NEWBRIDGE-MIB

Imported modules

RFC1155-SMI	RFC-1212	RFC1213-MIB
NNCGNI00X1-SMI

Imported symbols

enterprises	Counter	OBJECT-TYPE
DisplayString	PhysAddress	nncInterimMib

Defined Types

AlarmCode
INTEGER	1..255

AlarmQueue
INTEGER	major(1), minor(2), diag(3)

AlarmQueueIndex
INTEGER	1..64

ExtendedCounter
OCTET STRING	Size(8..8)

ExtendedTime
OCTET STRING	Size(8..8)

PositionNumber
INTEGER

CircuitNumber
INTEGER	1..32

DescendantNumber
INTEGER	1..1023

DeviceNumber
OCTET STRING

ModuleType
INTEGER

ModuleID
INTEGER

SubModuleType
INTEGER

SubModuleID
INTEGER

FilterEntry
OCTET STRING	Size(8..8)

BridgeIdentifier
OCTET STRING	Size(8..8)

InterfaceIndex
INTEGER

OneByte
INTEGER	0..255

T1E1Loopback
INTEGER	none(1), equipment(2), equipment-all-ones(3), equipment-digital(4), line(5), line-and-equipment(6)

T1E1Status
INTEGER	0..65535

ControlLeads
INTEGER	0..255

NnciSystemTableEntry
SEQUENCE
	nnciSystemDate	DisplayString
	nnciSystemProductName	DisplayString
	nnciSystemGeneric	DisplayString
	nnciSystemNVMAllocation	OCTET STRING
	nnciSystemNVMRepairInfo	OCTET STRING
	nnciSystemTime	DisplayString

NnciSerialPortTableEntry
SEQUENCE
	nnciSpBaudRate	INTEGER
	nnciSpWordLength	INTEGER
	nnciSpStopBits	INTEGER
	nnciSpParity	INTEGER

NnciAlarmTableEntry
SEQUENCE
	nnciAlarmCount	INTEGER
	nnciAlarmQueueEntry	OCTET STRING
	nnciAlarmQueueEntryStatus	INTEGER
	nnciAlarmSeqNum	INTEGER
	nnciAlarmCodePriority	INTEGER
	nnciAlarmsDeleteQueueEntry	INTEGER
	nnciAlarmQueueType	INTEGER

NnciDiagTableEntry
SEQUENCE
	nnciDiagEnableBackground	INTEGER
	nnciDiagResults	INTEGER

NnciNetSynchTableEntry
SEQUENCE
	nnciNetSynchSourceStatus	INTEGER
	nnciNetSynchTimingSource	INTEGER
	nnciNetSynchReacquisitionMode	INTEGER
	nnciNetSynchCurrentSource	INTEGER
	nnciNetSynchRecoveryInterval	INTEGER
	nnciNetSynchQuality	INTEGER
	nnciNetSynchSourceClass	INTEGER
	nnciNetSynchNodeClass	INTEGER

NnciSlotTableEntry
SEQUENCE
	nnciSlotName	DisplayString
	nnciSlotProgType	ModuleType
	nnciSlotPresType	ModuleType
	nnciSlotStatus	INTEGER
	nnciSlotModuleID	ModuleID
	nnciSlotSubModuleProgType	SubModuleType
	nnciSlotSubModulePresType	SubModuleType
	nnciSlotFirmwareID	INTEGER
	nnciSlotBusyOut	INTEGER
	nnciSlotSubModuleID	SubModuleID
	nnciSlotVariantID	INTEGER
	nnciSlotResetCard	INTEGER
	nnciSlotHardwareRevision	INTEGER

NnciT1SlotTableEntry
SEQUENCE
	nnciT1SlotAlarmControl	INTEGER
	nnciT1SlotFramingStyle	INTEGER
	nnciT1SlotZeroSuppression	INTEGER
	nnciT1SlotLinkStatus	T1E1Status
	nnciT1SlotLoopLength	INTEGER
	nnciT1SlotThreshold	INTEGER
	nnciT1SlotLoopback	T1E1Loopback
	nnciT1SlotTrunkConditioningEnable	INTEGER
	nnciT1SlotAlarmDeclarationTime	INTEGER
	nnciT1SlotAlarmClearingTime	INTEGER
	nnciT1SlotCRCFraming	INTEGER

NnciE1SlotTableEntry
SEQUENCE
	nnciE1SlotAlarmControl	INTEGER
	nnciE1SlotLoopback	T1E1Loopback
	nnciE1SlotSignalling	INTEGER
	nnciE1SlotShieldLevel	INTEGER
	nnciE1SlotLinkStatus	T1E1Status
	nnciE1SlotThreshold	INTEGER
	nnciE1TypeOfStats	INTEGER
	nnciE1SlotTrunkConditioningEnable	INTEGER
	nnciE1SlotAlarmDeclarationTime	INTEGER
	nnciE1SlotAlarmClearingTime	INTEGER
	nnciE1SlotCRCFraming	INTEGER

NnciDevTableEntry
SEQUENCE
	nnciDevName	DisplayString
	nnciDevLoopback	INTEGER
	nnciDevMateDevice	DeviceNumber
	nnciDevSetShowSig	INTEGER
	nnciDevReady	INTEGER
	nnciDevActive	INTEGER
	nnciDevConnected	INTEGER
	nnciDevOutOfService	INTEGER
	nnciDevUnderMaintenance	INTEGER
	nnciDevBusyOut	INTEGER
	nnciDevFailed	INTEGER
	nnciDevDiagEnable	INTEGER

NnciT1TableEntry
SEQUENCE
	nnciT1BusyOut	INTEGER
	nnciT1RobbedBitSig	INTEGER
	nnciT1Inversion	INTEGER
	nnciT1DefaultData	OneByte
	nnciT1FirstCode	INTEGER
	nnciT1SecondCode	INTEGER
	nnciT1PartOfSuperRate	CircuitNumber
	nnciT1BitsUsed	INTEGER
	nnciT1SuperRateCircuitMap	INTEGER
	nnciT1SuperRateNumCircuits	INTEGER

NnciE1TableEntry
SEQUENCE
	nnciE1BusyOut	INTEGER
	nnciE1AlternateDigitInversion	INTEGER
	nnciE1DefaultData	OneByte
	nnciE1FirstCode	INTEGER
	nnciE1SecondCode	INTEGER
	nnciE1PartOfSuperRate	CircuitNumber
	nnciE1BitsUsed	INTEGER
	nnciE1SuperRateCircuitMap	INTEGER
	nnciE1SuperRateNumCircuits	INTEGER

NnciSdcTableEntry
SEQUENCE
	nnciSdcInterfaceControl	INTEGER
	nnciSdcInterfaceSpeed	INTEGER
	nnciSdcLeadsDefaultOn	ControlLeads
	nnciSdcLeadDefaultOff	ControlLeads
	nnciSdcInterfaceStatus	ControlLeads

NnciHdlcTableEntry
SEQUENCE
	nnciHdlcBytesTransmitted	ExtendedCounter
	nnciHdlcFramesTransmitted	ExtendedCounter
	nnciHdlcRxGoodBytes	ExtendedCounter
	nnciHdlcRxGoodFrames	ExtendedCounter
	nnciHdlcUnderrun	ExtendedCounter
	nnciHdlcCRCError	ExtendedCounter
	nnciHdlcAlignmentError	ExtendedCounter
	nnciHdlcOverrun	ExtendedCounter
	nnciHdlcAbort	ExtendedCounter
	nnciHdlcSinceLastReset	ExtendedTime
	nnciHdlcApplication	INTEGER

NnciBridgeTableEntry
SEQUENCE
	nnciBrdgAddress	PhysAddress
	nnciBrdgUptime	ExtendedTime
	nnciBrdgInterfaceCount	INTEGER
	nnciBrdgMaxInterfaceCount	INTEGER
	nnciBrdgMapCircuitToInterface	InterfaceIndex

NnciFilterTableEntry
SEQUENCE
	nnciFilterReset	INTEGER
	nnciFilterLearn	INTEGER
	nnciFilterPermDBChange	INTEGER
	nnciFilterPermDBEntryCount	INTEGER
	nnciFilterPermDBContents	FilterEntry
	nnciFilterAddPermDBEntry	FilterEntry
	nnciFilterDeletePermDBEntry	FilterEntry
	nnciFilterAFMaxEntries	INTEGER
	nnciFilterAFEntryLifetime	INTEGER
	nnciFilterAFEntryCount	INTEGER
	nnciFilterAFContents	FilterEntry
	nnciFilterForwardMatrix	INTEGER
	nnciFilterFloodUnicastMatrix	INTEGER
	nnciFilterTakeSnapShot	INTEGER
	nnciFilterFloodMulticastMatrix	INTEGER
	nnciFilterFloodBroadcastMatrix	INTEGER
	nnciFilterPermNVDBContents	FilterEntry
	nnciFilterDeleteAllPermEntries	INTEGER

NnciStpTableEntry
SEQUENCE
	nnciStpEnable	INTEGER
	nnciStpBridgePriority	INTEGER
	nnciStpRoot	BridgeIdentifier
	nnciStpRootPathCost	INTEGER
	nnciStpRootInterface	InterfaceIndex
	nnciStpMaxAge	INTEGER
	nnciStpHelloTime	INTEGER
	nnciStpForwardDelay	INTEGER
	nnciStpMyMaxAge	INTEGER
	nnciStpMyHelloTime	INTEGER
	nnciStpMyForwardDelay	INTEGER
	nnciStpTopologyChangeDetected	INTEGER
	nnciStpSendingTopologyChange	INTEGER
	nnciStpTimeSinceLastTopologyChange	ExtendedTime
	nnciStpTopologyChanges	Counter
	nnciStpTopologyChangeAck	INTEGER
	nnciStpInterfacePriority	INTEGER
	nnciStpInterfaceCost	INTEGER
	nnciStpDesignatedBridge	BridgeIdentifier
	nnciStpDesignatedInterface	InterfaceIndex
	nnciStpDesignatedRoot	BridgeIdentifier
	nnciStpDesignatedCost	INTEGER
	nnciStpConfigurationMessagePending	INTEGER
	nnciStpAllowableDeviations	INTEGER
	nnciStpCostMultiplier	INTEGER
	nnciStpUserAssignedCost	INTEGER

Defined Values

nnciSystem		1.3.6.1.4.1.123.2.1
OBJECT IDENTIFIER

nnciSp		1.3.6.1.4.1.123.2.2
OBJECT IDENTIFIER

nnciAlarm		1.3.6.1.4.1.123.2.4
OBJECT IDENTIFIER

nnciDiag		1.3.6.1.4.1.123.2.3
OBJECT IDENTIFIER

nnciNetSynch		1.3.6.1.4.1.123.2.7
OBJECT IDENTIFIER

nnciSlot		1.3.6.1.4.1.123.2.10
OBJECT IDENTIFIER

nnciT1Slot		1.3.6.1.4.1.123.2.22
OBJECT IDENTIFIER

nnciE1Slot		1.3.6.1.4.1.123.2.20
OBJECT IDENTIFIER

nnciDev		1.3.6.1.4.1.123.2.11
OBJECT IDENTIFIER

nnciT1		1.3.6.1.4.1.123.2.23
OBJECT IDENTIFIER

nnciE1		1.3.6.1.4.1.123.2.21
OBJECT IDENTIFIER

nnciSdc		1.3.6.1.4.1.123.2.72
OBJECT IDENTIFIER

nnciHdlc		1.3.6.1.4.1.123.2.66
OBJECT IDENTIFIER

nnciBridge		1.3.6.1.4.1.123.2.55
OBJECT IDENTIFIER

nnciBrdgSt		1.3.6.1.4.1.123.2.61
OBJECT IDENTIFIER

nnciFilter		1.3.6.1.4.1.123.2.62
OBJECT IDENTIFIER

nnciStp		1.3.6.1.4.1.123.2.63
OBJECT IDENTIFIER

nnciSystemTable		1.3.6.1.4.1.123.2.1.1
This table contains interesting general information about the managed element in its entirety
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciSystemTableEntry

nnciSystemTableEntry		1.3.6.1.4.1.123.2.1.1.1
A list of general information about the managed element
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciSystemTableEntry

nnciSystemDate		1.3.6.1.4.1.123.2.1.1.1.2
The current date as known by the node.The date is formatted as a sequence of nine ASCII characters in the form DD-MMM-YY, where DD is the day of the month (01..31), MMM is the month of the year, e.g. JAN, and YY is the last two digits of the year, e.g. 90.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

nnciSystemProductName		1.3.6.1.4.1.123.2.1.1.1.4
The marketing name for the product, e.g. 8230 MainStreet for something if sysObjectId.0 = nnci8230
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

nnciSystemGeneric		1.3.6.1.4.1.123.2.1.1.1.5
This object identifies the revision of the firmware in the standard Newbridge fashion. The identifier is a string of 10 ASCII characters of the form M11D-HL-PP where: D indicates the release number of the software LL indicates the load of the software, and PP indicates the patch-level of the firmware.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

nnciSystemNVMAllocation		1.3.6.1.4.1.123.2.1.1.1.30
This object provides status information about the non-volatile memory present on the main card of the system. The information returned includes the size of a single block of NVM, the total number of blocks available for use, the number of bad blocks and the number of blocks in use.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

nnciSystemNVMRepairInfo		1.3.6.1.4.1.123.2.1.1.1.31
This object returns the details of the latest repair performed on the non-volatile memory present on the main card.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

nnciSystemTime		1.3.6.1.4.1.123.2.1.1.1.38
The current time of day including seconds. The time is represented as a sequence of 9 ASCII characters in the form HH:MM:SS, where HH is the hour of the day (0..12), MM is the minute of the hour and SS are the seconds of the minute (0..59)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

nnciSerialPortTable		1.3.6.1.4.1.123.2.2.1
This table contains the configuration information for an asynchronous management port for a standalone node.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciSerialPortTableEntry

nnciSerialPortTableEntry		1.3.6.1.4.1.123.2.2.1.1
A list of configuration information for a management port on a standalone node
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciSerialPortTableEntry

nnciSpBaudRate		1.3.6.1.4.1.123.2.2.1.1.1
The baud rate of the asynchronous management port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), b300(2), b600(3), b1200(4), b2400(5), b4800(6), b9600(7), b38400(8)

nnciSpWordLength		1.3.6.1.4.1.123.2.2.1.1.2
The word length used on the asynchronous management port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	seven(3), eight(4)

nnciSpStopBits		1.3.6.1.4.1.123.2.2.1.1.3
The number of stop bits used by the asynchronous management port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciSpParity		1.3.6.1.4.1.123.2.2.1.1.4
The parity used on the asynchronous management port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	odd(1), even(2), none(3)

nnciAlarmTable		1.3.6.1.4.1.123.2.4.1
This table contains all the configuration and status information about the alarm mechanism along with the alarms themselves.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciAlarmTableEntry

nnciAlarmTableEntry		1.3.6.1.4.1.123.2.4.1.1
A list of all of the configuration and status information for a node, along with the alarm queues themselves.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciAlarmTableEntry

nnciAlarmCount		1.3.6.1.4.1.123.2.4.1.1.1
The number of alarms in the specified queue.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciAlarmQueueEntry		1.3.6.1.4.1.123.2.4.1.1.2
When read, this object returns the particulars of the entry in the specified queue.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

nnciAlarmQueueEntryStatus		1.3.6.1.4.1.123.2.4.1.1.3
The status of an alarm.
Status: mandatory	Access: write-only
OBJECT-TYPE
	INTEGER	nonTep1e(0), unackNotRemedied(1), unackRedmedyUnack(2), ackNotRemedied(3), ackRemedyUnack(4), ackRemedyAck(5), clearingAlarmUnack(6), clearingAlarmAck(7)

nnciAlarmSeqNum		1.3.6.1.4.1.123.2.4.1.1.4
The next sequence number that will be used by the node. The sequence numbers are a unique, within a single node, identifier for an alarm.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciAlarmCodePriority		1.3.6.1.4.1.123.2.4.1.1.6
This value of this object controls into which queue an alarm is placed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	major(1), minor(2), diagnostic(3)

nnciAlarmDeleteQueueEntry		1.3.6.1.4.1.123.2.4.1.1.8
A set to this object is deletes the first N alarms from the specified alarm queue.
Status: mandatory	Access: write-only
OBJECT-TYPE
	INTEGER

nnciAlarmQueueType		1.3.6.1.4.1.123.2.4.1.1.9
This paramater is used to control the behaviour of the alarm queue in the overlfow case, i.e. when the alarm facility attempts to place the 65th alarm into the queue. If the queue type is set to Fixed, the 65th and 64th alarms will be discarded and the 'Too Many Alarms' alarm added as the last entry in the queue. If the queue type is set to Circular, the 65th alarm will overwrite the first alarm in the queue
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	fixedAlarmQueue(1), circularAlarmQueue(2)

nnciDiagTable		1.3.6.1.4.1.123.2.3.1
This table contains all of the configuration and status information related to diagnostics on a node.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciDiagTableEntry

nnciDiagTableEntry		1.3.6.1.4.1.123.2.3.1.1
A list of all of the configuration and status information related to node diagnostics.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciDiagTableEntry

nnciDiagEnable		1.3.6.1.4.1.123.2.3.1.1.1
This object controls whether or not background diagnostics are run. If the object is set to 2 (enabled), then background diagnostics are run periodically. If the object is set to 1 (disabled), background diagnostics are not performed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

nnciDiagResults		1.3.6.1.4.1.123.2.3.1.1.5
This object indicates the results of power on and background diagnostics. Any bit that is asserted corresponds to a failure of a component of the card.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciNetSynchTable		1.3.6.1.4.1.123.2.7.1
This table contains all of the configuration and status information for the network synchronization mechanism for a standalone node.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciNetSynchTableEntry

nnciNetSynchTableEntry		1.3.6.1.4.1.123.2.7.1.1
A list of all of the configuration and status information related to network synchronization.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciNetSynchTableEntry

nnciNetSynchSourceStatus		1.3.6.1.4.1.123.2.7.1.1.1
This object returns the current status of the specified source of synchronization. A set to this object changes the enabled/disabled status of the source. If the source is disabled, writing anything other than 'Disabled' will cause the source to be enabled, and its state will change to one of Not Ready, Ready, or Current. If the source is enabled, writing 'Disabled' to this object will disable the source.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), ready(2), current(3), timedRecovery(4), failed(5), shutDown(6), notReady(7), autoRecovery(8), cannotLock(9), enabled(10), illegalState(11), undefinedSource(12), unavailable(13), acquiring(14)

nnciNetSynchTimingSource		1.3.6.1.4.1.123.2.7.1.1.2
The device which provides timing when the specified source of synchronization is selected. The sync source must be disabled before changing this object.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	exp1(3), exp2(4), freerun(18)

nnciNetSynchReacquisitionMode		1.3.6.1.4.1.123.2.7.1.1.3
How the source of synchronization will be treated in the event a failure is detected. If Manual is selected, the source will remain unused until it is re-selected. If Automatic recovery is selected, the source will be returned to use as soon as it is valid, e.g. when a T1 link regains frame alignment. If Timed recovery is selected, the node will attempt to use the source at the specified interval.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	manual(1), automatic(2), timed(3)

nnciNetSynchCurrentSource		1.3.6.1.4.1.123.2.7.1.1.4
The current source of synchronization for the node. A set to this object toggles the ready/current status of the source. If the source is ready, it will become the current source. If the source is current, it will become ready, and the next-best source will become the current source. If the source is neither ready nor current, a set to this object has no effect.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciNetSynchRecoveryInterval		1.3.6.1.4.1.123.2.7.1.1.6
This object is used to set the interval between recovery attempts for a source of synchronization that is using Timed recovery in seconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciNetSynchQuality		1.3.6.1.4.1.123.2.7.1.1.9
This object is used to set the maximum permissible number of failures that can be experienced by a source in an hour. If this limit is exceeded, an alarm is raised and the source is placed into the disabled state.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciNetSynchSourceClass		1.3.6.1.4.1.123.2.7.1.1.11
This object is used to set the class of a source. The source with the best class will provide system sync when several sources are Ready. Note that the freerun source (source 5) does not actually make use of this object. It gets its class from nnciNetSynchNodeClass.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciNetSynchNodeClass		1.3.6.1.4.1.123.2.7.1.1.12
This object is used to set the class of the node. The node will freerun if the value of this object is lower than the nnciNetSynchSourceClass of the other sources.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciSlotTable		1.3.6.1.4.1.123.2.10.1
This table contains all of the common, slot configuration and status information for a standalone node
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciSlotTableEntry

nnciSlotTableEntry		1.3.6.1.4.1.123.2.10.1.1
A list of all of the common, per-slot configuration and status information for a standalone node.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciSlotTableEntry

nnciSlotName		1.3.6.1.4.1.123.2.10.1.1.1
An arbitrary name for a slot.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

nnciSlotProgType		1.3.6.1.4.1.123.2.10.1.1.2
This object is used to specify what kind of module should be present in the specified position . If the value in this object does not match the value in the nnciSlotPresType object, then the position will be held out of service.
Status: mandatory	Access: read-write
OBJECT-TYPE
	ModuleType

nnciSlotPresType		1.3.6.1.4.1.123.2.10.1.1.3
This object is used to specify what kind of module is present in the specified position . If the value of this object does not match the value of the nnciSlotProgType object, the position will be held out of service.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ModuleType

nnciSlotStatus		1.3.6.1.4.1.123.2.10.1.1.4
This object contains the current status of the specified position . The status reflects whether a module is present, and if so, is it of the expected type.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	empty(1), ok(2), fault-on-module(3), module-dead(4), unknown-module-type(5), module-type-mismatch(6), sub-module-type-mismatch(7), wrong-firmware(9), wrong-variant(12)

nnciSlotModuleID		1.3.6.1.4.1.123.2.10.1.1.5
The hardware identification number assigned to the module that is present in the specified position. If there is no module installed in the position, the value returned will be 0 (zero). Note that this identification number identifies what kind of module is present; the revision level of the module is available in the nnciSlotHardwareRevision object
Status: mandatory	Access: read-only
OBJECT-TYPE
	ModuleID

nnciSlotSubModuleProgType		1.3.6.1.4.1.123.2.10.1.1.6
What kind of 'sub-module' should be present in the specified slot. If the value in this object does not match the value in the nnciSlotModulePresType object, then the position will be held out of service. Any attempt to set this object for other than the expansion module positions will be rejected.
Status: mandatory	Access: read-write
OBJECT-TYPE
	SubModuleType

nnciSlotSubModulePresType		1.3.6.1.4.1.123.2.10.1.1.7
What kind of 'sub-module' is present in the specified position. If the value of this object does not match the value of the nnciSlotModuleProgType object, the position will be held out of service.
Status: mandatory	Access: read-only
OBJECT-TYPE
	SubModuleType

nnciSlotFirmwareID		1.3.6.1.4.1.123.2.10.1.1.8
The revision level of the firmware, if any, that is present on a module. If no firmware is present, the value will be zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciSlotBusyOut		1.3.6.1.4.1.123.2.10.1.1.9
This object is used to take circuits on a specified slot out of service. If the value of this object is hold-out-of-service, then the circuits on the slot will not be used even if all alarms are cleared and the circuits would normally be placed into service. If the value of this object is normal, then the circuits will operate as if this object did not exist. If the circuits are the specified position are in service when the object is set, it will be immediately removed from service.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), hold-out-of-service(2)

nnciSlotSubModuleID		1.3.6.1.4.1.123.2.10.1.1.10
The hardware identification number assigned to the sub-module that is present in the specified position. If there is no sub-module installed in the position, or no sub-module present, the value returned will be zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	SubModuleID

nnciSlotVariantID		1.3.6.1.4.1.123.2.10.1.1.14
The variant identification number for the module which is installed in the specified slot. If there is no module installed, the value returned will be zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciSlotResetCard		1.3.6.1.4.1.123.2.10.1.1.15
This object is used to cause the node to re-initialize the specified module. Any set to this object will cause the specified module to be re-initialized. If a set is attempted with the modifier set to select the main card, the whole node will be reset. A get on this object will always return zero.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciSlotHardwareRevision		1.3.6.1.4.1.123.2.10.1.1.19
The engineering revision level of the module that occupies the specified position. The high nibble of the returned value is the major revision level and the low nibble is the minor revision, e.g. Engineering Revision 21 will be returned as $21.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciT1SlotTable		1.3.6.1.4.1.123.2.22.1
This table contains all of the configuration and status information for a T1 interface.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciT1SlotTableEntry

nnciT1SlotTableEntry		1.3.6.1.4.1.123.2.22.1.1
A list of all of the configuration and status information for a T1 interface.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciT1SlotTableEntry

nnciT1SlotAlarmControl		1.3.6.1.4.1.123.2.22.1.1.1
This object can be used to control the alarm condition that is indicated by the specified interface. If ForceYellow is selected, the interface will provide the same indication to the far end as if the local interface had lost frame. If ForceAIS is selected, the interface will transmit an unframed all ones signal towards the far end.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noAlarm(1), forceYellow(2), forceAIS(3)

nnciT1SlotFramingStyle		1.3.6.1.4.1.123.2.22.1.1.2
This object is used to select either D4 or ESF framing for the T1 link.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	d4Framing(1), esfFraming(2)

nnciT1SlotZeroSuppression		1.3.6.1.4.1.123.2.22.1.1.3
This object is used to select the kind, if any, of zero-code suppression to be used on the link.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), b8zs(2), jamBit7(3)

nnciT1SlotLinkStatus		1.3.6.1.4.1.123.2.22.1.1.7
This object returns the current 'alarm' state of the T1 facility.
Status: mandatory	Access: read-only
OBJECT-TYPE
	T1E1Status

nnciT1SlotLoopLength		1.3.6.1.4.1.123.2.22.1.1.8
This object is used to control the pre-equalization applied to signal before transmission.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	short(1), medium(2), long(3)

nnciT1SlotThreshold		1.3.6.1.4.1.123.2.22.1.1.9
This object controls the system's tolerance of failures on the specified T1 link. If more than the specified number of failures occurs in one hour, the interface will be removed from consideration as a source of synchronization. A failure is defined as the occurrence of an alarm condition on the interface, i.e. one that results in any bits other than 0 (zero) or 9 (nine) being set in the nnciT1SlotLinkStatus object.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciT1SlotLoopback		1.3.6.1.4.1.123.2.22.1.1.11
This object is used to set or remove loopbacks on the T1 link
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), equipment(2), equipment-all-ones(3), equipment-digital(4), line(5), line-and-equipment(6)

nnciT1SlotTrunkConditioningEnable		1.3.6.1.4.1.123.2.22.1.1.16
This object controls when trunk-conditioning is applied to the specified T1 link. Trunk- conditioning is the process by which all of the connections to the link are temporarily broken and a known pattern is sent on each channel of the T1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciT1SlotAlarmDeclarationTime		1.3.6.1.4.1.123.2.22.1.1.17
This object controls the interval for which the local loss-of-frame condition is debounced. The debounce algorithm and default value correspond to the requirements of AT&T PUB 62411.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciT1SlotAlarmClearingTime		1.3.6.1.4.1.123.2.22.1.1.18
This object controls the interval for which the reacquisition of local frame is debounced. The debounce algorithm and default value correspond to the requirements of AT&T PUB 62411.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciT1SlotCRCFraming		1.3.6.1.4.1.123.2.22.1.1.20
This object controls whether a Cyclic Redundancy Check is used when the specified T1 link reframes. This is only applicable to T1 links that a programmed for ESF operation.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

nnciE1SlotTable		1.3.6.1.4.1.123.2.20.1
This table contains all of the configuration and status information for a E1 interface
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciE1SlotTableEntry

nnciE1SlotTableEntry		1.3.6.1.4.1.123.2.20.1.1
A list of all of the configuration and status information for a E1 interface.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciE1SlotTableEntry

nnciE1SlotAlarmControl		1.3.6.1.4.1.123.2.20.1.1.1
This object can be used to control the alarm condition that is indicated by the specified interface. If ForceAISInTS16 is selected, the interface will transmit a continuous all ones pattern in TS16 of the E1 link. If ForceAISAllTS is selected, the interface will transmit an un-framed 'all ones' signal on the interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	nonalarm(1), forceAISInTS16(2), forceAISInA11TS(3)

nnciE1SlotLoopback		1.3.6.1.4.1.123.2.20.1.1.4
This object is used to set or remove loopbacks on the E1 interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), equipment(2), equipment-all-ones(3), equipment-digital(4), line(5), line-and-equipment(6)

nnciE1SlotSignalling		1.3.6.1.4.1.123.2.20.1.1.7
This object is used to select either Common Channel Signalling (CCS) or Channel Associated Signalling (CAS) operation for the interface. CCS operation makes timeslot 16 of the E1 link available for user data . 31CHAN mode allows TS16 to be used for super-rate data, whereas CCS does not. In CAS operation, timeslot 16 is used to transfer ABCD bit signalling and thus is not available to carry user data.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	cas(1), ccs(2), thirtyOneChan(3)

nnciE1SlotShieldLevel		1.3.6.1.4.1.123.2.20.1.1.9
This object is used to control the level of the coax shield at the E1 physical interface for each of the receive and transmit lines. The two shields (receive and transmit) can be controlled independently.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	both-grounded(1), onlyRX-grounded(2), onlyTX-grounded(3), neither-grounded(4)

nnciE1SlotLinkStatus		1.3.6.1.4.1.123.2.20.1.1.11
This object returns the current 'alarm' state of the E1 interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	T1E1Status

nnciE1SlotThreshold		1.3.6.1.4.1.123.2.20.1.1.12
This object controls the system's tolerance of failures on the specified interface. If more than the specified number of failures occurs in one hour, the interface will be removed from consideration as a source of synchronization. A failure is defined as the occurrence of an alarm condition on the interface, i.e. one that results in any bits other than 0 (zero) or 9 (nine) being set in the nnciE1SlotLinkStatus object.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciE1TypeOfStats		1.3.6.1.4.1.123.2.20.1.1.14
The type of stats to be collected for this E1 link.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	hdb3(1), crc4(2)

nnciE1SlotTrunkConditioningEnable		1.3.6.1.4.1.123.2.20.1.1.21
This object controls when trunk-conditioning is applied to the specified interface. Trunk- conditioning is the process by which all of the connections to the interface are temporarily broken and a known pattern is sent on each channel of the interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciE1SlotAlarmDeclarationTime		1.3.6.1.4.1.123.2.20.1.1.22
This object controls the interval for which the local loss-of-frame condition is debounced.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciE1SlotAlarmClearingTime		1.3.6.1.4.1.123.2.20.1.1.23
This object controls the interval for which the reacquisition of local frame is debounced.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciE1SlotCRCFraming		1.3.6.1.4.1.123.2.20.1.1.25
This object controls the generation and use of a Cyclic Redundancy Check during reframing.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

nnciDevTable		1.3.6.1.4.1.123.2.11.1
This table contains all of the common, per-device configuration and status information for a circuit. Device-type specific information is found in other tables as appropriate.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciDevTableEntry

nnciDevTableEntry		1.3.6.1.4.1.123.2.11.1.1
A list of all of the common, per-device configuration and status information.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciDevTableEntry

nnciDevName		1.3.6.1.4.1.123.2.11.1.1.2
A user-defined name for the specified circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

nnciDevLoopback		1.3.6.1.4.1.123.2.11.1.1.4
This object is used to apply and remove loopbacks on the specified circuit. Note that it may not be possible to apply loopbacks to some circuit types.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), lpbkA(2), lpbkB(3), lpbkC(4)

nnciDevMateDevice		1.3.6.1.4.1.123.2.11.1.1.5
The device number of the device, if any, that is cross-connected to the device of interest. If there is no programmed connection, the device number will be zero.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DeviceNumber

nnciDevSetShowSig		1.3.6.1.4.1.123.2.11.1.1.10
A get from this object will return the current value of signalling, as appropriate for the type of the specified device. When set, the bit pattern supplied will be used as the signalling that is being sent by the circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciDevReady		1.3.6.1.4.1.123.2.11.1.1.15
Whether or not the circuit is ready for use.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notReady(0), ready(1)

nnciDevActive		1.3.6.1.4.1.123.2.11.1.1.16
Whether or not the circuit is active.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notActive(0), active(1)

nnciDevConnected		1.3.6.1.4.1.123.2.11.1.1.17
Whether or not the circuit is connected.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notConnected(0), connected(1)

nnciDevOutOfService		1.3.6.1.4.1.123.2.11.1.1.18
Whether or not the circuit has detected an OutOfService condition.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	inService(0), outOfService(1)

nnciDevUnderMaintenance		1.3.6.1.4.1.123.2.11.1.1.21
True iff the circuit has been subject to a maintenance operation, e.g. a loopback.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noMaint(0), underMaint(1)

nnciDevBusyOut		1.3.6.1.4.1.123.2.11.1.1.22
This object is used to remove a circuit from service.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	notBusy(0), busiedOut(1)

nnciDevFailed		1.3.6.1.4.1.123.2.11.1.1.23
True iff this circuit has failed a diagnostics test.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	notFailed(0), failed(1)

nnciDevDiagEnable		1.3.6.1.4.1.123.2.11.1.1.24
Whether or not background diagnostics are enabled for this circuit (if applicable).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	diagDisabled(0), diagEnabled(1)

nnciT1Table		1.3.6.1.4.1.123.2.23.1
This table contains all of the configuration and status information for a T1 circuit
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciT1TableEntry

nnciT1TableEntry		1.3.6.1.4.1.123.2.23.1.1
A list of all of the configuration and status information for an T1 circuit
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciT1TableEntry

nnciT1BusyOut		1.3.6.1.4.1.123.2.23.1.1.1
What action will be taken on the circuit when the circuit is not connected.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	idle(1), seized(2), oosA(3), oosB(4)

nnciT1RobbedBitSig		1.3.6.1.4.1.123.2.23.1.1.4
This object is used to enable or disable Robbed-Bit Signalling for the circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	rbsOn(1), rbsOff(2)

nnciT1Inversion		1.3.6.1.4.1.123.2.23.1.1.5
Whether or not data transmitted on this circuit is inverted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	invertOn(1), invertOff(2)

nnciT1DefaultData		1.3.6.1.4.1.123.2.23.1.1.8
The value that is to be transmitted on the circuit when it is not connected.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OneByte

nnciT1FirstCode		1.3.6.1.4.1.123.2.23.1.1.9
The nnciT1FirstCode object is one of two which determines the signalling that will be sent during the Trunk-Conditioning process. This object determines the signalling that will be sent during a timed-break, if one is applied.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..15

nnciT1SecondCode		1.3.6.1.4.1.123.2.23.1.1.10
The nnciT1SecondCode object is the second of two objects which determines the signalling that will be sent during the Trunk-Conditioning process. This object determines the signalling that will be sent for the duration of the trunk-conditioning process, following the timed-break.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..15

nnciT1PartOfSuperRate		1.3.6.1.4.1.123.2.23.1.1.12
This parameter is used to form a circular linked list of circuit numbers which make up a superrate connection It contains the circuit number of the next circuit in the superrate connection or zero if the circuit is not part of a super-rate group
Status: mandatory	Access: read-write
OBJECT-TYPE
	CircuitNumber

nnciT1BitsUsed		1.3.6.1.4.1.123.2.23.1.1.13
A bitmap which indicates which bits of the T1 circuit are to be used for data.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

nnciT1SuperRateCircuitMap		1.3.6.1.4.1.123.2.23.1.1.20
When written to, this object builds the circularly-linked list of circuits represented by the one bits in the value written. When read, this object returns the bit map corresponding to the super-rate group of which this circuit is a member
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciT1SuperRateNumCircuits		1.3.6.1.4.1.123.2.23.1.1.21
When written to, this object builds the circularly-linked list of circuits to represent the super-rate group which begins at this circuit and contains the specified number of circuits. When read, this object returns the number of circuits in the super-rate group of which this circuit is a member
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciE1Table		1.3.6.1.4.1.123.2.21.1
This table contains all of the configuration and status information for a E1 circuit
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciE1TableEntry

nnciE1TableEntry		1.3.6.1.4.1.123.2.21.1.1
A list of all of the configuration and status information for an E1 circuit
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciE1TableEntry

nnciE1BusyOut		1.3.6.1.4.1.123.2.21.1.1.3
What signalling will be transmitted on the circuit when the circuit is not connected.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	idle(1), seized(2), oosA(3), oosB(4)

nnciE1AlternateDigitInversion		1.3.6.1.4.1.123.2.21.1.1.6
Whether or not Alternate Digit Inversion (ADI) will be applied to the data transmitted and received on the circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	adiOn(1), adiOff(2)

nnciE1DefaultData		1.3.6.1.4.1.123.2.21.1.1.9
The value that is to be transmitted on the circuit when it is not connected.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OneByte

nnciE1FirstCode		1.3.6.1.4.1.123.2.21.1.1.10
The nnciE1FirstCode object is one of two which determines the signalling that will be sent during the Trunk-Conditioning process. This object determines the signalling that will be sent during a timed-break, if one is applied.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..15

nnciE1SecondCode		1.3.6.1.4.1.123.2.21.1.1.11
The nnciE1SecondCode object is the second of two objects which determines the signalling that will be sent during the Trunk-Conditioning process. This object determines the signalling that will be sent for the duration of the trunk-conditioning process, following the timed-break.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..15

nnciE1PartOfSuperRate		1.3.6.1.4.1.123.2.21.1.1.13
This parameter is used to form a circular linked list of circuit numbers which make up a superrate connection. It contains the circuit number of the next circuit in the superrate connection or zero if the circuit is not part of a super-rate group.
Status: mandatory	Access: read-write
OBJECT-TYPE
	CircuitNumber

nnciE1BitsUsed		1.3.6.1.4.1.123.2.21.1.1.14
A bitmap which indicates which bits of the E1 circuit are to be used for data.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

nnciE1SuperRateCircuitMap		1.3.6.1.4.1.123.2.21.1.1.21
When written to, this object builds the circularly-linked list of circuits represented by the one bits in the value written. When read, this object returns the bit map corresponding to the super-rate group of which this circuit is a member
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciE1SuperRateNumCircuits		1.3.6.1.4.1.123.2.21.1.1.22
When written to, this object builds the circularly-linked list of circuits to represent the super-rate group which begins at this circuit and contains the specified number of circuits. When read, this object returns the number of circuits in the super-rate group of which this circuit is a member.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciSdcTable		1.3.6.1.4.1.123.2.72.1
This table contains all of the configuration and status information for a Synchronous Data Module circuit.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciSdcTableEntry

nnciSdcTableEntry		1.3.6.1.4.1.123.2.72.1.1
A list of all of the configuration and status information required for a Synchronous Data Module circuit.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciSdcTableEntry

nnciSdcInterfaceControl		1.3.6.1.4.1.123.2.72.1.1.1
Determines the gender (DTE/DCE) of the specified circuit. The gender is used to a) control the operation and interpretation of the control leads and determine the source of clocks for the interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dce(0), dte(16)

nnciSdcInterfaceSpeed		1.3.6.1.4.1.123.2.72.1.1.2
This object determines the speed of the specified interface in multiples of 800 bits/s. When the interface is in Data Terminal Equipment (DTE) mode (see nnciSdcInterfaceControl), the interface will run at the speed of the supplied clocks, regardless of the value of this object.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciSdcLeadsDefaultOn		1.3.6.1.4.1.123.2.72.1.1.3
This controls the state of the control leads on the specified interface. The control leads that are affected by this object are determined by a) the type of the interface and b) the mode (or gender) of the interface. The leads specified by this object are asserted towards the attached equipment. If there is a conflict between the leads that are 'defaulted on' and those that are 'defaulted off', the value of this object is taken to be correct.
Status: mandatory	Access: read-write
OBJECT-TYPE
	ControlLeads

nnciSdcLeadDefaultOff		1.3.6.1.4.1.123.2.72.1.1.4
The interface control leads specified by this object are de-asserted towards the attached equipment.
Status: mandatory	Access: read-write
OBJECT-TYPE
	ControlLeads

nnciSdcInterfaceStatus		1.3.6.1.4.1.123.2.72.1.1.5
This object reports the current status of the control leads associated with the specified interface. The meanings of the bits reported by this object depend on the type and gender of the interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	ControlLeads

nnciHdlcTable		1.3.6.1.4.1.123.2.66.1
This table contains all of the configuration, status and statistical information required for an HDLC circuit.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciHdlcTableEntry

nnciHdlcTableEntry		1.3.6.1.4.1.123.2.66.1.1
A list of all of the configuration, status and statistical information required for an HDLC circuit.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciHdlcTableEntry

nnciHdlcBytesTransmitted		1.3.6.1.4.1.123.2.66.1.1.1
A count of data and padding bytes that were successfully transmitted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedCounter

nnciHdlcFramesTransmitted		1.3.6.1.4.1.123.2.66.1.1.2
The number of frames that were successfully transmitted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedCounter

nnciHdlcRxGoodBytes		1.3.6.1.4.1.123.2.66.1.1.3
The number of bytes in frames that were successfully received.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedCounter

nnciHdlcRxGoodFrames		1.3.6.1.4.1.123.2.66.1.1.4
The number of frames that were successfully received.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedCounter

nnciHdlcUnderrun		1.3.6.1.4.1.123.2.66.1.1.5
The number of frames that should have been transmitted by the station, but could not be transmitted due to an internal MAC sublayer transmit error.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedCounter

nnciHdlcCRCError		1.3.6.1.4.1.123.2.66.1.1.6
The number of frames that contained an integral number of bytes but did not pass the frame sequence.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedCounter

nnciHdlcAlignmentError		1.3.6.1.4.1.123.2.66.1.1.7
The number of frames that did not contain an integral number of bytes and did not pass the frame sequence.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedCounter

nnciHdlcOverrun		1.3.6.1.4.1.123.2.66.1.1.8
The number of frames which should have been received by the station, but could not be accepted due to an internal MAC sublayer receive error.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedCounter

nnciHdlcAbort		1.3.6.1.4.1.123.2.66.1.1.9
The number of the number of times that a minimum of seven consecutive ones was received during frame reception.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedCounter

nnciHdlcSinceLastReset		1.3.6.1.4.1.123.2.66.1.1.11
This object indicates the elapsed time in hundredths of a second since the HDLC device's statistical counters were last reset.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedTime

nnciHdlcApplication		1.3.6.1.4.1.123.2.66.1.1.12
This object indicates the elapsed time in hundredths of a second since the HDLC device's statistical counters were last reset.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), cpss(1), bridge(2), frameStream(3)

nnciBridgeTable		1.3.6.1.4.1.123.2.55.1
This table contains all of the configuration information for a Bridge.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciBridgeTableEntry

nnciBridgeTableEntry		1.3.6.1.4.1.123.2.55.1.1
A list of all of the configuration information required for a Bridge.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciBridgeTableEntry

nnciBrdgAddress		1.3.6.1.4.1.123.2.55.1.1.3
The data-link layer address to which messages destined for the bridge should be sent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	PhysAddress

nnciBrdgUptime		1.3.6.1.4.1.123.2.55.1.1.4
The elapsed time in hundredths of a second since the bridge entity was last reset.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedTime

nnciBrdgInterfaceCount		1.3.6.1.4.1.123.2.55.1.1.5
The number of interfaces which are programmed to be used for/by the bridge.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciBrdgMaxInterfaceCount		1.3.6.1.4.1.123.2.55.1.1.6
The maximum possible number of interfaces supported by the bridge.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciBrdgMapCircuitToInterface		1.3.6.1.4.1.123.2.55.1.1.7
Which interface the specified device belongs to.
Status: mandatory	Access: read-only
OBJECT-TYPE
	InterfaceIndex

nnciBridgeStPhase1		1.3.6.1.4.1.123.2.61.1
OBJECT IDENTIFIER

nnciBridgeStPhase1GroupOne		1.3.6.1.4.1.123.2.61.1.1
OBJECT IDENTIFIER

nnciBrdgStFramesFiltered		1.3.6.1.4.1.123.2.61.1.1.4
The number of frames received by the bridge and discarded based on information in the address filter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedCounter

nnciBrdgStFramesForwarded		1.3.6.1.4.1.123.2.61.1.1.5
The number of frames received by the bridge, not discarded and forwarded to a single destination.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedCounter

nnciBrdgStFramesFlooded		1.3.6.1.4.1.123.2.61.1.1.6
The number of frames received by the bridge, not discarded, but re-transmitted on all interfaces
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedCounter

nnciBrdgStTimeSinceLastReset		1.3.6.1.4.1.123.2.61.1.1.11
The elapsed time in hundredths of a second since the bridge's statistical counters were last reset.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedTime

nnciFilterTable		1.3.6.1.4.1.123.2.62.1
This table contains all of the configuration and status information related to the filtering mechanism of a Transparent Bridge.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciFilterTableEntry

nnciFilterTableEntry		1.3.6.1.4.1.123.2.62.1.1
A list of all of the configuration and status information related to the filtering mechanism of a Transparent Bridge.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciFilterTableEntry

nnciFilterReset		1.3.6.1.4.1.123.2.62.1.1.1
This object forces the bridge to reset the filtering database by first removing all of the entries from the filter and then re-initializing it with the entries from the permanent database. A get on this object will always return zero
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	nop(0), reset(1)

nnciFilterLearn		1.3.6.1.4.1.123.2.62.1.1.2
This object determines whether the address filter will learn the source addresses of frames transmitted on networks to which it is directly attached.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	doNotLearn(0), learn(1)

nnciFilterPermDBChange		1.3.6.1.4.1.123.2.62.1.1.4
This object indicates that the permanent database entries have changed since the last filter reset.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	same-as-before(0), changed(1)

nnciFilterPermDBMaxEntries		1.3.6.1.4.1.123.2.62.1.1.5
This object indicates the maximum number of entries that may be placed in the permanent database of the bridge.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciFilterPermDBEntryCount		1.3.6.1.4.1.123.2.62.1.1.6
This object returns the number of entries currently in the permanent database.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciFilterPermDBContents		1.3.6.1.4.1.123.2.62.1.1.7
This object provides access to the contents of the permanent database. The modifier is the entry number which can range from 1 to FILTER-PermDBEntryCount. If an attempt is made to access an entry that is not defined, an error will be returned.
Status: mandatory	Access: read-only
OBJECT-TYPE
	FilterEntry

nnciFilterAddPermDBEntry		1.3.6.1.4.1.123.2.62.1.1.8
This object provides a way to add an entry to the permanent database of the bridge. If the maximum size of the permanent database is exceeded, an error will be returned.
Status: mandatory	Access: read-write
OBJECT-TYPE
	FilterEntry

nnciFilterDeletePermDBEntry		1.3.6.1.4.1.123.2.62.1.1.9
This object provides a way to delete an entry from the permanent database of the bridge. If the specified entry does not exist, an error will be returned.
Status: mandatory	Access: read-write
OBJECT-TYPE
	FilterEntry

nnciFilterAFMaxEntries		1.3.6.1.4.1.123.2.62.1.1.10
This object stores the maximum number of entries that may be placed in the address filter. The number includes both entries copied from the permanent database and learned entries.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciFilterAFEntryLifetime		1.3.6.1.4.1.123.2.62.1.1.11
This object determined the lifetime of an entry in the address filter. Any entry that is present in the filter but not repeated within n nnciFilterAFEntryLifetime will be deleted from the filter. If the Spanning Tree Protocol is used, TBD this value of STP-ForwardDelay used to age the filter entries.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciFilterAFEntryCount		1.3.6.1.4.1.123.2.62.1.1.12
This object returns the number of entries currently in the address filter. This can be used in conjunction with nnciFilterAFContents to obtain the current contents of the address filter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciFilterAFContents		1.3.6.1.4.1.123.2.62.1.1.13
This object provides access tot he current contents of the address filter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	FilterEntry

nnciFilterForwardMatrix		1.3.6.1.4.1.123.2.62.1.1.14
This object determines any restrictions on bridged traffic flow from a particular interface to all of the other interfaces. The restrictions are organized as a bit vector where the values are either permit or deny. The value of nnciFilterForwardMatrix [i,j] must be permit if any frame originating on interface i may be transmitted on interface j.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciFilterFloodUnicastMatrix		1.3.6.1.4.1.123.2.62.1.1.15
This object determines the handling of a unicast frame with an unrecognized destination. The bridge normally floods such frames on all interfaces except the one on which the frame was received. This object can be used to prevent frames being flooded onto specific interfaces. The restrictions are organized as a bit vector for each interface, where the values are either permit or deny.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciFilterTakeSnapShot		1.3.6.1.4.1.123.2.62.1.1.17
A set with a value of snapshot will make a copy of the address filter that can be accessed by gets from nnciFilterContents
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	nop(0), snapshot(1)

nnciFilterFloodMulticastMatrix		1.3.6.1.4.1.123.2.62.1.1.18
This object determines the handling of a multicast frame with an unrecognized destination. The bridge normally floods such frames on all interfaces except the one on which the frame was received. This object can be used to prevent frames being flooded onto specific interfaces. The restrictions are organized as a bit vector for each interface, where the values are either permit or deny.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciFilterFloodBroadcastMatrix		1.3.6.1.4.1.123.2.62.1.1.19
This object determines the handling of a broadcast frame with an unrecognized destination. The bridge normally floods such frames on all interfaces except the one on which the frame was received. This object can be used to prevent frames being flooded onto specific interfaces. The restrictions are organized as a bit vector for each interface, where the values are either permit or deny.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciFilterPermNVDBContents		1.3.6.1.4.1.123.2.62.1.1.20
This object provides access to the permanent entries stored in NVM, it is used to provide a degree of indirection through the permanent entry vector necessary for minimal manipulation of the database during deletion of permanent entries.
Status: mandatory	Access: read-only
OBJECT-TYPE
	FilterEntry

nnciFilterDeleteAllPermEntries		1.3.6.1.4.1.123.2.62.1.1.21
This object provides a way to delete all permanent entries from the database in one operation.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciStpTable		1.3.6.1.4.1.123.2.63.1
This table contains all of the configuration and status information relating to the operation of the 802.1d Spanning Tree Protocol.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NnciStpTableEntry

nnciStpTableEntry		1.3.6.1.4.1.123.2.63.1.1
A list of all of the configuration and status information relating to the operation of the 802.1d Spanning Tree Protocol.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NnciStpTableEntry

nnciStpEnable		1.3.6.1.4.1.123.2.63.1.1.1
This object enables or disables the Spanning Tree Protocol. If the protocol is disabled, the bridge acts as a simple bridge, which routes packets based only on information in the address filter. Working without the Spanning Tree Protocol may lead to loops in the network topology and is not recommended. The remaining objects in this section are only defined when the Spanning Tree Protocol is enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	stpOff(0), stpOn(1)

nnciStpBridgePriority		1.3.6.1.4.1.123.2.63.1.1.2
This object determines the role of the bridge in the spanning tree. It is used to decide which bridge in the network should be the root, which bridges should be active, and which bridges should operate in a standby mode. By changing the bridge priority, one can affect the configuration of the spanning tree. Bridges with smaller priority values are preferentially active i.e. smaller values indicate higher priorities. The bridge priority forms the upper two bytes of the bridge identifier used by the Spanning Tree Protocol.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciStpRoot		1.3.6.1.4.1.123.2.63.1.1.3
This object identifies the bridge that is the root of the spanning tree.
Status: mandatory	Access: read-only
OBJECT-TYPE
	BridgeIdentifier

nnciStpRootPathCost		1.3.6.1.4.1.123.2.63.1.1.4
This cost of a path is the sum of the costs of the individual hops along the path to the root, where the cost of a hop is a user-assignable object usually related to the speed of the physical link (speed in Mbits/sec) - see also nnciStpInterfaceCost.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciStpRootInterface		1.3.6.1.4.1.123.2.63.1.1.5
This object indicates the interface currently used to send messages to the root bridge. It is chosen as the interface which provides the least-cost path to the root.
Status: mandatory	Access: read-only
OBJECT-TYPE
	InterfaceIndex

nnciStpMaxAge		1.3.6.1.4.1.123.2.63.1.1.6
This object defines the maximum permissible age in seconds of the configuration information held for each interface. If the information becomes older than nnciStpMaxAge, without being updated by another configuration message from the root bridge, it is discarded, and the bridge attempts to become the designated bridge for that link. In this way, failures of the root or other bridges are detected. (See also nnciStpMyMaxAge).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciStpHelloTime		1.3.6.1.4.1.123.2.63.1.1.7
This object is the value of the HelloTimer used by the root bridge. The present Spanning Tree protocol propogates this value, but the bridges never use it; they use nnciStpMyHelloTime instead.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciStpForwardDelay		1.3.6.1.4.1.123.2.63.1.1.8
This object defines the number of seconds that an interface is kept in the listening or learning state before being moved to the next state. If a topology change has been detected (i.e., nnciStpTopologyChange is true), then this value is also used as the maximum lifetime of entries in the address filter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciStpMyMaxAge		1.3.6.1.4.1.123.2.63.1.1.9
This object is assigned to nnciStpMaxAge if this bridge becomes the root of the spanning tree.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciStpMyHelloTime		1.3.6.1.4.1.123.2.63.1.1.10
This object is the interval between transmission of configuration BPDUs (also called Hello messages) by the bridge. This object is also assigned to nnciStpHelloTime if this bridge becomes the root of the Spanning Tree.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciStpMyForwardDelay		1.3.6.1.4.1.123.2.63.1.1.11
This object is assigned to nnciStpForwardDelay if this bridge becomes the root of the Spanning Tree.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciStpTopologyChangeDetected		1.3.6.1.4.1.123.2.63.1.1.12
If this object is true, then this bridge has detected a topology change recently and is sending topology change notifications (TCNs) to the root bridge.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	no(0), yes(1)

nnciStpSendingTopologyChange		1.3.6.1.4.1.123.2.63.1.1.13
If this object is true, then the bridge has recently received a configuration BPDU with the topology change flag set. This indicates that the bridge has been notified (or has itself detected) a topology change, and all bridges in the network should use nnciStpForwardDelay as the aging time of entries in the filtering database for as long as the flag is set.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	no(0), yes(1)

nnciStpTimeSinceLastTopologyChange		1.3.6.1.4.1.123.2.63.1.1.14
This object provides the elapsed time in seconds since the last change in network topology. This object is set to zero when a bridge reset occurs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ExtendedTime

nnciStpTopologyChanges		1.3.6.1.4.1.123.2.63.1.1.15
This object indicates the number of times that the topology change flag has been set to true since the last bridge reset.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

nnciStpTopologyChangeAck		1.3.6.1.4.1.123.2.63.1.1.16
This flag indicates whether the topology change acknowledge flag should be set in the next hello message generated on this interface. Setting this flag acknowledges the receipt of a topology change notification (TCN) from another bridge on the interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	no(0), yes(1)

nnciStpInterfacePriority		1.3.6.1.4.1.123.2.63.1.1.17
This object is a user-settable priority assigned to each interface. The interface priority allows the network manager to indicate that a given interface should be preferentially used for forwarding messages. Interfaces with smaller numbers (higher priorities) are preferentially used for bridge traffic.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciStpInterfaceCost		1.3.6.1.4.1.123.2.63.1.1.18
This object indicates the relative cost of sending a frame out on a given interface. It is computed in the following manner. If nnciStpCostMultiplier is non-zero, then nnciStpInterfaceCost = (nnciStpCostMultiplier/100) * (10^9 / ifSpeed). If nnciStpCostMultiplier is zero, then nnciStpInterfaceCost = nnciStpUserAssignedCost. In this way, the cost of an interface can either track the bandwidth allocated, or be assigned a fixed value. Note that the value is not allowed to be zero.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciStpDesignatedBridge		1.3.6.1.4.1.123.2.63.1.1.19
This object specifies the designated bridge for the link (LAN or WAN) attached to the interface. Specifically, it is the id of the designated bridge. The designated bridge for a link is chosen as the bridge with the least-cost path to the root.
Status: mandatory	Access: read-only
OBJECT-TYPE
	BridgeIdentifier

nnciStpDesignatedInterface		1.3.6.1.4.1.123.2.63.1.1.20
This object indicates the interface that the bridge given by nnciStpDesignatedBridge uses to send configuration messages over the link (LAN or WAN). Specifically, it is the id of the interface (i.e., the concatenation of the interface priority and the interface address). This object is of interest if the designated bridge has more than one interface connected to the link.
Status: mandatory	Access: read-only
OBJECT-TYPE
	InterfaceIndex

nnciStpDesignatedRoot		1.3.6.1.4.1.123.2.63.1.1.21
This object indicates who the designated bridge thinks is the root (i.e., what the value of nnciStpRoot is on the bridge given by nnciStpDesignateBridge). This object will only differ from nnciStpRoot when the topology of the spanning tree is changing.
Status: mandatory	Access: read-only
OBJECT-TYPE
	BridgeIdentifier

nnciStpDesignatedCost		1.3.6.1.4.1.123.2.63.1.1.22
This object provides the cost of the cheapest path between nnciStpDesignatedBridge and nnciStpDesignatedRoot.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

nnciStpConfigurationMessagePending		1.3.6.1.4.1.123.2.63.1.1.23
If this object is true, then a configuration BPDU has been queued for transmission due to the transmission of another configuration BPDU within the last second.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	no(0), yes(1)

nnciStpAllowableDeviations		1.3.6.1.4.1.123.2.63.1.1.24
This object specifies those deviations from the 802.1d document that will be tolerated by the bridge. If the bit in the specified position is 1, then that deviation will be allowed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciStpCostMultiplier		1.3.6.1.4.1.123.2.63.1.1.25
This object is the weight assigned to the default cost, expressed as a percentage. That is, a multiplier of 50 means the interface should have half its default cost as determined by its speed. See the description of nnciStpInterfaceCost for more details.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

nnciStpUserAssignedCost		1.3.6.1.4.1.123.2.63.1.1.26
This object is used to determine the cost assigned to a interface. See the description of nnciStpInterfaceCost for the details.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER