NQA-MIB

File: NQA-MIB.mib (378361 bytes)

Imported modules

RFC1155-SMI IF-MIB HUAWEI-MIB
INET-ADDRESS-MIB SNMPv2-CONF SNMPv2-SMI
SNMPv2-TC SNMP-FRAMEWORK-MIB IEEE802171-CFM-MIB
P-BRIDGE-MIB Q-BRIDGE-MIB HUAWEI-ETHOAM-MIB

Imported symbols

IpAddress InterfaceIndexOrZero hwDatacomm
InetAddressType InetAddress InetPortNumber
OBJECT-GROUP MODULE-COMPLIANCE TimeTicks
Integer32 Gauge32 Counter32
Unsigned32 OBJECT-TYPE mib-2
NOTIFICATION-TYPE NOTIFICATION-GROUP MODULE-IDENTITY
DisplayString TruthValue TimeStamp
RowStatus TimeInterval StorageType
MacAddress DateAndTime TEXTUAL-CONVENTION
SnmpAdminString Dot1agCfmMepIdOrZero Dot1agCfmMaintDomainName
Dot1agCfmMaintAssocName EnabledStatus VlanIdOrNone
HWDot1agCfmRelayActionFieldValue HWDot1agCfmIngressActionFieldValue HWDot1agCfmEgressActionFieldValue

Defined Types

NqaType  
Select test type
TEXTUAL-CONVENTION    
  INTEGER unknown(0), tcpConnect(1), udpEcho(2), httpAppl(3), ftpAppl(4), jitterAppl(5), icmpAppl(6), snmpAppl(7), traceRoute(8), lspPing(9), lspTraceRoute(10), dnsAppl(11), dhcpAppl(12), dlswAppl(13), pwe3Ping(14), pwe3Tracert(15), mPing(16), mTracert(17), macPing(18), macTunnelPing(19), lspJitter(20), pathMtu(21), icmpJitter(22), pathJitter(23), pppoe(24), vplsmPing(25), vplsmacPing(26), vplsmacTrace(27), vplsMTrace(28), gmacping(29), gmactrace(30), mactrace(31), vplspwping(32), vplspwtrace(33)  

EnableValue  
Represents a boolean value.
TEXTUAL-CONVENTION    
  INTEGER enable(1), disable(2)  

NqaDistanceNodeType  
Selection of destination addresses when MACPing is performed.
TEXTUAL-CONVENTION    
  INTEGER macAddress(1), mepID(2)  

HWLldpPortIdSubtype  
LLDP interface ID sub type
TEXTUAL-CONVENTION    
  INTEGER interfaceAlias(1), portComponent(2), macAddress(3), networkAddress(4), interfaceName(5), agentCircuitId(6), local(7)  

HWLldpPortId  
This TC describes the format of a port identifier string. Objects of this type are always used with an associated LldpPortIdSubtype object, which identifies the format of the particular LldpPortId object instance. If the associated LldpPortIdSubtype object has a value of 'interfaceAlias(1)', then the octet string identifies a particular instance of the ifAlias object (defined in IETF RFC 2863). If the particular ifAlias object does not contain any values, another port identifier type should be used. If the associated LldpPortIdSubtype object has a value of 'portComponent(2)', then the octet string identifies a particular instance of the entPhysicalAlias object (defined in IETF RFC 2737) for a port or backplane component. If the associated LldpPortIdSubtype object has a value of 'macAddress(3)', then this string identifies a particular unicast source address (encoded in network byte order and IEEE 802.3 canonical bit order) associated with the port (IEEE Std 802-2001). If the associated LldpPortIdSubtype object has a value of 'networkAddress(4)', then this string identifies a network address associated with the port. The first octet contains the IANA AddressFamilyNumbers enumeration value for the specific address type, and octets 2 through N contain the networkAddress address value in network byte order. If the associated LldpPortIdSubtype object has a value of 'interfaceName(5)', then the octet string identifies a particular instance of the ifName object (defined in IETF RFC 2863). If the particular ifName object does not contain any values, another port identifier type should be used. If the associated LldpPortIdSubtype object has a value of 'agentCircuitId(6)', then this string identifies a agent-local identifier of the circuit (defined in RFC 3046). If the associated LldpPortIdSubtype object has a value of 'local(7)', then this string identifies a locally assigned port ID.
TEXTUAL-CONVENTION    
  OCTET STRING Size(1..255)  

NqaOperation  
Paras for specified test.
TEXTUAL-CONVENTION    
  INTEGER noOperation(1), httpGet(2), httpPost(3), ftpGet(4), ftpPut(5)  

NqaAdminCtrlEntry  
SEQUENCE    
  nqaAdminCtrlOwnerIndex SnmpAdminString
  nqaAdminCtrlTestName SnmpAdminString
  nqaAdminCtrlTag DisplayString
  nqaAdminCtrlType NqaType
  nqaAdminCtrlFrequency Integer32
  nqaAdminCtrlTimeOut Integer32
  nqaAdminCtrlThreshold1 Integer32
  nqaAdminCtrlThreshold2 Integer32
  nqaAdminCtrlThreshold3 Integer32
  nqaAdminCtrlStatus RowStatus

NqaAdminParaEntry  
SEQUENCE    
  nqaAdminParaTargetAddressType InetAddressType
  nqaAdminParaTargetAddress InetAddress
  nqaAdminParaTargetPort InetPortNumber
  nqaAdminParaSourceAddressType InetAddressType
  nqaAdminParaSourceAddress InetAddress
  nqaAdminParaSourcePort InetPortNumber
  nqaAdminParaMaxTtl Unsigned32
  nqaAdminParaInitialTtl Unsigned32
  nqaAdminParaStorageType StorageType
  nqaAdminParaMaxFailures Unsigned32
  nqaAdminParaDontFragment TruthValue
  nqaAdminParaDataSize Unsigned32
  nqaAdminParaDataFill OCTET STRING
  nqaAdminParaIfIndex InterfaceIndexOrZero
  nqaAdminParaByPassRouteTable TruthValue
  nqaAdminParaMiscOptions SnmpAdminString
  nqaAdminParaProbeCount Unsigned32
  nqaAdminParaTrapGeneration BITS
  nqaAdminParaTrapProbeFailureFilter Unsigned32
  nqaAdminParaTrapTestFailureFilter Unsigned32
  nqaAdminParaDSField Integer32
  nqaAdminParaDnsServerAddressType InetAddressType
  nqaAdminParaDnsServerAddress InetAddress
  nqaAdminParaOperation NqaOperation
  nqaAdminParaHttpVersion DisplayString
  nqaAdminParaHttpOperationString DisplayString
  nqaAdminParaTestFailurePercent Unsigned32
  nqaAdminParaFtpUserName DisplayString
  nqaAdminParaFtpPassword DisplayString
  nqaAdminParaFtpFilePath DisplayString
  nqaAdminParaFtpFileSize Integer32
  nqaAdminParaInterval Integer32
  nqaAdminParaNumPackets Integer32
  nqaAdminParaVrfName DisplayString
  nqaAdminParaLspAddressType INTEGER
  nqaAdminParaLspAddressMask Integer32
  nqaAdminParaLspIpAddress InetAddress
  nqaAdminParaLspPWE3VcId Unsigned32
  nqaAdminParaLspPWE3Type INTEGER
  nqaAdminParaLspPWE3Option INTEGER
  nqaAdminParaLspPWE3RemoteVcId Unsigned32
  nqaAdminParaLspPWE3RemoteAddress InetAddress
  nqaAdminParaLspExp Unsigned32
  nqaAdminParaLspReplyMode INTEGER
  nqaAdminParaResultRowMax Integer32
  nqaAdminParaHistoryRowMax Integer32
  nqaAdminParaCreateHopsEntries EnableValue
  nqaAdminParaLspVCType INTEGER
  nqaAdminParaMTraceLastHopAddress InetAddress
  nqaAdminParaMTraceSourceAddress InetAddress
  nqaAdminParaMTraceGroupAddress InetAddress
  nqaAdminParaMTraceMaxTtl Unsigned32
  nqaAdminParaMTraceSendMode INTEGER
  nqaAdminParaMTraceResponseTtl Unsigned32
  nqaAdminParaMTraceResponseAddressType InetAddressType
  nqaAdminParaMTraceResponseAddress InetAddress
  nqaAdminParaDistanceNodeType NqaDistanceNodeType
  nqaAdminParaMacAddress MacAddress
  nqaAdminParaRMepID Dot1agCfmMepIdOrZero
  nqaAdminParaMDName OCTET STRING
  nqaAdminParaMAName OCTET STRING
  nqaAdminParaMacTunnelName OCTET STRING
  nqaAdminParaPathMtuStep Integer32
  nqaAdminParaPathMtuDiscoveryPathMtuMax Integer32
  nqaAdminParaIcmpJitterMode INTEGER
  nqaAdminParaCodecType INTEGER
  nqaAdminParaIcpifAdvFactor Integer32
  nqaAdminParaFtpMode INTEGER
  nqaAdminParaHardwareBased EnabledStatus
  nqaAdminParaPppoeUserName OCTET STRING
  nqaAdminParaPppoePassword OCTET STRING
  nqaAdminParaPppoeVlanIf Integer32
  nqaAdminParaPppoeAuthenticationMode INTEGER
  nqaAdminParaPppoeRedialUpTimes Integer32
  nqaAdminParaPppoeInterval Integer32
  nqaAdminParaVsiName OCTET STRING
  nqaAdminParaVlanId VlanIdOrNone
  nqaAdminParaLspTunnelType INTEGER
  nqaAdminParaLspNextHopAddress InetAddress
  nqaAdminParaLspVersion INTEGER
  nqaAdminParaRemoteAddressType InetAddressType
  nqaAdminParaRemoteAddress InetAddress
  nqaAdminParaTimeUnit INTEGER

NqaAdminParaExtEntry  
SEQUENCE    
  nqaAdminExtPara1 OCTET STRING
  nqaAdminExtPara2 Integer32
  nqaAdminExtPara3 OCTET STRING
  nqaAdminExtPara4 Integer32
  nqaAdminExtPara5 OCTET STRING
  nqaAdminExtPara6 Integer32
  nqaAdminExtPara7 OCTET STRING
  nqaAdminExtPara8 Integer32
  nqaAdminExtPara9 OCTET STRING
  nqaAdminExtPara10 Integer32
  nqaAdminExtPara11 OCTET STRING
  nqaAdminExtPara12 Integer32
  nqaAdminExtPara13 OCTET STRING
  nqaAdminExtPara14 Integer32
  nqaAdminExtPara15 OCTET STRING
  nqaAdminExtPara16 Integer32
  nqaAdminExtPara17 OCTET STRING
  nqaAdminExtPara18 Integer32
  nqaAdminExtPara19 OCTET STRING
  nqaAdminExtPara20 Integer32
  nqaAdminExtPara21 OCTET STRING
  nqaAdminExtPara22 Integer32
  nqaAdminExtPara23 OCTET STRING
  nqaAdminExtPara24 Integer32
  nqaAdminExtPara25 OCTET STRING
  nqaAdminExtPara26 Integer32
  nqaAdminExtPara27 OCTET STRING
  nqaAdminExtPara28 Integer32
  nqaAdminExtPara29 OCTET STRING
  nqaAdminExtPara30 Integer32
  nqaAdminExtPara31 OCTET STRING
  nqaAdminExtPara32 OCTET STRING
  nqaAdminExtPara33 OCTET STRING
  nqaAdminExtPara34 OCTET STRING
  nqaAdminExtPara35 OCTET STRING
  nqaAdminExtPara36 OCTET STRING
  nqaAdminExtPara37 OCTET STRING
  nqaAdminExtPara38 OCTET STRING
  nqaAdminExtPara39 OCTET STRING
  nqaAdminExtPara40 OCTET STRING
  nqaAdminExtPara41 OCTET STRING
  nqaAdminExtPara42 OCTET STRING
  nqaAdminExtPara43 OCTET STRING
  nqaAdminExtPara44 OCTET STRING
  nqaAdminExtPara45 OCTET STRING
  nqaAdminExtPara46 OCTET STRING
  nqaAdminExtPara47 OCTET STRING
  nqaAdminExtPara48 OCTET STRING
  nqaAdminExtPara49 OCTET STRING
  nqaAdminExtPara50 OCTET STRING

NqaScheduleEntry  
SEQUENCE    
  nqaScheduleStartType INTEGER
  nqaScheduleStartTime Unsigned32
  nqaScheduleEndType INTEGER
  nqaScheduleEndTime Unsigned32
  nqaScheduleAgeTime Integer32
  nqaScheduleElapsedTime TimeInterval
  nqaScheduleNumOfInitiations Integer32
  nqaScheduleLastFinishIndex Integer32
  nqaScheduleOperStatus INTEGER
  nqaScheduleLastCollectIndex Integer32

NqaGroupEntry  
SEQUENCE    
  nqaGroupStatusType INTEGER
  nqaGroupPeriod Integer32
  nqaGroupLeaderOwnerIndex SnmpAdminString
  nqaGroupLeaderTestName SnmpAdminString
  nqaGroupMemberNum Integer32
  nqaGroupMemberFree EnableValue

NqaTcpServerEntry  
SEQUENCE    
  nqaTcpServerAddressType InetAddressType
  nqaTcpServerAddress InetAddress
  nqaTcpServerPort InetPortNumber
  nqaTcpServerVrfName DisplayString
  nqaTcpServerStatus RowStatus

NqaUdpServerEntry  
SEQUENCE    
  nqaUdpServerAddressType InetAddressType
  nqaUdpServerAddress InetAddress
  nqaUdpServerPort InetPortNumber
  nqaUdpServerVrfName DisplayString
  nqaUdpServerStatus RowStatus

NqaIcmpServerEntry  
SEQUENCE    
  nqaIcmpServerAddress InetAddress
  nqaIcmpServerVrfName DisplayString
  nqaIcmpServerAddressType InetAddressType
  nqaIcmpServerStatus RowStatus

NqaResultsEntry  
SEQUENCE    
  nqaResultsIndex Integer32
  nqaResultsHopIndex Integer32
  nqaResultsCompletions INTEGER
  nqaResultsTestAttempts Counter32
  nqaResultsCurHopCount Gauge32
  nqaResultsCurProbeCount Gauge32
  nqaResultsRTDOverThresholds Counter32
  nqaResultsSumCompletionTime Counter32
  nqaResultsSumCompletionTime2Low Counter32
  nqaResultsSumCompletionTime2High Counter32
  nqaResultsCompletionTimeMin Gauge32
  nqaResultsCompletionTimeMax Gauge32
  nqaResultsDisconnects Counter32
  nqaResultsTimeouts Counter32
  nqaResultsBusies Counter32
  nqaResultsNoConnections Counter32
  nqaResultsSequenceErrors Counter32
  nqaResultsDrops Counter32
  nqaResultsAddressType InetAddressType
  nqaResultsAddress InetAddress
  nqaResultsProbeResponses Counter32
  nqaResultsSentProbes Counter32
  nqaResultsLastGoodProbe DateAndTime
  nqaResultsLastGoodPath DateAndTime
  nqaResultsTestFinished INTEGER
  nqaResultsRttAvg Gauge32
  nqaResultsLostPacketRatio Gauge32

NqaHTTPStatsEntry  
SEQUENCE    
  nqaHTTPStatsIndex Integer32
  nqaHTTPStatsCompletions INTEGER
  nqaHTTPStatsRTDOverThresholds Counter32
  nqaHTTPStatsRTTSum Counter32
  nqaHTTPStatsRTTMin Gauge32
  nqaHTTPStatsRTTMax Gauge32
  nqaHTTPStatsDNSRTTSum Counter32
  nqaHTTPStatsDNSRTTMin Gauge32
  nqaHTTPStatsDNSRTTMax Gauge32
  nqaHTTPStatsTCPConnectRTTSum Counter32
  nqaHTTPStatsTCPConnectRTTMin Gauge32
  nqaHTTPStatsTCPConnectRTTMax Gauge32
  nqaHTTPStatsTransactionRTTSum Counter32
  nqaHTTPStatsTransactionRTTMin Gauge32
  nqaHTTPStatsTransactionRTTMax Gauge32
  nqaHTTPStatsMessageBodyOctetsSum Counter32
  nqaHTTPStatsDNSServerTimeouts Counter32
  nqaHTTPStatsTCPConnectTimeouts Counter32
  nqaHTTPStatsTransactionTimeouts Counter32
  nqaHTTPStatsDNSQueryErrors Counter32
  nqaHTTPStatsErrors Counter32
  nqaHTTPStatsTcpConnErrors Counter32
  nqaHTTPStatsProbeResponses Counter32
  nqaHTTPStatsSendProbes Counter32
  nqaHTTPStatsBusies Counter32
  nqaHTTPStatsTestFinished INTEGER
  nqaHTTPStatsRttAvg Gauge32
  nqaHTTPStatsLostPacketRatio Gauge32

NqaJitterStatsEntry  
SEQUENCE    
  nqaJitterStatsIndex Integer32
  nqaJitterStatsCompletions INTEGER
  nqaJitterStatsRTDOverThresholds Counter32
  nqaJitterStatsNumOfRTT Counter32
  nqaJitterStatsRTTSum Counter32
  nqaJitterStatsRTTSum2Low Counter32
  nqaJitterStatsRTTSum2High Counter32
  nqaJitterStatsRTTMin Gauge32
  nqaJitterStatsRTTMax Gauge32
  nqaJitterStatsMinOfPositivesSD Gauge32
  nqaJitterStatsMaxOfPositivesSD Gauge32
  nqaJitterStatsNumOfPositivesSD Counter32
  nqaJitterStatsSumOfPositivesSD Counter32
  nqaJitterStatsSum2OfPositivesSDLow Counter32
  nqaJitterStatsSum2OfPositivesSDHigh Counter32
  nqaJitterStatsMinOfNegativesSD Gauge32
  nqaJitterStatsMaxOfNegativesSD Gauge32
  nqaJitterStatsNumOfNegativesSD Counter32
  nqaJitterStatsSumOfNegativesSD Counter32
  nqaJitterStatsSum2OfNegativesSDLow Counter32
  nqaJitterStatsSum2OfNegativesSDHigh Counter32
  nqaJitterStatsMinOfPositivesDS Gauge32
  nqaJitterStatsMaxOfPositivesDS Gauge32
  nqaJitterStatsNumOfPositivesDS Counter32
  nqaJitterStatsSumOfPositivesDS Counter32
  nqaJitterStatsSum2OfPositivesDSLow Counter32
  nqaJitterStatsSum2OfPositivesDSHigh Counter32
  nqaJitterStatsMinOfNegativesDS Gauge32
  nqaJitterStatsMaxOfNegativesDS Gauge32
  nqaJitterStatsNumOfNegativesDS Counter32
  nqaJitterStatsSumOfNegativesDS Counter32
  nqaJitterStatsSum2OfNegativesDSLow Counter32
  nqaJitterStatsSum2OfNegativesDSHigh Counter32
  nqaJitterStatsPacketLossSD Counter32
  nqaJitterStatsPacketLossDS Counter32
  nqaJitterStatsPacketOutOfSequences Counter32
  nqaJitterStatsErrors Counter32
  nqaJitterStatsBusies Counter32
  nqaJitterStatsTimeouts Counter32
  nqaJitterStatsProbeResponses Counter32
  nqaJitterStatsSentProbes Counter32
  nqaJitterStatsDrops Counter32
  nqaJitterStatsTestFinished INTEGER
  nqaJitterStatsMaxDelaySD Gauge32
  nqaJitterStatsMaxDelayDS Gauge32
  nqaJitterStatsRTTAvg Gauge32
  nqaJitterStatsPacketLossRatio Gauge32
  nqaJitterStatsAvgJitter Gauge32
  nqaJitterStatsAvgJitterSD Gauge32
  nqaJitterStatsAvgJitterDS Gauge32
  nqaJitterStatsJitterOut OCTET STRING
  nqaJitterStatsJitterIn OCTET STRING
  nqaJitterStatsOWDOverThresholdsSD Counter32
  nqaJitterStatsPktLossUnknown Counter32
  nqaJitterStatsNumOfOWD Counter32
  nqaJitterStatsOWSumSD Counter32
  nqaJitterStatsOWSumDS Counter32
  nqaJitterStatsOWDOverThresholdsDS Counter32
  nqaJitterStatsOperOfIcpif Gauge32
  nqaJitterStatsOperOfMos Gauge32
  nqaJitterStatsMinDelaySD Gauge32
  nqaJitterStatsSum2DelaySDLow Gauge32
  nqaJitterStatsSum2DelaySDHigh Counter32
  nqaJitterStatsMinDelayDS Gauge32
  nqaJitterStatsSum2DelayDSLow Gauge32
  nqaJitterStatsSum2DelayDSHigh Counter32
  nqaJitterStatsTimeUnit INTEGER
  nqaJitterStatsAvgDelaySD Gauge32
  nqaJitterStatsAvgDelayDS Gauge32
  nqaJitterStatsPktRewriteNum Counter32
  nqaJitterStatsPktRewriteRatio Gauge32
  nqaJitterStatsPktDisorderNum Counter32
  nqaJitterStatsPktDisorderRatio Gauge32
  nqaJitterStatsFragPktDisorderNum Counter32
  nqaJitterStatsFragPktDisorderRatio Gauge32

NqaFTPStatsEntry  
SEQUENCE    
  nqaFTPStatsIndex Integer32
  nqaFTPStatsCompletions INTEGER
  nqaFTPStatsRTDOverThresholds Counter32
  nqaFTPStatsCtrlConnMaxTime Gauge32
  nqaFTPStatsCtrlConnMinTime Gauge32
  nqaFTPStatsCtrlConnAveTime Gauge32
  nqaFTPStatsDataConnMaxTime Gauge32
  nqaFTPStatsDataConnMinTime Gauge32
  nqaFTPStatsDataConnAveTime Gauge32
  nqaFTPStatsConnectSumTimeMax Gauge32
  nqaFTPStatsConnectSumTimeMin Gauge32
  nqaFTPStatsConnectSumTimeAve Gauge32
  nqaFTPStatsMessageBodyOctetsSum Counter32
  nqaFTPStatsErrors Counter32
  nqaFTPStatsTimeouts Counter32
  nqaFTPStatsDiscontinued Counter32
  nqaFTPStatsProbeResponses Counter32
  nqaFTPStatsSendProbes Counter32
  nqaFTPStatsTestFinished INTEGER
  nqaFTPStatsRttAvg Gauge32
  nqaFTPStatsLostPacketRatio Gauge32

NqaMpingStatsEntry  
SEQUENCE    
  nqaMpingStatsIndex Integer32
  nqaMpingStatsReceiverIndex Integer32
  nqaMpingStatsTargetAddressType InetAddressType
  nqaMpingStatsTargetAddress InetAddress
  nqaMpingStatsReceiverAddress InetAddress
  nqaMpingStatsCompletions INTEGER
  nqaMpingStatsRTDOverThresholds Counter32
  nqaMpingStatsSumCompletionTime Counter32
  nqaMpingStatsSumCompletionTime2Low Counter32
  nqaMpingStatsSumCompletionTime2High Counter32
  nqaMpingStatsCompletionTimeMin Gauge32
  nqaMpingStatsCompletionTimeMax Gauge32
  nqaMpingStatsTimeouts Counter32
  nqaMpingStatsBusies Counter32
  nqaMpingStatsSequenceErrors Counter32
  nqaMpingStatsDrops Counter32
  nqaMpingStatsProbeResponses Counter32
  nqaMpingStatsSentProbes Counter32
  nqaMpingStatsLastGoodProbe DateAndTime
  nqaMpingStatsTestFinished INTEGER
  nqaMpingStatsReceiverCount Gauge32
  nqaMpingStatsLastFibHit TruthValue
  nqaMpingStatsRttAvg Gauge32
  nqaMpingStatsLostPacketRatio Gauge32

NqaMtracertStatsEntry  
SEQUENCE    
  nqaMtracertStatsIndex Integer32
  nqaMtracertStatsHopIndex Integer32
  nqaMtracertStatsAddressType InetAddressType
  nqaMtracertStatsAddress InetAddress
  nqaMtracertStatsCompletions INTEGER
  nqaMtracertStatsCurHopCount Gauge32
  nqaMtracertStatsCurProbeCount Gauge32
  nqaMtracertStatsRTDOverThresholds Counter32
  nqaMtracertStatsTimeouts Counter32
  nqaMtracertStatsBusies Counter32
  nqaMtracertStatsSequenceErrors Counter32
  nqaMtracertStatsDrops Counter32
  nqaMtracertStatsProbeResponses Counter32
  nqaMtracertStatsSentProbes Counter32
  nqaMtracertStatsLastGoodProbe DateAndTime
  nqaMtracertStatsLastGoodPath DateAndTime
  nqaMtracertStatsTestFinished INTEGER
  nqaMtracertStatsCurPathTTL Gauge32
  nqaMtracertStatsMaxPathTTL Gauge32
  nqaMtracertStatsInPkgLossRate Gauge32
  nqaMtracertStatsSGPkgLossRate Gauge32
  nqaMtracertStatsInPkgRate Gauge32
  nqaMtracertStatsOutPkgRate Gauge32
  nqaMtracertStatsTimeDelay Gauge32

NqaPathMtuStatsEntry  
SEQUENCE    
  nqaPathMtuStatsIndex Integer32
  nqaPathMtuStatsAddressType InetAddressType
  nqaPathMtuStatsAddress InetAddress
  nqaPathMtuStatsCompletions INTEGER
  nqaPathMtuStatsSentProbes Counter32
  nqaPathMtuStatsProbeResponses Counter32
  nqaPathMtuStatsDiscoveryPathMtuMin Gauge32
  nqaPathMtuStatsDiscoveryPathMtuMax Gauge32
  nqaPathMtuStatsOptimumFirstStep Gauge32
  nqaPathMtuStatsBusies Counter32
  nqaPathMtuStatsTimeouts Counter32
  nqaPathMtuStatsDrops Counter32
  nqaPathMtuStatsPathMtu Gauge32
  nqaPathMtuStatsTestFinished INTEGER

NqaPathJitterStatsEntry  
SEQUENCE    
  nqaPathJitterStatsIndex Integer32
  nqaPathJitterStatsHopIndex Integer32
  nqaPathJitterStatsCompletions INTEGER
  nqaPathJitterStatsAddressType InetAddressType
  nqaPathJitterStatsAddress InetAddress
  nqaPathJitterStatsRtdOverThresholds Counter32
  nqaPathJitterStatsNumOfRtt Counter32
  nqaPathJitterStatsRttSum Counter32
  nqaPathJitterStatsRttSum2Low Counter32
  nqaPathJitterStatsRttSum2High Counter32
  nqaPathJitterStatsRttMin Gauge32
  nqaPathJitterStatsRttMax Gauge32
  nqaPathJitterStatsMinOfPositivesSD Gauge32
  nqaPathJitterStatsMaxOfPositivesSD Gauge32
  nqaPathJitterStatsNumOfPositivesSD Counter32
  nqaPathJitterStatsSumOfPositivesSD Counter32
  nqaPathJitterStatsSum2OfPositivesSDLow Counter32
  nqaPathJitterStatsSum2OfPositivesSDHigh Counter32
  nqaPathJitterStatsMinOfNegativesSD Gauge32
  nqaPathJitterStatsMaxOfNegativesSD Gauge32
  nqaPathJitterStatsNumOfNegativesSD Counter32
  nqaPathJitterStatsSumOfNegativesSD Counter32
  nqaPathJitterStatsSum2OfNegativesSDLow Counter32
  nqaPathJitterStatsSum2OfNegativesSDHigh Counter32
  nqaPathJitterStatsMinOfPositivesDS Gauge32
  nqaPathJitterStatsMaxOfPositivesDS Gauge32
  nqaPathJitterStatsNumOfPositivesDS Counter32
  nqaPathJitterStatsSumOfPositivesDS Counter32
  nqaPathJitterStatsSum2OfPositivesDSLow Counter32
  nqaPathJitterStatsSum2OfPositivesDSHigh Counter32
  nqaPathJitterStatsMinOfNegativesDS Gauge32
  nqaPathJitterStatsMaxOfNegativesDS Gauge32
  nqaPathJitterStatsNumOfNegativesDS Counter32
  nqaPathJitterStatsSumOfNegativesDS Counter32
  nqaPathJitterStatsSum2OfNegativesDSLow Counter32
  nqaPathJitterStatsSum2OfNegativesDSHigh Counter32
  nqaPathJitterStatsPacketLossSD Counter32
  nqaPathJitterStatsPacketLossDS Counter32
  nqaPathJitterStatsPacketOutOfSequences Counter32
  nqaPathJitterStatsErrors Counter32
  nqaPathJitterStatsBusies Counter32
  nqaPathJitterStatsTimeouts Counter32
  nqaPathJitterStatsProbeResponses Counter32
  nqaPathJitterStatsSentProbes Counter32
  nqaPathJitterStatsDrops Counter32
  nqaPathJitterStatsTestFinished INTEGER
  nqaPathJitterStatsMaxDelaySD Gauge32
  nqaPathJitterStatsMaxDelayDS Gauge32
  nqaPathJitterStatsRttAvg Gauge32
  nqaPathJitterStatsPacketLossRatio Gauge32
  nqaPathJitterStatsAvgJitter Gauge32
  nqaPathJitterStatsAvgJitterSD Gauge32
  nqaPathJitterStatsAvgJitterDS Gauge32
  nqaPathJitterStatsJitterOut OCTET STRING
  nqaPathJitterStatsJitterIn OCTET STRING
  nqaPathJitterStatsOwdOverThresholdsSD Counter32
  nqaPathJitterStatsPktLossUnknown Counter32
  nqaPathJitterStatsNumOfOwd Counter32
  nqaPathJitterStatsOwdSumSD Counter32
  nqaPathJitterStatsOwdSumDS Counter32
  nqaPathJitterStatsOwdOverThresholdsDS Counter32

NqaPppoeStatsEntry  
SEQUENCE    
  nqaPppoeStatsIndex Integer32
  nqaPppoeRedialIndex Integer32
  nqaPppoeStatsCompletions INTEGER
  nqaPppoeStatsCurrentPhase INTEGER
  nqaPppoeStatsErrorMessage INTEGER
  nqaPppoeDiscoveryTimeout Gauge32
  nqaPppoeLcpTimeout Gauge32
  nqaPppoeAuthorizationTimeout Gauge32
  nqaPppoeNcpTimeout Gauge32
  nqaPppoeConnectionTime Gauge32
  nqaPppoeClientSessionId Gauge32
  nqaPppoeClientIpAddress InetAddress
  nqaPppoeGatewayIpAddress InetAddress

NqaHistoryEntry  
SEQUENCE    
  nqaHistoryIndex Integer32
  nqaHistoryHopIndex Integer32
  nqaHistoryProbeIndex Integer32
  nqaHistoryTimeStamp DateAndTime
  nqaHistoryAddressType InetAddressType
  nqaHistoryAddress InetAddress
  nqaHistoryCompletionTime Integer32
  nqaHistoryFinishState INTEGER
  nqaHistoryLastRC Integer32

NqaMpingHistoryEntry  
SEQUENCE    
  nqaMpingHistoryIndex Integer32
  nqaMpingHistoryReceiverIndex Integer32
  nqaMpingHistoryResponseIndex Integer32
  nqaMpingHistoryAddressType InetAddressType
  nqaMpingHistoryAddress InetAddress
  nqaMpingHistoryReceiverAddress InetAddress
  nqaMpingHistoryTimeStamp DateAndTime
  nqaMpingHistoryCompletionTime Integer32
  nqaMpingHistoryFinishState INTEGER
  nqaMpingHistoryLastRC Integer32
  nqaMpingHistoryFibHit TruthValue

NqaMtracertHistoryEntry  
SEQUENCE    
  nqaMtracertHistoryIndex Integer32
  nqaMtracertHistoryHopIndex Integer32
  nqaMtracertHistoryAddressType InetAddressType
  nqaMtracertHistoryAddress InetAddress
  nqaMtracertHistoryTimeStamp DateAndTime
  nqaMtracertHistoryCompletionTime Integer32
  nqaMtracertHistoryLastRC Integer32
  nqaMtracertHistoryCurQueryMode INTEGER
  nqaMtracertHistoryQueryArrivalTime Unsigned32
  nqaMtracertHistoryIncomingIfAddress InetAddress
  nqaMtracertHistoryOutgoingIfAddress InetAddress
  nqaMtracertHistoryPreHopRouterAddress InetAddress
  nqaMtracertHistoryInputPacketCount Gauge32
  nqaMtracertHistoryOutputPacketCount Gauge32
  nqaMtracertHistoryTotalSGPacketCount Gauge32
  nqaMtracertHistoryRtgProtocol INTEGER
  nqaMtracertHistoryFwdTTL Gauge32
  nqaMtracertHistoryFwdCode INTEGER
  nqaMtracertHistroyFinishState INTEGER

NqaVplsMacTracertHistoryEntry  
SEQUENCE    
  nqaVplsMacTracertHistoryIndex Integer32
  nqaVplsMacTracertHistoryHopIndex Integer32
  nqaVplsMacTracertHistoryResponseIndex Integer32
  nqaVplsMacTracertHistoryTimeStamp DateAndTime
  nqaVplsMacTracertHistoryAddressType InetAddressType
  nqaVplsMacTracertHistoryAddress InetAddress
  nqaVplsMacTracertHistoryCompletionTime Integer32
  nqaVplsMacTracertHistoryFinishState INTEGER
  nqaVplsMacTracertHistoryHitFlag TruthValue
  nqaVplsMacTracertHistoryDSCount Integer32
  nqaVplsMacTracertHistorySuccessPathNode TruthValue

NqaVplsMacTracertHistoryDSEntry  
SEQUENCE    
  nqaVplsMacTracertHistoryDSIndex Integer32
  nqaVplsMacTracertHistoryDSAddress InetAddress

NqaVplsMTraceHistoryEntry  
SEQUENCE    
  nqaVplsMTraceHistoryIndex Integer32
  nqaVplsMTraceHistoryHopIndex Integer32
  nqaVplsMTraceHistoryResponseIndex Integer32
  nqaVplsMTraceHistoryResponserAddressType InetAddressType
  nqaVplsMTraceHistoryResponserAddress InetAddress
  nqaVplsMTraceHistoryUpStreamAddressType InetAddressType
  nqaVplsMTraceHistoryUpStreamAddress InetAddress
  nqaVplsMTraceHistoryReceivedTtl Unsigned32
  nqaVplsMTraceHistoryIGMPVersion INTEGER
  nqaVplsMTraceHistoryIGMPSnpgEnable EnableValue
  nqaVplsMTraceHistoryIGMPProxyEnable EnableValue
  nqaVplsMTraceHistoryIGMPRouterPortLearningEnable EnableValue
  nqaVplsMTraceHistoryRequireRouterAlertEnable EnableValue
  nqaVplsMTraceHistoryForwardMode INTEGER
  nqaVplsMTraceHistoryHitFlag TruthValue
  nqaVplsMTraceHistoryPWExist TruthValue
  nqaVplsMTraceHistoryGroupPolicy INTEGER
  nqaVplsMTraceHistoryCACExist INTEGER
  nqaVplsMTraceHistoryRcvQueryCount Gauge32
  nqaVplsMTraceHistoryRcvReportCount Gauge32
  nqaVplsMTraceHistoryRcvLeaveCount Gauge32
  nqaVplsMTraceHistoryTimeStamp DateAndTime
  nqaVplsMTraceHistoryCompletionTime Integer32
  nqaVplsMTraceHistoryLastRC Integer32
  nqaVplsMTraceHistoryLastRSC Integer32
  nqaVplsMTraceHistoryFinishState INTEGER
  nqaVplsMTraceHistorySuccessPathNode INTEGER

NqaMacTraceHistoryEntry  
SEQUENCE    
  nqaMacTraceHistoryIndex Integer32
  nqaMacTraceHistoryReceiveOrder Integer32
  nqaMacTraceHistoryTTL Integer32
  nqaMacTraceHistorySeqNumber Unsigned32
  nqaMacTraceHistoryCompletionTime Integer32
  nqaMacTraceHistoryForwarded TruthValue
  nqaMacTraceHistoryTerminalMep TruthValue
  nqaMacTraceHistoryRelayAction HWDot1agCfmRelayActionFieldValue
  nqaMacTraceHistoryIngressAction HWDot1agCfmIngressActionFieldValue
  nqaMacTraceHistoryIngressMac MacAddress
  nqaMacTraceHistoryIngressIfName OCTET STRING
  nqaMacTraceHistoryEgressAction HWDot1agCfmEgressActionFieldValue
  nqaMacTraceHistoryEgressMac MacAddress
  nqaMacTraceHistoryEgressIfName OCTET STRING

NqaJitterCollectStatsEntry  
SEQUENCE    
  nqaJitterCollectStatsIndex Integer32
  nqaJitterCollectStatsCompletions Counter32
  nqaJitterCollectStatsRTDOverThresholds Counter32
  nqaJitterCollectStatsOWDOverThresholdsSD Counter32
  nqaJitterCollectStatsOWDOverThresholdsDS Counter32
  nqaJitterCollectStatsNumOfRTT Counter32
  nqaJitterCollectStatsRTTSum Counter32
  nqaJitterCollectStatsRTTSum2Low Counter32
  nqaJitterCollectStatsRTTSum2High Counter32
  nqaJitterCollectStatsRTTMin Gauge32
  nqaJitterCollectStatsRTTMax Gauge32
  nqaJitterCollectStatsMinOfPositivesSD Gauge32
  nqaJitterCollectStatsMaxOfPositivesSD Gauge32
  nqaJitterCollectStatsNumOfPositivesSD Counter32
  nqaJitterCollectStatsSumOfPositivesSD Counter32
  nqaJitterCollectStatsSum2OfPositivesSDLow Counter32
  nqaJitterCollectStatsSum2OfPositivesSDHigh Counter32
  nqaJitterCollectStatsMinOfNegativesSD Gauge32
  nqaJitterCollectStatsMaxOfNegativesSD Gauge32
  nqaJitterCollectStatsNumOfNegativesSD Counter32
  nqaJitterCollectStatsSumOfNegativesSD Counter32
  nqaJitterCollectStatsSum2OfNegativesSDLow Counter32
  nqaJitterCollectStatsSum2OfNegativesSDHigh Counter32
  nqaJitterCollectStatsMinOfPositivesDS Gauge32
  nqaJitterCollectStatsMaxOfPositivesDS Gauge32
  nqaJitterCollectStatsNumOfPositivesDS Counter32
  nqaJitterCollectStatsSumOfPositivesDS Counter32
  nqaJitterCollectStatsSum2OfPositivesDSLow Counter32
  nqaJitterCollectStatsSum2OfPositivesDSHigh Counter32
  nqaJitterCollectStatsMinOfNegativesDS Gauge32
  nqaJitterCollectStatsMaxOfNegativesDS Gauge32
  nqaJitterCollectStatsNumOfNegativesDS Counter32
  nqaJitterCollectStatsSumOfNegativesDS Counter32
  nqaJitterCollectStatsSum2OfNegativesDSLow Counter32
  nqaJitterCollectStatsSum2OfNegativesDSHigh Counter32
  nqaJitterCollectStatsMaxDelaySD Gauge32
  nqaJitterCollectStatsMaxDelayDS Gauge32
  nqaJitterCollectStatsNumOfOWD Counter32
  nqaJitterCollectStatsOWSumSD Counter32
  nqaJitterCollectStatsOWSumDS Counter32
  nqaJitterCollectStatsPacketLossSD Counter32
  nqaJitterCollectStatsPacketLossDS Counter32
  nqaJitterCollectStatsPacketLossUnknown Counter32
  nqaJitterCollectStatsPacketOutOfSequences Counter32
  nqaJitterCollectStatsPacketLossRatio Gauge32
  nqaJitterCollectStatsErrors Counter32
  nqaJitterCollectStatsBusies Counter32
  nqaJitterCollectStatsTimeouts Counter32
  nqaJitterCollectStatsProbeResponses Counter32
  nqaJitterCollectStatsSentProbes Counter32
  nqaJitterCollectStatsDrops Counter32
  nqaJitterCollectStatsRTTAvg Gauge32
  nqaJitterCollectStatsAvgJitter Gauge32
  nqaJitterCollectStatsAvgJitterSD Gauge32
  nqaJitterCollectStatsAvgJitterDS Gauge32
  nqaJitterCollectStatsJitterOut OCTET STRING
  nqaJitterCollectStatsJitterIn OCTET STRING
  nqaJitterCollectStatsMinDelaySD Gauge32
  nqaJitterCollectStatsMinDelayDS Gauge32
  nqaJitterCollectStatsAvgDelaySD Gauge32
  nqaJitterCollectStatsAvgDelayDS Gauge32
  nqaJitterCollectStatsPktRewriteNum Counter32
  nqaJitterCollectStatsPktRewriteRatio Gauge32
  nqaJitterCollectStatsPktDisorderNum Counter32
  nqaJitterCollectStatsPktDisorderRatio Gauge32
  nqaJitterCollectStatsFragPktDisorderNum Counter32
  nqaJitterCollectStatsFragPktDisorderRatio Gauge32

NqaAlarmEntry  
SEQUENCE    
  nqaAlarmIndex Integer32
  nqaAlarmVariable INTEGER
  nqaAlarmSampleType INTEGER
  nqaAlarmValue Integer32
  nqaAlarmStartUpNqaAlarm INTEGER
  nqaAlarmRisingThreshold Integer32
  nqaAlarmFallingThreshold Integer32
  nqaAlarmRisingEventIndex Integer32
  nqaAlarmFallingEventIndex Integer32
  nqaAlarmDescription OCTET STRING
  nqaAlarmStatus RowStatus

NqaEventEntry  
SEQUENCE    
  nqaEventIndex Integer32
  nqaEventType INTEGER
  nqaEventDescription OCTET STRING
  nqaEventAdminName OCTET STRING
  nqaEventOperationTag OCTET STRING
  nqaEventStatus RowStatus

Defined Values

nqa 1.3.6.1.4.1.2011.5.25.111
HUAWEI service quality detect funcion.
MODULE-IDENTITY    

nqaBase 1.3.6.1.4.1.2011.5.25.111.1
OBJECT IDENTIFIER    

nqaVersion 1.3.6.1.4.1.2011.5.25.111.1.1
The NQA version (for example, 1.1). It can be used for version management.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

nqaEnable 1.3.6.1.4.1.2011.5.25.111.1.2
Indicates the switch of enabling NQA client. (The value range: enable:1; disable:2.The default value is enable(1))
Status: current Access: read-write
OBJECT-TYPE    
  EnableValue  

nqaReset 1.3.6.1.4.1.2011.5.25.111.1.3
Clears all the enabled test configurations. (The value range: enable:1; disable:2. The default value is disable(2))
Status: current Access: read-write
OBJECT-TYPE    
  EnableValue  

nqaTimeOfLastSetError 1.3.6.1.4.1.2011.5.25.111.1.4
The time of the last configuration error. (0 indicates that the configuration does not fail).
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

nqaLastSetError 1.3.6.1.4.1.2011.5.25.111.1.5
The time of the last configuration error. (0 indicates that the configuration does not fail).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

nqaNumOfCurrentCtrlEntry 1.3.6.1.4.1.2011.5.25.111.1.6
The total number of current configuration tests.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaMaxConcurrentRequests 1.3.6.1.4.1.2011.5.25.111.1.7
The maximum number of concurrent active requests that are allowed within an agent implementation.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

nqaMaxNumOfRequests 1.3.6.1.4.1.2011.5.25.111.1.8
The maximum number of requests that are allowed within an agent implementation.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

nqaJitterVersion 1.3.6.1.4.1.2011.5.25.111.1.9
Selects the version of jitter test. (The value range: old version:1, new version:2. The default value is old version(1))
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaSupportTestType 1.3.6.1.4.1.2011.5.25.111.1.10
Test type that the current device supports. Data structure of the type is in the format of bits. Each bit represents a test type. The mappings between bits and tests are as follows: icmp(0), tcp(1), udp(2), http(3), ftp(4), jitter(5), snmp(6), trace(7), lspPing(8), lspTrace(9), dns(10), dhcp(11), dlsw(12), pwe3Ping(13), pwe3Trace(14), mPing(15), mTrace(16), macPing(17), macTunnelPing(18), lspJitter(19), icmpJitter(20), pathJitter(21), pathMtu(22), pppoe(23), vplsmPing(24), vplsmacPing(25), vplsmacTrace(26), vplsMTrace(27), gmacping(28), gmactrace(29), mactrace(30), vplspwping(31), vplspwtrace(32) The value #0x00 indicates don't suppourt all testtypes.
Status: current Access: read-only
OBJECT-TYPE    
  BITS icmp(0), tcp(1), udp(2), http(3), ftp(4), jitter(5), snmp(6), trace(7), lspPing(8), lspTrace(9), dns(10), dhcp(11), dlsw(12), pwe3Ping(13), pwe3Trace(14), mPing(15), mTrace(16), macPing(17), macTunnelPing(18), lspJitter(19), icmpJitter(20), pathJitter(21), pathMtu(22), pppoe(23), vplsmPing(24), vplsmacPing(25), vplsmacTrace(26), vplsMTrace(27), gmacping(28), gmactrace(29), mactrace(30), vplspwping(31), vplspwtrace(32)  

nqaSupportServerType 1.3.6.1.4.1.2011.5.25.111.1.11
Test type that the current device supports. Data structure of the type is in the format of bits. Each bit represents a test type. tcpServer(0), udpServer(1), icmpServer(2) The value #0x00 indicates don't suppourt all servertypes.
Status: current Access: read-only
OBJECT-TYPE    
  BITS tcpServer(0), udpServer(1), icmpServer(2)  

nqaCtrl 1.3.6.1.4.1.2011.5.25.111.2
OBJECT IDENTIFIER    

nqaAdminCtrlTable 1.3.6.1.4.1.2011.5.25.111.2.1
A table of NQA monitoring definitions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaAdminCtrlEntry

nqaAdminCtrlEntry 1.3.6.1.4.1.2011.5.25.111.2.1.1
Defines an entry in the nqaAdminCtrlTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaAdminCtrlEntry  

nqaAdminCtrlOwnerIndex 1.3.6.1.4.1.2011.5.25.111.2.1.1.1
To facilitate the provisioning of access control by a security administrator using the View-Based Access Control Model for tables in which multiple users may need to independently create or modify entries, the initial index is used as an 'ownerindex'. When used in conjunction with such a security policy all entries in the table belonging to a particular user (or group) will have the same value for this initial index. For a given user's entries in a particular table, the object identifiers for the information in these entries will have the same subidentifiers (except for the 'column' subidentifier) up to the end of the encoded owner index.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

nqaAdminCtrlTestName 1.3.6.1.4.1.2011.5.25.111.2.1.1.2
The name of a test. This is locally unique, within the scope of an nqaAdminCtrlOwnerIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

nqaAdminCtrlTag 1.3.6.1.4.1.2011.5.25.111.2.1.1.3
A string which is the description of the test instance.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

nqaAdminCtrlType 1.3.6.1.4.1.2011.5.25.111.2.1.1.4
The type of the test instance.
Status: current Access: read-create
OBJECT-TYPE    
  NqaType  

nqaAdminCtrlFrequency 1.3.6.1.4.1.2011.5.25.111.2.1.1.5
Specifies the interval when the test instance repeats.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

nqaAdminCtrlTimeOut 1.3.6.1.4.1.2011.5.25.111.2.1.1.6
Specifies the duration to wait for the completion of test instance. The default value of DHCP-type and FTP-type test instance is 15s, The default value of PPPoE-type test instance is 30s, and that of other types is 3s.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..60  

nqaAdminCtrlThreshold1 1.3.6.1.4.1.2011.5.25.111.2.1.1.7
Represents the threshold of RTD (Round Trip Delay). If the RTT violates the threshold, the corresponding counter will increase. It applies to any type of test instance.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

nqaAdminCtrlThreshold2 1.3.6.1.4.1.2011.5.25.111.2.1.1.8
Represents the threshold of OWD (One Way Delay) from source to destination. If the OWD violates the threshold, the corresponding counter will increase. It applies only to jitter-type test instances.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

nqaAdminCtrlThreshold3 1.3.6.1.4.1.2011.5.25.111.2.1.1.9
Represents the threshold of OWD (One Way Delay) from destination to source. If the OWD violates the threshold, the corresponding counter will increase. It applies only to jitter-type test instances.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

nqaAdminCtrlStatus 1.3.6.1.4.1.2011.5.25.111.2.1.1.10
To set the value of this object can create or delete the specified test instance and the records belonging to it. Before deleting a test instance, the custom must make sure that the status of the test instance is inactive through nqaScheduleOperStatus. The value can be set to 'CreateAndGo (4)', 'Destroy (6)' and 'Active (1)'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

nqaAdminParaTable 1.3.6.1.4.1.2011.5.25.111.2.2
Set parameter for a test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaAdminParaEntry

nqaAdminParaEntry 1.3.6.1.4.1.2011.5.25.111.2.2.1
set parameter in the nqaAdminParaTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaAdminParaEntry  

nqaAdminParaTargetAddressType 1.3.6.1.4.1.2011.5.25.111.2.2.1.1
Represents the address type of destination.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

nqaAdminParaTargetAddress 1.3.6.1.4.1.2011.5.25.111.2.2.1.2
Represents the address of destination.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nqaAdminParaTargetPort 1.3.6.1.4.1.2011.5.25.111.2.2.1.3
Represents the port number of destination.
Status: current Access: read-write
OBJECT-TYPE    
  InetPortNumber  

nqaAdminParaSourceAddressType 1.3.6.1.4.1.2011.5.25.111.2.2.1.4
Represents the address type of source.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

nqaAdminParaSourceAddress 1.3.6.1.4.1.2011.5.25.111.2.2.1.5
Represents the address of source.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nqaAdminParaSourcePort 1.3.6.1.4.1.2011.5.25.111.2.2.1.6
Represents the port number of source.
Status: current Access: read-write
OBJECT-TYPE    
  InetPortNumber  

nqaAdminParaMaxTtl 1.3.6.1.4.1.2011.5.25.111.2.2.1.7
Specifies the maximum value of TTL. The value cannot be set to 0 unless the test-type is pwe3ping, the lsp-version is rfc4379, and the ttl-copymode is pipe.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

nqaAdminParaInitialTtl 1.3.6.1.4.1.2011.5.25.111.2.2.1.8
Specifies the initial value of TTL.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

nqaAdminParaStorageType 1.3.6.1.4.1.2011.5.25.111.2.2.1.9
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
Status: current Access: read-write
OBJECT-TYPE    
  StorageType  

nqaAdminParaMaxFailures 1.3.6.1.4.1.2011.5.25.111.2.2.1.10
The value of this object indicates the maximum number of consecutive timeouts allowed before terminating a remote traceroute request. A value of 255 (maximum hop count/possible TTL value) indicates that the function of terminating a remote traceroute request when a specific number of successive timeouts are detected is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

nqaAdminParaDontFragment 1.3.6.1.4.1.2011.5.25.111.2.2.1.11
This object enables setting of Don't Fragment (DF) flag in the IP header for a probe. Use of this object enables performing a manual PATH MTU test.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

nqaAdminParaDataSize 1.3.6.1.4.1.2011.5.25.111.2.2.1.12
The size of data field in packet.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

nqaAdminParaDataFill 1.3.6.1.4.1.2011.5.25.111.2.2.1.13
Represents the characters used for filling the data field. This object is used together with the corresponding object, nqaAdminParaDataSize.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nqaAdminParaIfIndex 1.3.6.1.4.1.2011.5.25.111.2.2.1.14
Specified the source interface or tunnel, from which probes of the test instance are sent. The object applies to DHCP, jitter, icmpjitter, ICMP, lspping or lsptrace type test instance. The value zero implies that the object is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  InterfaceIndexOrZero  

nqaAdminParaByPassRouteTable 1.3.6.1.4.1.2011.5.25.111.2.2.1.15
The purpose of this object is to optionally enable bypassing the route table. If enabled, the remote host will bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-attached network, an error is returned. This option can be used to perform the ping/traceroute operation to a local host through an interface that has no route defined (e.g., after the interface was dropped by routed).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

nqaAdminParaMiscOptions 1.3.6.1.4.1.2011.5.25.111.2.2.1.16
Enables an application to specify implementation dependent options.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

nqaAdminParaProbeCount 1.3.6.1.4.1.2011.5.25.111.2.2.1.17
Specifies the number of packets sent by the test instance, or times of probe repeated, in which may send several packets. The second case applies to jitter-type test instances.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..15  

nqaAdminParaTrapGeneration 1.3.6.1.4.1.2011.5.25.111.2.2.1.18
Switch of notification. Determine whether and how to send notifications for the test instance: - probeFailure(0) - Generate a PathChange notification when the current path varies from a previously determined path. - testFailure(1) - Generate a TestFailed notification when the full path to a target can't be determined. - testCompletion(2) - Generate a TestCompleted notification when the path to a target has been determined. - overRtdThreshold(3) - Generate a Overthreshold of RTD notification when the statistic results exceed threshold. - overOwdThresholdSd(4) - Generate a Overthreshold of OWD-SD notification when the statistic results exceed threshold. - overOwdThresholdDs(5) - Generate a Overthreshold of OWD-DS notification when the statistic results exceed threshold. The value #0x00 indicates disable all notifications.
Status: current Access: read-write
OBJECT-TYPE    
  BITS probeFailure(0), testFailure(1), testCompletion(2), overRtdThreshold(3), overOwdThresholdSd(4), overOwdThresholdDs(5)  

nqaAdminParaTrapProbeFailureFilter 1.3.6.1.4.1.2011.5.25.111.2.2.1.19
Specifies the condition when to trigger an nqaProbeFailed notification. When the number of consecutive failed probes violates the threshold indicated by nqaAdminParaTrapProbeFailureFilter, a notification will be created. This object is used together with nqaAdminParaTrapGeneration.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..15  

nqaAdminParaTrapTestFailureFilter 1.3.6.1.4.1.2011.5.25.111.2.2.1.20
Specifies the condition when to trigger an nqaTestFailed notification. When the number of failed tests violates the threshold indicated by nqaAdminParaTrapTestFailureFilter, a notification will be created. There are usually several probes in each test. This object is used together with nqaAdminParaTrapGeneration.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..15  

nqaAdminParaDSField 1.3.6.1.4.1.2011.5.25.111.2.2.1.21
Specifies the Differentiated Services (DS) field in the IP packet. The DS field is defined as the Type Of Service (TOS) octet in IPv4 header or as the Traffic Class octet in IPv6 header.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

nqaAdminParaDnsServerAddressType 1.3.6.1.4.1.2011.5.25.111.2.2.1.22
Specifies the address type of DNS server.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

nqaAdminParaDnsServerAddress 1.3.6.1.4.1.2011.5.25.111.2.2.1.23
Specifies the address of DNS server.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nqaAdminParaOperation 1.3.6.1.4.1.2011.5.25.111.2.2.1.24
Specifies the operation of FTP or HTTP type test instance. The operations of FTP-type test instance include get and put. The operations of HTTP-type test instance include get and post.
Status: current Access: read-write
OBJECT-TYPE    
  NqaOperation  

nqaAdminParaHttpVersion 1.3.6.1.4.1.2011.5.25.111.2.2.1.25
Specifies the version of HTTP.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

nqaAdminParaHttpOperationString 1.3.6.1.4.1.2011.5.25.111.2.2.1.26
A string that specifies the HTTP operation which will be sent to the HTTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

nqaAdminParaTestFailurePercent 1.3.6.1.4.1.2011.5.25.111.2.2.1.27
Specifies the scale over which the test will be regarded as failed.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

nqaAdminParaFtpUserName 1.3.6.1.4.1.2011.5.25.111.2.2.1.28
Specifies the user name of the FTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

nqaAdminParaFtpPassword 1.3.6.1.4.1.2011.5.25.111.2.2.1.29
Specifies the password of the user of the FTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

nqaAdminParaFtpFilePath 1.3.6.1.4.1.2011.5.25.111.2.2.1.30
Specifies the full name of the file which will be transmitted by the FTP-type test instance.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

nqaAdminParaFtpFileSize 1.3.6.1.4.1.2011.5.25.111.2.2.1.31
Specifies the size that the file will be transmitted by the FTP-type test instance. It may be part of the file.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10000  

nqaAdminParaInterval 1.3.6.1.4.1.2011.5.25.111.2.2.1.32
Specifies the interval between two consecutive probe packets.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..60000  

nqaAdminParaNumPackets 1.3.6.1.4.1.2011.5.25.111.2.2.1.33
Specifies the number of packet sent in each probe. This object is used together with nqaAdminParaProbeCount, and only apples to jitter-type test instance.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminParaVrfName 1.3.6.1.4.1.2011.5.25.111.2.2.1.34
Specifies the VRF name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

nqaAdminParaLspAddressType 1.3.6.1.4.1.2011.5.25.111.2.2.1.35
Specifies the address type of LSP. The object applies to lspping, lsptrace and lspjitter type test instance.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ipv4(1), te(3), ring(255)  

nqaAdminParaLspAddressMask 1.3.6.1.4.1.2011.5.25.111.2.2.1.36
Specifies the address mask of LSP. The object apples to lspping, lsptrace and lspjitter type test instance.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminParaLspIpAddress 1.3.6.1.4.1.2011.5.25.111.2.2.1.37
IP Address filled in the ip header, must be a 127/8 address.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nqaAdminParaLspPWE3VcId 1.3.6.1.4.1.2011.5.25.111.2.2.1.38
The local Pseudo wire ID in PWE3 Ping test
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

nqaAdminParaLspPWE3Type 1.3.6.1.4.1.2011.5.25.111.2.2.1.39
The encapsulation type of Pseudo wire ID in the PWE3 Ping test
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fr(1), atmAal5Sdu(2), atm-cell-transport(3), vlan(4), ethernet(5), hdlc(6), ppp(7), atm-nto1-vcc(9), atm-nto1-vpc(10), ip-layer2(11), atm-1to1-vcc(12), atm-1to1-vpc(13), satop-e1(17), satop-t1(18), satop-e3(19), cesopsn-basic(21), ipInterworking(64)  

nqaAdminParaLspPWE3Option 1.3.6.1.4.1.2011.5.25.111.2.2.1.40
The label type of PWE3 Ping and PWE3 Tracert test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER labelAlert(1), controlWord(2), normal(3)  

nqaAdminParaLspPWE3RemoteVcId 1.3.6.1.4.1.2011.5.25.111.2.2.1.41
The remote Pseudo wire ID in PWE Ping test.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

nqaAdminParaLspPWE3RemoteAddress 1.3.6.1.4.1.2011.5.25.111.2.2.1.42
The remote IP address in PWE3 Ping test.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nqaAdminParaLspExp 1.3.6.1.4.1.2011.5.25.111.2.2.1.43
The 3bit EXP field of the MPLS echo packet label.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..7  

nqaAdminParaLspReplyMode 1.3.6.1.4.1.2011.5.25.111.2.2.1.44
ReplyMode Value Meaning ----- ------- 1 Do not reply 2 Reply via an IPv4/IPv6 UDP packet 3 Reply via an IPv4/IPv6 UDP packet with Router Alert 4 Reply via application level control channel 5 Reply via a VPLS IPv4 UDP packet
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noReply(1), udp(2), udpRouterAlert(3), levelControlChannel(4), udpviaVPLS(5)  

nqaAdminParaResultRowMax 1.3.6.1.4.1.2011.5.25.111.2.2.1.45
Specifies the maximum number of result records.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminParaHistoryRowMax 1.3.6.1.4.1.2011.5.25.111.2.2.1.46
Specifies the maximum number of history records.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminParaCreateHopsEntries 1.3.6.1.4.1.2011.5.25.111.2.2.1.47
When set to 'enable (1)', the result of each hop will be kept in nqaResultsTable. The object applies to trace, pwe3trace, lsptrace, mtrace type test instance.
Status: current Access: read-write
OBJECT-TYPE    
  EnableValue  

nqaAdminParaLspVCType 1.3.6.1.4.1.2011.5.25.111.2.2.1.48
The type of protocol which establishes PW in the pwe3tracert test
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ldp(1), bgp(2), bgpad(3)  

nqaAdminParaMTraceLastHopAddress 1.3.6.1.4.1.2011.5.25.111.2.2.1.49
The last hop router's IP address in Mtrace test.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nqaAdminParaMTraceSourceAddress 1.3.6.1.4.1.2011.5.25.111.2.2.1.50
The IP address of the multicast source for the path being traced in Mtrace test.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nqaAdminParaMTraceGroupAddress 1.3.6.1.4.1.2011.5.25.111.2.2.1.51
The group address to be traced in Mtrace test, or zero if no group-specific information is desired.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nqaAdminParaMTraceMaxTtl 1.3.6.1.4.1.2011.5.25.111.2.2.1.52
The maximum number of hops that the requester wants to trace in Mtrace test.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

nqaAdminParaMTraceSendMode 1.3.6.1.4.1.2011.5.25.111.2.2.1.53
The sending mode of the Query pamessage in Mtrace test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER multicastTree(1), allRouter(2), destination(3), lastHop(4)  

nqaAdminParaMTraceResponseTtl 1.3.6.1.4.1.2011.5.25.111.2.2.1.54
The TTL at which to multicast the response in Mtrace test, if the response address is a multicast address.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

nqaAdminParaMTraceResponseAddressType 1.3.6.1.4.1.2011.5.25.111.2.2.1.55
Mtrace response address type
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

nqaAdminParaMTraceResponseAddress 1.3.6.1.4.1.2011.5.25.111.2.2.1.56
This field specifies where the completed traceroute response packet gets sent in Mtrace test. It can be a unicast address or a multicast address
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nqaAdminParaDistanceNodeType 1.3.6.1.4.1.2011.5.25.111.2.2.1.57
The destination of MAC ping(mac address or rmepid).
Status: current Access: read-write
OBJECT-TYPE    
  NqaDistanceNodeType  

nqaAdminParaMacAddress 1.3.6.1.4.1.2011.5.25.111.2.2.1.58
Mac address of the destination of MAC PING.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

nqaAdminParaRMepID 1.3.6.1.4.1.2011.5.25.111.2.2.1.59
Rmepid of the destination of MAC PING.
Status: current Access: read-write
OBJECT-TYPE    
  Dot1agCfmMepIdOrZero  

nqaAdminParaMDName 1.3.6.1.4.1.2011.5.25.111.2.2.1.60
Indicate the MD name in which the MAC Ping operated.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..43)  

nqaAdminParaMAName 1.3.6.1.4.1.2011.5.25.111.2.2.1.61
Indicate the MA name in which the MAC Ping operated.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..45)  

nqaAdminParaMacTunnelName 1.3.6.1.4.1.2011.5.25.111.2.2.1.62
Indicate the MAC Tunnel name in which the MAC Ping operated.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nqaAdminParaPathMtuStep 1.3.6.1.4.1.2011.5.25.111.2.2.1.63
Specify the step of the path MTU test.If the last response was received successful,the next packet's length will add the step.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..512  

nqaAdminParaPathMtuDiscoveryPathMtuMax 1.3.6.1.4.1.2011.5.25.111.2.2.1.64
Specify the max value of the discovery field in the path MTU test.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 48..9198  

nqaAdminParaIcmpJitterMode 1.3.6.1.4.1.2011.5.25.111.2.2.1.65
Select the type of ICMP packets to be sent in ICMP jitter and path jitter test.The value can be icmpTimestamp(1) or icmpEcho(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER icmpTimestamp(1), icmpEcho(2)  

nqaAdminParaCodecType 1.3.6.1.4.1.2011.5.25.111.2.2.1.66
To indicate the codec type to be used with jitter probe. This is applicable only for the jitter probe.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notDefined(1), g711Alaw(2), g711Ulaw(3), g729A(4)  

nqaAdminParaIcpifAdvFactor 1.3.6.1.4.1.2011.5.25.111.2.2.1.67
The advantage factor depends on the type of access and how the service is to be used. This object will be used while calculating the ICPIF (Calculated Planning Impairment Factor) values. Suggestion values: |---------------------------------------------------|-------| | Service |factor | |---------------------------------------------------|-------| | conventional wire-line | 0 | |---------------------------------------------------|-------| | mobility within Building | 5 | |---------------------------------------------------|-------| | mobility within geographical area | 10 | |---------------------------------------------------|-------| | access to hard-to-reach location | 20 | |---------------------------------------------------|-------|
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminParaFtpMode 1.3.6.1.4.1.2011.5.25.111.2.2.1.68
To indicate the mode to be used with ftp probe. This is applicable only for the ftp probe.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER active(1), passive(2)  

nqaAdminParaHardwareBased 1.3.6.1.4.1.2011.5.25.111.2.2.1.69
Indicates that the hardware is enabled to send packets. (The value range: enable:1;disable:2.The default value is disable(2))
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

nqaAdminParaPppoeUserName 1.3.6.1.4.1.2011.5.25.111.2.2.1.70
Specifies the username of PPPoE dial-up. For jitter,icmp,traceroute, tcp,udp,ftp,dns,http probes, this parameter indicates that the probe uses PPPoE encapsulation. This parameter accepts the characters in sight only.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

nqaAdminParaPppoePassword 1.3.6.1.4.1.2011.5.25.111.2.2.1.71
Specifies the password of PPPoE dial-up. This is applicable only for the PPPoE probe. This parameter accepts the characters in sight only.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

nqaAdminParaPppoeVlanIf 1.3.6.1.4.1.2011.5.25.111.2.2.1.72
Specifies the vlanif of PPPoE dial-up. For jitter, icmp, traceroute, tcp, udp, ftp, dns, http probes, this parameter indicates that the probe uses PPPoE encapsulation.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4093  

nqaAdminParaPppoeAuthenticationMode 1.3.6.1.4.1.2011.5.25.111.2.2.1.73
Specifies the authentication mode of PPPoE dial-up. This is applicable only for the PPPoE probe.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER chap(1), pap(2)  

nqaAdminParaPppoeRedialUpTimes 1.3.6.1.4.1.2011.5.25.111.2.2.1.74
Specifies the redialup times of PPPoE dial-up. This is applicable only for the PPPoE probe.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10  

nqaAdminParaPppoeInterval 1.3.6.1.4.1.2011.5.25.111.2.2.1.75
Specifies the redialup interval of PPPoE dial-up. This is applicable only for the PPPoE probe.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..600  

nqaAdminParaVsiName 1.3.6.1.4.1.2011.5.25.111.2.2.1.76
Specify the name of the VSI(Virtual Switch Instance)
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..31)  

nqaAdminParaVlanId 1.3.6.1.4.1.2011.5.25.111.2.2.1.77
Specify the Vlan ID
Status: current Access: read-write
OBJECT-TYPE    
  VlanIdOrNone  

nqaAdminParaLspTunnelType 1.3.6.1.4.1.2011.5.25.111.2.2.1.78
To indicate ping/trace which lsp tunnel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER main(0), hotstandby(1)  

nqaAdminParaLspNextHopAddress 1.3.6.1.4.1.2011.5.25.111.2.2.1.79
Represents the address of nexthop.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nqaAdminParaLspVersion 1.3.6.1.4.1.2011.5.25.111.2.2.1.80
Specify lsp version of protocol. Draft-ietf-mpls-lsp-ping-06 protocol, RFC4379 protocol or ptn mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER draft6(1), rfc4379(2), ptnmode(3)  

nqaAdminParaRemoteAddressType 1.3.6.1.4.1.2011.5.25.111.2.2.1.81
Represents the address type of remote.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

nqaAdminParaRemoteAddress 1.3.6.1.4.1.2011.5.25.111.2.2.1.82
Represents the address of remote.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nqaAdminParaTimeUnit 1.3.6.1.4.1.2011.5.25.111.2.2.1.83
The unit of the timestamp, ms or us.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER us(1), ms(2)  

nqaAdminParaExtTable 1.3.6.1.4.1.2011.5.25.111.2.5
Set parameter for a test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaAdminParaExtEntry

nqaAdminParaExtEntry 1.3.6.1.4.1.2011.5.25.111.2.5.1
Set parameter in the nqaAdminParaExtTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaAdminParaExtEntry  

nqaAdminExtPara1 1.3.6.1.4.1.2011.5.25.111.2.5.1.1
This object indicates the description of the nqaAdminExtPara2 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara2 1.3.6.1.4.1.2011.5.25.111.2.5.1.2
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara1 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara3 1.3.6.1.4.1.2011.5.25.111.2.5.1.3
This object indicates the description of the nqaAdminExtPara4 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara4 1.3.6.1.4.1.2011.5.25.111.2.5.1.4
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara3 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara5 1.3.6.1.4.1.2011.5.25.111.2.5.1.5
This object indicates the description of the nqaAdminExtPara6 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara6 1.3.6.1.4.1.2011.5.25.111.2.5.1.6
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara5 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara7 1.3.6.1.4.1.2011.5.25.111.2.5.1.7
This object indicates the description of the nqaAdminExtPara8 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara8 1.3.6.1.4.1.2011.5.25.111.2.5.1.8
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara7 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara9 1.3.6.1.4.1.2011.5.25.111.2.5.1.9
This object indicates the description of the nqaAdminExtPara10 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara10 1.3.6.1.4.1.2011.5.25.111.2.5.1.10
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara9 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara11 1.3.6.1.4.1.2011.5.25.111.2.5.1.11
This object indicates the description of the nqaAdminExtPara12 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara12 1.3.6.1.4.1.2011.5.25.111.2.5.1.12
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara11 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara13 1.3.6.1.4.1.2011.5.25.111.2.5.1.13
This object indicates the description of the nqaAdminExtPara14 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara14 1.3.6.1.4.1.2011.5.25.111.2.5.1.14
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara13 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara15 1.3.6.1.4.1.2011.5.25.111.2.5.1.15
This object indicates the description of the nqaAdminExtPara16 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara16 1.3.6.1.4.1.2011.5.25.111.2.5.1.16
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara15 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara17 1.3.6.1.4.1.2011.5.25.111.2.5.1.17
This object indicates the description of the nqaAdminExtPara18 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara18 1.3.6.1.4.1.2011.5.25.111.2.5.1.18
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara17 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara19 1.3.6.1.4.1.2011.5.25.111.2.5.1.19
This object indicates the description of the nqaAdminExtPara20 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara20 1.3.6.1.4.1.2011.5.25.111.2.5.1.20
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara19 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara21 1.3.6.1.4.1.2011.5.25.111.2.5.1.21
This object indicates the description of the nqaAdminExtPara22 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara22 1.3.6.1.4.1.2011.5.25.111.2.5.1.22
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara21 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara23 1.3.6.1.4.1.2011.5.25.111.2.5.1.23
This object indicates the description of the nqaAdminExtPara24 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara24 1.3.6.1.4.1.2011.5.25.111.2.5.1.24
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara23 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara25 1.3.6.1.4.1.2011.5.25.111.2.5.1.25
This object indicates the description of the nqaAdminExtPara26 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara26 1.3.6.1.4.1.2011.5.25.111.2.5.1.26
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara25 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara27 1.3.6.1.4.1.2011.5.25.111.2.5.1.27
This object indicates the description of the nqaAdminExtPara28 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara28 1.3.6.1.4.1.2011.5.25.111.2.5.1.28
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara27 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara29 1.3.6.1.4.1.2011.5.25.111.2.5.1.29
This object indicates the description of the nqaAdminExtPara30 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara30 1.3.6.1.4.1.2011.5.25.111.2.5.1.30
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara29 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaAdminExtPara31 1.3.6.1.4.1.2011.5.25.111.2.5.1.31
This object indicates the description of the nqaAdminExtPara32 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara32 1.3.6.1.4.1.2011.5.25.111.2.5.1.32
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara31 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara33 1.3.6.1.4.1.2011.5.25.111.2.5.1.33
This object indicates the description of the nqaAdminExtPara34 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara34 1.3.6.1.4.1.2011.5.25.111.2.5.1.34
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara33 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara35 1.3.6.1.4.1.2011.5.25.111.2.5.1.35
This object indicates the description of the nqaAdminExtPara36 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara36 1.3.6.1.4.1.2011.5.25.111.2.5.1.36
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara35 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara37 1.3.6.1.4.1.2011.5.25.111.2.5.1.37
This object indicates the description of the nqaAdminExtPara38 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara38 1.3.6.1.4.1.2011.5.25.111.2.5.1.38
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara37 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara39 1.3.6.1.4.1.2011.5.25.111.2.5.1.39
This object indicates the description of the nqaAdminExtPara40 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara40 1.3.6.1.4.1.2011.5.25.111.2.5.1.40
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara39 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara41 1.3.6.1.4.1.2011.5.25.111.2.5.1.41
This object indicates the description of the nqaAdminExtPara42 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara42 1.3.6.1.4.1.2011.5.25.111.2.5.1.42
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara41 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara43 1.3.6.1.4.1.2011.5.25.111.2.5.1.43
This object indicates the description of the nqaAdminExtPara44 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara44 1.3.6.1.4.1.2011.5.25.111.2.5.1.44
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara43 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara45 1.3.6.1.4.1.2011.5.25.111.2.5.1.45
This object indicates the description of the nqaAdminExtPara46 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara46 1.3.6.1.4.1.2011.5.25.111.2.5.1.46
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara45 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara47 1.3.6.1.4.1.2011.5.25.111.2.5.1.47
This object indicates the description of the nqaAdminExtPara48 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara48 1.3.6.1.4.1.2011.5.25.111.2.5.1.48
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara47 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara49 1.3.6.1.4.1.2011.5.25.111.2.5.1.49
This object indicates the description of the nqaAdminExtPara50 object. The value is automatically assigned by the system after the type of the test case is ascertained.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaAdminExtPara50 1.3.6.1.4.1.2011.5.25.111.2.5.1.50
This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara49 object after the test case is ascertained.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nqaScheduleTable 1.3.6.1.4.1.2011.5.25.111.2.3
Schedule test .
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaScheduleEntry

nqaScheduleEntry 1.3.6.1.4.1.2011.5.25.111.2.3.1
Set start-up in the nqaAdminParaTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaScheduleEntry  

nqaScheduleStartType 1.3.6.1.4.1.2011.5.25.111.2.3.1.1
Specifies the start type of the test instance. The object is used together with nqaScheduleStartTime.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), startNow(1), startAt(2), startAfter(3)  

nqaScheduleStartTime 1.3.6.1.4.1.2011.5.25.111.2.3.1.2
Specifies the start time of the test instance. Setting the value to 0 indicates to start the test instance immediately. After configuring this object, the status of the test instance is active, and the parameters of the test instance can't be changed.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

nqaScheduleEndType 1.3.6.1.4.1.2011.5.25.111.2.3.1.3
Specifies the end type of the test instance. The object is used together with nqaScheduleEndTime.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), endAt(1), endAfter(2), endLifetime(3)  

nqaScheduleEndTime 1.3.6.1.4.1.2011.5.25.111.2.3.1.4
Specifies the end time of the test instance.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

nqaScheduleAgeTime 1.3.6.1.4.1.2011.5.25.111.2.3.1.5
Specifies the aging time of the test instance, the time how long the test instance will be reserved in NQA, after the test instance is inactive. Setting the value to 0 indicates reserving the test instance eternally.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaScheduleElapsedTime 1.3.6.1.4.1.2011.5.25.111.2.3.1.6
The elapsed time (the period of time after task dispatch).
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

nqaScheduleNumOfInitiations 1.3.6.1.4.1.2011.5.25.111.2.3.1.7
Specifies the times that the test instance has been initialed. This object is used as the index of the result table, HTTP statistics table, jitter statistics table, FTP statistics table and history table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaScheduleLastFinishIndex 1.3.6.1.4.1.2011.5.25.111.2.3.1.8
Specifies the latest finished test of the test instance, which is used as the index of the result table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaScheduleOperStatus 1.3.6.1.4.1.2011.5.25.111.2.3.1.9
Specifies the status of dispatching operation: - reset: Clear all the records of the test instance. - stop: Stop the test instance, if it's running. - restart: Stop the test instance, if it's running, and restart the test instance immediately. - active: The test instance is running; the parameters of the test instances can't be changed. - inactive: The test instance doesn't be scheduled; the parameters of the test instances can be changed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), stop(2), restart(3), active(4), inactive(5)  

nqaScheduleLastCollectIndex 1.3.6.1.4.1.2011.5.25.111.2.3.1.10
Specifies the index of the latest collection statistics result record in the collection result table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaGroupTable 1.3.6.1.4.1.2011.5.25.111.2.4
Set group for a test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaGroupEntry

nqaGroupEntry 1.3.6.1.4.1.2011.5.25.111.2.4.1
Set parameters in the nqaGroupTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaGroupEntry  

nqaGroupStatusType 1.3.6.1.4.1.2011.5.25.111.2.4.1.1
Specifies the group status of the test instance. The value can be normal (1), leader (2) or member (3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), leader(2), member(3)  

nqaGroupPeriod 1.3.6.1.4.1.2011.5.25.111.2.4.1.2
Specifies the interval during which all members in the specified group will be executed.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

nqaGroupLeaderOwnerIndex 1.3.6.1.4.1.2011.5.25.111.2.4.1.3
Specifies the owner index of the group leader, if the test instance is a member of the group.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

nqaGroupLeaderTestName 1.3.6.1.4.1.2011.5.25.111.2.4.1.4
Specifies the test name of the group leader, if the test instance is a member of the group.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

nqaGroupMemberNum 1.3.6.1.4.1.2011.5.25.111.2.4.1.5
Specifies the number of member in the group.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaGroupMemberFree 1.3.6.1.4.1.2011.5.25.111.2.4.1.6
Free all members in the group.
Status: current Access: read-write
OBJECT-TYPE    
  EnableValue  

nqaServer 1.3.6.1.4.1.2011.5.25.111.3
OBJECT IDENTIFIER    

nqaServerEnable 1.3.6.1.4.1.2011.5.25.111.3.1
Enables NQA server, which can be the echo server of TCP, UDP and jitter type test instance.
Status: current Access: read-write
OBJECT-TYPE    
  EnableValue  

nqaTcpServerTable 1.3.6.1.4.1.2011.5.25.111.3.2
A table which contains the status of nqa tcp server configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaTcpServerEntry

nqaTcpServerEntry 1.3.6.1.4.1.2011.5.25.111.3.2.1
A table which contains the status of nqa tcp server configuration information. This entry is included not only the tcp server ip address but also the tcp server tcp port. If used for VPN it is also included the VPN name.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaTcpServerEntry  

nqaTcpServerAddressType 1.3.6.1.4.1.2011.5.25.111.3.2.1.1
Specifies the address type of TCP server.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

nqaTcpServerAddress 1.3.6.1.4.1.2011.5.25.111.3.2.1.2
Specifies the address of TCP server.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

nqaTcpServerPort 1.3.6.1.4.1.2011.5.25.111.3.2.1.3
Specifies the port number on which TCP server is listening.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetPortNumber  

nqaTcpServerVrfName 1.3.6.1.4.1.2011.5.25.111.3.2.1.4
Specifies the VRF (VPN Routing & Forwarding) instances name of the TCP server.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

nqaTcpServerStatus 1.3.6.1.4.1.2011.5.25.111.3.2.1.5
Specifies the operation of the TCP server, creating or deleting.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

nqaUdpServerTable 1.3.6.1.4.1.2011.5.25.111.3.3
A table which contains the status of nqa udp server configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaUdpServerEntry

nqaUdpServerEntry 1.3.6.1.4.1.2011.5.25.111.3.3.1
A table which contains the status of nqa udp server configuration information. This entry is includeed not only the udp server ip address but also the udp server udp port.If used for VPN it is also included the VPN name.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaUdpServerEntry  

nqaUdpServerAddressType 1.3.6.1.4.1.2011.5.25.111.3.3.1.1
Specifies the address type of UDP server.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

nqaUdpServerAddress 1.3.6.1.4.1.2011.5.25.111.3.3.1.2
Specifies the address of UDP server.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

nqaUdpServerPort 1.3.6.1.4.1.2011.5.25.111.3.3.1.3
Specifies the port number on which UDP server is listening.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetPortNumber  

nqaUdpServerVrfName 1.3.6.1.4.1.2011.5.25.111.3.3.1.4
Specifies the VRF (VPN Routing & Forwarding) instances name of the UDP server.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

nqaUdpServerStatus 1.3.6.1.4.1.2011.5.25.111.3.3.1.5
Specifies the operation of the UDP server, creating or deleting.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

nqaIcmpServerTable 1.3.6.1.4.1.2011.5.25.111.3.4
A table which contains the status of nqa ICMP server configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaIcmpServerEntry

nqaIcmpServerEntry 1.3.6.1.4.1.2011.5.25.111.3.4.1
A table which contains the status of nqa ICMP server configuration information. This entry is included the ICMP server IP address. If used for VPN it is also included the VPN name.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaIcmpServerEntry  

nqaIcmpServerAddress 1.3.6.1.4.1.2011.5.25.111.3.4.1.1
Specifies the address of ICMP server.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

nqaIcmpServerVrfName 1.3.6.1.4.1.2011.5.25.111.3.4.1.2
Specifies the VRF (VPN Routing & Forwarding) instances name of the ICMP server.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

nqaIcmpServerAddressType 1.3.6.1.4.1.2011.5.25.111.3.4.1.3
Specifies the address type of ICMP server.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

nqaIcmpServerStatus 1.3.6.1.4.1.2011.5.25.111.3.4.1.51
Specifies the operation of the ICMP server, creating or deleting.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

nqaStats 1.3.6.1.4.1.2011.5.25.111.4
OBJECT IDENTIFIER    

nqaResultsTable 1.3.6.1.4.1.2011.5.25.111.4.1
Defines the test Results Extend Table for providing the capability of performing test operations at a remote host. The results of these operations are stored in the nqaResultsTable . The operation of this table is same as that of nqaResultsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaResultsEntry

nqaResultsEntry 1.3.6.1.4.1.2011.5.25.111.4.1.1
The operation of this table is same as that of nqaResultsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaResultsEntry  

nqaResultsIndex 1.3.6.1.4.1.2011.5.25.111.4.1.1.1
The result table index and times of dispatching dependency tests. Each test can only reserve 5 records. The result table only contains icmp/dns/dlsw/lspPing/Traceroute/LSP Traceroute/tcp/udp/snmp/dhcp Traceroute information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaResultsHopIndex 1.3.6.1.4.1.2011.5.25.111.4.1.1.2
The hop index. If the test type is Traceroute or LSP Traceroute, the entry only defines one hop. For other types, the default value is 1.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..255  

nqaResultsCompletions 1.3.6.1.4.1.2011.5.25.111.4.1.1.3
The status of test.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noResult(0), success(1), failure(2)  

nqaResultsTestAttempts 1.3.6.1.4.1.2011.5.25.111.4.1.1.4
The times of executing tests, which includes the times of successful execution, failed execution and interruption (interrupted by human or system). The current number of test attempts. The value of this object MUST be started at 0.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaResultsCurHopCount 1.3.6.1.4.1.2011.5.25.111.4.1.1.5
It is equal to the hop count index executed by current Traceroute or LSP Traceroute tests. Ping/LSP Ping does not use this entry. The default value is 0.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaResultsCurProbeCount 1.3.6.1.4.1.2011.5.25.111.4.1.1.6
The total count of probe packets of Traceroute or LSP Traceroute test in a hop count index.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaResultsRTDOverThresholds 1.3.6.1.4.1.2011.5.25.111.4.1.1.7
The times of successful statistics test RTD (Round Trip Delay) over the threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaResultsSumCompletionTime 1.3.6.1.4.1.2011.5.25.111.4.1.1.8
The sum of RTT (response time) of all packets of each hop for executing Traceroute, LSP Traceroute tests. The sum of RTT (response time) of sent packets for executing ping, lsp ping and disman-ping tests and so on.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaResultsSumCompletionTime2Low 1.3.6.1.4.1.2011.5.25.111.4.1.1.9
The low order 32 bits of the accumulated squares of completion times (in milliseconds) of NQA operations which complete successfully. Low/High order is defined where the binary number will look as follows: ------------------------------------------------- | High order 32 bits | Low order 32 bits | ------------------------------------------------- For example the number 4294967296 would have all Low order bits as '0' and the rightmost High order bit will be 1 (zeros,1).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaResultsSumCompletionTime2High 1.3.6.1.4.1.2011.5.25.111.4.1.1.10
The high order 32 bits of the accumulated squares of completion times (in milliseconds) of NQA operations which complete successfully. See the nqaResultsSumCompletionTime2Low object for a definition of Low/High Order.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaResultsCompletionTimeMin 1.3.6.1.4.1.2011.5.25.111.4.1.1.11
The minimum RTT (for Traceroute and LSP Traceroute, it is the minimum RTT among all the packet of next hop) of all packets for executing a test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaResultsCompletionTimeMax 1.3.6.1.4.1.2011.5.25.111.4.1.1.12
The maximum RTT (for Traceroute and LSP Traceroute, it is the maximum RTT among all the packets of next hop) of all packets in executing a test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaResultsDisconnects 1.3.6.1.4.1.2011.5.25.111.4.1.1.13
The times of consecutive failures. For connectionless protocol type of test,this number should be zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaResultsTimeouts 1.3.6.1.4.1.2011.5.25.111.4.1.1.14
The number of occasions when a NQA operation was not completed before a timeout occurred, i.e. nqaAdminCtrlTimeOut was exceeded.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaResultsBusies 1.3.6.1.4.1.2011.5.25.111.4.1.1.15
The times of failure to apply resource due to the busy system. such as apply memory or create socket failure.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaResultsNoConnections 1.3.6.1.4.1.2011.5.25.111.4.1.1.16
The number of occasions when a NQA operation could not be initiated because the connection to the target has not been established. For all other nqaAdminCtrlType this object will remain zero. This cannot occur for connectionless protocols, but may occur for connection oriented protocols, such as TCP. Since a NQA operation was never initiated, the completion time of these operations are not accumulated, nor do they increment nqaResultsCompletions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaResultsSequenceErrors 1.3.6.1.4.1.2011.5.25.111.4.1.1.17
The number of NQA operation completions received with an unexpected sequence identifier. For all other values of nqaAdminCtrlType this object will remain zero. When this has occurred some of the possible reasons maybe: - a duplicate packet was received - a response was received after it had timed-out - a corrupted packet was received and was not detected
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaResultsDrops 1.3.6.1.4.1.2011.5.25.111.4.1.1.18
The times probes of the test dropped due to sending or connecting failure.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaResultsAddressType 1.3.6.1.4.1.2011.5.25.111.4.1.1.19
The destination address type, and the value range can be unknown(0), ipv4(1) and dns(16).
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

nqaResultsAddress 1.3.6.1.4.1.2011.5.25.111.4.1.1.20
The destination address (TraceRoute is the destination address of each hop, and ping is the destination address of tests).
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaResultsProbeResponses 1.3.6.1.4.1.2011.5.25.111.4.1.1.21
Number of responses received for the corresponding test. The value of this object MUST be reported as 0 when no probe responses have been received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaResultsSentProbes 1.3.6.1.4.1.2011.5.25.111.4.1.1.22
The value of this object reflects the number of probes sent for the corresponding test. The value of this object MUST be reported as 0 when no probes have been sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaResultsLastGoodProbe 1.3.6.1.4.1.2011.5.25.111.4.1.1.23
Date and time when the last response was received for a probe.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

nqaResultsLastGoodPath 1.3.6.1.4.1.2011.5.25.111.4.1.1.24
The date and time when the last complete path was determined.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

nqaResultsTestFinished 1.3.6.1.4.1.2011.5.25.111.4.1.1.25
The status of test execution.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noFinish(0), finish(1)  

nqaResultsRttAvg 1.3.6.1.4.1.2011.5.25.111.4.1.1.26
The average of RTTs that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaResultsLostPacketRatio 1.3.6.1.4.1.2011.5.25.111.4.1.1.27
The ratio of the packets lost to all packets sent in the test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaHTTPStatsTable 1.3.6.1.4.1.2011.5.25.111.4.2
The statistics collection database. Defines the HTTP Operations Statistics Table for storing the statistics of a HTTP test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaHTTPStatsEntry

nqaHTTPStatsEntry 1.3.6.1.4.1.2011.5.25.111.4.2.1
Defines an entry in the nqaHTTPStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaHTTPStatsEntry  

nqaHTTPStatsIndex 1.3.6.1.4.1.2011.5.25.111.4.2.1.1
The The HTTP statistics table index and times of dispatching dependency tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaHTTPStatsCompletions 1.3.6.1.4.1.2011.5.25.111.4.2.1.2
The status of HTTP test.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noResult(0), success(1), failure(2)  

nqaHTTPStatsRTDOverThresholds 1.3.6.1.4.1.2011.5.25.111.4.2.1.3
The number of HTTP operations RTD (Round Trip Delay) that violate threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsRTTSum 1.3.6.1.4.1.2011.5.25.111.4.2.1.4
The sum of delay time of successful HTTP probes, including the sum of time of DNS query, TCP establishment and packets transmission.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsRTTMin 1.3.6.1.4.1.2011.5.25.111.4.2.1.5
The minimum value of HTTP probe time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaHTTPStatsRTTMax 1.3.6.1.4.1.2011.5.25.111.4.2.1.6
The maximum value of HTTP probe time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaHTTPStatsDNSRTTSum 1.3.6.1.4.1.2011.5.25.111.4.2.1.7
The sum of DNS query time.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsDNSRTTMin 1.3.6.1.4.1.2011.5.25.111.4.2.1.8
The minimum of DNS query time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaHTTPStatsDNSRTTMax 1.3.6.1.4.1.2011.5.25.111.4.2.1.9
The maximum of DNS query time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaHTTPStatsTCPConnectRTTSum 1.3.6.1.4.1.2011.5.25.111.4.2.1.10
The sum of TCP connection time.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsTCPConnectRTTMin 1.3.6.1.4.1.2011.5.25.111.4.2.1.11
The minimum value of TCP connection time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaHTTPStatsTCPConnectRTTMax 1.3.6.1.4.1.2011.5.25.111.4.2.1.12
The maximum value of TCP connection time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaHTTPStatsTransactionRTTSum 1.3.6.1.4.1.2011.5.25.111.4.2.1.13
The sum of transaction time.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsTransactionRTTMin 1.3.6.1.4.1.2011.5.25.111.4.2.1.14
The minimum value of transaction time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaHTTPStatsTransactionRTTMax 1.3.6.1.4.1.2011.5.25.111.4.2.1.15
The maximum value of transaction time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaHTTPStatsMessageBodyOctetsSum 1.3.6.1.4.1.2011.5.25.111.4.2.1.16
The sum of the size of the message body received as a response to the HTTP request.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsDNSServerTimeouts 1.3.6.1.4.1.2011.5.25.111.4.2.1.17
The number of requests that timed out during DNS query.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsTCPConnectTimeouts 1.3.6.1.4.1.2011.5.25.111.4.2.1.18
The number of requests that timed out during HTTP connection.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsTransactionTimeouts 1.3.6.1.4.1.2011.5.25.111.4.2.1.19
The number of requests that timed out during HTTP transaction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsDNSQueryErrors 1.3.6.1.4.1.2011.5.25.111.4.2.1.20
The number of requests that had DNS query errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsErrors 1.3.6.1.4.1.2011.5.25.111.4.2.1.21
The number of HTTP transaction failures.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsTcpConnErrors 1.3.6.1.4.1.2011.5.25.111.4.2.1.22
The number of TCP connection failures.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsProbeResponses 1.3.6.1.4.1.2011.5.25.111.4.2.1.23
Number of responses received for the corresponding test. The value of this object MUST be reported as 0 when no probe responses have been received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsSendProbes 1.3.6.1.4.1.2011.5.25.111.4.2.1.24
The number of sending probes.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsBusies 1.3.6.1.4.1.2011.5.25.111.4.2.1.25
The number of occasions when a HTTP operation could not be initiated because an internal error.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaHTTPStatsTestFinished 1.3.6.1.4.1.2011.5.25.111.4.2.1.26
The status of test execution.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noFinish(0), finish(1)  

nqaHTTPStatsRttAvg 1.3.6.1.4.1.2011.5.25.111.4.2.1.27
The average of RTTs that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaHTTPStatsLostPacketRatio 1.3.6.1.4.1.2011.5.25.111.4.2.1.28
The ratio of the packets lost to all packets sent in the test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsTable 1.3.6.1.4.1.2011.5.25.111.4.3
A table which contains the status of latest Jitter operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaJitterStatsEntry

nqaJitterStatsEntry 1.3.6.1.4.1.2011.5.25.111.4.3.1
A table which contains the status of latest Jitter operation. This entry is created only if the nqaAdminCtrlType is jitterAppl.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaJitterStatsEntry  

nqaJitterStatsIndex 1.3.6.1.4.1.2011.5.25.111.4.3.1.1
The third index of jitter statistics table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaJitterStatsCompletions 1.3.6.1.4.1.2011.5.25.111.4.3.1.2
The result of the test, which value can be noResult (0), success (1), failure (2) or negotiateFailed (3). If the test is still running, the value will be noResult (0).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noResult(0), success(1), failure(2), negotiateFailed(3)  

nqaJitterStatsRTDOverThresholds 1.3.6.1.4.1.2011.5.25.111.4.3.1.3
The number of tests that violate RTD (Round Trip Delay) threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsNumOfRTT 1.3.6.1.4.1.2011.5.25.111.4.3.1.4
The number of RTTs that are successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsRTTSum 1.3.6.1.4.1.2011.5.25.111.4.3.1.5
The sum of RTTs that are successfully measured.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsRTTSum2Low 1.3.6.1.4.1.2011.5.25.111.4.3.1.6
The sum of squares of RTTs that are successfully measured by tests (low order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsRTTSum2High 1.3.6.1.4.1.2011.5.25.111.4.3.1.7
The sum of squares of RTTs that are successfully measured by tests (high order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsRTTMin 1.3.6.1.4.1.2011.5.25.111.4.3.1.8
The minimum of RTTs that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsRTTMax 1.3.6.1.4.1.2011.5.25.111.4.3.1.9
The maximum of RTTs that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsMinOfPositivesSD 1.3.6.1.4.1.2011.5.25.111.4.3.1.10
The minimum of absolute value of all positive jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsMaxOfPositivesSD 1.3.6.1.4.1.2011.5.25.111.4.3.1.11
The maximum of absolute value of all positive jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsNumOfPositivesSD 1.3.6.1.4.1.2011.5.25.111.4.3.1.12
The number of all positive jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsSumOfPositivesSD 1.3.6.1.4.1.2011.5.25.111.4.3.1.13
The sum of absolute value of all positive jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsSum2OfPositivesSDLow 1.3.6.1.4.1.2011.5.25.111.4.3.1.14
The sum of squares of absolute value of all positive jitter values from source to destination (low order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsSum2OfPositivesSDHigh 1.3.6.1.4.1.2011.5.25.111.4.3.1.15
The sum of squares of absolute value of all positive jitter values from source to destination (high order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsMinOfNegativesSD 1.3.6.1.4.1.2011.5.25.111.4.3.1.16
The minimum of absolute value of all negative jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsMaxOfNegativesSD 1.3.6.1.4.1.2011.5.25.111.4.3.1.17
The maximum of absolute value of all negative jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsNumOfNegativesSD 1.3.6.1.4.1.2011.5.25.111.4.3.1.18
The number of all negative jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsSumOfNegativesSD 1.3.6.1.4.1.2011.5.25.111.4.3.1.19
The sum of absolute value of all negative jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsSum2OfNegativesSDLow 1.3.6.1.4.1.2011.5.25.111.4.3.1.20
The sum of squares of absolute value of all negative values from source to destination (low order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsSum2OfNegativesSDHigh 1.3.6.1.4.1.2011.5.25.111.4.3.1.21
The sum of squares of absolute value of all negative values from source to destination (high order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsMinOfPositivesDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.22
The minimum of absolute value of all positive jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsMaxOfPositivesDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.23
The maximum of absolute value of all positive jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsNumOfPositivesDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.24
The number of all positive jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsSumOfPositivesDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.25
The sum of absolute value of all positive jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsSum2OfPositivesDSLow 1.3.6.1.4.1.2011.5.25.111.4.3.1.26
The sum of squares of absolute value of all positive jitter values from destination to source (low order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsSum2OfPositivesDSHigh 1.3.6.1.4.1.2011.5.25.111.4.3.1.27
The sum of squares of absolute value of all positive jitter values from destination to source (high order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsMinOfNegativesDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.28
The minimum of absolute value of all negative jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsMaxOfNegativesDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.29
The maximum of absolute value of all negative jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsNumOfNegativesDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.30
The number of all negative jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsSumOfNegativesDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.31
The sum of absolute value of all negative jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsSum2OfNegativesDSLow 1.3.6.1.4.1.2011.5.25.111.4.3.1.32
The sum of squares of absolute value of all negative values from destination to source (low order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsSum2OfNegativesDSHigh 1.3.6.1.4.1.2011.5.25.111.4.3.1.33
The sum of squares of absolute value of all negative values from destination to source (high order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsPacketLossSD 1.3.6.1.4.1.2011.5.25.111.4.3.1.34
The number of packets lost when sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsPacketLossDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.35
The number of packets lost when sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsPacketOutOfSequences 1.3.6.1.4.1.2011.5.25.111.4.3.1.36
The number of packets arrived out of sequence.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsErrors 1.3.6.1.4.1.2011.5.25.111.4.3.1.37
The number of errors occurred in the test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsBusies 1.3.6.1.4.1.2011.5.25.111.4.3.1.38
The number of occasions when a test couldn't be initialized because the previous test has not completed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsTimeouts 1.3.6.1.4.1.2011.5.25.111.4.3.1.39
The number of responses arrived over the time.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsProbeResponses 1.3.6.1.4.1.2011.5.25.111.4.3.1.40
The number of responses from echo-server for the packets sent by the test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsSentProbes 1.3.6.1.4.1.2011.5.25.111.4.3.1.41
The number of packets sent in the test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsDrops 1.3.6.1.4.1.2011.5.25.111.4.3.1.42
The number of packets that were sent failed in the test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsTestFinished 1.3.6.1.4.1.2011.5.25.111.4.3.1.43
The status of the test, which value can be noFinish (0) or finish (1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noFinish(0), finish(1)  

nqaJitterStatsMaxDelaySD 1.3.6.1.4.1.2011.5.25.111.4.3.1.44
The maximum of all OWD (One Way Delay) from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsMaxDelayDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.45
The maximum of all OWD (One Way Delay) from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsRTTAvg 1.3.6.1.4.1.2011.5.25.111.4.3.1.46
The average of RTTs that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsPacketLossRatio 1.3.6.1.4.1.2011.5.25.111.4.3.1.47
The ratio of the packets lost to all packets sent in the test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsAvgJitter 1.3.6.1.4.1.2011.5.25.111.4.3.1.48
The average of jitter values that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsAvgJitterSD 1.3.6.1.4.1.2011.5.25.111.4.3.1.49
The average of jitter values from source to destination that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsAvgJitterDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.50
The average of jitter values from destination to source that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsJitterOut 1.3.6.1.4.1.2011.5.25.111.4.3.1.51
Jitter (RFC1889) at responder.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaJitterStatsJitterIn 1.3.6.1.4.1.2011.5.25.111.4.3.1.52
Jitter (RFC1889) at sender.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaJitterStatsOWDOverThresholdsSD 1.3.6.1.4.1.2011.5.25.111.4.3.1.53
The number of tests that violate OWD (One Way Delay) threshold from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsPktLossUnknown 1.3.6.1.4.1.2011.5.25.111.4.3.1.54
The number of packets lost for which we can't determine the direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsNumOfOWD 1.3.6.1.4.1.2011.5.25.111.4.3.1.55
The number of OWDs that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsOWSumSD 1.3.6.1.4.1.2011.5.25.111.4.3.1.56
The sum of OWDs that were successfully measured by tests from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsOWSumDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.57
The sum of OWDs that were successfully measured by tests from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsOWDOverThresholdsDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.58
The number of tests that violate OWD (One Way Delay) threshold from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsOperOfIcpif 1.3.6.1.4.1.2011.5.25.111.4.3.1.59
The ICPIF (Calculated Planning Impairment Factor) value for the latest jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsOperOfMos 1.3.6.1.4.1.2011.5.25.111.4.3.1.60
The MOS (Mean Opinion Score) value for the latest jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsMinDelaySD 1.3.6.1.4.1.2011.5.25.111.4.3.1.61
The minimum of all one way time from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsSum2DelaySDLow 1.3.6.1.4.1.2011.5.25.111.4.3.1.62
The low order 32 bits of the sum of squares of one way time from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsSum2DelaySDHigh 1.3.6.1.4.1.2011.5.25.111.4.3.1.63
The high order 32 bits of the sum of squares of one way time from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsMinDelayDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.64
The minimum of all one way time from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsSum2DelayDSLow 1.3.6.1.4.1.2011.5.25.111.4.3.1.65
The low order 32 bits of the sum of squares of one way time from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsSum2DelayDSHigh 1.3.6.1.4.1.2011.5.25.111.4.3.1.66
The low order 32 bits of the sum of squares of one way time from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsTimeUnit 1.3.6.1.4.1.2011.5.25.111.4.3.1.67
The unit of the timestamp, ms or us.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER us(1), ms(2)  

nqaJitterStatsAvgDelaySD 1.3.6.1.4.1.2011.5.25.111.4.3.1.68
The average of one way time from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsAvgDelayDS 1.3.6.1.4.1.2011.5.25.111.4.3.1.69
The average of one way time from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsPktRewriteNum 1.3.6.1.4.1.2011.5.25.111.4.3.1.70
The number of packets have been rewrited.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsPktRewriteRatio 1.3.6.1.4.1.2011.5.25.111.4.3.1.71
The ratio of packets have been rewrited.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsPktDisorderNum 1.3.6.1.4.1.2011.5.25.111.4.3.1.72
The number of packets have been disordered.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsPktDisorderRatio 1.3.6.1.4.1.2011.5.25.111.4.3.1.73
The ratio of packets have been disordered.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterStatsFragPktDisorderNum 1.3.6.1.4.1.2011.5.25.111.4.3.1.74
The number of packets whose fragments have been disordered.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterStatsFragPktDisorderRatio 1.3.6.1.4.1.2011.5.25.111.4.3.1.75
The ratio of packets whose fragments have been disordered.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaFTPStatsTable 1.3.6.1.4.1.2011.5.25.111.4.4
The statistics collection database. Defines the FTP Operations Statistics Table for storing the statistics of a FTP test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaFTPStatsEntry

nqaFTPStatsEntry 1.3.6.1.4.1.2011.5.25.111.4.4.1
Defines an entry in the nqaFTPStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaFTPStatsEntry  

nqaFTPStatsIndex 1.3.6.1.4.1.2011.5.25.111.4.4.1.1
FTP statistics table index and times of dispatching dependency tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaFTPStatsCompletions 1.3.6.1.4.1.2011.5.25.111.4.4.1.2
The status of FTP test.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noResult(0), success(1), failure(2)  

nqaFTPStatsRTDOverThresholds 1.3.6.1.4.1.2011.5.25.111.4.4.1.3
The times of successful statistics test RTD (Round Trip Delay) over the threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaFTPStatsCtrlConnMaxTime 1.3.6.1.4.1.2011.5.25.111.4.4.1.4
The maximum value of the control connection time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaFTPStatsCtrlConnMinTime 1.3.6.1.4.1.2011.5.25.111.4.4.1.5
The minimum value of the control connection time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaFTPStatsCtrlConnAveTime 1.3.6.1.4.1.2011.5.25.111.4.4.1.6
The average value of the control connection time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaFTPStatsDataConnMaxTime 1.3.6.1.4.1.2011.5.25.111.4.4.1.7
The maximum value of the data connection time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaFTPStatsDataConnMinTime 1.3.6.1.4.1.2011.5.25.111.4.4.1.8
The minimum value of the data connection time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaFTPStatsDataConnAveTime 1.3.6.1.4.1.2011.5.25.111.4.4.1.9
The average value of the data connection time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaFTPStatsConnectSumTimeMax 1.3.6.1.4.1.2011.5.25.111.4.4.1.10
The maximum value of the FTP probe time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaFTPStatsConnectSumTimeMin 1.3.6.1.4.1.2011.5.25.111.4.4.1.11
The mininum value of the FTP probe time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaFTPStatsConnectSumTimeAve 1.3.6.1.4.1.2011.5.25.111.4.4.1.12
The average value of the FTP probe time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaFTPStatsMessageBodyOctetsSum 1.3.6.1.4.1.2011.5.25.111.4.4.1.13
The accumulated octets of a FTP test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaFTPStatsErrors 1.3.6.1.4.1.2011.5.25.111.4.4.1.14
The number of some other errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaFTPStatsTimeouts 1.3.6.1.4.1.2011.5.25.111.4.4.1.15
The number of occasions when a FTP operation was not completed before a timeout occurred, i.e. nqaAdminCtrlTimeOut was exceeded.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaFTPStatsDiscontinued 1.3.6.1.4.1.2011.5.25.111.4.4.1.16
The number of occasions when a FTP test was interrupted by the user.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaFTPStatsProbeResponses 1.3.6.1.4.1.2011.5.25.111.4.4.1.17
Number of responses received for the corresponding test. The value of this object MUST be reported as 0 when no probe responses have been received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaFTPStatsSendProbes 1.3.6.1.4.1.2011.5.25.111.4.4.1.18
The number of sending probe
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaFTPStatsTestFinished 1.3.6.1.4.1.2011.5.25.111.4.4.1.19
The status of test execution.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noFinish(0), finish(1)  

nqaFTPStatsRttAvg 1.3.6.1.4.1.2011.5.25.111.4.4.1.20
The average of RTTs that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaFTPStatsLostPacketRatio 1.3.6.1.4.1.2011.5.25.111.4.4.1.21
The ratio of the packets lost to all packets sent in the test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMpingStatsTable 1.3.6.1.4.1.2011.5.25.111.4.5
The statistics collection database. Defines the Mping Operations Statistics Table for storing the statistics of a Mping test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaMpingStatsEntry

nqaMpingStatsEntry 1.3.6.1.4.1.2011.5.25.111.4.5.1
Defines an entry in the nqaMpingStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaMpingStatsEntry  

nqaMpingStatsIndex 1.3.6.1.4.1.2011.5.25.111.4.5.1.1
The index of mping statistics table, and the times of dispatching dependency tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaMpingStatsReceiverIndex 1.3.6.1.4.1.2011.5.25.111.4.5.1.2
The index of receiver ,that received the mping request packet and response the reply packet .
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaMpingStatsTargetAddressType 1.3.6.1.4.1.2011.5.25.111.4.5.1.3
The destination address type, and the value range can be unknown(0), ipv4(1) and dns(16).
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

nqaMpingStatsTargetAddress 1.3.6.1.4.1.2011.5.25.111.4.5.1.4
The destination address .
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaMpingStatsReceiverAddress 1.3.6.1.4.1.2011.5.25.111.4.5.1.5
The address of mping receiver
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaMpingStatsCompletions 1.3.6.1.4.1.2011.5.25.111.4.5.1.6
The status of test.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noResult(1), success(2), failure(3)  

nqaMpingStatsRTDOverThresholds 1.3.6.1.4.1.2011.5.25.111.4.5.1.7
The times of successful statistics test RTD (Round Trip Delay) over the threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMpingStatsSumCompletionTime 1.3.6.1.4.1.2011.5.25.111.4.5.1.8
The sum of RTT (response time) of sent packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMpingStatsSumCompletionTime2Low 1.3.6.1.4.1.2011.5.25.111.4.5.1.9
The low order 32 bits of the sum of squares of RTT (response time) for each packet of test execution.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMpingStatsSumCompletionTime2High 1.3.6.1.4.1.2011.5.25.111.4.5.1.10
The high order 32 bits of the sum of squares of RTT (response time) for each packet of test execution.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMpingStatsCompletionTimeMin 1.3.6.1.4.1.2011.5.25.111.4.5.1.11
The minimum RTT of all packets for executing a test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMpingStatsCompletionTimeMax 1.3.6.1.4.1.2011.5.25.111.4.5.1.12
The maximum RTT of all packets in executing a test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMpingStatsTimeouts 1.3.6.1.4.1.2011.5.25.111.4.5.1.13
The number of occasions when a NQA operation was not completed before a timeout occurred, i.e. nqaAdminCtrlTimeOut was exceeded.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMpingStatsBusies 1.3.6.1.4.1.2011.5.25.111.4.5.1.14
The times of failure to apply resource due to the busy system. such as apply memory or create socket failure.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMpingStatsSequenceErrors 1.3.6.1.4.1.2011.5.25.111.4.5.1.15
The times that sequence error happends.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMpingStatsDrops 1.3.6.1.4.1.2011.5.25.111.4.5.1.16
The times probes of the test dropped due to sending or connecting failure .
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMpingStatsProbeResponses 1.3.6.1.4.1.2011.5.25.111.4.5.1.17
The number of received reponse packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMpingStatsSentProbes 1.3.6.1.4.1.2011.5.25.111.4.5.1.18
The number of sent packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMpingStatsLastGoodProbe 1.3.6.1.4.1.2011.5.25.111.4.5.1.19
Date and time when the last response was received for a probe.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

nqaMpingStatsTestFinished 1.3.6.1.4.1.2011.5.25.111.4.5.1.20
The status of test execution.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noFinish(1), finish(2)  

nqaMpingStatsReceiverCount 1.3.6.1.4.1.2011.5.25.111.4.5.1.21
The current serial number of receivers.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMpingStatsLastFibHit 1.3.6.1.4.1.2011.5.25.111.4.5.1.22
Whether the fib is hit on the device when receiving the last packet.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

nqaMpingStatsRttAvg 1.3.6.1.4.1.2011.5.25.111.4.5.1.23
The average of RTTs that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMpingStatsLostPacketRatio 1.3.6.1.4.1.2011.5.25.111.4.5.1.24
The ratio of the packets lost to all packets sent in the test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMtracertStatsTable 1.3.6.1.4.1.2011.5.25.111.4.6
The statistics collection database. Defines the Mping Operations Statistics Table for storing the statistics of a Mping test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaMtracertStatsEntry

nqaMtracertStatsEntry 1.3.6.1.4.1.2011.5.25.111.4.6.1
The operation of this table is same as that of nqaResultsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaMtracertStatsEntry  

nqaMtracertStatsIndex 1.3.6.1.4.1.2011.5.25.111.4.6.1.1
The index of mping statistics table, and the times of dispatching dependency tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaMtracertStatsHopIndex 1.3.6.1.4.1.2011.5.25.111.4.6.1.2
The index of Mtracert hop
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..255  

nqaMtracertStatsAddressType 1.3.6.1.4.1.2011.5.25.111.4.6.1.3
The destination address type, and the value range can be unknown(0), ipv4(1) and dns(16).
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

nqaMtracertStatsAddress 1.3.6.1.4.1.2011.5.25.111.4.6.1.4
The destination address (TraceRoute is the source address of the last valuable response package).
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaMtracertStatsCompletions 1.3.6.1.4.1.2011.5.25.111.4.6.1.5
The status of test.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noResult(1), success(2), failure(3)  

nqaMtracertStatsCurHopCount 1.3.6.1.4.1.2011.5.25.111.4.6.1.6
It is equal to the hop count index executed by current tests. The default value is 0.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMtracertStatsCurProbeCount 1.3.6.1.4.1.2011.5.25.111.4.6.1.7
The total count of probe packets in a hop count index.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMtracertStatsRTDOverThresholds 1.3.6.1.4.1.2011.5.25.111.4.6.1.8
The times of successful statistics test RTD (Round Trip Delay) over the threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMtracertStatsTimeouts 1.3.6.1.4.1.2011.5.25.111.4.6.1.9
The number of occasions when a NQA operation was not completed before a timeout occurred, i.e. nqaAdminCtrlTimeOut was exceeded.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMtracertStatsBusies 1.3.6.1.4.1.2011.5.25.111.4.6.1.10
The times of failure to apply resource due to the busy system. such as apply memory or create socket failure.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMtracertStatsSequenceErrors 1.3.6.1.4.1.2011.5.25.111.4.6.1.11
The times that sequence error happends.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMtracertStatsDrops 1.3.6.1.4.1.2011.5.25.111.4.6.1.12
The times probes of the test dropped due to sending or connecting failure .
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMtracertStatsProbeResponses 1.3.6.1.4.1.2011.5.25.111.4.6.1.13
The number of received reponse packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMtracertStatsSentProbes 1.3.6.1.4.1.2011.5.25.111.4.6.1.14
The number of sent packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaMtracertStatsLastGoodProbe 1.3.6.1.4.1.2011.5.25.111.4.6.1.15
Date and time when the last response was received for a probe.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

nqaMtracertStatsLastGoodPath 1.3.6.1.4.1.2011.5.25.111.4.6.1.16
The date and time when the last complete path was determined.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

nqaMtracertStatsTestFinished 1.3.6.1.4.1.2011.5.25.111.4.6.1.17
The status of test execution.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noFinish(1), finish(2)  

nqaMtracertStatsCurPathTTL 1.3.6.1.4.1.2011.5.25.111.4.6.1.18
The TTL(time to live) of the current path.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMtracertStatsMaxPathTTL 1.3.6.1.4.1.2011.5.25.111.4.6.1.19
The maximum TTL(time to live) of the path.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMtracertStatsInPkgLossRate 1.3.6.1.4.1.2011.5.25.111.4.6.1.20
The loss rate of the incoming packets.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMtracertStatsSGPkgLossRate 1.3.6.1.4.1.2011.5.25.111.4.6.1.21
The loss rate of the packets from source to multicast group.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMtracertStatsInPkgRate 1.3.6.1.4.1.2011.5.25.111.4.6.1.22
The rate of incoming packets.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMtracertStatsOutPkgRate 1.3.6.1.4.1.2011.5.25.111.4.6.1.23
The rate of outgoing packets.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMtracertStatsTimeDelay 1.3.6.1.4.1.2011.5.25.111.4.6.1.24
The time delay of packets from hop to hop.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathMtuStatsTable 1.3.6.1.4.1.2011.5.25.111.4.7
The statistics collection database. Defines the path MTU Operations Statistics Table for storing the statistics of a path MTU test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaPathMtuStatsEntry

nqaPathMtuStatsEntry 1.3.6.1.4.1.2011.5.25.111.4.7.1
Defines an entry in the nqaPathMtuStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaPathMtuStatsEntry  

nqaPathMtuStatsIndex 1.3.6.1.4.1.2011.5.25.111.4.7.1.1
The index of path MTU statistics table, and the times of dispatching dependency tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaPathMtuStatsAddressType 1.3.6.1.4.1.2011.5.25.111.4.7.1.2
The destination address type, and the value range can be unknown(0), ipv4(1) and dns(16).
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

nqaPathMtuStatsAddress 1.3.6.1.4.1.2011.5.25.111.4.7.1.3
The destination address. It is the source address of the ICMP echo reply packet.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaPathMtuStatsCompletions 1.3.6.1.4.1.2011.5.25.111.4.7.1.4
The status of test.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noResult(0), success(1), failure(2)  

nqaPathMtuStatsSentProbes 1.3.6.1.4.1.2011.5.25.111.4.7.1.5
The number of sent packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathMtuStatsProbeResponses 1.3.6.1.4.1.2011.5.25.111.4.7.1.6
The number of received reponse packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathMtuStatsDiscoveryPathMtuMin 1.3.6.1.4.1.2011.5.25.111.4.7.1.7
The initial length of packet in the path MTU test. It is the minimal length of a ICMP packet.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathMtuStatsDiscoveryPathMtuMax 1.3.6.1.4.1.2011.5.25.111.4.7.1.8
The maximal length of packet in the path MTU test. It is the maximal MTU of local out-interface.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathMtuStatsOptimumFirstStep 1.3.6.1.4.1.2011.5.25.111.4.7.1.9
The optimum first step of the path MTU test. It will take effect if the specified step is lower than it.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathMtuStatsBusies 1.3.6.1.4.1.2011.5.25.111.4.7.1.10
The times of failure to apply resource due to the busy system. such as apply memory or create socket failure.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathMtuStatsTimeouts 1.3.6.1.4.1.2011.5.25.111.4.7.1.11
The number of occasions when a NQA operation was not completed before a timeout occurred, i.e. nqaAdminCtrlTimeOut was exceeded.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathMtuStatsDrops 1.3.6.1.4.1.2011.5.25.111.4.7.1.12
The times probes of the test dropped due to sending or connecting failure.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathMtuStatsPathMtu 1.3.6.1.4.1.2011.5.25.111.4.7.1.13
The value of current path MTU.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathMtuStatsTestFinished 1.3.6.1.4.1.2011.5.25.111.4.7.1.14
The status of test execution.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nofinish(0), finish(1)  

nqaPathJitterStatsTable 1.3.6.1.4.1.2011.5.25.111.4.8
A table which contains the status of latest path jitter operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaPathJitterStatsEntry

nqaPathJitterStatsEntry 1.3.6.1.4.1.2011.5.25.111.4.8.1
A table which contains the status of latest path jitter operation. This entry is created only if the nqaAdminCtrlType is path jitter.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaPathJitterStatsEntry  

nqaPathJitterStatsIndex 1.3.6.1.4.1.2011.5.25.111.4.8.1.1
The index of path jitter statistics table, and the times of dispatching dependency tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaPathJitterStatsHopIndex 1.3.6.1.4.1.2011.5.25.111.4.8.1.2
The index of path jitter hop.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..255  

nqaPathJitterStatsCompletions 1.3.6.1.4.1.2011.5.25.111.4.8.1.3
The status of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noResult(0), success(1), failure(2)  

nqaPathJitterStatsAddressType 1.3.6.1.4.1.2011.5.25.111.4.8.1.4
The destination address type in a hop of path jitter test, and the value range can be unknown(0), ipv4(1) and dns(16).
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

nqaPathJitterStatsAddress 1.3.6.1.4.1.2011.5.25.111.4.8.1.5
The destination address in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaPathJitterStatsRtdOverThresholds 1.3.6.1.4.1.2011.5.25.111.4.8.1.6
The times of successful executions who's RTD over the threshold in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsNumOfRtt 1.3.6.1.4.1.2011.5.25.111.4.8.1.7
The times that statistics RTT successfully in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsRttSum 1.3.6.1.4.1.2011.5.25.111.4.8.1.8
The sum of RTTs in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsRttSum2Low 1.3.6.1.4.1.2011.5.25.111.4.8.1.9
The low order 32 bits of RTT's square sum that successfully measured in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsRttSum2High 1.3.6.1.4.1.2011.5.25.111.4.8.1.10
The high order 32 bits of RTT's square sum that successfully measured in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsRttMin 1.3.6.1.4.1.2011.5.25.111.4.8.1.11
The minimum of RTTs that successfully measured in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsRttMax 1.3.6.1.4.1.2011.5.25.111.4.8.1.12
The maximum of RTTs that successfully measured in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsMinOfPositivesSD 1.3.6.1.4.1.2011.5.25.111.4.8.1.13
The minimum of positive values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsMaxOfPositivesSD 1.3.6.1.4.1.2011.5.25.111.4.8.1.14
The maximum of positive values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsNumOfPositivesSD 1.3.6.1.4.1.2011.5.25.111.4.8.1.15
The number of positive values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsSumOfPositivesSD 1.3.6.1.4.1.2011.5.25.111.4.8.1.16
The sum of positive values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsSum2OfPositivesSDLow 1.3.6.1.4.1.2011.5.25.111.4.8.1.17
The low order 32 bits of square sum of positive values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsSum2OfPositivesSDHigh 1.3.6.1.4.1.2011.5.25.111.4.8.1.18
The high order 32 bits of square sum of positive values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsMinOfNegativesSD 1.3.6.1.4.1.2011.5.25.111.4.8.1.19
The minimum of negative values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsMaxOfNegativesSD 1.3.6.1.4.1.2011.5.25.111.4.8.1.20
The maximum of negative values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsNumOfNegativesSD 1.3.6.1.4.1.2011.5.25.111.4.8.1.21
The number of negative values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsSumOfNegativesSD 1.3.6.1.4.1.2011.5.25.111.4.8.1.22
The sum of negative values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsSum2OfNegativesSDLow 1.3.6.1.4.1.2011.5.25.111.4.8.1.23
The low order 32 bits of square sum of negative values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsSum2OfNegativesSDHigh 1.3.6.1.4.1.2011.5.25.111.4.8.1.24
The high order 32 bits of square sum of negative values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsMinOfPositivesDS 1.3.6.1.4.1.2011.5.25.111.4.8.1.25
The minimum of positive values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsMaxOfPositivesDS 1.3.6.1.4.1.2011.5.25.111.4.8.1.26
The maximum of positive values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsNumOfPositivesDS 1.3.6.1.4.1.2011.5.25.111.4.8.1.27
The number of positive values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsSumOfPositivesDS 1.3.6.1.4.1.2011.5.25.111.4.8.1.28
The sum of positive values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsSum2OfPositivesDSLow 1.3.6.1.4.1.2011.5.25.111.4.8.1.29
The low order 32 bits of square sum of positive values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsSum2OfPositivesDSHigh 1.3.6.1.4.1.2011.5.25.111.4.8.1.30
The high order 32 bits of square sum of positive values of jitter that measured from packetssent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsMinOfNegativesDS 1.3.6.1.4.1.2011.5.25.111.4.8.1.31
The minimum of negative values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsMaxOfNegativesDS 1.3.6.1.4.1.2011.5.25.111.4.8.1.32
The maximum of negative values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsNumOfNegativesDS 1.3.6.1.4.1.2011.5.25.111.4.8.1.33
The number of negative values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsSumOfNegativesDS 1.3.6.1.4.1.2011.5.25.111.4.8.1.34
The sum of negative values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsSum2OfNegativesDSLow 1.3.6.1.4.1.2011.5.25.111.4.8.1.35
The low order 32 bits of square sum of negative values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsSum2OfNegativesDSHigh 1.3.6.1.4.1.2011.5.25.111.4.8.1.36
The high order 32 bits of square sum of negative values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsPacketLossSD 1.3.6.1.4.1.2011.5.25.111.4.8.1.37
The number of dropped packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsPacketLossDS 1.3.6.1.4.1.2011.5.25.111.4.8.1.38
The number of dropped packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsPacketOutOfSequences 1.3.6.1.4.1.2011.5.25.111.4.8.1.39
The number of packets that return out of sequence.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsErrors 1.3.6.1.4.1.2011.5.25.111.4.8.1.40
The number of some other errors type.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsBusies 1.3.6.1.4.1.2011.5.25.111.4.8.1.41
The number of occasions when a path jitter operation could not be initiated because an internal error.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsTimeouts 1.3.6.1.4.1.2011.5.25.111.4.8.1.42
The number of occasions when a NQA operation was not completed before a timeout occurred, i.e. nqaAdminCtrlTimeOut was exceeded.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsProbeResponses 1.3.6.1.4.1.2011.5.25.111.4.8.1.43
The number of responses received for the corresponding test. The value of this object MUST be reported as 0 when no probe responses have been received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsSentProbes 1.3.6.1.4.1.2011.5.25.111.4.8.1.44
The value of this object reflects the number of packets sent for the corresponding test. The value of this object MUST be reported as 0 when no probes have been sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsDrops 1.3.6.1.4.1.2011.5.25.111.4.8.1.45
The times probes of the test dropped due to sending failure.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsTestFinished 1.3.6.1.4.1.2011.5.25.111.4.8.1.46
The status of test execution.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noFinish(0), finish(1)  

nqaPathJitterStatsMaxDelaySD 1.3.6.1.4.1.2011.5.25.111.4.8.1.47
The maximum of all OWD (One Way Delay) that measured from packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsMaxDelayDS 1.3.6.1.4.1.2011.5.25.111.4.8.1.48
The maximum of all OWD (One Way Delay) that measured from packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsRttAvg 1.3.6.1.4.1.2011.5.25.111.4.8.1.49
The average of RTTs that were successfully measured in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsPacketLossRatio 1.3.6.1.4.1.2011.5.25.111.4.8.1.50
The ratio of the packets lost to all packets sent in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsAvgJitter 1.3.6.1.4.1.2011.5.25.111.4.8.1.51
The average of jitter values that were successfully measured in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsAvgJitterSD 1.3.6.1.4.1.2011.5.25.111.4.8.1.52
The average value of jitters that measured from packets sent from sourse to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsAvgJitterDS 1.3.6.1.4.1.2011.5.25.111.4.8.1.53
The average value of jitters that measured from packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPathJitterStatsJitterOut 1.3.6.1.4.1.2011.5.25.111.4.8.1.54
jitter (RFC1889) at responder.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaPathJitterStatsJitterIn 1.3.6.1.4.1.2011.5.25.111.4.8.1.55
Jitter (RFC1889) at sender.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaPathJitterStatsOwdOverThresholdsSD 1.3.6.1.4.1.2011.5.25.111.4.8.1.56
The number of tests that violate OWD (One Way Delay) threshold from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsPktLossUnknown 1.3.6.1.4.1.2011.5.25.111.4.8.1.57
The number of lost packets for which we can't determine the direction in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsNumOfOwd 1.3.6.1.4.1.2011.5.25.111.4.8.1.58
The number of OWDs that were successfully measured in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsOwdSumSD 1.3.6.1.4.1.2011.5.25.111.4.8.1.59
The sum of OWDs that were successfully measured from packets sent from source to destination in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsOwdSumDS 1.3.6.1.4.1.2011.5.25.111.4.8.1.60
The sum of OWDs that were successfully measured from packets sent from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPathJitterStatsOwdOverThresholdsDS 1.3.6.1.4.1.2011.5.25.111.4.8.1.61
The number of tests that violate OWD (One Way Delay) threshold from destination to source in a hop of path jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaPppoeStatsTable 1.3.6.1.4.1.2011.5.25.111.4.9
A table which contains the rolling accumulated history of the PPPoE operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaPppoeStatsEntry

nqaPppoeStatsEntry 1.3.6.1.4.1.2011.5.25.111.4.9.1
A table which contains the rolling accumulated history of the PPPoE operation. This entry is created only if the nqaAdminCtrlType is pppoe.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaPppoeStatsEntry  

nqaPppoeStatsIndex 1.3.6.1.4.1.2011.5.25.111.4.9.1.1
The index of PPPoE statistics table, and the executing times of dispatching dependency tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

nqaPppoeRedialIndex 1.3.6.1.4.1.2011.5.25.111.4.9.1.2
The index of PPPoE statistics table, and the redialing times of dispatching dependency tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

nqaPppoeStatsCompletions 1.3.6.1.4.1.2011.5.25.111.4.9.1.3
The status of PPPoE operation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dialupSuccess(1), dialupFail(2), stop(3), exceptionStop(4)  

nqaPppoeStatsCurrentPhase 1.3.6.1.4.1.2011.5.25.111.4.9.1.4
The current phase of PPPoE operation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER discovery(1), lcp(2), authorization(3), ncp(4), online(5), stop(6)  

nqaPppoeStatsErrorMessage 1.3.6.1.4.1.2011.5.25.111.4.9.1.5
The error message result of PPPoE operation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), timeout(2), paramNegotiateFail(3), userAuthenticationFail(4), peerDownRequest(5), noError(255)  

nqaPppoeDiscoveryTimeout 1.3.6.1.4.1.2011.5.25.111.4.9.1.6
The time for discovery of PPPoE operation.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPppoeLcpTimeout 1.3.6.1.4.1.2011.5.25.111.4.9.1.7
The time for lcp negotiate of PPPoE operation.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPppoeAuthorizationTimeout 1.3.6.1.4.1.2011.5.25.111.4.9.1.8
The time for authentication of PPPoE operation.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPppoeNcpTimeout 1.3.6.1.4.1.2011.5.25.111.4.9.1.9
The time for ncp negotiate of PPPoE operation.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPppoeConnectionTime 1.3.6.1.4.1.2011.5.25.111.4.9.1.10
The time for connection of PPPoE operation.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPppoeClientSessionId 1.3.6.1.4.1.2011.5.25.111.4.9.1.11
The client sessionID of PPPoE operation.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaPppoeClientIpAddress 1.3.6.1.4.1.2011.5.25.111.4.9.1.12
The client ip address of PPPoE operation.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaPppoeGatewayIpAddress 1.3.6.1.4.1.2011.5.25.111.4.9.1.13
The gateway ip address of PPPoE operation.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaHistory 1.3.6.1.4.1.2011.5.25.111.5
OBJECT IDENTIFIER    

nqaHistoryTable 1.3.6.1.4.1.2011.5.25.111.5.1
Defines the Remote Operations test History Table for storing the results of a test operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaHistoryEntry

nqaHistoryEntry 1.3.6.1.4.1.2011.5.25.111.5.1.1
Defines a table for storing the results of a test operation. Entries in this table are limited by the value of the corresponding nqaAdminParaHistoryRowMax.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaHistoryEntry  

nqaHistoryIndex 1.3.6.1.4.1.2011.5.25.111.5.1.1.1
The history table index and times for dispatching dependency tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaHistoryHopIndex 1.3.6.1.4.1.2011.5.25.111.5.1.1.2
The hop index. If the test type is Traceroute or LSP Traceroute, the entry only defines one hop. For other types, the default value is 1.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..255  

nqaHistoryProbeIndex 1.3.6.1.4.1.2011.5.25.111.5.1.1.3
The probe index of tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaHistoryTimeStamp 1.3.6.1.4.1.2011.5.25.111.5.1.1.4
The start time stamp of a probe.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

nqaHistoryAddressType 1.3.6.1.4.1.2011.5.25.111.5.1.1.5
The address type of history records.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

nqaHistoryAddress 1.3.6.1.4.1.2011.5.25.111.5.1.1.6
The destination address of tests. For Traceroute, it is the destination address of each hop.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaHistoryCompletionTime 1.3.6.1.4.1.2011.5.25.111.5.1.1.7
The amount of time measured in milliseconds from when a probe was sent to when its response was received or when it timed out. The value of this object is reported as 0 when it is not possible to transmit a probe.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaHistoryFinishState 1.3.6.1.4.1.2011.5.25.111.5.1.1.8
The result of a test operation made by a remote host for a particular probe.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER success(1), timeout(2), drop(3), busy(4), overThreshold(5), disconnected(6), noConnected(7)  

nqaHistoryLastRC 1.3.6.1.4.1.2011.5.25.111.5.1.1.9
The last implementation method specific reply code received. If the ICMP Echo capability is being used then a successful probe ends when an ICMP response is received that contains the code ICMP_ECHOREPLY(0). The ICMP responses are defined normally in the ip_icmp include file.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaMpingHistoryTable 1.3.6.1.4.1.2011.5.25.111.5.2
Defines the Remote Operations Mping test History Table for storing the results of a test operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaMpingHistoryEntry

nqaMpingHistoryEntry 1.3.6.1.4.1.2011.5.25.111.5.2.1
Defines a table for storing the results of a test operation. Entries in this table are limited by the value of the corresponding nqaAdminParaHistoryRowMax.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaMpingHistoryEntry  

nqaMpingHistoryIndex 1.3.6.1.4.1.2011.5.25.111.5.2.1.1
The Mping history table index and times for dispatching dependency tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaMpingHistoryReceiverIndex 1.3.6.1.4.1.2011.5.25.111.5.2.1.2
The index of receiver ,that received mping request packets and response reply packets .
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaMpingHistoryResponseIndex 1.3.6.1.4.1.2011.5.25.111.5.2.1.3
The index of response packets send by receiver
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaMpingHistoryAddressType 1.3.6.1.4.1.2011.5.25.111.5.2.1.4
The address type of history records.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

nqaMpingHistoryAddress 1.3.6.1.4.1.2011.5.25.111.5.2.1.5
The destination address of tests.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaMpingHistoryReceiverAddress 1.3.6.1.4.1.2011.5.25.111.5.2.1.6
The source address of response package of tests.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaMpingHistoryTimeStamp 1.3.6.1.4.1.2011.5.25.111.5.2.1.7
The start time stamp of a probe.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

nqaMpingHistoryCompletionTime 1.3.6.1.4.1.2011.5.25.111.5.2.1.8
The completion time of a probe in milliseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaMpingHistoryFinishState 1.3.6.1.4.1.2011.5.25.111.5.2.1.9
The result of a test operation made by a remote host for a particular probe.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER success(1), timeout(2), drop(3), busy(4), overThreshold(5), disconnected(6), noConnected(7)  

nqaMpingHistoryLastRC 1.3.6.1.4.1.2011.5.25.111.5.2.1.10
The last reply code received.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaMpingHistoryFibHit 1.3.6.1.4.1.2011.5.25.111.5.2.1.11
Whether the fib is hit on the device which received the packet.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

nqaMtracertHistoryTable 1.3.6.1.4.1.2011.5.25.111.5.3
Defines the Remote MtracertOperations test History Table for storing the results of a test operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaMtracertHistoryEntry

nqaMtracertHistoryEntry 1.3.6.1.4.1.2011.5.25.111.5.3.1
Defines a table for storing the results of a test operation. Entries in this table are limited by the value of the corresponding nqaAdminParaHistoryRowMax.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaMtracertHistoryEntry  

nqaMtracertHistoryIndex 1.3.6.1.4.1.2011.5.25.111.5.3.1.1
The Mtracert history table index and times for dispatching dependency tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaMtracertHistoryHopIndex 1.3.6.1.4.1.2011.5.25.111.5.3.1.2
The index of Mtracert hop.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..255  

nqaMtracertHistoryAddressType 1.3.6.1.4.1.2011.5.25.111.5.3.1.3
The address type of history records.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

nqaMtracertHistoryAddress 1.3.6.1.4.1.2011.5.25.111.5.3.1.4
The destination address of tests. For Traceroute, it is the destination address of each hop.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaMtracertHistoryTimeStamp 1.3.6.1.4.1.2011.5.25.111.5.3.1.5
The start time stamp of a probe.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

nqaMtracertHistoryCompletionTime 1.3.6.1.4.1.2011.5.25.111.5.3.1.6
The amount of time measured in milliseconds from when a probe was sent to when its response was received or when it timed out. The value of this object is reported as 0 when it is not possible to transmit a probe.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaMtracertHistoryLastRC 1.3.6.1.4.1.2011.5.25.111.5.3.1.7
The last implementation method specific reply code received. If the ICMP Echo capability is being used then a successful probe ends when an ICMP response is received that contains the code ICMP_ECHOREPLY(0). The ICMP responses are defined normally in the ip_icmp include file.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaMtracertHistoryCurQueryMode 1.3.6.1.4.1.2011.5.25.111.5.3.1.8
The current query mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER maxHops(1), hopByHop(2)  

nqaMtracertHistoryQueryArrivalTime 1.3.6.1.4.1.2011.5.25.111.5.3.1.9
The Query Arrival Time is a 32-bit NTP timestamp specifying the arrival time of the traceroute request packet at this router.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

nqaMtracertHistoryIncomingIfAddress 1.3.6.1.4.1.2011.5.25.111.5.3.1.10
This field specifies the address of the interface on which packets from this source and group are expected to arrive, or 0 if unknown.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaMtracertHistoryOutgoingIfAddress 1.3.6.1.4.1.2011.5.25.111.5.3.1.11
This field specifies the address of the interface on which packets from this source and group flow to the specified destination, or 0 if unknown.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaMtracertHistoryPreHopRouterAddress 1.3.6.1.4.1.2011.5.25.111.5.3.1.12
This field specifies the router from which this router expects packets from this source.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaMtracertHistoryInputPacketCount 1.3.6.1.4.1.2011.5.25.111.5.3.1.13
This field contains the number of multicast packets received for all groups and sources on the incoming interface, or 0xffffffff if no count can be reported. This counter should have the same value as ifInMulticastPkts from the IF-MIB for this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMtracertHistoryOutputPacketCount 1.3.6.1.4.1.2011.5.25.111.5.3.1.14
This field contains the number of multicast packets that have been transmitted or queued for transmission for all groups and sources on the outgoing interface, or 0xffffffff if no count can be reported. This counter should have the same value as ifOutMulti-castPkts from the IF-MIB for this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMtracertHistoryTotalSGPacketCount 1.3.6.1.4.1.2011.5.25.111.5.3.1.15
This field counts the number of packets from the specified source forwarded by this router to the specified group, or 0xffffffff if no count can be reported. This counter should have the same value as ipMRoutePkts from the IPMROUTE-STD-MIB for this forwarding entry.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMtracertHistoryRtgProtocol 1.3.6.1.4.1.2011.5.25.111.5.3.1.16
This field describes the routing protocol in use between this router and the previous-hop router.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dvmrp(1), mospf(2), pim(3), cbt(4), pimUsingSpecRteTab(5), pimUsingStaticRte(6), dvmrpUsingStaticRte(7), pimUsingMBGPRte(8), cbtUsingSpecRteTab(9), cbtUsingStaticRte(10), pimUsingState(11), unknownProtocol(255)  

nqaMtracertHistoryFwdTTL 1.3.6.1.4.1.2011.5.25.111.5.3.1.17
This field contains the TTL that a packet is required to have before it will be forwarded over the outgoing interface.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaMtracertHistoryFwdCode 1.3.6.1.4.1.2011.5.25.111.5.3.1.18
This field contains a forwarding information/error code. noError(1): No error wrongIf(2): Traceroute request arrived on an interface to which this router would not forward for this source,group,destination. pruneSent(3): This router has sent a prune upstream which applies to the source and group in the tracer- oute request. pruneRCVD(4): This router has stopped forwarding for this source and group in response to a request from the next hop router. scoped(5): The group is subject to administrative scoping at this hop. noRoute(6): This router has no route for the source or group and no way to determine a potential route. wrongLastHop(7): This router is not the proper last-hop router. notForwarding(8):This router is not forwarding this source,group out the outgoing interface for an unspecified reason. reachedRP(9): Reached Rendez-vous Point or Core rpfIf(10): Traceroute request arrived on the expected RPF interface for this source,group. noMulticast(11): Traceroute request arrived on an interface which is not enabled for multicast. infoHidden(12): One or more hops have been hidden from this trace. noSpace(13): There was not enough room to insert another response data block in the packet. oldRouter(14): The previous hop router does not understand traceroute requests. adminProhib(15): Traceroute is administratively prohibited.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noError(1), wrongIf(2), pruneSent(3), pruneRCVD(4), scoped(5), noRoute(6), wrongLastHop(7), notForwarding(8), reachedRP(9), noMulticast(11), infoHidden(12), noSpace(130), oldRouter(131), adminProhib(132), unknownError(255)  

nqaMtracertHistroyFinishState 1.3.6.1.4.1.2011.5.25.111.5.3.1.19
The finish state of a probe.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER success(1), timeout(2), busy(3), drop(4), overThreshold(5), disconnected(6), noConnected(7)  

nqaVplsMacTracertHistoryTable 1.3.6.1.4.1.2011.5.25.111.5.4
Defines the VPLS mac trace Operations test History Table for storing the results of a test operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaVplsMacTracertHistoryEntry

nqaVplsMacTracertHistoryEntry 1.3.6.1.4.1.2011.5.25.111.5.4.1
Defines a table for storing the results of a test operation. Entries in this table are limited by the value of the corresponding nqaAdminParaHistoryRowMax.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaVplsMacTracertHistoryEntry  

nqaVplsMacTracertHistoryIndex 1.3.6.1.4.1.2011.5.25.111.5.4.1.1
The VPLS mac trace history table index and times for dispatching dependency tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaVplsMacTracertHistoryHopIndex 1.3.6.1.4.1.2011.5.25.111.5.4.1.2
The index of VPLS mac trace hop.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..255  

nqaVplsMacTracertHistoryResponseIndex 1.3.6.1.4.1.2011.5.25.111.5.4.1.3
The index of VPLS mac trace reply packet per hop.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..255  

nqaVplsMacTracertHistoryTimeStamp 1.3.6.1.4.1.2011.5.25.111.5.4.1.4
The start time stamp of a probe.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

nqaVplsMacTracertHistoryAddressType 1.3.6.1.4.1.2011.5.25.111.5.4.1.5
The address type of history records.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

nqaVplsMacTracertHistoryAddress 1.3.6.1.4.1.2011.5.25.111.5.4.1.6
The destination address of tests. For Traceroute, it is the destination address of each hop.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaVplsMacTracertHistoryCompletionTime 1.3.6.1.4.1.2011.5.25.111.5.4.1.7
The completion time of a probe in milliseconds. The amount of time measured in milliseconds from when a probe was sent to when its response was received or when it timed out. The value of this object is reported as 0 when it is not possible to transmit a probe.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaVplsMacTracertHistoryFinishState 1.3.6.1.4.1.2011.5.25.111.5.4.1.8
The finish state of a probe.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER success(1), timeout(2), drop(3), busy(4), overThreshold(5), disconnected(6), noConnected(7)  

nqaVplsMacTracertHistoryHitFlag 1.3.6.1.4.1.2011.5.25.111.5.4.1.9
Hit Flag.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

nqaVplsMacTracertHistoryDSCount 1.3.6.1.4.1.2011.5.25.111.5.4.1.10
The count of Downstreams.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7FFFFFFF  

nqaVplsMacTracertHistorySuccessPathNode 1.3.6.1.4.1.2011.5.25.111.5.4.1.11
This object indicates whether it is a node along the path that passes the Trace test. By default, the value is false, indicating that the object is not a node along the path that passes the Trace test.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

nqaVplsMacTracertHistoryDSTable 1.3.6.1.4.1.2011.5.25.111.5.5
Defines the VPLS mac trace Operations test History Downstreanm Table for storing the results of a test operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaVplsMacTracertHistoryDSEntry

nqaVplsMacTracertHistoryDSEntry 1.3.6.1.4.1.2011.5.25.111.5.5.1
Defines a table for storing the results of a test operation. Entries in this table are limited by the value of the corresponding nqaAdminParaHistoryRowMax.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaVplsMacTracertHistoryDSEntry  

nqaVplsMacTracertHistoryDSIndex 1.3.6.1.4.1.2011.5.25.111.5.5.1.1
The VPLS mac trace history DS table index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaVplsMacTracertHistoryDSAddress 1.3.6.1.4.1.2011.5.25.111.5.5.1.2
DS address.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaVplsMTraceHistoryTable 1.3.6.1.4.1.2011.5.25.111.5.6
Defines the remote vpls multicast trace operations test history table for storing the results of a test operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaVplsMTraceHistoryEntry

nqaVplsMTraceHistoryEntry 1.3.6.1.4.1.2011.5.25.111.5.6.1
Defines a table for storing the results of a test operation. Entries in this table are limited by the value of the corresponding nqaAdminParaHistoryRowMax.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaVplsMTraceHistoryEntry  

nqaVplsMTraceHistoryIndex 1.3.6.1.4.1.2011.5.25.111.5.6.1.1
The vpls multicast trace history table index and times for dispatching dependency tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaVplsMTraceHistoryHopIndex 1.3.6.1.4.1.2011.5.25.111.5.6.1.2
The index of vpls multicast trace hop.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..255  

nqaVplsMTraceHistoryResponseIndex 1.3.6.1.4.1.2011.5.25.111.5.6.1.3
The index of vpls multicast trace responser.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaVplsMTraceHistoryResponserAddressType 1.3.6.1.4.1.2011.5.25.111.5.6.1.4
The type of history record's Responser address.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

nqaVplsMTraceHistoryResponserAddress 1.3.6.1.4.1.2011.5.25.111.5.6.1.5
The Responser address of tests.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaVplsMTraceHistoryUpStreamAddressType 1.3.6.1.4.1.2011.5.25.111.5.6.1.6
The type of history records' last hop address.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

nqaVplsMTraceHistoryUpStreamAddress 1.3.6.1.4.1.2011.5.25.111.5.6.1.7
The last hop address of tests.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

nqaVplsMTraceHistoryReceivedTtl 1.3.6.1.4.1.2011.5.25.111.5.6.1.8
The value of ttl in the received packet.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..255  

nqaVplsMTraceHistoryIGMPVersion 1.3.6.1.4.1.2011.5.25.111.5.6.1.9
The IGMP protocol version.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER igmpv1(1), igmpv2(2), igmpv3(3)  

nqaVplsMTraceHistoryIGMPSnpgEnable 1.3.6.1.4.1.2011.5.25.111.5.6.1.10
The IGMP snooping enable state.
Status: current Access: read-only
OBJECT-TYPE    
  EnableValue  

nqaVplsMTraceHistoryIGMPProxyEnable 1.3.6.1.4.1.2011.5.25.111.5.6.1.11
The IGMP proxy enable switch.
Status: current Access: read-only
OBJECT-TYPE    
  EnableValue  

nqaVplsMTraceHistoryIGMPRouterPortLearningEnable 1.3.6.1.4.1.2011.5.25.111.5.6.1.12
The IGMP router port learning enable switch.
Status: current Access: read-only
OBJECT-TYPE    
  EnableValue  

nqaVplsMTraceHistoryRequireRouterAlertEnable 1.3.6.1.4.1.2011.5.25.111.5.6.1.13
The route alert requirement enable switch.
Status: current Access: read-only
OBJECT-TYPE    
  EnableValue  

nqaVplsMTraceHistoryForwardMode 1.3.6.1.4.1.2011.5.25.111.5.6.1.14
The forward mode value.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER mac(1), ip(2)  

nqaVplsMTraceHistoryHitFlag 1.3.6.1.4.1.2011.5.25.111.5.6.1.15
Whether the fib is hit on the device which received the packet.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

nqaVplsMTraceHistoryPWExist 1.3.6.1.4.1.2011.5.25.111.5.6.1.16
Whether the forward PW is exist.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

nqaVplsMTraceHistoryGroupPolicy 1.3.6.1.4.1.2011.5.25.111.5.6.1.17
The ACL judge result.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

nqaVplsMTraceHistoryCACExist 1.3.6.1.4.1.2011.5.25.111.5.6.1.18
Whether the connection admission control comfiguration of current VSI is exist.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

nqaVplsMTraceHistoryRcvQueryCount 1.3.6.1.4.1.2011.5.25.111.5.6.1.19
The received query packet number for current IGMP version of current VSI.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaVplsMTraceHistoryRcvReportCount 1.3.6.1.4.1.2011.5.25.111.5.6.1.20
The received report packet number for current IGMP version of current VSI.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaVplsMTraceHistoryRcvLeaveCount 1.3.6.1.4.1.2011.5.25.111.5.6.1.21
The received leave packet number for current IGMP version of current VSI.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaVplsMTraceHistoryTimeStamp 1.3.6.1.4.1.2011.5.25.111.5.6.1.22
The start time stamp of a probe.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

nqaVplsMTraceHistoryCompletionTime 1.3.6.1.4.1.2011.5.25.111.5.6.1.23
The amount of time measured in milliseconds from when a probe was sent to when its response was received or when it timed out. The value of this object is reported as 0 when it is not possible to transmit a probe.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaVplsMTraceHistoryLastRC 1.3.6.1.4.1.2011.5.25.111.5.6.1.24
The last implementation method specific reply code received.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaVplsMTraceHistoryLastRSC 1.3.6.1.4.1.2011.5.25.111.5.6.1.25
The last implementation method specific reply sub code received.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaVplsMTraceHistoryFinishState 1.3.6.1.4.1.2011.5.25.111.5.6.1.26
The finish state of a probe.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER success(1), timeout(2), drop(3), busy(4), overThreshold(5), disconnected(6), noConnected(7)  

nqaVplsMTraceHistorySuccessPathNode 1.3.6.1.4.1.2011.5.25.111.5.6.1.27
Whether the response router is on the path of a probe. The default value is notonPath(2).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER onPath(1), notonPath(2)  

nqaMacTraceHistoryTable 1.3.6.1.4.1.2011.5.25.111.5.7
This object defines a list of historical MAC trace test instances for storing the running results of test instances.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaMacTraceHistoryEntry

nqaMacTraceHistoryEntry 1.3.6.1.4.1.2011.5.25.111.5.7.1
This object defines a table for storing the running results of test instances. The number of entries in this table is limited by the value of nqaAdminParaHistoryRowMax.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaMacTraceHistoryEntry  

nqaMacTraceHistoryIndex 1.3.6.1.4.1.2011.5.25.111.5.7.1.1
The object indicates the index of the MAC tract history table and the number of times for dispatching dependency tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

nqaMacTraceHistoryReceiveOrder 1.3.6.1.4.1.2011.5.25.111.5.7.1.2
This object indicates the sequence in which LTRs are received.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

nqaMacTraceHistoryTTL 1.3.6.1.4.1.2011.5.25.111.5.7.1.3
This object indicates the TTL of the LTR.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..255  

nqaMacTraceHistorySeqNumber 1.3.6.1.4.1.2011.5.25.111.5.7.1.4
This object indicates the sequence number of the LTR.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

nqaMacTraceHistoryCompletionTime 1.3.6.1.4.1.2011.5.25.111.5.7.1.5
This object indicates the RTT (ms) of the response packet.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nqaMacTraceHistoryForwarded 1.3.6.1.4.1.2011.5.25.111.5.7.1.6
This object indicates whether the device that sends LTRs continues to forward LTMs.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

nqaMacTraceHistoryTerminalMep 1.3.6.1.4.1.2011.5.25.111.5.7.1.7
This object indicates whether the LTR is sent by an MEP.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

nqaMacTraceHistoryRelayAction 1.3.6.1.4.1.2011.5.25.111.5.7.1.8
This object indicates the value of the Relay Action field in the LTR.
Status: current Access: read-only
OBJECT-TYPE    
  HWDot1agCfmRelayActionFieldValue  

nqaMacTraceHistoryIngressAction 1.3.6.1.4.1.2011.5.25.111.5.7.1.9
This object indicates the value of the Ingress Action field in the LTR.
Status: current Access: read-only
OBJECT-TYPE    
  HWDot1agCfmIngressActionFieldValue  

nqaMacTraceHistoryIngressMac 1.3.6.1.4.1.2011.5.25.111.5.7.1.10
This object indicates the physical MAC address carried in the ingress MAC address field in the LTR.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

nqaMacTraceHistoryIngressIfName 1.3.6.1.4.1.2011.5.25.111.5.7.1.11
This object indicates the name of the inbound interface of the LTR.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaMacTraceHistoryEgressAction 1.3.6.1.4.1.2011.5.25.111.5.7.1.12
This object indicates the value of the Egress Action field in the LTR.
Status: current Access: read-only
OBJECT-TYPE    
  HWDot1agCfmEgressActionFieldValue  

nqaMacTraceHistoryEgressMac 1.3.6.1.4.1.2011.5.25.111.5.7.1.13
This object indicates the MAC address in the Egress MAC address field of the LTR.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

nqaMacTraceHistoryEgressIfName 1.3.6.1.4.1.2011.5.25.111.5.7.1.14
This object indicates the name of the interface that forwards the LTR.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaNotifications 1.3.6.1.4.1.2011.5.25.111.6
OBJECT IDENTIFIER    

nqaResultsProbeFailed 1.3.6.1.4.1.2011.5.25.111.6.1
Generated when a probe failure is detected when the corresponding nqaAdminParaTrapGeneration object is set to probeFailure(0) subject to the value of nqaAdminParaTrapProbeFailureFilter. The object nqaAdminParaTrapProbeFailureFilter can be used to specify the number of successive probe failures that are required before this notification can be generated.(except for HTTP or Jitter or FTP)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaResultsTestFailed 1.3.6.1.4.1.2011.5.25.111.6.2
Generated when a nqa test is determined to have failed when the corresponding nqaAdminParaTrapGeneration object is set to testFailure(1). In this instance nqaAdminParaTrapTestFailureFilter should specify the number of probes in a test required to have failed in order to consider the test as failed. (Except for HTTP or Jitter or FTP)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaResultsTestCompleted 1.3.6.1.4.1.2011.5.25.111.6.3
Generated at the completion of a nqa test when the corresponding nqaAdminParaTrapGeneration object is set to testCompletion(2).(except for HTTP or Jitter or FTP)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaResultsThresholdNotification 1.3.6.1.4.1.2011.5.25.111.6.4
If the time of executing tests exceeds the nqaAdminCtrlThreshold1, the system sends trap information.(except for HTTP or Jitter or FTP)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaHTTPStatsProbeFailed 1.3.6.1.4.1.2011.5.25.111.6.5
Generated when a probe failure is detected when the corresponding nqaAdminParaTrapGeneration object is set to probeFailure(0) subject to the value of nqaAdminParaTrapProbeFailureFilter. The object nqaAdminParaTrapProbeFailureFilter can be used to specify the number of successive probe failures that are required before this notification can be generated.(Only for HTTP)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaHTTPStatsTestFailed 1.3.6.1.4.1.2011.5.25.111.6.6
Generated when a HTTP test is determined to have failed when the corresponding nqaAdminParaTrapGeneration object is set to testFailure(1). In this instance nqaAdminParaTrapTestFailureFilter should specify the number of probes in a test required to have failed in order to consider the test as failed.(Only for HTTP)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaHTTPStatsTestCompleted 1.3.6.1.4.1.2011.5.25.111.6.7
Generated at the completion of a HTTP test when the corresponding nqaAdminParaTrapGeneration object is set to testCompletion(2).
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaHTTPStatsThresholdNotification 1.3.6.1.4.1.2011.5.25.111.6.8
If the time of executing tests exceeds the nqaAdminCtrlThreshold1 or nqaAdminCtrlThreshold2 or nqaAdminCtrlThreshold3, the system sends trap information.(Only for HTTP)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaJitterStatsProbeFailed 1.3.6.1.4.1.2011.5.25.111.6.9
Generated when a probe failure is detected when the corresponding nqaAdminParaTrapGeneration object is set to probeFailure(0) subject to the value of nqaAdminParaTrapProbeFailureFilter. The object nqaAdminParaTrapProbeFailureFilter can be used to specify the number of successive probe failures that are required before this notification can be generated.(Only for Jitter)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaJitterStatsTestFailed 1.3.6.1.4.1.2011.5.25.111.6.10
Generated when a Jitter test is determined to have failed when the corresponding nqaAdminParaTrapGeneration object is set to testFailure(1). In this instance nqaAdminParaTrapTestFailureFilter should specify the number of probes in a test required to have failed in order to consider the test as failed.(Only for Jitter)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaJitterStatsTestCompleted 1.3.6.1.4.1.2011.5.25.111.6.11
Generated at the completion of a Jitter test when the corresponding nqaAdminParaTrapGeneration object is set to testCompletion(2). (Only for Jitter)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaFTPStatsProbeFailed 1.3.6.1.4.1.2011.5.25.111.6.12
Generated when a probe failure is detected when the corresponding nqaAdminParaTrapGeneration object is set to probeFailure(0) subject to the value of nqaAdminParaTrapProbeFailureFilter. The object nqaAdminParaTrapProbeFailureFilter can be used to specify the number of successive probe failures that are required before this notification can be generated.(Only for FTP)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaFTPStatsTestFailed 1.3.6.1.4.1.2011.5.25.111.6.13
Generated when a FTP test is determined to have failed when the corresponding nqaAdminParaTrapGeneration object is set to testFailure(1). In this instance nqaAdminParaTrapTestFailureFilter should specify the number of probes in a test required to have failed in order to consider the test as failed.(Only for FTP)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaFTPStatsTestCompleted 1.3.6.1.4.1.2011.5.25.111.6.14
Generated at the completion of a FTP test when the corresponding nqaAdminParaTrapGeneration object is set to testCompletion(2). (Only for FTP)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaFTPStatsThresholdNotification 1.3.6.1.4.1.2011.5.25.111.6.15
If the time of executing tests exceeds the nqaAdminCtrlThreshold1 or nqaAdminCtrlThreshold2, the system sends trap information.(Only for FTP)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaJitterStatsRTDThresholdNotification 1.3.6.1.4.1.2011.5.25.111.6.16
If the time of executing tests exceeds the nqaAdminCtrlThreshold1, the system sends trap information. (Only for jitter)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaJitterStatsOWDThresholdNotificationSD 1.3.6.1.4.1.2011.5.25.111.6.17
If the time of executing tests exceeds the nqaAdminCtrlThreshold2 the system sends trap information. (Only for jitter)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaJitterStatsOWDThresholdNotificationDS 1.3.6.1.4.1.2011.5.25.111.6.18
If the time of executing tests exceeds the nqaAdminCtrlThreshold3 the system sends trap information. (Only for jitter)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaNegotiateFailed 1.3.6.1.4.1.2011.5.25.111.6.19
If negotiation between client and server failed,the system sends trap information.
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaRisingAlarmNotification 1.3.6.1.4.1.2011.5.25.111.6.20
Sending trap messages when the value of the monitored object exceeds nqaAlarmUpperThreshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaFallingAlarmNotification 1.3.6.1.4.1.2011.5.25.111.6.21
Sending trap messages when the value of the monitored object is under nqaAlarmLowerThreshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaFtpSaveRecordNotification 1.3.6.1.4.1.2011.5.25.111.6.22
Sending trap messages when saving a test result to the FTP server is completed.
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaPppoeStatsTestFailed 1.3.6.1.4.1.2011.5.25.111.6.23
Generated when a PPPoE test is determined to have failed when the corresponding nqaAdminParaTrapGeneration object is set to testFailure(1). (Only for PPPoE))
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaPppoeStatsTestCompleted 1.3.6.1.4.1.2011.5.25.111.6.24
Generated at the completion of a PPPoE test when the corresponding nqaAdminParaTrapGeneration object is set to testCompletion(2). (Only for PPPoE)
Status: current Access: read-only
NOTIFICATION-TYPE    

nqaConformance 1.3.6.1.4.1.2011.5.25.111.7
OBJECT IDENTIFIER    

nqaGroups 1.3.6.1.4.1.2011.5.25.111.7.1
OBJECT IDENTIFIER    

nqaBaseGroup 1.3.6.1.4.1.2011.5.25.111.7.1.1
Description.
Status: current Access: read-only
OBJECT-GROUP    

nqaAdminGroup 1.3.6.1.4.1.2011.5.25.111.7.1.2
Description.
Status: current Access: read-only
OBJECT-GROUP    

nqaServerGroup 1.3.6.1.4.1.2011.5.25.111.7.1.3
Description.
Status: current Access: read-only
OBJECT-GROUP    

nqaStatsGroup 1.3.6.1.4.1.2011.5.25.111.7.1.4
Description.
Status: current Access: read-only
OBJECT-GROUP    

nqaHistoryGroup 1.3.6.1.4.1.2011.5.25.111.7.1.5
Description.
Status: current Access: read-only
OBJECT-GROUP    

nqaNotificationsGroup 1.3.6.1.4.1.2011.5.25.111.7.1.6
The notification which are required to be supported by implementations of this MIB.
Status: current Access: read-only
NOTIFICATION-GROUP    

nqaCollectStatsGroup 1.3.6.1.4.1.2011.5.25.111.7.1.7
Description.
Status: current Access: read-only
OBJECT-GROUP    

nqaAlarmGroup 1.3.6.1.4.1.2011.5.25.111.7.1.8
Description.
Status: current Access: read-only
OBJECT-GROUP    

nqaFtpSaveRecordGroup 1.3.6.1.4.1.2011.5.25.111.7.1.9
Description.
Status: current Access: read-only
OBJECT-GROUP    

nqaCompliances 1.3.6.1.4.1.2011.5.25.111.7.2
OBJECT IDENTIFIER    

nqaCompliance 1.3.6.1.4.1.2011.5.25.111.7.2.1
Description.
Status: current Access: read-only
MODULE-COMPLIANCE    

nqaCollectStats 1.3.6.1.4.1.2011.5.25.111.8
OBJECT IDENTIFIER    

nqaJitterCollectStatsTable 1.3.6.1.4.1.2011.5.25.111.8.1
A table which contains the rolling accumulated history of the Jitter operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaJitterCollectStatsEntry

nqaJitterCollectStatsEntry 1.3.6.1.4.1.2011.5.25.111.8.1.1
A table which contains the rolling accumulated history of the Jitter operation. This entry is created only if the nqaAdminCtrlType is jitterAppl.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaJitterCollectStatsEntry  

nqaJitterCollectStatsIndex 1.3.6.1.4.1.2011.5.25.111.8.1.1.1
The third index of jitter collection statistics table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7FFFFFFF  

nqaJitterCollectStatsCompletions 1.3.6.1.4.1.2011.5.25.111.8.1.1.2
The number of the tests that have completed successfully.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsRTDOverThresholds 1.3.6.1.4.1.2011.5.25.111.8.1.1.3
The number of tests that violate RTD (Round Trip Delay) threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsOWDOverThresholdsSD 1.3.6.1.4.1.2011.5.25.111.8.1.1.4
The number of tests that violate OWD (One Way Delay) threshold from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsOWDOverThresholdsDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.5
The number of tests that violate OWD (One Way Delay) threshold from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsNumOfRTT 1.3.6.1.4.1.2011.5.25.111.8.1.1.6
The number of RTTs that are successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsRTTSum 1.3.6.1.4.1.2011.5.25.111.8.1.1.7
The sum of RTTs that are successfully measured.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsRTTSum2Low 1.3.6.1.4.1.2011.5.25.111.8.1.1.8
The sum of squares of RTTs that are successfully measured by tests (low order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsRTTSum2High 1.3.6.1.4.1.2011.5.25.111.8.1.1.9
The sum of squares of RTTs that are successfully measured by tests (high order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsRTTMin 1.3.6.1.4.1.2011.5.25.111.8.1.1.10
The minimum of RTTs that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsRTTMax 1.3.6.1.4.1.2011.5.25.111.8.1.1.11
The maximum of RTTs that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsMinOfPositivesSD 1.3.6.1.4.1.2011.5.25.111.8.1.1.12
The minimum of absolute value of all positive jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsMaxOfPositivesSD 1.3.6.1.4.1.2011.5.25.111.8.1.1.13
The maximum of absolute value of all positive jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsNumOfPositivesSD 1.3.6.1.4.1.2011.5.25.111.8.1.1.14
The number of all positive jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsSumOfPositivesSD 1.3.6.1.4.1.2011.5.25.111.8.1.1.15
The sum of absolute value of all positive jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsSum2OfPositivesSDLow 1.3.6.1.4.1.2011.5.25.111.8.1.1.16
The sum of squares of absolute value of all positive jitter values from source to destination (low order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsSum2OfPositivesSDHigh 1.3.6.1.4.1.2011.5.25.111.8.1.1.17
The sum of squares of absolute value of all positive jitter values from source to destination (high order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsMinOfNegativesSD 1.3.6.1.4.1.2011.5.25.111.8.1.1.18
The minimum of absolute value of all negative jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsMaxOfNegativesSD 1.3.6.1.4.1.2011.5.25.111.8.1.1.19
The maximum of absolute value of all negative jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsNumOfNegativesSD 1.3.6.1.4.1.2011.5.25.111.8.1.1.20
The number of all negative jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsSumOfNegativesSD 1.3.6.1.4.1.2011.5.25.111.8.1.1.21
The sum of absolute value of all negative jitter values from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsSum2OfNegativesSDLow 1.3.6.1.4.1.2011.5.25.111.8.1.1.22
The sum of squares of absolute value of all negative values from source to destination (low order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsSum2OfNegativesSDHigh 1.3.6.1.4.1.2011.5.25.111.8.1.1.23
The sum of squares of absolute value of all negative values from source to destination (high order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsMinOfPositivesDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.24
The minimum of absolute value of all positive jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsMaxOfPositivesDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.25
The maximum of absolute value of all positive jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsNumOfPositivesDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.26
The number of all positive jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsSumOfPositivesDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.27
The sum of absolute value of all positive jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsSum2OfPositivesDSLow 1.3.6.1.4.1.2011.5.25.111.8.1.1.28
The sum of squares of absolute value of all positive jitter values from destination to source (low order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsSum2OfPositivesDSHigh 1.3.6.1.4.1.2011.5.25.111.8.1.1.29
The sum of squares of absolute value of all positive jitter values from destination to source (high order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsMinOfNegativesDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.30
The minimum of absolute value of all negative jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsMaxOfNegativesDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.31
The maximum of absolute value of all negative jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsNumOfNegativesDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.32
The number of all negative jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsSumOfNegativesDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.33
The sum of absolute value of all negative jitter values from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsSum2OfNegativesDSLow 1.3.6.1.4.1.2011.5.25.111.8.1.1.34
The sum of squares of absolute value of all negative values from destination to source (low order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsSum2OfNegativesDSHigh 1.3.6.1.4.1.2011.5.25.111.8.1.1.35
The sum of squares of absolute value of all negative values from destination to source (high order 32 bits).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsMaxDelaySD 1.3.6.1.4.1.2011.5.25.111.8.1.1.36
The maximum of all OWD (One Way Delay) from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsMaxDelayDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.37
The maximum of all OWD (One Way Delay) from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsNumOfOWD 1.3.6.1.4.1.2011.5.25.111.8.1.1.38
The number of OWDs that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsOWSumSD 1.3.6.1.4.1.2011.5.25.111.8.1.1.39
The sum of OWDs that were successfully measured by tests from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsOWSumDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.40
The sum of OWDs that were successfully measured by tests from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsPacketLossSD 1.3.6.1.4.1.2011.5.25.111.8.1.1.41
The number of packets lost when sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsPacketLossDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.42
The number of packets lost when sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsPacketLossUnknown 1.3.6.1.4.1.2011.5.25.111.8.1.1.43
The number of packets lost for which we can't determine the direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsPacketOutOfSequences 1.3.6.1.4.1.2011.5.25.111.8.1.1.44
The number of packets arrived out of sequence.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsPacketLossRatio 1.3.6.1.4.1.2011.5.25.111.8.1.1.45
The ratio of the packets lost to all packets sent in the test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsErrors 1.3.6.1.4.1.2011.5.25.111.8.1.1.46
The number of errors occurred in the test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsBusies 1.3.6.1.4.1.2011.5.25.111.8.1.1.47
The number of occasions when a test couldn't be initialized because the previous test has not completed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsTimeouts 1.3.6.1.4.1.2011.5.25.111.8.1.1.48
The number of responses arrived over the time.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsProbeResponses 1.3.6.1.4.1.2011.5.25.111.8.1.1.49
The number of responses from echo-server for the packets sent by the test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsSentProbes 1.3.6.1.4.1.2011.5.25.111.8.1.1.50
The number of packets sent in the test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsDrops 1.3.6.1.4.1.2011.5.25.111.8.1.1.51
The number of packets that were sent failed in the test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsRTTAvg 1.3.6.1.4.1.2011.5.25.111.8.1.1.52
The average of RTTs that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsAvgJitter 1.3.6.1.4.1.2011.5.25.111.8.1.1.53
The average of jitter values that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsAvgJitterSD 1.3.6.1.4.1.2011.5.25.111.8.1.1.54
The average of jitter values from source to destination that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsAvgJitterDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.55
The average of jitter values from destination to source that were successfully measured by tests.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsJitterOut 1.3.6.1.4.1.2011.5.25.111.8.1.1.56
Jitter (RFC1889) at responder.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaJitterCollectStatsJitterIn 1.3.6.1.4.1.2011.5.25.111.8.1.1.57
Jitter (RFC1889) at sender.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nqaJitterCollectStatsMinDelaySD 1.3.6.1.4.1.2011.5.25.111.8.1.1.58
The minimum of all OWD (One Way Delay) from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsMinDelayDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.59
The minimum of all OWD (One Way Delay) from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsAvgDelaySD 1.3.6.1.4.1.2011.5.25.111.8.1.1.60
The average of all OWD (One Way Delay) from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsAvgDelayDS 1.3.6.1.4.1.2011.5.25.111.8.1.1.61
The average of all OWD (One Way Delay) from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsPktRewriteNum 1.3.6.1.4.1.2011.5.25.111.8.1.1.62
The number of all the packets have been rewrited.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsPktRewriteRatio 1.3.6.1.4.1.2011.5.25.111.8.1.1.63
The ratio of all the packets have been rewrited.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsPktDisorderNum 1.3.6.1.4.1.2011.5.25.111.8.1.1.64
The number of all the packets have been disordered.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsPktDisorderRatio 1.3.6.1.4.1.2011.5.25.111.8.1.1.65
The ratio of all the packets have been disordered.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaJitterCollectStatsFragPktDisorderNum 1.3.6.1.4.1.2011.5.25.111.8.1.1.66
The number of all the packets whose fragments have been disordered.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nqaJitterCollectStatsFragPktDisorderRatio 1.3.6.1.4.1.2011.5.25.111.8.1.1.67
The ratio of all the packets whose fragments have been disordered.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nqaAlarm 1.3.6.1.4.1.2011.5.25.111.9
OBJECT IDENTIFIER    

nqaMaxAlarmNum 1.3.6.1.4.1.2011.5.25.111.9.1
Maximum number of alarms.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

nqaMaxEventNum 1.3.6.1.4.1.2011.5.25.111.9.2
Maximum number of events that alarms can trigger.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

nqaAlarmTable 1.3.6.1.4.1.2011.5.25.111.9.3
A list of alarm entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaAlarmEntry

nqaAlarmEntry 1.3.6.1.4.1.2011.5.25.111.9.3.1
A list of parameters that set up a periodic checking for alarm conditions.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaAlarmEntry  

nqaAlarmIndex 1.3.6.1.4.1.2011.5.25.111.9.3.1.1
Uniquely identifies a row in the nqaAlarmTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

nqaAlarmVariable 1.3.6.1.4.1.2011.5.25.111.9.3.1.11
The type of the particular variable to be sampled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER rttAvg(1), lostPacketRatio(2), packetLossSd(3), packetLossDs(4), jitterRavg(5), jitterSdAvg(6), jitterDsAvg(7)  

nqaAlarmSampleType 1.3.6.1.4.1.2011.5.25.111.9.3.1.12
delta(1): relative value absolute(2): absolute value Relative value: indicates the relative value to the last sampling. Currently, only absolute(2) is supported.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER delta(1), absolute(2)  

nqaAlarmValue 1.3.6.1.4.1.2011.5.25.111.9.3.1.13
The actual value of the monitored object is compared with the upper limit and lower limit.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

nqaAlarmStartUpNqaAlarm 1.3.6.1.4.1.2011.5.25.111.9.3.1.14
The alarm that may be sent when this entry is first set to valid. If the first sample after this entry becomes valid is greater than or equal to the risingThreshold and alarmStartupAlarm is equal to risingAlarm(1) or risingOrFallingAlarm(3), then a single rising alarm will be generated. If the first sample after this entry becomes valid is less than or equal to the fallingThreshold and alarmStartupAlarm is equal to fallingAlarm(2) or risingOrFallingAlarm(3), then a single falling alarm will be generated.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER risingAlarm(1), fallingAlarm(2), risingOrFallingAlarm(3)  

nqaAlarmRisingThreshold 1.3.6.1.4.1.2011.5.25.111.9.3.1.15
Set the upper limit of the alarm.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

nqaAlarmFallingThreshold 1.3.6.1.4.1.2011.5.25.111.9.3.1.16
Set the lower limit of the alarm.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

nqaAlarmRisingEventIndex 1.3.6.1.4.1.2011.5.25.111.9.3.1.17
Index of the event triggered when the node value exceeds the upper limit.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

nqaAlarmFallingEventIndex 1.3.6.1.4.1.2011.5.25.111.9.3.1.18
Index of the event triggered when the node value is under the lower limit.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

nqaAlarmDescription 1.3.6.1.4.1.2011.5.25.111.9.3.1.19
Alarm Description.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..127)  

nqaAlarmStatus 1.3.6.1.4.1.2011.5.25.111.9.3.1.51
The status of the alarm row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

nqaEventTable 1.3.6.1.4.1.2011.5.25.111.9.4
A list of events to be generated.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NqaEventEntry

nqaEventEntry 1.3.6.1.4.1.2011.5.25.111.9.4.1
A set of parameters that describe an event to be generated when certain conditions are met.
Status: current Access: not-accessible
OBJECT-TYPE    
  NqaEventEntry  

nqaEventIndex 1.3.6.1.4.1.2011.5.25.111.9.4.1.1
Uniquely identifies a row in the nqaEventTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

nqaEventType 1.3.6.1.4.1.2011.5.25.111.9.4.1.11
Event type, that is, behaviors for processing events: none(1): no behavior log(2): keeping logs trap(3): sending trap messages logandtrap(4): keeping logs and sending trap messages linkage(5): start the linkaged test-instance.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), log(2), trap(3), logAndTrap(4), linkage(5)  

nqaEventDescription 1.3.6.1.4.1.2011.5.25.111.9.4.1.12
Event description.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..127)  

nqaEventAdminName 1.3.6.1.4.1.2011.5.25.111.9.4.1.13
Administrator name of event test instance.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

nqaEventOperationTag 1.3.6.1.4.1.2011.5.25.111.9.4.1.14
Operation tag of event test instance.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

nqaEventStatus 1.3.6.1.4.1.2011.5.25.111.9.4.1.51
The status of the event row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

nqaSaveRecord 1.3.6.1.4.1.2011.5.25.111.10
OBJECT IDENTIFIER    

nqaFtpSaveRecordEnable 1.3.6.1.4.1.2011.5.25.111.10.1
Identifies whether saving test results to the FTP server through FTP is enabled. enable(1) disable(2) By default, the value is disable(2).
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

nqaFtpSaveRecordIpAddr 1.3.6.1.4.1.2011.5.25.111.10.2
Set the IP address of the FTP server to which test results are saved.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

nqaFtpSaveRecordVrfName 1.3.6.1.4.1.2011.5.25.111.10.3
Set the name of the VRF instance for the FTP server to which test results are saved.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..31)  

nqaFtpSaveRecordUserName 1.3.6.1.4.1.2011.5.25.111.10.4
Set the user name of the FTP server to which test results are saved.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

nqaFtpSaveRecordPassword 1.3.6.1.4.1.2011.5.25.111.10.5
Set the password used when the test results are saved to the FTP server.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

nqaFtpSaveRecordFileName 1.3.6.1.4.1.2011.5.25.111.10.6
Set the file name of used by the FTP server to save test results.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..200)  

nqaFtpSaveRecordItemNum 1.3.6.1.4.1.2011.5.25.111.10.7
The value of this object identifies the number of NQA test results that can be saved in a file created on the FTP server. The default value is 100000.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10000..2147483647  

nqaFtpSaveRecordTime 1.3.6.1.4.1.2011.5.25.111.10.8
The value of this object identifies the duration that NQA test results can be saved in a file created on the FTP server. The default duration is 60 minutes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..43200  

nqaFtpSaveRecordNotificationEnable 1.3.6.1.4.1.2011.5.25.111.10.9
Set whether to send trap messages when saving test results to the FTP server is completed. By default, the value is disable(2).
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

nqaFtpSaveRecordLastFileName 1.3.6.1.4.1.2011.5.25.111.10.10
Set the name of the file used to save the last test record to the FTP server.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..220)