Nortel-MsCarrier-MscPassport-CircuitEmulationServiceMIB

File: Nortel-MsCarrier-MscPassport-CircuitEmulationServiceMIB.mib (145757 bytes)

Imported modules

RFC-1212 Nortel-MsCarrier-MscPassport-UsefulDefinitionsMIB Nortel-MsCarrier-MscPassport-StandardTextualConventionsMIB
Nortel-MsCarrier-MscPassport-TextualConventionsMIB

Imported symbols

OBJECT-TYPE mscPassportMIBs mscComponents
Counter32 RowPointer DisplayString
StorageType RowStatus Gauge32
Integer32 Unsigned32 AsciiString
Hex NonReplicated EnterpriseDateAndTime
PassportCounter64 Link IntegerSequence
FixedPoint2

Defined Types

MscAal1CesRowStatusEntry  
SEQUENCE    
  mscAal1CesRowStatus RowStatus
  mscAal1CesComponentName DisplayString
  mscAal1CesStorageType StorageType
  mscAal1CesIndex Integer32

MscAal1CesCidDataEntry  
SEQUENCE    
  mscAal1CesCustomerIdentifier Unsigned32

MscAal1CesProvEntry  
SEQUENCE    
  mscAal1CesServiceType INTEGER
  mscAal1CesBufferSize Unsigned32
  mscAal1CesCellLossIntegrationPeriod Unsigned32
  mscAal1CesInterfaceName Link
  mscAal1CesPartialFill Unsigned32
  mscAal1CesIdleSuppression INTEGER
  mscAal1CesIdlePattern Hex
  mscAal1CesCellLossRecoveryPeriod Unsigned32
  mscAal1CesDummyDataByte Hex
  mscAal1CesMaximumBufferDelay FixedPoint2
  mscAal1CesDp2CellDelayVariationTolerance FixedPoint2

MscAal1CesStateEntry  
SEQUENCE    
  mscAal1CesAdminState INTEGER
  mscAal1CesOperationalState INTEGER
  mscAal1CesUsageState INTEGER
  mscAal1CesAvailabilityStatus OCTET STRING
  mscAal1CesProceduralStatus OCTET STRING
  mscAal1CesControlStatus OCTET STRING
  mscAal1CesAlarmStatus OCTET STRING
  mscAal1CesStandbyStatus INTEGER
  mscAal1CesUnknownStatus INTEGER

MscAal1CesOperEntry  
SEQUENCE    
  mscAal1CesCellLossStatus INTEGER
  mscAal1CesAal1LayerLossStatus INTEGER
  mscAal1CesConnectionStatus INTEGER

MscAal1CesStatsEntry  
SEQUENCE    
  mscAal1CesCellsTransmitted PassportCounter64
  mscAal1CesCellsReceived PassportCounter64
  mscAal1CesLostCells Counter32
  mscAal1CesBufferUnderflows Counter32
  mscAal1CesBufferOverflows Counter32
  mscAal1CesReassembledCells PassportCounter64
  mscAal1CesHeaderErrors Counter32
  mscAal1CesPointerReframes Counter32
  mscAal1CesPointerParityErrors Counter32
  mscAal1CesAal1SequenceErrors Counter32
  mscAal1CesMisinsertedCells Counter32

MscAal1CesNapRowStatusEntry  
SEQUENCE    
  mscAal1CesNapRowStatus RowStatus
  mscAal1CesNapComponentName DisplayString
  mscAal1CesNapStorageType StorageType
  mscAal1CesNapIndex NonReplicated

MscAal1CesNapProvEntry  
SEQUENCE    
  mscAal1CesNapAtmConnection Link

MscAal1CesAepRowStatusEntry  
SEQUENCE    
  mscAal1CesAepRowStatus RowStatus
  mscAal1CesAepComponentName DisplayString
  mscAal1CesAepStorageType StorageType
  mscAal1CesAepIndex NonReplicated

MscAal1CesAepProvEndPointAddrEntry  
SEQUENCE    
  mscAal1CesAepExpectedRemoteAddress AsciiString
  mscAal1CesAepLocalAddress AsciiString

MscAal1CesAepProvEntry  
SEQUENCE    
  mscAal1CesAepAddressToCall AsciiString
  mscAal1CesAepRoutingOption INTEGER
  mscAal1CesAepProfile Link
  mscAal1CesAepFirstRetryInterval Unsigned32
  mscAal1CesAepRetryLimit Unsigned32
  mscAal1CesAepActiveEndPointType INTEGER
  mscAal1CesAepCalledVpiVci IntegerSequence

MscAal1CesAepEpOperEntry  
SEQUENCE    
  mscAal1CesAepRemoteAddress AsciiString
  mscAal1CesAepLastTearDownCause Unsigned32
  mscAal1CesAepLastTearDownDiagnostic AsciiString

MscAal1CesAepOutEntry  
SEQUENCE    
  mscAal1CesAepSvcStatus INTEGER
  mscAal1CesAepLastSetupFailureCause Unsigned32
  mscAal1CesAepLastSetupFailureDiagnostic AsciiString
  mscAal1CesAepRetryTimeRemaining Counter32
  mscAal1CesAepRetryFailures Counter32

MscAal1CesPepRowStatusEntry  
SEQUENCE    
  mscAal1CesPepRowStatus RowStatus
  mscAal1CesPepComponentName DisplayString
  mscAal1CesPepStorageType StorageType
  mscAal1CesPepIndex NonReplicated

MscAal1CesPepProvEndPointAddrEntry  
SEQUENCE    
  mscAal1CesPepExpectedRemoteAddress AsciiString
  mscAal1CesPepLocalAddress AsciiString

MscAal1CesPepEpOperEntry  
SEQUENCE    
  mscAal1CesPepRemoteAddress AsciiString
  mscAal1CesPepLastTearDownCause Unsigned32
  mscAal1CesPepLastTearDownDiagnostic AsciiString

MscAal1CesPepPassiveOperEntry  
SEQUENCE    
  mscAal1CesPepSvcStatus INTEGER

MscAal1CesLCoRowStatusEntry  
SEQUENCE    
  mscAal1CesLCoRowStatus RowStatus
  mscAal1CesLCoComponentName DisplayString
  mscAal1CesLCoStorageType StorageType
  mscAal1CesLCoIndex NonReplicated

MscAal1CesLCoPathDataEntry  
SEQUENCE    
  mscAal1CesLCoState INTEGER
  mscAal1CesLCoOverrideRemoteName AsciiString
  mscAal1CesLCoEnd INTEGER
  mscAal1CesLCoCostMetric Unsigned32
  mscAal1CesLCoDelayMetric Unsigned32
  mscAal1CesLCoRoundTripDelay Unsigned32
  mscAal1CesLCoSetupPriority Unsigned32
  mscAal1CesLCoHoldingPriority Unsigned32
  mscAal1CesLCoRequiredTxBandwidth Gauge32
  mscAal1CesLCoRequiredRxBandwidth Gauge32
  mscAal1CesLCoRequiredTrafficType INTEGER
  mscAal1CesLCoPermittedTrunkTypes OCTET STRING
  mscAal1CesLCoRequiredSecurity Unsigned32
  mscAal1CesLCoRequiredCustomerParameter Unsigned32
  mscAal1CesLCoEmissionPriority Unsigned32
  mscAal1CesLCoDiscardPriority Unsigned32
  mscAal1CesLCoPathType INTEGER
  mscAal1CesLCoRetryCount Unsigned32
  mscAal1CesLCoPathFailureCount Unsigned32
  mscAal1CesLCoReasonForNoRoute INTEGER
  mscAal1CesLCoLastTearDownReason INTEGER
  mscAal1CesLCoPathFailureAction INTEGER
  mscAal1CesLCoBumpPreference INTEGER
  mscAal1CesLCoOptimization INTEGER
  mscAal1CesLCoPathUpDateTime EnterpriseDateAndTime

MscAal1CesLCoStatsEntry  
SEQUENCE    
  mscAal1CesLCoPktsToNetwork PassportCounter64
  mscAal1CesLCoBytesToNetwork PassportCounter64
  mscAal1CesLCoPktsFromNetwork PassportCounter64
  mscAal1CesLCoBytesFromNetwork PassportCounter64

MscAal1CesLCoPathEntry  
SEQUENCE    
  mscAal1CesLCoPathValue AsciiString

MscAal1CesAtmConRowStatusEntry  
SEQUENCE    
  mscAal1CesAtmConRowStatus RowStatus
  mscAal1CesAtmConComponentName DisplayString
  mscAal1CesAtmConStorageType StorageType
  mscAal1CesAtmConIndex NonReplicated

MscAal1CesAtmConOperEntry  
SEQUENCE    
  mscAal1CesAtmConNextHop RowPointer

MscMmTxRowStatusEntry  
SEQUENCE    
  mscMmTxRowStatus RowStatus
  mscMmTxComponentName DisplayString
  mscMmTxStorageType StorageType
  mscMmTxIndex Integer32

MscMmTxCidDataEntry  
SEQUENCE    
  mscMmTxCustomerIdentifier Unsigned32

MscMmTxProvEntry  
SEQUENCE    
  mscMmTxLinkToLogicalProcessor Link
  mscMmTxMonitoredDirection INTEGER
  mscMmTxServiceType INTEGER
  mscMmTxPartialFill Unsigned32
  mscMmTxIdleSuppression INTEGER

MscMmTxStateEntry  
SEQUENCE    
  mscMmTxAdminState INTEGER
  mscMmTxOperationalState INTEGER
  mscMmTxUsageState INTEGER
  mscMmTxAvailabilityStatus OCTET STRING
  mscMmTxProceduralStatus OCTET STRING
  mscMmTxControlStatus OCTET STRING
  mscMmTxAlarmStatus OCTET STRING
  mscMmTxStandbyStatus INTEGER
  mscMmTxUnknownStatus INTEGER

MscMmTxOperEntry  
SEQUENCE    
  mscMmTxConnectionStatus INTEGER
  mscMmTxChanToMonitor RowPointer

MscMmTxNapRowStatusEntry  
SEQUENCE    
  mscMmTxNapRowStatus RowStatus
  mscMmTxNapComponentName DisplayString
  mscMmTxNapStorageType StorageType
  mscMmTxNapIndex NonReplicated

MscMmTxNapProvEntry  
SEQUENCE    
  mscMmTxNapAtmConnection Link

MscMmTxAtmConRowStatusEntry  
SEQUENCE    
  mscMmTxAtmConRowStatus RowStatus
  mscMmTxAtmConComponentName DisplayString
  mscMmTxAtmConStorageType StorageType
  mscMmTxAtmConIndex NonReplicated

MscMmTxAtmConOperEntry  
SEQUENCE    
  mscMmTxAtmConNextHop RowPointer

Defined Values

circuitEmulationServiceMIB 1.3.6.1.4.1.562.36.2.2.55
OBJECT IDENTIFIER    

mscAal1Ces 1.3.6.1.4.1.562.36.2.1.119
OBJECT IDENTIFIER    

mscAal1CesRowStatusTable 1.3.6.1.4.1.562.36.2.1.119.1
This entry controls the addition and deletion of mscAal1Ces components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesRowStatusEntry

mscAal1CesRowStatusEntry 1.3.6.1.4.1.562.36.2.1.119.1.1
A single entry in the table represents a single mscAal1Ces component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesRowStatusEntry  

mscAal1CesRowStatus 1.3.6.1.4.1.562.36.2.1.119.1.1.1
This variable is used as the basis for SNMP naming of mscAal1Ces components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mscAal1CesComponentName 1.3.6.1.4.1.562.36.2.1.119.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscAal1CesStorageType 1.3.6.1.4.1.562.36.2.1.119.1.1.4
This variable represents the storage type value for the mscAal1Ces tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscAal1CesIndex 1.3.6.1.4.1.562.36.2.1.119.1.1.10
This variable represents the index for the mscAal1Ces tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16383  

mscAal1CesCidDataTable 1.3.6.1.4.1.562.36.2.1.119.10
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesCidDataEntry

mscAal1CesCidDataEntry 1.3.6.1.4.1.562.36.2.1.119.10.1
An entry in the mscAal1CesCidDataTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesCidDataEntry  

mscAal1CesCustomerIdentifier 1.3.6.1.4.1.562.36.2.1.119.10.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

mscAal1CesProvTable 1.3.6.1.4.1.562.36.2.1.119.11
This group contains basic provisioning data for the AAL1 Circuit Emulation Service.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesProvEntry

mscAal1CesProvEntry 1.3.6.1.4.1.562.36.2.1.119.11.1
An entry in the mscAal1CesProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesProvEntry  

mscAal1CesServiceType 1.3.6.1.4.1.562.36.2.1.119.11.1.1
This attribute specifies the service type for the CES. In an unstructured service, the entire data stream at the service interface (including any framing bits which may be present) is passed across the network transparently. The unstructured service uses the Unstructured Data Transfer (UDT) mode of AAL1. In a structured service, an Nx64kbit/s fraction of the data stream at the service interface is passed across the network. Two modes of structured service are supported: basicStructured and casStructured. In a casStructured service, the Channel Associated Signalling (CAS) bits are carried in a separate data structure from the Nx64 payload; in a basicStructured service they are not. The structured service uses the Structured Data Transfer (SDT) mode as defined in ITU-T Recommendation I.363.1. The serviceType attributes at both ends of a connection must be the same.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER unstructured(0), basicStructured(1), casStructured(2)  

mscAal1CesBufferSize 1.3.6.1.4.1.562.36.2.1.119.11.1.2
On 4pDS1Aal1 and 4pE1Aal1 cards, this attribute specifies the size of the AAL1 receive segment reassembly buffer in bytes. On initialization the buffer is filled to a level determined by cellDelayVariationTolerance. Thereafter the buffer is emptied as TDM frames are transmitted, and is filled as ATM cells are received. If the buffer overflows, sufficient data is discarded to bring the level down to that set after initialization. The cause of a buffer overflow may be one or a combination of any of the following: cell- arrival-jitter, initialization with delayed ATM cells, or TDM clock difference or wander. On 4pDS1Aal1 and 4pE1Aal1 cards, if this attribute is autoConfigure, the buffer size applied is equivalent to two times cellDelayVariationTolerance. A provisioned numeric value of bufferSize must be higher than the equivalent cellDelayVariationTolerance, plus an allowance of one ATM Cell for the quantization of data in cells, and an allowance, if applicable, for the ATM overheads of structured CES. On MSA cards this attribute's value must be autoConfigure, to acknowledge that maximumBufferDelay is provisioned instead of this attribute. Setting this attribute too low allows traffic with normal CDV to cause unnecessary loss of data on the service interface. Setting this attribute too high permits the buffer to introduce an unnecessarily high propagation delay. VALUES ( 0 = autoConfigure )
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 94..15651  

mscAal1CesCellLossIntegrationPeriod 1.3.6.1.4.1.562.36.2.1.119.11.1.4
This attribute specifies the cell loss integration period. This period defines the interval of time (in milliseconds) for which a loss of cells condition must persist before a buffer underflow alarm is raised. A loss of cells condition occurs when the flow of cells to the AAL1 reassembly buffer stops, causing a buffer underflow or starvation condition. The operational attribute cellLossStatus will be set to loss when the buffer underflow alarm is raised, and noLoss when it is cleared.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..60000  

mscAal1CesInterfaceName 1.3.6.1.4.1.562.36.2.1.119.11.1.5
This attribute identifies the instance of Chan to which an instance of Aal1Ces is linked.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

mscAal1CesPartialFill 1.3.6.1.4.1.562.36.2.1.119.11.1.6
A significant source of delay in a structured service is the amount of time it takes to collect enough data to fill a cell. This period of time can be reduced by sending cells that are only partially filled with data (idlePattern octets are added to the ATM payload beyond the partial fill level). This attribute specifies the number of payload octets to fill with data. It is applicable to structured services only, and must be set to 47 for unstructured services. On a given AAL1 Function Processor, the maximum cell rate that can be sustained is dependent upon the combined bandwidths of the provisioned services, and (for structured services) the levels of partialFill. The smaller the partialFill level, the greater the cell rate and hence the fewer the services that can be sustained at that fill level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 8..47  

mscAal1CesIdleSuppression 1.3.6.1.4.1.562.36.2.1.119.11.1.7
This attribute controls the suppression of idle cells. An idle cell is one in which the bytes of the ATM payload (up to the partialFill level) match the idlePattern. If idleSuppression is off, idle cells are not suppressed. If idleSuppression is on, at least 75% of cells are suppressed under idle conditions. The strategy is as follows: the first idle cell after a sequence of non- idle cells is always sent; those that follow are suppressed. Note, however, that at least one cell in eight is always sent (to allow the receive end to regenerate the suppressed cells) and more often than not, two cells are sent (the cell containing the AAL1 pointer, which will almost always fail to match, and the one after that).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscAal1CesIdlePattern 1.3.6.1.4.1.562.36.2.1.119.11.1.8
This attribute specifies the pattern which the bytes of an ATM payload, up to the partialFill level, must match in order for the cell to be classified as idle. Payload bytes beyond the partialFill level are not checked. The suppression of idle cells is controlled by the attribute idleSuppression. If idleSuppression is on, at least 75% of cells are suppressed under idle conditions.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Hex 0..255  

mscAal1CesCellLossRecoveryPeriod 1.3.6.1.4.1.562.36.2.1.119.11.1.9
This attribute specifies the cell loss recovery period. This period defines the interval of time (in seconds) for which a loss of cells condition must desist before the buffer underflow alarm is cleared. The operational attribute cellLossStatus will be set to noLoss when the buffer underflow alarm is cleared.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..60  

mscAal1CesDummyDataByte 1.3.6.1.4.1.562.36.2.1.119.11.1.10
This attribute specifies the pattern which is played out onto the service interface to maintain bit integrity when data is unavailable from the ATM network. For an unstructured service (serviceType is set to unstructured), dummyDataByte must be set to FF.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Hex 0..255  

mscAal1CesMaximumBufferDelay 1.3.6.1.4.1.562.36.2.1.119.11.1.11
This attribute specifies the maximum delay that a Cell Delay Variation buffer is permitted to add to the egress stream. The delay in the buffer is modified in response to variation in the egress cell stream. At the point that the delay would be modified in excess of the maximum, sufficient data is discarded that the delay returns to cellDelayVariationTolerance. Setting this attribute too low allows traffic with normal CDV to cause unnecessary loss of data on the service interface. Setting this attribute too high permits the buffer to introduce an unnecessarily high propagation delay. If this attribute is autoConfigure, the maximum delay tolerated in the buffer is two times cellDelayVariationTolerance. On MSA cards, 'best-effort' applies on a channel with high cellDelayVariationTolerance and low ATM bandwidth. The value applied is the same as the range limit on provisioned maximumBufferDelay on that channel. On MSA cards this attribute's value is rounded up to the nearest multiple of 0.125ms when applied to the buffer. The range is nominally 0.12..63.62ms, but the upper limit may be reduced by up to 6ms one a channel with high cellDelayVariationTolerance and low ATM bandwidth. On 4pDS1Aal1 and 4pE1Aal1 cards this attribute's value is rounded up to the nearest multiple of 1ms when applied to the buffer. The upper limit is roughly inverse- proportional to the ATM bandwidth of the channel. VALUES ( 0 = autoConfigure )
Status: mandatory Access: read-write
OBJECT-TYPE    
  FixedPoint2 0 | 1..65500  

mscAal1CesDp2CellDelayVariationTolerance 1.3.6.1.4.1.562.36.2.1.119.11.1.12
This attribute specifies the maximum time that a cell may arrive late, compared to a nominal time established at buffer initialization, without producing errors on the service interface. The nominal time of a cell's arrival is predicted according to the time interval required to transmit a cell's worth of data on the service interface. This attribute's value is the delay that the Cell Delay Variation Tolerance buffer adds to the egress stream immediately after the buffer initializes. The buffer absorbs variation in the arrival time of cells from the network, so that a steady stream of data appears on the service interface. If the buffer underflows, due to a late cell, fill- in data is output on the service interface while the buffer re- initializes. When the buffer has re-initialized, normal data is output on the service interface and the delay in the buffer is restored to the value of this attribute. This attribute must have a value lower than a numeric value of maximumBufferDelay. The relationship between this attribute and bufferSize is described under that attribute. Setting this attribute too low allows traffic with normal CDV to cause unnecessary loss of data on the service interface. Setting this attribute too high imposes an unnecessarily high propagation delay on the egress stream. On MSA cards this attribute's provisionable range is 0.01..32ms and the value applied is rounded up to the nearest multiple of 0.125ms. On 4pDS1Aal1 and 4pE1Aal1 cards, this attribute's provisionable range is strongly dependent on the bandwidth of the channel, and the value applied is rounded up to the nearest whole number of milliseconds, then rounded down to the equivalent number of cells.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FixedPoint2 1..65500  

mscAal1CesStateTable 1.3.6.1.4.1.562.36.2.1.119.12
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesStateEntry

mscAal1CesStateEntry 1.3.6.1.4.1.562.36.2.1.119.12.1
An entry in the mscAal1CesStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesStateEntry  

mscAal1CesAdminState 1.3.6.1.4.1.562.36.2.1.119.12.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscAal1CesOperationalState 1.3.6.1.4.1.562.36.2.1.119.12.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscAal1CesUsageState 1.3.6.1.4.1.562.36.2.1.119.12.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscAal1CesAvailabilityStatus 1.3.6.1.4.1.562.36.2.1.119.12.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

mscAal1CesProceduralStatus 1.3.6.1.4.1.562.36.2.1.119.12.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mscAal1CesControlStatus 1.3.6.1.4.1.562.36.2.1.119.12.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mscAal1CesAlarmStatus 1.3.6.1.4.1.562.36.2.1.119.12.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mscAal1CesStandbyStatus 1.3.6.1.4.1.562.36.2.1.119.12.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER hotStandby(0), coldStandby(1), providingService(2), notSet(15)  

mscAal1CesUnknownStatus 1.3.6.1.4.1.562.36.2.1.119.12.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

mscAal1CesOperTable 1.3.6.1.4.1.562.36.2.1.119.13
This group contains status information about the AAL1 Circuit Emulation Service.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesOperEntry

mscAal1CesOperEntry 1.3.6.1.4.1.562.36.2.1.119.13.1
An entry in the mscAal1CesOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesOperEntry  

mscAal1CesCellLossStatus 1.3.6.1.4.1.562.36.2.1.119.13.1.1
This attribute is set to loss when a buffer underflow alarm is raised (see cellLossIntegrationPeriod), and noLoss when it is clear.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noLoss(0), loss(1)  

mscAal1CesAal1LayerLossStatus 1.3.6.1.4.1.562.36.2.1.119.13.1.2
This attribute is set to loss when an AAL1 layer alarm is raised, and noLoss when it is clear.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noLoss(0), loss(1)  

mscAal1CesConnectionStatus 1.3.6.1.4.1.562.36.2.1.119.13.1.3
This attribute indicates whether a service is non-operational because of a problem with the service interface side of the service (in which case, it is set to channelNotReady) or because of a problem with the ATM side of the service (in which case, it is set to atmNotConfigured or atmNotReady). When this attribute is set to channelNotReady, it is an indication that the corresponding Chan component (as defined by the attribute interfaceName) or the Chan component's parent port component (Lp/n Ds1/m or Lp/n E1/m) is locked. When this attribute is set to atmNotConfigured, it is an indication that no sub-component has been provisioned, and thus no ATM connection has been configured for the service. When this attribute is set to atmNotReady, it is an indication that the ATM connection with which the service is associated (as defined by a sub-component) has been lost or that it is currently unable to carry CES data. This attribute is set to connected when a service is operational (that is, the OSI attribute operationalState is enabled.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER connected(0), channelNotReady(1), atmNotReady(2), atmNotConfigured(3)  

mscAal1CesStatsTable 1.3.6.1.4.1.562.36.2.1.119.14
This group contains statistical data for an AAL1 Circuit Emulation Service.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesStatsEntry

mscAal1CesStatsEntry 1.3.6.1.4.1.562.36.2.1.119.14.1
An entry in the mscAal1CesStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesStatsEntry  

mscAal1CesCellsTransmitted 1.3.6.1.4.1.562.36.2.1.119.14.1.1
This attribute counts the total number of cells transmitted to the backplane (ingress direction). This includes cells containing CBR data, trunk conditioning cells (structured services), and unframed AIS cells (unstructured services). The counter wraps when the maximum value is exceeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

mscAal1CesCellsReceived 1.3.6.1.4.1.562.36.2.1.119.14.1.2
This attribute counts the total number of cells received from the backplane (egress direction). This includes CBR user data cells, cells with AAL1 header errors (correctable and non-correctable) and cells with AAL1 sequencing errors. The counter wraps when the maximum value is exceeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

mscAal1CesLostCells 1.3.6.1.4.1.562.36.2.1.119.14.1.3
This attribute counts the number of cells declared as never received by the AAL1 protocol layer. The counter wraps when the maximum value is exceeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscAal1CesBufferUnderflows 1.3.6.1.4.1.562.36.2.1.119.14.1.4
This attribute counts the number of times the AAL1 reassembly buffer underflows. In the case of a continuous buffer starvation, a single buffer underflow event will be counted. The counter wraps when the maximum value is exceeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscAal1CesBufferOverflows 1.3.6.1.4.1.562.36.2.1.119.14.1.5
This attribute counts the number of times the AAL1 reassembly buffer overflows. Buffer overflows occur when AAL1 cells arrive at a rate above that which is expected. Occurrences of this condition may be reduced by increasing the value of the attribute bufferSize or maximumBufferDelay. The buffer overflow counter wraps when the maximum value is exceeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscAal1CesReassembledCells 1.3.6.1.4.1.562.36.2.1.119.14.1.6
This attribute counts the number of received cells whose payload has been played out to the service interface. The counter wraps when the maximum value is exceeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

mscAal1CesHeaderErrors 1.3.6.1.4.1.562.36.2.1.119.14.1.7
This attribute counts the number of cells received with AAL1 header errors. The counter wraps when the maximum value is exceeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscAal1CesPointerReframes 1.3.6.1.4.1.562.36.2.1.119.14.1.8
This attribute counts the number of times that the AAL1 reassembly unit found an SDT pointer where it was not expected to be, and as a result had to reacquire it. Errors of this kind can occur because of problems at the far end. This attribute is meaningful for structured services only, and will be 0 for unstructured services. This counter wraps when the maximum value is exceeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscAal1CesPointerParityErrors 1.3.6.1.4.1.562.36.2.1.119.14.1.9
This attribute counts the number of times that the AAL1 reassembly unit detects a parity check failure at the point where an SDT pointer is expected. Errors of this kind can occur because of problems at the far end. This attribute is meaningful for structured services only, and will be 0 for unstructured services. This counter wraps when the maximum value is exceeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscAal1CesAal1SequenceErrors 1.3.6.1.4.1.562.36.2.1.119.14.1.10
This attribute counts the number of times that the sequence number of an incoming AAL1 Type 1 SAR-PDU gets out of synchronisation, as defined by ITU-T Recommendation I.363.1. This counter wraps when the maximum value is exceeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscAal1CesMisinsertedCells 1.3.6.1.4.1.562.36.2.1.119.14.1.11
This attribute counts the number of AAL1 sequence violations which the AAL convergence sublayer interprets as misinserted cells, as defined by ITU-T I.363.1. This counter wraps when the maximum value is exceeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscAal1CesNap 1.3.6.1.4.1.562.36.2.1.119.2
OBJECT IDENTIFIER    

mscAal1CesNapRowStatusTable 1.3.6.1.4.1.562.36.2.1.119.2.1
This entry controls the addition and deletion of mscAal1CesNap components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesNapRowStatusEntry

mscAal1CesNapRowStatusEntry 1.3.6.1.4.1.562.36.2.1.119.2.1.1
A single entry in the table represents a single mscAal1CesNap component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesNapRowStatusEntry  

mscAal1CesNapRowStatus 1.3.6.1.4.1.562.36.2.1.119.2.1.1.1
This variable is used as the basis for SNMP naming of mscAal1CesNap components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mscAal1CesNapComponentName 1.3.6.1.4.1.562.36.2.1.119.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscAal1CesNapStorageType 1.3.6.1.4.1.562.36.2.1.119.2.1.1.4
This variable represents the storage type value for the mscAal1CesNap tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscAal1CesNapIndex 1.3.6.1.4.1.562.36.2.1.119.2.1.1.10
This variable represents the index for the mscAal1CesNap tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mscAal1CesNapProvTable 1.3.6.1.4.1.562.36.2.1.119.2.10
This group contains the provisioning data for the NailedUpAdaptationPoint component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesNapProvEntry

mscAal1CesNapProvEntry 1.3.6.1.4.1.562.36.2.1.119.2.10.1
An entry in the mscAal1CesNapProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesNapProvEntry  

mscAal1CesNapAtmConnection 1.3.6.1.4.1.562.36.2.1.119.2.10.1.1
This attribute specifies the identity of the component to which the NailedUpAdaptationPoint is linked. This is an AtmIf Vcc NailedUpEndPoint or an AtmIf Vpt Vcc NailedUpEndPoint (the AAL1 cells are transported off the switch over an ATM UNI, where they are routed to the appropriate AAL1 entity at the other end by the ATM bearer service).
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

mscAal1CesAep 1.3.6.1.4.1.562.36.2.1.119.3
OBJECT IDENTIFIER    

mscAal1CesAepRowStatusTable 1.3.6.1.4.1.562.36.2.1.119.3.1
This entry controls the addition and deletion of mscAal1CesAep components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesAepRowStatusEntry

mscAal1CesAepRowStatusEntry 1.3.6.1.4.1.562.36.2.1.119.3.1.1
A single entry in the table represents a single mscAal1CesAep component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesAepRowStatusEntry  

mscAal1CesAepRowStatus 1.3.6.1.4.1.562.36.2.1.119.3.1.1.1
This variable is used as the basis for SNMP naming of mscAal1CesAep components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mscAal1CesAepComponentName 1.3.6.1.4.1.562.36.2.1.119.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscAal1CesAepStorageType 1.3.6.1.4.1.562.36.2.1.119.3.1.1.4
This variable represents the storage type value for the mscAal1CesAep tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscAal1CesAepIndex 1.3.6.1.4.1.562.36.2.1.119.3.1.1.10
This variable represents the index for the mscAal1CesAep tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mscAal1CesAepProvEndPointAddrTable 1.3.6.1.4.1.562.36.2.1.119.3.10
This group contains NSAP address provisioning data for components using switched virtual circuits.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesAepProvEndPointAddrEntry

mscAal1CesAepProvEndPointAddrEntry 1.3.6.1.4.1.562.36.2.1.119.3.10.1
An entry in the mscAal1CesAepProvEndPointAddrTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesAepProvEndPointAddrEntry  

mscAal1CesAepExpectedRemoteAddress 1.3.6.1.4.1.562.36.2.1.119.3.10.1.1
This attribute specifies the expected remote address prefix for an incoming connection setup request. If expectedRemoteAddress is not empty, only matching connections will be considered for acceptance. If expectedRemoteAddress is 40 characters long, the remote address must match exactly to be accepted. If expectedRemoteAddress is less than 40 characters long, the remote address must begin with expectedRemoteAddress to be accepted. If expectedRemoteAddress is empty, the component will process connection requests from any remote address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(0..40)  

mscAal1CesAepLocalAddress 1.3.6.1.4.1.562.36.2.1.119.3.10.1.2
This attribute specifies the local NSAP address. If the switch prefix (the nodePrefix attribute of the ModuleData component) has been provisioned, a default value for localAddress based on nodePrefix will be provided. If ModuleData nodePrefix has not been provisioned and one or more alternate switch prefixes (the alternatePorsPrefixes attribute of the ModuleData component) have been provisioned, a default value for localAddress based on the first provisioned alternatePorsPrefix value will be provided. If no switch prefixes have been provisioned, localAddress will default to an empty string. To obtain a valid default localAddress in this case, either or both of the ModuleData nodePrefix and ModuleData alternatePorsPrefixes attributes must be provisioned, and this end point component must then be deleted and re-added.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(40)  

mscAal1CesAepProvTable 1.3.6.1.4.1.562.36.2.1.119.3.11
This group contains the provisioning data specific to the ActiveEndPoint component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesAepProvEntry

mscAal1CesAepProvEntry 1.3.6.1.4.1.562.36.2.1.119.3.11.1
An entry in the mscAal1CesAepProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesAepProvEntry  

mscAal1CesAepAddressToCall 1.3.6.1.4.1.562.36.2.1.119.3.11.1.1
This attribute specifies the remote NSAP address which this ActiveEndPoint will call.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(40)  

mscAal1CesAepRoutingOption 1.3.6.1.4.1.562.36.2.1.119.3.11.1.2
This attribute specifies the type of routing to use for establishing the connection: AAL1 cards accept only porsOnly. Multi-Service Access cards accept all four options. porsOnly means that only the Path Oriented Routing System may be used in establishing a connection. atmOnly means that only the native ATM Routing may be used in establishing a connection. porsFirst means that the switch tries to establish a connection using the Path Oriented Routing System first, and, if the connection cannot be established, it tries native ATM Routing instead. atmFirst means that the switch tries to establish a connection using native ATM Routing first, and, if the connection cannot be established, it tries the Path Oriented Routing System instead.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER porsOnly(0), atmOnly(1), porsFirst(2), atmFirst(3)  

mscAal1CesAepProfile 1.3.6.1.4.1.562.36.2.1.119.3.11.1.3
This attribute specifies the PORS routing profile to use for this connection. If profile is empty, PORS will provide a default profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

mscAal1CesAepFirstRetryInterval 1.3.6.1.4.1.562.36.2.1.119.3.11.1.4
This attribute specifies the time to wait, in seconds, before attempting to establish the connection after the first failed attempt. The time to wait between subsequent call attempts will generally differ due to a backoff scheme.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..3600  

mscAal1CesAepRetryLimit 1.3.6.1.4.1.562.36.2.1.119.3.11.1.5
retryLimit specifies the maximum number of consecutive unsuccessful connection setup attempts that may be made before further attempts are abandoned. If this limit is reached, the Restart verb may be used to restart connection attempts. If retryLimit is 0, there is no limit; attempts will continue indefinitely until a successful connection is established.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

mscAal1CesAepActiveEndPointType 1.3.6.1.4.1.562.36.2.1.119.3.11.1.6
activeEndPointType specifies the type of end point: svc or softPvc. The default is svc. When activeEndPointType is svc, calledVpiVci is not relevant. When activeEndPointType is softPVC, routingOption must be atmOnly, and profile, firstRetryInterval, and retryLimit are not relevant.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER svc(0), softPVC(1)  

mscAal1CesAepCalledVpiVci 1.3.6.1.4.1.562.36.2.1.119.3.11.1.7
calledVpiVci specifies the identity of the PVC at the remote ATM node on which the softPVC connection terminates. calledVpiVci is relevant only when activeEndPointType is set to softPVC. The default value is 0.1
Status: mandatory Access: read-write
OBJECT-TYPE    
  IntegerSequence Size(3..10)  

mscAal1CesAepEpOperTable 1.3.6.1.4.1.562.36.2.1.119.3.12
This group contains general operational attributes for components using switched virtual circuits.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesAepEpOperEntry

mscAal1CesAepEpOperEntry 1.3.6.1.4.1.562.36.2.1.119.3.12.1
An entry in the mscAal1CesAepEpOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesAepEpOperEntry  

mscAal1CesAepRemoteAddress 1.3.6.1.4.1.562.36.2.1.119.3.12.1.1
remoteAddress is the address of the remote end point. If a connection is currently established, remoteAddress will contain the address of the remote end point. If a connection is not established, remoteAddress will be Unknown.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(7..40)  

mscAal1CesAepLastTearDownCause 1.3.6.1.4.1.562.36.2.1.119.3.12.1.2
lastTearDownCause indicates the cause of the last connection tear down. The values are as defined in the ATM Forum ATM User-Network Interface (UNI) Specification.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

mscAal1CesAepLastTearDownDiagnostic 1.3.6.1.4.1.562.36.2.1.119.3.12.1.3
lastTearDownDiagnostic provides a diagnostic to supplement the lastTearDownCause attribute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(0..8)  

mscAal1CesAepOutTable 1.3.6.1.4.1.562.36.2.1.119.3.13
This group contains status information about the AAL1 Circuit Emulation Service ActiveEndPoint component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesAepOutEntry

mscAal1CesAepOutEntry 1.3.6.1.4.1.562.36.2.1.119.3.13.1
An entry in the mscAal1CesAepOutTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesAepOutEntry  

mscAal1CesAepSvcStatus 1.3.6.1.4.1.562.36.2.1.119.3.13.1.1
svcStatus indicates the status of the incoming and outgoing connections. When this attribute has the value initialising, it indicates that the component is initialising when first created; a connection has not been established, and no incoming setup requests will be processed. When this attribute has the value connecting, it indicates that a connection has not yet been established, but that incoming setup requests will be processed. When this attribute has the value connected, it indicates that a connection has been established. When this attribute has the value retriesExhausted, it indicates that retryLimit consecutive connection setup attempts have failed, and the connection procedure has been aborted. When this attribute has the value idle, it indicates that a connection has not been established, and that no incoming setup requests will be processed. When this attribute has the value failed, it indicates that the connections is in a state other than those described above.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER initialising(0), connecting(1), connected(2), idle(3), retriesExhausted(4), failed(5)  

mscAal1CesAepLastSetupFailureCause 1.3.6.1.4.1.562.36.2.1.119.3.13.1.2
lastSetupFailureCause indicates the cause of the last connection setup failure. The values are as defined in the ATM Forum ATM User- Network Interface (UNI) Specification.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

mscAal1CesAepLastSetupFailureDiagnostic 1.3.6.1.4.1.562.36.2.1.119.3.13.1.3
lastSetupFailureDiagnostic provides a diagnostic to supplement the lastSetupFailureCause attribute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(0..8)  

mscAal1CesAepRetryTimeRemaining 1.3.6.1.4.1.562.36.2.1.119.3.13.1.4
retryTimerValue is the current value of the retry timer for this connection; it indicates the number of seconds before the next connection attempt will be made. retryTimerValue is initialized when a connection attempt fails. When retryTimerValue reaches 0, an attempt will be made to establish the connection. When the timer is not running, for example when the connection has been established, retryTimerValue will be 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscAal1CesAepRetryFailures 1.3.6.1.4.1.562.36.2.1.119.3.13.1.5
retryFailures counts the number of consecutive failed connection attempts. retryFailures is reset to 0 whenever a connection is successfully established, or the connection is restarted using the Restart verb. The counter wraps when the maximum value is exceeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscAal1CesPep 1.3.6.1.4.1.562.36.2.1.119.4
OBJECT IDENTIFIER    

mscAal1CesPepRowStatusTable 1.3.6.1.4.1.562.36.2.1.119.4.1
This entry controls the addition and deletion of mscAal1CesPep components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesPepRowStatusEntry

mscAal1CesPepRowStatusEntry 1.3.6.1.4.1.562.36.2.1.119.4.1.1
A single entry in the table represents a single mscAal1CesPep component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesPepRowStatusEntry  

mscAal1CesPepRowStatus 1.3.6.1.4.1.562.36.2.1.119.4.1.1.1
This variable is used as the basis for SNMP naming of mscAal1CesPep components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mscAal1CesPepComponentName 1.3.6.1.4.1.562.36.2.1.119.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscAal1CesPepStorageType 1.3.6.1.4.1.562.36.2.1.119.4.1.1.4
This variable represents the storage type value for the mscAal1CesPep tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscAal1CesPepIndex 1.3.6.1.4.1.562.36.2.1.119.4.1.1.10
This variable represents the index for the mscAal1CesPep tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mscAal1CesPepProvEndPointAddrTable 1.3.6.1.4.1.562.36.2.1.119.4.10
This group contains NSAP address provisioning data for components using switched virtual circuits.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesPepProvEndPointAddrEntry

mscAal1CesPepProvEndPointAddrEntry 1.3.6.1.4.1.562.36.2.1.119.4.10.1
An entry in the mscAal1CesPepProvEndPointAddrTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesPepProvEndPointAddrEntry  

mscAal1CesPepExpectedRemoteAddress 1.3.6.1.4.1.562.36.2.1.119.4.10.1.1
This attribute specifies the expected remote address prefix for an incoming connection setup request. If expectedRemoteAddress is not empty, only matching connections will be considered for acceptance. If expectedRemoteAddress is 40 characters long, the remote address must match exactly to be accepted. If expectedRemoteAddress is less than 40 characters long, the remote address must begin with expectedRemoteAddress to be accepted. If expectedRemoteAddress is empty, the component will process connection requests from any remote address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(0..40)  

mscAal1CesPepLocalAddress 1.3.6.1.4.1.562.36.2.1.119.4.10.1.2
This attribute specifies the local NSAP address. If the switch prefix (the nodePrefix attribute of the ModuleData component) has been provisioned, a default value for localAddress based on nodePrefix will be provided. If ModuleData nodePrefix has not been provisioned and one or more alternate switch prefixes (the alternatePorsPrefixes attribute of the ModuleData component) have been provisioned, a default value for localAddress based on the first provisioned alternatePorsPrefix value will be provided. If no switch prefixes have been provisioned, localAddress will default to an empty string. To obtain a valid default localAddress in this case, either or both of the ModuleData nodePrefix and ModuleData alternatePorsPrefixes attributes must be provisioned, and this end point component must then be deleted and re-added.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(40)  

mscAal1CesPepEpOperTable 1.3.6.1.4.1.562.36.2.1.119.4.11
This group contains general operational attributes for components using switched virtual circuits.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesPepEpOperEntry

mscAal1CesPepEpOperEntry 1.3.6.1.4.1.562.36.2.1.119.4.11.1
An entry in the mscAal1CesPepEpOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesPepEpOperEntry  

mscAal1CesPepRemoteAddress 1.3.6.1.4.1.562.36.2.1.119.4.11.1.1
remoteAddress is the address of the remote end point. If a connection is currently established, remoteAddress will contain the address of the remote end point. If a connection is not established, remoteAddress will be Unknown.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(7..40)  

mscAal1CesPepLastTearDownCause 1.3.6.1.4.1.562.36.2.1.119.4.11.1.2
lastTearDownCause indicates the cause of the last connection tear down. The values are as defined in the ATM Forum ATM User-Network Interface (UNI) Specification.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

mscAal1CesPepLastTearDownDiagnostic 1.3.6.1.4.1.562.36.2.1.119.4.11.1.3
lastTearDownDiagnostic provides a diagnostic to supplement the lastTearDownCause attribute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(0..8)  

mscAal1CesPepPassiveOperTable 1.3.6.1.4.1.562.36.2.1.119.4.12
This group contains status information about the AAL1 Circuit Emulation Service PassiveEndPoint component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesPepPassiveOperEntry

mscAal1CesPepPassiveOperEntry 1.3.6.1.4.1.562.36.2.1.119.4.12.1
An entry in the mscAal1CesPepPassiveOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesPepPassiveOperEntry  

mscAal1CesPepSvcStatus 1.3.6.1.4.1.562.36.2.1.119.4.12.1.1
svcStatus indicates the status of the incoming connection. When this attribute has the value initialising, it indicates that the component is initialising when first created; a connection has not been established, and no incoming setup requests will be processed. When this attribute has the value connecting, it indicates that a connection has not yet been establised, but that incoming setup requests will be processed. When this attribute has the value connected, it indicates that a connection has been established. When this attribute has the value idle, it indicates that a connection has not been established, and that no incoming setup requests will be processed. When this attribute has the value failed, it indicates that the connections is in a state other than those described above.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER initialising(0), connecting(1), connected(2), idle(3), failed(5)  

mscAal1CesLCo 1.3.6.1.4.1.562.36.2.1.119.5
OBJECT IDENTIFIER    

mscAal1CesLCoRowStatusTable 1.3.6.1.4.1.562.36.2.1.119.5.1
This entry controls the addition and deletion of mscAal1CesLCo components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesLCoRowStatusEntry

mscAal1CesLCoRowStatusEntry 1.3.6.1.4.1.562.36.2.1.119.5.1.1
A single entry in the table represents a single mscAal1CesLCo component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesLCoRowStatusEntry  

mscAal1CesLCoRowStatus 1.3.6.1.4.1.562.36.2.1.119.5.1.1.1
This variable is used as the basis for SNMP naming of mscAal1CesLCo components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mscAal1CesLCoComponentName 1.3.6.1.4.1.562.36.2.1.119.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscAal1CesLCoStorageType 1.3.6.1.4.1.562.36.2.1.119.5.1.1.4
This variable represents the storage type value for the mscAal1CesLCo tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscAal1CesLCoIndex 1.3.6.1.4.1.562.36.2.1.119.5.1.1.10
This variable represents the index for the mscAal1CesLCo tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mscAal1CesLCoPathDataTable 1.3.6.1.4.1.562.36.2.1.119.5.10
This group contains all operational attributes for the path oriented LCo.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesLCoPathDataEntry

mscAal1CesLCoPathDataEntry 1.3.6.1.4.1.562.36.2.1.119.5.10.1
An entry in the mscAal1CesLCoPathDataTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesLCoPathDataEntry  

mscAal1CesLCoState 1.3.6.1.4.1.562.36.2.1.119.5.10.1.1
This attribute reflects the current state of the connection. The pathDown state indicates a connection that has no remote end provisioned or the application has not yet signalled for a path. The selectingRoute state occurs when a request has been sent to route selector and it has not yet responded. The connectingState occurs while a path is being established. The pathUp state is the normal operational state of a path. The pathDownRetrying state indicates a path that attempted route selection but received no route and is now waiting to retry route selection again.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER pathDown(0), selectingRoute(1), connecting(2), pathUp(3), pathDownRetrying(4)  

mscAal1CesLCoOverrideRemoteName 1.3.6.1.4.1.562.36.2.1.119.5.10.1.2
If set and the current PLC remoteName is blank this remoteName will override the blank PLC remoteName. Usually you would set this attribute and then lock/unlock the service component which will result in this new overrideRemoteName being used as if it had been provisioned into the PLC remoteName. The advantage of this attribute is that the connection's remoteName can be changed immediately without having to 'activate prov' but the disadvantage is that the overrideRemoteName is not permanent and if the card or switch is reset the override will be lost.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(0..40)  

mscAal1CesLCoEnd 1.3.6.1.4.1.562.36.2.1.119.5.10.1.3
This attribute identifies whether this is the calling or called end of the path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER calling(0), called(1)  

mscAal1CesLCoCostMetric 1.3.6.1.4.1.562.36.2.1.119.5.10.1.4
This attribute gives the route's total cost metric. It is calculated as the sum of the cost metric of all trunks in the path at the time the connection was established. The cost metric of a trunk is defined by the trunkCost attribute of the Trunk component. The costMetric for an LCo that is originated and terminated on the same module is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

mscAal1CesLCoDelayMetric 1.3.6.1.4.1.562.36.2.1.119.5.10.1.5
This attribute gives the total delay of the route as the one way delay for a 512 byte packet. It is calculated as the sum of the delays of all trunks in the path stored in topology at the time the connection was established. The delay for an LCo that is originated and terminated on the same module is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

mscAal1CesLCoRoundTripDelay 1.3.6.1.4.1.562.36.2.1.119.5.10.1.6
This attribute contains the time taken for a packet (cell) of 44 bytes to be transmitted to the remote LCo and return to this LCo. The number reported is given in milliseconds to the nearest millisecond. A value of one millisecond is reported if the time is less than 1 millisecond even though the delay may be less than 1 Millisecond when the LCo is originated and terminated on the same module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..200000  

mscAal1CesLCoSetupPriority 1.3.6.1.4.1.562.36.2.1.119.5.10.1.7
This attribute gives the priority at which the current path is established. Zero is the highest priority and four is the lowest. The holdingPriority, a complementary attribute of this component, indicates the priority a path maintains once it is established.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4  

mscAal1CesLCoHoldingPriority 1.3.6.1.4.1.562.36.2.1.119.5.10.1.8
This attribute gives the priority at which a path holds its current path once the path is established. Zero is the highest priority and four is the lowest. The setupPriority, a complementary attribute, indicates the priority of a path at establishment time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4  

mscAal1CesLCoRequiredTxBandwidth 1.3.6.1.4.1.562.36.2.1.119.5.10.1.9
This attribute gives the actual bandwidth (in bits per second) reserved by this path on each of the trunks of its route. This attribute represents the bandwidth for traffic outgoing to the remote end point. The originating end of the connection determines this value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..4294967295  

mscAal1CesLCoRequiredRxBandwidth 1.3.6.1.4.1.562.36.2.1.119.5.10.1.10
This attribute gives the actual bandwidth (in bits per second) reserved by this path on each of trunks of its route. This attribute represents the bandwidth for traffic incoming from the remote end point. The originating end of the connection determines this value
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..4294967295  

mscAal1CesLCoRequiredTrafficType 1.3.6.1.4.1.562.36.2.1.119.5.10.1.11
This operational attribute indicates the type of traffic transmitted over the path. There are eight possible traffic types, and the path can transmit only one of them. The originating end of the connection determines the type. These are arbitrary designations for traffic type. The voice, data and video traffic types are defined, and five other arbitrary traffic types can be defined by the network administration. This attribute is used in the route selection process to restrict the route to trunks that support this traffic type. The supportedTrafficType trunk attribute lists all the types of traffic allowed on the trunk. For example, if requiredTrafficType is specified as trafficType1 then only trunks that include trafficType1 in supportedTrafficType, will be candidates for this connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER voice(0), data(1), video(2), trafficType1(3), trafficType2(4), trafficType3(5), trafficType4(6), trafficType5(7)  

mscAal1CesLCoPermittedTrunkTypes 1.3.6.1.4.1.562.36.2.1.119.5.10.1.12
This operational attribute lists up to eight types of trunk that can be used on the route. The originating end of the connection determines the types. The terrestrial and satellite trunk types have been defined, leaving six remaining arbitrary types that can be defined by the network administration. The trunk's type is indicated in the trunkType attribute of the Trunk component. When selecting a route, PORS only chooses trunks whose trunkType are in the permittedTrunkTypes for the path. Description of bits: terrestrial(0) satellite(1) trunkType1(2) trunkType2(3) trunkType3(4) trunkType4(5) trunkType5(6) trunkType6(7)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mscAal1CesLCoRequiredSecurity 1.3.6.1.4.1.562.36.2.1.119.5.10.1.13
This attribute indicates the required minimum level of security of the trunks on the route. Zero represents the most secure and seven represents the least secure. The trunk's security is indicated by the trunkSecurity attribute of the Trunk component, and has values identical in range and meaning to the requiredSecurity attribute. PORS ensures that any route selected does not contain a trunk whose trunkSecurity attribute is numerically greater than the requiredSecurity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..7  

mscAal1CesLCoRequiredCustomerParameter 1.3.6.1.4.1.562.36.2.1.119.5.10.1.14
This attribute indicates the allowed customer defined parameter of the trunks on the route.The originating end of the connection determines the customer defined parameter. Its value, a number from zero to seven, is chosen by a network administration to have a meaning specific to their network, thus allowing them to customize the use of their trunks. A complementary trunk attribute, customerParameter, also has a value from zero to seven. The route selection process does not consider trunks whose customerParameter is greater than the requiredCustomerParameter of the path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..7  

mscAal1CesLCoEmissionPriority 1.3.6.1.4.1.562.36.2.1.119.5.10.1.15
This attribute indicates the urgency with which packets on the path are emitted by the trunks on the route. The originating end of the connection selects the emissionPriority. EmissionPriority of zero indicates the highest emission priority, while two indicates the lowest emission priority. Packets with a higher emissionPriority (or numerically less) are serviced and sent out before the packets of lower emissionPriority (or numerically higher).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..2  

mscAal1CesLCoDiscardPriority 1.3.6.1.4.1.562.36.2.1.119.5.10.1.16
This attribute indicates the importance of the packets on the path.The originating end of the connection sets discardPriority. One is used for paths carrying the most important traffic, and three is used for paths carrying the least important traffic. Packets with lower discardPriority(numerically lower) are discarded after packets with a higher discardPriority(numerically higher).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 1..3  

mscAal1CesLCoPathType 1.3.6.1.4.1.562.36.2.1.119.5.10.1.17
This attribute indicates whether the path for this PLC was determined automatically or by static provisioning. Normal pathTypes are selected automatically by Route Selector.The other pathTypes are both manual pathTypes where the operator must specify, through provisioning, a static route termed the manualPath. A manual pathType connection is nearly identical to a normal path type connection with the exception that the route is pre-provisioned. For a manual pathType, bandwidth reservations are respected along the path exactly as in a normal path. The last type, the forced pathType, is also a manual path but regardless of the bandwidth available the route is granted provided the trunks are operational and there are sufficient Logical Channels (LChs). The forced pathType could result in over committing the reserved bandwidth allowed on a trunk. A better way to achieve the effects of a forced pathType is to use a manual pathType with setupPriority = 0 and holdingPriority = 0. In this manner the path will reserve correct bandwidth and it will bump other paths if required while not being bumped itself.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(0), manual(1), forced(2)  

mscAal1CesLCoRetryCount 1.3.6.1.4.1.562.36.2.1.119.5.10.1.18
This attribute is the count of the number of times the path chosen during route selection could not be instantiated. This count should be three or below if the network is performing adequately. A high value indicates that the route selection is often performed using an out-of-date view of available network bandwidth and/or topology. This attribute will only increase at the calling end of the connection. This attribute is reset each time a path reconnects and stops counting when it reaches its maximum value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

mscAal1CesLCoPathFailureCount 1.3.6.1.4.1.562.36.2.1.119.5.10.1.19
This attribute is the count of the number of times the path has successfully connected. It is set to zero the first time the path is up. If a path fails anytime after connecting this count will be incremented when the path is up again. Failed route requests do not count in this statistic. See retryCount above. This attribute stops counting at its maximum value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

mscAal1CesLCoReasonForNoRoute 1.3.6.1.4.1.562.36.2.1.119.5.10.1.20
This attribute is the route selection's reasonForNoRoute and provides a brief reason for which a route was not selected. The reasons are essentially self-explanatory. Perhaps two reasons for no route require some explanation. The reason unknownRemoteNodeName is issued when the remote node name is not in the topological database. The reason plcAttributesNotMet is issued when there is no network connectivity at a level specified by the PLC attributes. This reason is also issued when there is no physical connectivity between two end nodes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(0), destinationNameTooLong(1), destinationNotSpecified(2), unknownDestinationName(3), incorrectDestination(4), incorrectDestinationEndPoint(5), unknownSource(6), unknownDestination(7), sameNode(8), routeCostTooMuch(9), routesDelayTooLong(10), attributesNotMet(11), anError(12), attributeProfileProblem(13), manualPathIndexProblem(14)  

mscAal1CesLCoLastTearDownReason 1.3.6.1.4.1.562.36.2.1.119.5.10.1.21
This attribute reflects the last tear down reason for a connection (LCo). In many cases this displays the reason for a momentary service interruption. This attribute applies to the last path failure only. If a path is no longer up, this may give an indication to the reason that the path has failed. In many cases an alarm will also be generated with more specific information. The following is a brief description of the reasons: none - This path has no information for the teardown this is typical of a path provisioned with no remoteName that has not been up. normalShutDown - This path has gone down due to normal call termination. insufficientTxLcOrBandwidth - At present there is either no available bandwidth or logical channel numbers available on one or more of the trunks for this path in the transmit direction. insufficientRxLcOrBandwidth - At present there is either no available bandwidth or logical channel numbers available on one or more of the trunks for this path in the receive direction. trunkFailure- A trunk on the path has failed or has gone down due to a provisioning change of a critical attribute. trunkCardFailure- A trunk FP card has failed along the path. accessCardFailure- The FP on which the peer access service was running has failed. operatorForced- The path has terminated due to the operator locking a trunk along the path. lostLcnClash- The path has terminated because the PA's at both ends of an intermediate trunk have allocated the same LC to different calls. When this happens both calls must go down and then try to come up again a fraction of a second later (effectively ensuring that they will now be assigned different LC's). It is normal to get the odd clash especially when the PA's usedLC is approaching the PA's maxLC. networkCongestion - The path has failed due to control information being lost and not recoverable. trunkNotFound - Occurs on a manual path usually. Check for trunks not up or names provisioned incorrectly. farEndNotFound - The far end is not provisioned or is not up. Check remote Name. wrongModuleReached - This may occur on a manual path. Check provisioning for correct trunk and service names. For a normal path, the network Topology may be changing check remoteName. farEndBusy - The far end has been reached but it is busy. Check remoteName and remote end provisioning. callLoopedBack - This LCo is provisioned to call itself. Re- provision since this is invalid. unknownReason - The failure was not resolved. farEndNotReady - The remote end was reached but the connection was refused due to the remote end not being enabled. remoteNameMismatch - The remote end has alarmed and rejected this setup due to remoteName provisioning. serviceTypeMismatch - The remote Service Type does not match this service type. Check provisioning. reconnectFromFarEnd - The remote end re-established this connection. Check the remote end lastTearDownReason to determine the real reason. bumped - Another call bumped this path from a trunk to get bandwidth (or an LC) which it required to come up. This other path had a higher setupPriority than this path's holdingPriority hence it was allowed to steal the bandwidth (or LC) from this path. optimized - This call has been rerouted due to the optimization feature. The call is still active this just indicates why the path changed. trunkOrFarEndDidNotSupportMode - This call was unable to complete because a mode required by the service was not supported by one of the trunks the route went through or by the far end service it connected to. Currently the only mode that this applies to is the map/mux mode on TRUNK PA ATM component. Map mode was required by the application (CES/FrAtm etc.) but was not available on the TRUNK PA ATM component through which the call was routed or the far end CES/FrAtm component did not specify the same mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(0), normalShutDown(1), insufficientTxLcOrBandwidth(2), insufficientRxLcOrBandwidth(3), trunkFailure(4), trunkCardFailure(5), operatorForced(6), lostLcnClash(7), networkCongestion(8), trunkNotFound(9), farEndNotFound(10), wrongModuleReached(11), farEndBusy(12), callLoopedBack(13), unknownReason(14), farEndNotReady(15), remoteNameMismatch(16), serviceTypeMismatch(17), reconnectFromFarEnd(18), bumped(19), accessCardFailure(20), optimized(21), overrideRemoteName(22), trunkOrFarEndDidNotSupportMode(23)  

mscAal1CesLCoPathFailureAction 1.3.6.1.4.1.562.36.2.1.119.5.10.1.22
This attribute displays whether the application is set to tolerate momentary interruption of a path while a new path is selected. If disconnectConnection is displayed, the application is informed as soon as possible about a failure by disconnection. If the attribute displays reRoutePath, the path may attempt an immediate reroute, provided the failure is a recoverable failure. If rerouting fails the application is informed of the failure. With this option set to reRoutePath the LCo may wait up to 30 seconds before informing the service of complete disconnection in order to allow both ends to attempt to reconnect. Note that if PLC components are different at both ends only the calling end is allowed to reconnect. All pathTypes respect this attribute. Also on a manualPath with both ends provisioned with independent paths (at least with respect to the failure) this option will have the desired effect that the path is rerouted without complete disconnection at both ends
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disconnectConnection(0), reRoutePath(1)  

mscAal1CesLCoBumpPreference 1.3.6.1.4.1.562.36.2.1.119.5.10.1.23
This attribute specifies when bumping will occur during route selection process. Bumping may occur when necessary or always. It will be necessary for a connection to bump if there is not enough resources for the connection to be established and these resources are occupied by a connection whose setupPriority is lower (numerically higher) than the connection's setupPriority. A connection may also always bump in order to obtain the best route.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER bumpWhenNecessary(0), bumpToObtainBestRoute(1)  

mscAal1CesLCoOptimization 1.3.6.1.4.1.562.36.2.1.119.5.10.1.24
This attribute is used to specify whether this connection should attempt to optimize its path when requested by the routing PORS component. Every path is as optimal as it can be when it is established, but as network traffic patterns and configurations change this path may no longer be as optimal as it could be. The PORS connection manager on a module requests circuits to optimize at the optimization interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscAal1CesLCoPathUpDateTime 1.3.6.1.4.1.562.36.2.1.119.5.10.1.25
This is the time stamp when the current path was established or reestablished.
Status: mandatory Access: read-only
OBJECT-TYPE    
  EnterpriseDateAndTime Size(0|19)  

mscAal1CesLCoStatsTable 1.3.6.1.4.1.562.36.2.1.119.5.11
This group contains the operational statistics attributes for the path oriented LCo.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesLCoStatsEntry

mscAal1CesLCoStatsEntry 1.3.6.1.4.1.562.36.2.1.119.5.11.1
An entry in the mscAal1CesLCoStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesLCoStatsEntry  

mscAal1CesLCoPktsToNetwork 1.3.6.1.4.1.562.36.2.1.119.5.11.1.1
This attribute counts the number of packets transmitted to the network over this Logical Connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

mscAal1CesLCoBytesToNetwork 1.3.6.1.4.1.562.36.2.1.119.5.11.1.2
This attribute counts the number of bytes sent to the network over this Logical Connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

mscAal1CesLCoPktsFromNetwork 1.3.6.1.4.1.562.36.2.1.119.5.11.1.3
This attribute counts the number of packets received from the remote LCo via the network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

mscAal1CesLCoBytesFromNetwork 1.3.6.1.4.1.562.36.2.1.119.5.11.1.4
This attribute counts the number of bytes received from the remote LCo via the network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

mscAal1CesLCoPathTable 1.3.6.1.4.1.562.36.2.1.119.5.264
This attribute contains the trunk component names over which the path has been instantiated and the remote end point name terminating the path.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesLCoPathEntry

mscAal1CesLCoPathEntry 1.3.6.1.4.1.562.36.2.1.119.5.264.1
An entry in the mscAal1CesLCoPathTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesLCoPathEntry  

mscAal1CesLCoPathValue 1.3.6.1.4.1.562.36.2.1.119.5.264.1.1
This variable represents both the value and the index for the mscAal1CesLCoPathTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(0..40)  

mscAal1CesAtmCon 1.3.6.1.4.1.562.36.2.1.119.6
OBJECT IDENTIFIER    

mscAal1CesAtmConRowStatusTable 1.3.6.1.4.1.562.36.2.1.119.6.1
This entry controls the addition and deletion of mscAal1CesAtmCon components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesAtmConRowStatusEntry

mscAal1CesAtmConRowStatusEntry 1.3.6.1.4.1.562.36.2.1.119.6.1.1
A single entry in the table represents a single mscAal1CesAtmCon component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesAtmConRowStatusEntry  

mscAal1CesAtmConRowStatus 1.3.6.1.4.1.562.36.2.1.119.6.1.1.1
This variable is used as the basis for SNMP naming of mscAal1CesAtmCon components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mscAal1CesAtmConComponentName 1.3.6.1.4.1.562.36.2.1.119.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscAal1CesAtmConStorageType 1.3.6.1.4.1.562.36.2.1.119.6.1.1.4
This variable represents the storage type value for the mscAal1CesAtmCon tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscAal1CesAtmConIndex 1.3.6.1.4.1.562.36.2.1.119.6.1.1.10
This variable represents the index for the mscAal1CesAtmCon tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mscAal1CesAtmConOperTable 1.3.6.1.4.1.562.36.2.1.119.6.10
This attribute group contains the operational attributes for the NapAtmConnection component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscAal1CesAtmConOperEntry

mscAal1CesAtmConOperEntry 1.3.6.1.4.1.562.36.2.1.119.6.10.1
An entry in the mscAal1CesAtmConOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscAal1CesAtmConOperEntry  

mscAal1CesAtmConNextHop 1.3.6.1.4.1.562.36.2.1.119.6.10.1.1
This attribute shows the component name of the AtmIf Vcc Ep or AtmCon component to which this switched connection is established.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowPointer  

mscMmTx 1.3.6.1.4.1.562.36.2.1.151
OBJECT IDENTIFIER    

mscMmTxRowStatusTable 1.3.6.1.4.1.562.36.2.1.151.1
This entry controls the addition and deletion of mscMmTx components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscMmTxRowStatusEntry

mscMmTxRowStatusEntry 1.3.6.1.4.1.562.36.2.1.151.1.1
A single entry in the table represents a single mscMmTx component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscMmTxRowStatusEntry  

mscMmTxRowStatus 1.3.6.1.4.1.562.36.2.1.151.1.1.1
This variable is used as the basis for SNMP naming of mscMmTx components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mscMmTxComponentName 1.3.6.1.4.1.562.36.2.1.151.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscMmTxStorageType 1.3.6.1.4.1.562.36.2.1.151.1.1.4
This variable represents the storage type value for the mscMmTx tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscMmTxIndex 1.3.6.1.4.1.562.36.2.1.151.1.1.10
This variable represents the index for the mscMmTx tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 1..15  

mscMmTxCidDataTable 1.3.6.1.4.1.562.36.2.1.151.10
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscMmTxCidDataEntry

mscMmTxCidDataEntry 1.3.6.1.4.1.562.36.2.1.151.10.1
An entry in the mscMmTxCidDataTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscMmTxCidDataEntry  

mscMmTxCustomerIdentifier 1.3.6.1.4.1.562.36.2.1.151.10.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

mscMmTxProvTable 1.3.6.1.4.1.562.36.2.1.151.11
This group contains basic provisioning data for the Maintenance Monitor Transmitter (MmTx). A MmTx represents a mono- directional AAL1 Circuit Emulation Service. AAL1 CES attributes in this group are essential information to the operator about the AAL1 CES service that must be matched in the Aal1Ces component that receives the monitored stream. The check escape checks that only one instance of a MaintenanceMonitorTx is linked to any one Lp.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscMmTxProvEntry

mscMmTxProvEntry 1.3.6.1.4.1.562.36.2.1.151.11.1
An entry in the mscMmTxProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscMmTxProvEntry  

mscMmTxLinkToLogicalProcessor 1.3.6.1.4.1.562.36.2.1.151.11.1.3
This attribute specifies the instance of a hardware component to which an instance of this component is linked. Only Lp components may be linked
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

mscMmTxMonitoredDirection 1.3.6.1.4.1.562.36.2.1.151.11.1.4
monitoredDirection specifies the direction of the monitored traffic. The default and only value is ingress.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ingress(0)  

mscMmTxServiceType 1.3.6.1.4.1.562.36.2.1.151.11.1.5
serviceType specifies the service type of the CES. The serviceType attribute in the receiving Aal1Ces component must have the same value as this attribute. The default and only value is basicStructured.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER basicStructured(1)  

mscMmTxPartialFill 1.3.6.1.4.1.562.36.2.1.151.11.1.6
partialFill specifies the number of octets that are carried in an ATM cell by the AAL1 CES service. A full cell contains 47 octets. The partialFill attribute in the receiving Aal1Ces component must have the same value as this attribute. The default and only value is 47. DESCRIPTION
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 47  

mscMmTxIdleSuppression 1.3.6.1.4.1.562.36.2.1.151.11.1.7
idleSuppression controls the suppression of idle cells. An idle cell is one in which the bytes of the ATM payload (up to the partialFill level) match the idlePattern. If idleSuppression is off, idle cells are not suppressed. If idleSuppression is on, at least 75% of cells are suppressed under idle conditions. The idleSuppression attribute in the receiving Aal1Ces component must have the same value as this attribute The default and only value is off.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0)  

mscMmTxStateTable 1.3.6.1.4.1.562.36.2.1.151.12
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscMmTxStateEntry

mscMmTxStateEntry 1.3.6.1.4.1.562.36.2.1.151.12.1
An entry in the mscMmTxStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscMmTxStateEntry  

mscMmTxAdminState 1.3.6.1.4.1.562.36.2.1.151.12.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscMmTxOperationalState 1.3.6.1.4.1.562.36.2.1.151.12.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscMmTxUsageState 1.3.6.1.4.1.562.36.2.1.151.12.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscMmTxAvailabilityStatus 1.3.6.1.4.1.562.36.2.1.151.12.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

mscMmTxProceduralStatus 1.3.6.1.4.1.562.36.2.1.151.12.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mscMmTxControlStatus 1.3.6.1.4.1.562.36.2.1.151.12.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mscMmTxAlarmStatus 1.3.6.1.4.1.562.36.2.1.151.12.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mscMmTxStandbyStatus 1.3.6.1.4.1.562.36.2.1.151.12.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER hotStandby(0), coldStandby(1), providingService(2), notSet(15)  

mscMmTxUnknownStatus 1.3.6.1.4.1.562.36.2.1.151.12.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

mscMmTxOperTable 1.3.6.1.4.1.562.36.2.1.151.13
This group contains status information about the AAL1 Circuit Emulation Service and the related ATM service, and the means to specify the Channel to be monitor.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscMmTxOperEntry

mscMmTxOperEntry 1.3.6.1.4.1.562.36.2.1.151.13.1
An entry in the mscMmTxOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscMmTxOperEntry  

mscMmTxConnectionStatus 1.3.6.1.4.1.562.36.2.1.151.13.1.3
This attribute indicates whether a service is non-operational because of a problem with the service interface side of the service (in which case, it is set to channelNotReady) or because of a problem with the ATM side of the service (in which case, it is set to atmNotConfigured or atmNotReady). When this attribute is set to channelNotReady, it is an indication that the corresponding Chan component (as defined by the attribute interfaceName) or the Chan component's parent port component (Lp/n Ds1/m or Lp/n E1/m) is locked. When this attribute is set to atmNotConfigured, it is an indication that no sub-component has been provisioned, and thus no ATM connection has been configured for the service. When this attribute is set to atmNotReady, it is an indication that the ATM connection with which the service is associated (as defined by a sub-component) has been lost or that it is currently unable to carry CES data. When this attribute is set to channelNotSpecified, it is an indication that the chanToMonitor attribute is not set to a valid channel. This attribute is set to connected when a service is operational (that is, the OSI attribute operationalState is enabled.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER connected(0), channelNotReady(1), atmNotReady(2), atmNotConfigured(3), channelNotSpecified(4)  

mscMmTxChanToMonitor 1.3.6.1.4.1.562.36.2.1.151.13.1.4
chanToMonitor specifies the LP, port (E1 or DS1), and channel to monitor. The LP must be the same LP specified in the provisionable attribute linkToLogicalProcessor. This attribute's value is of the form Lp/x E1/y Chan/z or Lp/x DS1/y Chan/z.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowPointer  

mscMmTxNap 1.3.6.1.4.1.562.36.2.1.151.2
OBJECT IDENTIFIER    

mscMmTxNapRowStatusTable 1.3.6.1.4.1.562.36.2.1.151.2.1
This entry controls the addition and deletion of mscMmTxNap components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscMmTxNapRowStatusEntry

mscMmTxNapRowStatusEntry 1.3.6.1.4.1.562.36.2.1.151.2.1.1
A single entry in the table represents a single mscMmTxNap component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscMmTxNapRowStatusEntry  

mscMmTxNapRowStatus 1.3.6.1.4.1.562.36.2.1.151.2.1.1.1
This variable is used as the basis for SNMP naming of mscMmTxNap components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mscMmTxNapComponentName 1.3.6.1.4.1.562.36.2.1.151.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscMmTxNapStorageType 1.3.6.1.4.1.562.36.2.1.151.2.1.1.4
This variable represents the storage type value for the mscMmTxNap tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscMmTxNapIndex 1.3.6.1.4.1.562.36.2.1.151.2.1.1.10
This variable represents the index for the mscMmTxNap tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mscMmTxNapProvTable 1.3.6.1.4.1.562.36.2.1.151.2.10
This group contains the provisioning data for the NailedUpAdaptationPoint component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscMmTxNapProvEntry

mscMmTxNapProvEntry 1.3.6.1.4.1.562.36.2.1.151.2.10.1
An entry in the mscMmTxNapProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscMmTxNapProvEntry  

mscMmTxNapAtmConnection 1.3.6.1.4.1.562.36.2.1.151.2.10.1.1
This attribute specifies the identity of the component to which the NailedUpAdaptationPoint is linked. This is an AtmIf Vcc NailedUpEndPoint or an AtmIf Vpt Vcc NailedUpEndPoint (the AAL1 cells are transported off the switch over an ATM UNI, where they are routed to the appropriate AAL1 entity at the other end by the ATM bearer service).
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

mscMmTxAtmCon 1.3.6.1.4.1.562.36.2.1.151.6
OBJECT IDENTIFIER    

mscMmTxAtmConRowStatusTable 1.3.6.1.4.1.562.36.2.1.151.6.1
This entry controls the addition and deletion of mscMmTxAtmCon components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscMmTxAtmConRowStatusEntry

mscMmTxAtmConRowStatusEntry 1.3.6.1.4.1.562.36.2.1.151.6.1.1
A single entry in the table represents a single mscMmTxAtmCon component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscMmTxAtmConRowStatusEntry  

mscMmTxAtmConRowStatus 1.3.6.1.4.1.562.36.2.1.151.6.1.1.1
This variable is used as the basis for SNMP naming of mscMmTxAtmCon components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mscMmTxAtmConComponentName 1.3.6.1.4.1.562.36.2.1.151.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscMmTxAtmConStorageType 1.3.6.1.4.1.562.36.2.1.151.6.1.1.4
This variable represents the storage type value for the mscMmTxAtmCon tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscMmTxAtmConIndex 1.3.6.1.4.1.562.36.2.1.151.6.1.1.10
This variable represents the index for the mscMmTxAtmCon tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mscMmTxAtmConOperTable 1.3.6.1.4.1.562.36.2.1.151.6.10
This attribute group contains the operational attributes for the NapAtmConnection component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscMmTxAtmConOperEntry

mscMmTxAtmConOperEntry 1.3.6.1.4.1.562.36.2.1.151.6.10.1
An entry in the mscMmTxAtmConOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscMmTxAtmConOperEntry  

mscMmTxAtmConNextHop 1.3.6.1.4.1.562.36.2.1.151.6.10.1.1
This attribute shows the component name of the AtmIf Vcc Ep or AtmCon component to which this switched connection is established.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowPointer  

circuitEmulationServiceGroup 1.3.6.1.4.1.562.36.2.2.55.1
OBJECT IDENTIFIER    

circuitEmulationServiceGroupCA 1.3.6.1.4.1.562.36.2.2.55.1.1
OBJECT IDENTIFIER    

circuitEmulationServiceGroupCA02 1.3.6.1.4.1.562.36.2.2.55.1.1.3
OBJECT IDENTIFIER    

circuitEmulationServiceGroupCA02A 1.3.6.1.4.1.562.36.2.2.55.1.1.3.2
OBJECT IDENTIFIER    

circuitEmulationServiceCapabilities 1.3.6.1.4.1.562.36.2.2.55.3
OBJECT IDENTIFIER    

circuitEmulationServiceCapabilitiesCA 1.3.6.1.4.1.562.36.2.2.55.3.1
OBJECT IDENTIFIER    

circuitEmulationServiceCapabilitiesCA02 1.3.6.1.4.1.562.36.2.2.55.3.1.3
OBJECT IDENTIFIER    

circuitEmulationServiceCapabilitiesCA02A 1.3.6.1.4.1.562.36.2.2.55.3.1.3.2
OBJECT IDENTIFIER    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor