LIEBERT-GP-SYSTEM-MIB
File:
LIEBERT-GP-SYSTEM-MIB.mib (18872 bytes)
Imported modules
Imported symbols
Defined Types
| LgpSysDeviceComponentEntry |
|
| SEQUENCE |
|
|
|
| |
lgpSysDeviceComponentIndex |
Unsigned32 |
|
| |
lgpSysDeviceComponentDescr |
OBJECT IDENTIFIER |
|
| |
lgpSysDeviceComponentSerialNum |
DisplayString |
Size(255) |
| |
lgpSysDeviceComponentModelNum |
DisplayString |
Size(255) |
Defined Values
| liebertSystemModule |
1.3.6.1.4.1.476.1.42.1.8.1 |
| The MIB module used to specify Liebert Controller OIDs
Copyright 2000-2008 Liebert Corporation. All rights reserved.
Reproduction of this document is authorized on the condition
that the forgoing copyright notice is included.
This Specification is supplied 'AS IS' and Liebert Corporation
makes no warranty, either express or implied, as to the use,
operation, condition, or performance of the Specification. |
| MODULE-IDENTITY |
|
|
|
| lgpSysStatistics |
1.3.6.1.4.1.476.1.42.3.7.1 |
| This sub-tree is used to register Liebert System Statistics object
identifiers. |
| Status: current |
Access: read-only |
| OBJECT-IDENTITY |
|
|
|
| lgpSysStatus |
1.3.6.1.4.1.476.1.42.3.7.2 |
| This sub-tree is used to register Liebert System Status object
identifiers. |
| Status: current |
Access: read-only |
| OBJECT-IDENTITY |
|
|
|
| lgpSysSettings |
1.3.6.1.4.1.476.1.42.3.7.3 |
| This sub-tree is used to register Liebert System Settings object
identifiers. |
| Status: current |
Access: read-only |
| OBJECT-IDENTITY |
|
|
|
| lgpSysControl |
1.3.6.1.4.1.476.1.42.3.7.4 |
| This sub-tree is used to register Liebert System Control object
identifiers. |
| Status: current |
Access: read-only |
| OBJECT-IDENTITY |
|
|
|
| lgpSysTime |
1.3.6.1.4.1.476.1.42.3.7.5 |
| This sub-tree is used to register Liebert System Time object
identifiers. |
| Status: current |
Access: read-only |
| OBJECT-IDENTITY |
|
|
|
| lgpSysMaintenance |
1.3.6.1.4.1.476.1.42.3.7.6 |
| This sub-tree is used to register Liebert System Maintenance object
identifiers. |
| Status: current |
Access: read-only |
| OBJECT-IDENTITY |
|
|
|
| lgpSysEventDescription |
1.3.6.1.4.1.476.1.42.3.7.7 |
| An ASCII textual description for the event. This object is
primarily used in the varbind of some notifications to provide
a simple human-readable description. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(255) |
|
| lgpSysEventNotifications |
1.3.6.1.4.1.476.1.42.3.7.8 |
| This sub-tree is used to register Liebert System Notification object
identifiers. |
| Status: current |
Access: read-only |
| OBJECT-IDENTITY |
|
|
|
| lgpSysDeviceComponentGroup |
1.3.6.1.4.1.476.1.42.3.7.9 |
| This sub-tree registers well known device components. |
| Status: current |
Access: read-only |
| OBJECT-IDENTITY |
|
|
|
| lgpSysDeviceComponentTable |
1.3.6.1.4.1.476.1.42.3.7.9.1 |
| A list of components of devices identified by their serial number and
or model number.
This table contains zero, one, or many rows. The NMS cannot create or
delete rows from the table. The rows are created by the agent based upon
the capabilities of the managed device. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
LgpSysDeviceComponentEntry |
|
| lgpSysDeviceComponentEntry |
1.3.6.1.4.1.476.1.42.3.7.9.1.1 |
| This entry defines the contents of the columns for the table
'lgpSysDeviceComponentTable'. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
LgpSysDeviceComponentEntry |
|
|
| lgpSysDeviceComponentIndex |
1.3.6.1.4.1.476.1.42.3.7.9.1.1.1 |
| This is the index indicating the row in the table
'lgpSysDeviceComponentTable' for a component entry. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| lgpSysDeviceComponentDescr |
1.3.6.1.4.1.476.1.42.3.7.9.1.1.2 |
| An OID representing a component of the device indicated by the
index lgpAgentDeviceIndex. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
OBJECT IDENTIFIER |
|
|
| lgpSysDeviceComponentSerialNum |
1.3.6.1.4.1.476.1.42.3.7.9.1.1.3 |
| This is the serial number of the component described by the OID
'lgpSysDeviceComponentDescr'. This data is intended for
display / human consumption. Do not use this field for determining
programmatic behavior. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(255) |
|
| lgpSysDeviceComponentModelNum |
1.3.6.1.4.1.476.1.42.3.7.9.1.1.4 |
| This is the model identifier of the component described by the OID
'lgpSysDeviceComponentDescr'. This data is intended for
display / human consumption. Do not use this field for determining
programmatic behavior. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(255) |
|
| lgpSysDeviceComponentWellknown |
1.3.6.1.4.1.476.1.42.3.7.9.5 |
| This sub-tree registers well known Liebert System Components. |
| Status: current |
Access: read-only |
| OBJECT-IDENTITY |
|
|
|
| lgpSysDeviceBatCabinet |
1.3.6.1.4.1.476.1.42.3.7.9.5.5 |
| This sub-tree is used to register a battery cabinet component.
To determine the cabinet being described in a
multi-cabinet system, this point implements an additional
two indexes. The first index describes the module the cabinet
is located in. The second index describes the cabinet
number. In an SMS (Single-Module System) the first index is
always 1.
Example: lgpSysDeviceComponentCabinet.2.4
'lgpSysDeviceCabinet' = Point is a battery cabinet.
'.2' = Cabinet is in the second module.
'.4' = Cabinet number 4 in second module |
| Status: current |
Access: read-only |
| OBJECT-IDENTITY |
|
|
|
| lgpSysDeviceParallelCabinet |
1.3.6.1.4.1.476.1.42.3.7.9.5.6 |
| This sub-tree is used to register a parallel cabinet. |
| Status: current |
Access: read-only |
| OBJECT-IDENTITY |
|
|
|
| lgpSysDeviceMaintBypass |
1.3.6.1.4.1.476.1.42.3.7.9.5.7 |
| This sub-tree is used to register the maintenance bypass. |
| Status: current |
Access: read-only |
| OBJECT-IDENTITY |
|
|
|
| lgpSysNotification |
1.3.6.1.4.1.476.1.42.3.7.8.1 |
| This notification is a generic notification intended for direct user
visibility. The user event description identifies the system
condition that has occurred. This text will be prefixed with either
'Active:', 'Cleared:', or 'Message:' depending on the state of the
event. Note: That a prefix of 'Message:' identifies a stateless event
and as such there will be no corresponding 'Cleared:' trap sent. |
| Status: current |
Access: read-only |
| NOTIFICATION-TYPE |
|
|
|
| lgpSysNormal |
1.3.6.1.4.1.476.1.42.3.7.8.2 |
| The system has returned to a normal operating state. This implies
prior to the generation of this event the system was operating in a
state where one or more alarm or warning conditions were present.
All of those alarms or conditions have now cleared.
NOTE: This notification may be generated after a short delay during a
cold boot of the system -- if no alarms or conditions are present in the
monitored device(s) at that time. |
| Status: current |
Access: read-only |
| NOTIFICATION-TYPE |
|
|
|
| lgpSysSelfTestResult |
1.3.6.1.4.1.476.1.42.3.7.2.1 |
| The outcome of the previous self-test. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
unknown(1), passed(2), failed(3), inProgress(4), sysFailure(5), inhibited(6) |
|
| lgpSysState |
1.3.6.1.4.1.476.1.42.3.7.2.2 |
| The operating status for the system. The intent of this data
is to provide a high level status of the system.
The possible states are:
normalOperation(1)
The system is operating normally with no active warnings or
alarms.
startUp(2)
The system is in a startup state (initializing). Monitoring
operations and information may not be fully supported at this
time. This state will clear automatically when the system is
fully initialized and ready to accept monitoring commands.
normalWithWarning(3)
The system is operating normally with one or more active
warnings. Appropriate personnel should investigate the
warning(s) as soon as possible and take appropriate action.
normalWithAlarm(4)
The system is operating normally with one or more active
alarms. Appropriate personnel should investigate the alarm(s)
as soon as possible and take appropriate action.
abnormalOperation(5)
They system is operating abnormally. There is a
failure within the system that is unexpected under normal
operating conditions. Appropriate personnel should investigate
the cause as soon as possible. The normal functioning of
the system is likely inhibited. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
normalOperation(1), startUp(2), normalWithWarning(3), normalWithAlarm(4), abnormalOperation(5) |
|
| lgpSysAudibleAlarm |
1.3.6.1.4.1.476.1.42.3.7.3.1 |
| The state of the audible alarm of the device. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
on(1), off(2) |
|
| lgpSysSelfTest |
1.3.6.1.4.1.476.1.42.3.7.4.1 |
| Self-Test Command. This command will initiate a system self-test of
the system. If already initiated, this command will abort the
self-test. This command should be sent with a parameter of 1. This
variable doesn't return a value when read. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| lgpSysControlOperationOnOff |
1.3.6.1.4.1.476.1.42.3.7.4.2 |
| This object allows control of the system functionality. This will not
affect the communications or control of the system, so that once turned
off, the system operation can be restored by setting this value to
'on'. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
on(1), off(2) |
|
| lgpSysTimeEpoch |
1.3.6.1.4.1.476.1.42.3.7.5.1 |
| The present time of the system. This time is represented as the
number of seconds since the epoch of 1970-01-01 00:00:00 GMT. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| lgpSysMaintenanceCapacity |
1.3.6.1.4.1.476.1.42.3.7.6.1 |
| The relative percentage of time that has elapsed since the last
scheduled maintenance was performed. When this value reaches 100%,
the device is due for another scheduled maintenance procedure. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| lgpSysMaintenanceYear |
1.3.6.1.4.1.476.1.42.3.7.6.2 |
| The year in which the next scheduled service is due |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| lgpSysMaintenanceMonth |
1.3.6.1.4.1.476.1.42.3.7.6.3 |
| The month in which the next scheduled service is due |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|