Nortel-Magellan-Passport-IpiFrMIB

File: Nortel-Magellan-Passport-IpiFrMIB.mib (103396 bytes)

Imported modules

RFC-1212	RFC1155-SMI	Nortel-Magellan-Passport-UsefulDefinitionsMIB
Nortel-Magellan-Passport-StandardTextualConventionsMIB	Nortel-Magellan-Passport-TextualConventionsMIB

Imported symbols

OBJECT-TYPE	IpAddress	components
passportMIBs	Counter32	RowPointer
DisplayString	StorageType	RowStatus
Integer32	Unsigned32	AsciiString
Hex	NonReplicated	HexString
EnterpriseDateAndTime	DigitString

Defined Types

IpiFrRowStatusEntry
SEQUENCE
	ipiFrRowStatus	RowStatus
	ipiFrComponentName	DisplayString
	ipiFrStorageType	StorageType
	ipiFrIndex	NonReplicated

IpiFrProvEntry
SEQUENCE
	ipiFrIpAddress	IpAddress
	ipiFrMaximumNumberOfLcn	Unsigned32
	ipiFrSubnetMask	IpAddress

IpiFrDnaRowStatusEntry
SEQUENCE
	ipiFrDnaRowStatus	RowStatus
	ipiFrDnaComponentName	DisplayString
	ipiFrDnaStorageType	StorageType
	ipiFrDnaIndex	NonReplicated

IpiFrDnaAddressEntry
SEQUENCE
	ipiFrDnaNumberingPlanIndicator	INTEGER
	ipiFrDnaDataNetworkAddress	DigitString

IpiFrDnaOutgoingOptionsEntry
SEQUENCE
	ipiFrDnaOutCalls	INTEGER
	ipiFrDnaOutDefaultPriority	INTEGER
	ipiFrDnaOutDefaultPathSensitivity	INTEGER
	ipiFrDnaOutPathSensitivityOverRide	INTEGER
	ipiFrDnaDefaultTransferPriority	INTEGER
	ipiFrDnaTransferPriorityOverRide	INTEGER

IpiFrDnaIncomingOptionsEntry
SEQUENCE
	ipiFrDnaIncCalls	INTEGER
	ipiFrDnaIncAccess	INTEGER

IpiFrDnaCallOptionsEntry
SEQUENCE
	ipiFrDnaServiceCategory	INTEGER
	ipiFrDnaAccountClass	Unsigned32
	ipiFrDnaServiceExchange	Unsigned32

IpiFrDnaCugRowStatusEntry
SEQUENCE
	ipiFrDnaCugRowStatus	RowStatus
	ipiFrDnaCugComponentName	DisplayString
	ipiFrDnaCugStorageType	StorageType
	ipiFrDnaCugIndex	Integer32

IpiFrDnaCugCugOptionsEntry
SEQUENCE
	ipiFrDnaCugType	INTEGER
	ipiFrDnaCugDnic	DigitString
	ipiFrDnaCugInterlockCode	Unsigned32
	ipiFrDnaCugIncCalls	INTEGER

IpiFrLcnRowStatusEntry
SEQUENCE
	ipiFrLcnRowStatus	RowStatus
	ipiFrLcnComponentName	DisplayString
	ipiFrLcnStorageType	StorageType
	ipiFrLcnIndex	Integer32

IpiFrLcnStateEntry
SEQUENCE
	ipiFrLcnAdminState	INTEGER
	ipiFrLcnOperationalState	INTEGER
	ipiFrLcnUsageState	INTEGER
	ipiFrLcnAvailabilityStatus	OCTET STRING
	ipiFrLcnProceduralStatus	OCTET STRING
	ipiFrLcnControlStatus	OCTET STRING
	ipiFrLcnAlarmStatus	OCTET STRING
	ipiFrLcnStandbyStatus	INTEGER
	ipiFrLcnUnknownStatus	INTEGER

IpiFrLcnOperEntry
SEQUENCE
	ipiFrLcnIpInterfaceDevice	INTEGER
	ipiFrLcnOpRemoteIpAddress	IpAddress
	ipiFrLcnPacketsSent	Counter32
	ipiFrLcnPacketsReceived	Counter32
	ipiFrLcnDiscardTxPackets	Counter32
	ipiFrLcnDiscardRcvPackets	Counter32

IpiFrLcnProvEntry
SEQUENCE
	ipiFrLcnRemoteIpAddress	IpAddress

IpiFrLcnDcRowStatusEntry
SEQUENCE
	ipiFrLcnDcRowStatus	RowStatus
	ipiFrLcnDcComponentName	DisplayString
	ipiFrLcnDcStorageType	StorageType
	ipiFrLcnDcIndex	NonReplicated

IpiFrLcnDcOptionsEntry
SEQUENCE
	ipiFrLcnDcRemoteNpi	INTEGER
	ipiFrLcnDcRemoteDna	DigitString
	ipiFrLcnDcRemoteDlci	Unsigned32
	ipiFrLcnDcType	INTEGER
	ipiFrLcnDcTransferPriority	INTEGER
	ipiFrLcnDcDiscardPriority	INTEGER

IpiFrLcnDcNfaEntry
SEQUENCE
	ipiFrLcnDcNfaIndex	Integer32
	ipiFrLcnDcNfaValue	HexString
	ipiFrLcnDcNfaRowStatus	RowStatus

IpiFrLcnVcRowStatusEntry
SEQUENCE
	ipiFrLcnVcRowStatus	RowStatus
	ipiFrLcnVcComponentName	DisplayString
	ipiFrLcnVcStorageType	StorageType
	ipiFrLcnVcIndex	NonReplicated

IpiFrLcnVcCadEntry
SEQUENCE
	ipiFrLcnVcType	INTEGER
	ipiFrLcnVcState	INTEGER
	ipiFrLcnVcPreviousState	INTEGER
	ipiFrLcnVcDiagnosticCode	Unsigned32
	ipiFrLcnVcPreviousDiagnosticCode	Unsigned32
	ipiFrLcnVcCalledNpi	INTEGER
	ipiFrLcnVcCalledDna	DigitString
	ipiFrLcnVcCalledLcn	Unsigned32
	ipiFrLcnVcCallingNpi	INTEGER
	ipiFrLcnVcCallingDna	DigitString
	ipiFrLcnVcCallingLcn	Unsigned32
	ipiFrLcnVcAccountingEnabled	INTEGER
	ipiFrLcnVcFastSelectCall	INTEGER
	ipiFrLcnVcPathReliability	INTEGER
	ipiFrLcnVcAccountingEnd	INTEGER
	ipiFrLcnVcPriority	INTEGER
	ipiFrLcnVcSegmentSize	Unsigned32
	ipiFrLcnVcMaxSubnetPktSize	Unsigned32
	ipiFrLcnVcRcosToNetwork	INTEGER
	ipiFrLcnVcRcosFromNetwork	INTEGER
	ipiFrLcnVcEmissionPriorityToNetwork	INTEGER
	ipiFrLcnVcEmissionPriorityFromNetwork	INTEGER
	ipiFrLcnVcDataPath	AsciiString

IpiFrLcnVcIntdEntry
SEQUENCE
	ipiFrLcnVcCallReferenceNumber	Hex
	ipiFrLcnVcElapsedTimeTillNow	Unsigned32
	ipiFrLcnVcSegmentsRx	Unsigned32
	ipiFrLcnVcSegmentsSent	Unsigned32
	ipiFrLcnVcStartTime	EnterpriseDateAndTime

IpiFrLcnVcFrdEntry
SEQUENCE
	ipiFrLcnVcFrmCongestedToSubnet	Unsigned32
	ipiFrLcnVcCannotForwardToSubnet	Unsigned32
	ipiFrLcnVcNotDataXferToSubnet	Unsigned32
	ipiFrLcnVcOutOfRangeFrmFromSubnet	Unsigned32
	ipiFrLcnVcCombErrorsFromSubnet	Unsigned32
	ipiFrLcnVcDuplicatesFromSubnet	Unsigned32
	ipiFrLcnVcNotDataXferFromSubnet	Unsigned32
	ipiFrLcnVcFrmLossTimeouts	Unsigned32
	ipiFrLcnVcOoSeqByteCntExceeded	Unsigned32
	ipiFrLcnVcPeakOoSeqPktCount	Unsigned32
	ipiFrLcnVcPeakOoSeqFrmForwarded	Unsigned32
	ipiFrLcnVcSendSequenceNumber	Unsigned32
	ipiFrLcnVcPktRetryTimeouts	Unsigned32
	ipiFrLcnVcPeakRetryQueueSize	Unsigned32
	ipiFrLcnVcSubnetRecoveries	Unsigned32
	ipiFrLcnVcOoSeqPktCntExceeded	Unsigned32
	ipiFrLcnVcPeakOoSeqByteCount	Unsigned32

IpiFrLcnVcDmepEntry
SEQUENCE
	ipiFrLcnVcDmepValue	RowPointer

IpiFrSrRowStatusEntry
SEQUENCE
	ipiFrSrRowStatus	RowStatus
	ipiFrSrComponentName	DisplayString
	ipiFrSrStorageType	StorageType
	ipiFrSrIndex	IpAddress

IpiFrSrProvEntry
SEQUENCE
	ipiFrSrGatewayIpAddress	IpAddress

IpiFrSrBGtyIpaEntry
SEQUENCE
	ipiFrSrBGtyIpaIndex	Integer32
	ipiFrSrBGtyIpaValue	IpAddress
	ipiFrSrBGtyIpaRowStatus	RowStatus

IpiFrRRowStatusEntry
SEQUENCE
	ipiFrRRowStatus	RowStatus
	ipiFrRComponentName	DisplayString
	ipiFrRStorageType	StorageType
	ipiFrRIndex	IpAddress

IpiFrROperEntry
SEQUENCE
	ipiFrRGtyIpAddr	IpAddress
	ipiFrRLcnIf	Unsigned32
	ipiFrRType	INTEGER

Defined Values

ipiFrMIB		1.3.6.1.4.1.562.2.4.2.35
OBJECT IDENTIFIER

ipiFr		1.3.6.1.4.1.562.2.4.1.50
OBJECT IDENTIFIER

ipiFrRowStatusTable		1.3.6.1.4.1.562.2.4.1.50.1
This entry controls the addition and deletion of ipiFr components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrRowStatusEntry

ipiFrRowStatusEntry		1.3.6.1.4.1.562.2.4.1.50.1.1
A single entry in the table represents a single ipiFr component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrRowStatusEntry

ipiFrRowStatus		1.3.6.1.4.1.562.2.4.1.50.1.1.1
This variable is used as the basis for SNMP naming of ipiFr components. These components can be added and deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

ipiFrComponentName		1.3.6.1.4.1.562.2.4.1.50.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

ipiFrStorageType		1.3.6.1.4.1.562.2.4.1.50.1.1.4
This variable represents the storage type value for the ipiFr tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

ipiFrIndex		1.3.6.1.4.1.562.2.4.1.50.1.1.10
This variable represents the index for the ipiFr tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NonReplicated

ipiFrProvTable		1.3.6.1.4.1.562.2.4.1.50.10
This group provides the provisionable attributes for the IpiFr component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrProvEntry

ipiFrProvEntry		1.3.6.1.4.1.562.2.4.1.50.10.1
An entry in the ipiFrProvTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrProvEntry

ipiFrIpAddress		1.3.6.1.4.1.562.2.4.1.50.10.1.1
This attribute specifies the unique Internet Protocol (IP) Address that represents the IP address of the IPI service.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipiFrMaximumNumberOfLcn		1.3.6.1.4.1.562.2.4.1.50.10.1.2
This attribute specifies the maximum number of LCNs that are supported on this service. It specifies the maximum number of connections from external network management sites to this IpiFr service.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	24

ipiFrSubnetMask		1.3.6.1.4.1.562.2.4.1.50.10.1.3
This attribute specifies the subnetwork mask for the IPI service.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipiFrDna		1.3.6.1.4.1.562.2.4.1.50.2
OBJECT IDENTIFIER

ipiFrDnaRowStatusTable		1.3.6.1.4.1.562.2.4.1.50.2.1
This entry controls the addition and deletion of ipiFrDna components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrDnaRowStatusEntry

ipiFrDnaRowStatusEntry		1.3.6.1.4.1.562.2.4.1.50.2.1.1
A single entry in the table represents a single ipiFrDna component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrDnaRowStatusEntry

ipiFrDnaRowStatus		1.3.6.1.4.1.562.2.4.1.50.2.1.1.1
This variable is used as the basis for SNMP naming of ipiFrDna components. These components cannot be added nor deleted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	RowStatus

ipiFrDnaComponentName		1.3.6.1.4.1.562.2.4.1.50.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

ipiFrDnaStorageType		1.3.6.1.4.1.562.2.4.1.50.2.1.1.4
This variable represents the storage type value for the ipiFrDna tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

ipiFrDnaIndex		1.3.6.1.4.1.562.2.4.1.50.2.1.1.10
This variable represents the index for the ipiFrDna tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NonReplicated

ipiFrDnaAddressTable		1.3.6.1.4.1.562.2.4.1.50.2.10
Address group contains attributes common to all Dna's. Every Dna used in the network is defined with this group of 2 attributes. String of address digits is complemented by type of address and Npi. These attributes are used to interpret format of the address digits.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrDnaAddressEntry

ipiFrDnaAddressEntry		1.3.6.1.4.1.562.2.4.1.50.2.10.1
An entry in the ipiFrDnaAddressTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrDnaAddressEntry

ipiFrDnaNumberingPlanIndicator		1.3.6.1.4.1.562.2.4.1.50.2.10.1.1
This attribute indicates the Numbering Plan Indicator (NPI) of the Dna that is entered. Address may belong to X.121 or E.164 plans. X.121 is used in packet svitched data networks.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	x121(0), e164(1)

ipiFrDnaDataNetworkAddress		1.3.6.1.4.1.562.2.4.1.50.2.10.1.2
Dna attribute contains digits which form unique identifier of the customer interface. It can be compared (approximation only) to telephone number where phone number identifies unique telephone set. Dna digits are selected and assigned by network operators. MaximumLenOfDna is 15digits.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DigitString	Size(1..15)

ipiFrDnaOutgoingOptionsTable		1.3.6.1.4.1.562.2.4.1.50.2.11
OutgoingOptions group defines call options of a Dna for calls which are made out of the interface represented by Dna. All these options are not used for calls arriving to the interface represented by Dna.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrDnaOutgoingOptionsEntry

ipiFrDnaOutgoingOptionsEntry		1.3.6.1.4.1.562.2.4.1.50.2.11.1
An entry in the ipiFrDnaOutgoingOptionsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrDnaOutgoingOptionsEntry

ipiFrDnaOutCalls		1.3.6.1.4.1.562.2.4.1.50.2.11.1.1
This attribute, if set to a value of allowed indicates that outgoing calls (from the DTE to the network) can be made using this particular Dna. If set to a value of disallowed , then outgoing calls cannot be made using this Dna - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Outgoing Calls Barred' feature for Dnas in that outgoing calls are barred if this attribute is set to a value of disallowed. Either outCalls, or incCalls (or both) must be set to a value of allowed for this Dna to be useable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disallowed(0), allowed(1)

ipiFrDnaOutDefaultPriority		1.3.6.1.4.1.562.2.4.1.50.2.11.1.7
This attribute, if set to normal indicates that the default priority for outgoing calls (from the DTE to the network) using this particular Dna is normal priority - if the priority is not specified by the DTE. If this attribute is set to high then the default priority for outgoing calls using this particular Dna is high priority. It can be overridden by the discardPriority under DLCI Direct Call subcomponent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	normal(0), high(1)

ipiFrDnaOutDefaultPathSensitivity		1.3.6.1.4.1.562.2.4.1.50.2.11.1.11
This attribute specifies the default class of path sensitivity to network for all outgoing calls using this particular Dna. The chosen default class of path sensitivity applies to all outgoing calls established using this Dna. This attribute, if set to a value of throughput, indicates that the default class is throughput sensitive. If set to a value of delay, then the default class is delay sensitive. The default of outDefaultPathSensitivity is delay.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	throughput(0), delay(1)

ipiFrDnaOutPathSensitivityOverRide		1.3.6.1.4.1.562.2.4.1.50.2.11.1.12
If this attribute is set to in the call request, the called end will use the calling end provisioning data on path sensitivity to override its own provisioning data. The default of outPathSensitivityOverRide is yes.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

ipiFrDnaDefaultTransferPriority		1.3.6.1.4.1.562.2.4.1.50.2.11.1.18
This attribute specifies the default transfer priority to network for all outgoing calls using this particular Dna. It is overRidden by the transferPriority provisioned in the DLCI Direct Call sub- component. The transfer priority is a preference specified by an application according to its delay-sensitivity requirement. Frames with high transfer priority are served by the network before the frames with normal priority. Each transfer priority contains a predetermined setting for trunk queue (interrupting, delay or throughput), routing metric (delay or throughput). When the transfer priority is set at high, the trunk queue is set to high, the routing metric is set to delay. When the transfer priority is set at normal, the trunk queue is set to normal, the routing metric is set to throughput. The default of defaultTransferPriority is high.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(0), high(9)

ipiFrDnaTransferPriorityOverRide		1.3.6.1.4.1.562.2.4.1.50.2.11.1.19
When this attribute is set to yes, the called end will use the calling end provisioning data on transfer priority to override its own provisioning data. If it is set no, the called end will use its own provisioning data on transfer priority. For more information about transfer priority, please refer to the previous attribute defaultTransferPriority. The default of transferPriorityOverRide is yes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

ipiFrDnaIncomingOptionsTable		1.3.6.1.4.1.562.2.4.1.50.2.12
IncomingOptions defines set of options for incoming calls. These options are used for calls arriving to the interface represented by Dna. For calls originated from the interfasce, IncomingOptions attributes are not used.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrDnaIncomingOptionsEntry

ipiFrDnaIncomingOptionsEntry		1.3.6.1.4.1.562.2.4.1.50.2.12.1
An entry in the ipiFrDnaIncomingOptionsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrDnaIncomingOptionsEntry

ipiFrDnaIncCalls		1.3.6.1.4.1.562.2.4.1.50.2.12.1.1
This attribute, if set to a value of allowed indicates that incoming calls (from the network to the DTE) can be made to this Dna. If set to a value of disallowed, then incoming calls cannot be made to this Dna - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Incoming Calls Barred' feature for Dna's in that incoming calls are barred if this attribute is set to a value of disallowed. Either outCalls, or incCalls (or both) must be set to a value of allowed for this Dna to be useable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disallowed(0), allowed(1)

ipiFrDnaIncAccess		1.3.6.1.4.1.562.2.4.1.50.2.12.1.9
This attribute is an extension of the Closed User Group (CUG) facility, as follows: This attribute, if set to a value of allowed indicates that incoming calls (from the network to the DTE) from the open (non-CUG) part of the network are permitted. It also permits incoming calls from DTEs that have Outgoing Access capabilities. If set to a value of disallowed, then such calls cannot be made to this Dna - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Closed User Group with Incoming Access' feature for Dnas in that incoming access is granted if this attribute is set to a value of allowed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disallowed(0), allowed(1)

ipiFrDnaCallOptionsTable		1.3.6.1.4.1.562.2.4.1.50.2.13
CallOptions group defines additional options for calls not related directly to direction of a call.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrDnaCallOptionsEntry

ipiFrDnaCallOptionsEntry		1.3.6.1.4.1.562.2.4.1.50.2.13.1
An entry in the ipiFrDnaCallOptionsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrDnaCallOptionsEntry

ipiFrDnaServiceCategory		1.3.6.1.4.1.562.2.4.1.50.2.13.1.1
This attribute is assigned for each different type of service within which this Dna is configured. It is placed into the Service Category attribute in the accounting record by both ends of the Vc.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	gsp(0), x25(1), enhancedIti(2), ncs(3), mlti(4), sm(5), ici(6), dsp3270(7), iam(8), mlhi(9), term3270(10), iti(11), bsi(13), hostIti(14), x75(15), hdsp3270(16), api3201(20), sdlc(21), snaMultiHost(22), redirectionServ(23), trSnaTpad(24), offnetNui(25), gasServer(26), vapServer(28), vapAgent(29), frameRelay(30), ipiVc(31), ipiFr(32)

ipiFrDnaAccountClass		1.3.6.1.4.1.562.2.4.1.50.2.13.1.10
This attribute specifies the accounting class which is reserved for network operations usage. Its value is returned in the accounting record in the local and remote service type attributes. Use of this attribute is decided by network operator and it is an arbitrary number.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0..255

ipiFrDnaServiceExchange		1.3.6.1.4.1.562.2.4.1.50.2.13.1.12
This attribute is an arbitrary number, entered by the network operator. It is included in the accounting record created by Vc.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0..255

ipiFrDnaCug		1.3.6.1.4.1.562.2.4.1.50.2.2
OBJECT IDENTIFIER

ipiFrDnaCugRowStatusTable		1.3.6.1.4.1.562.2.4.1.50.2.2.1
This entry controls the addition and deletion of ipiFrDnaCug components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrDnaCugRowStatusEntry

ipiFrDnaCugRowStatusEntry		1.3.6.1.4.1.562.2.4.1.50.2.2.1.1
A single entry in the table represents a single ipiFrDnaCug component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrDnaCugRowStatusEntry

ipiFrDnaCugRowStatus		1.3.6.1.4.1.562.2.4.1.50.2.2.1.1.1
This variable is used as the basis for SNMP naming of ipiFrDnaCug components. These components can be added and deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

ipiFrDnaCugComponentName		1.3.6.1.4.1.562.2.4.1.50.2.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

ipiFrDnaCugStorageType		1.3.6.1.4.1.562.2.4.1.50.2.2.1.1.4
This variable represents the storage type value for the ipiFrDnaCug tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

ipiFrDnaCugIndex		1.3.6.1.4.1.562.2.4.1.50.2.2.1.1.10
This variable represents the index for the ipiFrDnaCug tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

ipiFrDnaCugCugOptionsTable		1.3.6.1.4.1.562.2.4.1.50.2.2.10
This group defines options for a CUG. Attributes in this group define ClosedUserGroup options associated with interlockCode. DNA's with the same CUG (interlockCode) can make calls within this group. Various combinations which permit or prevent calls in the same CUG group are defined here.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrDnaCugCugOptionsEntry

ipiFrDnaCugCugOptionsEntry		1.3.6.1.4.1.562.2.4.1.50.2.2.10.1
An entry in the ipiFrDnaCugCugOptionsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrDnaCugCugOptionsEntry

ipiFrDnaCugType		1.3.6.1.4.1.562.2.4.1.50.2.2.10.1.1
This attribute specifies the CUG type - the CUG is either a national CUG, or an international CUG. International closed user groups are usually established between DTEs for which there is an X.75 Gateway between; whereas national closed user groups are usually established between DTEs for which there is no X.75 Gateway between. (National CUGs cannot normally traverse an X.75 Gateway). If this attribute is set to national, then the CUG is a national CUG, in which case, the dnic should be left at its default value since it is not part of a national CUG. If this attribute is set to international, then the CUG is an international CUG, in which case, the dnic should be set appropriately as part of the CUG interlockCode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	national(0), international(1)

ipiFrDnaCugDnic		1.3.6.1.4.1.562.2.4.1.50.2.2.10.1.2
This attribute specifies the dnic (Data Network ID Code) of the CUG by which packet networks are identified. This attribute is not applicable if the CUG is a national CUG, as specified by the CUG type attribute. There are usually 1 or 2 dnics assigned per country, for public networks. The U.S. is an exception where each BOC has a dnic. Also, a group of private networks can have its own dnic. dnic value is not an arbitrary number. It is assigned by international agreement and controlled by CCITT.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DigitString	Size(4)

ipiFrDnaCugInterlockCode		1.3.6.1.4.1.562.2.4.1.50.2.2.10.1.3
This attribute specifies the CUG identifier of a national or international CUG call. It is an arbitrary number and it also can be called CUG in some descriptions. Interfaces (DNA's) defined with this number can make calls to DNA's with the same interlockCode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	0..65535

ipiFrDnaCugIncCalls		1.3.6.1.4.1.562.2.4.1.50.2.2.10.1.6
This attribute, if set to allowed indicates that incoming calls (from the network to the DTE) can be made using this particular CUG. If set to disallowed, then incoming calls cannot be made using this CUG - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Incoming Calls Barred' feature for CUGs in that incoming calls are barred if this attribute is set to a value of disallowed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disallowed(0), allowed(1)

ipiFrLcn		1.3.6.1.4.1.562.2.4.1.50.4
OBJECT IDENTIFIER

ipiFrLcnRowStatusTable		1.3.6.1.4.1.562.2.4.1.50.4.1
This entry controls the addition and deletion of ipiFrLcn components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrLcnRowStatusEntry

ipiFrLcnRowStatusEntry		1.3.6.1.4.1.562.2.4.1.50.4.1.1
A single entry in the table represents a single ipiFrLcn component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrLcnRowStatusEntry

ipiFrLcnRowStatus		1.3.6.1.4.1.562.2.4.1.50.4.1.1.1
This variable is used as the basis for SNMP naming of ipiFrLcn components. These components can be added and deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

ipiFrLcnComponentName		1.3.6.1.4.1.562.2.4.1.50.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

ipiFrLcnStorageType		1.3.6.1.4.1.562.2.4.1.50.4.1.1.4
This variable represents the storage type value for the ipiFrLcn tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

ipiFrLcnIndex		1.3.6.1.4.1.562.2.4.1.50.4.1.1.10
This variable represents the index for the ipiFrLcn tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Integer32	16..39

ipiFrLcnStateTable		1.3.6.1.4.1.562.2.4.1.50.4.10
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrLcnStateEntry

ipiFrLcnStateEntry		1.3.6.1.4.1.562.2.4.1.50.4.10.1
An entry in the ipiFrLcnStateTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrLcnStateEntry

ipiFrLcnAdminState		1.3.6.1.4.1.562.2.4.1.50.4.10.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	locked(0), unlocked(1), shuttingDown(2)

ipiFrLcnOperationalState		1.3.6.1.4.1.562.2.4.1.50.4.10.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

ipiFrLcnUsageState		1.3.6.1.4.1.562.2.4.1.50.4.10.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	idle(0), active(1), busy(2)

ipiFrLcnAvailabilityStatus		1.3.6.1.4.1.562.2.4.1.50.4.10.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(2)

ipiFrLcnProceduralStatus		1.3.6.1.4.1.562.2.4.1.50.4.10.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

ipiFrLcnControlStatus		1.3.6.1.4.1.562.2.4.1.50.4.10.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

ipiFrLcnAlarmStatus		1.3.6.1.4.1.562.2.4.1.50.4.10.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

ipiFrLcnStandbyStatus		1.3.6.1.4.1.562.2.4.1.50.4.10.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hotStandby(0), coldStandby(1), providingService(2), notSet(15)

ipiFrLcnUnknownStatus		1.3.6.1.4.1.562.2.4.1.50.4.10.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	false(0), true(1)

ipiFrLcnOperTable		1.3.6.1.4.1.562.2.4.1.50.4.11
This group contains status of the internal IP network interface.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrLcnOperEntry

ipiFrLcnOperEntry		1.3.6.1.4.1.562.2.4.1.50.4.11.1
An entry in the ipiFrLcnOperTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrLcnOperEntry

ipiFrLcnIpInterfaceDevice		1.3.6.1.4.1.562.2.4.1.50.4.11.1.1
The status of the internal IP network interface is inactive until either the remoteIpAddress attribute is provisioned, or an IP packet is exchanged between a Network Management Station and the internal IP network interface (via the LCN). At this point, the status changes to active.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	inactive(0), active(1)

ipiFrLcnOpRemoteIpAddress		1.3.6.1.4.1.562.2.4.1.50.4.11.1.2
This attribute indicates the IP address of the remote network device connected to this interface. The value is either 0.0.0.0 until the frist data packe tis received from the remote end, or is the value provisioned in remoteIpAddress.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IpAddress

ipiFrLcnPacketsSent		1.3.6.1.4.1.562.2.4.1.50.4.11.1.3
This attribute counts the number of IP packets sent from this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

ipiFrLcnPacketsReceived		1.3.6.1.4.1.562.2.4.1.50.4.11.1.4
This attribute counts the number of IP packets received from the remote network device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

ipiFrLcnDiscardTxPackets		1.3.6.1.4.1.562.2.4.1.50.4.11.1.5
This attribute counts the number of IP packets destined to the remote end which were discarded by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

ipiFrLcnDiscardRcvPackets		1.3.6.1.4.1.562.2.4.1.50.4.11.1.6
This attribute counts the number of IP packets received from the remote end which were discarded by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

ipiFrLcnProvTable		1.3.6.1.4.1.562.2.4.1.50.4.12
This group provides the provisionable attributes for the IpiFR Lcn component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrLcnProvEntry

ipiFrLcnProvEntry		1.3.6.1.4.1.562.2.4.1.50.4.12.1
An entry in the ipiFrLcnProvTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrLcnProvEntry

ipiFrLcnRemoteIpAddress		1.3.6.1.4.1.562.2.4.1.50.4.12.1.1
This attribute specifies the IP address of the remote device connected to this Lcn interface. This device can be a host, and / or a gateway. If the device is a gateway, and StaticRoutes are defined using this gateway, it is recommended that this attribute be set. It is also recommended to set this attribute, if management applications such as Software Download and SNMP, which can initiate IP traffic with Network Management Stations, are potentially using this Lcn interface. IP routing information within IpiFr is not known or activated for this Lcn interface until the remoteIpAddress is known. When the destination IpAddress is left at its default value of 0.0.0.0, the calling IP address is learnt from the first data packet received.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipiFrLcnDc		1.3.6.1.4.1.562.2.4.1.50.4.2
OBJECT IDENTIFIER

ipiFrLcnDcRowStatusTable		1.3.6.1.4.1.562.2.4.1.50.4.2.1
This entry controls the addition and deletion of ipiFrLcnDc components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrLcnDcRowStatusEntry

ipiFrLcnDcRowStatusEntry		1.3.6.1.4.1.562.2.4.1.50.4.2.1.1
A single entry in the table represents a single ipiFrLcnDc component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrLcnDcRowStatusEntry

ipiFrLcnDcRowStatus		1.3.6.1.4.1.562.2.4.1.50.4.2.1.1.1
This variable is used as the basis for SNMP naming of ipiFrLcnDc components. These components cannot be added nor deleted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	RowStatus

ipiFrLcnDcComponentName		1.3.6.1.4.1.562.2.4.1.50.4.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

ipiFrLcnDcStorageType		1.3.6.1.4.1.562.2.4.1.50.4.2.1.1.4
This variable represents the storage type value for the ipiFrLcnDc tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

ipiFrLcnDcIndex		1.3.6.1.4.1.562.2.4.1.50.4.2.1.1.10
This variable represents the index for the ipiFrLcnDc tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NonReplicated

ipiFrLcnDcOptionsTable		1.3.6.1.4.1.562.2.4.1.50.4.2.10
Options group defines attributes associated with direct call. It defines complete connection in terms of path and call options. This connection can be permanent (pvc) or, in future release, switched (svc). It can have facilities. The total number of bytes of facilities including the facility codes, and all of the facility data from all of the four classes of facilities: CCITT_Facilities DTE_Facilities National_Facilities International_Facilities must not exceed 512 bytes.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrLcnDcOptionsEntry

ipiFrLcnDcOptionsEntry		1.3.6.1.4.1.562.2.4.1.50.4.2.10.1
An entry in the ipiFrLcnDcOptionsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrLcnDcOptionsEntry

ipiFrLcnDcRemoteNpi		1.3.6.1.4.1.562.2.4.1.50.4.2.10.1.3
RemoteNumbering Plan Indicator (Npi) indicates the numbering plan used in the remoteDna.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	x121(0), e164(1)

ipiFrLcnDcRemoteDna		1.3.6.1.4.1.562.2.4.1.50.4.2.10.1.4
This attribute specifies the Data Network Address (Dna) of the remote. This is the called (destination) DTE address (Dna) to which this direct call will be sent. Initially, the called DTE address attribute must be present, that is, there must be a valid destination address. However, it may be possible in the future to configure the direct call with a mnemonic address, in which case, this attribute will contain a zero-length Dna, and the mnemonic address will be carried as one of the facilities.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DigitString	Size(1..15)

ipiFrLcnDcRemoteDlci		1.3.6.1.4.1.562.2.4.1.50.4.2.10.1.5
This attribute provides the value of the remote DLCI (Data Link Connection Identifier)
Status: mandatory	Access: read-write
OBJECT-TYPE
	Unsigned32	16..1007

ipiFrLcnDcType		1.3.6.1.4.1.562.2.4.1.50.4.2.10.1.6
This attribute specifies the type of Vc call: permanentMaster, permanentSlave, If the value is set to permanentMaster, then a permanent connection will be established between 2 ends. The remote end must be defined as a permanentSlave, permanentBackupSlave or permanentSlaveWithBackup. The connection cannot be established if the remote end is defined as anything else. The end defined as permanentMaster always initiates the calls. It will attempt to call once per minute. If the value is set to permanentSlave then a permanent connection will be established between 2 ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote end is defined as anything else. The permanentSlave end will attempt to call once per minute.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	permanentMaster(1), permanentSlave(2)

ipiFrLcnDcTransferPriority		1.3.6.1.4.1.562.2.4.1.50.4.2.10.1.9
This attribute specifies the transfer priority to network for the outgoing calls using this particular DLCI. It overRides the defaultTransferPriority provisioned in its associated Dna component. The transfer priority is a preference specified by an application according to its delay-sensitivity requirement. Frames with high transfer priority are served by the network before the frames with normal priority. Each transfer priority contains a predetermined setting for trunk queue (interrupting, delay or throughput), routing metric (delay or throughput). When the transfer priority is set at high, the trunk queue is set to high, the routing metric is set to delay. When the transfer priority is set at normal, the trunk queue is set to normal, the routing metric is set to throughput. The default of transferPriority is useDnaDefTP. It means using the provisioning value under defaultTransferPriority of its associated Dna for this DLCI.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(0), high(9), useDnaDefTP(255)

ipiFrLcnDcDiscardPriority		1.3.6.1.4.1.562.2.4.1.50.4.2.10.1.10
This attribute specifies the discard priority for outgoing call using this DLCI. The discard priority has three provisioning values: normal, high, and useDnaDefPriority. Traffic with normal priority are discarded first than the traffic with high priority. The Dna default value (provisioned by outDefaultPriority) is taken if this attribute is set to the value useDnaDefPriority. The default of discardPriority is useDnaDefPriority.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(0), high(1), useDnaDefPriority(3)

ipiFrLcnDcNfaTable		1.3.6.1.4.1.562.2.4.1.50.4.2.222
This is the i'th National facility required for this direct call. Within the provisioning system, the user specifies the facility code along with the facility parameters. The facility is represented internally as a hexadecimal string following the X.25 CCITT representation for facility data. Two explicit attributes discardPriority and transferPriority are created to replace H.01 and H.30 in the group VcsDirectCallOptionsProv of this file. The migrate escape here (DcComponent::migrateFaxEscape) propagates the old provisioning data under H.01. The rule of the above propagation are: 0 in H.01 is equivalent to discardPriority 0; 1 in H.01 is equivalent to discardPriority 1. And 0 in H.30 is equivalent to transferPriority normal; 1 in H.30 is equivalent to transferPriority high. Please refer to discardPriority and transferPriority for more information on how to use them.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrLcnDcNfaEntry

ipiFrLcnDcNfaEntry		1.3.6.1.4.1.562.2.4.1.50.4.2.222.1
An entry in the ipiFrLcnDcNfaTable.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	IpiFrLcnDcNfaEntry

ipiFrLcnDcNfaIndex		1.3.6.1.4.1.562.2.4.1.50.4.2.222.1.1
This variable represents the index for the ipiFrLcnDcNfaTable.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	Integer32	1

ipiFrLcnDcNfaValue		1.3.6.1.4.1.562.2.4.1.50.4.2.222.1.2
This variable represents an individual value for the ipiFrLcnDcNfaTable.
Status: obsolete	Access: read-write
OBJECT-TYPE
	HexString	Size(0..128)

ipiFrLcnDcNfaRowStatus		1.3.6.1.4.1.562.2.4.1.50.4.2.222.1.3
This variable is used to control the addition and deletion of individual values of the ipiFrLcnDcNfaTable.
Status: obsolete	Access: write-only
OBJECT-TYPE
	RowStatus

ipiFrLcnVc		1.3.6.1.4.1.562.2.4.1.50.4.3
OBJECT IDENTIFIER

ipiFrLcnVcRowStatusTable		1.3.6.1.4.1.562.2.4.1.50.4.3.1
This entry controls the addition and deletion of ipiFrLcnVc components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrLcnVcRowStatusEntry

ipiFrLcnVcRowStatusEntry		1.3.6.1.4.1.562.2.4.1.50.4.3.1.1
A single entry in the table represents a single ipiFrLcnVc component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrLcnVcRowStatusEntry

ipiFrLcnVcRowStatus		1.3.6.1.4.1.562.2.4.1.50.4.3.1.1.1
This variable is used as the basis for SNMP naming of ipiFrLcnVc components. These components cannot be added nor deleted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	RowStatus

ipiFrLcnVcComponentName		1.3.6.1.4.1.562.2.4.1.50.4.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

ipiFrLcnVcStorageType		1.3.6.1.4.1.562.2.4.1.50.4.3.1.1.4
This variable represents the storage type value for the ipiFrLcnVc tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

ipiFrLcnVcIndex		1.3.6.1.4.1.562.2.4.1.50.4.3.1.1.10
This variable represents the index for the ipiFrLcnVc tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NonReplicated

ipiFrLcnVcCadTable		1.3.6.1.4.1.562.2.4.1.50.4.3.10
This group represents operational call data related to Frame Relay Vc. It can be displayed only for Frame Relay Vc which is created by application.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrLcnVcCadEntry

ipiFrLcnVcCadEntry		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1
An entry in the ipiFrLcnVcCadTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrLcnVcCadEntry

ipiFrLcnVcType		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.1
This attribute displays the type of call, pvc,svc or spvc.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	svc(0), pvc(1), spvc(2)

ipiFrLcnVcState		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.2
This attribute displays the state of call control. P5 state is not supported but is listed for completness. Transitions from one state to another take very short time. state most often displayed is dataTransferP4.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	creating(0), readyP1(1), dteWaitingP2(2), dceWaitingP3(3), dataTransferP4(4), unsupportedP5(5), dteClearRequestP6(6), dceClearIndicationP7(7), termination(8)

ipiFrLcnVcPreviousState		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.3
This attribute displays the previous state of call control. This is a valuable field to determine how the processing is progressing.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	creating(0), readyP1(1), dteWaitingP2(2), dceWaitingP3(3), dataTransferP4(4), unsupportedP5(5), dteClearRequestP6(6), dceClearIndicationP7(7), termination(8)

ipiFrLcnVcDiagnosticCode		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.4
This attribute displays the internal substate of call control. It is used to further refine state of call processing.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..255

ipiFrLcnVcPreviousDiagnosticCode		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.5
This attribute displays the internal substate of call control. It is used to further refine state of call processing.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..255

ipiFrLcnVcCalledNpi		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.6
This attribute displays the Numbering Plan Indicator (NPI) of the called end.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	x121(0), e164(1)

ipiFrLcnVcCalledDna		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.7
This attribute displays the Data Network Address (Dna) of the called (destination) DTE to which this call is sent. This address if defined at recieving end will complete Vc connection.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DigitString	Size(1..15)

ipiFrLcnVcCalledLcn		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.8
This attribute displays the Logical Channel Number of the called end. It is valid only after both ends of Vc exchanged relevant information.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	1..65535

ipiFrLcnVcCallingNpi		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.9
This attribute displays the Numbering Plan Indicator (NPI) of the calling end.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	x121(0), e164(1)

ipiFrLcnVcCallingDna		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.10
This attribute displays the Data Network Address (Dna) of the calling end.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DigitString	Size(1..15)

ipiFrLcnVcCallingLcn		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.11
This attribute displays the Logical Channel Number of the calling end.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	1..65535

ipiFrLcnVcAccountingEnabled		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.12
This attribute indicates that this optional section of accounting record is suppressed or permitted. If accountingEnabled is yes, conditions for generation of accounting record were met. These conditions include billing options, vc recovery conditions and Module wide accounting data options.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	yes(0), no(1)

ipiFrLcnVcFastSelectCall		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.13
This attribute displays that this is a fast select call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	no(0), yes(1)

ipiFrLcnVcPathReliability		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.19
This attribute displays the path reliability.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	high(0), normal(1)

ipiFrLcnVcAccountingEnd		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.20
This attribute indicates if this end should generate an accounting record. Normally, callingEnd is the end to generate an accounting record.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	callingEnd(0), calledEnd(1)

ipiFrLcnVcPriority		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.21
This attribute displays whether the call is a normal or a high priority call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	normal(0), high(1)

ipiFrLcnVcSegmentSize		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.22
This attribute displays the segment size (in bytes) used on the call. It is used to calculate the number of segments transmitted and received.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4096

ipiFrLcnVcMaxSubnetPktSize		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.27
This attribute indicates the maximum packet size allowed on the Vc.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4096

ipiFrLcnVcRcosToNetwork		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.28
This attribute indicates the routing metric routing class of service to the network.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	throughput(0), delay(1), multimedia(2)

ipiFrLcnVcRcosFromNetwork		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.29
This attribute displays the routing metric Routing Class of Service from the Network.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	throughput(0), delay(1), multimedia(2)

ipiFrLcnVcEmissionPriorityToNetwork		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.30
This attribute displays the network internal emission priotity to the network.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	normal(0), high(1), interrupting(2)

ipiFrLcnVcEmissionPriorityFromNetwork		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.31
This attribute displays the network internal emission priotity from the network.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	normal(0), high(1), interrupting(2)

ipiFrLcnVcDataPath		1.3.6.1.4.1.562.2.4.1.50.4.3.10.1.32
This attribute indicates the data path used by the connection. The data path is provisioned in Dna and DirectCall components. The displayed value of this attribute can be different from the provisioned value. If the connection is using dprsOnly data path, the string dprsOnly is displayed. (dynamic packet routing system) If the connection is using dprsMcsOnly data path, the string dprsMcsOnly is displayed. If the connection is using dprsMcsFirst data path, the string dprsMcsFirst is displayed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	AsciiString	Size(0..32)

ipiFrLcnVcIntdTable		1.3.6.1.4.1.562.2.4.1.50.4.3.11
This group defines display of interval data collected by Vc. Data in this group is variable and may depend on time when this display command is issued.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrLcnVcIntdEntry

ipiFrLcnVcIntdEntry		1.3.6.1.4.1.562.2.4.1.50.4.3.11.1
An entry in the ipiFrLcnVcIntdTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrLcnVcIntdEntry

ipiFrLcnVcCallReferenceNumber		1.3.6.1.4.1.562.2.4.1.50.4.3.11.1.1
This attribute displays the call reference number which is a unique number generated by the switch.The same Call Reference Number is stored in the interval data (accounting record) at both ends of the call. It can be used as one of the attributes in matching duplicate records generated at each end of the call.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Hex	0..16777215

ipiFrLcnVcElapsedTimeTillNow		1.3.6.1.4.1.562.2.4.1.50.4.3.11.1.2
This attribute displays the elapsed time representing the period of this interval data. It is elapsed time in 0.1 second increments since Vc started.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..16777215

ipiFrLcnVcSegmentsRx		1.3.6.1.4.1.562.2.4.1.50.4.3.11.1.3
This attribute displays the number of segments received at the time command was issued. This is the segment received count maintained by accounting at each end of the Vc. This counter is updated only when the packet cannot be successfully delivered out of the sink Vc and to the sink AP Conditions in which packets may be discarded by the sink Vc include: missing packets due to subnet discards, segmentation protocol violations due to subnet discard, duplicated and out-of-ranged packets and packets that arrive while Vc is in path recovery state.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..16777215

ipiFrLcnVcSegmentsSent		1.3.6.1.4.1.562.2.4.1.50.4.3.11.1.4
This attribute displays the number of segments sent at the time command was issued. This is the segment sent count maintained by accounting at the source Vc. Vc only counts packets that Vc thinks can be delivered successfully into the subnet. In reality, these packets may be dropped by trunking, for instance. This counter is not updated when splitting fails, when Vc is in a path recovery state, when packet forwarding fails to forward this packet and when subsequent packets have to be discarded as we want to minimize the chance of out-of-sequence and do not intentionally send out-of- sequenced packets into the subnet.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..16777215

ipiFrLcnVcStartTime		1.3.6.1.4.1.562.2.4.1.50.4.3.11.1.5
This attribute displays the start time of this interval period. If Vc spans 12 hour time or time of day change startTime reflects new time as recorded at 12 hour periods or time of day changes.
Status: mandatory	Access: read-only
OBJECT-TYPE
	EnterpriseDateAndTime	Size(0|19)

ipiFrLcnVcFrdTable		1.3.6.1.4.1.562.2.4.1.50.4.3.12
This group defines Frame Relay attributes collected by Frame Relay Vc. The purpose of Vc attributes is to aid end users and verification people to understand the Vc internal behavior. This is particularly useful when the network has experienced abnormality and we want to isolate problems and pinpoint trouble spots. Attributes are collected on a per Vc basis. Until a need is identified, statistics are not collected at a processor level. Each attribute is stored in a 32 bit field and is initialized to zero when a Vc enters into the data transfer state. When a PVC is disconnected and then connected again, the attributes will be reset. Attributes cannot be reset through other methods. Frame Relay Vc uses a best effort data packet delivery protocol and a different packet segmentation and combination methods from the General Vc. The Frame Relay Vc uses the same call setup and control mechanism (e.g. the support of non-flow control data packets) as in a General Vc. Most General Vc statistics and internal variables are used in a Frame Relay Vc and are displayed by software developers
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrLcnVcFrdEntry

ipiFrLcnVcFrdEntry		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1
An entry in the ipiFrLcnVcFrdTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrLcnVcFrdEntry

ipiFrLcnVcFrmCongestedToSubnet		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.2
This attribute displays the number of frames from link discarded due to lack of resources. It keeps track of the number of frames from link that have to be discarded. The discard reasons include insufficient memory for splitting the frame into smaller subnet packet size.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcCannotForwardToSubnet		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.3
This attribute displays the number of discarded packets that can not be forwarded into the subnet because of subnet congestion. Number of frames from link discarded due to failure in forwarding a packet from Vc into the subnet.- This attribute is increased when packet forwarding fails to forward a packet into the subnet. If a frame is split into multiple subnet packets and a partial packet has to be discarded, all subsequent partial packets that have not yet been delivered to the subnet will be discarded as well.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcNotDataXferToSubnet		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.4
This attribute records the number of frames from link discarded when the Vc tries to recover from internal path failure.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcOutOfRangeFrmFromSubnet		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.5
This attribute displays the number of frames from subnet discarded due to out of sequence range for arriving too late.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcCombErrorsFromSubnet		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.6
This attribute records the number of subnet packets discarded at the sink Vc due to the Vc segmentation and combination protocol error. Usually, this occurs when the subnet discards packets and thus this statistics can be used to guest the number of subnet packets that are not delivered to the Vc. It cannot be used as an actual measure because some subnet packets may have been delivered to Vc but have to be discarded because these are partial packets to a frame in which some other partial packets have not been properly delivered to Vc
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcDuplicatesFromSubnet		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.7
This attribute displays the number of subnet packets discarded due to duplication. Although packets are not retransmitted by the Frame Relay Vc, it is possible for the subnet to retransmit packets. When packets are out-of-sequenced and copies of the same packets arrive, then this attribute is increased.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcNotDataXferFromSubnet		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.8
This attribute displays the number of subnet packets discarded when data transfer is suspended in Vc recovery.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcFrmLossTimeouts		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.9
This attribute displays the number of lost frame timer expiries. When this count is excessive, the network is very congested and packets have been discarded in the subnet.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcOoSeqByteCntExceeded		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.10
This attribute displays the number times that the out of sequence byte threshold is exceeded. When the threshold is exceeded, this condition is treated as if the loss frame timer has expired and all frames queued at the sink Vc are delivered to the AP. We need to keep this count to examine if the threshold is engineered properly. This should be used in conjunction with the peak value of out-of- sequenced queue and the number of times the loss frame timer has expired. This count should be relatively small when compared with loss frame timer expiry count.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcPeakOoSeqPktCount		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.11
This attribute displays the frame relay peak packet count of the out of sequence queue. This attribute records the maximum queue length of the out-of-sequenced queue. The counter can be used to deduce the message buffer requirement on a Vc.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcPeakOoSeqFrmForwarded		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.12
This attribute displays the frame relay peak size of the sequence packet queue. The subnet may deliver packets out-of- sequenced. These packets are then queued in an out-of-sequenced queue, waiting for a packet with the expected sequence number to come. When that packet arrives, this attribute records the maximum number of packets that were out-of-sequenced, but now have become in-sequenced. The statistics is used to measure expected queue size due to normal subnet packet disorder (not due to subnet packet discard). Current implementation also uses this statistics to set a maximum size for the out-of-sequenced queue.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcSendSequenceNumber		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.13
This attribute displays the Vc internal packet's send sequence number. Note that a 'packet' in this context, may be either a user data packet, or an OAM frame.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcPktRetryTimeouts		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.15
This attribute displays the number of packets which have retransmission time-outs. When this count is excessive, the network is very congested and packets have been discarded in the subnet.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcPeakRetryQueueSize		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.16
This attribute displays the peak size of retransmission queue. This attribute is used as an indicator of the acknowledgment behavior across the subnet. Records the largest body of unacknowledged packets.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcSubnetRecoveries		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.17
This attribute displays the number of successful Vc recovery attempts.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..5000

ipiFrLcnVcOoSeqPktCntExceeded		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.19
This attribute displays the number times that the out of sequence packet threshold is exceeded. When the threshold is exceeded, this condition is treated as if the loss frame timer has expired and all frames queued at the sink Vc are delivered to the AP. We need to keep this count to examine if the threshold is engineered properly. This should be used in conjunction with the peak value of out-of- sequenced queue and the number of times the loss frame timer has expired. This count should be relatively small when compared with loss frame timer expiry count.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..255

ipiFrLcnVcPeakOoSeqByteCount		1.3.6.1.4.1.562.2.4.1.50.4.3.12.1.20
This attribute displays the frame relay peak byte count of the out of sequence queue. This attribute records the maximum queue length of the out-of-sequenced queue. The counter can be used to deduce the message buffer requirement on a Vc.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	0..50000

ipiFrLcnVcDmepTable		1.3.6.1.4.1.562.2.4.1.50.4.3.417
This attribute displays the data path used by the connection. Data path is provisioned in Dna and DirectCall components. If the connection is using dprsOnly data path, this attribute is empty. If the connection is using dprsMcsOnly or dprsMcsFirst data path, this attribute displays component name of the dprsMcsEndPoint.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrLcnVcDmepEntry

ipiFrLcnVcDmepEntry		1.3.6.1.4.1.562.2.4.1.50.4.3.417.1
An entry in the ipiFrLcnVcDmepTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrLcnVcDmepEntry

ipiFrLcnVcDmepValue		1.3.6.1.4.1.562.2.4.1.50.4.3.417.1.1
This variable represents both the value and the index for the ipiFrLcnVcDmepTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	RowPointer

ipiFrSr		1.3.6.1.4.1.562.2.4.1.50.5
OBJECT IDENTIFIER

ipiFrSrRowStatusTable		1.3.6.1.4.1.562.2.4.1.50.5.1
This entry controls the addition and deletion of ipiFrSr components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrSrRowStatusEntry

ipiFrSrRowStatusEntry		1.3.6.1.4.1.562.2.4.1.50.5.1.1
A single entry in the table represents a single ipiFrSr component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrSrRowStatusEntry

ipiFrSrRowStatus		1.3.6.1.4.1.562.2.4.1.50.5.1.1.1
This variable is used as the basis for SNMP naming of ipiFrSr components. These components can be added and deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

ipiFrSrComponentName		1.3.6.1.4.1.562.2.4.1.50.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

ipiFrSrStorageType		1.3.6.1.4.1.562.2.4.1.50.5.1.1.4
This variable represents the storage type value for the ipiFrSr tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

ipiFrSrIndex		1.3.6.1.4.1.562.2.4.1.50.5.1.1.10
This variable represents the index for the ipiFrSr tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpAddress

ipiFrSrProvTable		1.3.6.1.4.1.562.2.4.1.50.5.10
This group provides the provisionable parameters for setting up a static route.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrSrProvEntry

ipiFrSrProvEntry		1.3.6.1.4.1.562.2.4.1.50.5.10.1
An entry in the ipiFrSrProvTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrSrProvEntry

ipiFrSrGatewayIpAddress		1.3.6.1.4.1.562.2.4.1.50.5.10.1.1
The attribute specifies the IP Address of the next hop in this route to the destination IP Address. For this static route to be active, the value of this attribute must match the opRemoteIpAddress attribute of one of the Lcn components.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipiFrSrBGtyIpaTable		1.3.6.1.4.1.562.2.4.1.50.5.327
The attribute specifies an ordered list of alternative gateways to use for the route to the destination IP Address. This attribute is only supported for the default route. If the Lcn interface of the current gateway IP Address fails, then the backupGatewayIpAddresses, listed in this attribute, are searched, in order, for a gatewayIpAddress with an enabled Lcn. If found, the static route to this destination IP Address is updated to use the found gateway IP Address. Note that an Lcn interface can fail due to either the Vc through the Passport Network failing, or an Lmi indication that the far-end link is failed.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrSrBGtyIpaEntry

ipiFrSrBGtyIpaEntry		1.3.6.1.4.1.562.2.4.1.50.5.327.1
An entry in the ipiFrSrBGtyIpaTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrSrBGtyIpaEntry

ipiFrSrBGtyIpaIndex		1.3.6.1.4.1.562.2.4.1.50.5.327.1.1
This variable represents the index for the ipiFrSrBGtyIpaTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Integer32	1..23

ipiFrSrBGtyIpaValue		1.3.6.1.4.1.562.2.4.1.50.5.327.1.2
This variable represents an individual value for the ipiFrSrBGtyIpaTable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipiFrSrBGtyIpaRowStatus		1.3.6.1.4.1.562.2.4.1.50.5.327.1.3
This variable is used to control the addition and deletion of individual values of the ipiFrSrBGtyIpaTable.
Status: mandatory	Access: write-only
OBJECT-TYPE
	RowStatus

ipiFrR		1.3.6.1.4.1.562.2.4.1.50.6
OBJECT IDENTIFIER

ipiFrRRowStatusTable		1.3.6.1.4.1.562.2.4.1.50.6.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of ipiFrR components.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrRRowStatusEntry

ipiFrRRowStatusEntry		1.3.6.1.4.1.562.2.4.1.50.6.1.1
A single entry in the table represents a single ipiFrR component.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrRRowStatusEntry

ipiFrRRowStatus		1.3.6.1.4.1.562.2.4.1.50.6.1.1.1
This variable is used as the basis for SNMP naming of ipiFrR components. These components cannot be added nor deleted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	RowStatus

ipiFrRComponentName		1.3.6.1.4.1.562.2.4.1.50.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

ipiFrRStorageType		1.3.6.1.4.1.562.2.4.1.50.6.1.1.4
This variable represents the storage type value for the ipiFrR tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	StorageType

ipiFrRIndex		1.3.6.1.4.1.562.2.4.1.50.6.1.1.10
This variable represents the index for the ipiFrR tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpAddress

ipiFrROperTable		1.3.6.1.4.1.562.2.4.1.50.6.10
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains operational status of the static route
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpiFrROperEntry

ipiFrROperEntry		1.3.6.1.4.1.562.2.4.1.50.6.10.1
An entry in the ipiFrROperTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpiFrROperEntry

ipiFrRGtyIpAddr		1.3.6.1.4.1.562.2.4.1.50.6.10.1.1
The attribute specifies the IP Address of the next hop in this route to the destination IP Address.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IpAddress

ipiFrRLcnIf		1.3.6.1.4.1.562.2.4.1.50.6.10.1.3
This attribute specifies the Lcn interface used by this IP route.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Unsigned32	16..39

ipiFrRType		1.3.6.1.4.1.562.2.4.1.50.6.10.1.4
This attribute indicates whether a route is going to a host or a subnet or a network.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	host(1), subnet(2), network(3)

ipiFrGroup		1.3.6.1.4.1.562.2.4.2.35.1
OBJECT IDENTIFIER

ipiFrGroupBE		1.3.6.1.4.1.562.2.4.2.35.1.5
OBJECT IDENTIFIER

ipiFrGroupBE01		1.3.6.1.4.1.562.2.4.2.35.1.5.2
OBJECT IDENTIFIER

ipiFrGroupBE01A		1.3.6.1.4.1.562.2.4.2.35.1.5.2.2
OBJECT IDENTIFIER

ipiFrCapabilities		1.3.6.1.4.1.562.2.4.2.35.3
OBJECT IDENTIFIER

ipiFrCapabilitiesBE		1.3.6.1.4.1.562.2.4.2.35.3.5
OBJECT IDENTIFIER

ipiFrCapabilitiesBE01		1.3.6.1.4.1.562.2.4.2.35.3.5.2
OBJECT IDENTIFIER

ipiFrCapabilitiesBE01A		1.3.6.1.4.1.562.2.4.2.35.3.5.2.2
OBJECT IDENTIFIER