OMNI-gx2LME-MIB

File: OMNI-gx2LME-MIB.mib (105412 bytes)

Imported modules

RFC1155-SMI	RFC-1212	RFC1213-MIB
RFC-1215	NLS-BBNIDENT-MIB	GX2HFC-MIB
NLSBBN-TRAPS-MIB

Imported symbols

IpAddress	TimeTicks	Counter
OBJECT-TYPE	sysUpTime	DisplayString
TRAP-TYPE	gi	motproxies
gx2LmE	trapIdentifier	trapNetworkElemModelNumber
trapNetworkElemSerialNum	trapPerceivedSeverity	trapNetworkElemOperState
trapNetworkElemAlarmStatus	trapNetworkElemAdminState	trapNetworkElemAvailStatus
trapText	trapNETrapLastTrapTimeStamp	trapChangedObjectId
trapChangedValueInteger	trapChangedValueDisplayString

Defined Types

Float
Counter

Gx2lmeAnalogEntry
SEQUENCE
	gx2lmeAnalogTableIndex	INTEGER
	lmelabelOffsetNomMonitor	DisplayString	Size(0..80)
	lmeuomOffsetNomMonitor	DisplayString	Size(0..80)
	lmemajorHighOffsetNomMonitor	Float
	lmemajorLowOffsetNomMonitor	Float
	lmeminorHighOffsetNomMonitor	Float
	lmeminorLowOffsetNomMonitor	Float
	lmecurrentValueOffsetNomMonitor	Float
	lmestateFlagOffsetNomMonitor	INTEGER
	lmeminValueOffsetNomMonitor	Float
	lmemaxValueOffsetNomMonitor	Float
	lmealarmStateOffsetNomMonitor	INTEGER
	lmelabelOffsetNomCnt	DisplayString	Size(0..80)
	lmeuomOffsetNomCnt	DisplayString	Size(0..80)
	lmemajorHighOffsetNomCnt	Float
	lmemajorLowOffsetNomCnt	Float
	lmeminorHighOffsetNomCnt	Float
	lmeminorLowOffsetNomCnt	Float
	lmecurrentValueOffsetNomCnt	Float
	lmestateFlagOffsetNomCnt	INTEGER
	lmeminValueOffsetNomCnt	Float
	lmemaxValueOffsetNomCnt	Float
	lmealarmStateOffsetNomCnt	INTEGER
	lmelabelRelAttenSetting	DisplayString	Size(0..80)
	lmeuomRelAttenSetting	DisplayString	Size(0..80)
	lmemajorHighRelAttenSetting	Float
	lmemajorLowRelAttenSetting	Float
	lmeminorHighRelAttenSetting	Float
	lmeminorLowRelAttenSetting	Float
	lmecurrentValueRelAttenSetting	Float
	lmestateFlagRelAttenSetting	INTEGER
	lmeminValueRelAttenSetting	Float
	lmemaxValueRelAttenSetting	Float
	lmealarmStateRelAttenSetting	INTEGER
	lmelabelOptPower	DisplayString	Size(0..80)
	lmeuomOptPower	DisplayString	Size(0..80)
	lmemajorHighOptPower	Float
	lmemajorLowOptPower	Float
	lmeminorHighOptPower	Float
	lmeminorLowOptPower	Float
	lmecurrentValueOptPower	Float
	lmestateFlagOptPower	INTEGER
	lmeminValueOptPower	Float
	lmemaxValueOptPower	Float
	lmealarmStateOptPower	INTEGER
	lmelabelLaserBias	DisplayString	Size(0..80)
	lmeuomLaserBias	DisplayString	Size(0..80)
	lmemajorHighLaserBias	Float
	lmemajorLowLaserBias	Float
	lmeminorHighLaserBias	Float
	lmeminorLowLaserBias	Float
	lmecurrentValueLaserBias	Float
	lmestateFlagLaserBias	INTEGER
	lmeminValueLaserBias	Float
	lmemaxValueLaserBias	Float
	lmealarmStateLaserBias	INTEGER
	lmelabelTecCurrent	DisplayString	Size(0..80)
	lmeuomTecCurrent	DisplayString	Size(0..80)
	lmemajorHighTecCurrent	Float
	lmemajorLowTecCurrent	Float
	lmeminorHighTecCurrent	Float
	lmeminorLowTecCurrent	Float
	lmecurrentValueTecCurrent	Float
	lmestateFlagTecCurrent	INTEGER
	lmeminValueTecCurrent	Float
	lmemaxValueTecCurrent	Float
	lmealarmStateTecCurrent	INTEGER
	lmelabelLaserTemp	DisplayString	Size(0..80)
	lmeuomLaserTemp	DisplayString	Size(0..80)
	lmemajorHighLaserTemp	Float
	lmemajorLowLaserTemp	Float
	lmeminorHighLaserTemp	Float
	lmeminorLowLaserTemp	Float
	lmecurrentValueLaserTemp	Float
	lmestateFlagLaserTemp	INTEGER
	lmeminValueLaserTemp	Float
	lmemaxValueLaserTemp	Float
	lmealarmStateLaserTemp	INTEGER
	lmelabelModuleTemp	DisplayString	Size(0..80)
	lmeuomModuleTemp	DisplayString	Size(0..80)
	lmemajorHighModuleTemp	Float
	lmemajorLowModuleTemp	Float
	lmeminorHighModuleTemp	Float
	lmeminorLowModuleTemp	Float
	lmecurrentValueModuleTemp	Float
	lmestateFlagModuleTemp	INTEGER
	lmeminValueModuleTemp	Float
	lmemaxValueModuleTemp	Float
	lmealarmStateModuleTemp	INTEGER
	lmelabelFanCurrent	DisplayString	Size(0..80)
	lmeuomFanCurrent	DisplayString	Size(0..80)
	lmemajorHighFanCurrent	Float
	lmemajorLowFanCurrent	Float
	lmeminorHighFanCurrent	Float
	lmeminorLowFanCurrent	Float
	lmecurrentValueFanCurrent	Float
	lmestateFlagFanCurrent	INTEGER
	lmeminValueFanCurrent	Float
	lmemaxValueFanCurrent	Float
	lmealarmStateFanCurrent	INTEGER
	lmelabel12Volt	DisplayString	Size(0..80)
	lmeuom12Volt	DisplayString	Size(0..80)
	lmemajorHigh12Volt	Float
	lmemajorLow12Volt	Float
	lmeminorHigh12Volt	Float
	lmeminorLow12Volt	Float
	lmecurrentValue12Volt	Float
	lmestateFlag12Volt	INTEGER
	lmeminValue12Volt	Float
	lmemaxValue12Volt	Float
	lmealarmState12Volt	INTEGER

Gx2lmeDigitalEntry
SEQUENCE
	gx2lmeDigitalTableIndex	INTEGER
	lmelabelRfInput	DisplayString	Size(0..80)
	lmeenumRfInput	DisplayString	Size(0..80)
	lmevalueRfInput	INTEGER
	lmestateflagRfInput	INTEGER
	lmelabelOptOutput	DisplayString	Size(0..80)
	lmeenumOptOutput	DisplayString	Size(0..80)
	lmevalueOptOutput	INTEGER
	lmestateflagOptOutput	INTEGER
	lmelabelLaserMode	DisplayString	Size(0..80)
	lmeenumLaserMode	DisplayString	Size(0..80)
	lmevalueLaserMode	INTEGER
	lmestateflagLaserMode	INTEGER
	lmelabelLaserSecMode	DisplayString	Size(0..80)
	lmeenumLaserSecMode	DisplayString	Size(0..80)
	lmevalueLaserSecMode	INTEGER
	lmestateflagLaserSecMode	INTEGER
	lmelabelVideoOffset	DisplayString	Size(0..80)
	lmeenumVideoOffset	DisplayString	Size(0..80)
	lmevalueVideoOffset	INTEGER
	lmestateflagVideoOffset	INTEGER
	lmelabelFactoryDefault	DisplayString	Size(0..80)
	lmeenumFactoryDefault	DisplayString	Size(0..80)
	lmevalueFactoryDefault	INTEGER
	lmestateflagFactoryDefault	INTEGER
	lmelabelFiberLength	DisplayString	Size(0..80)
	lmeenumFiberLength	DisplayString	Size(0..80)
	lmevalueFiberLength	INTEGER
	lmestateflagFiberLength	INTEGER
	lmelabelConditioningUnit	DisplayString	Size(0..80)
	lmeenumConditioningUnit	DisplayString	Size(0..80)
	lmevalueConditioningUnit	INTEGER
	lmestateflagConditioningUnit	INTEGER

Gx2lmeStatusEntry
SEQUENCE
	gx2lmeStatusTableIndex	INTEGER
	lmelabelBoot	DisplayString	Size(0..80)
	lmevalueBoot	INTEGER
	lmestateflagBoot	INTEGER
	lmelabelFlash	DisplayString	Size(0..80)
	lmevalueFlash	INTEGER
	lmestateflagFlash	INTEGER
	lmelabelFactoryDataCRC	DisplayString	Size(0..80)
	lmevalueFactoryDataCRC	INTEGER
	lmestateflagFactoryDataCRC	INTEGER
	lmelabelLaserDataCRC	DisplayString	Size(0..80)
	lmevalueLaserDataCRC	INTEGER
	lmestateflagLaserDataCRC	INTEGER
	lmelabelAlarmDataCrc	DisplayString	Size(0..80)
	lmevalueAlarmDataCrc	INTEGER
	lmestateflagAlarmDataCrc	INTEGER
	lmelabelHWStatus	DisplayString	Size(0..80)
	lmevalueHWStatus	INTEGER
	lmestateflagHWStatus	INTEGER
	lmelabelRFInputStatus	DisplayString	Size(0..80)
	lmevalueRFInputStatus	INTEGER
	lmestateflagRFInputStatus	INTEGER

Gx2lmeFactoryEntry
SEQUENCE
	gx2lmeFactoryTableIndex	INTEGER
	lmebootControlByteValue	INTEGER
	lmebootStatusByteValue	INTEGER
	lmebank1CRCValue	INTEGER
	lmebank2CRCValue	INTEGER
	lmeprgEEPROMByteValue	INTEGER
	lmefactoryCRCValue	INTEGER
	lmecalculateCRCValue	INTEGER
	lmehourMeterValue	INTEGER
	lmeflashPrgCntAValue	INTEGER
	lmeflashPrgCntBValue	INTEGER
	lmeflashBankARevValue	DisplayString	Size(0..80)
	lmeflashBankBRevValue	DisplayString	Size(0..80)

Gx2Lm1000EHoldTimeEntry
SEQUENCE
	gx2Lm1000EHoldTimeTableIndex	INTEGER
	gx2Lm1000EHoldTimeSpecIndex	INTEGER
	gx2Lm1000EHoldTimeData	INTEGER

Defined Values

gx2lmeDescriptor		1.3.6.1.4.1.1166.6.1.2.27.1
OBJECT IDENTIFIER

gx2lmeAnalogTable		1.3.6.1.4.1.1166.6.1.2.27.2
This table contains gx2LmE specific parameters with nominal and current values.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Gx2lmeAnalogEntry

gx2lmeAnalogEntry		1.3.6.1.4.1.1166.6.1.2.27.2.1
This list contains the analog parameters and descriptions.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Gx2lmeAnalogEntry

gx2lmeDigitalTable		1.3.6.1.4.1.1166.6.1.2.27.3
This table contains gx2LmE specific parameters with nominal and current values.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Gx2lmeDigitalEntry

gx2lmeDigitalEntry		1.3.6.1.4.1.1166.6.1.2.27.3.2
This list contains digital parameters and descriptions.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Gx2lmeDigitalEntry

gx2lmeStatusTable		1.3.6.1.4.1.1166.6.1.2.27.4
This table contains gx2LmE specific parameters with nominal and current values.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Gx2lmeStatusEntry

gx2lmeStatusEntry		1.3.6.1.4.1.1166.6.1.2.27.4.3
This list contains Status parameters and descriptions.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Gx2lmeStatusEntry

gx2lmeFactoryTable		1.3.6.1.4.1.1166.6.1.2.27.5
This table contains gx2LmE specific parameters with nominal and current values.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Gx2lmeFactoryEntry

gx2lmeFactoryEntry		1.3.6.1.4.1.1166.6.1.2.27.5.4
This list contains Factory parameters and descriptions.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Gx2lmeFactoryEntry

gx2Lm1000EHoldTimeTable		1.3.6.1.4.1.1166.6.1.2.27.6
This table contains gx2Lm1000E specific parameters with nominal and current values.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Gx2Lm1000EHoldTimeEntry

gx2Lm1000EHoldTimeEntry		1.3.6.1.4.1.1166.6.1.2.27.6.5
This list contains digital product class and the associated RF channel parameters and descriptions.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Gx2Lm1000EHoldTimeEntry

gx2lmeAnalogTableIndex		1.3.6.1.4.1.1166.6.1.2.27.2.1.1
The value of this object identifies the network element. This index is equal to the hfcCommonTableIndex for the same element.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4294967295

lmelabelOffsetNomMonitor		1.3.6.1.4.1.1166.6.1.2.27.2.1.2
The value of this object provides the label of the Offset Monitor Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeuomOffsetNomMonitor		1.3.6.1.4.1.1166.6.1.2.27.2.1.3
The value of this object provides the Unit of Measure of the Offset Monitor Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmemajorHighOffsetNomMonitor		1.3.6.1.4.1.1166.6.1.2.27.2.1.4
The value of this object provides the Major High alarm value of the Offset Monitor Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemajorLowOffsetNomMonitor		1.3.6.1.4.1.1166.6.1.2.27.2.1.5
The value of this object provides the Major Low alarm value of the Offset Monitor Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorHighOffsetNomMonitor		1.3.6.1.4.1.1166.6.1.2.27.2.1.6
The value of this object provides the Minor High alarm value of the Offset Monitor Analog parameter. This value is a float and is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorLowOffsetNomMonitor		1.3.6.1.4.1.1166.6.1.2.27.2.1.7
The value of this object provides the Minor Low alarm value of the Offset Monitor Analog parameter. This value is a float and is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmecurrentValueOffsetNomMonitor		1.3.6.1.4.1.1166.6.1.2.27.2.1.8
The value of this object provides the Current value of the Offset Monitor Analog parameter. This value is a float and is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmestateFlagOffsetNomMonitor		1.3.6.1.4.1.1166.6.1.2.27.2.1.9
The value of this object provides the state of the Offset Monitor Analog parameter. (0-Hidden 1-Read-Only, 2-Updateable)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmeminValueOffsetNomMonitor		1.3.6.1.4.1.1166.6.1.2.27.2.1.10
The value of this object provides the minimum value the Offset Monitor Analog parameter can achive. This value is a float and is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemaxValueOffsetNomMonitor		1.3.6.1.4.1.1166.6.1.2.27.2.1.11
The value of this object provides the maximum value the Offset Monitor Analog parameter can achive. This value is a float and is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmealarmStateOffsetNomMonitor		1.3.6.1.4.1.1166.6.1.2.27.2.1.12
The value of this object provides the curent alarm state of the Offset Monitor Analog parameter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), majorLowAlarm(2), minorLowAlarm(3), minorHighAlarm(4), majorHighAlarm(5), informational(6)

lmelabelOffsetNomCnt		1.3.6.1.4.1.1166.6.1.2.27.2.1.13
The value of this object provides the label of the Offset Control Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeuomOffsetNomCnt		1.3.6.1.4.1.1166.6.1.2.27.2.1.14
The value of this object provides the label of the Offset Control Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmemajorHighOffsetNomCnt		1.3.6.1.4.1.1166.6.1.2.27.2.1.15
The value of this object provides the Major High alarm value of the Offset Control Analog parameter. This value is a float and is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemajorLowOffsetNomCnt		1.3.6.1.4.1.1166.6.1.2.27.2.1.16
The value of this object provides the Major Low alarm value of the Offset Control Analog parameter. This value is a float and is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorHighOffsetNomCnt		1.3.6.1.4.1.1166.6.1.2.27.2.1.17
The value of this object provides the Minor High alarm value of the Offset Control Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorLowOffsetNomCnt		1.3.6.1.4.1.1166.6.1.2.27.2.1.18
The value of this object provides the Minor Low alarm value of the Offset Control Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmecurrentValueOffsetNomCnt		1.3.6.1.4.1.1166.6.1.2.27.2.1.19
The value of this object provides the Current value of the Offset Control Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Float

lmestateFlagOffsetNomCnt		1.3.6.1.4.1.1166.6.1.2.27.2.1.20
The value of this object provides the state of the Offset Control Analog parameter. (0-Hidden 1-Read-Only, 2-Updateable)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmeminValueOffsetNomCnt		1.3.6.1.4.1.1166.6.1.2.27.2.1.21
The value of this object provides the minimum value the Offset Control Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemaxValueOffsetNomCnt		1.3.6.1.4.1.1166.6.1.2.27.2.1.22
The value of this object provides the maximum value the Offset Control Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmealarmStateOffsetNomCnt		1.3.6.1.4.1.1166.6.1.2.27.2.1.23
The value of this object provides the curent alarm state of the Offset Control Analog parameter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), majorLowAlarm(2), minorLowAlarm(3), minorHighAlarm(4), majorHighAlarm(5), informational(6)

lmelabelRelAttenSetting		1.3.6.1.4.1.1166.6.1.2.27.2.1.24
The value of this object provides the label of the Attenuator Setting Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeuomRelAttenSetting		1.3.6.1.4.1.1166.6.1.2.27.2.1.25
The value of this object provides the Unit of Measure of the Attenuator Setting Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmemajorHighRelAttenSetting		1.3.6.1.4.1.1166.6.1.2.27.2.1.26
The value of this object provides the Major High alarm value of the Attenuator Setting Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemajorLowRelAttenSetting		1.3.6.1.4.1.1166.6.1.2.27.2.1.27
The value of this object provides the Major Low alarm value of the Attenuator Setting Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorHighRelAttenSetting		1.3.6.1.4.1.1166.6.1.2.27.2.1.28
The value of this object provides the Minor High alarm value of the Attenuator Setting Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorLowRelAttenSetting		1.3.6.1.4.1.1166.6.1.2.27.2.1.29
The value of this object provides the Minor Low alarm value of the Attenuator Setting Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmecurrentValueRelAttenSetting		1.3.6.1.4.1.1166.6.1.2.27.2.1.30
The value of this object provides the Current value of the Attenuator Setting Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Float

lmestateFlagRelAttenSetting		1.3.6.1.4.1.1166.6.1.2.27.2.1.31
The value of this object provides the state of the Attenuator Setting Analog parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmeminValueRelAttenSetting		1.3.6.1.4.1.1166.6.1.2.27.2.1.32
The value of this object provides the minimum value the Attenuator Setting Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemaxValueRelAttenSetting		1.3.6.1.4.1.1166.6.1.2.27.2.1.33
The value of this object provides the maximum value the Attenuator Setting Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmealarmStateRelAttenSetting		1.3.6.1.4.1.1166.6.1.2.27.2.1.34
The value of this object provides the curent alarm state of the Attenuator Setting Analog parameter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), majorLowAlarm(2), minorLowAlarm(3), minorHighAlarm(4), majorHighAlarm(5), informational(6)

lmelabelOptPower		1.3.6.1.4.1.1166.6.1.2.27.2.1.35
The value of this object provides the label of the Optical Power Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeuomOptPower		1.3.6.1.4.1.1166.6.1.2.27.2.1.36
The value of this object provides the Unit of Measure of the Optical Power Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmemajorHighOptPower		1.3.6.1.4.1.1166.6.1.2.27.2.1.37
The value of this object provides the Major High alarm value of the Optical Power Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemajorLowOptPower		1.3.6.1.4.1.1166.6.1.2.27.2.1.38
The value of this object provides the Major Low alarm value of the Optical Power Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorHighOptPower		1.3.6.1.4.1.1166.6.1.2.27.2.1.39
The value of this object provides the Minor High alarm value of the Optical Power Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorLowOptPower		1.3.6.1.4.1.1166.6.1.2.27.2.1.40
The value of this object provides the Minor Low alarm value of the Optical Power Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmecurrentValueOptPower		1.3.6.1.4.1.1166.6.1.2.27.2.1.41
The value of this object provides the Current value of the Optical Power Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmestateFlagOptPower		1.3.6.1.4.1.1166.6.1.2.27.2.1.42
The value of this object provides the state of the Optical Power Analog parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmeminValueOptPower		1.3.6.1.4.1.1166.6.1.2.27.2.1.43
The value of this object provides the minimum value the Optical Power Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemaxValueOptPower		1.3.6.1.4.1.1166.6.1.2.27.2.1.44
The value of this object provides the maximum value the Optical Power Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmealarmStateOptPower		1.3.6.1.4.1.1166.6.1.2.27.2.1.45
The value of this object provides the curent alarm state of the Optical Power Analog parameter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), majorLowAlarm(2), minorLowAlarm(3), minorHighAlarm(4), majorHighAlarm(5), informational(6)

lmelabelLaserBias		1.3.6.1.4.1.1166.6.1.2.27.2.1.46
The value of this object provides the label of the Laser Bias Current Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeuomLaserBias		1.3.6.1.4.1.1166.6.1.2.27.2.1.47
The value of this object provides the Unit of Measure of the Laser Bias Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmemajorHighLaserBias		1.3.6.1.4.1.1166.6.1.2.27.2.1.48
The value of this object provides the Major High alarm value of the Laser Bias Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemajorLowLaserBias		1.3.6.1.4.1.1166.6.1.2.27.2.1.49
The value of this object provides the Major Low alarm value of the Laser Bias Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorHighLaserBias		1.3.6.1.4.1.1166.6.1.2.27.2.1.50
The value of this object provides the Minor High alarm value of the Laser Bias Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorLowLaserBias		1.3.6.1.4.1.1166.6.1.2.27.2.1.51
The value of this object provides the Minor Low alarm value of the Laser Bias Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmecurrentValueLaserBias		1.3.6.1.4.1.1166.6.1.2.27.2.1.52
The value of this object provides the Current value of the Laser Bias Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmestateFlagLaserBias		1.3.6.1.4.1.1166.6.1.2.27.2.1.53
The value of this object provides the state of the Laser Bias Analog parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmeminValueLaserBias		1.3.6.1.4.1.1166.6.1.2.27.2.1.54
The value of this object provides the minimum value the Laser Bias Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemaxValueLaserBias		1.3.6.1.4.1.1166.6.1.2.27.2.1.55
The value of this object provides the maximum value the Laser Bias Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmealarmStateLaserBias		1.3.6.1.4.1.1166.6.1.2.27.2.1.56
The value of this object provides the curent alarm state of the Laser Bias Analog parameter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), majorLowAlarm(2), minorLowAlarm(3), minorHighAlarm(4), majorHighAlarm(5), informational(6)

lmelabelTecCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.57
The value of this object provides the label of the TEC Current Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeuomTecCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.58
The value of this object provides the Unit of Measure of the TEC Current Analog parameter..
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmemajorHighTecCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.59
The value of this object provides the Major High alarm value of the TEC Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemajorLowTecCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.60
The value of this object provides the Major Low alarm value of the TEC Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorHighTecCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.61
The value of this object provides the Minor High alarm value of the TEC Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorLowTecCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.62
The value of this object provides the Minor Low alarm value of the TEC Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmecurrentValueTecCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.63
The value of this object provides the Current value of the TEC Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmestateFlagTecCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.64
The value of this object provides the state of the TEC Current Analog parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmeminValueTecCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.65
The value of this object provides the minimum value the TEC Current Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemaxValueTecCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.66
The value of this object provides the maximum value the TEC Current Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmealarmStateTecCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.67
The value of this object provides the curent alarm state of the TEC Current Analog parameter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), majorLowAlarm(2), minorLowAlarm(3), minorHighAlarm(4), majorHighAlarm(5), informational(6)

lmelabelLaserTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.68
The value of this object provides the label of the Laser Temperature Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeuomLaserTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.69
The value of this object provides the Unit of Measure of the Laser Temperature Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmemajorHighLaserTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.70
The value of this object provides the Major High alarm value of the Laser Temperature Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemajorLowLaserTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.71
The value of this object provides the Major Low alarm value of the Laser Temperature Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorHighLaserTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.72
The value of this object provides the Minor High alarm value of the Laser Temperature Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorLowLaserTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.73
The value of this object provides the Minor Low alarm value of the Laser Temperature Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmecurrentValueLaserTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.74
The value of this object provides the Current value of the Laser Temperature Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmestateFlagLaserTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.75
The value of this object provides the state of the Laser Temperature Analog parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmeminValueLaserTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.76
The value of this object provides the minimum value the Laser Temperature Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemaxValueLaserTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.77
The value of this object provides the maximum value the Laser Temperature Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmealarmStateLaserTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.78
The value of this object provides the curent alarm state of the Laser Temperature Analog parameter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), majorLowAlarm(2), minorLowAlarm(3), minorHighAlarm(4), majorHighAlarm(5), informational(6)

lmelabelModuleTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.79
The value of this object provides the label of the Module Temperature Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeuomModuleTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.80
The value of this object provides the Unit of Measure of the Module Temperature Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmemajorHighModuleTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.81
The value of this object provides the Major High alarm value of the Module Temperature Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemajorLowModuleTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.82
The value of this object provides the Major Low alarm value of the Module Temperature Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorHighModuleTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.83
The value of this object provides the Minor High alarm value of the Module Temperature Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorLowModuleTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.84
The value of this object provides the Minor Low alarm value of the Module Temperature Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmecurrentValueModuleTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.85
The value of this object provides the Current value of the Module Temperature Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmestateFlagModuleTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.86
The value of this object provides the state of the Module Temperature Analog parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmeminValueModuleTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.87
The value of this object provides the minimum value the Module Temperature Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemaxValueModuleTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.88
The value of this object provides the maximum value the Module Temperature Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmealarmStateModuleTemp		1.3.6.1.4.1.1166.6.1.2.27.2.1.89
The value of this object provides the curent alarm state of the Module Temperature Analog parameter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), majorLowAlarm(2), minorLowAlarm(3), minorHighAlarm(4), majorHighAlarm(5), informational(6)

lmelabelFanCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.90
The value of this object provides the label of the Fan Current Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeuomFanCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.91
The value of this object provides the Unit of Measure of the Fan Current Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmemajorHighFanCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.92
The value of this object provides the Major High alarm value of the Fan Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemajorLowFanCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.93
The value of this object provides the Major Low alarm value of the Fan Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorHighFanCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.94
The value of this object provides the Minor High alarm value of the Fan Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorLowFanCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.95
The value of this object provides the Minor Low alarm value of the Fan Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmecurrentValueFanCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.96
The value of this object provides the Current value of the Fan Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmestateFlagFanCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.97
The value of this object provides the state of the Fan Current Analog parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmeminValueFanCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.98
The value of this object provides the minimum value the Fan Current Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemaxValueFanCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.99
The value of this object provides the maximum value the Fan Current Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmealarmStateFanCurrent		1.3.6.1.4.1.1166.6.1.2.27.2.1.100
The value of this object provides the curent alarm state of the Fan Current Analog parameter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), majorLowAlarm(2), minorLowAlarm(3), minorHighAlarm(4), majorHighAlarm(5), informational(6)

lmelabel12Volt		1.3.6.1.4.1.1166.6.1.2.27.2.1.101
The value of this object provides the label of the 12v Current Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeuom12Volt		1.3.6.1.4.1.1166.6.1.2.27.2.1.102
The value of this object provides the Unit of Measure of the 12v Current Analog parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmemajorHigh12Volt		1.3.6.1.4.1.1166.6.1.2.27.2.1.103
The value of this object provides the Major High alarm value of the 12v Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemajorLow12Volt		1.3.6.1.4.1.1166.6.1.2.27.2.1.104
The value of this object provides the Major Low alarm value of the 12v Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorHigh12Volt		1.3.6.1.4.1.1166.6.1.2.27.2.1.105
The value of this object provides the Minor High alarm value of the 12v Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmeminorLow12Volt		1.3.6.1.4.1.1166.6.1.2.27.2.1.106
The value of this object provides the Minor Low alarm value of the 12v Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmecurrentValue12Volt		1.3.6.1.4.1.1166.6.1.2.27.2.1.107
The value of this object provides the Current value of the 12v Current Analog parameter. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmestateFlag12Volt		1.3.6.1.4.1.1166.6.1.2.27.2.1.108
The value of this object provides the state of the 12v Current Analog parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmeminValue12Volt		1.3.6.1.4.1.1166.6.1.2.27.2.1.109
The value of this object provides the minimum value the 12v Current Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmemaxValue12Volt		1.3.6.1.4.1.1166.6.1.2.27.2.1.110
The value of this object provides the maximum value the 12v Current Analog parameter can achive. This value is a floating point number that is represented as an IEEE 32 bit number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Float

lmealarmState12Volt		1.3.6.1.4.1.1166.6.1.2.27.2.1.111
The value of this object provides the curent alarm state of the 12v Current Analog parameter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), majorLowAlarm(2), minorLowAlarm(3), minorHighAlarm(4), majorHighAlarm(5), informational(6)

gx2lmeDigitalTableIndex		1.3.6.1.4.1.1166.6.1.2.27.3.2.1
The value of this object identifies the network element. This index is equal to the hfcCommonTableIndex for the same element.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4294967295

lmelabelRfInput		1.3.6.1.4.1.1166.6.1.2.27.3.2.2
The value of this object provides the label of the RF Input Control Digital parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeenumRfInput		1.3.6.1.4.1.1166.6.1.2.27.3.2.3
The value of this object represents the Enumeration values possible for the Digital parameter. Each Enumerated values is separated by a common. The first value has a enumerated value of 1.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueRfInput		1.3.6.1.4.1.1166.6.1.2.27.3.2.4
The value of this object is the current value of the parameter.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2)

lmestateflagRfInput		1.3.6.1.4.1.1166.6.1.2.27.3.2.5
The value of this object provides the state of the RF Input Control Digital parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmelabelOptOutput		1.3.6.1.4.1.1166.6.1.2.27.3.2.6
The value of this object provides the label of the Optical Output Control Digital parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeenumOptOutput		1.3.6.1.4.1.1166.6.1.2.27.3.2.7
The value of this object represents the Enumeration values possible for the Digital parameter. Each Enumerated values is separated by a common. The first value has a enumerated value of 1.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueOptOutput		1.3.6.1.4.1.1166.6.1.2.27.3.2.8
The value of this object is the current value of the parameter.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2)

lmestateflagOptOutput		1.3.6.1.4.1.1166.6.1.2.27.3.2.9
The value of this object provides the lmestate of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmelabelLaserMode		1.3.6.1.4.1.1166.6.1.2.27.3.2.10
The value of this object provides the label of the Laser Mode Digital parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeenumLaserMode		1.3.6.1.4.1.1166.6.1.2.27.3.2.11
The value of this object represents the Enumeration values possible for the Digital parameter. Each Enumerated values is separated by a common. The first value has a enumerated value of 1.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueLaserMode		1.3.6.1.4.1.1166.6.1.2.27.3.2.12
The value of this object is the current value of the parameter.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	preset(1), set(2), setEquate(3), manual(4), manualEquate(5)

lmestateflagLaserMode		1.3.6.1.4.1.1166.6.1.2.27.3.2.13
The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmelabelLaserSecMode		1.3.6.1.4.1.1166.6.1.2.27.3.2.14
The value of this object provides the label of the Laser Secondary Mode Digital parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeenumLaserSecMode		1.3.6.1.4.1.1166.6.1.2.27.3.2.15
The value of this object represents the Enumeration values possible for the Digital parameter. Each Enumerated values is separated by a common. The first value has a enumerated value of 1.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueLaserSecMode		1.3.6.1.4.1.1166.6.1.2.27.3.2.16
The value of this object is the current value of the parameter.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	cw(1), video(2)

lmestateflagLaserSecMode		1.3.6.1.4.1.1166.6.1.2.27.3.2.17
The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmelabelVideoOffset		1.3.6.1.4.1.1166.6.1.2.27.3.2.18
The value of this object provides the label of the Video Offset Digital parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeenumVideoOffset		1.3.6.1.4.1.1166.6.1.2.27.3.2.19
The value of this object represents the Enumeration values possible for the Digital parameter. Each Enumerated values is separated by a common. The first value has a enumerated value of 1..
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueVideoOffset		1.3.6.1.4.1.1166.6.1.2.27.3.2.20
The value of this object is the current value of the parameter.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	minus2dB(1), minus3dB(2), minus4dB(3), minus5dB(4)

lmestateflagVideoOffset		1.3.6.1.4.1.1166.6.1.2.27.3.2.21
The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmelabelFactoryDefault		1.3.6.1.4.1.1166.6.1.2.27.3.2.22
The value of this object provides the label of the Factory Default Reset Digital parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeenumFactoryDefault		1.3.6.1.4.1.1166.6.1.2.27.3.2.23
The value of this object represents the Enumeration values possible for the Digital parameter. Each Enumerated values is separated by a common. The first value has a enumerated value of 1.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueFactoryDefault		1.3.6.1.4.1.1166.6.1.2.27.3.2.24
The value of this object is the current value of the parameter.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2)

lmestateflagFactoryDefault		1.3.6.1.4.1.1166.6.1.2.27.3.2.25
The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmelabelFiberLength		1.3.6.1.4.1.1166.6.1.2.27.3.2.26
This object is only used for the LC1000 device family. The value of this object provides the label for the Fiber Length Digital parameter .
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeenumFiberLength		1.3.6.1.4.1.1166.6.1.2.27.3.2.27
This object is only used for the LC1000 device family. The value of this object represents the Enumeration values possible for the Digital parameter. The range for fiber length selection is from 6 to 25km, where 6km is represented with a 1 and 25 with a 19.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueFiberLength		1.3.6.1.4.1.1166.6.1.2.27.3.2.28
This object is only used for the LC1000 device family. The value of this object is the current value of the parameter. It is used to set fiber length. The value range for this object is: 0 to 30 Km.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	fl6km(1), fl7km(2), fl8km(3), fl9km(4), fl10km(5), fl11km(6), fl12km(7), fl13km(8), fl14km(9), fl15km(10), fl16km(11), fl17km(12), fl18km(13), fl19km(14), fl20km(15), fl21km(16), fl22km(17), fl23km(18), fl24km(19), fl25km(20)

lmestateflagFiberLength		1.3.6.1.4.1.1166.6.1.2.27.3.2.29
This object is only used for the LC1000 device family. The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmelabelConditioningUnit		1.3.6.1.4.1.1166.6.1.2.27.3.2.30
This object is only used for the LC1000 device family. The value of this object provides the label for the Conditioning Unit Digital parameter .
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeenumConditioningUnit		1.3.6.1.4.1.1166.6.1.2.27.3.2.31
This object is only used for the LC1000 device family. The value of this object represents the Enumeration values possible for the Digital parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueConditioningUnit		1.3.6.1.4.1.1166.6.1.2.27.3.2.32
This object is only used for the LC1000 device family. The value of this object is the current value of the parameter. It is used to normalize the output by -3db when a conditioning unit is being used in the system.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

lmestateflagConditioningUnit		1.3.6.1.4.1.1166.6.1.2.27.3.2.33
This object is only used for the LC1000 device family. The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

gx2lmeStatusTableIndex		1.3.6.1.4.1.1166.6.1.2.27.4.3.1
The value of this object identifies the network element. This index is equal to the hfcCommonTableIndex for the same element.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4294967295

lmelabelBoot		1.3.6.1.4.1.1166.6.1.2.27.4.3.2
The value of this object provides the label of the Boot Status Status parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueBoot		1.3.6.1.4.1.1166.6.1.2.27.4.3.3
The value of this object provides the current state of the parameter (0-Ok, 1-Undetermined 2-Warning, 3-Minor, 4-Major, 5-Critical).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), undetermined(2), warning(3), minor(4), major(5), critical(6)

lmestateflagBoot		1.3.6.1.4.1.1166.6.1.2.27.4.3.4
The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmelabelFlash		1.3.6.1.4.1.1166.6.1.2.27.4.3.5
The value of this object provides the label of the Flash Status Status parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueFlash		1.3.6.1.4.1.1166.6.1.2.27.4.3.6
The value of this object provides the current state of the parameter (0-Ok, 1-Undetermined 2-Warning, 3-Minor, 4-Major, 5-Critical).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), undetermined(2), warning(3), minor(4), major(5), critical(6)

lmestateflagFlash		1.3.6.1.4.1.1166.6.1.2.27.4.3.7
The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmelabelFactoryDataCRC		1.3.6.1.4.1.1166.6.1.2.27.4.3.8
The value of this object provides the label of the Factory Data CRC Status parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueFactoryDataCRC		1.3.6.1.4.1.1166.6.1.2.27.4.3.9
The value of this object provides the current state of the parameter (0-Ok, 1-Undetermined 2-Warning, 3-Minor, 4-Major, 5-Critical).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), undetermined(2), warning(3), minor(4), major(5), critical(6)

lmestateflagFactoryDataCRC		1.3.6.1.4.1.1166.6.1.2.27.4.3.10
The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmelabelLaserDataCRC		1.3.6.1.4.1.1166.6.1.2.27.4.3.11
The value of this object provides the label of the Laser Data CRC Status parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueLaserDataCRC		1.3.6.1.4.1.1166.6.1.2.27.4.3.12
The value of this object provides the current state of the parameter (0-Ok, 1-Undetermined 2-Warning, 3-Minor, 4-Major, 5-Critical).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), undetermined(2), warning(3), minor(4), major(5), critical(6)

lmestateflagLaserDataCRC		1.3.6.1.4.1.1166.6.1.2.27.4.3.13
The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmelabelAlarmDataCrc		1.3.6.1.4.1.1166.6.1.2.27.4.3.14
The value of this object provides the label of the Alarm Data Crc parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueAlarmDataCrc		1.3.6.1.4.1.1166.6.1.2.27.4.3.15
The value of this object provides the current state of the parameter (0-Ok, 1-Undetermined 2-Warning, 3-Minor, 4-Major, 5-Critical).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), undetermined(2), warning(3), minor(4), major(5), critical(6)

lmestateflagAlarmDataCrc		1.3.6.1.4.1.1166.6.1.2.27.4.3.16
The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmelabelHWStatus		1.3.6.1.4.1.1166.6.1.2.27.4.3.17
The value of this object provides the label of the Laser Drive Level Status parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueHWStatus		1.3.6.1.4.1.1166.6.1.2.27.4.3.18
The value of this object provides the current state of the parameter (0-Ok, 1-Undetermined 2-Warning, 3-Minor, 4-Major, 5-Critical).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), undetermined(2), warning(3), minor(4), major(5), critical(6)

lmestateflagHWStatus		1.3.6.1.4.1.1166.6.1.2.27.4.3.19
The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

lmelabelRFInputStatus		1.3.6.1.4.1.1166.6.1.2.27.4.3.20
The value of this object provides the label of the RF Input Status parameter.
Status: optional	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmevalueRFInputStatus		1.3.6.1.4.1.1166.6.1.2.27.4.3.21
The value of this object provides the current state of the parameter (0-Ok, 1-Undetermined 2-Warning, 3-Minor, 4-Major, 5-Critical).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), undetermined(2), warning(3), minor(4), major(5), critical(6)

lmestateflagRFInputStatus		1.3.6.1.4.1.1166.6.1.2.27.4.3.22
The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	hidden(1), read-only(2), updateable(3)

gx2lmeFactoryTableIndex		1.3.6.1.4.1.1166.6.1.2.27.5.4.1
The value of this object identifies the network element. This index is equal to the hfcCommonTableIndex for the same element.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4294967295

lmebootControlByteValue		1.3.6.1.4.1.1166.6.1.2.27.5.4.2
The value of this object indicates which bank the firmware is currently being boot from.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lmebootStatusByteValue		1.3.6.1.4.1.1166.6.1.2.27.5.4.3
This object indicates the status of the last boot
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lmebank1CRCValue		1.3.6.1.4.1.1166.6.1.2.27.5.4.4
This object provides the CRC code of bank 0.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lmebank2CRCValue		1.3.6.1.4.1.1166.6.1.2.27.5.4.5
This object provides the CRC code of bank 1.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lmeprgEEPROMByteValue		1.3.6.1.4.1.1166.6.1.2.27.5.4.6
This object indicates if the EEPROM has been programmed
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lmefactoryCRCValue		1.3.6.1.4.1.1166.6.1.2.27.5.4.7
This object provides the CRC code for the Factory data.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lmecalculateCRCValue		1.3.6.1.4.1.1166.6.1.2.27.5.4.8
This object indicates which of the Emnums will have the CRC calculated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	factory(1), laserData(2), alarm(3)

lmehourMeterValue		1.3.6.1.4.1.1166.6.1.2.27.5.4.9
This object provides the hour meter reading of the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lmeflashPrgCntAValue		1.3.6.1.4.1.1166.6.1.2.27.5.4.10
This object provides the number of times Bank 1 flash has been programmed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lmeflashPrgCntBValue		1.3.6.1.4.1.1166.6.1.2.27.5.4.11
This object provides the number of times Bank 1 flash has been programmed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

lmeflashBankARevValue		1.3.6.1.4.1.1166.6.1.2.27.5.4.12
This object provides the revision of flash bank 0.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

lmeflashBankBRevValue		1.3.6.1.4.1.1166.6.1.2.27.5.4.13
This object provides the revision of flash bank 1.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

gx2Lm1000EHoldTimeTableIndex		1.3.6.1.4.1.1166.6.1.2.27.6.5.1
The value of this object is the index of the data object.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4294967295

gx2Lm1000EHoldTimeSpecIndex		1.3.6.1.4.1.1166.6.1.2.27.6.5.2
The value of this object identifies the index of the alarm object to be modified.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4294967295

gx2Lm1000EHoldTimeData		1.3.6.1.4.1.1166.6.1.2.27.6.5.3
The value of this object provides access to the hold timers used to suppress nose on analog objects. This object is a 32 bit object. Validation data is entered into bytes zero and one of the object. Bytes three and four are used to entering the hold time for the specified alarm object. The Hold timer data ranges from 0 to 1300 seconds. The index of this object corresponds to the alarm object to be modified. Alarm Hold timers correspond to the index of this object as follows: Index 1 = xxx, index 2 = xxxx, Index 3 = xxxx, The hold time is represented in seconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

trapLMEConfigChangeInteger		1
This trap is issued if configuration of a single variable with integer type was changed (via ANY interface). TrapChangedValueInteger variable may contain current reading of that variable. trapPerceivedSeverity - 'indeterminate'
TRAP-TYPE

trapLMEConfigChangeDisplayString		2
This trap is issued if configuration of a single variable with DispalayString type was changed (via ANY interface). TrapChangedValueDisplayString variable may contain current reading of that variable. trapPerceivedSeverity - 'indeterminate'
TRAP-TYPE

trapLMERFInputAlarm		3
This trap is issued when the Laser Modules RF input parameter goes out of range. trapAdditionalInfoInteger variable contains current reading of the this parameter.
TRAP-TYPE

trapLMERFOverloadAlarm		4
This trap is issued when the Laser Modules RF overload parameter goes out of range. trapAdditionalInfoInteger variable contains current reading of the this parameter.
TRAP-TYPE

trapLMERFOffsetAlarm		5
This trap is issued when the Laser Modules RF Offset parameter goes out of range. trapAdditionalInfoInteger variable contains current reading of the this parameter.
TRAP-TYPE

trapLMEOpticalPowerAlarm		6
This trap is issued when the Laser Modules Optical Power parameter goes out of range. trapAdditionalInfoInteger variable contains current reading of the this parameter.
TRAP-TYPE

trapLMELaserBiasAlarm		7
This trap is issued when the Laser Bias parameter goes out of range. trapAdditionalInfoInteger variable contains current reading of the this parameter.
TRAP-TYPE

trapLMELaserTempAlarm		8
This trap is issued when the Laser Temperature parameter goes out of range. trapAdditionalInfoInteger variable contains current reading of the this parameter.
TRAP-TYPE

trapLMETECCurrentAlarm		9
This trap is issued when the Laser Modules TEC Current parameter goes out of range. trapAdditionalInfoInteger variable contains current reading of the this parameter.
TRAP-TYPE

trapLMEFanCurrentAlarm		10
This trap is issued when the Laser Modules Fan Current parameter goes out of range. trapAdditionalInfoInteger variable contains current reading of the this parameter.
TRAP-TYPE

trapLME12vAlarm		11
This trap is issued when the Laser Modules 12 Volt parameter goes out of range. trapAdditionalInfoInteger variable contains current reading of the this parameter.
TRAP-TYPE

trapLMEModuleTempAlarm		12
This trap is issued when the Laser Module Temperature goes out of range.
TRAP-TYPE

trapLMEFlashAlarm		13
This trap is issued when the Laser Modules detects an error during Flash memory operations.
TRAP-TYPE

trapLMELaserBiasCntLoopAlarm		14
This trap is issued when the Laser Modules detects an error in its Laser Bias control loop operation.
TRAP-TYPE

trapLMEBankBootAlarm		15
This trap is issued when the Laser Modules detects an error while booting from bank 0 or bank 1.
TRAP-TYPE

trapLMELaserBiasCntLoopInitAlarm		16
This trap is issued when the Laser Bias Control loop init fails.
TRAP-TYPE

trapLMERFParamInitAlarm		17
This trap is issued when the RF parameter Init fails.
TRAP-TYPE

trapLMETECParamInitAlarm		18
This trap is issued when the TEC Parameter Init fails.
TRAP-TYPE

trapLMEAttnTableInitAlarm		19
This trap is issued when the Attenuator Table Init fails.
TRAP-TYPE

trapLMEPowerMeterTableInitAlarm		20
This trap is issued when the Power Meter Table Init fails.
TRAP-TYPE

trapLMELaserDataCRCAlarm		21
This trap is issued when the Laser Data CRC is incorrect.
TRAP-TYPE

trapLMEAlarmDataCRCAlarm		22
This trap is issued when the Alarm Data CRC is incorrect.
TRAP-TYPE

trapLMEFactoryDataCRCAlarm		23
This trap is issued when the Factory Data CRC is incorrect.
TRAP-TYPE

trapLMEUserRFOffAlarm		24
This trap is issued when the the User RF is turned off.
TRAP-TYPE

trapLMEUserOpticalOffAlarm		25
This trap is issued when the User Optical Power is turned off.
TRAP-TYPE

trapLMEResetFactoryDefaultAlarm		26
This trap is issued when the Factory Default Reset occurs.
TRAP-TYPE