IPS-AUTH-MIB

File: IPS-AUTH-MIB.mib (41980 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
SNMP-FRAMEWORK-MIB IANA-ADDRESS-FAMILY-NUMBERS-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE OBJECT-IDENTITY
Unsigned32 mib-2 TEXTUAL-CONVENTION
RowStatus AutonomousType StorageType
MODULE-COMPLIANCE OBJECT-GROUP SnmpAdminString
AddressFamilyNumbers

Defined Types

IpsAuthAddress  
IP Storage requires the use of address information that uses not only the InetAddress type defined in the INET-ADDRESS-MIB, but also Fibre Channel type defined in the Fibre Channel Management MIB. Although these address types are recognized in the IANA Address Family Numbers MIB, the addressing mechanisms have not been merged into a well-known, common type. This data type, the IpsAuthAddress, performs the merging for this MIB module. The formats of objects of this type are determined by a corresponding object with syntax AddressFamilyNumbers, and thus every object defined using this TC must identify the object with syntax AddressFamilyNumbers that specifies its type. The syntax and semantics of this object depend on the identified AddressFamilyNumbers object as follows: AddressFamilyNumbers this object ==================== =========== ipV4(1) restricted to the same syntax and semantics as the InetAddressIPv4 TC. ipV6(2) restricted to the same syntax and semantics as the InetAddressIPv6 TC. fibreChannelWWPN (22) & fibreChannelWWNN(23) restricted to the same syntax and semantics as the FcNameIdOrZero TC. Types other than the above should not be used unless the corresponding format of the IpsAuthAddress object is further specified (e.g., in a future revision of this TC).
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..255)  

IpsAuthInstanceAttributesEntry  
SEQUENCE    
  ipsAuthInstIndex Unsigned32
  ipsAuthInstDescr SnmpAdminString
  ipsAuthInstStorageType StorageType

IpsAuthIdentAttributesEntry  
SEQUENCE    
  ipsAuthIdentIndex Unsigned32
  ipsAuthIdentDescription SnmpAdminString
  ipsAuthIdentRowStatus RowStatus
  ipsAuthIdentStorageType StorageType

IpsAuthIdentNameAttributesEntry  
SEQUENCE    
  ipsAuthIdentNameIndex Unsigned32
  ipsAuthIdentName SnmpAdminString
  ipsAuthIdentNameRowStatus RowStatus
  ipsAuthIdentNameStorageType StorageType

IpsAuthIdentAddrAttributesEntry  
SEQUENCE    
  ipsAuthIdentAddrIndex Unsigned32
  ipsAuthIdentAddrType AddressFamilyNumbers
  ipsAuthIdentAddrStart IpsAuthAddress
  ipsAuthIdentAddrEnd IpsAuthAddress
  ipsAuthIdentAddrRowStatus RowStatus
  ipsAuthIdentAddrStorageType StorageType

IpsAuthCredentialAttributesEntry  
SEQUENCE    
  ipsAuthCredIndex Unsigned32
  ipsAuthCredAuthMethod AutonomousType
  ipsAuthCredRowStatus RowStatus
  ipsAuthCredStorageType StorageType

IpsAuthCredChapAttributesEntry  
SEQUENCE    
  ipsAuthCredChapUserName SnmpAdminString
  ipsAuthCredChapRowStatus RowStatus
  ipsAuthCredChapStorageType StorageType

IpsAuthCredSrpAttributesEntry  
SEQUENCE    
  ipsAuthCredSrpUserName SnmpAdminString
  ipsAuthCredSrpRowStatus RowStatus
  ipsAuthCredSrpStorageType StorageType

IpsAuthCredKerbAttributesEntry  
SEQUENCE    
  ipsAuthCredKerbPrincipal SnmpAdminString
  ipsAuthCredKerbRowStatus RowStatus
  ipsAuthCredKerbStorageType StorageType

Defined Values

ipsAuthMibModule 1.3.6.1.2.1.141
The IP Storage Authorization MIB module. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4545; see the RFC itself for full legal notices.
MODULE-IDENTITY    

ipsAuthNotifications 1.3.6.1.2.1.141.0
OBJECT IDENTIFIER    

ipsAuthObjects 1.3.6.1.2.1.141.1
OBJECT IDENTIFIER    

ipsAuthConformance 1.3.6.1.2.1.141.2
OBJECT IDENTIFIER    

ipsAuthDescriptors 1.3.6.1.2.1.141.1.1
OBJECT IDENTIFIER    

ipsAuthMethodTypes 1.3.6.1.2.1.141.1.1.1
Registration point for Authentication Method Types.
Status: current Access: read-only
OBJECT-IDENTITY    

ipsAuthMethodNone 1.3.6.1.2.1.141.1.1.1.1
The authoritative identifier when no authentication method is used.
Status: current Access: read-only
OBJECT-IDENTITY    

ipsAuthMethodSrp 1.3.6.1.2.1.141.1.1.1.2
The authoritative identifier when the authentication method is SRP.
Status: current Access: read-only
OBJECT-IDENTITY    

ipsAuthMethodChap 1.3.6.1.2.1.141.1.1.1.3
The authoritative identifier when the authentication method is CHAP.
Status: current Access: read-only
OBJECT-IDENTITY    

ipsAuthMethodKerberos 1.3.6.1.2.1.141.1.1.1.4
The authoritative identifier when the authentication method is Kerberos.
Status: current Access: read-only
OBJECT-IDENTITY    

ipsAuthInstance 1.3.6.1.2.1.141.1.2
OBJECT IDENTIFIER    

ipsAuthInstanceAttributesTable 1.3.6.1.2.1.141.1.2.2
A list of Authorization instances present on the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpsAuthInstanceAttributesEntry

ipsAuthInstanceAttributesEntry 1.3.6.1.2.1.141.1.2.2.1
An entry (row) containing management information applicable to a particular Authorization instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpsAuthInstanceAttributesEntry  

ipsAuthInstIndex 1.3.6.1.2.1.141.1.2.2.1.1
An arbitrary integer used to uniquely identify a particular authorization instance. This index value must not be modified or reused by an agent unless a reboot has occurred. An agent should attempt to keep this value persistent across reboots.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ipsAuthInstDescr 1.3.6.1.2.1.141.1.2.2.1.2
A character string, determined by the implementation to describe the authorization instance. When only a single instance is present, this object may be set to the zero-length string; with multiple authorization instances, it must be set to a unique value in an implementation-dependent manner to describe the purpose of the respective instance. If this is deployed in a master agent with more than one subagent implementing this MIB module, the master agent is responsible for ensuring that this object is unique across all subagents.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

ipsAuthInstStorageType 1.3.6.1.2.1.141.1.2.2.1.3
The storage type for all read-write objects within this row. Rows in this table are always created via an external process, and may have a storage type of readOnly or permanent. Conceptual rows having the value 'permanent' need not allow write access to any columnar objects in the row. If this object has the value 'volatile', modifications to read-write objects in this row are not persistent across reboots. If this object has the value 'nonVolatile', modifications to objects in this row are persistent. An implementation may choose to allow this object to be set to either 'nonVolatile' or 'volatile', allowing the management application to choose this behavior.
Status: current Access: read-write
OBJECT-TYPE    
  StorageType  

ipsAuthIdentity 1.3.6.1.2.1.141.1.3
OBJECT IDENTIFIER    

ipsAuthIdentAttributesTable 1.3.6.1.2.1.141.1.3.1
A list of user identities, each belonging to a particular ipsAuthInstance.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpsAuthIdentAttributesEntry

ipsAuthIdentAttributesEntry 1.3.6.1.2.1.141.1.3.1.1
An entry (row) containing management information describing a user identity within an authorization instance on this node.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpsAuthIdentAttributesEntry  

ipsAuthIdentIndex 1.3.6.1.2.1.141.1.3.1.1.1
An arbitrary integer used to uniquely identify a particular identity instance within an authorization instance present on the node. This index value must not be modified or reused by an agent unless a reboot has occurred. An agent should attempt to keep this value persistent across reboots.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ipsAuthIdentDescription 1.3.6.1.2.1.141.1.3.1.1.2
A character string describing this particular identity.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

ipsAuthIdentRowStatus 1.3.6.1.2.1.141.1.3.1.1.3
This field allows entries to be dynamically added and removed from this table via SNMP. When adding a row to this table, all non-Index/RowStatus objects must be set. Rows may be discarded using RowStatus. The value of ipsAuthIdentDescription may be set while ipsAuthIdentRowStatus is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipsAuthIdentStorageType 1.3.6.1.2.1.141.1.3.1.1.4
The storage type for all read-create objects in this row. Rows in this table that were created through an external process may have a storage type of readOnly or permanent. Conceptual rows having the value 'permanent' need not allow write access to any columnar objects in the row.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

ipsAuthIdentityName 1.3.6.1.2.1.141.1.4
OBJECT IDENTIFIER    

ipsAuthIdentNameAttributesTable 1.3.6.1.2.1.141.1.4.1
A list of unique names that can be used to positively identify a particular user identity.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpsAuthIdentNameAttributesEntry

ipsAuthIdentNameAttributesEntry 1.3.6.1.2.1.141.1.4.1.1
An entry (row) containing management information applicable to a unique identity name, which can be used to identify a user identity within a particular authorization instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpsAuthIdentNameAttributesEntry  

ipsAuthIdentNameIndex 1.3.6.1.2.1.141.1.4.1.1.1
An arbitrary integer used to uniquely identify a particular identity name instance within an ipsAuthIdentity within an authorization instance. This index value must not be modified or reused by an agent unless a reboot has occurred. An agent should attempt to keep this value persistent across reboots.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ipsAuthIdentName 1.3.6.1.2.1.141.1.4.1.1.2
A character string that is the unique name of an identity that may be used to identify this ipsAuthIdent entry.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

ipsAuthIdentNameRowStatus 1.3.6.1.2.1.141.1.4.1.1.3
This field allows entries to be dynamically added and removed from this table via SNMP. When adding a row to this table, all non-Index/RowStatus objects must be set. Rows may be discarded using RowStatus. The value of ipsAuthIdentName may be set when this value is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipsAuthIdentNameStorageType 1.3.6.1.2.1.141.1.4.1.1.4
The storage type for all read-create objects in this row. Rows in this table that were created through an external process may have a storage type of readOnly or permanent. Conceptual rows having the value 'permanent' need not allow write access to any columnar objects in the row.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

ipsAuthIdentityAddress 1.3.6.1.2.1.141.1.5
OBJECT IDENTIFIER    

ipsAuthIdentAddrAttributesTable 1.3.6.1.2.1.141.1.5.1
A list of address ranges that are allowed to serve as the endpoint addresses of a particular identity. An address range includes a starting and ending address and an optional netmask, and an address type indicator, which can specify whether the address is IPv4, IPv6, FC-WWPN, or FC-WWNN.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpsAuthIdentAddrAttributesEntry

ipsAuthIdentAddrAttributesEntry 1.3.6.1.2.1.141.1.5.1.1
An entry (row) containing management information applicable to an address range that is used as part of the authorization of an identity within an authorization instance on this node.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpsAuthIdentAddrAttributesEntry  

ipsAuthIdentAddrIndex 1.3.6.1.2.1.141.1.5.1.1.1
An arbitrary integer used to uniquely identify a particular ipsAuthIdentAddress instance within an ipsAuthIdentity within an authorization instance present on the node. This index value must not be modified or reused by an agent unless a reboot has occurred. An agent should attempt to keep this value persistent across reboots.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ipsAuthIdentAddrType 1.3.6.1.2.1.141.1.5.1.1.2
The address types used in the ipsAuthIdentAddrStart and ipsAuthAddrEnd objects. This type is taken from the IANA address family types.
Status: current Access: read-create
OBJECT-TYPE    
  AddressFamilyNumbers  

ipsAuthIdentAddrStart 1.3.6.1.2.1.141.1.5.1.1.3
The starting address of the allowed address range. The format of this object is determined by ipsAuthIdentAddrType.
Status: current Access: read-create
OBJECT-TYPE    
  IpsAuthAddress  

ipsAuthIdentAddrEnd 1.3.6.1.2.1.141.1.5.1.1.4
The ending address of the allowed address range. If the ipsAuthIdentAddrEntry specifies a single address, this shall match the ipsAuthIdentAddrStart. The format of this object is determined by ipsAuthIdentAddrType.
Status: current Access: read-create
OBJECT-TYPE    
  IpsAuthAddress  

ipsAuthIdentAddrRowStatus 1.3.6.1.2.1.141.1.5.1.1.5
This field allows entries to be dynamically added and removed from this table via SNMP. When adding a row to this table, all non-Index/RowStatus objects must be set. Rows may be discarded using RowStatus. The values of ipsAuthIdentAddrStart and ipsAuthIdentAddrEnd may be set when this value is 'active'. The value of ipsAuthIdentAddrType may not be set when this value is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipsAuthIdentAddrStorageType 1.3.6.1.2.1.141.1.5.1.1.6
The storage type for all read-create objects in this row. Rows in this table that were created through an external process may have a storage type of readOnly or permanent. Conceptual rows having the value 'permanent' need not allow write access to any columnar objects in the row.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

ipsAuthCredential 1.3.6.1.2.1.141.1.6
OBJECT IDENTIFIER    

ipsAuthCredentialAttributesTable 1.3.6.1.2.1.141.1.6.1
A list of credentials related to user identities that are allowed as valid authenticators of the particular identity.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpsAuthCredentialAttributesEntry

ipsAuthCredentialAttributesEntry 1.3.6.1.2.1.141.1.6.1.1
An entry (row) containing management information applicable to a credential that verifies a user identity within an authorization instance. To provide complete information in this MIB for a credential, the management station must not only create the row in this table but must also create a row in another table, where the other table is determined by the value of ipsAuthCredAuthMethod, e.g., if ipsAuthCredAuthMethod has the value ipsAuthMethodChap, a row must be created in the ipsAuthCredChapAttributesTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpsAuthCredentialAttributesEntry  

ipsAuthCredIndex 1.3.6.1.2.1.141.1.6.1.1.1
An arbitrary integer used to uniquely identify a particular Credential instance within an instance present on the node. This index value must not be modified or reused by an agent unless a reboot has occurred. An agent should attempt to keep this value persistent across reboots.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ipsAuthCredAuthMethod 1.3.6.1.2.1.141.1.6.1.1.2
This object contains an OBJECT IDENTIFIER that identifies the authentication method used with this credential. When a row is created in this table, a corresponding row must be created by the management station in a corresponding table specified by this value. When a row is deleted from this table, the corresponding row must be automatically deleted by the agent in the corresponding table specified by this value. If the value of this object is ipsAuthMethodNone, no corresponding rows are created or deleted from other tables. Some standardized values for this object are defined within the ipsAuthMethodTypes subtree.
Status: current Access: read-create
OBJECT-TYPE    
  AutonomousType  

ipsAuthCredRowStatus 1.3.6.1.2.1.141.1.6.1.1.3
This field allows entries to be dynamically added and removed from this table via SNMP. When adding a row to this table, all non-Index/RowStatus objects must be set. Rows may be discarded using RowStatus. The value of ipsAuthCredAuthMethod must not be changed while this row is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipsAuthCredStorageType 1.3.6.1.2.1.141.1.6.1.1.4
The storage type for all read-create objects in this row. Rows in this table that were created through an external process may have a storage type of readOnly or permanent. Conceptual rows having the value 'permanent' need not allow write access to any columnar objects in the row.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

ipsAuthCredChap 1.3.6.1.2.1.141.1.7
OBJECT IDENTIFIER    

ipsAuthCredChapAttributesTable 1.3.6.1.2.1.141.1.7.1
A list of CHAP attributes for credentials that use ipsAuthMethodChap as their ipsAuthCredAuthMethod. A row in this table can only exist when an instance of the ipsAuthCredAuthMethod object exists (or is created simultaneously) having the same instance identifiers and a value of 'ipsAuthMethodChap'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpsAuthCredChapAttributesEntry

ipsAuthCredChapAttributesEntry 1.3.6.1.2.1.141.1.7.1.1
An entry (row) containing management information applicable to a credential that uses ipsAuthMethodChap as their ipsAuthCredAuthMethod. When a row is created in ipsAuthCredentialAttributesTable with ipsAuthCredAuthMethod = ipsAuthCredChap, the management station must create a corresponding row in this table. When a row is deleted from ipsAuthCredentialAttributesTable with ipsAuthCredAuthMethod = ipsAuthCredChap, the agent must delete the corresponding row (if any) in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpsAuthCredChapAttributesEntry  

ipsAuthCredChapUserName 1.3.6.1.2.1.141.1.7.1.1.1
A character string containing the CHAP user name for this credential.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

ipsAuthCredChapRowStatus 1.3.6.1.2.1.141.1.7.1.1.2
This field allows entries to be dynamically added and removed from this table via SNMP. When adding a row to this table, all non-Index/RowStatus objects must be set. Rows may be discarded using RowStatus. The value of ipsAuthCredChapUserName may be changed while this row is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipsAuthCredChapStorageType 1.3.6.1.2.1.141.1.7.1.1.3
The storage type for all read-create objects in this row. Rows in this table that were created through an external process may have a storage type of readOnly or permanent. Conceptual rows having the value 'permanent' need not allow write access to any columnar objects in the row.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

ipsAuthCredSrp 1.3.6.1.2.1.141.1.8
OBJECT IDENTIFIER    

ipsAuthCredSrpAttributesTable 1.3.6.1.2.1.141.1.8.1
A list of SRP attributes for credentials that use ipsAuthMethodSrp as its ipsAuthCredAuthMethod. A row in this table can only exist when an instance of the ipsAuthCredAuthMethod object exists (or is created simultaneously) having the same instance identifiers and a value of 'ipsAuthMethodSrp'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpsAuthCredSrpAttributesEntry

ipsAuthCredSrpAttributesEntry 1.3.6.1.2.1.141.1.8.1.1
An entry (row) containing management information applicable to a credential that uses ipsAuthMethodSrp as their ipsAuthCredAuthMethod. When a row is created in ipsAuthCredentialAttributesTable with ipsAuthCredAuthMethod = ipsAuthCredSrp, the management station must create a corresponding row in this table. When a row is deleted from ipsAuthCredentialAttributesTable with ipsAuthCredAuthMethod = ipsAuthCredSrp, the agent must delete the corresponding row (if any) in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpsAuthCredSrpAttributesEntry  

ipsAuthCredSrpUserName 1.3.6.1.2.1.141.1.8.1.1.1
A character string containing the SRP user name for this credential.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

ipsAuthCredSrpRowStatus 1.3.6.1.2.1.141.1.8.1.1.2
This field allows entries to be dynamically added and removed from this table via SNMP. When adding a row to this table, all non-Index/RowStatus objects must be set. Rows may be discarded using RowStatus. The value of ipsAuthCredSrpUserName may be changed while the status of this row is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipsAuthCredSrpStorageType 1.3.6.1.2.1.141.1.8.1.1.3
The storage type for all read-create objects in this row. Rows in this table that were created through an external process may have a storage type of readOnly or permanent. Conceptual rows having the value 'permanent' need not allow write access to any columnar objects in the row.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

ipsAuthCredKerberos 1.3.6.1.2.1.141.1.9
OBJECT IDENTIFIER    

ipsAuthCredKerbAttributesTable 1.3.6.1.2.1.141.1.9.1
A list of Kerberos attributes for credentials that use ipsAuthMethodKerberos as their ipsAuthCredAuthMethod. A row in this table can only exist when an instance of the ipsAuthCredAuthMethod object exists (or is created simultaneously) having the same instance identifiers and a value of 'ipsAuthMethodKerb'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpsAuthCredKerbAttributesEntry

ipsAuthCredKerbAttributesEntry 1.3.6.1.2.1.141.1.9.1.1
An entry (row) containing management information applicable to a credential that uses ipsAuthMethodKerberos as its ipsAuthCredAuthMethod. When a row is created in ipsAuthCredentialAttributesTable with ipsAuthCredAuthMethod = ipsAuthCredKerberos, the management station must create a corresponding row in this table. When a row is deleted from ipsAuthCredentialAttributesTable with ipsAuthCredAuthMethod = ipsAuthCredKerberos, the agent must delete the corresponding row (if any) in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpsAuthCredKerbAttributesEntry  

ipsAuthCredKerbPrincipal 1.3.6.1.2.1.141.1.9.1.1.1
A character string containing a Kerberos principal for this credential.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

ipsAuthCredKerbRowStatus 1.3.6.1.2.1.141.1.9.1.1.2
This field allows entries to be dynamically added and removed from this table via SNMP. When adding a row to this table, all non-Index/RowStatus objects must be set. Rows may be discarded using RowStatus. The value of ipsAuthCredKerbPrincipal may be changed while this row is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipsAuthCredKerbStorageType 1.3.6.1.2.1.141.1.9.1.1.3
The storage type for all read-create objects in this row. Rows in this table that were created through an external process may have a storage type of readOnly or permanent. Conceptual rows having the value 'permanent' need not allow write access to any columnar objects in the row.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

ipsAuthCompliances 1.3.6.1.2.1.141.2.1
OBJECT IDENTIFIER    

ipsAuthGroups 1.3.6.1.2.1.141.2.2
OBJECT IDENTIFIER    

ipsAuthInstanceAttributesGroup 1.3.6.1.2.1.141.2.2.1
A collection of objects providing information about authorization instances.
Status: current Access: read-create
OBJECT-GROUP    

ipsAuthIdentAttributesGroup 1.3.6.1.2.1.141.2.2.2
A collection of objects providing information about user identities within an authorization instance.
Status: current Access: read-create
OBJECT-GROUP    

ipsAuthIdentNameAttributesGroup 1.3.6.1.2.1.141.2.2.3
A collection of objects providing information about user names within user identities within an authorization instance.
Status: current Access: read-create
OBJECT-GROUP    

ipsAuthIdentAddrAttributesGroup 1.3.6.1.2.1.141.2.2.4
A collection of objects providing information about address ranges within user identities within an authorization instance.
Status: current Access: read-create
OBJECT-GROUP    

ipsAuthIdentCredAttributesGroup 1.3.6.1.2.1.141.2.2.5
A collection of objects providing information about credentials within user identities within an authorization instance.
Status: current Access: read-create
OBJECT-GROUP    

ipsAuthIdentChapAttrGroup 1.3.6.1.2.1.141.2.2.6
A collection of objects providing information about CHAP credentials within user identities within an authorization instance.
Status: current Access: read-create
OBJECT-GROUP    

ipsAuthIdentSrpAttrGroup 1.3.6.1.2.1.141.2.2.7
A collection of objects providing information about SRP credentials within user identities within an authorization instance.
Status: current Access: read-create
OBJECT-GROUP    

ipsAuthIdentKerberosAttrGroup 1.3.6.1.2.1.141.2.2.8
A collection of objects providing information about Kerberos credentials within user identities within an authorization instance.
Status: current Access: read-create
OBJECT-GROUP    

ipsAuthComplianceV1 1.3.6.1.2.1.141.2.1.1
Initial version of compliance statement based on initial version of this MIB module. The Instance and Identity groups are mandatory; at least one of the other groups (Name, Address, Credential, Certificate) is also mandatory for any given implementation.
Status: current Access: read-only
MODULE-COMPLIANCE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor