Nortel-Magellan-Passport-FrameRelayDteMIB

File: Nortel-Magellan-Passport-FrameRelayDteMIB.mib (142848 bytes)

Imported modules

RFC-1212 Nortel-Magellan-Passport-UsefulDefinitionsMIB Nortel-Magellan-Passport-StandardTextualConventionsMIB
Nortel-Magellan-Passport-TextualConventionsMIB

Imported symbols

OBJECT-TYPE components passportMIBs
Counter32 DisplayString StorageType
RowStatus PassportCounter64 InterfaceIndex
Gauge32 Integer32 Unsigned32
DashedHexString NonReplicated HexString
EnterpriseDateAndTime Link

Defined Types

FrDteRowStatusEntry  
SEQUENCE    
  frDteRowStatus RowStatus
  frDteComponentName DisplayString
  frDteStorageType StorageType
  frDteIndex Integer32

FrDteCidDataEntry  
SEQUENCE    
  frDteCustomerIdentifier Unsigned32

FrDteIfEntryEntry  
SEQUENCE    
  frDteIfAdminStatus INTEGER
  frDteIfIndex InterfaceIndex

FrDteProvEntry  
SEQUENCE    
  frDteAcceptUndefinedDlci INTEGER

FrDteStateEntry  
SEQUENCE    
  frDteAdminState INTEGER
  frDteOperationalState INTEGER
  frDteUsageState INTEGER

FrDteOperStatusEntry  
SEQUENCE    
  frDteSnmpOperStatus INTEGER

FrDteOperEntry  
SEQUENCE    
  frDteLinkOperState INTEGER

FrDteErrEntry  
SEQUENCE    
  frDteErrType INTEGER
  frDteErrData HexString
  frDteErrTime EnterpriseDateAndTime
  frDteErrDiscards Counter32
  frDteErrFaults Counter32
  frDteErrFaultTime EnterpriseDateAndTime

FrDteErrStatsEntry  
SEQUENCE    
  frDteXmitDiscardPvcDown Counter32
  frDteXmitDiscardLmiInactive Counter32
  frDteXmitDiscardFramerDown Counter32
  frDteXmitDiscardPvcInactive Counter32
  frDteXmitDiscardCirExceeded Counter32
  frDteRecvDiscardPvcDown Counter32
  frDteRecvDiscardLmiInactive Counter32
  frDteRecvDiscardPvcInactive Counter32
  frDteBadFc Counter32
  frDteUlpUnknownProtocol Counter32
  frDteDefragSequenceErrors Counter32
  frDteReceiveShort Counter32
  frDteIllegalDlci Counter32
  frDteDlcmiProtoErr Counter32
  frDteDlcmiUnknownIe Counter32
  frDteDlcmiSequenceErr Counter32
  frDteDlcmiUnknownRpt Counter32

FrDteFramerRowStatusEntry  
SEQUENCE    
  frDteFramerRowStatus RowStatus
  frDteFramerComponentName DisplayString
  frDteFramerStorageType StorageType
  frDteFramerIndex NonReplicated

FrDteFramerProvEntry  
SEQUENCE    
  frDteFramerInterfaceName Link

FrDteFramerStateEntry  
SEQUENCE    
  frDteFramerAdminState INTEGER
  frDteFramerOperationalState INTEGER
  frDteFramerUsageState INTEGER

FrDteFramerStatsEntry  
SEQUENCE    
  frDteFramerFrmToIf Counter32
  frDteFramerFrmFromIf Counter32
  frDteFramerAborts Counter32
  frDteFramerCrcErrors Counter32
  frDteFramerLrcErrors Counter32
  frDteFramerNonOctetErrors Counter32
  frDteFramerOverruns Counter32
  frDteFramerUnderruns Counter32
  frDteFramerLargeFrmErrors Counter32

FrDteFramerUtilEntry  
SEQUENCE    
  frDteFramerNormPrioLinkUtilToIf Gauge32
  frDteFramerNormPrioLinkUtilFromIf Gauge32

FrDteLmiRowStatusEntry  
SEQUENCE    
  frDteLmiRowStatus RowStatus
  frDteLmiComponentName DisplayString
  frDteLmiStorageType StorageType
  frDteLmiIndex NonReplicated

FrDteLmiProvEntry  
SEQUENCE    
  frDteLmiProcedures INTEGER
  frDteLmiPollingInterval Unsigned32
  frDteLmiFullEnquiryInterval Unsigned32
  frDteLmiErrorThreshold Unsigned32
  frDteLmiMonitoredEvents Unsigned32

FrDteLmiOperEntry  
SEQUENCE    
  frDteLmiLmiStatus INTEGER

FrDteRgRowStatusEntry  
SEQUENCE    
  frDteRgRowStatus RowStatus
  frDteRgComponentName DisplayString
  frDteRgStorageType StorageType
  frDteRgIndex Integer32

FrDteRgIfEntryEntry  
SEQUENCE    
  frDteRgIfAdminStatus INTEGER
  frDteRgIfIndex InterfaceIndex

FrDteRgProvEntry  
SEQUENCE    
  frDteRgMaxTransmissionUnit Unsigned32

FrDteRgMpEntry  
SEQUENCE    
  frDteRgLinkToProtocolPort Link

FrDteRgStateEntry  
SEQUENCE    
  frDteRgAdminState INTEGER
  frDteRgOperationalState INTEGER
  frDteRgUsageState INTEGER

FrDteRgOperStatusEntry  
SEQUENCE    
  frDteRgSnmpOperStatus INTEGER

FrDteRgLtDlciEntry  
SEQUENCE    
  frDteRgLtDlciValue Link
  frDteRgLtDlciRowStatus RowStatus

FrDteRgBfrRowStatusEntry  
SEQUENCE    
  frDteRgBfrRowStatus RowStatus
  frDteRgBfrComponentName DisplayString
  frDteRgBfrStorageType StorageType
  frDteRgBfrIndex NonReplicated

FrDteRgBfrProvEntry  
SEQUENCE    
  frDteRgBfrMacType INTEGER
  frDteRgBfrBfrIndex INTEGER

FrDteRgBfrOprEntry  
SEQUENCE    
  frDteRgBfrMacAddr DashedHexString

FrDteDynDlciDefsRowStatusEntry  
SEQUENCE    
  frDteDynDlciDefsRowStatus RowStatus
  frDteDynDlciDefsComponentName DisplayString
  frDteDynDlciDefsStorageType StorageType
  frDteDynDlciDefsIndex NonReplicated

FrDteDynDlciDefsProvEntry  
SEQUENCE    
  frDteDynDlciDefsStdRowStatus INTEGER
  frDteDynDlciDefsRateEnforcement INTEGER
  frDteDynDlciDefsCommittedInformationRate Unsigned32
  frDteDynDlciDefsCommittedBurst Unsigned32
  frDteDynDlciDefsExcessBurst Unsigned32
  frDteDynDlciDefsExcessBurstAction INTEGER
  frDteDynDlciDefsIpCos Unsigned32

FrDteStDlciRowStatusEntry  
SEQUENCE    
  frDteStDlciRowStatus RowStatus
  frDteStDlciComponentName DisplayString
  frDteStDlciStorageType StorageType
  frDteStDlciIndex Integer32

FrDteStDlciProvEntry  
SEQUENCE    
  frDteStDlciStdRowStatus INTEGER
  frDteStDlciRateEnforcement INTEGER
  frDteStDlciCommittedInformationRate Unsigned32
  frDteStDlciCommittedBurst Unsigned32
  frDteStDlciExcessBurst Unsigned32
  frDteStDlciExcessBurstAction INTEGER
  frDteStDlciIpCos Unsigned32

FrDteStDlciRgLinkEntry  
SEQUENCE    
  frDteStDlciLinkToRemoteGroup Link

FrDteStDlciHqRowStatusEntry  
SEQUENCE    
  frDteStDlciHqRowStatus RowStatus
  frDteStDlciHqComponentName DisplayString
  frDteStDlciHqStorageType StorageType
  frDteStDlciHqIndex NonReplicated

FrDteStDlciHqProvEntry  
SEQUENCE    
  frDteStDlciHqMaxPackets Unsigned32
  frDteStDlciHqMaxMsecData Unsigned32
  frDteStDlciHqMaxPercentMulticast Unsigned32
  frDteStDlciHqTimeToLive Unsigned32

FrDteStDlciHqStatsEntry  
SEQUENCE    
  frDteStDlciHqTimedOutPkt Counter32
  frDteStDlciHqQueuePurgeDiscards Counter32

FrDteStDlciHqTStatsEntry  
SEQUENCE    
  frDteStDlciHqTotalPktHandled Counter32
  frDteStDlciHqTotalPktForwarded Counter32
  frDteStDlciHqTotalPktQueued Counter32
  frDteStDlciHqTotalMulticastPkt Counter32
  frDteStDlciHqTotalPktDiscards Counter32

FrDteStDlciHqCStatsEntry  
SEQUENCE    
  frDteStDlciHqCurrentPktQueued Gauge32
  frDteStDlciHqCurrentBytesQueued Gauge32
  frDteStDlciHqCurrentMulticastQueued Gauge32

FrDteStDlciHqThrStatsEntry  
SEQUENCE    
  frDteStDlciHqQueuePktThreshold Unsigned32
  frDteStDlciHqPktThresholdExceeded Counter32
  frDteStDlciHqQueueByteThreshold Unsigned32
  frDteStDlciHqByteThresholdExceeded Counter32
  frDteStDlciHqQueueMulticastThreshold Unsigned32
  frDteStDlciHqMulThresholdExceeded Counter32
  frDteStDlciHqMemThresholdExceeded Counter32

FrDteLeqRowStatusEntry  
SEQUENCE    
  frDteLeqRowStatus RowStatus
  frDteLeqComponentName DisplayString
  frDteLeqStorageType StorageType
  frDteLeqIndex NonReplicated

FrDteLeqProvEntry  
SEQUENCE    
  frDteLeqMaxPackets Unsigned32
  frDteLeqMaxMsecData Unsigned32
  frDteLeqMaxPercentMulticast Unsigned32
  frDteLeqTimeToLive Unsigned32

FrDteLeqStatsEntry  
SEQUENCE    
  frDteLeqTimedOutPkt Counter32
  frDteLeqHardwareForcedPkt Counter32
  frDteLeqForcedPktDiscards Counter32
  frDteLeqQueuePurgeDiscards Counter32

FrDteLeqTStatsEntry  
SEQUENCE    
  frDteLeqTotalPktHandled Counter32
  frDteLeqTotalPktForwarded Counter32
  frDteLeqTotalPktQueued Counter32
  frDteLeqTotalMulticastPkt Counter32
  frDteLeqTotalPktDiscards Counter32

FrDteLeqCStatsEntry  
SEQUENCE    
  frDteLeqCurrentPktQueued Gauge32
  frDteLeqCurrentBytesQueued Gauge32
  frDteLeqCurrentMulticastQueued Gauge32

FrDteLeqThrStatsEntry  
SEQUENCE    
  frDteLeqQueuePktThreshold Unsigned32
  frDteLeqPktThresholdExceeded Counter32
  frDteLeqQueueByteThreshold Unsigned32
  frDteLeqByteThresholdExceeded Counter32
  frDteLeqQueueMulticastThreshold Unsigned32
  frDteLeqMulThresholdExceeded Counter32
  frDteLeqMemThresholdExceeded Counter32

FrDteDlciRowStatusEntry  
SEQUENCE    
  frDteDlciRowStatus RowStatus
  frDteDlciComponentName DisplayString
  frDteDlciStorageType StorageType
  frDteDlciIndex Integer32

FrDteDlciStateEntry  
SEQUENCE    
  frDteDlciAdminState INTEGER
  frDteDlciOperationalState INTEGER
  frDteDlciUsageState INTEGER

FrDteDlciOperEntry  
SEQUENCE    
  frDteDlciDlciState INTEGER
  frDteDlciLastTimeChange EnterpriseDateAndTime
  frDteDlciSentFrames Counter32
  frDteDlciSentOctets Counter32
  frDteDlciReceivedFrames Counter32
  frDteDlciReceivedOctets Counter32
  frDteDlciReceivedFECNs Counter32
  frDteDlciReceivedBECNs Counter32
  frDteDlciDiscardedFrames Counter32
  frDteDlciCreationType INTEGER
  frDteDlciCreationTime EnterpriseDateAndTime
  frDteDlciRateEnforcement INTEGER
  frDteDlciCommittedInformationRate Gauge32
  frDteDlciCommittedBurst Unsigned32
  frDteDlciExcessBurst Unsigned32
  frDteDlciExcessBurstAction INTEGER

FrDteVFramerRowStatusEntry  
SEQUENCE    
  frDteVFramerRowStatus RowStatus
  frDteVFramerComponentName DisplayString
  frDteVFramerStorageType StorageType
  frDteVFramerIndex NonReplicated

FrDteVFramerProvEntry  
SEQUENCE    
  frDteVFramerOtherVirtualFramer Link
  frDteVFramerLogicalProcessor Link

FrDteVFramerStateEntry  
SEQUENCE    
  frDteVFramerAdminState INTEGER
  frDteVFramerOperationalState INTEGER
  frDteVFramerUsageState INTEGER

FrDteVFramerStatsEntry  
SEQUENCE    
  frDteVFramerFrmToOtherVFramer PassportCounter64
  frDteVFramerFrmFromOtherVFramer PassportCounter64
  frDteVFramerOctetFromOtherVFramer PassportCounter64

Defined Values

frameRelayDteMIB 1.3.6.1.4.1.562.2.4.2.32
OBJECT IDENTIFIER    

frDte 1.3.6.1.4.1.562.2.4.1.101
OBJECT IDENTIFIER    

frDteRowStatusTable 1.3.6.1.4.1.562.2.4.1.101.1
This entry controls the addition and deletion of frDte components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteRowStatusEntry

frDteRowStatusEntry 1.3.6.1.4.1.562.2.4.1.101.1.1
A single entry in the table represents a single frDte component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteRowStatusEntry  

frDteRowStatus 1.3.6.1.4.1.562.2.4.1.101.1.1.1
This variable is used as the basis for SNMP naming of frDte components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frDteComponentName 1.3.6.1.4.1.562.2.4.1.101.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frDteStorageType 1.3.6.1.4.1.562.2.4.1.101.1.1.4
This variable represents the storage type value for the frDte tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frDteIndex 1.3.6.1.4.1.562.2.4.1.101.1.1.10
This variable represents the index for the frDte tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

frDteCidDataTable 1.3.6.1.4.1.562.2.4.1.101.20
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteCidDataEntry

frDteCidDataEntry 1.3.6.1.4.1.562.2.4.1.101.20.1
An entry in the frDteCidDataTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteCidDataEntry  

frDteCustomerIdentifier 1.3.6.1.4.1.562.2.4.1.101.20.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

frDteIfEntryTable 1.3.6.1.4.1.562.2.4.1.101.21
This group contains the provisionable attributes for the ifEntry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteIfEntryEntry

frDteIfEntryEntry 1.3.6.1.4.1.562.2.4.1.101.21.1
An entry in the frDteIfEntryTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteIfEntryEntry  

frDteIfAdminStatus 1.3.6.1.4.1.562.2.4.1.101.21.1.1
The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

frDteIfIndex 1.3.6.1.4.1.562.2.4.1.101.21.1.2
This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex 1..65535  

frDteProvTable 1.3.6.1.4.1.562.2.4.1.101.22
This group contains the provisioned attributes for the FrDte component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteProvEntry

frDteProvEntry 1.3.6.1.4.1.562.2.4.1.101.22.1
An entry in the frDteProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteProvEntry  

frDteAcceptUndefinedDlci 1.3.6.1.4.1.562.2.4.1.101.22.1.1
This parameter allows previously undefined Data Link Connection Identifiers (DLCIs) to be dynamically accepted in the default remote group. If set to enabled, undefined DLCIs will be accepted, if disabled, they will not.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

frDteStateTable 1.3.6.1.4.1.562.2.4.1.101.23
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteStateEntry

frDteStateEntry 1.3.6.1.4.1.562.2.4.1.101.23.1
An entry in the frDteStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteStateEntry  

frDteAdminState 1.3.6.1.4.1.562.2.4.1.101.23.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

frDteOperationalState 1.3.6.1.4.1.562.2.4.1.101.23.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

frDteUsageState 1.3.6.1.4.1.562.2.4.1.101.23.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

frDteOperStatusTable 1.3.6.1.4.1.562.2.4.1.101.24
This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteOperStatusEntry

frDteOperStatusEntry 1.3.6.1.4.1.562.2.4.1.101.24.1
An entry in the frDteOperStatusTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteOperStatusEntry  

frDteSnmpOperStatus 1.3.6.1.4.1.562.2.4.1.101.24.1.1
The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

frDteOperTable 1.3.6.1.4.1.562.2.4.1.101.25
This group contains the operational attributes for the FrDte component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteOperEntry

frDteOperEntry 1.3.6.1.4.1.562.2.4.1.101.25.1
An entry in the frDteOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteOperEntry  

frDteLinkOperState 1.3.6.1.4.1.562.2.4.1.101.25.1.1
This attribute describes the operational state of the Link Control protocol. If the interface to the physical link hardware is inactive, the linkOperState is in the down state. The polling state only occurs when the Local Management Interface (LMI) is enabled and the physical link is active. The polling state indicates LMI is polling for its peer. Once communication is established the linkOperState will transition to the active state. If the procedure attribute of the Lmi component is set to none, linkOperState will transition to the active state once the physical link becomes active.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), down(2), polling(3)  

frDteErrTable 1.3.6.1.4.1.562.2.4.1.101.26
This group contains the SNMP frErrEntry attributes for the FrDte component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteErrEntry

frDteErrEntry 1.3.6.1.4.1.562.2.4.1.101.26.1
An entry in the frDteErrTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteErrEntry  

frDteErrType 1.3.6.1.4.1.562.2.4.1.101.26.1.2
The type of error that was last seen on this interface. The error types are as follows: receiveShort: This error indicates a received frame was discarded because it was less than four octets long or it was missing the Organizationally Unique Identifier (OUI) for a SNAP header. receiveLong: This error indicates a received frame was discarded because it was longer than expected. This error is currently not used on this interface. illegalDlci: This error indicates that a received frame was discarded because it's Q.922 address was not two octets in length. This error could also indicate that a frame was discarded because it was received on a DLCI reserved for LMI which had not been provisioned active. dlcmiProtoErr: This error indicates an LMI frame was received with contents formatted incorrectly. dlcmiUnknownIe: This error indicates that an LMI frame was received which contained an unsupported Information Element (IE) type dlcmiSequenceErr: This error indicates that an LMI frame was received whose Keep Alive Sequence was incorrect. dlcmiUnknownRpt: This error indicates that an LMI frame was received which contained a Report-type Information Element with an invalid type of report. noErrorSinceReset: This error type indicates that there has not been an error since the interface has been reset. unknownError: This error type contains the cumulation of receive frame errors that did not fit one of the MIB error descriptions above. These errors include those counted by the following attributes: ulpUnknownProtocol - A received frame was discarded because the Upper Level Protocol (ULP) encapsulation used was unsupported. badFc - A received frame was discarded because the frame control character was incorrect. defragSequenceErrors - A fragment was received which was discarded due to an out of sequence error detection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unknownError(1), receiveShort(2), receiveLong(3), illegalDlci(4), dlcmiProtoErr(5), dlcmiUnknownIe(6), dlcmiSequenceErr(7), dlcmiUnknownRpt(8), noErrorSinceReset(9)  

frDteErrData 1.3.6.1.4.1.562.2.4.1.101.26.1.3
An octet string containing the first part of the frame in which an error was last detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(64)  

frDteErrTime 1.3.6.1.4.1.562.2.4.1.101.26.1.4
The time at which the last error was detected and recorded in errType.
Status: mandatory Access: read-only
OBJECT-TYPE    
  EnterpriseDateAndTime Size(0|19)  

frDteErrDiscards 1.3.6.1.4.1.562.2.4.1.101.26.1.6
Number of inbound frames dropped because of format errors or because the virtual circuit was not known. Format errors, in this case, are any errors which would prevent the system from recognizing the DLCI and placing the error in the discard category. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteErrFaults 1.3.6.1.4.1.562.2.4.1.101.26.1.7
This attribute counts the number of times LMI has taken down the interface. When the procedure attribute of the Lmi component is set to none, this counter will not be incremented. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteErrFaultTime 1.3.6.1.4.1.562.2.4.1.101.26.1.8
The last time the errFaults counter was incremented.
Status: mandatory Access: read-only
OBJECT-TYPE    
  EnterpriseDateAndTime Size(0|19)  

frDteErrStatsTable 1.3.6.1.4.1.562.2.4.1.101.27
This group contains error counters for the FrDte.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteErrStatsEntry

frDteErrStatsEntry 1.3.6.1.4.1.562.2.4.1.101.27.1
An entry in the frDteErrStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteErrStatsEntry  

frDteXmitDiscardPvcDown 1.3.6.1.4.1.562.2.4.1.101.27.1.1
Count of transmitted frames discarded because the Dlci or a component positioned in a hierarchically fashion above it (e.g. it's remote group or the FrDte component) was administratively disabled. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteXmitDiscardLmiInactive 1.3.6.1.4.1.562.2.4.1.101.27.1.2
Count of transmitted frames discarded because the Local Management Interface (LMI) was not yet active (i.e. LMI was still in the polling state). This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteXmitDiscardFramerDown 1.3.6.1.4.1.562.2.4.1.101.27.1.3
Count of transmitted frames discarded because the framer component was down. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteXmitDiscardPvcInactive 1.3.6.1.4.1.562.2.4.1.101.27.1.4
Count of transmitted frames discarded because the Local Management Interface (LMI) had inactivated or invalidated the Dlci. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteXmitDiscardCirExceeded 1.3.6.1.4.1.562.2.4.1.101.27.1.5
Count of transmitted frames discarded because CIR was enabled on a Dlci without a HibernationQueue subcomponent and the traffic exceeded the combined Committed and Excess Burst thresholds. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteRecvDiscardPvcDown 1.3.6.1.4.1.562.2.4.1.101.27.1.6
Count of received frames discarded because the Dlci or a component positioned in a hierarchically fashion above it (e.g. it's remote group or the FrDte component) was administratively disabled. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteRecvDiscardLmiInactive 1.3.6.1.4.1.562.2.4.1.101.27.1.7
Count of received frames discarded because the Local Management Interface (LMI) was not yet active (i.e. LMI was still in the polling state). This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteRecvDiscardPvcInactive 1.3.6.1.4.1.562.2.4.1.101.27.1.8
Count of received frames discarded because the Local Management Interface (LMI) had inactivated or invalidated the Dlci. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteBadFc 1.3.6.1.4.1.562.2.4.1.101.27.1.9
Count of received frames discarded because the frame control character was incorrect. This may indicate that the other side of the link is configured for a different link level protocol. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteUlpUnknownProtocol 1.3.6.1.4.1.562.2.4.1.101.27.1.10
Count of received frames discarded because the Upper Level Protocol (ULP) encapsulation used was unsupported. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteDefragSequenceErrors 1.3.6.1.4.1.562.2.4.1.101.27.1.11
Count of fragments received which were discarded due to out of sequence error detection. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteReceiveShort 1.3.6.1.4.1.562.2.4.1.101.27.1.12
Count of received frames (including LMI frames) discarded because they were less than four octets long or they were missing the Organizationally Unique Identifier (OUI) for a SNAP header. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteIllegalDlci 1.3.6.1.4.1.562.2.4.1.101.27.1.13
Count of received frames discarded because their Q.922 address was not two octets in length. This count also includes frames discarded because they were received on a Dlci reserved for LMI which had not been provisioned active. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteDlcmiProtoErr 1.3.6.1.4.1.562.2.4.1.101.27.1.14
Count of received LMI frames whose contents were formatted incorrectly. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteDlcmiUnknownIe 1.3.6.1.4.1.562.2.4.1.101.27.1.15
Count of received LMI frames which contained an unsupported Information Element (IE) type. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteDlcmiSequenceErr 1.3.6.1.4.1.562.2.4.1.101.27.1.16
Count of received LMI frames whose Keep Alive Sequence was incorrect. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteDlcmiUnknownRpt 1.3.6.1.4.1.562.2.4.1.101.27.1.17
Count of received LMI frames which contained a Report-type Information Element with an invalid type of report. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteFramer 1.3.6.1.4.1.562.2.4.1.101.2
OBJECT IDENTIFIER    

frDteFramerRowStatusTable 1.3.6.1.4.1.562.2.4.1.101.2.1
This entry controls the addition and deletion of frDteFramer components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteFramerRowStatusEntry

frDteFramerRowStatusEntry 1.3.6.1.4.1.562.2.4.1.101.2.1.1
A single entry in the table represents a single frDteFramer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteFramerRowStatusEntry  

frDteFramerRowStatus 1.3.6.1.4.1.562.2.4.1.101.2.1.1.1
This variable is used as the basis for SNMP naming of frDteFramer components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frDteFramerComponentName 1.3.6.1.4.1.562.2.4.1.101.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frDteFramerStorageType 1.3.6.1.4.1.562.2.4.1.101.2.1.1.4
This variable represents the storage type value for the frDteFramer tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frDteFramerIndex 1.3.6.1.4.1.562.2.4.1.101.2.1.1.10
This variable represents the index for the frDteFramer tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frDteFramerProvTable 1.3.6.1.4.1.562.2.4.1.101.2.10
This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisional Framer groups.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteFramerProvEntry

frDteFramerProvEntry 1.3.6.1.4.1.562.2.4.1.101.2.10.1
An entry in the frDteFramerProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteFramerProvEntry  

frDteFramerInterfaceName 1.3.6.1.4.1.562.2.4.1.101.2.10.1.1
This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

frDteFramerStateTable 1.3.6.1.4.1.562.2.4.1.101.2.12
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteFramerStateEntry

frDteFramerStateEntry 1.3.6.1.4.1.562.2.4.1.101.2.12.1
An entry in the frDteFramerStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteFramerStateEntry  

frDteFramerAdminState 1.3.6.1.4.1.562.2.4.1.101.2.12.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

frDteFramerOperationalState 1.3.6.1.4.1.562.2.4.1.101.2.12.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

frDteFramerUsageState 1.3.6.1.4.1.562.2.4.1.101.2.12.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

frDteFramerStatsTable 1.3.6.1.4.1.562.2.4.1.101.2.13
This group contains the operational statistics data for a Framer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteFramerStatsEntry

frDteFramerStatsEntry 1.3.6.1.4.1.562.2.4.1.101.2.13.1
An entry in the frDteFramerStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteFramerStatsEntry  

frDteFramerFrmToIf 1.3.6.1.4.1.562.2.4.1.101.2.13.1.1
This attribute counts the number of frames transmitted to the link interface by Framer. Note: This does not include the number of frames transmitted directly to the hardware queue, thus bypassing the Framer component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteFramerFrmFromIf 1.3.6.1.4.1.562.2.4.1.101.2.13.1.2
This attribute counts the number of frames received from the link interface by Framer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteFramerAborts 1.3.6.1.4.1.562.2.4.1.101.2.13.1.3
This attribute counts the total number of aborts received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteFramerCrcErrors 1.3.6.1.4.1.562.2.4.1.101.2.13.1.4
This attribute counts the total number of frames with CRC errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteFramerLrcErrors 1.3.6.1.4.1.562.2.4.1.101.2.13.1.5
This attribute counts the total number of frames with LRC errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteFramerNonOctetErrors 1.3.6.1.4.1.562.2.4.1.101.2.13.1.6
This attribute counts the total number of frames that were non octet aligned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteFramerOverruns 1.3.6.1.4.1.562.2.4.1.101.2.13.1.7
This attribute counts the total number of frames received from the link for which overruns occurred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteFramerUnderruns 1.3.6.1.4.1.562.2.4.1.101.2.13.1.8
This attribute counts the total number of frames transmitted to the link for which underruns occurred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteFramerLargeFrmErrors 1.3.6.1.4.1.562.2.4.1.101.2.13.1.9
This attribute counts the total number of frames received which were too large. The frame exceeded the maximumFrameLengthLimit provisioned attribute or it contained more than the 255 block hardware limit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteFramerUtilTable 1.3.6.1.4.1.562.2.4.1.101.2.14
This group contains the link utilization operational data for a Framer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteFramerUtilEntry

frDteFramerUtilEntry 1.3.6.1.4.1.562.2.4.1.101.2.14.1
An entry in the frDteFramerUtilTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteFramerUtilEntry  

frDteFramerNormPrioLinkUtilToIf 1.3.6.1.4.1.562.2.4.1.101.2.14.1.1
This attribute is the utilization of the normal priority data sent to the link as a percentage of the available bandwidth on the link. The utilization is the average for the last minute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..100  

frDteFramerNormPrioLinkUtilFromIf 1.3.6.1.4.1.562.2.4.1.101.2.14.1.3
This attribute is the utilization of the normal priority data received from the link as a percentage of the available bandwidth on the link. The utilization is the average for the last minute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..100  

frDteLmi 1.3.6.1.4.1.562.2.4.1.101.3
OBJECT IDENTIFIER    

frDteLmiRowStatusTable 1.3.6.1.4.1.562.2.4.1.101.3.1
This entry controls the addition and deletion of frDteLmi components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteLmiRowStatusEntry

frDteLmiRowStatusEntry 1.3.6.1.4.1.562.2.4.1.101.3.1.1
A single entry in the table represents a single frDteLmi component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteLmiRowStatusEntry  

frDteLmiRowStatus 1.3.6.1.4.1.562.2.4.1.101.3.1.1.1
This variable is used as the basis for SNMP naming of frDteLmi components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

frDteLmiComponentName 1.3.6.1.4.1.562.2.4.1.101.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frDteLmiStorageType 1.3.6.1.4.1.562.2.4.1.101.3.1.1.4
This variable represents the storage type value for the frDteLmi tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frDteLmiIndex 1.3.6.1.4.1.562.2.4.1.101.3.1.1.10
This variable represents the index for the frDteLmi tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frDteLmiProvTable 1.3.6.1.4.1.562.2.4.1.101.3.10
This group contains the provisioned attributes for the Lmi component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteLmiProvEntry

frDteLmiProvEntry 1.3.6.1.4.1.562.2.4.1.101.3.10.1
An entry in the frDteLmiProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteLmiProvEntry  

frDteLmiProcedures 1.3.6.1.4.1.562.2.4.1.101.3.10.1.1
This attribute selects the Local Management Interface (LMI) protocol to be used on the interface. This attribute is equivalent to the SNMP variable frDlcmiState. The vendorForum LMI protocol automatically implies that the DLCI used by the protocol is 1023. The ansi (T1.617 Annex D) and itu (ITU-T Recommendation Q.933 Annex A) LMI protocols use DLCI 0. If none is selected, no LMI procedures will run on the interface. Note that the ITU-T Recommendation Q.933 was previously a CCITT recommendation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), vendorForum(2), ansi(3), itu(5)  

frDteLmiPollingInterval 1.3.6.1.4.1.562.2.4.1.101.3.10.1.4
This is the number of seconds between successive status enquiry messages. This field corresponds to the parameter T391 described in the ANSI T1.617-1991 Annex D.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 5..30  

frDteLmiFullEnquiryInterval 1.3.6.1.4.1.562.2.4.1.101.3.10.1.5
The count of status polls before a full status enquiry message is issued. Every nth poll will request a full status. This field corresponds to the parameter N391 described in the ANSI T1.617-1991 Annex D.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

frDteLmiErrorThreshold 1.3.6.1.4.1.562.2.4.1.101.3.10.1.6
The number of errors detected within the monitored events window before declaring the link non-functional. This field corresponds to the parameter N392 described in the ANSI T1.617-1991 Annex D.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..10  

frDteLmiMonitoredEvents 1.3.6.1.4.1.562.2.4.1.101.3.10.1.7
The number of status polling intervals over which the errorthreshold is counted This is used to determine if the errorThreshold is exceeded. This field corresponds to the parameter N393 described in the ANSI T1.617-1991 Annex D.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..10  

frDteLmiOperTable 1.3.6.1.4.1.562.2.4.1.101.3.11
This group contains the operational attributes for the Lmi component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteLmiOperEntry

frDteLmiOperEntry 1.3.6.1.4.1.562.2.4.1.101.3.11.1
An entry in the frDteLmiOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteLmiOperEntry  

frDteLmiLmiStatus 1.3.6.1.4.1.562.2.4.1.101.3.11.1.2
This indicates the status of the Frame Relay interface as determined by the performance of the link management interface (LMI). If no LMI is running, lmiStatus will stay in the running state indefinitely.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER running(1), fault(2), initializing(3)  

frDteRg 1.3.6.1.4.1.562.2.4.1.101.4
OBJECT IDENTIFIER    

frDteRgRowStatusTable 1.3.6.1.4.1.562.2.4.1.101.4.1
This entry controls the addition and deletion of frDteRg components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteRgRowStatusEntry

frDteRgRowStatusEntry 1.3.6.1.4.1.562.2.4.1.101.4.1.1
A single entry in the table represents a single frDteRg component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteRgRowStatusEntry  

frDteRgRowStatus 1.3.6.1.4.1.562.2.4.1.101.4.1.1.1
This variable is used as the basis for SNMP naming of frDteRg components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frDteRgComponentName 1.3.6.1.4.1.562.2.4.1.101.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frDteRgStorageType 1.3.6.1.4.1.562.2.4.1.101.4.1.1.4
This variable represents the storage type value for the frDteRg tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frDteRgIndex 1.3.6.1.4.1.562.2.4.1.101.4.1.1.10
This variable represents the index for the frDteRg tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 1..256  

frDteRgIfEntryTable 1.3.6.1.4.1.562.2.4.1.101.4.10
This group contains the provisionable attributes for the ifEntry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteRgIfEntryEntry

frDteRgIfEntryEntry 1.3.6.1.4.1.562.2.4.1.101.4.10.1
An entry in the frDteRgIfEntryTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteRgIfEntryEntry  

frDteRgIfAdminStatus 1.3.6.1.4.1.562.2.4.1.101.4.10.1.1
The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

frDteRgIfIndex 1.3.6.1.4.1.562.2.4.1.101.4.10.1.2
This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex 1..65535  

frDteRgProvTable 1.3.6.1.4.1.562.2.4.1.101.4.11
This group contains the provisioned attributes for the Remote Group component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteRgProvEntry

frDteRgProvEntry 1.3.6.1.4.1.562.2.4.1.101.4.11.1
An entry in the frDteRgProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteRgProvEntry  

frDteRgMaxTransmissionUnit 1.3.6.1.4.1.562.2.4.1.101.4.11.1.1
The Maximum Transmission Unit size of the largest datagram (including Frame Relay header) which can be sent on the interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 262..9190  

frDteRgMpTable 1.3.6.1.4.1.562.2.4.1.101.4.12
This group contains the base provisioning data for the Media Application component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteRgMpEntry

frDteRgMpEntry 1.3.6.1.4.1.562.2.4.1.101.4.12.1
An entry in the frDteRgMpTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteRgMpEntry  

frDteRgLinkToProtocolPort 1.3.6.1.4.1.562.2.4.1.101.4.12.1.1
This attribute contains a protocol port component name. The attribute associates the application with a protocol port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

frDteRgStateTable 1.3.6.1.4.1.562.2.4.1.101.4.13
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteRgStateEntry

frDteRgStateEntry 1.3.6.1.4.1.562.2.4.1.101.4.13.1
An entry in the frDteRgStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteRgStateEntry  

frDteRgAdminState 1.3.6.1.4.1.562.2.4.1.101.4.13.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

frDteRgOperationalState 1.3.6.1.4.1.562.2.4.1.101.4.13.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

frDteRgUsageState 1.3.6.1.4.1.562.2.4.1.101.4.13.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

frDteRgOperStatusTable 1.3.6.1.4.1.562.2.4.1.101.4.14
This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteRgOperStatusEntry

frDteRgOperStatusEntry 1.3.6.1.4.1.562.2.4.1.101.4.14.1
An entry in the frDteRgOperStatusTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteRgOperStatusEntry  

frDteRgSnmpOperStatus 1.3.6.1.4.1.562.2.4.1.101.4.14.1.1
The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

frDteRgLtDlciTable 1.3.6.1.4.1.562.2.4.1.101.4.219
This attribute associates a Rg component with zero or more StDlci components. The Rg and StDlci components must be under the same FrDte component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteRgLtDlciEntry

frDteRgLtDlciEntry 1.3.6.1.4.1.562.2.4.1.101.4.219.1
An entry in the frDteRgLtDlciTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteRgLtDlciEntry  

frDteRgLtDlciValue 1.3.6.1.4.1.562.2.4.1.101.4.219.1.1
This variable represents both the value and the index for the frDteRgLtDlciTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

frDteRgLtDlciRowStatus 1.3.6.1.4.1.562.2.4.1.101.4.219.1.2
This variable is used to control the addition and deletion of individual values of the frDteRgLtDlciTable.
Status: mandatory Access: write-only
OBJECT-TYPE    
  RowStatus  

frDteRgBfr 1.3.6.1.4.1.562.2.4.1.101.4.15
OBJECT IDENTIFIER    

frDteRgBfrRowStatusTable 1.3.6.1.4.1.562.2.4.1.101.4.15.1
This entry controls the addition and deletion of frDteRgBfr components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteRgBfrRowStatusEntry

frDteRgBfrRowStatusEntry 1.3.6.1.4.1.562.2.4.1.101.4.15.1.1
A single entry in the table represents a single frDteRgBfr component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteRgBfrRowStatusEntry  

frDteRgBfrRowStatus 1.3.6.1.4.1.562.2.4.1.101.4.15.1.1.1
This variable is used as the basis for SNMP naming of frDteRgBfr components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frDteRgBfrComponentName 1.3.6.1.4.1.562.2.4.1.101.4.15.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frDteRgBfrStorageType 1.3.6.1.4.1.562.2.4.1.101.4.15.1.1.4
This variable represents the storage type value for the frDteRgBfr tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frDteRgBfrIndex 1.3.6.1.4.1.562.2.4.1.101.4.15.1.1.10
This variable represents the index for the frDteRgBfr tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frDteRgBfrProvTable 1.3.6.1.4.1.562.2.4.1.101.4.15.10
This group contains the provisioning attributes for the Bfr component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteRgBfrProvEntry

frDteRgBfrProvEntry 1.3.6.1.4.1.562.2.4.1.101.4.15.10.1
An entry in the frDteRgBfrProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteRgBfrProvEntry  

frDteRgBfrMacType 1.3.6.1.4.1.562.2.4.1.101.4.15.10.1.1
This attribute specifies the MAC address type of the Bfr component. The value must be chosen based on the media of the traffic source. For traffic originated from FDDI, use fddi; for ethernet, use enet; for token ring, use tokenRing
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER fddi(0), enet(1), tokenRing(2)  

frDteRgBfrBfrIndex 1.3.6.1.4.1.562.2.4.1.101.4.15.10.1.2
This attribute specifies the value which is used to derive a unique MAC address for the Bfr. The bfrIndex must be unique across all Bfrs on the same Lp.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..511  

frDteRgBfrOprTable 1.3.6.1.4.1.562.2.4.1.101.4.15.11
This group contains the operational attributes for the Bfr component..
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteRgBfrOprEntry

frDteRgBfrOprEntry 1.3.6.1.4.1.562.2.4.1.101.4.15.11.1
An entry in the frDteRgBfrOprTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteRgBfrOprEntry  

frDteRgBfrMacAddr 1.3.6.1.4.1.562.2.4.1.101.4.15.11.1.1
This attribute indicates the unique MAC address of the Bfr component. This value is derived by the value of the attribute bfrIndex. The value is displayed as cannonical format.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DashedHexString Size(6)  

frDteDynDlciDefs 1.3.6.1.4.1.562.2.4.1.101.5
OBJECT IDENTIFIER    

frDteDynDlciDefsRowStatusTable 1.3.6.1.4.1.562.2.4.1.101.5.1
This entry controls the addition and deletion of frDteDynDlciDefs components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteDynDlciDefsRowStatusEntry

frDteDynDlciDefsRowStatusEntry 1.3.6.1.4.1.562.2.4.1.101.5.1.1
A single entry in the table represents a single frDteDynDlciDefs component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteDynDlciDefsRowStatusEntry  

frDteDynDlciDefsRowStatus 1.3.6.1.4.1.562.2.4.1.101.5.1.1.1
This variable is used as the basis for SNMP naming of frDteDynDlciDefs components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

frDteDynDlciDefsComponentName 1.3.6.1.4.1.562.2.4.1.101.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frDteDynDlciDefsStorageType 1.3.6.1.4.1.562.2.4.1.101.5.1.1.4
This variable represents the storage type value for the frDteDynDlciDefs tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frDteDynDlciDefsIndex 1.3.6.1.4.1.562.2.4.1.101.5.1.1.10
This variable represents the index for the frDteDynDlciDefs tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frDteDynDlciDefsProvTable 1.3.6.1.4.1.562.2.4.1.101.5.10
This group contains the provisioned attributes for a virtual circuit. These attributes represent the default settings for the resulting Dlci components and can be operationally changed using the corresponding attributes under the Dlci component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteDynDlciDefsProvEntry

frDteDynDlciDefsProvEntry 1.3.6.1.4.1.562.2.4.1.101.5.10.1
An entry in the frDteDynDlciDefsProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteDynDlciDefsProvEntry  

frDteDynDlciDefsStdRowStatus 1.3.6.1.4.1.562.2.4.1.101.5.10.1.1
This attribute is used to manage the status of a StDlci component. Set to active to enable the StDlci component. Set to notInService to disable the StDlci component. Set to createAndGo (SNMP only) to create a new StDlci component. Set to destroy (SNMP only) to delete an existing StDlci component.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER active(1), notInService(2)  

frDteDynDlciDefsRateEnforcement 1.3.6.1.4.1.562.2.4.1.101.5.10.1.2
This attribute specifies whether the CIR attributes committedInformationRate, committedBurst, and excessBurst are used to define rate enforcement on this user DLCI. If rateEnforcement is enabled, and the combined Committed and Excess burst thresholds are exceeded, the frame in violation will be discarded immediately if a HibernationQueue subcomponent is not provisioned under the StDlci component. If a HibernationQueue is provisioned, the frame will be placed on the HibernationQueue at time of violation and transmission will be attempted later after the point at which the burst thresholds will no longer be exceeded. Setting all the CIR attributes to zero has the same affect as setting this attribute to disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

frDteDynDlciDefsCommittedInformationRate 1.3.6.1.4.1.562.2.4.1.101.5.10.1.3
The average number of bits to be transferred per second over the DLCI to the DCE. When this attribute is set to zero, the link speed will be used instead.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..48000000  

frDteDynDlciDefsCommittedBurst 1.3.6.1.4.1.562.2.4.1.101.5.10.1.4
The committed burst size (in bits) to which the DLCI wants to subscribe.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..2048000  

frDteDynDlciDefsExcessBurst 1.3.6.1.4.1.562.2.4.1.101.5.10.1.5
The excess burst size (in bits) to which the DLCI wants to subscribe.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..2048000  

frDteDynDlciDefsExcessBurstAction 1.3.6.1.4.1.562.2.4.1.101.5.10.1.6
This attribute specifies the action taken when the committedBurst size has been exceeded on the DLCI but the excessBurst size has not. If the attribute is set to setDeBit, the Discard Eligibility bit in the Frame Relay header will be turned on. If the attribute is set to none, no action will be taken.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), setDeBit(2)  

frDteDynDlciDefsIpCos 1.3.6.1.4.1.562.2.4.1.101.5.10.1.7
This attribute specifies the initial Class of Service (CoS) given to each packet received on the on the virtual circuit identified by the dlci. The CoS value n is used to select Vr/ QosP/n. which determines the QualityofService-Profile to be used when the packet is forwarded. The intial CoS given to a packet by the assignedQoS attribute may be overriden when the cosPolicyAssignment attribute is defined on the IpPort or Ip components. When a packet is to be transmitted on a frDte protocol port where multiple virtual circuits are available for the packet's next hop, the packet is forwarded using the dlci where the ipCos value matches the CoS of the packet. When the packets's CoS does not match the ipCos value of any of the available virtual circuits, the packet will be forwarded using next lowest CoS; failing this, the packet will be forwarded using the next highest CoS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..3  

frDteStDlci 1.3.6.1.4.1.562.2.4.1.101.6
OBJECT IDENTIFIER    

frDteStDlciRowStatusTable 1.3.6.1.4.1.562.2.4.1.101.6.1
This entry controls the addition and deletion of frDteStDlci components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteStDlciRowStatusEntry

frDteStDlciRowStatusEntry 1.3.6.1.4.1.562.2.4.1.101.6.1.1
A single entry in the table represents a single frDteStDlci component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteStDlciRowStatusEntry  

frDteStDlciRowStatus 1.3.6.1.4.1.562.2.4.1.101.6.1.1.1
This variable is used as the basis for SNMP naming of frDteStDlci components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frDteStDlciComponentName 1.3.6.1.4.1.562.2.4.1.101.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frDteStDlciStorageType 1.3.6.1.4.1.562.2.4.1.101.6.1.1.4
This variable represents the storage type value for the frDteStDlci tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frDteStDlciIndex 1.3.6.1.4.1.562.2.4.1.101.6.1.1.10
This variable represents the index for the frDteStDlci tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 16..1007  

frDteStDlciProvTable 1.3.6.1.4.1.562.2.4.1.101.6.10
This group contains the provisioned attributes for a virtual circuit. These attributes represent the default settings for the resulting Dlci components and can be operationally changed using the corresponding attributes under the Dlci component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteStDlciProvEntry

frDteStDlciProvEntry 1.3.6.1.4.1.562.2.4.1.101.6.10.1
An entry in the frDteStDlciProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteStDlciProvEntry  

frDteStDlciStdRowStatus 1.3.6.1.4.1.562.2.4.1.101.6.10.1.1
This attribute is used to manage the status of a StDlci component. Set to active to enable the StDlci component. Set to notInService to disable the StDlci component. Set to createAndGo (SNMP only) to create a new StDlci component. Set to destroy (SNMP only) to delete an existing StDlci component.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER active(1), notInService(2)  

frDteStDlciRateEnforcement 1.3.6.1.4.1.562.2.4.1.101.6.10.1.2
This attribute specifies whether the CIR attributes committedInformationRate, committedBurst, and excessBurst are used to define rate enforcement on this user DLCI. If rateEnforcement is enabled, and the combined Committed and Excess burst thresholds are exceeded, the frame in violation will be discarded immediately if a HibernationQueue subcomponent is not provisioned under the StDlci component. If a HibernationQueue is provisioned, the frame will be placed on the HibernationQueue at time of violation and transmission will be attempted later after the point at which the burst thresholds will no longer be exceeded. Setting all the CIR attributes to zero has the same affect as setting this attribute to disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

frDteStDlciCommittedInformationRate 1.3.6.1.4.1.562.2.4.1.101.6.10.1.3
The average number of bits to be transferred per second over the DLCI to the DCE. When this attribute is set to zero, the link speed will be used instead.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..48000000  

frDteStDlciCommittedBurst 1.3.6.1.4.1.562.2.4.1.101.6.10.1.4
The committed burst size (in bits) to which the DLCI wants to subscribe.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..2048000  

frDteStDlciExcessBurst 1.3.6.1.4.1.562.2.4.1.101.6.10.1.5
The excess burst size (in bits) to which the DLCI wants to subscribe.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..2048000  

frDteStDlciExcessBurstAction 1.3.6.1.4.1.562.2.4.1.101.6.10.1.6
This attribute specifies the action taken when the committedBurst size has been exceeded on the DLCI but the excessBurst size has not. If the attribute is set to setDeBit, the Discard Eligibility bit in the Frame Relay header will be turned on. If the attribute is set to none, no action will be taken.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), setDeBit(2)  

frDteStDlciIpCos 1.3.6.1.4.1.562.2.4.1.101.6.10.1.7
This attribute specifies the initial Class of Service (CoS) given to each packet received on the on the virtual circuit identified by the dlci. The CoS value n is used to select Vr/ QosP/n. which determines the QualityofService-Profile to be used when the packet is forwarded. The intial CoS given to a packet by the assignedQoS attribute may be overriden when the cosPolicyAssignment attribute is defined on the IpPort or Ip components. When a packet is to be transmitted on a frDte protocol port where multiple virtual circuits are available for the packet's next hop, the packet is forwarded using the dlci where the ipCos value matches the CoS of the packet. When the packets's CoS does not match the ipCos value of any of the available virtual circuits, the packet will be forwarded using next lowest CoS; failing this, the packet will be forwarded using the next highest CoS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..3  

frDteStDlciRgLinkTable 1.3.6.1.4.1.562.2.4.1.101.6.11
This group provides the link between a Dlci and a remoteGroup.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteStDlciRgLinkEntry

frDteStDlciRgLinkEntry 1.3.6.1.4.1.562.2.4.1.101.6.11.1
An entry in the frDteStDlciRgLinkTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteStDlciRgLinkEntry  

frDteStDlciLinkToRemoteGroup 1.3.6.1.4.1.562.2.4.1.101.6.11.1.1
This attribute associates a StDlci component with a Rg component. Provisioned StDlci components must be linked to a Rg component which is under the same FrDte component.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

frDteStDlciHq 1.3.6.1.4.1.562.2.4.1.101.6.2
OBJECT IDENTIFIER    

frDteStDlciHqRowStatusTable 1.3.6.1.4.1.562.2.4.1.101.6.2.1
This entry controls the addition and deletion of frDteStDlciHq components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteStDlciHqRowStatusEntry

frDteStDlciHqRowStatusEntry 1.3.6.1.4.1.562.2.4.1.101.6.2.1.1
A single entry in the table represents a single frDteStDlciHq component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteStDlciHqRowStatusEntry  

frDteStDlciHqRowStatus 1.3.6.1.4.1.562.2.4.1.101.6.2.1.1.1
This variable is used as the basis for SNMP naming of frDteStDlciHq components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frDteStDlciHqComponentName 1.3.6.1.4.1.562.2.4.1.101.6.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frDteStDlciHqStorageType 1.3.6.1.4.1.562.2.4.1.101.6.2.1.1.4
This variable represents the storage type value for the frDteStDlciHq tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frDteStDlciHqIndex 1.3.6.1.4.1.562.2.4.1.101.6.2.1.1.10
This variable represents the index for the frDteStDlciHq tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frDteStDlciHqProvTable 1.3.6.1.4.1.562.2.4.1.101.6.2.10
This group contains the Link Emission Queue provisioned attributes.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteStDlciHqProvEntry

frDteStDlciHqProvEntry 1.3.6.1.4.1.562.2.4.1.101.6.2.10.1
An entry in the frDteStDlciHqProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteStDlciHqProvEntry  

frDteStDlciHqMaxPackets 1.3.6.1.4.1.562.2.4.1.101.6.2.10.1.1
This attribute specifies the maximum number of packets allowed in the Leq before being discarded. If this attribute is set to zero then the maximum number of packets is calculated from the transmit data rate. This calculated value is placed in queuePktThreshold.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..2048  

frDteStDlciHqMaxMsecData 1.3.6.1.4.1.562.2.4.1.101.6.2.10.1.2
This attribute specifies the maximum number of 'Milliseconds worth of data' allowed in the Leq before packets are discarded. The queueByteThreshold will be calculated from this attribute, based on the transmit data rate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 100..60000  

frDteStDlciHqMaxPercentMulticast 1.3.6.1.4.1.562.2.4.1.101.6.2.10.1.3
This attribute specifies the maximum percentage of multicast packets allowed in the Leq, based on queuePktThreshold, before being discarded. The calculated value will be placed in queueMulticastThreshold.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..100  

frDteStDlciHqTimeToLive 1.3.6.1.4.1.562.2.4.1.101.6.2.10.1.4
This attribute specifies the 'Milliseconds Time To Live' of packets in the Leq. If the timeToLive of a packet expires, it will be discarded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 100..60000  

frDteStDlciHqStatsTable 1.3.6.1.4.1.562.2.4.1.101.6.2.11
This group contains HibernationQueue general statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteStDlciHqStatsEntry

frDteStDlciHqStatsEntry 1.3.6.1.4.1.562.2.4.1.101.6.2.11.1
An entry in the frDteStDlciHqStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteStDlciHqStatsEntry  

frDteStDlciHqTimedOutPkt 1.3.6.1.4.1.562.2.4.1.101.6.2.11.1.1
This attribute counts the number of packets that have been discarded due to exceeding the timeToLive. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteStDlciHqQueuePurgeDiscards 1.3.6.1.4.1.562.2.4.1.101.6.2.11.1.2
This attribute counts the total number of packets discarded by a queue purge which occurs when the Dlci goes down. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteStDlciHqTStatsTable 1.3.6.1.4.1.562.2.4.1.101.6.2.12
This group contains Link Emission Queue total statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteStDlciHqTStatsEntry

frDteStDlciHqTStatsEntry 1.3.6.1.4.1.562.2.4.1.101.6.2.12.1
An entry in the frDteStDlciHqTStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteStDlciHqTStatsEntry  

frDteStDlciHqTotalPktHandled 1.3.6.1.4.1.562.2.4.1.101.6.2.12.1.1
This attribute counts the total number of packets handled by the Leq. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteStDlciHqTotalPktForwarded 1.3.6.1.4.1.562.2.4.1.101.6.2.12.1.2
This attribute counts the total number of packets forwarded by the Leq. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteStDlciHqTotalPktQueued 1.3.6.1.4.1.562.2.4.1.101.6.2.12.1.3
This attribute counts the total number of packets that required queuing by the Leq due to transmit congestion. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteStDlciHqTotalMulticastPkt 1.3.6.1.4.1.562.2.4.1.101.6.2.12.1.4
This attribute counts the total number of multicast packets handled by this instance of FrDte. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteStDlciHqTotalPktDiscards 1.3.6.1.4.1.562.2.4.1.101.6.2.12.1.5
This attribute counts the total number of packets that were discarded for this instance of FrDte. This is the sum of timedOutPkt, forcedPktDiscards, queuePurgeDiscards, pktThresholdExceeded, byteThresholdExceeded, mulThresholdExceeded and memThresholdExceeded. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteStDlciHqCStatsTable 1.3.6.1.4.1.562.2.4.1.101.6.2.13
This group contains Link Emission Queue current statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteStDlciHqCStatsEntry

frDteStDlciHqCStatsEntry 1.3.6.1.4.1.562.2.4.1.101.6.2.13.1
An entry in the frDteStDlciHqCStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteStDlciHqCStatsEntry  

frDteStDlciHqCurrentPktQueued 1.3.6.1.4.1.562.2.4.1.101.6.2.13.1.1
This attribute contains the current number of packets queued.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..4294967295  

frDteStDlciHqCurrentBytesQueued 1.3.6.1.4.1.562.2.4.1.101.6.2.13.1.2
This attribute contains the current number of bytes queued.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..4294967295  

frDteStDlciHqCurrentMulticastQueued 1.3.6.1.4.1.562.2.4.1.101.6.2.13.1.3
This attribute counts the current number of multicast packets in the queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..4294967295  

frDteStDlciHqThrStatsTable 1.3.6.1.4.1.562.2.4.1.101.6.2.14
This group contains Link Emission Queue threshold statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteStDlciHqThrStatsEntry

frDteStDlciHqThrStatsEntry 1.3.6.1.4.1.562.2.4.1.101.6.2.14.1
An entry in the frDteStDlciHqThrStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteStDlciHqThrStatsEntry  

frDteStDlciHqQueuePktThreshold 1.3.6.1.4.1.562.2.4.1.101.6.2.14.1.1
This attribute is the maximum number of packets that can be contained in the queue before being discarded. If maxPackets was set to 0 then this attribute will contain the value that has been calculated based on the transmit data rate. If maxPackets was set to one or more than this attribute will contain that number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frDteStDlciHqPktThresholdExceeded 1.3.6.1.4.1.562.2.4.1.101.6.2.14.1.2
This attribute counts the number of packets discarded due to the queuePktThreshold being exceeded. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteStDlciHqQueueByteThreshold 1.3.6.1.4.1.562.2.4.1.101.6.2.14.1.3
This attribute is the maximum number of bytes allowed in the queue based on maxMsecData and the transmit data rate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frDteStDlciHqByteThresholdExceeded 1.3.6.1.4.1.562.2.4.1.101.6.2.14.1.4
This attribute counts the number of packets discarded due to the queueByteThreshold being exceeded. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteStDlciHqQueueMulticastThreshold 1.3.6.1.4.1.562.2.4.1.101.6.2.14.1.5
This attribute is the number of multicast packets allowed in the queue based on maxPercentMulticast and maxPackets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frDteStDlciHqMulThresholdExceeded 1.3.6.1.4.1.562.2.4.1.101.6.2.14.1.6
This attribute counts the number of packets discarded due to the queueMulticastThreshold being exceeded. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteStDlciHqMemThresholdExceeded 1.3.6.1.4.1.562.2.4.1.101.6.2.14.1.7
This attribute counts the number of packets discarded due to exceeding the memory usage threshold for Leq. The memory usage threshold is determined by the Leq software, guaranteeing that the Leq does not consume all of the memory. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteLeq 1.3.6.1.4.1.562.2.4.1.101.7
OBJECT IDENTIFIER    

frDteLeqRowStatusTable 1.3.6.1.4.1.562.2.4.1.101.7.1
This entry controls the addition and deletion of frDteLeq components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteLeqRowStatusEntry

frDteLeqRowStatusEntry 1.3.6.1.4.1.562.2.4.1.101.7.1.1
A single entry in the table represents a single frDteLeq component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteLeqRowStatusEntry  

frDteLeqRowStatus 1.3.6.1.4.1.562.2.4.1.101.7.1.1.1
This variable is used as the basis for SNMP naming of frDteLeq components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frDteLeqComponentName 1.3.6.1.4.1.562.2.4.1.101.7.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frDteLeqStorageType 1.3.6.1.4.1.562.2.4.1.101.7.1.1.4
This variable represents the storage type value for the frDteLeq tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frDteLeqIndex 1.3.6.1.4.1.562.2.4.1.101.7.1.1.10
This variable represents the index for the frDteLeq tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frDteLeqProvTable 1.3.6.1.4.1.562.2.4.1.101.7.10
This group contains the Link Emission Queue provisioned attributes.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteLeqProvEntry

frDteLeqProvEntry 1.3.6.1.4.1.562.2.4.1.101.7.10.1
An entry in the frDteLeqProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteLeqProvEntry  

frDteLeqMaxPackets 1.3.6.1.4.1.562.2.4.1.101.7.10.1.1
This attribute specifies the maximum number of packets allowed in the Leq before being discarded. If this attribute is set to zero then the maximum number of packets is calculated from the transmit data rate. This calculated value is placed in queuePktThreshold.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..2048  

frDteLeqMaxMsecData 1.3.6.1.4.1.562.2.4.1.101.7.10.1.2
This attribute specifies the maximum number of 'Milliseconds worth of data' allowed in the Leq before packets are discarded. The queueByteThreshold will be calculated from this attribute, based on the transmit data rate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 100..60000  

frDteLeqMaxPercentMulticast 1.3.6.1.4.1.562.2.4.1.101.7.10.1.3
This attribute specifies the maximum percentage of multicast packets allowed in the Leq, based on queuePktThreshold, before being discarded. The calculated value will be placed in queueMulticastThreshold.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..100  

frDteLeqTimeToLive 1.3.6.1.4.1.562.2.4.1.101.7.10.1.4
This attribute specifies the 'Milliseconds Time To Live' of packets in the Leq. If the timeToLive of a packet expires, it will be discarded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 100..60000  

frDteLeqStatsTable 1.3.6.1.4.1.562.2.4.1.101.7.11
This group contains Link Emission Queue general statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteLeqStatsEntry

frDteLeqStatsEntry 1.3.6.1.4.1.562.2.4.1.101.7.11.1
An entry in the frDteLeqStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteLeqStatsEntry  

frDteLeqTimedOutPkt 1.3.6.1.4.1.562.2.4.1.101.7.11.1.1
This attribute counts the number of packets that have been discarded due to exceeding the timeToLive. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteLeqHardwareForcedPkt 1.3.6.1.4.1.562.2.4.1.101.7.11.1.2
This attribute counts the number of hardware forced packets on this instance of FrDte. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteLeqForcedPktDiscards 1.3.6.1.4.1.562.2.4.1.101.7.11.1.3
This attribute counts the total number of hardware forced packets that had to be discarded due to link failure. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteLeqQueuePurgeDiscards 1.3.6.1.4.1.562.2.4.1.101.7.11.1.4
This attribute counts the total number of packets discarded by a queue purge (i.e. a discarding of all packets on the queue). This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteLeqTStatsTable 1.3.6.1.4.1.562.2.4.1.101.7.12
This group contains Link Emission Queue total statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteLeqTStatsEntry

frDteLeqTStatsEntry 1.3.6.1.4.1.562.2.4.1.101.7.12.1
An entry in the frDteLeqTStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteLeqTStatsEntry  

frDteLeqTotalPktHandled 1.3.6.1.4.1.562.2.4.1.101.7.12.1.1
This attribute counts the total number of packets handled by the Leq. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteLeqTotalPktForwarded 1.3.6.1.4.1.562.2.4.1.101.7.12.1.2
This attribute counts the total number of packets forwarded by the Leq. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteLeqTotalPktQueued 1.3.6.1.4.1.562.2.4.1.101.7.12.1.3
This attribute counts the total number of packets that required queuing by the Leq due to transmit congestion. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteLeqTotalMulticastPkt 1.3.6.1.4.1.562.2.4.1.101.7.12.1.4
This attribute counts the total number of multicast packets handled by this instance of FrDte. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteLeqTotalPktDiscards 1.3.6.1.4.1.562.2.4.1.101.7.12.1.5
This attribute counts the total number of packets that were discarded for this instance of FrDte. This is the sum of timedOutPkt, forcedPktDiscards, queuePurgeDiscards, pktThresholdExceeded, byteThresholdExceeded, mulThresholdExceeded and memThresholdExceeded. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteLeqCStatsTable 1.3.6.1.4.1.562.2.4.1.101.7.13
This group contains Link Emission Queue current statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteLeqCStatsEntry

frDteLeqCStatsEntry 1.3.6.1.4.1.562.2.4.1.101.7.13.1
An entry in the frDteLeqCStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteLeqCStatsEntry  

frDteLeqCurrentPktQueued 1.3.6.1.4.1.562.2.4.1.101.7.13.1.1
This attribute contains the current number of packets queued.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..4294967295  

frDteLeqCurrentBytesQueued 1.3.6.1.4.1.562.2.4.1.101.7.13.1.2
This attribute contains the current number of bytes queued.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..4294967295  

frDteLeqCurrentMulticastQueued 1.3.6.1.4.1.562.2.4.1.101.7.13.1.3
This attribute counts the current number of multicast packets in the queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..4294967295  

frDteLeqThrStatsTable 1.3.6.1.4.1.562.2.4.1.101.7.14
This group contains Link Emission Queue threshold statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteLeqThrStatsEntry

frDteLeqThrStatsEntry 1.3.6.1.4.1.562.2.4.1.101.7.14.1
An entry in the frDteLeqThrStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteLeqThrStatsEntry  

frDteLeqQueuePktThreshold 1.3.6.1.4.1.562.2.4.1.101.7.14.1.1
This attribute is the maximum number of packets that can be contained in the queue before being discarded. If maxPackets was set to 0 then this attribute will contain the value that has been calculated based on the transmit data rate. If maxPackets was set to one or more than this attribute will contain that number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frDteLeqPktThresholdExceeded 1.3.6.1.4.1.562.2.4.1.101.7.14.1.2
This attribute counts the number of packets discarded due to the queuePktThreshold being exceeded. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteLeqQueueByteThreshold 1.3.6.1.4.1.562.2.4.1.101.7.14.1.3
This attribute is the maximum number of bytes allowed in the queue based on maxMsecData and the transmit data rate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frDteLeqByteThresholdExceeded 1.3.6.1.4.1.562.2.4.1.101.7.14.1.4
This attribute counts the number of packets discarded due to the queueByteThreshold being exceeded. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteLeqQueueMulticastThreshold 1.3.6.1.4.1.562.2.4.1.101.7.14.1.5
This attribute is the number of multicast packets allowed in the queue based on maxPercentMulticast and maxPackets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frDteLeqMulThresholdExceeded 1.3.6.1.4.1.562.2.4.1.101.7.14.1.6
This attribute counts the number of packets discarded due to the queueMulticastThreshold being exceeded. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteLeqMemThresholdExceeded 1.3.6.1.4.1.562.2.4.1.101.7.14.1.7
This attribute counts the number of packets discarded due to exceeding the memory usage threshold for Leq. The memory usage threshold is determined by the Leq software, guaranteeing that the Leq does not consume all of the memory. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteDlci 1.3.6.1.4.1.562.2.4.1.101.8
OBJECT IDENTIFIER    

frDteDlciRowStatusTable 1.3.6.1.4.1.562.2.4.1.101.8.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of frDteDlci components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteDlciRowStatusEntry

frDteDlciRowStatusEntry 1.3.6.1.4.1.562.2.4.1.101.8.1.1
A single entry in the table represents a single frDteDlci component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteDlciRowStatusEntry  

frDteDlciRowStatus 1.3.6.1.4.1.562.2.4.1.101.8.1.1.1
This variable is used as the basis for SNMP naming of frDteDlci components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

frDteDlciComponentName 1.3.6.1.4.1.562.2.4.1.101.8.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frDteDlciStorageType 1.3.6.1.4.1.562.2.4.1.101.8.1.1.4
This variable represents the storage type value for the frDteDlci tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frDteDlciIndex 1.3.6.1.4.1.562.2.4.1.101.8.1.1.10
This variable represents the index for the frDteDlci tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 0..1023  

frDteDlciStateTable 1.3.6.1.4.1.562.2.4.1.101.8.10
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteDlciStateEntry

frDteDlciStateEntry 1.3.6.1.4.1.562.2.4.1.101.8.10.1
An entry in the frDteDlciStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteDlciStateEntry  

frDteDlciAdminState 1.3.6.1.4.1.562.2.4.1.101.8.10.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

frDteDlciOperationalState 1.3.6.1.4.1.562.2.4.1.101.8.10.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

frDteDlciUsageState 1.3.6.1.4.1.562.2.4.1.101.8.10.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

frDteDlciOperTable 1.3.6.1.4.1.562.2.4.1.101.8.11
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the operational attributes for the Dlci component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteDlciOperEntry

frDteDlciOperEntry 1.3.6.1.4.1.562.2.4.1.101.8.11.1
An entry in the frDteDlciOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteDlciOperEntry  

frDteDlciDlciState 1.3.6.1.4.1.562.2.4.1.101.8.11.1.4
This attribute reflects the current operational circuit state of the Dlci. The state active indicates that the circuit is up and inactive that the circuit is down. The state invalid means the circuit has been deleted by the DCE (via Lmi).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), active(2), inactive(3)  

frDteDlciLastTimeChange 1.3.6.1.4.1.562.2.4.1.101.8.11.1.5
The last time dlciState changed state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  EnterpriseDateAndTime Size(0|19)  

frDteDlciSentFrames 1.3.6.1.4.1.562.2.4.1.101.8.11.1.7
Number of frames transmitted across the interface. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteDlciSentOctets 1.3.6.1.4.1.562.2.4.1.101.8.11.1.8
The number of octets sent from this virtual circuit since it was created. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteDlciReceivedFrames 1.3.6.1.4.1.562.2.4.1.101.8.11.1.9
Number of frames received across the interface. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteDlciReceivedOctets 1.3.6.1.4.1.562.2.4.1.101.8.11.1.10
The number of octets sent from this virtual circuit since it was created. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteDlciReceivedFECNs 1.3.6.1.4.1.562.2.4.1.101.8.11.1.11
Number of frames with the FECN bit set received from the network. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteDlciReceivedBECNs 1.3.6.1.4.1.562.2.4.1.101.8.11.1.12
Number of frames with the BECN bit set received from the network. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteDlciDiscardedFrames 1.3.6.1.4.1.562.2.4.1.101.8.11.1.13
The number of inbound frames dropped because of format errors, or because the VC was inactive. This counter will wrap around to 0 when it exceeds its maximum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frDteDlciCreationType 1.3.6.1.4.1.562.2.4.1.101.8.11.1.14
This indicates whether the virtual circuit was manually created (static), or dynamically created (dynamic) via the data link control management interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

frDteDlciCreationTime 1.3.6.1.4.1.562.2.4.1.101.8.11.1.15
The time when the circuit was created, whether by the Data Link Connection Management Interface or by an SNMP set request.
Status: mandatory Access: read-only
OBJECT-TYPE    
  EnterpriseDateAndTime Size(0|19)  

frDteDlciRateEnforcement 1.3.6.1.4.1.562.2.4.1.101.8.11.1.17
This attribute specifies whether the CIR attributes committedInformationRate, committedBurst, and excessBurst are used to define rate enforcement on this user DLCI. If rateEnforcement is enabled, and the combined Committed and Excess burst thresholds are exceeded, the frame in violation will be discarded immediately if a HibernationQueue subcomponent is not provisioned under the StDlci component (static entries only). If a HibernationQueue is provisioned, the frame will be placed on the HibernationQueue at time of violation and transmission will be attempted later after the point at which the burst thresholds will no longer be exceeded. Setting all the CIR attributes to zero has the same affect as setting this attribute to disabled. Setting this attribute will operationally override the corresponding provisional value on static entries.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

frDteDlciCommittedInformationRate 1.3.6.1.4.1.562.2.4.1.101.8.11.1.18
The average number of bits to be transferred per second over the DLCI to the DCE. When this attribute is set to zero, the link speed will be used instead. Setting this attribute will operationally override the corresponding provisional value on static entries.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge32 0..48000000  

frDteDlciCommittedBurst 1.3.6.1.4.1.562.2.4.1.101.8.11.1.19
The committed burst size (in bits) to which the DLCI wants to subscribe. Setting this attribute will operationally override the corresponding provisional value on static entries.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..2048000  

frDteDlciExcessBurst 1.3.6.1.4.1.562.2.4.1.101.8.11.1.20
The excess burst size (in bits) to which the DLCI wants to subscribe. Setting this attribute will operationally override the corresponding provisional value on static entries.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..2048000  

frDteDlciExcessBurstAction 1.3.6.1.4.1.562.2.4.1.101.8.11.1.21
This attribute specifies the action taken when the committedBurst size has been exceeded on the Dlci but the excessBurst size has not. If the attribute is set to setDeBit, the Discard Eligibility bit in the Frame Relay header will be turned on. If the attribute is set to none, no action will be taken. Setting this attribute will operationally override the corresponding provisional value on static entries.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), setDeBit(2)  

frDteVFramer 1.3.6.1.4.1.562.2.4.1.101.9
OBJECT IDENTIFIER    

frDteVFramerRowStatusTable 1.3.6.1.4.1.562.2.4.1.101.9.1
This entry controls the addition and deletion of frDteVFramer components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteVFramerRowStatusEntry

frDteVFramerRowStatusEntry 1.3.6.1.4.1.562.2.4.1.101.9.1.1
A single entry in the table represents a single frDteVFramer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteVFramerRowStatusEntry  

frDteVFramerRowStatus 1.3.6.1.4.1.562.2.4.1.101.9.1.1.1
This variable is used as the basis for SNMP naming of frDteVFramer components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frDteVFramerComponentName 1.3.6.1.4.1.562.2.4.1.101.9.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frDteVFramerStorageType 1.3.6.1.4.1.562.2.4.1.101.9.1.1.4
This variable represents the storage type value for the frDteVFramer tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frDteVFramerIndex 1.3.6.1.4.1.562.2.4.1.101.9.1.1.10
This variable represents the index for the frDteVFramer tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frDteVFramerProvTable 1.3.6.1.4.1.562.2.4.1.101.9.10
This group contains provisionable attributes for the VirtualFramer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteVFramerProvEntry

frDteVFramerProvEntry 1.3.6.1.4.1.562.2.4.1.101.9.10.1
An entry in the frDteVFramerProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteVFramerProvEntry  

frDteVFramerOtherVirtualFramer 1.3.6.1.4.1.562.2.4.1.101.9.10.1.1
This attribute specifies the other VirtualFramer to which the service is linked, for example, FrUni/n VirtualFramer, FrDte/n VirtualFramer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

frDteVFramerLogicalProcessor 1.3.6.1.4.1.562.2.4.1.101.9.10.1.2
This attribute specifies the logical processor on which the service component will reside.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

frDteVFramerStateTable 1.3.6.1.4.1.562.2.4.1.101.9.11
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteVFramerStateEntry

frDteVFramerStateEntry 1.3.6.1.4.1.562.2.4.1.101.9.11.1
An entry in the frDteVFramerStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteVFramerStateEntry  

frDteVFramerAdminState 1.3.6.1.4.1.562.2.4.1.101.9.11.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

frDteVFramerOperationalState 1.3.6.1.4.1.562.2.4.1.101.9.11.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

frDteVFramerUsageState 1.3.6.1.4.1.562.2.4.1.101.9.11.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

frDteVFramerStatsTable 1.3.6.1.4.1.562.2.4.1.101.9.12
This group contains the operational statistics data for a VirtualFramer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDteVFramerStatsEntry

frDteVFramerStatsEntry 1.3.6.1.4.1.562.2.4.1.101.9.12.1
An entry in the frDteVFramerStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDteVFramerStatsEntry  

frDteVFramerFrmToOtherVFramer 1.3.6.1.4.1.562.2.4.1.101.9.12.1.2
This attribute counts the frames transmitted to the otherVirtualFramer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

frDteVFramerFrmFromOtherVFramer 1.3.6.1.4.1.562.2.4.1.101.9.12.1.3
This attribute counts the frames received from the otherVirtualFramer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

frDteVFramerOctetFromOtherVFramer 1.3.6.1.4.1.562.2.4.1.101.9.12.1.5
This attribute counts the octets received from the otherVirtualFramer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

frameRelayDteGroup 1.3.6.1.4.1.562.2.4.2.32.1
OBJECT IDENTIFIER    

frameRelayDteGroupBE 1.3.6.1.4.1.562.2.4.2.32.1.5
OBJECT IDENTIFIER    

frameRelayDteGroupBE00 1.3.6.1.4.1.562.2.4.2.32.1.5.1
OBJECT IDENTIFIER    

frameRelayDteGroupBE00A 1.3.6.1.4.1.562.2.4.2.32.1.5.1.2
OBJECT IDENTIFIER    

frameRelayDteCapabilities 1.3.6.1.4.1.562.2.4.2.32.3
OBJECT IDENTIFIER    

frameRelayDteCapabilitiesBE 1.3.6.1.4.1.562.2.4.2.32.3.5
OBJECT IDENTIFIER    

frameRelayDteCapabilitiesBE00 1.3.6.1.4.1.562.2.4.2.32.3.5.1
OBJECT IDENTIFIER    

frameRelayDteCapabilitiesBE00A 1.3.6.1.4.1.562.2.4.2.32.3.5.1.2
OBJECT IDENTIFIER