LLDP-V2-MIB

File: LLDP-V2-MIB.mib (79792 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMP-FRAMEWORK-MIB
SNMPv2-CONF RMON2-MIB IANA-ADDRESS-FAMILY-NUMBERS-MIB
IF-MIB LLDP-V2-TC-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
Counter32 NOTIFICATION-TYPE TimeStamp
TruthValue MacAddress RowStatus
SnmpAdminString MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP TimeFilter ZeroBasedCounter32
AddressFamilyNumbers ifGeneralInformationGroup InterfaceIndex
LldpV2ChassisIdSubtype LldpV2ChassisId LldpV2PortIdSubtype
LldpV2PortId LldpV2ManAddrIfSubtype LldpV2ManAddress
LldpV2SystemCapabilitiesMap LldpV2DestAddressTableIndex ieee802dot1mibs

Defined Types

LldpV2PortConfigEntry  
SEQUENCE    
  lldpV2PortConfigIfIndex InterfaceIndex
  lldpV2PortConfigDestAddressIndex LldpV2DestAddressTableIndex
  lldpV2PortConfigAdminStatus INTEGER
  lldpV2PortConfigNotificationEnable TruthValue
  lldpV2PortConfigTLVsTxEnable BITS

LldpV2DestAddressTableEntry  
SEQUENCE    
  lldpV2AddressTableIndex LldpV2DestAddressTableIndex
  lldpV2DestMacAddress MacAddress

LldpV2ManAddrConfigTxPortsEntry  
SEQUENCE    
  lldpV2ManAddrConfigIfIndex InterfaceIndex
  lldpV2ManAddrConfigDestAddressIndex LldpV2DestAddressTableIndex
  lldpV2ManAddrConfigLocManAddrSubtype AddressFamilyNumbers
  lldpV2ManAddrConfigLocManAddr LldpV2ManAddress
  lldpV2ManAddrConfigTxEnable TruthValue
  lldpV2ManAddrConfigRowStatus RowStatus

LldpV2StatsTxPortEntry  
SEQUENCE    
  lldpV2StatsTxIfIndex InterfaceIndex
  lldpV2StatsTxDestMACAddress LldpV2DestAddressTableIndex
  lldpV2StatsTxPortFramesTotal Counter32
  lldpV2StatsTxLLDPDULengthErrors Counter32

LldpV2StatsRxPortEntry  
SEQUENCE    
  lldpV2StatsRxDestIfIndex InterfaceIndex
  lldpV2StatsRxDestMACAddress LldpV2DestAddressTableIndex
  lldpV2StatsRxPortFramesDiscardedTotal Counter32
  lldpV2StatsRxPortFramesErrors Counter32
  lldpV2StatsRxPortFramesTotal Counter32
  lldpV2StatsRxPortTLVsDiscardedTotal Counter32
  lldpV2StatsRxPortTLVsUnrecognizedTotal Counter32
  lldpV2StatsRxPortAgeoutsTotal ZeroBasedCounter32

LldpV2LocPortEntry  
SEQUENCE    
  lldpV2LocPortIfIndex InterfaceIndex
  lldpV2LocPortIdSubtype LldpV2PortIdSubtype
  lldpV2LocPortId LldpV2PortId
  lldpV2LocPortDesc SnmpAdminString

LldpV2LocManAddrEntry  
SEQUENCE    
  lldpV2LocManAddrSubtype AddressFamilyNumbers
  lldpV2LocManAddr LldpV2ManAddress
  lldpV2LocManAddrLen Unsigned32
  lldpV2LocManAddrIfSubtype LldpV2ManAddrIfSubtype
  lldpV2LocManAddrIfId Unsigned32
  lldpV2LocManAddrOID OBJECT IDENTIFIER

LldpV2RemEntry  
SEQUENCE    
  lldpV2RemTimeMark TimeFilter
  lldpV2RemLocalIfIndex InterfaceIndex
  lldpV2RemLocalDestMACAddress LldpV2DestAddressTableIndex
  lldpV2RemIndex Unsigned32
  lldpV2RemChassisIdSubtype LldpV2ChassisIdSubtype
  lldpV2RemChassisId LldpV2ChassisId
  lldpV2RemPortIdSubtype LldpV2PortIdSubtype
  lldpV2RemPortId LldpV2PortId
  lldpV2RemPortDesc SnmpAdminString
  lldpV2RemSysName SnmpAdminString
  lldpV2RemSysDesc SnmpAdminString
  lldpV2RemSysCapSupported LldpV2SystemCapabilitiesMap
  lldpV2RemSysCapEnabled LldpV2SystemCapabilitiesMap
  lldpV2RemRemoteChanges TruthValue
  lldpV2RemTooManyNeighbors TruthValue

LldpV2RemManAddrEntry  
SEQUENCE    
  lldpV2RemManAddrSubtype AddressFamilyNumbers
  lldpV2RemManAddr LldpV2ManAddress
  lldpV2RemManAddrIfSubtype LldpV2ManAddrIfSubtype
  lldpV2RemManAddrIfId Unsigned32
  lldpV2RemManAddrOID OBJECT IDENTIFIER

LldpV2RemUnknownTLVEntry  
SEQUENCE    
  lldpV2RemUnknownTLVType Unsigned32
  lldpV2RemUnknownTLVInfo OCTET STRING

LldpV2RemOrgDefInfoEntry  
SEQUENCE    
  lldpV2RemOrgDefInfoOUI OCTET STRING
  lldpV2RemOrgDefInfoSubtype Unsigned32
  lldpV2RemOrgDefInfoIndex Unsigned32
  lldpV2RemOrgDefInfo OCTET STRING

Defined Values

lldpV2MIB 1.3.111.2.802.1.1.13
Management Information Base module for LLDP configuration, statistics, local system data and remote systems data components. This MIB module supports the architecture described in Clause 6, where multiple LLDP agents can be associated with a single Port, each supporting transmission by means of a different MAC address. Unless otherwise indicated, the references in this MIB module are to IEEE 802.1AB-2009. Copyright (C) IEEE (2009). This version of this MIB module is published as subclause 11.5.2 of IEEE Std 802.1AB-2009; see the standard itself for full legal notices.
MODULE-IDENTITY    

lldpV2Notifications 1.3.111.2.802.1.1.13.0
OBJECT IDENTIFIER    

lldpV2Objects 1.3.111.2.802.1.1.13.1
OBJECT IDENTIFIER    

lldpV2Conformance 1.3.111.2.802.1.1.13.2
OBJECT IDENTIFIER    

lldpV2Configuration 1.3.111.2.802.1.1.13.1.1
OBJECT IDENTIFIER    

lldpV2Statistics 1.3.111.2.802.1.1.13.1.2
OBJECT IDENTIFIER    

lldpV2LocalSystemData 1.3.111.2.802.1.1.13.1.3
OBJECT IDENTIFIER    

lldpV2RemoteSystemsData 1.3.111.2.802.1.1.13.1.4
OBJECT IDENTIFIER    

lldpV2Extensions 1.3.111.2.802.1.1.13.1.5
OBJECT IDENTIFIER    

lldpV2MessageTxInterval 1.3.111.2.802.1.1.13.1.1.1
The interval at which LLDP frames are transmitted on behalf of this LLDP agent. The default value for lldpV2MessageTxInterval object is 30 seconds. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 5..32768  

lldpV2MessageTxHoldMultiplier 1.3.111.2.802.1.1.13.1.1.2
The time-to-live value expressed as a multiple of the lldpV2MessageTxInterval object. The actual time-to-live value used in LLDP frames, transmitted on behalf of this LLDP agent, can be expressed by the following formula: TTL = min(65535, (lldpV2MessageTxInterval * lldpV2MessageTxHoldMultiplier)) For example, if the value of lldpV2MessageTxInterval is '30', and the value of lldpV2MessageTxHoldMultiplier is '4', then the value '120' is encoded in the TTL field in the LLDP header. The default value for lldpV2MessageTxHoldMultiplier object is 4. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 2..10  

lldpV2ReinitDelay 1.3.111.2.802.1.1.13.1.1.3
The lldpV2ReinitDelay indicates the delay (in units of seconds) from when lldpPortConfigAdminStatus object of a particular port becomes 'disabled' until re-initialization is attempted. The default value for lldpV2ReinitDelay is two seconds. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..10  

lldpV2NotificationInterval 1.3.111.2.802.1.1.13.1.1.4
This object controls the interval between transmission of LLDP notifications during normal transmission periods. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 5..3600  

lldpV2TxCreditMax 1.3.111.2.802.1.1.13.1.1.5
The maximum number of consecutive LLDPDUs that can be transmitted at any time. The default value for lldpV2TxCreditMax object is 5 PDUs. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..100  

lldpV2MessageFastTx 1.3.111.2.802.1.1.13.1.1.6
The interval at which LLDP frames are transmitted on behalf of this LLDP agent during fast transmission period (e.g. when a new neighbor is detected). The default value for lldpV2MessageFastTx object is 1 second. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..3600  

lldpV2TxFastInit 1.3.111.2.802.1.1.13.1.1.7
The initial value used to initialize the txFast variable which determines the number of transmissions that are made in fast transmission mode. The default value for lldpV2TxFastInit object is 4. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..8  

lldpV2PortConfigTable 1.3.111.2.802.1.1.13.1.1.8
The table that controls LLDP frame transmission on individual ports and using particular destination MAC addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LldpV2PortConfigEntry

lldpV2PortConfigEntry 1.3.111.2.802.1.1.13.1.1.8.1
LLDP configuration information for a particular port and destination MAC address. This configuration parameter controls the transmission and the reception of LLDP frames on those interface/address combinations whose rows are created in this table. Rows in this table can only be created for MAC addresses that can validly be used in association with the type of interface concerned, as defined by table 8-2. The contents of this table is persistent across re-initializations or re-boots.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2PortConfigEntry  

lldpV2PortConfigIfIndex 1.3.111.2.802.1.1.13.1.1.8.1.1
The interface index value used to identify the port associated with this entry. Its value is an index into the interfaces MIB. The value of this object is used as an index to the lldpV2PortConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

lldpV2PortConfigDestAddressIndex 1.3.111.2.802.1.1.13.1.1.8.1.2
The index value used to identify the destination MAC address associated with this entry. Its value identifies the row in the lldpV2DestAddressTable where the MAC address can be found. The value of this object is used as an index to the lldpV2PortConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2DestAddressTableIndex  

lldpV2PortConfigAdminStatus 1.3.111.2.802.1.1.13.1.1.8.1.3
The administratively desired status of the local LLDP agent. If the associated lldpV2PortConfigAdminStatus object is set to a value of 'txOnly(1)', then LLDP agent transmits LLDPframes on this port and it does not store any information about the remote systems connected. If the associated lldpV2PortConfigAdminStatus object is set to a value of 'rxOnly(2)', then the LLDP agent receives, but it does not transmit LLDP frames on this port. If the associated lldpV2PortConfigAdminStatus object is set to a value of 'txAndRx(3)', then the LLDP agent transmits and receives LLDP frames on this port. If the associated lldpV2PortConfigAdminStatus object is set to a value of 'disabled(4)', then LLDP agent does not transmit or receive LLDP frames on this port. If there is remote systems information which is received on this port and stored in other tables, before the port's lldpV2PortConfigAdminStatus becomes disabled, then that information is deleted.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER txOnly(1), rxOnly(2), txAndRx(3), disabled(4)  

lldpV2PortConfigNotificationEnable 1.3.111.2.802.1.1.13.1.1.8.1.4
The lldpV2PortConfigNotificationEnable controls, on a per agent basis, whether or not notifications from the agent are enabled. The value true(1) means that notifications are enabled; the value false(2) means that they are not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

lldpV2PortConfigTLVsTxEnable 1.3.111.2.802.1.1.13.1.1.8.1.5
The lldpV2PortConfigTLVsTxEnable, defined as a bitmap, includes the basic set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network management. Each bit in the bitmap corresponds to a TLV type associated with a specific optional TLV. It should be noted that the organizationally-specific TLVs are excluded from the lldpV2PortConfigTLVsTxEnable bitmap. LLDP Organization Specific Information Extension MIBs should have similar configuration object to control transmission of their organizationally defined TLVs. The bit 'portDesc(0)' indicates that LLDP agent should transmit 'Port Description TLV'. The bit 'sysName(1)' indicates that LLDP agent should transmit 'System Name TLV'. The bit 'sysDesc(2)' indicates that LLDP agent should transmit 'System Description TLV'. The bit 'sysCap(3)' indicates that LLDP agent should transmit 'System Capabilities TLV'. There is no bit reserved for the management address TLV type since transmission of management address TLVs are controlled by another object, lldpV2ConfigManAddrTable. The default value for lldpV2PortConfigTLVsTxEnable object is empty set, which means no enumerated values are set. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
Status: current Access: read-write
OBJECT-TYPE    
  BITS portDesc(0), sysName(1), sysDesc(2), sysCap(3)  

lldpV2DestAddressTable 1.3.111.2.802.1.1.13.1.1.9
The table that contains the set of MAC addresses used by LLDP for transmission and reception of LLDPDUs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LldpV2DestAddressTableEntry

lldpV2DestAddressTableEntry 1.3.111.2.802.1.1.13.1.1.9.1
Destination MAC address information for LLDP. This configuration parameter identifies a MAC address corresponding to a LldpV2DestAddressTableIndex value. Rows in this table are created as necessary, to support MAC addresses needed by other tables in the MIB that are indexed by MAC address. A given row in this table cannot be deleted if the MAC address table index value is in use in any other table in the MIB. The contents of this table is persistent aacross re-initializations or re-boots.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2DestAddressTableEntry  

lldpV2AddressTableIndex 1.3.111.2.802.1.1.13.1.1.9.1.1
The index value used to identify the destination MAC address associated with this entry. The value of this object is used as an index to the lldpV2DestAddressTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2DestAddressTableIndex  

lldpV2DestMacAddress 1.3.111.2.802.1.1.13.1.1.9.1.2
The MAC address associated with this entry. The octet string identifies an individual or a group MAC address that is in use by LLDP as a destination MAC address. The MAC address is encoded in the octet string in canonical format (see IEEE Std 802).
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

lldpV2ManAddrConfigTxPortsTable 1.3.111.2.802.1.1.13.1.1.10
The table that controls selection of LLDP management address TLV instances to be transmitted on individual port/ destination address pairs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LldpV2ManAddrConfigTxPortsEntry

lldpV2ManAddrConfigTxPortsEntry 1.3.111.2.802.1.1.13.1.1.10.1
LLDP configuration information that specifies the set of port/destination address pairs on which the local system management address instance is transmitted. Each active lldpManAddrConfigTxPortsTableV2Entry is restored from non-volatile storage and re-created after a re-initialization of the management system.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2ManAddrConfigTxPortsEntry  

lldpV2ManAddrConfigIfIndex 1.3.111.2.802.1.1.13.1.1.10.1.1
The interface index value used to identify the port associated with this entry. Its value is an index into the interfaces MIB. The value of this object is used as an index to the lldpV2PortConfigTable. The value in this column of the table MUST match the IfIndex value specified in the BridgePort table.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

lldpV2ManAddrConfigDestAddressIndex 1.3.111.2.802.1.1.13.1.1.10.1.2
The index value used to identify the destination MAC address associated with this entry. Its value identifies the row in the lldpV2DestAddressTable where the MAC address can be found. The value of this object is used as an index to the lldpV2PortConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2DestAddressTableIndex  

lldpV2ManAddrConfigLocManAddrSubtype 1.3.111.2.802.1.1.13.1.1.10.1.3
The type of management address identifier encoding used in the associated 'lldpLocManagmentAddr' object. It should be noted that only a subset of the possible address encodings enumerated in AddressFamilyNumbers are appropriate for use as a LLDP management address, either because some are just not apliccable or because the maximum size of a LldpV2ManAddress octet string would prevent the use of some address identifier encodings.
Status: current Access: not-accessible
OBJECT-TYPE    
  AddressFamilyNumbers  

lldpV2ManAddrConfigLocManAddr 1.3.111.2.802.1.1.13.1.1.10.1.4
The string value used to identify the management address component associated with the local system. The purpose of this address is to contact the management entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2ManAddress  

lldpV2ManAddrConfigTxEnable 1.3.111.2.802.1.1.13.1.1.10.1.5
A boolean controlling the transmission of system management address instance for the specified port, destination, subtype and MAN address used to index this table. If set to the default value of false, no transmission occurs. If set to true, the appropriate information is transmitted out of the port specified in the row's index.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

lldpV2ManAddrConfigRowStatus 1.3.111.2.802.1.1.13.1.1.10.1.6
Indicates the status of an entry in this table, and is used to create/delete entries. The corresponding instances of the following objects must be set before this object can be made active(1): lldpV2ManAddrConfigDestAddressIndex lldpV2ManAddrConfigLocManAddrSubtype lldpV2ManAddrConfigLocManAddr lldpV2ManAddrConfigTxEnable The corresponding instances of the following objects may not be changed while this object is active(1): lldpV2ManAddrConfigDestAddressIndex lldpV2ManAddrConfigLocManAddrSubtype lldpV2ManAddrConfigLocManAddr
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

lldpV2StatsRemTablesLastChangeTime 1.3.111.2.802.1.1.13.1.2.1
The value of sysUpTime object (defined in IETF RFC 3418) at the time an entry is created, modified, or deleted in the in tables associated with the lldpV2RemoteSystemsData objects and all LLDP extension objects associated with remote systems. An NMS can use this object to reduce polling of the lldpV2RemoteSystemsData objects.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

lldpV2StatsRemTablesInserts 1.3.111.2.802.1.1.13.1.2.2
The number of times the complete set of information advertised by a particular MSAP has been inserted into tables contained in lldpV2RemoteSystemsData and lldpV2Extensions objects. The complete set of information received from a particular MSAP should be inserted into related tables. If partial information cannot be inserted for a reason such as lack of resources, all of the complete set of information should be removed. This counter should be incremented only once after the complete set of information is successfully recorded in all related tables. Any failures during inserting information set which result in deletion of previously inserted information should not trigger any changes in lldpV2StatsRemTablesInserts since the insert is not completed yet or in lldpStatsRemTablesDeletes, since the deletion would only be a partial deletion. If the failure was the result of lack of resources, the lldpStatsRemTablesDrops counter should be incremented once.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

lldpV2StatsRemTablesDeletes 1.3.111.2.802.1.1.13.1.2.3
The number of times the complete set of information advertised by a particular MSAP has been deleted from tables contained in lldpV2RemoteSystemsData and lldpV2Extensions objects. This counter should be incremented only once when the complete set of information is completely deleted from all related tables. Partial deletions, such as deletion of rows associated with a particular MSAP from some tables, but not from all tables are not allowed, thus should not change the value of this counter.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

lldpV2StatsRemTablesDrops 1.3.111.2.802.1.1.13.1.2.4
The number of times the complete set of information advertised by a particular MSAP could not be entered into tables contained in lldpV2RemoteSystemsData and lldpV2Extensions objects because of insufficient resources.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

lldpV2StatsRemTablesAgeouts 1.3.111.2.802.1.1.13.1.2.5
The number of times the complete set of information advertised by a particular MSAP has been deleted from tables contained in lldpV2RemoteSystemsData and lldpV2Extensions objects because the information timeliness interval has expired. This counter should be incremented only once when the complete set of information is completely invalidated (aged out) from all related tables. Partial ageing, similar to deletion case, is not allowed, and thus, should not change the value of this counter.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

lldpV2StatsTxPortTable 1.3.111.2.802.1.1.13.1.2.6
A table containing LLDP transmission statistics for individual port/destination address combinations. Entries are not required to exist in this table while the lldpPortConfigEntry object is equal to 'disabled(4)'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LldpV2StatsTxPortEntry

lldpV2StatsTxPortEntry 1.3.111.2.802.1.1.13.1.2.6.1
LLDP frame transmission statistics for a particular port and destination MAC address. The port is contained in the same chassis as the LLDP agent. All counter values in a particular entry shall be maintained on a continuing basis and shall not be deleted upon expiration of rxInfoTTL timing counters in the LLDP remote systems MIB of the receipt of a shutdown frame from a remote LLDP agent. All statistical counters associated with a particular port on the local LLDP agent become frozen whenever the adminStatus is disabled for the same port. Rows in this table can only be created for MAC addresses that can validly be used in association with the type of interface concerned, as defined by table 8-2.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2StatsTxPortEntry  

lldpV2StatsTxIfIndex 1.3.111.2.802.1.1.13.1.2.6.1.1
The interface index value used to identify the port associated with this entry. Its value is an index into the interfaces MIB The value of this object is used as an index to the lldpV2StatsTxPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

lldpV2StatsTxDestMACAddress 1.3.111.2.802.1.1.13.1.2.6.1.2
The index value used to identify the destination MAC address associated with this entry. Its value identifies the row in the lldpV2DestAddressTable where the MAC address can be found. The value of this object is used as an index to the lldpV2StatsTxPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2DestAddressTableIndex  

lldpV2StatsTxPortFramesTotal 1.3.111.2.802.1.1.13.1.2.6.1.3
The number of LLDP frames transmitted by this LLDP agent on the indicated port to the destination MAC address associated with this row of the table.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

lldpV2StatsTxLLDPDULengthErrors 1.3.111.2.802.1.1.13.1.2.6.1.4
The number of LLDPDU Length Errors recorded for the Port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

lldpV2StatsRxPortTable 1.3.111.2.802.1.1.13.1.2.7
A table containing LLDP reception statistics for individual ports and destination MAC addresses. Entries are not required to exist in this table while the lldpPortConfigEntry object is equal to 'disabled(4)'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LldpV2StatsRxPortEntry

lldpV2StatsRxPortEntry 1.3.111.2.802.1.1.13.1.2.7.1
LLDP frame reception statistics for a particular port. The port is contained in the same chassis as the LLDP agent. All counter values in a particular entry shall be maintained on a continuing basis and shall not be deleted upon expiration of rxInfoTTL timing counters in the LLDP remote systems MIB of the receipt of a shutdown frame from a remote LLDP agent. All statistical counters associated with a particular port on the local LLDP agent become frozen whenever the adminStatus is disabled for the same port. Rows in this table can only be created for MAC addresses that can validly be used in association with the type of interface concerned, as defined by table 8-2. The contents of this table is persistent across re-initializations or re-boots.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2StatsRxPortEntry  

lldpV2StatsRxDestIfIndex 1.3.111.2.802.1.1.13.1.2.7.1.1
The interface index value used to identify the port associated with this entry. Its value is an index into the interfaces MIB The value of this object is used as an index to the lldpStatsRxPortV2Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

lldpV2StatsRxDestMACAddress 1.3.111.2.802.1.1.13.1.2.7.1.2
The index value used to identify the destination MAC address associated with this entry. Its value identifies the row in the lldpV2DestAddressTable where the MAC address can be found. The value of this object is used as an index to the lldpStatsRxPortV2Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2DestAddressTableIndex  

lldpV2StatsRxPortFramesDiscardedTotal 1.3.111.2.802.1.1.13.1.2.7.1.3
The number of LLDP frames received by this LLDP agent on the indicated port, and then discarded for any reason. This counter can provide an indication that LLDP header formatting problems may exist with the local LLDP agent in the sending system or that LLDPDU validation problems may exist with the local LLDP agent in the receiving system.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

lldpV2StatsRxPortFramesErrors 1.3.111.2.802.1.1.13.1.2.7.1.4
The number of invalid LLDP frames received by this LLDP agent on the indicated port, while this LLDP agent is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

lldpV2StatsRxPortFramesTotal 1.3.111.2.802.1.1.13.1.2.7.1.5
The number of valid LLDP frames received by this LLDP agent on the indicated port, while this LLDP agent is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

lldpV2StatsRxPortTLVsDiscardedTotal 1.3.111.2.802.1.1.13.1.2.7.1.6
The number of LLDP TLVs discarded for any reason by this LLDP agent on the indicated port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

lldpV2StatsRxPortTLVsUnrecognizedTotal 1.3.111.2.802.1.1.13.1.2.7.1.7
The number of LLDP TLVs received on the given port that are not recognized by this LLDP agent on the indicated port. An unrecognized TLV is referred to as the TLV whose type value is in the range of reserved TLV types (000 1001 - 111 1110) in Table 9.1 of IEEE Std 802.1AB-2004. An unrecognized TLV may be a basic management TLV from a later LLDP version.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

lldpV2StatsRxPortAgeoutsTotal 1.3.111.2.802.1.1.13.1.2.7.1.8
The counter that represents the number of age-outs that occurred on a given port. An age-out is the number of times the complete set of information advertised by a particular MSAP has been deleted from tables contained in lldpV2RemoteSystemsData and lldpV2Extensions objects because the information timeliness interval has expired. This counter is similar to lldpV2StatsRemTablesAgeouts, except that the counter is on a per port basis. This enables NMS to poll tables associated with the lldpV2RemoteSystemsData objects and all LLDP extension objects associated with remote systems on the indicated port only. This counter is set to zero during agent initialization and its value should not be saved in non-volatile storage. This counter is incremented only once when the complete set of information is invalidated (aged out) from all related tables on a particular port. Partial ageing is not allowed.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

lldpV2LocChassisIdSubtype 1.3.111.2.802.1.1.13.1.3.1
The type of encoding used to identify the chassis associated with the local system.
Status: current Access: read-only
OBJECT-TYPE    
  LldpV2ChassisIdSubtype  

lldpV2LocChassisId 1.3.111.2.802.1.1.13.1.3.2
The string value used to identify the chassis component associated with the local system.
Status: current Access: read-only
OBJECT-TYPE    
  LldpV2ChassisId  

lldpV2LocSysName 1.3.111.2.802.1.1.13.1.3.3
The string value used to identify the system name of the local system. If the local agent supports IETF RFC 3418, lldpLocSysName object should have the same value of sysName object.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

lldpV2LocSysDesc 1.3.111.2.802.1.1.13.1.3.4
The string value used to identify the system description of the local system. If the local agent supports IETF RFC 3418, lldpLocSysDesc object should have the same value of sysDesc object.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

lldpV2LocSysCapSupported 1.3.111.2.802.1.1.13.1.3.5
The bitmap value used to identify which system capabilities are supported on the local system.
Status: current Access: read-only
OBJECT-TYPE    
  LldpV2SystemCapabilitiesMap  

lldpV2LocSysCapEnabled 1.3.111.2.802.1.1.13.1.3.6
The bitmap value used to identify which system capabilities are enabled on the local system.
Status: current Access: read-only
OBJECT-TYPE    
  LldpV2SystemCapabilitiesMap  

lldpV2LocPortTable 1.3.111.2.802.1.1.13.1.3.7
This table contains one row per port of information associated with the local system known to this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LldpV2LocPortEntry

lldpV2LocPortEntry 1.3.111.2.802.1.1.13.1.3.7.1
Information about a particular port component. Entries may be created and deleted in this table by the agent. Rows in this table can only be created for MAC addresses that can validly be used in association with the type of interface concerned, as defined by table 8-2. The contents of this table is persistent across re-initializations or re-boots.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2LocPortEntry  

lldpV2LocPortIfIndex 1.3.111.2.802.1.1.13.1.3.7.1.1
The interface index value used to identify the port associated with this entry. Its value is an index into the interfaces MIB The value of this object is used as an index to the lldpV2LocPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

lldpV2LocPortIdSubtype 1.3.111.2.802.1.1.13.1.3.7.1.2
The type of port identifier encoding used in the associated 'lldpLocPortId' object.
Status: current Access: read-only
OBJECT-TYPE    
  LldpV2PortIdSubtype  

lldpV2LocPortId 1.3.111.2.802.1.1.13.1.3.7.1.3
The string value used to identify the port component associated with a given port in the local system.
Status: current Access: read-only
OBJECT-TYPE    
  LldpV2PortId  

lldpV2LocPortDesc 1.3.111.2.802.1.1.13.1.3.7.1.4
The string value used to identify the IEEE 802 LAN station's port description associated with the local system. If the local agent supports IETF RFC 2863, lldpLocPortDesc object should have the same value of ifDescr object.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

lldpV2LocManAddrTable 1.3.111.2.802.1.1.13.1.3.8
This table contains management address information on the local system known to this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LldpV2LocManAddrEntry

lldpV2LocManAddrEntry 1.3.111.2.802.1.1.13.1.3.8.1
Management address information about a particular chassis component. There may be multiple management addresses configured on the system identified by a particular lldpLocChassisId. Each management address should have distinct 'management address type' (lldpV2LocManAddrSubtype) and 'management address' (lldpLocManAddr.) Entries may be created and deleted in this table by the agent. Since a variable length octetstring is used as an index in a table, the address length is encoded as part of the OID (as per IETF RFC 2578).
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2LocManAddrEntry  

lldpV2LocManAddrSubtype 1.3.111.2.802.1.1.13.1.3.8.1.1
The type of management address identifier encoding used in the associated 'lldpLocManagmentAddr' object. It should be noted that only a subset of the possible address encodings enumerated in AddressFamilyNumbers are appropriate for use as a LLDP management address, either because some are just not apliccable or because the maximum size of a LldpV2ManAddress octet string would prevent the use of some address identifier encodings.
Status: current Access: not-accessible
OBJECT-TYPE    
  AddressFamilyNumbers  

lldpV2LocManAddr 1.3.111.2.802.1.1.13.1.3.8.1.2
The string value used to identify the management address component associated with the local system. The purpose of this address is to contact the management entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2ManAddress  

lldpV2LocManAddrLen 1.3.111.2.802.1.1.13.1.3.8.1.3
The total length of the management address subtype and the management address fields in LLDPDUs transmitted by the local LLDP agent. The management address length field is needed so that the receiving systems that do not implement SNMP are not required to implement an iana family numbers/address length equivalency table in order to decode the management address.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

lldpV2LocManAddrIfSubtype 1.3.111.2.802.1.1.13.1.3.8.1.4
The enumeration value that identifies the interface numbering method used for defining the interface number (lldpV2LocManAddrIfId), associated with the local system.
Status: current Access: read-only
OBJECT-TYPE    
  LldpV2ManAddrIfSubtype  

lldpV2LocManAddrIfId 1.3.111.2.802.1.1.13.1.3.8.1.5
The integer value used to identify the interface number regarding the management address component associated with the local system.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

lldpV2LocManAddrOID 1.3.111.2.802.1.1.13.1.3.8.1.6
The OID value used to identify the type of hardware component or protocol entity associated with the management address advertised by the local system agent.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

lldpV2RemTable 1.3.111.2.802.1.1.13.1.4.1
This table contains one or more rows per physical network connection known to this agent. The agent may wish to ensure that only one lldpRemEntry is present for each local port and destination MAC address, or it may choose to maintain multiple lldpRemEntries for the same local port and destination MAC address. The following procedure may be used to retrieve remote systems information updates from an LLDP agent: 1. NMS polls all tables associated with remote systems and keeps a local copy of the information retrieved. NMS polls periodically the values of the following objects: a. lldpV2StatsRemTablesInserts b. lldpV2StatsRemTablesDeletes c. lldpV2StatsRemTablesDrops d. lldpV2StatsRemTablesAgeouts e. lldpV2StatsRxPortAgeoutsTotal for all ports. 2. LLDP agent updates remote systems MIB objects, and sends out notifications to a list of notification destinations. 3. NMS receives the notifications and compares the new values of objects listed in step 1. Periodically, NMS should poll the object lldpV2StatsRemTablesLastChangeTime to find out if anything has changed since the last poll. if something has changed, NMS polls the objects listed in step 1 to figure out what kind of changes occurred in the tables. if value of lldpV2StatsRemTablesInserts has changed, then NMS walks all tables by employing TimeFilter with the last-polled time value. This request returns new objects or objects whose values have been updated since the last poll. if value of lldpV2StatsRemTablesAgeouts has changed, then NMS walks the lldpStatsRxPortAgeoutsTotal and compares the new values with previously recorded ones. For ports whose lldpStatsRxPortAgeoutsTotal value is greater than the recorded value, NMS can retrieve objects associated with those ports from table(s) without employing a TimeFilter (which is performed by specifying 0 for the TimeFilter.) lldpV2StatsRemTablesDeletes and lldpV2StatsRemTablesDrops objects are provided for informational purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LldpV2RemEntry

lldpV2RemEntry 1.3.111.2.802.1.1.13.1.4.1.1
Information about a particular physical network connection. Entries may be created and deleted in this table by the agent, if a physical topology discovery process is active. Rows in this table can only be created for MAC addresses that can validly be used in association with the type of interface concerned, as defined by table 8-2. The contents of this table is persistent across re-initializations or re-boots.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2RemEntry  

lldpV2RemTimeMark 1.3.111.2.802.1.1.13.1.4.1.1.1
A TimeFilter for this entry. See the TimeFilter textual convention in IETF RFC 4502 and http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt to see how TimeFilter works.
Status: current Access: not-accessible
OBJECT-TYPE    
  TimeFilter  

lldpV2RemLocalIfIndex 1.3.111.2.802.1.1.13.1.4.1.1.2
The interface index value used to identify the port associated with this entry. Its value is an index into the interfaces MIB The value of this object is used as an index to the lldpV2RemTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

lldpV2RemLocalDestMACAddress 1.3.111.2.802.1.1.13.1.4.1.1.3
The index value used to identify the destination MAC address associated with this entry. Its value identifies the row in the lldpV2DestAddressTable where the MAC address can be found. The value of this object is used as an index to the lldpV2RemTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2DestAddressTableIndex  

lldpV2RemIndex 1.3.111.2.802.1.1.13.1.4.1.1.4
This object represents an arbitrary local integer value used by this agent to identify a particular connection instance, unique only for the indicated remote system. An agent is encouraged to assign monotonically increasing index values to new entries, starting with one, after each reboot. It is considered unlikely that the lldpRemIndex can wrap between reboots.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..2147483647  

lldpV2RemChassisIdSubtype 1.3.111.2.802.1.1.13.1.4.1.1.5
The type of encoding used to identify the chassis associated with the remote system.
Status: current Access: read-only
OBJECT-TYPE    
  LldpV2ChassisIdSubtype  

lldpV2RemChassisId 1.3.111.2.802.1.1.13.1.4.1.1.6
The string value used to identify the chassis component associated with the remote system.
Status: current Access: read-only
OBJECT-TYPE    
  LldpV2ChassisId  

lldpV2RemPortIdSubtype 1.3.111.2.802.1.1.13.1.4.1.1.7
The type of port identifier encoding used in the associated 'lldpRemPortId' object.
Status: current Access: read-only
OBJECT-TYPE    
  LldpV2PortIdSubtype  

lldpV2RemPortId 1.3.111.2.802.1.1.13.1.4.1.1.8
The string value used to identify the port component associated with the remote system.
Status: current Access: read-only
OBJECT-TYPE    
  LldpV2PortId  

lldpV2RemPortDesc 1.3.111.2.802.1.1.13.1.4.1.1.9
The string value used to identify the description of the given port associated with the remote system.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

lldpV2RemSysName 1.3.111.2.802.1.1.13.1.4.1.1.10
The string value used to identify the system name of the remote system.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

lldpV2RemSysDesc 1.3.111.2.802.1.1.13.1.4.1.1.11
The string value used to identify the system description of the remote system.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

lldpV2RemSysCapSupported 1.3.111.2.802.1.1.13.1.4.1.1.12
The bitmap value used to identify which system capabilities are supported on the remote system.
Status: current Access: read-only
OBJECT-TYPE    
  LldpV2SystemCapabilitiesMap  

lldpV2RemSysCapEnabled 1.3.111.2.802.1.1.13.1.4.1.1.13
The bitmap value used to identify which system capabilities are enabled on the remote system.
Status: current Access: read-only
OBJECT-TYPE    
  LldpV2SystemCapabilitiesMap  

lldpV2RemRemoteChanges 1.3.111.2.802.1.1.13.1.4.1.1.14
Indicates that there are chances in the remote systems MIB, as determined by the variable remoteChanges.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

lldpV2RemTooManyNeighbors 1.3.111.2.802.1.1.13.1.4.1.1.15
Indicates that there are too many neighbors as determined by the variable tooManyNeighbors.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

lldpV2RemManAddrTable 1.3.111.2.802.1.1.13.1.4.2
This table contains one or more rows per management address information on the remote system learned on a particular port contained in the local chassis known to this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LldpV2RemManAddrEntry

lldpV2RemManAddrEntry 1.3.111.2.802.1.1.13.1.4.2.1
Management address information about a particular chassis component. There may be multiple management addresses configured on the remote system identified by a particular lldpRemIndex whose information is received on an interface of the local system and a given destination MAC address. Each management address should have distinct 'management address type' (lldpRemManAddrSubtype) and 'management address' (lldpRemManAddr.) Entries may be created and deleted in this table by the agent. Since a variable length octetstring is used as an index in a table, theaddress length is encoded as part of the OID (as per IETF RFC 2578).
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2RemManAddrEntry  

lldpV2RemManAddrSubtype 1.3.111.2.802.1.1.13.1.4.2.1.1
The type of management address identifier encoding used in the associated 'lldpRemManagmentAddr' object. It should be noted that only a subset of the possible address encodings enumerated in AddressFamilyNumbers are appropriate for use as a LLDP management address, either because some are just not apliccable or because the maximum size of a LldpV2ManAddress octet string would prevent the use of some address identifier encodings.
Status: current Access: not-accessible
OBJECT-TYPE    
  AddressFamilyNumbers  

lldpV2RemManAddr 1.3.111.2.802.1.1.13.1.4.2.1.2
The string value used to identify the management address component associated with the remote system. The purpose of this address is to contact the management entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2ManAddress  

lldpV2RemManAddrIfSubtype 1.3.111.2.802.1.1.13.1.4.2.1.3
The enumeration value that identifies the interface numbering method used for defining the interface number, associated with the remote system.
Status: current Access: read-only
OBJECT-TYPE    
  LldpV2ManAddrIfSubtype  

lldpV2RemManAddrIfId 1.3.111.2.802.1.1.13.1.4.2.1.4
The integer value used to identify the interface number regarding the management address component associated with the remote system. The value depends upon the value of the lldpV2RemManAddrIfSubtype for the table row.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

lldpV2RemManAddrOID 1.3.111.2.802.1.1.13.1.4.2.1.5
The OID value used to identify the type of hardware component or protocol entity associated with the management address advertised by the remote system agent.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

lldpV2RemUnknownTLVTable 1.3.111.2.802.1.1.13.1.4.3
This table contains information about an incoming TLV which is not recognized by the receiving LLDP agent. The TLV may be from a later version of the basic management set. This table should only contain TLVs that are found in a single LLDP frame. Entries in this table, associated with an MAC service access point (MSAP, the access point for MAC services provided to the LCC sublayer, defined in IEEE 100, which is also identified with a particular lldpRemLocalPortNum, lldpRemIndex pair) are overwritten with most recently received unrecognized TLV from the same MSAP, or they naturally age out when the rxInfoTTL timer (associated with the MSAP) expires.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LldpV2RemUnknownTLVEntry

lldpV2RemUnknownTLVEntry 1.3.111.2.802.1.1.13.1.4.3.1
Information about an unrecognized TLV received from a physical network connection. Entries may be created and deleted in this table by the agent, if a physical topology discovery process is active.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2RemUnknownTLVEntry  

lldpV2RemUnknownTLVType 1.3.111.2.802.1.1.13.1.4.3.1.1
This object represents the value extracted from the type field of the TLV.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 9..126  

lldpV2RemUnknownTLVInfo 1.3.111.2.802.1.1.13.1.4.3.1.2
This object represents the value extracted from the value field of the TLV.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..511)  

lldpV2RemOrgDefInfoTable 1.3.111.2.802.1.1.13.1.4.4
This table contains one or more rows per physical network connection which advertises the organizationally defined information. Note that this table contains one or more rows of organizationally defined information that is not recognized by the local agent. If the local system is capable of recognizing any organizationally defined information, appropriate extension MIBs from the organization should be used for information retrieval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LldpV2RemOrgDefInfoEntry

lldpV2RemOrgDefInfoEntry 1.3.111.2.802.1.1.13.1.4.4.1
Information about the unrecognized organizationally defined information advertised by the remote system. The lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex, lldpRemOrgDefInfoOUI, lldpRemOrgDefInfoSubtype, and lldpRemOrgDefInfoIndex are indexes to this table. If there is an lldpRemOrgDefInfoEntry associated with a particular remote system identified by the lldpRemLocalPortNum and lldpRemIndex, then there is an lldpRemEntry associated with the same instance (i.e, using same indexes.) When the lldpRemEntry for the same index is removed from the lldpRemTable, the associated lldpRemOrgDefInfoEntry is removed from the lldpRemOrgDefInfoTable. Entries may be created and deleted in this table by the agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  LldpV2RemOrgDefInfoEntry  

lldpV2RemOrgDefInfoOUI 1.3.111.2.802.1.1.13.1.4.4.1.1
The Organizationally Unique Identifier (OUI), as defined in IEEE Std 802, is a 24 bit (three octets) globally unique assigned number referenced by various standards, of the information received from the remote system.
Status: current Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(3)  

lldpV2RemOrgDefInfoSubtype 1.3.111.2.802.1.1.13.1.4.4.1.2
The integer value used to identify the subtype of the organizationally defined information received from the remote system. The subtype value is required to identify different instances of organizationally defined information that could not be retrieved without a unique identifier that indicates the particular type of information contained in the information string.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..255  

lldpV2RemOrgDefInfoIndex 1.3.111.2.802.1.1.13.1.4.4.1.3
This object represents an arbitrary local integer value used by this agent to identify a particular unrecognized organizationally defined information instance, unique only for the lldpRemOrgDefInfoOUI and lldpRemOrgDefInfoSubtype from the same remote system. An agent is encouraged to assign monotonically increasing index values to new entries, starting with one, after each reboot. It is considered unlikely that the lldpRemOrgDefInfoIndex can wrap between reboots.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..2147483647  

lldpV2RemOrgDefInfo 1.3.111.2.802.1.1.13.1.4.4.1.4
The string value used to identify the organizationally defined information of the remote system. The encoding for this object should be as defined for SnmpAdminString TC.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..507)  

lldpV2NotificationPrefix 1.3.111.2.802.1.1.13.0.0
OBJECT IDENTIFIER    

lldpV2RemTablesChange 1.3.111.2.802.1.1.13.0.0.1
A lldpV2RemTablesChange notification is sent when the value of lldpV2StatsRemTablesLastChangeTime changes. It can be utilized by an NMS to trigger LLDP remote systems table maintenance polls. Note that transmission of lldpV2RemTablesChange notifications are throttled by the agent, as specified by the 'lldpV2NotificationInterval' object.
Status: current Access: read-only
NOTIFICATION-TYPE    

lldpV2Compliances 1.3.111.2.802.1.1.13.2.1
OBJECT IDENTIFIER    

lldpV2Groups 1.3.111.2.802.1.1.13.2.2
OBJECT IDENTIFIER    

lldpV2TxRxCompliance 1.3.111.2.802.1.1.13.2.1.1
A compliance statement for all SNMP entities that implement the LLDP MIB as either a transmitter or a receiver of LLDPDUs. This version defines compliance requirements for V2 of the LLDP MIB module.
Status: current Access: read-only
MODULE-COMPLIANCE    

lldpV2TxCompliance 1.3.111.2.802.1.1.13.2.1.2
A compliance statement for SNMP entities that implement the LLDP MIB and have the capability of transmitting LLDP frames. This version defines compliance requirements for V2 of the LLDP MIB module.
Status: current Access: read-only
MODULE-COMPLIANCE    

lldpV2RxCompliance 1.3.111.2.802.1.1.13.2.1.3
The compliance statement for SNMP entities that implement the LLDP MIB. This version defines compliance requirements for V2 of the LLDP MIB module.
Status: current Access: read-only
MODULE-COMPLIANCE    

lldpV2ConfigGroup 1.3.111.2.802.1.1.13.2.2.1
The collection of objects which are used to configure the LLDP implementation behavior.
Status: current Access: read-only
OBJECT-GROUP    

lldpV2ConfigRxGroup 1.3.111.2.802.1.1.13.2.2.2
The collection of objects which are used to configure the LLDP implementation behavior.
Status: current Access: read-only
OBJECT-GROUP    

lldpV2ConfigTxGroup 1.3.111.2.802.1.1.13.2.2.3
The collection of objects which are used to configure the LLDP implementation behavior.
Status: current Access: read-only
OBJECT-GROUP    

lldpV2StatsRxGroup 1.3.111.2.802.1.1.13.2.2.4
The collection of objects which are used to represent LLDP reception statistics.
Status: current Access: read-only
OBJECT-GROUP    

lldpV2StatsTxGroup 1.3.111.2.802.1.1.13.2.2.5
The collection of objects which are used to represent LLDP transmission statistics.
Status: current Access: read-only
OBJECT-GROUP    

lldpV2LocSysGroup 1.3.111.2.802.1.1.13.2.2.6
The collection of objects which are used to represent LLDP Local System Information.
Status: current Access: read-only
OBJECT-GROUP    

lldpV2RemSysGroup 1.3.111.2.802.1.1.13.2.2.7
The collection of objects which are used to represent LLDP Remote Systems Information. The objects represent the information associated with the basic TLV set. Please note that even the agent doesn't implement some of the optional TLVs, it shall recognize all the optional TLV information that the remote system may advertise.
Status: current Access: read-only
OBJECT-GROUP    

lldpV2NotificationsGroup 1.3.111.2.802.1.1.13.2.2.8
The collection of notifications used to indicate LLDP MIB data consistency and general status information.
Status: current Access: read-only
NOTIFICATION-GROUP