ITOUCH-REPEATER-MIB

File: ITOUCH-REPEATER-MIB.mib (99251 bytes)

Imported modules

RFC1155-SMI	RFC1213-MIB	BRIDGE-MIB
RFC-1212	RFC-1215	ITOUCH-MIB

Imported symbols

Counter	TimeTicks	Gauge
DisplayString	MacAddress	OBJECT-TYPE
TRAP-TYPE	iTouch	TypedAddress

Defined Types

Segment
INTEGER	a(1), b(2), c(3), d(4), e(5), f(6), g(7), h(8), i(9), j(10), k(11), l(12), m(13), n(14), o(15), p(16), q(17), r(18), s(19), t(20), u(21), v(22), w(23), x(24), y(25), z(26), disabled(27), notApplicable(28)

Repeater
INTEGER	notApplicable(1), repeater1(2), repeater2(3), repeater3(4)

RepeaterGroupEntry
SEQUENCE
	repeaterGroupIndex	INTEGER
	repeaterGroupSQE	Counter
	repeaterGroupJabbers	Counter
	repeaterGroupSegment	Segment
	repeaterGroupSecurityLock	INTEGER
	repeaterGroupIOCardType	INTEGER
	repeaterGroupIOCardFirmwareVersion	INTEGER
	repeaterGroupIOCardOperStatus	INTEGER
	repeaterGroupManagement	INTEGER
	repeaterGroupRepeaterNumber	INTEGER
	repeaterGroupRepeaterHardwareVersion	INTEGER
	repeaterGroupManagerRepeater	Repeater
	repeaterGroupFifoErrors	Counter
	repeaterGroupCpuUtilization	INTEGER
	repeaterGroupMemoryUtilization	INTEGER
	repeaterGroupAlarmCount	INTEGER

RepeaterPortEntry
SEQUENCE
	repeaterPortGroupIndex	INTEGER
	repeaterPortIndex	INTEGER
	repeaterPortName	DisplayString
	repeaterPortAutoPolarity	INTEGER
	repeaterPortPolarityDirection	INTEGER
	repeaterPortPulse	INTEGER
	repeaterPortPulseStatus	INTEGER
	repeaterPortPulseLosses	Counter
	repeaterPortDistance	INTEGER
	repeaterPortSofMissing	Counter
	repeaterPortMCVs	Counter
	repeaterPortZero	INTEGER
	repeaterPortSinceZero	TimeTicks
	repeaterPortAccessAction	INTEGER
	repeaterPortAccessState	INTEGER
	repeaterPortAccessType	INTEGER
	repeaterPortAccessAllStatus	INTEGER
	repeaterPortPortLastViolationAddress	MacAddress
	repeaterPortPortAddressViolations	Counter
	repeaterPortSegment	Segment
	repeaterPortAccessLearn	INTEGER
	repeaterPortEthernetRepeater	INTEGER
	repeaterPortRepeatersAllowed	OCTET STRING
	repeaterPortGlobalSecurityAddress	MacAddress
	repeaterPortGlobalAddressChanges	Counter
	repeaterPortPercentUtilization	Gauge

RepeaterPortAccessEntry
SEQUENCE
	repeaterPortAccessGroupIndex	INTEGER
	repeaterPortAccessPortIndex	INTEGER
	repeaterPortAccessAddress	MacAddress
	repeaterPortAccessStatus	INTEGER

RepeaterPort2Entry
SEQUENCE
	repeaterPort2RmonOctets	Counter
	repeaterPort2RmonPkts	Counter
	repeaterPort2RmonBroadcastPkts	Counter
	repeaterPort2RmonMulticastPkts	Counter
	repeaterPort2RmonCRCAlignErrors	Counter
	repeaterPort2RmonPkts64Octets	Counter
	repeaterPort2RmonPkts65to127Octets	Counter
	repeaterPort2RmonPkts128to255Octets	Counter
	repeaterPort2RmonPkts256to511Octets	Counter
	repeaterPort2RmonPkts512to1023Octets	Counter
	repeaterPort2RmonPkts1024to1518Octets	Counter
	repeaterPort2TrafficRatio	INTEGER
	repeaterPort2CollisionRatio	INTEGER
	repeaterPort2ErrorRatio	INTEGER
	repeaterPort2BroadcastRatio	INTEGER
	repeaterPort2MulticastRatio	INTEGER
	repeaterPort2UnicastRatio	INTEGER

RepeaterSlotSegmentEntry
SEQUENCE
	repeaterSlotIndex	INTEGER
	repeaterSlotSegment	Segment
	repeaterSlotSegmentStatus	INTEGER

RepeaterSecurityPortEntry
SEQUENCE
	repeaterSecurityPortUnicast	INTEGER
	repeaterSecurityPortMulticast	INTEGER
	repeaterSecurityPortAllStatus	INTEGER
	repeaterSecurityPortSecurityLearn	INTEGER

RepeaterSecurityEntry
SEQUENCE
	repeaterSecurityGroupIndex	INTEGER
	repeaterSecurityPortIndex	INTEGER
	repeaterSecurityAddress	MacAddress
	repeaterSecurityStatus	INTEGER
	repeaterSecurityAction	INTEGER

RepeaterSecurityGlobalAddressEntry
SEQUENCE
	repeaterSecurityGlobalAddress	MacAddress
	repeaterSecurityGlobalAddressStatus	INTEGER
	repeaterSecurityGlobalAddressAction	INTEGER

RepeaterRepeaterEntry
SEQUENCE
	repeaterRepeaterGroupIndex	INTEGER
	repeaterRepeaterIndex	INTEGER
	repeaterRepeaterSegment	Segment
	repeaterRepeaterReports	INTEGER
	repeaterRepeaterCollisions	Counter
	repeaterRepeaterJabbers	Counter
	repeaterRepeaterSQE	Counter
	repeaterRepeaterFifoOverflows	Counter
	repeaterRepeaterZero	INTEGER
	repeaterRepeaterSinceZero	TimeTicks
	repeaterRepeaterSegmentsAllowed	OCTET STRING
	repeaterRepeaterTotalOctets	Counter
	repeaterRepeaterTotalFrames	Counter
	repeaterRepeaterPercentUtilization	Gauge

RepeaterRedundancyGroupEntry
SEQUENCE
	repeaterRedundancyGroupGroupIndex	INTEGER
	repeaterRedundancyGroupStatus	INTEGER
	repeaterRedundancyGroupName	DisplayString
	repeaterRedundancyGroupAdminState	INTEGER
	repeaterRedundancyGroupTestInterval	INTEGER
	repeaterRedundancyGroupRollbackAdminState	INTEGER
	repeaterRedundancyGroupRollbackInterval	INTEGER
	repeaterRedundancyGroupOperPath	INTEGER
	repeaterRedundancyGroupPathChanges	Counter
	repeaterRedundancyGroupRollbackAttempts	Counter
	repeaterRedundancyGroupZero	INTEGER
	repeaterRedundancyGroupSinceZero	TimeTicks
	repeaterRedundancyGroupConfigStatus	INTEGER

RepeaterRedundancyPathEntry
SEQUENCE
	repeaterRedundancyPathGroupIndex	INTEGER
	repeaterRedundancyPathPathIndex	INTEGER
	repeaterRedundancyPathStatus	INTEGER
	repeaterRedundancyPathSlot	INTEGER
	repeaterRedundancyPathPort	INTEGER
	repeaterRedundancyPathPriority	INTEGER
	repeaterRedundancyPathActivate	INTEGER
	repeaterRedundancyPathTimeout	INTEGER
	repeaterRedundancyPathRetryCount	INTEGER
	repeaterRedundancyPathTestAttempts	Counter
	repeaterRedundancyPathLastTestStatus	INTEGER
	repeaterRedundancyPathDisposition	INTEGER
	repeaterRedundancyPathConfigStatus	INTEGER
	repeaterRedundancyPathAdminState	INTEGER

RepeaterRedundancyAddressEntry
SEQUENCE
	repeaterRedundancyAddressGroupIndex	INTEGER
	repeaterRedundancyAddressPathIndex	INTEGER
	repeaterRedundancyAddressAddress	TypedAddress
	repeaterRedundancyAddressStatus	INTEGER
	repeaterRedundancyAddressResponses	Counter
	repeaterRedundancyAddressLastTestStatus	INTEGER

Defined Values

hubDeprecated		1.3.6.1.4.1.33.9
OBJECT IDENTIFIER

xRepeater		1.3.6.1.4.1.33.17
OBJECT IDENTIFIER

xRepeaterInfo		1.3.6.1.4.1.33.17.1
OBJECT IDENTIFIER

xRepeaterGroupInfo		1.3.6.1.4.1.33.17.2
OBJECT IDENTIFIER

xRepeaterPortInfo		1.3.6.1.4.1.33.17.3
OBJECT IDENTIFIER

xRepeaterSlotInfo		1.3.6.1.4.1.33.17.4
OBJECT IDENTIFIER

xRepeaterSecurity		1.3.6.1.4.1.33.17.5
OBJECT IDENTIFIER

xRepeaterRepeater		1.3.6.1.4.1.33.17.6
OBJECT IDENTIFIER

xRepeaterRedundancy		1.3.6.1.4.1.33.17.7
OBJECT IDENTIFIER

repeaterAccessViolation		1.3.6.1.4.1.33.17.1.1
Controls action to take when an access violation occurs.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	both(1), disable(2), trap(3)

repeaterMyGroup		1.3.6.1.4.1.33.17.1.2
The index value of the group that is directly associated with the agent. The snmp support for the group associated with the agent is a superset of the support for other groups.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterFifoOverflows		1.3.6.1.4.1.33.17.1.3
Deprecated, use repeaterRepeaterFifoOverflows in the repeaterRepeater group for the desired repeater.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter

repeaterLEDDisplay		1.3.6.1.4.1.33.17.1.4
Controls reason for flashing front panel LEDs.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	activity(1), collisions(2)

repeaterReports		1.3.6.1.4.1.33.17.1.5
Deprecated, use repeaterRepeaterReports in the repeaterRepeater group for the desired repeater on which report generation is to be controlled.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterHealthTrap		1.3.6.1.4.1.33.17.1.6
Controls the generation of the repeater health trap.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterStatusChangeTrap		1.3.6.1.4.1.33.17.1.7
Controls the generation of the repeater status change trap.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterAccessViolationTrap		1.3.6.1.4.1.33.17.1.8
Controls the generation of the repeater access violation trap.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterIntegrityLossTrap		1.3.6.1.4.1.33.17.1.9
Controls the generation of the repeater integrity loss trap.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterRedundancyPathChangeTrap		1.3.6.1.4.1.33.17.1.10
Controls the generation of the repeater redundancy path change trap.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterGroupTable		1.3.6.1.4.1.33.17.2.1
Table of descriptive and status information about the groups.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RepeaterGroupEntry

repeaterGroupEntry		1.3.6.1.4.1.33.17.2.1.1
An entry in the table, containing information about a group.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	RepeaterGroupEntry

repeaterGroupIndex		1.3.6.1.4.1.33.17.2.1.1.1
This variable identifies the group within the repeater for which this entry contains information. This value is the same as rptrGroupIndex.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterGroupSQE		1.3.6.1.4.1.33.17.2.1.1.2
Deprecated, use repeaterRepeaterSQE in the repeaterRepeaterGroup for the SQE count on the desired repeater. This object will always return the count for repeater #1.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter

repeaterGroupJabbers		1.3.6.1.4.1.33.17.2.1.1.3
Deprecated, use repeaterRepeaterJabbers in the repeaterRepeaterGroup for the Jabber count on the desired repeater. This object will always return the count for repeater #1.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter

repeaterGroupSegment		1.3.6.1.4.1.33.17.2.1.1.4
Deprecated, use repeaterRepeaterSegment in the repeaterRepeaterGroup to control the segment mapping for the desired repeater. This object will always control the mapping for repeater #1.
Status: deprecated	Access: read-write
OBJECT-TYPE
	Segment

repeaterGroupSecurityLock		1.3.6.1.4.1.33.17.2.1.1.5
This variable indicates the state of security lockdown on an unmanaged repeater. The only writable value is 'unlocked'.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	unlocked(1), locked(2)

repeaterGroupIOCardType		1.3.6.1.4.1.33.17.2.1.1.6
The hardware type of the I/O card, as defined in ITouch Assigned Numbers.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterGroupIOCardFirmwareVersion		1.3.6.1.4.1.33.17.2.1.1.7
The firmware revision level of the I/O card ROM.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterGroupIOCardOperStatus		1.3.6.1.4.1.33.17.2.1.1.8
Relative to the chassis, the current operating status of the I/O card.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	loadRequested(1), loading(2), dumpRequested(3), dumping(4), paramRequested(5), paramLoading(6), running(7), initializing(8), attended(9), internal10(10), internal11(11), inhibited(12), maxserverCard(13), invalidConfigStorage(14), securityLockdown(15)

repeaterGroupManagement		1.3.6.1.4.1.33.17.2.1.1.9
This variable indicates the level of management control and observation available.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	minimal(1), full(2)

repeaterGroupRepeaterNumber		1.3.6.1.4.1.33.17.2.1.1.10
The number of logical repeaters visible via this repeater.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterGroupRepeaterHardwareVersion		1.3.6.1.4.1.33.17.2.1.1.11
The repeater chip set hardware revision level.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterGroupManagerRepeater		1.3.6.1.4.1.33.17.2.1.1.12
The logical repeater to which the manager card, if present, is attached.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Repeater

repeaterGroupFifoErrors		1.3.6.1.4.1.33.17.2.1.1.13
This variable will reflect the number of times that the report FIFO has gone out of synchronization.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterGroupCpuUtilization		1.3.6.1.4.1.33.17.2.1.1.14
The average CPU utilization for the processor which maintains statistics and implements monitoring for the group, expressed as percentage times 100.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..10000

repeaterGroupMemoryUtilization		1.3.6.1.4.1.33.17.2.1.1.15
The current memory utilization for the processor which maintains statistics and implements monitoring for the group, expressed as percentage used times 100.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..10000

repeaterGroupAlarmCount		1.3.6.1.4.1.33.17.2.1.1.16
The number of alarms currently being monitored by the processor for comparison with RMON thresholds.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterPortTable		1.3.6.1.4.1.33.17.3.1
Table of descriptive and status information about the ports.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RepeaterPortEntry

repeaterPortEntry		1.3.6.1.4.1.33.17.3.1.1
An entry in the table, containing information about a port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	RepeaterPortEntry

repeaterPortGroupIndex		1.3.6.1.4.1.33.17.3.1.1.1
This variable identifies the group containing the port for which this entry contains infromation.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterPortIndex		1.3.6.1.4.1.33.17.3.1.1.2
This variable identifies the port within the group within the repeater for which this entry contains management information. This value can never be greater than rptrGroupPortCapacity for the associated group.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterPortName		1.3.6.1.4.1.33.17.3.1.1.3
The port's display name.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..16)

repeaterPortAutoPolarity		1.3.6.1.4.1.33.17.3.1.1.4
Controls whether the port will automatically determine its polarity.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterPortPolarityDirection		1.3.6.1.4.1.33.17.3.1.1.5
If repeaterPortAutoPolarity is enabled, this is the current polarity of the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	reversed(1), normal(2), unknown(3)

repeaterPortPulse		1.3.6.1.4.1.33.17.3.1.1.6
Controls whether the port will periodically generate a test pulse to determine the status of the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterPortPulseStatus		1.3.6.1.4.1.33.17.3.1.1.7
If repeaterPortPulse is enabled, this is indicates whether the test pulse response is being detected.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notDetected(1), detected(2)

repeaterPortPulseLosses		1.3.6.1.4.1.33.17.3.1.1.8
The number of times that a test pulse has been sent and a response was not received.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPortDistance		1.3.6.1.4.1.33.17.3.1.1.9
Controls whether the port will support extended distances on the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterPortSofMissing		1.3.6.1.4.1.33.17.3.1.1.10
The number of times that alternating zero/one bits were seen after an inter-packet gap and were not followed by two one bits.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPortMCVs		1.3.6.1.4.1.33.17.3.1.1.11
The number of manchester violation errors detected on this port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPortZero		1.3.6.1.4.1.33.17.3.1.1.12
Control to zero the hub port's counters. The agent always returns 'ready' for this value. Setting the value to 'ready' has no effect.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ready(1), execute(2)

repeaterPortSinceZero		1.3.6.1.4.1.33.17.3.1.1.13
Number of time ticks since the port's counters were zeroed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

repeaterPortAccessAction		1.3.6.1.4.1.33.17.3.1.1.14
Control whether packets will be accepted or discarded if they are in the access list. The inverse action is applied to packets from all addresses not in the list.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	discard(1), accept(2)

repeaterPortAccessState		1.3.6.1.4.1.33.17.3.1.1.15
Indicates whether the port was disabled due to receiving a frame from an invalid source address.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), notDisabled(2)

repeaterPortAccessType		1.3.6.1.4.1.33.17.3.1.1.16
Indicates the type of the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	tenBaseT(1), aui(2), foirl(3), mac(4), lanbus(5), tenBase2(6), tenBaseFL(7)

repeaterPortAccessAllStatus		1.3.6.1.4.1.33.17.3.1.1.17
Setting this field to invalid will delete all access addresses associated with this port. Setting this field to valid has no effect.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	invalid(1), valid(2)

repeaterPortPortLastViolationAddress		1.3.6.1.4.1.33.17.3.1.1.18
Address that last caused an access violation.
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

repeaterPortPortAddressViolations		1.3.6.1.4.1.33.17.3.1.1.19
Number of access violations.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPortSegment		1.3.6.1.4.1.33.17.3.1.1.20
Returns the indirect mapping of the ethernet repeater to which this port is connected.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Segment

repeaterPortAccessLearn		1.3.6.1.4.1.33.17.3.1.1.21
Controls how the port will learn the source addresses that can come in on the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), single(2), continuous(3)

repeaterPortEthernetRepeater		1.3.6.1.4.1.33.17.3.1.1.22
For repeaters that implement non-proxy management of logical repeaters, this variable selects the logical Ethernet repeater to which the port is attached.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	repeater1(1), repeater2(2), repeater3(3)

repeaterPortRepeatersAllowed		1.3.6.1.4.1.33.17.3.1.1.23
The list of repeaters to which this port can be attached. The OCTET STRING contains a bitmap, with a bit for 'none' and one bit for each repeater, and enough octets for all the repeaters on the device. The high order bit of the first octet corresponds to 'none', the following bits correspond to the repeaters, in order, beginning with 1.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

repeaterPortGlobalSecurityAddress		1.3.6.1.4.1.33.17.3.1.1.24
This variable represents the global address which is currently applied to the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

repeaterPortGlobalAddressChanges		1.3.6.1.4.1.33.17.3.1.1.25
This variable represents the number of times since counters have been zeroed, that a global address change occured on the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPortPercentUtilization		1.3.6.1.4.1.33.17.3.1.1.26
This variable will reflect the percentage of a full ethernet load that this port has received since last zeroed. The value is calculated as '(8(bytesReceived + (20*framesReceived))) /107(time)'.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

repeaterPortAccessTable		1.3.6.1.4.1.33.17.3.2
Table of access control for the ports.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RepeaterPortAccessEntry

repeaterPortAccessEntry		1.3.6.1.4.1.33.17.3.2.1
An entry in the table, containing access information about a port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	RepeaterPortAccessEntry

repeaterPortAccessGroupIndex		1.3.6.1.4.1.33.17.3.2.1.1
This variable identifies the group containing the access entry for which this entry contains information. The group ID may only be that of the target agent. Specifying a group ID of an agent in a different slot will result in `badValue` being returned.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterPortAccessPortIndex		1.3.6.1.4.1.33.17.3.2.1.2
This variable identifies the port containing the access entry for which this entry contains information.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterPortAccessAddress		1.3.6.1.4.1.33.17.3.2.1.3
This value will be compared to the source address of all packets received on the port in applying the access action
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

repeaterPortAccessStatus		1.3.6.1.4.1.33.17.3.2.1.4
The status of the entry. Set to 'invalid' to remove the rule.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	invalid(1), valid(2)

repeaterPortAccessGroupIndexShadow		1.3.6.1.4.1.33.17.3.3
This variable identifies the group which contains a port to which an access address is to be assigned. The group ID may only be that of the target agent. Specifying a group ID of an agent in a different slot will result in `badValue` being returned.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

repeaterPortAccessPortIndexShadow		1.3.6.1.4.1.33.17.3.4
This variable identifies the port of a group to which an access address is to be assigned.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

repeaterPortAccessAddressShadow		1.3.6.1.4.1.33.17.3.5
This value contains the ethernet address which is to be added to the access address table for the port specified by repeaterPortAccessGroupIndexShadow and repeaterPortAccessPortIndexShadow.
Status: mandatory	Access: read-write
OBJECT-TYPE
	MacAddress

repeaterPortAccessStatusShadow		1.3.6.1.4.1.33.17.3.6
When read, this variable will always return 'ready'. When this variable is set to 'execute' the address specified by repeaterPortAccessAddressShadow will be added to the access address table for the port specified by repeaterPortAccessGroupIndexShadow and repeaterPortAccessPortIndexShadow. If any of the above variables are zero when this object is set to 'execute', 'bad value' will be returned.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ready(1), execute(2)

repeaterPort2Table		1.3.6.1.4.1.33.17.3.7
Table of more descriptive and status information about the ports.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RepeaterPort2Entry

repeaterPort2Entry		1.3.6.1.4.1.33.17.3.7.1
An entry in the table, containing information about a port. Index is identical to repeaterPortTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	RepeaterPort2Entry

repeaterPort2RmonOctets		1.3.6.1.4.1.33.17.3.7.1.1
The total number of octets of data (including those in bad packets) received on the port (excluding framing bits but including FCS octets).
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPort2RmonPkts		1.3.6.1.4.1.33.17.3.7.1.2
The total number of packets (including error packets) received on the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPort2RmonBroadcastPkts		1.3.6.1.4.1.33.17.3.7.1.3
The total number of good packets received on the port that were directed to the broadcast address.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPort2RmonMulticastPkts		1.3.6.1.4.1.33.17.3.7.1.4
The total number of good packets received on the port that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPort2RmonCRCAlignErrors		1.3.6.1.4.1.33.17.3.7.1.5
The total number of packets received on the port that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but were not an integral number of octets in length or had a bad Frame Check Sequence (FCS).
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPort2RmonPkts64Octets		1.3.6.1.4.1.33.17.3.7.1.6
The total number of packets (including error packets) received on the port that were 64 octets in length (excluding framing bits but including FCS octets).
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPort2RmonPkts65to127Octets		1.3.6.1.4.1.33.17.3.7.1.7
The total number of packets (including error packets) received on the port that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPort2RmonPkts128to255Octets		1.3.6.1.4.1.33.17.3.7.1.8
The total number of packets (including error packets) received on the port that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPort2RmonPkts256to511Octets		1.3.6.1.4.1.33.17.3.7.1.9
The total number of packets (including error packets) received on the port that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPort2RmonPkts512to1023Octets		1.3.6.1.4.1.33.17.3.7.1.10
The total number of packets (including error packets) received on the port that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPort2RmonPkts1024to1518Octets		1.3.6.1.4.1.33.17.3.7.1.11
The total number of packets (including error packets) received on the port that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterPort2TrafficRatio		1.3.6.1.4.1.33.17.3.7.1.12
The portion of segment bandwidth used by the port over a 5 second interval, expressed as percentage times 100.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..10000

repeaterPort2CollisionRatio		1.3.6.1.4.1.33.17.3.7.1.13
The ratio of collisions the port participated in to total packets over a 5 second interval, expressed as percentage times 100.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..10000

repeaterPort2ErrorRatio		1.3.6.1.4.1.33.17.3.7.1.14
The ratio of total number of error frames on the port to total packets over a 5 second interval, expressed as percentage times 100.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..10000

repeaterPort2BroadcastRatio		1.3.6.1.4.1.33.17.3.7.1.15
The ratio of good packets directed by the port to the broadcast address to total packets over a 5 second interval, expressed as percentage times 100.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..10000

repeaterPort2MulticastRatio		1.3.6.1.4.1.33.17.3.7.1.16
The ratio of good packets directed by the port to any multicast address (but not the broadcast address) to total packets over a 5 second interval, expressed as percentage times 100.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..10000

repeaterPort2UnicastRatio		1.3.6.1.4.1.33.17.3.7.1.17
The ratio of good packets directed by the port to any address other than a multicast or broadcast address to total packets over a 5 second interval, expressed as percentage times 100.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..10000

repeaterSlotSegmentTable		1.3.6.1.4.1.33.17.4.1
Deprecated, no replacement.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RepeaterSlotSegmentEntry

repeaterSlotSegmentEntry		1.3.6.1.4.1.33.17.4.1.1
Deprecated, no replacement.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RepeaterSlotSegmentEntry

repeaterSlotIndex		1.3.6.1.4.1.33.17.4.1.1.1
Deprecated, no replacement.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterSlotSegment		1.3.6.1.4.1.33.17.4.1.1.2
Deprecated, no replacement.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Segment

repeaterSlotSegmentStatus		1.3.6.1.4.1.33.17.4.1.1.3
Deprecated, no replacement.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterSecurityState		1.3.6.1.4.1.33.17.5.1
Controls whether security operation will be applied to all ports on the repeater. If security is not supported by the device, 'badValue' will be returned if the variable is set to 'enabled'.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterSecurityPortTable		1.3.6.1.4.1.33.17.5.2
Table of descriptive and status information about the ports.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RepeaterSecurityPortEntry

repeaterSecurityPortEntry		1.3.6.1.4.1.33.17.5.2.1
An entry in the table, containing information about a port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	RepeaterSecurityPortEntry

repeaterSecurityPortUnicast		1.3.6.1.4.1.33.17.5.2.1.1
The action to take when the destination address is unicast and does not have an entry in repeaterSecurityTable. If repeaterPortGroupIndex is equal to the group number of the agent, this object is read-write, otherwise it is read-only.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	jam(1), allow(2)

repeaterSecurityPortMulticast		1.3.6.1.4.1.33.17.5.2.1.2
The action to take when the destination address is multicast and does not have an entry in repeaterSecurityTable. If repeaterPortGroupIndex is equal to the group number of the agent, this object is read-write, otherwise it is read-only
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	jam(1), allow(2)

repeaterSecurityPortAllStatus		1.3.6.1.4.1.33.17.5.2.1.3
Setting this field to invalid will delete all security addresses associated with this port. Setting this field to valid has no effect. If repeaterPortGroupIndex is equal to the group number of the agent, this object is read-write, otherwise it is read-only
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	invalid(1), valid(2)

repeaterSecurityPortSecurityLearn		1.3.6.1.4.1.33.17.5.2.1.4
Controls how the port will learn the destination addresses that can be sent to the port. If repeaterPortGroupIndex is equal to the group number of the agent, this object is read-write, otherwise it is read-only
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), single(2), continuous(3)

repeaterSecurityTable		1.3.6.1.4.1.33.17.5.3
Table of security control for the ports.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RepeaterSecurityEntry

repeaterSecurityEntry		1.3.6.1.4.1.33.17.5.3.1
An entry in the table, containing security information about a port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	RepeaterSecurityEntry

repeaterSecurityGroupIndex		1.3.6.1.4.1.33.17.5.3.1.1
This variable identifies the group containing the security entry for which this entry contains information. The group ID may only be that of the target agent. Specifying a group ID of an agent in a different slot will result in `badValue` being returned.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterSecurityPortIndex		1.3.6.1.4.1.33.17.5.3.1.2
This variable identifies the port containing the security entry for which this entry contains infromation.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterSecurityAddress		1.3.6.1.4.1.33.17.5.3.1.3
This value will be compared to the destination address of all packets received on the port in applying the security action.
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

repeaterSecurityStatus		1.3.6.1.4.1.33.17.5.3.1.4
The status of the entry. Set to 'invalid' to remove the rule.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	invalid(1), valid(2)

repeaterSecurityAction		1.3.6.1.4.1.33.17.5.3.1.5
The action to take when the destination address matches.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	jam(1), allow(2)

repeaterSecurityGroupIndexShadow		1.3.6.1.4.1.33.17.5.4
This variable identifies the group containing a port to which a security address is to be assigned. The group ID may only be that of the target agent. Specifying a group ID of an agent in a different slot will result in `badValue` being returned.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

repeaterSecurityPortIndexShadow		1.3.6.1.4.1.33.17.5.5
This variable identifies the port of a group to which a security address is to be assigned.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

repeaterSecurityAddressShadow		1.3.6.1.4.1.33.17.5.6
This value contains the ethernet address which is to be added to the security address table for the port specified by repeaterSecurityGroupIndexShadow and repeaterSecurityPortIndexShadow.
Status: mandatory	Access: read-write
OBJECT-TYPE
	MacAddress

repeaterSecurityStatusShadow		1.3.6.1.4.1.33.17.5.7
When read, this variable will always return 'ready'. When this variable is set to 'execute' the address specified by repeaterSecurityAddressShadow will be added to the security address table for the port specified by repeaterSecurityGroupIndexShadow and repeaterSecurityPortIndexShadow. If any of the above variables are zero when this object is set to 'execute', 'bad value' will be returned.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ready(1), execute(2)

repeaterSecurityGlobalAddressTable		1.3.6.1.4.1.33.17.5.8
Table of ethernet addresses which are applied globally (intra Network 9000 chassis) to ports.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RepeaterSecurityGlobalAddressEntry

repeaterSecurityGlobalAddressEntry		1.3.6.1.4.1.33.17.5.8.1
An entry in the table containing information about a specific address.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	RepeaterSecurityGlobalAddressEntry

repeaterSecurityGlobalAddress		1.3.6.1.4.1.33.17.5.8.1.1
This variable identifies the address.
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

repeaterSecurityGlobalAddressStatus		1.3.6.1.4.1.33.17.5.8.1.2
This variable represents the status of the entry. Setting this object (or any other writable object) to 'valid' will cause the row in the table to be created. Setting this object to 'invalid' will cause the row to be removed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	invalid(1), valid(2)

repeaterSecurityGlobalAddressAction		1.3.6.1.4.1.33.17.5.8.1.3
This variable determines the action which is applied to the packet in the event of an address match. The packet is either passed untouched when set to 'pass', or it is forced to an alternating pattern of ones and zeros if set to 'jam'.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	jam(1), allow(2)

repeaterSecurityGlobalDBID		1.3.6.1.4.1.33.17.5.9
This variable contains the current version number of the global security database.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterSecurityGlobalSecurityAdminState		1.3.6.1.4.1.33.17.5.10
This variable controls whether global security is enabled or disabled. Global security will not function unless repeaterSecurityState and this variable are both set to `enabled`.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterSecurityGlobalSecurityOperState		1.3.6.1.4.1.33.17.5.11
This variable indicates the operational state of global security. If repeaterSecurityState is set to 'enabled' this variable will reflect the value of repeaterSecurityGlobalSecurityAdminState. if repeaterSecurityState is set to 'disabled', this variable will return 'securityDisabled'.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2), securityDisabled(3)

repeaterRepeaterTable		1.3.6.1.4.1.33.17.6.1
For repeaters that implement non-proxy management of logical repeaters, a table of descriptive and status information about a logical Ethernet repeater.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RepeaterRepeaterEntry

repeaterRepeaterEntry		1.3.6.1.4.1.33.17.6.1.1
An entry for a logical Ethernet repeater.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	RepeaterRepeaterEntry

repeaterRepeaterGroupIndex		1.3.6.1.4.1.33.17.6.1.1.1
The slot of the chassis.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterRepeaterIndex		1.3.6.1.4.1.33.17.6.1.1.2
The logical Ethernet repeater within the group.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterRepeaterSegment		1.3.6.1.4.1.33.17.6.1.1.3
The Network 9000 Ethernet network segment to which the logical repeater is attached.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Segment

repeaterRepeaterReports		1.3.6.1.4.1.33.17.6.1.1.4
Control for whether statistical reports will be collected for this logical repeater.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterRepeaterCollisions		1.3.6.1.4.1.33.17.6.1.1.5
The number of packet collisions detected on the Ethernet network segment to which this logical repeater is attached.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterRepeaterJabbers		1.3.6.1.4.1.33.17.6.1.1.6
The number of Jabber events detected for this logical repeater.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterRepeaterSQE		1.3.6.1.4.1.33.17.6.1.1.7
The number of SQE failure events detected for this logical repeater.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterRepeaterFifoOverflows		1.3.6.1.4.1.33.17.6.1.1.8
The number of times the report FIFO was full when this logical repeater attemped to write a packet report.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterRepeaterZero		1.3.6.1.4.1.33.17.6.1.1.9
Control for zeroing the logical repeater's counters. The agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting the value to 'execute' will zero the counters for the logical repeater.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ready(1), execute(2)

repeaterRepeaterSinceZero		1.3.6.1.4.1.33.17.6.1.1.10
The number of hundredths of a second since the counters for this logical repeater were last zeroed. This variable is set to zero when repeaterRepeaterZero is written with the value 'execute'.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

repeaterRepeaterSegmentsAllowed		1.3.6.1.4.1.33.17.6.1.1.11
The list of segments to which this repeater can be attached. The OCTET STRING contains a bitmap, with a bit for 'none' and one bit for each segment, and enough octets for all the Ethernet segments in the chassis. The high order bit of the first octet corresponds to 'none', the following bits correspond to the segments, in order, beginning with A.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

repeaterRepeaterTotalOctets		1.3.6.1.4.1.33.17.6.1.1.12
This variable will reflect the total number of bytes that the repeater both received from and sent to the segment. Bytes in both good and error frames are counted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterRepeaterTotalFrames		1.3.6.1.4.1.33.17.6.1.1.13
This variable will reflect the total number of frames that the repeater both received from and sent to the segment. Both good and error frames are counted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterRepeaterPercentUtilization		1.3.6.1.4.1.33.17.6.1.1.14
This variable will reflect the percentage of a full ethernet load that this repeater has handled since last zeroed. The value is calculated as `(8(totalBytes + (20*totalFrames)))/10 7(time)`.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

repeaterRedundancyState		1.3.6.1.4.1.33.17.7.1
This variable controls whether hub redundancy is enabled
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterRedundancyGroupTable		1.3.6.1.4.1.33.17.7.2
Table of descriptive and status information concerning hub redundancy groups.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RepeaterRedundancyGroupEntry

repeaterRedundancyGroupEntry		1.3.6.1.4.1.33.17.7.2.1
An entry in the table containing information about a specific hub redundancy group.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	RepeaterRedundancyGroupEntry

repeaterRedundancyGroupGroupIndex		1.3.6.1.4.1.33.17.7.2.1.1
This variable identifies the group.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterRedundancyGroupStatus		1.3.6.1.4.1.33.17.7.2.1.2
This variable represents the status of the entry. Setting this object (or any other writable object) to 'valid' will cause the row in the table to be created. Setting this object to 'invalid' will cause the row to be removed. If a row is removed from the group table, all related rows in the path table and address table are also removed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	invalid(1), valid(2)

repeaterRedundancyGroupName		1.3.6.1.4.1.33.17.7.2.1.3
This variable represents the definable name of the group. Prior to being set, this object will return the default name 'Groupn' where n is the value of repeaterRedundancyGroupIndex. Setting this object to a zero length string will cause the default name to be assumed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..16)

repeaterRedundancyGroupAdminState		1.3.6.1.4.1.33.17.7.2.1.4
This variable represents the desired state of the group. When this variable is set to 'enabled', the group will be activly monitored for integrity, and back- up paths will be brought up as higher priority paths disappear. When set to 'disabled', the path will not be tested for integrity.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterRedundancyGroupTestInterval		1.3.6.1.4.1.33.17.7.2.1.5
This variable determines the rate at which testing is performed on the path which is currently active (repeaterRedundancyGroupOperPath) in order to determine integrity. The value is in milliseconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	250..180000

repeaterRedundancyGroupRollbackAdminState		1.3.6.1.4.1.33.17.7.2.1.6
This variable represents the desired state of path rollback. Path rollback is defined as the automatic testing and reactivation of higher priority paths. It should be noted that in order to test higher priority paths, the currently enabled path will be interrupted. Setting this variable to 'enabled' will cause rollback testing to occur every repeaterRedundancyGroupRollbackInterval number of milliseconds. Setting this variable to 'disabled' will force the group to remain on lower priority paths, until they themselves fail.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterRedundancyGroupRollbackInterval		1.3.6.1.4.1.33.17.7.2.1.7
This variable determines the rate at which rollback testing is performed. The value is in milliseconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	500..180000

repeaterRedundancyGroupOperPath		1.3.6.1.4.1.33.17.7.2.1.8
This variable represents the index of the path which is currently being used as the active path. This value may be used as the value for repeaterRedundancyPathIndex to index the path table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterRedundancyGroupPathChanges		1.3.6.1.4.1.33.17.7.2.1.9
The value of this variable represents the number of times that this group has changed paths.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterRedundancyGroupRollbackAttempts		1.3.6.1.4.1.33.17.7.2.1.10
The value of this variable represents the number of times that the current path has been interrupted in interest of testing a higher priority path.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterRedundancyGroupZero		1.3.6.1.4.1.33.17.7.2.1.11
This variable is used to zero all counters associated with a group. This variable when read will always read 'ready'. When set to 'execute', all counters associated with the group (group counters and path counters) will be set to zero.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ready(1), execute(2)

repeaterRedundancyGroupSinceZero		1.3.6.1.4.1.33.17.7.2.1.12
The value of this variable represents the number of seconds which have elapsed since the counters associated with the group have been zeroed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

repeaterRedundancyGroupConfigStatus		1.3.6.1.4.1.33.17.7.2.1.13
In order for a particular redundancy group to be used by the system, it must have at least one redundancy path defined. This variable indicates whether a redundancy group has been completely configured, and can therefore become active.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	incomplete(1), complete(2)

repeaterRedundancyPathTable		1.3.6.1.4.1.33.17.7.3
Table of descriptive and status information concerning hub redundancy paths.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RepeaterRedundancyPathEntry

repeaterRedundancyPathEntry		1.3.6.1.4.1.33.17.7.3.1
An entry in the table containing information about a specific hub redundancy path.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	RepeaterRedundancyPathEntry

repeaterRedundancyPathGroupIndex		1.3.6.1.4.1.33.17.7.3.1.1
This variable identifies the group.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterRedundancyPathPathIndex		1.3.6.1.4.1.33.17.7.3.1.2
This variable identifies the path of the group.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterRedundancyPathStatus		1.3.6.1.4.1.33.17.7.3.1.3
This variable represents the status of the entry. Setting this object (or any other writable object) to 'valid' will cause the row in the table to be created. Setting this object to 'invalid' will cause the row to be removed. If a row is removed from the path table, all related rows in the address table are also removed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	invalid(1), valid(2)

repeaterRedundancyPathSlot		1.3.6.1.4.1.33.17.7.3.1.4
This variable represents the slot of the Network 9000 chassis which contains the repeater on which the path interface resides.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

repeaterRedundancyPathPort		1.3.6.1.4.1.33.17.7.3.1.5
This variable represents the port of the repeater to which the path is connected.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

repeaterRedundancyPathPriority		1.3.6.1.4.1.33.17.7.3.1.6
This variable represents the order of preferred priority for the path. Lower numbed paths are preferred over higher numbered paths.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

repeaterRedundancyPathActivate		1.3.6.1.4.1.33.17.7.3.1.7
This variable is used to immediately make a specific path active. This variable when read will always read 'ready'. When set to 'execute', the selected path will become the active path for the group. Note that if rollback is enabled and this path is lower in priority, the system will attempt to restore the higher priority path.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ready(1), execute(2)

repeaterRedundancyPathTimeout		1.3.6.1.4.1.33.17.7.3.1.8
This variable represents the amount of time in milliseconds that the syatem will wait for test responses from targets on the path.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	250..10000

repeaterRedundancyPathRetryCount		1.3.6.1.4.1.33.17.7.3.1.9
This variable represents the number of times a test is retried on the path in the event of a timeout before the path is considered useless.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..50

repeaterRedundancyPathTestAttempts		1.3.6.1.4.1.33.17.7.3.1.10
The value of this variable represents the number of times that an integrity test was performed on the path.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterRedundancyPathLastTestStatus		1.3.6.1.4.1.33.17.7.3.1.11
This variable indicates the result of the last test of the path. 'notTested' indicates that the path has yet to be tested. 'responded' indicates that a target on the path path has responded to the last test, 'timeout' indicates that no target on the path responded to the last test. 'integrity' indicates that a test was not performed on the path due to an abscense of port integrity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notTested(1), responded(2), timeout(3), noIntegrity(4)

repeaterRedundancyPathDisposition		1.3.6.1.4.1.33.17.7.3.1.12
This variable controls the action that will be taken when a path is considered bad. 'disable' indicates that the path is to be disabled prior to switching to an alternate path. 'null' indicates that the failed path is to be left in its current state prior to switching to an alternate path.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), null(2)

repeaterRedundancyPathConfigStatus		1.3.6.1.4.1.33.17.7.3.1.13
In order for a particular redundancy path to be used by the system, it must have at least one target address and the slot and the port on which it originates defined. This variable indicates whether a redundancy path has been completely configured, and can therefore become active.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	incomplete(1), complete(2)

repeaterRedundancyPathAdminState		1.3.6.1.4.1.33.17.7.3.1.14
This variable represents the desired state of the path. When this variable is set to 'disabled' the path will not be used by the group. When set to 'enabled', the path is available as an alternate or primary path.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

repeaterRedundancyAddressTable		1.3.6.1.4.1.33.17.7.4
Table of descriptive and status information concerning hub redundancy target addresses.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RepeaterRedundancyAddressEntry

repeaterRedundancyAddressEntry		1.3.6.1.4.1.33.17.7.4.1
An entry in the table containing information about a specific target address associated with a hub redundancy path.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	RepeaterRedundancyAddressEntry

repeaterRedundancyAddressGroupIndex		1.3.6.1.4.1.33.17.7.4.1.1
This variable identifies the group.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterRedundancyAddressPathIndex		1.3.6.1.4.1.33.17.7.4.1.2
This variable identifies the path of the group.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

repeaterRedundancyAddressAddress		1.3.6.1.4.1.33.17.7.4.1.3
This variable identifies the specific target address.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TypedAddress

repeaterRedundancyAddressStatus		1.3.6.1.4.1.33.17.7.4.1.4
This variable represents the status of the entry. Setting this object (or any other writable object) to 'valid' will cause the row in the table to be created. Setting this object to 'invalid' will cause the row to be removed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	invalid(1), valid(2)

repeaterRedundancyAddressResponses		1.3.6.1.4.1.33.17.7.4.1.5
This value of this variable represents the number of times this specific address has responded to a test attempt.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

repeaterRedundancyAddressLastTestStatus		1.3.6.1.4.1.33.17.7.4.1.6
This variable indicates whether this particular address responded to the last test of the path. 'notTested' indicates that the path has yet to be tested. 'responded' indicates that the target responded to the last test, 'timeout' indicates that the target responded to the last test.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notTested(1), responded(2), timeout(3)

accessViolation		1
Access violation by connected system with Ethernet address not allowed by repeaterPortAccessTable and repeaterPortAccessAction.
TRAP-TYPE

integrityLoss		2
This port has lost link integrity.
TRAP-TYPE

redundancyPathChange		3
This trap issued to indicate that a redundancy group has experienced a path change. The offending group and the new path are included in the trap.
TRAP-TYPE