPir 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.64
Specifies the peak information rate, based on the VC entry.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWVcQosProfile 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.65
Specifies the QoS profile's name, based on the VC entry.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..63)  

hwPWVcSwitchCir 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.66
Specifies the committed information rate, based on the switch VC entry.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWVcSwitchPir 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.67
Specifies the peak information rate, based on the switch VC entry.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWVcSwitchQosProfile 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.68
Specifies the QoS profile's name, based on the switch VC entry.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..63)  

hwPWVcTrigger 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.69
Specifies whether the PW remote interface shutdown or not.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

hwPWVcEnableACOAM 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.70
Specifies whether ACOAM detection and notification are all enabled or not.
Status: current Access: read-create
OBJECT-TYPE    
  EnabledStatus  

hwPWVcSwitchVrIfIndex 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.71
Denotes the VRRP interface the switch PW binding to.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

hwPWVcSwitchVrID 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.72
Denotes the VrID the switch PW binding to.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255  

hwPWVcQosParaFromPWT 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.73
This object indicates the configuration of the Qos parameters managed through command line or PW template.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER cliOrMib(1), pwTemplate(2), unknown(3)  

hwPWVcBfdParaFromPWT 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.74
This object indicates the configuration of the Bfd parameters managed through command line or PW template.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER cliOrMib(1), pwTemplate(2), unknown(3)  

hwPwVcNegotiateMode 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.75
This object indicates the negotiation mode of the PW on the local node.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER slaveOrMaster(1), independent(2), unknown(3), frr(4)  

hwPwVcIsBypass 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.76
This object indicates whether the PW is the bypass PW.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

hwPwVcIsAdmin 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.77
This object indicates whether the PW is the administrator PW.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

hwPwVcAdminPwIfIndex 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.78
This object indicates the index of the interface on which the administrator PW resides after it is being tracked by the service PW.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

hwPwVcAdminPwLinkStatus 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.79
This object indicates the status of the administrator PW after it is being tracked by the service PW.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), unknown(3)  

hwPwVcSwitchAdminPwIfIndex 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.80
This object indicates the index of the interface on which the administrator PW resides after it is being tracked by the switch PW.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

hwPwVcSwitchAdminPwLinkStatus 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.81
This object indicates the status of the administrator PW after it is being tracked by the switch PW.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), unknown(3)  

hwPwVcSwitchBackupAdminPwIfIndex 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.82
This object indicates the index of the interface on which the administrator PW resides after it is being tracked by the switch backup PW.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

hwPwVcSwitchBackupAdminPwLinkStatus 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.83
This object indicates the status of the administrator PW after it is being tracked by the switch backup PW.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), unknown(3)  

hwPwVcSwitchBackupVcId 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.84
This object indicates the VC ID of the switch backup PW.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPwVcSwitchBackupVcPeerAddrType 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.85
This object indicates type of the IP address of the peer on the switch backup PW. Currently, only IPv4 addresss are supported.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

hwPwVcSwitchBackupVcPeerAddr 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.86
This object indicates the IP address of the peer on the switch backup PW.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hwPwVcSwitchBackupVcReceiveLabel 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.87
This object indicates the inbound label of the switch backup VC. For a static VC, the value of the inbound label ranges from 16 to 1023. For a dynamic VC, the inbound label is automatically generated by the system.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPwVcSwitchBackupVcSendLabel 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.88
This object indicates the outbound label of the switch backup VC. For a static VC, the value of the outbound label ranges from 0 to 1048575. For a dynamic VC, the outbound label is automatically generated by the system.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPwVcSwitchBackupVcTnlPolicyName 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.89
This object indicates the name of the tunnel policy of the switch backup VC.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..19)  

hwPwVcSwitchBackupVcCir 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.90
This object indicates the CIR of the switch backup VC.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPwVcSwitchBackupVcPir 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.91
This object indicates the PIR of the switch backup VC.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPwVcSwitchBackupVcQosProfile 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.92
This object indicates the name of the QoS profile of the switch backup VC.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..63)  

hwPwVcSlaveMasterMode 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.93
This object indicates whether the status of the VC is master or slave.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER slave(1), master(2), unknown(3), bypass(4)  

hwPwVcSwitchVcSlaveMasterMode 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.94
This object indicates whether the status of the switch VC is master or slave.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER slave(1), master(2), unknown(3)  

hwPwVcSwitchBackupVcSlaveMasterMode 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.95
This object indicates whether the status of the switch backup VC is master or slave.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER slave(1), master(2), unknown(3)  

hwPwVcSwitchVcActive 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.96
This object indicates whether the status of the switch VC is active or not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hwPwVcSwitchBackupVcActive 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.97
This object indicates whether the status of the switch backup VC is active or not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hwPwVcSwitchCwTrans 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.98
This object indicates whether the SPE support Control Word Transparent or not,default is false.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

hwPwVcSwitchVcServiceName 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.99
This object indicates the service name of the switch VC.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..100)  

hwPwVcSwitchBackupVcServiceName 1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.100
This object indicates the service name of the switch backup VC.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..100)  

hwPWVcTnlTable 1.3.6.1.4.1.2011.5.25.119.4.1.1.2
This table is used to search the tunnel index of a VC.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWPWVcTnlEntry

hwPWVcTnlEntry 1.3.6.1.4.1.2011.5.25.119.4.1.1.2.1
Provides the information of a VC tunnel entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWPWVcTnlEntry  

hwPWVcTnlIndex 1.3.6.1.4.1.2011.5.25.119.4.1.1.2.1.1
This object indicates the tunnel index of the VC.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

hwPWVcTnlType 1.3.6.1.4.1.2011.5.25.119.4.1.1.2.1.2
This object indicates the tunnel type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER lsp(1), gre(2), ipsec(3), crLsp(4)  

hwPWTnlForBfdIndex 1.3.6.1.4.1.2011.5.25.119.4.1.1.2.1.3
This object indicates the index of LSP for BFD.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPWVcStatisticsTable 1.3.6.1.4.1.2011.5.25.119.4.1.1.3
This table contains the Pwe3's VC packets statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWPWVcStatisticsEntry

hwPWVcStatisticsEntry 1.3.6.1.4.1.2011.5.25.119.4.1.1.3.1
Provides the information of the Pwe3's VC packets statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWPWVcStatisticsEntry  

hwPWVcStatisticsRcvPkts 1.3.6.1.4.1.2011.5.25.119.4.1.1.3.1.1
The total number of packets received on this VC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwPWVcStatisticsRcvBytes 1.3.6.1.4.1.2011.5.25.119.4.1.1.3.1.2
The total number of bytes received on this VC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwPWVcStatisticsSndPkts 1.3.6.1.4.1.2011.5.25.119.4.1.1.3.1.3
The total number of packets sent on this VC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwPWVcStatisticsSndBytes 1.3.6.1.4.1.2011.5.25.119.4.1.1.3.1.4
The total number of bytes sent on the VC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwPWRemoteVcTable 1.3.6.1.4.1.2011.5.25.119.4.1.1.4
This table provides remote PW information for each local PW.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWPWRemoteVcEntry

hwPWRemoteVcEntry 1.3.6.1.4.1.2011.5.25.119.4.1.1.4.1
An entry in this table is created by the agent for every PW.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWPWRemoteVcEntry  

hwPWRemoteVcID 1.3.6.1.4.1.2011.5.25.119.4.1.1.4.1.1
Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element' of the remote PW.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPWRemoteVcType 1.3.6.1.4.1.2011.5.25.119.4.1.1.4.1.2
This value indicate the service to be carried over the remote PW.
Status: current Access: read-only
OBJECT-TYPE    
  HWL2VpnVcEncapsType  

hwPWRemoteVcStatus 1.3.6.1.4.1.2011.5.25.119.4.1.1.4.1.3
Indicates the forwarding status of the remote VC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), plugout(3)  

hwPWRemoteVcGroupID 1.3.6.1.4.1.2011.5.25.119.4.1.1.4.1.4
Indicates the Group ID field of the remote PW. Currently, this value always be zero.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPWRemoteVcMtu 1.3.6.1.4.1.2011.5.25.119.4.1.1.4.1.5
Indicates the supported MTU size of the remote PW.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0 | 46..9600  

hwPWRemoteVcCtrlword 1.3.6.1.4.1.2011.5.25.119.4.1.1.4.1.6
Indicates the control word capability of the remote PW.
Status: current Access: read-only
OBJECT-TYPE    
  HWEnableValue  

hwPWRemoteVcMaxAtmCells 1.3.6.1.4.1.2011.5.25.119.4.1.1.4.1.7
Indicates the max cell supported of the remote PW when vctype is atm.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

hwPWRemoteVcNotif 1.3.6.1.4.1.2011.5.25.119.4.1.1.4.1.8
Indicates notification is supported by the remote PW.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hwPWVcSwitchNotifEnable 1.3.6.1.4.1.2011.5.25.119.4.1.1.5
If this object is set to enable(1), then it enables the emission of hwPWVcSwitchWtoP and hwPWVcSwitchPtoW notifications; otherwise these notifications are not emitted. The default value is disable (2).
Status: current Access: read-write
OBJECT-TYPE    
  HWEnableValue  

hwPWVcUpDownNotifEnable 1.3.6.1.4.1.2011.5.25.119.4.1.1.6
This object indicates the enable sign of PW VC state change notification. The default value is disable (2).
Status: current Access: read-write
OBJECT-TYPE    
  HWEnableValue  

hwPWVcDeletedNotifEnable 1.3.6.1.4.1.2011.5.25.119.4.1.1.7
This object indicates the enable sign of PW VC deletion notification. The default value is disable (2).
Status: current Access: read-write
OBJECT-TYPE    
  HWEnableValue  

hwPWVcStateChangeReason 1.3.6.1.4.1.2011.5.25.119.4.1.1.8
This object indicates the reason of PE VC state change.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  HWL2VpnStateChangeReason  

hwPWVcSwitchRmtID 1.3.6.1.4.1.2011.5.25.119.4.1.1.9
This object indicates the VC ID of PW switch between working PW and protect PW .
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

hwLdpPWStateChangeReason 1.3.6.1.4.1.2011.5.25.119.4.1.1.10
This object indicates the reason of LDP PW VC's state change.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  HWLdpPwStateChangeReason  

hwPWVcTDMPerfCurrentTable 1.3.6.1.4.1.2011.5.25.119.4.1.1.11
This table provides per TDM PW performance information. The contents of this table entry are reset to zero and gotten new information every 15 minutes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWPWVcTDMPerfCurrentEntry

hwPWVcTDMPerfCurrentEntry 1.3.6.1.4.1.2011.5.25.119.4.1.1.11.1
An entry in this table is created by the agent for every TDM PW entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWPWVcTDMPerfCurrentEntry  

hwPWVcTDMPerfCurrentMissingPkts 1.3.6.1.4.1.2011.5.25.119.4.1.1.11.1.1
Number of missing packets (as detected via control word sequence number gaps).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPWVcTDMPerfCurrentJtrBfrOverruns 1.3.6.1.4.1.2011.5.25.119.4.1.1.11.1.2
Number of times the jitter buffer was overrun.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPWVcTDMPerfCurrentJtrBfrUnderruns 1.3.6.1.4.1.2011.5.25.119.4.1.1.11.1.3
Number of times a packet needed to be played out and the jitter buffer was empty.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPWVcTDMPerfCurrentMisOrderDropped 1.3.6.1.4.1.2011.5.25.119.4.1.1.11.1.4
Number of packets detected out of order (via control word sequence numbers) that could not be re-ordered or could not fit in the jitter buffer.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPWVcTDMPerfCurrentMalformedPkt 1.3.6.1.4.1.2011.5.25.119.4.1.1.11.1.5
Number of packets detected with unexpected size or bad headers' stack.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPWVcTDMPerfCurrentESs 1.3.6.1.4.1.2011.5.25.119.4.1.1.11.1.6
The counter associated with the number of Error Seconds encountered. Any malformed packet, sequence error, LOPS, and the like are considered as Error Seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPWVcTDMPerfCurrentSESs 1.3.6.1.4.1.2011.5.25.119.4.1.1.11.1.7
The counter associated with the number of Severely Error Seconds encountered.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPWVcTDMPerfCurrentUASs 1.3.6.1.4.1.2011.5.25.119.4.1.1.11.1.8
The counter associated with the number of Unavailable Seconds encountered. Any consecutive ten seconds of SES are counted as one Unavailable Seconds (UAS).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwPwe3MIBTraps 1.3.6.1.4.1.2011.5.25.119.4.1.2
OBJECT IDENTIFIER    

hwPWVcSwitchWtoP 1.3.6.1.4.1.2011.5.25.119.4.1.2.1
This notification is generated when switch from working PW to protect PW happens.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwPWVcSwitchPtoW 1.3.6.1.4.1.2011.5.25.119.4.1.2.2
This notification is generated when switch from protect PW to working PW happens.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwPWVcDown 1.3.6.1.4.1.2011.5.25.119.4.1.2.3
This notification indicates the VC's state changes to down.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwPWVcUp 1.3.6.1.4.1.2011.5.25.119.4.1.2.4
This notification indicates the VC's state changes to up.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwPWVcDeleted 1.3.6.1.4.1.2011.5.25.119.4.1.2.5
This notification indicates the VC is deleted.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwPWVcBackup 1.3.6.1.4.1.2011.5.25.119.4.1.2.6
This notification indicates the VC's state changes to backup.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLdpPWVcDown 1.3.6.1.4.1.2011.5.25.119.4.1.2.7
This notification indicates the LDP PW VC's state changes to down.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwLdpPWVcUp 1.3.6.1.4.1.2011.5.25.119.4.1.2.8
This notification indicates the Ldp PW VC's state changes to up.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwPWVcStatusChange 1.3.6.1.4.1.2011.5.25.119.4.1.2.9
This notification indicates the VC's Active state changed.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwVpwsPwRedundancyDegraded 1.3.6.1.4.1.2011.5.25.119.4.1.2.10
VPWS PW redundancy reported a protect degraded alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwVpwsPwRedundancyDegradedClear 1.3.6.1.4.1.2011.5.25.119.4.1.2.11
VPWS PW redundancy reported the clearing of the protect degraded alarm.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwSvcObjects 1.3.6.1.4.1.2011.5.25.119.4.1.3
OBJECT IDENTIFIER    

hwSvcTable 1.3.6.1.4.1.2011.5.25.119.4.1.3.1
This table is the SVC configuration table. Users can create or delete a SVC by it.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWSvcEntry

hwSvcEntry 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1
Provides the information of a SVC entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWSvcEntry  

hwSvcIfIndex 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.1
Index of the interface (or the virtual interface) associated with the PW.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndexOrZero  

hwSvcID 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.2
Index for the conceptual row identifying a PW within this PW Emulation table.Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwSvcType 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.3
Index for the conceptual row identifying a PW within this PW Emulation table.This value indicate the service to be carried over this PW.
Status: current Access: read-create
OBJECT-TYPE    
  HWL2VpnVcEncapsType  

hwSvcPeerAddrType 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.4
Denotes the address type of the peer node. It should be set to 'unknown' if PE/PW maintenance protocol is not used and the address is unknown. Currently, support 'ipv4' only.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

hwSvcPeerAddr 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.5
This object contain the value of the peer node address of the PW/PE maintenance protocol entity. This object SHOULD contain a value of all zeroes if not applicable (hwSvcPeerAddrType is 'unknown').
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hwSvcStatus 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.6
Indicates the status of the PW in the local node. Currently, can't support 'plugout'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), plugout(3)  

hwSvcInboundLabel 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.7
This object indicates the inbound label.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwSvcOutboundLabel 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.8
This object indicates the outbound label.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwSvcGroupID 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.9
Used in the Group ID field sent to the peer PWES within the maintenance protocol used for PW setup. Applicable if SvcOwner equal 'pwIdFecSignaling' or 'l2tpControlProtocol', should be set to zero otherwise. Currently, this value always be zero.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwSvcAcStatus 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.10
Local AC status. Currently, can't support 'plugout'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), plugout(3)  

hwSvcACOAMStatus 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.11
Denotes the AC's protocol is operational or not.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

hwSvcMtu 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.12
If not equal zero, the optional Mtu object in the signaling protocol will be sent with this value, representing the locally supported MTU size over the interface (or the virtual interface) associated with the PW.Currently, can't support.'0' is the default value.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0 | 46..9600  

hwSvcCtrlWord 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.13
If signaling is used for PW establishment, this object indicates the status of the control word negotiation, and in both signaling or manual configuration indicates if CW is to be present or not for this PW.
Status: current Access: read-create
OBJECT-TYPE    
  HWEnableValue  

hwSvcVCCV 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.14
Indicates the optional VCCV capabilities of the SVC. According to whether the control word is enabled, the value can be ccCw(0)|ccAlert(1)|cvLspping(4)|cvBfd(5) or ccAlert(1)|cvLspping(4)|cvBfd(5). The default value is ccAlert(1)|cvLspping(4)|cvBfd(5).
Status: current Access: read-create
OBJECT-TYPE    
  BITS ccCw(0), ccAlert(1), ccLabel(2), cvIcmpping(3), cvLspping(4), cvBfd(5)  

hwSvcBandWidth 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.15
This object indicates the bandwidth.Currently, can't support.'0' is the default value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..32000000  

hwSvcMaxAtmCells 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.16
Indicates the max cell supported when vc type is atm.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..28  

hwSvcTnlPolicyName 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.17
Indicates the tunnel policy name used.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..39)  

hwSvcQoSBehaviorIndex 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.18
Indicates the traffic behavior Index when QOS is implemented. Currently, can't support.'0' is the default value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwSvcPWTemplateName 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.19
Indicates the PW template index referenced.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..19)  

hwSvcUpTime 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.20
Indicates the duration when the SVC keeps Up for the last time, in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwSvcOAMSync 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.21
Denotes the AC and PSN are enable or not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hwSvcForBfdIndex 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.22
The index of PW for BFD.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwSvcSecondary 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.23
Indicates whether or not the secondary PW is used.Currently, can't support.Return the default value is 'false'.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

hwSvcDelayTime 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.24
The reroute delay time.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwSvcReroutePolicy 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.25
Reroute policy.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER delay(1), immediately(2), never(3), none(4), err(5), invalid(6)  

hwSvcResumeTime 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.26
The reroute resume time.Currently, can't support.Return the default value is '0'.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwSvcRerouteReason 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.27
Last reroute reason.
Status: current Access: read-only
OBJECT-TYPE    
  HWL2VpnStateChangeReason  

hwSvcLastRerouteTime 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.28
Last reroute time.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwSvcManualSetFault 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.29
Denotes the manual has been set fault or not.Currently, can't support.Return the default value is 'false'.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hwSvcActive 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.30
Denotes the current vc is active or not.Currently, can't support.Return the default value is 'false'.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hwSvcUpStartTime 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.31
Specifies the time this PW status was Up(1).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

hwSvcUpSumTime 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.32
Indicates the accumulated time when the SVC is Up, in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwSvcAtmPackOvertime 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.33
Specifies the AtmPackOvertime.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 100..50000  

hwSvcPwJitterBufferDepth 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.34
Specifies the PwJitterBufferDepth.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..64  

hwSvcPwTdmEncapsulationNum 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.35
Specifies the PwTdmEncapsulationNum.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..40  

hwSvcPwIdleCode 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.36
Specifies the PwIdleCode.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255 | 65535  

hwSvcPwRtpHeader 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.37
Specifies the PwRtpHeader.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwSvcRawOrTagged 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.38
Specifies whether the VLAN tag of the SVC entry is attached or stripped.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER raw(1), tagged(2), rawTagNotConfiged(3)  

hwSvcInterworkingType 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.39
Specifies the interworking type of the SVC entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ipInterWorking(1), ipLayer2(2), ipUnknown(3)  

hwSvcCir 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.40
Specifies the committed information rate, based on the SVC entry.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwSvcPir 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.41
Specifies the peak information rate, based on the SVC entry.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwSvcQosProfile 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.42
Specifies the QoS profile's name, based on the SVC entry.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..63)  

hwSvcRowStatus 1.3.6.1.4.1.2011.5.25.119.4.1.3.1.1.51
RowStatus for this Table. Restriction: The row must be created by 'createAndGo' handle only. Handle 'createAndWait' is forbidden. Not support modifying configuration.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwSvcTnlTable 1.3.6.1.4.1.2011.5.25.119.4.1.3.2
This table is used to search the tunnel index of a SVC.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWSvcTnlEntry

hwSvcTnlEntry 1.3.6.1.4.1.2011.5.25.119.4.1.3.2.1
Provides the information of a SVC tunnel entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWSvcTnlEntry  

hwSvcTnlIndex 1.3.6.1.4.1.2011.5.25.119.4.1.3.2.1.1
This object indicates the tunnel index of the SVC.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

hwSvcTnlType 1.3.6.1.4.1.2011.5.25.119.4.1.3.2.1.2
This object indicates the tunnel type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER lsp(1), gre(2), ipsec(3), crLsp(4)  

hwSvcTnlForBfdIndex 1.3.6.1.4.1.2011.5.25.119.4.1.3.2.1.3
This object indicates the index of LSP for BFD. Currently, can't support.Return the default value is '0'.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwSvcStatisticsTable 1.3.6.1.4.1.2011.5.25.119.4.1.3.3
This table contains the L2vpn's SVC packets statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWSvcStatisticsEntry

hwSvcStatisticsEntry 1.3.6.1.4.1.2011.5.25.119.4.1.3.3.1
Provides the information of the L2VPN's SVC packets Statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWSvcStatisticsEntry  

hwSvcStatisticsRcvPkts 1.3.6.1.4.1.2011.5.25.119.4.1.3.3.1.1
The total number of packets received on this SVC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwSvcStatisticsRcvBytes 1.3.6.1.4.1.2011.5.25.119.4.1.3.3.1.2
The total number of bytes received on this SVC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwSvcStatisticsSndPkts 1.3.6.1.4.1.2011.5.25.119.4.1.3.3.1.3
The total number of packets sent on this SVC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwSvcStatisticsSndBytes 1.3.6.1.4.1.2011.5.25.119.4.1.3.3.1.4
The total number of bytes sent on the SVC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

hwSvcSwitchNotifEnable 1.3.6.1.4.1.2011.5.25.119.4.1.3.4
If this object is set to enable(1), then it enables the emission of hwSvcSwitchWtoP and hwSvcSwitchPtoW notifications; otherwise these notifications are not emitted.Currently, can't support. The default value is disable (2).
Status: current Access: read-write
OBJECT-TYPE    
  HWEnableValue  

hwSvcUpDownNotifEnable 1.3.6.1.4.1.2011.5.25.119.4.1.3.5
This object indicates the enable sign of PW VC state change notification. The default value is disable (2).
Status: current Access: read-write
OBJECT-TYPE    
  HWEnableValue  

hwSvcDeletedNotifEnable 1.3.6.1.4.1.2011.5.25.119.4.1.3.6
This object indicates the enable sign of PW VC deletion notification. The default value is disable (2).
Status: current Access: read-write
OBJECT-TYPE    
  HWEnableValue  

hwSvcStateChangeReason 1.3.6.1.4.1.2011.5.25.119.4.1.3.7
This object indicates the reason of PE VC state change.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  HWL2VpnStateChangeReason  

hwL2vpnSvcMIBTraps 1.3.6.1.4.1.2011.5.25.119.4.1.4
OBJECT IDENTIFIER    

hwSvcSwitchWtoP 1.3.6.1.4.1.2011.5.25.119.4.1.4.1
This notification is generated when switch from working PW to protect PW happens.Currently, can't support.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

hwSvcSwitchPtoW 1.3.6.1.4.1.2011.5.25.119.4.1.4.2
This notification is generated when switch from protect PW to working PW happens.Currently, can't support.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

hwSvcDown 1.3.6.1.4.1.2011.5.25.119.4.1.4.3
This notification indicates the SVC's state changes to down.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

hwSvcUp 1.3.6.1.4.1.2011.5.25.119.4.1.4.4
This notification indicates the SVC's state changes to up.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

hwSvcDeleted 1.3.6.1.4.1.2011.5.25.119.4.1.4.5
This notification indicates the SVC is deleted.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

hwPWTemplateTable 1.3.6.1.4.1.2011.5.25.119.4.1.5
This table specifies information for configuring and status monitoring to PW tempalte.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWPWTemplateEntry

hwPWTemplateEntry 1.3.6.1.4.1.2011.5.25.119.4.1.5.1
A row in this table represents a pseudo wire (PW) template. It is indexed by hwPWCmdTemplateIndex, which uniquely identifying a singular tempalte.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWPWTemplateEntry  

hwPWTemplateName 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.1
The name of the PW template. Set by the operator to indicate the protocol responsible for establishing this PW. The value 'static' is used in all cases where no maintenance protocol (PW signaling) is used to set-up the PW, i.e. require configuration of entries in the PW tables including PW labels, etc. The value 'ldp' is used in case of signaling with the PWid FEC element with LDP signaling. The value 'rsvp' indicate the use of rsvp control protocol.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING Size(0..19)  

hwPWTemplatePeerAddrType 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.2
Denotes the address type of the peer node. It should be set to 'unknown' if PE/PW maintenance protocol is not used and the address is unknown. Currently, support 'ipv4' only.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

hwPWTemplatePeerAddr 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.3
This object contain the value of the peer node address of the PW/PE maintenance protocol entity.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hwPWTemplateCtrlword 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.4
Indicates the control word capability of the switch PW.
Status: current Access: read-create
OBJECT-TYPE    
  HWEnableValue  

hwPWTemplateVCCV 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.5
Indicates the optional VCCV capabilities of the PW template. According to whether the control word is enabled, the value can be ccCw(0)|ccAlert(1)|ccTtl(6)|cvLspping(4)|cvBfd(5) or ccAlert(1)|ccTtl(6)|cvLspping(4)|cvBfd(5). The default value is ccAlert(1)|ccTtl(6)|cvLspping(4)|cvBfd(5).
Status: current Access: read-create
OBJECT-TYPE    
  BITS ccCw(0), ccAlert(1), ccLabel(2), cvIcmpping(3), cvLspping(4), cvBfd(5), ccTtl(6)  

hwPWTemplateFrag 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.6
Indicates whether or not fragmentaion is supported.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

hwPWTemplateBandwidth 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.7
Indicates the bandwitdh when signaling protocol is rsvp. Currently, can't support.'0' is the default value.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..32000000  

hwPWTemplateTnlPolicyName 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.8
Indicates the tunnel policy name used.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..39)  

hwPWTemplateQoSBehaviorIndex 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.9
Indicates the traffic behavior Index when QOS is implemented.Currently, can't support.'0' is the default value.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwPWTemplateExplicitPathName 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.10
Indicates the explicit path name set by the operator.Currently, can't support.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..31)  

hwPWTemplateBFDDetectMultiplier 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.11
The multiple of detection time.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 3..50  

hwPWTemplateBFDMinReceiveInterval 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.12
The interval of bfd messages to be received.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 3..1000  

hwPWTemplateBFDMinTransmitInterval 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.13
The interval of bfd messages to be sent.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 3..1000  

hwPWTemplateDynamicBFDDetect 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.14
This value indicates the capacitability to support dynamic BFD detect.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

hwPWTemplateMaxAtmCells 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.15
Specifies the MaxAtmCells.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..28  

hwPWTemplateAtmPackOvertime 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.16
Specifies the AtmPackOvertime.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 100..50000  

hwPWTemplatePwJitterBufferDepth 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.17
Specifies the PwJitterBufferDepth.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..64  

hwPWTemplatePwTdmEncapsulationNum 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.18
Specifies the PwTdmEncapsulationNum.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..40  

hwPWTemplatePwIdleCode 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.19
Specifies the PwIdleCode.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255 | 65535  

hwPWTemplatePwRtpHeader 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.20
Specifies the PwRtpHeader.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWTemplatePwCCSeqEnable 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.21
Specifies the CC Sequence is enable or not.
Status: current Access: read-create
OBJECT-TYPE    
  HWEnableValue  

hwPWTemplateCir 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.22
Specifies the committed information rate, based on the PW template entry.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWTemplatePir 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.23
Specifies the peak information rate, based on the PW template entry.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwPWTemplateQosProfile 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.24
Specifies the QoS profile's name, based on the PW template entry.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..63)  

hwPWTemplateFlowLabel 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.25
The value of this object identifies whether the PW FlowLabel is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  EnabledStatus  

hwPWTemplateRowStatus 1.3.6.1.4.1.2011.5.25.119.4.1.5.1.51
RowStatus for this Table. Restriction: The row must be created by 'createAndGo' handle only. Handle 'createAndWait' is forbidden.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwPWTemplateMIBTraps 1.3.6.1.4.1.2011.5.25.119.4.1.6
OBJECT IDENTIFIER    

hwPWTemplateCannotDeleted 1.3.6.1.4.1.2011.5.25.119.4.1.6.1
This notification indicates the PWTemplate cannot be deleted.
Status: current Access: read-create
NOTIFICATION-TYPE    

hwPWTableObjects 1.3.6.1.4.1.2011.5.25.119.4.1.7
OBJECT IDENTIFIER    

hwPWTable 1.3.6.1.4.1.2011.5.25.119.4.1.7.1
This table indicates a PW, that is Static PW or LDP PW
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HWPWEntry

hwPWEntry 1.3.6.1.4.1.2011.5.25.119.4.1.7.1.1
Provides the information of a VC key entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWPWEntry  

hwPWId 1.3.6.1.4.1.2011.5.25.119.4.1.7.1.1.1
Index for the conceptual row identifying a PW within this PW Emulation table.Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element'.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

hwPWType 1.3.6.1.4.1.2011.5.25.119.4.1.7.1.1.2
Index for the conceptual row identifying a PW within this PW Emulation table.This value indicate the service to be carried over this PW.
Status: current Access: not-accessible
OBJECT-TYPE    
  HWL2VpnVcEncapsType  

hwPWPeerIp 1.3.6.1.4.1.2011.5.25.119.4.1.7.1.1.3
This object contain the value of the peer node address of the PW/PE maintenance protocol entity. This object SHOULD contain a value of all zeroes if not applicable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

hwPWInterfaceIndex 1.3.6.1.4.1.2011.5.25.119.4.1.7.1.1.4
Index of the interface (or the virtual interface) associated with the PW.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

hwPwe3MIBConformance 1.3.6.1.4.1.2011.5.25.119.4.3
OBJECT IDENTIFIER    

hwPwe3MIBCompliances 1.3.6.1.4.1.2011.5.25.119.4.3.1
OBJECT IDENTIFIER    

hwPwe3MIBCompliance 1.3.6.1.4.1.2011.5.25.119.4.3.1.1
The compliance statement for systems supporting the HUAWEI-PWE3-MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

hwPwe3MIBGroups 1.3.6.1.4.1.2011.5.25.119.4.3.2
OBJECT IDENTIFIER    

hwPWVcGroup 1.3.6.1.4.1.2011.5.25.119.4.3.2.1
The Pwe3's VC group.
Status: current Access: read-only
OBJECT-GROUP    

hwPWVcTnlGroup 1.3.6.1.4.1.2011.5.25.119.4.3.2.2
The PWE3's VC Tunnel group.
Status: current Access: read-only
OBJECT-GROUP    

hwPWVcStatisticsGroup 1.3.6.1.4.1.2011.5.25.119.4.3.2.3
The PWE3's VC Statistics group.
Status: current Access: read-only
OBJECT-GROUP    

hwPWRemoteVcGroup 1.3.6.1.4.1.2011.5.25.119.4.3.2.4
The PWE3's Remote VC group.
Status: current Access: read-only
OBJECT-GROUP    

hwPWTemplateGroup 1.3.6.1.4.1.2011.5.25.119.4.3.2.5
The PWE3's Template group.
Status: current Access: read-only
OBJECT-GROUP    

hwPWNotificationControlGroup 1.3.6.1.4.1.2011.5.25.119.4.3.2.6
The PWE3's Notification Control group.
Status: current Access: read-only
OBJECT-GROUP    

hwPWVcStateChangeReasonGroup 1.3.6.1.4.1.2011.5.25.119.4.3.2.7
The PWE3's Vc State Reason group.
Status: current Access: read-only
OBJECT-GROUP    

hwPWVcNotificationGroup 1.3.6.1.4.1.2011.5.25.119.4.3.2.8
The PWE3's VC Notification group.
Status: current Access: read-only
NOTIFICATION-GROUP    

hwLdpPWStateChangeReasonGroup 1.3.6.1.4.1.2011.5.25.119.4.3.2.9
The LDP PW VC State Reason group.
Status: current Access: read-only
OBJECT-GROUP    

hwPWVcTDMPerfCurrentGroup 1.3.6.1.4.1.2011.5.25.119.4.3.2.10
The PWE3's VC TDM performance information group.
Status: current Access: read-only
OBJECT-GROUP    

hwL2vpnSvcMIBGroups 1.3.6.1.4.1.2011.5.25.119.4.3.3
OBJECT IDENTIFIER    

hwSvcGroup 1.3.6.1.4.1.2011.5.25.119.4.3.3.1
The L2vpn's SVC group.
Status: current Access: read-only
OBJECT-GROUP    

hwSvcTnlGroup 1.3.6.1.4.1.2011.5.25.119.4.3.3.2
The L2vpn's SVC Tunnel group.
Status: current Access: read-only
OBJECT-GROUP    

hwSvcStatisticsGroup 1.3.6.1.4.1.2011.5.25.119.4.3.3.3
The L2vpn's SVC Statistics group.
Status: current Access: read-only
OBJECT-GROUP    

hwSvcNotificationControlGroup 1.3.6.1.4.1.2011.5.25.119.4.3.3.4
The L2vpn SVC's Notification Control group.
Status: current Access: read-only
OBJECT-GROUP    

hwSvcStateChangeReasonGroup 1.3.6.1.4.1.2011.5.25.119.4.3.3.5
The L2vpn's SVc State Reason group.
Status: current Access: read-only
OBJECT-GROUP    

hwSvcNotificationGroup 1.3.6.1.4.1.2011.5.25.119.4.3.3.6
The L2vpn's SVC Notification group.
Status: current Access: read-only
NOTIFICATION-GROUP    

hwL2vpnPWTableMIBGroups 1.3.6.1.4.1.2011.5.25.119.4.3.4
OBJECT IDENTIFIER    

hwPWTableGroup 1.3.6.1.4.1.2011.5.25.119.4.3.4.1
The PW Table Group.
Status: current Access: read-only
OBJECT-GROUP    

hwPWTemplateMIBGroups 1.3.6.1.4.1.2011.5.25.119.4.3.5
OBJECT IDENTIFIER    

hwPWTemplateNotificationGroup 1.3.6.1.4.1.2011.5.25.119.4.3.5.1
The L2vpn's PW Template Notification group.
Status: current Access: read-only
NOTIFICATION-GROUP