MDM-MIB

File: MDM-MIB.mib (170132 bytes)

Imported modules

Imported symbols

enterprises	experimental	IpAddress
TimeTicks	Gauge	Counter
DisplayString	OBJECT-TYPE

Defined Types

MdmIDEntry
SEQUENCE
	mdmIDIndex	INTEGER
	mdmIDModel	INTEGER
	mdmIDCountry	INTEGER
	mdmIDHardwareSerNum	DisplayString
	mdmIDHardwareRev	DisplayString
	mdmIDSupervisorSwRev	DisplayString
	mdmIDDataPumpSwRev	DisplayString
	mdmIDIoProcessorSwRev	DisplayString
	mdmIDSupervisorDate	DisplayString

MdmLiEntry
SEQUENCE
	mdmLiIndex	INTEGER
	mdmLiDialPause	INTEGER
	mdmLiCarrierRecDelay	INTEGER
	mdmLiCarrierLoss	INTEGER
	mdmLiToneDialTiming	INTEGER
	mdmLiDteRxDataDelay	INTEGER
	mdmLiTransmiter	INTEGER
	mdmLiDialMode	INTEGER
	mdmLiGuardTone	INTEGER
	mdmLiLeasedLine	INTEGER
	mdmLiLeasedLineRestDelay	INTEGER
	mdmLiPulseMakeBreak	INTEGER
	mdmLiAnswerTone	INTEGER
	mdmLiRemoteEscGuardTime	INTEGER
	mdmLiRemoteEscChar	INTEGER
	mdmLiRemAccessLimit	INTEGER
	mdmLiRemPassword0	DisplayString
	mdmLiRemPassword1	DisplayString
	mdmLiTransmitLevel	INTEGER
	mdmLiSrc	INTEGER

MdmDcEntry
SEQUENCE
	mdmDcIndex	INTEGER
	mdmDcDataCompression	INTEGER

MdmTfEntry
SEQUENCE
	mdmTfIndex	INTEGER
	mdmTfTest	INTEGER
	mdmTfTestTime	INTEGER
	mdmTfV54	INTEGER
	mdmTfV54Errors	INTEGER
	mdmTfATG	OCTET STRING
	mdmTfDialInToneTest	INTEGER
	mdmTfToneTestCallRef	OCTET STRING

MdmTfToneEntry
SEQUENCE
	mdmTfToneIndex	INTEGER
	mdmTfTxFreq	INTEGER
	mdmTfTxAmpl	INTEGER
	mdmTfRxFreq	INTEGER
	mdmTfRxAmpl	INTEGER

MdmTfRspndrEntry
SEQUENCE
	mdmTfRspndrIndex	INTEGER
	mdmTf404FarNearLvl	INTEGER
	mdmTf404NearFarLvl	INTEGER
	mdmTf1004FarNearLvl	INTEGER
	mdmTf1004NearFarLvl	INTEGER
	mdmTf2804FarNearLvl	INTEGER
	mdmTf2804NearFarLvl	INTEGER
	mdmTfCmsgFarNearLvl	INTEGER
	mdmTfCmsgNearFarLvl	INTEGER
	mdmTfCnotchFarNearLvl	INTEGER
	mdmTfCnotchNearFarLvl	INTEGER
	mdmtTfSigNoiseFarNearLvl	INTEGER
	mdmtTfSigNoiseNearFarLvl	INTEGER
	mdmTf404FarNearSts	INTEGER
	mdmTf404NearFarSts	INTEGER
	mdmTf1004FarNearSts	INTEGER
	mdmTf1004NearFarSts	INTEGER
	mdmTf2804FarNearSts	INTEGER
	mdmTf2804NearFarSts	INTEGER
	mdmTfCmsgFarNearSts	INTEGER
	mdmTfCmsgNearFarSts	INTEGER
	mdmTfCnotchFarNearSts	INTEGER
	mdmTfCnotchNearFarSts	INTEGER
	mdmTfSigNoiseFarNearSts	INTEGER
	mdmTfSigNoiseNearFarSts	INTEGER
	mdmTf0dB1004FarNearLvl	INTEGER
	mdmTf0dB1004NearFarLvl	INTEGER
	mdmTf0dB1004FarNearSts	INTEGER
	mdmTf0dB1004NearFarSts	INTEGER

MdmDiEntry
SEQUENCE
	mdmDiIndex	INTEGER
	mdmDiEscCodeGuardTime	INTEGER
	mdmDiLocalEscChar	INTEGER
	mdmDiCarriageRetChar	INTEGER
	mdmDiLineFeedChar	INTEGER
	mdmDiBackspaceChar	INTEGER
	mdmDiDelAsBackspace	INTEGER
	mdmDiResetOnDtrEna	INTEGER
	mdmDiResultCodePauseDis	INTEGER
	mdmDiInterbridgeEna	INTEGER
	mdmDiBreakLen	INTEGER
	mdmDiXonChar	INTEGER
	mdmDiXoffChar	INTEGER
	mdmDiDsrPulseTime	INTEGER
	mdmDiRtsCtsDelay	INTEGER
	mdmDiHiSpeedResCodeEna	INTEGER
	mdmDiCmdLocalEchoEna	INTEGER
	mdmDiDataModeEchoEna	INTEGER
	mdmDiDteDataRateMode	INTEGER
	mdmDiCdOverride	INTEGER
	mdmDiDtrOverride	INTEGER
	mdmDiDsrOverride	INTEGER
	mdmDiEiaLineStatus	INTEGER
	mdmDiTransmitFlowCntl	INTEGER
	mdmDiSoftwareRxFlowCntl	INTEGER
	mdmDiHardwareRxFlowCntl	INTEGER
	mdmDiBreakHandling	INTEGER
	mdmDiDteNvramLock	INTEGER
	mdmDiSerialFormat	INTEGER
	mdmDiDefaultDteDataRate	INTEGER
	mdmDiRemAccessMsg	INTEGER
	mdmDiV25DteDataRate	INTEGER
	mdmDiSrc	INTEGER
	mdmDiSlot	INTEGER
	mdmDiBusyClock	INTEGER
	mdmDiAtString	DisplayString
	mdmDiDtrRecognitionTime	INTEGER

MdmScEntry
SEQUENCE
	mdmScIndex	INTEGER
	mdmScLinkRateSelect	INTEGER
	mdmScNonArqBufSize	INTEGER
	mdmScNonMnpDataCapture	INTEGER
	mdmScSyncTimingSource	INTEGER
	mdmScHstMod	INTEGER
	mdmScHiFreqEq	INTEGER
	mdmScBackChanRate	INTEGER
	mdmScV21Mod	INTEGER
	mdmScV32UnencodedMod	INTEGER
	mdmScV32Mod	INTEGER
	mdmScBell208	INTEGER
	mdmScV32Bis	INTEGER
	mdmScV32BisEnhance	INTEGER
	mdmScV32QuickRetrain	INTEGER
	mdmScV23	INTEGER
	mdmScHiSpeedModulation	INTEGER
	mdmScFallback	INTEGER
	mdmScV32TerboModeEnable	INTEGER
	mdmScV34ModeEnable	INTEGER
	mdmScVFCSymRate2400	INTEGER
	mdmScVFCSymRate2743	INTEGER
	mdmScVFCSymRate2800	INTEGER
	mdmScVFCSymRate3000	INTEGER
	mdmScVFCSymRate3200	INTEGER
	mdmScVFCSymRate3429	INTEGER
	mdmScVFC8S2DMapping	INTEGER
	mdmScVFC16S4DMapping	INTEGER
	mdmScVFC32S2DMapping	INTEGER
	mdmScVFC64S4DMapping	INTEGER
	mdmScVFCNonLinearCoding	INTEGER
	mdmScVFCTxLevelDeviation	INTEGER
	mdmScVFCPreEmphasis	INTEGER
	mdmScVFCPreCoding	INTEGER
	mdmScVFCShaping	INTEGER
	mdmScVFCModeEnable	INTEGER
	mdmScV8	INTEGER
	mdmSCV8CallIndicator	INTEGER
	mdmScV34pModeEnable	INTEGER
	mdmSc300	INTEGER
	mdmSc1200	INTEGER
	mdmSc2400	INTEGER
	mdmScHighSpeed	INTEGER
	mdmScSelectiveReject	INTEGER
	mdmScPhExclusionDel	INTEGER
	mdmScLinkRateAmpU	INTEGER
	mdmScLowerSpeedMin	INTEGER
	mdmScLowerSpeedMax	INTEGER
	mdmScX2Client	INTEGER
	mdmScX2Server	INTEGER
	mdmScX2Symmetric	INTEGER
	mdmScX2HighPowerConst	INTEGER
	mdmScPiafs	INTEGER
	mdmScPiafsV42bis	INTEGER
	mdmScTxPwrLvl	INTEGER
	mdmScTxPwrLvlApplied	INTEGER
	mdmScX2Version2	INTEGER
	mdmScV34Fallback	INTEGER
	mdmScV90Analogue	INTEGER
	mdmScV90Digital	INTEGER
	mdmScV90AllDigital	INTEGER

MdmCcEntry
SEQUENCE
	mdmCcIndex	INTEGER
	mdmCcDialDelay	INTEGER
	mdmCcWaitForCarrier	INTEGER
	mdmCcInactivityTimer	INTEGER
	mdmCcAutoDialOnDtrEna	INTEGER
	mdmCcAutoDialOnPwrUpEna	INTEGER
	mdmCcGhostPortLockEna	INTEGER
	mdmCcQuietResultCodes	INTEGER
	mdmCcResponseMode	INTEGER
	mdmCcResultCodeOptions	INTEGER
	mdmCcArqResultCodeMode	INTEGER
	mdmCcEscCodeRsp	INTEGER
	mdmCcAtRecognition	INTEGER
	mdmCcMgmtSysMsgDis	INTEGER
	mdmCcV32ToneDuration	INTEGER
	mdmCcAutoAnswer	INTEGER
	mdmCcAnswerInOrigMode	INTEGER
	mdmCcArqBufWait	INTEGER
	mdmCcPhoneString0	DisplayString
	mdmCcPhoneString1	DisplayString
	mdmCcPhoneString2	DisplayString
	mdmCcPhoneString3	DisplayString
	mdmCcErrorCntlMode	INTEGER
	mdmCcMiMic	INTEGER
	mdmCcMnpWith1200	INTEGER
	mdmCcMnpWith2400	INTEGER
	mdmCcMnpWithV32	INTEGER
	mdmCcMnpTimeout	INTEGER
	mdmCcV21V23FallBackTimer	INTEGER
	mdmCcAddnlAnswToneDur	INTEGER
	mdmCcBillingDelayPeriod	INTEGER
	mdmCcCarrierAccessCode1	DisplayString
	mdmCcCarrierAccessCode2	DisplayString
	mdmCcCarrierAccessCode3	DisplayString
	mdmCcCallingInitStr1	DisplayString
	mdmCcCallingInitStr2	DisplayString
	mdmCcCallingInitStr3	DisplayString
	mdmCcCallingInitStr4	DisplayString
	mdmCcDataFaxMode	INTEGER
	mdmCcT1CallSetupProc	INTEGER
	mdmCcT1DialToneType	INTEGER
	mdmCcT1KpStMfTones	INTEGER
	mdmCcT1CallInitStrUse	INTEGER
	mdmCcT1CallInitStrBase	INTEGER
	mdmCcIntBlackListDis	INTEGER
	mdmCcOffHookRestrict	INTEGER
	mdmCcT1DialInAniDig	INTEGER
	mdmCcT1DialInDnisDig	INTEGER
	mdmCcNoPbNoConnEna	INTEGER
	mdmCcIdleDiscPatt	INTEGER
	mdmCcMnp10	INTEGER
	mdmCcMnp10Ec	INTEGER
	mdmCcAtzPbHandling	INTEGER
	mdmCcDefltPRISlot	INTEGER
	mdmCcExtDTMFToneSupport	INTEGER
	mdmCcDataOverVoice	INTEGER
	mdmCc2100AnswerTone	INTEGER
	mdmCcEnableV120v42Bis	INTEGER
	mdmCcHdlcLicIe	INTEGER
	mdmCcDtmfTerminationTone	INTEGER
	mdmCcAfaxMaxRateSrvOpt20	INTEGER
	mdmCcAfaxMaxRateSrvOpt21	INTEGER

MdmEcEntry
SEQUENCE
	mdmEcIndex	INTEGER
	mdmEcMnp3Dis	INTEGER
	mdmEcMnp4Dis	INTEGER
	mdmEcMnpUnusual	INTEGER
	mdmEcV42MnpHandshake	INTEGER

MdmCsEntry
SEQUENCE
	mdmCsIndex	INTEGER
	mdmCsStatus	INTEGER
	mdmCsLastNumberDialedOut	DisplayString
	mdmCsLastNumberDialedIn	DisplayString
	mdmCsLastCallingPartyNum	DisplayString
	mdmCsOriginateAnswer	INTEGER
	mdmCsRings	INTEGER
	mdmCsDisconnectReason	INTEGER
	mdmCsConnectFailReason	INTEGER
	mdmCsInitialTxLinkRate	INTEGER
	mdmCsInitialRxLinkRate	INTEGER
	mdmCsFinalTxLinkRate	INTEGER
	mdmCsFinalRxLinkRate	INTEGER
	mdmCsModulationType	INTEGER
	mdmCsSyncAsyncModeUsed	INTEGER
	mdmCsErrorControlType	INTEGER
	mdmCsCompressionType	INTEGER
	mdmCsEqualizationType	INTEGER
	mdmCsFallbackEnabled	INTEGER
	mdmCsCharsSent	INTEGER
	mdmCsCharsReceived	INTEGER
	mdmCsOctetsSent	INTEGER
	mdmCsOctetsReceived	INTEGER
	mdmCsBlocksSent	INTEGER
	mdmCsBlocksReceived	INTEGER
	mdmCsBlocksResent	INTEGER
	mdmCsRetrainsRequested	INTEGER
	mdmCsRetrainsGranted	INTEGER
	mdmCsLineReversalQty	INTEGER
	mdmCsCharsLost	INTEGER
	mdmCsBackChannelRate	INTEGER
	mdmCsBlerQty	INTEGER
	mdmCsLinkTimeoutQty	INTEGER
	mdmCsFallbackQty	INTEGER
	mdmCsUpshiftQty	INTEGER
	mdmCsLinkNakQty	INTEGER
	mdmCsGainHitCount	INTEGER
	mdmCsSecurityUserName	DisplayString
	mdmCsCallDuration	DisplayString
	mdmCsCallRefNum	INTEGER
	mdmCsPriCardSlot	INTEGER
	mdmCsTDMTimeSlot	INTEGER
	mdmCsPriCardSpanLine	INTEGER
	mdmCsBChannelUsed	INTEGER
	mdmCsQCarrFreqTx	INTEGER
	mdmCsQCarrFreqRx	INTEGER
	mdmCsQSymRateTx	INTEGER
	mdmCsQSymRateRx	INTEGER
	mdmCsQTrellisTx	INTEGER
	mdmCsQTrellisRx	INTEGER
	mdmCsQNonLinCdTx	INTEGER
	mdmCsQNonLinCdRx	INTEGER
	mdmCsQPrecodingTx	INTEGER
	mdmCsQPrecodingRx	INTEGER
	mdmCsQShapingTx	INTEGER
	mdmCsQShapingRx	INTEGER
	mdmCsQPreemphTx	INTEGER
	mdmCsQPreemphRx	INTEGER
	mdmCsQRxLevel	INTEGER
	mdmCsQTxLevel	INTEGER
	mdmCsQSNR	INTEGER
	mdmCsQNearEcho	INTEGER
	mdmCsQFarEcho	INTEGER
	mdmCsQRndTripDly	INTEGER
	mdmCsQPacketSizeCurr	INTEGER
	mdmCsQPacketSizeLow	INTEGER
	mdmCsQPacketSizeHigh	INTEGER
	mdmCsQCellTxLevelCurr	INTEGER
	mdmCsQCellTxLevelLow	INTEGER
	mdmCsQCellTxLevelHigh	INTEGER
	mdmCsQSNRLevelCurr	INTEGER
	mdmCsQSNRLevelLow	INTEGER
	mdmCsQSNRLevelHigh	INTEGER
	mdmCsQCellularProt	INTEGER
	mdmCsFreqProbeData	OCTET STRING
	mdmCsLevelProbeData	OCTET STRING
	mdmCsQTimingOffset	INTEGER
	mdmCsQCarrierOffset	INTEGER
	mdmCsQCoding	INTEGER
	mdmCsTrainingInfo	OCTET STRING
	mdmCsX2signature	OCTET STRING
	mdmCsX2Status	INTEGER
	mdmCsCallType	INTEGER
	mdmCsCallStartTime	INTEGER
	mdmCsCallEndTime	INTEGER
	mdmCsDigitalPadAttenuated	INTEGER
	mdmCsInitModulationType	INTEGER
	mdmCsRxMinSpeed	INTEGER
	mdmCsRxMaxSpeed	INTEGER
	mdmCsTxMinSpeed	INTEGER
	mdmCsTxMaxSpeed	INTEGER
	mdmCsCollectedDTMFDigits	OCTET STRING

MdmEvEntry
SEQUENCE
	mdmEvIndex	INTEGER
	mdmEvWatchdogTimouts	Counter
	mdmEvDteIdleTimouts	Counter
	mdmEvInConnectEstabs	Counter
	mdmEvOutConnectEstabs	Counter
	mdmEvInConnectTerms	Counter
	mdmEvOutConnectTerms	Counter
	mdmEvConnectAttemptFails	Counter
	mdmEvConnectTimouts	Counter
	mdmEvMgmtBusFailures	Counter
	mdmEvResetByDtes	Counter
	mdmEvDtrFalses	Counter
	mdmEvDtrTrues	Counter
	mdmEvNoTones	Counter
	mdmEvNoLoops	Counter
	mdmEvBlers	Counter
	mdmEvFallBacks	Counter
	mdmEvInConnectTime	Counter
	mdmEvInTotalBytesRx	Counter
	mdmEvInTotalBytesTx	Counter
	mdmEvOutConnectTime	Counter
	mdmEvOutTotalBytesRx	Counter
	mdmEvOutTotalBytesTx	Counter
	mdmEvInConnAttemptFails	Counter
	mdmEvOutConnAttemptFails	Counter

MdmEtEntry
SEQUENCE
	mdmEtIndex	INTEGER
	mdmEtDteIdleThresh	INTEGER
	mdmEtDtrFalseThresh	INTEGER
	mdmEtDtrTrueThresh	INTEGER
	mdmEtConnTimeLimit	INTEGER
	mdmEtBlerThresh	INTEGER
	mdmEtFallbackThresh	INTEGER

MdmCdEntry
SEQUENCE
	mdmCdIndex	INTEGER
	mdmCdMgtStationId	OCTET STRING
	mdmCdReqId	INTEGER
	mdmCdFunction	INTEGER
	mdmCdForce	INTEGER
	mdmCdParam	OCTET STRING
	mdmCdResult	INTEGER
	mdmCdCode	INTEGER

MdmTeEntry
SEQUENCE
	mdmTeIndex	INTEGER
	mdmTeInConnEstablished	INTEGER
	mdmTeOutConnEstablished	INTEGER
	mdmTeInConnTerminated	INTEGER
	mdmTeOutConnTerminated	INTEGER
	mdmTeConnAttemptFailure	INTEGER
	mdmTeConnLimitExpired	INTEGER
	mdmTeDteXmitDataIdle	INTEGER
	mdmTeDtrTrue	INTEGER
	mdmTeDtrFalse	INTEGER
	mdmTeBlerCountAtThresh	INTEGER
	mdmTeFallbkCountAtThresh	INTEGER
	mdmTeNoDialTone	INTEGER
	mdmTeNoLoopCurrent	INTEGER
	mdmTeResetByDTE	INTEGER
	mdmTeDialOutCallDur	INTEGER
	mdmTeDialInCallDur	INTEGER
	mdmTePbActive	INTEGER
	mdmTePbLost	INTEGER
	mdmTeDteRingNoAns	INTEGER
	mdmTePbClockLossEvent	INTEGER
	mdmTePbClockRestoreEvent	INTEGER
	mdmTeInConnAttemptFail	INTEGER
	mdmTeOutConnAttemptFail	INTEGER
	mdmTe105ResponderTest	INTEGER

MdmLsTableEntry
SEQUENCE
	mdmLsIndex	INTEGER
	mdmLsSecurityEnable	INTEGER
	mdmLsFallbackPromptEnable	INTEGER
	mdmLsForcePromptEnable	INTEGER
	mdmLsLocAccPasswdEnable	INTEGER
	mdmLsDialBackEnable	INTEGER
	mdmLsAutoPassPasswd	DisplayString
	mdmLsLocalAccessPasswd	DisplayString
	mdmLsAccountPasswd	DisplayString

MdmHsEntry
SEQUENCE
	mdmHsIndex	INTEGER
	mdmHsDialInEnable	INTEGER
	mdmHsDialOutEnable	INTEGER
	mdmHsDtrDcdDelay	INTEGER
	mdmHsDtrDsrDelay	INTEGER

MdmArEntry
SEQUENCE
	mdmArIndex	INTEGER
	mdmArIncomConnectEstab	OCTET STRING
	mdmArOutgoConnectEstab	OCTET STRING
	mdmArIncomConnectTerm	OCTET STRING
	mdmArOutgoConnectTerm	OCTET STRING
	mdmArConnectAttemptFail	OCTET STRING
	mdmArConnectTimeExpire	OCTET STRING
	mdmArResetByDte	OCTET STRING
	mdmArDteXmitIdle	OCTET STRING
	mdmArBlersAtThresh	OCTET STRING
	mdmArFbacksAtThresh	OCTET STRING
	mdmArDialOutLoginFail	OCTET STRING
	mdmArDialOutRestrNum	OCTET STRING
	mdmArDialInLoginFail	OCTET STRING
	mdmArDialBackRestrNum	OCTET STRING
	mdmArDialBackRestModem	OCTET STRING
	mdmArLoginAttemptsExceed	OCTET STRING
	mdmArUserBlacklisted	OCTET STRING
	mdmArAttmpLoginByBlistUsr	OCTET STRING
	mdmArRspAttemptLimExceed	OCTET STRING
	mdmArWatchdog	OCTET STRING
	mdmArMgtBusFailure	OCTET STRING
	mdmArDtrTrue	OCTET STRING
	mdmArDtrFalse	OCTET STRING
	mdmArMdmRingNoAnswer	OCTET STRING
	mdmArDteRingNoAnswer	OCTET STRING
	mdmArNoDialTone	OCTET STRING
	mdmArNoLoopCurrent	OCTET STRING
	mdmArTimer1	OCTET STRING
	mdmArTimer2	OCTET STRING
	mdmArTimer3	OCTET STRING
	mdmArTimer4	OCTET STRING
	mdmArPacketBusActive	OCTET STRING
	mdmArPacketBusLost	OCTET STRING

MdmCeEntry
SEQUENCE
	mdmCeIndex	INTEGER
	mdmCeMnp10Dis	INTEGER
	mdmCeMnpxDis	INTEGER
	mdmCeComp	INTEGER
	mdmCeOperDis	INTEGER
	mdmCeLinkSpeed	INTEGER
	mdmCeShortFormRules	INTEGER
	mdmCeDceBitraLim	INTEGER
	mdmCeDceTxLev	INTEGER
	mdmCeV42EtcDis	INTEGER
	mdmCeV42CellSite	INTEGER
	mdmCeV42EtcCallToneDis	INTEGER
	mdmCeV42EtcTxLevConDis	INTEGER
	mdmCeDceStartRate	INTEGER
	mdmCeV42DceTxDemDis	INTEGER
	mdmCeMnp10FallbackDis	INTEGER
	mdmCeMnp10FallforDis	INTEGER
	mdmCeDbNoEtcDis	INTEGER
	mdmCeMnpxDetPhEna	INTEGER

MdmStsEntry
SEQUENCE
	mdmStsIndex	INTEGER
	mdmStsPbClock	INTEGER

MdmMaEntry
SEQUENCE
	mdmMaIndex	INTEGER
	mdmMaChangeIndicator	INTEGER
	mdmMaChannelConfig	INTEGER

Defined Values

usr		1.3.6.1.4.1.429
OBJECT IDENTIFIER

nas		1.3.6.1.4.1.429.1
OBJECT IDENTIFIER

mdm		1.3.6.1.4.1.429.1.6
OBJECT IDENTIFIER

mdmID		1.3.6.1.4.1.429.1.6.1
OBJECT IDENTIFIER

mdmIDTable		1.3.6.1.4.1.429.1.6.1.1
A list of modem ID entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmIDEntry

mdmIDEntry		1.3.6.1.4.1.429.1.6.1.1.1
An Identification table entry, containing objects which define the identity and capabilities of a modem.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmIDEntry

mdmIDIndex		1.3.6.1.4.1.429.1.6.1.1.1.1
A unique value for each modem configured in the system based on the values in the entity table in the USR extensions to the chassis mib.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmIDModel		1.3.6.1.4.1.429.1.6.1.1.1.2
Defines the model (ie. V.23, HST, etc.) of the modem represented by this row in the table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), v32bisDualStandard(2), hst(3), v32bis(4), v32terboDualStandard(11), v32terbo(12), v32terboFax(13), v34DualStandard(14), v34(15), v34Fax(16), v34FaxISDN(30), x2(31), hdm24Channel(32), hdm30Channel(33), cdma(39)

mdmIDCountry		1.3.6.1.4.1.429.1.6.1.1.1.3
This object identifies the country or countries that this modem is designed for use in.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), northamerica(2), japan(3), finland(4), sweden(5), uk(6), norway(7), switzerland(8), netherlands(9), southAfrica(10), italy(11), newZealand(12), czech(13), belgium(14), denmark(15), australia(16), france(17), germany(18), ccitt(19), austria(20), ireland(21), spain(22), portugal(23), malaysia(24)

mdmIDHardwareSerNum		1.3.6.1.4.1.429.1.6.1.1.1.4
The modem's hardware serial number as stored in EEPROM.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..16)

mdmIDHardwareRev		1.3.6.1.4.1.429.1.6.1.1.1.5
The hardware revision of the modem as stored in the modem's EEPROM.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..11)

mdmIDSupervisorSwRev		1.3.6.1.4.1.429.1.6.1.1.1.6
The revision of the software being executed by the modem's supervisor processor.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..11)

mdmIDDataPumpSwRev		1.3.6.1.4.1.429.1.6.1.1.1.7
The revision of software being executed by the modem's data pump processor.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..11)

mdmIDIoProcessorSwRev		1.3.6.1.4.1.429.1.6.1.1.1.8
The revison of software being executed by the modem's IO Control Processor.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..11)

mdmIDSupervisorDate		1.3.6.1.4.1.429.1.6.1.1.1.9
The supervisor build date.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..8)

mdmLi		1.3.6.1.4.1.429.1.6.2
OBJECT IDENTIFIER

mdmLiTable		1.3.6.1.4.1.429.1.6.2.1
A list of configurable Line Interface objects for a modem. The number of table entries is given by modemNumber.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmLiEntry

mdmLiEntry		1.3.6.1.4.1.429.1.6.2.1.1
Objects which define the line interface characteristics for a particualar modem.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmLiEntry

mdmLiIndex		1.3.6.1.4.1.429.1.6.2.1.1.1
Index into the Line Interface table. This index is the value from the chassis mib entity relation table that is applicable for a particular modem.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmLiDialPause		1.3.6.1.4.1.429.1.6.2.1.1.2
Duration in seconds for the pause(') option in the dial command and the pause between command re-executions(> and A>) Default = 2. Equates to the modem's S8 register.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmLiCarrierRecDelay		1.3.6.1.4.1.429.1.6.2.1.1.3
Duration in 10ths of a second that the remote modem's carrier signal must be present before recognition. Ignored at speeds above 2400. Equates to the modem's S9 register. Default=6.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmLiCarrierLoss		1.3.6.1.4.1.429.1.6.2.1.1.4
Duration in 10ths of a second the modem waits after loss of carrier before hanging up. This allows the modem to distinguish between a momentary lapse in line quality and a true disconnect. When equal to 255 the modem will remain off hook until DTR drops or an ATH command is recieved. Equates to the modem's S10 register. Default=7.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmLiToneDialTiming		1.3.6.1.4.1.429.1.6.2.1.1.5
Duration and spacing in milliseconds of dialed Touch Tones. Equates to the modem's S10 register. Default=70.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmLiDteRxDataDelay		1.3.6.1.4.1.429.1.6.2.1.1.6
Duration in 10ths of a second that the modem inserts a RX transmission delay between CD and the first recieved character. Intended for custom applications and not recomended for general usage. Equates to the modem's S35 register. Default=0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmLiTransmiter		1.3.6.1.4.1.429.1.6.2.1.1.7
Enables the modem to transmit data. Corresponds to the modem 'C' register. Default=2.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmLiDialMode		1.3.6.1.4.1.429.1.6.2.1.1.8
Determines whether the modem uses pulse or tone for dialing when initiating outgoing calls. Equates to the P and T registers in the modem. Default=0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	pulse(1), tone(2)

mdmLiGuardTone		1.3.6.1.4.1.429.1.6.2.1.1.9
This object is required for modems answering calls that originate from sites outside of North America. The modem's must be operating in either 1200 or 2400 bps and be using the V.32 answer sequence. This object defines what guard tone is used for answering calls. This object equates to the &G register in US Robotics modems. Default=none.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), european550(2), uk1800(3)

mdmLiLeasedLine		1.3.6.1.4.1.429.1.6.2.1.1.10
Enables modem to operate in leased line mode. When enabled the local an remote modems make a continuous connection without dialing. Should the connection be broken the modem's will attempt to automaticly reestablish it(see mdmCcLeasedLineRest). Equates to the modem's &L register Default = disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2), cellularHSTMode(3)

mdmLiLeasedLineRestDelay		1.3.6.1.4.1.429.1.6.2.1.1.11
Sets the duration, in seconds, of the delay between when the modem senses loss of carrier and when it attempts to reestablish a leased line connection. The default setting of 15 should be appropriate for most installations.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmLiPulseMakeBreak		1.3.6.1.4.1.429.1.6.2.1.1.12
Determines the ratio of off hook to on hook interval for Pulse dialing. Equates to the modem's &P register. Default=North America.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	northAmerica(1), britishCommonwealth(2)

mdmLiAnswerTone		1.3.6.1.4.1.429.1.6.2.1.1.13
Disables the 2100 Hz Answer tone allowing V.42 modems to connect more quickly and/or eliminating problems with older 2400-bps modems that do not recognise this tone. Equates to the modem's S27.3 register. Default=Enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmLiRemoteEscGuardTime		1.3.6.1.4.1.429.1.6.2.1.1.14
Sets the duration in 20 millisecond increments of the guard time that the modem requires preceding and following the remote escape sequence. The default is 200 or 4 seconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmLiRemoteEscChar		1.3.6.1.4.1.429.1.6.2.1.1.15
Specifies the decimal value of the character used in the remote access escape code for entering online command mode on this modem from the remote site. Default = 126(~).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmLiRemAccessLimit		1.3.6.1.4.1.429.1.6.2.1.1.16
Determines the number of attempts to enter remote online command mode that are allowed for any one connection. The default is 0 which disables the remote access functon.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmLiRemPassword0		1.3.6.1.4.1.429.1.6.2.1.1.17
The password that allows a dial-in user to gain view only access to this modems parameters. A maximum of 8 characters is allowed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..8)

mdmLiRemPassword1		1.3.6.1.4.1.429.1.6.2.1.1.18
The password used by a dial-in user to gain read-write access to this modems configuration. Maximum length is 8 characters.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..8)

mdmLiTransmitLevel		1.3.6.1.4.1.429.1.6.2.1.1.19
Specifies the signal level of the modem transmitter in negative db.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..20

mdmLiSrc		1.3.6.1.4.1.429.1.6.2.1.1.20
Specifies either NIC or TDM as the source for the line interface.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	nic(1), t1Tdm(2), priTdm(3)

mdmDc		1.3.6.1.4.1.429.1.6.3
OBJECT IDENTIFIER

mdmDcTable		1.3.6.1.4.1.429.1.6.3.1
A table of configurable objects that define the operation of Data Compression in the modem.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmDcEntry

mdmDcEntry		1.3.6.1.4.1.429.1.6.3.1.1
Objects which define Data Compression operation for a modem.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmDcEntry

mdmDcIndex		1.3.6.1.4.1.429.1.6.3.1.1.1
The index into the Data Compression table. This object contains the unique value for this modem as defined in the chassis mib entity relation table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmDcDataCompression		1.3.6.1.4.1.429.1.6.3.1.1.2
Determines when and how data compression is enabled. Corresponds to the &K register in USR modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), autoEnable(2), enable(3), mnpWoCompression(4)

mdmTf		1.3.6.1.4.1.429.1.6.4
OBJECT IDENTIFIER

mdmTfTable		1.3.6.1.4.1.429.1.6.4.1
Table of test functions for modems. There is a table entry for each modem the quantity of which is specified by modemNumber.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmTfEntry

mdmTfEntry		1.3.6.1.4.1.429.1.6.4.1.1
Objects used to request thet the modem perform certain diagnostic tests.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmTfEntry

mdmTfIndex		1.3.6.1.4.1.429.1.6.4.1.1.1
A unique value used to identify this modem the value of which is determined by the entity table in the chassis mib and used as a method to index into the test function table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTfTest		1.3.6.1.4.1.429.1.6.4.1.1.2
Equates to modem's S16 register.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmTfTestTime		1.3.6.1.4.1.429.1.6.4.1.1.3
Duration in seconds that the tests specified by mdmTfTestControl are to execute. Default=0(indefinate).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmTfV54		1.3.6.1.4.1.429.1.6.4.1.1.4
Corresponds to modem's &T register and provides tests specified by V.54. Default=normal.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmTfV54Errors		1.3.6.1.4.1.429.1.6.4.1.1.5
The number of errors occurring during the last V54 loopback test.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTfATG		1.3.6.1.4.1.429.1.6.4.1.1.6
ATG data from the modem
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

mdmTfDialInToneTest		1.3.6.1.4.1.429.1.6.4.1.1.7
This object is used to enable Dial in Tone Tests.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmTfToneTestCallRef		1.3.6.1.4.1.429.1.6.4.1.1.8
This object is used to send the call reference info with the tone test.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..53)

mdmTfToneTable		1.3.6.1.4.1.429.1.6.4.2
Table for modem tone tests
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmTfToneEntry

mdmTfToneEntry		1.3.6.1.4.1.429.1.6.4.2.1
Objects for modem tone tests
Status: optional	Access: not-accessible
OBJECT-TYPE
	MdmTfToneEntry

mdmTfToneIndex		1.3.6.1.4.1.429.1.6.4.2.1.1
A value used to ID this modem
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTfTxFreq		1.3.6.1.4.1.429.1.6.4.2.1.2
Modem tone test TX frequency
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	300..4000

mdmTfTxAmpl		1.3.6.1.4.1.429.1.6.4.2.1.3
Modem tone test TX amplitude
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	-40..0

mdmTfRxFreq		1.3.6.1.4.1.429.1.6.4.2.1.4
Modem tone test RX frequency
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	0..5000

mdmTfRxAmpl		1.3.6.1.4.1.429.1.6.4.2.1.5
Modem tone test RX amplitude
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTfRspndrTable		1.3.6.1.4.1.429.1.6.4.3
Table for 105/102 responder test results.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmTfRspndrEntry

mdmTfRspndrEntry		1.3.6.1.4.1.429.1.6.4.3.1
Objects containing the 105/102 responder test result dB levels and test status values.
Status: optional	Access: not-accessible
OBJECT-TYPE
	MdmTfRspndrEntry

mdmTfRspndrIndex		1.3.6.1.4.1.429.1.6.4.3.1.1
A value used to ID this modem.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTf404FarNearLvl		1.3.6.1.4.1.429.1.6.4.3.1.2
404 Hz tone at -16 dB loss test level. Far to near. Level in 0.1 dB resolution.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTf404NearFarLvl		1.3.6.1.4.1.429.1.6.4.3.1.3
404 Hz tone at -16 dB loss test level. Near to far. Level in 0.1 dB resolution.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTf1004FarNearLvl		1.3.6.1.4.1.429.1.6.4.3.1.4
1004 Hz tone at -16 dB loss test level. Far to near. Level in 0.1 dB resolution.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTf1004NearFarLvl		1.3.6.1.4.1.429.1.6.4.3.1.5
1004 Hz tone at -16 dB loss test level. Near to far. Level in 0.1 dB resolution.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTf2804FarNearLvl		1.3.6.1.4.1.429.1.6.4.3.1.6
2804 Hz tone at -16 dB loss test level. Far to near. Level in 0.1 dB resolution.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTf2804NearFarLvl		1.3.6.1.4.1.429.1.6.4.3.1.7
2804 Hz tone at -16 dB loss test level. Near to far. Level in 0.1 dB resolution.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTfCmsgFarNearLvl		1.3.6.1.4.1.429.1.6.4.3.1.8
C-message test level. Far to near. Level in 0.1 dB resolution.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTfCmsgNearFarLvl		1.3.6.1.4.1.429.1.6.4.3.1.9
C-message test level. Near to far. Level in 0.1 dB resolution.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTfCnotchFarNearLvl		1.3.6.1.4.1.429.1.6.4.3.1.10
C-notch test level. Far to near. Level in 0.1 dB resolution.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTfCnotchNearFarLvl		1.3.6.1.4.1.429.1.6.4.3.1.11
C-notch test level. Near to far. Level in 0.1 dB resolution.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmtTfSigNoiseFarNearLvl		1.3.6.1.4.1.429.1.6.4.3.1.12
Signal to noise ratio level. Far to near. Level in 0.1 dB resolution.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmtTfSigNoiseNearFarLvl		1.3.6.1.4.1.429.1.6.4.3.1.13
Signal to noise ratio level. Near to far. Level in 0.1 dB resolution.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTf404FarNearSts		1.3.6.1.4.1.429.1.6.4.3.1.14
404 Hz tone at -16 dB loss test status. Far to near. Default=noTest(1).
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	noTest(1), success(2), noResponder(3), unsupported(4), timeOut(5), noToneDetected(6)

mdmTf404NearFarSts		1.3.6.1.4.1.429.1.6.4.3.1.15
404 Hz tone at -16 db loss test status. Near to far. Default=noTest(1).
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	noTest(1), success(2), noResponder(3), unsupported(4), timeOut(5), noToneDetected(6)

mdmTf1004FarNearSts		1.3.6.1.4.1.429.1.6.4.3.1.16
1004 Hz tone at -16 dB loss test status. Far to near. Default=noTest(1).
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	noTest(1), success(2), noResponder(3), unsupported(4), timeOut(5), noToneDetected(6)

mdmTf1004NearFarSts		1.3.6.1.4.1.429.1.6.4.3.1.17
1004 Hz tone at -16 dB loss test status. Near to far. Default=noTest(1).
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	noTest(1), success(2), noResponder(3), unsupported(4), timeOut(5), noToneDetected(6)

mdmTf2804FarNearSts		1.3.6.1.4.1.429.1.6.4.3.1.18
2804 Hz tone at -16 dB loss test status. Far to near. Default=noTest(1).
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	noTest(1), success(2), noResponder(3), unsupported(4), timeOut(5), noToneDetected(6)

mdmTf2804NearFarSts		1.3.6.1.4.1.429.1.6.4.3.1.19
2804 Hz tone at -16 dB loss test status. Near to far. Default=noTest(1).
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	noTest(1), success(2), noResponder(3), unsupported(4), timeOut(5), noToneDetected(6)

mdmTfCmsgFarNearSts		1.3.6.1.4.1.429.1.6.4.3.1.20
C-message test status. Far to near. Default=noTest(1).
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	noTest(1), success(2), noResponder(3), unsupported(4), timeOut(5), noToneDetected(6)

mdmTfCmsgNearFarSts		1.3.6.1.4.1.429.1.6.4.3.1.21
C-message test status. Near to far. Default=noTest(1).
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	noTest(1), success(2), noResponder(3), unsupported(4), timeOut(5), noToneDetected(6)

mdmTfCnotchFarNearSts		1.3.6.1.4.1.429.1.6.4.3.1.22
C-notch test status. Far to near. Default=noTest(1).
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	noTest(1), success(2), noResponder(3), unsupported(4), timeOut(5), noToneDetected(6)

mdmTfCnotchNearFarSts		1.3.6.1.4.1.429.1.6.4.3.1.23
C-notch test status. Near to far. Default=noTest(1).
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	noTest(1), success(2), noResponder(3), unsupported(4), timeOut(5), noToneDetected(6)

mdmTfSigNoiseFarNearSts		1.3.6.1.4.1.429.1.6.4.3.1.24
Signal to noise ratio status. Far to near. Default=noTest(1).
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	noTest(1), success(2), noResponder(3), unsupported(4), timeOut(5), noToneDetected(6)

mdmTfSigNoiseNearFarSts		1.3.6.1.4.1.429.1.6.4.3.1.25
Signal to noise ratio status. Near to far. Default=noTest(1).
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	noTest(1), success(2), noResponder(3), unsupported(4), timeOut(5), noToneDetected(6)

mdmTf0dB1004FarNearLvl		1.3.6.1.4.1.429.1.6.4.3.1.26
1004 Hz tone at 0 db loss test level. Far to near. Level in 0.1 dB resolution.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTf0dB1004NearFarLvl		1.3.6.1.4.1.429.1.6.4.3.1.27
1004 Hz tone at 0 db loss test level. Near to far. Level in 0.1 dB resolution.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTf0dB1004FarNearSts		1.3.6.1.4.1.429.1.6.4.3.1.28
1004 Hz tone at 0 db loss test status. Far to near. Default=noTest(1).
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	noTest(1), success(2), noResponder(3), unsupported(4), timeOut(5), noToneDetected(6)

mdmTf0dB1004NearFarSts		1.3.6.1.4.1.429.1.6.4.3.1.29
1004 Hz tone at 0 db loss test status. Near to Far. Default=noTest(1).
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	noTest(1), success(2), noResponder(3), unsupported(4), timeOut(5), noToneDetected(6)

mdmDi		1.3.6.1.4.1.429.1.6.5
OBJECT IDENTIFIER

mdmDiTable		1.3.6.1.4.1.429.1.6.5.1
Table of DTE interface objects. The number of table entries is specified by modemNumber.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmDiEntry

mdmDiEntry		1.3.6.1.4.1.429.1.6.5.1.1
Objects that define the DTE interface for a modem.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmDiEntry

mdmDiIndex		1.3.6.1.4.1.429.1.6.5.1.1.1
The index for the DTE interface table contains the unique value associated with this modem as defined in the chassis mib entity table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmDiEscCodeGuardTime		1.3.6.1.4.1.429.1.6.5.1.1.2
Duration in 50ths of a second of idle time that must precede and follow the modem's command mode escape code. Default=50.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmDiLocalEscChar		1.3.6.1.4.1.429.1.6.5.1.1.3
Decimal equivalent of the character that is used to escape to on-line command mode. Values between 128 and 255 disable the escape code. Default=43(+).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmDiCarriageRetChar		1.3.6.1.4.1.429.1.6.5.1.1.4
Specifies the decimal equivalent of the carriage return character. Default=13.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmDiLineFeedChar		1.3.6.1.4.1.429.1.6.5.1.1.5
Specifies the decimal equivalent of the line feed character. Default=10.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmDiBackspaceChar		1.3.6.1.4.1.429.1.6.5.1.1.6
Specifies the decimal equivalent of the backspace character. Default=8.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmDiDelAsBackspace		1.3.6.1.4.1.429.1.6.5.1.1.7
Defines functionality of the delete key. Acts either to delete the character the cursor is currently on or acts the same as the backspace key. Default=delete.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	delete(1), backspace(2)

mdmDiResetOnDtrEna		1.3.6.1.4.1.429.1.6.5.1.1.8
When enabled, this option will cause the modem to restart when the DTR control signal drops. Default=disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmDiResultCodePauseDis		1.3.6.1.4.1.429.1.6.5.1.1.9
When enabled, the modem pauses 250ms before transmission of any result code. Default=enable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmDiInterbridgeEna		1.3.6.1.4.1.429.1.6.5.1.1.10
When enabled, the modem operates in a mode that is compatible with an 'Appletalk InterBridge Network'. Default=disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmDiBreakLen		1.3.6.1.4.1.429.1.6.5.1.1.11
Defines the duration of break characters that are sent to the DTE in ARQ mode. Defined in 10ms increments. Default=10(100ms).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmDiXonChar		1.3.6.1.4.1.429.1.6.5.1.1.12
Defines the decimal equivalent of the Xon character. This character will be used when software flow control is enabled. Default=17.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmDiXoffChar		1.3.6.1.4.1.429.1.6.5.1.1.13
Defines the decimal equivalent of the xoff character. This character will be used when software flow control is enabled. Default=19.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmDiDsrPulseTime		1.3.6.1.4.1.429.1.6.5.1.1.14
Duration in 20 millisecond increments that the DSR signal is pulsed when the modem is configured for pulsed DSR mode. Default=150.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..150

mdmDiRtsCtsDelay		1.3.6.1.4.1.429.1.6.5.1.1.15
Duration in 10 millisecond increments that the modem delays setting CTS after detecting the presence of RTS. Default=1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmDiHiSpeedResCodeEna		1.3.6.1.4.1.429.1.6.5.1.1.16
Determines if connection establishment result codes above 9600 are sent to the DTE. Default=enable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmDiCmdLocalEchoEna		1.3.6.1.4.1.429.1.6.5.1.1.17
Defines whether or not the characters transmitted by the DTE are echoed back when in command mode. Default=disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmDiDataModeEchoEna		1.3.6.1.4.1.429.1.6.5.1.1.18
Defines whether or not the DTE's transmitted data is echoed back durring a connection(half duplex). Default=disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmDiDteDataRateMode		1.3.6.1.4.1.429.1.6.5.1.1.19
Defines how the modem determines the DTE data rate. When set to the default, follows link rate, the modem switches the DTE speed to match the link rate. When set to fixed, the DTE speed remains at the default DTE data rate or the rate of the last AT command. When set to ARQ fixed-Non ARQ follows the dte speed remains fixed for ARQ calls and follows the link rate for non ARQ calls.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	followsLinkRate(1), fixed(2), arqFixedNonArqFollows(3)

mdmDiCdOverride		1.3.6.1.4.1.429.1.6.5.1.1.20
Defines the operation of the CD(Carrier Detect) signal. When overridden the CD signal is always asserted. Default=normal.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmDiDtrOverride		1.3.6.1.4.1.429.1.6.5.1.1.21
Defines operation with regard to DTR. When overridden the DTR signal is always assumed to be present. Default=normal.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmDiDsrOverride		1.3.6.1.4.1.429.1.6.5.1.1.22
Determines the functionality of the modem's DSR signal. Default=Override.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dsrOveridden(1), modemControled(2), pulsedCtsFollowsCd(3), pulsed(4), dsrEqualsCd(5), normalCtsFollowsCd(6)

mdmDiEiaLineStatus		1.3.6.1.4.1.429.1.6.5.1.1.23
Provides a mechanism for the console to determine the current state of the DTE's EIA signals.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

mdmDiTransmitFlowCntl		1.3.6.1.4.1.429.1.6.5.1.1.24
Determines if transmit flow control is enabled and if so whether it is hardware or software. Default=none.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), hardware(2), software(3), hardwareAndSoftware(4)

mdmDiSoftwareRxFlowCntl		1.3.6.1.4.1.429.1.6.5.1.1.25
Determines if receive software flow control is enabled as well as what type. Default=none.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), xonXoffLocalRemote(2), xonXoffLocal(3), hpHostMode(4), hpTerminalMode(5), localIncommingXonXoff(6)

mdmDiHardwareRxFlowCntl		1.3.6.1.4.1.429.1.6.5.1.1.26
Determines if receive hardware flow control is enabled as well as how it is implemented. Default=RTS ignored.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	rtsCtsDelayed(1), rtsIgnored(2), dataOnRtsHigh(3)

mdmDiBreakHandling		1.3.6.1.4.1.429.1.6.5.1.1.27
Defines the method used to handle received breaks. When defined as destructive the modem's transmit data buffer is flushed. When defined as expidited, the break preceeds any pending data in the transmit buffer. Default=Destructive,Expidited.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	destructiveNotSent(1), destructiveExpedited(2), nondestructiveExpedited(3), nondestructiveNotSent(4)

mdmDiDteNvramLock		1.3.6.1.4.1.429.1.6.5.1.1.28
When locked, prohibits the DTE user from changing any of the NVRAM settings in the modem. Default=unlocked.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmDiSerialFormat		1.3.6.1.4.1.429.1.6.5.1.1.29
Defines the data bits and parity of the modem's DTE. Used in situations where the attached DTE is unable to send AT commands to initialize the DTE format. Default=8 bit no parity.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	bit8NoParity(1), bit7EvenParity(2), bit7OddParity(3), bit7MarkParity(4)

mdmDiDefaultDteDataRate		1.3.6.1.4.1.429.1.6.5.1.1.30
Defines the data rate of the DTE. Useful in those cases where the DTE is incapable of sending an AT command to initialize the data rate and a fixed data rate is required. Default=9600.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	bps110(1), bps300(2), bps600(3), bps1200(4), bps2400(5), bps4800(6), bps9600(8), bps19K(12), bps38K(13), unknown(16), bps57K(17), bps115K(22)

mdmDiRemAccessMsg		1.3.6.1.4.1.429.1.6.5.1.1.31
Specifies if the modem is to send the 'Modem Unavailable' message to the DTE when the DTE attempts to send data to a modem that is curently in command mode with a remote DTE. Default = enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmDiV25DteDataRate		1.3.6.1.4.1.429.1.6.5.1.1.32
Defines the DTE Data Rates supported for V25 bis.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	bps1200(1), bps2400(2), bps4800(3), bps7200(4), bps9600(5), bps12K(6), bps14K(7), bps16K(8), bps19K(9), bps21K(10), bps24K(11), bps26K(12), bps28K(13)

mdmDiSrc		1.3.6.1.4.1.429.1.6.5.1.1.33
Specifies either NIC or Packet Bus as the source for the DTE interface.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	nic(1), packetBus(2)

mdmDiSlot		1.3.6.1.4.1.429.1.6.5.1.1.34
Specifies the slot address as the DTE interface source when mdmdiSrc is configured for Packet Bus.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	1..16

mdmDiBusyClock		1.3.6.1.4.1.429.1.6.5.1.1.35
specifies whether the modem will support either the current transmit clock or a new busy out.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	extClock1(1), busyOut(2)

mdmDiAtString		1.3.6.1.4.1.429.1.6.5.1.1.36
Provides an interface for issuing an AT command to the modem. Not implemented as a command so as to allow the object to be saved to NVRAM and subsequently configured during power-up.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..41)

mdmDiDtrRecognitionTime		1.3.6.1.4.1.429.1.6.5.1.1.37
S25 register tells the modem how quickly to react when DTR transitions from off to on. Default is 20. Increments are in 10 ms.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmSc		1.3.6.1.4.1.429.1.6.6
OBJECT IDENTIFIER

mdmScTable		1.3.6.1.4.1.429.1.6.6.1
Table of configurable objects which determine the operation of the Signal Converter. The quantity of entries in this table is defined by modemNumber.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmScEntry

mdmScEntry		1.3.6.1.4.1.429.1.6.6.1.1
Objects that define the operation of the modem's Signal Converter.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmScEntry

mdmScIndex		1.3.6.1.4.1.429.1.6.6.1.1.1
The unique value found in the chassis mib entity relation table that references this modem.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmScLinkRateSelect		1.3.6.1.4.1.429.1.6.6.1.1.2
Determines if the link will run at a fixed or variable data rate. Default=variable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	variable(1), bps300(2), bps1200(3), bps2400(4), bps4800(5), bps7200(6), bps9600(7), bps12000(8), bps14400(9), bps16800(10), bps19200(11), bps21600(12), bps24000(13), bps26400(14), bps28800(15), bps31200(16), bps33600(17), bps33333(18), bps37333(19), bps41333(20), bps42666(21), bps44000(22), bps45333(23), bps46666(24), bps48000(25), bps49333(26), bps50666(27), bps52000(28), bps53333(29), bps54666(30), bps56000(31), bps57333(32), bps64000(33), bps28000(34), bps29333(35), bps30666(36), bps32000(37), bps34666(38), bps36000(39), bps38666(40), bps40000(41), bps58666(42), bps60000(43), bps61333(44), bps62666(45)

mdmScNonArqBufSize		1.3.6.1.4.1.429.1.6.6.1.1.3
Sets the sizer of the transmit buffer for non-ARQ mode operation to either 128 bytes or 1.5K. The smaller size is for low speed interactive applications, the large size is for file transfer. Default=128.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	bytes1500(1), bytes128(2)

mdmScNonMnpDataCapture		1.3.6.1.4.1.429.1.6.6.1.1.4
Causes received characters to be buffered when the modem is attempting to negotiate an MNP call and the remote modem is not. Default=disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmScSyncTimingSource		1.3.6.1.4.1.429.1.6.6.1.1.5
Specifies the clock source when operating in synchronous mode. Default=internal.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	internal(1), external(2), rxLinkClock(3)

mdmScHstMod		1.3.6.1.4.1.429.1.6.6.1.1.6
May be used to disable HST operation on USRobotics Dual Standard modems. Default=enable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScHiFreqEq		1.3.6.1.4.1.429.1.6.6.1.1.7
Allows modem's high frequency equalization to be disabled if it causes problems on shorter lines. Default=enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScBackChanRate		1.3.6.1.4.1.429.1.6.6.1.1.8
Specifies the lower speed used in the asymetrical (HST) mode of operation. The 300 bps setting is provided for compatibility with early HST modems. Default=450.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	bps450(1), bps300(2)

mdmScV21Mod		1.3.6.1.4.1.429.1.6.6.1.1.9
When enabled, the modem will answer both bell 103 and V.21 calls but originates only V.21 calls. Default=disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmScV32UnencodedMod		1.3.6.1.4.1.429.1.6.6.1.1.10
Allows unencoded modulation in V.32 mode. Although part of the CCITT V.32 recomendation it is rarely used. Default=disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmScV32Mod		1.3.6.1.4.1.429.1.6.6.1.1.11
Allows V.32 modulation to be disabled on USRobotics Dual Standard modems. Default=enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScBell208		1.3.6.1.4.1.429.1.6.6.1.1.12
Allows modems that support Bell 208 modulation to include Bell 208 as part of the negotiation sequence. Default=Bell 208 disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmScV32Bis		1.3.6.1.4.1.429.1.6.6.1.1.13
Allows V.32 bis modulation to be disabled. On USRobotics Dual Standard modems this may be useful in troublshooting HST operation. Default=V.32 bis enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScV32BisEnhance		1.3.6.1.4.1.429.1.6.6.1.1.14
Allows USRobotics V.32 Enahnced mode to be disabled for purposes of troubleshooting Default=enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScV32QuickRetrain		1.3.6.1.4.1.429.1.6.6.1.1.15
Allows the faster retrains that occur with USR's enhanced V.32 mode to be disabled for troubleshooting purposes. Default=enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScV23		1.3.6.1.4.1.429.1.6.6.1.1.16
Allows the modem to negotiate a V.23 connection(used in U.K.) after failing to negotiate a higher rate. Default=disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmScHiSpeedModulation		1.3.6.1.4.1.429.1.6.6.1.1.17
Defines the handshaking options used in negotiation of high speed calls. Default=CCITT V.32
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	v32(1), hst(2), bell208(3)

mdmScFallback		1.3.6.1.4.1.429.1.6.6.1.1.18
Defines whether or not the modem will be allowed to change protocols it detects a significant change in the line characteristics. If the modem is unable to maintain transmission with the current modulation technique it would fall back to a lower speed and if the line then improved it would upshift to a higher speed. Default=enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScV32TerboModeEnable		1.3.6.1.4.1.429.1.6.6.1.1.19
Allows the V32 Terbo mode to be disabled/enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmScV34ModeEnable		1.3.6.1.4.1.429.1.6.6.1.1.20
Allows V34 mode to be disabled/enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmScVFCSymRate2400		1.3.6.1.4.1.429.1.6.6.1.1.21
Allows the 2400 symbol rate to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFCSymRate2743		1.3.6.1.4.1.429.1.6.6.1.1.22
Allows the 2743 symbol rate to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFCSymRate2800		1.3.6.1.4.1.429.1.6.6.1.1.23
Allows the 2800 symbol rate to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFCSymRate3000		1.3.6.1.4.1.429.1.6.6.1.1.24
Allows the 3000 symbol rate to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFCSymRate3200		1.3.6.1.4.1.429.1.6.6.1.1.25
Allows the 3200 symbol rate to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFCSymRate3429		1.3.6.1.4.1.429.1.6.6.1.1.26
Allows the 3429 symbol rate to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFC8S2DMapping		1.3.6.1.4.1.429.1.6.6.1.1.27
Allows the 8S-2D mapping to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFC16S4DMapping		1.3.6.1.4.1.429.1.6.6.1.1.28
Allows the 16S-4D mapping to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFC32S2DMapping		1.3.6.1.4.1.429.1.6.6.1.1.29
Allows the 32S-2D mapping to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFC64S4DMapping		1.3.6.1.4.1.429.1.6.6.1.1.30
Allows the 64S-4D mapping to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFCNonLinearCoding		1.3.6.1.4.1.429.1.6.6.1.1.31
Allows the non-linear coding to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFCTxLevelDeviation		1.3.6.1.4.1.429.1.6.6.1.1.32
Allows the TX level deviation to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFCPreEmphasis		1.3.6.1.4.1.429.1.6.6.1.1.33
Allows the pre-emphasis to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFCPreCoding		1.3.6.1.4.1.429.1.6.6.1.1.34
Allows the precoding to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFCShaping		1.3.6.1.4.1.429.1.6.6.1.1.35
Allows the shaping to be disabled/enabled on V.FC modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScVFCModeEnable		1.3.6.1.4.1.429.1.6.6.1.1.36
Allows to disable/enable V.FC mode in order to troubleshoot a connection.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScV8		1.3.6.1.4.1.429.1.6.6.1.1.37
Allow V8 mode to be disabled/enabled
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmSCV8CallIndicator		1.3.6.1.4.1.429.1.6.6.1.1.38
Allow V.8. call indicater to be disabled/enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScV34pModeEnable		1.3.6.1.4.1.429.1.6.6.1.1.39
Allows V34 plus modulation mode to be disabled. (default=0/enabled)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmSc300		1.3.6.1.4.1.429.1.6.6.1.1.40
Restrict 300 baud negotiations. Register S48.0 Default is disable (0) restriction.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmSc1200		1.3.6.1.4.1.429.1.6.6.1.1.41
Restrict 1200 baud negotiations. Register S48.1 Default is disable (0) restriction.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmSc2400		1.3.6.1.4.1.429.1.6.6.1.1.42
Restrict 2400 baud negotiations. Register S48.2 Default is disable (0) restriction.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmScHighSpeed		1.3.6.1.4.1.429.1.6.6.1.1.43
Restrict highspeed baud negotiations. Register S48.3 Default is disable (0) restriction.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmScSelectiveReject		1.3.6.1.4.1.429.1.6.6.1.1.44
Selective Reject register S51.6 is a function of the V.42/LAPM protocol. The default is enable (1)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScPhExclusionDel		1.3.6.1.4.1.429.1.6.6.1.1.45
Enable/disable phone extension delay S51.7. Default is enable
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmScLinkRateAmpU		1.3.6.1.4.1.429.1.6.6.1.1.46
Minimum high-speed direction link speed Default=variable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	variable(1), bps300(2), bps1200(3), bps2400(4), bps4800(5), bps7200(6), bps9600(7), bps12000(8), bps14400(9), bps16800(10), bps19200(11), bps21600(12), bps24000(13), bps26400(14), bps28800(15), bps31200(16), bps33600(17), bps33333(18), bps37333(19), bps41333(20), bps42666(21), bps44000(22), bps45333(23), bps46666(24), bps48000(25), bps49333(26), bps50666(27), bps52000(28), bps53333(29), bps54666(30), bps56000(31), bps57333(32), bps64000(33), bps28000(34), bps29333(35), bps30666(36), bps32000(37), bps34666(38), bps36000(39), bps38666(40), bps40000(41), bps58666(42), bps60000(43), bps61333(44), bps62666(45)

mdmScLowerSpeedMin		1.3.6.1.4.1.429.1.6.6.1.1.47
Lower speed direction minimum Default=1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	variable(1), bps300(2), bps1200(3), bps2400(4), bps4800(5), bps7200(6), bps9600(7), bps12000(8), bps14400(9), bps16800(10), bps19200(11), bps21600(12), bps24000(13), bps26400(14), bps28800(15), bps31200(16), bps33600(17), bps33333(18), bps37333(19), bps41333(20), bps42666(21), bps44000(22), bps45333(23), bps46666(24), bps48000(25), bps49333(26), bps50666(27), bps52000(28), bps53333(29), bps54666(30), bps56000(31), bps57333(32), bps64000(33), bps28000(34), bps29333(35), bps30666(36), bps32000(37), bps34666(38), bps36000(39), bps38666(40), bps40000(41), bps58666(42), bps60000(43), bps61333(44), bps62666(45)

mdmScLowerSpeedMax		1.3.6.1.4.1.429.1.6.6.1.1.48
Lower speed direction maximum Default=1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	variable(1), bps300(2), bps1200(3), bps2400(4), bps4800(5), bps7200(6), bps9600(7), bps12000(8), bps14400(9), bps16800(10), bps19200(11), bps21600(12), bps24000(13), bps26400(14), bps28800(15), bps31200(16), bps33600(17), bps33333(18), bps37333(19), bps41333(20), bps42666(21), bps44000(22), bps45333(23), bps46666(24), bps48000(25), bps49333(26), bps50666(27), bps52000(28), bps53333(29), bps54666(30), bps56000(31), bps57333(32), bps64000(33), bps28000(34), bps29333(35), bps30666(36), bps32000(37), bps34666(38), bps36000(39), bps38666(40), bps40000(41), bps58666(42), bps60000(43), bps61333(44), bps62666(45)

mdmScX2Client		1.3.6.1.4.1.429.1.6.6.1.1.49
X2 Client Mode Disable Default=enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

mdmScX2Server		1.3.6.1.4.1.429.1.6.6.1.1.50
X2 Server Mode Disable Default=enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

mdmScX2Symmetric		1.3.6.1.4.1.429.1.6.6.1.1.51
X2 Symmetric Mode Disable Default=enable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

mdmScX2HighPowerConst		1.3.6.1.4.1.429.1.6.6.1.1.52
This object is used to enable/disable the X2 high-power constellation. This object is only valid in countries, where it is legal. It corresponds to S Register 76.7 Default = Disable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmScPiafs		1.3.6.1.4.1.429.1.6.6.1.1.53
This object is used to enable/disable PIAFS protocol. It corresponds to S Register 72.4 Default = enable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScPiafsV42bis		1.3.6.1.4.1.429.1.6.6.1.1.54
This object is used to enable/disable PIAFS V42bis compression protocol. It corresponds to S Register 72.5. Default = enable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmScTxPwrLvl		1.3.6.1.4.1.429.1.6.6.1.1.55
This object configures the power level. It applies to S-register S82.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..31

mdmScTxPwrLvlApplied		1.3.6.1.4.1.429.1.6.6.1.1.56
This object configures where the power level is applied. It applies to S-register S81.0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	inputToFarEndOfCodec(1), outputOfTheServerModem(2)

mdmScX2Version2		1.3.6.1.4.1.429.1.6.6.1.1.57
This object is the x2 Version 2 Modulation. It applies to S-register S81.1
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

mdmScV34Fallback		1.3.6.1.4.1.429.1.6.6.1.1.58
This object is the x2 fallback to v34. It applies to S-register S76.3
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

mdmScV90Analogue		1.3.6.1.4.1.429.1.6.6.1.1.59
This object controls the enable/disable of the V.90 client modulation.Default=Enable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

mdmScV90Digital		1.3.6.1.4.1.429.1.6.6.1.1.60
This object controls the enable/disable of the V.90 server modulation.Default=Enable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

mdmScV90AllDigital		1.3.6.1.4.1.429.1.6.6.1.1.61
This object controls the enable/disable of the V.90 symmetric modulation. Default=Enable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

mdmCc		1.3.6.1.4.1.429.1.6.7
OBJECT IDENTIFIER

mdmCcTable		1.3.6.1.4.1.429.1.6.7.1
A table containing the call control parameters for each modem in the chassis.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmCcEntry

mdmCcEntry		1.3.6.1.4.1.429.1.6.7.1.1
Call control parameters for a modem. These define the sequence of operation related to how a call is negotiated.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmCcEntry

mdmCcIndex		1.3.6.1.4.1.429.1.6.7.1.1.1
The index which uniquely identifies the modem to which this entry is applicable. The value corresponds to the value of the index to the entity table in the chassis MIB that corresponds to the same modem.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCcDialDelay		1.3.6.1.4.1.429.1.6.7.1.1.2
Defines the number of seconds the modem waits between going off hook and begining to dial. Ignored when result code options 2,4,6,or 7 are active. Default=2.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmCcWaitForCarrier		1.3.6.1.4.1.429.1.6.7.1.1.3
Defines the number of seconds the modem will wait for a carrier signal after dialing. Default=60.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmCcInactivityTimer		1.3.6.1.4.1.429.1.6.7.1.1.4
Sets the duration (in seconds) that the modem will maintain a connection when there is no activity on the phone line. The feature is disabled when set to 0. Default=0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmCcAutoDialOnDtrEna		1.3.6.1.4.1.429.1.6.7.1.1.5
When enabled the modem will dial the number present in mdmCCPhoneString0 when the DTR signal transitions from low to high. Default=disable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCcAutoDialOnPwrUpEna		1.3.6.1.4.1.429.1.6.7.1.1.6
When enabled, the modem will dial the number present in mdmCcPhoneString0 on power up or after a reset. Default=disable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCcGhostPortLockEna		1.3.6.1.4.1.429.1.6.7.1.1.7
When enabled, the modem requires that DTR go low before it will accept another call. The modem also implements a Fast Connect mode where CD is asserted before the link negotiation is complete. Default=disable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCcQuietResultCodes		1.3.6.1.4.1.429.1.6.7.1.1.8
Determines whether or not the modem transmits result codes to the DTE. Default=noResult(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	displayResult(1), noResult(2), originateOnly(3)

mdmCcResponseMode		1.3.6.1.4.1.429.1.6.7.1.1.9
Determines whether the modem transmits result codes in the verbal or numeric mode. Default=verbal(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	numeric(1), verbal(2)

mdmCcResultCodeOptions		1.3.6.1.4.1.429.1.6.7.1.1.10
Defines one of eight result code subsets and also defines indirectly how the modem reacts to dial tone etc. Equates to the modem's X register Default=1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

mdmCcArqResultCodeMode		1.3.6.1.4.1.429.1.6.7.1.1.11
Defines whether or not the ARQ result codes are sent to the DTE on connection(if result codes are enabled). Default=arqResultsEnabled(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	arqResultsDisabled(1), arqResultsEnabled(2), includeHstV32(3), includeProtocol(4)

mdmCcEscCodeRsp		1.3.6.1.4.1.429.1.6.7.1.1.12
Defines the action of the modem in response to the escape code(+++). The default value is determined by the state of Dip switch 2-3 on power up.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	goOnHook(1), enterCommandMode(2), ignoreEscCode(3)

mdmCcAtRecognition		1.3.6.1.4.1.429.1.6.7.1.1.13
Determines which, if any, AT commands the modem will recognize or accept from the DTE. Default=ignore(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ignore(1), queryOnly(2), enableAll(3)

mdmCcMgmtSysMsgDis		1.3.6.1.4.1.429.1.6.7.1.1.14
Determines if the modem is to send special result codes, triggered by user conflicts with the management system, to the DTE. Default=enable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmCcV32ToneDuration		1.3.6.1.4.1.429.1.6.7.1.1.15
Specifies the duration (in 10ths of a second) that the modem transmits the 3000/600 Hz answer tones for V.32 handshaking. A setting of 0 eliminates these tones and will result in faster connect times for V.21 and V.23 calls. Default=8.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmCcAutoAnswer		1.3.6.1.4.1.429.1.6.7.1.1.17
Determines the number of rings that the modem will answer calls on. When set to 0 the modem can only originate calls. Default=1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmCcAnswerInOrigMode		1.3.6.1.4.1.429.1.6.7.1.1.18
When enabled the modem will answer calls using the sequence normaly used by the originating modem. Default=disable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCcArqBufWait		1.3.6.1.4.1.429.1.6.7.1.1.19
Sets the duration (in seconds) that the modem waits on an ARQ call before clearing the transmit buffer and dropping carrier after DTR drops. This is to allow time for the remote modem to acknowledge receipt of all transmitted data. Default=0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmCcPhoneString0		1.3.6.1.4.1.429.1.6.7.1.1.20
Phone number stored in modem's non volitile memory. Useful in providing quick access to frequently called numbers. In addition mdmCcPhoneString0 is used for the dial on power up and dial on DTR options.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..36)

mdmCcPhoneString1		1.3.6.1.4.1.429.1.6.7.1.1.21
Phone number stored in the modem's non volitile memory, useful for providing quick access to frequently called numbers.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..36)

mdmCcPhoneString2		1.3.6.1.4.1.429.1.6.7.1.1.22
Phone number stored in the modem's non volitile memory, useful in providing quick access to frequently called numbers.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..36)

mdmCcPhoneString3		1.3.6.1.4.1.429.1.6.7.1.1.23
Phone number stored in the modem's non volitile memory, useful in providing quick access to frequently called numbers.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..36)

mdmCcErrorCntlMode		1.3.6.1.4.1.429.1.6.7.1.1.24
Defines if the modem is operating in synchronous or asynchronous mode and how it responds relative to negotiation of error control on asynchronous connections. When set to the default, normalArq(3), the modem attempts to connect with error control but if unable to negotiate it connects anyway. When set to none(1), async connections do not attempt to use error control. When set to arqOnly(4), the modem will hang up if unable to negotiate error contol. When set to syncMode(2), the modem will not connect asynchronously.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), syncMode(2), normalArq(3), arqOnly(4), v25bisChar(5), v25bisBit(6)

mdmCcMiMic		1.3.6.1.4.1.429.1.6.7.1.1.25
Specifies whether the modem will recognize MI/MIC closure as the mechanism for detecting incomming calls. Default=disable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCcMnpWith1200		1.3.6.1.4.1.429.1.6.7.1.1.26
Determines if the modem will include MNP/V42 negotiation on 1200 bps connections. Default=enable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmCcMnpWith2400		1.3.6.1.4.1.429.1.6.7.1.1.27
Determines if the modem will include MNP/V43 negotiation on 2400 bps calls. default=enable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmCcMnpWithV32		1.3.6.1.4.1.429.1.6.7.1.1.28
Determines if the modem will include MNP/V42 negotiation on V.32 connections. Default=enable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmCcMnpTimeout		1.3.6.1.4.1.429.1.6.7.1.1.29
Specifies the MNP/V42 link request timeout for negotiation of 1200 and 2400 bps calls. Default=5.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..14

mdmCcV21V23FallBackTimer		1.3.6.1.4.1.429.1.6.7.1.1.30
V21/V23 fallback timer, 1/10 sec. NVRAM S Register S29. Default=20
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmCcAddnlAnswToneDur		1.3.6.1.4.1.429.1.6.7.1.1.31
Additional answer tone duration, 1/10 sec. NVRAM S Register S49. Default=16.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmCcBillingDelayPeriod		1.3.6.1.4.1.429.1.6.7.1.1.32
Billing Delay Period. 1/50 sec. NVRAM S Register S50. Default=100.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmCcCarrierAccessCode1		1.3.6.1.4.1.429.1.6.7.1.1.33
The DNIS Carrier Access Code (CAC) Number. This is a string which contains a number from 1 to 10 digits (e.g. 9501755). This is the 1st of 3 CACs.
Status: optional	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..10)

mdmCcCarrierAccessCode2		1.3.6.1.4.1.429.1.6.7.1.1.34
The DNIS Carrier Access Code (CAC) Number. This is a string which contains a number from 1 to 10 digits. This is the 2nd of 3 CACs.
Status: optional	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..10)

mdmCcCarrierAccessCode3		1.3.6.1.4.1.429.1.6.7.1.1.35
The DNIS Carrier Access Code (CAC) Number. This is a string which contains a number from 1 to 10 digits. This is the 3rd of 3 CACs.
Status: optional	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..10)

mdmCcCallingInitStr1		1.3.6.1.4.1.429.1.6.7.1.1.36
This is the Carrier Access Code (CAC) initialization string. This string is a configuration string of 1 to 30 characters (e.g. &F, &F&B1&R1, etc.) This string does NOT include the AT attention prefix. This is the 1st of 4 CAC init strings.
Status: optional	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..40)

mdmCcCallingInitStr2		1.3.6.1.4.1.429.1.6.7.1.1.37
This is the Carrier Access Code (CAC) initialization string. This string is 1 to 30 characters. It does NOT include the AT attention prefix. It is the 2nd of 4 CAC init strings.
Status: optional	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..40)

mdmCcCallingInitStr3		1.3.6.1.4.1.429.1.6.7.1.1.38
This is the Carrier Access Code (CAC) initialization string. This is a string of 1 to 30 characters. It does NOT include the AT attention prefix. This is the 3rd of 4 CAC init strings.
Status: optional	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..40)

mdmCcCallingInitStr4		1.3.6.1.4.1.429.1.6.7.1.1.39
This is the Carrier Access Code (CAC) initialization string. This is a string of 1 to 30 characters. It does NOT include the AT attention prefix. This is the 4th of 4 CAC init strings.
Status: optional	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..40)

mdmCcDataFaxMode		1.3.6.1.4.1.429.1.6.7.1.1.40
Gives the current Data/FAX mode of the modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dataMode(1), faxClass1Mode(2), dataFaxClass1Mode(3), faxClass2Mode(4), dataFaxClass2Mode(5)

mdmCcT1CallSetupProc		1.3.6.1.4.1.429.1.6.7.1.1.41
Determines T1 call setup procedures used. Choices are 'normal' or 'none'. None assumes a dedicated (leased) DS0 assigned to the modem. Default=normalSetup(1).
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	normalSetup(1), noSetup(2)

mdmCcT1DialToneType		1.3.6.1.4.1.429.1.6.7.1.1.42
Determines if MF or DTMF tones are used for T1 signaling. Default = mfTones(1).
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	mfTones(1), dtmfTones(2)

mdmCcT1KpStMfTones		1.3.6.1.4.1.429.1.6.7.1.1.43
Determines the usage of KP and ST MF tone encapsulation of the dial sequence. Default=enable(1).
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmCcT1CallInitStrUse		1.3.6.1.4.1.429.1.6.7.1.1.44
Determines if calling init strings are used or not. Default=enable(1).
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmCcT1CallInitStrBase		1.3.6.1.4.1.429.1.6.7.1.1.45
Determines if the calling init strings are based upon DNIS or ANI. Default=dnisBase(1).
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	dnisBase(1), aniBase(2)

mdmCcIntBlackListDis		1.3.6.1.4.1.429.1.6.7.1.1.46
Disable BlackList restriction in the international modems. Default=0 (enable) s40.1 reg
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmCcOffHookRestrict		1.3.6.1.4.1.429.1.6.7.1.1.47
Disable off-hook restriction in the international modems. Default=0 (enable) S40.2 reg
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmCcT1DialInAniDig		1.3.6.1.4.1.429.1.6.7.1.1.48
Sets the number of ANI digits allowed in incoming calls. Default = 0.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..12

mdmCcT1DialInDnisDig		1.3.6.1.4.1.429.1.6.7.1.1.49
Sets the number of DNIS/DID digits allowed in incoming calls. Default = 0.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..12

mdmCcNoPbNoConnEna		1.3.6.1.4.1.429.1.6.7.1.1.50
Sets if to answer a call when there is no Packet Bus link. Normal is the Default =0
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCcIdleDiscPatt		1.3.6.1.4.1.429.1.6.7.1.1.51
Idle disconnect pattern sent to the T1 NAC. Normal values: USA = 1, international = 84. Default = 1. Configure the T1 identically. Consult the help screen, user manual or US Robotics before changing. Modem register S71.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmCcMnp10		1.3.6.1.4.1.429.1.6.7.1.1.52
S61.4 register disable/enable MNP10 originate mode.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCcMnp10Ec		1.3.6.1.4.1.429.1.6.7.1.1.53
S61.5 register disable/enable MNP10EC originate mode.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCcAtzPbHandling		1.3.6.1.4.1.429.1.6.7.1.1.54
ATZ handling over Packet Bus. S72 REG
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	normalAtz(1), atzPbIgnored(2), atzPbNvram(3)

mdmCcDefltPRISlot		1.3.6.1.4.1.429.1.6.7.1.1.55
Default dialout PRI slot. Default = 1
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..5

mdmCcExtDTMFToneSupport		1.3.6.1.4.1.429.1.6.7.1.1.56
Enable/Disable DTMF extended support. Default = disable
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCcDataOverVoice		1.3.6.1.4.1.429.1.6.7.1.1.57
Data Over Voice support originate S68.1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCc2100AnswerTone		1.3.6.1.4.1.429.1.6.7.1.1.58
Data Over Voice support answer S68.2.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCcEnableV120v42Bis		1.3.6.1.4.1.429.1.6.7.1.1.59
V.42bis Compression over V.120. S67.4
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCcHdlcLicIe		1.3.6.1.4.1.429.1.6.7.1.1.60
This object is to Enable\Disable LIC IE message for HDLC protocols. S Register S68.3
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCcDtmfTerminationTone		1.3.6.1.4.1.429.1.6.7.1.1.61
This object is to set the DTMF Termination Tone.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..16

mdmCcAfaxMaxRateSrvOpt20		1.3.6.1.4.1.429.1.6.7.1.1.62
This object is used to limit the maximum rate for an Analog Fax Connection. Service option 20. Upper nibble of the S94 register.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	bps2400(1), bps4800(2), bps7200(3), bps9600(4), bps12000(5), bps14400(6)

mdmCcAfaxMaxRateSrvOpt21		1.3.6.1.4.1.429.1.6.7.1.1.63
This object is used to limit the maximum rate for an Analog Fax Connection. Service option 21. Lower nibble of S94 register.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	bps2400(1), bps4800(2), bps7200(3), bps9600(4), bps12000(5), bps14400(6)

mdmEc		1.3.6.1.4.1.429.1.6.8
OBJECT IDENTIFIER

mdmEcTable		1.3.6.1.4.1.429.1.6.8.1
A table of Error Control Parameters for each modem in this system, the quantity of entries is given by modemNumber.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmEcEntry

mdmEcEntry		1.3.6.1.4.1.429.1.6.8.1.1
Configurable objects which define the modems error control operation.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmEcEntry

mdmEcIndex		1.3.6.1.4.1.429.1.6.8.1.1.1
This object contains the unique value assigned to this modem in the chassis mib entity relation table and is used as the mechanism for correctly indexing into this table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmEcMnp3Dis		1.3.6.1.4.1.429.1.6.8.1.1.2
Determines if the modem will negotiate for MNP level 3 error correction. Default=enable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmEcMnp4Dis		1.3.6.1.4.1.429.1.6.8.1.1.3
Determines if the modem will negotiate for MNP level 4 error correction. Default=enable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmEcMnpUnusual		1.3.6.1.4.1.429.1.6.8.1.1.4
Determines if the modem will attempt to negotiate for MNP operation used in some early 2400bps modems. Default=disable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmEcV42MnpHandshake		1.3.6.1.4.1.429.1.6.8.1.1.5
Determines what types of error correction the modem will attempt to negotiate. When configured for the default, full V.42 and MNP, the modem first tries to connect with V42 error control and then with MNP error control. When set to disable either V42 or MNP the modem will only attempt to negotiate the enabled protocol. When set to disable the V42 detect phase, it is not included in the handshaking process. This allows for faster connections between V42 modems.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableAll(1), enableV42disableMnp(2), disablev42enablemnp(3), disableDetectionPhase(4)

mdmCs		1.3.6.1.4.1.429.1.6.9
OBJECT IDENTIFIER

mdmCsTable		1.3.6.1.4.1.429.1.6.9.1
A table of modem status and call statistic parameters for each modem in the chassis.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmCsEntry

mdmCsEntry		1.3.6.1.4.1.429.1.6.9.1.1
Objects that define the modem status and statistics specific to a the current connection when the modem is on line or to the last connection when the modem is idle.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmCsEntry

mdmCsIndex		1.3.6.1.4.1.429.1.6.9.1.1.1
The index value which uniquely identifies the modem to which this entry is applicable. The value corresponds to the index of the same modem in the entity table of the chassis MIB.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsStatus		1.3.6.1.4.1.429.1.6.9.1.1.2
Current status of a modem including presence(idle), availability(disabled), and call progress states.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	idle(1), offHook(2), dialing(3), ringing(4), ringRcvd(5), linkNegotiation(6), onlineOriginate(7), onlineAnswer(8), localCommandMode(9), remoteCommandMode(10), lineBusiedOut(11), toneTest(12), responderTest105(13), responderTest102(14), failed(33), testingRom(49), testingRam(50), testingNvram(51), analogLoopback(52), localDigitalLoopback(53), remoteDigitalLoopback(54), selfTest(55), phoneTest(56), nonManagedDevice(57), slotEmpty(58), modemDisabled(59), notResponding(60), nonManagableDevice(61), miuFailed(62)

mdmCsLastNumberDialedOut		1.3.6.1.4.1.429.1.6.9.1.1.3
An ASCII string which represents the last phone number dialed by the modem.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..40)

mdmCsLastNumberDialedIn		1.3.6.1.4.1.429.1.6.9.1.1.4
An ASCII string representing the last number dialed in(if known). This is the 950-xxx (DNIS) number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..40)

mdmCsLastCallingPartyNum		1.3.6.1.4.1.429.1.6.9.1.1.5
An ASCII string representing the current or last party that called this modem. Only known in ANI applications.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..40)

mdmCsOriginateAnswer		1.3.6.1.4.1.429.1.6.9.1.1.6
Defines whether the last or current call was originated or answered.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	originateInOriginate(1), originateInAnswer(2), answerInOriginate(3), answerInAnswer(4)

mdmCsRings		1.3.6.1.4.1.429.1.6.9.1.1.7
Defines the quantity of rings detected before the DTE answered with DTR on the last incomming call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsDisconnectReason		1.3.6.1.4.1.429.1.6.9.1.1.8
Defines the reason that the last call was terminated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	dtrDrop(1), escapeSequence(2), athCommand(3), carrierLoss(4), inactivityTimout(5), mnpIncompatible(6), undefined(7), remotePassword(8), linkPassword(9), retransmitLimit(10), linkDisconnectMsgReceived(11), noLoopCurrent(12), invalidSpeed(13), unableToRetrain(14), managementCommand(15), noDialTone(16), keyAbort(17), lineBusy(18), noAnswer(19), voice(20), noAnswerTone(21), noCarrier(22), undetermined(23), v42SabmeTimeout(24), v42BreakTimeout(25), v42DisconnectCmd(26), v42IdExchangeFail(27), v42BadSetup(28), v42InvalidCodeWord(29), v42StringToLong(30), v42InvalidCommand(31), none(32), v32Cleardown(33), dialSecurity(34), remoteAccessDenied(35), loopLoss(36), ds0Teardown(37), promptNotEnabled(38), noPromptingInSync(39), nonArqMode(40), modeIncompatible(41), noPromptInNonARQ(42), dialBackLink(43), linkAbort(44), autopassFailed(45), pbGenericError(46), pbLinkErrTxPreAck(47), pbLinkErrTxTardyACK(48), pbTransmitBusTimeout(49), pbReceiveBusTimeout(50), pbLinkErrTxTAL(51), pbLinkErrRxTAL(52), pbTransmitMasterTimeout(53), pbClockMissing(54), pbReceivedLsWhileLinkUp(55), pbOutOfSequenceFrame(56), pbBadFrame(57), pbAckWaitTimeout(58), pbReceivedAckSequenceErr(59), pbReceiveOvrflwRNRFailed(60), pbReceiveMsgBufOvrflw(61), rcvdGatewayDiscCmd(62), tokenPassingTimeout(63), dspInterruptTimeout(64), mnpProtocolViolation(65), class2FaxHangupCmd(66), hstSpeedSwitchTimeout(67), tooManyUnacked(68), timerExpired(69), t1Glare(70), priDialoutRqTimeout(71), abortAnlgDstOvrIsdn(72), normalUserCallClear(73), normalUnspecified(74), bearerIncompatibility(75), protocolErrorEvent(76), abnormalDisconnect(77), invalidCauseValue(78), resourceUnavailable(79), remotHungUpDuringTraining(80), trainingTimeout(81), incomingModemNotAvailable(82), incomingInvalidBearerCap(83), incomingInvalidChannelID(84), incomingInvalidProgInd(85), incomingInvalidCallingPty(86), incomingInvalidCalledPty(87), incomingCallBlock(88), incomingLoopStNoRingOff(89), outgoingTelcoDisconnect(90), outgoingEMWinkTimeout(91), outgoingEMWinkTooShort(92), outgoingNoChannelAvail(93), dspReboot(94), noDSPRespToKA(95), noDSPRespToDisc(96), dspTailPtrInvalid(97), dspHeadPtrInvalid(98), dataProcessingGenericErr(99), timeslotUnavailable(100), gmtTimeNotSet(101), chasAwarenessNotAvailable(102), r2InvalidChannelDirection(103), r2ChannelBlockedByNetwork(104), r2Glare(105), r2OutgoingCallBlocked(106), r2DNISNotFound(107), r2SigCauseCongestion(108), r2SigCauseUnallocNumber(109), r2DSPFatalError(110), callBlacklisted(111)

mdmCsConnectFailReason		1.3.6.1.4.1.429.1.6.9.1.1.9
Defines the reason for failure if indeed the last call attempt failed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	dtrDrop(1), escapeSequence(2), athCommand(3), carrierLoss(4), inactivityTimout(5), mnpIncompatible(6), undefined(7), remotePassword(8), linkPassword(9), retransmitLimit(10), linkDisconnectMsgReceived(11), noLoopCurrent(12), invalidSpeed(13), unableToRetrain(14), managementCommand(15), noDialTone(16), keyAbort(17), lineBusy(18), noAnswer(19), voice(20), noAnswerTone(21), noCarrier(22), undetermined(23), v42SabmeTimeout(24), v42BreakTimeout(25), v42DisconnectCmd(26), v42IdExchangeFail(27), v42BadSetup(28), v42InvalidCodeWord(29), v42StringToLong(30), v42InvalidCommand(31), none(32), v32Cleardown(33), dialSecurity(34), remoteAccessDenied(35), loopLoss(36), ds0Teardown(37), promptNotEnabled(38), noPromptingInSync(39), nonArqMode(40), modeIncompatible(41), noPromptInNonARQ(42), dialBackLink(43), linkAbort(44), autopassFailed(45), pbGenericError(46), pbLinkErrTxPreAck(47), pbLinkErrTxTardyACK(48), pbTransmitBusTimeout(49), pbReceiveBusTimeout(50), pbLinkErrTxTAL(51), pbLinkErrRxTAL(52), pbTransmitMasterTimeout(53), pbClockMissing(54), pbReceivedLsWhileLinkUp(55), pbOutOfSequenceFrame(56), pbBadFrame(57), pbAckWaitTimeout(58), pbReceivedAckSequenceErr(59), pbReceiveOvrflwRNRFailed(60), pbReceiveMsgBufOvrflw(61), rcvdGatewayDiscCmd(62), tokenPassingTimeout(63), dspInterruptTimeout(64), mnpProtocolViolation(65), class2FaxHangupCmd(66), hstSpeedSwitchTimeout(67), tooManyUnacked(68), timerExpired(69), t1Glare(70), priDialoutRqTimeout(71), abortAnlgDstOvrIsdn(72), normalUserCallClear(73), normalUnspecified(74), bearerIncompatibility(75), protocolErrorEvent(76), abnormalDisconnect(77), invalidCauseValue(78), resourceUnavailable(79), remotHungUpDuringTraining(80), trainingTimeout(81), incomingModemNotAvailable(82), incomingInvalidBearerCap(83), incomingInvalidChannelID(84), incomingInvalidProgInd(85), incomingInvalidCallingPty(86), incomingInvalidCalledPty(87), incomingCallBlock(88), incomingLoopStNoRingOff(89), outgoingTelcoDisconnect(90), outgoingEMWinkTimeout(91), outgoingEMWinkTooShort(92), outgoingNoChannelAvail(93), dspReboot(94), noDSPRespToKA(95), noDSPRespToDisc(96), dspTailPtrInvalid(97), dspHeadPtrInvalid(98), dataProcessingGenericErr(99), timeslotUnavailable(100), gmtTimeNotSet(101), chasAwarenessNotAvailable(102), r2InvalidChannelDirection(103), r2ChannelBlockedByNetwork(104), r2Glare(105), r2OutgoingCallBlocked(106), r2DNISNotFound(107), r2SigCauseCongestion(108), r2SigCauseUnallocNumber(109), r2DSPFatalError(110), callBlacklisted(111)

mdmCsInitialTxLinkRate		1.3.6.1.4.1.429.1.6.9.1.1.10
The transmit speed at which the modem initialy connected on it's last or current call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	bps110(1), bps300(2), bps600(3), bps1200(4), bps2400(5), bps4800(6), bps7200(7), bps9600(8), bps12K(9), bps14K(10), bps16K(11), bps19K(12), bps38K(13), bps75(14), bps450(15), unknown(16), bps57K(17), bps21K(18), bps24K(19), bps26K(20), bps28K(21), bps31K(23), bps33K(24), bps25333(25), bps26666(26), bps28000(27), bps29333(28), bps30666(29), bps32000(30), bps33333(31), bps34666(32), bps36000(33), bps37333(34), bps38666(35), bps40000(36), bps41333(37), bps42666(38), bps44000(39), bps45333(40), bps46666(41), bps48000(42), bps49333(43), bps50666(44), bps52000(45), bps53333(46), bps54666(47), bps56000(48), bps57333(49), bps58666(50), bps60000(51), bps61333(52), bps62666(53), bps64000(54)

mdmCsInitialRxLinkRate		1.3.6.1.4.1.429.1.6.9.1.1.11
The receive speed at which the modem initialy connected on it's previous or current call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	bps110(1), bps300(2), bps600(3), bps1200(4), bps2400(5), bps4800(6), bps7200(7), bps9600(8), bps12K(9), bps14K(10), bps16K(11), bps19K(12), bps38K(13), bps75(14), bps450(15), unknown(16), bps57K(17), bps21K(18), bps24K(19), bps26K(20), bps28K(21), bps31K(23), bps33K(24), bps25333(25), bps26666(26), bps28000(27), bps29333(28), bps30666(29), bps32000(30), bps33333(31), bps34666(32), bps36000(33), bps37333(34), bps38666(35), bps40000(36), bps41333(37), bps42666(38), bps44000(39), bps45333(40), bps46666(41), bps48000(42), bps49333(43), bps50666(44), bps52000(45), bps53333(46), bps54666(47), bps56000(48), bps57333(49), bps58666(50), bps60000(51), bps61333(52), bps62666(53), bps64000(54)

mdmCsFinalTxLinkRate		1.3.6.1.4.1.429.1.6.9.1.1.12
The current transmit link rate of a connection, or the last link rate of the last connection.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	bps110(1), bps300(2), bps600(3), bps1200(4), bps2400(5), bps4800(6), bps7200(7), bps9600(8), bps12K(9), bps14K(10), bps16K(11), bps19K(12), bps38K(13), bps75(14), bps450(15), unknown(16), bps57K(17), bps21K(18), bps24K(19), bps26K(20), bps28K(21), bps31K(23), bps33K(24), bps25333(25), bps26666(26), bps28000(27), bps29333(28), bps30666(29), bps32000(30), bps33333(31), bps34666(32), bps36000(33), bps37333(34), bps38666(35), bps40000(36), bps41333(37), bps42666(38), bps44000(39), bps45333(40), bps46666(41), bps48000(42), bps49333(43), bps50666(44), bps52000(45), bps53333(46), bps54666(47), bps56000(48), bps57333(49), bps58666(50), bps60000(51), bps61333(52), bps62666(53), bps64000(54)

mdmCsFinalRxLinkRate		1.3.6.1.4.1.429.1.6.9.1.1.13
The current receive link rate of a connection, or the last link rate of the last connection.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	bps110(1), bps300(2), bps600(3), bps1200(4), bps2400(5), bps4800(6), bps7200(7), bps9600(8), bps12K(9), bps14K(10), bps16K(11), bps19K(12), bps38K(13), bps75(14), bps450(15), unknown(16), bps57K(17), bps21K(18), bps24K(19), bps26K(20), bps28K(21), bps31K(23), bps33K(24), bps25333(25), bps26666(26), bps28000(27), bps29333(28), bps30666(29), bps32000(30), bps33333(31), bps34666(32), bps36000(33), bps37333(34), bps38666(35), bps40000(36), bps41333(37), bps42666(38), bps44000(39), bps45333(40), bps46666(41), bps48000(42), bps49333(43), bps50666(44), bps52000(45), bps53333(46), bps54666(47), bps56000(48), bps57333(49), bps58666(50), bps60000(51), bps61333(52), bps62666(53), bps64000(54)

mdmCsModulationType		1.3.6.1.4.1.429.1.6.9.1.1.14
Specifies the current/final modulation type of the current or last call. The value can be different from the object mdmCsInitModulationType only for X2/V.90 calls.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	usRoboticsHST(1), ccittV32(2), ccittV22bis(3), bell103(4), ccittV21(5), bell212(6), ccittV32bis(7), ccittV23(8), noConnection(9), bell208b(10), v21FaxClass1(11), v27FaxClass1(12), v29FaxClass1(13), v17FaxClass1(14), v21FaxClass2(15), v27FaxClass2(16), v29FaxClass2(17), v17FaxClass2(18), v32Terbo(19), v34(20), vFC(21), v34plus(22), x2server(23), v110(24), v120(25), x75(26), asyncSyncPPP(27), clearChannel(28), x2client(29), x2symmetric(30), piafs(31), x2version2(32), v90Analogue(33), v90Digital(34), v90AllDigital(35)

mdmCsSyncAsyncModeUsed		1.3.6.1.4.1.429.1.6.9.1.1.15
Defines whether the current or last call was synchronous or asynchronous.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	asynchronous(1), synchronous(2)

mdmCsErrorControlType		1.3.6.1.4.1.429.1.6.9.1.1.16
Specifies the Error control settings in the current or last call. (short form)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), mnpLevel3(2), mnpLevel4(3), ccittV42(4), usRoboticsHST(5), synchronousNone(6), mnpLevel2(7), mnp10(8), v42Etc(9), mnp10Ec(10), lapmEc(11), v42Etc2(12), ccittV42SREJ(13), piafs(14), v120(15), x75(16)

mdmCsCompressionType		1.3.6.1.4.1.429.1.6.9.1.1.17
Specifies the data compression used in the current or last call. (short format)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), ccittV42bis(2), mnpLevel5(3)

mdmCsEqualizationType		1.3.6.1.4.1.429.1.6.9.1.1.18
Specifies the equalization used in the current or last call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	long(1), short(2)

mdmCsFallbackEnabled		1.3.6.1.4.1.429.1.6.9.1.1.19
Specifies whether line speed fallbacks were negotiated on the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCsCharsSent		1.3.6.1.4.1.429.1.6.9.1.1.20
Specifies the number of characters sent on the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsCharsReceived		1.3.6.1.4.1.429.1.6.9.1.1.21
Specifies the number of characters received in the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsOctetsSent		1.3.6.1.4.1.429.1.6.9.1.1.22
Specifies the number of octets sent in the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsOctetsReceived		1.3.6.1.4.1.429.1.6.9.1.1.23
Specifies the number of octets received in the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsBlocksSent		1.3.6.1.4.1.429.1.6.9.1.1.24
Specifies the number of blocks sent in the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsBlocksReceived		1.3.6.1.4.1.429.1.6.9.1.1.25
Specifies the number of blocks received in the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsBlocksResent		1.3.6.1.4.1.429.1.6.9.1.1.26
Specifies the number of blocks the modem has had to retransmit due to block errors or timeouts in the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsRetrainsRequested		1.3.6.1.4.1.429.1.6.9.1.1.27
Specifies the number of retrains requested in the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsRetrainsGranted		1.3.6.1.4.1.429.1.6.9.1.1.28
Specifies the number of retrains granted in the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsLineReversalQty		1.3.6.1.4.1.429.1.6.9.1.1.29
Specifies the number of times the HST high and low speeds directions have been reversed in the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsCharsLost		1.3.6.1.4.1.429.1.6.9.1.1.30
Specifies the number of characters lost on the current or previous call. Not meaningful on synchronous calls.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsBackChannelRate		1.3.6.1.4.1.429.1.6.9.1.1.31
Specifies the negotiated HST back channel speed on the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	bps450(1), bps300(2), none(3)

mdmCsBlerQty		1.3.6.1.4.1.429.1.6.9.1.1.32
Specifies the number of block errors received on the link in the current or last call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsLinkTimeoutQty		1.3.6.1.4.1.429.1.6.9.1.1.33
Specifies the number of link protocol timeouts on the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsFallbackQty		1.3.6.1.4.1.429.1.6.9.1.1.34
Specifies the quantity of link speed fallbacks that occured on the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsUpshiftQty		1.3.6.1.4.1.429.1.6.9.1.1.35
Specifies the number of link speed upshifts have occured in the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsLinkNakQty		1.3.6.1.4.1.429.1.6.9.1.1.36
Specifies the quantity of negative acknowledgements sent in response to errored blocks received on the link in the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsGainHitCount		1.3.6.1.4.1.429.1.6.9.1.1.37
The modem calculates the gain that is required to adjust the received signal to the ideal level. This defines the number of times that the gain was recalculated durring the current or previous call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsSecurityUserName		1.3.6.1.4.1.429.1.6.9.1.1.38
The last dial security user that initiated the Call. This object is not saved to NVRAM.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..8)

mdmCsCallDuration		1.3.6.1.4.1.429.1.6.9.1.1.39
This is the length of the call in hh:mm:ss format. The maximum value reported will be 9999:59:59.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..10)

mdmCsCallRefNum		1.3.6.1.4.1.429.1.6.9.1.1.40
Call Reference Number
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsPriCardSlot		1.3.6.1.4.1.429.1.6.9.1.1.41
Primary Card Slot
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsTDMTimeSlot		1.3.6.1.4.1.429.1.6.9.1.1.42
Time Division Multipexing Time Slot
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsPriCardSpanLine		1.3.6.1.4.1.429.1.6.9.1.1.43
Primary Card Span Line
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsBChannelUsed		1.3.6.1.4.1.429.1.6.9.1.1.44
B Channel Used
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsQCarrFreqTx		1.3.6.1.4.1.429.1.6.9.1.1.45
Transmit carrier value (Hz).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

mdmCsQCarrFreqRx		1.3.6.1.4.1.429.1.6.9.1.1.46
Receive carrier value (Hz).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

mdmCsQSymRateTx		1.3.6.1.4.1.429.1.6.9.1.1.47
Transmit symbol rate.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

mdmCsQSymRateRx		1.3.6.1.4.1.429.1.6.9.1.1.48
Receive symbol rate.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

mdmCsQTrellisTx		1.3.6.1.4.1.429.1.6.9.1.1.49
Transmit Trellis coding.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	trellis8S-2D(1), trellis16S-4D(2), trellis32S-2D(3), trellis64S-4D(4)

mdmCsQTrellisRx		1.3.6.1.4.1.429.1.6.9.1.1.50
Receive Trellis coding.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	trellis8S-2D(1), trellis16S-4D(2), trellis32S-2D(3), trellis64S-4D(4)

mdmCsQNonLinCdTx		1.3.6.1.4.1.429.1.6.9.1.1.51
Status of transmit non-linear coding.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(1), on(2)

mdmCsQNonLinCdRx		1.3.6.1.4.1.429.1.6.9.1.1.52
Status of receive non-linear coding.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(1), on(2)

mdmCsQPrecodingTx		1.3.6.1.4.1.429.1.6.9.1.1.53
Status of transmit precoding.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(1), on(2)

mdmCsQPrecodingRx		1.3.6.1.4.1.429.1.6.9.1.1.54
Status of receive precoding.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(1), on(2)

mdmCsQShapingTx		1.3.6.1.4.1.429.1.6.9.1.1.55
Status of transmit shaping.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(1), on(2)

mdmCsQShapingRx		1.3.6.1.4.1.429.1.6.9.1.1.56
Status of receive shaping.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(1), on(2)

mdmCsQPreemphTx		1.3.6.1.4.1.429.1.6.9.1.1.57
Transmit pre-emphasis (-dBm).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

mdmCsQPreemphRx		1.3.6.1.4.1.429.1.6.9.1.1.58
Receive pre-emphasis (-dBm).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

mdmCsQRxLevel		1.3.6.1.4.1.429.1.6.9.1.1.59
Receive level (X 10) (-dBm).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsQTxLevel		1.3.6.1.4.1.429.1.6.9.1.1.60
Transmit level (X 10) (-dBm).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsQSNR		1.3.6.1.4.1.429.1.6.9.1.1.61
Signal to noise (x 10) (dB).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsQNearEcho		1.3.6.1.4.1.429.1.6.9.1.1.62
Near echo (x 10) (dB).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsQFarEcho		1.3.6.1.4.1.429.1.6.9.1.1.63
Far echo (x 10) (dB).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsQRndTripDly		1.3.6.1.4.1.429.1.6.9.1.1.64
Round trip delay (msec).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

mdmCsQPacketSizeCurr		1.3.6.1.4.1.429.1.6.9.1.1.65
Current packet size (bytes).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

mdmCsQPacketSizeLow		1.3.6.1.4.1.429.1.6.9.1.1.66
Min. packet size (bytes).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

mdmCsQPacketSizeHigh		1.3.6.1.4.1.429.1.6.9.1.1.67
Max. packet size (bytes).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

mdmCsQCellTxLevelCurr		1.3.6.1.4.1.429.1.6.9.1.1.68
Current Tx level cellular (x 10)(-dBm).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsQCellTxLevelLow		1.3.6.1.4.1.429.1.6.9.1.1.69
Min. Tx level cellular (x 10)(-dBm).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsQCellTxLevelHigh		1.3.6.1.4.1.429.1.6.9.1.1.70
Max. Tx level cellular (x 10)(-dBm).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsQSNRLevelCurr		1.3.6.1.4.1.429.1.6.9.1.1.71
Current SNR level cellular (x 10) (-dBm).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsQSNRLevelLow		1.3.6.1.4.1.429.1.6.9.1.1.72
Min. SNR level cellular (x 10) (-dBm).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsQSNRLevelHigh		1.3.6.1.4.1.429.1.6.9.1.1.73
Max. SNR level cellular (x 10) (-dBm).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsQCellularProt		1.3.6.1.4.1.429.1.6.9.1.1.74
Current cellular protocol.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), mnp10(2), mnp10ec(3), v42etc(4)

mdmCsFreqProbeData		1.3.6.1.4.1.429.1.6.9.1.1.75
Probe frequency.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..60)

mdmCsLevelProbeData		1.3.6.1.4.1.429.1.6.9.1.1.76
Probe level.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..30)

mdmCsQTimingOffset		1.3.6.1.4.1.429.1.6.9.1.1.77
Timing Offset in parts per million.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

mdmCsQCarrierOffset		1.3.6.1.4.1.429.1.6.9.1.1.78
Carrier Offset in Hertz.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

mdmCsQCoding		1.3.6.1.4.1.429.1.6.9.1.1.80
PCM Coding mu/A law Default=mulaw.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	mulaw(1), alaw(2)

mdmCsTrainingInfo		1.3.6.1.4.1.429.1.6.9.1.1.81
Training Information
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

mdmCsX2signature		1.3.6.1.4.1.429.1.6.9.1.1.82
X2 diagnostics information from modem in hex.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

mdmCsX2Status		1.3.6.1.4.1.429.1.6.9.1.1.83
x2 status of modem.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	x2v90NotOperational(1), x2Operational(2), v8DisabledLocal(3), x2DisabledLocal(4), baud3200DisabledLocal(5), speedLimitedLocal(6), v8notDetectedFromRemote(7), x2notDetectedFromRemote(8), incompatibleX2Versions(9), incompatibleX2Modes(10), baud3200DisabledRemote(11), excessiveHFAttenuation(12), channelNoSymbolRate(13), exitBeforeX2Connect(14), v90Operational(15), x2v90Operational(16), v90DisabledLocal(17), x2v90DisabledLocal(18), v90SymRatesDisabledLcl(19), v90NotDetectedFrmRemote(20), x2v90NotDetectedFrmRmt(21), incompatibleV90Versions(22), incompatibleV90Modes(23), v90IncompactibleSymRate(24)

mdmCsCallType		1.3.6.1.4.1.429.1.6.9.1.1.84
Call type information.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	analogCall(1), chT1WinkStart(2), chT1ImmediateStart(3), chT1LoopStart(4), chT1GroundStart(5), chT1PRICall(6)

mdmCsCallStartTime		1.3.6.1.4.1.429.1.6.9.1.1.85
Call started time in GMT format.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsCallEndTime		1.3.6.1.4.1.429.1.6.9.1.1.86
Call Ended time in GMT format.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCsDigitalPadAttenuated		1.3.6.1.4.1.429.1.6.9.1.1.87
Attenuation of the digital pad in tenths of DB.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

mdmCsInitModulationType		1.3.6.1.4.1.429.1.6.9.1.1.88
Specifies the modulation type of the current or last call. The value can be different from the object mdmCsModulationType only for X2/V.90 calls.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	usRoboticsHST(1), ccittV32(2), ccittV22bis(3), bell103(4), ccittV21(5), bell212(6), ccittV32bis(7), ccittV23(8), noConnection(9), bell208b(10), v21FaxClass1(11), v27FaxClass1(12), v29FaxClass1(13), v17FaxClass1(14), v21FaxClass2(15), v27FaxClass2(16), v29FaxClass2(17), v17FaxClass2(18), v32Terbo(19), v34(20), vFC(21), v34plus(22), x2server(23), v110(24), v120(25), x75(26), asyncSyncPPP(27), clearChannel(28), x2client(29), x2symmetric(30), piafs(31), x2version2(32), v90Analogue(33), v90Digital(34), v90AllDigital(35)

mdmCsRxMinSpeed		1.3.6.1.4.1.429.1.6.9.1.1.89
Current/Last Session MIN Rx Speed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	bps110(1), bps300(2), bps600(3), bps1200(4), bps2400(5), bps4800(6), bps7200(7), bps9600(8), bps12K(9), bps14K(10), bps16K(11), bps19K(12), bps38K(13), bps75(14), bps450(15), unknown(16), bps57K(17), bps21K(18), bps24K(19), bps26K(20), bps28K(21), bps31K(23), bps33K(24), bps25333(25), bps26666(26), bps28000(27), bps29333(28), bps30666(29), bps32000(30), bps33333(31), bps34666(32), bps36000(33), bps37333(34), bps38666(35), bps40000(36), bps41333(37), bps42666(38), bps44000(39), bps45333(40), bps46666(41), bps48000(42), bps49333(43), bps50666(44), bps52000(45), bps53333(46), bps54666(47), bps56000(48), bps57333(49), bps58666(50), bps60000(51), bps61333(52), bps62666(53), bps64000(54)

mdmCsRxMaxSpeed		1.3.6.1.4.1.429.1.6.9.1.1.90
Current/Last Session MAX Rx Speed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	bps110(1), bps300(2), bps600(3), bps1200(4), bps2400(5), bps4800(6), bps7200(7), bps9600(8), bps12K(9), bps14K(10), bps16K(11), bps19K(12), bps38K(13), bps75(14), bps450(15), unknown(16), bps57K(17), bps21K(18), bps24K(19), bps26K(20), bps28K(21), bps31K(23), bps33K(24), bps25333(25), bps26666(26), bps28000(27), bps29333(28), bps30666(29), bps32000(30), bps33333(31), bps34666(32), bps36000(33), bps37333(34), bps38666(35), bps40000(36), bps41333(37), bps42666(38), bps44000(39), bps45333(40), bps46666(41), bps48000(42), bps49333(43), bps50666(44), bps52000(45), bps53333(46), bps54666(47), bps56000(48), bps57333(49), bps58666(50), bps60000(51), bps61333(52), bps62666(53), bps64000(54)

mdmCsTxMinSpeed		1.3.6.1.4.1.429.1.6.9.1.1.91
Current/Last Session MIN Tx Speed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	bps110(1), bps300(2), bps600(3), bps1200(4), bps2400(5), bps4800(6), bps7200(7), bps9600(8), bps12K(9), bps14K(10), bps16K(11), bps19K(12), bps38K(13), bps75(14), bps450(15), unknown(16), bps57K(17), bps21K(18), bps24K(19), bps26K(20), bps28K(21), bps31K(23), bps33K(24), bps25333(25), bps26666(26), bps28000(27), bps29333(28), bps30666(29), bps32000(30), bps33333(31), bps34666(32), bps36000(33), bps37333(34), bps38666(35), bps40000(36), bps41333(37), bps42666(38), bps44000(39), bps45333(40), bps46666(41), bps48000(42), bps49333(43), bps50666(44), bps52000(45), bps53333(46), bps54666(47), bps56000(48), bps57333(49), bps58666(50), bps60000(51), bps61333(52), bps62666(53), bps64000(54)

mdmCsTxMaxSpeed		1.3.6.1.4.1.429.1.6.9.1.1.92
Current/Last Session MAX Tx Speed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	bps110(1), bps300(2), bps600(3), bps1200(4), bps2400(5), bps4800(6), bps7200(7), bps9600(8), bps12K(9), bps14K(10), bps16K(11), bps19K(12), bps38K(13), bps75(14), bps450(15), unknown(16), bps57K(17), bps21K(18), bps24K(19), bps26K(20), bps28K(21), bps31K(23), bps33K(24), bps25333(25), bps26666(26), bps28000(27), bps29333(28), bps30666(29), bps32000(30), bps33333(31), bps34666(32), bps36000(33), bps37333(34), bps38666(35), bps40000(36), bps41333(37), bps42666(38), bps44000(39), bps45333(40), bps46666(41), bps48000(42), bps49333(43), bps50666(44), bps52000(45), bps53333(46), bps54666(47), bps56000(48), bps57333(49), bps58666(50), bps60000(51), bps61333(52), bps62666(53), bps64000(54)

mdmCsCollectedDTMFDigits		1.3.6.1.4.1.429.1.6.9.1.1.93
This object is an ASCII array of the DTMF digits collected from the client.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..64)

mdmEv		1.3.6.1.4.1.429.1.6.10
OBJECT IDENTIFIER

mdmEvTable		1.3.6.1.4.1.429.1.6.10.1
A list of modem events.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmEvEntry

mdmEvEntry		1.3.6.1.4.1.429.1.6.10.1.1
Modem events that can be managed.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmEvEntry

mdmEvIndex		1.3.6.1.4.1.429.1.6.10.1.1.1
Index into event table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmEvWatchdogTimouts		1.3.6.1.4.1.429.1.6.10.1.1.2
Quantity of times that a watchdog timeout has been detected for this modem.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvDteIdleTimouts		1.3.6.1.4.1.429.1.6.10.1.1.3
The number of times that the modem has had no DTE activity for the time specified by mdmEtDteIdleThresh.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvInConnectEstabs		1.3.6.1.4.1.429.1.6.10.1.1.4
The number of times that the modem has reported a incomming connection established event.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvOutConnectEstabs		1.3.6.1.4.1.429.1.6.10.1.1.5
The number of times that the modem has reported an outgoing connection established event.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvInConnectTerms		1.3.6.1.4.1.429.1.6.10.1.1.6
The number of times the modem has reported an incomming connection terminated event.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvOutConnectTerms		1.3.6.1.4.1.429.1.6.10.1.1.7
The number of times the modem has reported an outgoing connection termination event.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvConnectAttemptFails		1.3.6.1.4.1.429.1.6.10.1.1.8
The number of times the modem has reported a connect attempt failure event. This does not include those connect attempt failures that are reported due to no dial tone and no loop current.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvConnectTimouts		1.3.6.1.4.1.429.1.6.10.1.1.9
The number of times that the NMC has detected a call that has has a duration in excess of the threshold defined in mdmEtConnectThresh.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvMgmtBusFailures		1.3.6.1.4.1.429.1.6.10.1.1.10
The number of times the NMC has been unable to get a response from the modem to requests on the management bus.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvResetByDtes		1.3.6.1.4.1.429.1.6.10.1.1.11
The number of times that the modem has been reset by the DTE via the ATZ command or by DTR drop.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvDtrFalses		1.3.6.1.4.1.429.1.6.10.1.1.12
The number of times the modem has reported DTR False events. The DTR false event timeout is based on mdmEtDtrFalseThresh.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvDtrTrues		1.3.6.1.4.1.429.1.6.10.1.1.13
The number of times the modem has reported DTR True events. The modem reports these events to the NMC based on the value of mdmEtDtrTrueTresh.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvNoTones		1.3.6.1.4.1.429.1.6.10.1.1.14
The number of times the modem reported no tones.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvNoLoops		1.3.6.1.4.1.429.1.6.10.1.1.15
The number of times the modem reported no loop current events.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvBlers		1.3.6.1.4.1.429.1.6.10.1.1.16
The number of times the modem reported BLERs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvFallBacks		1.3.6.1.4.1.429.1.6.10.1.1.17
The number of times the modem reported fall backs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvInConnectTime		1.3.6.1.4.1.429.1.6.10.1.1.18
Cumulative counter for inbound call connect time.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvInTotalBytesRx		1.3.6.1.4.1.429.1.6.10.1.1.19
Cumulative counter for number of bytes received on inbound calls.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvInTotalBytesTx		1.3.6.1.4.1.429.1.6.10.1.1.20
Cumulative counter for number of bytes transmitted on inbound calls.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvOutConnectTime		1.3.6.1.4.1.429.1.6.10.1.1.21
Cumulative counter for outbound call connect time.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvOutTotalBytesRx		1.3.6.1.4.1.429.1.6.10.1.1.22
Cumulative counter for number of bytes received on outbound calls.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvOutTotalBytesTx		1.3.6.1.4.1.429.1.6.10.1.1.23
Cumulative counter for number of bytes transmitted on outbound calls.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvInConnAttemptFails		1.3.6.1.4.1.429.1.6.10.1.1.24
The number of times the modem has reported a inbound connect attempt failure event. This does not include those connect attempt failues that are reported due to no dial time and no loop current.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEvOutConnAttemptFails		1.3.6.1.4.1.429.1.6.10.1.1.25
The number of times the modem has reported a outbound connect attempt failure event. This does not include those connect attempt failures that are reported due to no dial tone and no loop current.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

mdmEt		1.3.6.1.4.1.429.1.6.11
OBJECT IDENTIFIER

mdmEtTable		1.3.6.1.4.1.429.1.6.11.1
Table of event thresholds used for setting up the modem to report events that can in turn be monitored by RMON.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmEtEntry

mdmEtEntry		1.3.6.1.4.1.429.1.6.11.1.1
Event Thresholds that are used by the modem and the NMC to qualify certain events.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmEtEntry

mdmEtIndex		1.3.6.1.4.1.429.1.6.11.1.1.1
Index into table used to identify the the specific modem, contians the unique value from the chassis mib entity table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmEtDteIdleThresh		1.3.6.1.4.1.429.1.6.11.1.1.2
Defines the length of time for the modem to wait before reporting a 'DTE transmit data idle' event. (There must be no activity on the DTE transmit line for the specified quantity of minutes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmEtDtrFalseThresh		1.3.6.1.4.1.429.1.6.11.1.1.3
Defines the quantity of seconds that will be used by the modem to qualify a 'DTR False' event.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmEtDtrTrueThresh		1.3.6.1.4.1.429.1.6.11.1.1.4
Defines the quantity of seconds that the modem will use to qualify a 'DTR True' event.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmEtConnTimeLimit		1.3.6.1.4.1.429.1.6.11.1.1.5
Defines the number of minutes that a call may be connected before triggering the 'connect timer limit' event. A value of zero for this limit means that no event is to be detected (ie. no time limit).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmEtBlerThresh		1.3.6.1.4.1.429.1.6.11.1.1.6
Defines the number of BLERs that will be used to qualify the 'BLER count at threshold' event for a given call.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmEtFallbackThresh		1.3.6.1.4.1.429.1.6.11.1.1.7
Defines the number of fallbacks at which the 'fallback count at threshold' event will be generated for a given call.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmCd		1.3.6.1.4.1.429.1.6.12
OBJECT IDENTIFIER

mdmCdTable		1.3.6.1.4.1.429.1.6.12.1
The command table contains an entry for each modem installed in a chassis. It provides a means for processing actions requested by the management console. The mechanism used is to set the command and get the result which will indicate the success of the request.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmCdEntry

mdmCdEntry		1.3.6.1.4.1.429.1.6.12.1.1
Objects that are used to request that certain actions be taken by the modem itself or that the NMC take certain actions for the modem.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmCdEntry

mdmCdIndex		1.3.6.1.4.1.429.1.6.12.1.1.1
The index value which uniquely identifies the modem to which this entry is applicable. The value corresponds to the index of the corresponding modem in the entity table of the chassis MIB.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCdMgtStationId		1.3.6.1.4.1.429.1.6.12.1.1.2
This object is a generic read-write variable that a Management Station (MS) can use to guarantee that the results from a given command are the results of a command issued by that specific MS. Each MS must SET a unique value to this object when doing commands and GET the value of this object together with uchasCmdReqId and uchasCmdResult to detect interference from other MSs.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..8)

mdmCdReqId		1.3.6.1.4.1.429.1.6.12.1.1.3
This object contains the value of the request-id field in the SNMP PDU which invoked the most recent command or test on this modem. If the request-id is unknown or undefined, this object contains the value zero.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

mdmCdFunction		1.3.6.1.4.1.429.1.6.12.1.1.4
This object contains a value that describes the command that is being invoked.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noCommand(1), softwareReset(2), storeToNvram(3), restoreFromDflt(4), restoreFromNvram(5), offHook(6), onHook(7), sndTone(8), rcvTone(9), endTest(10), rspndrTest105(11), rspndrTest102(12), lclAnlgLpbk(13), lclDgtlLpbk(14), rmtDgtlLpbk(15), selfTest(16), testRam(17), testRom(18), testNVRAM(19), v54LclAnlgLpbk(20), v54RmtDgtlLpbk(21), idlePhoneLine(22), loadHwFlowDflt(23), loadSwFlowDflt(24), loadMnp10CllulrDflt(25), loadV42CllulrMblDflt(26), loadV42CllulrFxdDflt(27), hardBusyAtDisable(33), softBusyAtDisable(34), restoreLineAt(35)

mdmCdForce		1.3.6.1.4.1.429.1.6.12.1.1.5
In certain cases the modem may be in a state where certain commands could adversely affect connectiuons. In such cases, a command request with this object not present or set to noForce will result in a warning. If the operator elects to ignore such warnings, this object can be set to force in a subsequent request to cause the command to be carried out regardless of the potetialy hazzerdous effect.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	force(1), noForce(2)

mdmCdParam		1.3.6.1.4.1.429.1.6.12.1.1.6
This object can contain parameters that are specific to the particualar command being issued.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..24)

mdmCdResult		1.3.6.1.4.1.429.1.6.12.1.1.7
This object contains the result of the most recently requested command or test, or the value none(1) if no commands have been requested since last reset.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), success(2), inProgress(3), notSupported(4), unAbleToRun(5), aborted(6), failed(7)

mdmCdCode		1.3.6.1.4.1.429.1.6.12.1.1.8
The value of this object indicates a further description of what went wrong when a command fails.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noError(1), unable(2), unrecognizedCommand(6), slotEmpty(8), noResponse(12), notConnected(13), connected(14), onLine(17), unsupportedCommand(20), deviceDisabled(22), deviceInTestMode(24), testFailed(25), deviceInSecurityMode(31), noRTS(51), noDTR(52), wrongLoopbackSpeed(53), noLoopbackInARQ(54), pendingSoftwareDownload(73), invalidFrequency(89), noLoopCurrent(90), noDialTone(91), noLineDetected(92)

mdmTe		1.3.6.1.4.1.429.1.6.13
OBJECT IDENTIFIER

mdmTeTable		1.3.6.1.4.1.429.1.6.13.1
A table containing an enable for each trap that a modem entity is capable of generating. Some of these events occur often and traps may flood the network if care is not taken to avoid such conditions. These traps should be enabled sparingly. (usually only when debugging a problem on a particular modem)
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmTeEntry

mdmTeEntry		1.3.6.1.4.1.429.1.6.13.1.1
There is one modem trap enable row for each modem entity in the NAS chassis.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmTeEntry

mdmTeIndex		1.3.6.1.4.1.429.1.6.13.1.1.1
A unique index which identifies the modem for which these trap enables pertain. The index to the trap enable table matches the index of the corresponding modem in the entity table in the chassis MIB.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmTeInConnEstablished		1.3.6.1.4.1.429.1.6.13.1.1.2
Enables generation of an SNMP trap upon detection of an incoming connection establishment on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeOutConnEstablished		1.3.6.1.4.1.429.1.6.13.1.1.3
Enables generation of an SNMP trap upon detection of an outgoing connection establishment on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeInConnTerminated		1.3.6.1.4.1.429.1.6.13.1.1.4
Enables generation of an SNMP trap upon detection of an incoming connection termination on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeOutConnTerminated		1.3.6.1.4.1.429.1.6.13.1.1.5
Enables generation of an SNMP trap upon detection of an outgoing connection terminated on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeConnAttemptFailure		1.3.6.1.4.1.429.1.6.13.1.1.6
Enables generation of an SNMP trap upon detection of a connection attemp failure on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeConnLimitExpired		1.3.6.1.4.1.429.1.6.13.1.1.7
Enables generation of an SNMP trap upon detection of the expiration of the connection time limit on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeDteXmitDataIdle		1.3.6.1.4.1.429.1.6.13.1.1.8
Enables generation of an SNMP trap upon detection of DTE transmit data idle on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeDtrTrue		1.3.6.1.4.1.429.1.6.13.1.1.9
Enables generation of an SNMP trap upon detection of DTR going true on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeDtrFalse		1.3.6.1.4.1.429.1.6.13.1.1.10
Enables generation of an SNMP trap upon detection of DTR going false on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeBlerCountAtThresh		1.3.6.1.4.1.429.1.6.13.1.1.11
Enables generation of an SNMP trap upon detection of the BLER count at the specified threshold on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeFallbkCountAtThresh		1.3.6.1.4.1.429.1.6.13.1.1.12
Enables generation of an SNMP trap upon detection of the fallback count at the specified threshold on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeNoDialTone		1.3.6.1.4.1.429.1.6.13.1.1.13
Enables generation of an SNMP trap upon detection of no dial tone on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeNoLoopCurrent		1.3.6.1.4.1.429.1.6.13.1.1.14
Enables generation of an SNMP trap upon detection of no loop current on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeResetByDTE		1.3.6.1.4.1.429.1.6.13.1.1.15
Enables generation of an SNMP trap upon detection of reset by DTE on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeDialOutCallDur		1.3.6.1.4.1.429.1.6.13.1.1.16
Enables the dial out (from the NMC) call duration trap. Default = disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeDialInCallDur		1.3.6.1.4.1.429.1.6.13.1.1.17
Enables the dial in (to the NMC) call duration trap. Default = disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTePbActive		1.3.6.1.4.1.429.1.6.13.1.1.18
Enables the Packet Bus Active. Default = disable(2).
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTePbLost		1.3.6.1.4.1.429.1.6.13.1.1.19
Enables the Packet Bus Lost trap. Default = disable(2).
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeDteRingNoAns		1.3.6.1.4.1.429.1.6.13.1.1.20
Enables the Dte Ring No Answer trap. Default = disable(2).
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTePbClockLossEvent		1.3.6.1.4.1.429.1.6.13.1.1.21
This object is used to disable the ability for a NAC to report when the packet bus clock has been lost. Default = disableAll(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTePbClockRestoreEvent		1.3.6.1.4.1.429.1.6.13.1.1.22
This object is used to disable the ability for a NAC to report when the packet bus clock has been restored. Default = disableAll(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeInConnAttemptFail		1.3.6.1.4.1.429.1.6.13.1.1.23
Enables generation of a SNMP trap upon detection of an inbound connection attempt failure on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTeOutConnAttemptFail		1.3.6.1.4.1.429.1.6.13.1.1.24
Enables generation of a SNMP trap upon detection of an outbound connection attempt failure on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmTe105ResponderTest		1.3.6.1.4.1.429.1.6.13.1.1.25
Enables generation of a SNMP trap upon detection of a 105 responder test on the specified modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

mdmLs		1.3.6.1.4.1.429.1.6.14
OBJECT IDENTIFIER

mdmLsTable		1.3.6.1.4.1.429.1.6.14.1
A table defining all the Link Security parameters for each modem in the chassis.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmLsTableEntry

mdmLsTableEntry		1.3.6.1.4.1.429.1.6.14.1.1
Link Security parameters for a modem. These define the link level security operations which take place when a call is negotiated.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmLsTableEntry

mdmLsIndex		1.3.6.1.4.1.429.1.6.14.1.1.1
The index which uniquely identifies the modem to which this entry is applicable. The value corresponds to the value of the index to the entity table in the chassis MIB that corresponds to the same modem.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmLsSecurityEnable		1.3.6.1.4.1.429.1.6.14.1.1.2
Allows to disable/enable the dial security feature for the modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmLsFallbackPromptEnable		1.3.6.1.4.1.429.1.6.14.1.1.3
Disables/enables the prompting by the called modem when the auto pass password supplied by the caller fails or if no password is supplied at all.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmLsForcePromptEnable		1.3.6.1.4.1.429.1.6.14.1.1.4
If this is enabled, the modem will prompt the remote user for a password regardless of the success of the modem to negotiate the auto pass password.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmLsLocAccPasswdEnable		1.3.6.1.4.1.429.1.6.14.1.1.5
Disables/enables the Local Access Password feature used to establish security check when accessing any security setting.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmLsDialBackEnable		1.3.6.1.4.1.429.1.6.14.1.1.6
If this is set to enable the modem, after successful password validation, will disconnect and dial out to the originating modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmLsAutoPassPasswd		1.3.6.1.4.1.429.1.6.14.1.1.7
Contains the Auto Pass Password used for establishing Link security during call negotiation.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..8)

mdmLsLocalAccessPasswd		1.3.6.1.4.1.429.1.6.14.1.1.8
Contains the Local Access password used when accessing any security setting and when Local Access password feature is enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..8)

mdmLsAccountPasswd		1.3.6.1.4.1.429.1.6.14.1.1.9
Contains the fall back password which must be entered if auto pass password is not satisfied.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..8)

mdmHs		1.3.6.1.4.1.429.1.6.15
OBJECT IDENTIFIER

mdmHsTable		1.3.6.1.4.1.429.1.6.15.1
A table containing the Hub security parameters accessible in the modem.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmHsEntry

mdmHsEntry		1.3.6.1.4.1.429.1.6.15.1.1
There is one entry in this table for each modem entity found in the chassis mib entity table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	MdmHsEntry

mdmHsIndex		1.3.6.1.4.1.429.1.6.15.1.1.1
An index that uniquely identifies the modem to which this row in the Hub Security table pertains. The value of this index matches the value of the index for the corresonding entity in the entity table of the Chassis MIB.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmHsDialInEnable		1.3.6.1.4.1.429.1.6.15.1.1.2
Allows the modem to be configured for dial-in security. Enabling this effectively disables the modem's built-in Link security operation. The default for this object is disabled.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), allowNoNMC(2), refuseNoNMC(3), busyOutNoNMC(4)

mdmHsDialOutEnable		1.3.6.1.4.1.429.1.6.15.1.1.3
Allows modems to be configured for dial-out security. Enabling this effectively disables the modem's built-in link security operation. The default value for this object is disabled.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), refuseNoNMC(2), allowNoNMC(3)

mdmHsDtrDcdDelay		1.3.6.1.4.1.429.1.6.15.1.1.4
Allows configuration of the time delay (in 100ths of a second) between reciept of DTR and assertion of DCD when the user on an incomming security call has successfully compleated the security dialog. This object only applies to modems using an RS232 like interface.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmHsDtrDsrDelay		1.3.6.1.4.1.429.1.6.15.1.1.5
Allows configuration of the delay (in 100ths of a second) between detection of DTR and assertion of DSR when an incomming security call has completed security negotiation successfully.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

mdmAutoResponse		1.3.6.1.4.1.429.1.6.16
OBJECT IDENTIFIER

mdmArTable		1.3.6.1.4.1.429.1.6.16.1
Table of auto response scripts for each modem in the chassis. The number of table entries is specified by modemNumber.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmArEntry

mdmArEntry		1.3.6.1.4.1.429.1.6.16.1.1
List of configurable auto response scripts.
Status: optional	Access: not-accessible
OBJECT-TYPE
	MdmArEntry

mdmArIndex		1.3.6.1.4.1.429.1.6.16.1.1.1
Index in to the auto response table. This index contains the unique value associated with the modem as defined in the chassis mib entity table.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

mdmArIncomConnectEstab		1.3.6.1.4.1.429.1.6.16.1.1.2
This script is triggered when a Total Control WAN HUB modem establishes a connection with a remote modem. The remote modem is the caller.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArOutgoConnectEstab		1.3.6.1.4.1.429.1.6.16.1.1.3
This script is triggered when a Total Control WAN HUB modem establishes a connection with a remote modem. The Total Control WAN HUB modem is the caller.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArIncomConnectTerm		1.3.6.1.4.1.429.1.6.16.1.1.4
This script is triggered after a remote modem has called a Total Control WAN HUB modem, but the connection between them terminated for some reason.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArOutgoConnectTerm		1.3.6.1.4.1.429.1.6.16.1.1.5
This script is triggered after a Total Control WAN HUB modem called a remote modem, but the connection between them terminated for some reason.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArConnectAttemptFail		1.3.6.1.4.1.429.1.6.16.1.1.6
This script is triggered when a Total Control WAN HUB modem fails to connect with a remote modem for an incoming or an outgoing call.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArConnectTimeExpire		1.3.6.1.4.1.429.1.6.16.1.1.7
This script is triggered when a connection duration exceeds the user defined connection time limit.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArResetByDte		1.3.6.1.4.1.429.1.6.16.1.1.8
This script is triggered when a modem has been reset by a DTE.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArDteXmitIdle		1.3.6.1.4.1.429.1.6.16.1.1.9
This script is triggered when a modem's DTE remains idle for specified amount of minutes that is defined by a user.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArBlersAtThresh		1.3.6.1.4.1.429.1.6.16.1.1.10
This script is triggered when a Total Control WAN HUB modem receives a certain amount of block errors. This amount can be configured by a user.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArFbacksAtThresh		1.3.6.1.4.1.429.1.6.16.1.1.11
This script is triggered when a Total Control WAN HUB modem reaches a certain amount of fall backs within a single session. This amount can be configured by a user.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArDialOutLoginFail		1.3.6.1.4.1.429.1.6.16.1.1.12
This script is triggered when a user, who is attempting to dial out from a Total Control WAN HUB modem that supports dial security, enters an invalid response to a prompt.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArDialOutRestrNum		1.3.6.1.4.1.429.1.6.16.1.1.13
This script is triggered when a user, who is attempting to dial out from a Total Control WAN HUB modem that supports dial security, uses a restricted number.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArDialInLoginFail		1.3.6.1.4.1.429.1.6.16.1.1.14
This script is triggered when a user, who is attempting to dial in from a remote modem in to a Total Control WAN HUB modem that supports dial security, enters an invalid response to a prompt.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArDialBackRestrNum		1.3.6.1.4.1.429.1.6.16.1.1.15
This script is triggered when a user, who is attempting to dial in from a remote modem in to a Total Control WAN HUB modem that supports dial security, requests the Total Control WAN HUB modem to dial back to a restricted number.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArDialBackRestModem		1.3.6.1.4.1.429.1.6.16.1.1.16
This script is triggered when a user, who is attempting to dial in from a remote modem in to a Total Control WAN HUB modem that supports dial security, requests the Total Control WAN HUB modem to dial back using a restricted Total Control WAN HUB modem.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArLoginAttemptsExceed		1.3.6.1.4.1.429.1.6.16.1.1.17
This script is triggered when a user, who is dialing in to or out of the Total Control WAN HUB modem, exceeds the number of correct user name/password response attempts.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArUserBlacklisted		1.3.6.1.4.1.429.1.6.16.1.1.18
This script is triggered when a user, who is dialing in to or out of the Total Control WAN HUB modem, exceeds the number of password prompt retries. At this point the user becomes black listed.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArAttmpLoginByBlistUsr		1.3.6.1.4.1.429.1.6.16.1.1.19
This script is triggered when a user, who has been black listed, is trying to dial in to or out of a Total Control WAN HUB modem.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArRspAttemptLimExceed		1.3.6.1.4.1.429.1.6.16.1.1.20
This script is triggered when a user, who is dialing in to or out of a Total Control WAN HUB modem, exceeds the number of security prompt retries during a single dial security session.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArWatchdog		1.3.6.1.4.1.429.1.6.16.1.1.21
This script is triggered when a software failure has occurred on a modem.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArMgtBusFailure		1.3.6.1.4.1.429.1.6.16.1.1.22
This script is triggered when a contact with a modem, via the management bus, has been lost.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArDtrTrue		1.3.6.1.4.1.429.1.6.16.1.1.23
This script is triggered when a modem's DTE transitions it DTR line from low to high and holds it high for the specified number of seconds. This amount is user configurable.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArDtrFalse		1.3.6.1.4.1.429.1.6.16.1.1.24
This script is triggered when a modem's DTE transitions it DTR line from high to low and holds it low for the specified number of seconds. This amount is user configurable.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArMdmRingNoAnswer		1.3.6.1.4.1.429.1.6.16.1.1.25
This script is triggered when a Total Control WAN HUB modem, configured for auto answer, fails to answer an incoming call within a specified number of rings. This amount is user configurable.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArDteRingNoAnswer		1.3.6.1.4.1.429.1.6.16.1.1.26
This script is triggered when a DTE fials to raise DTR in response to an incoming call for a specified amount of rings. This amount is user configurable.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArNoDialTone		1.3.6.1.4.1.429.1.6.16.1.1.27
This script is triggered when a Total Control WAN HUB modem goes off hook, but detects an inadequate dial tone level on an analog phone line.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArNoLoopCurrent		1.3.6.1.4.1.429.1.6.16.1.1.28
This script is triggered when a Total Control WAN HUB modem goes off hook, but it does not detect the presence of loop current on an analog phone line.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArTimer1		1.3.6.1.4.1.429.1.6.16.1.1.29
This script is triggered when the first general purpose timer expires.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArTimer2		1.3.6.1.4.1.429.1.6.16.1.1.30
This script is triggered when the second general purpose timer expires.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArTimer3		1.3.6.1.4.1.429.1.6.16.1.1.31
This script is triggered when the third general purpose timer expires.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArTimer4		1.3.6.1.4.1.429.1.6.16.1.1.32
This script is triggered when the fourth general purpose timer expires.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArPacketBusActive		1.3.6.1.4.1.429.1.6.16.1.1.33
This script is triggered when a packet bus active event is detected by the modem.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmArPacketBusLost		1.3.6.1.4.1.429.1.6.16.1.1.34
This script is triggered when a packet bus lost event is detected by the modem.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..40)

mdmCe		1.3.6.1.4.1.429.1.6.17
OBJECT IDENTIFIER

mdmCeTable		1.3.6.1.4.1.429.1.6.17.1
A list of configurable Cellular Support object for a modem. The number of table entries is given by modemNumber.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmCeEntry

mdmCeEntry		1.3.6.1.4.1.429.1.6.17.1.1
Objects which define the Cellular characteristics for a particular modem.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmCeEntry

mdmCeIndex		1.3.6.1.4.1.429.1.6.17.1.1.1
This index value which uniquely identifies the modem to which this entry is applicable. The value corresponds to the index of the corresponding modem in the entity table of the chassis MIB.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmCeMnp10Dis		1.3.6.1.4.1.429.1.6.17.1.1.2
This object is bit 0 of S-register 60. It disable/enables MNP10 negotiation mostly used with cellular operations. (defualt=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCeMnpxDis		1.3.6.1.4.1.429.1.6.17.1.1.3
This object is bit 1 of S-register 60. It will enable/disable the MNP extended services to be active during negotiation. This will mean that MNP10 will use V.42 to negotiate. (defualt=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCeComp		1.3.6.1.4.1.429.1.6.17.1.1.4
This object is bit 2 of S-register 60. It selects which compression type will be negotiated if allowed by other modem settings. (default =0>
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	mnp5(1), v42bis(2)

mdmCeOperDis		1.3.6.1.4.1.429.1.6.17.1.1.5
This object is bit 3 of S-register 60. It announces that at least one end of the link will be across a cellular network. Therefore, the Dyncamic Transmit Algorithm will be active. (default=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCeLinkSpeed		1.3.6.1.4.1.429.1.6.17.1.1.6
This object is bit 4 of register 60 tells the modem which speed to establish the link at. (default=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	linkAtHighSpeed(1), linkAt1200BpsV22(2)

mdmCeShortFormRules		1.3.6.1.4.1.429.1.6.17.1.1.7
This object is the S-register 61. It takes a value from 0 to 3 and regulates the V.42bis Short Form Negotiation rules. The short form assumes that the maximum string length is always 32 octets and that the direction of compression is always bi-directional. (default=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), form1CodeWords512(2), form2CodeWords1024(3), form3CodeWords2048(4)

mdmCeDceBitraLim		1.3.6.1.4.1.429.1.6.17.1.1.8
This object is the S-register 64. It limits DCE bitrates to values equal to or below the chosen setting. (default=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	maxDceRate(1), bps4800(2), bps7200(3), bps9600(4), bps12000(5), bps14400(6)

mdmCeDceTxLev		1.3.6.1.4.1.429.1.6.17.1.1.9
This object is S-register 65. It selects DCE TX level to use during cellular operations. (default=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	modemContrlTxLev(1), dBm10(2), dBm11(3), dBm12(4), dBm13(5), dBm14(6), dBm15(7), dBm16(8), dBm17(9), dBm18(10), dBm19(11), dBm20(12), dBm21(13), dBm22(14), dBm23(15), dBm24(16), dBm25(17)

mdmCeV42EtcDis		1.3.6.1.4.1.429.1.6.17.1.1.10
This object is the bit 0 of S-register 66. It enables/disables ETC. (default=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCeV42CellSite		1.3.6.1.4.1.429.1.6.17.1.1.11
This object is the bit 1 of S-register 66. It selects fixed or mobile site operations. (default=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	fixedSite(1), mobileSite(2)

mdmCeV42EtcCallToneDis		1.3.6.1.4.1.429.1.6.17.1.1.12
This object is the bit 2 of S-register 66. It enables/disables ETC calling tone. (default=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCeV42EtcTxLevConDis		1.3.6.1.4.1.429.1.6.17.1.1.13
This object is the bit 3 of S-register 66. It enables/disables forced ETC TX level control. (default=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCeDceStartRate		1.3.6.1.4.1.429.1.6.17.1.1.14
This object is the bits 4 and 5 of S-register 66. It sets the DCE startup rate. (default=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), bps4800(2), bps9600(3)

mdmCeV42DceTxDemDis		1.3.6.1.4.1.429.1.6.17.1.1.15
This object is the bit 6 of S-register 66. It enables/disables DCE TX De-emphasis. (default=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCeMnp10FallbackDis		1.3.6.1.4.1.429.1.6.17.1.1.16
This object is the bit 5 of S-register 60. It enables/disables MNP10 fallback. (default=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCeMnp10FallforDis		1.3.6.1.4.1.429.1.6.17.1.1.17
This object is the bit 6 of S-register 60. It enables/disables MNP10 fallforward. (default=0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCeDbNoEtcDis		1.3.6.1.4.1.429.1.6.17.1.1.18
This object is the bit 7 of S-register 66. It enables/disables non-ETC originate mode. (default=0/disable)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdmCeMnpxDetPhEna		1.3.6.1.4.1.429.1.6.17.1.1.19
This object is the bit 7 of S-register 60. It enables/disables the MNPX detection phase during connection establishment. (default=0/enable).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mdmSts		1.3.6.1.4.1.429.1.6.18
OBJECT IDENTIFIER

mdmStsTable		1.3.6.1.4.1.429.1.6.18.1
A table containing configuration information for each NAC in the NAS chassis that supports packet bus datagrams.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmStsEntry

mdmStsEntry		1.3.6.1.4.1.429.1.6.18.1.1
There is one configuration row for each modem entity.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmStsEntry

mdmStsIndex		1.3.6.1.4.1.429.1.6.18.1.1.1
A unique value for each card in the chassis. The value of this object matches the value of the index of the corresponding card's entry in the entity table of the chassis MIB.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmStsPbClock		1.3.6.1.4.1.429.1.6.18.1.1.2
This object defines the current status of the packet bus clock.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notSupported(1), clockMaster(2), clockSlave(3), noClockPresent(4)

mdmMa		1.3.6.1.4.1.429.1.6.19
OBJECT IDENTIFIER

mdmMaTable		1.3.6.1.4.1.429.1.6.19.1
A Mapping table entry, containing objects which define the card level configuration each modem is mapped to and the unique change indicator.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdmMaEntry

mdmMaEntry		1.3.6.1.4.1.429.1.6.19.1.1
Objects which define the Mapping and Status for a particular modem.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MdmMaEntry

mdmMaIndex		1.3.6.1.4.1.429.1.6.19.1.1.1
This index value which uniquely identifies the modem to which this entry is applicable. The value corresponds to the index of the corresponding modem in the entity table of the chassis MIB.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mdmMaChangeIndicator		1.3.6.1.4.1.429.1.6.19.1.1.2
A value of changed indicates that the card level configuration for a specific channel on a HDM is not the one in use on that channel.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notSupported(1), cfgChanged(2), cfgUnchanged(3)

mdmMaChannelConfig		1.3.6.1.4.1.429.1.6.19.1.1.3
Values of group(1), group(2), group(3), group(4) represent the HDM card level configuration of 1..4 used by this channel.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	group1(1), group2(2), group3(3), group4(4)