LUMINOUS-TC-MIB

File: LUMINOUS-TC-MIB.mib (21563 bytes)

Imported modules

SNMPv2-TC	SNMPv2-SMI	RFC1213-MIB
RFC1155-SMI

Imported symbols

TEXTUAL-CONVENTION	MODULE-IDENTITY	OBJECT-TYPE
NOTIFICATION-TYPE	ObjectName	Integer32
Counter32	Unsigned32	DisplayString
enterprises

Defined Types

LumShelfType
Type of chassis.
TEXTUAL-CONVENTION
	INTEGER	mSeries(1), unused1(2), unused2(3), cSeries(4)

LumChassisPlane
Which plane in the chassis.
TEXTUAL-CONVENTION
	INTEGER	front(1), back(2)

LumSlotNum
Number of a slot within a chassis plane. Note that 0 is not a valid slot and means unknown.
TEXTUAL-CONVENTION
	Integer32	0..32

LumPortNum
Number of a port within a card.. Note that 0 is not a valid port and means unknown.
TEXTUAL-CONVENTION
	Integer32	0..32

LumSimpleIndex
Simple abstract integer index for a table.
TEXTUAL-CONVENTION
	Integer32	1..65535

LumPercent
A percentage value.
TEXTUAL-CONVENTION
	Unsigned32	0..100

LumRingDirection
Direction of a service of link from the ring point of view.
TEXTUAL-CONVENTION
	INTEGER	none(1), west(2), east(3)

LumAdminStatus
Administrative Status of an entity.
TEXTUAL-CONVENTION
	INTEGER	up(1), down(2)

LumOperStatus
Operational Status of an entity. This is based on IF-MIB ifOperStatus with the addition of misMatch.
TEXTUAL-CONVENTION
	INTEGER	up(1), down(2), testing(3), unknown(4), dormant(5), notPresent(6), lowerLayerDown(7), misMatch(8)

LumControl
Control of an entity.
TEXTUAL-CONVENTION
	INTEGER	unknown(1), disabled(2), enabled(3)

LumServiceMode
Service type for a port.
TEXTUAL-CONVENTION
	INTEGER	none(1), wire(2), routing(3), policyForwarding(4)

LumPortType
What type of entity is this port.
TEXTUAL-CONVENTION
	INTEGER	none(1), physical(2), subPortDemux(3)

LumPortCreateType
Was this port created explicitly or implicitly (e.g. chen channelizing a DS3, subports for DS1 are implicitly created.
TEXTUAL-CONVENTION
	INTEGER	implicit(1), explicit(2)

LumPortDemuxType
What type of entity is this demux port.
TEXTUAL-CONVENTION
	INTEGER	none(1), vlan(2), mplsTag(3), tdmChannel(4)

LumPortDemuxId
The substream identifier for this demux port.
TEXTUAL-CONVENTION
	Unsigned32	0..65535

LumConnectorType
Connector type for a physical port.
TEXTUAL-CONVENTION
	INTEGER	none(1), rj45(2), scFiber(3), miniCoax(4), db9(5), sjFiber(6), stFiber(7)

LumSignalState
State of a hardware signal.
TEXTUAL-CONVENTION
	INTEGER	idle(1), active(2)

LumName
Name of an entity. This should not include white space characters.
TEXTUAL-CONVENTION
	DisplayString	Size(1..40)

LumDescr
Description of an entity.
TEXTUAL-CONVENTION
	DisplayString	Size(1..80)

LumVersionString
Version of an entity.
TEXTUAL-CONVENTION
	DisplayString	Size(1..20)

LumSerialNumString
Serial number of an entity.
TEXTUAL-CONVENTION
	DisplayString	Size(1..21)

LumCleiString
CLEI code of an entity.
TEXTUAL-CONVENTION
	DisplayString	Size(1..17)

LumManufactureString
Manufacture date of an entity.
TEXTUAL-CONVENTION
	DisplayString	Size(1..20)

LumDateTimeString
Date and Time.
TEXTUAL-CONVENTION
	DisplayString	Size(24)

LumCardBaseType
The base type of a card.
TEXTUAL-CONVENTION
	INTEGER	none(1), sysCon(2), ring(3), t1(4), ether(5), alarm(6), upLink(7), ringIO(8), t1IO(9), etherIO(10), utility(11), oc12(12), oc12IO(13), gigE(14), gigEIO(15), oc12IOAlarm(16), etherFXIO(17), wdm(18), wdmIO(19), ringIOLR(21), ring2(22), ring2IO(23), ds3cc12(28), ds3cc12IO(29), ether24(32), ether24IO(33), asi(34), asiIOIn(35), asiIOOut(36), present(38)

LumCardType
The specific type of a card.
TEXTUAL-CONVENTION
	INTEGER	none(1), sysCon(2), ring(3), t1(4), ether(5), alarm(6), upLink(7), ringIO(8), t1IO(9), etherIO(10), utility(11), oc12(12), oc12IO(13), gigE(14), gigEIO(15), oc12IOAlarm(16), etherFXIO(17), wdm(18), wdmIO(19), sysconR(20), ringIOLR(21), ring2(22), ring2IO(23), wdmBand1(24), wdmBand2(25), wdmBand3(26), wdmBand4(27), ds3cc12(28), ds3cc12IO(29), t3cc12(30), e3cc12(31), ether24(32), ether24IO(33), asi(34), asiIOIn(35), asiIOOut(36), gigERouting(37), present(38), sysconU(39), newCardType(40)

LumCardAdminState
The admininstrative state of a card. This indicates the state transition desired by the management. The actual success of transition is shown in the card operationla state. active(2) - request to set a card in an active but not backed up state. standby(3)- request to set a card to a standby state. outOfService(4) - request to set a card to OutOfService state, where it should respond to the management requests but not support any traffic activity. shutDown(5)-request to shut the card down completely. Deprecated. reset(6) -request to reset the card. switchover(7)- request to replace this card, currently in lumCardOperState of active(7) with the card currently in lumCardOperState of standby(3) which slot is referenced with lumStandbySlot. On success, lumCardOperState of this card should transition to outOfService(4).
TEXTUAL-CONVENTION
	INTEGER	none(1), active(2), standby(3), outOfService(4), shutDown(5), reset(6), switchover(7)

LumCardOperState
The operational state of a card. The Operational State indicates the current state of the card. It can be either the result of some administrative management action or internal card activity. none(1) - indicates that there is no card in the slot active (2) - means working fine, but not backed up standby(3) - means backing up other active(2) cards in case of a failure or management switchover requests outOfService(4) - a state where the card should respond to the management requests but not support any traffic activity. failure(5) - cannot function properly but still can respond to management requests. down(6) - card in the slot can't even respond to the management request. present(7) - card is present in the slot and not yet identified. initializing(8)-card is present in the slot and is initializing.
TEXTUAL-CONVENTION
	INTEGER	none(1), active(2), standby(3), outOfService(4), failure(5), down(6), present(7), initializing(8)

LumCardFailureState
The failure state of a card. This is usually none(1), unless card operational state is equal to failure(5). Even if card operational state is equal to failure(5), still, this can be none(1), simply indicating that no information about this failure state is available. Otherwise criticalFault(2) indicates that the card cannot perform one of it's required functions properly. The management action is recommended (can be even reset or, if mulfunctioning, be replace) to correct the problem. Otherwise the problem will persist. minorFault(3) indicates that a fault has occured but does not persist. The action from the management may not beneeded. minorAlarm(4) indicates that no action is needed.
TEXTUAL-CONVENTION
	INTEGER	none(1), criticalFault(2), minorFault(3), minorAlarm(4)

LumOpticalWaveLength
The wavelength in nano-meters of an optical interface.
TEXTUAL-CONVENTION
	Integer32	1..65535

LumOpticalFiberType
The fiber type used by an optical interface.
TEXTUAL-CONVENTION
	INTEGER	unknown(1), singleMode(2), multiMode(3)

LumOpticalMaxLength
The maximum fiber length in meters of an optical interface.
TEXTUAL-CONVENTION
	Integer32	1..1000000

LumOpticalConnector
The connector type used by an optical interface.
TEXTUAL-CONVENTION
	INTEGER	unknown(1), sc(2), lc(3)

LumOpticalServiceSupport
The service types supported by an optical interface.
TEXTUAL-CONVENTION
	BITS	gigE1(0), gigE2(1), fiberChannel1(2), fiberChannel2(3), oc12(4), oc24(5), oc48(6), rpt(7), rptE2(8), oc3(9)

LumOpticalService
The service type active on an optical interface.
TEXTUAL-CONVENTION
	INTEGER	none(1), gigE1(2), gigE2(3), fiberChannel1(4), fiberChannel2(5), oc12(6), oc24(7), oc48(8), rpt(9), rptE2(10), oc3(11)

LumTdmType
The TDM port or connection type.
TEXTUAL-CONVENTION
	INTEGER	unknown(1), t1(2), e1(3), t3(4), e3(5)

LumImageState
The state of a program image in NVRAM.
TEXTUAL-CONVENTION
	INTEGER	empty(1), trial(2), tried(3), accepted(4), unknown(5)

LumAlarmSeverity
The severity of an alarm of group of alarms.
TEXTUAL-CONVENTION
	INTEGER	undefined(1), critical(2), major(3), minor(4), notAlarmed(5), notReported(6)

LumResetCmd
Reset command for an entity.
TEXTUAL-CONVENTION
	INTEGER	none(1), reset(2)

Defined Values

luminous		1.3.6.1.4.1.4614
OBJECT IDENTIFIER

lumADM		1.3.6.1.4.1.4614.1
OBJECT IDENTIFIER

lumTcMIB		1.3.6.1.4.1.4614.1.9
The Luminous TC MIB contains textual conventions for use in Luminous Networks MIBs.
MODULE-IDENTITY

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor