NETI-VAS-MIB

File: NETI-VAS-MIB.mib (106995 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMP-FRAMEWORK-MIB
INET-ADDRESS-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE enterprises
Counter32 Counter64 Unsigned32
Integer32 TEXTUAL-CONVENTION TimeStamp
TruthValue RowStatus RowPointer
DateAndTime SnmpAdminString InetAddressType
InetAddress InetPortNumber

Defined Types

VasConnectionStatus  
The connection state of the video transport. offline(0). The transport is disabled. connecting(1). The transport is in the process of being established. reconnecting(2). The transport has been established, but has then failed. Attempting to re-establish the connection. connected(3). The transport is connected and operational. unknown(9). The state is unknown.
TEXTUAL-CONVENTION    
  INTEGER offline(0), connecting(1), reconnecting(2), connected(3), unknown(9)  

VasCipher  
The cipher: none(0). Encryption is not used. aes128(1). AES-128, encrypted using Advanced Encryption Standard with 128-bit key length. aes192(1). AES-192, encrypted using Advanced Encryption Standard with 192-bit key length. aes256(1). AES-256, encrypted using Advanced Encryption Standard with 256-bit key length.
TEXTUAL-CONVENTION    
  INTEGER none(0), aes128(1), aes192(2), aes256(3)  

VasResetStatistics  
reset(0). Reset all statistics.
TEXTUAL-CONVENTION    
  INTEGER reset(0)  

VasVideoFormat  
Video format.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), fmt525i59(1), fmt625i50(2), fmt720p23(3), fmt720p24(4), fmt720p25(5), fmt720p29(6), fmt720p30(7), fmt720p50(8), fmt720p59(9), fmt720p60(10), fmt1080p23(11), fmt1080p24(12), fmt1080p25(13), fmt1080p29(14), fmt1080p30(15), fmt1080p50(16), fmt1080p59(17), fmt1080p60(18), fmt1080i50(19), fmt1080i59(20), fmt1080i60(21)  

VasIfEntry  
SEQUENCE    
  vasIfIndex Unsigned32
  vasIfName SnmpAdminString
  vasIfPurpose SnmpAdminString
  vasIfAdminStatus INTEGER
  vasIfOperStatus INTEGER
  vasIfFailure SnmpAdminString
  vasIfLastChanged TimeStamp
  vasIfResetStatistics VasResetStatistics
  vasIfInputFrom RowPointer
  vasIfPortMode INTEGER
  vasIfActiveFormat VasVideoFormat

VasEncPipeEntry  
SEQUENCE    
  vasEncPipeIndex Unsigned32
  vasEncPipeRowStatus RowStatus
  vasEncPipeName SnmpAdminString
  vasEncPipePurpose SnmpAdminString
  vasEncPipeAdminStatus INTEGER
  vasEncPipeOperStatus INTEGER
  vasEncPipeFailure SnmpAdminString
  vasEncPipeLastChanged TimeStamp
  vasEncPipeResetStatistics VasResetStatistics
  vasEncPipeStatsTr101 Unsigned32
  vasEncPipeEnableTr101 TruthValue
  vasEncPipeInputFrom RowPointer
  vasEncPipeCipher VasCipher
  vasEncPipeEncryptKey SnmpAdminString
  vasEncPipeProcessedFrames Counter32
  vasEncPipeCurrentTsBitrate Unsigned32
  vasEncPipeVideoBitrate Unsigned32

VasDecPipeEntry  
SEQUENCE    
  vasDecPipeIndex Unsigned32
  vasDecPipeRowStatus RowStatus
  vasDecPipeName SnmpAdminString
  vasDecPipePurpose SnmpAdminString
  vasDecPipeAdminStatus INTEGER
  vasDecPipeOperStatus INTEGER
  vasDecPipeFailure SnmpAdminString
  vasDecPipeLastChanged TimeStamp
  vasDecPipeResetStatistics VasResetStatistics
  vasDecPipeInputFrom RowPointer
  vasDecPipeCipher VasCipher
  vasDecPipeDecryptKey SnmpAdminString
  vasDecPipeProcessedFrames Counter32
  vasDecPipeCurrentTsBitrate Unsigned32
  vasDecPipeVideoBitrate Unsigned32

VasUdpSrcEntry  
SEQUENCE    
  vasUdpSrcIndex Unsigned32
  vasUdpSrcRowStatus RowStatus
  vasUdpSrcName SnmpAdminString
  vasUdpSrcPurpose SnmpAdminString
  vasUdpSrcAdminStatus INTEGER
  vasUdpSrcOperStatus INTEGER
  vasUdpSrcFailure SnmpAdminString
  vasUdpSrcLastChanged TimeStamp
  vasUdpSrcConnectionStatus VasConnectionStatus
  vasUdpSrcResetStatistics VasResetStatistics
  vasUdpSrcStatsUdp Unsigned32
  vasUdpSrcInputFrom RowPointer
  vasUdpSrcRemoteHostType InetAddressType
  vasUdpSrcRemoteHostAddress InetAddress
  vasUdpSrcRemotePort InetPortNumber
  vasUdpSrcLocalIfType InetAddressType
  vasUdpSrcLocalIfAddress InetAddress
  vasUdpSrcLocalPort InetPortNumber
  vasUdpSrcCipher VasCipher
  vasUdpSrcDecryptKey SnmpAdminString
  vasUdpSrcTtl Unsigned32
  vasUdpSrcDontFragment TruthValue

VasUdpSnkEntry  
SEQUENCE    
  vasUdpSnkIndex Unsigned32
  vasUdpSnkRowStatus RowStatus
  vasUdpSnkName SnmpAdminString
  vasUdpSnkPurpose SnmpAdminString
  vasUdpSnkAdminStatus INTEGER
  vasUdpSnkOperStatus INTEGER
  vasUdpSnkFailure SnmpAdminString
  vasUdpSnkLastChanged TimeStamp
  vasUdpSnkConnectionStatus VasConnectionStatus
  vasUdpSnkResetStatistics VasResetStatistics
  vasUdpSnkStatsUdp Unsigned32
  vasUdpSnkStatsTr101 Unsigned32
  vasUdpSnkEnableTr101 TruthValue
  vasUdpSnkRemoteInetType InetAddressType
  vasUdpSnkRemoteInetAddress InetAddress
  vasUdpSnkLocalIfType InetAddressType
  vasUdpSnkLocalIfAddress InetAddress
  vasUdpSnkLocalPort InetPortNumber
  vasUdpSnkCipher VasCipher
  vasUdpSnkEncryptKey SnmpAdminString
  vasUdpSnkMcastIpType InetAddressType
  vasUdpSnkMcastIp InetAddress
  vasUdpSnkSsmSourceIp InetAddress
  vasUdpSnkCompress TruthValue

VasPulSrcEntry  
SEQUENCE    
  vasPulSrcIndex Unsigned32
  vasPulSrcRowStatus RowStatus
  vasPulSrcName SnmpAdminString
  vasPulSrcPurpose SnmpAdminString
  vasPulSrcAdminStatus INTEGER
  vasPulSrcOperStatus INTEGER
  vasPulSrcFailure SnmpAdminString
  vasPulSrcLastChanged TimeStamp
  vasPulSrcConnectionStatus VasConnectionStatus
  vasPulSrcResetStatistics VasResetStatistics
  vasPulSrcStatsTrsp Unsigned32
  vasPulSrcRemoteInetType InetAddressType
  vasPulSrcRemoteInetAddress InetAddress
  vasPulSrcStreamId SnmpAdminString
  vasPulSrcInputFrom RowPointer
  vasPulSrcRemoteId SnmpAdminString
  vasPulSrcPassword SnmpAdminString

VasMpuSrcEntry  
SEQUENCE    
  vasMpuSrcIndex Unsigned32
  vasMpuSrcRowStatus RowStatus
  vasMpuSrcName SnmpAdminString
  vasMpuSrcPurpose SnmpAdminString
  vasMpuSrcAdminStatus INTEGER
  vasMpuSrcOperStatus INTEGER
  vasMpuSrcFailure SnmpAdminString
  vasMpuSrcLastChanged TimeStamp
  vasMpuSrcStreamId SnmpAdminString
  vasMpuSrcInputFrom RowPointer

VasPulSnkEntry  
SEQUENCE    
  vasPulSnkIndex Unsigned32
  vasPulSnkRowStatus RowStatus
  vasPulSnkName SnmpAdminString
  vasPulSnkPurpose SnmpAdminString
  vasPulSnkAdminStatus INTEGER
  vasPulSnkOperStatus INTEGER
  vasPulSnkFailure SnmpAdminString
  vasPulSnkLastChanged TimeStamp
  vasPulSnkConnectionStatus VasConnectionStatus
  vasPulSnkResetStatistics VasResetStatistics
  vasPulSnkStatsTrsp Unsigned32
  vasPulSnkStatsTr101 Unsigned32
  vasPulSnkEnableTr101 TruthValue
  vasPulSnkRemoteInetType InetAddressType
  vasPulSnkRemoteInetAddress InetAddress
  vasPulSnkStreamId SnmpAdminString
  vasPulSnkPassword SnmpAdminString
  vasPulSnkRemoteHostType InetAddressType
  vasPulSnkRemoteHostAddress InetAddress
  vasPulSnkRemoteHostType2 InetAddressType
  vasPulSnkRemoteHostAddress2 InetAddress
  vasPulSnkRemotePort InetPortNumber
  vasPulSnkRetransmitBuffer Unsigned32
  vasPulSnkFecMaxOverhead Unsigned32
  vasPulSnkFecOptimize TruthValue
  vasPulSnkFecLatency Unsigned32

VasPusSrcEntry  
SEQUENCE    
  vasPusSrcIndex Unsigned32
  vasPusSrcRowStatus RowStatus
  vasPusSrcName SnmpAdminString
  vasPusSrcPurpose SnmpAdminString
  vasPusSrcAdminStatus INTEGER
  vasPusSrcOperStatus INTEGER
  vasPusSrcFailure SnmpAdminString
  vasPusSrcLastChanged TimeStamp
  vasPusSrcConnectionStatus VasConnectionStatus
  vasPusSrcResetStatistics VasResetStatistics
  vasPusSrcStatsTrsp Unsigned32
  vasPusSrcRemoteInetType InetAddressType
  vasPusSrcRemoteInetAddress InetAddress
  vasPusSrcStreamId SnmpAdminString
  vasPusSrcInputFrom RowPointer
  vasPusSrcPassword SnmpAdminString
  vasPusSrcRemoteHostType InetAddressType
  vasPusSrcRemoteHostAddress InetAddress
  vasPusSrcRemoteHostType2 InetAddressType
  vasPusSrcRemoteHostAddress2 InetAddress
  vasPusSrcRemotePort InetPortNumber
  vasPusSrcLocalIfType InetAddressType
  vasPusSrcLocalIfAddress InetAddress
  vasPusSrcRetransmitBuffer Unsigned32
  vasPusSrcFecMaxOverhead Unsigned32
  vasPusSrcFecOptimize TruthValue
  vasPusSrcFecLatency Unsigned32

VasPusSnkEntry  
SEQUENCE    
  vasPusSnkIndex Unsigned32
  vasPusSnkRowStatus RowStatus
  vasPusSnkName SnmpAdminString
  vasPusSnkPurpose SnmpAdminString
  vasPusSnkAdminStatus INTEGER
  vasPusSnkOperStatus INTEGER
  vasPusSnkFailure SnmpAdminString
  vasPusSnkLastChanged TimeStamp
  vasPusSnkConnectionStatus VasConnectionStatus
  vasPusSnkResetStatistics VasResetStatistics
  vasPusSnkStatsTrsp Unsigned32
  vasPusSnkStatsTr101 Unsigned32
  vasPusSnkEnableTr101 TruthValue
  vasPusSnkRemoteInetType InetAddressType
  vasPusSnkRemoteInetAddress InetAddress
  vasPusSnkStreamId SnmpAdminString
  vasPusSnkPassword SnmpAdminString

VasUdpStatisticsEntry  
SEQUENCE    
  vasUdpStsIndex Unsigned32
  vasUdpStsOwner RowPointer
  vasUdpStsBitrate Unsigned32

VasTrspStatisticsEntry  
SEQUENCE    
  vasTrspIndex Unsigned32
  vasTrspOwner RowPointer
  vasTrspLastConnectionChange DateAndTime
  vasTrspConnects Unsigned32
  vasTrspDisconnects Unsigned32
  vasTrspNetRecvBitrate Unsigned32
  vasTrspNetRecvBurstLoss Counter32
  vasTrspNetRecvOctets Counter64
  vasTrspNetRecvLatency Unsigned32
  vasTrspNetRecvDropped Counter64
  vasTrspNetRecvJitter Unsigned32
  vasTrspNetRecvJitterRatio Integer32
  vasTrspNetRecvOutOfOrder Counter64
  vasTrspNetRecvOverflows Counter64
  vasTrspNetRecvPackets Counter64
  vasTrspNetRecvPacketRate Unsigned32
  vasTrspNetRecvPacketLoss Unsigned32
  vasTrspArqRecvAlmostDropped Counter64
  vasTrspArqRecvBitrate Unsigned32
  vasTrspArqRecvDropped Counter64
  vasTrspArqRecvDuplicates Counter64
  vasTrspArqRecvOverflows Counter64
  vasTrspArqRecvPackets Counter64
  vasTrspArqRecvRecovered Counter64
  vasTrspArqRecvRequests Counter64
  vasTrspNetSendBitrate Unsigned32
  vasTrspNetSendOctets Counter64
  vasTrspNetSendLimit Unsigned32
  vasTrspNetSendPackets Counter64
  vasTrspNetSendRtt Unsigned32
  vasTrspNetSendErrors Counter64
  vasTrspArqSendBitrate Unsigned32
  vasTrspArqSendIgnored Counter64
  vasTrspArqSendMissed Counter64
  vasTrspArqSendPacketRate Unsigned32
  vasTrspArqSendPackets Counter64
  vasTrspFecRecvBitrate Unsigned32
  vasTrspFecRecvPacketRate Unsigned32
  vasTrspFecRecvPackets Counter64
  vasTrspFecRecvRecovered Counter64
  vasTrspFecSendBitrate Unsigned32
  vasTrspFecSendPacketRate Unsigned32
  vasTrspFecSendPackets Counter64

Defined Values

netiVasMIB 1.3.6.1.4.1.2928.2.5
This document is work in progress, and it is likely to change. Reference: NID4613. MIB for Video Appliance Services. The MIB describes objects for setting up and monitoring of reliable video transports over an IP network. It also contains configuration objects for encoders and decoders. The MIB contains conceptual tables that describes the different objects: The table vasIfTable contains physical video ports, such as ASI or SDI ports. The table vasEncPipeTable contains video encoder pipelines. A video encoder pipeline can encode the video (e.g. from SDI to MPEG-4) to a stream, and process the audio, video and meta-data. The table vasDecPipeTable contains video decoder pipelines. A video decoder pipeline can decode a stream (from e.g. MPEG-4 to SDI) and process the audio, video and data in the stream. The table vasUdpSnkTable contains objects that receives an UDP video stream on an IP interface and provides it as an input to another source object. The table vasUdpSrcTable contains objects that takes a video stream from a sink object and transmits it as a UDP stream from an IP interface. This object is the complement to an object in the vasUdpSnkTable. The table vasPulSrcTable contains the source objects of a pull transport, i.e. a transport of a stream that is initiated at the sink side, where the stream is pulled from the source (sender) to the sink (receiver) at the sink. The table vasMpuSrcTable contains the source objects of pull transports, where multiple transports to different destinations may be setup from the same source. The table vasPulSnkTable contains the sink part of a pull transport, i.e. a transport of a stream that is initiated at the sink side, where the stream is pulled from the source (sender) to the sink (receiver) at the sink. The table vasPusSrcTable contains the source part of a push transport, i.e. a transport that is initiated from the source side, and is pushed from the source (sender) to the sink (receiver) at the source. The table vasPusSnkTable contains the sink part of a push transport, i.e. a transport that is initiated from the source side, and is pushed from the source (sender) to the sink (receiver) at the source. The MIB also contains tables for statistics.
MODULE-IDENTITY    

netinsight 1.3.6.1.4.1.2928
OBJECT IDENTIFIER    

netiGeneric 1.3.6.1.4.1.2928.2
OBJECT IDENTIFIER    

vasInterfaceGroup 1.3.6.1.4.1.2928.2.5.1
OBJECT IDENTIFIER    

vasEncoderPipeGroup 1.3.6.1.4.1.2928.2.5.2
OBJECT IDENTIFIER    

vasDecoderPipeGroup 1.3.6.1.4.1.2928.2.5.3
OBJECT IDENTIFIER    

vasTransportsGroup 1.3.6.1.4.1.2928.2.5.4
OBJECT IDENTIFIER    

vasStatisticsGroup 1.3.6.1.4.1.2928.2.5.5
OBJECT IDENTIFIER    

vasIfTable 1.3.6.1.4.1.2928.2.5.1.1
Table conceptual table contains video interfaces; physical video ports, such as ASI and SDI ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VasIfEntry

vasIfEntry 1.3.6.1.4.1.2928.2.5.1.1.1
An entry in the conceptual table represents one video interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  VasIfEntry  

vasIfIndex 1.3.6.1.4.1.2928.2.5.1.1.1.1
An index that uniquely identifies the interface in the table. The index is maintained across reboots of the node. The index is generally a small number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vasIfName 1.3.6.1.4.1.2928.2.5.1.1.1.2
A textual name of the interface. The name is unique within the node. The first part of the name is a string representing the type of interface, the second part of the name contains the device number followed by the port number within the device, separated by a semi-colon.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasIfPurpose 1.3.6.1.4.1.2928.2.5.1.1.1.3
A text that can describe the purpose of the interface. This is for administrative use.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

vasIfAdminStatus 1.3.6.1.4.1.2928.2.5.1.1.1.4
The administrative state of the interface. The value controls the desired state of the interface. up(1). The interface shall be enabled. down(2). The interface shall be disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasIfOperStatus 1.3.6.1.4.1.2928.2.5.1.1.1.5
The operational state of the interface. The value normally follow the state of the administrative state. up(1). The interface is up and operational. down(2). The interface is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasIfFailure should describe the fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasIfFailure 1.3.6.1.4.1.2928.2.5.1.1.1.6
A text describing the configuration or error status of the interface. The text is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasIfLastChanged 1.3.6.1.4.1.2928.2.5.1.1.1.7
The value of sysUpTime when status or configuration of the objects was last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vasIfResetStatistics 1.3.6.1.4.1.2928.2.5.1.1.1.8
Resets all statistics counters for the interface. (Not yet implemented).
Status: current Access: read-write
OBJECT-TYPE    
  VasResetStatistics  

vasIfInputFrom 1.3.6.1.4.1.2928.2.5.1.1.1.9
If the interface is an output interface, as set on vasIfPortMode, then this is a reference to the object that shall deliver the video stream to the interface. Which type of object that is a valid input depends on the type of interface. If the interface is an input interface, as set on the vasIfPortMode, then the value is always `.0.0'.
Status: current Access: read-write
OBJECT-TYPE    
  RowPointer  

vasIfPortMode 1.3.6.1.4.1.2928.2.5.1.1.1.10
Specifies how the interface shall operate. When the port is set as an input, then a video stream received on the physical port is distributed to the objects having this port as their input. When the port is set as an output, then a video stream received from the object referenced in vasIfInputFrom is transmitted on the physical port. asiInput(1). The port shall operate as an ASI input. asiOutput(2). The port shall operate as an ASI output. sdiInput(3). The port shall operate as an SDI input. sdiOutput(4). The port shall operate as an SDI output.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER asiInput(1), asiOutput(2), sdiInput(3), sdiOutput(4)  

vasIfActiveFormat 1.3.6.1.4.1.2928.2.5.1.1.1.11
The video source format.
Status: current Access: read-only
OBJECT-TYPE    
  VasVideoFormat  

vasEncPipeTable 1.3.6.1.4.1.2928.2.5.2.1
The conceptual table contains objects that represent video encoder pipelines. A video encoder pipeline can encode the video (e.g. from SDI to MPEG-4) to a stream, and process the audio, video and meta-data.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VasEncPipeEntry

vasEncPipeEntry 1.3.6.1.4.1.2928.2.5.2.1.1
An entry in the conceptual table represents one encoder pipeline.
Status: current Access: not-accessible
OBJECT-TYPE    
  VasEncPipeEntry  

vasEncPipeIndex 1.3.6.1.4.1.2928.2.5.2.1.1.1
An index that uniquely identifies the encoder pipeline in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vasEncPipeRowStatus 1.3.6.1.4.1.2928.2.5.2.1.1.2
See SNMPv2-TC. Use vasEncPipeAdminStatus to activate and de-activate an encoder pipeline. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new encoder pipeline. To activate the encoder pipeline, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The encoder pipeline is deleted. It can be deleted regardless of its operational state.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vasEncPipeName 1.3.6.1.4.1.2928.2.5.2.1.1.3
A textual name of the encoder pipeline. The name is automatically assigned by the system. The last part of the name is the index in this table.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasEncPipePurpose 1.3.6.1.4.1.2928.2.5.2.1.1.4
A text that can describe the purpose of the encoder pipeline. This is for administrative use.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasEncPipeAdminStatus 1.3.6.1.4.1.2928.2.5.2.1.1.5
The administrative state of the encoder pipeline. up(1). The encoder pipeline shall be enabled and allocates the necessary resources. down(2). The encoder pipeline shall be disabled and will not allocate any resources.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasEncPipeOperStatus 1.3.6.1.4.1.2928.2.5.2.1.1.6
The operational state of the encoder pipe. The value normally follow the state of the administrative state. up(1). The encoder pipe is up and operational. down(2). The encoder pipe is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasEncPipeFailure should describe the fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasEncPipeFailure 1.3.6.1.4.1.2928.2.5.2.1.1.7
A text describing the configuration or error status of the encoder pipeline. The text is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasEncPipeLastChanged 1.3.6.1.4.1.2928.2.5.2.1.1.8
The value of sysUpTime when status or configuration of the objects was last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vasEncPipeResetStatistics 1.3.6.1.4.1.2928.2.5.2.1.1.9
Resets all statistics counters for the encoder pipe. (Not yet implemented).
Status: current Access: read-write
OBJECT-TYPE    
  VasResetStatistics  

vasEncPipeStatsTr101 1.3.6.1.4.1.2928.2.5.2.1.1.10
Index for an entry in ETSI TR 101 290 statistics table for this object. (The table is not yet defined).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasEncPipeEnableTr101 1.3.6.1.4.1.2928.2.5.2.1.1.11
Enables or disables the ETSI TR 101 290 statistics collection.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vasEncPipeInputFrom 1.3.6.1.4.1.2928.2.5.2.1.1.12
A reference to the object that shall supply the video stream to the encoder pipe. This could be a physical input port in the vasIfTable, or a stream from e.g. a decoder pipe in the vasDecPipeTable. The value `.0.0' is used when no input is specified.
Status: current Access: read-create
OBJECT-TYPE    
  RowPointer  

vasEncPipeCipher 1.3.6.1.4.1.2928.2.5.2.1.1.13
A cipher to be used when encrypting the transport stream generated by the encoder pipeline.
Status: current Access: read-create
OBJECT-TYPE    
  VasCipher  

vasEncPipeEncryptKey 1.3.6.1.4.1.2928.2.5.2.1.1.14
The key to be used when encrypting the transport stream generated by the encoder pipeline. The key shall be provided as a text with hexadecimal digits presented as lower case characters.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasEncPipeProcessedFrames 1.3.6.1.4.1.2928.2.5.2.1.1.15
Running counter of number of encoded frames.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vasEncPipeCurrentTsBitrate 1.3.6.1.4.1.2928.2.5.2.1.1.16
Current transport stream bitrate in kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasEncPipeVideoBitrate 1.3.6.1.4.1.2928.2.5.2.1.1.17
Target video bitrate after encoding in kbps.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vasDecPipeTable 1.3.6.1.4.1.2928.2.5.3.1
The conceptual table contains objects that represent video decoder pipelines. A video decoder pipeline can decode a stream (from e.g. MPEG-4 to SDI) and process the audio, video and data in the stream.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VasDecPipeEntry

vasDecPipeEntry 1.3.6.1.4.1.2928.2.5.3.1.1
An entry in the conceptual table represents one decoder pipeline.
Status: current Access: not-accessible
OBJECT-TYPE    
  VasDecPipeEntry  

vasDecPipeIndex 1.3.6.1.4.1.2928.2.5.3.1.1.1
An index that uniquely identifies the decoder pipeline in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vasDecPipeRowStatus 1.3.6.1.4.1.2928.2.5.3.1.1.2
See SNMPv2-TC. Use vasDecPipeAdminStatus to activate and de-activate a decoder pipeline. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new decoder pipeline. To activate the decoder pipeline, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The decoder pipeline is deleted. It can be deleted regardless of its operational state.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vasDecPipeName 1.3.6.1.4.1.2928.2.5.3.1.1.3
A textual name of the decoder pipeline. The name is automatically assigned by the system. The last part of the name is the index in this table.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasDecPipePurpose 1.3.6.1.4.1.2928.2.5.3.1.1.4
A text that can describe the purpose of the decoder pipeline. This is for administrative use.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasDecPipeAdminStatus 1.3.6.1.4.1.2928.2.5.3.1.1.5
The administrative state of the decoder pipeline. up(1). The decoder pipeline shall be enabled and will allocate the necessary resources. down(2). The decoder pipeline shall be disabled and will not allocate any resources.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasDecPipeOperStatus 1.3.6.1.4.1.2928.2.5.3.1.1.6
The operational state of the decoder pipe. The value normally follow the state of the administrative state. up(1). The decoder pipe is up and operational. down(2). The decoder pipe is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasDecPipeFailure should describe the fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasDecPipeFailure 1.3.6.1.4.1.2928.2.5.3.1.1.7
A text describing the configuration or error status of the decoder pipeline. The text is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasDecPipeLastChanged 1.3.6.1.4.1.2928.2.5.3.1.1.8
The value of sysUpTime when status or configuration of the objects was last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vasDecPipeResetStatistics 1.3.6.1.4.1.2928.2.5.3.1.1.9
Resets all statistics counters for the decoder pipe. (Not yet implemented).
Status: current Access: read-write
OBJECT-TYPE    
  VasResetStatistics  

vasDecPipeInputFrom 1.3.6.1.4.1.2928.2.5.3.1.1.10
A reference to the object that shall supply the encoded video stream to the decoder pipe. This could be e.g. a pull or push transport sink in the vasPulSnkTable or vasPusSnkTable, or an encoder pipe in the vasEncPipeTable. The value `.0.0' is used when no input is specified.
Status: current Access: read-create
OBJECT-TYPE    
  RowPointer  

vasDecPipeCipher 1.3.6.1.4.1.2928.2.5.3.1.1.11
A cipher to be used when decrypting the transport stream.
Status: current Access: read-create
OBJECT-TYPE    
  VasCipher  

vasDecPipeDecryptKey 1.3.6.1.4.1.2928.2.5.3.1.1.12
The key to be used when decrypting the transport stream. The key shall be provided as a text with hexadecimal digits presented as lower case characters.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasDecPipeProcessedFrames 1.3.6.1.4.1.2928.2.5.3.1.1.13
Running counter of number of decoded frames.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vasDecPipeCurrentTsBitrate 1.3.6.1.4.1.2928.2.5.3.1.1.14
Current transport stream bitrate in kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasDecPipeVideoBitrate 1.3.6.1.4.1.2928.2.5.3.1.1.15
Video bitrate after decoding in kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasStreamPort 1.3.6.1.4.1.2928.2.5.4.1
The UDP port number that is used when listening at stream connections requests.
Status: current Access: read-write
OBJECT-TYPE    
  InetPortNumber  

vasUdpSrcTable 1.3.6.1.4.1.2928.2.5.4.2
The conceptual table contains objects that takes a video stream from a sink object and transmits it as a UDP stream from an IP interface. This object is the complement to an object in the vasUdpSnkTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VasUdpSrcEntry

vasUdpSrcEntry 1.3.6.1.4.1.2928.2.5.4.2.1
An entry in the conceptual table represents one UDP source.
Status: current Access: not-accessible
OBJECT-TYPE    
  VasUdpSrcEntry  

vasUdpSrcIndex 1.3.6.1.4.1.2928.2.5.4.2.1.1
An index that uniquely identifies the UDP source in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vasUdpSrcRowStatus 1.3.6.1.4.1.2928.2.5.4.2.1.2
See SNMPv2-TC. Use vasUdpSrcAdminStatus to activate and de-activate a UDP source. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new UDP source. To activate the UDP source, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The UDP source is deleted. It can be deleted regardless of its operational state.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vasUdpSrcName 1.3.6.1.4.1.2928.2.5.4.2.1.3
A textual name of the UDP source. The name is automatically assigned by the system. The last part of the name is the index in this table.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasUdpSrcPurpose 1.3.6.1.4.1.2928.2.5.4.2.1.4
A text that can describe the purpose of the UDP source. This is for administrative use.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasUdpSrcAdminStatus 1.3.6.1.4.1.2928.2.5.4.2.1.5
The administrative state of the UDP source. up(1). The UDP source shall be enabled and allocates the necessary resources. down(2). The UDP source shall be disabled and will not allocate any resources.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasUdpSrcOperStatus 1.3.6.1.4.1.2928.2.5.4.2.1.6
The operational state of the UDP source. The value normally follow the state of the administrative state. up(1). The UDP source is up and operational. down(2). The UDP source is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasUdpSrcFailure should describe the fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasUdpSrcFailure 1.3.6.1.4.1.2928.2.5.4.2.1.7
A string describing the configuration or error status of the object. The string is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasUdpSrcLastChanged 1.3.6.1.4.1.2928.2.5.4.2.1.8
The value of sysUpTime when status or configuration of the objects was last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vasUdpSrcConnectionStatus 1.3.6.1.4.1.2928.2.5.4.2.1.9
The status of the stream transport connection.
Status: current Access: read-only
OBJECT-TYPE    
  VasConnectionStatus  

vasUdpSrcResetStatistics 1.3.6.1.4.1.2928.2.5.4.2.1.10
Resets all statistics counters for the object. (Not yet implemented).
Status: current Access: read-write
OBJECT-TYPE    
  VasResetStatistics  

vasUdpSrcStatsUdp 1.3.6.1.4.1.2928.2.5.4.2.1.11
Index for an entry in statistics table vasUdpStatisticsTable for this object.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasUdpSrcInputFrom 1.3.6.1.4.1.2928.2.5.4.2.1.12
A reference to the object that shall supply the video stream to the UDP source. This could be e.g. a pull or push sink in the vasPulSnkTable or vasPusSnkTable, or a UDP sink in the vasUdpSnkTable. The value `.0.0' is used when no input is specified.
Status: current Access: read-create
OBJECT-TYPE    
  RowPointer  

vasUdpSrcRemoteHostType 1.3.6.1.4.1.2928.2.5.4.2.1.13
Describes how vasUdpSrcRemoteHostAddress shall be interpreted. Supported values are `unknown', `ipv4' and `dns'.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

vasUdpSrcRemoteHostAddress 1.3.6.1.4.1.2928.2.5.4.2.1.14
The IP address or DNS hostname of the remote source that shall provide the UDP stream.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

vasUdpSrcRemotePort 1.3.6.1.4.1.2928.2.5.4.2.1.15
The port number at the remote source that shall provide the UDP stream.
Status: current Access: read-create
OBJECT-TYPE    
  InetPortNumber  

vasUdpSrcLocalIfType 1.3.6.1.4.1.2928.2.5.4.2.1.16
Describes how the vasUdpSrcLocalIfAddress shall be interpreted. Supported value is `ipv4'.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

vasUdpSrcLocalIfAddress 1.3.6.1.4.1.2928.2.5.4.2.1.17
The IP address of a local interface (NIC) that shall be used as input for the video stream. If any interface can be used, set the IPv4 address 0.0.0.0.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

vasUdpSrcLocalPort 1.3.6.1.4.1.2928.2.5.4.2.1.18
The local UPD port number. Use 0 for any port.
Status: current Access: read-create
OBJECT-TYPE    
  InetPortNumber  

vasUdpSrcCipher 1.3.6.1.4.1.2928.2.5.4.2.1.19
The cipher to use for encrypting the UDP video stream.
Status: current Access: read-create
OBJECT-TYPE    
  VasCipher  

vasUdpSrcDecryptKey 1.3.6.1.4.1.2928.2.5.4.2.1.20
The key to be used when encrypting the UDP video stream. The key shall be provided as a text with hexadecimal digits presented as lower case characters.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasUdpSrcTtl 1.3.6.1.4.1.2928.2.5.4.2.1.21
TTL, the Time to Live (hop limit) for the UDP/IP datagram.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..255  

vasUdpSrcDontFragment 1.3.6.1.4.1.2928.2.5.4.2.1.22
The Don't Fragment (DF) flag on the IP packet. When set, then if fragmentation would be required to route a packet, the packet is dropped instead.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vasUdpSnkTable 1.3.6.1.4.1.2928.2.5.4.3
The conceptual table contains objects that receives a UDP video stream on an IP interface and provides it as an input to another source object.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VasUdpSnkEntry

vasUdpSnkEntry 1.3.6.1.4.1.2928.2.5.4.3.1
An entry in the conceptual table represents one UDP sink.
Status: current Access: not-accessible
OBJECT-TYPE    
  VasUdpSnkEntry  

vasUdpSnkIndex 1.3.6.1.4.1.2928.2.5.4.3.1.1
An index that uniquely identifies the UDP sink in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vasUdpSnkRowStatus 1.3.6.1.4.1.2928.2.5.4.3.1.2
See SNMPv2-TC. Use vasUdpSnkAdminStatus to activate and de-activate a UDP source. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new UDP sink. To activate the UDP sink, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The UDP sink is deleted. It can be deleted regardless of its operational state.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vasUdpSnkName 1.3.6.1.4.1.2928.2.5.4.3.1.3
A textual name of the UDP sink. The name is automatically assigned by the system. The last part of the name is the index in this table.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasUdpSnkPurpose 1.3.6.1.4.1.2928.2.5.4.3.1.4
A text that can describe the purpose of the UDP sink. This is for administrative use.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasUdpSnkAdminStatus 1.3.6.1.4.1.2928.2.5.4.3.1.5
The administrative state of the UDP sink. up(1). The UDP sink shall be enabled and allocates the necessary resources. down(2). The UDP sink shall be disabled and will not allocate any resources.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasUdpSnkOperStatus 1.3.6.1.4.1.2928.2.5.4.3.1.6
The operational state of the UDP sink. The value normally follow the state of the administrative state. up(1). The UDP sink is up and operational. down(2). The UDP sink is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasUdpSnkFailure should describe the fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasUdpSnkFailure 1.3.6.1.4.1.2928.2.5.4.3.1.7
A string describing the configuration or error status of the object. The string is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasUdpSnkLastChanged 1.3.6.1.4.1.2928.2.5.4.3.1.8
The value of sysUpTime when status or configuration of the objects was last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vasUdpSnkConnectionStatus 1.3.6.1.4.1.2928.2.5.4.3.1.9
The status of the stream transport connection.
Status: current Access: read-only
OBJECT-TYPE    
  VasConnectionStatus  

vasUdpSnkResetStatistics 1.3.6.1.4.1.2928.2.5.4.3.1.10
Resets all statistics counters for the object. (Not yet implemented).
Status: current Access: read-create
OBJECT-TYPE    
  VasResetStatistics  

vasUdpSnkStatsUdp 1.3.6.1.4.1.2928.2.5.4.3.1.11
Index for an entry in statistics table vasUdpStatisticsTable for this object.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasUdpSnkStatsTr101 1.3.6.1.4.1.2928.2.5.4.3.1.12
Index for an entry in ETSI TR 101 290 statistics table for this object. (The table is not yet defined).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasUdpSnkEnableTr101 1.3.6.1.4.1.2928.2.5.4.3.1.13
Enables or disables ETSI TR 101 290 statistics collection.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vasUdpSnkRemoteInetType 1.3.6.1.4.1.2928.2.5.4.3.1.14
Describes the format of vasUdpSnkRemoteInetAddress.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

vasUdpSnkRemoteInetAddress 1.3.6.1.4.1.2928.2.5.4.3.1.15
The IP address of the remote host from where the UDP stream is being received. The value is empty and vasUdpSnkRemoteInetType is `unknown' when a stream is not received.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

vasUdpSnkLocalIfType 1.3.6.1.4.1.2928.2.5.4.3.1.16
Describes how the vasUdpSnkLocalIfAddress shall be interpreted. Supported value is `ipv4'.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

vasUdpSnkLocalIfAddress 1.3.6.1.4.1.2928.2.5.4.3.1.17
The IP address of a local interface (NIC) that shall be used as input for the video stream. If any interface can be used, set the IPv4 address 0.0.0.0.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

vasUdpSnkLocalPort 1.3.6.1.4.1.2928.2.5.4.3.1.18
The local UDP port that shall be used for input.
Status: current Access: read-create
OBJECT-TYPE    
  InetPortNumber  

vasUdpSnkCipher 1.3.6.1.4.1.2928.2.5.4.3.1.19
The cipher that shall be used for decrypting the received UDP video stream.
Status: current Access: read-create
OBJECT-TYPE    
  VasCipher  

vasUdpSnkEncryptKey 1.3.6.1.4.1.2928.2.5.4.3.1.20
The key to be used when decrypting the UDP video stream. The key shall be provided as a text with hexadecimal digits presented as lower case characters.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasUdpSnkMcastIpType 1.3.6.1.4.1.2928.2.5.4.3.1.21
The format of vasUdpSnkMcastIp and vasUdpSnkSsmSourceIp. Supported values are `unknown' and `ipv4'.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

vasUdpSnkMcastIp 1.3.6.1.4.1.2928.2.5.4.3.1.22
The multicast IP address if joining a multicast UDP stream. Set empty and vasUdpSnkMcastIpType to `unknown' if not multicast.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

vasUdpSnkSsmSourceIp 1.3.6.1.4.1.2928.2.5.4.3.1.23
The source address if source-specific multicast (SSM) shall be used. Set to empty and vasUdpSnkMcastIpType to `unknown' if multicast shall not be used, or all-zero (0.0.0.0) if multicast but where SSM shall not be used.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

vasUdpSnkCompress 1.3.6.1.4.1.2928.2.5.4.3.1.24
Removes null-packets in an MPEG transport stream.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vasPulSrcTable 1.3.6.1.4.1.2928.2.5.4.4
The conceptual table contains objects that represent the source (sender) in a pull transport, i.e. a transport of a stream that is initiated from the sink side, where the stream is pulled from the source to the sink at the sink.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VasPulSrcEntry

vasPulSrcEntry 1.3.6.1.4.1.2928.2.5.4.4.1
An entry in the conceptual table represents one pull source object.
Status: current Access: not-accessible
OBJECT-TYPE    
  VasPulSrcEntry  

vasPulSrcIndex 1.3.6.1.4.1.2928.2.5.4.4.1.1
An index that uniquely identifies the pull source in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vasPulSrcRowStatus 1.3.6.1.4.1.2928.2.5.4.4.1.2
See SNMPv2-TC. Use vasPulSrcAdminStatus to activate and de-activate a Pull source. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new Pull source. To activate the Pull source, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The Pull source is deleted. It can be deleted regardless of its operational state.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vasPulSrcName 1.3.6.1.4.1.2928.2.5.4.4.1.3
A textual name of the Pull source. The name is automatically assigned by the system. The last part of the name is the index in this table.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasPulSrcPurpose 1.3.6.1.4.1.2928.2.5.4.4.1.4
A text that can describe the purpose of the Pull source. This is for administrative use.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasPulSrcAdminStatus 1.3.6.1.4.1.2928.2.5.4.4.1.5
The administrative state of the Pull source. The value controls the desired state of the Pull source. up(1). The Pull source shall be enabled. down(2). The Pull source shall be disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasPulSrcOperStatus 1.3.6.1.4.1.2928.2.5.4.4.1.6
The operational state of the Pull source. The value normally follow the state of the administrative state. up(1). The Pull source is up and operational. down(2). The Pull source is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasPulSrcFailure should describe the fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), dormant(3), partial(4)  

vasPulSrcFailure 1.3.6.1.4.1.2928.2.5.4.4.1.7
A string describing the configuration or error status of the object. The string is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasPulSrcLastChanged 1.3.6.1.4.1.2928.2.5.4.4.1.8
The value of sysUpTime when status or configuration of the objects was last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vasPulSrcConnectionStatus 1.3.6.1.4.1.2928.2.5.4.4.1.9
The status of the stream transport connection.
Status: current Access: read-only
OBJECT-TYPE    
  VasConnectionStatus  

vasPulSrcResetStatistics 1.3.6.1.4.1.2928.2.5.4.4.1.10
Resets all statistics counters for the object. (Not yet implemented).
Status: current Access: read-write
OBJECT-TYPE    
  VasResetStatistics  

vasPulSrcStatsTrsp 1.3.6.1.4.1.2928.2.5.4.4.1.11
Index for an entry in statistics vasTrspStatisticsTable table for this object.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasPulSrcRemoteInetType 1.3.6.1.4.1.2928.2.5.4.4.1.12
Format of vasPulSrcRemoteInetAddress.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

vasPulSrcRemoteInetAddress 1.3.6.1.4.1.2928.2.5.4.4.1.13
The IP address of the remote host to where the transport stream is being sent. The value is empty and vasPulSrcRemoteInetType is `unknown' when a stream is not sent.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

vasPulSrcStreamId 1.3.6.1.4.1.2928.2.5.4.4.1.14
Assigns the stream ID to a transport stream. The stream ID is a string that identifies the transport stream in all nodes where the stream exists. This must be unique within a node for any given transport stream.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasPulSrcInputFrom 1.3.6.1.4.1.2928.2.5.4.4.1.15
A reference to the object that shall supply the video stream to the pull source. This could be e.g. an encoder pipeline in the vasEncPipeTable or a UDP sink in the vasUdpSnkTable. The value `.0.0' is used when no input is specified.
Status: current Access: read-create
OBJECT-TYPE    
  RowPointer  

vasPulSrcRemoteId 1.3.6.1.4.1.2928.2.5.4.4.1.16
The remote ID is the assigned to the remote host where the transport stream is received. This is used for compatibility with nodes that does not implement this MIB. A node that implements this MIB is assigned the default value `nimbrava'.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasPulSrcPassword 1.3.6.1.4.1.2928.2.5.4.4.1.17
A password used for the transport stream. The vasPulSnkPassword on the sink at the remote host must match.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasMpuSrcTable 1.3.6.1.4.1.2928.2.5.4.5
The conceptual table contains objects that represent the source (sender) of pull transports, where multiple transports to different destinations may be setup from the same source.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VasMpuSrcEntry

vasMpuSrcEntry 1.3.6.1.4.1.2928.2.5.4.5.1
An entry in the conceptual table represents one multiple pull source object.
Status: current Access: not-accessible
OBJECT-TYPE    
  VasMpuSrcEntry  

vasMpuSrcIndex 1.3.6.1.4.1.2928.2.5.4.5.1.1
An index that uniquely identifies the multiple pull source in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vasMpuSrcRowStatus 1.3.6.1.4.1.2928.2.5.4.5.1.2
See SNMPv2-TC. Use vasMpuSrcAdminStatus to activate and de-activate an Multiple pull source. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new Multiple pull source. To activate the encoder pipeline, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The Multiple pull source is deleted. It can be deleted regardless of its operational state.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vasMpuSrcName 1.3.6.1.4.1.2928.2.5.4.5.1.3
A textual name of the Multiple pull source. The name is automatically assigned by the system. The last part of the name is the index in this table.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasMpuSrcPurpose 1.3.6.1.4.1.2928.2.5.4.5.1.4
A text that can describe the purpose of the Multiple pull source. This is for administrative use.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasMpuSrcAdminStatus 1.3.6.1.4.1.2928.2.5.4.5.1.5
The administrative state of the Multiple pull source. The value controls the desired state of the Multiple pull source. up(1). The Multiple pull source shall be enabled. down(2). The Multiple pull source shall be disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasMpuSrcOperStatus 1.3.6.1.4.1.2928.2.5.4.5.1.6
The operational state of the Multiple Pull source. The value normally follow the state of the administrative state. up(1). The Multiple pull source is up and operational. down(2). The Multiple pull source is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasMpuSrcFailure should describe the fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), dormant(3), partial(4)  

vasMpuSrcFailure 1.3.6.1.4.1.2928.2.5.4.5.1.7
A string describing the configuration or error status of the object. The string is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasMpuSrcLastChanged 1.3.6.1.4.1.2928.2.5.4.5.1.8
The value of sysUpTime when status or configuration of the objects was last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vasMpuSrcStreamId 1.3.6.1.4.1.2928.2.5.4.5.1.12
Assigns the stream ID to a transport stream. The stream ID is a string that identifies the transport stream in all nodes where the stream exists. This must be unique within a node for any given transport stream.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasMpuSrcInputFrom 1.3.6.1.4.1.2928.2.5.4.5.1.13
A reference to the object that shall supply the video stream to the multiple pull source. This could be e.g. an encoder pipeline on the vasEncPipeTable or a UDP sink in the vasUdpSnkTable. The value `.0.0' is used when no input is specified.
Status: current Access: read-create
OBJECT-TYPE    
  RowPointer  

vasPulSnkTable 1.3.6.1.4.1.2928.2.5.4.6
The conceptual table contains objects that represent the sink (receiver) of a pull transport, i.e. a transport of a stream that is initiated at the sink side, where the stream is pulled from the source to the sink at the sink.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VasPulSnkEntry

vasPulSnkEntry 1.3.6.1.4.1.2928.2.5.4.6.1
An entry in the conceptual table represents one pull sink object.
Status: current Access: not-accessible
OBJECT-TYPE    
  VasPulSnkEntry  

vasPulSnkIndex 1.3.6.1.4.1.2928.2.5.4.6.1.1
An index that uniquely identifies the pull sink in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vasPulSnkRowStatus 1.3.6.1.4.1.2928.2.5.4.6.1.2
See SNMPv2-TC. Use vasPulSnkAdminStatus to activate and de-activate a Pull sink. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new Pull sink. To activate the Pull sink, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The Pull sink is deleted. It can be deleted regardless of its operational state.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vasPulSnkName 1.3.6.1.4.1.2928.2.5.4.6.1.3
A textual name of the Pull sink. The name is automatically assigned by the system. The last part of the name is the index in this table.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasPulSnkPurpose 1.3.6.1.4.1.2928.2.5.4.6.1.4
A text that can describe the purpose of the Pull sink. This is for administrative use.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasPulSnkAdminStatus 1.3.6.1.4.1.2928.2.5.4.6.1.5
The administrative state of the Pull sink. The value controls the desired state of the Pull sink. up(1). The Pull sink shall be enabled. down(2). The Pull sink shall be disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasPulSnkOperStatus 1.3.6.1.4.1.2928.2.5.4.6.1.6
The operational state of the Pull sink. The value normally follow the state of the administrative state. up(1). The Pull sink is up and operational. down(2). The Pull sink is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasPulSnkFailure should describe the fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasPulSnkFailure 1.3.6.1.4.1.2928.2.5.4.6.1.7
A string describing the configuration or error status of the object. The string is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasPulSnkLastChanged 1.3.6.1.4.1.2928.2.5.4.6.1.8
The value of sysUpTime when status or configuration of the objects was last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vasPulSnkConnectionStatus 1.3.6.1.4.1.2928.2.5.4.6.1.9
The status of the stream transport connection.
Status: current Access: read-only
OBJECT-TYPE    
  VasConnectionStatus  

vasPulSnkResetStatistics 1.3.6.1.4.1.2928.2.5.4.6.1.10
Resets all statistics counters for the object. (Not yet implemented).
Status: current Access: read-write
OBJECT-TYPE    
  VasResetStatistics  

vasPulSnkStatsTrsp 1.3.6.1.4.1.2928.2.5.4.6.1.11
Index for an entry in statistics vasTrspStatisticsTable table for this object.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasPulSnkStatsTr101 1.3.6.1.4.1.2928.2.5.4.6.1.12
Index for an entry in ETSI TR 101 290 statistics table for this object. (The table is not yet defined).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasPulSnkEnableTr101 1.3.6.1.4.1.2928.2.5.4.6.1.13
Enables or disables ETSI TR 101 290 statistics collection.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vasPulSnkRemoteInetType 1.3.6.1.4.1.2928.2.5.4.6.1.14
Format of vasPulSrcRemoteInetAddress.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

vasPulSnkRemoteInetAddress 1.3.6.1.4.1.2928.2.5.4.6.1.15
The IP address of the remote host from where the transport stream is received. The value is empty and vasPulSnkRemoteInetType is `unknown' when a stream is not received.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

vasPulSnkStreamId 1.3.6.1.4.1.2928.2.5.4.6.1.16
Specifies the stream ID of the stream on the remote host that shall be received. The stream ID is a string that identifies the transport stream in all nodes where the stream exists. This must be unique within a node for any given transport stream.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasPulSnkPassword 1.3.6.1.4.1.2928.2.5.4.6.1.17
The password to use for the received transport stream. The password must match the vasPulSrcPassword set on the source at the remote host.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasPulSnkRemoteHostType 1.3.6.1.4.1.2928.2.5.4.6.1.18
Format of vasPulSnkRemoteHostAddress. Supported values are `unknown', `ipv4', and `dns'.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

vasPulSnkRemoteHostAddress 1.3.6.1.4.1.2928.2.5.4.6.1.19
The IP address or DNS hostname of the remote host from where the transport stream shall be pulled. This address is the first host that will be attempted when a transport stream is to be established.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

vasPulSnkRemoteHostType2 1.3.6.1.4.1.2928.2.5.4.6.1.20
Format of vasPulSnkRemoteHostAddress2. Supported values are `unknown', `ipv4', and `dns'.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

vasPulSnkRemoteHostAddress2 1.3.6.1.4.1.2928.2.5.4.6.1.21
The second IP address or DNS hostname of the remote host from where the transport stream shall be pulled. When using two addresses, then the transport is setup with two alternative sources. This is a second host that will be attempted if connection to the first host fails when a transport stream is to be established. If a second host shall not be used, then the value shall be empty and the vasPulSnkRemoteHostType shall be `unknown'.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

vasPulSnkRemotePort 1.3.6.1.4.1.2928.2.5.4.6.1.22
The UDP port on the remote host that the remote host is listening for connection attempts. See vaStreamPort.
Status: current Access: read-create
OBJECT-TYPE    
  InetPortNumber  

vasPulSnkRetransmitBuffer 1.3.6.1.4.1.2928.2.5.4.6.1.23
The size of the retransmission buffer in milliseconds (ms). The retransmission buffer setting adds bandwidth on the sender side to compensate for packet loss. The setting will affect the allowed maximum bitrate.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..30000  

vasPulSnkFecMaxOverhead 1.3.6.1.4.1.2928.2.5.4.6.1.24
The Forward Error Correction (FEC) overhead in percent (%) of the original stream bit rate. FEC increases the streams tolerance of burst errors and corrects for single errors, as long as they are not clustered, but at the cost of increased latency and is therefore not always desirable.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..100  

vasPulSnkFecOptimize 1.3.6.1.4.1.2928.2.5.4.6.1.25
Whether to automatically optimize Forward Error Correction (FEC). Optimization will favor the video stream and visually important frames, I and IDR-frames, over others, such as audio. Thereby lowering latency.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vasPulSnkFecLatency 1.3.6.1.4.1.2928.2.5.4.6.1.26
Forward Error Correction (FEC) block size in milliseconds (ms).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vasPusSrcTable 1.3.6.1.4.1.2928.2.5.4.7
The conceptual table contains objects that represent the source (sender) of a push transport, i.e. a transport that is initiated from the source side, and is pushed from the source to the sink at the source.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VasPusSrcEntry

vasPusSrcEntry 1.3.6.1.4.1.2928.2.5.4.7.1
An entry in the conceptual table represents one push source object.
Status: current Access: not-accessible
OBJECT-TYPE    
  VasPusSrcEntry  

vasPusSrcIndex 1.3.6.1.4.1.2928.2.5.4.7.1.1
An index that uniquely identifies the push source in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vasPusSrcRowStatus 1.3.6.1.4.1.2928.2.5.4.7.1.2
See SNMPv2-TC. Use vasPusSrcAdminStatus to activate and de-activate an Push source. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new Push source. To activate the Push source, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The Push source is deleted. It can be deleted regardless of its operational state.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vasPusSrcName 1.3.6.1.4.1.2928.2.5.4.7.1.3
A textual name of the Push source. The name is automatically assigned by the system. The last part of the name is the index in this table.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasPusSrcPurpose 1.3.6.1.4.1.2928.2.5.4.7.1.4
A text that can describe the purpose of the Push source. This is for administrative use.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasPusSrcAdminStatus 1.3.6.1.4.1.2928.2.5.4.7.1.5
The administrative state of the Push source. The value controls the desired state of the Push source. up(1). The Push source shall be enabled. down(2). The Push source shall be disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasPusSrcOperStatus 1.3.6.1.4.1.2928.2.5.4.7.1.6
The operational state of the Push source. The value normally follow the state of the administrative state. up(1). The Push source is up and operational. down(2). The Push source is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasPusSrcFailure should describe the fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasPusSrcFailure 1.3.6.1.4.1.2928.2.5.4.7.1.7
A string describing the configuration or error status of the object. The string is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasPusSrcLastChanged 1.3.6.1.4.1.2928.2.5.4.7.1.8
The value of sysUpTime when status or configuration of the objects was last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vasPusSrcConnectionStatus 1.3.6.1.4.1.2928.2.5.4.7.1.9
The status of the stream transport connection.
Status: current Access: read-only
OBJECT-TYPE    
  VasConnectionStatus  

vasPusSrcResetStatistics 1.3.6.1.4.1.2928.2.5.4.7.1.10
Resets all statistics counters for the object. (Not yet implemented).
Status: current Access: read-write
OBJECT-TYPE    
  VasResetStatistics  

vasPusSrcStatsTrsp 1.3.6.1.4.1.2928.2.5.4.7.1.11
Index for an entry in statistics vasTrspStatisticsTable table for this object.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasPusSrcRemoteInetType 1.3.6.1.4.1.2928.2.5.4.7.1.12
Format of vasPusSrcRemoteInetAddress.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

vasPusSrcRemoteInetAddress 1.3.6.1.4.1.2928.2.5.4.7.1.13
The IP address of the remote host to where the transport stream is being sent. The value is empty and vasPusSrcRemoteInetType is `unknown' when a stream is not sent.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

vasPusSrcStreamId 1.3.6.1.4.1.2928.2.5.4.7.1.14
Assigns the stream ID to a transport stream. The stream ID is a string that identifies the transport stream in all nodes where the stream exists. This must be unique within a node for any given transport stream.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasPusSrcInputFrom 1.3.6.1.4.1.2928.2.5.4.7.1.15
A reference to the object that shall supply the encoded video stream to the push source. This could be e.g. encoder pipeline in the vasEncPipeTable or a UDP sink in the vasUdpSnkTable. The value `.0.0' is used when no input is specified.
Status: current Access: read-create
OBJECT-TYPE    
  RowPointer  

vasPusSrcPassword 1.3.6.1.4.1.2928.2.5.4.7.1.16
A password used for the transport stream. The vasPusSnkPassword on the sink at the remote host must match.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasPusSrcRemoteHostType 1.3.6.1.4.1.2928.2.5.4.7.1.17
Format of vasPusSrcRemoteHostAddress. Supported values are `unknown', `ipv4' and `dns'.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

vasPusSrcRemoteHostAddress 1.3.6.1.4.1.2928.2.5.4.7.1.18
The IP address or DNS hostname of the remote host to where the transport stream shall be pushed. This address is the first host that will be attempted when a transport stream is to be established.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

vasPusSrcRemoteHostType2 1.3.6.1.4.1.2928.2.5.4.7.1.19
Format of vasPusSrcRemoteHostAddress2. Supported values are `unknown', `ipv4' and `dns'.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

vasPusSrcRemoteHostAddress2 1.3.6.1.4.1.2928.2.5.4.7.1.20
The second IP address or DNS hostname of the remote host to where the transport stream shall be pushed. This is a second host that will be attempted if connection to the first host fails when a transport stream is to be established. When using two addresses, the transport is setup to two alternative destinations. If a second host shall not be used, then the the value shall be empty and the vasPusSrcRemoteType2 shall be `unknown'.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

vasPusSrcRemotePort 1.3.6.1.4.1.2928.2.5.4.7.1.21
The UDP port number on the remote host that the remote host is listening for connection attempts. See vaStreamPort.
Status: current Access: read-create
OBJECT-TYPE    
  InetPortNumber  

vasPusSrcLocalIfType 1.3.6.1.4.1.2928.2.5.4.7.1.22
Describes how the vasPusSrcLocalIfAddress shall be interpreted. Supported value is `ipv4'.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

vasPusSrcLocalIfAddress 1.3.6.1.4.1.2928.2.5.4.7.1.23
The IP address of a local interface (NIC) that shall be used as output for the video stream. If any interface can be used, set the IPv4 address 0.0.0.0.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

vasPusSrcRetransmitBuffer 1.3.6.1.4.1.2928.2.5.4.7.1.24
The size of the retransmission buffer in milliseconds (ms). The retransmission buffer setting adds bandwidth on the sender side to compensate for packet loss. The setting will affect the allowed maximum bitrate.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..30000  

vasPusSrcFecMaxOverhead 1.3.6.1.4.1.2928.2.5.4.7.1.25
The Forward Error Correction (FEC) overhead in percent (%) of the original stream bit rate. FEC increases the streams tolerance of burst errors and corrects for single errors, as long as they are not clustered, but at the cost of increased latency and is therefore not always desirable.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..100  

vasPusSrcFecOptimize 1.3.6.1.4.1.2928.2.5.4.7.1.26
Whether to automatically optimize Forward Error Correction (FEC). Optimization will favor the video stream and visually important frames, I and IDR-frames, over others, such as audio. Thereby lowering latency.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vasPusSrcFecLatency 1.3.6.1.4.1.2928.2.5.4.7.1.27
Forward Error Correction (FEC) block size in milliseconds (ms).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vasPusSnkTable 1.3.6.1.4.1.2928.2.5.4.8
The conceptual table contains objects that represent the sink (receiver) of a push transport, i.e. a transport that is initiated from the source side, and is pushed from the source to the sink at the source.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VasPusSnkEntry

vasPusSnkEntry 1.3.6.1.4.1.2928.2.5.4.8.1
An entry in the conceptual table represents one push sink object.
Status: current Access: not-accessible
OBJECT-TYPE    
  VasPusSnkEntry  

vasPusSnkIndex 1.3.6.1.4.1.2928.2.5.4.8.1.1
An index that uniquely identifies the push sink in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vasPusSnkRowStatus 1.3.6.1.4.1.2928.2.5.4.8.1.2
See SNMPv2-TC. Use vasPusSnkAdminStatus to activate and de-activate an Push sink. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new Push sink. To activate the Push sink, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The Push sink is deleted. It can be deleted regardless of its operational state.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vasPusSnkName 1.3.6.1.4.1.2928.2.5.4.8.1.3
A textual name of the Push sink. The name is automatically assigned by the system. The last part of the name is the index in this table.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasPusSnkPurpose 1.3.6.1.4.1.2928.2.5.4.8.1.4
A text that can describe the purpose of the Push sink. This is for administrative use.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasPusSnkAdminStatus 1.3.6.1.4.1.2928.2.5.4.8.1.5
The administrative state of the Push sink. The value controls the desired state of the Push sink. up(1). The Push sink shall be enabled. down(2). The Push sink shall be disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasPusSnkOperStatus 1.3.6.1.4.1.2928.2.5.4.8.1.6
The operational state of the Push sink. The value normally follow the state of the administrative state. up(1). The Push sink is up and operational. down(2). The Push sink is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasPusSnkFailure should describe the fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

vasPusSnkFailure 1.3.6.1.4.1.2928.2.5.4.8.1.7
A string describing the configuration or error status of the object. The string is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

vasPusSnkLastChanged 1.3.6.1.4.1.2928.2.5.4.8.1.8
The value of sysUpTime when status or configuration of the objects was last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vasPusSnkConnectionStatus 1.3.6.1.4.1.2928.2.5.4.8.1.9
The status of the stream transport connection.
Status: current Access: read-only
OBJECT-TYPE    
  VasConnectionStatus  

vasPusSnkResetStatistics 1.3.6.1.4.1.2928.2.5.4.8.1.10
Resets all statistics counters for the object. (Not yet implemented).
Status: current Access: read-write
OBJECT-TYPE    
  VasResetStatistics  

vasPusSnkStatsTrsp 1.3.6.1.4.1.2928.2.5.4.8.1.11
Index for an entry in statistics vasTrspStatisticsTable table for this object.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasPusSnkStatsTr101 1.3.6.1.4.1.2928.2.5.4.8.1.12
Index for an entry in ETSI TR 101 290 statistics table for this object. (The table is not yet defined).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasPusSnkEnableTr101 1.3.6.1.4.1.2928.2.5.4.8.1.13
Enables or disables ETSI TR 101 290 statistics collection.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vasPusSnkRemoteInetType 1.3.6.1.4.1.2928.2.5.4.8.1.14
Format of vasPusSnkRemoteInetAddress.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

vasPusSnkRemoteInetAddress 1.3.6.1.4.1.2928.2.5.4.8.1.15
The IP address of the remote host from where the transport stream is received. The value is empty and the vasPusSnkRemoteInetType is `unknown' when a stream is not received.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

vasPusSnkStreamId 1.3.6.1.4.1.2928.2.5.4.8.1.16
Specifies the stream ID of the stream on the remote host that shall be received. The stream ID is a string that identifies the transport stream in all nodes where the stream exists. This must be unique within a node for any given transport stream.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasPusSnkPassword 1.3.6.1.4.1.2928.2.5.4.8.1.17
The password to use for the received transport stream. The password must match the vasPusSrcPassword set on the source at the remote host.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

vasUdpStatisticsTable 1.3.6.1.4.1.2928.2.5.5.1
The conceptual table contains perforamance data and counters for UDP video streams.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VasUdpStatisticsEntry

vasUdpStatisticsEntry 1.3.6.1.4.1.2928.2.5.5.1.1
An entry in the conceptual table represents statistical data for one UDP object.
Status: current Access: not-accessible
OBJECT-TYPE    
  VasUdpStatisticsEntry  

vasUdpStsIndex 1.3.6.1.4.1.2928.2.5.5.1.1.1
Index in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vasUdpStsOwner 1.3.6.1.4.1.2928.2.5.5.1.1.2
Reference to the object that allocated and uses this conceptual row.
Status: current Access: read-only
OBJECT-TYPE    
  RowPointer  

vasUdpStsBitrate 1.3.6.1.4.1.2928.2.5.5.1.1.3
Bitrate in bps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspStatisticsTable 1.3.6.1.4.1.2928.2.5.5.2
The conceptual table contains perforamance data and counters for transport streams.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VasTrspStatisticsEntry

vasTrspStatisticsEntry 1.3.6.1.4.1.2928.2.5.5.2.1
An entry in the conceptual table represents statistical data for one transport stream.
Status: current Access: not-accessible
OBJECT-TYPE    
  VasTrspStatisticsEntry  

vasTrspIndex 1.3.6.1.4.1.2928.2.5.5.2.1.1
Index in table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vasTrspOwner 1.3.6.1.4.1.2928.2.5.5.2.1.2
Reference to the object that allocated and uses this conceptual row.
Status: current Access: read-only
OBJECT-TYPE    
  RowPointer  

vasTrspLastConnectionChange 1.3.6.1.4.1.2928.2.5.5.2.1.3
Last connection status change time.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

vasTrspConnects 1.3.6.1.4.1.2928.2.5.5.2.1.4
Number of times that the connection state has changed to `connected'.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspDisconnects 1.3.6.1.4.1.2928.2.5.5.2.1.5
Number of times that the connection state has changed to `disconnected'.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspNetRecvBitrate 1.3.6.1.4.1.2928.2.5.5.2.1.6
Receive bitrate in kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspNetRecvBurstLoss 1.3.6.1.4.1.2928.2.5.5.2.1.7
Maximum number of packets that have been lost in a single burst error.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vasTrspNetRecvOctets 1.3.6.1.4.1.2928.2.5.5.2.1.8
The number of received octets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspNetRecvLatency 1.3.6.1.4.1.2928.2.5.5.2.1.9
Latency used for error correction, in milliseconds (ms).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspNetRecvDropped 1.3.6.1.4.1.2928.2.5.5.2.1.10
Number of packets dropped by the network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspNetRecvJitter 1.3.6.1.4.1.2928.2.5.5.2.1.11
Input jitter in milliseconds (ms).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspNetRecvJitterRatio 1.3.6.1.4.1.2928.2.5.5.2.1.12
Jitter ratio, for rate controlled streams.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vasTrspNetRecvOutOfOrder 1.3.6.1.4.1.2928.2.5.5.2.1.13
Number of packets received out of order.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspNetRecvOverflows 1.3.6.1.4.1.2928.2.5.5.2.1.14
Number of input jitter buffer overflows.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspNetRecvPackets 1.3.6.1.4.1.2928.2.5.5.2.1.15
Total number of received packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspNetRecvPacketRate 1.3.6.1.4.1.2928.2.5.5.2.1.16
Received packets per second.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspNetRecvPacketLoss 1.3.6.1.4.1.2928.2.5.5.2.1.17
Packet loss in millipercent (1/100,000)
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

vasTrspArqRecvAlmostDropped 1.3.6.1.4.1.2928.2.5.5.2.1.18
Number of packets that required more than half latency to recover.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspArqRecvBitrate 1.3.6.1.4.1.2928.2.5.5.2.1.19
Bitrate of received retransmissions in kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspArqRecvDropped 1.3.6.1.4.1.2928.2.5.5.2.1.20
Number of packets not recovered by either retransmissions or Forward Error Correction (FEC).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspArqRecvDuplicates 1.3.6.1.4.1.2928.2.5.5.2.1.21
Number of duplicated retransmission packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspArqRecvOverflows 1.3.6.1.4.1.2928.2.5.5.2.1.22
Number of packets dropped because of retransmission buffer overflow.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspArqRecvPackets 1.3.6.1.4.1.2928.2.5.5.2.1.23
Number of packets received by retransmission.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspArqRecvRecovered 1.3.6.1.4.1.2928.2.5.5.2.1.24
Number of packets recovered by retransmission.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspArqRecvRequests 1.3.6.1.4.1.2928.2.5.5.2.1.25
Number of sent retransmission requests.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspNetSendBitrate 1.3.6.1.4.1.2928.2.5.5.2.1.26
The send bitrate in kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspNetSendOctets 1.3.6.1.4.1.2928.2.5.5.2.1.27
The number of sent octets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspNetSendLimit 1.3.6.1.4.1.2928.2.5.5.2.1.28
The current sending limit in packets per second.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspNetSendPackets 1.3.6.1.4.1.2928.2.5.5.2.1.29
Total number of sent packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspNetSendRtt 1.3.6.1.4.1.2928.2.5.5.2.1.30
The return-trip time, RTT, in milliseconds (ms).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspNetSendErrors 1.3.6.1.4.1.2928.2.5.5.2.1.31
The number of packets failed to be sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspArqSendBitrate 1.3.6.1.4.1.2928.2.5.5.2.1.32
Bitrate of send retransmissions in kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspArqSendIgnored 1.3.6.1.4.1.2928.2.5.5.2.1.33
Number of ignored too frequent retransmission requests.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspArqSendMissed 1.3.6.1.4.1.2928.2.5.5.2.1.34
Number of ignored too late retransmission requests.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspArqSendPacketRate 1.3.6.1.4.1.2928.2.5.5.2.1.35
Retransmitted send packets per second.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspArqSendPackets 1.3.6.1.4.1.2928.2.5.5.2.1.36
Number of packets sent by retransmission.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspFecRecvBitrate 1.3.6.1.4.1.2928.2.5.5.2.1.37
The Forward Error Correction (FEC) receive overhead bitrate in kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspFecRecvPacketRate 1.3.6.1.4.1.2928.2.5.5.2.1.38
The Forward Error Correction (FEC) receive packet rate in packets per second.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspFecRecvPackets 1.3.6.1.4.1.2928.2.5.5.2.1.39
The number of received Forward Error Correction (FEC) packets
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspFecRecvRecovered 1.3.6.1.4.1.2928.2.5.5.2.1.40
The number of packets recovered by Forward Error Correction (FEC).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vasTrspFecSendBitrate 1.3.6.1.4.1.2928.2.5.5.2.1.41
The Forward Error Correction (FEC) send bitrate in kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspFecSendPacketRate 1.3.6.1.4.1.2928.2.5.5.2.1.42
The Forward Error Correction (FEC) receive packet rate in packets per second.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vasTrspFecSendPackets 1.3.6.1.4.1.2928.2.5.5.2.1.43
The number of sent Forward Error Correction (FEC) packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor