Nortel-Magellan-Passport-FrameRelayUniMIB

File: Nortel-Magellan-Passport-FrameRelayUniMIB.mib (354535 bytes)

Imported modules

RFC-1212 Nortel-Magellan-Passport-UsefulDefinitionsMIB Nortel-Magellan-Passport-StandardTextualConventionsMIB
Nortel-Magellan-Passport-TextualConventionsMIB

Imported symbols

OBJECT-TYPE components passportMIBs
Counter32 RowPointer DisplayString
StorageType RowStatus PassportCounter64
InterfaceIndex Gauge32 Integer32
Unsigned32 AsciiString Hex
NonReplicated FixedPoint3 HexString
EnterpriseDateAndTime Link DigitString
Unsigned64

Defined Types

FrUniRowStatusEntry  
SEQUENCE    
  frUniRowStatus RowStatus
  frUniComponentName DisplayString
  frUniStorageType StorageType
  frUniIndex Integer32

FrUniCidDataEntry  
SEQUENCE    
  frUniCustomerIdentifier Unsigned32

FrUniStateEntry  
SEQUENCE    
  frUniAdminState INTEGER
  frUniOperationalState INTEGER
  frUniUsageState INTEGER
  frUniAvailabilityStatus OCTET STRING
  frUniProceduralStatus OCTET STRING
  frUniControlStatus OCTET STRING
  frUniAlarmStatus OCTET STRING
  frUniStandbyStatus INTEGER
  frUniUnknownStatus INTEGER

FrUniStatsEntry  
SEQUENCE    
  frUniLastUnknownDlci Unsigned32
  frUniUnknownDlciFramesFromIf Counter32
  frUniInvalidHeaderFramesFromIf Counter32

FrUniIfEntryEntry  
SEQUENCE    
  frUniIfAdminStatus INTEGER
  frUniIfIndex InterfaceIndex

FrUniOperStatusEntry  
SEQUENCE    
  frUniSnmpOperStatus INTEGER

FrUniEmissionPriorityQsEntry  
SEQUENCE    
  frUniNumberOfEmissionQs Unsigned32

FrUniFrmToIfByQueueEntry  
SEQUENCE    
  frUniFrmToIfByQueueIndex Integer32
  frUniFrmToIfByQueueValue Unsigned32

FrUniOctetToIfByQueueEntry  
SEQUENCE    
  frUniOctetToIfByQueueIndex Integer32
  frUniOctetToIfByQueueValue Unsigned32

FrUniDnaRowStatusEntry  
SEQUENCE    
  frUniDnaRowStatus RowStatus
  frUniDnaComponentName DisplayString
  frUniDnaStorageType StorageType
  frUniDnaIndex NonReplicated

FrUniDnaAddressEntry  
SEQUENCE    
  frUniDnaNumberingPlanIndicator INTEGER
  frUniDnaDataNetworkAddress DigitString

FrUniDnaOutgoingOptionsEntry  
SEQUENCE    
  frUniDnaOutDefaultPriority INTEGER
  frUniDnaOutDefaultPathSensitivity INTEGER
  frUniDnaOutPathSensitivityOverRide INTEGER
  frUniDnaOutDefaultPathReliability INTEGER
  frUniDnaOutAccess INTEGER
  frUniDnaDefaultTransferPriority INTEGER
  frUniDnaTransferPriorityOverRide INTEGER

FrUniDnaIncomingOptionsEntry  
SEQUENCE    
  frUniDnaIncAccess INTEGER

FrUniDnaCallOptionsEntry  
SEQUENCE    
  frUniDnaAccountClass Unsigned32
  frUniDnaAccountCollection OCTET STRING
  frUniDnaServiceExchange Unsigned32
  frUniDnaEgressAccounting INTEGER
  frUniDnaDataPath INTEGER

FrUniDnaCugRowStatusEntry  
SEQUENCE    
  frUniDnaCugRowStatus RowStatus
  frUniDnaCugComponentName DisplayString
  frUniDnaCugStorageType StorageType
  frUniDnaCugIndex Integer32

FrUniDnaCugCugOptionsEntry  
SEQUENCE    
  frUniDnaCugType INTEGER
  frUniDnaCugDnic DigitString
  frUniDnaCugInterlockCode Unsigned32
  frUniDnaCugPreferential INTEGER
  frUniDnaCugOutCalls INTEGER
  frUniDnaCugIncCalls INTEGER

FrUniDnaHgMRowStatusEntry  
SEQUENCE    
  frUniDnaHgMRowStatus RowStatus
  frUniDnaHgMComponentName DisplayString
  frUniDnaHgMStorageType StorageType
  frUniDnaHgMIndex NonReplicated

FrUniDnaHgMIfEntry  
SEQUENCE    
  frUniDnaHgMAvailabilityUpdateThreshold Unsigned32

FrUniDnaHgMOpEntry  
SEQUENCE    
  frUniDnaHgMMaximumAvailableAggregateCir Unsigned32
  frUniDnaHgMAvailableAggregateCir Unsigned32
  frUniDnaHgMAvailabilityDelta INTEGER
  frUniDnaHgMAvailableDlcis Unsigned32

FrUniDnaHgMHgAddrRowStatusEntry  
SEQUENCE    
  frUniDnaHgMHgAddrRowStatus RowStatus
  frUniDnaHgMHgAddrComponentName DisplayString
  frUniDnaHgMHgAddrStorageType StorageType
  frUniDnaHgMHgAddrIndex Integer32

FrUniDnaHgMHgAddrAddrEntry  
SEQUENCE    
  frUniDnaHgMHgAddrNumberingPlanIndicator INTEGER
  frUniDnaHgMHgAddrDataNetworkAddress DigitString

FrUniFramerRowStatusEntry  
SEQUENCE    
  frUniFramerRowStatus RowStatus
  frUniFramerComponentName DisplayString
  frUniFramerStorageType StorageType
  frUniFramerIndex NonReplicated

FrUniFramerProvEntry  
SEQUENCE    
  frUniFramerInterfaceName Link

FrUniFramerLinkEntry  
SEQUENCE    
  frUniFramerFlagsBetweenFrames Unsigned32

FrUniFramerStateEntry  
SEQUENCE    
  frUniFramerAdminState INTEGER
  frUniFramerOperationalState INTEGER
  frUniFramerUsageState INTEGER

FrUniFramerStatsEntry  
SEQUENCE    
  frUniFramerFrmToIf Counter32
  frUniFramerFrmFromIf Counter32
  frUniFramerOctetFromIf Counter32
  frUniFramerAborts Counter32
  frUniFramerCrcErrors Counter32
  frUniFramerLrcErrors Counter32
  frUniFramerNonOctetErrors Counter32
  frUniFramerOverruns Counter32
  frUniFramerUnderruns Counter32
  frUniFramerLargeFrmErrors Counter32
  frUniFramerFrmModeErrors Counter32

FrUniFramerUtilEntry  
SEQUENCE    
  frUniFramerNormPrioLinkUtilToIf Gauge32
  frUniFramerNormPrioLinkUtilFromIf Gauge32

FrUniLmiRowStatusEntry  
SEQUENCE    
  frUniLmiRowStatus RowStatus
  frUniLmiComponentName DisplayString
  frUniLmiStorageType StorageType
  frUniLmiIndex NonReplicated

FrUniLmiParmsEntry  
SEQUENCE    
  frUniLmiProcedures INTEGER
  frUniLmiAsyncStatusReport INTEGER
  frUniLmiErrorEventThreshold Unsigned32
  frUniLmiEventCount Unsigned32
  frUniLmiCheckPointTimer Unsigned32
  frUniLmiMessageCountTimer Unsigned32
  frUniLmiIgnoreActiveBit INTEGER
  frUniLmiSide INTEGER
  frUniLmiPvcConfigParmsInFsr INTEGER

FrUniLmiStateEntry  
SEQUENCE    
  frUniLmiAdminState INTEGER
  frUniLmiOperationalState INTEGER
  frUniLmiUsageState INTEGER

FrUniLmiPsiEntry  
SEQUENCE    
  frUniLmiProtocolStatus INTEGER
  frUniLmiOpProcedures INTEGER

FrUniLmiStatsEntry  
SEQUENCE    
  frUniLmiKeepAliveStatusToIf Counter32
  frUniLmiFullStatusToIf Counter32
  frUniLmiKeepAliveStatusEnqFromIf Counter32
  frUniLmiFullStatusEnqFromIf Counter32
  frUniLmiNetworkSideEventHistory AsciiString
  frUniLmiProtocolErrors Counter32
  frUniLmiUnexpectedIes Counter32
  frUniLmiSequenceErrors Counter32
  frUniLmiUnexpectedReports Counter32
  frUniLmiPollingVerifTimeouts Counter32
  frUniLmiKeepAliveEnqToIf Counter32
  frUniLmiFullStatusEnqToIf Counter32
  frUniLmiUserSideEventHistory AsciiString
  frUniLmiStatusSequenceErrors Counter32
  frUniLmiNoStatusReportCount Counter32

FrUniLmiUspParmsEntry  
SEQUENCE    
  frUniLmiFullStatusPollingCycles Unsigned32
  frUniLmiLinkVerificationTimer Unsigned32

FrUniDlciRowStatusEntry  
SEQUENCE    
  frUniDlciRowStatus RowStatus
  frUniDlciComponentName DisplayString
  frUniDlciStorageType StorageType
  frUniDlciIndex Integer32

FrUniDlciStateEntry  
SEQUENCE    
  frUniDlciAdminState INTEGER
  frUniDlciOperationalState INTEGER
  frUniDlciUsageState INTEGER
  frUniDlciAvailabilityStatus OCTET STRING
  frUniDlciProceduralStatus OCTET STRING
  frUniDlciControlStatus OCTET STRING
  frUniDlciAlarmStatus OCTET STRING
  frUniDlciStandbyStatus INTEGER
  frUniDlciUnknownStatus INTEGER

FrUniDlciAbitEntry  
SEQUENCE    
  frUniDlciABitStatusToIf INTEGER
  frUniDlciABitReasonToIf INTEGER
  frUniDlciABitStatusFromIf INTEGER
  frUniDlciABitReasonFromIf INTEGER
  frUniDlciLoopbackState INTEGER

FrUniDlciCalldEntry  
SEQUENCE    
  frUniDlciCallType INTEGER
  frUniDlciQ933CallState INTEGER
  frUniDlciQ933CallReference Unsigned32

FrUniDlciSpOpEntry  
SEQUENCE    
  frUniDlciMaximumFrameSize Unsigned32
  frUniDlciRateEnforcement INTEGER
  frUniDlciCommittedInformationRate Unsigned32
  frUniDlciCommittedBurstSize Unsigned32
  frUniDlciExcessBurstSize Unsigned32
  frUniDlciMeasurementInterval Unsigned32
  frUniDlciRateAdaptation INTEGER
  frUniDlciAccounting INTEGER
  frUniDlciEmissionPriorityToIf INTEGER
  frUniDlciTransferPriToNwk Unsigned32
  frUniDlciTransferPriFromNwk Unsigned32

FrUniDlciStatsEntry  
SEQUENCE    
  frUniDlciFrmToIf Unsigned32
  frUniDlciFecnFrmToIf Unsigned32
  frUniDlciBecnFrmToIf Unsigned32
  frUniDlciBciToSubnet Unsigned32
  frUniDlciDeFrmToIf Unsigned32
  frUniDlciDiscCongestedToIf Unsigned32
  frUniDlciDiscDeCongestedToIf Unsigned32
  frUniDlciFrmFromIf Unsigned32
  frUniDlciFecnFrmFromIf Unsigned32
  frUniDlciBecnFrmFromIf Unsigned32
  frUniDlciFciFromSubnet Unsigned32
  frUniDlciBciFromSubnet Unsigned32
  frUniDlciDeFrmFromIf Unsigned32
  frUniDlciExcessFrmFromIf Unsigned32
  frUniDlciDiscExcessFromIf Unsigned32
  frUniDlciDiscFrameAbit Unsigned32
  frUniDlciDiscCongestedFromIf Unsigned32
  frUniDlciDiscDeCongestedFromIf Unsigned32
  frUniDlciErrorShortFrmFromIf Unsigned32
  frUniDlciErrorLongFrmFromIf Unsigned32
  frUniDlciBecnFrmSetByService Unsigned32
  frUniDlciBytesToIf Unsigned32
  frUniDlciDeBytesToIf Unsigned32
  frUniDlciDiscCongestedToIfBytes Unsigned32
  frUniDlciDiscDeCongestedToIfBytes Unsigned32
  frUniDlciBytesFromIf Unsigned32
  frUniDlciDeBytesFromIf Unsigned32
  frUniDlciExcessBytesFromIf Unsigned32
  frUniDlciDiscExcessFromIfBytes Unsigned32
  frUniDlciDiscByteAbit Unsigned32
  frUniDlciDiscCongestedFromIfBytes Unsigned32
  frUniDlciDiscDeCongestedFromIfBytes Unsigned32
  frUniDlciErrorShortBytesFromIf Unsigned32
  frUniDlciErrorLongBytesFromIf Unsigned32
  frUniDlciRateAdaptReduct Unsigned32
  frUniDlciRateAdaptReductPeriod Unsigned32
  frUniDlciTransferPriorityToNetwork INTEGER
  frUniDlciTransferPriorityFromNetwork INTEGER
  frUniDlciCirPresent Unsigned32
  frUniDlciEirPresent Unsigned32

FrUniDlciIntEntry  
SEQUENCE    
  frUniDlciStartTime EnterpriseDateAndTime
  frUniDlciTotalIngressBytes Unsigned64
  frUniDlciTotalEgressBytes Unsigned64
  frUniDlciEirIngressBytes Unsigned64
  frUniDlciEirEgressBytes Unsigned64
  frUniDlciDiscardedBytes Unsigned64
  frUniDlciTotalIngressSegFrm Unsigned32
  frUniDlciTotalEgressSegFrm Unsigned32
  frUniDlciEirIngressSegFrm Unsigned32
  frUniDlciEirEgressSegFrm Unsigned32
  frUniDlciDiscardedSegFrm Unsigned32
  frUniDlciCirPresentObs Unsigned32
  frUniDlciEirPresentObs Unsigned32
  frUniDlciRateEnforcementPresent INTEGER
  frUniDlciRateAdaptationPresent INTEGER
  frUniDlciLocalRateAdaptOccurred Unsigned32
  frUniDlciCallReferenceNumber Unsigned32
  frUniDlciElapsedDifference Unsigned32

FrUniDlciDcRowStatusEntry  
SEQUENCE    
  frUniDlciDcRowStatus RowStatus
  frUniDlciDcComponentName DisplayString
  frUniDlciDcStorageType StorageType
  frUniDlciDcIndex NonReplicated

FrUniDlciDcOptionsEntry  
SEQUENCE    
  frUniDlciDcRemoteNpi INTEGER
  frUniDlciDcRemoteDna DigitString
  frUniDlciDcRemoteDlci Unsigned32
  frUniDlciDcType INTEGER
  frUniDlciDcTransferPriority INTEGER
  frUniDlciDcDiscardPriority INTEGER
  frUniDlciDcDeDiscardPriority INTEGER
  frUniDlciDcDataPath INTEGER
  frUniDlciDcCugIndex Unsigned32
  frUniDlciDcCugType INTEGER

FrUniDlciDcNfaEntry  
SEQUENCE    
  frUniDlciDcNfaIndex Integer32
  frUniDlciDcNfaValue HexString
  frUniDlciDcNfaRowStatus RowStatus

FrUniDlciVcRowStatusEntry  
SEQUENCE    
  frUniDlciVcRowStatus RowStatus
  frUniDlciVcComponentName DisplayString
  frUniDlciVcStorageType StorageType
  frUniDlciVcIndex NonReplicated

FrUniDlciVcCadEntry  
SEQUENCE    
  frUniDlciVcType INTEGER
  frUniDlciVcState INTEGER
  frUniDlciVcPreviousState INTEGER
  frUniDlciVcDiagnosticCode Unsigned32
  frUniDlciVcPreviousDiagnosticCode Unsigned32
  frUniDlciVcCalledNpi INTEGER
  frUniDlciVcCalledDna DigitString
  frUniDlciVcCalledLcn Unsigned32
  frUniDlciVcCallingNpi INTEGER
  frUniDlciVcCallingDna DigitString
  frUniDlciVcCallingLcn Unsigned32
  frUniDlciVcAccountingEnabled INTEGER
  frUniDlciVcFastSelectCall INTEGER
  frUniDlciVcPathReliability INTEGER
  frUniDlciVcAccountingEnd INTEGER
  frUniDlciVcPriority INTEGER
  frUniDlciVcSegmentSize Unsigned32
  frUniDlciVcMaxSubnetPktSize Unsigned32
  frUniDlciVcRcosToNetwork INTEGER
  frUniDlciVcRcosFromNetwork INTEGER
  frUniDlciVcEmissionPriorityToNetwork INTEGER
  frUniDlciVcEmissionPriorityFromNetwork INTEGER
  frUniDlciVcDataPath AsciiString

FrUniDlciVcIntdEntry  
SEQUENCE    
  frUniDlciVcCallReferenceNumber Hex
  frUniDlciVcElapsedTimeTillNow Unsigned32
  frUniDlciVcSegmentsRx Unsigned32
  frUniDlciVcSegmentsSent Unsigned32
  frUniDlciVcStartTime EnterpriseDateAndTime

FrUniDlciVcFrdEntry  
SEQUENCE    
  frUniDlciVcFrmCongestedToSubnet Unsigned32
  frUniDlciVcCannotForwardToSubnet Unsigned32
  frUniDlciVcNotDataXferToSubnet Unsigned32
  frUniDlciVcOutOfRangeFrmFromSubnet Unsigned32
  frUniDlciVcCombErrorsFromSubnet Unsigned32
  frUniDlciVcDuplicatesFromSubnet Unsigned32
  frUniDlciVcNotDataXferFromSubnet Unsigned32
  frUniDlciVcFrmLossTimeouts Unsigned32
  frUniDlciVcOoSeqByteCntExceeded Unsigned32
  frUniDlciVcPeakOoSeqPktCount Unsigned32
  frUniDlciVcPeakOoSeqFrmForwarded Unsigned32
  frUniDlciVcSendSequenceNumber Unsigned32
  frUniDlciVcPktRetryTimeouts Unsigned32
  frUniDlciVcPeakRetryQueueSize Unsigned32
  frUniDlciVcSubnetRecoveries Unsigned32
  frUniDlciVcOoSeqPktCntExceeded Unsigned32
  frUniDlciVcPeakOoSeqByteCount Unsigned32

FrUniDlciVcDmepEntry  
SEQUENCE    
  frUniDlciVcDmepValue RowPointer

FrUniDlciSpRowStatusEntry  
SEQUENCE    
  frUniDlciSpRowStatus RowStatus
  frUniDlciSpComponentName DisplayString
  frUniDlciSpStorageType StorageType
  frUniDlciSpIndex NonReplicated

FrUniDlciSpParmsEntry  
SEQUENCE    
  frUniDlciSpMaximumFrameSize Unsigned32
  frUniDlciSpRateEnforcement INTEGER
  frUniDlciSpCommittedInformationRate Gauge32
  frUniDlciSpCommittedBurstSize Gauge32
  frUniDlciSpExcessBurstSize Gauge32
  frUniDlciSpMeasurementInterval Unsigned32
  frUniDlciSpRateAdaptation INTEGER
  frUniDlciSpAccounting INTEGER
  frUniDlciSpRaSensitivity Unsigned32
  frUniDlciSpUpdateBCI INTEGER

FrUniDlciLbRowStatusEntry  
SEQUENCE    
  frUniDlciLbRowStatus RowStatus
  frUniDlciLbComponentName DisplayString
  frUniDlciLbStorageType StorageType
  frUniDlciLbIndex NonReplicated

FrUniDlciLbStatsEntry  
SEQUENCE    
  frUniDlciLbLocalTotalFrm Unsigned32
  frUniDlciLbLocalTotalBytes Unsigned32
  frUniDlciLbLocalFecnFrm Unsigned32
  frUniDlciLbLocalBecnFrm Unsigned32
  frUniDlciLbLocalDeFrm Unsigned32
  frUniDlciLbLocalDeBytes Unsigned32
  frUniDlciLbRemoteTotalFrm Unsigned32
  frUniDlciLbRemoteTotalBytes Unsigned32
  frUniDlciLbRemoteFecnFrm Unsigned32
  frUniDlciLbRemoteBecnFrm Unsigned32
  frUniDlciLbRemoteDeFrm Unsigned32
  frUniDlciLbRemoteDeBytes Unsigned32

FrUniSigRowStatusEntry  
SEQUENCE    
  frUniSigRowStatus RowStatus
  frUniSigComponentName DisplayString
  frUniSigStorageType StorageType
  frUniSigIndex NonReplicated

FrUniSigRangeEntry  
SEQUENCE    
  frUniSigHighestPvcDlci Unsigned32

FrUniSigServParmsEntry  
SEQUENCE    
  frUniSigMaximumAggregateSvcCir Unsigned32
  frUniSigMaximumAggregateSvcEir Unsigned32
  frUniSigMaximumFrameSize Unsigned32
  frUniSigDefaultMaximumFrameSize Unsigned32
  frUniSigDefaultCommittedInformationRate Unsigned32
  frUniSigDefaultCommittedBurstSize Unsigned32
  frUniSigDefaultExcessBurstSize Unsigned32
  frUniSigUnlimitedAggregateEir INTEGER
  frUniSigRateEnforcement INTEGER
  frUniSigRateAdaptation INTEGER
  frUniSigMaximumAggregateSvcCirNormalQ Unsigned32
  frUniSigMaximumAggregateSvcCirHighQ Unsigned32
  frUniSigMaximumAggregateSvcCirInterruptQ Unsigned32
  frUniSigMaximumAggregateSvcEirNormalQ Unsigned32
  frUniSigMaximumAggregateSvcEirHighQ Unsigned32
  frUniSigMaximumAggregateSvcEirInterruptQ Unsigned32
  frUniSigX213IeHandling INTEGER
  frUniSigRaSensitivity Unsigned32
  frUniSigUpdateBCI INTEGER
  frUniSigDefaultLocCheck INTEGER

FrUniSigSysParmsEntry  
SEQUENCE    
  frUniSigCallSetupTimer Unsigned32
  frUniSigDisconnectTimer Unsigned32
  frUniSigReleaseTimer Unsigned32
  frUniSigCallProceedingTimer Unsigned32
  frUniSigNetworkType INTEGER

FrUniSigLapfSysEntry  
SEQUENCE    
  frUniSigWindowSize Unsigned32
  frUniSigRetransmitLimit Unsigned32
  frUniSigAckTimer Unsigned32
  frUniSigAckDelayTimer Unsigned32
  frUniSigIdleProbeTimer Unsigned32

FrUniSigStateEntry  
SEQUENCE    
  frUniSigAdminState INTEGER
  frUniSigOperationalState INTEGER
  frUniSigUsageState INTEGER

FrUniSigStatsEntry  
SEQUENCE    
  frUniSigCurrentNumberOfSvcCalls Unsigned32
  frUniSigInCalls Counter32
  frUniSigInCallsRefused Counter32
  frUniSigOutCalls Counter32
  frUniSigOutCallsFailed Counter32
  frUniSigProtocolErrors Counter32
  frUniSigQualityOfServiceNotAvailable Counter32
  frUniSigSetupTimeout Counter32
  frUniSigLastCauseInStatusMsgReceived Unsigned32
  frUniSigLastStateInStatusMsgReceived INTEGER
  frUniSigLastDlciReceivedStatus Unsigned32
  frUniSigLastQ933StateReceivedStatus INTEGER
  frUniSigLastTimeMsgBlockCongested EnterpriseDateAndTime
  frUniSigLastDlciWithMsgBlockCongestion Unsigned32
  frUniSigCurrentAggregateSvcCirNormalQ Unsigned32
  frUniSigCurrentAggregateSvcCirHighQ Unsigned32
  frUniSigCurrentAggregateSvcCirInterruptQ Unsigned32
  frUniSigCurrentAggregateSvcEirNormalQ Unsigned32
  frUniSigCurrentAggregateSvcEirHighQ Unsigned32
  frUniSigCurrentAggregateSvcEirInterruptQ Unsigned32

FrUniSigLapfStatusEntry  
SEQUENCE    
  frUniSigCurrentState INTEGER
  frUniSigLastStateChangeReason INTEGER
  frUniSigFrmrReceive HexString
  frUniSigCurrentQueueSize Counter32

FrUniSigLapfStatsEntry  
SEQUENCE    
  frUniSigStateChange Counter32
  frUniSigRemoteBusy Counter32
  frUniSigReceiveRejectFrame Counter32
  frUniSigAckTimeout Counter32
  frUniSigIFramesTransmitted Counter32
  frUniSigIFramesTxDiscarded Counter32
  frUniSigIFramesReceived Counter32
  frUniSigIFramesRcvdDiscarded Counter32

FrUniSigSvcaccEntry  
SEQUENCE    
  frUniSigDefaultAccounting INTEGER

FrUniSigCodesEntry  
SEQUENCE    
  frUniSigLastClearRemoteDataNetworkAddress DigitString
  frUniSigLastClearCause Unsigned32
  frUniSigLastDiagnosticCode Unsigned32

FrUniVFramerRowStatusEntry  
SEQUENCE    
  frUniVFramerRowStatus RowStatus
  frUniVFramerComponentName DisplayString
  frUniVFramerStorageType StorageType
  frUniVFramerIndex NonReplicated

FrUniVFramerProvEntry  
SEQUENCE    
  frUniVFramerOtherVirtualFramer Link
  frUniVFramerLogicalProcessor Link

FrUniVFramerStateEntry  
SEQUENCE    
  frUniVFramerAdminState INTEGER
  frUniVFramerOperationalState INTEGER
  frUniVFramerUsageState INTEGER

FrUniVFramerStatsEntry  
SEQUENCE    
  frUniVFramerFrmToOtherVFramer PassportCounter64
  frUniVFramerFrmFromOtherVFramer PassportCounter64
  frUniVFramerOctetFromOtherVFramer PassportCounter64

FrUniLtsRowStatusEntry  
SEQUENCE    
  frUniLtsRowStatus RowStatus
  frUniLtsComponentName DisplayString
  frUniLtsStorageType StorageType
  frUniLtsIndex NonReplicated

FrUniLtsSetupEntry  
SEQUENCE    
  frUniLtsDuration Unsigned32
  frUniLtsAlgorithm INTEGER
  frUniLtsBurstSize Unsigned32
  frUniLtsTimeInterval Unsigned32

FrUniLtsStateEntry  
SEQUENCE    
  frUniLtsGeneratorState INTEGER
  frUniLtsCycleIncomplete INTEGER
  frUniLtsLastActiveInterval Unsigned32
  frUniLtsLoad FixedPoint3
  frUniLtsElapsedGenerationTime Unsigned32

FrUniLtsResultsEntry  
SEQUENCE    
  frUniLtsFramesTx Counter32
  frUniLtsBytesTx Unsigned32
  frUniLtsBitRateTx FixedPoint3
  frUniLtsFrameRateTx Unsigned32

FrUniLtsPatRowStatusEntry  
SEQUENCE    
  frUniLtsPatRowStatus RowStatus
  frUniLtsPatComponentName DisplayString
  frUniLtsPatStorageType StorageType
  frUniLtsPatIndex Integer32

FrUniLtsPatDefaultsEntry  
SEQUENCE    
  frUniLtsPatDefaultDlci Unsigned32
  frUniLtsPatDefaultNumFrames Unsigned32
  frUniLtsPatDefaultDataSize Unsigned32
  frUniLtsPatDefaultHeaderBits OCTET STRING
  frUniLtsPatDefaultHeaderLength Unsigned32
  frUniLtsPatDefaultEABits Hex
  frUniLtsPatDefaultPayloadPattern HexString
  frUniLtsPatDefaultRfc1490Header INTEGER
  frUniLtsPatDefaultUseBadLrc INTEGER

FrUniLtsPatSetupEntry  
SEQUENCE    
  frUniLtsPatDlci Unsigned32
  frUniLtsPatNumFrames Unsigned32
  frUniLtsPatDataSize Unsigned32
  frUniLtsPatHeaderBits OCTET STRING
  frUniLtsPatHeaderLength Unsigned32
  frUniLtsPatEaBits Hex
  frUniLtsPatPayloadPattern HexString
  frUniLtsPatRfc1490Header INTEGER
  frUniLtsPatUseBadLrc INTEGER

FrUniLtsPatOpDataEntry  
SEQUENCE    
  frUniLtsPatFramePattern HexString
  frUniLtsPatHdlcBitsInserted Unsigned32

FrUniLtsPatOpStateEntry  
SEQUENCE    
  frUniLtsPatLoad FixedPoint3
  frUniLtsPatStatus INTEGER

Defined Values

frameRelayUniMIB 1.1.562.2.4.2.24
OBJECT IDENTIFIER    

frUni 1.1.562.2.4.1.71
OBJECT IDENTIFIER    

frUniRowStatusTable 1.1.562.2.4.1.71.1
This entry controls the addition and deletion of frUni components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniRowStatusEntry

frUniRowStatusEntry 1.1.562.2.4.1.71.1.1
A single entry in the table represents a single frUni component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniRowStatusEntry  

frUniRowStatus 1.1.562.2.4.1.71.1.1.1
This variable is used as the basis for SNMP naming of frUni components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frUniComponentName 1.1.562.2.4.1.71.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniStorageType 1.1.562.2.4.1.71.1.1.4
This variable represents the storage type value for the frUni tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniIndex 1.1.562.2.4.1.71.1.1.10
This variable represents the index for the frUni tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

frUniCidDataTable 1.1.562.2.4.1.71.10
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniCidDataEntry

frUniCidDataEntry 1.1.562.2.4.1.71.10.1
An entry in the frUniCidDataTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniCidDataEntry  

frUniCustomerIdentifier 1.1.562.2.4.1.71.10.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

frUniStateTable 1.1.562.2.4.1.71.11
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniStateEntry

frUniStateEntry 1.1.562.2.4.1.71.11.1
An entry in the frUniStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniStateEntry  

frUniAdminState 1.1.562.2.4.1.71.11.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

frUniOperationalState 1.1.562.2.4.1.71.11.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

frUniUsageState 1.1.562.2.4.1.71.11.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

frUniAvailabilityStatus 1.1.562.2.4.1.71.11.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

frUniProceduralStatus 1.1.562.2.4.1.71.11.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

frUniControlStatus 1.1.562.2.4.1.71.11.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

frUniAlarmStatus 1.1.562.2.4.1.71.11.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

frUniStandbyStatus 1.1.562.2.4.1.71.11.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER hotStandby(0), coldStandby(1), providingService(2), notSet(15)  

frUniUnknownStatus 1.1.562.2.4.1.71.11.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

frUniStatsTable 1.1.562.2.4.1.71.12
FrUni/n Statistics This group contains the statistics about the operational behavior of the service at the interface level.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniStatsEntry

frUniStatsEntry 1.1.562.2.4.1.71.12.1
An entry in the frUniStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniStatsEntry  

frUniLastUnknownDlci 1.1.562.2.4.1.71.12.1.1
This attribute identifies the most recent DLCI which user frames were received on for which a DLCI has not been provisioned on the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..1023  

frUniUnknownDlciFramesFromIf 1.1.562.2.4.1.71.12.1.2
This attribute contains a count of the number of frames received from the interface with an unknown DLCI (DLCI which is not provisioned). When the maximum is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniInvalidHeaderFramesFromIf 1.1.562.2.4.1.71.12.1.3
This attribute counts the number of frames received from the interface with an invalid header format. When the maximum is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniIfEntryTable 1.1.562.2.4.1.71.13
This group contains the provisionable attributes for the ifEntry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniIfEntryEntry

frUniIfEntryEntry 1.1.562.2.4.1.71.13.1
An entry in the frUniIfEntryTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniIfEntryEntry  

frUniIfAdminStatus 1.1.562.2.4.1.71.13.1.1
The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

frUniIfIndex 1.1.562.2.4.1.71.13.1.2
This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex 1..65535  

frUniOperStatusTable 1.1.562.2.4.1.71.14
This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniOperStatusEntry

frUniOperStatusEntry 1.1.562.2.4.1.71.14.1
An entry in the frUniOperStatusTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniOperStatusEntry  

frUniSnmpOperStatus 1.1.562.2.4.1.71.14.1.1
The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

frUniEmissionPriorityQsTable 1.1.562.2.4.1.71.15
This group contains the provisionable attribute to specifie the number of Frame Relay egress emission priority queues to be used on that Frame Relay Interface
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniEmissionPriorityQsEntry

frUniEmissionPriorityQsEntry 1.1.562.2.4.1.71.15.1
An entry in the frUniEmissionPriorityQsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniEmissionPriorityQsEntry  

frUniNumberOfEmissionQs 1.1.562.2.4.1.71.15.1.1
This attribute specifies the number of egress emission priority queues that will be used for that Frame Relay interface. The possible values of this attribute are 2 or 4: For V.35, V.11, HSSI, E1, DS1, E3, DS3 or 8pDS1 the possible values are: 2 (in which case they are hardware queues), or 4 (in which case they are software queues). For DS1C, E1C or DS3C the possible values are 2, 4 (in all cases they are software queues).
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 2 | 4  

frUniFrmToIfByQueueTable 1.1.562.2.4.1.71.341
This attribute counts the total number of frames transmitted to the interface per egress emission priority queue since the component has been activated. There is potientially a maximum of 4 emission priority queues. The number of available egress queues varies according to the value of the provisionable attribute numberOfEmissionQs. Egress queue 0 has the lowest priority, while egress queue 3 has the highest priority. The queue values are only indicated when the numberOfEmissionQs is set to 4 queues.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniFrmToIfByQueueEntry

frUniFrmToIfByQueueEntry 1.1.562.2.4.1.71.341.1
An entry in the frUniFrmToIfByQueueTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniFrmToIfByQueueEntry  

frUniFrmToIfByQueueIndex 1.1.562.2.4.1.71.341.1.1
This variable represents the index for the frUniFrmToIfByQueueTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 0..3  

frUniFrmToIfByQueueValue 1.1.562.2.4.1.71.341.1.2
This variable represents an individual value for the frUniFrmToIfByQueueTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniOctetToIfByQueueTable 1.1.562.2.4.1.71.342
This attribute counts the total number of octets transmitted from the service to the interface per emission priority queue since the component has been activated. There is potientially a maximum of 4 emission priority queues. The number of available egress queues varies according to the value of the provisionable attribute numberOfEmissionQs. Egress queue 0 has the lowest priority, while egress queue 3 has the highest priority.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniOctetToIfByQueueEntry

frUniOctetToIfByQueueEntry 1.1.562.2.4.1.71.342.1
An entry in the frUniOctetToIfByQueueTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniOctetToIfByQueueEntry  

frUniOctetToIfByQueueIndex 1.1.562.2.4.1.71.342.1.1
This variable represents the index for the frUniOctetToIfByQueueTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 0..3  

frUniOctetToIfByQueueValue 1.1.562.2.4.1.71.342.1.2
This variable represents an individual value for the frUniOctetToIfByQueueTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDna 1.1.562.2.4.1.71.2
OBJECT IDENTIFIER    

frUniDnaRowStatusTable 1.1.562.2.4.1.71.2.1
This entry controls the addition and deletion of frUniDna components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDnaRowStatusEntry

frUniDnaRowStatusEntry 1.1.562.2.4.1.71.2.1.1
A single entry in the table represents a single frUniDna component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDnaRowStatusEntry  

frUniDnaRowStatus 1.1.562.2.4.1.71.2.1.1.1
This variable is used as the basis for SNMP naming of frUniDna components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

frUniDnaComponentName 1.1.562.2.4.1.71.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniDnaStorageType 1.1.562.2.4.1.71.2.1.1.4
This variable represents the storage type value for the frUniDna tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniDnaIndex 1.1.562.2.4.1.71.2.1.1.10
This variable represents the index for the frUniDna tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frUniDnaAddressTable 1.1.562.2.4.1.71.2.10
This group contains attributes common to all DNAs. Every DNA used in the network is defined with this group of 2 attributes.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDnaAddressEntry

frUniDnaAddressEntry 1.1.562.2.4.1.71.2.10.1
An entry in the frUniDnaAddressTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDnaAddressEntry  

frUniDnaNumberingPlanIndicator 1.1.562.2.4.1.71.2.10.1.1
This attribute indicates the Numbering Plan Indicator (NPI) of the DNA that is entered. Address may belong to X.121 or E.164 plans. X.121 is used in packet switched data networks.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

frUniDnaDataNetworkAddress 1.1.562.2.4.1.71.2.10.1.2
This attribute indicates the customer's unique identifier. It is the equivalent of the telephone number in the telephone network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DigitString Size(1..15)  

frUniDnaOutgoingOptionsTable 1.1.562.2.4.1.71.2.11
This group defines DNA call options for calls made from the interface. These options are not used for calls arriving to the interface represented by this DNA.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDnaOutgoingOptionsEntry

frUniDnaOutgoingOptionsEntry 1.1.562.2.4.1.71.2.11.1
An entry in the frUniDnaOutgoingOptionsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDnaOutgoingOptionsEntry  

frUniDnaOutDefaultPriority 1.1.562.2.4.1.71.2.11.1.7
This attribute indicates the default priority of outgoing calls from the DTE to the network. It can be overridden by the discardPriority under DLCI Direct Call subcomponent. This option can be also included in X.25 signalling, in such case it will be overruled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER normal(0), high(1)  

frUniDnaOutDefaultPathSensitivity 1.1.562.2.4.1.71.2.11.1.11
This attribute specifies the default class of path sensitivity to network for all outgoing calls that use this DNA. The chosen default class of path sensitivity applies to all outgoing calls established using this DNA. This attribute, if set to throughput, indicates that the default class is throughput sensitive. If set to delay, then the default class is delay sensitive. The default of outDefaultPathSensitivity is throughput.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER throughput(0), delay(1)  

frUniDnaOutPathSensitivityOverRide 1.1.562.2.4.1.71.2.11.1.12
If this attribute is set to yes in the call request, the called end will use the calling end provisioning data on path sensitivity to override its own provisioning data. The default of outPathSensitivityOverRide is yes.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

frUniDnaOutDefaultPathReliability 1.1.562.2.4.1.71.2.11.1.14
This attribute specifies the default class of routing for reliability routing for all outgoing calls (from the DTE to the network) using this particular DNA. The chosen default class of routing applies to all outgoing calls established using this DNA, and applies to the packets travelling in both directions on all outgoing calls (local to remote, and remote to local). For incoming calls, the default class of routing is chosen by the calling party (as opposed to DPN, where either end of the call can choose the default routing class). This attribute, if set to a value of normal, indicates that the default class of routing is normal reliability routing. If set to a value of high, then the default class of routing is high reliability routing. High reliability is the standard choice for most DPN and Passport services. It usually indicates that packets are overflowed or retransmitted at various routing levels. Typically high reliability results in duplication and disordering of packets in the network when errors are detected or during link congestion. However, the VC handles the duplication and disordering to ensure that packets are delivered to the DTE properly. For the Frame Relay service, duplication of packets is not desired, in which case, normal reliability may be chosen as the preferred class of routing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER high(0), normal(1)  

frUniDnaOutAccess 1.1.562.2.4.1.71.2.11.1.17
This attribute is an extension of the Closed User Group (CUG) facility, as follows: This attribute, if set to a value of allowed indicates that outgoing calls (from the DTE to the network) to the open (non-CUG) part of the network are permitted. It also permits outgoing calls to DTEs that have Incoming Access capabilities. If set to a value of disallowed, then such calls cannot be made using this DNA. Such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Closed User Group with Outgoing Access' feature for DNAs in that outgoing access is granted if this attribute is set to a value of allowed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

frUniDnaDefaultTransferPriority 1.1.562.2.4.1.71.2.11.1.18
This attribute specifies the default transfer priority for all outgoing calls using this particular DNA. It can be overridden by the transferPriority provisioned in the Dlci DirectCall sub-component. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 levels from 0 to 15. Each transfer priority n, where n indicates the transfer priority index, contains a default setting for routing class of service (multimedia, delay or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required. The default defaultTransferPriority is 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15)  

frUniDnaTransferPriorityOverRide 1.1.562.2.4.1.71.2.11.1.19
When this attribute is set to yes in the call request, the called end will use the calling end provisioning data on transfer priority to override its own provisioning data. If it is set no, the called end will use its own provisioning data on transfer priority. This attribute is not applicable for Frame Relay SVCs. For more information about transfer priority, please refer to the previous attribute defaultTransferPriority. The default of transferPriorityOverRide is yes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

frUniDnaIncomingOptionsTable 1.1.562.2.4.1.71.2.12
This group defines options for incoming calls. These options are used for calls arriving to the interface represented by this DNA. For calls originated from the interface, IncomingOptions attributes are not used.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDnaIncomingOptionsEntry

frUniDnaIncomingOptionsEntry 1.1.562.2.4.1.71.2.12.1
An entry in the frUniDnaIncomingOptionsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDnaIncomingOptionsEntry  

frUniDnaIncAccess 1.1.562.2.4.1.71.2.12.1.9
This attribute, if set to a value of allowed specifies that incoming calls (from the network to the DTE) from the open (non-CUG) part of the network are permitted. It also permits incoming calls from DTEs that have outgoing access capabilities. If set to a value of disallowed, such calls cannot be made to this DNA. They will be cleared by the local DCE. This attribute corresponds to the CCITT 'Closed User Group with Incoming Access' feature for DNAs in that incoming access is granted if this attribute is set to a value of allowed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

frUniDnaCallOptionsTable 1.1.562.2.4.1.71.2.13
This group defines additional all options for not related to direction of the call.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDnaCallOptionsEntry

frUniDnaCallOptionsEntry 1.1.562.2.4.1.71.2.13.1
An entry in the frUniDnaCallOptionsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDnaCallOptionsEntry  

frUniDnaAccountClass 1.1.562.2.4.1.71.2.13.1.10
This attribute specifies the accounting class which is reserved for network operations usage. Its value is returned in the accounting record in the local and remote service type attributes. Use of this attribute is decided by network operator. This attribute is returned by the local VC in the accounting record for all calls that are set up using this particular DNA.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

frUniDnaAccountCollection 1.1.562.2.4.1.71.2.13.1.11
This attribute indicates that accounting records are to be collected by the network for the various reasons: billing, test, study, auditing. The last of the parameters, force, indicates that accounting records are to be collected irrespective of other collection reasons. The force option is available for X.75 Gateways only. If none of these reasons are set, then accounting will be suppressed. To set a specific accounting collection reason, the reason is entered and the corresponding bit in the structure is set to a value of 1. To turn off a specific accounting collection reason, the reason is entered preceded with the '~' character, and the corresponding bit in the structure is set to a value of 0. The bit placement for the accounting collection reasons is as follows: Bit 0 - Bill Bit 1 - Test Bit 2 - Study Bit 3 - Audit Bit 4 - Force Description of bits: bill(0) test(1) study(2) audit(3) force(4)
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1)  

frUniDnaServiceExchange 1.1.562.2.4.1.71.2.13.1.12
This attribute is an arbitrary number, Data Service Exchange, as entered by the network operator and reported in accounting record. It is converted into an internal 8-bit integer value for use in the accounting record as well as in various X.25 and X.75 Tariff utilities.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

frUniDnaEgressAccounting 1.1.562.2.4.1.71.2.13.1.13
This attribute specifies if egress accounting is enabled by the frame relay service. If egress accounting is disabled, only segment counts are collected by the VC. No frame relay counts appear in the accounting records for the frame relay service. If egress accounting is enabled, the accounting records for the frame relay service will contain frame relay specific counts.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

frUniDnaDataPath 1.1.562.2.4.1.71.2.13.1.21
This attribute specifies the data path to be used by Virtual Circuits on this interface. If the connection has a DirectCall component then the value can be overridden by the dataPath attribute of the DirectCall component. This value applies to the connection after data transfer state is reached. All the data and control trafic will be sent using this data path. If the provisioned dataPath is not available the connection is not established. The value of the dataPath is signalled by both ends of the connection. If this value is not the same at both ends dprsOnly is used for the duration of the connection. A virtual circuit connection is always established using dprsOnly even if this attribute is provisioned as some other value. dprsOnly - dynamic packet routing system is used dprsMcsOnly - dprs Multi-Service Cut-Through Switching path is used. dprsMcsFirst - dprs Multi-Service Cut-Through Switching path is used if it is available. If it is not avaliable dprsOnly is used.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dprsOnly(0), dprsMcsOnly(1), dprsMcsFirst(2)  

frUniDnaCug 1.1.562.2.4.1.71.2.2
OBJECT IDENTIFIER    

frUniDnaCugRowStatusTable 1.1.562.2.4.1.71.2.2.1
This entry controls the addition and deletion of frUniDnaCug components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDnaCugRowStatusEntry

frUniDnaCugRowStatusEntry 1.1.562.2.4.1.71.2.2.1.1
A single entry in the table represents a single frUniDnaCug component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDnaCugRowStatusEntry  

frUniDnaCugRowStatus 1.1.562.2.4.1.71.2.2.1.1.1
This variable is used as the basis for SNMP naming of frUniDnaCug components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frUniDnaCugComponentName 1.1.562.2.4.1.71.2.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniDnaCugStorageType 1.1.562.2.4.1.71.2.2.1.1.4
This variable represents the storage type value for the frUniDnaCug tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniDnaCugIndex 1.1.562.2.4.1.71.2.2.1.1.10
This variable represents the index for the frUniDnaCug tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

frUniDnaCugCugOptionsTable 1.1.562.2.4.1.71.2.2.10
Attributes in this group define ClosedUserGroup options associated with interlockCode. DNA's with the same CUG (interlockCode) can make calls within this group. Various combinations which permit or prevent calls in the same CUG group are defined here.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDnaCugCugOptionsEntry

frUniDnaCugCugOptionsEntry 1.1.562.2.4.1.71.2.2.10.1
An entry in the frUniDnaCugCugOptionsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDnaCugCugOptionsEntry  

frUniDnaCugType 1.1.562.2.4.1.71.2.2.10.1.1
This attribute specifies the CUG type - the CUG is either a national CUG, or an international CUG. International closed user groups are usually established between DTEs for which there is an X.75 Gateway between; whereas national closed user groups are usually established between DTEs for which there is no X.75 Gateway between. (National CUGs cannot normally traverse an X.75 Gateway). If this attribute is set to national, then the CUG is a national CUG, in which case, the dnic should be left at its default value since it is not part of a national CUG. If this attribute is set to international, then the CUG is an international CUG, in which case, the dnic should be set appropriately as part of the CUG interlockCode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER national(0), international(1)  

frUniDnaCugDnic 1.1.562.2.4.1.71.2.2.10.1.2
This attribute specifies the dnic (Data Network ID Code) of the CUG by which packet networks are identified. This attribute is not applicable if the CUG is a national CUG, as specified by the CUG type attribute. There are usually 1 or 2 dnics assigned per country, for public networks. The U.S. is an exception where each BOC has a dnic. Also, a group of private networks can have its own dnic. dnic value is not an arbitrary number. It is assigned by international agreement and controlled by CCITT.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DigitString Size(4)  

frUniDnaCugInterlockCode 1.1.562.2.4.1.71.2.2.10.1.3
This attribute specifies the CUG identifier of a national or international CUG call. It is an arbitrary number and it also can be called CUG in some descriptions. Interfaces (DNA's) defined with this number can make calls to DNA's with the same interlockCode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

frUniDnaCugPreferential 1.1.562.2.4.1.71.2.2.10.1.4
The attribute 'preferential', if set to yes indicates that this CUG is the SIMPLE CUG (as defined in ITU X.36 [10/96]), in which case it will be used during the call establishment phase if the DTE has not explicitly specified a CUG index in the call request packet. If set to no, then this CUG is not the SIMPLE CUG, but an instance of the SELECTABLE CUG. The attribute 'preferential' is set to no by CAS when a CUG instance is created. If only one CUG instance exists under a DNA, and if this CUG's attributes 'incCalls' and 'outCall' are both set to allowed, then this CUG instance can be changed to a SIMPLE CUG by setting the attribute 'preferential' to yes. If more than one CUG instances exist under a DNA, none of the CUGs can be set by the user as 'preferential'. Essentially, the attribute 'preferential' distinguishes a SIMPLE CUG from a SELECTABLE CUG. In the case of a FRUNI DNA with a single CUG instance, the CUG can be a SIMPLE CUG (preferential = yes) or the only instance of a SELECTABLE CUG (preferential = no).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

frUniDnaCugOutCalls 1.1.562.2.4.1.71.2.2.10.1.5
This attribute, if set to allowed indicates that outgoing calls (from the DTE into the network) can be made using this particular CUG. If set to a value of disallowed, then outgoing calls cannot be made using this CUG - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Outgoing Calls Barred' feature for CUGs in that outgoing calls are barred if this attribute is set to a value of disallowed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

frUniDnaCugIncCalls 1.1.562.2.4.1.71.2.2.10.1.6
This attribute, if set to allowed indicates that incoming calls (from the network to the DTE) can be made using this particular CUG. If set to disallowed, then incoming calls cannot be made using this CUG - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Incoming Calls Barred' feature for CUGs in that incoming calls are barred if this attribute is set to a value of disallowed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

frUniDnaHgM 1.1.562.2.4.1.71.2.3
OBJECT IDENTIFIER    

frUniDnaHgMRowStatusTable 1.1.562.2.4.1.71.2.3.1
This entry controls the addition and deletion of frUniDnaHgM components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDnaHgMRowStatusEntry

frUniDnaHgMRowStatusEntry 1.1.562.2.4.1.71.2.3.1.1
A single entry in the table represents a single frUniDnaHgM component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDnaHgMRowStatusEntry  

frUniDnaHgMRowStatus 1.1.562.2.4.1.71.2.3.1.1.1
This variable is used as the basis for SNMP naming of frUniDnaHgM components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frUniDnaHgMComponentName 1.1.562.2.4.1.71.2.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniDnaHgMStorageType 1.1.562.2.4.1.71.2.3.1.1.4
This variable represents the storage type value for the frUniDnaHgM tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniDnaHgMIndex 1.1.562.2.4.1.71.2.3.1.1.10
This variable represents the index for the frUniDnaHgM tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frUniDnaHgMIfTable 1.1.562.2.4.1.71.2.3.10
This group contains the interface parameters between the HuntGroupMember and the hunt group server.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDnaHgMIfEntry

frUniDnaHgMIfEntry 1.1.562.2.4.1.71.2.3.10.1
An entry in the frUniDnaHgMIfTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDnaHgMIfEntry  

frUniDnaHgMAvailabilityUpdateThreshold 1.1.562.2.4.1.71.2.3.10.1.1
This attribute specifies how much availableAggregateCIR can change before an Availability Message Packet (AMP) is sent to the hunt group server informing it of the change. If the value specified is not a multiple of 2048, the value actually used as the threshold will be the next higher multiple of 2048.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 2048..16777216  

frUniDnaHgMOpTable 1.1.562.2.4.1.71.2.3.11
This group contains the operational attributes of the HuntGroupMember component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDnaHgMOpEntry

frUniDnaHgMOpEntry 1.1.562.2.4.1.71.2.3.11.1
An entry in the frUniDnaHgMOpTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDnaHgMOpEntry  

frUniDnaHgMMaximumAvailableAggregateCir 1.1.562.2.4.1.71.2.3.11.1.1
This attribute indicates the maximum aggregate CIR availability for this hunt group member. It is the sum of the maximum CIRs provisioned for SVCs in the FrUni Signaling component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDnaHgMAvailableAggregateCir 1.1.562.2.4.1.71.2.3.11.1.2
This attribute indicates the current available aggregate CIR reported to the hunt group in the Availability Message Packet (AMP). It is incremented by the application when a DLCI is freed. It is decremented when a DLCI is allocated. The value is the sum of the currently available aggregate CIRs for SVCs. Both this attribute and the availableDlcis attribute must be non zero for this DNA to receive calls on the hunt group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDnaHgMAvailabilityDelta 1.1.562.2.4.1.71.2.3.11.1.3
This attribute indicates the net change in the available aggregate CIR since the last Availability Message Packet (AMP) was sent to the Hunt Group. Once the absolute value of this attribute reaches the availabilityUpdateThreshold an AMP is sent to the hunt group server(s) and the availabilityDelta is re-computed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -16777216..16777215  

frUniDnaHgMAvailableDlcis 1.1.562.2.4.1.71.2.3.11.1.5
This attribute indicates the number of DLCIs available for SVCs on the interface associated with this DNA. If this value reaches 0, an AMP with zero availability is sent to the hunt group server(s). Both this attribute and the availableAggregateCir attribute must be non zero for this DNA to receive calls on the hunt group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4096  

frUniDnaHgMHgAddr 1.1.562.2.4.1.71.2.3.2
OBJECT IDENTIFIER    

frUniDnaHgMHgAddrRowStatusTable 1.1.562.2.4.1.71.2.3.2.1
This entry controls the addition and deletion of frUniDnaHgMHgAddr components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDnaHgMHgAddrRowStatusEntry

frUniDnaHgMHgAddrRowStatusEntry 1.1.562.2.4.1.71.2.3.2.1.1
A single entry in the table represents a single frUniDnaHgMHgAddr component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDnaHgMHgAddrRowStatusEntry  

frUniDnaHgMHgAddrRowStatus 1.1.562.2.4.1.71.2.3.2.1.1.1
This variable is used as the basis for SNMP naming of frUniDnaHgMHgAddr components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frUniDnaHgMHgAddrComponentName 1.1.562.2.4.1.71.2.3.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniDnaHgMHgAddrStorageType 1.1.562.2.4.1.71.2.3.2.1.1.4
This variable represents the storage type value for the frUniDnaHgMHgAddr tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniDnaHgMHgAddrIndex 1.1.562.2.4.1.71.2.3.2.1.1.10
This variable represents the index for the frUniDnaHgMHgAddr tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 0..1  

frUniDnaHgMHgAddrAddrTable 1.1.562.2.4.1.71.2.3.2.10
This group contains attributes common to all DNAs. Every DNA used in the network is defined with this group of 2 attributes.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDnaHgMHgAddrAddrEntry

frUniDnaHgMHgAddrAddrEntry 1.1.562.2.4.1.71.2.3.2.10.1
An entry in the frUniDnaHgMHgAddrAddrTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDnaHgMHgAddrAddrEntry  

frUniDnaHgMHgAddrNumberingPlanIndicator 1.1.562.2.4.1.71.2.3.2.10.1.1
This attribute indicates the Numbering Plan Indicator (NPI) of the DNA. The address may belong to X.121 or E.164 plans.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

frUniDnaHgMHgAddrDataNetworkAddress 1.1.562.2.4.1.71.2.3.2.10.1.2
This attribute contains digits which form the unique identifier of the customer interface. It can be compared (approximation only) to a telephone number where the phone number identifies a unique telephone set. DNA digits are selected and assigned by network operators.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DigitString Size(1..15)  

frUniFramer 1.1.562.2.4.1.71.3
OBJECT IDENTIFIER    

frUniFramerRowStatusTable 1.1.562.2.4.1.71.3.1
This entry controls the addition and deletion of frUniFramer components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniFramerRowStatusEntry

frUniFramerRowStatusEntry 1.1.562.2.4.1.71.3.1.1
A single entry in the table represents a single frUniFramer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniFramerRowStatusEntry  

frUniFramerRowStatus 1.1.562.2.4.1.71.3.1.1.1
This variable is used as the basis for SNMP naming of frUniFramer components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frUniFramerComponentName 1.1.562.2.4.1.71.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniFramerStorageType 1.1.562.2.4.1.71.3.1.1.4
This variable represents the storage type value for the frUniFramer tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniFramerIndex 1.1.562.2.4.1.71.3.1.1.10
This variable represents the index for the frUniFramer tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frUniFramerProvTable 1.1.562.2.4.1.71.3.10
This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisionable Framer groups.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniFramerProvEntry

frUniFramerProvEntry 1.1.562.2.4.1.71.3.10.1
An entry in the frUniFramerProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniFramerProvEntry  

frUniFramerInterfaceName 1.1.562.2.4.1.71.3.10.1.1
This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

frUniFramerLinkTable 1.1.562.2.4.1.71.3.11
This group contains attributes defining the framing of data on the link interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniFramerLinkEntry

frUniFramerLinkEntry 1.1.562.2.4.1.71.3.11.1
An entry in the frUniFramerLinkTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniFramerLinkEntry  

frUniFramerFlagsBetweenFrames 1.1.562.2.4.1.71.3.11.1.4
This attribute defines the number of flags that are inserted between frames sent to the link interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..16  

frUniFramerStateTable 1.1.562.2.4.1.71.3.12
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniFramerStateEntry

frUniFramerStateEntry 1.1.562.2.4.1.71.3.12.1
An entry in the frUniFramerStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniFramerStateEntry  

frUniFramerAdminState 1.1.562.2.4.1.71.3.12.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

frUniFramerOperationalState 1.1.562.2.4.1.71.3.12.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

frUniFramerUsageState 1.1.562.2.4.1.71.3.12.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

frUniFramerStatsTable 1.1.562.2.4.1.71.3.13
This group contains the operational statistics data for a Framer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniFramerStatsEntry

frUniFramerStatsEntry 1.1.562.2.4.1.71.3.13.1
An entry in the frUniFramerStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniFramerStatsEntry  

frUniFramerFrmToIf 1.1.562.2.4.1.71.3.13.1.1
The number of frames transmitted to the link interface by Framer. Note: This does not include the number of frames transmitted directly to the hardware queue, thus bypassing the Framer component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniFramerFrmFromIf 1.1.562.2.4.1.71.3.13.1.2
The number of frames received from the link interface by Framer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniFramerOctetFromIf 1.1.562.2.4.1.71.3.13.1.3
The number of bytes received from the link interface by Framer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniFramerAborts 1.1.562.2.4.1.71.3.13.1.4
This attribute is the total number of aborts received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniFramerCrcErrors 1.1.562.2.4.1.71.3.13.1.5
This attribute is the total number of frames with CRC errors, occurring in the receive direction from the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniFramerLrcErrors 1.1.562.2.4.1.71.3.13.1.6
This attribute is the total number of frames with LRC errors, occurring in the Tx link prior to transmission onto the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniFramerNonOctetErrors 1.1.562.2.4.1.71.3.13.1.7
This attribute is the total number of frames that were non octet aligned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniFramerOverruns 1.1.562.2.4.1.71.3.13.1.8
This attribute is the total number of frames received from the link for which overruns occurred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniFramerUnderruns 1.1.562.2.4.1.71.3.13.1.9
This attribute is the total number of frames transmitted to the link for which underruns occurred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniFramerLargeFrmErrors 1.1.562.2.4.1.71.3.13.1.10
This attribute is the total number of frames received which were too large. The frame execeeded the maximumFrameLengthLimit provisioned attribute or it contained more than the 255 block hardware limit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniFramerFrmModeErrors 1.1.562.2.4.1.71.3.13.1.11
This attribute is the total number of frames detected with framing mode errors. A framingModeError is flagged when frames are inconsistent with the specified framingType, that is when interrupting frames are used while running in hdlc mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniFramerUtilTable 1.1.562.2.4.1.71.3.14
This group contains the link utilizaiton operational data for a Framer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniFramerUtilEntry

frUniFramerUtilEntry 1.1.562.2.4.1.71.3.14.1
An entry in the frUniFramerUtilTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniFramerUtilEntry  

frUniFramerNormPrioLinkUtilToIf 1.1.562.2.4.1.71.3.14.1.1
This attribute is the utilization of the normal and high priority data traffic (interruptable traffic) sent to the link as a percentage of the available bandwidth on the link. Note that this includes traffic with Transfer Priorities (TP) of 0, 6 and 9 and/or Emission Priority of 2 and 3. The utilization is the average for the last minute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..100  

frUniFramerNormPrioLinkUtilFromIf 1.1.562.2.4.1.71.3.14.1.3
This attribute is the utilization of the normal and high priority data traffic (interruptable traffic) received from the link as a percentage of the available bandwidth on the link. Note that this includes traffic with Transfer Priorities (TP) of 0, 6 and 9 and/or Emission Priority of 2 and 3. The utilization is the average for the last minute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..100  

frUniLmi 1.1.562.2.4.1.71.4
OBJECT IDENTIFIER    

frUniLmiRowStatusTable 1.1.562.2.4.1.71.4.1
This entry controls the addition and deletion of frUniLmi components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLmiRowStatusEntry

frUniLmiRowStatusEntry 1.1.562.2.4.1.71.4.1.1
A single entry in the table represents a single frUniLmi component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLmiRowStatusEntry  

frUniLmiRowStatus 1.1.562.2.4.1.71.4.1.1.1
This variable is used as the basis for SNMP naming of frUniLmi components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

frUniLmiComponentName 1.1.562.2.4.1.71.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniLmiStorageType 1.1.562.2.4.1.71.4.1.1.4
This variable represents the storage type value for the frUniLmi tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniLmiIndex 1.1.562.2.4.1.71.4.1.1.10
This variable represents the index for the frUniLmi tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frUniLmiParmsTable 1.1.562.2.4.1.71.4.10
This group contains the provisionable attributes of the LMI component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLmiParmsEntry

frUniLmiParmsEntry 1.1.562.2.4.1.71.4.10.1
An entry in the frUniLmiParmsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLmiParmsEntry  

frUniLmiProcedures 1.1.562.2.4.1.71.4.10.1.1
This attribute selects the procedures to be used for the Local Management Interface. The following procedures are supported: none: no Local Management Interface procedures are running on this interface. This accommodates Frame Relay user equipment that has not implemented any LMI procedures. The remaining attributes of this group are ignored. vendorForum: Local Management Interface procedures from the Vendor Forum specification are supported on this interface. DLCI 1023 is used for the LMI protocol. This value cannot be used if the side attribute is both. ansi: Local Management Interface procedures from the ANSI specification are supported. DLCI 0 is used for the LMI protocol. itu: Local Management Interface procedures from the ITU-T specification are supported. DLCI 0 is used for the LMI protocol. Was previously ccitt. autoConfigure: The interface determines automatically which Local Management Interface procedures to use. This value cannot be used if the side attribute is user. The procedures currently in use can be seen in the operational attribute opProcedures.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(0), vendorForum(1), ansi(2), itu(3), autoConfigure(4)  

frUniLmiAsyncStatusReport 1.1.562.2.4.1.71.4.10.1.2
This attribute selects the use of asynchronous PVC status report procedures as specified in ANSI, CCITT, and Vendor Forum. This attribute can be set to on or off. If procedures is set to none, this attribute is ignored.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

frUniLmiErrorEventThreshold 1.1.562.2.4.1.71.4.10.1.3
An event is defined as follows: (1) receipt of a STATUS ENQUIRY message; or (2) expiration of timer T392. An error event is (1) nonreceipt of STATUS ENQUIRY in T392 seconds; (2) invalid contents of a LMI message; (3) invalid receive sequence number. This attribute specifies the number of error events which, if they occur within eventCount events, cause a protocol error condition. The condition is cleared after eventCount sequential correct events occur. This attribute corresponds to the nN2 parameter described in the Vendor Forum Specification. It must be less than or equal to eventCount.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..10  

frUniLmiEventCount 1.1.562.2.4.1.71.4.10.1.4
This attribute specifies the number of contiguous events within which no more than eventErrorThreshold error events are allowed. This attribute corresponds to the nN3 parameter described in the Vendor Forum Specification. It must be greater than or equal to errorEventThreshold.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..10  

frUniLmiCheckPointTimer 1.1.562.2.4.1.71.4.10.1.5
This attribute selects the time (in seconds) within which a STATUS ENQUIRY message is expected. This attribute corresponds to the nT2 parameter described in the Vendor Forum Specification. It must be less than messageCountTimer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 5 | 10 | 15 | 20 | 25 | 30  

frUniLmiMessageCountTimer 1.1.562.2.4.1.71.4.10.1.6
This attribute selects the time (in seconds) within which at most five (this is a fixed value and corresponds to maximum message count in VendorForum) STATUS ENQUIRY messages are expected. This attribute applies only when the lmiProcedures is set to vendorForum. messageCountTimer must always be greater than checkPointTimer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 5 | 10 | 15 | 20 | 25 | 30  

frUniLmiIgnoreActiveBit 1.1.562.2.4.1.71.4.10.1.7
This attribute specifies whether the Frame Relay LMI Active Bit (A-bit) has a bearing on the transfer of user data across this Frame Relay interface for both directions of traffic flow. When this attribute is set to yes, the A-bit status of a user DLCI connection does not affect data transfer. When this attribute is set to no, data received from the local interface will be discarded if an A-bit =0 condition exists towards the local user. Data being sent to the local interface is discarded if an A-bit = 0 condition exists towards the subnet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

frUniLmiSide 1.1.562.2.4.1.71.4.10.1.8
This attribute can be set to user, network, or both. When this attribute is set to user, USP LMI procedures are running. When this attribute is set to network, NSP LMI procedures are running. When this attribute is set to both, USPNSP LMI procedures are running. When the value is both, the procedures attribute must not be set to vendorForum. Setting the value to user when the procedures attribute is set to autoConfigure is disallowed semantically.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER network(0), user(1), both(2)  

frUniLmiPvcConfigParmsInFsr 1.1.562.2.4.1.71.4.10.1.9
When this attribute is set to yes, additional Q.933 information elements are included in the LMI Full Status message to facilitate CPE PVC parameter configuring. When set to yes, the Check Prov command fails if the Lmi side is not set to network. When set to yes, Check Prov fails if the number of DLCIs on the FrUni is greater than 300. If the service is not a FrUni this attribute is ignored.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

frUniLmiStateTable 1.1.562.2.4.1.71.4.11
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLmiStateEntry

frUniLmiStateEntry 1.1.562.2.4.1.71.4.11.1
An entry in the frUniLmiStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLmiStateEntry  

frUniLmiAdminState 1.1.562.2.4.1.71.4.11.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

frUniLmiOperationalState 1.1.562.2.4.1.71.4.11.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

frUniLmiUsageState 1.1.562.2.4.1.71.4.11.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

frUniLmiPsiTable 1.1.562.2.4.1.71.4.12
This group provides the protocol status of the Local Management Interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLmiPsiEntry

frUniLmiPsiEntry 1.1.562.2.4.1.71.4.12.1
An entry in the frUniLmiPsiTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLmiPsiEntry  

frUniLmiProtocolStatus 1.1.562.2.4.1.71.4.12.1.1
This attribute indicates whether the LMI is in an error condition or whether the LMI procedures are behaving normally. When operating with no LMI protocol, this attribute is always set to normalCondition. When operating with LMI procedures, this attribute is set to errorCondition after n392 of the last n393 events are in error. The consequence of an errorCondition is that all DLCIs on this interface will become inactive in both directions. The errorCondition is cleared and a normalCondition is indicated when a sufficient number of events have occurred without error. In ANSI, this occurs when n393 consecutive good events take place. If the procedures attribute is set to autoConfigure, this attribute is set to configuring while adaptive LMI determines which LMI procedures are running on the link. A single LMI error event during auto configuration causes the attribute value to change to errorCondition. If during configuring no LMI message is received, an LMI errorCondition is raised after n392 x t392 seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER errorCondition(0), normalCondition(1), configuring(2)  

frUniLmiOpProcedures 1.1.562.2.4.1.71.4.12.1.2
The opProcedures attribute indicates the procedures being used for the Local Management Interface. This attribute should be ignored if protocolStatus is not normalCondition. The following procedures are supported: none: Local Management Interface procedures are not running on this interface. This accommodates Frame Relay user equipment that has not implemented any LMI procedures. vendorForum: Local Management Interface procedures from the Vendor Forum specification are running on this interface. DLCI 1023 is used for the LMI protocol. ansi: Local Management Interface procedures from the ANSI specification are running. DLCI 0 is used for the LMI protocol. itu: Local Management Interface procedures from the ITU-T specification are running. DLCI 0 is used for the LMI protocol. Was previously ccitt. unknown: Local Management Interface procedures have yet to be determined by Adaptive LMI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(0), vendorForum(1), ansi(2), itu(3), unknown(4)  

frUniLmiStatsTable 1.1.562.2.4.1.71.4.13
This group contains the operational statistics for the Frame Relay Local Management Interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLmiStatsEntry

frUniLmiStatsEntry 1.1.562.2.4.1.71.4.13.1
An entry in the frUniLmiStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLmiStatsEntry  

frUniLmiKeepAliveStatusToIf 1.1.562.2.4.1.71.4.13.1.1
This attribute counts the number of Local Management Interface keep alive status messages sent to the external user device in response to a status enquiry for keep alive status. When the maximum count is exceeded it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniLmiFullStatusToIf 1.1.562.2.4.1.71.4.13.1.2
This attribute counts the number of Local Management Interface full status messages sent to the external user device in response to a status enquiry for keep alive or full status. When the maximum count is reached it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniLmiKeepAliveStatusEnqFromIf 1.1.562.2.4.1.71.4.13.1.3
This attribute counts the number of Local Management Interface valid keep alive status enquiry messages received from the external user device. When the maximum count is reached it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniLmiFullStatusEnqFromIf 1.1.562.2.4.1.71.4.13.1.4
This attribute counts the number of Local Management Interface valid full status enquiry messages received from the external user device. When the maximum count is reached it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniLmiNetworkSideEventHistory 1.1.562.2.4.1.71.4.13.1.5
This attribute displays the Local Management Interface network side procedure event history in order of occurrence. An event is represented by a single symbol. A '+' symbol indicates a good event. An 'X' symbol indicates a protocol error event. The leftmost event is the most recent to occur. The provisioned eventCount (nN3/ N393) dictates the maximum number of events displayed. A good event is triggered by receipt of a valid status enquiry message. An error event is one of three possibilities, either a nT2/T392 timer expiry, receipt of a status enquiry message with bad sequence numbers, or when lmiProcedures is provisioned to vendorForum and we receive more than nN4 status enquiry messages within the provisioned messageCountTimer (nT3).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(1..10)  

frUniLmiProtocolErrors 1.1.562.2.4.1.71.4.13.1.6
This attribute counts the number of Local Management Interface protocol errors. It is the sum of the sequence (sequenceErrors), timeout (pollingVerifTimeouts) and too many status enquiry messages received within the messageCountTimer (nT3) errors. The too many status enquiries error only applies when lmiProcedures is set to vendorForum. When the maximum count is exceeded it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniLmiUnexpectedIes 1.1.562.2.4.1.71.4.13.1.7
This attribute counts the number of Local Management Interface frames received with an Information Element identifier that is unknown or unexpected. An unexpected Information Element is not a protocol error. When the maximum count is reached, this counter wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniLmiSequenceErrors 1.1.562.2.4.1.71.4.13.1.8
This attribute counts the number of Local Management Interface Status Enquiry message sequence errors. A sequence error is receipt of a Status Enquiry message with a receive sequence number not equal to the last send sequence number. When the maximum count is reached the counter wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniLmiUnexpectedReports 1.1.562.2.4.1.71.4.13.1.9
This attribute counts the number of Local Management Interface frames received with an unknown or unexpected report type. An unexpected report type is not a protocol error. When the maximum count is reached the counter wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniLmiPollingVerifTimeouts 1.1.562.2.4.1.71.4.13.1.10
This attribute counts the number of checkPointTImer (t392) timer expiries occurring on the Local Management Interface. When the maximum count is reached the counter wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniLmiKeepAliveEnqToIf 1.1.562.2.4.1.71.4.13.1.11
This attribute counts the number of Local Management Interface keep alive enquiry status messages sent to the external user device for keep alive status. When the maximum count is reached it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniLmiFullStatusEnqToIf 1.1.562.2.4.1.71.4.13.1.12
This attribute counts the number of Local Management Interface full status messages sent to the external user device in response to a status enquiry for keep alive or full status. When the maximum count is reached it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniLmiUserSideEventHistory 1.1.562.2.4.1.71.4.13.1.13
This attribute displays the Local Management Interface user side procedure event history in order of occurrence. An event is represented by a single symbol. A '+' symbol indicates a good event. An 'X' symbol indicates a protocol error event. The left most event is the most recent to occur. The provisioned eventCount (nN3/ N393) dictates the maximum number of events displayed. A good event is triggered by receipt of a valid status message. An error event is either a nT1/T391 timer expiry or receipt of a status message with bad sequence numbers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(1..10)  

frUniLmiStatusSequenceErrors 1.1.562.2.4.1.71.4.13.1.14
This attribute counts the number of Local Management Interface Status message sequence errors. A sequence error is receipt of a Status message with a receive sequence number not equal to the last send sequence number. When the maximum count is reached the counter wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniLmiNoStatusReportCount 1.1.562.2.4.1.71.4.13.1.15
This attribute counts the number of times when no status report or an invalid status report comes from the external network. This attribute is incremented in two cases: i) after a status enquiry is sent out and T391 timer expires without having a status report received. ii) an invalid status report is received. When the maximum count is reached it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniLmiUspParmsTable 1.1.562.2.4.1.71.4.14
This group contains the provisionable attributes of the Local Management Interface user side procedure.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLmiUspParmsEntry

frUniLmiUspParmsEntry 1.1.562.2.4.1.71.4.14.1
An entry in the frUniLmiUspParmsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLmiUspParmsEntry  

frUniLmiFullStatusPollingCycles 1.1.562.2.4.1.71.4.14.1.1
This attribute specifies how frequently the Frame Relay UNI service should initiate a Status Enquiry for a full PVC status report. A polling cycle is a Status Enquiry and Status Report exchange. This attribute is used only if the side attribute is either user or both.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

frUniLmiLinkVerificationTimer 1.1.562.2.4.1.71.4.14.1.2
This attribute specifies how frequently the Frame Relay UNI service should initiate a Status Enquiry for link integrity verification. It must be less than checkPointTimer (t392). When the Lmi side is network, this attribute is ignored.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 5 | 10 | 15 | 20 | 25 | 30  

frUniDlci 1.1.562.2.4.1.71.5
OBJECT IDENTIFIER    

frUniDlciRowStatusTable 1.1.562.2.4.1.71.5.1
This entry controls the addition and deletion of frUniDlci components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciRowStatusEntry

frUniDlciRowStatusEntry 1.1.562.2.4.1.71.5.1.1
A single entry in the table represents a single frUniDlci component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciRowStatusEntry  

frUniDlciRowStatus 1.1.562.2.4.1.71.5.1.1.1
This variable is used as the basis for SNMP naming of frUniDlci components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frUniDlciComponentName 1.1.562.2.4.1.71.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniDlciStorageType 1.1.562.2.4.1.71.5.1.1.4
This variable represents the storage type value for the frUniDlci tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniDlciIndex 1.1.562.2.4.1.71.5.1.1.10
This variable represents the index for the frUniDlci tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 16..1007  

frUniDlciStateTable 1.1.562.2.4.1.71.5.10
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciStateEntry

frUniDlciStateEntry 1.1.562.2.4.1.71.5.10.1
An entry in the frUniDlciStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciStateEntry  

frUniDlciAdminState 1.1.562.2.4.1.71.5.10.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

frUniDlciOperationalState 1.1.562.2.4.1.71.5.10.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

frUniDlciUsageState 1.1.562.2.4.1.71.5.10.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

frUniDlciAvailabilityStatus 1.1.562.2.4.1.71.5.10.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

frUniDlciProceduralStatus 1.1.562.2.4.1.71.5.10.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

frUniDlciControlStatus 1.1.562.2.4.1.71.5.10.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

frUniDlciAlarmStatus 1.1.562.2.4.1.71.5.10.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

frUniDlciStandbyStatus 1.1.562.2.4.1.71.5.10.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER hotStandby(0), coldStandby(1), providingService(2), notSet(15)  

frUniDlciUnknownStatus 1.1.562.2.4.1.71.5.10.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

frUniDlciAbitTable 1.1.562.2.4.1.71.5.12
This group contains the A-Bit status information for this Data Link Connection Identifier. A-Bit status information is only applicable for PVCs. For SVCs, the values of attributes under this group are all notApplicable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciAbitEntry

frUniDlciAbitEntry 1.1.562.2.4.1.71.5.12.1
An entry in the frUniDlciAbitTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciAbitEntry  

frUniDlciABitStatusToIf 1.1.562.2.4.1.71.5.12.1.1
This attribute is the most recent A-bit status sent to the interface. The A-bit status is part of the LMI protocol, and indicates willingness to accept data from the local interface. When an inactive setting is sent out, the Frame Relay service will discard any data offered from the local interface. When an active setting is sent out, the Frame Relay service will try to process all data offered from the local interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inactive(0), active(1), notApplicable(2)  

frUniDlciABitReasonToIf 1.1.562.2.4.1.71.5.12.1.2
This attribute provides the reason (if any) for an inactive status to be sent to the interface. This reason is not applicable for an active status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), remoteUserSignaled(1), localLmiError(2), remoteLmiError(3), localLinkDown(4), remoteLinkDown(5), pvcDown(6)  

frUniDlciABitStatusFromIf 1.1.562.2.4.1.71.5.12.1.3
This attribute is the most recent A-Bit status received from the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inactive(0), active(1), notApplicable(2)  

frUniDlciABitReasonFromIf 1.1.562.2.4.1.71.5.12.1.4
This attribute provides the reason (if any) for an inactive status to be sent to the subnet. This reason is not applicable for an active status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), remoteUserSignaled(1), localLmiError(2), localLinkDown(4), missingFromLmiReport(7)  

frUniDlciLoopbackState 1.1.562.2.4.1.71.5.12.1.5
This attribute has the value on when the DLCI is in loopback mode and off otherwise. This loopback command verbs start and stop are used to initiate and terminate the loopback mode for a DLCI. While loopbackState is on, the local LMI will report to the interface the A- bit status as active. Also an active A-bit signal will be reliably propagated across the subnet to the remote DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(0), on(1)  

frUniDlciCalldTable 1.1.562.2.4.1.71.5.13
This group of attributes describes the characteristics of the call such as call type and call state.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciCalldEntry

frUniDlciCalldEntry 1.1.562.2.4.1.71.5.13.1
An entry in the frUniDlciCalldTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciCalldEntry  

frUniDlciCallType 1.1.562.2.4.1.71.5.13.1.1
This attribute specifies whether this DLCI is a permancent virtual circuit (PVC) or a switched virtual circuit (SVC).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER pvc(0), svc(1)  

frUniDlciQ933CallState 1.1.562.2.4.1.71.5.13.1.2
This attribute specifies the Q.933 state of an SVC call. The value of this attribute for a PVC is always notApplicable. In the description that follows, 'local' refers to the user who has initiated the SETUP request, and 'remote' refers to the user to whom the local user wishes to connect. State description: In the null state, the network has neither received nor sent call setup requests for this DLCI. In the callInitiated state, the network has received a SETUP message from the local user. In the outgoingCallProceeding state, the network has sent a CALL PROCEEDING message to the local user in response to the SETUP message. In the callPresent state, the network has sent a SETUP message to the remote user. In the incomingCallProceeding state, the network has received a CALL PROCEEDING message from the remote user in response to a SETUP message. In the active state, either the network has sent a CONNECT message to the local user, or the network has received a CONNECT from the remote user. In the disconnectRequest state, the network has received a DISCONNECT message from the local user. In the disconnectIndication state, the network has sent a DISCONNECT to the local user. In the releaseRequest state, the network has sent out a RELEASE message to the local user.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER null(0), callInitiated(1), outgoingCallProceeding(3), callPresent(6), incomingCallProceeding(9), active(10), disconnectRequest(11), disconnectIndication(12), releaseRequest(19), notApplicable(20)  

frUniDlciQ933CallReference 1.1.562.2.4.1.71.5.13.1.3
This attribute specifies the Q.933 call reference number associated with this DLCI. The value of this attribute for a PVC is always 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..32767  

frUniDlciSpOpTable 1.1.562.2.4.1.71.5.14
This group contains the service parameters specific to this instance of DLCI. For PVCs, the values of attributes with the exception of measurementInterval should be identical to those in the group FrsDataLinkConnectionProv under the FrsUniServiceParametersProv component. For SVC's, the values of attributes may be different from the values provisioned under the Signaling subcomponent, if Q933 negotiations has ocurred to alter service parameters. DESCRIPTION
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciSpOpEntry

frUniDlciSpOpEntry 1.1.562.2.4.1.71.5.14.1
An entry in the frUniDlciSpOpTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciSpOpEntry  

frUniDlciMaximumFrameSize 1.1.562.2.4.1.71.5.14.1.1
This attribute specifies the maximum number of octets which may be included in the information field. The frame relay header and CRC octets are not included in this definition. This attribute corresponds to the dN1 parameter described in the Vendor Forum Specification.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 1..8187  

frUniDlciRateEnforcement 1.1.562.2.4.1.71.5.14.1.2
This attribute is obsolete. It provided the same information as the provisioning attribute rateEnforcement in dlci/* sp. DESCRIPTION
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER off(0), on(1)  

frUniDlciCommittedInformationRate 1.1.562.2.4.1.71.5.14.1.3
This attribute specifies the committed information rate (CIR) in bits per second (bit/s). When rateEnforcement is set to on, cir is the rate at which the network agrees to transfer information under normal conditions. This rate is measured over a measurement interval (T). This attribute should be ignored when rateEnforcement is off.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..50000000  

frUniDlciCommittedBurstSize 1.1.562.2.4.1.71.5.14.1.4
This attribute specifies the committed burst size (Bc) in bits. bc is the amount of data that a network agrees to transfer under normal conditions over a measurement interval (t). Data marked DE=1 is not accounted for in Bc. This attribute should be ignored when rateEnforcement is off.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..50000000  

frUniDlciExcessBurstSize 1.1.562.2.4.1.71.5.14.1.5
This attribute specifies the excess burst size (Be) in bits. Be is the amount of uncommitted data that the network will attempt to deliver over measurement interval T. Data marked DE=1 by the user or by the network is accounted for here. This attribute should be ignored when rateEnforcement is off.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..50000000  

frUniDlciMeasurementInterval 1.1.562.2.4.1.71.5.14.1.6
This attribute specifies the time interval (in milliseconds) over which rates and burst sizes are measured. This attribute should be ignored when rateEnforcement is off.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciRateAdaptation 1.1.562.2.4.1.71.5.14.1.7
This attribute is obsolete. It provided the information which is now in the provision attribute rateAdaptation in dlci/* sp.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER off(0), on(1), eirOnly(2)  

frUniDlciAccounting 1.1.562.2.4.1.71.5.14.1.8
This attribute specifies whether accounting data collection and record generation is turned on at this DLCI. For accounting data collection and record generation to be turned on, the accountingOn bit and at least one of the accountCollection bits in the DataNetworkAddress component must be set to on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(0), on(1)  

frUniDlciEmissionPriorityToIf 1.1.562.2.4.1.71.5.14.1.9
This attribute indicates the emission priority of frames sent to the interface. A larger value denotes a higher priority.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0 | 1 | 2 | 3  

frUniDlciTransferPriToNwk 1.1.562.2.4.1.71.5.14.1.10
This attribute indicates the priority at which data is transferred to the network. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 indices from 0 to 15. Each transfer priority n, where n indicates the transfer priority index, contains a default setting for routing class of service (multimedia, delay or throughput) and FR egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..15  

frUniDlciTransferPriFromNwk 1.1.562.2.4.1.71.5.14.1.11
This attribute indicates the priority at which data is transferred from the network. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 indices from 0 to 15. Each transfer priority n, where n specifies the transfer priority index, contains a default setting for routing class of service (multimedia, delay or throughput) and FR egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..15  

frUniDlciStatsTable 1.1.562.2.4.1.71.5.15
This group contains the operational statistics for the Frame Relay Data Link Connection Identifier.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciStatsEntry

frUniDlciStatsEntry 1.1.562.2.4.1.71.5.15.1
An entry in the frUniDlciStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciStatsEntry  

frUniDlciFrmToIf 1.1.562.2.4.1.71.5.15.1.1
This attribute counts the frames sent out the interface. When the maximum count is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciFecnFrmToIf 1.1.562.2.4.1.71.5.15.1.2
This attribute counts the frames sent to the interface with the Forward Explicit Congestion Notification (FECN) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciBecnFrmToIf 1.1.562.2.4.1.71.5.15.1.3
This attribute counts the frames sent to the interface with the Backward Explicit Congestion Notification (BECN) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciBciToSubnet 1.1.562.2.4.1.71.5.15.1.4
This attribute counts the frames sent into the network with the Backward Congestion Indication (BCI) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDeFrmToIf 1.1.562.2.4.1.71.5.15.1.5
This attribute counts the frames sent to the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDiscCongestedToIf 1.1.562.2.4.1.71.5.15.1.6
This attribute counts the number of frame discards at the Frame Relay service due to local congestion in the direction toward the interface. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDiscDeCongestedToIf 1.1.562.2.4.1.71.5.15.1.7
This attribute counts the number of discarded frames, with the Discard Eligibility (DE) bit set, at the Frame Relay service, due to local congestion in the direction toward the interface. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciFrmFromIf 1.1.562.2.4.1.71.5.15.1.8
This attribute counts the frames received from the interface. It includes the frames that are discarded due to error or excess. When the maximum count is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciFecnFrmFromIf 1.1.562.2.4.1.71.5.15.1.9
This attribute counts the frames received from the interface with the Forward Explicit Congestion Notification (FECN) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciBecnFrmFromIf 1.1.562.2.4.1.71.5.15.1.10
This attribute counts the frames received from the interface with the Backward Explicit Congestion Notification (BECN) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciFciFromSubnet 1.1.562.2.4.1.71.5.15.1.11
This attribute counts the frames received from the network with the Forward Congestion Indication (FCI) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciBciFromSubnet 1.1.562.2.4.1.71.5.15.1.12
This attribute counts the frames received from the network with the Backward Congestion Indication (BCI) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDeFrmFromIf 1.1.562.2.4.1.71.5.15.1.13
This attribute counts the frames received from the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciExcessFrmFromIf 1.1.562.2.4.1.71.5.15.1.14
This attribute counts the frames received from the interface with the Discard Eligibility (DE) bit clear, but subsequently set by the network due to rate enforcement. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDiscExcessFromIf 1.1.562.2.4.1.71.5.15.1.15
This attribute counts the frames which were discarded due to rate enforcement. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDiscFrameAbit 1.1.562.2.4.1.71.5.15.1.16
This attribute counts the number of frame discards at the Frame Relay Service, due to an inactive PVC status, in the direction toward the network. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDiscCongestedFromIf 1.1.562.2.4.1.71.5.15.1.17
This attribute counts the number of frame discards at the Frame Relay service due to local congestion in the direction toward the network. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDiscDeCongestedFromIf 1.1.562.2.4.1.71.5.15.1.18
This attribute counts the number of discarded frames, with the Discard Eligibility (DE) bit set, at the Frame Relay service, due to local congestion, in the direction toward the network. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciErrorShortFrmFromIf 1.1.562.2.4.1.71.5.15.1.19
This attribute counts the frames received with 0 octets in the information field. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciErrorLongFrmFromIf 1.1.562.2.4.1.71.5.15.1.20
This attribute counts the frames received with number of octets in the information field greater than the subscribed maximum. When the count reaches maximum it wraps to zero. Frames whose lengths are greater than the hardware receive buffer are ignored by the hardware and are therefore not included in this count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciBecnFrmSetByService 1.1.562.2.4.1.71.5.15.1.21
This attribute counts the number of frames with BECN set by the Frame Relay service. It is incremented whenever the Frame Relay service sets BECN on a frame upon detecting local congestion. This count is incremented regardless of whether the frame already bears a set BECN bit since its use is to determine the place of congestion. When the count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciBytesToIf 1.1.562.2.4.1.71.5.15.1.22
This attribute counts the bytes sent out the interface. When the maximum count is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDeBytesToIf 1.1.562.2.4.1.71.5.15.1.23
This attribute counts the bytes sent to the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDiscCongestedToIfBytes 1.1.562.2.4.1.71.5.15.1.24
This attribute counts the number of byte discards at the Frame Relay service due to local congestion in the direction toward the link. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDiscDeCongestedToIfBytes 1.1.562.2.4.1.71.5.15.1.25
This attribute counts the number of discard eligible (DE=1) byte discards at the Frame Relay service due to local congestion in the direction toward the link. When the maximum count is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciBytesFromIf 1.1.562.2.4.1.71.5.15.1.26
This attribute counts the bytes received from the interface. Bytes that are discarded due to error or excess are not counted. When the maximum count is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDeBytesFromIf 1.1.562.2.4.1.71.5.15.1.27
This attribute counts the bytes received from the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciExcessBytesFromIf 1.1.562.2.4.1.71.5.15.1.28
This attribute counts the bytes received from the interface with the Discard Eligibility (DE) bit clear, but subsequently set by the network due to rate enforcement. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDiscExcessFromIfBytes 1.1.562.2.4.1.71.5.15.1.29
This attribute counts the bytes which were discarded due to rate enforcement. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDiscByteAbit 1.1.562.2.4.1.71.5.15.1.30
This attribute counts the bytes which were discarded due to aBit turned off.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDiscCongestedFromIfBytes 1.1.562.2.4.1.71.5.15.1.31
This attribute counts the number of byte discards at the Frame Relay service due to local congestion in the direction toward the network. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDiscDeCongestedFromIfBytes 1.1.562.2.4.1.71.5.15.1.32
This attribute counts the number of discard eligible (DE=1) byte discards at the Frame Relay service due to local congestion in the direction toward the network. When the maximum count is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciErrorShortBytesFromIf 1.1.562.2.4.1.71.5.15.1.33
This attribute counts the bytes received with 0 octets in the information field. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciErrorLongBytesFromIf 1.1.562.2.4.1.71.5.15.1.34
This attribute counts the bytes received with number of octets in the information field greater than the subscribed maximum. When the count reaches maximum it wraps to zero. Bytes whose lengths are greater than the hardware receive buffer are ignored by the hardware and are therefore not included in this count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciRateAdaptReduct 1.1.562.2.4.1.71.5.15.1.35
This attribute counts the number of rate reductions due to rate adaptation. Rate adaptation causes the allowed rate to be reduced in steps. After each reduction, a period of time is awaited before further action is taken. At the end of this period, the allowed rate is further reduced if congestion is still prevalent. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciRateAdaptReductPeriod 1.1.562.2.4.1.71.5.15.1.36
This attribute provides a cumulative count of the amount of time that rate adaptation procedures have been in effect. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciTransferPriorityToNetwork 1.1.562.2.4.1.71.5.15.1.37
This attribute is obsolete. It is replaced by attribute transferPriorityToNetwork under group FrsNniDataLinkConnectionIdentifierServiceParametersOp.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15)  

frUniDlciTransferPriorityFromNetwork 1.1.562.2.4.1.71.5.15.1.38
This attribute is obsolete. It is replaced by attribute transferPriorityToNetwork under group FrsNniDataLinkConnectionIdentifierServiceParametersOp.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15)  

frUniDlciCirPresent 1.1.562.2.4.1.71.5.15.1.39
This attribute provides the actual Committed Information Rate (CIR) enforced for this DLCI. This number is in units of 800 bits/ sec, since that is the internal resolution of Passport rate enforcement. If rateEnforcement is off, then this number does not have meaning. Normally, this attribute matches the provisioned CIR for the DLCI. But when Rate Adaptation is active, then this number will vary to represent the actual Allowed CIR at the moment that this attribute is collected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciEirPresent 1.1.562.2.4.1.71.5.15.1.40
This attribute provides the actual Excess Information Rate (EIR) enforced for this DLCI. This number is in units of 800 bits/sec, since that is the internal resolution of Passport rate enforcement. If rateEnforcement is off, then this number does not have meaning. Normally, this attribute matches the provisioned EIR for the DLCI. But when Rate Adaptation is active, then this number will vary to represent the actual Allowed EIR at the moment that this attribute is collected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciIntTable 1.1.562.2.4.1.71.5.16
This group contains the operational statistics for the Frame Relay Data Link Connection Identifier interval data.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciIntEntry

frUniDlciIntEntry 1.1.562.2.4.1.71.5.16.1
An entry in the frUniDlciIntTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciIntEntry  

frUniDlciStartTime 1.1.562.2.4.1.71.5.16.1.1
This attribute displays the start time of this interval period. If Vc spans 12 hour time or time of day change startTime reflects new time as recorded at 12 hour periods or time of day changes. A new interval period is started each time an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  EnterpriseDateAndTime Size(0|19)  

frUniDlciTotalIngressBytes 1.1.562.2.4.1.71.5.16.1.2
This attribute counts the total bytes received from the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned64 Size(8)  

frUniDlciTotalEgressBytes 1.1.562.2.4.1.71.5.16.1.3
This attribute counts the total bytes sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned64 Size(8)  

frUniDlciEirIngressBytes 1.1.562.2.4.1.71.5.16.1.4
This attribute counts the total bytes with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned64 Size(8)  

frUniDlciEirEgressBytes 1.1.562.2.4.1.71.5.16.1.5
This attribute counts the total bytes with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned64 Size(8)  

frUniDlciDiscardedBytes 1.1.562.2.4.1.71.5.16.1.6
This attribute counts the total bytes in invalid frames received from the interface and discarded at the DLCI since the start of the interval period. This count is a sum of octets in frames discarded due to the number of octets in the information field greater than the subscribed maximum or equal to 0, due to aBit turned off, or due to rate enforcement. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned64 Size(8)  

frUniDlciTotalIngressSegFrm 1.1.562.2.4.1.71.5.16.1.7
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the total number of segments in frames received from the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the total number of frames received from the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciTotalEgressSegFrm 1.1.562.2.4.1.71.5.16.1.8
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the total number of segments in frames sent to the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the total number of frames sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciEirIngressSegFrm 1.1.562.2.4.1.71.5.16.1.9
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in frames with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of frames with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciEirEgressSegFrm 1.1.562.2.4.1.71.5.16.1.10
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in frames with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of frames with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDiscardedSegFrm 1.1.562.2.4.1.71.5.16.1.11
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in invalid frames received from the interface and discarded at the DLCI. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of invalid frames received from the interface and discarded at the DLCI. Segments of frames are counted since the start of the interval period. The count is reset to zero when an accounting record is generated. The count is a sum of segments in frames or frames discarded due to the number of octets in the information field greater than the subscribed maximum or equal to 0, due to aBit turned off, or due to rate enforcement.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciCirPresentObs 1.1.562.2.4.1.71.5.16.1.12
This attribute has moved to the statistics subgroup. See cirPresent.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciEirPresentObs 1.1.562.2.4.1.71.5.16.1.13
This attribute has moved to the statistics subgroup. See eirPresent.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciRateEnforcementPresent 1.1.562.2.4.1.71.5.16.1.14
This attribute is obsolete. It is the same as the provisioned rateEnforcement attribute.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

frUniDlciRateAdaptationPresent 1.1.562.2.4.1.71.5.16.1.15
This attribute is obsolete. See the provisioning attribute rateAdaptation for the data that it intended to provide.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

frUniDlciLocalRateAdaptOccurred 1.1.562.2.4.1.71.5.16.1.16
This attribute specifies whether rate adaptation has occurred on this user Data Link Connection on this Frame Relay interface.The count is reset to 0 when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..1  

frUniDlciCallReferenceNumber 1.1.562.2.4.1.71.5.16.1.17
This attribute displays the call reference number which is a unique number generated by the switch.The same Call Reference Number is stored in the interval data (accounting record) at both ends of the call. It can be used as one of the attributes in matching duplicate records generated at each end of the call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciElapsedDifference 1.1.562.2.4.1.71.5.16.1.18
This attribute displays the elapsed time representing the period of this interval data. It is elapsed time in 0.1 second increments since the call started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciDc 1.1.562.2.4.1.71.5.2
OBJECT IDENTIFIER    

frUniDlciDcRowStatusTable 1.1.562.2.4.1.71.5.2.1
This entry controls the addition and deletion of frUniDlciDc components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciDcRowStatusEntry

frUniDlciDcRowStatusEntry 1.1.562.2.4.1.71.5.2.1.1
A single entry in the table represents a single frUniDlciDc component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciDcRowStatusEntry  

frUniDlciDcRowStatus 1.1.562.2.4.1.71.5.2.1.1.1
This variable is used as the basis for SNMP naming of frUniDlciDc components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

frUniDlciDcComponentName 1.1.562.2.4.1.71.5.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniDlciDcStorageType 1.1.562.2.4.1.71.5.2.1.1.4
This variable represents the storage type value for the frUniDlciDc tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniDlciDcIndex 1.1.562.2.4.1.71.5.2.1.1.10
This variable represents the index for the frUniDlciDc tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frUniDlciDcOptionsTable 1.1.562.2.4.1.71.5.2.10
Options group defines attributes associated with direct call. It defines complete connection in terms of path and call options. This connection can be permanent (pvc) or switched (svc). It can have facilities. The total number of bytes of facilities including the facility codes, and all of the facility data from all of the four classes of facilities: CCITT_Facilities DTE_Facilities National_Facilities International_Facilities must not exceed 512 bytes.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciDcOptionsEntry

frUniDlciDcOptionsEntry 1.1.562.2.4.1.71.5.2.10.1
An entry in the frUniDlciDcOptionsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciDcOptionsEntry  

frUniDlciDcRemoteNpi 1.1.562.2.4.1.71.5.2.10.1.3
Destination Numbering Plan Indicator (Npi) indicates the numbering plan used in the remoteDna.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

frUniDlciDcRemoteDna 1.1.562.2.4.1.71.5.2.10.1.4
This attribute specifies the Data Network Address (DNA) of the remote. This is the called (destination) DTE address (DNA) to which this direct call will be sent. Initially, the called DTE address attribute must be present, that is, there must be a valid destination address. However, it may be possible in the future to configure the direct call with a mnemonic address, in which case, this attribute will contain a zero-length DNA, and the mnemonic address will be carried as one of the facilities.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DigitString Size(1..15)  

frUniDlciDcRemoteDlci 1.1.562.2.4.1.71.5.2.10.1.5
L(LCN) of the destination. This attribute provides the remote LCN (Logical Channel Number) - it is used only for PVCs, where the parameter Type is set to a value of PVC.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 16..1007  

frUniDlciDcType 1.1.562.2.4.1.71.5.2.10.1.6
This attribute specifies the type of Vc call: permanentMaster, permanentSlave, permanentSlaveWithBackup, permanentBackupSlave. If the value is set to permanentMaster, then a permanent connection will be established between 2 ends. The remote end must be defined as a permanentSlave, permanentBackupSlave or permanentSlaveWithBackup. The Connection cannot be established if the remote end is defined as anything else. The end defined as permanentMaster always initiates the calls. It will attempt to call once per minute. If the value is set to permanentSlave then a permanent connection will be established between 2 ends. The remote end must be defined as a permanentMaster. The Connection cannot be established if the remote end is defined as anything else. The permanentSlave end will attempt to call once per minute. If the value is set to permanentSlaveWithBackup then a permanent connection will be established between the two ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote interface end is defined as anything else. The permanentSlaveWithBackup end will attempt to call once per minute. When type is set to permanentSlaveWithBackup connection will be cleared if interface becomes unavailable. This enables a retry of the connection which can be redirected to permanentBackupSlave. If the value is set to permanentBackupSlave then a permanent connection will be established between the 2 ends only if the permanentMaster end is disconnected from the permanentSlaveWithBackup end and a backup call is established by the redirection system. If the permanentSlaveWithBackup interface becomes visible again, the permanentBackupSlave end is disconnected and the permanentSlaveWithBackup end is reconnected to the permanentMaster end. The permanentBackupSlave end does not try to establish pvc call.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER permanentMaster(1), permanentSlave(2), permanentBackupSlave(3), permanentSlaveWithBackup(4)  

frUniDlciDcTransferPriority 1.1.562.2.4.1.71.5.2.10.1.9
This attribute specifies the transfer priority to network for the outgoing calls using this particular DLCI. It overRides the defaultTransferPriority provisioned in its associated Dna component. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 levels from 0 to 15. Each transfer priority n, where n is the transfer priority index, contains a default setting for routing class of service (multimedia, delay or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned under the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required. The default of transferPriority is useDnaDefTP. It means using the provisioning value under defaultTransferPriority of its associated Dna for this DLCI.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15), useDnaDefTP(255)  

frUniDlciDcDiscardPriority 1.1.562.2.4.1.71.5.2.10.1.10
This attribute specifies the discard priority for outgoing call using this DLCI. The discard priority has three provisioning values: normal, high, and useDnaDefPriority. Traffic with normal priority are discarded first than the traffic with high priority. The Dna default value (provisioned by outDefaultPriority) is taken if this attribute is set to the value useDnaDefPriority. The default of discardPriority is useDnaDefPriority.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER normal(0), high(1), useDnaDefPriority(3)  

frUniDlciDcDeDiscardPriority 1.1.562.2.4.1.71.5.2.10.1.11
This attribute specifies whether the discardPriority applies to DE frames for this DLCI. If deDiscardPriority is set to determinedByDiscardPriority, traffic with DE bit set will be discarded according to the setting of the discardPriority. If deDiscardPriority is set to lowest, all traffic with DE bit set will be treated the same and be sent to the subnet at the lowest discard priority.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER lowest(0), determinedByDiscardPriority(1)  

frUniDlciDcDataPath 1.1.562.2.4.1.71.5.2.10.1.12
This attribute specifies the data path to be used by Virtual Circuits on this interface. The value of the dataPath attribute in the Dna component is overridden by this attribute if the value is not useDnaValue. This value applies to the connection after data transfer state is reached. All the data and control trafic will be sent using this data path. If the provisioned dataPath is not available the connection is not established. The value of the dataPath is signalled by both ends of the connection. If this value is not the same at both ends dprsOnly is used for the duration of the connection. A virtual circuit connection is always established using dprsOnly even if this attribute is provisioned as some other value. dprsOnly - dynamic packet routing system is used dprsMcsOnly - dprs Multi-Service Cut-Through Switching path is used. dprsMcsFirst - dprs Multi-Service Cut-Through Switching path is used if it is available. If it is not avaliable dprsOnly is used. useDnaValue - use the value provisioned in Dna component.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dprsOnly(0), dprsMcsOnly(1), dprsMcsFirst(2), useDnaValue(3)  

frUniDlciDcCugIndex 1.1.562.2.4.1.71.5.2.10.1.13
This attribute specifies the CUG index which is to be signalled in PVC call requests to the remote end. The type of CUG signalling is defined in attribute cugType in this component.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

frUniDlciDcCugType 1.1.562.2.4.1.71.5.2.10.1.14
This attribute specifies the type of CUG signalling to be used in PVC call request. Index of CUG to be used is defined in attribute cugIndex in this component. Possible values are: cug - signal cug cugOa - signal cug with outgoing access doNotSignal - no CUG in call request
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER doNotSignal(0), cug(3), cugOa(9)  

frUniDlciDcNfaTable 1.1.562.2.4.1.71.5.2.202
This is the i'th National facility required for this direct call. Within the provisioning system, the user specifies the facility code along with the facility parameters. The facility is represented internally as a hexadecimal string following the X.25 CCITT representation for facility data. Two explicit attributes discardPriority and pathSensitivity are created to replace H.01 and H.30 in the group VcsDirectCallOptionsProv of this file. The migrate escape here (DcComponent::migrateFaxEscape) propagates the old provisioning data under H.01 and H.30 into discardPriority and transferPriority. The rule of the above propagation are: 0 in H.01 is equivalent to discardPriority 0; 1 in H.01 is equivalent to discardPriority 1. And 0 in H.30 is equivalent to transferPriority throughput; 1 in H.30 is equivalent to pathSensitivity delay. Please refer to discardPriority and pathSensitivity for more information on how to use them.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciDcNfaEntry

frUniDlciDcNfaEntry 1.1.562.2.4.1.71.5.2.202.1
An entry in the frUniDlciDcNfaTable.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  FrUniDlciDcNfaEntry  

frUniDlciDcNfaIndex 1.1.562.2.4.1.71.5.2.202.1.1
This variable represents the index for the frUniDlciDcNfaTable.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1 | 48  

frUniDlciDcNfaValue 1.1.562.2.4.1.71.5.2.202.1.2
This variable represents an individual value for the frUniDlciDcNfaTable.
Status: obsolete Access: read-write
OBJECT-TYPE    
  HexString Size(0..128)  

frUniDlciDcNfaRowStatus 1.1.562.2.4.1.71.5.2.202.1.3
This variable is used to control the addition and deletion of individual values of the frUniDlciDcNfaTable.
Status: obsolete Access: write-only
OBJECT-TYPE    
  RowStatus  

frUniDlciVc 1.1.562.2.4.1.71.5.3
OBJECT IDENTIFIER    

frUniDlciVcRowStatusTable 1.1.562.2.4.1.71.5.3.1
This entry controls the addition and deletion of frUniDlciVc components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciVcRowStatusEntry

frUniDlciVcRowStatusEntry 1.1.562.2.4.1.71.5.3.1.1
A single entry in the table represents a single frUniDlciVc component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciVcRowStatusEntry  

frUniDlciVcRowStatus 1.1.562.2.4.1.71.5.3.1.1.1
This variable is used as the basis for SNMP naming of frUniDlciVc components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

frUniDlciVcComponentName 1.1.562.2.4.1.71.5.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniDlciVcStorageType 1.1.562.2.4.1.71.5.3.1.1.4
This variable represents the storage type value for the frUniDlciVc tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniDlciVcIndex 1.1.562.2.4.1.71.5.3.1.1.10
This variable represents the index for the frUniDlciVc tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frUniDlciVcCadTable 1.1.562.2.4.1.71.5.3.10
This group represents operational call data related to Frame Relay Vc. It can be displayed only for Frame Relay Vc which is created by application.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciVcCadEntry

frUniDlciVcCadEntry 1.1.562.2.4.1.71.5.3.10.1
An entry in the frUniDlciVcCadTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciVcCadEntry  

frUniDlciVcType 1.1.562.2.4.1.71.5.3.10.1.1
This attribute displays the type of call, pvc,svc or spvc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER svc(0), pvc(1), spvc(2)  

frUniDlciVcState 1.1.562.2.4.1.71.5.3.10.1.2
This attribute displays the state of call control. P5 state is not supported but is listed for completness. Transitions from one state to another take very short time. state most often displayed is dataTransferP4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER creating(0), readyP1(1), dteWaitingP2(2), dceWaitingP3(3), dataTransferP4(4), unsupportedP5(5), dteClearRequestP6(6), dceClearIndicationP7(7), termination(8)  

frUniDlciVcPreviousState 1.1.562.2.4.1.71.5.3.10.1.3
This attribute displays the previous state of call control. This is a valuable field to determine how the processing is progressing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER creating(0), readyP1(1), dteWaitingP2(2), dceWaitingP3(3), dataTransferP4(4), unsupportedP5(5), dteClearRequestP6(6), dceClearIndicationP7(7), termination(8)  

frUniDlciVcDiagnosticCode 1.1.562.2.4.1.71.5.3.10.1.4
This attribute displays the internal substate of call control. It is used to further refine state of call processing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

frUniDlciVcPreviousDiagnosticCode 1.1.562.2.4.1.71.5.3.10.1.5
This attribute displays the internal substate of call control. It is used to further refine state of call processing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

frUniDlciVcCalledNpi 1.1.562.2.4.1.71.5.3.10.1.6
This attribute displays the Numbering Plan Indicator (NPI) of the called end.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

frUniDlciVcCalledDna 1.1.562.2.4.1.71.5.3.10.1.7
This attribute displays the Data Network Address (Dna) of the called (destination) DTE to which this call is sent. This address if defined at recieving end will complete Vc connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DigitString Size(1..15)  

frUniDlciVcCalledLcn 1.1.562.2.4.1.71.5.3.10.1.8
This attribute displays the Logical Channel Number of the called end. It is valid only after both ends of Vc exchanged relevant information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 1..65535  

frUniDlciVcCallingNpi 1.1.562.2.4.1.71.5.3.10.1.9
This attribute displays the Numbering Plan Indicator (NPI) of the calling end.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

frUniDlciVcCallingDna 1.1.562.2.4.1.71.5.3.10.1.10
This attribute displays the Data Network Address (Dna) of the calling end.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DigitString Size(1..15)  

frUniDlciVcCallingLcn 1.1.562.2.4.1.71.5.3.10.1.11
This attribute displays the Logical Channel Number of the calling end.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 1..65535  

frUniDlciVcAccountingEnabled 1.1.562.2.4.1.71.5.3.10.1.12
This attribute indicates that this optional section of accounting record is suppressed or permitted. If accountingEnabled is yes, conditions for generation of accounting record were met. These conditions include billing options, vc recovery conditions and Module wide accounting data options.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(0), no(1)  

frUniDlciVcFastSelectCall 1.1.562.2.4.1.71.5.3.10.1.13
This attribute displays that this is a fast select call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

frUniDlciVcPathReliability 1.1.562.2.4.1.71.5.3.10.1.19
This attribute displays the path reliability.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER high(0), normal(1)  

frUniDlciVcAccountingEnd 1.1.562.2.4.1.71.5.3.10.1.20
This attribute indicates if this end should generate an accounting record. Normally, callingEnd is the end to generate an accounting record.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER callingEnd(0), calledEnd(1)  

frUniDlciVcPriority 1.1.562.2.4.1.71.5.3.10.1.21
This attribute displays whether the call is a normal or a high priority call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(0), high(1)  

frUniDlciVcSegmentSize 1.1.562.2.4.1.71.5.3.10.1.22
This attribute displays the segment size (in bytes) used on the call. It is used to calculate the number of segments transmitted and received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4096  

frUniDlciVcMaxSubnetPktSize 1.1.562.2.4.1.71.5.3.10.1.27
This attribute indicates the maximum packet size allowed on the Vc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4096  

frUniDlciVcRcosToNetwork 1.1.562.2.4.1.71.5.3.10.1.28
This attribute indicates the routing metric routing class of service to the network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER throughput(0), delay(1), multimedia(2)  

frUniDlciVcRcosFromNetwork 1.1.562.2.4.1.71.5.3.10.1.29
This attribute displays the routing metric Routing Class of Service from the Network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER throughput(0), delay(1), multimedia(2)  

frUniDlciVcEmissionPriorityToNetwork 1.1.562.2.4.1.71.5.3.10.1.30
This attribute displays the network internal emission priotity to the network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(0), high(1), interrupting(2)  

frUniDlciVcEmissionPriorityFromNetwork 1.1.562.2.4.1.71.5.3.10.1.31
This attribute displays the network internal emission priotity from the network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(0), high(1), interrupting(2)  

frUniDlciVcDataPath 1.1.562.2.4.1.71.5.3.10.1.32
This attribute indicates the data path used by the connection. The data path is provisioned in Dna and DirectCall components. The displayed value of this attribute can be different from the provisioned value. If the connection is using dprsOnly data path, the string dprsOnly is displayed. (dynamic packet routing system) If the connection is using dprsMcsOnly data path, the string dprsMcsOnly is displayed. If the connection is using dprsMcsFirst data path, the string dprsMcsFirst is displayed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(0..32)  

frUniDlciVcIntdTable 1.1.562.2.4.1.71.5.3.11
This group defines display of interval data collected by Vc. Data in this group is variable and may depend on time when this display command is issued.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciVcIntdEntry

frUniDlciVcIntdEntry 1.1.562.2.4.1.71.5.3.11.1
An entry in the frUniDlciVcIntdTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciVcIntdEntry  

frUniDlciVcCallReferenceNumber 1.1.562.2.4.1.71.5.3.11.1.1
This attribute displays the call reference number which is a unique number generated by the switch.The same Call Reference Number is stored in the interval data (accounting record) at both ends of the call. It can be used as one of the attributes in matching duplicate records generated at each end of the call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Hex 0..16777215  

frUniDlciVcElapsedTimeTillNow 1.1.562.2.4.1.71.5.3.11.1.2
This attribute displays the elapsed time representing the period of this interval data. It is elapsed time in 0.1 second increments since Vc started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..16777215  

frUniDlciVcSegmentsRx 1.1.562.2.4.1.71.5.3.11.1.3
This attribute displays the number of segments received at the time command was issued. This is the segment received count maintained by accounting at each end of the Vc. This counter is updated only when the packet cannot be successfully delivered out of the sink Vc and to the sink AP Conditions in which packets may be discarded by the sink Vc include: missing packets due to subnet discards, segmentation protocol violations due to subnet discard, duplicated and out-of-ranged packets and packets that arrive while Vc is in path recovery state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..16777215  

frUniDlciVcSegmentsSent 1.1.562.2.4.1.71.5.3.11.1.4
This attribute displays the number of segments sent at the time command was issued. This is the segment sent count maintained by accounting at the source Vc. Vc only counts packets that Vc thinks can be delivered successfully into the subnet. In reality, these packets may be dropped by trunking, for instance. This counter is not updated when splitting fails, when Vc is in a path recovery state, when packet forwarding fails to forward this packet and when subsequent packets have to be discarded as we want to minimize the chance of out-of-sequence and do not intentionally send out-of- sequenced packets into the subnet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..16777215  

frUniDlciVcStartTime 1.1.562.2.4.1.71.5.3.11.1.5
This attribute displays the start time of this interval period. If Vc spans 12 hour time or time of day change startTime reflects new time as recorded at 12 hour periods or time of day changes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  EnterpriseDateAndTime Size(0|19)  

frUniDlciVcFrdTable 1.1.562.2.4.1.71.5.3.12
This group defines Frame Relay attributes collected by Frame Relay Vc. The purpose of Vc attributes is to aid end users and verification people to understand the Vc internal behavior. This is particularly useful when the network has experienced abnormality and we want to isolate problems and pinpoint trouble spots. Attributes are collected on a per Vc basis. Until a need is identified, statistics are not collected at a processor level. Each attribute is stored in a 32 bit field and is initialized to zero when a Vc enters into the data transfer state. When a PVC is disconnected and then connected again, the attributes will be reset. Attributes cannot be reset through other methods. Frame Relay Vc uses a best effort data packet delivery protocol and a different packet segmentation and combination methods from the General Vc. The Frame Relay Vc uses the same call setup and control mechanism (e.g. the support of non-flow control data packets) as in a General Vc. Most General Vc statistics and internal variables are used in a Frame Relay Vc and are displayed by software developers
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciVcFrdEntry

frUniDlciVcFrdEntry 1.1.562.2.4.1.71.5.3.12.1
An entry in the frUniDlciVcFrdTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciVcFrdEntry  

frUniDlciVcFrmCongestedToSubnet 1.1.562.2.4.1.71.5.3.12.1.2
This attribute displays the number of frames from link discarded due to lack of resources. It keeps track of the number of frames from link that have to be discarded. The discard reasons include insufficient memory for splitting the frame into smaller subnet packet size.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcCannotForwardToSubnet 1.1.562.2.4.1.71.5.3.12.1.3
This attribute displays the number of discarded packets that can not be forwarded into the subnet because of subnet congestion. Number of frames from link discarded due to failure in forwarding a packet from Vc into the subnet.- This attribute is increased when packet forwarding fails to forward a packet into the subnet. If a frame is split into multiple subnet packets and a partial packet has to be discarded, all subsequent partial packets that have not yet been delivered to the subnet will be discarded as well.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcNotDataXferToSubnet 1.1.562.2.4.1.71.5.3.12.1.4
This attribute records the number of frames from link discarded when the Vc tries to recover from internal path failure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcOutOfRangeFrmFromSubnet 1.1.562.2.4.1.71.5.3.12.1.5
This attribute displays the number of frames from subnet discarded due to out of sequence range for arriving too late.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcCombErrorsFromSubnet 1.1.562.2.4.1.71.5.3.12.1.6
This attribute records the number of subnet packets discarded at the sink Vc due to the Vc segmentation and combination protocol error. Usually, this occurs when the subnet discards packets and thus this statistics can be used to guest the number of subnet packets that are not delivered to the Vc. It cannot be used as an actual measure because some subnet packets may have been delivered to Vc but have to be discarded because these are partial packets to a frame in which some other partial packets have not been properly delivered to Vc
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcDuplicatesFromSubnet 1.1.562.2.4.1.71.5.3.12.1.7
This attribute displays the number of subnet packets discarded due to duplication. Although packets are not retransmitted by the Frame Relay Vc, it is possible for the subnet to retransmit packets. When packets are out-of-sequenced and copies of the same packets arrive, then this attribute is increased.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcNotDataXferFromSubnet 1.1.562.2.4.1.71.5.3.12.1.8
This attribute displays the number of subnet packets discarded when data transfer is suspended in Vc recovery.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcFrmLossTimeouts 1.1.562.2.4.1.71.5.3.12.1.9
This attribute displays the number of lost frame timer expiries. When this count is excessive, the network is very congested and packets have been discarded in the subnet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcOoSeqByteCntExceeded 1.1.562.2.4.1.71.5.3.12.1.10
This attribute displays the number times that the out of sequence byte threshold is exceeded. When the threshold is exceeded, this condition is treated as if the loss frame timer has expired and all frames queued at the sink Vc are delivered to the AP. We need to keep this count to examine if the threshold is engineered properly. This should be used in conjunction with the peak value of out-of- sequenced queue and the number of times the loss frame timer has expired. This count should be relatively small when compared with loss frame timer expiry count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcPeakOoSeqPktCount 1.1.562.2.4.1.71.5.3.12.1.11
This attribute displays the frame relay peak packet count of the out of sequence queue. This attribute records the maximum queue length of the out-of-sequenced queue. The counter can be used to deduce the message buffer requirement on a Vc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcPeakOoSeqFrmForwarded 1.1.562.2.4.1.71.5.3.12.1.12
This attribute displays the frame relay peak size of the sequence packet queue. The subnet may deliver packets out-of- sequenced. These packets are then queued in an out-of-sequenced queue, waiting for a packet with the expected sequence number to come. When that packet arrives, this attribute records the maximum number of packets that were out-of-sequenced, but now have become in-sequenced. The statistics is used to measure expected queue size due to normal subnet packet disorder (not due to subnet packet discard). Current implementation also uses this statistics to set a maximum size for the out-of-sequenced queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcSendSequenceNumber 1.1.562.2.4.1.71.5.3.12.1.13
This attribute displays the Vc internal packet's send sequence number. Note that a 'packet' in this context, may be either a user data packet, or an OAM frame.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcPktRetryTimeouts 1.1.562.2.4.1.71.5.3.12.1.15
This attribute displays the number of packets which have retransmission time-outs. When this count is excessive, the network is very congested and packets have been discarded in the subnet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcPeakRetryQueueSize 1.1.562.2.4.1.71.5.3.12.1.16
This attribute displays the peak size of retransmission queue. This attribute is used as an indicator of the acknowledgment behavior across the subnet. Records the largest body of unacknowledged packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcSubnetRecoveries 1.1.562.2.4.1.71.5.3.12.1.17
This attribute displays the number of successful Vc recovery attempts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

frUniDlciVcOoSeqPktCntExceeded 1.1.562.2.4.1.71.5.3.12.1.19
This attribute displays the number times that the out of sequence packet threshold is exceeded. When the threshold is exceeded, this condition is treated as if the loss frame timer has expired and all frames queued at the sink Vc are delivered to the AP. We need to keep this count to examine if the threshold is engineered properly. This should be used in conjunction with the peak value of out-of- sequenced queue and the number of times the loss frame timer has expired. This count should be relatively small when compared with loss frame timer expiry count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

frUniDlciVcPeakOoSeqByteCount 1.1.562.2.4.1.71.5.3.12.1.20
This attribute displays the frame relay peak byte count of the out of sequence queue. This attribute records the maximum queue length of the out-of-sequenced queue. The counter can be used to deduce the message buffer requirement on a Vc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..50000  

frUniDlciVcDmepTable 1.1.562.2.4.1.71.5.3.417
This attribute displays the data path used by the connection. Data path is provisioned in Dna and DirectCall components. If the connection is using dprsOnly data path, this attribute is empty. If the connection is using dprsMcsOnly or dprsMcsFirst data path, this attribute displays component name of the dprsMcsEndPoint.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciVcDmepEntry

frUniDlciVcDmepEntry 1.1.562.2.4.1.71.5.3.417.1
An entry in the frUniDlciVcDmepTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciVcDmepEntry  

frUniDlciVcDmepValue 1.1.562.2.4.1.71.5.3.417.1.1
This variable represents both the value and the index for the frUniDlciVcDmepTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowPointer  

frUniDlciSp 1.1.562.2.4.1.71.5.4
OBJECT IDENTIFIER    

frUniDlciSpRowStatusTable 1.1.562.2.4.1.71.5.4.1
This entry controls the addition and deletion of frUniDlciSp components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciSpRowStatusEntry

frUniDlciSpRowStatusEntry 1.1.562.2.4.1.71.5.4.1.1
A single entry in the table represents a single frUniDlciSp component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciSpRowStatusEntry  

frUniDlciSpRowStatus 1.1.562.2.4.1.71.5.4.1.1.1
This variable is used as the basis for SNMP naming of frUniDlciSp components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

frUniDlciSpComponentName 1.1.562.2.4.1.71.5.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniDlciSpStorageType 1.1.562.2.4.1.71.5.4.1.1.4
This variable represents the storage type value for the frUniDlciSp tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniDlciSpIndex 1.1.562.2.4.1.71.5.4.1.1.10
This variable represents the index for the frUniDlciSp tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frUniDlciSpParmsTable 1.1.562.2.4.1.71.5.4.11
This group contains the provisionable attributes for the Data Link Connection Identifier. These attributes reflect the service parameters specific to this instance of DLCI. The congestion control attributes in this group are defined in T1.606 Addendum 1.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciSpParmsEntry

frUniDlciSpParmsEntry 1.1.562.2.4.1.71.5.4.11.1
An entry in the frUniDlciSpParmsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciSpParmsEntry  

frUniDlciSpMaximumFrameSize 1.1.562.2.4.1.71.5.4.11.1.1
This attribute specifies the maximum number of octets which may be included in the information field. The frame relay header and CRC octets are not included in this definition. This attribute corresponds to the dN1 parameter described in the Vendor Forum Specification.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..8187  

frUniDlciSpRateEnforcement 1.1.562.2.4.1.71.5.4.11.1.2
This attribute specifies whether rate enforcement is in effect for this user Data Link Connection on this Frame Relay interface. Turning on rate enforcement means that CIR and DE=1 traffic will be measured and enforced. Turning off rate enforcement means that all frames from the user will be accepted and no modifications to the frame with respect to the DE bit will be made.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

frUniDlciSpCommittedInformationRate 1.1.562.2.4.1.71.5.4.11.1.3
This attribute specifies the committed information rate (CIR) in bits per second (bit/s). When rateEnforcement is set to on, cir is the rate at which the network agrees to transfer information under normal conditions. This rate is measured over a measurement interval (t) that is determined internally based on CIR and the committed burst size (Bc). An exception to this occurs when CIR is provisioned to be zero, in which case the measurement interval (t) must be provisioned explicitly. This attribute is ignored when rateEnforcement is off. If rateEnforcement is on and this attribute is 0, Bc must also be 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge32 0..50000000  

frUniDlciSpCommittedBurstSize 1.1.562.2.4.1.71.5.4.11.1.4
This attribute specifies the committed burst size (Bc) in bits. bc is the amount of data that a network agrees to transfer under normal conditions over a measurement interval (t). Data marked DE=1 is not accounted for in Bc. This attribute is ignored when rateEnforcement is off. If rateEnforcement is on and this attribute is 0, cir must also be 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge32 0..50000000  

frUniDlciSpExcessBurstSize 1.1.562.2.4.1.71.5.4.11.1.5
This attribute specifies the excess burst size (Be) in bits. Be is the amount of uncommitted data that the network will attempt to deliver over measurement interval T. Data marked DE=1 by the user or by the network is accounted for here. CIR, Bc, and Be cannot all be zero when rateEnforcement is on.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge32 0..50000000  

frUniDlciSpMeasurementInterval 1.1.562.2.4.1.71.5.4.11.1.6
When cir and bc are zero and rateEnforcement is on, this attribute must be provisioned to specify the time interval (in milliseconds) over which rates and burst sizes are measured. When cir and bc are non-zero, the time interval is internally calculated and is not shown. In that situation, this field is ignored, and is not representative of the time interval. This attribute is ignored when rateEnforcement is off, or when cir and bc are non-zero. If rateEnforcement is on and both cir and bc are zero, this field must be non-zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..25500  

frUniDlciSpRateAdaptation 1.1.562.2.4.1.71.5.4.11.1.7
This attribute specifies whether rate adaptation is in effect for this user Data Link Connection on this Frame Relay interface. Rate adaptation is a feature that, in periods of congestion, adapts the rate at which the user is allowed to send data into the network to that which the network is able to handle at that time. This pro-active measure of handling congestion optimizes network resources by causing the ingress to discard frames that would otherwise be discarded in the network. If this attribute is set to on, then, at the onset of congestion, the excess information rate (EIR) is reduced to a very low rate. If congestion persists, then the allowed CIR is reduced geometrically by 25% of the current value at that time. The minimum to which CIR can be reduced is 1/16th (6.25%) of the provisioned value. As congestion alleviates, CIR is increased linearly by 6.25% of the provisioned value specified in committedInformationRate. If set to eirOnly, then rate adaptation will only apply to the excess information rate (EIR). At the onset of congestion, the allowed EIR is reduced by 25% of its provisioned value. If congestion persists, EIR is reduced geometrically by 25% of the current value at that time. As congestion alleviates, EIR is gradually increased linearly by 6.25% of the provisioned EIR. If set to cirProportionate, then rate adaptation will also only apply to the excess information rate (EIR). At the onset of congestion the initial allowed EIR is set to a multiple of the provisioned CIR. If congestion persists, the allowed EIR is reduced geometrically by 25% of the current value at that time. As congestion alleviates, EIR is gradually increased linearly by 6.25% of the provisioned EIR. Note that the allowed EIR may be set higher than the provisioned EIR, since it is calculated initially using another parameter, the provisioned CIR. If the allowed EIR at the moment is higher than the provisioned EIR, then the provisioned EIR is used instead. This attribute can only be set to on eirOnly or cirProportionate if rateEnforcement is turned on.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1), eirOnly(2), cirProportionate(3)  

frUniDlciSpAccounting 1.1.562.2.4.1.71.5.4.11.1.8
This attribute specifies whether accounting data collection and record generation is turned on at this DLCI. For accounting data collection and record generation to be turned on, the accountingOn bit and at least one of the accountCollection bits in the DataNetworkAddress component must be set to on.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

frUniDlciSpRaSensitivity 1.1.562.2.4.1.71.5.4.11.1.9
This attribute specifies the sensitivity of the rate adaptation system. A higher number indicates a higher sensitivity and therefore a quicker reaction time to network conditions. A quicker reaction time allows the network to discard frames at the access and protect network resources, but can lead to false alarms and a greater fluctuation of the allowed rate. A higher setting therefore tends to favour the protection of the network over the allowed throughput of the user. A lower number indicates a lower sensitivity and therefore a slower reaction to network conditions. A slower reaction time results in a greater amount of user traffic allowed into the network, but can lead to a waste of network bandwidth since the traffic may be discarded at the congested resource. A lower setting therefore tends to favour the allowed throughput of the user over the protection of the network. This attribute is applicable for adapting EIR when rateAdaptation is eirOnly or cirProportionate, or CIR when rateAdaptation is on. This attribute is ignored if rateAdaptation is turned off.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..20  

frUniDlciSpUpdateBCI 1.1.562.2.4.1.71.5.4.11.1.10
This attribute specifies whether internal Backward Congestion Indication (BCI) bits will report congestion external to the Passport network, as communicated through incoming BECN bits. If updateBCI is set to on, then BCI bits for incoming frames will be set if the BECN on the frame is set. If updatBCI is set to off, then incoming BECN bits will have no effect. Setting updateBCI on for a DLCI means that the remote end of the DLCI, which is specified by the remotedna and remotedlci attributes of the dc component of the dlci, may perform Rate Adaptation using the flow of incoming BECN bits, in addition to internal Passport congestion management systems. If the rateAdaptation attribute of the remote dlci is provisioned as eirOnly, cirProportionate, or on, then congestion from another network connected to a Passport network may trigger dynamic congestion management. If the rateAdaptation attribute of the remote dlci is provisioned to off, then the setting of updateBCI attribute here will have no effect..
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

frUniDlciLb 1.1.562.2.4.1.71.5.5
OBJECT IDENTIFIER    

frUniDlciLbRowStatusTable 1.1.562.2.4.1.71.5.5.1
This entry controls the addition and deletion of frUniDlciLb components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciLbRowStatusEntry

frUniDlciLbRowStatusEntry 1.1.562.2.4.1.71.5.5.1.1
A single entry in the table represents a single frUniDlciLb component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciLbRowStatusEntry  

frUniDlciLbRowStatus 1.1.562.2.4.1.71.5.5.1.1.1
This variable is used as the basis for SNMP naming of frUniDlciLb components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

frUniDlciLbComponentName 1.1.562.2.4.1.71.5.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniDlciLbStorageType 1.1.562.2.4.1.71.5.5.1.1.4
This variable represents the storage type value for the frUniDlciLb tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniDlciLbIndex 1.1.562.2.4.1.71.5.5.1.1.10
This variable represents the index for the frUniDlciLb tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frUniDlciLbStatsTable 1.1.562.2.4.1.71.5.5.10
This group contains all the statistics for the data loopback tool.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniDlciLbStatsEntry

frUniDlciLbStatsEntry 1.1.562.2.4.1.71.5.5.10.1
An entry in the frUniDlciLbStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniDlciLbStatsEntry  

frUniDlciLbLocalTotalFrm 1.1.562.2.4.1.71.5.5.10.1.1
This attribute records the number of frames looped back to the link since loopback was last started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciLbLocalTotalBytes 1.1.562.2.4.1.71.5.5.10.1.2
This attribute records the number of bytes looped back to the link since loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciLbLocalFecnFrm 1.1.562.2.4.1.71.5.5.10.1.3
This attribute records the number of frames with the Forward Explicit Congestion Notification (FECN) bit set, looped back to the link since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciLbLocalBecnFrm 1.1.562.2.4.1.71.5.5.10.1.4
This attribute records the number of frames with the Backward Explicit Congestion Notification (BECN) bit set, looped back to the link since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciLbLocalDeFrm 1.1.562.2.4.1.71.5.5.10.1.5
This attribute records the number of frames with the Discard Eligibility (DE) bit set, looped back to the link since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciLbLocalDeBytes 1.1.562.2.4.1.71.5.5.10.1.6
This attribute records the number of bytes in frames with the Discard Eligibility (DE) bit set, looped back to the link since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciLbRemoteTotalFrm 1.1.562.2.4.1.71.5.5.10.1.7
This attribute records the number of frames looped back to the subnet since loopback was last started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciLbRemoteTotalBytes 1.1.562.2.4.1.71.5.5.10.1.8
This attribute records the number of bytes looped back to the subnet since loopback was last started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciLbRemoteFecnFrm 1.1.562.2.4.1.71.5.5.10.1.9
This attribute records the number of frames with the Forward Explicit Congestion Notification (FECN) bit set, looped back to the subnet since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciLbRemoteBecnFrm 1.1.562.2.4.1.71.5.5.10.1.10
This attribute records the number of frames with the Backward Explicit Congestion Notification (BECN) bit set, looped back to the subnet since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciLbRemoteDeFrm 1.1.562.2.4.1.71.5.5.10.1.13
This attribute records the number of frames with the Discard Eligibility (DE) bit set, looped back to the subnet since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniDlciLbRemoteDeBytes 1.1.562.2.4.1.71.5.5.10.1.14
This attribute records the number of bytes in frames with the Discard Eligibility (DE) bit set, looped back to the subnet since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniSig 1.1.562.2.4.1.71.6
OBJECT IDENTIFIER    

frUniSigRowStatusTable 1.1.562.2.4.1.71.6.1
This entry controls the addition and deletion of frUniSig components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniSigRowStatusEntry

frUniSigRowStatusEntry 1.1.562.2.4.1.71.6.1.1
A single entry in the table represents a single frUniSig component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniSigRowStatusEntry  

frUniSigRowStatus 1.1.562.2.4.1.71.6.1.1.1
This variable is used as the basis for SNMP naming of frUniSig components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frUniSigComponentName 1.1.562.2.4.1.71.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniSigStorageType 1.1.562.2.4.1.71.6.1.1.4
This variable represents the storage type value for the frUniSig tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniSigIndex 1.1.562.2.4.1.71.6.1.1.10
This variable represents the index for the frUniSig tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frUniSigRangeTable 1.1.562.2.4.1.71.6.11
This group contains the provisionable attribute to define the range of DLCIs for PVCs and SVCs. The purpose of this range is to prevent DLCI collisions between the provisioned PVCs and the dynamic SVCs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniSigRangeEntry

frUniSigRangeEntry 1.1.562.2.4.1.71.6.11.1
An entry in the frUniSigRangeTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniSigRangeEntry  

frUniSigHighestPvcDlci 1.1.562.2.4.1.71.6.11.1.1
This attribute specifies the highest DLCI value that can be provisioned for a PVC. If the operator defines a PVC DLCI number higher than this value, the provisioning will be rejected. The value 0 is used to indicate that no PVCs are allowed on the interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 16..1007  

frUniSigServParmsTable 1.1.562.2.4.1.71.6.12
This group contains the provisionable Q.933 service parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniSigServParmsEntry

frUniSigServParmsEntry 1.1.562.2.4.1.71.6.12.1
An entry in the frUniSigServParmsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniSigServParmsEntry  

frUniSigMaximumAggregateSvcCir 1.1.562.2.4.1.71.6.12.1.1
This attribute specifies the maximum aggregate user to network direction CIR allowed for SVCs on the interface. It is provisioned as a percentage of the access link speed. This attribute is used to limit the amount of guaranteed SVC throughput allowed into the network at this interface. This attribute is obsoleted, during the migration, the value of this attribute will be transfered to maximumAggregateSvcCirNormalQ or maximumAggregateSvcCirHighQ depending on the value of the attribute outDefaultPathSensitivity under DNA component.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Unsigned32 0..10000  

frUniSigMaximumAggregateSvcEir 1.1.562.2.4.1.71.6.12.1.2
This attribute specifies the maximum aggregate user to network direction EIR allowed for SVCs on the interface. It is provisioned as a percentage of the access link speed. This attribute is ignored if unlimitedAggregateEir, another attribute under the same group, is set to yes. This attribute is used to limit the amount of excess SVC throughput allowed into the network at this interface. This attribute is obsoleted, during the migration, the value of this attribute will be transfered to maximumAggregateSvcEirNormalQ or maximumAggregateSvcEirHighQ depending on the value of the attribute outDefaultPathSensitivity under DNA component.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniSigMaximumFrameSize 1.1.562.2.4.1.71.6.12.1.3
This attribute specifies the maximum number of octets that may be included in the information field of the user DLCI assigned for this call. Its value must not be smaller than the value of defaultMaximumFrameSize.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..8187  

frUniSigDefaultMaximumFrameSize 1.1.562.2.4.1.71.6.12.1.4
This attribute specifies the default maximum number of octets that may be included in the information field of the user DLCI assigned for this call. This value is used during call parameter negotiation for SVC calls on this interface when the maximum frame size is not specified in the user's SETUP message. The value of this attribute must not exceed the value of the maximumFrameSize attribute.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..8187  

frUniSigDefaultCommittedInformationRate 1.1.562.2.4.1.71.6.12.1.5
This attribute specifies the default user to network direction CIR. This value is used during call parameter negotiation for SVC calls on this interface when the CIR is not specified in the user's SETUP message.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..52000000  

frUniSigDefaultCommittedBurstSize 1.1.562.2.4.1.71.6.12.1.6
This attribute specifies the default user to network direction Bc. This value is used during call parameter negotiation for SVC calls on this interface when the Bc is not specified in the user's SETUP message.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..52000000  

frUniSigDefaultExcessBurstSize 1.1.562.2.4.1.71.6.12.1.7
This attribute specifies the default user to network direction Be. This value is used during call parameter negotiation for SVC calls on this interface when the Be is not specified in the user's SETUP message.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..52000000  

frUniSigUnlimitedAggregateEir 1.1.562.2.4.1.71.6.12.1.8
This attribute specifies whether the network will enforce aggregate EIR during SVC call establishment. The network keeps track of the sum of user to network EIRs for all the SVC DLCIs at this interface. If this attribute is set to no, then the requested EIR for each new SVC call will be adjusted if the resulting aggregate EIR exceeds the value contained in one of the following attributes (depending on the requested Transfer Priority): maximumAggregateSvcEirNormalQ, maximumAggregateSvcEirHighQ or maximumAggregateSvcEirInterruptQ. This may lead to a rejection of the call setup. If this value is set to yes, then no checks will take place.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

frUniSigRateEnforcement 1.1.562.2.4.1.71.6.12.1.9
This attribute specifies whether rate enforcement is in effect for SVCs on this interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

frUniSigRateAdaptation 1.1.562.2.4.1.71.6.12.1.10
This attribute specifies whether closed-loop rate adaptation is in effect for SVCs on this interface. Rate adaptation is a feature that, in periods of congestion, adapts the rate at which the user is allowed to send data into the network to that which the network is able to handle at that time. This pro-active measure of handling congestion optimizes network resources by causing the ingress to discard frames that would otherwise be discarded in the network. If this attribute is set to on, then, at the onset of congestion, the excess information rate (EIR) is reduced to a very low rate. If congestion persists, then the allowed CIR is reduced geometrically by 25% of the current value at that time. The minimum to which CIR can be reduced is 1/16th (6.25%) of the provisioned value. As congestion alleviates, CIR is increased linearly by 6.25% of the provisioned value specified in committedInformationRate. If set to eirOnly, then rate adaptation will only apply to the excess information rate (EIR). At the onset of congestion, the allowed EIR is reduced by 25% of its provisioned value. If congestion persists, EIR is reduced geometrically by 25% of the current value at that time. As congestion alleviates, EIR is gradually increased linearly by 6.25% of the provisioned EIR. If set to cirProportionate, then rate adaptation will also only apply to the excess information rate (EIR). At the onset of congestion the initial allowed EIR is set to a multiple of the provisioned CIR. If congestion persists, the allowed EIR is reduced geometrically by 25% of the current value at that time. As congestion alleviates, EIR is gradually increased linearly by 6.25% of the provisioned EIR. Note that the allowed EIR may be set higher than the provisioned EIR, since it is calculated initially using another parameter, the provisioned CIR. If the allowed EIR at the moment is higher than the provisioned EIR, then the provisioned EIR is used instead. This attribute can only be turned on or eirOnly if rateEnforcement is turned on.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1), eirOnly(2), cirProportionate(3)  

frUniSigMaximumAggregateSvcCirNormalQ 1.1.562.2.4.1.71.6.12.1.11
This attribute specifies the maximum aggregate user to network direction CIR allowed for SVCs on the interface. It is provisioned as a percentage of the access link speed. This attribute is used to limit, at this interface, the amount of guaranteed SVC throughput allowed into the network through the normal priority queue.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..10000  

frUniSigMaximumAggregateSvcCirHighQ 1.1.562.2.4.1.71.6.12.1.12
This attribute specifies the maximum aggregate user to network direction CIR allowed for SVCs on the interface. It is provisioned as a percentage of the link access speed. This attribute is used to limit, at this interface, the amount of guaranteed SVC throughput allowed into the network through the high priority queue.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..10000  

frUniSigMaximumAggregateSvcCirInterruptQ 1.1.562.2.4.1.71.6.12.1.13
This attribute specifies the maximum aggregate user to network direction CIR allowed for SVCs on the interface. It is provisioned as a percentage of the link access speed. This attribute is used to limit, at this interface, the amount of guaranteed SVC throughput allowed into the network through the interrupting queue.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..10000  

frUniSigMaximumAggregateSvcEirNormalQ 1.1.562.2.4.1.71.6.12.1.14
This attribute specifies the maximum aggregate user to network direction EIR allowed for SVCs on the interface. It is provisioned as a percentage of the access link speed. This attribute is ignored if unlimitedAggregateEir, another attribute under the same group, is set to yes. This attribute is used to limit, at this interface, the amount of excess SVC throughput allowed into the network through the normal priority queue.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniSigMaximumAggregateSvcEirHighQ 1.1.562.2.4.1.71.6.12.1.15
This attribute specifies the maximum aggregate user to network direction EIR allowed for SVCs on the interface. It is provisioned as a percentage of the access link speed. This attribute is ignored if unlimitedAggregateEir, another attribute under the same group, is set to yes. This attribute is used to limit, at this interface, the amount of excess SVC throughput allowed into the network through the high priority queue.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniSigMaximumAggregateSvcEirInterruptQ 1.1.562.2.4.1.71.6.12.1.16
This attribute specifies the maximum aggregate user to network direction EIR allowed for SVCs on the interface. It is provisioned as a percentage of the access link speed. This attribute is ignored if unlimitedAggregateEir, another attribute under the same group, is set to yes. This attribute is used to limit, at this interface, the amount of excess SVC throughput allowed into the network through the interrupting queue.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniSigX213IeHandling 1.1.562.2.4.1.71.6.12.1.17
The x213IeHandling attribute specifies how Frame Relay handles the X.213 Priority IE when it is in the Q.933 setup message. When the attribute is set to notSupported, the X.213 Priority IE will not be recognized in the setup message. A Q.933 status message will be sent to the calling DTE, with the indication that an unrecognized IE was encountered. The call setup then proceeds as normal, and the X.213 Priority IE does not appear in the setup message at the called end. When the attribute is set to proprietary, and the X.213 Priority IE is present in the Q.933 setup message, it will be recognized. If there is no Frame Transfer Priority IE in the setup message, the first data byte of the X.213 Priority IE is used to select the transfer and discard priority values for the connection and the X.213 Priority IE is signaled to the called end in the setup message. If the Frame Transfer Priority IE is present in the Q.933 setup message, its value is used to select the transfer priority, the discard priority is taken from the FRUNI Dna component, and the X.213 Priority IE is ignored. Refer to the related Application Note for further details before setting the attribute value to proprietary.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(0), proprietary(1)  

frUniSigRaSensitivity 1.1.562.2.4.1.71.6.12.1.18
This attribute specifies the sensitivity of the rate adaptation system for Svc's on this interface. Since this attribute is in the Sig Component of an FR Uni component, all SVC DLCI's created for this FR Uni Service will take the raSensitivity attribute provisioned here. A higher number indicates a higher sensitivity and therefore a quicker reaction time to network conditions. A quicker reaction time allows the network to discard frames at the access and protect network resources, but can lead to false alarms and a greater fluctuation of the allowed rate. A higher setting therefore tends to favour the protection of the network over the allowed throughput of the user. A lower number indicates a lower sensitivity and therefore a slower reaction to network conditions. A slower reaction time results in a greater amount of user traffic allowed into the network, but can lead to a waste of network bandwidth since the traffic may be discarded at the congested resource. A lower setting therefore tends to favour the allowed throughput of the user over the protection of the network. This attribute is applicable for adapting EIR when rateAdaptation is eirOnly or cirProportionate, or CIR when rateAdaptation is on. This attribute is ignored if rateAdaptation is turned off.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..20  

frUniSigUpdateBCI 1.1.562.2.4.1.71.6.12.1.19
This attribute specifies whether internal Backward Congestion Indication (BCI) bits will report congestion external to the Passport network, as communicated through incoming BECN bits. If updateBCI is set to on, then BCI bits for incoming frames will be set if the BECN on the frame is set. If updatBCI is set to off, then incoming BECN bits will have no effect. Setting updateBCI on for a DLCI means that the remote end of the DLCI, which is specified by the remotedna and remotedlci attributes of the dc component of the dlci, may perform Rate Adaptation using the flow of incoming BECN bits, in addition to internal Passport congestion management systems. If the rateAdaptation attribute of the remote dlci is provisioned as eirOnly, cirProportionate, or on, then congestion from another network connected to a Passport network may trigger dynamic congestion management. If the rateAdaptation attribute of the remote dlci is provisioned to off, then the setting of updateBCI attribute here will have no effect..
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

frUniSigDefaultLocCheck 1.1.562.2.4.1.71.6.12.1.20
This attribute specifies whether Passport needs to check the location of Cause IE in a Release or a Disc message issued by local DTE. If this bit is set to on, then Passport will check the location of Cause IE issued by the local DTE and overwrite it by 'user'. If it is set to off, then Passport will not check the location in Cause IE.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

frUniSigSysParmsTable 1.1.562.2.4.1.71.6.13
This group contains the provisionable Q.933 system parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniSigSysParmsEntry

frUniSigSysParmsEntry 1.1.562.2.4.1.71.6.13.1
An entry in the frUniSigSysParmsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniSigSysParmsEntry  

frUniSigCallSetupTimer 1.1.562.2.4.1.71.6.13.1.1
This attribute specifies the time the network will wait for a response to the SETUP message sent to the called user. Upon timer expiry, the SETUP message is retransmitted. The second expiry of this timer causes the call to be cleared. This value is specified in seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

frUniSigDisconnectTimer 1.1.562.2.4.1.71.6.13.1.2
This attribute specifies the time the network will wait for a response to the DISCONNECT message sent to the user. Upon timer expiry, the RELEASE message is sent. This value is specified in seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

frUniSigReleaseTimer 1.1.562.2.4.1.71.6.13.1.3
This attribute specifies the time the network will wait for a response to the RELEASE message sent to the user. Upon timer expiry, the RELEASE message is retransmitted. The second expiry of the timer causes the call to be released. This value is specified in seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

frUniSigCallProceedingTimer 1.1.562.2.4.1.71.6.13.1.4
This attribute specifies the time the network will wait for the CONNECT message from the called user after the network has received the optional CALL PROCEEDING message from the called user. Upon timer expiry, the call is cleared. This value is specified in seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

frUniSigNetworkType 1.1.562.2.4.1.71.6.13.1.5
This attribute specifies whether this Frame Relay service is running on a public or a private network. This value is used solely in populating applicable information elements within those Q.933 messages that require a public or private network indication.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER private(1), public(2)  

frUniSigLapfSysTable 1.1.562.2.4.1.71.6.14
This group contains the provisionable attributes for the SVC data link layer. The data link layer is governed primarily through ITU specification Q.922, and operates over DLCI 0..
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniSigLapfSysEntry

frUniSigLapfSysEntry 1.1.562.2.4.1.71.6.14.1
An entry in the frUniSigLapfSysTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniSigLapfSysEntry  

frUniSigWindowSize 1.1.562.2.4.1.71.6.14.1.2
This attribute specifies the window size. This is the maximum number of unacknowledged sequenced frames that may be outstanding from or to this interface at any one time.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..127  

frUniSigRetransmitLimit 1.1.562.2.4.1.71.6.14.1.3
This attribute specifies the number of times a frame can be retransmitted by the SVC data link layer before appropriate recovery action is taken.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..20  

frUniSigAckTimer 1.1.562.2.4.1.71.6.14.1.4
This attribute specifies the period in milliseconds that the network will wait for an acknowledgment to a sent frame. The value set for ackTimer must be less than the value set for idleProbeTimer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..10000  

frUniSigAckDelayTimer 1.1.562.2.4.1.71.6.14.1.5
This attribute specifies the maximum period in milliseconds that the network will wait before sending an acknowledgment for a received in-sequence I-frame. A value of 0 means there will be no delay in acknowledgment.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..10000  

frUniSigIdleProbeTimer 1.1.562.2.4.1.71.6.14.1.6
This attribute specifies the time period in milliseconds the link will be permitted to remain idle (that is, no frames are exchanged on the data link). Upon expiry of this timer, the network's side link layer polls its peer for status. The value set for idleProbeTimer must be greater than the value set for ackTimer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..65535000  

frUniSigStateTable 1.1.562.2.4.1.71.6.15
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniSigStateEntry

frUniSigStateEntry 1.1.562.2.4.1.71.6.15.1
An entry in the frUniSigStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniSigStateEntry  

frUniSigAdminState 1.1.562.2.4.1.71.6.15.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

frUniSigOperationalState 1.1.562.2.4.1.71.6.15.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

frUniSigUsageState 1.1.562.2.4.1.71.6.15.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

frUniSigStatsTable 1.1.562.2.4.1.71.6.16
This group contains the statistics related to the SVC signaling layer at the interface level.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniSigStatsEntry

frUniSigStatsEntry 1.1.562.2.4.1.71.6.16.1
An entry in the frUniSigStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniSigStatsEntry  

frUniSigCurrentNumberOfSvcCalls 1.1.562.2.4.1.71.6.16.1.1
This attribute shows the number of Frame Relay SVCs currently existing on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..992  

frUniSigInCalls 1.1.562.2.4.1.71.6.16.1.4
This attribute shows the current number of incoming SVCs on this interface (i.e. the number of SVCs for which this interface represents the destination end of the call).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigInCallsRefused 1.1.562.2.4.1.71.6.16.1.5
This attribute counts the number of incoming SVC call requests that are rejected by either this interface or by the called user. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigOutCalls 1.1.562.2.4.1.71.6.16.1.6
This attribute shows the current number of outgoing SVCs on this interface (i.e. the number of SVCs for which this interface represents the source end of the call).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigOutCallsFailed 1.1.562.2.4.1.71.6.16.1.7
This attribute counts the number of outgoing SVC call requests that are rejected by either this interface, or by the network side of the destination end, or by the called user. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigProtocolErrors 1.1.562.2.4.1.71.6.16.1.8
This attribute counts the number of times a Q.933 protocol error has occurred. Any one of the following events constitutes a protocol error: 1. In the user-signaled Link Layer Core Parameters IE within the SETUP or CONNECT messages, Cir, Bc and Be are all zero; 2. In the user-signaled Link Layer Core Parameters IE within the SETUP or CONNECT messages, Cir is zero but Bc is non-zero, or Bc is zero but Cir is non-zero; 3. In the user-signaled Link Layer Core Parameters IE within the SETUP or CONNECT messages, the minimum acceptable Cir is greater than Cir; 4. At the destination end, any of the destination to source direction link layer core parameters has been increased in the CONNECT message from the called user; 5. At the destination end, the destination to source direction Cir in the CONNECT message is smaller than the corresponding minimum acceptable Cir signaled to the called user; 6. At the source end, any of the source to destination direction link layer core parameters in the CONNECT message from the destination end has been increased; 7. At the source end, the source to destination direction Cir, after negotiation, is smaller than the corresponding minimum acceptable Cir; 8. The network has received a STATUS message from the user with an incompatible Q.933 state. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigQualityOfServiceNotAvailable 1.1.562.2.4.1.71.6.16.1.9
This attribute counts the number of incoming and outgoing SVCs that are rejected because the quality of service requested cannot be met by the network. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigSetupTimeout 1.1.562.2.4.1.71.6.16.1.10
This attribute counts the number of times the T303 setup timer has expired. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigLastCauseInStatusMsgReceived 1.1.562.2.4.1.71.6.16.1.11
This attribute shows the cause value in the last received user's STATUS message to an existing call. The DLCI to which this STATUS message applies is specified in the lastDlciReceivedStatus attribute. The initial value of this attribute is 0 which means that no STATUS message has been received for an existing call yet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

frUniSigLastStateInStatusMsgReceived 1.1.562.2.4.1.71.6.16.1.12
This attribute shows the state value in the last received user's STATUS message to an existing call. The DLCI to which this STATUS message applies is specified in the lastDlciReceivedStatus attribute. The initial value of this attribute is notApplicable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER null(0), callInitiated(1), n2(2), outgoingCallProceeding(3), n4(4), n5(5), callPresent(6), n7(7), n8(8), incomingCallProceeding(9), active(10), disconnectRequest(11), disconnectIndication(12), n13(13), n14(14), n15(15), n16(16), n17(17), n18(18), releaseRequest(19), notApplicable(20), n21(21), n22(22), n23(23), n24(24), n25(25), n26(26), n27(27), n28(28), n29(29), n30(30), n31(31), n32(32), n33(33), n34(34), n35(35), n36(36), n37(37), n38(38), n39(39), n40(40), n41(41), n42(42), n43(43), n44(44), n45(45), n46(46), n47(47), n48(48), n49(49), n50(50), n51(51), n52(52), n53(53), n54(54), n55(55), n56(56), n57(57), n58(58), n59(59), n60(60), n61(61), n62(62), n63(63)  

frUniSigLastDlciReceivedStatus 1.1.562.2.4.1.71.6.16.1.13
This attribute shows the value of the DLCI that has most recently received a STATUS message from the user. The initial value of this attribute is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0 | 16..1007  

frUniSigLastQ933StateReceivedStatus 1.1.562.2.4.1.71.6.16.1.14
This attribute shows the network Q.933 state of the DLCI that has most recently received a STATUS message from the user. The DLCI to which this STATUS message applies is specified in the lastDlciReceivedStatus attribute. The initial value of this attribute is notApplicable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER null(0), callInitiated(1), outgoingCallProceeding(3), callPresent(6), incomingCallProceeding(9), active(10), disconnectRequest(11), disconnectIndication(12), releaseRequest(19), notApplicable(20)  

frUniSigLastTimeMsgBlockCongested 1.1.562.2.4.1.71.6.16.1.15
This attribute displays the most recent time that an SVC DLCI has failed to get a message block due to message block congestion. Exceptional behavior can occur due to this. The DLCI that has most recently encountered this is indicated by the lastDlciWithMsgBlockCongestion attribute. However, all SVC DLCIs may be affected. The initial value of this attribute is 0000-00-00 00:00.
Status: mandatory Access: read-only
OBJECT-TYPE    
  EnterpriseDateAndTime Size(0|16)  

frUniSigLastDlciWithMsgBlockCongestion 1.1.562.2.4.1.71.6.16.1.16
This attribute shows the value of the DLCI that has most recently failed to get a message block due to message block congestion. The initial value of this attribute is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0 | 16..1007  

frUniSigCurrentAggregateSvcCirNormalQ 1.1.562.2.4.1.71.6.16.1.17
This attribute shows the aggregate SVC CIR (for traffic transiting in the network through normal priority queue) assigned to existing SVCs on the interface. The value of currentAggregateSvcCirNormalQ could be greater than the provisionable value of maximumAggregateSvcCiNormalQ if the value of maximumAggregateSvcCirNormalQ has been changed during the service of this FrUni.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniSigCurrentAggregateSvcCirHighQ 1.1.562.2.4.1.71.6.16.1.18
This attribute shows the aggregate SVC CIR (for traffic transiting in the network through high priority queue) assigned to existing SVCs on the interface. The value of currentAggregateSvcCirHighQ could be greater than the provisionable value of maximumAggregateSvcCirHighQ if the value of maximumAggregateSvcCirHighQ has been changed during the service of this FrUni.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniSigCurrentAggregateSvcCirInterruptQ 1.1.562.2.4.1.71.6.16.1.19
This attribute shows the aggregate SVC CIR (for traffic transiting in the network through interrupting queue) assigned to existing SVCs on the interface. The value of currentAggregateSvcCirInterruptQ could be greater than the provisionable value of maximumAggregateSvcCirInterruptQ if the value of maximumAggregateSvcCirInterruptQ has been changed during the service of this FrUni.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniSigCurrentAggregateSvcEirNormalQ 1.1.562.2.4.1.71.6.16.1.20
This attribute shows the aggregate SVC EIR (for excess traffic transiting in the network through normal priority queue) assigned to existing SVCs on the interface. The value of currentAggregateSvcEirNormalQ could be greater than the provisionable value of maximumAggregateSvcEirNormalQ if the value of maximumAggregateSvcEiNormalQ has been changed during the service of this FrUni or unlimitedAggregateEir is set to yes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniSigCurrentAggregateSvcEirHighQ 1.1.562.2.4.1.71.6.16.1.21
This attribute shows the aggregate SVC EIR (for excess traffic transiting in the network through high priority queue) assigned to existing SVCs on the interface. The value of currentAggregateSvcEirHighQ could be greater than the provisionable value of maximumAggregateSvcEirHighQ if the value of maximumAggregateSvcEirHighQ has been changed during the service of this FrUni or unlimitedAggregateEir is set to yes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniSigCurrentAggregateSvcEirInterruptQ 1.1.562.2.4.1.71.6.16.1.22
This attribute shows the aggregate SVC EIR (for excess traffic transiting in the network through interrupting queue) assigned to existing SVCs on the interface. The value of currentAggregateSvcEirInterruptQ could be greater than the provisionable value of maximumAggregateSvcEirInterruptQ if the value of maximumAggregateSvcEirInterruptQ has been changed during the service of this FrUni or unlimitedAggregateEir is set to yes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniSigLapfStatusTable 1.1.562.2.4.1.71.6.17
This group contains the Q.922 SVC data link layer status.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniSigLapfStatusEntry

frUniSigLapfStatusEntry 1.1.562.2.4.1.71.6.17.1
An entry in the frUniSigLapfStatusTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniSigLapfStatusEntry  

frUniSigCurrentState 1.1.562.2.4.1.71.6.17.1.1
This attribute shows the current state of the SVC data link layer interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disconnected(1), linkSetup(2), disconnectRequest(4), informationTransfer(5), waitingAck(7)  

frUniSigLastStateChangeReason 1.1.562.2.4.1.71.6.17.1.2
This attribute shows the reason for the most recent state change. notStarted - this is the default state after SVC data link has just been created. abmeEntered - SVC data link has entered Asynchronous Balanced Mode after SABME or UA has been received. abmeReset - the data link has been reset. dmReceived - DM response received. dmSent - DM sent. discReceived - DISC response received. discSent - DISC sent. frmrReceived - FRMR received. n200RetranTimeOut - retransmitLimit has been exceeded. other - unspecified state change reasons. The most likely reason for this is the transition from state waitingAck to state informationTransfer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notStarted(1), abmeEntered(3), abmeReset(5), dmReceived(6), dmSent(7), discReceived(8), discSent(9), frmrReceived(10), n200RetranTimeOut(12), other(13)  

frUniSigFrmrReceive 1.1.562.2.4.1.71.6.17.1.3
This attribute shows the information field of the FRMR most recently received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(0..8)  

frUniSigCurrentQueueSize 1.1.562.2.4.1.71.6.17.1.4
This attribute shows the current number of frames in the SVC data link layer transmit queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigLapfStatsTable 1.1.562.2.4.1.71.6.18
This group contains the statistics for the SVC data link layer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniSigLapfStatsEntry

frUniSigLapfStatsEntry 1.1.562.2.4.1.71.6.18.1
An entry in the frUniSigLapfStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniSigLapfStatsEntry  

frUniSigStateChange 1.1.562.2.4.1.71.6.18.1.1
This attribute counts the number of times the SVC data link layer interface has changed state. Frequent state changes may indicate a problem with the line quality. While the data link layer is in informationTransfer state, this counter will increment on each expiry of idleProbeTimer as its state goes from informationTransfer to waitingAck and back. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigRemoteBusy 1.1.562.2.4.1.71.6.18.1.2
This attribute counts the number of times transmission of an I-frame was unsuccessful due to a perceived remote busy condition (window closed or remote busy). When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigReceiveRejectFrame 1.1.562.2.4.1.71.6.18.1.3
This attribute counts the number of REJ frames received by the interface. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigAckTimeout 1.1.562.2.4.1.71.6.18.1.4
This attribute counts the number of times the ackTimer has expired. Frequent increments of this counter indicate a problem at the link or improper values have been chosen for ackTimer and ackDelayTimer between the local and remote sides. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigIFramesTransmitted 1.1.562.2.4.1.71.6.18.1.5
This attribute counts the number of SVC I-frames transmitted to the interface on DLCI 0. An I-frame may be counted more than once if there are retransmissions at the SVC data link layer. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigIFramesTxDiscarded 1.1.562.2.4.1.71.6.18.1.6
This attribute counts the number of SVC I-frames that are bound for the link but have been discarded. Discard reasons may be one of the following: 1. the frame length is beyond allow limit. 2. the SVC data link layer is in disconnected state. 3. the transmit queue has been purged because the queue length has reached the reset threshold. 4. the transmit queue or the queue waiting for acknowledgment has been purged because the link cannot be re-established. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigIFramesReceived 1.1.562.2.4.1.71.6.18.1.7
This attribute counts the number of SVC I-frames received from the interface. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigIFramesRcvdDiscarded 1.1.562.2.4.1.71.6.18.1.8
This attribute counts the number of SVC I-frames received but have been discarded. The discard reasons are: 1. incorrect frame size 2. frame is out of sequence 3. frame received while the network side of the SVC data link layer is not in the informationTransfer or waitingAck state. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniSigSvcaccTable 1.1.562.2.4.1.71.6.19
This group contains the provisionable attribute to define the defaultAccounting attribute..
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniSigSvcaccEntry

frUniSigSvcaccEntry 1.1.562.2.4.1.71.6.19.1
An entry in the frUniSigSvcaccTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniSigSvcaccEntry  

frUniSigDefaultAccounting 1.1.562.2.4.1.71.6.19.1.1
This attribute specifies whether accounting data collection and record generation is turned on at this DLCI. For accounting data collection and record generation to be turned on, the defaultAccounting bit and at least one of the accountCollection bits in the DataNetworkAddress component must be set to on.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

frUniSigCodesTable 1.1.562.2.4.1.71.6.20
This group contains the remote data network address, the last SVC clear cause and the last SVC diagnostic code coming from the subnet or the local VC.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniSigCodesEntry

frUniSigCodesEntry 1.1.562.2.4.1.71.6.20.1
An entry in the frUniSigCodesTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniSigCodesEntry  

frUniSigLastClearRemoteDataNetworkAddress 1.1.562.2.4.1.71.6.20.1.1
This attribute indicates the Data Network Address (DNA) of the remote (the other end of the SVC connection) of the call which cleared last and whose clear and diagnostic codes were recorded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DigitString Size(0..15)  

frUniSigLastClearCause 1.1.562.2.4.1.71.6.20.1.2
This attribute indicates the last SVC clear cause signalled at the end of the connection or failure to connect. It is updated only if the clear request comes from the subnet or the call is rejected locally by the VC. The same set of possible values provides the clear cause field in the accounting record.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

frUniSigLastDiagnosticCode 1.1.562.2.4.1.71.6.20.1.3
This attribute indicates the last SVC diagnostic code signalled at the end of the connection or failure to connect. It is updated if the clear request comes from the subnet or the call is rejected locally by the VC. The same set of possible values provides the diagnostic code field in the accounting record.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

frUniVFramer 1.1.562.2.4.1.71.8
OBJECT IDENTIFIER    

frUniVFramerRowStatusTable 1.1.562.2.4.1.71.8.1
This entry controls the addition and deletion of frUniVFramer components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniVFramerRowStatusEntry

frUniVFramerRowStatusEntry 1.1.562.2.4.1.71.8.1.1
A single entry in the table represents a single frUniVFramer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniVFramerRowStatusEntry  

frUniVFramerRowStatus 1.1.562.2.4.1.71.8.1.1.1
This variable is used as the basis for SNMP naming of frUniVFramer components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frUniVFramerComponentName 1.1.562.2.4.1.71.8.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniVFramerStorageType 1.1.562.2.4.1.71.8.1.1.4
This variable represents the storage type value for the frUniVFramer tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniVFramerIndex 1.1.562.2.4.1.71.8.1.1.10
This variable represents the index for the frUniVFramer tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frUniVFramerProvTable 1.1.562.2.4.1.71.8.10
This group contains provisionable attributes for the VirtualFramer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniVFramerProvEntry

frUniVFramerProvEntry 1.1.562.2.4.1.71.8.10.1
An entry in the frUniVFramerProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniVFramerProvEntry  

frUniVFramerOtherVirtualFramer 1.1.562.2.4.1.71.8.10.1.1
This attribute specifies the other VirtualFramer to which the service is linked, for example, FrUni/n VirtualFramer, FrDte/n VirtualFramer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

frUniVFramerLogicalProcessor 1.1.562.2.4.1.71.8.10.1.2
This attribute specifies the logical processor on which the service component will reside.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

frUniVFramerStateTable 1.1.562.2.4.1.71.8.11
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniVFramerStateEntry

frUniVFramerStateEntry 1.1.562.2.4.1.71.8.11.1
An entry in the frUniVFramerStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniVFramerStateEntry  

frUniVFramerAdminState 1.1.562.2.4.1.71.8.11.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

frUniVFramerOperationalState 1.1.562.2.4.1.71.8.11.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

frUniVFramerUsageState 1.1.562.2.4.1.71.8.11.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

frUniVFramerStatsTable 1.1.562.2.4.1.71.8.12
This group contains the operational statistics data for a VirtualFramer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniVFramerStatsEntry

frUniVFramerStatsEntry 1.1.562.2.4.1.71.8.12.1
An entry in the frUniVFramerStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniVFramerStatsEntry  

frUniVFramerFrmToOtherVFramer 1.1.562.2.4.1.71.8.12.1.2
This attribute counts the frames transmitted to the otherVirtualFramer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

frUniVFramerFrmFromOtherVFramer 1.1.562.2.4.1.71.8.12.1.3
This attribute counts the frames received from the otherVirtualFramer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

frUniVFramerOctetFromOtherVFramer 1.1.562.2.4.1.71.8.12.1.5
This attribute counts the octets received from the otherVirtualFramer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

frUniLts 1.1.562.2.4.1.71.9
OBJECT IDENTIFIER    

frUniLtsRowStatusTable 1.1.562.2.4.1.71.9.1
This entry controls the addition and deletion of frUniLts components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLtsRowStatusEntry

frUniLtsRowStatusEntry 1.1.562.2.4.1.71.9.1.1
A single entry in the table represents a single frUniLts component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLtsRowStatusEntry  

frUniLtsRowStatus 1.1.562.2.4.1.71.9.1.1.1
This variable is used as the basis for SNMP naming of frUniLts components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frUniLtsComponentName 1.1.562.2.4.1.71.9.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniLtsStorageType 1.1.562.2.4.1.71.9.1.1.4
This variable represents the storage type value for the frUniLts tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniLtsIndex 1.1.562.2.4.1.71.9.1.1.10
This variable represents the index for the frUniLts tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

frUniLtsSetupTable 1.1.562.2.4.1.71.9.10
This attribute group contains the parameters used to configure the behavior of the Frame Relay Load Test System.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLtsSetupEntry

frUniLtsSetupEntry 1.1.562.2.4.1.71.9.10.1
An entry in the frUniLtsSetupTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLtsSetupEntry  

frUniLtsDuration 1.1.562.2.4.1.71.9.10.1.200
This attribute specifies the duration of the test in milliseconds. The test will run until the duration expires or the STOP command is issued. A value of 0 is used to indicate infinity.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniLtsAlgorithm 1.1.562.2.4.1.71.9.10.1.201
This attribute specifies which algorithm is used to generate the frames. ContinuousBurst This mode of traffic generation creates traffic at the maximum rate possible until all of the frames have been sent. The generator then waits until the end of the timeInterval to begin again. IntervalBurst This algorithm attempts to generate 10 ms bursts of burstSize frames. It will generate as many of the burstSize frames as it can per sub-interval. DelayedBurst This algorithm generates bursts of burstSize frames separated by 10 ms delays. FixedBurst This aglorithm is similar to IntervalBurst, except a fixed burst size of 12 frames is used. delayMeasurement This algorithm is used to measure delay. The specified number of frames in the indicated pattern are generated, one at a time, with a maximum wait of maxDelay before sending the next frame. This algorithm is not implemented yet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER continousBurst(0), intervalBurst(1), delayBurst(2), fixedBurst(3)  

frUniLtsBurstSize 1.1.562.2.4.1.71.9.10.1.204
This attribute specifies the number of frames per burst under the delayedBurst and intervalBurst algorithms.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..250  

frUniLtsTimeInterval 1.1.562.2.4.1.71.9.10.1.205
This attribute specifies the time interval to the specified number of seconds. Granuality is in centiseconds. Maximum is 1 minute.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..60000  

frUniLtsStateTable 1.1.562.2.4.1.71.9.11
This group contains the operation statistics of the load generator.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLtsStateEntry

frUniLtsStateEntry 1.1.562.2.4.1.71.9.11.1
An entry in the frUniLtsStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLtsStateEntry  

frUniLtsGeneratorState 1.1.562.2.4.1.71.9.11.1.200
This attribute indicates whether the Lts is generating traffic.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER stopped(0), running(1)  

frUniLtsCycleIncomplete 1.1.562.2.4.1.71.9.11.1.201
This attribute indicates whether the time required to generate all of the enabled patterns is more than timeInterval by a true value. Otherwise, this flag is set to false. Default is True.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

frUniLtsLastActiveInterval 1.1.562.2.4.1.71.9.11.1.202
This attribute indicates the actual time it took to generate all of the enabled patterns in the last cycle. If cycleIncomplete is true, this value should be zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniLtsLoad 1.1.562.2.4.1.71.9.11.1.204
This attribute indicates the load being generated. This value represents that calculated using the set number of ticks. The actual burstTimeInterval may differ. One entire cycle of the patterns is completed in activeInterval and thus most of the load may be concentrated early in the set interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FixedPoint3 0..4294967295  

frUniLtsElapsedGenerationTime 1.1.562.2.4.1.71.9.11.1.205
This attribute indicates how many milliseconds have elapsed since the start of this test.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniLtsResultsTable 1.1.562.2.4.1.71.9.12
This group contains the frame counting attributes for the LTS component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLtsResultsEntry

frUniLtsResultsEntry 1.1.562.2.4.1.71.9.12.1
An entry in the frUniLtsResultsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLtsResultsEntry  

frUniLtsFramesTx 1.1.562.2.4.1.71.9.12.1.200
This attribute specifies the number of frames send to the network since the last time these statistics were cleared. This is similar to the framesToIf attribute of the FRAMER component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

frUniLtsBytesTx 1.1.562.2.4.1.71.9.12.1.204
This attribute indicates the number of bytes sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniLtsBitRateTx 1.1.562.2.4.1.71.9.12.1.208
This attribute indicates the bit rate being sent to the link. It should only differ from the load if the burstTimeInterval would be >= the timeInterval or burstSize frames cannot be generated in 10ms (intervalBurst algorithm).
Status: mandatory Access: read-only
OBJECT-TYPE    
  FixedPoint3 0..4294967295  

frUniLtsFrameRateTx 1.1.562.2.4.1.71.9.12.1.209
This attribute indicates the frame rate being sent to the link. It is calculated using the number of frames sent to the link in one cycle of the patterns.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniLtsPat 1.1.562.2.4.1.71.9.2
OBJECT IDENTIFIER    

frUniLtsPatRowStatusTable 1.1.562.2.4.1.71.9.2.1
This entry controls the addition and deletion of frUniLtsPat components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLtsPatRowStatusEntry

frUniLtsPatRowStatusEntry 1.1.562.2.4.1.71.9.2.1.1
A single entry in the table represents a single frUniLtsPat component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLtsPatRowStatusEntry  

frUniLtsPatRowStatus 1.1.562.2.4.1.71.9.2.1.1.1
This variable is used as the basis for SNMP naming of frUniLtsPat components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

frUniLtsPatComponentName 1.1.562.2.4.1.71.9.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frUniLtsPatStorageType 1.1.562.2.4.1.71.9.2.1.1.4
This variable represents the storage type value for the frUniLtsPat tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

frUniLtsPatIndex 1.1.562.2.4.1.71.9.2.1.1.10
This variable represents the index for the frUniLtsPat tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 0..29  

frUniLtsPatDefaultsTable 1.1.562.2.4.1.71.9.2.10
This attribute group contains the specifications of the pattern.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLtsPatDefaultsEntry

frUniLtsPatDefaultsEntry 1.1.562.2.4.1.71.9.2.10.1
An entry in the frUniLtsPatDefaultsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLtsPatDefaultsEntry  

frUniLtsPatDefaultDlci 1.1.562.2.4.1.71.9.2.10.1.200
This attribute specifies for which dlci (on the local end) the frames are destined.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 16..1007  

frUniLtsPatDefaultNumFrames 1.1.562.2.4.1.71.9.2.10.1.201
This attribute specifies the number of frames in this pattern. This is the number of frames of this type which will be generated in one timeInterval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniLtsPatDefaultDataSize 1.1.562.2.4.1.71.9.2.10.1.202
This attribute specifies the payload size of each frame in bytes. This is in excess to the header.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..8200  

frUniLtsPatDefaultHeaderBits 1.1.562.2.4.1.71.9.2.10.1.203
This attribute specifies whether the following bits are on/off in the header of each frame. The following bits can be set: BeCn, C/R, De, FeCn Description of bits: becn(0) fecn(1) cr(2) de(3)
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1)  

frUniLtsPatDefaultHeaderLength 1.1.562.2.4.1.71.9.2.10.1.204
This attribute specifies the size of the frame relay header in bytes. Passport currently only supports a 2-byte header.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 2..4  

frUniLtsPatDefaultEABits 1.1.562.2.4.1.71.9.2.10.1.205
This attribute specifies how the address field extension bits are set in the frame header. Consider the value to be a four bit binary number. For example, 4 = 0100. Only the first headerLength bits are used. For instance, suppose headerLength is 3, then the appropriate EABits is 2, or 0010. This attribute can be used to create a header of length greater than two bytes or to specify incorrect EABits in the header.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Hex 0..15  

frUniLtsPatDefaultPayloadPattern 1.1.562.2.4.1.71.9.2.10.1.206
This attribute specifies the payload of each frame. The value specified is in hexadecimal, where every two digits represent a byte. A maximum of 24 digits (12 bytes) may be set, after which the pattern will repeat in the payload (depending on repeatPattern attribute). NOTE: If a RFC 1490 header is specified, via the 1490Header attribute, the specified pattern will begin following the header (i.e. at the 9th byte in the payload).
Status: mandatory Access: read-write
OBJECT-TYPE    
  HexString Size(1..12)  

frUniLtsPatDefaultRfc1490Header 1.1.562.2.4.1.71.9.2.10.1.207
This attribute specifies the appropriate RFC 1490 encapsulated header of the frame. A value of 0 indicates no 1490 header. NOTE: This header resides in the first 8 bytes of the payload. If the specified value is non-zero, then the payload pattern provisioned will begin at the 9th byte.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15), n16(16), n17(17), none(18)  

frUniLtsPatDefaultUseBadLrc 1.1.562.2.4.1.71.9.2.10.1.208
This attribute specifies whether the frames from this pattern are to have a bad LRC prior to being sent to the framer. The LRC is checked while the frame is being put onto the link and the failure should cause an abort frame to be sent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

frUniLtsPatSetupTable 1.1.562.2.4.1.71.9.2.11
This attribute group contains the specifications of the pattern.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLtsPatSetupEntry

frUniLtsPatSetupEntry 1.1.562.2.4.1.71.9.2.11.1
An entry in the frUniLtsPatSetupTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLtsPatSetupEntry  

frUniLtsPatDlci 1.1.562.2.4.1.71.9.2.11.1.200
This attribute specifies for which dlci (on the local end) the frames are destined.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 16..1007  

frUniLtsPatNumFrames 1.1.562.2.4.1.71.9.2.11.1.201
This attribute specifies the number of frames in this pattern. This is the number of frames of this type which will be generated in one timeInterval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frUniLtsPatDataSize 1.1.562.2.4.1.71.9.2.11.1.202
This attribute specifies the payload size of each frame in bytes. This is in excess to the header.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..8200  

frUniLtsPatHeaderBits 1.1.562.2.4.1.71.9.2.11.1.203
This attribute specifies whether the following bits are on/off in the header of each frame. The following bits can be set: BeCn, C/R, De, FeCn Description of bits: becn(0) fecn(1) cr(2) de(3)
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1)  

frUniLtsPatHeaderLength 1.1.562.2.4.1.71.9.2.11.1.204
This attribute specifies the size of the frame relay header in bytes. Passport currently only supports a 2-byte header. Valid values are 0, 2, 3, 4. 0 indicates to use no header. That is, the frame will start with either the payload or rfc1490 header.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 2..4  

frUniLtsPatEaBits 1.1.562.2.4.1.71.9.2.11.1.205
This attribute specifies how the address field extension bits are set in the frame header. Consider the value to be a four bit binary number. For example, 4 = 0100. Only the first headerLength bits are used. For instance, suppose headerLength is 3, then the appropriate eaBits is 2, or 0010. This attribute can be used to create a header of length greater than two bytes or to specify incorrect eaBits in the header.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Hex 0..15  

frUniLtsPatPayloadPattern 1.1.562.2.4.1.71.9.2.11.1.206
This attribute specifies the payload of each frame. The value specified is in hexadecimal, where every two digits represent a byte. A maximum of 24 digits (12 bytes) may be set, after which the pattern will repeat in the payload (depending on repeatPattern attribute). NOTE: If a RFC 1490 header is specified, via the 1490Header attribute, the specified pattern will begin following the header (i.e. at the 9th byte in the payload).
Status: mandatory Access: read-write
OBJECT-TYPE    
  HexString Size(1..12)  

frUniLtsPatRfc1490Header 1.1.562.2.4.1.71.9.2.11.1.207
This attribute specifies the appropriate RFC 1490 encapsulated header of the frame. A value of 0 indicates no 1490 header. NOTE: This header resides in the first 8 bytes of the payload. If the specified value is non-zero, then the payload pattern provisioned will begin at the 9th byte.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15), n16(16), n17(17), none(18)  

frUniLtsPatUseBadLrc 1.1.562.2.4.1.71.9.2.11.1.208
This attribute specifies whether the frames from this pattern are to have a bad LRC prior to being sent to the framer. The LRC is checked while the frame is being put onto the link and the failure should cause an abort frame to be sent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

frUniLtsPatOpDataTable 1.1.562.2.4.1.71.9.2.12
This group contains the operational attributes which allow changing the pattern outside of provisioning mode.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLtsPatOpDataEntry

frUniLtsPatOpDataEntry 1.1.562.2.4.1.71.9.2.12.1
An entry in the frUniLtsPatOpDataTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLtsPatOpDataEntry  

frUniLtsPatFramePattern 1.1.562.2.4.1.71.9.2.12.1.200
This attribute displays the first 20 to 24 bytes of the frame payload, depending on the frame relay header size selected. This attribute represents the frame if it were at least 20 to 24 bytes in size. That is, the actual frame may be smaller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(20..24)  

frUniLtsPatHdlcBitsInserted 1.1.562.2.4.1.71.9.2.12.1.201
This attribute displays how many times a zero bit will be inserted after 5 consecutive 1 bits when a frame from this pattern is sent out.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

frUniLtsPatOpStateTable 1.1.562.2.4.1.71.9.2.13
This group contains the attributes containing the operational statistics of the pattern.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrUniLtsPatOpStateEntry

frUniLtsPatOpStateEntry 1.1.562.2.4.1.71.9.2.13.1
An entry in the frUniLtsPatOpStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrUniLtsPatOpStateEntry  

frUniLtsPatLoad 1.1.562.2.4.1.71.9.2.13.1.200
This attribute indicates the load due to this particular pattern. The loads associated with all of the provisioned patterns are summed to arrive at the FrLts load.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FixedPoint3 0..4294967295  

frUniLtsPatStatus 1.1.562.2.4.1.71.9.2.13.1.201
This attributes specifies the administrative state of the pattern. A disabled pattern will not be generated, although it can still be triggered.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(0), disabled(1)  

frameRelayUniGroup 1.1.562.2.4.2.24.1
OBJECT IDENTIFIER    

frameRelayUniGroupBE 1.1.562.2.4.2.24.1.5
OBJECT IDENTIFIER    

frameRelayUniGroupBE01 1.1.562.2.4.2.24.1.5.2
OBJECT IDENTIFIER    

frameRelayUniGroupBE01A 1.1.562.2.4.2.24.1.5.2.2
OBJECT IDENTIFIER    

frameRelayUniCapabilities 1.1.562.2.4.2.24.3
OBJECT IDENTIFIER    

frameRelayUniCapabilitiesBE 1.1.562.2.4.2.24.3.5
OBJECT IDENTIFIER    

frameRelayUniCapabilitiesBE01 1.1.562.2.4.2.24.3.5.2
OBJECT IDENTIFIER    

frameRelayUniCapabilitiesBE01A 1.1.562.2.4.2.24.3.5.2.2
OBJECT IDENTIFIER