IBM-TS4500-MIBv2

File: IBM-TS4500-MIBv2.mib (105598 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
enterprises Integer32 DisplayString
MODULE-COMPLIANCE OBJECT-GROUP NOTIFICATION-GROUP

Defined Values

ibm3584 1.3.6.1.4.1.2.6.182
Initial revision of this module.
MODULE-IDENTITY    

ibm 1.3.6.1.4.1.2
OBJECT IDENTIFIER    

ibmProd 1.3.6.1.4.1.2.6
OBJECT IDENTIFIER    

ibm3584MIB 1.3.6.1.4.1.2.6.182.1
OBJECT IDENTIFIER    

ibm3584MIBTraps 1.3.6.1.4.1.2.6.182.1.0
OBJECT IDENTIFIER    

ibm3584MIBAdmin 1.3.6.1.4.1.2.6.182.1.1
OBJECT IDENTIFIER    

ibm3584MIBObjects 1.3.6.1.4.1.2.6.182.1.2
OBJECT IDENTIFIER    

ibm3584MIBConformance 1.3.6.1.4.1.2.6.182.1.3
OBJECT IDENTIFIER    

ibm3584MIBGroupMTMNLSN 1.3.6.1.4.1.2.6.182.1.2.11
OBJECT IDENTIFIER    

ibm3584MIBGroupSKASCASCQ 1.3.6.1.4.1.2.6.182.1.2.21
OBJECT IDENTIFIER    

ibm3584MIBGroupErrorCode 1.3.6.1.4.1.2.6.182.1.2.31
OBJECT IDENTIFIER    

ibm3584MIBGroupURC 1.3.6.1.4.1.2.6.182.1.2.41
OBJECT IDENTIFIER    

ibm3584MIBGroupTD 1.3.6.1.4.1.2.6.182.1.2.51
OBJECT IDENTIFIER    

ibm3584MIBGroupVOLSER 1.3.6.1.4.1.2.6.182.1.2.61
OBJECT IDENTIFIER    

ibm3584MIBGroupLL 1.3.6.1.4.1.2.6.182.1.2.71
OBJECT IDENTIFIER    

ibm3584MIBGroupWWNN 1.3.6.1.4.1.2.6.182.1.2.81
OBJECT IDENTIFIER    

ibm3584MIBGroupDrvSN 1.3.6.1.4.1.2.6.182.1.2.91
OBJECT IDENTIFIER    

ibm3584MIBSeverity 1.3.6.1.4.1.2.6.182.1.2.101
OBJECT IDENTIFIER    

ibm3584MIBUserID 1.3.6.1.4.1.2.6.182.1.2.111
OBJECT IDENTIFIER    

ibm3584MIBLocation 1.3.6.1.4.1.2.6.182.1.2.121
OBJECT IDENTIFIER    

ibm3584MIBObjectsMTMNLSN 1.3.6.1.4.1.2.6.182.1.2.11.1
This is the machine type associated with the trap.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

ibm3584MIBObjectsSKASCASCQ 1.3.6.1.4.1.2.6.182.1.2.21.1
This is the sense key associated with the trap.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

ibm3584MIBObjectsErrorCode 1.3.6.1.4.1.2.6.182.1.2.31.1
This is the hardware error code associated with the trap.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..5)  

ibm3584MIBObjectsURC 1.3.6.1.4.1.2.6.182.1.2.41.1
This is the URC associated with the trap.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..4)  

ibm3584MIBObjectsTD 1.3.6.1.4.1.2.6.182.1.2.51.1
This is the text description of the trap.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..255)  

ibm3584MIBObjectsVOLSER 1.3.6.1.4.1.2.6.182.1.2.61.1
This is the Volume Serial number on the cartridge.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

ibm3584MIBObjectsLL 1.3.6.1.4.1.2.6.182.1.2.71.1
This is the Logical Library that is having a problem within the physical library.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

ibm3584MIBObjectsWWNN 1.3.6.1.4.1.2.6.182.1.2.81.1
The World Wide Node Name of the Drive that is having problems.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

ibm3584MIBObjectsDrvSN 1.3.6.1.4.1.2.6.182.1.2.91.1
The Serial Number of the Drive that is having problems.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..12)  

ibm3584MIBObjectsSeverity 1.3.6.1.4.1.2.6.182.1.2.101.1
Indicates the percieved severity of the problem
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER error(0), warning(1), information(4)  

ibm3584MIBObjectsUserID 1.3.6.1.4.1.2.6.182.1.2.111.1
This is the User ID associated with a request via external UI.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..20)  

ibm3584MIBObjectsLocation 1.3.6.1.4.1.2.6.182.1.2.121.1
This is the location of the device that generated the trap.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..50)  

ibm3584Trap001 1.3.6.1.4.1.2.6.182.1.0.1
Trap for library TapeAlert 001. Flag: Library hardware A Type: C Cause: The library has trouble communicating with the drive. Required host message: The library has trouble communicating with the drive. 1. Restart the operation. 2. If the problem persists, call your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap002 1.3.6.1.4.1.2.6.182.1.0.2
Trap for library TapeAlert 002. Flag: Library hardware B. Type: W Cause: The library has a hardware failure. Required host message: The library has a hardware failure. 1. Restart the operation. 2. If the problem persists, call your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap004 1.3.6.1.4.1.2.6.182.1.0.4
Trap for library TapeAlert 004. Flag: Library hardware D. Type: C Cause: The library has a hardware fault that is not mechanically. Required host message: The library has a hardware fault that is not mechanically related. 1. Restart the operation. 2. If the problem persists, call your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap007 1.3.6.1.4.1.2.6.182.1.0.7
Trap for library TapeAlert 007. Flag: Predictive failure. Type: W Cause: The library detected that a hardware component is degraded but stil operational. Required host message: A hardware The library detected that a hardware component is degraded but stil operational. Call your IBM service representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap016 1.3.6.1.4.1.2.6.182.1.0.16
Trap for library TapeAlert 016. Flag: Library door. Type: C Cause: A library door is open and prevents the library from functioning. Required host message: A library door is open and prevents the library from functioning. 1. Close the library door. 2. If the problem persists, call your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap017 1.3.6.1.4.1.2.6.182.1.0.17
Trap for library TapeAlert 017. Flag: Library I/O station. Type: C Cause: A problem with an I/O station exists. Required host message: A problem with an I/O station exists. 1. Ensure that there is no obstruction in the I/O station. 2. Restart the operation. 3. If the problem persists, call your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap020 1.3.6.1.4.1.2.6.182.1.0.20
Trap for library TapeAlert 020. Flag: Library security mode. Type: I Cause: Library security mode has changed. Required host message: The security mode of the library has been changed. Either the library has been put into secure mode or the library has exited secure mode. This is for informational purposes only. No action is required.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap021 1.3.6.1.4.1.2.6.182.1.0.21
Trap for library TapeAlert 021. Flag: Library offline. Type: I Cause: Library manually turned offline. Required host message: The library has been manually turned offline and is unavailable for use.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap022 1.3.6.1.4.1.2.6.182.1.0.22
Trap for library TapeAlert 022. Flag: Library drive offline. Type: I Cause: Library turned internal drive offline. Required host message: A drive inside the library has been taken offline. This is for informational purposes only. No action is required.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap024 1.3.6.1.4.1.2.6.182.1.0.24
Trap for library TapeAlert 024. Flag: Library inventory. Type: C Cause: An inventory of the media was inconsistent. Required host message: An inventory of the media was inconsistent. 1. Run a library inventory to correct the inconsistency. 2. Restart operation. 3. If the problem persists, call your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap028 1.3.6.1.4.1.2.6.182.1.0.28
Trap for library TapeAlert 028. Flag: Power supply. Type: W Cause: A redundant power supply failure exists inside the library subsystem. Required host message: A redundant power supply failure exists inside the library subsystem. Call your IBM service representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap030 1.3.6.1.4.1.2.6.182.1.0.30
Trap for library TapeAlert 030. Flag: Shuttle mechanism failure. Type: C Cause: A failure has occurred in the shuttle mechanism while attempting to transfer a cartridge between two library strings. Required host message: A failure has occurred in the shuttle mechanism while attempting to transfer a cartridge between two library strings. 1. Restart the operation. 2. If the problem persists, call your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap031 1.3.6.1.4.1.2.6.182.1.0.31
Trap for library TapeAlert 031. Flag: Cartridge in pass-through mechanism. Type: C Cause: Cartridge left in the pass-through mechanism between two library modules. Required host message: A cartridge has been left in the library pass-through mechanism from a previous hardware fault. Check the library users guide for instructions on clearing this fault.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap032 1.3.6.1.4.1.2.6.182.1.0.32
Trap for library TapeAlert 032. Flag: Unreadable bar code labels. Type: I Cause: During an inventory or scan, the library was unable to read a bar code label on a cartridge. Required host message: During an inventory or scan, the library was unable to read a bar code label on a cartridge. 1. Check for damaged, misaligned, or peeling barcode labels on the cartridge. 2. If you find a damaged, misaligned or peeling bar code label, replace it with a new barcode label. To request a new barcode label, call you IBM Service Representative. 2. If no problem is found, call your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap201 1.3.6.1.4.1.2.6.182.1.0.201
Trap for drive TapeAlert 001. Flag: Read warning. Type: W Cause: The drive is having problems reading data. Required host message: The tape drive is having problems reading data. No data has been lost, but there has been a reduction in the performance of the tape. Isolate the fault between the drive and the tape by doing the following: 1) Use a known good cartidge in the suspect drive. If the drive fails, contact your IBM Service Representative. 2) Use the suspect tape cartrige in a known good drive. If the test fails, discard the cartridge.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap202 1.3.6.1.4.1.2.6.182.1.0.202
Trap for drive TapeAlert 002. Flag: Write warning. Type: W Cause: The drive is having problems writing data. Required host message: The tape drive is having problems writing data. No data has been lost, but there has been a reduction in the performance of the tape. Isolate the fault between the drive and the tape by doing the following: 1) Use a known good cartidge in the suspect drive. If the drive fails, contact your IBM Service Representative. 2) Use the suspect tape cartrige in a known good drive. If the test fails, discard the cartridge.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap203 1.3.6.1.4.1.2.6.182.1.0.203
Trap for drive TapeAlert 003. Flag: Hard error. Type: W Cause: The drive had an unrecoverable read, write, or positioning error. Required host message: The drive had an unrecoverable read, write, or positioning error. Determine if flags 4, 5, or 6, exist; follow the actions there.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap204 1.3.6.1.4.1.2.6.182.1.0.204
Trap for drive TapeAlert 004. Flag: Media. Type: C Cause: The drive had an unrecoverable read, write, or positioning error that is due to faulty media. Required host message: The drive had an unrecoverable read, write, or positioning error that is due to faulty media. Replace the tape cartridge.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap205 1.3.6.1.4.1.2.6.182.1.0.205
Trap for drive TapeAlert 005. Flag: Read failure. Type: C Cause: The drive can not determine if an unrecoverable read failure is due to faulty media or drive hardware. Required host message: The drive can not determine if an unrecoverable read failure is due to faulty media or drive hardware. 1) Discard the tape cartridge. 2) If the problem persists, contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap206 1.3.6.1.4.1.2.6.182.1.0.206
Trap for drive TapeAlert 006. Flag: Write failure. Type: C Cause: The drive can not determine if an unrecoverable write failure is due to faulty media or drive hardware. Required host message: The drive can not determine if an unrecoverable write failure is due to faulty media or drive hardware. 1) Discard the tape cartridge. 2) If the problem persists, contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap207 1.3.6.1.4.1.2.6.182.1.0.207
Trap for drive TapeAlert 007. Flag: Media life. Type: W Cause: The media has reached its end of life. Required host message: The media has reached its end of life. 1. Copy the data to another tape cartridge. 2. Discard the old tape cartridge.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap208 1.3.6.1.4.1.2.6.182.1.0.208
Trap for drive TapeAlert 008. Flag: Not data grade. Type: W Cause: The cartridge is not data-grade. Any data that you write to the tape is at risk. Required host message: The cartridge is not data-grade. Any data that you write to the tape is at risk. Replace the tape with a data-grade tape. 1) Discard the tape cartridge. 2) If the problem persists, contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap209 1.3.6.1.4.1.2.6.182.1.0.209
Trap for drive TapeAlert 009. Flag: Write protect. Type: C Cause: The drive has detected a write command for a write protected tape cartridge. Required host message: The drive has detected a write command for a write protected tape cartridge. 1) Set the write protect switch on the cartridge to OFF. 2) Enusre that the tape cartridge is not logically protected. 3) If the problem persists, contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap210 1.3.6.1.4.1.2.6.182.1.0.210
Trap for drive TapeAlert 010. Flag: No removal. Type: I Cause: The tape drive received an UNLOAD command after the server prevented the tape cartridge from being removed. Required host message: The tape drive received an UNLOAD command after the server prevented the tape cartridge from being removed. 1) If the error is an operator error, no action is required. 2) If the error is a customer software error, see the documentation for your server's operating system.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap211 1.3.6.1.4.1.2.6.182.1.0.211
Trap for drive TapeAlert 011. Flag: Cleaning media. Type: I Cause: Cleaning tape loaded into drive. Required host message: A cleaning tape has been loaded into drive. No action is required.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap212 1.3.6.1.4.1.2.6.182.1.0.212
Trap for drive TapeAlert 012. Flag: Unsupported format. Type: I Cause: The drive has detected a tape cartridge with an unsupported tape format. Required host message: The drive has detected a tape cartridge with an unsupported tape format. 1) Remove the invalid tape cartridge. 2) If the problem persists, contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap213 1.3.6.1.4.1.2.6.182.1.0.213
Trap for drive TapeAlert 013. Flag: Recoverable snapped tape. Type: C Cause: Tape snapped/cut in the drive where media can be ejected. Required host message: The tape has split apart. Do not attempt to extract the old tape cartridge. Call your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap214 1.3.6.1.4.1.2.6.182.1.0.214
Trap for drive TapeAlert 014. Flag: Unrecoverable snapped tape. Type: C Cause: Tape snapped/cut in the drive where media cannot be ejected. Required host message: The operation has failed because the tape in the drive has snapped: 1. Do not attempt to extract the tape cartridge. 2. Call the tape drive supplier helpline.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap215 1.3.6.1.4.1.2.6.182.1.0.215
Trap for drive TapeAlert 015. Flag: Memory chip in cartridge failure. Type: W Cause: Memory chip failed in cartridge. Required host message: The memory in the tape cartridge has failed, which reduces performance. 1) Replace the tape cartridge. 2) If this error occurs on multiple cartridges, see Error Code 6 located in the list of drive error codes in the 3584 Maintenance Information Guide.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap216 1.3.6.1.4.1.2.6.182.1.0.216
Trap for drive TapeAlert 016. Flag: Forced eject. Type: C Cause: Manual or forced eject while drive actively writing or reading. Required host message: The operation has failed because the tape cartridge was manually ejected while the tape drive was actively writing or reading. No action required.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap217 1.3.6.1.4.1.2.6.182.1.0.217
Trap for drive TapeAlert 017. Flag: Read only format. Type: W Cause: Media loaded that is read-only format. Required host message: You have loaded a cartridge of a type that is read-only in this drive. The cartridge will appear as write-protected. No action required.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap218 1.3.6.1.4.1.2.6.182.1.0.218
Trap for drive TapeAlert 018. Flag: Tape directory corrupted on load. Type: W Cause: Tape drive powered down with tape loaded, or permanent error prevented the tape directory being updated. Required host message: The drive detected that the tape directory in the cartridge memory has been corrupted. Re-read all data from the tape to rebuild the tape directory.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap220 1.3.6.1.4.1.2.6.182.1.0.220
Trap for drive TapeAlert 020. Flag: Clean now. Type: C Cause: The drive thinks it has a head clog, or needs cleaning. Required host message: The tape drive needs cleaning: 1. If the operation has stopped, eject the tape and clean the drive. 2. If the operation has not stopped, wait for it to finish and then clean the drive.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap221 1.3.6.1.4.1.2.6.182.1.0.221
Trap for drive TapeAlert 021. Flag: Clean periodic. Type: W Cause: The drive is ready for a periodic clean Required host message: The tape drive is due for routine cleaning: 1. Wait for the current operation to finish. 2. Clean the drive as soon as possible.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap222 1.3.6.1.4.1.2.6.182.1.0.222
Trap for drive TapeAlert 022. Flag: Expired cleaning media. Type: C Cause: The cleaning tape has expired. Required host message: The last cleaning cartridge used in the tape drive has worn out: 1. Discard the worn out cleaning cartridge.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap223 1.3.6.1.4.1.2.6.182.1.0.223
Trap for drive TapeAlert 023. Flag: Invalid cleaning tape. Type: C Cause: Invalid cleaning tape type used. Required host message: The last cleaning cartridge used in the tape drive was an invalid type: 1. Do not use this cleaning cartridge in this drive. 2. Wait for the current operation to finish. 3. Then use a valid cleaning cartridge.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap225 1.3.6.1.4.1.2.6.182.1.0.225
Trap for drive TapeAlert 025. Flag: Dual-port interface error. Type: W Cause: Failure of one interface port in a dual-port configuration, eg Fibrechannel. Required host message: A redundant interface port on the tape drive has failed. Contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap226 1.3.6.1.4.1.2.6.182.1.0.226
Trap for drive TapeAlert 026. Flag: Cooling fan failure. Type: W Cause: Fan failure inside tape drive mechanism or tape drive enclosure. Required host message: A tape drive cooling fan has failed. Contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap227 1.3.6.1.4.1.2.6.182.1.0.227
Trap for drive TapeAlert 027. Flag: Power supply. Type: W Cause: Redundant PSU failure inside the tape drive enclosure or rack subsystem. Required host message: A redundant power supply has failed inside the tape drive enclosure. Contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap230 1.3.6.1.4.1.2.6.182.1.0.230
Trap for drive TapeAlert 030. Flag: Hardware A. Type: C Cause: The drive has a hardware fault that requires reset to recover. Required host message: A hardware failure has occurred that requires a tape drive reset to recover. 1) Reset the drive. 2) If the problem persists, contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap231 1.3.6.1.4.1.2.6.182.1.0.231
Trap for drive TapeAlert 031. Flag: Hardware B. Type: C Cause: The drive has a hardware fault which is not read/write related or requires a power cycle to recover. Required host message: The tape drive failed it's internal Power-On Self Test. Contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap232 1.3.6.1.4.1.2.6.182.1.0.232
Trap for drive TapeAlert 032. Flag: Interface. Type: W Cause: The drive has identified an interfacing fault. Required host message: The tape drive has detected a problem with the Fibre Channel Interface. Contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap233 1.3.6.1.4.1.2.6.182.1.0.233
Trap for drive TapeAlert 033. Flag: Eject media. Type: C Cause: A failure has occurred that requires you to unload the cartridge from the drive. Required host message: A failure has occurred that requires you to unload the cartridge from the drive. 1) Unload the tape cartridge and try different media. 2) If the problem persists, contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap234 1.3.6.1.4.1.2.6.182.1.0.234
Trap for drive TapeAlert 034. Flag: Download failed. Type: W Cause: Firmware download failed. Required host message: The firmware download has failed. Contact you IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap235 1.3.6.1.4.1.2.6.182.1.0.235
Trap for drive TapeAlert 035. Flag: Drive humidity. Type: W Cause: Drive humidity limits exceeded. Required host message: Environmental conditions inside the tape drive are outside the specified humidity range.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap236 1.3.6.1.4.1.2.6.182.1.0.236
Trap for drive TapeAlert 036. Flag: Drive temperature. Type: W Cause: Drive temperature limits exceeded. Required host message: The drive detected the temperature is exceeding the recommended temperature of the library. Contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap237 1.3.6.1.4.1.2.6.182.1.0.237
Trap for drive TapeAlert 037. Flag: Drive voltage. Type: W Cause: Drive voltage limits exceeded. Required host message: The drive detected externally supplied voltages are approaching or outside the specified voltage limits. Contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap249 1.3.6.1.4.1.2.6.182.1.0.249
Trap for drive TapeAlert 049. Flag: Media. Type: C Cause: The beginning of partition 0 for cartridge was written to unexpectedly. Required host message: The beginning of partition 0 for cartridge was written to unexpectedly.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap252 1.3.6.1.4.1.2.6.182.1.0.252
Trap for drive TapeAlert 052. Flag: Tape system area write failure. Type: C Cause: Write errors while writing the system log on unload. Required host message: The tape cartridge that was previously unloaded could not write it's system area successfully. Copy the data to another tape cartridge, then discard the old cartridge.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap253 1.3.6.1.4.1.2.6.182.1.0.253
Trap for drive TapeAlert 053. Flag: Tape system area read failure. Type: C Cause: Read errors while reading the system area on load. Required host message: The tape system area could not be read successfully at load time. Copy the data to another tape cartridge, then discard the old cartridge.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap254 1.3.6.1.4.1.2.6.182.1.0.254
Trap for LTO drive TapeAlert 054. Flag: No start of data. Type: C Cause: Tape damaged, bulk erased, or incorrect format. Required host message: The start of data could not be found on the tape: 1. Check you are using the correct format tape. 2. If correct, discard the tape cartridge and try another one. 3. If the problem persists, contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap255 1.3.6.1.4.1.2.6.182.1.0.255
Trap for drive TapeAlert 055. Flag: Load Failure. Type: C Cause: Loading failure Required host message: The operation has failed because the media cannot be loaded and threaded. 1. Discard the tape cartridge and try another one. 2. If the problem persists, contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap256 1.3.6.1.4.1.2.6.182.1.0.256
Trap for drive TapeAlert 056. Flag: Unrecoverable unload failure. Type: C The operation has failed because the medium cannot be unloaded: 1. Do not attempt to extract the tape cartridge. 2. Contact your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap257 1.3.6.1.4.1.2.6.182.1.0.257
Trap for drive TapeAlert 057. Flag: Automation interface failure. Type: C The tape drive has a problem with the automation interface: 1. Check the power to the automation system. 2. Check the cables and cable connections. 3. If the problem persists, contract your IBM Service Representative.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap259 1.3.6.1.4.1.2.6.182.1.0.259
Trap for drive TapeAlert 059. Flag: WORM Medium - Integrity Check Failed Type: W The tape drive has detected an inconsistency during the WORM medium integrity checks. 1) Copy the data to another WORM tape cartridge. 2) Discard the faulty WORM tape cartridge.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap260 1.3.6.1.4.1.2.6.182.1.0.260
Trap for drive TapeAlert 060. Flag: WORM Medium - Overwrite Attempted Type: W An attempt had been made to overwrite user data on a WORM medium: 1. If a WORM medium was used inadvertently, replace it with a normal data medium. 2. If a WORM medium was used intentionally: a) check that the software application is compatible with the WORM medium format you are using. b) check that the medium is bar-coded correctly for WORM.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap401 1.3.6.1.4.1.2.6.182.1.0.401
Trap for non TapeAlert 001. Cause: I/O station full. Required host message: The Import/Export station is full.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap402 1.3.6.1.4.1.2.6.182.1.0.402
Trap for non TapeAlert 002. Cause: All cartridge slots in the associated logical library are occupied. Required host message: The logical library is full.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap403 1.3.6.1.4.1.2.6.182.1.0.403
Trap for non TapeAlert 003. Cause: Library out of LTO cleaning cartridges. Required host message: The library is out of LTO cleaning cartridges.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap405 1.3.6.1.4.1.2.6.182.1.0.405
Trap for non TapeAlert 005. Cause: I/O station door has been open for five minutes. Required host message: The Import/Export station has been open for five minutes.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap406 1.3.6.1.4.1.2.6.182.1.0.406
Trap for non TapeAlert 006. Cause: LTO cleaning cartridge expired. Required host message: An LTO cleaning cartridge has expired.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap407 1.3.6.1.4.1.2.6.182.1.0.407
Trap for non TapeAlert 007. Cause: A shuffle operation failed because there were no open slots in the library. Required host message: A shuffle operation failed because there were no open slots in the library.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap408 1.3.6.1.4.1.2.6.182.1.0.408
Trap for non TapeAlert 008. Cause: Test initiated from operator panel. Required host message: This is a test SNMP trap.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap409 1.3.6.1.4.1.2.6.182.1.0.409
Trap for non TapeAlert 009. Cause: Library out of 3592 Enterprise Tape cleaning cartridges. Required host message: The library is out of Enterprise Tape cleaning cartridges.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap410 1.3.6.1.4.1.2.6.182.1.0.410
Trap for non TapeAlert 010. Cause: 3592 Enterprise Tape cleaning cartridge expired. Required host message: A Enterprise Tape cleaning cartridge has expired.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap415 1.3.6.1.4.1.2.6.182.1.0.415
Trap for non TapeAlert 015. Cause: The library attempted to call home, but was unsuccessful. Required host message: The library attempted to call home, but was unsuccessful.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap416 1.3.6.1.4.1.2.6.182.1.0.416
Trap for non TapeAlert 016. Cause: The associated logical library is nearing full capacity. Required host message: The logical library is almost full.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap419 1.3.6.1.4.1.2.6.182.1.0.419
Trap for non TapeAlert 019. Cause: Unable to reach associated EKM. Required host message: Library is unable to communicate with the associated EKM address.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap420 1.3.6.1.4.1.2.6.182.1.0.420
Trap for non TapeAlert 020. Cause: A cartridge that can not be encrypted has is loaded in a drives that is used to encrypt all cartridges. Required host message: A cartridge that can not be encrypted has been loaded into a drive that is setup for encryption.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap421 1.3.6.1.4.1.2.6.182.1.0.421
Trap for non TapeAlert 021. Cause: A new unassigned cartridge is in the library. Required host message: A new cartridge is in the library and is currently unassigned.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap422 1.3.6.1.4.1.2.6.182.1.0.422
Trap for non TapeAlert 022. Cause: All library doors are closed. The library will inventory and resume operations. Required host message: All library doors have been closed. The library will now inventory and resume operations.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap424 1.3.6.1.4.1.2.6.182.1.0.424
Trap for non TapeAlert 024. Cause: The library was almost out of licensed LTO storage slots. Required host message: The library was almost out of licensed LTO storage slots.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap425 1.3.6.1.4.1.2.6.182.1.0.425
Trap for non TapeAlert 025. Cause: The library was almost out of licensed 3592 storage slots. Required host message: The library was almost out of licensed 3592 storage slots.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap426 1.3.6.1.4.1.2.6.182.1.0.426
Trap for non TapeAlert 026. Cause: The library ran out of licensed 3592 storage slots. Required host message: The library ran out of licensed 3592 storage slots.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap427 1.3.6.1.4.1.2.6.182.1.0.427
Trap for non TapeAlert 027. Cause: The library ran out of licensed LTO storage slots: The library ran out of licensed LTO storage slots.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap428 1.3.6.1.4.1.2.6.182.1.0.428
Trap for non TapeAlert 028. Cause: A fixed home slot was not available. Required host message: A fixed home slot was not available.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap429 1.3.6.1.4.1.2.6.182.1.0.429
Trap for non TapeAlert 029. Cause: An inventory of the library was started. Required host message: An inventory of the library was started.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap430 1.3.6.1.4.1.2.6.182.1.0.430
Trap for non TapeAlert 030. Cause: An inventory of the library ended. Required host message: An inventory of the library ended.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap431 1.3.6.1.4.1.2.6.182.1.0.431
Trap for non TapeAlert 031. Cause: Call home request initiated from the host. Required host message: Call home request initiated from the host.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap432 1.3.6.1.4.1.2.6.182.1.0.432
Trap for non TapeAlert 032. Cause: Test call home sent. Required host message: Test call home sent.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap433 1.3.6.1.4.1.2.6.182.1.0.433
Trap for non TapeAlert 033. Cause: No LTO diagnostic cartridge found in the library. Required host message: No LTO diagnostic cartridge found in the library.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap434 1.3.6.1.4.1.2.6.182.1.0.434
Trap for non TapeAlert 034. Cause: No 3592 diagnostic cartridge found in the library. Required host message: No 3592 diagnostic cartridge found in the library.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap435 1.3.6.1.4.1.2.6.182.1.0.435
Trap for non TapeAlert 035. Cause: The humidity was higher than what is recommended. Required host message: The humidity was higher than what is recommended.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap436 1.3.6.1.4.1.2.6.182.1.0.436
Trap for non TapeAlert 036. Cause: The temperature was higher than what is recommended. Required host message: The temperature was higher than what is recommended.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap440 1.3.6.1.4.1.2.6.182.1.0.440
Trap for non TapeAlert 040. Cause: A user has successfully logged in to the web or operator panel. Required host message: A user has successfully logged into the Web Specialist or Operator Panel.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap441 1.3.6.1.4.1.2.6.182.1.0.441
Trap for non TapeAlert 041. Cause: A user has attempted to log in to the web or operator panel and was unsuccessful. Required host message: A user has attempted to log in to the Web Specialist or Operator Panel and was unsuccessful.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap442 1.3.6.1.4.1.2.6.182.1.0.442
Trap for non TapeAlert 042. Cause: A user has logged out of the web or operator panel. Required host message: A user has logged out of the Web Specialist or Operator Panel.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap443 1.3.6.1.4.1.2.6.182.1.0.443
Trap for non TapeAlert 043. Cause: A library configuration setting has been changed. Required host message: A library configuration setting has been changed via the Op Panel or Web Specialist.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap444 1.3.6.1.4.1.2.6.182.1.0.444
Trap for non TapeAlert 044. Cause: A logical library configuration setting has been changed. Required host message: A logical library configuration setting has been changed.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap445 1.3.6.1.4.1.2.6.182.1.0.445
Trap for non TapeAlert 045. Cause: A tape drive configuration setting has been changed. Required host message: A tape drive configuration setting has been changed.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap446 1.3.6.1.4.1.2.6.182.1.0.446
Trap for non TapeAlert 046. Cause: A cartridge has been modified from an external UI. Required host message: A cartridge has been modified from the Web Specialist or Op Panel.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap447 1.3.6.1.4.1.2.6.182.1.0.447
Trap for non TapeAlert 047. Cause: A library, drive, or shuttle code load has been initiated from an external UI. Required host message: A library, drive, or shuttle code load has been initiated from the Web Specialist, Op Panel, or CE Tool.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap448 1.3.6.1.4.1.2.6.182.1.0.448
Trap for non TapeAlert 048. Cause: An Accessor FRU been prepared/finished. Required host message: An Accessor has been placed in the prepared or finished Accessor service state.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap449 1.3.6.1.4.1.2.6.182.1.0.449
Trap for non TapeAlert 049. Cause: A drive FRU been prepared/finished. Required host message: A drive has been placed in the prepared or finished Drive service state.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap450 1.3.6.1.4.1.2.6.182.1.0.450
Trap for non TapeAlert 050. Cause: A drive Serial number has changed. Required host message: A drive Serial number has changed.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap451 1.3.6.1.4.1.2.6.182.1.0.451
Trap for non TapeAlert 051. Cause: A drive has been power cycled from the web UI. Required host message: A drive has been power cycled via the Web Specialist.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap452 1.3.6.1.4.1.2.6.182.1.0.452
Trap for non TapeAlert 052. Cause: A node card has been reset from the web UI. Required host message: A node card has been reset via the Web Specialist.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap453 1.3.6.1.4.1.2.6.182.1.0.453
Trap for non TapeAlert 053. Cause: The admin password has been changed from the web UI or Op Panel. Required host message: The admin password has been changed from the web UI or Op Panel.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap454 1.3.6.1.4.1.2.6.182.1.0.454
Trap for non TapeAlert 054. Cause: A cartridge has been left in a gripper. Required host message: A cartridge has been left in a gripper.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap455 1.3.6.1.4.1.2.6.182.1.0.455
Trap for non TapeAlert 055. Cause: A library firmware update failed. Required host message: A library firmware update failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap456 1.3.6.1.4.1.2.6.182.1.0.456
Trap for non TapeAlert 056. Cause: A corrupted library firwmware image was downloaded. Required host message: A corrupted library firwmware image was downloaded.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap457 1.3.6.1.4.1.2.6.182.1.0.457
Trap for non TapeAlert 057. Cause: A drive firmware update failed. Required host message: A drive firmware update failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap458 1.3.6.1.4.1.2.6.182.1.0.458
Trap for non TapeAlert 058. Cause: A library firmware update finished. Required host message: A A library firmware update finished.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584Trap459 1.3.6.1.4.1.2.6.182.1.0.459
Trap for non TapeAlert 059. Cause: A A library firmware update finished. Required host message: A A library firmware update finished.
Status: current Access: read-only
NOTIFICATION-TYPE    

ibm3584MIBCompliances 1.3.6.1.4.1.2.6.182.1.3.1
OBJECT IDENTIFIER    

ibm3584MIBGroups 1.3.6.1.4.1.2.6.182.1.3.2
OBJECT IDENTIFIER    

ibm3584MIBCompliance 1.3.6.1.4.1.2.6.182.1.3.1.1
The compliance statement for the SNMP entities that implement this MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

ibm3584MIBNotificationsGroup1 1.3.6.1.4.1.2.6.182.1.3.2.1
Mandatory notification for entities implemented in this MIB.
Status: current Access: read-only
NOTIFICATION-GROUP    

ibm3584MIBObjectsGroup 1.3.6.1.4.1.2.6.182.1.3.2.3
Mandatory objects for entities implemented in this MIB.
Status: current Access: read-only
OBJECT-GROUP