ONS15501-MIB
File:
ONS15501-MIB.mib (43406 bytes)
Imported modules
Imported symbols
Defined Types
Ons15501ImageDnLoadStatus |
|
The operational states for software image download.
This enumerates all possible failure conditions. |
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
notInitiated(1), inProgress(2), failedUnknownErr(3), failedFileNotFound(4), failedAccessDenied(5), failedTimedOut(6), completedSuccessfully(7), failedInDownload(8), failedTimeoutInDownload(9), failedToConnectToServer(10), failedWhileWritingToFlash(11), failedIllegalOperation(12), failedFileExists(13), failedUnknownTransferId(14), failedUnknownUser(15) |
|
Ons15501AdminStatus |
|
The Administrative state for a configured object. |
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
disabled(1), enabled(2) |
|
Ons15501NTPStatus |
|
The operational state for NTP client.
It may be 'unknown' if the NTP client has just started. |
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
disabled(1), bothServersBad(2), usingPrimary(3), usingSecondary(4), unknown(5) |
|
Ons15501TenthVolt |
|
This data type represents voltage levels that are normally
expressed in volts. Units are in tenths of a volt;
for example, -48.1 volts will be represented as -481. |
TEXTUAL-CONVENTION |
|
|
|
|
Integer32 |
-1000..0 |
|
Ons15501TenthdB |
|
This data type represents power levels (or power gain)
that are normally expressed in dBm (dB). Units are in
tenths of a dBm (db);
for example, -5.1 dB will be represented as -51 |
TEXTUAL-CONVENTION |
|
|
|
|
Integer32 |
-1000..500 |
|
Ons15501TenthCentigrade |
|
This data type represents temperature values that
are normally expressed in Centigrade. Units are in
tenths of a Centigrade;
for example, -5.1 Centigrade will be represented as -51. |
TEXTUAL-CONVENTION |
|
|
|
|
Integer32 |
-500..1000 |
|
Ons15501AlarmStatus |
|
Represents a alarm level |
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
critical(1), major(2), minor(3), info(4), noAlarm(5) |
|
Ons15501TrapTypeEnumeration |
|
This provides the details on type of alarm
none
- No exception
unacceptableAmbientTemperature,
- the temperature measured by thermal sensor
shows value outside the operational limits.
unacceptableElectricalPower,
- the measured power supply level(s) are not
within range.
inputSignalPowerTooLow,
- the measured input signal power is not
within range.
unacceptableOutputSignalPower,
- the measured output signal power is not
within range.
embeddedControllerCommFailure,
- the communication with embedded controller
has failed.
softwareUpgradeInitiated,
- a TFTP/FTP request has been launched
softwareUpgradeFailed,
- a TFTP/FTP request that was launched has failed
softwareUpgradeCompleted,
- a TFTP/FTP request that was launched has completed
softwareRebootInitiated,
- a reboot has been requested on the unit
softwareRolledBack,
- the unit has booted from a bank that is not
the programmed bank. This is possibly because the
image from programmed bank was bad or because
the boot loader was explicitly asked to boot from
another bank (using the console).
configurationChanged,
- a writeable attribute has been modified (through
any of the management interface exposed by the
system - e.g. CLI. SNMP etc.)
unacceptableGain,
- equipment is unable to achieve the planned level
for gain.
laserPumpBad,
- the measured parameters for the laser show that
a laser pump has gone bad.
eEPROMBad,
- the writes / reads from EEPROM have problems.
|
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
unacceptableAmbientTemperature(1), unacceptableElectricalPower(2), inputSignalPowerTooLow(3), unacceptableOutputSignalPower(4), embeddedControllerCommFailure(5), softwareUpgradeInitiated(6), softwareUpgradeFailed(7), softwareUpgradeCompleted(8), softwareRebootInitiated(9), softwareRolledBack(10), configurationChanged(11), unacceptableGain(12), laserPumpBad(13), eEPROMBad(14), unknown(32767) |
|
Ons15501TrapLogEntry |
|
SEQUENCE |
|
|
|
|
ons15501TrapLogEntryIndex |
Unsigned32 |
|
|
ons15501TrapLogEntryTrapType |
Ons15501TrapTypeEnumeration |
|
|
ons15501TrapLogEntryDirection |
Ons15501TrapDirectionEnumeration |
|
|
ons15501TrapLogEntryTimeStamp |
TimeStamp |
|
|
ons15501TrapLogEntryDateAndTime |
DateAndTime |
|
|
ons15501TrapLogEntryPhyIndex |
PhysicalIndex |
|
|
ons15501TrapLogEntrySeverity |
Ons15501AlarmStatus |
|
Ons15501ActiveAlarmEntry |
|
SEQUENCE |
|
|
|
|
ons15501ActAlarmType |
Ons15501TrapTypeEnumeration |
|
|
ons15501ActAlarmTimeStamp |
TimeStamp |
|
|
ons15501ActAlarmDateAndTime |
DateAndTime |
|
|
ons15501ActAlarmPhyIndex |
PhysicalIndex |
|
|
ons15501ActAlarmSeverity |
Ons15501AlarmStatus |
|
Defined Values
ons15501MIB |
1.3.6.1.4.1.1869.11.11 |
The MIB definitions for ONS-15501 Optical
Amplifier. |
MODULE-IDENTITY |
|
|
|
synEmbLx |
1.3.6.1.4.1.1869.11 |
OBJECT IDENTIFIER |
|
|
|
ons15501SysSwDownload |
1.3.6.1.4.1.1869.11.11.1.4 |
Used to control the image download to the flash banks.
NOTE: Read on this attribute returns the last t/ftp command,
without login/password.
For s/w release 4.0 and above, the value read back
includes the Kilo-Bytes downloaded for last download
command.
It is the size of file downloaded (in KB), if the
download has completed. If a download is in progress
this value would correspond to Kilo-Bytes successfully
downloaded so far.
For set the string syntax is one of the following
a. abort
- Aborts the current download
b. ftp::::::[:passive]
- Download image using ftp
c. tftp:::
- Download image using tftp
where
- is t/ftp server name
- is login to be used for ftp (default anonymous)
- password for the login name for ftp
(default - no passwd - passwd is empty string)
- path to be given on ftp prompt for cd
(default - skip cd command )
- name of the file to be downloaded and burnt
to the flash - NO DEFAULTS - because the
filename is used as distinguishing versions
there are no defaults for this command.
For TFTP Path information is part of the filename
- which flash has to be burnt [1|2|3]
NOTE: Burn to active bank fails
passive - if `passive` is specified, ftp is done using
passive mode (provided for FTP download across
firewall).
NOTE: None of the fields should contain ':' within them, as
it is used as field separator. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
|
|
ons15501SysDevActiveImage |
1.3.6.1.4.1.1869.11.11.1.5 |
Show currently active image's bank number.
This may be different from ons15501SysConfiguredActiveImage,
if
a. The image on ons15501SysConfiguredActiveImage did not
boot properly.
b. User chose another bank during bootup, using the
serial console port.
|
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
1..3 |
|
ons15501SysDeviceManagerList |
1.3.6.1.4.1.1869.11.11.1.6 |
A ',' separated list of managers that will receive the
Traps.
If a specific host should receive the traps sent from this
unit, it should be added to the list using CLI.
Up to 16 managers can be present in this list. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
|
|
ons15501CLEICode |
1.3.6.1.4.1.1869.11.11.1.9 |
This attribute represents the CLEI (Common Language
Equipment Identifier) code for the ONS15501. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
|
|
ons15501PrimaryNTP |
1.3.6.1.4.1.1869.11.11.1.10 |
The IP address for the primary NTP server. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
ons15501SecondaryNTP |
1.3.6.1.4.1.1869.11.11.1.11 |
The IP address for the secondary NTP server. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
ons15501ActiveSoftwareVer |
1.3.6.1.4.1.1869.11.11.1.14 |
This attribute provides the active software version.
This will be same as the entPhysicalSoftwareRev for
the entry corresponding to the chassis. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
|
|
ons15501LastConfigChangeTime |
1.3.6.1.4.1.1869.11.11.1.15 |
The value of sysUpTime when last configuration
change was done.
NMS may use this information to synchronize if
some configuration has changed on the unit. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TimeStamp |
|
|
ons15501InRemoteInfoUpdateTime |
1.3.6.1.4.1.1869.11.11.1.16 |
This attribute gives the time-stamp when one or more of
ons15501InRemoteChassisName, ons15501InRemotePortName,
or ons15501InRemoteAgentIpAddr was changed.
NMS may use this information to find the latest
information if data from remote unit does not match
that of this unit. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TimeStamp |
|
|
ons15501InRemoteChassisName |
1.3.6.1.4.1.1869.11.11.1.17 |
Manager initialized string value to identify the
chassis associated with remote connection for
optical input.
ons15501InRemoteChassisName would be a ZERO length
string if the input link is disabled.
To disable the input link details set
ons15501InRemoteChassisName to ZERO length string
and ons15501InRemoteAgentIpAddr to 0.0.0.0. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
|
|
ons15501InRemotePortName |
1.3.6.1.4.1.1869.11.11.1.18 |
Manager initialized string value to identify the
the port (on remote chassis) associated with remote
connection for optical input.
ons15501InRemotePortName would be a ZERO length
string if the input link is disabled.
To disable the input link details set
ons15501InRemoteChassisName to ZERO length string
and ons15501InRemoteAgentIpAddr to 0.0.0.0. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
|
|
ons15501InRemoteAgentIpAddr |
1.3.6.1.4.1.1869.11.11.1.19 |
Manager initialized string value to identify the
network address to be used to reach the SNMP agent
entity containing information about the port and chassis
providing optical input.
ons15501InRemoteAgentIpAddr would be a 0.0.0.0
if the input link is disabled.
To disable the input link entry set
ons15501InRemoteChassisName to ZERO length string
and ons15501InRemoteAgentIpAddr to 0.0.0.0. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
ons15501OutRemoteInfoUpdateTime |
1.3.6.1.4.1.1869.11.11.1.20 |
This attribute gives the time-stamp when one or more of
ons15501OutRemoteChassisName, ons15501OutRemotePortName,
or ons15501OutRemoteAgentIpAddr was changed.
NMS may use this information to find the latest
information if data from remote unit does not match
that of this unit. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TimeStamp |
|
|
ons15501OutRemoteChassisName |
1.3.6.1.4.1.1869.11.11.1.21 |
Manager initialized string value to identify the
chassis associated with remote connection for
optical output.
ons15501OutRemoteChassisName would be a ZERO length
string if the output link is disabled.
To disable the output link details set
ons15501OutRemoteChassisName to ZERO length string
and ons15501OutRemoteAgentIpAddr to 0.0.0.0. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
|
|
ons15501OutRemotePortName |
1.3.6.1.4.1.1869.11.11.1.22 |
Manager initialized string value to identify the
the port (on remote chassis) associated with remote
connection for optical output.
ons15501OutRemotePortName would be a ZERO length
string if the output link is disabled.
To disable the output link details set
ons15501OutRemoteChassisName to ZERO length string
and ons15501OutRemoteAgentIpAddr to 0.0.0.0. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
|
|
ons15501OutRemoteAgentIpAddr |
1.3.6.1.4.1.1869.11.11.1.23 |
Manager initialized string value to identify the
network address to be used to reach the SNMP agent
entity containing information about the port and chassis
using optical output.
ons15501OutRemoteAgentIpAddr would be a 0.0.0.0
if the output link is disabled.
To disable the output link entry set
ons15501OutRemoteChassisName to ZERO length string
and ons15501OutRemoteAgentIpAddr to 0.0.0.0. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
ons15501SysDateAndTime |
1.3.6.1.4.1.1869.11.11.1.25 |
The date and time of the System.
The write will not succeed if the administrative
state for NTP (ons15501NTPAdminStatus)
is 'enabled'.
Setting this attribute will autmatically change
values for ons15501TrapLogEntryDateAndTime and
ons15501ActAlarmDateAndTime. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DateAndTime |
|
|
ons15501LastTrapIndex |
1.3.6.1.4.1.1869.11.11.3.1 |
The value of ons15501TrapLogEntryIndex, used while logging
the most recent trap. Goes back to 1, after reaching
the max value.
The trap log table is a circular list with the most
recent entry at index given by this attribute.
On restart of the unit, the value is reset to 1. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
1..32767 |
|
ons15501TrapLogTable |
1.3.6.1.4.1.1869.11.11.3.2 |
Table for last N traps (N = 100 in most cases).
Please refer to ons15501LastTrapIndex for
details on how this table is organized. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
Ons15501TrapLogEntry |
|
ons15501TrapLogEntry |
1.3.6.1.4.1.1869.11.11.3.2.1 |
Entry for a trap |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
Ons15501TrapLogEntry |
|
|
ons15501TrapLogEntryIndex |
1.3.6.1.4.1.1869.11.11.3.2.1.1 |
index field for this entry. Actual range at
run time is ons15501TrapCounter to
ons15501TrapCounter - N + 1 or 1
(whichever is higher) |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
1..32767 |
|
ons15501TrapLogEntryTrapType |
1.3.6.1.4.1.1869.11.11.3.2.1.2 |
The type of trap. See the definition
of Ons15501TrapTypeEnumeration for possible values. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Ons15501TrapTypeEnumeration |
|
|
ons15501TrapLogEntryDirection |
1.3.6.1.4.1.1869.11.11.3.2.1.3 |
Whether the trap is being asserted or cleared.
Please note that some traps don't have a direction.
(e.g. configuration changed). |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Ons15501TrapDirectionEnumeration |
|
|
ons15501TrapLogEntryTimeStamp |
1.3.6.1.4.1.1869.11.11.3.2.1.4 |
The value of sysUpTime when the entry was placed in
the log. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TimeStamp |
|
|
ons15501TrapLogEntryDateAndTime |
1.3.6.1.4.1.1869.11.11.3.2.1.5 |
The local date and time at which the entry was placed in
the log. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DateAndTime |
|
|
ons15501TrapLogEntryPhyIndex |
1.3.6.1.4.1.1869.11.11.3.2.1.6 |
Provides entPhysicalIndex value for the physical entity
corresponding to the trap entry. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
PhysicalIndex |
|
|
ons15501TrapLogEntrySeverity |
1.3.6.1.4.1.1869.11.11.3.2.1.7 |
Provides the severity level corresponding to this
trap entry. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Ons15501AlarmStatus |
|
|
ons15501ActiveAlarmTable |
1.3.6.1.4.1.1869.11.11.3.3 |
Table for currently active alarm conditions.
This table is effectively the list of traps
that have been asserted but not cleared. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
Ons15501ActiveAlarmEntry |
|
ons15501ActiveAlarmEntry |
1.3.6.1.4.1.1869.11.11.3.3.1 |
Entry for an active alarm condition.
For each alarm condition present on the
equipment, there would be an entry in
the table. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
Ons15501ActiveAlarmEntry |
|
|
ons15501ActAlarmType |
1.3.6.1.4.1.1869.11.11.3.3.1.1 |
Index field for ons15501ActiveAlarmTable.
Presence of an entry implies that the specific
alarm type is active on the unit. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
Ons15501TrapTypeEnumeration |
|
|
ons15501ActAlarmPhyIndex |
1.3.6.1.4.1.1869.11.11.3.3.1.4 |
Provides entPhysicalIndex value for the physical entity
corresponding to the alarm entry. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
PhysicalIndex |
|
|
ons15501TrapDescriptionEntry |
1.3.6.1.4.1.1869.11.11.3.4.1 |
Entry for textual information about traps. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
Ons15501TrapDescriptionEntry |
|
|
ons15501TrapDescription |
1.3.6.1.4.1.1869.11.11.3.4.1.2 |
The textual information corresponding to the
ons15501TrapTypeValue. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
|
|
ons15501TrapSeverity |
1.3.6.1.4.1.1869.11.11.3.4.1.3 |
Provides the default severity level corresponding
to the ons15501TrapTypeValue. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Ons15501AlarmStatus |
|
|
ons15501GenericNotificationTrap |
1.3.6.1.4.1.1869.11.11.4.0.1 |
This notification is generated whenever a bitmap change is
observed on any of the monitored equipment, or when a change
has to be notified. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
ons15501OutputSignalPower |
1.3.6.1.4.1.1869.11.11.2.5 |
The optical signal power at the output of the Amplifier.
The value of this attribute triggers the alarm, based on
mean value and trigger as defined by
ons15501OutputSignalPowerMean and
ons15501OutputSignalPowerTrigger.
This value is internally calculated using the following
formula.
ons15501OutputSignalPower = ons15501OpticalPowerGain +
ons15501InputOpticalPower
At very low ons15501InputOpticalPower (below -16 dBm),
the ons15501OutputSignalPower has significant difference
from ons15501OutputOpticalPower while at higher input
power (ons15501InputOpticalPower) they are closer.
Following graph captures the difference (for a 17 dBm
EDFA)
(dashes '-'/'_' denote optical output power
while dots '.' denote signal output power)
^
| .-
| .-
| .-
+5 dBm | .-
| .-
Optical | _.-
power / | _ -.
Signal |_ _ - .
power | .
| .
| .
-17 dBm +-----------------------+-------------->
-29 dBm -10 dBm
Input Optical Power
|
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Ons15501TenthdB |
|
|
ons15501OutputSignalPowerMean |
1.3.6.1.4.1.1869.11.11.2.6 |
Mean value for output optical power.
If the output signal power falls below (or goes
above) the mean value by more than trigger
(see ons15501OutputSignalPowerTrigger) an alarm
is generated. The alarm is cleared when the
output optical power is back within 90% of trigger
from the mean. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Ons15501TenthdB |
-60..0 |
|
ons15501OutputSignalPowerTrigger |
1.3.6.1.4.1.1869.11.11.2.7 |
Trigger defines the max deviation allowed from the
mean, without an alarm being generated. Once an
alarm is generated, it is not cleared until the
output signal power falls back within 90% of the
trigger value from the mean. Please also refer
to ons15501OutputSignalPowerMean above. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Ons15501TenthdB |
0..180 |
|
ons15501OpticalPowerGain |
1.3.6.1.4.1.1869.11.11.2.9 |
The measured value for power gain.
This value does not include the amplification
noise that is significant for low input signals. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Ons15501TenthdB |
|
|
ons15501GainTrigger |
1.3.6.1.4.1.1869.11.11.2.10 |
The gain deviation allowed from the configured gain
before an alarm is asserted. The alarm is not cleared,
until measured gain(ons15501OpticalPowerGain) is back
within 90% of ons15501GainTrigger from configured gain
(ons15501ConfigOpticalGain). |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Ons15501TenthdB |
0..20 |
|
ons15501PowerSupply1Level |
1.3.6.1.4.1.1869.11.11.2.11 |
The voltage fed through power supply 1.
The value of the attribute is 10 times the
the value in volts. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Ons15501TenthVolt |
|
|
ons15501PowerSupply2Level |
1.3.6.1.4.1.1869.11.11.2.12 |
The voltage fed through power supply 2.
The value of the attribute is 10 times the
the value in volts. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Ons15501TenthVolt |
|
|
ons15501DevAmbTempMean |
1.3.6.1.4.1.1869.11.11.2.15 |
Mean value for temperature.
If the temperature falls below (or goes above) the
mean value by more than trigger level (see
ons15501DevAmbTempTrigger) an alarm is generated.
The alarm is cleared when the temperature is back
within 90% of trigger value, from the mean. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Ons15501TenthCentigrade |
200..400 |
|
ons15501DevAmbTempTrigger |
1.3.6.1.4.1.1869.11.11.2.16 |
Please refer to ons15501DevAmbTempMean above.
Trigger defines the max deviation allowed from the
mean, without an alarm being generated. Once an
alarm is generated, it is not cleared until the
temperature falls back within 90% of the value. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Ons15501TenthCentigrade |
200..300 |
|
ons15501FinalCompliance |
1.3.6.1.4.1.1869.11.11.6.1.1 |
The compliance statement for final release ONS15501. |
Status: deprecated |
Access: read-only |
MODULE-COMPLIANCE |
|
|
|
ons15501Rel4Compliance |
1.3.6.1.4.1.1869.11.11.6.1.2 |
The compliance statement for 4.0 release ONS15501. |
Status: current |
Access: read-only |
MODULE-COMPLIANCE |
|
|
|
ons15501SysInfoGroup |
1.3.6.1.4.1.1869.11.11.6.2.1 |
The basic group defines objects which are common to all
Embedded Linux product series of Synchronous equipment. |
Status: deprecated |
Access: read-only |
OBJECT-GROUP |
|
|
|
ons15501TrapLogGroup |
1.3.6.1.4.1.1869.11.11.6.2.2 |
The trap attribute group provides the trap logs.
These attributes are also used in trap notifications. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|
ons15501ActiveAlarmGroup |
1.3.6.1.4.1.1869.11.11.6.2.3 |
The alarm attribute group provides the list of active
alarms |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|
ons15501TrapDescriptionGroup |
1.3.6.1.4.1.1869.11.11.6.2.4 |
The trap description attribute group provides the
mapping from trap type to textual information about
the trap. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|
ons15501FinalAttrGroup |
1.3.6.1.4.1.1869.11.11.6.2.5 |
The ons15501 group of attributes models the parameters
in the EDFA. |
Status: deprecated |
Access: read-only |
OBJECT-GROUP |
|
|
|
ons15501FinalNotificationsGroup |
1.3.6.1.4.1.1869.11.11.6.2.6 |
The notification that carries all the exception
information. |
Status: current |
Access: read-only |
NOTIFICATION-GROUP |
|
|
|
ons15501CoreAttrGroup |
1.3.6.1.4.1.1869.11.11.6.2.7 |
The ons15501 group of attributes models the parameters
in the EDFA. The power supply related attributes are
not part of this group. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|
ons15501PowerSupplyStatusGroup |
1.3.6.1.4.1.1869.11.11.6.2.8 |
The ons15501 group of attributes models the status
of power supplies. The support for status was introduced
in version 4.0. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|
ons15501PowerSupplyLevelGroup |
1.3.6.1.4.1.1869.11.11.6.2.9 |
The ons15501 group of attributes provides the
voltage level of power supplies. It is available only
for DC series of ONS15501. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|
ons15501SysInfoGroup2 |
1.3.6.1.4.1.1869.11.11.6.2.10 |
The basic group defines objects which are common to all
Embedded Linux product series of Synchronous equipment. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|