ODSLANBlazer7000-MIB

File: ODSLANBlazer7000-MIB.mib (195587 bytes)

Imported modules

Imported symbols

enterprises	Gauge	NetworkAddress
IpAddress	Counter	TimeTicks
OBJECT-TYPE	TRAP-TYPE

Defined Types

EventValueType
INTEGER	none(1), integer(2), longInteger(3), string(4), octets(5), ipAddress(6), macAddress(7), timeTicks(8)

ResourceType
INTEGER	system(1), module(2), fan(3), temperatureSensor(4), interface(5), powerSupply(6), display(7), switchPort(8), bridge(9), vlan(10), aft(11), inboundGroupTable(12), outboundGroupTable(13), threeComMappingTable(14), event(15), alarm(16)

ResourceId
OBJECT IDENTIFIER

DisplayString
OCTET STRING

RowStatus
INTEGER	active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6)

MacAddress
OCTET STRING	Size(6)

BridgeId
OCTET STRING	Size(8)

Timeout
INTEGER

EventCategory
INTEGER	userDefined(1), coldstart(2), warmstart(3), linkUp(4), linkDown(5), newResource(6), deletedResource(7), tempStatus(8), configuration(9), scheduled(10), authentication(11), system(12), risingThreshold(13), fallingThreshold(14), fanStatus(15), powerStatus(16), status(17), bridgeNewRoot(18), bridgeTopChange(19), switchFabricStatus(20)

LanBlazer7000CommunityEntry
SEQUENCE
	lanBlazer7000CommunityIndex	INTEGER
	lanBlazer7000CommunityString	DisplayString
	lanBlazer7000CommunityAddressType	INTEGER
	lanBlazer7000CommunityAddress	NetworkAddress
	lanBlazer7000CommunityAccess	INTEGER
	lanBlazer7000CommunityTrapReceiver	INTEGER
	lanBlazer7000CommunitySecurityLevel	INTEGER
	lanBlazer7000CommunityStatus	RowStatus

LanBlazer7000InventoryEntry
SEQUENCE
	lanBlazer7000InventoryResourceType	ResourceType
	lanBlazer7000InventoryResourceIndex	ResourceId
	lanBlazer7000InventoryModelNumber	DisplayString
	lanBlazer7000InventorySerialNumber	DisplayString
	lanBlazer7000InventoryVersion	DisplayString
	lanBlazer7000InventoryManufactureInfo	DisplayString
	lanBlazer7000InventoryScratchPad	DisplayString

LanBlazer7000PowerSupplyEntry
SEQUENCE
	lanBlazer7000PowerSupplyIndex	ResourceId
	lanBlazer7000PowerSupplyType	INTEGER
	lanBlazer7000PowerSupplyStatus	INTEGER
	lanBlazer7000PowerSupplyInputStatus	INTEGER
	lanBlazer7000PowerSupplyOutputStatus	INTEGER
	lanBlazer7000PowerSupplyOutputCapacity	INTEGER

LanBlazer7000PowerControlEntry
SEQUENCE
	lanBlazer7000PowerControlUsed	INTEGER
	lanBlazer7000PowerControlPriority	INTEGER
	lanBlazer7000PowerControlMode	INTEGER

LanBlazer7000TempEntry
SEQUENCE
	lanBlazer7000TempIndex	ResourceId
	lanBlazer7000TempValue	INTEGER
	lanBlazer7000TempUpperLimit	INTEGER
	lanBlazer7000TempUpperWarning	INTEGER
	lanBlazer7000TempLowerWarning	INTEGER
	lanBlazer7000TempLowerLimit	INTEGER

LanBlazer7000ModuleEntry
SEQUENCE
	lanBlazer7000ModuleIndex	ResourceId
	lanBlazer7000ModuleName	DisplayString
	lanBlazer7000ModuleType	INTEGER
	lanBlazer7000ModuleBaseType	INTEGER
	lanBlazer7000ModuleSlotWidth	INTEGER
	lanBlazer7000ModuleSlotOffset	INTEGER
	lanBlazer7000ModulePorts	INTEGER

LanBlazer7000PortEntry
SEQUENCE
	lanBlazer7000PortIndex	ResourceId
	lanBlazer7000PortName	DisplayString
	lanBlazer7000PortType	INTEGER
	lanBlazer7000PortBaseType	INTEGER
	lanBlazer7000PortMode	INTEGER
	lanBlazer7000PortStatus	INTEGER
	lanBlazer7000PortConnector	INTEGER
	lanBlazer7000PortSpeedState	INTEGER
	lanBlazer7000PortDuplexState	INTEGER
	lanBlazer7000PortGroupBinding	ResourceId

LanBlazer7000PortFlowControlEntry
SEQUENCE
	lanBlazer7000PortFlowControlMode	INTEGER

LanBlazer7000PortDuplexEntry
SEQUENCE
	lanBlazer7000PortDuplexMode	INTEGER

LanBlazer7000PortSpeedEntry
SEQUENCE
	lanBlazer7000PortSpeedMode	INTEGER

LanBlazer7000PortAutoNegotiationEntry
SEQUENCE
	lanBlazer7000PortAutoNegotiationMode	INTEGER
	lanBlazer7000PortAutoNegotiationSpeedAdvertisement	INTEGER
	lanBlazer7000PortAutoNegotiationDuplexAdvertisement	INTEGER

LanBlazer7000PortRateLimitEntry
SEQUENCE
	lanBlazer7000PortRateLimitMode	INTEGER
	lanBlazer7000PortRateLimitRate	INTEGER
	lanBlazer7000PortRateLimitBurstSize	INTEGER

LanBlazer7000PortPacePriorityEntry
SEQUENCE
	lanBlazer7000PortPacePriorityMode	INTEGER

LanBlazer7000PortCategoryEntry
SEQUENCE
	lanBlazer7000PortCategoryMode	INTEGER

LanBlazer7000BufferEntry
SEQUENCE
	lanBlazer7000BufferIndex	ResourceId
	lanBlazer7000BufferFabricPort	ResourceId
	lanBlazer7000BufferFabricPortDirection	INTEGER
	lanBlazer7000BufferSwitchPort	ResourceId
	lanBlazer7000BufferMemory	INTEGER
	lanBlazer7000BufferAgeTimer	INTEGER
	lanBlazer7000BufferPriorityServicing	INTEGER
	lanBlazer7000BufferPriorityAllocation	INTEGER
	lanBlazer7000BufferPriorityThreshold	INTEGER
	lanBlazer7000BufferCongestion	INTEGER
	lanBlazer7000BufferHighOverflowDrops	Counter
	lanBlazer7000BufferLowOverflowDrops	Counter
	lanBlazer7000BufferHighStaleDrops	Counter
	lanBlazer7000BufferLowStaleDrops	Counter
	lanBlazer7000BufferCongestionDrops	Counter

LanBlazer7000BridgeEntry
SEQUENCE
	lanBlazer7000BridgeIndex	ResourceId
	lanBlazer7000BridgeType	INTEGER
	lanBlazer7000BridgeMode	INTEGER
	lanBlazer7000BridgeStatus	INTEGER
	lanBlazer7000BridgeStpPriority	INTEGER
	lanBlazer7000BridgeStpTimeSinceTopologyChange	TimeTicks
	lanBlazer7000BridgeStpTopChanges	Counter
	lanBlazer7000BridgeStpDesignatedRoot	BridgeId
	lanBlazer7000BridgeStpRootCost	INTEGER
	lanBlazer7000BridgeStpRootPort	INTEGER
	lanBlazer7000BridgeStpMaxAge	Timeout
	lanBlazer7000BridgeStpHelloTime	Timeout
	lanBlazer7000BridgeStpHoldTime	INTEGER
	lanBlazer7000BridgeStpForwardDelay	Timeout
	lanBlazer7000BridgeStpBridgeMaxAge	Timeout
	lanBlazer7000BridgeStpBridgeHelloTime	Timeout
	lanBlazer7000BridgeStpBridgeForwardDelay	Timeout

LanBlazer7000BridgePortEntry
SEQUENCE
	lanBlazer7000BridgePortIndex	ResourceId
	lanBlazer7000BridgePortPriority	INTEGER
	lanBlazer7000BridgePortState	INTEGER
	lanBlazer7000BridgePortEnable	INTEGER
	lanBlazer7000BridgePortPathCost	INTEGER
	lanBlazer7000BridgePortDesignatedRoot	BridgeId
	lanBlazer7000BridgePortDesignatedCost	INTEGER
	lanBlazer7000BridgePortDesignatedBridge	BridgeId
	lanBlazer7000BridgePortDesignatedPort	OCTET STRING
	lanBlazer7000BridgePortForwardTransitions	Counter
	lanBlazer7000BridgePortFastStart	INTEGER
	lanBlazer7000BridgePortSetDefault	INTEGER
	lanBlazer7000BridgePortEnableChangeDetection	INTEGER

LanBlazer7000L2AddressEntry
SEQUENCE
	lanBlazer7000L2AddressIndex	INTEGER
	lanBlazer7000L2AddressTableIndex	INTEGER
	lanBlazer7000L2AddressMacAddress	MacAddress
	lanBlazer7000L2AddressPortBinding	ResourceId
	lanBlazer7000L2AddressBindingValid	INTEGER
	lanBlazer7000L2AddressVlanID	INTEGER
	lanBlazer7000L2AddressPriority	INTEGER
	lanBlazer7000L2AddressForward	INTEGER
	lanBlazer7000L2AddressCopy	INTEGER
	lanBlazer7000L2AddressPersistence	INTEGER
	lanBlazer7000L2AddressStatus	INTEGER

LanBlazer7000L2AddrSummaryEntry
SEQUENCE
	lanBlazer7000L2AddrSummary	OCTET STRING

LanBlazer7000L2AddressControlEntry
SEQUENCE
	lanBlazer7000L2AddressControlIndex	INTEGER
	lanBlazer7000L2AddressControlMacAddress	MacAddress
	lanBlazer7000L2AddressControlPortBinding	ResourceId
	lanBlazer7000L2AddressControlVlanID	INTEGER
	lanBlazer7000L2AddressControlPriority	INTEGER
	lanBlazer7000L2AddressControlPersistence	INTEGER
	lanBlazer7000L2AddressControlStatus	INTEGER

LanBlazer7000L2AddressChangeEntry
SEQUENCE
	lanBlazer7000L2AddressChangeWrapCount	INTEGER
	lanBlazer7000L2AddressChangeIndex	INTEGER
	lanBlazer7000L2AddressChangeIndexChanged	INTEGER
	lanBlazer7000L2AddressChangeSummary	OCTET STRING

LanBlazer7000SwitchPortEntry
SEQUENCE
	lanBlazer7000SwitchPortIndex	ResourceId
	lanBlazer7000SwitchPortSTAPMode	INTEGER
	lanBlazer7000SwitchPortConvertToStatic	INTEGER
	lanBlazer7000SwitchPortLearningMode	INTEGER
	lanBlazer7000SwitchPortHuntGroup	INTEGER
	lanBlazer7000SwitchPortPhysicalPort	ResourceId
	lanBlazer7000SwitchPortKnownMode	INTEGER
	lanBlazer7000SwitchPortMappingMethod	INTEGER
	lanBlazer7000SwitchPortTrunkingMode	INTEGER
	lanBlazer7000SwitchPortVlanBindingMethod	INTEGER
	lanBlazer7000SwitchPortIgnoreTag	INTEGER
	lanBlazer7000SwitchPortVlanID	INTEGER
	lanBlazer7000SwitchPort3ComMappingTableIndex	INTEGER
	lanBlazer7000SwitchPortAutoVlanCreation	INTEGER
	lanBlazer7000SwitchPortIfIndex	INTEGER
	lanBlazer7000SwitchPortFastStart	INTEGER
	lanBlazer7000SwitchPortVlanExchange	INTEGER

LanBlazer7000HuntGroupEntry
SEQUENCE
	lanBlazer7000HuntGroupIndex	INTEGER
	lanBlazer7000HuntGroupName	DisplayString
	lanBlazer7000HuntGroupBasePort	ResourceId
	lanBlazer7000HuntGroupNumberOfPorts	INTEGER
	lanBlazer7000HuntGroupLoadSharing	INTEGER
	lanBlazer7000HuntGroupStatus	INTEGER

LanBlazer7000PortMirroringEntry
SEQUENCE
	lanBlazer7000PortMirroringIndex	ResourceId
	lanBlazer7000PortMirroringSourceSubPort	INTEGER
	lanBlazer7000PortMirroringSamplerType	INTEGER
	lanBlazer7000PortMirroringRate	INTEGER
	lanBlazer7000PortMirroringMirrorPort	ResourceId

LanBlazer7000VlanEntry
SEQUENCE
	lanBlazer7000VlanID	INTEGER
	lanBlazer7000VlanName	DisplayString
	lanBlazer7000VlanIfIndex	INTEGER
	lanBlazer7000VlanAFTIndex	INTEGER
	lanBlazer7000VlanBridgeIndex	ResourceId
	lanBlazer7000VlanStatus	INTEGER
	lanBlazer7000VlanInitialHashTableSize	INTEGER
	lanBlazer7000VlanAutoIncrementHTSize	INTEGER
	lanBlazer7000VlanLearnStatus	INTEGER

LanBlazer70003ComMappingEntry
SEQUENCE
	lanBlazer70003ComMappingTableIndex	INTEGER
	lanBlazer70003ComMappingTableName	DisplayString
	lanBlazer70003ComMappingTableStatus	INTEGER

LanBlazer7000Vlan3ComMappingEntry
SEQUENCE
	lanBlazer7000Vlan3ComMappingIndex	INTEGER
	lanBlazer7000Vlan3ComMappingVlanID	INTEGER
	lanBlazer7000Vlan3ComMappingStatus	INTEGER

LanBlazer7000VirtualSwitchPortEntry
SEQUENCE
	lanBlazer7000VirtualSwitchPortIndex	ResourceId
	lanBlazer7000VirtualSwitchPortFormat	INTEGER
	lanBlazer7000VirtualSwitchPortBridgePort	ResourceId
	lanBlazer7000VirtualSwitchPortBindingType	INTEGER
	lanBlazer7000VirtualSwitchPortStatus	INTEGER

LanBlazer7000EventEntry
SEQUENCE
	lanBlazer7000EventIndex	INTEGER
	lanBlazer7000EventMode	INTEGER
	lanBlazer7000EventLogAction	INTEGER
	lanBlazer7000EventTrapAction	INTEGER
	lanBlazer7000EventConsoleAction	INTEGER

LanBlazer7000EventLogEntry
SEQUENCE
	lanBlazer7000EventLogEventIndex	INTEGER
	lanBlazer7000EventLogIndex	INTEGER
	lanBlazer7000EventLogTime	TimeTicks
	lanBlazer7000EventLogDescr	DisplayString
	lanBlazer7000EventLogType	EventCategory
	lanBlazer7000EventLogSeverity	INTEGER
	lanBlazer7000EventLogDTM	DisplayString
	lanBlazer7000EventLogResType	ResourceType
	lanBlazer7000EventLogResID	ResourceId
	lanBlazer7000EventLogResLeaf	INTEGER
	lanBlazer7000EventLogValueType	EventValueType
	lanBlazer7000EventLogValue	OCTET STRING
	lanBlazer7000EventLogEpochTime	INTEGER
	lanBlazer7000EventLogID	INTEGER

LanBlazer7000EventShutdownLogEntry
SEQUENCE
	lanBlazer7000EventShutdownLogEventIndex	INTEGER
	lanBlazer7000EventShutdownLogIndex	INTEGER
	lanBlazer7000EventShutdownLogTime	TimeTicks
	lanBlazer7000EventShutdownLogDescr	DisplayString
	lanBlazer7000EventShutdownLogType	EventCategory
	lanBlazer7000EventShutdownLogSeverity	INTEGER
	lanBlazer7000EventShutdownLogDTM	DisplayString
	lanBlazer7000EventShutdownLogResType	ResourceType
	lanBlazer7000EventShutdownLogResID	ResourceId
	lanBlazer7000EventShutdownLogResLeaf	INTEGER
	lanBlazer7000EventShutdownLogValueType	EventValueType
	lanBlazer7000EventShutdownLogValue	OCTET STRING
	lanBlazer7000EventShutdownLogEpochTime	INTEGER
	lanBlazer7000EventShutdownLogID	INTEGER

LanBlazer7000ActiveAlarmEntry
SEQUENCE
	lanBlazer7000ActiveAlarmIndex	INTEGER
	lanBlazer7000ActiveAlarmName	DisplayString
	lanBlazer7000ActiveAlarmValueHigh	INTEGER
	lanBlazer7000ActiveAlarmValueLow	INTEGER
	lanBlazer7000ActiveAlarmVariable	OBJECT IDENTIFIER
	lanBlazer7000ActiveAlarmResType	ResourceType
	lanBlazer7000ActiveAlarmResID	ResourceId
	lanBlazer7000ActiveAlarmLeaf	INTEGER
	lanBlazer7000ActiveAlarmOwner	DisplayString

Defined Values

ods		1.3.6.1.4.1.50
OBJECT IDENTIFIER

odsTPS		1.3.6.1.4.1.50.8
OBJECT IDENTIFIER

odsLANBlazer		1.3.6.1.4.1.50.8.1
OBJECT IDENTIFIER

odsLANBlazerMibs		1.3.6.1.4.1.50.8.1.2
OBJECT IDENTIFIER

odsLANBlazer7000Mib		1.3.6.1.4.1.50.8.1.2.1
OBJECT IDENTIFIER

lanBlazer7000Agent		1.3.6.1.4.1.50.8.1.2.1.1
OBJECT IDENTIFIER

lanBlazer7000AgentGen		1.3.6.1.4.1.50.8.1.2.1.1.1
OBJECT IDENTIFIER

lanBlazer7000AgentMIBVersion		1.3.6.1.4.1.50.8.1.2.1.1.1.1
The version of the LANBlazer 700 Enterprise Specific MIB that this agent supports.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

lanBlazer7000AgentMgrIndex		1.3.6.1.4.1.50.8.1.2.1.1.1.2
The value of this object represents the index into the community table that is used to authenticate SNMP requests for this manager.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000AgentCommunity		1.3.6.1.4.1.50.8.1.2.1.1.2
OBJECT IDENTIFIER

lanBlazer7000CommunityTable		1.3.6.1.4.1.50.8.1.2.1.1.2.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000CommunityEntry

lanBlazer7000CommunityEntry		1.3.6.1.4.1.50.8.1.2.1.1.2.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000CommunityEntry

lanBlazer7000CommunityIndex		1.3.6.1.4.1.50.8.1.2.1.1.2.1.1.1
An index that uniquely identifies this entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000CommunityString		1.3.6.1.4.1.50.8.1.2.1.1.2.1.1.2
The community string included in the SNMP PDU used for authentication purposes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

lanBlazer7000CommunityAddressType		1.3.6.1.4.1.50.8.1.2.1.1.2.1.1.3
The type of address associated with this community. If set to any(1), only the community string is authenticated.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	any(1), ipv4(2)

lanBlazer7000CommunityAddress		1.3.6.1.4.1.50.8.1.2.1.1.2.1.1.4
If the address type is any, then the value of this object is a null string. If the type is ipv4(2), then this value represents a 4 byte IP address.
Status: mandatory	Access: read-write
OBJECT-TYPE
	NetworkAddress

lanBlazer7000CommunityAccess		1.3.6.1.4.1.50.8.1.2.1.1.2.1.1.5
The MIB access supported for this community entry. A Get or GetNext SNMP PDU is authenticated if the value of this object is read-only(2) or read-write(3). A Set request will be honored if the value of this object is read-write(3). If more granular access control is desired, then the value of this object is set to more-specific(4), and the view table should be consulted. This enables the capability to set different access rights to different branches of the MIB for a particular community.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), readOnly(2), readWrite(3), moreSpecific(4)

lanBlazer7000CommunityTrapReceiver		1.3.6.1.4.1.50.8.1.2.1.1.2.1.1.6
If set to enable(1), this community entry is considered a trap receiver. When the agent generates an SNMP trap, a copy will be sent to this host using this community string.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

lanBlazer7000CommunitySecurityLevel		1.3.6.1.4.1.50.8.1.2.1.1.2.1.1.7
Secure tables are only accessible from users with security clearance. For example, this table (the community table) is only accessible by parties that have the security clearance.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), administrator(2)

lanBlazer7000CommunityStatus		1.3.6.1.4.1.50.8.1.2.1.1.2.1.1.8
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

lanBlazer7000AgentWeb		1.3.6.1.4.1.50.8.1.2.1.1.3
OBJECT IDENTIFIER

lanBlazer7000AgentWebServerURL		1.3.6.1.4.1.50.8.1.2.1.1.3.1
The URL of where the document server software is installed. The switch uses this location to find online help and bimapped graphics. Enter the host name or IP address of the HTTP server at the HTTP Server Location prompt, followed by ':2010'. For example, for a host named 'phantom,', enter 'http://phantom:2010'. If no server is desired or installed, set this object to the empty string.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..31)

lanBlazer7000AgentWebServerHelpDirectory		1.3.6.1.4.1.50.8.1.2.1.1.3.2
The subdirectory that contains the help files on the document server. Typically, this directory is 'help'.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..31)

lanBlazer7000Chassis		1.3.6.1.4.1.50.8.1.2.1.3
OBJECT IDENTIFIER

lanBlazer7000ChassisGen		1.3.6.1.4.1.50.8.1.2.1.3.1
OBJECT IDENTIFIER

lanBlazer7000ChassisType		1.3.6.1.4.1.50.8.1.2.1.3.1.1
The model of the chassis that this agent is managing.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	p550(1), p220(2)

lanBlazer7000ChassisSlots		1.3.6.1.4.1.50.8.1.2.1.3.1.2
The number of slots available in this chassis. If this chassis is a stackable chassis, the total capacity of stacking units.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000Inventory		1.3.6.1.4.1.50.8.1.2.1.3.2
OBJECT IDENTIFIER

lanBlazer7000InventoryTable		1.3.6.1.4.1.50.8.1.2.1.3.2.1
A table of inventory information.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000InventoryEntry

lanBlazer7000InventoryEntry		1.3.6.1.4.1.50.8.1.2.1.3.2.1.1
Inventory information related to this device.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000InventoryEntry

lanBlazer7000InventoryResourceType		1.3.6.1.4.1.50.8.1.2.1.3.2.1.1.1
The resource class of this inventory item.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceType

lanBlazer7000InventoryResourceIndex		1.3.6.1.4.1.50.8.1.2.1.3.2.1.1.2
The resource identifier of this inventory item.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000InventoryModelNumber		1.3.6.1.4.1.50.8.1.2.1.3.2.1.1.3
The model number of this device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

lanBlazer7000InventorySerialNumber		1.3.6.1.4.1.50.8.1.2.1.3.2.1.1.4
The serial number of this device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

lanBlazer7000InventoryVersion		1.3.6.1.4.1.50.8.1.2.1.3.2.1.1.5
The revision number of this device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

lanBlazer7000InventoryManufactureInfo		1.3.6.1.4.1.50.8.1.2.1.3.2.1.1.6
Information related to the manufacturing of this device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..128)

lanBlazer7000InventoryScratchPad		1.3.6.1.4.1.50.8.1.2.1.3.2.1.1.7
A scratch pad area available for keeping user-supplied inventory information.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..128)

lanBlazer7000PowerSystems		1.3.6.1.4.1.50.8.1.2.1.3.3
OBJECT IDENTIFIER

lanBlazer7000PowerSupplies		1.3.6.1.4.1.50.8.1.2.1.3.3.1
OBJECT IDENTIFIER

lanBlazer7000PowerSupplyTable		1.3.6.1.4.1.50.8.1.2.1.3.3.1.1
A table of information related to each power supply in the system.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000PowerSupplyEntry

lanBlazer7000PowerSupplyEntry		1.3.6.1.4.1.50.8.1.2.1.3.3.1.1.1
An entry providing information about a particular power supply in the system.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000PowerSupplyEntry

lanBlazer7000PowerSupplyIndex		1.3.6.1.4.1.50.8.1.2.1.3.3.1.1.1.1
An index that uniquely identifies this power supply. This index corresponds to the lanBlazer7000ResourceIndex of the power supply type resource.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000PowerSupplyType		1.3.6.1.4.1.50.8.1.2.1.3.3.1.1.1.2
An enumerated integer describing the type of power supply.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), psA(2), psB(3)

lanBlazer7000PowerSupplyStatus		1.3.6.1.4.1.50.8.1.2.1.3.3.1.1.1.3
The status of this power supply. Okay(1) indicates the power supply is operating properly. Faulty(2) indicates that the power supply is not functioning properly. In this case, more information can be determined from the other power supply attributes.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	okay(1), faulty(2), unknown(3)

lanBlazer7000PowerSupplyInputStatus		1.3.6.1.4.1.50.8.1.2.1.3.3.1.1.1.4
The status of the input power feed (e.g. the AC power cord) to this power supply.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	okay(1), faulty(2), unknown(3)

lanBlazer7000PowerSupplyOutputStatus		1.3.6.1.4.1.50.8.1.2.1.3.3.1.1.1.5
The status of the output power from this power supply.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	okay(1), faulty(2), unknown(3)

lanBlazer7000PowerSupplyOutputCapacity		1.3.6.1.4.1.50.8.1.2.1.3.3.1.1.1.6
The total capacity of power supplied by this supply in Watts.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000PowerMgmtGen		1.3.6.1.4.1.50.8.1.2.1.3.3.2
OBJECT IDENTIFIER

lanBlazer7000PowerCapacity		1.3.6.1.4.1.50.8.1.2.1.3.3.2.1
The total capacity (in Watts) of power available (currently) in the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000PowerUsed		1.3.6.1.4.1.50.8.1.2.1.3.3.2.2
The total power (in Watts) currently being consumed in the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000PowerMgmtCtl		1.3.6.1.4.1.50.8.1.2.1.3.3.3
OBJECT IDENTIFIER

lanBlazer7000PowerControlTable		1.3.6.1.4.1.50.8.1.2.1.3.3.3.1
This table manages the power attributes associated with each module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000PowerControlEntry

lanBlazer7000PowerControlEntry		1.3.6.1.4.1.50.8.1.2.1.3.3.3.1.1
An entry in the power control table manages the power attributes of the specified module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000PowerControlEntry

lanBlazer7000PowerControlUsed		1.3.6.1.4.1.50.8.1.2.1.3.3.3.1.1.1
The total power (in Watts) used by this module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000PowerControlPriority		1.3.6.1.4.1.50.8.1.2.1.3.3.3.1.1.2
The priority of this module to be considered in the event of a power supply failure where the amount of power used exceeds the system capacity. Low priority modules will be powered down before higher priority modules.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	high(1), normal(2), low(3)

lanBlazer7000PowerControlMode		1.3.6.1.4.1.50.8.1.2.1.3.3.3.1.1.3
Normally, a module power mode is enable(1). In the event of a power supply failure resulting in a power shortage, or in the event of this module being inserted without enough available power, the mode will be poweredDown(3). Setting this object to the value of poweredDown(3) will result in an error. When enough power is available, the module will power back up when in this mode. A module may be powered down through administrative action by setting the value of this object to disable(2). In this mode, the module will remain powered down until the mode is set back to enable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2), poweredDown(3)

lanBlazer7000Temperature		1.3.6.1.4.1.50.8.1.2.1.3.4
OBJECT IDENTIFIER

lanBlazer7000TempTable		1.3.6.1.4.1.50.8.1.2.1.3.4.1
A table of information related to the temperature within the system.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000TempEntry

lanBlazer7000TempEntry		1.3.6.1.4.1.50.8.1.2.1.3.4.1.1
An entry providing temperature information related to a specific temperature probe in the system.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000TempEntry

lanBlazer7000TempIndex		1.3.6.1.4.1.50.8.1.2.1.3.4.1.1.1
A unique index that identifies this temperature probe. This index corresponds to the lanBlazer7000ResourceIndex for temperature probe type resources.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000TempValue		1.3.6.1.4.1.50.8.1.2.1.3.4.1.1.2
The current temperature reading of this temperature probe in degrees Celsius.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000TempUpperLimit		1.3.6.1.4.1.50.8.1.2.1.3.4.1.1.3
The upper temperature limit of this temperature probe in degrees Celsius.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

lanBlazer7000TempUpperWarning		1.3.6.1.4.1.50.8.1.2.1.3.4.1.1.4
The upper temperature warning of this temperature probe in degrees Celsius.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

lanBlazer7000TempLowerWarning		1.3.6.1.4.1.50.8.1.2.1.3.4.1.1.5
The lower temperature warning of this temperature probe in degrees Celsius.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

lanBlazer7000TempLowerLimit		1.3.6.1.4.1.50.8.1.2.1.3.4.1.1.6
The lower temperature limit of this temperature probe in degrees Celsius.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

lanBlazer7000Modules		1.3.6.1.4.1.50.8.1.2.1.3.5
OBJECT IDENTIFIER

lanBlazer7000ModuleTable		1.3.6.1.4.1.50.8.1.2.1.3.5.1
A table of information related to the modules in the system.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000ModuleEntry

lanBlazer7000ModuleEntry		1.3.6.1.4.1.50.8.1.2.1.3.5.1.1
Attributes related to managing this module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000ModuleEntry

lanBlazer7000ModuleIndex		1.3.6.1.4.1.50.8.1.2.1.3.5.1.1.1
An index that uniquely identifies this module. This index corresponds to the lanBlazer7000ResourceIndex associated with module type resources.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000ModuleName		1.3.6.1.4.1.50.8.1.2.1.3.5.1.1.2
A user-assignable name for this module.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..31)

lanBlazer7000ModuleType		1.3.6.1.4.1.50.8.1.2.1.3.5.1.1.3
An enumerated integer that is unique for each module model.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), m5502-1000(2), m2206-1000(3), m5520-100TX-QS(4), m5510-100FX(5), m5500-SUP(6), m5504-1000(7), m2201-1000(8), m5520-100TX-I(9), m2202-100FX(10), m5510R-100FX(11), m5512R-100TX(12), m5500R-SUP(13), m5502R-1000(14), m2200-SUP(15), m2204-100TX(16), m2224-100TX(17)

lanBlazer7000ModuleBaseType		1.3.6.1.4.1.50.8.1.2.1.3.5.1.1.4
The base type of this module. This object is used to describe the core functions of the module. Often, base designs are derived into multiple module types which are typically just packaging variations (e.g. changing the connector types). The value of this object corresponds to the value of lanBlazer7000ResourceBaseType.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	gigabit(1), fastEthernet(2), supervisor(3)

lanBlazer7000ModuleSlotWidth		1.3.6.1.4.1.50.8.1.2.1.3.5.1.1.5
The number of slots that this module occupies.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000ModuleSlotOffset		1.3.6.1.4.1.50.8.1.2.1.3.5.1.1.6
The slot offset (one based) that identifies, along with the slot width and slot location, the actual slots that this module occupies. The offset identifies which slot within the width of the module that this module reports as its slot number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000ModulePorts		1.3.6.1.4.1.50.8.1.2.1.3.5.1.1.7
The total number of ports associated with this module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000Ports		1.3.6.1.4.1.50.8.1.2.1.3.6
OBJECT IDENTIFIER

lanBlazer7000PortMgt		1.3.6.1.4.1.50.8.1.2.1.3.6.1
OBJECT IDENTIFIER

lanBlazer7000PortTable		1.3.6.1.4.1.50.8.1.2.1.3.6.1.1
A table of information related to every data port in this data networking system.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000PortEntry

lanBlazer7000PortEntry		1.3.6.1.4.1.50.8.1.2.1.3.6.1.1.1
A data port associated with this data networking system.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000PortEntry

lanBlazer7000PortIndex		1.3.6.1.4.1.50.8.1.2.1.3.6.1.1.1.1
An index that uniquely identifies this port. Typically, ports are child resources of the module that contains them. In these cases, ports are identified by their module and their relative physical position on that module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000PortName		1.3.6.1.4.1.50.8.1.2.1.3.6.1.1.1.2
The user-assigned name for this port. Note that setting this object for an internal(1) port results in an error.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..31)

lanBlazer7000PortType		1.3.6.1.4.1.50.8.1.2.1.3.6.1.1.1.3
An internal(1) port does not have an external connection. An ether-ten-oneHundred(2) port is an Ethernet port which can be switched between 10 and 100 megabits per second. An ether-oneHundred(3) port is a 100 megabits per second Fast Ethernet port. An ether-gigabit(4) port is a 1000 megabits per second Gigabit Ethernet port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	internal(1), ether-ten-oneHundred(2), ether-oneHundred(3), ether-gigabit(4)

lanBlazer7000PortBaseType		1.3.6.1.4.1.50.8.1.2.1.3.6.1.1.1.4
The base type of this port. This object may be useful to help manage new port types that are similar in nature to legacy port types.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	internal(1), ether-ten-oneHundred(2), ether-oneHundred(3), ether-gigabit(4)

lanBlazer7000PortMode		1.3.6.1.4.1.50.8.1.2.1.3.6.1.1.1.5
The mode of this port. When set to enable(1), this port passes data. When set to disable(2), the port does not receive or transmit data, nor does it generate port-level signaling e.g. link integrity pulses. Note that setting an internal(1) port to disable(2) results in an error.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000PortStatus		1.3.6.1.4.1.50.8.1.2.1.3.6.1.1.1.6
The status of this port. Disabled(1) means that this port has been disabled through management action. Okay(2) indicates that this port is operating properly. Warning(3) indicates that this port is encountering an abnormal condition that, however, allows it to continue to pass data. LinkFailure(5) means that this port is unable to pass data.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), okay(2), warning(3), disabledButOkay(4), linkFailure(5)

lanBlazer7000PortConnector		1.3.6.1.4.1.50.8.1.2.1.3.6.1.1.1.7
The connector type associated with this port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	internal(1), rj45(2), fiber-ST(3), fiber-SC(4), rs-232(5), aui(6)

lanBlazer7000PortSpeedState		1.3.6.1.4.1.50.8.1.2.1.3.6.1.1.1.8
The data rate of this port in bits per second. For example, a standard Ethernet port (e.g. 10BASE-T) would indicate a value of ten-megabits-per-second((1) indicating that the port supports a data rate of 10Mb/s. For ports that can change their data rate (e.g. 10/100 ports), the value of this object indicates the current state of the port's speed capability.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ten-megabits-per-second(1), one-hundred-megabits-per-second(2), one-gigabit-per-second(3), under-negotiation(4)

lanBlazer7000PortDuplexState		1.3.6.1.4.1.50.8.1.2.1.3.6.1.1.1.9
The value of this object indicates whether this port is operating in full- or half-duplex mode. The value under-negotiation(3) indicates that the port has not selected an operational duplex setting yet.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	half-duplex(1), full-duplex(2), under-negotiation(3)

lanBlazer7000PortGroupBinding		1.3.6.1.4.1.50.8.1.2.1.3.6.1.1.1.10
Each port is associated with a port group. Typically, a port will belong to a port group of one and the value of this object will be the same as the port index for this instance. That is, this port will point to itself. The intent of this object is to help manage ports that have hierarchical relationships. For example, an ATM port typically has a physical port and multiple logical ports (e.g. each logical port corresponding to an instance of an emulated LAN). In this case, each LANE instance would refer to the instance of the physical port associated with the ATM front-end. Another example is an FDDI DAS type port. In this case, there is a logical port associated with the FDDI switch port which is connected to the two FDDI physical port connectors. The physical FDDI ports both point to the logical instance of an FDDI port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000PortFlowControlMgt		1.3.6.1.4.1.50.8.1.2.1.3.6.2
OBJECT IDENTIFIER

lanBlazer7000PortFlowControlTable		1.3.6.1.4.1.50.8.1.2.1.3.6.2.1
A table of ports that support flow control.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000PortFlowControlEntry

lanBlazer7000PortFlowControlEntry		1.3.6.1.4.1.50.8.1.2.1.3.6.2.1.1
Configuration objects related to port based flow control.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000PortFlowControlEntry

lanBlazer7000PortFlowControlMode		1.3.6.1.4.1.50.8.1.2.1.3.6.2.1.1.21
Flow control is used to prevent or reduce the dropping of frames due to the lack of buffer space. Overall, networks are more efficient when a sending station is asked to pause in its sending process, rather than having the transmitted frames dropped. Flow control is not as efficient when used in conjunction with a shared ports, i.e. when used with a repeater. Therefore, flow control is not recommended for a port connected to shared topologies. Flow control is most effective when the port is directly connected to an end-station, especially when connected to a server. Flow control is recommended for ports connected directly to end-stations. When the port is in half-duplex mode, back pressure is used to control the incoming flow. Back pressure essentially forces collisions for short periods of time. When the port is in full-duplex mode, IEEE 802.3 standard pause frames are used to control the incoming flow. Note that setting an ether-gigabit(4) port to enable-with-aggressive-backoff(3) results in an error.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2), enable-with-aggressive-backoff(3)

lanBlazer7000PortDuplexMgt		1.3.6.1.4.1.50.8.1.2.1.3.6.3
OBJECT IDENTIFIER

lanBlazer7000PortDuplexTable		1.3.6.1.4.1.50.8.1.2.1.3.6.3.1
A table of ports that support full- and half-duplex data communications.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000PortDuplexEntry

lanBlazer7000PortDuplexEntry		1.3.6.1.4.1.50.8.1.2.1.3.6.3.1.1
A port device configuration that controls the duplex mode of this port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000PortDuplexEntry

lanBlazer7000PortDuplexMode		1.3.6.1.4.1.50.8.1.2.1.3.6.3.1.1.31
A point-to-point Ethernet port may be configured to support half or full duplex communications. A full-duplex(2) port transmits and receives data concurrently, effectively doubling the data rate of the port. Half-duplex(1) ports transmit or receive data, but not at the same time. Half-duplex ports use CSMA/CD as the access method to the network. Ports that are connected to shared segments (i.e. connected to a repeater), should always be configured to be in half-duplex mode. This object indicates the desired duplexity of this port. If auto-negotiation is turned on for this port, then this value is ignored.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	half-duplex(1), full-duplex(2)

lanBlazer7000PortSpeedMgt		1.3.6.1.4.1.50.8.1.2.1.3.6.4
OBJECT IDENTIFIER

lanBlazer7000PortSpeedTable		1.3.6.1.4.1.50.8.1.2.1.3.6.4.1
A table of port devices that support multiple speeds.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000PortSpeedEntry

lanBlazer7000PortSpeedEntry		1.3.6.1.4.1.50.8.1.2.1.3.6.4.1.1
A port that supports multiple speeds.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000PortSpeedEntry

lanBlazer7000PortSpeedMode		1.3.6.1.4.1.50.8.1.2.1.3.6.4.1.1.41
Some of these values may not be applicable to certain types of ports. This object indicates the desired data rate of this port. If auto-negotiation is turned on for this port, then this value is ignored.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ten-megabits-per-second(1), one-hundred-megabits-per-second(2)

lanBlazer7000PortAutoNegotiationMgt		1.3.6.1.4.1.50.8.1.2.1.3.6.5
OBJECT IDENTIFIER

lanBlazer7000PortAutoNegotiationTable		1.3.6.1.4.1.50.8.1.2.1.3.6.5.1
A table of ports that support auto-negotiation.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000PortAutoNegotiationEntry

lanBlazer7000PortAutoNegotiationEntry		1.3.6.1.4.1.50.8.1.2.1.3.6.5.1.1
Attributes associated with a port that supports auto-negotiation.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000PortAutoNegotiationEntry

lanBlazer7000PortAutoNegotiationMode		1.3.6.1.4.1.50.8.1.2.1.3.6.5.1.1.51
Setting this object to autoNegotiate(1) causes this port to negotiate the duplex mode and the port speed, subject to the port's capabilities.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	autoNegotiate(1), manualConfiguration(2)

lanBlazer7000PortAutoNegotiationSpeedAdvertisement		1.3.6.1.4.1.50.8.1.2.1.3.6.5.1.1.52
The speed to advertise while auto-negotiating.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ten-and-one-hundred-megabits-per-second(1), one-hundred-megabits-per-second(2), ten-megabits-per-second(3)

lanBlazer7000PortAutoNegotiationDuplexAdvertisement		1.3.6.1.4.1.50.8.1.2.1.3.6.5.1.1.53
The duplexity to advertise while auto-negotiating.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	full-and-half-duplex(1), half-duplex(2)

lanBlazer7000PortRateLimitMgt		1.3.6.1.4.1.50.8.1.2.1.3.6.6
OBJECT IDENTIFIER

lanBlazer7000PortRateLimitTable		1.3.6.1.4.1.50.8.1.2.1.3.6.6.1
A table of ports that support the ability to limit the rate of floods.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000PortRateLimitEntry

lanBlazer7000PortRateLimitEntry		1.3.6.1.4.1.50.8.1.2.1.3.6.6.1.1
The rate limit configuration associated with this port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000PortRateLimitEntry

lanBlazer7000PortRateLimitMode		1.3.6.1.4.1.50.8.1.2.1.3.6.6.1.1.61
This object configures whether rate limiting is enabled for this port (the factory default is enable(1)). Enabling rate limiting for this port prevents floods from overwhelming the output buffer associated with this port. Normally, rate limiting will only consider frames that are flooded to this port. This typically does not include known multicasts. However, known multicasts can be included in the flood limiting by setting the value of this object to enableIncludeKnownMulticast(3).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2), enableIncludeKnownMulticast(3)

lanBlazer7000PortRateLimitRate		1.3.6.1.4.1.50.8.1.2.1.3.6.6.1.1.62
The percentage of the port's transmitted data allowed to be floods (or floods and known multicasts). For example, the factory default setting of twenty-percent(4) indicates that 20% of the data rate can be floods. For 10 Mb/s ports, this is equivalent to a maximum rate of approximately 3000 flooded pps; for 100 Mb/s ports, a maximum rate of approximately 30,000 flooded pps.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	one-percent(1), two-percent(2), five-percent(3), ten-percent(4), twenty-percent(5), forty-percent(6), eighty-percent(7)

lanBlazer7000PortRateLimitBurstSize		1.3.6.1.4.1.50.8.1.2.1.3.6.6.1.1.63
The maximum number of consecutive transmitted flooded (or flooded and known multicasted) packets. Typically, the burst size is set so as to not overflow the port's buffer.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	rateLimit1(1), rateLimit2(2), rateLimit4(3), rateLimit8(4), rateLimit16(5), rateLimit32(6), rateLimit64(7), rateLimit128(8), rateLimit256(9), rateLimit1024(10), rateLimit2048(11)

lanBlazer7000PortPacePriorityMgt		1.3.6.1.4.1.50.8.1.2.1.3.6.7
OBJECT IDENTIFIER

lanBlazer7000PortPacePriorityTable		1.3.6.1.4.1.50.8.1.2.1.3.6.7.1
A table of ports that support the ability to classify frame priority based on 3Com Pace(r) Prioritization.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000PortPacePriorityEntry

lanBlazer7000PortPacePriorityEntry		1.3.6.1.4.1.50.8.1.2.1.3.6.7.1.1
A port that supports 3Com Pace(r) priority.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000PortPacePriorityEntry

lanBlazer7000PortPacePriorityMode		1.3.6.1.4.1.50.8.1.2.1.3.6.7.1.1.71
When Pace priority is enabled, this port will detect frames that use 3Com Corporation's Pace(r) Priority signaling. Frames signaled with priority in this manner are mapped to traffic priority level 4 (on scale of 0-7).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000PortCategoryMgt		1.3.6.1.4.1.50.8.1.2.1.3.6.8
OBJECT IDENTIFIER

lanBlazer7000PortCategoryTable		1.3.6.1.4.1.50.8.1.2.1.3.6.8.1
A table of ports that support the port category feature. Currently, all ports support this capability.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000PortCategoryEntry

lanBlazer7000PortCategoryEntry		1.3.6.1.4.1.50.8.1.2.1.3.6.8.1.1
A port that supports port categorization.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000PortCategoryEntry

lanBlazer7000PortCategoryMode		1.3.6.1.4.1.50.8.1.2.1.3.6.8.1.1.81
By default, all ports are considered service ports. A service port is a port that provides a networks service such as a connection to a server, other switches, or the like. A service port will trigger the service port event for status changes with the alarm severity and will trigger an alarm in the alarm table on link failure. In contrast, user ports trigger the user link event with warning severity. They do not trigger an alarm upon link failures. User ports are useful to prevent floods of traps or entries in the alarm table. This is especially true for ports connected to user hosts that power up in the morning and power down again at the end of the work day.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	userPort(1), servicePort(2)

lanBlazer7000BufferMgt		1.3.6.1.4.1.50.8.1.2.1.3.7
OBJECT IDENTIFIER

lanBlazer7000BufferTable		1.3.6.1.4.1.50.8.1.2.1.3.7.1
A table of frame buffers in the system.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000BufferEntry

lanBlazer7000BufferEntry		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1
Objects related to the management of this frame buffer.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000BufferEntry

lanBlazer7000BufferIndex		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.1
The unique index that identifies this buffer within the system. Buffers are indexed first by their module association and then a unique index within that module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000BufferFabricPort		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.2
The switch fabric port associated with this buffer.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000BufferFabricPortDirection		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.3
The value of this object indicates whether the buffer is used for buffering frames going into the switching fabric or coming out of the fabric.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	in(1), out(2)

lanBlazer7000BufferSwitchPort		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.4
The switch port associated with this frame buffer. Some buffers are not associated with any one switch port. In those cases, the value of the resource ID returned will be the null resource ID.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000BufferMemory		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.5
The amount of memory available for frame buffering in Kilobytes (KB).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000BufferAgeTimer		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.6
Configures the timer used for aging frames in this buffer. If the timer expires for a frame, the frame is dropped and the event is counted in the stale drop counter. By default, the age timer is set to a 0.25 seconds (quarter of a second). The actual time that a frame may be aged out may vary. When set to a quarter of a second (250ms), the actual time may vary between 160ms and 320ms. When set to a second (1000ms), the time may vary between 640ms and 1.28 seconds (1028ms).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), quarter-second(2), one-second(3)

lanBlazer7000BufferPriorityServicing		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.7
The value of this object configures how often the normal priority queue is serviced relative to the high priority queue. By default, the normal priority queue is serviced every thousand frames(3). This means that the normal priority queue is guaranteed to be serviced after servicing, at most, one thousand high priority frames. It is important to service the normal priority queue for two reasons. One is to prevent starvation for frames on the normal priority queue. The other reason is that frames cannot be aged if they are not serviced (see the age timer).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	strictPriority(1), everyTenThousand(2), everyThousand(3), everyHundred(4), everyFour(5)

lanBlazer7000BufferPriorityAllocation		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.8
This object controls how much of the total buffer space should be allocated to high priority queue. Please be warned that setting this object to a different value causes the associated buffer to reset, causing a short loss of data. Setting the value of this object to none(1) not only allocates the entire buffer space to normal traffic, but also has the side effect of disabling the priority threshold. In other words, all traffic will be considered as normal priority traffic.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), tenPercent(2), twentyPercent(3), thirtyPercent(4), fortyPercent(5), fiftyPercent(6)

lanBlazer7000BufferPriorityThreshold		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.9
This object configures the threshold for which frames are considered high priority. Frames may have a priority classification ranging from 0-7, 7 being the highest. By default, every frame that has priority 4 (four(5)) or above is considered a high priority frame and is buffered accordingly. If this buffer does not have any buffer space allocated for high priority frames, then the buffer threshold will be none(1). Setting this object to a different value without allocating buffer space to high priority traffic will result in an error.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), one(2), two(3), three(4), four(5), five(6), six(7), seven(8)

lanBlazer7000BufferCongestion		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.10
This object indicates whether this buffer is in a congested state..
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	informationNotAvailable(1), notCongested(2), congested(3)

lanBlazer7000BufferHighOverflowDrops		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.11
The count of the number of high priority frames dropped due to the high priority queue overflowing.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

lanBlazer7000BufferLowOverflowDrops		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.12
The count of the number of low priority frames dropped due to the low priority queue overflowing.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

lanBlazer7000BufferHighStaleDrops		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.13
The count of the number of high priority frames dropped due to being in the high priority queue too long (the frame aged out).
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

lanBlazer7000BufferLowStaleDrops		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.14
The count of the number of low priority frames dropped due to being in the low priority queue too long (the frame aged out).
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

lanBlazer7000BufferCongestionDrops		1.3.6.1.4.1.50.8.1.2.1.3.7.1.1.16
The count of the number of frames dropped due to the destination (output) buffer being congested.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

lanBlazer7000Switching		1.3.6.1.4.1.50.8.1.2.1.5
OBJECT IDENTIFIER

lanBlazer7000SwitchingLayerII		1.3.6.1.4.1.50.8.1.2.1.5.1
OBJECT IDENTIFIER

lanBlazer7000SwitchGen		1.3.6.1.4.1.50.8.1.2.1.5.1.1
OBJECT IDENTIFIER

lanBlazer7000SwitchSTPConfig		1.3.6.1.4.1.50.8.1.2.1.5.1.1.1
When set to ieee8021dStp(1), the switch executes spanning tree conformant to the IEEE 802.1D bridging standard. The switch runs one instance of spanning tree. When set to stpPerVlan(2), the switch executes a separate instance of spanning tree for each virtual LAN. This configuration conforms to the model that instances of virtual LANs within the switch are separate virtual bridging functions. This method may not work well with bridge/routers that are also running spanning tree. When set to twoLayerStp(3), the switch executes a two-layer spanning tree to prevent loops. Two layer spanning tree creates a higher 'plane' of spanning tree between VLAN devices. This method of running spanning tree is 'plug and play' with bridge/router type devices and also scales better than the other two methods for large environments. When set to disable(4), spanning tree is disabled in the switch.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ieee8021dStp(1), stpPerVlan(2), twoLayerStp(3), disable(4)

lanBlazer7000SwitchAgingTime		1.3.6.1.4.1.50.8.1.2.1.5.1.1.2
The timeout period in seconds for aging dynamically learned forwarding information. A default of 300 seconds is recommended. An aged entry is marked invalid, but is not removed from the Address Forwarding Table, because it is assumed that it will be relearned to the same location within the table.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	10..1000000

lanBlazer7000SwitchSuperAgingTime		1.3.6.1.4.1.50.8.1.2.1.5.1.1.3
The timeout period in days for removing stale invalid entries from the Address Forwarding Table. A superaged entry is removed completely from the Address Forwarding Table, because it is assumed that the entry will never be relearned.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..30

lanBlazer7000BridgeMgmt		1.3.6.1.4.1.50.8.1.2.1.5.1.2
OBJECT IDENTIFIER

lanBlazer7000BridgeTable		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1
A table of Spanning Tree information for every bridge in the system.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000BridgeEntry

lanBlazer7000BridgeEntry		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000BridgeEntry

lanBlazer7000BridgeIndex		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.1
An index that uniquely identifies this bridge.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000BridgeType		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.2
Indicates whether this is a legacy dot1d bridge consisting of all switch ports or a virtual bridge consisting of all virtual subports for a particular Vlan.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	dot1d(1), virtual(2)

lanBlazer7000BridgeMode		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.3
Used to enable or disable Spanning Tree for this bridge. When set to disable(2), all BPDUs are forwarded like regular multicast packets. The default value is enable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000BridgeStatus		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.4
The enable/disable status of this bridge. This object incorporates the setting of the lanBlazer7000SwitchSTPConfig object. When lanBlazer7000SwitchSTPConfig is set such that this bridge will not be active, lanBlazer7000BridgeStatus returns disabled(2). If lanBlazer7000SwitchSTPConfig is set such that this bridge will be active, and lanBlazer7000BridgeMode is enable(1), this object returns enabled(2).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

lanBlazer7000BridgeStpPriority		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.5
The priority value of the Bridge Identifier. See dot1dStpPriority.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

lanBlazer7000BridgeStpTimeSinceTopologyChange		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.6
The time since the last topology change was detected. See dot1dStpTimeSinceTopologyChange.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

lanBlazer7000BridgeStpTopChanges		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.7
The total number of topology changes. See dot1dStpTopChanges
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

lanBlazer7000BridgeStpDesignatedRoot		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.8
The bridge considered to be root by this node. See dot1dStpDesignatedRoot.
Status: mandatory	Access: read-only
OBJECT-TYPE
	BridgeId

lanBlazer7000BridgeStpRootCost		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.9
The cost of the path to the root from this node. See dot1dStpRootCost.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000BridgeStpRootPort		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.10
The port number with the lowest cost path to the root bridge. See dot1dStpRootPort.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000BridgeStpMaxAge		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.11
The maximum age used by this bridge to hold onto STP information before discarding. See dot1dStpMaxAge.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Timeout

lanBlazer7000BridgeStpHelloTime		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.12
The amount of time between configuration BPDUs. See dot1dStpHelloTime.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Timeout

lanBlazer7000BridgeStpHoldTime		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.13
The time value that indicates the interval during which no more than two configuration BPDUs will be sent by this node. See dot1dStpHoldTime.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000BridgeStpForwardDelay		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.14
The amount of time that this node stays in each of the Listening and Learning states. See dot1dStpForwardDelay.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Timeout

lanBlazer7000BridgeStpBridgeMaxAge		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.15
The value of MaxAge when this bridge is the root. See dot1dStpBridgeMaxAge.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Timeout	600..4000

lanBlazer7000BridgeStpBridgeHelloTime		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.16
The value of HelloTime to use when this bridge is the root. See dot1dStpBridgeHelloTime.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Timeout	100..1000

lanBlazer7000BridgeStpBridgeForwardDelay		1.3.6.1.4.1.50.8.1.2.1.5.1.2.1.1.17
The value of FowardDelay to use when this bridge is the root. See dot1dStpBridgeForwardDelay.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Timeout	400..3000

lanBlazer7000BridgePortMgmt		1.3.6.1.4.1.50.8.1.2.1.5.1.3
OBJECT IDENTIFIER

lanBlazer7000BridgePortTable		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1
A table of Spanning Tree information for every port that supports Spanning Tree in every bridge in the system
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000BridgePortEntry

lanBlazer7000BridgePortEntry		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000BridgePortEntry

lanBlazer7000BridgePortIndex		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1.1.1
An index that uniquely identifies this bridge port. This index corresponds to the lanBlazer7000ResourceIndex for bridge port type resources.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000BridgePortPriority		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1.1.2
The value of the priority field in the port ID. See dot1dStpPortPriority. The default value is 128.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

lanBlazer7000BridgePortState		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1.1.3
The port's current state as defined by the Spanning Tree Protocol. See dot1dStpPortState. The virtual port is considered broken if its switch port is blocked.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)

lanBlazer7000BridgePortEnable		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1.1.4
The enabled/disabled status of this port. See dot1dStpPortEnable. The default is enabled(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

lanBlazer7000BridgePortPathCost		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1.1.5
The contribution of this port to the path cost of the paths towards the spanning tree root. See dot1dStpPortPathCost. The default value is dependent on the port speed, trunking mode, and duplexity.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

lanBlazer7000BridgePortDesignatedRoot		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1.1.6
The bridge recorded as root for this port's segment. See dot1dStpPortDesignatedRoot.
Status: mandatory	Access: read-only
OBJECT-TYPE
	BridgeId

lanBlazer7000BridgePortDesignatedCost		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1.1.7
The path cost of the designated root of the segment connected to this port. See dot1dStpPortDesignatedCost.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000BridgePortDesignatedBridge		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1.1.8
The bridge identifier of the bridge that is considered the designated bridge for this port's segment. See dot1dStpPortDesignatedBridge.
Status: mandatory	Access: read-only
OBJECT-TYPE
	BridgeId

lanBlazer7000BridgePortDesignatedPort		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1.1.9
The port identifier of the port on the Designated Bridge for this port's segment. See dot1dStpPortDesignatedPort.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(2)

lanBlazer7000BridgePortForwardTransitions		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1.1.10
The number of times this port has transitioned from the learning state to the forwarding state. See dot1dStpPortForwardTransitions.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

lanBlazer7000BridgePortFastStart		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1.1.11
This object is being replaced by the switch port object lanBlazer7000SwitchPortFastStart. When this bridge port object is set to enable(1), the bridge port and all other bridge ports on the same switch port, transition right from blocking to forwarding, skipping the listening and learning states. When this bridge port object is set to disable(2), the bridge port and all other bridge ports on the same switch port have this option disabled. The user should be warned that using the fast start feature greatly increases the likelihood of unintended network loops that would otherwise be prevented by participating in the normal spanning tree algorithm. The factory default value for this object is disable(2).
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000BridgePortSetDefault		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1.1.12
When set to setDefault(2), the lanBlazer7000BridgePortPriority, lanBlazer7000BridgePortEnable, and lanBlazer7000BridgePortPathCost will be set to the factory default values.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	useCurrentValues(1), setDefault(2)

lanBlazer7000BridgePortEnableChangeDetection		1.3.6.1.4.1.50.8.1.2.1.5.1.3.1.1.13
When this object is set to enable(1), a Topology Change Notification will be generated when this port goes to Blocking or Forwarding (if the port is a designated port). When set to disable(2), no Topology Change Notification will be generated for this port. The default is enable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000L2AddrMgmt		1.3.6.1.4.1.50.8.1.2.1.5.1.4
OBJECT IDENTIFIER

lanBlazer7000L2AddrDatabaseMgt		1.3.6.1.4.1.50.8.1.2.1.5.1.4.1
OBJECT IDENTIFIER

lanBlazer7000L2AddressTable		1.3.6.1.4.1.50.8.1.2.1.5.1.4.1.1
A table of address table entries. The address table is used by the bridging function to perform forwarding and filtering decisions. An address may appear multiple times in different entries corresponding to the different logical address tables.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000L2AddressEntry

lanBlazer7000L2AddressEntry		1.3.6.1.4.1.50.8.1.2.1.5.1.4.1.1.1
A particular address table entry.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000L2AddressEntry

lanBlazer7000L2AddressIndex		1.3.6.1.4.1.50.8.1.2.1.5.1.4.1.1.1.1
An index that uniquely identifies this address entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000L2AddressTableIndex		1.3.6.1.4.1.50.8.1.2.1.5.1.4.1.1.1.2
The address table that this entry is associated with.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000L2AddressMacAddress		1.3.6.1.4.1.50.8.1.2.1.5.1.4.1.1.1.3
The IEEE 802 MAC Address associated with this database entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

lanBlazer7000L2AddressPortBinding		1.3.6.1.4.1.50.8.1.2.1.5.1.4.1.1.1.4
The switch port that this address is associated with.
Status: mandatory	Access: read-write
OBJECT-TYPE
	ResourceId

lanBlazer7000L2AddressBindingValid		1.3.6.1.4.1.50.8.1.2.1.5.1.4.1.1.1.5
The port binding of an address entry is aged out in conformance with the specifications laid out in the IEEE 802.1D standard. When the address is aged out, the port binding becomes invalid.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	valid(1), invalid(2)

lanBlazer7000L2AddressVlanID		1.3.6.1.4.1.50.8.1.2.1.5.1.4.1.1.1.6
The VLAN ID of the VLAN that this address entry corresponds to.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000L2AddressPriority		1.3.6.1.4.1.50.8.1.2.1.5.1.4.1.1.1.7
If set to high(2), frames destined to this address are classified with priority value 4.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	priorityZero(1), priorityFour(2)

lanBlazer7000L2AddressForward		1.3.6.1.4.1.50.8.1.2.1.5.1.4.1.1.1.8
When set to specialDelivery(2), frames sent to this address are treated to special delivery where the spanning tree state of the inbound port is ignored. Typically, special delivery is only used for Bridge PDUs such as spanning tree frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	normalForward(1), specialDelivery(2)

lanBlazer7000L2AddressCopy		1.3.6.1.4.1.50.8.1.2.1.5.1.4.1.1.1.9
It is sometimes useful for the switch processor to eavesdrop on traffic to certain destinations. This is especially useful in supporting the intelligent multicasting function.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	normalForward(1), copyCPU(2)

lanBlazer7000L2AddressPersistence		1.3.6.1.4.1.50.8.1.2.1.5.1.4.1.1.1.10
This object indicates the persistence of this entry: other(1) - This entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - Writing this value to the object removes the corresponding entry. permanent(3) - Address is not aged out. Additionally, if the address is seen as a source on a different port for this VLAN, the frame is filtered and the filter event is counted. Static address entries are stored in non-volatile memory and are restored to the address table following each system reset. deleteOnReset(4) - Indicates that the entry is not aged out, however the entry is not stored in non-volatile memory. Therefore, when the device is reset, the entry will not be restored. deleteOnTimeout(5) - Typically, address entries are learned dynamically by the switch. These entries are aged out of the table if they are not active on the network. This value correlates to this state.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), invalid(2), permanent(3), deleteOnReset(4), deleteOnTimeout(5)

lanBlazer7000L2AddressStatus		1.3.6.1.4.1.50.8.1.2.1.5.1.4.1.1.1.11
This object indicates the status of the entry: other(1) - None of the following. learned(2) - This entry was learned dynamically. self(3) - The value of the corresponding instance of lanBlazer7000AddressMacAddress represents one of the bridge's addresses. mgmt(4) - This entry was added or modified by management. Entries that have been added by management and made permanent
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), learned(2), self(3), mgmt(4)

lanBlazer7000L2AddrSummaryMgt		1.3.6.1.4.1.50.8.1.2.1.5.1.4.2
OBJECT IDENTIFIER

lanBlazer7000L2AddrSummaryTable		1.3.6.1.4.1.50.8.1.2.1.5.1.4.2.1
This summary table packs the address entries in the address database into summary objects. The goal is to optimize the upload of the large amount of data stored therein. Typically, a management station would use getNext requests to retrieve the next logical summary object. The returned object value contains the next n entries of the address database packed into one PDU. The instance of the object returned is the index of the last address entry packed in the summary, thereby optimizing for the next getNext request. [ Fix this? What about gets?]
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000L2AddrSummaryEntry

lanBlazer7000L2AddrSummaryEntry		1.3.6.1.4.1.50.8.1.2.1.5.1.4.2.1.1
A summary object that packs as many address entries possible into a summary object.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000L2AddrSummaryEntry

lanBlazer7000L2AddrSummary		1.3.6.1.4.1.50.8.1.2.1.5.1.4.2.1.1.1
The value of this object is a packed opaque structure representing an array of address entries. The format of this structure is: struct L2AddressEntry { UNS32 index; UNS8 addr[6]; // mac address UNS8 fabricPort; //fabricPort and subPort == lanBlazer7000L2AddressPortBinding UNS8 subPort; UNS16 vlanID, //the global vlan id UNS8 portBindingValidFlag; UNS8 addressForwardFlag; UNS8 addressCopyFlag; UNS8 addressPersistence; UNS8 addressStatus; }; struct L2AddressSummary{ UNS8 numberOfEntries; // Number of entries that follow UNS8 version; // version == 1 UNS16 endianFlag; L2AddressEntry entryArray[numberOfEntries]; };
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(20..4096)

lanBlazer7000L2AddrControlMgt		1.3.6.1.4.1.50.8.1.2.1.5.1.4.3
OBJECT IDENTIFIER

lanBlazer7000L2AddressControlTable		1.3.6.1.4.1.50.8.1.2.1.5.1.4.3.1
This table provides the network manager the ability to create new, static address entries. Entries added through this table are added to the specified address table as a static entry and are save in non-volatile memory for reconfiguration upon system restart. This table is indexed by the lanBlazer7000AgentMgrIndex value which provides a separate instance for each manager.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000L2AddressControlEntry

lanBlazer7000L2AddressControlEntry		1.3.6.1.4.1.50.8.1.2.1.5.1.4.3.1.1
A control entry enables this manager to add a new entry to the specified address table. When the entry is written to, the control index value is reset to 0. When the actual entry is created, the index value will read as non-zero, reporting the actual entry created.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000L2AddressControlEntry

lanBlazer7000L2AddressControlIndex		1.3.6.1.4.1.50.8.1.2.1.5.1.4.3.1.1.1
The index of the address entry that was created for this address.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000L2AddressControlMacAddress		1.3.6.1.4.1.50.8.1.2.1.5.1.4.3.1.1.2
The IEEE 802 MAC Address associated with this database entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	MacAddress

lanBlazer7000L2AddressControlPortBinding		1.3.6.1.4.1.50.8.1.2.1.5.1.4.3.1.1.3
The port to bind this address to.
Status: mandatory	Access: read-write
OBJECT-TYPE
	ResourceId

lanBlazer7000L2AddressControlVlanID		1.3.6.1.4.1.50.8.1.2.1.5.1.4.3.1.1.4
The VLAN ID of the VLAN to bind this address to.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

lanBlazer7000L2AddressControlPriority		1.3.6.1.4.1.50.8.1.2.1.5.1.4.3.1.1.5
If set to high(2), frames destined to this address are classified with priority value 4.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	priorityZero(1), priorityFour(2)

lanBlazer7000L2AddressControlPersistence		1.3.6.1.4.1.50.8.1.2.1.5.1.4.3.1.1.6
The persistence of the entry to be created: permanent(1) - Address is not aged out. Additionally, if the address is seen as a source on a different port for this VLAN, the frame is filtered and the filter event is counted. Static address entries are stored in non-volatile memory and are restored to the address table following each system reset. deleteOnReset(2) - Indicates that the entry is not to be aged, however the entry is not stored in non-volatile memory. Therefore, when the device is reset, the entry will not be restored. deleteOnTimeout(3) - Indicates that the entry is to be aged by the normal aging process.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	permanent(1), deleteOnReset(2), deleteOnTimeout(3)

lanBlazer7000L2AddressControlStatus		1.3.6.1.4.1.50.8.1.2.1.5.1.4.3.1.1.7
The status of an entry to be created. When adding an entry all fields will be set, and then the control status is set to createRequest(1), indicating that the entry is to be created. During creation, the status will be underCreation(2). If the creation is successful, then the status will be set to success(3), and the value of lanBlazer7000AddressControlIndex indicates the index of the entry that was created in the address table. Otherwise if the creation was not successful, then one of the following error codes will be set and the entry will not be created: otherError(4) - An error other then the others defined. entryExistsError(5) - An entry already exists with this MAC address in this address table. invalidMacAddress(6) - Cannot create an entry with this MAC address. invalidTableIndex(7) - The table does not exist. invalidPortBinding(8) - The port binding is invalid. invalidVlanID(9) - The VLAN ID is invalid. Note that the only value that is valid to write to this object is createRequest(1), and that this object will never return the value createRequest(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	createRequest(1), underCreation(2), success(3), otherError(4), entryExistsError(5), invalidMacAddress(6), invalidPortBinding(7), invalidVlanID(8)

lanBlazer7000L2AddrChangeMgt		1.3.6.1.4.1.50.8.1.2.1.5.1.4.4
OBJECT IDENTIFIER

lanBlazer7000L2AddressChangeLast		1.3.6.1.4.1.50.8.1.2.1.5.1.4.4.1
The index of the last entry written to the address change table
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000L2AddressChangeWraps		1.3.6.1.4.1.50.8.1.2.1.5.1.4.4.2
The count of the number of times the address change table has wrapped.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

lanBlazer7000L2AddressChangeMaxEntries		1.3.6.1.4.1.50.8.1.2.1.5.1.4.4.3
The maximum number of entries in the address change table.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1024..4096

lanBlazer7000L2AddressChangeTable		1.3.6.1.4.1.50.8.1.2.1.5.1.4.4.4
.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000L2AddressChangeEntry

lanBlazer7000L2AddressChangeEntry		1.3.6.1.4.1.50.8.1.2.1.5.1.4.4.4.1
The address change table provides a quick way of getting only the entries that have recently changed. Since entries age out as part of the normal switching process, entries that have aged (i.e. their destination bindings are no longer valid) are not considered to be changed. Any other modification to the entry, including deletion or creation, are considered to be changes. The address change table is considered a circular table. When an entry changes, it is added to the next position within the table. If the 'next' position goes beyond the end of the table, the 'next' position is set to the beginning of the table (1) and the wrap counter (lanBlazer7000AddressChangeWraps) is incremented. The lanBlazer7000AddressChangeLast value is updated with the index of the last entered entry. An entry may be in the table multiple times if it has changed multiple times. Every time that an entry changes, it is added to the change table. A network management application should follow the following algorithm when polling this table: 1. Set lastChangeWrap = lanBlazer7000AddressChangeWraps. 2. Set lastChangeIndex = lanBlazer7000AddressChangeLast 3. Get the entire lanBlazer7000AddressEntryTable. 4. Submit a getNext for ., updating lastChangeWrap and lastChangeIndex with the returned next values. Update the address entry database with the changed values. 5. Repeat step 4 until no more entries are returned. 6. Wait polling timeout period. 7. Get wrap events counter and last index. If the wrap events counter is equal to lastChangeWrap, then goto step 4. Else if the wrap events counter is more then one greater then lastChangeWrap, goto step 1. Else the wrap events counter is exactly one greater then lastChangeWrap, and if the last index is greater then lastChangeIndex, then goto step 1, else goto step 4. The last step simply insures that we have not missed any of the change entries. Essentially it says that if we have wrapped to beyond where we last polled, then we must get the entire table to synch up again. Otherwise we can just get the entries that have changed.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000L2AddressChangeEntry

lanBlazer7000L2AddressChangeWrapCount		1.3.6.1.4.1.50.8.1.2.1.5.1.4.4.4.1.1
The number of times that the lanBlazer7000AddressChangeLastIndex had wrapped when this entry was added.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000L2AddressChangeIndex		1.3.6.1.4.1.50.8.1.2.1.5.1.4.4.4.1.2
The index that uniquely identifies this address change entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000L2AddressChangeIndexChanged		1.3.6.1.4.1.50.8.1.2.1.5.1.4.4.4.1.3
The address entry that changed. The value of this object corresponds to the lanBlazer7000L2AddressIndex object.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000L2AddressChangeSummary		1.3.6.1.4.1.50.8.1.2.1.5.1.4.4.4.1.4
The structure is interpreted in the following manner:
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(20)

lanBlazer7000SwitchPortMgt		1.3.6.1.4.1.50.8.1.2.1.5.2
OBJECT IDENTIFIER

lanBlazer7000SwitchPortTable		1.3.6.1.4.1.50.8.1.2.1.5.2.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000SwitchPortEntry

lanBlazer7000SwitchPortEntry		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000SwitchPortEntry

lanBlazer7000SwitchPortIndex		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.1
A unique index that identifies this switch port. The value of this index corresponds to the value of the lanBlazer7000ResourceIndex for switch ports.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000SwitchPortSTAPMode		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.2
Disabling spanning tree on a switch port prevents the switch port from participating in the spanning tree process. When disabled(2), this port will neither generate BPDUs, nor process received BPDUs. Also, the port will always start in the forwarding state. A port configured in this mode will not be able to detect network loops involving this port. The factory default is to enable spanning tree on all ports.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000SwitchPortConvertToStatic		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.3
When this object is set to convertToStatic(2), all addresses learned on this port will be added to the non-volatile version of the static address table. Typically, this object will be used to perform a crude form of address database update where the address activity associated with this port is collected as static (i.e. permanent) addresses while the value of this object is set to convertToStatic(2). Following this usually short period of time (perhaps a week of activity), the value of this object is restored back to its default value of learnAsDynamic(1) and learning for this port is disabled. It is important that the user verify the address database to verify that only the desired addresses were made permanent.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	learnAsDynamic(1), convertToStatic(2)

lanBlazer7000SwitchPortLearningMode		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.4
Disable learning on a bridge port to prevent new addresses from being added to the address database. Used in combination with static (permanent) address entries, disabling address learning is an effective security feature to prevent new hosts from appearing on the network, or to prevent hosts from moving to different locations in the network. The default is enable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000SwitchPortHuntGroup		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.5
Hunt groups provide the capability to logically bind multiple switch ports into one switch port. This provides a way of balancing the load of multiple links between like-configured switches. Care must be taken to configure the hunt groups properly to prevent accidental network looping. Use this object to bind this port to a specific hunt group. When not configured to a specific hunt group, set the value of this object to zero.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

lanBlazer7000SwitchPortPhysicalPort		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.6
The physical port resource bound to this switch port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000SwitchPortKnownMode		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.7
Enabling known mode for this switch port causes the port to safely discard frames flooded because they are unknown unicast frames. This mode greatly enhances the efficiency of the port's output buffer since space is not wasted for frames not meant for this port. Enabling this feature disables learning for this port. Addresses associated for this port should be entered statically. The default is disable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000SwitchPortMappingMethod		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.8
The frame mapping method of this switch port. When set to port-based(1) (the factory default), all non-tagged frames are classified to the VLAN associated with this switch port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	port-based(1)

lanBlazer7000SwitchPortTrunkingMode		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.9
The trunking mode of this port. All frames transmitted out this switch port are translated to the appropriate trunking format: Clear: Ethernet or IEEE 802.3 frame format. This is the default. IEEE 802.1Q: The original frame with a new Ethernet Type (Protocol = 0xXXXX) and the VLAN ID inserted following the original Source Address. Also, the CRC is recalculated. Multi-level: The original frame is encapsulated in an IEEE 802.3 legal frame proprietary to a major networking equipment vendor. 3Com LinkSwitch: The original frame has the VLAN ID added to the front of the frame (before the Destination Address). Trunking format is proprietary to 3Com Corporation.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1), ieee8021q(2), multiLevel(3), trunk3Com(4)

lanBlazer7000SwitchPortVlanBindingMethod		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.10
The VLAN binding method of a switch port specifies the way in which the port can be a member of the egress lists of VLANs other than the port default VLAN specified by lanBlazer7000SwitchPortVlanID: static: A Virtual Switch Port must be statically created for each VLAN/port combination. persistent: A Virtual Switch Port is automatically created for each VLAN known to the switch (i.e., the port is a member of the egress lists of all VLANs). dynamic: A Virtual Switch Port is automatically created for each VLAN when the associated VLAN ID is used as a tag in an IEEE 802.1Q or Multi-level tagged frame received on the port (i.e., the port is a member of the egress lists of the VLANs from frames received on the port). The default is static.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	static(1), persistent(2), dynamic(3)

lanBlazer7000SwitchPortIgnoreTag		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.11
Each switch port is capable of ignoring the VLAN Tag associated with a frame in a trunking format. When ignored, the tag is used as the default in the event that a VLAN classification based on the switch's policy(s) cannot be made. This feature is useful for connecting layer 2 VLANs and layer 3 VLANs. The default is useTag.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	useTag(1), ignoreTag(2)

lanBlazer7000SwitchPortVlanID		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.12
When this switch port is configured in port-based VLAN mode, all non-tagged frames received on this port are bound to this VLAN. Otherwise, non-tagged frames are classified to this VLAN as the default if a VLAN binding cannot be otherwise determined. The factory default is 1, which is the VLAN ID of the Default VLAN.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

lanBlazer7000SwitchPort3ComMappingTableIndex		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.13
The 3Com VLAN mapping table associated with this switch port. The default is 1, which indicates the default mapping table.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

lanBlazer7000SwitchPortAutoVlanCreation		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.14
Enabling auto VLAN creation for this switch port causes the port to dynamically create a VLAN whenever an IEEE 802.1Q or Multi-level tagged frame is received on the port with a tag value which does not correspond to a known VLAN. All switch ports with a trunking mode of IEEE 802.1Q or Multi-level are bound to this created VLAN. The default is disable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000SwitchPortMirrorMode		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.15
When set to enable(1), this object indicates that the port is defined as a mirror port through the lanBlazer7000PortMirroringTable. A mirror port duplicates frames received at one or more source ports.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000SwitchPortIfIndex		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.16
Each switch port is associated with an interface. This object provides a mechanism to map switch ports to bridge ports.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000SwitchPortFastStart		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.17
When this object is set to enable(1), bridge ports on this switch port transitions right from blocking to forwarding, skipping the listening and learning states. The user should be warned that using the fast start feature greatly increases the likelihood of unintended network loops that would otherwise be prevented by participating in the normal spanning tree algorithm. The factory default value for this object is disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000SwitchPortVlanExchange		1.3.6.1.4.1.50.8.1.2.1.5.2.1.1.18
When this object is set to enable(1), this switch port attempts to learn VLANs from a major networking equipment vendor if the switch port's trunking mode is IEEE 802.1Q Format or Multi-level Format. The factory default value for this object is enable(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000HuntGroupMgt		1.3.6.1.4.1.50.8.1.2.1.5.4
OBJECT IDENTIFIER

lanBlazer7000HuntGroupTable		1.3.6.1.4.1.50.8.1.2.1.5.4.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000HuntGroupEntry

lanBlazer7000HuntGroupEntry		1.3.6.1.4.1.50.8.1.2.1.5.4.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000HuntGroupEntry

lanBlazer7000HuntGroupIndex		1.3.6.1.4.1.50.8.1.2.1.5.4.1.1.1
An index that uniquely identifies this hunt group. This index corresponds to the value of lanBlazer7000ResourceIndex for resources of the hunt group type.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000HuntGroupName		1.3.6.1.4.1.50.8.1.2.1.5.4.1.1.2
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

lanBlazer7000HuntGroupBasePort		1.3.6.1.4.1.50.8.1.2.1.5.4.1.1.3
The switch port index that serves as the base port for this hunt group. Each hunt group requires a base port. In lieu of a specific configuration, the hunt group will inherit the first switch port bound to the hunt group as its base port. The base port serves as the management focus for the hunt group. That is, a hunt group is managed as one switch port whose instance is provided by the base switch port. All configuration (e.g. spanning tree information) and statistics related to switch ports are meaningful only through the instance of the base port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000HuntGroupNumberOfPorts		1.3.6.1.4.1.50.8.1.2.1.5.4.1.1.4
The current number of ports that belong to this hunt group.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000HuntGroupLoadSharing		1.3.6.1.4.1.50.8.1.2.1.5.4.1.1.5
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000HuntGroupStatus		1.3.6.1.4.1.50.8.1.2.1.5.4.1.1.6
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	createRequest(1), underCreation(2), deleteRequest(3), active(4)

lanBlazer7000PortMirroringMgt		1.3.6.1.4.1.50.8.1.2.1.5.5
OBJECT IDENTIFIER

lanBlazer7000PortMirroringTable		1.3.6.1.4.1.50.8.1.2.1.5.5.1
A table of port mirroring entries used to mirror traffic from a source port to a mirror port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000PortMirroringEntry

lanBlazer7000PortMirroringEntry		1.3.6.1.4.1.50.8.1.2.1.5.5.1.1
Objects related to the PortMirroring functionality.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000PortMirroringEntry

lanBlazer7000PortMirroringIndex		1.3.6.1.4.1.50.8.1.2.1.5.5.1.1.1
The unique index that identifies this entry. This index consists of a switch fabric port and the index of a Packet Lookup Engine servicing this fabric port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000PortMirroringSourceSubPort		1.3.6.1.4.1.50.8.1.2.1.5.5.1.1.2
The frame sampler source switch subport. The source port is the port from which received traffic will be mirrored. This object identifies the switch subport only, the switch fabric port is identified in lanBlazer7000PortMirroringIndex. If set to 0, all subports associated with the lanBlazer7000PortMirroringIndex will be source ports. The default value is 0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

lanBlazer7000PortMirroringSamplerType		1.3.6.1.4.1.50.8.1.2.1.5.5.1.1.3
The type for this frame sampler. When set to enable(1), every frame received on the source port(s) will be mirrored at the mirror port. When set to disable(2), no frames received on the source port(s) will be mirrored at the mirror port. When set to periodic(3), frames will be mirrored at the rate defined in lanBlazer7000PortMirroringRate. The default value is disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2), periodic(3)

lanBlazer7000PortMirroringRate		1.3.6.1.4.1.50.8.1.2.1.5.5.1.1.4
Used in conjunction with lanBlazer7000PortMirroringSamplerType to implement periodic sampling functionality. If lanBlazer7000PortMirroringSamplerType is set to periodic(3), this object defines the number of packets/second that will be mirrored. If lanBlazer7000PortMirroringSamplerType is not periodic(3), this object will set to 0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

lanBlazer7000PortMirroringMirrorPort		1.3.6.1.4.1.50.8.1.2.1.5.5.1.1.5
The Switch Port on which frames received at source ports(s) will be duplicated. If no mirror port has been defined this object will return NULL.
Status: mandatory	Access: read-write
OBJECT-TYPE
	ResourceId

lanBlazer7000VlanMgt		1.3.6.1.4.1.50.8.1.2.1.7
OBJECT IDENTIFIER

lanBlazer7000Vlans		1.3.6.1.4.1.50.8.1.2.1.7.1
OBJECT IDENTIFIER

lanBlazer7000VlanTable		1.3.6.1.4.1.50.8.1.2.1.7.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000VlanEntry

lanBlazer7000VlanEntry		1.3.6.1.4.1.50.8.1.2.1.7.1.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000VlanEntry

lanBlazer7000VlanID		1.3.6.1.4.1.50.8.1.2.1.7.1.1.1.1
An identifier that is unique within the administrative domain. This ID is assigned by the management application and is meaningful within that context. This ID is used to identify VLANs when tagged using either the IEEE 802.1 frame format or the Multi-level frame format.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000VlanName		1.3.6.1.4.1.50.8.1.2.1.7.1.1.1.2
A user-assignable name for this Vlan.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..31)

lanBlazer7000VlanIfIndex		1.3.6.1.4.1.50.8.1.2.1.7.1.1.1.3
Each virtual LAN has a virtual interface associated with it. This enables RMON monitoring to occur per-VLAN. It also provides a handy mechanism to map virtual LANs to bridge ports by mapping them with the ifStack table from the Interface MIB.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000VlanAFTIndex		1.3.6.1.4.1.50.8.1.2.1.7.1.1.1.4
The address table used for this VLAN for explicitly tagged frames (frames received in a trunking frame format or from a port in port-based VLAN mode.) Normally, each VLAN maps to a unique address table. This is useful for environments with duplicate host addresses appear on different VLANs on different ports. For those environments where duplicate hosts on different VLANs don't exist, or exist but are on the same port, and where the address table size and/or aging is a concern, then multiple VLANs may be mapped to the same address table.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

lanBlazer7000VlanBridgeIndex		1.3.6.1.4.1.50.8.1.2.1.7.1.1.1.5
The bridge resource which is bound to this Vlan.
Status: mandatory	Access: read-write
OBJECT-TYPE
	ResourceId

lanBlazer7000VlanStatus		1.3.6.1.4.1.50.8.1.2.1.7.1.1.1.6
The status of an entry to be created or deleted. When adding an entry all fields will be set, and then the status is set to createRequest(1) (indicating that the entry is to be created). When deleting an entry the status is set to destroyRequest(3) (indicating that the entry is to be destroyed). During creation the status will be underCreation(2). If the creation is successful, then the status will be set to active(5). Otherwise if the creation was not successful then one of the following error codes will be set and the entry will not be created: otherError(6) - An error other than the others defined. entryExistsError(7) - An entry already exists. invalidVlanID(8) - the VLAN ID is invalid. invalidVlanName(9) - the VLAN name is invalid. invalidVlanAFTIndex(10) - the VLAN AFT index is invalid. invalidVlanBridgeIndex(11) - the VLAN bridge index is invalid. invalidVlanInitialHashTableSize(12) - the VLAN initial hash table size is invalid. invalidVlanAutoIncrementHTSize(13) - the VLAN auto increment hash table size is invalid.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	createRequest(1), underCreation(2), destroyRequest(3), underDestruction(4), active(5), otherError(6), entryExistsError(7), invalidVlanID(8), invalidVlanName(9), invalidVlanAFTIndex(10), invalidVlanBridgeIndex(11), invalidVlanInitialHashTableSize(12), invalidVlanAutoIncrementHTSize(13)

lanBlazer7000VlanInitialHashTableSize		1.3.6.1.4.1.50.8.1.2.1.7.1.1.1.7
The initial hash table size used for MAC addresses on this VLAN. This attribute may only be set when lanBlazer7000VlanStatus is set to createRequest(1). It must be a power of 2 between 16 and 8192, inclusive.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	16..8192

lanBlazer7000VlanAutoIncrementHTSize		1.3.6.1.4.1.50.8.1.2.1.7.1.1.1.8
This attribute specifies whether or not the hash table size used for MAC addresses on this VLAN is automatically increased as necessary to hold more MAC addresses. This attribute may only be set when lanBlazer7000VlanStatus is set to createRequest(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	true(1), false(2)

lanBlazer7000VlanLearnStatus		1.3.6.1.4.1.50.8.1.2.1.7.1.1.1.9
This attribute indicates if the VLAN was learned. If learned it indicates if the VLAN was learned either by VLAN Exchange or Auto VLAN creation.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notLearned(1), vlanExchange(2), auto(3)

lanBlazer7000VlanMappings		1.3.6.1.4.1.50.8.1.2.1.7.3
OBJECT IDENTIFIER

lanBlazer70003ComMapping		1.3.6.1.4.1.50.8.1.2.1.7.3.1
OBJECT IDENTIFIER

lanBlazer70003ComMappingTable		1.3.6.1.4.1.50.8.1.2.1.7.3.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer70003ComMappingEntry

lanBlazer70003ComMappingEntry		1.3.6.1.4.1.50.8.1.2.1.7.3.1.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer70003ComMappingEntry

lanBlazer70003ComMappingTableIndex		1.3.6.1.4.1.50.8.1.2.1.7.3.1.1.1.1
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer70003ComMappingTableName		1.3.6.1.4.1.50.8.1.2.1.7.3.1.1.1.2
A user-readable name associated with this table.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..31)

lanBlazer70003ComMappingTableStatus		1.3.6.1.4.1.50.8.1.2.1.7.3.1.1.1.3
The status of an entry to be created. When adding an entry all fields will be set, and then the status is set to createRequest(1), indicating that the entry is to be created. If the creation is successful, then the status will be set to active(3). Otherwise if the creation was not successful then one of the following error codes will be set and the entry will not be created: entryExistsError(4) - An entry already exists. otherError(5) - An error other than the others defined.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	createRequest(1), destroyRequest(2), active(3), entryExistsError(4), otherError(5)

lanBlazer7000Vlan3ComMapping		1.3.6.1.4.1.50.8.1.2.1.7.3.2
OBJECT IDENTIFIER

lanBlazer7000Vlan3ComMappingTable		1.3.6.1.4.1.50.8.1.2.1.7.3.2.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000Vlan3ComMappingEntry

lanBlazer7000Vlan3ComMappingEntry		1.3.6.1.4.1.50.8.1.2.1.7.3.2.1.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000Vlan3ComMappingEntry

lanBlazer7000Vlan3ComMappingIndex		1.3.6.1.4.1.50.8.1.2.1.7.3.2.1.1.1
The external tag of this 3Com VLAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..16

lanBlazer7000Vlan3ComMappingVlanID		1.3.6.1.4.1.50.8.1.2.1.7.3.2.1.1.2
The VLAN ID of the VLAN that this 3Com tag is associated with.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

lanBlazer7000Vlan3ComMappingStatus		1.3.6.1.4.1.50.8.1.2.1.7.3.2.1.1.3
The status of an entry to be created. When adding an entry all fields will be set, and then the status is set to createRequest(1), indicating that the entry is to be created. If the creation is successful, then the status will be set to active(3). Otherwise if the creation was not successful then one of the following error codes will be set and the entry will not be created: otherError(4) - An error other than the others defined.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	createRequest(1), destroyRequest(2), active(3), otherError(4)

lanBlazer7000VirtualPorts		1.3.6.1.4.1.50.8.1.2.1.7.4
OBJECT IDENTIFIER

lanBlazer7000VirtualSwitchPortTable		1.3.6.1.4.1.50.8.1.2.1.7.4.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000VirtualSwitchPortEntry

lanBlazer7000VirtualSwitchPortEntry		1.3.6.1.4.1.50.8.1.2.1.7.4.1.1
An instance of a virtual switch port indicates that this switch port is a member of this VLAN.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000VirtualSwitchPortEntry

lanBlazer7000VirtualSwitchPortIndex		1.3.6.1.4.1.50.8.1.2.1.7.4.1.1.1
The Resource ID of the virtual switch port bound to the VLAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000VirtualSwitchPortFormat		1.3.6.1.4.1.50.8.1.2.1.7.4.1.1.2
Typically, a VLAN capable switch port has one of three modes: access, trunk, or hybrid. In access mode, the port sends frames in clear format (untagged). In trunk mode, all outbound frames are translated into the switch port's configured trunking format. In hybrid mode, it is possible for a port to send trunked frames for some VLANs and clear frames for others. In this case, the switch port is configured to trunk, and the virtual switch port(s) for those VLANs that require clear formatted frames are configured to be override the switch port setting. This is done by setting this object to clear(1). By default, the value of this object is trunkingFormat(2) which means to use the trunking format configured for this switch port. (which may be clear).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1), trunkingFormat(2)

lanBlazer7000VirtualSwitchPortBridgePort		1.3.6.1.4.1.50.8.1.2.1.7.4.1.1.3
The bridge port resource bound to this virtual port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	ResourceId

lanBlazer7000VirtualSwitchPortBindingType		1.3.6.1.4.1.50.8.1.2.1.7.4.1.1.4
The method by which this switch port was bound to the VLAN. If the value is static(1), the binding was manually created by the administrator. If the value is persistent(2), the binding was created by the switch because the VLAN is the port-based VLAN for the switch port, or the switch port VLAN Binding Method is persistent. These bindings may not be removed. If the value is dynamic(3), the binding was created by the switch as a result of receiving a tagged frame on the switch port with a VLAN ID corresponding to the VLAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	static(1), persistent(2), dynamic(3)

lanBlazer7000VirtualSwitchPortStatus		1.3.6.1.4.1.50.8.1.2.1.7.4.1.1.5
The status of an entry to be created or deleted. When adding an entry all fields will be set, and then the status is set to createRequest(1) (indicating that the entry is to be created). When deleting an entry the status is set to destroyRequest(2) (indicating that the entry is to be destroyed). If the creation is successful, then the status will be set to active(3). Otherwise if the creation was not successful then one of the following error codes will be set and the entry will not be created: otherError(4) - An error other than the others defined. entryExistsError(5) - On creation, an entry already exists. On deletion, the entry may not be removed. entryNoExistError(6) - The VLAN specified by ID does not exist.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	createRequest(1), destroyRequest(2), active(3), otherError(4), entryExistsError(5), entryNoExistError(6)

lanBlazer7000Events		1.3.6.1.4.1.50.8.1.2.1.10
OBJECT IDENTIFIER

lanBlazer7000EventMgt		1.3.6.1.4.1.50.8.1.2.1.10.1
OBJECT IDENTIFIER

lanBlazer7000EventTable		1.3.6.1.4.1.50.8.1.2.1.10.1.1
Table of events currently supported.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000EventEntry

lanBlazer7000EventEntry		1.3.6.1.4.1.50.8.1.2.1.10.1.1.1
Attributes associated with the event.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000EventEntry

lanBlazer7000EventIndex		1.3.6.1.4.1.50.8.1.2.1.10.1.1.1.1
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000EventMode		1.3.6.1.4.1.50.8.1.2.1.10.1.1.1.2
Disabling an event prevents this event from taking any actions when triggered. When set to enable to the console, the event will print the event information to the console serial port. The user can select whether to view log messages, trap messages or any event at the console.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000EventLogAction		1.3.6.1.4.1.50.8.1.2.1.10.1.1.1.3
When enabled, this action will cause an event log entry to be created.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000EventTrapAction		1.3.6.1.4.1.50.8.1.2.1.10.1.1.1.4
When enabled, this event will cause an SNMP trap to be generated.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000EventConsoleAction		1.3.6.1.4.1.50.8.1.2.1.10.1.1.1.5
When enabled, this event will cause a message to printed to the console serial port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000EventLogMgt		1.3.6.1.4.1.50.8.1.2.1.10.2
OBJECT IDENTIFIER

lanBlazer7000LogTableMaxSize		1.3.6.1.4.1.50.8.1.2.1.10.2.1
The maximum number of entries in the log table. Changing this value causes the existing log to be truncated and rebuilt.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..2048

lanBlazer7000LogLastEntry		1.3.6.1.4.1.50.8.1.2.1.10.2.2
The log index of the last entry entered in the log.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

lanBlazer7000LogWraps		1.3.6.1.4.1.50.8.1.2.1.10.2.3
The number of times that the last entry has wrapped from 65K back to 1.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

lanBlazer7000EventLog		1.3.6.1.4.1.50.8.1.2.1.10.3
OBJECT IDENTIFIER

lanBlazer7000EventLogTable		1.3.6.1.4.1.50.8.1.2.1.10.3.1
The log table for the events in the event table that are enabled for the Log Action.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000EventLogEntry

lanBlazer7000EventLogEntry		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1
An entry in the log indicates information associated with a particular event.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000EventLogEntry

lanBlazer7000EventLogEventIndex		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1.1
The index that uniquely identifies the event that caused this log entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

lanBlazer7000EventLogIndex		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1.2
An index that uniquely identifies this log entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

lanBlazer7000EventLogTime		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1.3
The value of sysUpTime when this event was triggered.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

lanBlazer7000EventLogDescr		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1.4
The event log description.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

lanBlazer7000EventLogType		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1.5
The type of event that caused this log entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	EventCategory

lanBlazer7000EventLogSeverity		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1.6
The severity associated with this event. It is recommended that the severity be interpreted in the following manner: 0-19: Normal 20-39: Informational 40-59: Warning 60-79: Alarm 80-99: Severe Error 100: Failure.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..100

lanBlazer7000EventLogDTM		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1.7
The date and time when this log entry was made. The format is yy-Mon- dd hh:mm:ss, time is in 24 hour time.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(18)

lanBlazer7000EventLogResType		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1.8
The type of object (if provided) that triggered this event. If not provided, the value is equal to 'Invalid Resource'.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceType

lanBlazer7000EventLogResID		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1.9
The instance of this resource (if provided - see lanBlazer7000EventLogResType) that triggered this event.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000EventLogResLeaf		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1.10
A number corresponding to the attribute associated with this resource and this event entry. It corresponds exactly to the leaf MIB number of the MIB that manages this resource. For example, if a port's mode changed, the configuration event log entry would indicate the value of 5 which is the leaf index of the lanBlazer7000PortMode within the lanBlazer7000PortTable MIB table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000EventLogValueType		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1.11
The data type associated with the log event value. This object indicates how to interpret the data stored in the event log value: - none(1) indicates no value returned. - integer32(2) - a 4 byte unsigned integer. - integer64(3) - an 8 byte unsigned integer. - displayString(4) - a null terminated (or up to 8 characters) string. - ipv4NetworkAddress(5) - a 4 byte IP version 4 network address. - ieee802MACAddress(6) - a 6 byte MAC Address. - timeticks(7) - sysUpTime type value (4 bytes)
Status: mandatory	Access: read-only
OBJECT-TYPE
	EventValueType

lanBlazer7000EventLogValue		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1.12
The value associated with the event encoded in an octet string. Refer to lanBlazer7000EventLogValueType for how to interpret this value. The value encoded in this string is in Big Endian order.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..8)

lanBlazer7000EventLogEpochTime		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1.13
The number of time ticks since the epoch when this event was logged. The interpretation of this value is as follows: struct DateTimeOvly { UNS32 year:6; UNS32 month:4; UNS32 day:5; UNS32 hour:5; UNS32 minute:6; UNS32 second:6; }; The epoch is January 1, 1997, at 00:00:00. A value of 0 refers to this date and time.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000EventLogID		1.3.6.1.4.1.50.8.1.2.1.10.3.1.1.14
A unique index that identifies the occurence of this event. This ID can be correlated between traps, logs and the like.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

lanBlazer7000ShutdownLogMgt		1.3.6.1.4.1.50.8.1.2.1.10.4
OBJECT IDENTIFIER

lanBlazer7000ShutdownLogTableMaxSize		1.3.6.1.4.1.50.8.1.2.1.10.4.1
The maximum number of entries in the non-volatile log table. Changing the value of this object changes the maximum number of entries to be stored in Shutdown.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..128

lanBlazer7000ShutdownLogLastEntry		1.3.6.1.4.1.50.8.1.2.1.10.4.2
The ID of the last entry made to the shutdown log.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

lanBlazer7000ShutdownLogAcknowledged		1.3.6.1.4.1.50.8.1.2.1.10.4.3
This object is to set to acknowledged(2) the first time the Shutdown Log Table is accessed indicating that the Shutdown log has been read (at least once) since the system restarted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	not-acknowledged(1), acknowledged(2)

lanBlazer7000EventShutdownLog		1.3.6.1.4.1.50.8.1.2.1.10.5
OBJECT IDENTIFIER

lanBlazer7000EventShutdownLogTable		1.3.6.1.4.1.50.8.1.2.1.10.5.1
A table of the last events logged before the system restarted.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000EventShutdownLogEntry

lanBlazer7000EventShutdownLogEntry		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1
A log entry stored in non-volatile memory.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000EventShutdownLogEntry

lanBlazer7000EventShutdownLogEventIndex		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1.1
The index that uniquely identifies the event that caused this ShutdownLog entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

lanBlazer7000EventShutdownLogIndex		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1.2
An index that uniquely identifies this ShutdownLog entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

lanBlazer7000EventShutdownLogTime		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1.3
The value of sysUpTime when this event was triggered. Note, the value corresponds to the sysUpTime when the system was last running (i.e. before it was shutdown.)
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

lanBlazer7000EventShutdownLogDescr		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1.4
The event ShutdownLog description.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

lanBlazer7000EventShutdownLogType		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1.5
The type of event that caused this ShutdownLog entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	EventCategory

lanBlazer7000EventShutdownLogSeverity		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1.6
The severity associated with this event. It is recommended that the severity be interpreted in the following manner: 0-19: Normal 20-39: Informational 40-59: Warning 60-79: Alarm 80-99: Severe Error 100: Failure.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..100

lanBlazer7000EventShutdownLogDTM		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1.7
The date and time when this ShutdownLog entry was made. The format is yy-Mon-dd hh:mm:ss, time is in 24 hour time.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(18)

lanBlazer7000EventShutdownLogResType		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1.8
The type of object (if provided) that triggered this event. If not provided, the value is invalid.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceType

lanBlazer7000EventShutdownLogResID		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1.9
The instance of this resource (if provided) that triggered this event.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000EventShutdownLogResLeaf		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1.10
To be provided.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000EventShutdownLogValueType		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1.11
The data type associated with the ShutdownLog event value. This object indicates how to interpret the data stored in the event ShutdownLog value.
Status: mandatory	Access: read-only
OBJECT-TYPE
	EventValueType

lanBlazer7000EventShutdownLogValue		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1.12
The value associated with the event encoded in an octet string.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..8)

lanBlazer7000EventShutdownLogEpochTime		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1.13
The number of time ticks since the epoch when this event was logged. The interpretation of this value is as follows: struct DateTimeOvly { UNS32 year:6; UNS32 month:4; UNS32 day:5; UNS32 hour:5; UNS32 minute:6; UNS32 second:6; }; The epoch is January 1, 1997, at 00:00:00. A value of 0 refers to this date and time.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000EventShutdownLogID		1.3.6.1.4.1.50.8.1.2.1.10.5.1.1.14
A unique index that identifies the occurence of this event. This ID can be correlated between traps, logs and the like.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

lanBlazer7000EventTrapMgmt		1.3.6.1.4.1.50.8.1.2.1.10.6
OBJECT IDENTIFIER

lanBlazer7000EventTrapEventIndex		1.3.6.1.4.1.50.8.1.2.1.10.6.1
The index that uniquely identifies the event that caused this trap.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

lanBlazer7000EventTrapTime		1.3.6.1.4.1.50.8.1.2.1.10.6.2
The value of sysUpTime when this event was triggered.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

lanBlazer7000EventTrapDescr		1.3.6.1.4.1.50.8.1.2.1.10.6.3
The event log description.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

lanBlazer7000EventTrapType		1.3.6.1.4.1.50.8.1.2.1.10.6.4
The type of event that caused this trap.
Status: mandatory	Access: read-only
OBJECT-TYPE
	EventCategory

lanBlazer7000EventTrapSeverity		1.3.6.1.4.1.50.8.1.2.1.10.6.5
The severity associated with this event. It is recommended that the severity be interpreted in the following manner: 0-19: Normal 20-39: Informational 40-59: Warning 60-79: Alarm 80-99: Severe Error 100: Failure.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..100

lanBlazer7000EventTrapDTM		1.3.6.1.4.1.50.8.1.2.1.10.6.6
The date and time when this trap was sent. The format is yy-Mon- dd hh:mm:ss, time is in 24 hour time.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(18)

lanBlazer7000EventTrapResType		1.3.6.1.4.1.50.8.1.2.1.10.6.7
The type of object (if provided) that triggered this event. If not provided, the value is equal to 'Invalid Resource'.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceType

lanBlazer7000EventTrapResID		1.3.6.1.4.1.50.8.1.2.1.10.6.8
The instance of this resource (if provided - see lanBlazer7000EventTrapResType) that triggered this event.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000EventTrapResLeaf		1.3.6.1.4.1.50.8.1.2.1.10.6.9
A number corresponding to the attribute associated with this resource and this event entry. It corresponds exactly to the leaf MIB number of the MIB that manages this resource. For example, if a port's mode changed, the configuration event log entry would indicate the value of 5 which is the leaf index of the lanBlazer7000PortMode within the lanBlazer7000PortTable MIB table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000EventTrapValueType		1.3.6.1.4.1.50.8.1.2.1.10.6.10
The data type associated with the trap event value. This object indicates how to interpret the data stored in the event trap value: - none(1) indicates no value returned. - integer32(2) - a 4 byte unsigned integer. - integer64(3) - an 8 byte unsigned integer. - displayString(4) - a null terminated (or up to 8 characters) string. - ipv4NetworkAddress(5) - a 4 byte IP version 4 network address. - ieee802MACAddress(6) - a 6 byte MAC Address. - timeticks(7) - sysUpTime type value (4 bytes)
Status: mandatory	Access: read-only
OBJECT-TYPE
	EventValueType

lanBlazer7000EventTrapValue		1.3.6.1.4.1.50.8.1.2.1.10.6.11
The value associated with the event encoded in an octet string. Refer to lanBlazer7000EventTrapValueType for how to interpret this value. The value encoded in this string is in Big Endian order.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..8)

lanBlazer7000EventTrapEpochTime		1.3.6.1.4.1.50.8.1.2.1.10.6.12
The number of time ticks since the epoch when this event was logged. The interpretation of this value is as follows: struct DateTimeOvly { UNS32 year:6; UNS32 month:4; UNS32 day:5; UNS32 hour:5; UNS32 minute:6; UNS32 second:6; }; The epoch is January 1, 1997, at 00:00:00. A value of 0 refers to this date and time.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000EventTrapID		1.3.6.1.4.1.50.8.1.2.1.10.6.13
A unique index that identifies the occurence of this event. This ID can be correlated between traps, logs and the like.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

lanBlazer7000AlarmMgt		1.3.6.1.4.1.50.8.1.2.1.11
OBJECT IDENTIFIER

lanBlazer7000AlarmGeneral		1.3.6.1.4.1.50.8.1.2.1.11.1
OBJECT IDENTIFIER

lanBlazer7000AlarmGeneralActiveEntries		1.3.6.1.4.1.50.8.1.2.1.11.1.1
The total number of alarm entries in the triggered state currently in the alarm table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

lanBlazer7000AlarmGeneralTimeStamp		1.3.6.1.4.1.50.8.1.2.1.11.1.2
The value of sysUpTime when any alarm state last changed (either triggering a new alarm or re-arming an old one).
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

lanBlazer7000Alarms		1.3.6.1.4.1.50.8.1.2.1.11.2
OBJECT IDENTIFIER

lanBlazer7000ActiveAlarmTable		1.3.6.1.4.1.50.8.1.2.1.11.2.2
A table of all alarms in the triggered state.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LanBlazer7000ActiveAlarmEntry

lanBlazer7000ActiveAlarmEntry		1.3.6.1.4.1.50.8.1.2.1.11.2.2.1
An alarm in the triggered state.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	LanBlazer7000ActiveAlarmEntry

lanBlazer7000ActiveAlarmIndex		1.3.6.1.4.1.50.8.1.2.1.11.2.2.1.1
The unique index that identifies this alarm.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000ActiveAlarmName		1.3.6.1.4.1.50.8.1.2.1.11.2.2.1.2
The name of this alarm.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..31)

lanBlazer7000ActiveAlarmValueHigh		1.3.6.1.4.1.50.8.1.2.1.11.2.2.1.3
The high order 32 bits of the value that triggered this alarm.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000ActiveAlarmValueLow		1.3.6.1.4.1.50.8.1.2.1.11.2.2.1.4
The low order 32 bits of the value that triggered this alarm.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000ActiveAlarmVariable		1.3.6.1.4.1.50.8.1.2.1.11.2.2.1.5
The OID of the alarm variable if this is a user-created alarm (null otherwise).
Status: mandatory	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

lanBlazer7000ActiveAlarmResType		1.3.6.1.4.1.50.8.1.2.1.11.2.2.1.6
The resource type of this alarm if this is an internally created alarm.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceType

lanBlazer7000ActiveAlarmResID		1.3.6.1.4.1.50.8.1.2.1.11.2.2.1.7
The resource identifier associated with this alarm if this is an internally created alarm.
Status: mandatory	Access: read-only
OBJECT-TYPE
	ResourceId

lanBlazer7000ActiveAlarmLeaf		1.3.6.1.4.1.50.8.1.2.1.11.2.2.1.8
The leaf index of the MIB table used to manage this resource that is associated with this alarm, if this is an internally created alarm. For example, if this alarm was created to monitor a port's status, then the value of this object will be 6, corresponding to the leaf index of the lanBlazer7000PortStatus object.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lanBlazer7000ActiveAlarmOwner		1.3.6.1.4.1.50.8.1.2.1.11.2.2.1.9
This is the owner of the alarm.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

lanBlazer7000SnmpTraps		1.3.6.1.4.1.50.8.1.2.1.13
OBJECT IDENTIFIER

lanBlazer7000SystemTrap		2
A lanBlazer7000SystemTrap is sent by the agent when a system event is triggered. These events are usually triggered when the software encounters an unexpected situation, e.g. a hardware failure or a software bug.
TRAP-TYPE

lanBlazer7000ConfigurationTrap		3
A lanBlazer7000ConfigurationTrap is sent by the agent when the configuration event is triggered. These events are triggered when a configuration change is made.
TRAP-TYPE

lanBlazer7000TemperatureTrap		4
A lanBlazer7000TemperatureTrap is sent by the agent when the temperature event is triggered. This event is triggered when a temperature probe detects the temperature crossing a threshold.
TRAP-TYPE

lanBlazer7000ResourceTrap		5
A lanBlazer7000ResourceTrap is sent by the agent when the resource event is triggered. The resource event is triggered when a resource is added or removed from the system.
TRAP-TYPE

lanBlazer7000FanTrap		6
A lanBlazer7000FanTrap is sent by the agent when the fan status event is triggered. The fan status event is triggered when a fan has a change in its status.
TRAP-TYPE

lanBlazer7000PowerTrap		9
A lanBlazer7000PowerTrap is sent by the agent when the power event is triggered. These events are triggered when a power supply changes status.
TRAP-TYPE

lanBlazer7000VlanExchange		1.3.6.1.4.1.50.8.1.2.1.14
OBJECT IDENTIFIER

lanBlazer7000VlanExchangeSwitch		1.3.6.1.4.1.50.8.1.2.1.14.1
OBJECT IDENTIFIER

lanBlazer7000VlanExchangeState		1.3.6.1.4.1.50.8.1.2.1.14.1.1
When this object is set to enable(1), the switch attempts to learn VLANs from a major networking equipment vendor on switch ports that have their VLAN Exchange parameter set to enable(1). trunking mode is IEEE 802.1Q Format or Multi-level Format. The factory default value for this object is disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lanBlazer7000VlanExchangeDomainName		1.3.6.1.4.1.50.8.1.2.1.14.1.2
The VLAN Exchange Domain Name of the switch. A switch may only belong to one domain.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

lanBlazer7000VlanExchangeUpdaterId		1.3.6.1.4.1.50.8.1.2.1.14.1.3
The IP address of the switch from which the VLAN Exchange configuration was learned.
Status: mandatory	Access: read-only
OBJECT-TYPE
	NetworkAddress

lanBlazer7000VlanExchangeUpdateTimeStamp		1.3.6.1.4.1.50.8.1.2.1.14.1.4
The time at which the VLAN Exchange configuration changed on the initiating switch.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..12)

lanBlazer7000VlanExchangeConfigRevNum		1.3.6.1.4.1.50.8.1.2.1.14.1.5
Configuration Revision Number of VLAN Exchange Configuration on the switch that initiated the VLAN Exchange.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor