Juniper-BGP-MIB

File: Juniper-BGP-MIB.mib (420073 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
Juniper-MIBs Juniper-TC

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
IpAddress Integer32 Counter32
Gauge32 DisplayString TruthValue
RowStatus TEXTUAL-CONVENTION MODULE-COMPLIANCE
OBJECT-GROUP juniMibs JuniVrfName

Defined Types

JuniBgpAfi  
Address family identifier (AFI).
TEXTUAL-CONVENTION    
  INTEGER bgpIpV4(1), bgpIpV6(2)  

JuniBgpSafi  
Subsequent address family identifier (SAFI).
TEXTUAL-CONVENTION    
  INTEGER bgpUnicast(1), bgpMulticast(2), bgpUnicastMulticast(3), bgpVPNUnicast(128)  

JuniBgpStorageInteger  
Specifies an unsigned integer. If an object with this type is set while BGP is created, the value will not be used until a reboot occurs.
TEXTUAL-CONVENTION    
  Unsigned32  

JuniBgpResetConnectionType  
Writing a value to an object of this type will cause the corresponding reset action to take place: resetTypeNoop - no action (this value is always returned on a read) resetTypeHard - causes a BGP session to be dropped and then re-established resetTypeSoftIn - causes inbound policy to be re-applied to received routes resetTypeSoftOut - causes outbound policy to be re-applied to sent routes resetTypeSoftInOut - does both resetTypeSoftIn and resetTypeSoftOut resetTypeRouteFlapHistory - causes route-flap dampening history to be discarded resetTypeSoftInWithPrefixOrfPush - causes BGP to push out prefix-list ORF and perform inbound soft reconfiguration resetTypeWaitEndOfRib - causes BGP to stop waiting for the End-of-RIB flag from the peer(s) resetTypeRecreateAllIpDynInterfaces - causes all dynamically created IP interfaces to be recreated resetTypeDynamicPeers - causes dynamically create peers to be removed
TEXTUAL-CONVENTION    
  INTEGER resetTypeNoop(0), resetTypeHard(1), resetTypeSoftIn(2), resetTypeSoftOut(3), resetTypeSoftInOut(4), resetTypeRouteFlapHistory(5), resetTypeSoftInWithPrefixOrfPush(6), resetTypeWaitEndOfRib(7), resetTypeRecreateAllIpDynInterfaces(8), resetTypeDynamicPeers(9)  

JuniBgpFourOctetAsNumber  
Four-octet AS-number.
TEXTUAL-CONVENTION    
  Unsigned32  

JuniBgpAdvertiseMapName  
Advertise route-map name. Represents textual information taken from the NVT ASCII character set.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..32)  

JuniBgpConditionalAdvStatus  
BGP Conditional Advertisement Status
TEXTUAL-CONVENTION    
  INTEGER advertise(1), withdraw(2)  

JuniBgpConfederationPeerEntry  
SEQUENCE    
  juniBgpConfederationPeerAsNumber Integer32
  juniBgpConfederationPeerRowStatus RowStatus

JuniBgpFourOctetConfederationPeerEntry  
SEQUENCE    
  juniBgpFourOctetConfederationPeerAsNumber JuniBgpFourOctetAsNumber
  juniBgpFourOctetConfederationPeerRowStatus RowStatus

JuniBgpPeerEntry  
SEQUENCE    
  juniBgpPeerVrfName JuniVrfName
  juniBgpPeerRemoteAddress IpAddress
  juniBgpPeerAdminStatus INTEGER
  juniBgpPeerState INTEGER
  juniBgpPeerNegotiatedVersion Integer32
  juniBgpPeerLocalAddress IpAddress
  juniBgpPeerLocalAddressMask IpAddress
  juniBgpPeerLocalPort Integer32
  juniBgpPeerRemoteAsNumber Integer32
  juniBgpPeerRemotePort Integer32
  juniBgpPeerInUpdates Counter32
  juniBgpPeerOutUpdates Counter32
  juniBgpPeerInTotalMessages Counter32
  juniBgpPeerOutTotalMessages Counter32
  juniBgpPeerLastErrorCode OCTET STRING
  juniBgpPeerLastResetReason DisplayString
  juniBgpPeerFsmEstablishedTransitions Counter32
  juniBgpPeerFsmEstablishedTime Gauge32
  juniBgpPeerRetryInterval Integer32
  juniBgpPeerHoldTime Integer32
  juniBgpPeerKeepAliveInterval Integer32
  juniBgpPeerConfigHoldTime Integer32
  juniBgpPeerConfigKeepAliveInterval Integer32
  juniBgpPeerAsOriginationInterval Integer32
  juniBgpPeerAdvertisementInterval Integer32
  juniBgpPeerInUpdateElapsedTime Gauge32
  juniBgpPeerDescription DisplayString
  juniBgpPeerRemoteIdentifier IpAddress
  juniBgpPeerWeight Unsigned32
  juniBgpPeerEbgpMultihop TruthValue
  juniBgpPeerEbgpMultihopTtl Integer32
  juniBgpPeerUpdateSource IpAddress
  juniBgpPeerMd5Password OCTET STRING
  juniBgpPeerMaxUpdateSize Unsigned32
  juniBgpPeerType INTEGER
  juniBgpPeerReceivedCapabilitiesOption TruthValue
  juniBgpPeerReceivedCapabilityMultiProtocol TruthValue
  juniBgpPeerReceivedCapabilityRouteRefresh TruthValue
  juniBgpPeerReceivedCapabilityRouteRefreshCisco TruthValue
  juniBgpPeerResetConnectionType JuniBgpResetConnectionType
  juniBgpPeerRowStatus RowStatus
  juniBgpPeerLocalAsNumber Integer32
  juniBgpPeerFourOctetRemoteAsNumber JuniBgpFourOctetAsNumber
  juniBgpPeerFourOctetLocalAsNumber JuniBgpFourOctetAsNumber
  juniBgpPeerReceivedCapabilityFourOctetAsNumbers TruthValue
  juniBgpPeerReceivedCapabilityDynamicCapabilityNeg TruthValue
  juniBgpPeerShouldAdvertiseCapabilitiesOption TruthValue
  juniBgpPeerShouldAdvertiseCapabilityRouteRefresh TruthValue
  juniBgpPeerShouldAdvertiseCapabilityRouteRefreshCisco TruthValue
  juniBgpPeerShouldAdvertiseCapabilityFourOctetAsNumbers TruthValue
  juniBgpPeerShouldAdvertiseCapabilityDynamicCapabilityNeg TruthValue
  juniBgpPeerSentCapabilitiesOption TruthValue
  juniBgpPeerSentCapabilityMultiProtocol TruthValue
  juniBgpPeerSentCapabilityRouteRefresh TruthValue
  juniBgpPeerSentCapabilityRouteRefreshCisco TruthValue
  juniBgpPeerSentCapabilityFourOctetAsNumbers TruthValue
  juniBgpPeerSentCapabilityDynamicCapabilityNeg TruthValue
  juniBgpPeerReceivedUnsupportedOptionalParameterNotification TruthValue
  juniBgpPeerReceivedUnsupportedCapabilityNotification TruthValue
  juniBgpPeerUnconfiguredAttributes BITS
  juniBgpPeerSiteOfOrigin OCTET STRING
  juniBgpPeerLenient TruthValue
  juniBgpPeerReceivedCapabilityOldDynamicCapabilityNeg TruthValue
  juniBgpPeerShouldAdvertiseCapabilityOldDynamicCapabilityNeg TruthValue
  juniBgpPeerSentCapabilityOldDynamicCapabilityNeg TruthValue
  juniBgpPeerPassive TruthValue
  juniBgpPeerDynamic TruthValue
  juniBgpPeerShouldAdvertiseCapabilityGracefulRestart TruthValue
  juniBgpPeerSentCapabilityGracefulRestart TruthValue
  juniBgpPeerReceivedCapabilityGracefulRestart TruthValue
  juniBgpPeerGracefulRestartRestartTime Integer32
  juniBgpPeerGracefulRestartStalePathsTime Integer32
  juniBgpPeerSentGracefulRestartRestartState TruthValue
  juniBgpPeerReceivedGracefulRestartRestartState TruthValue
  juniBgpPeerSentGracefulRestartRestartTime Integer32
  juniBgpPeerReceivedGracefulRestartRestartTime Integer32
  juniBgpPeerTimeUntilGracefulRestartRestartTimerExpires Integer32
  juniBgpPeerTimeUntilGracefulRestartStalePathsTimerExpires Integer32
  juniBgpPeerBfdEnabled TruthValue
  juniBgpPeerBfdMinTransmitInterval Integer32
  juniBgpPeerBfdMinReceiveInterval Integer32
  juniBgpPeerBfdMultiplier Integer32
  juniBgpPeerBfdSessionUp TruthValue
  juniBgpPeerBfdDetectionTime Integer32
  juniBgpPeerIbgpSinglehop TruthValue

JuniBgpPeerProposedAfiSafiPeerEntry  
SEQUENCE    
  juniBgpPeerProposedAfiSafiPeerVrfName JuniVrfName
  juniBgpPeerProposedAfiSafiPeerRemoteAddr IpAddress
  juniBgpPeerProposedAfiSafiPeerAfi JuniBgpAfi
  juniBgpPeerProposedAfiSafiPeerSafi JuniBgpSafi
  juniBgpPeerProposedAfiSafiPeerRowStatus RowStatus

JuniBgpLocalProposedAfiSafiPeerEntry  
SEQUENCE    
  juniBgpLocalProposedAfiSafiPeerVrfName JuniVrfName
  juniBgpLocalProposedAfiSafiPeerRemoteAddr IpAddress
  juniBgpLocalProposedAfiSafiPeerAfi JuniBgpAfi
  juniBgpLocalProposedAfiSafiPeerSafi JuniBgpSafi
  juniBgpLocalProposedAfiSafiPeerRowStatus RowStatus

JuniBgpExchangedAfiSafiPeerEntry  
SEQUENCE    
  juniBgpExchangedAfiSafiPeerVrfName JuniVrfName
  juniBgpExchangedAfiSafiPeerRemoteAddr IpAddress
  juniBgpExchangedAfiSafiPeerAfi JuniBgpAfi
  juniBgpExchangedAfiSafiPeerSafi JuniBgpSafi
  juniBgpExchangedAfiSafiPeerRowStatus RowStatus

JuniBgpPeerDynamicCapabilityEntry  
SEQUENCE    
  juniBgpPeerDynamicCapabilityPeerVrfName JuniVrfName
  juniBgpPeerDynamicCapabilityPeerRemoteAddr IpAddress
  juniBgpPeerDynamicCapabilityCode Integer32
  juniBgpPeerDynamicCapabilitySent TruthValue
  juniBgpPeerDynamicCapabilityReceived TruthValue

JuniBgpPeerAddressFamilyEntry  
SEQUENCE    
  juniBgpPeerAddressFamilyVrfName JuniVrfName
  juniBgpPeerAddressFamilyAfi JuniBgpAfi
  juniBgpPeerAddressFamilySafi JuniBgpSafi
  juniBgpPeerAddressFamilyRemoteAddress IpAddress
  juniBgpPeerAddressFamilyPeerGroup DisplayString
  juniBgpPeerAddressFamilyDefaultOriginate TruthValue
  juniBgpPeerAddressFamilyNextHopSelf TruthValue
  juniBgpPeerAddressFamilyNextHopUnchanged TruthValue
  juniBgpPeerAddressFamilySendCommunity TruthValue
  juniBgpPeerAddressFamilyDistributeListIn DisplayString
  juniBgpPeerAddressFamilyDistributeListOut DisplayString
  juniBgpPeerAddressFamilyPrefixListIn DisplayString
  juniBgpPeerAddressFamilyPrefixListOut DisplayString
  juniBgpPeerAddressFamilyPrefixTreeIn DisplayString
  juniBgpPeerAddressFamilyPrefixTreeOut DisplayString
  juniBgpPeerAddressFamilyFilterListIn DisplayString
  juniBgpPeerAddressFamilyFilterListOut DisplayString
  juniBgpPeerAddressFamilyFilterListWeight DisplayString
  juniBgpPeerAddressFamilyFilterListWeightValue Unsigned32
  juniBgpPeerAddressFamilyRouteMapIn DisplayString
  juniBgpPeerAddressFamilyRouteMapOut DisplayString
  juniBgpPeerAddressFamilyRouteReflectorClient TruthValue
  juniBgpPeerAddressFamilyRouteLimitWarn Unsigned32
  juniBgpPeerAddressFamilyRouteLimitReset Unsigned32
  juniBgpPeerAddressFamilyRouteLimitWarnOnly TruthValue
  juniBgpPeerAddressFamilyRemovePrivateAs TruthValue
  juniBgpPeerAddressFamilyUnsuppressMap DisplayString
  juniBgpPeerAddressFamilyInboundSoftReconfig TruthValue
  juniBgpPeerAddressFamilyResetConnectionType JuniBgpResetConnectionType
  juniBgpPeerAddressFamilyRowStatus RowStatus
  juniBgpPeerAddressFamilyAsOverride TruthValue
  juniBgpPeerAddressFamilyAllowAsIn Integer32
  juniBgpPeerAddressFamilySendExtendedCommunity TruthValue
  juniBgpPeerAddressFamilyAdvertiseCapPrefixListOrfSend TruthValue
  juniBgpPeerAddressFamilyAdvertiseCapPrefixListOrfReceive TruthValue
  juniBgpPeerAddressFamilyAdvertiseCapPrefixListCiscoOrfSend TruthValue
  juniBgpPeerAddressFamilyAdvertiseCapPrefixListCiscoOrfReceive TruthValue
  juniBgpPeerAddressFamilyReceivedCapPrefixListOrfSend TruthValue
  juniBgpPeerAddressFamilyReceivedCapPrefixListOrfReceive TruthValue
  juniBgpPeerAddressFamilyReceivedCapPrefixListCiscoOrfSend TruthValue
  juniBgpPeerAddressFamilyReceivedCapPrefixListCiscoOrfReceive TruthValue
  juniBgpPeerAddressFamilyReceivedOrfEntriesLimit Unsigned32
  juniBgpPeerAddressFamilyReceivedPrefixListOrfName DisplayString
  juniBgpPeerAddressFamilyMaximumPrefixStrict TruthValue
  juniBgpPeerAddressFamilyUnconfiguredAttributes BITS
  juniBgpPeerAddressFamilySendLabel TruthValue
  juniBgpPeerAddressFamilyDefaultOriginateRouteMap DisplayString
  juniBgpPeerAddressFamilySentCapabilityGracefulRestart TruthValue
  juniBgpPeerAddressFamilyReceivedCapabilityGracefulRestart TruthValue
  juniBgpPeerAddressFamilySentForwardingStatePreserved TruthValue
  juniBgpPeerAddressFamilyReceivedForwardingStatePreserved TruthValue
  juniBgpPeerAddressFamilySentEndOfRibMarker TruthValue
  juniBgpPeerAddressFamilyReceivedEndOfRibMarker TruthValue
  juniBgpPeerAddressFamilyWaitingForEndOfRibBeforeFlushStaleRoutes TruthValue
  juniBgpPeerAddressFamilyWaitingForEndOfRibBeforePathSelection TruthValue

JuniBgpPeerAddressFamilyConditionalAdvEntry  
SEQUENCE    
  juniBgpPeerAddressFamilyConditionalAdvAdvertiseMap JuniBgpAdvertiseMapName
  juniBgpPeerAddressFamilyConditionalAdvConditionMap DisplayString
  juniBgpPeerAddressFamilyConditionalAdvIsExistMap TruthValue
  juniBgpPeerAddressFamilyConditionalAdvSequenceNum Integer32
  juniBgpPeerAddressFamilyConditionalAdvStatus JuniBgpConditionalAdvStatus
  juniBgpPeerAddressFamilyConditionalAdvRowStatus RowStatus

JuniBgpPeerGroupEntry  
SEQUENCE    
  juniBgpPeerGroupVrfName JuniVrfName
  juniBgpPeerGroupGroupName DisplayString
  juniBgpPeerGroupAdminStatus INTEGER
  juniBgpPeerGroupRemoteAsNumber Integer32
  juniBgpPeerGroupRetryInterval Integer32
  juniBgpPeerGroupConfigHoldTime Integer32
  juniBgpPeerGroupConfigKeepAliveInterval Integer32
  juniBgpPeerGroupAsOriginationInterval Integer32
  juniBgpPeerGroupAdvertisementInterval Integer32
  juniBgpPeerGroupDescription DisplayString
  juniBgpPeerGroupWeight Unsigned32
  juniBgpPeerGroupEbgpMultihop TruthValue
  juniBgpPeerGroupEbgpMultihopTtl Integer32
  juniBgpPeerGroupUpdateSource IpAddress
  juniBgpPeerGroupMd5Password OCTET STRING
  juniBgpPeerGroupMaxUpdateSize Unsigned32
  juniBgpPeerGroupResetConnectionType JuniBgpResetConnectionType
  juniBgpPeerGroupRowStatus RowStatus
  juniBgpPeerGroupLocalAsNumber Integer32
  juniBgpPeerGroupFourOctetRemoteAsNumber JuniBgpFourOctetAsNumber
  juniBgpPeerGroupFourOctetLocalAsNumber JuniBgpFourOctetAsNumber
  juniBgpPeerGroupShouldAdvertiseCapabilitiesOption TruthValue
  juniBgpPeerGroupShouldAdvertiseCapabilityRouteRefresh TruthValue
  juniBgpPeerGroupShouldAdvertiseCapabilityRouteRefreshCisco TruthValue
  juniBgpPeerGroupShouldAdvertiseCapabilityFourOctetAsNumbers TruthValue
  juniBgpPeerGroupShouldAdvertiseCapabilityDynamicCapabilityNeg TruthValue
  juniBgpPeerGroupUnconfiguredAttributes BITS
  juniBgpPeerGroupSiteOfOrigin OCTET STRING
  juniBgpPeerGroupLenient TruthValue
  juniBgpPeerGroupShouldAdvertiseCapabilityOldDynamicCapabilityNeg TruthValue
  juniBgpPeerGroupPassive TruthValue
  juniBgpPeerGroupConfiguredPeerType INTEGER
  juniBgpPeerGroupAllowAccessListName DisplayString
  juniBgpPeerGroupAllowMaxPeers Unsigned32
  juniBgpPeerGroupCurrentDynamicPeerCount Unsigned32
  juniBgpPeerGroupHighWaterMarkDynamicPeerCount Unsigned32
  juniBgpPeerGroupRejectedDynamicPeerCount Unsigned32
  juniBgpPeerGroupShouldAdvertiseCapabilityGracefulRestart TruthValue
  juniBgpPeerGroupGracefulRestartRestartTime Integer32
  juniBgpPeerGroupGracefulRestartStalePathsTime Integer32
  juniBgpPeerGroupBfdEnabled TruthValue
  juniBgpPeerGroupBfdMinTransmitInterval Integer32
  juniBgpPeerGroupBfdMinReceiveInterval Integer32
  juniBgpPeerGroupBfdMultiplier Integer32
  juniBgpPeerGroupIbgpSinglehop TruthValue

JuniBgpPeerGroupAddressFamilyEntry  
SEQUENCE    
  juniBgpPeerGroupAddressFamilyVrfName JuniVrfName
  juniBgpPeerGroupAddressFamilyAfi JuniBgpAfi
  juniBgpPeerGroupAddressFamilySafi JuniBgpSafi
  juniBgpPeerGroupGroupAddressFamilyGroupName DisplayString
  juniBgpPeerGroupAddressFamilyDefaultOriginate TruthValue
  juniBgpPeerGroupAddressFamilyNextHopSelf TruthValue
  juniBgpPeerGroupAddressFamilyNextHopUnchanged TruthValue
  juniBgpPeerGroupAddressFamilySendCommunity TruthValue
  juniBgpPeerGroupAddressFamilyDistributeListIn DisplayString
  juniBgpPeerGroupAddressFamilyDistributeListOut DisplayString
  juniBgpPeerGroupAddressFamilyPrefixListIn DisplayString
  juniBgpPeerGroupAddressFamilyPrefixListOut DisplayString
  juniBgpPeerGroupAddressFamilyPrefixTreeIn DisplayString
  juniBgpPeerGroupAddressFamilyPrefixTreeOut DisplayString
  juniBgpPeerGroupAddressFamilyFilterListIn DisplayString
  juniBgpPeerGroupAddressFamilyFilterListOut DisplayString
  juniBgpPeerGroupAddressFamilyFilterListWeight DisplayString
  juniBgpPeerGroupAddressFamilyFilterListWeightValue Unsigned32
  juniBgpPeerGroupAddressFamilyRouteMapIn DisplayString
  juniBgpPeerGroupAddressFamilyRouteMapOut DisplayString
  juniBgpPeerGroupAddressFamilyRouteReflectorClient TruthValue
  juniBgpPeerGroupAddressFamilyRouteLimitWarn Unsigned32
  juniBgpPeerGroupAddressFamilyRouteLimitReset Unsigned32
  juniBgpPeerGroupAddressFamilyRouteLimitWarnOnly TruthValue
  juniBgpPeerGroupAddressFamilyRemovePrivateAs TruthValue
  juniBgpPeerGroupAddressFamilyUnsuppressMap DisplayString
  juniBgpPeerGroupAddressFamilyInboundSoftReconfig TruthValue
  juniBgpPeerGroupAddressFamilyResetConnectionType JuniBgpResetConnectionType
  juniBgpPeerGroupAddressFamilyRowStatus RowStatus
  juniBgpPeerGroupAddressFamilyAsOverride TruthValue
  juniBgpPeerGroupAddressFamilyAllowAsIn Integer32
  juniBgpPeerGroupAddressFamilySendExtendedCommunity TruthValue
  juniBgpPeerGroupAddressFamilyAdvertiseCapPrefixListOrfSend TruthValue
  juniBgpPeerGroupAddressFamilyAdvertiseCapPrefixListCiscoOrfSend TruthValue
  juniBgpPeerGroupAddressFamilyMaximumPrefixStrict TruthValue
  juniBgpPeerGroupAddressFamilyUnconfiguredAttributes BITS
  juniBgpPeerGroupAddressFamilySendLabel TruthValue
  juniBgpPeerGroupAddressFamilyDefaultOriginateRouteMap DisplayString

JuniBgpPeerGroupAddressFamilyConditionalAdvEntry  
SEQUENCE    
  juniBgpPeerGroupAddressFamilyConditionalAdvAdvertiseMap JuniBgpAdvertiseMapName
  juniBgpPeerGroupAddressFamilyConditionalAdvConditionMap DisplayString
  juniBgpPeerGroupAddressFamilyConditionalAdvIsExistMap TruthValue
  juniBgpPeerGroupAddressFamilyConditionalAdvSequenceNum Integer32
  juniBgpPeerGroupAddressFamilyConditionalAdvStatus JuniBgpConditionalAdvStatus
  juniBgpPeerGroupAddressFamilyConditionalAdvRowStatus RowStatus

JuniBgpNetworkEntry  
SEQUENCE    
  juniBgpNetworkVrfName JuniVrfName
  juniBgpNetworkAfi JuniBgpAfi
  juniBgpNetworkSafi JuniBgpSafi
  juniBgpNetworkIpAddrPrefix IpAddress
  juniBgpNetworkIpAddrPrefixLen Integer32
  juniBgpNetworkBackdoor TruthValue
  juniBgpNetworkRowStatus RowStatus
  juniBgpNetworkWeightSpecified TruthValue
  juniBgpNetworkWeight Integer32
  juniBgpNetworkRouteMap DisplayString
  juniBgpNetworkUnconfiguredAttributes BITS

JuniBgpAggregateEntry  
SEQUENCE    
  juniBgpAggregateVrfName JuniVrfName
  juniBgpAggregateAfi JuniBgpAfi
  juniBgpAggregateSafi JuniBgpSafi
  juniBgpAggregateIpAddrPrefix IpAddress
  juniBgpAggregateIpAddrPrefixLen Integer32
  juniBgpAggregateAsSet TruthValue
  juniBgpAggregateSummaryOnly TruthValue
  juniBgpAggregateAttributeMap DisplayString
  juniBgpAggregateAdvertiseMap DisplayString
  juniBgpAggregateRowStatus RowStatus
  juniBgpAggregateSuppressMap DisplayString
  juniBgpAggregateUnconfiguredAttributes BITS

JuniBgpVrfEntry  
SEQUENCE    
  juniBgpVrfName JuniVrfName
  juniBgpVrfSynchronization TruthValue
  juniBgpVrfAutoSummary TruthValue
  juniBgpVrfExternalDistance Integer32
  juniBgpVrfInternalDistance Integer32
  juniBgpVrfLocalDistance Integer32
  juniBgpVrfResetConnectionType JuniBgpResetConnectionType
  juniBgpVrfRowStatus RowStatus
  juniBgpVrfOperationalState INTEGER
  juniBgpVrfAddUnicastRoutesToMulticastView TruthValue
  juniBgpVrfMaximumPathsEbgp Integer32
  juniBgpVrfMaximumPathsIbgp Integer32
  juniBgpVrfUnconfiguredAttributes BITS
  juniBgpVrfMaximumPathsEIbgp Integer32
  juniBgpVrfCarriersCarrierModeEnabled TruthValue

JuniBgpAddressFamilyEntry  
SEQUENCE    
  juniBgpAddressFamilyVrfName JuniVrfName
  juniBgpAddressFamilyAfi JuniBgpAfi
  juniBgpAddressFamilySafi JuniBgpSafi
  juniBgpAddressFamilyDefaultOriginate TruthValue
  juniBgpAddressFamilyRouteFlapDampening TruthValue
  juniBgpAddressFamilyDampeningSuppressThreshold Unsigned32
  juniBgpAddressFamilyDampeningReuseThreshold Unsigned32
  juniBgpAddressFamilyDampeningMaxHoldDownTime Unsigned32
  juniBgpAddressFamilyDampeningHalfLifeReachable Unsigned32
  juniBgpAddressFamilyDampeningHalfLifeUnreachable Unsigned32
  juniBgpAddressFamilyDampeningRouteMapName DisplayString
  juniBgpAddressFamilyResetConnectionType JuniBgpResetConnectionType
  juniBgpAddressFamilyRowStatus RowStatus
  juniBgpAddressFamilyOperationalState INTEGER
  juniBgpAddressFamilyUnconfiguredAttributes BITS
  juniBgpAddressFamilyExternalDistance Integer32
  juniBgpAddressFamilyInternalDistance Integer32
  juniBgpAddressFamilyLocalDistance Integer32
  juniBgpAddressFamilyDefaultOriginateRouteMap DisplayString
  juniBgpAddressFamilyIpIntfProfileNameForMplsHeads DisplayString
  juniBgpAddressFamilyIpIntfProfileNameForMplsTails DisplayString
  juniBgpAddressFamilyIpIntfServiceProfileNameForMplsHeads DisplayString
  juniBgpAddressFamilyIpIntfServiceProfileNameForMplsTails DisplayString
  juniBgpAddressFamilyCheckVpnNextHops TruthValue
  juniBgpAddressFamilyPathSelectionIsDeferred TruthValue
  juniBgpAddressFamilyPreventBgpRoutesFromBeingPushedToLineCards TruthValue
  juniBgpAddressFamilyTimeUntilPathSelectionDeferTimerExpires Integer32

JuniBgpNewRouteEntry  
SEQUENCE    
  juniBgpNewRouteVrfName JuniVrfName
  juniBgpNewRouteAfi JuniBgpAfi
  juniBgpNewRouteSafi JuniBgpSafi
  juniBgpNewRouteIpAddrPrefix IpAddress
  juniBgpNewRouteIpAddrPrefixLen Integer32
  juniBgpNewRouteDistinguisher OCTET STRING
  juniBgpNewRoutePeer IpAddress
  juniBgpNewRouteRouteType INTEGER
  juniBgpNewRouteOriginalRd OCTET STRING
  juniBgpNewRouteOriginatorId IpAddress
  juniBgpNewRouteAtomicAggregatePresent TruthValue
  juniBgpNewRouteMedPresent TruthValue
  juniBgpNewRouteLocalPrefPresent TruthValue
  juniBgpNewRouteAggregatorPresent TruthValue
  juniBgpNewRouteCommunitiesPresent TruthValue
  juniBgpNewRouteOriginatorIdPresent TruthValue
  juniBgpNewRouteClusterListPresent TruthValue
  juniBgpNewRouteWeight Unsigned32
  juniBgpNewRouteOrigin INTEGER
  juniBgpNewRouteASPathSegment OCTET STRING
  juniBgpNewRouteNextHop IpAddress
  juniBgpNewRouteMultiExitDisc Unsigned32
  juniBgpNewRouteLocalPref Unsigned32
  juniBgpNewRouteAtomicAggregate INTEGER
  juniBgpNewRouteAggregatorAS Integer32
  juniBgpNewRouteAggregatorAddress IpAddress
  juniBgpNewRouteBestInIpRouteTable TruthValue
  juniBgpNewRouteUnknown OCTET STRING
  juniBgpNewRouteExtendedCommunitiesPresent TruthValue
  juniBgpNewRouteValid TruthValue
  juniBgpNewRouteSuppressedBy INTEGER
  juniBgpNewRouteNextHopReachable TruthValue
  juniBgpNewRouteSynchronizedWithIgp TruthValue
  juniBgpNewRoutePlaceInIpRouteTable TruthValue
  juniBgpNewRouteAdvertiseToExternalPeers TruthValue
  juniBgpNewRouteAdvertiseToInternalPeers TruthValue
  juniBgpNewRouteMplsLabel Unsigned32
  juniBgpNewRouteNextHopMetric Unsigned32
  juniBgpNewRouteMplsInLabel Unsigned32
  juniBgpNewRouteMplsOutLabel Unsigned32
  juniBgpNewRouteLeaked TruthValue
  juniBgpNewRouteStale TruthValue

JuniBgpNewRouteFlapHistoryEntry  
SEQUENCE    
  juniBgpNewRouteFlapState INTEGER
  juniBgpNewRouteFlapFigureOfMerit Unsigned32
  juniBgpNewRouteFlapRemainingTime Unsigned32
  juniBgpNewRouteFlapSuppressThreshold Unsigned32
  juniBgpNewRouteFlapReuseThreshold Unsigned32
  juniBgpNewRouteFlapMaxHoldDownTime Unsigned32
  juniBgpNewRouteFlapHalfLifeReachable Unsigned32
  juniBgpNewRouteFlapHalfLifeUnreachable Unsigned32

JuniBgpNewRouteCommunityEntry  
SEQUENCE    
  juniBgpNewRouteCommunityNumber Unsigned32

JuniBgpNewRouteExtendedCommunityEntry  
SEQUENCE    
  juniBgpNewRouteExtendedCommunityNumber OCTET STRING

JuniBgpNewRouteClusterIdEntry  
SEQUENCE    
  juniBgpNewRouteClusterId Unsigned32

JuniBgpRouteEntry  
SEQUENCE    
  juniBgpRouteOriginatorId IpAddress
  juniBgpRouteAtomicAggregatePresent TruthValue
  juniBgpRouteMedPresent TruthValue
  juniBgpRouteLocalPrefPresent TruthValue
  juniBgpRouteAggregatorPresent TruthValue
  juniBgpRouteCommunitiesPresent TruthValue
  juniBgpRouteOriginatorIdPresent TruthValue
  juniBgpRouteClusterListPresent TruthValue
  juniBgpRouteWeight Unsigned32
  juniBgpRouteVrfName JuniVrfName
  juniBgpRouteAfi JuniBgpAfi
  juniBgpRouteSafi JuniBgpSafi
  juniBgpRoutePeer IpAddress
  juniBgpRouteIpAddrPrefixLen Integer32
  juniBgpRouteIpAddrPrefix IpAddress
  juniBgpRouteRouteType INTEGER
  juniBgpRouteOrigin INTEGER
  juniBgpRouteASPathSegment OCTET STRING
  juniBgpRouteNextHop IpAddress
  juniBgpRouteMultiExitDisc Unsigned32
  juniBgpRouteLocalPref Unsigned32
  juniBgpRouteAtomicAggregate INTEGER
  juniBgpRouteAggregatorAS Integer32
  juniBgpRouteAggregatorAddress IpAddress
  juniBgpRouteBestInIpRouteTable TruthValue
  juniBgpRouteUnknown OCTET STRING
  juniBgpRouteExtendedCommunitiesPresent TruthValue
  juniBgpRouteValid TruthValue
  juniBgpRouteSuppressedBy INTEGER
  juniBgpRouteNextHopReachable TruthValue
  juniBgpRouteSynchronizedWithIgp TruthValue
  juniBgpRoutePlaceInIpRouteTable TruthValue
  juniBgpRouteAdvertiseToExternalPeers TruthValue
  juniBgpRouteAdvertiseToInternalPeers TruthValue
  juniBgpRouteDistinguisher OCTET STRING
  juniBgpRouteMplsLabel Unsigned32
  juniBgpRouteNextHopMetric Unsigned32

JuniBgpRouteFlapHistoryEntry  
SEQUENCE    
  juniBgpRouteFlapState INTEGER
  juniBgpRouteFlapFigureOfMerit Unsigned32
  juniBgpRouteFlapRemainingTime Unsigned32
  juniBgpRouteFlapSuppressThreshold Unsigned32
  juniBgpRouteFlapReuseThreshold Unsigned32
  juniBgpRouteFlapMaxHoldDownTime Unsigned32
  juniBgpRouteFlapHalfLifeReachable Unsigned32
  juniBgpRouteFlapHalfLifeUnreachable Unsigned32

JuniBgpRouteCommunityEntry  
SEQUENCE    
  juniBgpRouteCommunityNumber Unsigned32

JuniBgpRouteExtendedCommunityEntry  
SEQUENCE    
  juniBgpRouteExtendedCommunityNumber OCTET STRING

JuniBgpRouteClusterIdEntry  
SEQUENCE    
  juniBgpRouteClusterId Unsigned32

Defined Values

juniBgpMIB 1.3.6.1.4.1.4874.2.2.29
The BGP Protocol MIB for the Juniper Networks enterprise.
MODULE-IDENTITY    

juniBgpObjects 1.3.6.1.4.1.4874.2.2.29.1
OBJECT IDENTIFIER    

juniBgpGeneralGroup 1.3.6.1.4.1.4874.2.2.29.1.1
OBJECT IDENTIFIER    

juniBgpLocalAsNumber 1.3.6.1.4.1.4874.2.2.29.1.1.1
Deprecated. The local autonomous system number. This object has been replaced by juniBgpFourOctetLocalAsNumber. It is still possible to get and set this object, but if the actual local AS number is greater than 65535, getting this object returns 23456 (AS-TRANS).
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpEnabled 1.3.6.1.4.1.4874.2.2.29.1.1.2
Set this object to true(1) in order to have BGP router enabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpIdentifier 1.3.6.1.4.1.4874.2.2.29.1.1.3
The BGP identifier of the local system. The identifier is the system router ID by default.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

juniBgpAlwaysCompareMed 1.3.6.1.4.1.4874.2.2.29.1.1.4
Set this object to true(1) in order to compare metrics for paths from neighors of different ASs.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpDefaultLocalPreference 1.3.6.1.4.1.4874.2.2.29.1.1.5
The default local preference.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

juniBgpEqualCostLimit 1.3.6.1.4.1.4874.2.2.29.1.1.6
Obsolete maximum equal cost paths to store in the routing table. This object has been replaced by the juniBgpVrfMaximumPathsEbgp object.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpClientToClientReflection 1.3.6.1.4.1.4874.2.2.29.1.1.7
Set this object to true(1) in order to have client-to-client route reflection enabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpClusterId 1.3.6.1.4.1.4874.2.2.29.1.1.8
The cluster ID. When this object is zero, the router ID will be used.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

juniBgpConfederationId 1.3.6.1.4.1.4874.2.2.29.1.1.9
The confederation ID. When this object is zero, the router is not in a confederation.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

juniBgpMissingAsWorst 1.3.6.1.4.1.4874.2.2.29.1.1.10
If this object is set to true(1) routes without a MED attribute are considered worse than routes with a MED attribute. If this object is set to false(0) routes without a MED attribute are considered better than routes with a MED attribute.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpResetAllConnectionType 1.3.6.1.4.1.4874.2.2.29.1.1.11
Writing a value to this object causes all sessions to all peers to be cleared; the value determines what type of clear is executed (hard clear, soft clear in, soft clear out, etc.). Reading this object has no effect and always returns resetTypeNoop.
Status: current Access: read-write
OBJECT-TYPE    
  JuniBgpResetConnectionType  

juniBgpAdvertiseInactive 1.3.6.1.4.1.4874.2.2.29.1.1.12
Set this object to true(1) in order to propagate received BGP routes which are not the best route in the IP forwarding table.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpEnforceFirstAs 1.3.6.1.4.1.4874.2.2.29.1.1.13
Set this object to true(1) in order to check whether the first AS number in the AS-path in routes from EBGP peers is consistent with the AS number of the peer.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpConfedCompareMed 1.3.6.1.4.1.4874.2.2.29.1.1.14
Set this object to true(1) in order to compare metrics for paths from neighors of different sub-ASs in the same confederation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpGlobalRetryInterval 1.3.6.1.4.1.4874.2.2.29.1.1.15
The default number of seconds before BGP retries to establish an outgoing BGP session.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpGlobalConfigKeepAliveInterval 1.3.6.1.4.1.4874.2.2.29.1.1.16
Default time interval in seconds for the KeepAlive timer for all peers. Zero means don't send KeepAlive messages.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpGlobalConfigHoldTime 1.3.6.1.4.1.4874.2.2.29.1.1.17
Default time interval in seconds for the Hold timer for all peers. Zero means don't expect KeepAlive message to be received.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 3..65535  

juniBgpGlobalAsOriginationInterval 1.3.6.1.4.1.4874.2.2.29.1.1.18
Default time interval in seconds for the MinASOriginationInterval timer for all peers.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

juniBgpExternalAdvertisementInterval 1.3.6.1.4.1.4874.2.2.29.1.1.19
Default time interval in seconds for the MinRouteAdvertisementInterval timer for all external peers.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpGlobalRibOutEnabled 1.3.6.1.4.1.4874.2.2.29.1.1.20
Set this object to true(1) in order to enable RIB-out by default for all peers, or to false(2) to disable RIB-out by default for all peers.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpOverloadShutdown 1.3.6.1.4.1.4874.2.2.29.1.1.21
Set this object to true(1) for BGP to shut itself down when it runs out of memory. Set this object to false(2) for BGP to continue running (with incomplete information) when it runs out of memory.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpLogNeighborChanges 1.3.6.1.4.1.4874.2.2.29.1.1.22
Set this object to true(1) for BGP log a message whenever a peer enters or leaves the established state.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpFastExternalFallover 1.3.6.1.4.1.4874.2.2.29.1.1.23
Set this object to true(1) for BGP to immediately bring down any directly adjacent EBGP session on a link down.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpInternalAdvertisementInterval 1.3.6.1.4.1.4874.2.2.29.1.1.24
Default time interval in seconds for the MinRouteAdvertisementInterval timer for all internal peers.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpMaxAsLimit 1.3.6.1.4.1.4874.2.2.29.1.1.25
Maximum length of received AS-path. Received routes with an AS-path longer than this are not placed in the IP forwarding table and are not propagated to other peers. Zero means no maximum length.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpOperationalState 1.3.6.1.4.1.4874.2.2.29.1.1.26
The BGP instance operational state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), up(1), down(2), overload(3)  

juniBgpPreviousOperationalState 1.3.6.1.4.1.4874.2.2.29.1.1.27
The BGP instance previous operational state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), up(1), down(2), overload(3)  

juniBgpAutomaticRouteTargetFilter 1.3.6.1.4.1.4874.2.2.29.1.1.28
Set this object to true(1) for BGP to enable automatic route-target filtering.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpDefaultIPv4Unicast 1.3.6.1.4.1.4874.2.2.29.1.1.29
Set this object to true(1) for BGP to automatically activate peers in the IPv4 unicast address family.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpRedistributeInternal 1.3.6.1.4.1.4874.2.2.29.1.1.30
Set this object to true(1) for BGP to automatically redistribute iBGP routes to IGP protocols.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpFourOctetLocalAsNumber 1.3.6.1.4.1.4874.2.2.29.1.1.31
The four-octet local autonomous system number. This attribute replaces the old two-octet local autonomous system number.
Status: current Access: read-write
OBJECT-TYPE    
  JuniBgpFourOctetAsNumber  

juniBgpConfederationPeersFilterList 1.3.6.1.4.1.4874.2.2.29.1.1.32
The confederation peers filter-list contains the name of an as-path access-list. Every neighbor whose remote-AS number matches this as-path access-list is considered a confederation peer. An empty string means that no confederation peers filter-list is configured.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpUnconfiguredAttributes 1.3.6.1.4.1.4874.2.2.29.1.1.33
On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
Status: current Access: read-write
OBJECT-TYPE    
  BITS juniBgpEnabled(0), juniBgpIdentifier(1), juniBgpAlwaysCompareMed(2), juniBgpDefaultLocalPreference(3), juniBgpEqualCostLimit(4), juniBgpClientToClientReflection(5), juniBgpClusterId(6), juniBgpConfederationId(7), juniBgpMissingAsWorst(8), juniBgpAdvertiseInactive(9), juniBgpEnforceFirstAs(10), juniBgpConfedCompareMed(11), juniBgpGlobalRetryInterval(12), juniBgpGlobalConfigKeepAliveInterval(13), juniBgpGlobalConfigHoldTime(14), juniBgpGlobalAsOriginationInterval(15), juniBgpExternalAdvertisementInterval(16), juniBgpGlobalRibOutEnabled(17), juniBgpOverloadShutdown(18), juniBgpLogNeighborChanges(19), juniBgpFastExternalFallover(20), juniBgpInternalAdvertisementInterval(21), juniBgpMaxAsLimit(22), juniBgpAutomaticRouteTargetFilter(23), juniBgpDefaultIPv4Unicast(24), juniBgpRedistributeInternal(25), juniBgpFourOctetLocalAsNumber(26), juniBgpConfederationPeersFilterList(27), juniBgpAdvertiseBestExternalToInternal(28), juniBgpGracefulRestartEnabled(29), juniBgpGracefulRestartRestartTime(30), juniBgpGracefulRestartStalePathsTime(31), juniBgpGracefulRestartPathSelectionDeferTimeLimit(32)  

juniBgpAdvertiseBestExternalToInternal 1.3.6.1.4.1.4874.2.2.29.1.1.34
If this object is set to true(1) then BGP advertises the best route received from external (and confederation) peers to internal peers. If this object is set to false(2) then BGP advertises the best route received from all peers to internal peers except if the best route was received from an internal peer in which case BGP doesn't advertise any route to internal peers.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpGracefulRestartEnabled 1.3.6.1.4.1.4874.2.2.29.1.1.35
Set this object to true(1) to enable BGP graceful restart.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniBgpGracefulRestartRestartTime 1.3.6.1.4.1.4874.2.2.29.1.1.36
The restart-time advertised in graceful-restart capabilities sent to all peers. This is the estimated time (in seconds) it will take for the BGP session to be re-established after a restart. This can be used to speed up routing convergence by the peer in case that this BGP speaker does not come back after a restart. This value is used by all peers unless overridden by juniBgpPeerGroupGracefulRestartRestartTime or juniBgpPeerGracefulRestartRestartTime.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..3600  

juniBgpGracefulRestartStalePathsTime 1.3.6.1.4.1.4874.2.2.29.1.1.37
The maximum amount of time in seconds we keep stale routes after a session goes down. This value is used for all peers unless it has been overridden by juniBgpPeerGroupGracefulRestartStalePathsTime or juniBgpPeerGracefulRestartStalePathsTime.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..3600  

juniBgpGracefulRestartPathSelectionDeferTimeLimit 1.3.6.1.4.1.4874.2.2.29.1.1.38
The maximum amount of time in seconds route selection is deferred after a restart.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..3600  

juniBgpPlatformSupportsNonStopForwarding 1.3.6.1.4.1.4874.2.2.29.1.1.39
Does this platform support non-stop forwarding?
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpDeviceCanPreserveForwardingState 1.3.6.1.4.1.4874.2.2.29.1.1.40
Is this router at this moment able to do a graceful restart (i.e. is it able to switch over from the primary controller to the standby controller without losing forwarding state on the line cards). The router may not be able to do a graceful restart because the platform does not support non-stop forwarding, because there is no secondary controller present, because the secondary controller is not in standby state, etc.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpLastRestartWasGraceful 1.3.6.1.4.1.4874.2.2.29.1.1.41
Was the most recent restart graceful? (i.e. was forwarding state preserved on the line cards during the most recent switch-over from the primary controller to the standby controller?)
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteTableStatisticsGroup 1.3.6.1.4.1.4874.2.2.29.1.2
OBJECT IDENTIFIER    

juniBgpBaselineTime 1.3.6.1.4.1.4874.2.2.29.1.2.1
The sysUpTime at which the counters were most recently baselined.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpDestinationCount 1.3.6.1.4.1.4874.2.2.29.1.2.2
Number of distinct destinations in the local RIB.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniBgpDestinationMemoryUsed 1.3.6.1.4.1.4874.2.2.29.1.2.3
Memory used by distinct destinations in the local RIB.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniBgpRouteCount 1.3.6.1.4.1.4874.2.2.29.1.2.4
Number of routes in the local RIB.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniBgpRouteMemoryUsed 1.3.6.1.4.1.4874.2.2.29.1.2.5
Memory used by routes in the local RIB.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniBgpSelectedRouteCount 1.3.6.1.4.1.4874.2.2.29.1.2.6
Number of routes selected for route table installation.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniBgpPathAttributeCount 1.3.6.1.4.1.4874.2.2.29.1.2.8
Number of entries in the path attribute database.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniBgpPathAttributeMemoryUsed 1.3.6.1.4.1.4874.2.2.29.1.2.9
Memory used by entries in the path attribute database.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniBgpRouteFlapHistoryCount 1.3.6.1.4.1.4874.2.2.29.1.2.10
Number of routes with active route flap histories.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniBgpRouteFlapHistoryMemoryUsed 1.3.6.1.4.1.4874.2.2.29.1.2.11
Memory used by routes with active route flap histories.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniBgpSuppressedRouteCount 1.3.6.1.4.1.4874.2.2.29.1.2.12
Number of routes suppressed due to route flap.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniBgpConfederationPeerTable 1.3.6.1.4.1.4874.2.2.29.1.3
The Juniper BGP Confederation Peer Table describes the BGP-specific characteristics of confederation peers.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpConfederationPeerEntry

juniBgpConfederationPeerEntry 1.3.6.1.4.1.4874.2.2.29.1.3.1
The BGP Confederation Peer Entry describes BGP-specific characteristics of one confederation peer.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  JuniBgpConfederationPeerEntry  

juniBgpConfederationPeerAsNumber 1.3.6.1.4.1.4874.2.2.29.1.3.1.1
The AsNumber of this confederation peer.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

juniBgpConfederationPeerRowStatus 1.3.6.1.4.1.4874.2.2.29.1.3.1.2
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
Status: deprecated Access: read-create
OBJECT-TYPE    
  RowStatus  

juniBgpFourOctetConfederationPeerTable 1.3.6.1.4.1.4874.2.2.29.1.28
The BGP New Confederation Peer Table describes the BGP-specific characteristics of confederation peers using four-octet AS-numbers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpFourOctetConfederationPeerEntry

juniBgpFourOctetConfederationPeerEntry 1.3.6.1.4.1.4874.2.2.29.1.28.1
The BGP New Confederation Peer Entry describes BGP-specific characteristics of one confederation peer using four-octet AS-numbers.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpFourOctetConfederationPeerEntry  

juniBgpFourOctetConfederationPeerAsNumber 1.3.6.1.4.1.4874.2.2.29.1.28.1.1
The four-octet AS-number of this confederation peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpFourOctetAsNumber  

juniBgpFourOctetConfederationPeerRowStatus 1.3.6.1.4.1.4874.2.2.29.1.28.1.2
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniBgpPeerTable 1.3.6.1.4.1.4874.2.2.29.1.4
The Juniper BGP Peer Table describes the BGP-specific characteristics of peers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpPeerEntry

juniBgpPeerEntry 1.3.6.1.4.1.4874.2.2.29.1.4.1
The BGP Peer Entry describes BGP-specific characteristics of one peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpPeerEntry  

juniBgpPeerVrfName 1.3.6.1.4.1.4874.2.2.29.1.4.1.1
The name of the VPN Routing Forwarding (VRF) instance in which this peer is configured. The empty string indicates that this peer is not in a VRF.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniVrfName  

juniBgpPeerRemoteAddress 1.3.6.1.4.1.4874.2.2.29.1.4.1.2
The remote IP address of this entry's BGP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniBgpPeerAdminStatus 1.3.6.1.4.1.4874.2.2.29.1.4.1.3
The desired state of the BGP connection. A transition from 'stop' to 'start' will cause the BGP Start Event to be generated. A transition from 'start' to 'stop' will cause the BGP Stop Event to be generated. This parameter can be used to restart BGP peer connections. Care should be used in providing write access to this object without adequate authentication.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER stop(1), start(2)  

juniBgpPeerState 1.3.6.1.4.1.4874.2.2.29.1.4.1.4
The BGP peer connection state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER stop(0), idle(1), connect(2), active(3), opensent(4), openconfirm(5), established(6), removing(7)  

juniBgpPeerNegotiatedVersion 1.3.6.1.4.1.4874.2.2.29.1.4.1.5
The negotiated version of BGP running between the two peers.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

juniBgpPeerLocalAddress 1.3.6.1.4.1.4874.2.2.29.1.4.1.6
The local IP address of this entry's BGP connection.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

juniBgpPeerLocalAddressMask 1.3.6.1.4.1.4874.2.2.29.1.4.1.7
The local IP address mask of this entry's BGP connection.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

juniBgpPeerLocalPort 1.3.6.1.4.1.4874.2.2.29.1.4.1.8
The local port for the TCP connection between the BGP peers.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpPeerRemoteAsNumber 1.3.6.1.4.1.4874.2.2.29.1.4.1.9
Deprecated. The peer's autonomous system number. This object has been replaced by juniBgpPeerFourOctetRemoteAsNumber. It is still possible to get and set this object, but if the actual remote AS number is greater than 65535, getting this object returns 23456 (AS-TRANS).
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpPeerRemotePort 1.3.6.1.4.1.4874.2.2.29.1.4.1.10
The remote port for the TCP connection between the BGP peers. Note that the objects bgpPeerLocalAddr, bgpPeerLocalPort, bgpPeerRemoteAddr and bgpPeerRemotePort provide the appropriate reference to the standard MIB TCP connection table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpPeerInUpdates 1.3.6.1.4.1.4874.2.2.29.1.4.1.11
The number of BGP UPDATE messages received on this connection. This object should be initialized to zero (0) when the connection is established.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniBgpPeerOutUpdates 1.3.6.1.4.1.4874.2.2.29.1.4.1.12
The number of BGP UPDATE messages transmitted on this connection. This object should be initialized to zero (0) when the connection is established.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniBgpPeerInTotalMessages 1.3.6.1.4.1.4874.2.2.29.1.4.1.13
The total number of messages received from the remote peer on this connection. This object should be initialized to zero when the connection is established.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniBgpPeerOutTotalMessages 1.3.6.1.4.1.4874.2.2.29.1.4.1.14
The total number of messages transmitted to the remote peer on this connection. This object should be initialized to zero when the connection is established.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniBgpPeerLastErrorCode 1.3.6.1.4.1.4874.2.2.29.1.4.1.15
The last error code and subcode seen by this peer on this connection. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte OCTET STRING contains the error code, and the second byte contains the subcode.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

juniBgpPeerLastResetReason 1.3.6.1.4.1.4874.2.2.29.1.4.1.16
The string representing the last error code seen by this peer on this connection. If no error has occurred, this string is null.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

juniBgpPeerFsmEstablishedTransitions 1.3.6.1.4.1.4874.2.2.29.1.4.1.17
The total number of times the BGP FSM transitioned into the established state.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniBgpPeerFsmEstablishedTime 1.3.6.1.4.1.4874.2.2.29.1.4.1.18
This timer indicates how long (in seconds) this peer has been in the Established state or how long since this peer was last in the Established state. It is set to zero when a new peer is configured or the router is booted.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniBgpPeerRetryInterval 1.3.6.1.4.1.4874.2.2.29.1.4.1.19
Time interval in seconds for the ConnectRetry timer. The suggested value for this timer is 120 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

juniBgpPeerHoldTime 1.3.6.1.4.1.4874.2.2.29.1.4.1.20
Time interval in seconds for the Hold Timer established with the peer. The value of this object is calculated by this BGP speaker by using the smaller of the value in bgpPeerHoldTimeConfigured and the Hold Time received in the OPEN message. This value must be at lease three seconds if it is not zero (0) in which case the Hold Timer has not been established with the peer, or, the value of bgpPeerHoldTimeConfigured is zero (0).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0 | 3..65535  

juniBgpPeerKeepAliveInterval 1.3.6.1.4.1.4874.2.2.29.1.4.1.21
Time interval in seconds for the KeepAlive timer established with the peer. The value of this object is calculated by this BGP speaker such that, when compared with bgpPeerHoldTime, it has the same proportion as what bgpPeerKeepAliveConfigured has when compared with bgpPeerHoldTimeConfigured. If the value of this object is zero (0), it indicates that the KeepAlive timer has not been established with the peer, or, the value of bgpPeerKeepAliveConfigured is zero (0).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..21845  

juniBgpPeerConfigHoldTime 1.3.6.1.4.1.4874.2.2.29.1.4.1.22
Time interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an OPEN message received from the peer when determining the Hold Time (bgpPeerHoldTime) with the peer. This value must not be less than three seconds if it is not zero (0) in which case the Hold Time is NOT to be established with the peer. The suggested value for this timer is 90 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0 | 3..65535  

juniBgpPeerConfigKeepAliveInterval 1.3.6.1.4.1.4874.2.2.29.1.4.1.23
Time interval in seconds for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages' frequency relative to the value specified in bgpPeerHoldTimeConfigured; the actual time interval for the KEEPALIVE messages is indicated by bgpPeerKeepAlive. A reasonable maximum value for this timer would be configured to be one third of that of bgpPeerHoldTimeConfigured. If the value of this object is zero (0), no periodical KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..21845  

juniBgpPeerAsOriginationInterval 1.3.6.1.4.1.4874.2.2.29.1.4.1.24
Time interval in seconds for the MinASOriginationInterval timer. The suggested value for this timer is 10 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

juniBgpPeerAdvertisementInterval 1.3.6.1.4.1.4874.2.2.29.1.4.1.25
Time interval in seconds for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

juniBgpPeerInUpdateElapsedTime 1.3.6.1.4.1.4874.2.2.29.1.4.1.26
Elapsed time in seconds since the last BGP UPDATE message was received from the peer. Each time bgpPeerInUpdates is incremented, the value of this object is set to zero (0).
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniBgpPeerDescription 1.3.6.1.4.1.4874.2.2.29.1.4.1.27
Peer textual description.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..80)  

juniBgpPeerRemoteIdentifier 1.3.6.1.4.1.4874.2.2.29.1.4.1.28
Peer's remote router ID.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

juniBgpPeerWeight 1.3.6.1.4.1.4874.2.2.29.1.4.1.29
The weight assigned to routes learned from peer.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerEbgpMultihop 1.3.6.1.4.1.4874.2.2.29.1.4.1.30
The EBGP multihop is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerEbgpMultihopTtl 1.3.6.1.4.1.4874.2.2.29.1.4.1.31
Maximum number of hops to the external peer (only relevant if EBGP multihop turned on).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..255  

juniBgpPeerUpdateSource 1.3.6.1.4.1.4874.2.2.29.1.4.1.32
The source IP address for peer connections.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

juniBgpPeerMd5Password 1.3.6.1.4.1.4874.2.2.29.1.4.1.33
The password for MD5 authentication. Reading this object always results in an OCTET STRING of length zero.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

juniBgpPeerMaxUpdateSize 1.3.6.1.4.1.4874.2.2.29.1.4.1.34
The maximum size in bytes of transmitted UPDATE messages.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerType 1.3.6.1.4.1.4874.2.2.29.1.4.1.35
The type of peer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER peerTypeInternal(1), peerTypeExternal(2), peerTypeConfederation(3), peerTypeUnknown(4)  

juniBgpPeerReceivedCapabilitiesOption 1.3.6.1.4.1.4874.2.2.29.1.4.1.36
The peer sent the capabilities optional parameter in its open message.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerReceivedCapabilityMultiProtocol 1.3.6.1.4.1.4874.2.2.29.1.4.1.37
The peer has advertised the multi-protocol capability to us.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerReceivedCapabilityRouteRefresh 1.3.6.1.4.1.4874.2.2.29.1.4.1.38
The peer has advertised the route-refresh capability to us.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerReceivedCapabilityRouteRefreshCisco 1.3.6.1.4.1.4874.2.2.29.1.4.1.39
The peer has advertised the route-refresh-cisco capability to us.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerResetConnectionType 1.3.6.1.4.1.4874.2.2.29.1.4.1.40
Writing a value to this object causes the session to the peer to be cleared; the value determines what type of clear is executed (hard clear, soft clear in, soft clear out, etc.). Reading this object has no effect and always returns resetTypeNoop.
Status: current Access: read-create
OBJECT-TYPE    
  JuniBgpResetConnectionType  

juniBgpPeerRowStatus 1.3.6.1.4.1.4874.2.2.29.1.4.1.41
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniBgpPeerLocalAsNumber 1.3.6.1.4.1.4874.2.2.29.1.4.1.42
Deprecated. The local autonomous system number to be used for this peer. Value zero (0) means that the global local automous system number (as specified in the object juniBgpPeerLocalAsNumber) is used. This object has been replaced by juniBgpPeerFourOctetLocalAsNumber. It is still possible to get and set this object, but if the actual local AS number is greater than 65535, getting this object returns AS-TRANS (23456).
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpPeerFourOctetRemoteAsNumber 1.3.6.1.4.1.4874.2.2.29.1.4.1.43
The peer's four-octet autonomous system number.
Status: current Access: read-create
OBJECT-TYPE    
  JuniBgpFourOctetAsNumber  

juniBgpPeerFourOctetLocalAsNumber 1.3.6.1.4.1.4874.2.2.29.1.4.1.44
The four-octet local autonomous system number to be used for this peer. Value zero (0) means that the global local automous system number (as specified in the object juniBgpPeerFourOctetLocalAsNumber) is used.
Status: current Access: read-create
OBJECT-TYPE    
  JuniBgpFourOctetAsNumber  

juniBgpPeerReceivedCapabilityFourOctetAsNumbers 1.3.6.1.4.1.4874.2.2.29.1.4.1.45
The peer has advertised the four-octet-as-numbers capability to us.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerReceivedCapabilityDynamicCapabilityNeg 1.3.6.1.4.1.4874.2.2.29.1.4.1.46
The peer has advertised the dynamic-capability-negotiation capability to us.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerShouldAdvertiseCapabilitiesOption 1.3.6.1.4.1.4874.2.2.29.1.4.1.47
Set this object to true if the capabilities option should be included in OPEN messages sent to this peer. Even if this object is set to true, BGP may decide not to include the capabilities option in OPEN messages sent to this peer (for example when it is detected that the peer does not support capability negotiation). The juniBgpPeerSentCapabilitiesOption can be used to determine whether or not the OPEN message sent to the peer actually contained the capabilities option.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerShouldAdvertiseCapabilityRouteRefresh 1.3.6.1.4.1.4874.2.2.29.1.4.1.48
Set this object to true if the route-refresh capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the route-refresh capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the route-refresh capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityRouteRefresh can be used to determine whether or not the capability was actually advertised to the peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerShouldAdvertiseCapabilityRouteRefreshCisco 1.3.6.1.4.1.4874.2.2.29.1.4.1.49
Set this object to true if the route-refresh-cisco capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the route-refresh-cisco capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the route-refresh-cisco capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityRouteRefreshCisco can be used to determine whether or not the capability was actually advertised to the peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerShouldAdvertiseCapabilityFourOctetAsNumbers 1.3.6.1.4.1.4874.2.2.29.1.4.1.50
Set this object to true if the four-octet-as-numbers capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the four-octet-as-numbers capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the four-octet-as-numbers capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityFourOctetAsNumbers can be used to determine whether or not the capability was actually advertised to the peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerShouldAdvertiseCapabilityDynamicCapabilityNeg 1.3.6.1.4.1.4874.2.2.29.1.4.1.51
Set this object to true if the dynamic-capability-negotiation capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the dynamic-capability-negotiation capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the dynamic-capability-negotiation capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityDynamicCapabilityNeg can be used to determine whether or not the capability was actually advertised to the peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerSentCapabilitiesOption 1.3.6.1.4.1.4874.2.2.29.1.4.1.52
We sent the capabilities optional parameter in the OPEN message to this peer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerSentCapabilityMultiProtocol 1.3.6.1.4.1.4874.2.2.29.1.4.1.53
We advertised the multi-protocol capability to this peer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerSentCapabilityRouteRefresh 1.3.6.1.4.1.4874.2.2.29.1.4.1.54
We advertised the route-refresh capability to this peer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerSentCapabilityRouteRefreshCisco 1.3.6.1.4.1.4874.2.2.29.1.4.1.55
We advertised the route-refresh-cisco capability to this peer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerSentCapabilityFourOctetAsNumbers 1.3.6.1.4.1.4874.2.2.29.1.4.1.56
We advertised the four-octet-as-numbers capability to this peer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerSentCapabilityDynamicCapabilityNeg 1.3.6.1.4.1.4874.2.2.29.1.4.1.57
We advertised the dynamic-capability-negotiation capability to this peer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerReceivedUnsupportedOptionalParameterNotification 1.3.6.1.4.1.4874.2.2.29.1.4.1.58
We received an unsupported optional parameter notification from this peer. This indicates that the peer does not support capability negotiation. When this object is set to true, we do not include the capabilities optional parameter in OPEN messages sent to this peer. A hard clear of the session is needed to retry sending the capabilities optional parameter.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerReceivedUnsupportedCapabilityNotification 1.3.6.1.4.1.4874.2.2.29.1.4.1.59
We received an unsupported capability notification from this peer. This often happens because the peer did not recognize a capability which we advertised to the peer and that peer incorrectly send back an unsupported capability notification (the peer should ignore the unsupported capability instead). When this object is set to true, we do not advertise capabilities that the peer does not support.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerUnconfiguredAttributes 1.3.6.1.4.1.4874.2.2.29.1.4.1.60
On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
Status: current Access: read-create
OBJECT-TYPE    
  BITS juniBgpPeerAdminStatus(0), juniBgpPeerRetryInterval(1), juniBgpPeerConfigHoldTime(2), juniBgpPeerConfigKeepAliveInterval(3), juniBgpPeerAsOriginationInterval(4), juniBgpPeerAdvertisementInterval(5), juniBgpPeerDescription(6), juniBgpPeerWeight(7), juniBgpPeerEbgpMultihop(8), juniBgpPeerEbgpMultihopTtl(9), juniBgpPeerUpdateSource(10), juniBgpPeerMd5Password(11), juniBgpPeerMaxUpdateSize(12), juniBgpPeerFourOctetRemoteAsNumber(13), juniBgpPeerFourOctetLocalAsNumber(14), juniBgpPeerShouldAdvertiseCapabilitiesOption(15), juniBgpPeerShouldAdvertiseCapabilityRouteRefresh(16), juniBgpPeerShouldAdvertiseCapabilityRouteRefreshCisco(17), juniBgpPeerShouldAdvertiseCapabilityFourOctetAsNumbers(18), juniBgpPeerShouldAdvertiseCapabilityDynamicCapabilityNeg(19), juniBgpPeerSiteOfOrigin(20), juniBgpPeerLenient(21), juniBgpPeerShouldAdvertiseCapabilityOldDynamicCapabilityNeg(22), juniBgpPeerPassive(23), juniBgpPeerShouldAdvertiseCapabilityGracefulRestart(24), juniBgpPeerGracefulRestartRestartTime(25), juniBgpPeerGracefulRestartStalePathsTime(26), juniBgpPeerBfdEnabled(27), juniBgpPeerBfdMinTransmitInterval(28), juniBgpPeerBfdMinReceiveInterval(29), juniBgpPeerBfdMultiplier(30), juniBgpPeerIbgpSinglehop(31)  

juniBgpPeerSiteOfOrigin 1.3.6.1.4.1.4874.2.2.29.1.4.1.61
The site-of-origin. This site-of-origin is added to the extended communities for all routes received from the peer. When sending routes to this peer all routes with this extended community are filtered. The null extended community (all 8 bytes zero) means that no site-of-origin is configured for this peer. It is not allowed to set this object to any extended community other than a site-of-origin type of extended community or null.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(8)  

juniBgpPeerLenient 1.3.6.1.4.1.4874.2.2.29.1.4.1.62
Enable Lenient behavior for this peer so that it is more tolerant of finite state machine errors and malformed messages received from the remote peer and avoids terminating the peer session whenever possible.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerReceivedCapabilityOldDynamicCapabilityNeg 1.3.6.1.4.1.4874.2.2.29.1.4.1.63
The peer has advertised the old deprecated dynamic-capability- negotiation capability to us.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerShouldAdvertiseCapabilityOldDynamicCapabilityNeg 1.3.6.1.4.1.4874.2.2.29.1.4.1.64
Set this object to true if the deprecated-dynamic-capability- negotiation capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the deprecated-dynamic-capability-negotiation capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the deprecated-dynamic-capability-negotiation capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityOldDynamicCapabilityNeg can be used to determine whether or not the capability was actually advertised to the peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerSentCapabilityOldDynamicCapabilityNeg 1.3.6.1.4.1.4874.2.2.29.1.4.1.65
We advertised the old-dynamic-capability-negotiation capability to this peer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerPassive 1.3.6.1.4.1.4874.2.2.29.1.4.1.66
Set this object to true(1) to make this a passive peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerDynamic 1.3.6.1.4.1.4874.2.2.29.1.4.1.67
This object return true(1) if this is a dynamically created peer or false(2) if this is a configured peer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerShouldAdvertiseCapabilityGracefulRestart 1.3.6.1.4.1.4874.2.2.29.1.4.1.68
Set this object to true if the graceful-restart capability should be advertised to all peers. Even if this object is set to true, BGP may decide not to advertise the graceful-restart capability to a peer (for example when graceful-restart is not enabled or when it is detected that the peer does not support capability negotiation). The juniBgpPeerSentCapabilityGracefulRestart can be used to determine whether or not the capability was actually advertised to the peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerSentCapabilityGracefulRestart 1.3.6.1.4.1.4874.2.2.29.1.4.1.69
We advertised the graceful-restart capability to this peer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerReceivedCapabilityGracefulRestart 1.3.6.1.4.1.4874.2.2.29.1.4.1.70
The peer has advertised the graceful-restart capability to us.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGracefulRestartRestartTime 1.3.6.1.4.1.4874.2.2.29.1.4.1.71
The restart-time advertised in the graceful-restart capability sent to this peer. This is the estimated time (in seconds) it will take for the BGP session to be re-established after a restart. This can be used to speed up routing convergence by the peer in case that this BGP speaker does not come back after a restart. This value (if configured) overrides the global value configured in juniBgpGracefulRestartRestartTime and the value for the peer-group configured in juniBgpPeerGroupGracefulRestartRestartTime.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..3600  

juniBgpPeerGracefulRestartStalePathsTime 1.3.6.1.4.1.4874.2.2.29.1.4.1.72
The maximum amount of time in seconds we keep stale routes after the session to this peer goes down. This value (if configured) overrides the global value configured in juniBgpGracefulRestartStalePathsTime and the value for the peer-group configured in juniBgpPeerGroupGracefulRestartStalePathsTime.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..3600  

juniBgpPeerSentGracefulRestartRestartState 1.3.6.1.4.1.4874.2.2.29.1.4.1.73
Value true(1) indicates that the OPEN message most recently sent to this peer contained the graceful-restart capability with the Restart-State (R) bit in the Restart Flags field set to one (this indicates that BGP has experienced a restart).
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerReceivedGracefulRestartRestartState 1.3.6.1.4.1.4874.2.2.29.1.4.1.74
Value true(1) indicates that the OPEN message most recently received from this peer contained the graceful-restart capability with the Restart-State (R) bit in the Restart Flags field set to one (this indicates that the peer has experienced a restart).
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerSentGracefulRestartRestartTime 1.3.6.1.4.1.4874.2.2.29.1.4.1.75
The restart time in seconds field in the graceful-restart capability which we sent to the peer.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..3600  

juniBgpPeerReceivedGracefulRestartRestartTime 1.3.6.1.4.1.4874.2.2.29.1.4.1.76
The restart time in seconds field in the graceful-restart capability which we received from the peer.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpPeerTimeUntilGracefulRestartRestartTimerExpires 1.3.6.1.4.1.4874.2.2.29.1.4.1.77
If the restart-timer is running this object contains the number of seconds before it will expire. If the restart-timer is not running this object contains zero. The restart-timer is used to limit the amount of time that we are willing to wait for the session to come back up after the peer restarts.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpPeerTimeUntilGracefulRestartStalePathsTimerExpires 1.3.6.1.4.1.4874.2.2.29.1.4.1.78
If the stale-paths-timer is running this object contains the number of seconds before it will expire. If the stale-paths-timer is not running this object contains zero. The stale-paths-timer is used to limit the amount of time that we are willing continue using stale routes from a peer after that peer restarts.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..3600  

juniBgpPeerBfdEnabled 1.3.6.1.4.1.4874.2.2.29.1.4.1.79
Value true(1) the BFD is enabled for this peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerBfdMinTransmitInterval 1.3.6.1.4.1.4874.2.2.29.1.4.1.80
The minimum interval (in milliseconds) between BFD packets sent to the remote BFD speaker. In other words, it specifies the maximum rate at which we are willing to send BFD packets.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 100..65535  

juniBgpPeerBfdMinReceiveInterval 1.3.6.1.4.1.4874.2.2.29.1.4.1.81
The minimum interval (in milliseconds) between BFD packets received from the remote BFD speaker. In other words, it specifies the maximum rate at which we are willing to receive BFD packets.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 100..65535  

juniBgpPeerBfdMultiplier 1.3.6.1.4.1.4874.2.2.29.1.4.1.82
How many BFD packets can be missed before the BFD session is declared down.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..255  

juniBgpPeerBfdSessionUp 1.3.6.1.4.1.4874.2.2.29.1.4.1.83
Is the BFD session up.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerBfdDetectionTime 1.3.6.1.4.1.4874.2.2.29.1.4.1.84
The BFD detection time (in milliseconds) negotiated with the remote BFD speaker. In other words, how quickly can a broken connection be detected.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

juniBgpPeerIbgpSinglehop 1.3.6.1.4.1.4874.2.2.29.1.4.1.85
The IBGP single-hop is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerProposedAfiSafiPeerTable 1.3.6.1.4.1.4874.2.2.29.1.5
The Juniper BGP PeerProposedAfiSafi Peer Table describes the BGP-specific AFI and SAFIs a peer proposed.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpPeerProposedAfiSafiPeerEntry

juniBgpPeerProposedAfiSafiPeerEntry 1.3.6.1.4.1.4874.2.2.29.1.5.1
The BGP PeerProposedAfiSafi Peer Entry describes a BGP-specific AFI/SAFIs proposed by one peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpPeerProposedAfiSafiPeerEntry  

juniBgpPeerProposedAfiSafiPeerVrfName 1.3.6.1.4.1.4874.2.2.29.1.5.1.1
The name of the VPN Routing Forwarding (VRF) instance in which this peer is configured. The empty string indicates that this peer is not in a VRF.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniVrfName  

juniBgpPeerProposedAfiSafiPeerRemoteAddr 1.3.6.1.4.1.4874.2.2.29.1.5.1.2
The remote IP address of this entry's BGP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniBgpPeerProposedAfiSafiPeerAfi 1.3.6.1.4.1.4874.2.2.29.1.5.1.3
The AFI proposed by this peer to us.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpAfi  

juniBgpPeerProposedAfiSafiPeerSafi 1.3.6.1.4.1.4874.2.2.29.1.5.1.4
The SAFI proposed by this peer to us.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpSafi  

juniBgpPeerProposedAfiSafiPeerRowStatus 1.3.6.1.4.1.4874.2.2.29.1.5.1.5
Should always be active according to the Row Status convention.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

juniBgpLocalProposedAfiSafiPeerTable 1.3.6.1.4.1.4874.2.2.29.1.6
The Juniper BGP LocalProposedAfiSafi Peer Table describes the BGP-specific AFI and SAFIs proposed to the peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpLocalProposedAfiSafiPeerEntry

juniBgpLocalProposedAfiSafiPeerEntry 1.3.6.1.4.1.4874.2.2.29.1.6.1
The BGP LocalProposedAfiSafi Peer Entry describes a BGP-specific AFI/SAFIs proposed to one peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpLocalProposedAfiSafiPeerEntry  

juniBgpLocalProposedAfiSafiPeerVrfName 1.3.6.1.4.1.4874.2.2.29.1.6.1.1
The name of the VPN Routing Forwarding (VRF) instance in which this peer is configured. The empty string indicates that this peer is not in a VRF.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniVrfName  

juniBgpLocalProposedAfiSafiPeerRemoteAddr 1.3.6.1.4.1.4874.2.2.29.1.6.1.2
The remote IP address of this entry's BGP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniBgpLocalProposedAfiSafiPeerAfi 1.3.6.1.4.1.4874.2.2.29.1.6.1.3
The AFI we proposed to this peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpAfi  

juniBgpLocalProposedAfiSafiPeerSafi 1.3.6.1.4.1.4874.2.2.29.1.6.1.4
The SAFI we proposed to this peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpSafi  

juniBgpLocalProposedAfiSafiPeerRowStatus 1.3.6.1.4.1.4874.2.2.29.1.6.1.5
Should always be active according to the Row Status convention.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

juniBgpExchangedAfiSafiPeerTable 1.3.6.1.4.1.4874.2.2.29.1.7
The Juniper BGP PeerExchangedAfiSafi Peer Table describes the BGP-specific AFI and SAFIs a peer exchanged.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpExchangedAfiSafiPeerEntry

juniBgpExchangedAfiSafiPeerEntry 1.3.6.1.4.1.4874.2.2.29.1.7.1
The BGP ExchangedAfiSafi Peer Entry describes a BGP-specific AFI/SAFIs exchanged by one peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpExchangedAfiSafiPeerEntry  

juniBgpExchangedAfiSafiPeerVrfName 1.3.6.1.4.1.4874.2.2.29.1.7.1.1
The name of the VPN Routing Forwarding (VRF) instance in which this peer is configured. The empty string indicates that this peer is not in a VRF.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniVrfName  

juniBgpExchangedAfiSafiPeerRemoteAddr 1.3.6.1.4.1.4874.2.2.29.1.7.1.2
The remote IP address of this entry's BGP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniBgpExchangedAfiSafiPeerAfi 1.3.6.1.4.1.4874.2.2.29.1.7.1.3
The AFI which we exchange with this peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpAfi  

juniBgpExchangedAfiSafiPeerSafi 1.3.6.1.4.1.4874.2.2.29.1.7.1.4
The SAFI which we exchange with this peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpSafi  

juniBgpExchangedAfiSafiPeerRowStatus 1.3.6.1.4.1.4874.2.2.29.1.7.1.5
Should always be active according to the Row Status convention.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

juniBgpPeerDynamicCapabilityTable 1.3.6.1.4.1.4874.2.2.29.1.29
The BGP PeerDynamicCapbility Table describes which dynamic capbilities we proposed to the peer, which the peer proposed to us, and which are being used.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpPeerDynamicCapabilityEntry

juniBgpPeerDynamicCapabilityEntry 1.3.6.1.4.1.4874.2.2.29.1.29.1
The BGP PeerDynamicCapbility Entry describes one dynamic capability.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpPeerDynamicCapabilityEntry  

juniBgpPeerDynamicCapabilityPeerVrfName 1.3.6.1.4.1.4874.2.2.29.1.29.1.1
The name of the VPN Routing Forwarding (VRF) instance in which this peer is configured. The empty string indicates that this peer is not in a VRF.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniVrfName  

juniBgpPeerDynamicCapabilityPeerRemoteAddr 1.3.6.1.4.1.4874.2.2.29.1.29.1.2
The remote IP address of this entry's BGP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniBgpPeerDynamicCapabilityCode 1.3.6.1.4.1.4874.2.2.29.1.29.1.3
The capability code for the dynamic capability.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

juniBgpPeerDynamicCapabilitySent 1.3.6.1.4.1.4874.2.2.29.1.29.1.4
Returns true if we advertised capability code juniBgpPeerDynamicCapabilityCode in the dynamic-capability-negotiation capability which we sent to this peer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerDynamicCapabilityReceived 1.3.6.1.4.1.4874.2.2.29.1.29.1.5
Returns true if the peer advertised capability code juniBgpPeerDynamicCapabilityCode in the dynamic-capability-negotiation capability which this peer sent to us.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyTable 1.3.6.1.4.1.4874.2.2.29.1.8
The Juniper BGP Peer Address Family Table describes the BGP-specific attributes of an Address Family for a peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpPeerAddressFamilyEntry

juniBgpPeerAddressFamilyEntry 1.3.6.1.4.1.4874.2.2.29.1.8.1
The BGP ExchangedAfiSafi Peer Entry describes a BGP-specific AFI/SAFIs exchanged by one peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpPeerAddressFamilyEntry  

juniBgpPeerAddressFamilyVrfName 1.3.6.1.4.1.4874.2.2.29.1.8.1.1
The name of the VPN Routing Forwarding (VRF) instance in which this peer is configured. The empty string indicates that this peer is not in a VRF.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniVrfName  

juniBgpPeerAddressFamilyAfi 1.3.6.1.4.1.4874.2.2.29.1.8.1.2
The AFI of the address-family in which this peer is configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpAfi  

juniBgpPeerAddressFamilySafi 1.3.6.1.4.1.4874.2.2.29.1.8.1.3
The SAFI of the address-family in which this peer is configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpSafi  

juniBgpPeerAddressFamilyRemoteAddress 1.3.6.1.4.1.4874.2.2.29.1.8.1.4
The remote IP address of this entry's BGP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniBgpPeerAddressFamilyPeerGroup 1.3.6.1.4.1.4874.2.2.29.1.8.1.5
Peer group membership (null if none).
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerAddressFamilyDefaultOriginate 1.3.6.1.4.1.4874.2.2.29.1.8.1.6
Set this object to true(1) in order to advertise a default route to this peer, if present.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyNextHopSelf 1.3.6.1.4.1.4874.2.2.29.1.8.1.7
Set this object to true(1) in order to always advertise this router as the next hop.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilySendCommunity 1.3.6.1.4.1.4874.2.2.29.1.8.1.8
Set this object to true(1) in order to send COMMUNITIES attributes in updates.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyDistributeListIn 1.3.6.1.4.1.4874.2.2.29.1.8.1.9
The inbound distribute IP access list name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

juniBgpPeerAddressFamilyDistributeListOut 1.3.6.1.4.1.4874.2.2.29.1.8.1.10
The outbound distribute IP access list name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

juniBgpPeerAddressFamilyPrefixListIn 1.3.6.1.4.1.4874.2.2.29.1.8.1.11
The inbound IP prefix list name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

juniBgpPeerAddressFamilyPrefixListOut 1.3.6.1.4.1.4874.2.2.29.1.8.1.12
The outbound IP prefix list name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

juniBgpPeerAddressFamilyPrefixTreeIn 1.3.6.1.4.1.4874.2.2.29.1.8.1.13
The inbound IP prefix tree name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

juniBgpPeerAddressFamilyPrefixTreeOut 1.3.6.1.4.1.4874.2.2.29.1.8.1.14
The outbound IP prefix tree name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

juniBgpPeerAddressFamilyFilterListIn 1.3.6.1.4.1.4874.2.2.29.1.8.1.15
The inbound filter AS path list name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

juniBgpPeerAddressFamilyFilterListOut 1.3.6.1.4.1.4874.2.2.29.1.8.1.16
The outbound filter AS path list name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

juniBgpPeerAddressFamilyFilterListWeight 1.3.6.1.4.1.4874.2.2.29.1.8.1.17
The weight filter AS path list name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

juniBgpPeerAddressFamilyFilterListWeightValue 1.3.6.1.4.1.4874.2.2.29.1.8.1.18
The weight to apply on weight filter list matches.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerAddressFamilyRouteMapIn 1.3.6.1.4.1.4874.2.2.29.1.8.1.19
The inbound route-map name. An empty string means no inbound route-map.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerAddressFamilyRouteMapOut 1.3.6.1.4.1.4874.2.2.29.1.8.1.20
The outbound route-map name. An empty string means no outbound route-map.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerAddressFamilyRouteReflectorClient 1.3.6.1.4.1.4874.2.2.29.1.8.1.21
The peer is a route reflector client.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyRouteLimitWarn 1.3.6.1.4.1.4874.2.2.29.1.8.1.22
Log a warning if pathCount exceeds this value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerAddressFamilyRouteLimitReset 1.3.6.1.4.1.4874.2.2.29.1.8.1.23
Reset connection is pathCount exceeds this value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerAddressFamilyRouteLimitWarnOnly 1.3.6.1.4.1.4874.2.2.29.1.8.1.24
Warn, but do not reset, if the path limit is exceeded.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyRemovePrivateAs 1.3.6.1.4.1.4874.2.2.29.1.8.1.25
Remove private AS numbers from AS paths.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyUnsuppressMap 1.3.6.1.4.1.4874.2.2.29.1.8.1.26
The unsuppress route-map name. Routes which are sent to this peer and which match this route-map are not subject to suppression by summary-only aggregates. An empty string means no unsuppress route-map.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerAddressFamilyInboundSoftReconfig 1.3.6.1.4.1.4874.2.2.29.1.8.1.27
Inbound soft-reconfiguration is enabled. If inbound soft-reconfiguration is enabled we keep a copy of each received route before inbound policy was applied.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyResetConnectionType 1.3.6.1.4.1.4874.2.2.29.1.8.1.28
Writing a value to this object causes one individual address family within the session to the peer to be cleared; the value determines what type of clear is executed (hard clear, soft clear in, soft clear out, etc.). Note that hard clearing an address family within a session will bounce the session and thus also affect the other address families in the session. Reading this object has no effect and always returns resetTypeNoop.
Status: current Access: read-create
OBJECT-TYPE    
  JuniBgpResetConnectionType  

juniBgpPeerAddressFamilyRowStatus 1.3.6.1.4.1.4874.2.2.29.1.8.1.29
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniBgpPeerAddressFamilyAsOverride 1.3.6.1.4.1.4874.2.2.29.1.8.1.30
Replace the AS number of the peer by our own AS number in the AS-path attribute in UPDATEs sent to this peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyAllowAsIn 1.3.6.1.4.1.4874.2.2.29.1.8.1.31
The maximum number of times our own AS number is allowed to occur in a received AS-path before that received route is considered to be a loop and therefore rejected.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..10  

juniBgpPeerAddressFamilySendExtendedCommunity 1.3.6.1.4.1.4874.2.2.29.1.8.1.32
Set this object to true(1) in order to send EXTENDED-COMMUNITIES attributes in updates.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyAdvertiseCapPrefixListOrfSend 1.3.6.1.4.1.4874.2.2.29.1.8.1.33
Set this object to true(1) in order to send PREFIX-LIST ORF SEND CAPABILITY in Open Message.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyAdvertiseCapPrefixListOrfReceive 1.3.6.1.4.1.4874.2.2.29.1.8.1.34
Set this object to true(1) in order to send PREFIX-LIST ORF RECEIVE CAPABILITY in Open Message.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyAdvertiseCapPrefixListCiscoOrfSend 1.3.6.1.4.1.4874.2.2.29.1.8.1.35
Set this object to true(1) in order to send PREFIX-LIST-CISCO ORF SEND CAPABILITY in Open Message.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyAdvertiseCapPrefixListCiscoOrfReceive 1.3.6.1.4.1.4874.2.2.29.1.8.1.36
Set this object to true(1) in order to send PREFIX-LIST-CISCO ORF RECEIVE CAPABILITY in Open Message.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyReceivedCapPrefixListOrfSend 1.3.6.1.4.1.4874.2.2.29.1.8.1.37
The peer has sent PREFIX-LIST ORF SEND CAPABILITY to us for this address family.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyReceivedCapPrefixListOrfReceive 1.3.6.1.4.1.4874.2.2.29.1.8.1.38
The peer has sent PREFIX-LIST ORF RECEIVE CAPABILITY to us for this address family.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyReceivedCapPrefixListCiscoOrfSend 1.3.6.1.4.1.4874.2.2.29.1.8.1.39
The peer has sent PREFIX-LIST-CISCO ORF SEND CAPABILITY to us for this address family.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyReceivedCapPrefixListCiscoOrfReceive 1.3.6.1.4.1.4874.2.2.29.1.8.1.40
The peer has sent PREFIX-LIST-CISCO ORF RECEIVE CAPABILITY to us for this address family.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyReceivedOrfEntriesLimit 1.3.6.1.4.1.4874.2.2.29.1.8.1.41
Ignore received ORF entries for this address family if count exceeds this value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerAddressFamilyReceivedPrefixListOrfName 1.3.6.1.4.1.4874.2.2.29.1.8.1.42
The prefix list name containing ORF entries received from the peer for this address family
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerAddressFamilyMaximumPrefixStrict 1.3.6.1.4.1.4874.2.2.29.1.8.1.43
If the juniBgpPeerAddressFamilyInboundSoftReconfig object is set to true then routes which were rejected by inbound policy are stored in memory anyway. The juniBgpPeerAddressFamilyMaximumPrefixStrict object determines whether or not these routes count towards the maximum number of routes from the peer (as configured in juniBgpPeerAddressFamilyRouteLimitWarn and/or juniBgpPeerAddressFamilyRouteLimitReset).
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyUnconfiguredAttributes 1.3.6.1.4.1.4874.2.2.29.1.8.1.44
On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
Status: current Access: read-create
OBJECT-TYPE    
  BITS juniBgpPeerAddressFamilyPeerGroup(0), juniBgpPeerAddressFamilyDefaultOriginate(1), juniBgpPeerAddressFamilyNextHopSelf(2), juniBgpPeerAddressFamilySendCommunity(3), juniBgpPeerAddressFamilyDistributeListIn(4), juniBgpPeerAddressFamilyDistributeListOut(5), juniBgpPeerAddressFamilyPrefixListIn(6), juniBgpPeerAddressFamilyPrefixListOut(7), juniBgpPeerAddressFamilyPrefixTreeIn(8), juniBgpPeerAddressFamilyPrefixTreeOut(9), juniBgpPeerAddressFamilyFilterListIn(10), juniBgpPeerAddressFamilyFilterListOut(11), juniBgpPeerAddressFamilyFilterListWeight(12), juniBgpPeerAddressFamilyFilterListWeightValue(13), juniBgpPeerAddressFamilyRouteMapIn(14), juniBgpPeerAddressFamilyRouteMapOut(15), juniBgpPeerAddressFamilyRouteReflectorClient(16), juniBgpPeerAddressFamilyRouteLimitWarn(17), juniBgpPeerAddressFamilyRouteLimitReset(18), juniBgpPeerAddressFamilyRouteLimitWarnOnly(19), juniBgpPeerAddressFamilyRemovePrivateAs(20), juniBgpPeerAddressFamilyUnsuppressMap(21), juniBgpPeerAddressFamilyInboundSoftReconfig(22), juniBgpPeerAddressFamilyAsOverride(23), juniBgpPeerAddressFamilyAllowAsIn(24), juniBgpPeerAddressFamilySendExtendedCommunity(25), juniBgpPeerAddressFamilyAdvertiseCapPrefixListOrfSend(26), juniBgpPeerAddressFamilyAdvertiseCapPrefixListOrfReceive(27), juniBgpPeerAddressFamilyAdvertiseCapPrefixListCiscoOrfSend(28), juniBgpPeerAddressFamilyAdvertiseCapPrefixListCiscoOrfReceive(29), juniBgpPeerAddressFamilyReceivedOrfEntriesLimit(30), juniBgpPeerAddressFamilyMaximumPrefixStrict(31), juniBgpPeerAddressFamilySendLabel(32), juniBgpPeerAddressFamilyDefaultOriginateRouteMap(33), juniBgpPeerAddressFamilyNextHopUnchanged(34)  

juniBgpPeerAddressFamilySendLabel 1.3.6.1.4.1.4874.2.2.29.1.8.1.45
Send labeled prefixes to this peer for this address-family.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyDefaultOriginateRouteMap 1.3.6.1.4.1.4874.2.2.29.1.8.1.46
The route-map to apply to the default route which is advertised to this peer as a result of setting juniBgpPeerAddressFamilyDefaultOriginate to true. An empty string means that no route-map is applied.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerAddressFamilySentCapabilityGracefulRestart 1.3.6.1.4.1.4874.2.2.29.1.8.1.47
Value true(1) means that an AFI-SAFI block for this address-family was included in the graceful-restart capability which we sent to this peer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyReceivedCapabilityGracefulRestart 1.3.6.1.4.1.4874.2.2.29.1.8.1.48
Value true(1) means that an AFI-SAFI block for this address-family was included in the graceful-restart capability which we received from this peer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilySentForwardingStatePreserved 1.3.6.1.4.1.4874.2.2.29.1.8.1.49
Value true(1) indicates that the OPEN message most recently sent to this peer contained the graceful-restart capability which included an AFI-SAFI block for this address-family with the Forwarding-State (F) bit in the Flags for Address Family field set to one (this indicates that forwarding state has been preserved for the address family during the previous restart).
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyReceivedForwardingStatePreserved 1.3.6.1.4.1.4874.2.2.29.1.8.1.50
Value true(1) indicates that the OPEN message most recently received from this peer contained the graceful-restart capability which included an AFI-SAFI block for this address-family with the Forwarding-State (F) bit in the Flags for Address Family field set to one (this indicates that the peer preserved forwarding state for the address family during the previous restart).
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilySentEndOfRibMarker 1.3.6.1.4.1.4874.2.2.29.1.8.1.51
Value true(1) indicates that we have sent an End-of-RIB marker for this address-family to this peer since the session became established.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyReceivedEndOfRibMarker 1.3.6.1.4.1.4874.2.2.29.1.8.1.52
Value true(1) indicates that we have received an End-of-RIB marker for this address-family from this peer since the session became established.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyWaitingForEndOfRibBeforeFlushStaleRoutes 1.3.6.1.4.1.4874.2.2.29.1.8.1.53
Value true(1) indicates that we are still waiting for an End-of-RIB marker from this peer before flushing all remaining stale routes from the address-family.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyWaitingForEndOfRibBeforePathSelection 1.3.6.1.4.1.4874.2.2.29.1.8.1.54
Value true(1) indicates that we are still waiting for an End-of-RIB marker from this peer before we stop deferring path selection for this address-family.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyNextHopUnchanged 1.3.6.1.4.1.4874.2.2.29.1.8.1.55
Set this object to true(1) in order to always advertise the the next-hop unchanged to this peer for this address-family.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyConditionalAdvTable 1.3.6.1.4.1.4874.2.2.29.1.30
The Juniper BGP Peer Address Family Conditional Advertisement Table describes the BGP conditional advertisement attributes in an Address Family for a peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpPeerAddressFamilyConditionalAdvEntry

juniBgpPeerAddressFamilyConditionalAdvEntry 1.3.6.1.4.1.4874.2.2.29.1.30.1
The Juniper BGP Peer Address Family Conditional Advertisement Entry describes a specific conditional advertisement entry in Address Family for a peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpPeerAddressFamilyConditionalAdvEntry  

juniBgpPeerAddressFamilyConditionalAdvAdvertiseMap 1.3.6.1.4.1.4874.2.2.29.1.30.1.1
The route-map for conditional advertisement.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpAdvertiseMapName  

juniBgpPeerAddressFamilyConditionalAdvConditionMap 1.3.6.1.4.1.4874.2.2.29.1.30.1.2
The condition-map to apply for this conditional advertisement entry.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

juniBgpPeerAddressFamilyConditionalAdvIsExistMap 1.3.6.1.4.1.4874.2.2.29.1.30.1.3
Set this value to true(1) if the condition-map specified should be applied as an exist-map. If the condition-map should be applied as a non-exist-map, set it to false(2).
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerAddressFamilyConditionalAdvSequenceNum 1.3.6.1.4.1.4874.2.2.29.1.30.1.4
The sequence number of this conditional advertisement entry.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

juniBgpPeerAddressFamilyConditionalAdvStatus 1.3.6.1.4.1.4874.2.2.29.1.30.1.5
This value will be advertise(1) if the status of this advertise-map is evaluated as advertise based on the condition-map. Otherwise it is withdraw(2).
Status: current Access: read-only
OBJECT-TYPE    
  JuniBgpConditionalAdvStatus  

juniBgpPeerAddressFamilyConditionalAdvRowStatus 1.3.6.1.4.1.4874.2.2.29.1.30.1.6
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo, destroy
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniBgpPeerGroupTable 1.3.6.1.4.1.4874.2.2.29.1.9
The Juniper BGP Peer Group Table describes the BGP-specific characteristics of peer groups.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpPeerGroupEntry

juniBgpPeerGroupEntry 1.3.6.1.4.1.4874.2.2.29.1.9.1
The BGP Peer Group Entry describes BGP-specific characteristics of one peer group.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpPeerGroupEntry  

juniBgpPeerGroupVrfName 1.3.6.1.4.1.4874.2.2.29.1.9.1.1
The name of the VPN Routing Forwarding (VRF) instance in which this peer-group is configured. The empty string indicates that this peer-group is not in a VRF.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniVrfName  

juniBgpPeerGroupGroupName 1.3.6.1.4.1.4874.2.2.29.1.9.1.2
The name of the Peer group this instance configures.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAdminStatus 1.3.6.1.4.1.4874.2.2.29.1.9.1.3
The desired state of the BGP connection. A transition from 'stop' to 'start' will cause the BGP Start Event to be generated. A transition from 'start' to 'stop' will cause the BGP Stop Event to be generated. This parameter can be used to restart BGP peer connections. Care should be used in providing write access to this object without adequate authentication.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER stop(1), start(2)  

juniBgpPeerGroupRemoteAsNumber 1.3.6.1.4.1.4874.2.2.29.1.9.1.4
Deprecated. The peer's autonomous system number. This object has been replaced by juniBgpPeerGroupFourOctetRemoteAsNumber. It is still possible to get and set this object, but if the actual remote AS number is greater than 65535, getting this object returns 23456 (AS-TRANS).
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpPeerGroupRetryInterval 1.3.6.1.4.1.4874.2.2.29.1.9.1.5
Time interval in seconds for the ConnectRetry timer. The suggested value for this timer is 120 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

juniBgpPeerGroupConfigHoldTime 1.3.6.1.4.1.4874.2.2.29.1.9.1.6
Time interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an OPEN message received from the peer when determining the Hold Time (bgpPeerHoldTime) with the peer. This value must not be less than three seconds if it is not zero (0) in which case the Hold Time is NOT to be established with the peer. The suggested value for this timer is 90 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0 | 3..65535  

juniBgpPeerGroupConfigKeepAliveInterval 1.3.6.1.4.1.4874.2.2.29.1.9.1.7
Time interval in seconds for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages' frequency relative to the value specified in bgpPeerHoldTimeConfigured; the actual time interval for the KEEPALIVE messages is indicated by bgpPeerKeepAlive. A reasonable maximum value for this timer would be configured to be one third of that of bgpPeerHoldTimeConfigured. If the value of this object is zero (0), no periodical KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..21845  

juniBgpPeerGroupAsOriginationInterval 1.3.6.1.4.1.4874.2.2.29.1.9.1.8
Time interval in seconds for the MinASOriginationInterval timer. The suggested value for this timer is 10 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

juniBgpPeerGroupAdvertisementInterval 1.3.6.1.4.1.4874.2.2.29.1.9.1.9
Time interval in seconds for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

juniBgpPeerGroupDescription 1.3.6.1.4.1.4874.2.2.29.1.9.1.10
Peer textual description.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..80)  

juniBgpPeerGroupWeight 1.3.6.1.4.1.4874.2.2.29.1.9.1.11
The weight assigned to routes learned from peer.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerGroupEbgpMultihop 1.3.6.1.4.1.4874.2.2.29.1.9.1.12
The EBGP multihop is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupEbgpMultihopTtl 1.3.6.1.4.1.4874.2.2.29.1.9.1.13
Maximum number of hops to the external peer (only relevant if EBGP multihop turned on).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..255  

juniBgpPeerGroupUpdateSource 1.3.6.1.4.1.4874.2.2.29.1.9.1.14
The source IP address for peer connections.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

juniBgpPeerGroupMd5Password 1.3.6.1.4.1.4874.2.2.29.1.9.1.15
The password for MD5 authentication. Reading this object always results in an OCTET STRING of length zero.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

juniBgpPeerGroupMaxUpdateSize 1.3.6.1.4.1.4874.2.2.29.1.9.1.16
The maximum size in bytes of transmitted UPDATE messages.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerGroupResetConnectionType 1.3.6.1.4.1.4874.2.2.29.1.9.1.17
Writing a value to this object causes the sessions to all peers in the peer-group to be cleared; the value determines what type of clear is executed (hard clear, soft clear in, soft clear out, etc.). Reading this object has no effect and always returns resetTypeNoop.
Status: current Access: read-create
OBJECT-TYPE    
  JuniBgpResetConnectionType  

juniBgpPeerGroupRowStatus 1.3.6.1.4.1.4874.2.2.29.1.9.1.18
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniBgpPeerGroupLocalAsNumber 1.3.6.1.4.1.4874.2.2.29.1.9.1.19
Deprecated. The local autonomous system number to be used for members. of this peer-group. Value zero (0) means that the global local automous system number (as specified in the object juniBgpPeerGroupLocalAsNumber) is used. This object has been replaced by juniBgpPeerGroupFourOctetLocalAsNumber. It is still possible to get and set this object, but if the actual local AS number is greater than 65535, getting this object returns AS-TRANS (23456).
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpPeerGroupFourOctetRemoteAsNumber 1.3.6.1.4.1.4874.2.2.29.1.9.1.20
The peer's four-octet autonomous system number.
Status: current Access: read-create
OBJECT-TYPE    
  JuniBgpFourOctetAsNumber  

juniBgpPeerGroupFourOctetLocalAsNumber 1.3.6.1.4.1.4874.2.2.29.1.9.1.21
The four-octet local autonomous system number to be used for this peer. Value zero (0) means that the global local automous system number (as specified in the object juniBgpPeerGroupFourOctetLocalAsNumber) is used.
Status: current Access: read-create
OBJECT-TYPE    
  JuniBgpFourOctetAsNumber  

juniBgpPeerGroupShouldAdvertiseCapabilitiesOption 1.3.6.1.4.1.4874.2.2.29.1.9.1.22
Set this object to true if the capabilities option should be included in OPEN messages sent to this peer. Even if this object is set to true, BGP may decide not to include the capabilities option in OPEN messages sent to this peer (for example when it is detected that the peer does not support capability negotiation). The juniBgpPeerSentCapabilitiesOption can be used to determine whether or not the OPEN message sent to the peer actually contained the capabilities option.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupShouldAdvertiseCapabilityRouteRefresh 1.3.6.1.4.1.4874.2.2.29.1.9.1.23
Set this object to true if the route-refresh capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the route-refresh capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the route-refresh capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityRouteRefresh can be used to determine whether or not the capability was actually advertised to the peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupShouldAdvertiseCapabilityRouteRefreshCisco 1.3.6.1.4.1.4874.2.2.29.1.9.1.24
Set this object to true if the route-refresh-cisco capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the route-refresh-cisco capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the route-refresh-cisco capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityRouteRefreshCisco can be used to determine whether or not the capability was actually advertised to the peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupShouldAdvertiseCapabilityFourOctetAsNumbers 1.3.6.1.4.1.4874.2.2.29.1.9.1.25
Set this object to true if the four-octet-as-numbers capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the four-octet-as-numbers capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the four-octet-as-numbers capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityFourOctetAsNumbers can be used to determine whether or not the capability was actually advertised to the peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupShouldAdvertiseCapabilityDynamicCapabilityNeg 1.3.6.1.4.1.4874.2.2.29.1.9.1.26
Set this object to true if the dynamic-capability-negotiation capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the dynamic-capability-negotiation capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the dynamic-capability-negotiation capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityDynamicCapabilityNeg can be used to determine whether or not the capability was actually advertised to the peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupUnconfiguredAttributes 1.3.6.1.4.1.4874.2.2.29.1.9.1.27
On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
Status: current Access: read-create
OBJECT-TYPE    
  BITS juniBgpPeerGroupAdminStatus(0), juniBgpPeerGroupRetryInterval(1), juniBgpPeerGroupConfigHoldTime(2), juniBgpPeerGroupConfigKeepAliveInterval(3), juniBgpPeerGroupAsOriginationInterval(4), juniBgpPeerGroupAdvertisementInterval(5), juniBgpPeerGroupDescription(6), juniBgpPeerGroupWeight(7), juniBgpPeerGroupEbgpMultihop(8), juniBgpPeerGroupEbgpMultihopTtl(9), juniBgpPeerGroupUpdateSource(10), juniBgpPeerGroupMd5Password(11), juniBgpPeerGroupMaxUpdateSize(12), juniBgpPeerGroupFourOctetRemoteAsNumber(13), juniBgpPeerGroupFourOctetLocalAsNumber(14), juniBgpPeerGroupShouldAdvertiseCapabilitiesOption(15), juniBgpPeerGroupShouldAdvertiseCapabilityRouteRefresh(16), juniBgpPeerGroupShouldAdvertiseCapabilityRouteRefreshCisco(17), juniBgpPeerGroupShouldAdvertiseCapabilityFourOctetAsNumbers(18), juniBgpPeerGroupShouldAdvertiseCapabilityDynamicCapabilityNeg(19), juniBgpPeerGroupSiteOfOrigin(20), juniBgpPeerGroupLenient(21), juniBgpPeerGroupShouldAdvertiseCapabilityOldDynamicCapabilityNeg(22), juniBgpPeerGroupPassive(23), juniBgpPeerGroupConfiguredPeerType(24), juniBgpPeerGroupAllowAccessListName(25), juniBgpPeerGroupAllowMaxPeers(26), juniBgpPeerGroupShouldAdvertiseCapabilityGracefulRestart(27), juniBgpPeerGroupGracefulRestartRestartTime(28), juniBgpPeerGroupGracefulRestartStalePathsTime(29), juniBgpPeerGroupBfdEnabled(30), juniBgpPeerGroupBfdMinTransmitInterval(31), juniBgpPeerGroupBfdMinReceiveInterval(32), juniBgpPeerGroupBfdMultiplier(33), juniBgpPeerGroupIbgpSinglehop(34)  

juniBgpPeerGroupSiteOfOrigin 1.3.6.1.4.1.4874.2.2.29.1.9.1.28
The site-of-origin. This site-of-origin is added to the extended communities for all routes received from the peer. When sending routes to this peer-group all routes with this extended community are filtered. The null extended community (all 8 bytes zero) means that no site-of-origin is configured for this peer. It is not allowed to set this object to any extended community other than a site-of-origin type of extended community or null.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(8)  

juniBgpPeerGroupLenient 1.3.6.1.4.1.4874.2.2.29.1.9.1.29
Enable Lenient behavior for member peers so that they are more tolerant of finite state machine errors and malformed messages received from the remote peer and avoid terminating the peer session whenever possible.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupShouldAdvertiseCapabilityOldDynamicCapabilityNeg 1.3.6.1.4.1.4874.2.2.29.1.9.1.30
Set this object to true if the deprecated-dynamic-capability- negotiation capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the deprecated-dynamic-capability-negotiation capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the deprecated-dynamic-capability-negotiation capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityOldDynamicCapabilityNeg can be used to determine whether or not the capability was actually advertised to the peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupPassive 1.3.6.1.4.1.4874.2.2.29.1.9.1.31
Set this object to true(1) to make members of this peer-group passive.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupConfiguredPeerType 1.3.6.1.4.1.4874.2.2.29.1.9.1.32
The type of the members of the peer-group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER peerTypeNotConfigured(0), peerTypeInternal(1), peerTypeExternal(2), peerTypeConfederation(3)  

juniBgpPeerGroupAllowAccessListName 1.3.6.1.4.1.4874.2.2.29.1.9.1.33
The name of the access-list for promiscuous peers. When an incoming connection arrives whose remote address matches this access-list the connection is accepted and a dynamic peer is created. An empty string means that promiscuous peers are disabled for this peer-group.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAllowMaxPeers 1.3.6.1.4.1.4874.2.2.29.1.9.1.34
The maximum number of dynamic peers for this peer-group. Zero means that there is no limit.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerGroupCurrentDynamicPeerCount 1.3.6.1.4.1.4874.2.2.29.1.9.1.35
The current number of dynamic peers for this peer-group.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerGroupHighWaterMarkDynamicPeerCount 1.3.6.1.4.1.4874.2.2.29.1.9.1.36
The high water mark for the number of dynamic peers for this peer-group.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerGroupRejectedDynamicPeerCount 1.3.6.1.4.1.4874.2.2.29.1.9.1.37
The number of connection attempts for dynamic peers that were rejected because the number number of dynamic peers was reached.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerGroupShouldAdvertiseCapabilityGracefulRestart 1.3.6.1.4.1.4874.2.2.29.1.9.1.38
Set this object to true if the graceful-restart capability should be advertised to all members of the peer-group.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupGracefulRestartRestartTime 1.3.6.1.4.1.4874.2.2.29.1.9.1.39
The restart-time advertised in the graceful-restart capability sent to members of this peer-group. This is the estimated time (in seconds) it will take for the BGP session to be re-established after a restart. This can be used to speed up routing convergence by the peer in case that this BGP speaker does not come back after a restart. This value (if configured) overrides the global value configured in juniBgpGracefulRestartRestartTime.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..3600  

juniBgpPeerGroupGracefulRestartStalePathsTime 1.3.6.1.4.1.4874.2.2.29.1.9.1.40
The maximum amount of time in seconds we keep stale routes after the session to a member of this peer-group goes down. This value (if configured) overrides the global value configured in juniBgpGracefulRestartStalePathsTime.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..3600  

juniBgpPeerGroupBfdEnabled 1.3.6.1.4.1.4874.2.2.29.1.9.1.41
Value true(1) the BFD is enabled for this peer-group.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupBfdMinTransmitInterval 1.3.6.1.4.1.4874.2.2.29.1.9.1.42
The minimum interval (in milliseconds) between BFD packets sent to the remote BFD speaker. In other words, it specifies the maximum rate at which we are willing to send BFD packets.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 100..65535  

juniBgpPeerGroupBfdMinReceiveInterval 1.3.6.1.4.1.4874.2.2.29.1.9.1.43
The minimum interval (in milliseconds) between BFD packets received from the remote BFD speaker. In other words, it specifies the maximum rate at which we are willing to receive BFD packets.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 100..65535  

juniBgpPeerGroupBfdMultiplier 1.3.6.1.4.1.4874.2.2.29.1.9.1.44
How many BFD packets can be missed before the BFD session is declared down.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..255  

juniBgpPeerGroupIbgpSinglehop 1.3.6.1.4.1.4874.2.2.29.1.9.1.45
The IBGP single-hop is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyTable 1.3.6.1.4.1.4874.2.2.29.1.10
The Juniper BGP Peer Group Address Family Table describes the BGP-specific attributes of an Address Family for a peer group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpPeerGroupAddressFamilyEntry

juniBgpPeerGroupAddressFamilyEntry 1.3.6.1.4.1.4874.2.2.29.1.10.1
The BGP Peer Group Address Family Entry describes.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpPeerGroupAddressFamilyEntry  

juniBgpPeerGroupAddressFamilyVrfName 1.3.6.1.4.1.4874.2.2.29.1.10.1.1
The name of the VPN Routing Forwarding (VRF) instance in which this peer-group is configured. The empty string indicates that this peer-group is not in a VRF.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniVrfName  

juniBgpPeerGroupAddressFamilyAfi 1.3.6.1.4.1.4874.2.2.29.1.10.1.2
The AFI of the address-family in which this peer-group is configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpAfi  

juniBgpPeerGroupAddressFamilySafi 1.3.6.1.4.1.4874.2.2.29.1.10.1.3
The SAFI of the address-family in which this peer-group is configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpSafi  

juniBgpPeerGroupGroupAddressFamilyGroupName 1.3.6.1.4.1.4874.2.2.29.1.10.1.4
The name of the Peer group this instance configures.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAddressFamilyDefaultOriginate 1.3.6.1.4.1.4874.2.2.29.1.10.1.5
Set this object to true(1) in order to advertise a default route to this peer, if present.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyNextHopSelf 1.3.6.1.4.1.4874.2.2.29.1.10.1.6
Set this object to true(1) in order to always advertise this router as the next hop.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilySendCommunity 1.3.6.1.4.1.4874.2.2.29.1.10.1.7
Set this object to true(1) in order to send COMMUNITIES attributes in updates.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyDistributeListIn 1.3.6.1.4.1.4874.2.2.29.1.10.1.8
The inbound distribute IP access list name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAddressFamilyDistributeListOut 1.3.6.1.4.1.4874.2.2.29.1.10.1.9
The outbound distribute IP access list name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAddressFamilyPrefixListIn 1.3.6.1.4.1.4874.2.2.29.1.10.1.10
The inbound IP prefix list name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAddressFamilyPrefixListOut 1.3.6.1.4.1.4874.2.2.29.1.10.1.11
The outbound IP prefix list name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAddressFamilyPrefixTreeIn 1.3.6.1.4.1.4874.2.2.29.1.10.1.12
The inbound IP prefix tree name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAddressFamilyPrefixTreeOut 1.3.6.1.4.1.4874.2.2.29.1.10.1.13
The outbound IP prefix tree name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAddressFamilyFilterListIn 1.3.6.1.4.1.4874.2.2.29.1.10.1.14
The inbound filter AS path list name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAddressFamilyFilterListOut 1.3.6.1.4.1.4874.2.2.29.1.10.1.15
The outbound filter AS path list name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAddressFamilyFilterListWeight 1.3.6.1.4.1.4874.2.2.29.1.10.1.16
The weight filter AS path list name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAddressFamilyFilterListWeightValue 1.3.6.1.4.1.4874.2.2.29.1.10.1.17
The weight to apply on weight filter list matches.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerGroupAddressFamilyRouteMapIn 1.3.6.1.4.1.4874.2.2.29.1.10.1.18
The inbound route-map name. An empty string means no inbound route-map.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAddressFamilyRouteMapOut 1.3.6.1.4.1.4874.2.2.29.1.10.1.19
The outbound route-map name. An empty string means no outbound route-map.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAddressFamilyRouteReflectorClient 1.3.6.1.4.1.4874.2.2.29.1.10.1.20
The peer is a route reflector client.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyRouteLimitWarn 1.3.6.1.4.1.4874.2.2.29.1.10.1.21
Log a warning if pathCount exceeds this value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerGroupAddressFamilyRouteLimitReset 1.3.6.1.4.1.4874.2.2.29.1.10.1.22
Reset connection is pathCount exceeds this value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpPeerGroupAddressFamilyRouteLimitWarnOnly 1.3.6.1.4.1.4874.2.2.29.1.10.1.23
Warn, but do not reset, if the path limit is exceeded.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyRemovePrivateAs 1.3.6.1.4.1.4874.2.2.29.1.10.1.24
Remove private AS numbers from AS paths.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyUnsuppressMap 1.3.6.1.4.1.4874.2.2.29.1.10.1.25
The unsuppress route-map name. Routes which are sent to this peer and which match this route-map are not subject to suppression by summary-only aggregates. An empty string means no unsuppress route-map.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAddressFamilyInboundSoftReconfig 1.3.6.1.4.1.4874.2.2.29.1.10.1.26
Inbound soft-reconfiguration is enabled. If inbound soft-reconfiguration is enabled we keep a copy of each received route before inbound policy was applied.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyResetConnectionType 1.3.6.1.4.1.4874.2.2.29.1.10.1.27
Writing a value to this object causes one individual address family within the sessions to all peers in the peer-group to be cleared; the value determines what type of clear is executed (hard clear, soft clear in, soft clear out, etc.). Note that hard clearing an address family within a session will bounce the session and thus also affect the other address families in the session. Reading this object has no effect and always returns resetTypeNoop.
Status: current Access: read-create
OBJECT-TYPE    
  JuniBgpResetConnectionType  

juniBgpPeerGroupAddressFamilyRowStatus 1.3.6.1.4.1.4874.2.2.29.1.10.1.28
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniBgpPeerGroupAddressFamilyAsOverride 1.3.6.1.4.1.4874.2.2.29.1.10.1.29
Replace the AS number of the peer by our own AS number in the AS-path attribute in UPDATEs sent to this peer-group.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyAllowAsIn 1.3.6.1.4.1.4874.2.2.29.1.10.1.30
The maximum number of times our own AS number is allowed to occur in a received AS-path before that received route is considered to be a loop and therefore rejected.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..10  

juniBgpPeerGroupAddressFamilySendExtendedCommunity 1.3.6.1.4.1.4874.2.2.29.1.10.1.31
Set this object to true(1) in order to send EXTENDED-COMMUNITIES attributes in updates.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyAdvertiseCapPrefixListOrfSend 1.3.6.1.4.1.4874.2.2.29.1.10.1.32
Set this object to true(1) in order to send PREFIX-LIST ORF SEND CAPABILITY in Open Message.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyAdvertiseCapPrefixListCiscoOrfSend 1.3.6.1.4.1.4874.2.2.29.1.10.1.33
Set this object to true(1) in order to send PREFIX-LIST-CISCO ORF SEND CAPABILITY in Open Message.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyMaximumPrefixStrict 1.3.6.1.4.1.4874.2.2.29.1.10.1.34
If the juniBgpPeerGroupAddressFamilyInboundSoftReconfig object is set to true then routes which were rejected by inbound policy are stored in memory anyway. The juniBgpPeerGroupAddressFamilyMaximumPrefixStrict object determines whether or not these routes count towards the maximum number of routes from the peer-group members (as configured in juniBgpPeerGroupAddressFamilyRouteLimitWarn and/or juniBgpPeerGroupAddressFamilyRouteLimitReset).
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyUnconfiguredAttributes 1.3.6.1.4.1.4874.2.2.29.1.10.1.35
On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
Status: current Access: read-create
OBJECT-TYPE    
  BITS juniBgpPeerGroupAddressFamilyDefaultOriginate(0), juniBgpPeerGroupAddressFamilyNextHopSelf(1), juniBgpPeerGroupAddressFamilySendCommunity(2), juniBgpPeerGroupAddressFamilyDistributeListIn(3), juniBgpPeerGroupAddressFamilyDistributeListOut(4), juniBgpPeerGroupAddressFamilyPrefixListIn(5), juniBgpPeerGroupAddressFamilyPrefixListOut(6), juniBgpPeerGroupAddressFamilyPrefixTreeIn(7), juniBgpPeerGroupAddressFamilyPrefixTreeOut(8), juniBgpPeerGroupAddressFamilyFilterListIn(9), juniBgpPeerGroupAddressFamilyFilterListOut(10), juniBgpPeerGroupAddressFamilyFilterListWeight(11), juniBgpPeerGroupAddressFamilyFilterListWeightValue(12), juniBgpPeerGroupAddressFamilyRouteMapIn(13), juniBgpPeerGroupAddressFamilyRouteMapOut(14), juniBgpPeerGroupAddressFamilyRouteReflectorClient(15), juniBgpPeerGroupAddressFamilyRouteLimitWarn(16), juniBgpPeerGroupAddressFamilyRouteLimitReset(17), juniBgpPeerGroupAddressFamilyRouteLimitWarnOnly(18), juniBgpPeerGroupAddressFamilyRemovePrivateAs(19), juniBgpPeerGroupAddressFamilyUnsuppressMap(20), juniBgpPeerGroupAddressFamilyInboundSoftReconfig(21), juniBgpPeerGroupAddressFamilyAsOverride(22), juniBgpPeerGroupAddressFamilyAllowAsIn(23), juniBgpPeerGroupAddressFamilySendExtendedCommunity(24), juniBgpPeerGroupAddressFamilyAdvertiseCapPrefixListOrfSend(25), juniBgpPeerGroupAddressFamilyAdvertiseCapPrefixListOrfCiscoSend(26), juniBgpPeerGroupAddressFamilyMaximumPrefixStrict(27), juniBgpPeerGroupAddressFamilySendLabel(28), juniBgpPeerGroupAddressFamilyDefaultOriginateRouteMap(29), juniBgpPeerGroupAddressFamilyNextHopUnchanged(30)  

juniBgpPeerGroupAddressFamilySendLabel 1.3.6.1.4.1.4874.2.2.29.1.10.1.36
Send labeled prefixes to this peer for this address-family.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyDefaultOriginateRouteMap 1.3.6.1.4.1.4874.2.2.29.1.10.1.37
The route-map to apply to the default route which is advertised to this peer-group as a result of setting juniBgpPeerGroupAddressFamilyDefaultOriginate to true. An empty string means that no route-map is applied.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpPeerGroupAddressFamilyNextHopUnchanged 1.3.6.1.4.1.4874.2.2.29.1.10.1.38
Set this object to true(1) in order to always advertise the next-hop unchanged to this peer-group in this address-family.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyConditionalAdvTable 1.3.6.1.4.1.4874.2.2.29.1.31
The Juniper BGP Peer Group Address Family Conditional Advertisement Table describes the BGP conditional advertisement attributes in an Address Family for a peer-group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpPeerGroupAddressFamilyConditionalAdvEntry

juniBgpPeerGroupAddressFamilyConditionalAdvEntry 1.3.6.1.4.1.4874.2.2.29.1.31.1
The Juniper BGP Peer Group Address Family Conditional Advertisement Entry describes a specific conditional advertisement entry in an Address Family for a peer-group.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpPeerGroupAddressFamilyConditionalAdvEntry  

juniBgpPeerGroupAddressFamilyConditionalAdvAdvertiseMap 1.3.6.1.4.1.4874.2.2.29.1.31.1.1
The route-map for conditional advertisement.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpAdvertiseMapName  

juniBgpPeerGroupAddressFamilyConditionalAdvConditionMap 1.3.6.1.4.1.4874.2.2.29.1.31.1.2
The condition-map to apply for this conditional advertisement entry.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

juniBgpPeerGroupAddressFamilyConditionalAdvIsExistMap 1.3.6.1.4.1.4874.2.2.29.1.31.1.3
Set this value to true(1) if the condition-map specified should be applied as an exist-map. If the condition-map should be applied as a non-exist-map, set it to false(2).
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpPeerGroupAddressFamilyConditionalAdvSequenceNum 1.3.6.1.4.1.4874.2.2.29.1.31.1.4
The sequence number of this conditional advertisement entry.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

juniBgpPeerGroupAddressFamilyConditionalAdvStatus 1.3.6.1.4.1.4874.2.2.29.1.31.1.5
This value will be advertise(1) if the status of this advertise-map is evaluated as advertise based on the condition-map. Otherwise it is withdraw(2).
Status: current Access: read-only
OBJECT-TYPE    
  JuniBgpConditionalAdvStatus  

juniBgpPeerGroupAddressFamilyConditionalAdvRowStatus 1.3.6.1.4.1.4874.2.2.29.1.31.1.6
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo, destroy
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniBgpNetworkTable 1.3.6.1.4.1.4874.2.2.29.1.16
The BGP Network Table controls what networks are originated by this BGP router.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpNetworkEntry

juniBgpNetworkEntry 1.3.6.1.4.1.4874.2.2.29.1.16.1
An instance in the list of networks originated by this BGP router.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpNetworkEntry  

juniBgpNetworkVrfName 1.3.6.1.4.1.4874.2.2.29.1.16.1.1
The name of the VPN Routing Forwarding (VRF) instance in which this network is configured. The empty string indicates that this network is not in a VRF.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniVrfName  

juniBgpNetworkAfi 1.3.6.1.4.1.4874.2.2.29.1.16.1.2
The AFI of the address-family in which this network is configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpAfi  

juniBgpNetworkSafi 1.3.6.1.4.1.4874.2.2.29.1.16.1.3
The SAFI of the address-family in which this network is configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpSafi  

juniBgpNetworkIpAddrPrefix 1.3.6.1.4.1.4874.2.2.29.1.16.1.4
An IP address prefix in the Network Layer Reachability Information field. This object is an IP address containing the prefix with length specified by bgpRouteIpAddrPrefixLen. Any bits beyond the length specified by bgpRouteIpAddrPrefixLen are zeroed.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniBgpNetworkIpAddrPrefixLen 1.3.6.1.4.1.4874.2.2.29.1.16.1.5
Length in bits of the IP address prefix in the Network Layer Reachability Information field.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..32  

juniBgpNetworkBackdoor 1.3.6.1.4.1.4874.2.2.29.1.16.1.6
Set this object to true(1) in order to enable BGP backdoor in this network. This object can only be set at row creation.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpNetworkRowStatus 1.3.6.1.4.1.4874.2.2.29.1.16.1.7
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniBgpNetworkWeightSpecified 1.3.6.1.4.1.4874.2.2.29.1.16.1.8
If this object is set to true(1) then the BGP weight of this network is set to the value specified in juniBgpNetworkWeightValue. This object can only be set at row creation.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpNetworkWeight 1.3.6.1.4.1.4874.2.2.29.1.16.1.9
If juniBgpNetworkWeight specified is set to true(1) then this object specifies the weight of the network. Otherwise the weight of the network is determined by the IGP metric of the prefix. This object can only be set at row creation.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpNetworkRouteMap 1.3.6.1.4.1.4874.2.2.29.1.16.1.10
The name of the route-map used to set the path attributes of this network. A zero length route-map name means don't use a route-map for this. This object can only be set at row creation.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpNetworkUnconfiguredAttributes 1.3.6.1.4.1.4874.2.2.29.1.16.1.11
On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
Status: current Access: read-create
OBJECT-TYPE    
  BITS juniBgpNetworkBackdoor(0), juniBgpNetworkWeight(1), juniBgpNetworkRouteMap(2)  

juniBgpAggregateTable 1.3.6.1.4.1.4874.2.2.29.1.17
The BGP Aggregate Table controls the consolidation of route information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpAggregateEntry

juniBgpAggregateEntry 1.3.6.1.4.1.4874.2.2.29.1.17.1
An instance in the list of route aggregation.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpAggregateEntry  

juniBgpAggregateVrfName 1.3.6.1.4.1.4874.2.2.29.1.17.1.1
The name of the VPN Routing Forwarding (VRF) instance in which this aggregate is configured. The empty string indicates that this aggregate is not in a VRF.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniVrfName  

juniBgpAggregateAfi 1.3.6.1.4.1.4874.2.2.29.1.17.1.2
The AFI of the address-family in which this aggregate is configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpAfi  

juniBgpAggregateSafi 1.3.6.1.4.1.4874.2.2.29.1.17.1.3
The SAFI of the address-family in which this aggregate is configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpSafi  

juniBgpAggregateIpAddrPrefix 1.3.6.1.4.1.4874.2.2.29.1.17.1.4
An IP address prefix in the Network Layer Reachability Information field. This object is an IP address containing the prefix with length specified by bgpRouteIpAddrPrefixLen. Any bits beyond the length specified by bgpRouteIpAddrPrefixLen are zeroed.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniBgpAggregateIpAddrPrefixLen 1.3.6.1.4.1.4874.2.2.29.1.17.1.5
Length in bits of the IP address prefix in the Network Layer Reachability Information field.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..32  

juniBgpAggregateAsSet 1.3.6.1.4.1.4874.2.2.29.1.17.1.6
Set this object to true(1) in order to generate AS_set path information by creating an aggregate entry that consists of all elements contained in all paths that are being summarized. This object can only be set at row creation.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpAggregateSummaryOnly 1.3.6.1.4.1.4874.2.2.29.1.17.1.7
Set this object to true(1) in order to filter specific routes from updates. By doing that, advertisements of more specific routes will be suppressed to all neighbors. This object can only be set at row creation.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpAggregateAttributeMap 1.3.6.1.4.1.4874.2.2.29.1.17.1.8
The name of the route-map used to set the attributes of the aggregate An empty string means no route-map for this purpose.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpAggregateAdvertiseMap 1.3.6.1.4.1.4874.2.2.29.1.17.1.9
The name of the route-map used to select routes covered by the aggregate (for as-set aggregates the path attributes of the aggregate route are created by summarizing the path attributes of the covered routes). An empty string means no route-map for this purpose.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpAggregateRowStatus 1.3.6.1.4.1.4874.2.2.29.1.17.1.10
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniBgpAggregateSuppressMap 1.3.6.1.4.1.4874.2.2.29.1.17.1.11
The suppress route-map name. If a suppress route-map has been specified, all routes which are covered by the aggregate and which match the suppress route-map are suppressed. An empty string means no inbound route-map.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpAggregateUnconfiguredAttributes 1.3.6.1.4.1.4874.2.2.29.1.17.1.12
On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
Status: current Access: read-create
OBJECT-TYPE    
  BITS juniBgpAggregateAsSet(0), juniBgpAggregateSummaryOnly(1), juniBgpAggregateAttributeMap(2), juniBgpAggregateAdvertiseMap(3), juniBgpAggregateSuppressMap(4)  

juniBgpVrfTable 1.3.6.1.4.1.4874.2.2.29.1.18
The Juniper BGP VRF Table describes the BGP-specific characteristics of a VPN routing forwarding instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpVrfEntry

juniBgpVrfEntry 1.3.6.1.4.1.4874.2.2.29.1.18.1
The BGP VRF Entry describes BGP-specific characteristics of one VRF.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpVrfEntry  

juniBgpVrfName 1.3.6.1.4.1.4874.2.2.29.1.18.1.1
The name of the VPN Routing Forwarding (VRF) instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniVrfName  

juniBgpVrfSynchronization 1.3.6.1.4.1.4874.2.2.29.1.18.1.2
Set this object to true(1) in order to have IGP route synchronization enabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpVrfAutoSummary 1.3.6.1.4.1.4874.2.2.29.1.18.1.3
Set this object to true(1) in order to automatically summarize redistributed routes to their natural network mask.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpVrfExternalDistance 1.3.6.1.4.1.4874.2.2.29.1.18.1.4
Obsolete administrative distance for external routes. Replaced by juniBgpAddressFamilyExternalDistance.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32 1..255  

juniBgpVrfInternalDistance 1.3.6.1.4.1.4874.2.2.29.1.18.1.5
Obsolete administrative distance for internal routes. Replaced by juniBgpAddressFamilyInternalDistance.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32 1..255  

juniBgpVrfLocalDistance 1.3.6.1.4.1.4874.2.2.29.1.18.1.6
Obsolete administrative distance for local routes. Replaced by juniBgpAddressFamilyLocalDistance.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32 1..255  

juniBgpVrfResetConnectionType 1.3.6.1.4.1.4874.2.2.29.1.18.1.7
Writing a value to this object causes the sessions to all peers in this VRF to be cleared; the value determines what type of clear is executed (hard clear, soft clear in, soft clear out, etc.). Reading this object has no effect and always returns resetTypeNoop.
Status: current Access: read-create
OBJECT-TYPE    
  JuniBgpResetConnectionType  

juniBgpVrfRowStatus 1.3.6.1.4.1.4874.2.2.29.1.18.1.8
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniBgpVrfOperationalState 1.3.6.1.4.1.4874.2.2.29.1.18.1.9
The BGP VRF operational state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), up(1), down(2), overload(3)  

juniBgpVrfAddUnicastRoutesToMulticastView 1.3.6.1.4.1.4874.2.2.29.1.18.1.10
Set this object to true(1) in order to add routes learnt by IPv4 Unicast BGP to the multicast route table.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpVrfMaximumPathsEbgp 1.3.6.1.4.1.4874.2.2.29.1.18.1.11
The maximum number of routes received from EBGP peers which BGP can select as equal cost. Zero means that routes from EBGP peers cannot be selected as equal cost.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..16  

juniBgpVrfMaximumPathsIbgp 1.3.6.1.4.1.4874.2.2.29.1.18.1.12
The maximum number of routes received from IBGP peers which BGP can select as equal cost. Zero means that routes from IBGP peers cannot be selected as equal cost.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..16  

juniBgpVrfUnconfiguredAttributes 1.3.6.1.4.1.4874.2.2.29.1.18.1.13
On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
Status: current Access: read-create
OBJECT-TYPE    
  BITS juniBgpVrfSynchronization(0), juniBgpVrfAutoSummary(1), juniBgpVrfExternalDistance(2), juniBgpVrfInternalDistance(3), juniBgpVrfLocalDistance(4), juniBgpVrfAddUnicastRoutesToMulticastView(5), juniBgpVrfMaximumPathsEbgp(6), juniBgpVrfMaximumPathsIbgp(7), juniBgpVrfMaximumPathsEIbgp(8)  

juniBgpVrfMaximumPathsEIbgp 1.3.6.1.4.1.4874.2.2.29.1.18.1.14
The maximum number of routes received from both EBGP and IBGP peers which BGP can select as equal cost. Zero means that routes from both EBGP and IBGP peers cannot be selected as equal cost.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..16  

juniBgpVrfCarriersCarrierModeEnabled 1.3.6.1.4.1.4874.2.2.29.1.18.1.16
Obsolete the BGP carrier's carrier flag since there is no need for it when in carrier's carrier mode.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpAddressFamilyTable 1.3.6.1.4.1.4874.2.2.29.1.19
The BGP AddressFamily Entry describes BGP-specific characteristics of one AddressFamily.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpAddressFamilyEntry

juniBgpAddressFamilyEntry 1.3.6.1.4.1.4874.2.2.29.1.19.1
The BGP address family entry
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpAddressFamilyEntry  

juniBgpAddressFamilyVrfName 1.3.6.1.4.1.4874.2.2.29.1.19.1.1
The name of the VPN Routing Forwarding (VRF) instance in which this address-family is configured. The empty string indicates that this address-family is not in a VRF.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniVrfName  

juniBgpAddressFamilyAfi 1.3.6.1.4.1.4874.2.2.29.1.19.1.2
The AFI of the address-family.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpAfi  

juniBgpAddressFamilySafi 1.3.6.1.4.1.4874.2.2.29.1.19.1.3
The SAFI of the address-family.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpSafi  

juniBgpAddressFamilyDefaultOriginate 1.3.6.1.4.1.4874.2.2.29.1.19.1.4
Set this object to true(1) in order to advertise a default route, if present.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpAddressFamilyRouteFlapDampening 1.3.6.1.4.1.4874.2.2.29.1.19.1.5
Set this object to true(1) in order to enable route flap dampening.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpAddressFamilyDampeningSuppressThreshold 1.3.6.1.4.1.4874.2.2.29.1.19.1.6
The dampening cutoff threshold (scaled).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpAddressFamilyDampeningReuseThreshold 1.3.6.1.4.1.4874.2.2.29.1.19.1.7
The dampening reuse threshold (scaled).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpAddressFamilyDampeningMaxHoldDownTime 1.3.6.1.4.1.4874.2.2.29.1.19.1.8
Maximum route holddown time, in seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpAddressFamilyDampeningHalfLifeReachable 1.3.6.1.4.1.4874.2.2.29.1.19.1.9
Figure of merit half life for reachable routes, in seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpAddressFamilyDampeningHalfLifeUnreachable 1.3.6.1.4.1.4874.2.2.29.1.19.1.10
Figure of merit half life for unreachable routes, in seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniBgpAddressFamilyDampeningRouteMapName 1.3.6.1.4.1.4874.2.2.29.1.19.1.11
The name of the route-map used to determine which routes are dampened and which aren't and to set the dampening parameters for those routes which are dampenend. A zero length route-map name means don't use a route-map for this.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpAddressFamilyResetConnectionType 1.3.6.1.4.1.4874.2.2.29.1.19.1.12
Writing a value to this object causes one individual address family within the sessions to all peers in this VRF to be cleared; the value determines what type of clear is executed (hard clear, soft clear in, soft clear out, etc.). Note that hard clearing an address family within a session will bounce the session and thus also affect the other address families in the session. Reading this object has no effect and always returns resetTypeNoop.
Status: current Access: read-create
OBJECT-TYPE    
  JuniBgpResetConnectionType  

juniBgpAddressFamilyRowStatus 1.3.6.1.4.1.4874.2.2.29.1.19.1.13
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniBgpAddressFamilyOperationalState 1.3.6.1.4.1.4874.2.2.29.1.19.1.14
The BGP address family operational state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), up(1), down(2), overload(3)  

juniBgpAddressFamilyUnconfiguredAttributes 1.3.6.1.4.1.4874.2.2.29.1.19.1.15
On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
Status: current Access: read-create
OBJECT-TYPE    
  BITS juniBgpAddressFamilyDefaultOriginate(0), juniBgpAddressFamilyRouteFlapDampening(1), juniBgpAddressFamilyDampeningSuppressThreshold(2), juniBgpAddressFamilyDampeningReuseThreshold(3), juniBgpAddressFamilyDampeningMaxHoldDownTime(4), juniBgpAddressFamilyDampeningHalfLifeReachable(5), juniBgpAddressFamilyDampeningHalfLifeUnreachable(6), juniBgpAddressFamilyDampeningRouteMapName(7), juniBgpAddressFamilyExternalDistance(8), juniBgpAddressFamilyInternalDistance(9), juniBgpAddressFamilyLocalDistance(10), juniBgpAddressFamilyDefaultOriginateRouteMap(11), juniBgpAddressFamilyCheckVpnNextHops(12)  

juniBgpAddressFamilyExternalDistance 1.3.6.1.4.1.4874.2.2.29.1.19.1.16
The administrative distance for external routes.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..255  

juniBgpAddressFamilyInternalDistance 1.3.6.1.4.1.4874.2.2.29.1.19.1.17
The administrative distance for internal routes.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..255  

juniBgpAddressFamilyLocalDistance 1.3.6.1.4.1.4874.2.2.29.1.19.1.18
The administrative distance for local routes.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..255  

juniBgpAddressFamilyDefaultOriginateRouteMap 1.3.6.1.4.1.4874.2.2.29.1.19.1.19
The route-map to apply to the default route which is advertised as a result of setting juniBgpAddressFamilyDefaultOriginate to true. An empty string means that no route-map is applied.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniBgpAddressFamilyIpIntfProfileNameForMplsHeads 1.3.6.1.4.1.4874.2.2.29.1.19.1.20
Obsolete the name of the IP interface profile used by BGP to create IP dynamic interfaces on top of MPLS stacked tunnel heads. When support for BGP-created IP dynamic interfaces was removed, BGP profile names were obsoleted too.
Status: obsolete Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..80)  

juniBgpAddressFamilyIpIntfProfileNameForMplsTails 1.3.6.1.4.1.4874.2.2.29.1.19.1.21
Obsolete the name of the IP interface profile used by BGP to create IP dynamic interfaces on top of MPLS stacked tunnel tails. When support for BGP-created IP dynamic interfaces was removed, BGP profile names were obsoleted too.
Status: obsolete Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..80)  

juniBgpAddressFamilyIpIntfServiceProfileNameForMplsHeads 1.3.6.1.4.1.4874.2.2.29.1.19.1.22
Obsolete the name of the IP interface service-profile used by BGP to create IP dynamic interfaces on top of MPLS stacked tunnel heads. When support for BGP-created dynamic interfaces was removed, BGP profile names were obsoleted too.
Status: obsolete Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..80)  

juniBgpAddressFamilyIpIntfServiceProfileNameForMplsTails 1.3.6.1.4.1.4874.2.2.29.1.19.1.23
The name of the IP interface service-profile used by BGP to create IP dynamic interfaces on top of MPLS stacked tunnel tails. When support for BGP-created dynamic interfaces was removed, BGP profile names were obsoleted too.
Status: obsolete Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..80)  

juniBgpAddressFamilyCheckVpnNextHops 1.3.6.1.4.1.4874.2.2.29.1.19.1.24
If this object is set to true, the reachability of the next-hops of routes in this address-family are checked. If this object is set to false, the next-hops if routes in this address-families are always considered to be reachable. This attribute only applies to address- families with SAFI 128 (labeled-vpn-unicast). For all other address- families this attributes is meaningless and attempting to set the attribute will result in an error.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniBgpAddressFamilyPathSelectionIsDeferred 1.3.6.1.4.1.4874.2.2.29.1.19.1.25
Is path selection for the address-family currently deferred?
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpAddressFamilyPreventBgpRoutesFromBeingPushedToLineCards 1.3.6.1.4.1.4874.2.2.29.1.19.1.26
Is BGP still in the process of placing fresh routes in the route table after a restart? During this period the line cards are forced to continue forwarding using the old stale routes.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpAddressFamilyTimeUntilPathSelectionDeferTimerExpires 1.3.6.1.4.1.4874.2.2.29.1.19.1.27
The number of seconds until the path selection defer timer expires or zero if it is not running.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpStorageGroup 1.3.6.1.4.1.4874.2.2.29.1.20
OBJECT IDENTIFIER    

juniBgpStorageInitialHeapSize 1.3.6.1.4.1.4874.2.2.29.1.20.1
Obsolete initial size of the BGP heap in octets. The BGP heap is used for a small number of variable sized data structures.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxHeapSize 1.3.6.1.4.1.4874.2.2.29.1.20.2
Obsolete maximum size of the BGP heap in octets.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialVrfPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.4
Obsolete initial size of the VRF pool in entries. One entry is allocated from the VRF pool for each VRF used by BGP.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxVrfPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.5
Obsolete maximum size of the VRF pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialAddressFamilyPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.6
Obsolete initial size of the address-family pool in entries. One entry is allocated from the address-family pool for each address-family used by BGP.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxAddressFamilyPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.7
Obsolete initial size of the address-family pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialPeerPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.8
Obsolete initial size of the peer pool in entries. One entry is allocated from the peer pool for each peer configured in BGP.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxPeerPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.9
Obsolete maximum size of the peer pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialPeerAfPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.10
Obsolete initial size of the peer-address-family pool in entries. One entry is allocated from the peer-address-family pool for each address family activated for any peer in BGP (including the IPv4 unicast address families which are usually activated by default for each peer).
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxPeerAfPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.11
Obsolete maximum size of the peer-address-family pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialPeerGroupPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.12
Obsolete initial size of the peer-group pool in entries. One entry is allocated from the peer-group pool for each peer-group configured in BGP.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxPeerGroupPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.13
Obsolete maximum size of the peer-group pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialPeerGroupAfPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.14
Obsolete initial size of the peer-group-address-family pool in entries. One entry is allocated from the peer-group-address-family pool for each address family activated for any peer-group in BGP (including the IPv4 unicast address families which are usually activated by default for each peer-group).
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxPeerGroupAfPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.15
Obsolete maximum size of the peer-group-address-family pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialNetworkPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.16
Obsolete initial size of the network pool in entries. One entry is allocated from the network pool for each network configured in BGP.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxNetworkPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.17
Obsolete maximum size of the network pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialAggregatePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.18
Obsolete initial size of the aggregate pool in entries. One entry is allocated from the aggregate pool for each aggregate configured in BGP.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxAggregatePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.19
Obsolete maximum size of the aggregate pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialDestinationPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.20
Obsolete initial size of the destination pool in entries. One entry is allocated from the destination pool for each unique prefix in the BGP RIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxDestinationPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.21
Obsolete maximum size of the destination pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialRoutePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.22
Obsolete initial size of the route pool in entries. One entry is allocated from the route pool for each received non-VPN route in the BGP RIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxRoutePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.23
Obsolete maximum size of the route pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialAttributesPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.24
Obsolete initial size of the attributes pool in entries. One entry is allocated from the attributes pool for each unique combination of path attributes of routes in the BGP RIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxAttributesPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.25
Obsolete maximum size of the attributes pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialRouteFlapHistoryPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.26
Obsolete initial size of the route-flap-history pool in entries. One entry is allocated from the route-flap-history pool for each route in the BGP RIB which has route-flap dampening history associated with it.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxRouteFlapHistoryPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.27
Obsolete maximum size of the route-flap-history pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialNetworkRoutePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.28
Obsolete initial size of the network-route pool in entries. One entry is allocated from the network-route pool for each network route in the BGP RIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxNetworkRoutePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.29
Obsolete maximum size of the network-route pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialRedistributedRoutePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.30
Obsolete initial size of the redistributed-route pool in entries. One entry is allocated from the redistributed-route pool for each redistributed route in the BGP RIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxRedistributedRoutePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.31
Obsolete maximum size of the redistributed-route pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialAggregateRoutePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.32
Obsolete initial size of the aggregate-route pool in entries. One entry is allocated from the aggregate-route pool for each aggregate route in the BGP RIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxAggregateRoutePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.33
Obsolete maximum size of the aggregate-route pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialAutoSummaryRoutePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.34
Obsolete initial size of the auto-summary-route pool in entries. One entry is allocated from the auto-summary-route pool for each auto-summary route in the BGP RIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxAutoSummaryRoutePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.35
Obsolete maximum size of the auto-summary-route pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialHistoryRoutePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.36
Obsolete object is obsolete. Setting it has not effect and reading this object returns an undefined value.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxHistoryRoutePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.37
Obsolete object is obsolete. Setting it has not effect and reading this object returns an undefined value.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialSendQueueEntryPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.38
Obsolete initial size of the send-queue-entry pool in entries. One entry is allocated from the send-queue-entry pool for update messages which is queued for transmission to a peer.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxSendQueueEntryPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.39
Obsolete maximum size of the send-queue-entry pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialVpnRoutePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.40
Obsolete initial size of the vpn-route pool in entries. One entry is allocated from the vpn-route pool for each received VPN route in the BGP RIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxVpnRoutePoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.41
Obsolete maximum size of the vpn-route pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageInitialRouteTargetPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.42
Obsolete initial size of the route-target pool in entries. One entry is allocated from the route-target pool for each route-target imported in any VRF used by BGP.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpStorageMaxRouteTargetPoolSize 1.3.6.1.4.1.4874.2.2.29.1.20.43
Obsolete maximum size of the route-target pool in entries.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JuniBgpStorageInteger  

juniBgpNewRouteTable 1.3.6.1.4.1.4874.2.2.29.1.23
The BGP-4 Received Path Attribute Table contains additional information about paths to destination networks received from all BGP4 peers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpNewRouteEntry

juniBgpNewRouteEntry 1.3.6.1.4.1.4874.2.2.29.1.23.1
Additional information about a path to a network.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpNewRouteEntry  

juniBgpNewRouteVrfName 1.3.6.1.4.1.4874.2.2.29.1.23.1.1
The name of the VPN Routing Forwarding (VRF) instance in which this route is present. The empty string indicates that this route is not in a VRF.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniVrfName  

juniBgpNewRouteAfi 1.3.6.1.4.1.4874.2.2.29.1.23.1.2
The AFI of the address-family in which this route is present.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpAfi  

juniBgpNewRouteSafi 1.3.6.1.4.1.4874.2.2.29.1.23.1.3
The SAFI of the address-family in which this route is present.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpSafi  

juniBgpNewRouteIpAddrPrefix 1.3.6.1.4.1.4874.2.2.29.1.23.1.4
The IP address prefix of the route. This object is an IP address containing the prefix with length specified by juniBgpNewRouteIpAddrPrefixLen. Any bits beyond the length specified by juniBgpNewRouteIpAddrPrefixLen are zeroed.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniBgpNewRouteIpAddrPrefixLen 1.3.6.1.4.1.4874.2.2.29.1.23.1.5
Length in bits of the IP address prefix of the route.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..32  

juniBgpNewRouteDistinguisher 1.3.6.1.4.1.4874.2.2.29.1.23.1.6
The Route Distinguisher (RD) of the route. This object has an undefined value for non-VPN routes.
Status: current Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(8)  

juniBgpNewRoutePeer 1.3.6.1.4.1.4874.2.2.29.1.23.1.7
The IP address of the peer from which the route was received. This object has value 0.0.0.0 is the route was a locally originated route.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniBgpNewRouteRouteType 1.3.6.1.4.1.4874.2.2.29.1.23.1.8
The type of the route.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER routeTypeReceived(1), routeTypeNetwork(2), routeTypeRedistributed(3), routeTypeAggregate(4), routeTypeAutoSummary(5)  

juniBgpNewRouteOriginalRd 1.3.6.1.4.1.4874.2.2.29.1.23.1.9
The original Route Distinguisher (RD) of a VPN route. For VPN routes which are originated in a VRF or which are received from a CE the original RD is equal to the RD of the VRF. For VPN routes which are received from another PE and imported into a VRF, the original RD is the RD which was received from the other PE (the RD of the route itself is changed to the RD for the VRF when the route is imported into the VRF). For non-VPN routes the value of this object is undefined.
Status: current Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(8)  

juniBgpNewRouteOriginatorId 1.3.6.1.4.1.4874.2.2.29.1.23.1.10
The Originator-ID path attribute of the route if present. The juniBgpNewRouteOriginatorIdPresent object indicates whether the Originator-ID path attribute is present.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

juniBgpNewRouteAtomicAggregatePresent 1.3.6.1.4.1.4874.2.2.29.1.23.1.11
Atomic-Aggregate path attribute is present.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteMedPresent 1.3.6.1.4.1.4874.2.2.29.1.23.1.12
The Multi-Exit-Discriminator path attribute is present.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteLocalPrefPresent 1.3.6.1.4.1.4874.2.2.29.1.23.1.13
The Local-Pref path attribute is present.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteAggregatorPresent 1.3.6.1.4.1.4874.2.2.29.1.23.1.14
The Aggregator path attribute is present.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteCommunitiesPresent 1.3.6.1.4.1.4874.2.2.29.1.23.1.15
The Communities path attribute is present.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteOriginatorIdPresent 1.3.6.1.4.1.4874.2.2.29.1.23.1.16
The Originator-ID path attribute is present.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteClusterListPresent 1.3.6.1.4.1.4874.2.2.29.1.23.1.17
The Cluster-List path attribute is present.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteWeight 1.3.6.1.4.1.4874.2.2.29.1.23.1.18
The weight of the route.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteOrigin 1.3.6.1.4.1.4874.2.2.29.1.23.1.19
The value of the Origin path attribute.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER igp(1), egp(2), incomplete(3)  

juniBgpNewRouteASPathSegment 1.3.6.1.4.1.4874.2.2.29.1.23.1.20
The value of the AS-path path attribute (as encoded in the received update message).
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2..255)  

juniBgpNewRouteNextHop 1.3.6.1.4.1.4874.2.2.29.1.23.1.21
The value of the Next-Hop path attribute.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

juniBgpNewRouteMultiExitDisc 1.3.6.1.4.1.4874.2.2.29.1.23.1.22
The value of the Multi-Exit-Discriminator path attribute if present. The juniBgpNewRouteMedPresent object indicates whether the Multi-Exit-Discriminator path attribute is present.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteLocalPref 1.3.6.1.4.1.4874.2.2.29.1.23.1.23
The value of the Local-Pref path attribute if present. The juniBgpNewRouteLocalPrefPresent object indicates whether the Local-Pref path attribute is present.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteAtomicAggregate 1.3.6.1.4.1.4874.2.2.29.1.23.1.24
Whether or not the local system has selected a less specific route without selecting a more specific route.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER lessSpecificRouteNotSelected(1), lessSpecificRouteSelected(2)  

juniBgpNewRouteAggregatorAS 1.3.6.1.4.1.4874.2.2.29.1.23.1.25
The value of the AS field in the Aggregator path attribute if present. The juniBgpNewRouteAggregatorPresent object indicates whether the Aggregator path attribute is present.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpNewRouteAggregatorAddress 1.3.6.1.4.1.4874.2.2.29.1.23.1.26
The value of the address field in the Aggregator path attribute if present. The juniBgpNewRouteAggregatorPresent object indicates whether the Aggregator path attribute is present.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

juniBgpNewRouteBestInIpRouteTable 1.3.6.1.4.1.4874.2.2.29.1.23.1.27
When BGP places a routes in the IP route table, that route may not be used for forwarding traffic if there are other routes (e.g. IGP routes or static routes) to that same prefix with a better administrative distance in the IP route table. This object indicates whether or not the BGP route in the IP route table is the best route (and hence is used for forwarding traffic).
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteUnknown 1.3.6.1.4.1.4874.2.2.29.1.23.1.28
One or more path attributes not understood by this BGP4 speaker. Size zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size, if any, are not recorded by this object.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

juniBgpNewRouteExtendedCommunitiesPresent 1.3.6.1.4.1.4874.2.2.29.1.23.1.29
Is the Extended-Communities path attribute present?
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteValid 1.3.6.1.4.1.4874.2.2.29.1.23.1.30
Is the route valid? The route is declared invalid if there is something wrong with it which is not serious enough for sending a notification, but it serious enough for not placing it in the IP route table or propagating it to other peers (for example the next-hop of the route is a local address).
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteSuppressedBy 1.3.6.1.4.1.4874.2.2.29.1.23.1.31
Indicates whether or not the route is suppressed, and if so why: suppressedByNothing - Route is not suppressed. suppressedByAggregate - Route is suppressed by a summary-only aggregate. suppressedByAutoSummary - Route is suppressed by an auto-summary. suppressedByDampening - Route is suppressed as a result of route-flap dampening.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER suppressedByNothing(1), suppressedByAggregate(2), suppressedByAutoSummary(3), suppressedByDampening(4)  

juniBgpNewRouteNextHopReachable 1.3.6.1.4.1.4874.2.2.29.1.23.1.32
Is the indirect next-hop of the route reachable (i.e. can the indirect next-hop of the route be resolved to at least one direct next-hop)?
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteSynchronizedWithIgp 1.3.6.1.4.1.4874.2.2.29.1.23.1.33
Is the route is synchronized (i.e. is there is an IGP route to the same prefix in the IP route table)?
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRoutePlaceInIpRouteTable 1.3.6.1.4.1.4874.2.2.29.1.23.1.34
Has a BGP route for this prefix been placed in the IP route table?
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteAdvertiseToExternalPeers 1.3.6.1.4.1.4874.2.2.29.1.23.1.35
Should this route be advertised to external peers?
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteAdvertiseToInternalPeers 1.3.6.1.4.1.4874.2.2.29.1.23.1.36
Should this route be advertised to internal peers?
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteMplsLabel 1.3.6.1.4.1.4874.2.2.29.1.23.1.37
The obsolete MPLS label for the route. This object was obsoleted when in-label and out-label were introduced.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteNextHopMetric 1.3.6.1.4.1.4874.2.2.29.1.23.1.38
The metric of direct next-hop of this BGP route.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteMplsInLabel 1.3.6.1.4.1.4874.2.2.29.1.23.1.39
The MPLS in-label for the route. This is the label that MPLS frames are going to be received with.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteMplsOutLabel 1.3.6.1.4.1.4874.2.2.29.1.23.1.40
The MPLS out-label for the route. This is the label that MPLS frames are going to be sent with.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteLeaked 1.3.6.1.4.1.4874.2.2.29.1.23.1.41
Is the route leaked into this address-family from another address- family?
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteStale 1.3.6.1.4.1.4874.2.2.29.1.23.1.42
Is the route stale?
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpNewRouteFlapHistoryTable 1.3.6.1.4.1.4874.2.2.29.1.24
The BGP Route Flap History Table contains information about recorded route flap events.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpNewRouteFlapHistoryEntry

juniBgpNewRouteFlapHistoryEntry 1.3.6.1.4.1.4874.2.2.29.1.24.1
An instance in the list of route flap events.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpNewRouteFlapHistoryEntry  

juniBgpNewRouteFlapState 1.3.6.1.4.1.4874.2.2.29.1.24.1.1
Current state: stateAvailable(1) - indicates path is available stateSuppressedReachable(2) - indicates path is suppressed, destination is reachable stateSuppressedUnreachable(3) - indicates path in suppressed, destination is not reachable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER stateAvailable(1), stateSuppressedReachable(2), stateSuppressedUnreachable(3)  

juniBgpNewRouteFlapFigureOfMerit 1.3.6.1.4.1.4874.2.2.29.1.24.1.2
Calculated figure-of-merit.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteFlapRemainingTime 1.3.6.1.4.1.4874.2.2.29.1.24.1.3
Number of seconds until reuse or removal.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteFlapSuppressThreshold 1.3.6.1.4.1.4874.2.2.29.1.24.1.4
Damping cutoff threshold (scaled).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteFlapReuseThreshold 1.3.6.1.4.1.4874.2.2.29.1.24.1.5
Damping reuse threshold (scaled).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteFlapMaxHoldDownTime 1.3.6.1.4.1.4874.2.2.29.1.24.1.6
Maximum route holddown time (seconds).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteFlapHalfLifeReachable 1.3.6.1.4.1.4874.2.2.29.1.24.1.7
Figure of merit half life for reachable routes (seconds).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteFlapHalfLifeUnreachable 1.3.6.1.4.1.4874.2.2.29.1.24.1.8
Figure of merit half life for unreachable routes (seconds).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteCommunityTable 1.3.6.1.4.1.4874.2.2.29.1.25
The BGP-4 Path Community Table contains information about communities within destination networks received from all BGP4 peers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpNewRouteCommunityEntry

juniBgpNewRouteCommunityEntry 1.3.6.1.4.1.4874.2.2.29.1.25.1
Community attribute information within a path to a network.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpNewRouteCommunityEntry  

juniBgpNewRouteCommunityNumber 1.3.6.1.4.1.4874.2.2.29.1.25.1.1
The community number.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpNewRouteExtendedCommunityTable 1.3.6.1.4.1.4874.2.2.29.1.26
The BGP-4 Path Extended Community Table contains information about communities within destination networks received from all BGP4 peers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpNewRouteExtendedCommunityEntry

juniBgpNewRouteExtendedCommunityEntry 1.3.6.1.4.1.4874.2.2.29.1.26.1
Extended Community attribute information within a path to a network.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpNewRouteExtendedCommunityEntry  

juniBgpNewRouteExtendedCommunityNumber 1.3.6.1.4.1.4874.2.2.29.1.26.1.1
The extended community number.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

juniBgpNewRouteClusterIdTable 1.3.6.1.4.1.4874.2.2.29.1.27
The BGP-4 Path ClusterId Table contains information about router reflector cluster IDs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpNewRouteClusterIdEntry

juniBgpNewRouteClusterIdEntry 1.3.6.1.4.1.4874.2.2.29.1.27.1
ClusterId attribute information within a path to a network.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniBgpNewRouteClusterIdEntry  

juniBgpNewRouteClusterId 1.3.6.1.4.1.4874.2.2.29.1.27.1.1
The cluster ID.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpRouteTable 1.3.6.1.4.1.4874.2.2.29.1.13
The obsolete BGP-4 Received Path Attribute Table contained additional information about paths to destination networks received from all BGP4 peers. This table has been replaced by the juniBgpNewRouteTable.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpRouteEntry

juniBgpRouteEntry 1.3.6.1.4.1.4874.2.2.29.1.13.1
Additional information about a path to a network.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  JuniBgpRouteEntry  

juniBgpRouteOriginatorId 1.3.6.1.4.1.4874.2.2.29.1.13.1.1
The Originator-ID path attribute of the route if present. The juniBgpRouteOriginatorIdPresent object indicates whether the Originator-ID path attribute is present.
Status: obsolete Access: read-only
OBJECT-TYPE    
  IpAddress  

juniBgpRouteAtomicAggregatePresent 1.3.6.1.4.1.4874.2.2.29.1.13.1.2
Atomic-Aggregate path attribute is present.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteMedPresent 1.3.6.1.4.1.4874.2.2.29.1.13.1.3
The Multi-Exit-Discriminator path attribute is present.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteLocalPrefPresent 1.3.6.1.4.1.4874.2.2.29.1.13.1.4
The Local-Pref path attribute is present.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteAggregatorPresent 1.3.6.1.4.1.4874.2.2.29.1.13.1.5
The Aggregator path attribute is present.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteCommunitiesPresent 1.3.6.1.4.1.4874.2.2.29.1.13.1.6
The Communities path attribute is present.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteOriginatorIdPresent 1.3.6.1.4.1.4874.2.2.29.1.13.1.7
The Originator-ID path attribute is present.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteClusterListPresent 1.3.6.1.4.1.4874.2.2.29.1.13.1.8
The Cluster-List path attribute is present.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteWeight 1.3.6.1.4.1.4874.2.2.29.1.13.1.9
The weight of the route.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpRouteVrfName 1.3.6.1.4.1.4874.2.2.29.1.13.1.10
The name of the VPN Routing Forwarding (VRF) instance in which this route is present. The empty string indicates that this route is not in a VRF.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  JuniVrfName  

juniBgpRouteAfi 1.3.6.1.4.1.4874.2.2.29.1.13.1.11
The AFI of the address-family in which this route is present.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  JuniBgpAfi  

juniBgpRouteSafi 1.3.6.1.4.1.4874.2.2.29.1.13.1.12
The SAFI of the address-family in which this route is present.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  JuniBgpSafi  

juniBgpRoutePeer 1.3.6.1.4.1.4874.2.2.29.1.13.1.13
The IP address of the peer from which the route was received. This object has value 0.0.0.0 is the route was a locally originated route.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniBgpRouteIpAddrPrefixLen 1.3.6.1.4.1.4874.2.2.29.1.13.1.14
Length in bits of the IP address prefix of the route.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 0..32  

juniBgpRouteIpAddrPrefix 1.3.6.1.4.1.4874.2.2.29.1.13.1.15
The IP address prefix of the route. This object is an IP address containing the prefix with length specified by juniBgpNewRouteIpAddrPrefixLen. Any bits beyond the length specified by juniBgpNewRouteIpAddrPrefixLen are zeroed.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniBgpRouteRouteType 1.3.6.1.4.1.4874.2.2.29.1.13.1.16
The type of the route.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER routeTypeReceived(1), routeTypeNetwork(2), routeTypeRedistributed(3), routeTypeAggregate(4), routeTypeAutoSummary(5)  

juniBgpRouteOrigin 1.3.6.1.4.1.4874.2.2.29.1.13.1.17
The value of the Origin path attribute.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER igp(1), egp(2), incomplete(3)  

juniBgpRouteASPathSegment 1.3.6.1.4.1.4874.2.2.29.1.13.1.18
The value of the AS-path path attribute (as encoded in the received update message).
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2..255)  

juniBgpRouteNextHop 1.3.6.1.4.1.4874.2.2.29.1.13.1.19
The value of the Next-Hop path attribute.
Status: obsolete Access: read-only
OBJECT-TYPE    
  IpAddress  

juniBgpRouteMultiExitDisc 1.3.6.1.4.1.4874.2.2.29.1.13.1.20
The value of the Multi-Exit-Discriminator path attribute if present. The juniBgpRouteMedPresent object indicates whether the Multi-Exit-Discriminator path attribute is present.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpRouteLocalPref 1.3.6.1.4.1.4874.2.2.29.1.13.1.21
The value of the Local-Pref path attribute if present. The juniBgpRouteLocalPrefPresent object indicates whether the Local-Pref path attribute is present.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpRouteAtomicAggregate 1.3.6.1.4.1.4874.2.2.29.1.13.1.22
Whether or not the local system has selected a less specific route without selecting a more specific route.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER lessSpecificRouteNotSelected(1), lessSpecificRouteSelected(2)  

juniBgpRouteAggregatorAS 1.3.6.1.4.1.4874.2.2.29.1.13.1.23
The value of the AS field in the Aggregator path attribute if present. The juniBgpRouteAggregatorPresent object indicates whether the Aggregator path attribute is present.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

juniBgpRouteAggregatorAddress 1.3.6.1.4.1.4874.2.2.29.1.13.1.24
The value of the address field in the Aggregator path attribute if present. The juniBgpRouteAggregatorPresent object indicates whether the Aggregator path attribute is present.
Status: obsolete Access: read-only
OBJECT-TYPE    
  IpAddress  

juniBgpRouteBestInIpRouteTable 1.3.6.1.4.1.4874.2.2.29.1.13.1.25
When BGP places a routes in the IP route table, that route may not be used for forwarding traffic if there are other routes (e.g. IGP routes or static routes) to that same prefix with a better administrative distance in the IP route table. This object indicates whether or not the BGP route in the IP route table is the best route (and hence is used for forwarding traffic).
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteUnknown 1.3.6.1.4.1.4874.2.2.29.1.13.1.26
One or more path attributes not understood by this BGP4 speaker. Size zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size, if any, are not recorded by this object.
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

juniBgpRouteExtendedCommunitiesPresent 1.3.6.1.4.1.4874.2.2.29.1.13.1.27
Is the Extended-Communities path attribute present?
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteValid 1.3.6.1.4.1.4874.2.2.29.1.13.1.28
Is the route valid? The route is declared invalid if there is something wrong with it which is not serious enough for sending a notification, but it serious enough for not placing it in the IP route table or propagating it to other peers (for example the next-hop of the route is a local address).
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteSuppressedBy 1.3.6.1.4.1.4874.2.2.29.1.13.1.29
Indicates whether or not the route is suppressed, and if so why: suppressedByNothing - Route is not suppressed. suppressedByAggregate - Route is suppressed by a summary-only aggregate. suppressedByAutoSummary - Route is suppressed by an auto-summary. suppressedByDampening - Route is suppressed as a result of route-flap dampening.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER suppressedByNothing(1), suppressedByAggregate(2), suppressedByAutoSummary(3), suppressedByDampening(4)  

juniBgpRouteNextHopReachable 1.3.6.1.4.1.4874.2.2.29.1.13.1.30
Is the indirect next-hop of the route reachable (i.e. can the indirect next-hop of the route be resolved to at least one direct next-hop)?
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteSynchronizedWithIgp 1.3.6.1.4.1.4874.2.2.29.1.13.1.31
Is the route is synchronized (i.e. is there is an IGP route to the same prefix in the IP route table)?
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRoutePlaceInIpRouteTable 1.3.6.1.4.1.4874.2.2.29.1.13.1.32
Has a BGP route for this prefix been placed in the IP route table?
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteAdvertiseToExternalPeers 1.3.6.1.4.1.4874.2.2.29.1.13.1.33
Should this route be advertised to external peers?
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteAdvertiseToInternalPeers 1.3.6.1.4.1.4874.2.2.29.1.13.1.34
Should this route be advertised to internal peers?
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

juniBgpRouteDistinguisher 1.3.6.1.4.1.4874.2.2.29.1.13.1.35
The Route Distinguisher (RD) of the route. This object has an undefined value for non-VPN routes.
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

juniBgpRouteMplsLabel 1.3.6.1.4.1.4874.2.2.29.1.13.1.36
The MPLS label for the route.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpRouteNextHopMetric 1.3.6.1.4.1.4874.2.2.29.1.13.1.37
The metric of direct next-hop of this BGP route.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpRouteFlapHistoryTable 1.3.6.1.4.1.4874.2.2.29.1.12
The obsolete BGP Route Flap History Table contained information about recorded route flap events. This table has been replaced by the juniBgpNewRouteFlapHistoryTable.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpRouteFlapHistoryEntry

juniBgpRouteFlapHistoryEntry 1.3.6.1.4.1.4874.2.2.29.1.12.1
An instance in the list of route flap events.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  JuniBgpRouteFlapHistoryEntry  

juniBgpRouteFlapState 1.3.6.1.4.1.4874.2.2.29.1.12.1.1
Current state: stateAvailable(1) - indicates path is available stateSuppressedReachable(2) - indicates path is suppressed, destination is reachable stateSuppressedUnreachable(3) - indicates path in suppressed, destination is not reachable
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER stateAvailable(1), stateSuppressedReachable(2), stateSuppressedUnreachable(3)  

juniBgpRouteFlapFigureOfMerit 1.3.6.1.4.1.4874.2.2.29.1.12.1.2
Calculated figure-of-merit.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpRouteFlapRemainingTime 1.3.6.1.4.1.4874.2.2.29.1.12.1.3
Number of seconds until reuse or removal.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpRouteFlapSuppressThreshold 1.3.6.1.4.1.4874.2.2.29.1.12.1.4
Damping cutoff threshold (scaled).
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpRouteFlapReuseThreshold 1.3.6.1.4.1.4874.2.2.29.1.12.1.5
Damping reuse threshold (scaled).
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpRouteFlapMaxHoldDownTime 1.3.6.1.4.1.4874.2.2.29.1.12.1.6
Maximum route holddown time (seconds).
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpRouteFlapHalfLifeReachable 1.3.6.1.4.1.4874.2.2.29.1.12.1.7
Figure of merit half life for reachable routes (seconds).
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpRouteFlapHalfLifeUnreachable 1.3.6.1.4.1.4874.2.2.29.1.12.1.8
Figure of merit half life for unreachable routes (seconds).
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpRouteCommunityTable 1.3.6.1.4.1.4874.2.2.29.1.14
The obsolete BGP-4 Path Community Table contained information about communities within destination networks received from all BGP4 peers. This table has been replaced by the juniBgpNewRouteCommunityTable.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpRouteCommunityEntry

juniBgpRouteCommunityEntry 1.3.6.1.4.1.4874.2.2.29.1.14.1
Community attribute information within a path to a network.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  JuniBgpRouteCommunityEntry  

juniBgpRouteCommunityNumber 1.3.6.1.4.1.4874.2.2.29.1.14.1.1
The community number.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpRouteExtendedCommunityTable 1.3.6.1.4.1.4874.2.2.29.1.22
The obsolete BGP-4 Path Extended Community Table contained information about communities within destination networks received from all BGP4 peers. This table has been replaced by the juniBgpNewRouteExtendedCommunityTable.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpRouteExtendedCommunityEntry

juniBgpRouteExtendedCommunityEntry 1.3.6.1.4.1.4874.2.2.29.1.22.1
Extended Community attribute information within a path to a network.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  JuniBgpRouteExtendedCommunityEntry  

juniBgpRouteExtendedCommunityNumber 1.3.6.1.4.1.4874.2.2.29.1.22.1.1
The extended community number.
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

juniBgpRouteClusterIdTable 1.3.6.1.4.1.4874.2.2.29.1.15
The obsolete BGP-4 Path ClusterId Table contained information about router reflector cluster IDs. This table has been replaced by the juniBgpNewRouteClusterIdTable.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniBgpRouteClusterIdEntry

juniBgpRouteClusterIdEntry 1.3.6.1.4.1.4874.2.2.29.1.15.1
ClusterId attribute information within a path to a network.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  JuniBgpRouteClusterIdEntry  

juniBgpRouteClusterId 1.3.6.1.4.1.4874.2.2.29.1.15.1.1
The cluster id.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniBgpConformance 1.3.6.1.4.1.4874.2.2.29.2
OBJECT IDENTIFIER    

juniBgpCompliances 1.3.6.1.4.1.4874.2.2.29.2.1
OBJECT IDENTIFIER    

juniBgpConfGroups 1.3.6.1.4.1.4874.2.2.29.2.2
OBJECT IDENTIFIER    

juniBgpCompliance 1.3.6.1.4.1.4874.2.2.29.2.1.1
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when the juniBgpDefaultIPv4Unicast object was added to the general cofiguation group.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance2 1.3.6.1.4.1.4874.2.2.29.2.1.2
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when the original route destination was added as an index to each of the route configuration tables.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance3 1.3.6.1.4.1.4874.2.2.29.2.1.3
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when the peer and peer-group local-as support was added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance4 1.3.6.1.4.1.4874.2.2.29.2.1.4
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support was added for adding unicast BGP routes into a multicast view.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance5 1.3.6.1.4.1.4874.2.2.29.2.1.5
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when the juniBgpRedistributeInternal object was added to the general configuration group and the history pool size objects were obsoleted and the ability to unconfigure BGP attributes from the MIB was added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance6 1.3.6.1.4.1.4874.2.2.29.2.1.6
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for four-octet AS-numbers, dynamic capability negotiation, iBGP multipath, confederation peers filter-list, and address family maximum prefix strict was added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance7 1.3.6.1.4.1.4874.2.2.29.2.1.7
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for advertise-best-external-to-internal was added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance8 1.3.6.1.4.1.4874.2.2.29.2.1.8
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for maximum-paths eiBGP and other features were added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance9 1.3.6.1.4.1.4874.2.2.29.2.1.9
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for send-label was added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance10 1.3.6.1.4.1.4874.2.2.29.2.1.10
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for a route-map for default-information originate and neighbor ... default-originate was added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance11 1.3.6.1.4.1.4874.2.2.29.2.1.11
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when MIB support for graceful restart was added
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance12 1.3.6.1.4.1.4874.2.2.29.2.1.12
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when BGP storage support was removed and when MIB support for next-hop-unchanged was added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance13 1.3.6.1.4.1.4874.2.2.29.2.1.13
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for BGP BFD was added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance14 1.3.6.1.4.1.4874.2.2.29.2.1.14
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for ibgp-singlehop was added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance15 1.3.6.1.4.1.4874.2.2.29.2.1.15
Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for conditional advertisement was added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniBgpCompliance16 1.3.6.1.4.1.4874.2.2.29.2.1.16
The compliance statement for entities which implement the Juniper BGP MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

juniBgpGeneralConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.1
Obsolete collection of objects providing general management of BGP in a Juniper product. This group became obsolete when the juniBgpDefaultIPv4Unicast object was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpStatisticsConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.2
A collection of objects providing statistics of BGP operations in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpConfederationPeerConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.3
Deprecated object providing management of BGP-specific confederation peers in a Juniper product. This group became deprecated when support for four-octet AS-numbers was added.
Status: deprecated Access: read-only
OBJECT-GROUP    

juniBgpPeerConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.4
Obsolete collection of objects providing management of BGP peers in a Juniper product. This group became obsolete when the juniBgpPeerLocalAsNumber object was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpAfiSafiPeerConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.5
A collection of objects providing management of BGP-specific AFI and SAFI peers in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpPeerAddressFamilyConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.6
Obsolete collection of objects providing management of BGP peer address families in a Juniper product. This group became obsolete when the ability to unconfigure attributes using the MIB was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.7
Obsolete collection of objects providing management of BGP peer groups in a Juniper product. This group became obsolete when the juniBgpPeerGroupLocalAsNumber object was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupAddressFamilyConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.8
Obsolete collection of objects providing management of BGP peer group address families in a Juniper product. This group was obsoleted when the ability to unconfigure BGP attributes using the MIB was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpRouteConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.9
Obsolete collection of objects providing management of BGP routes in a Juniper product. This group became obsolete when the original route destination was added as an index to each of the tables.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpNetworkConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.10
Obsolete collection of objects providing management of BGP networks in a Juniper product. This group was obsoleted when the ability to unconfigure BGP attributes using the MIB was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpAggregateConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.11
Obsolete collection of objects providing consolidation of BGP route information in a Juniper product. This group was obsoleted when the ability to unconfigure BGP attributes using the MIB was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpVrfConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.12
Obsolete collection of objects providing management of BGP-specific VPN routing forwarding (VRF) characteristics in a Juniper product. This group became obsolete when the juniBgpVrfAddUnicastRoutesToMulticastView object was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpAddressFamilyConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.13
Obsolete collection of objects providing management of BGP address families in a Juniper product. This group was obsoleted when the ability to unconfigure BGP attributes using the MIB was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpStorageConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.14
Obsolete collection of objects providing management of BGP characteristics in a Juniper product that will not take affect until reboot. This group became obsolete when the history pool size objects were obsoleted.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpGeneralConfGroup2 1.3.6.1.4.1.4874.2.2.29.2.2.15
Obsolete collection of objects providing general management in a Juniper product. This group became obsolete when the juniBgpRedistributeInternal object and unconfigure support were added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpNewRouteConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.16
Obsolete collection of objects providing management of BGP routes in a Juniper product. This group was obsoleted when label was replaced by in-label and out-label.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerConfGroup2 1.3.6.1.4.1.4874.2.2.29.2.2.17
Obsolete collection of objects providing management of BGP peers in a Juniper product. This group became obsolete when the ability to unconfigure BGP attributes from the MIB was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupConfGroup2 1.3.6.1.4.1.4874.2.2.29.2.2.18
Obsolete collection of objects providing management of BGP peer groups in a Juniper product. This group was obsoleted when the ability to unconfigure BGP attributes using the MIB was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpVrfConfGroup2 1.3.6.1.4.1.4874.2.2.29.2.2.19
Obsolete collection of objects providing management of BGP-specific VPN routing forwarding (VRF) characteristics in a Juniper product. This group was obsoleted when the ability to unconfigure BGP attributes using the MIB was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpGeneralConfGroup3 1.3.6.1.4.1.4874.2.2.29.2.2.20
Obsolete collection of objects providing general management of BGP in a Juniper product. This group became obsolete when four-octet AS-numbers and maximum-paths iBGP support was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpStorageConfGroup2 1.3.6.1.4.1.4874.2.2.29.2.2.21
Obsolete collection of objects providing management of BGP characteristics in a Juniper product that will not take affect until reboot. This group became obsolete when storage heap size objects were obsoleted.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerConfGroup3 1.3.6.1.4.1.4874.2.2.29.2.2.22
Obsolete collection of objects providing management of BGP peers in a Juniper product. This groups was obsoleted when support for four octet AS numbers was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerAddressFamilyConfGroup2 1.3.6.1.4.1.4874.2.2.29.2.2.23
Obsolete collection of objects providing management of BGP peer address families in a Juniper product. This group was obsoleted when support for ORFs was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupConfGroup3 1.3.6.1.4.1.4874.2.2.29.2.2.24
Obsolete collection of objects providing management of BGP peer groups in a Juniper product. This group was obsoleted when support for dynamic capability negotiation was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupAddressFamilyConfGroup2 1.3.6.1.4.1.4874.2.2.29.2.2.25
Obsolete collection of objects providing management of BGP peer group address families in a Juniper product. This group was obsoleted when support for ORFs was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpNetworkConfGroup2 1.3.6.1.4.1.4874.2.2.29.2.2.26
A collection of objects providing management of BGP networks in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpAggregateConfGroup2 1.3.6.1.4.1.4874.2.2.29.2.2.27
A collection of objects providing consolidation of BGP route information in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpVrfConfGroup3 1.3.6.1.4.1.4874.2.2.29.2.2.28
Obsolete collection of objects providing management of BGP-specific VPN routing forwarding (VRF) characteristics in a Juniper product. This group was obsoleted when support for iBGP multipath was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpAddressFamilyConfGroup2 1.3.6.1.4.1.4874.2.2.29.2.2.29
Obsolete collection of objects providing management of BGP address-family groups in a Juniper product. This group was obsoleted when support for administrative distance was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpGeneralConfGroup4 1.3.6.1.4.1.4874.2.2.29.2.2.30
Obsolete collection of objects providing general management of BGP in a Juniper product. This group became obsolete when support for advertise-best-external-to-internal was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpFourOctetConfederationPeerConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.31
An object providing management of BGP-specific confederation peers in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpPeerConfGroup4 1.3.6.1.4.1.4874.2.2.29.2.2.32
Obsolete collection of objects providing management of BGP peers in a Juniper product. This group was obsoleted when support for site-of-origin was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerAddressFamilyConfGroup3 1.3.6.1.4.1.4874.2.2.29.2.2.33
Obsolete collection of objects providing management of BGP peer address families in a Juniper product. This group was obsoleted when support for send-label was added
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupConfGroup4 1.3.6.1.4.1.4874.2.2.29.2.2.34
Obsolete collection of objects providing management of BGP peer groups in a Juniper product. This group was obsoleted when support for site-of-origin was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupAddressFamilyConfGroup3 1.3.6.1.4.1.4874.2.2.29.2.2.35
Obsolete collection of objects providing management of BGP peer group address families in a Juniper product. This group was obsoleted when support for send-label was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpVrfConfGroup4 1.3.6.1.4.1.4874.2.2.29.2.2.36
Obsolete collection of objects providing management of BGP-specific VPN routing forwarding (VRF) characteristics in a Juniper product. This group was obsoleted when support for eiBGP multipath was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpDeprecatedGroup 1.3.6.1.4.1.4874.2.2.29.2.2.37
A collection of deprecated objects that continue to be supported on some current Juniper products.
Status: deprecated Access: read-only
OBJECT-GROUP    

juniBgpNewRouteConfGroup2 1.3.6.1.4.1.4874.2.2.29.2.2.38
Obsolete collection of objects providing management of BGP routes in a Juniper product. This group was obsoleted when support for leaked flag attribute of the BGP route was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpGeneralConfGroup5 1.3.6.1.4.1.4874.2.2.29.2.2.39
Obsolete collection of objects providing general management of BGP in a Juniper product. This group was obsoleted when MIB support for graceful restart was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerConfGroup5 1.3.6.1.4.1.4874.2.2.29.2.2.40
Obsolete collection of objects providing management of BGP peers in a Juniper product. This group was obsoleted when support for the new dynamic capability negotiation draft was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupConfGroup5 1.3.6.1.4.1.4874.2.2.29.2.2.41
Obsolete collection of objects providing management of BGP peer groups in a Juniper product. This group was obsoleted when support for the new dynamic capability negotiation draft was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpVrfConfGroup5 1.3.6.1.4.1.4874.2.2.29.2.2.42
Obsolete collection of objects providing management of BGP-specific VPN routing forwarding (VRF) characteristics in a Juniper product. This group was obsoleted when support for carrier's carrier was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpAddressFamilyConfGroup3 1.3.6.1.4.1.4874.2.2.29.2.2.43
Obsolete collection of objects providing management of BGP address families in a Juniper product. This group was obsoleted when support for check-vpn-next-hops was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpStorageConfGroup3 1.3.6.1.4.1.4874.2.2.29.2.2.44
Obsolete collection of objects providing management of BGP characteristics in a Juniper product that will not take affect until reboot. This group became obsolete when storage support objects were obsoleted.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpNewRouteConfGroup3 1.3.6.1.4.1.4874.2.2.29.2.2.45
Obsolete collection of objects providing management of BGP routes in a Juniper product. This group was obsoleted when MIB support for graceful restart was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerAddressFamilyConfGroup4 1.3.6.1.4.1.4874.2.2.29.2.2.46
Obsolete collection of objects providing management of BGP peer address families in a Juniper product. This group was obsoleted when support for a route-map for neighbor ... default-originate was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupAddressFamilyConfGroup4 1.3.6.1.4.1.4874.2.2.29.2.2.47
Obsolete collection of objects providing management of BGP peer group address families in a Juniper product. This group was obsoleted when support for a route-map for neighbor ... default-originate was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpVrfConfGroup6 1.3.6.1.4.1.4874.2.2.29.2.2.48
Obsolete collection of objects providing management of BGP-specific VPN routing forwarding (VRF) characteristics in a Juniper product. This group was obsoleted when the BGP-specific carrier's carrier flag was removed.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpAddressFamilyConfGroup4 1.3.6.1.4.1.4874.2.2.29.2.2.49
Obsolete collection of objects providing management of BGP address families in a Juniper product. This group was obsoleted when support for the route-map option in default-information originate was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerAddressFamilyConfGroup5 1.3.6.1.4.1.4874.2.2.29.2.2.50
Obsolete collection of objects providing management of BGP peer address families in a Juniper product. This group was obsoleted when MIB support for graceful restart was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerAddressFamilyConfGroup6 1.3.6.1.4.1.4874.2.2.29.2.2.58
Obsolete collection of objects providing management of BGP peer address families in a Juniper product. This group was obsoleted when MIB support for next-hop-unchanged was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupAddressFamilyConfGroup5 1.3.6.1.4.1.4874.2.2.29.2.2.51
Obsolete collection of objects providing management of BGP peer group address families in a Juniper product. This group was obsoleted when MIB support for next-hop-unchanged was added.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpAddressFamilyConfGroup5 1.3.6.1.4.1.4874.2.2.29.2.2.52
Obsolete collection of objects providing management of BGP address families in a Juniper product. This group was obsoleted when MIB support for graceful restart was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerConfGroup6 1.3.6.1.4.1.4874.2.2.29.2.2.53
Obsolete collection of objects providing management of BGP peers in a Juniper product. This group was obsoleted when MIB support for graceful restart was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupConfGroup6 1.3.6.1.4.1.4874.2.2.29.2.2.54
Obsolete collection of objects providing management of BGP peer groups in a Juniper product. This group was obsoleted when MIB support for graceful restart was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerDynamicCapabilityConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.55
A collection of objects providing management of BGP dynamic capability negotiation.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpGeneralConfGroup6 1.3.6.1.4.1.4874.2.2.29.2.2.56
A collection of objects providing general management of BGP in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpPeerConfGroup7 1.3.6.1.4.1.4874.2.2.29.2.2.57
Obsolete collection of objects providing management of BGP peers in a Juniper product. This group was obsoleted when support for BFD was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupConfGroup7 1.3.6.1.4.1.4874.2.2.29.2.2.59
Obsolete collection of objects providing management of BGP peer groups in a Juniper product. This group was obsoleted when support for BFD was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpNewRouteConfGroup4 1.3.6.1.4.1.4874.2.2.29.2.2.60
A collection of objects providing management of BGP routes in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpAddressFamilyConfGroup6 1.3.6.1.4.1.4874.2.2.29.2.2.61
Obsolete collection of objects providing management of BGP address families in a Juniper product. This group was obsoleted when BGP-created IP dynamic interface profile support has been removed.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpVrfConfGroup7 1.3.6.1.4.1.4874.2.2.29.2.2.62
A collection of objects providing management of BGP-specific VPN routing forwarding (VRF) characteristics in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpPeerAddressFamilyConfGroup7 1.3.6.1.4.1.4874.2.2.29.2.2.63
A collection of objects providing management of BGP peer address families in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupAddressFamilyConfGroup6 1.3.6.1.4.1.4874.2.2.29.2.2.64
A collection of objects providing management of BGP peer group address families in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpAddressFamilyConfGroup7 1.3.6.1.4.1.4874.2.2.29.2.2.65
A collection of objects providing management of BGP address families in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpPeerConfGroup8 1.3.6.1.4.1.4874.2.2.29.2.2.66
Obsolete collection of objects providing management of BGP peers in a Juniper product. This group was obsoleted when support for ibgp-singlehop was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupConfGroup8 1.3.6.1.4.1.4874.2.2.29.2.2.67
Obsolete collection of objects providing management of BGP peers in a Juniper product. This group was obsoleted when support for ibgp-singlehop was added.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpPeerConfGroup9 1.3.6.1.4.1.4874.2.2.29.2.2.68
A collection of objects providing management of BGP peers in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupConfGroup9 1.3.6.1.4.1.4874.2.2.29.2.2.69
A collection of objects providing management of BGP peer groups in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpPeerAddressFamilyConditionalAdvConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.70
A collection of objects providing management of BGP Conditional Advertisement for peers in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniBgpPeerGroupAddressFamilyConditionalAdvConfGroup 1.3.6.1.4.1.4874.2.2.29.2.2.71
A collection of objects providing management of BGP Conditional Advertisement for peer groups in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor