OPT-IF-MIB

File: OPT-IF-MIB.mib (223203 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMP-FRAMEWORK-MIB
SNMPv2-CONF IF-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Gauge32
Integer32 Unsigned32 transmission
TEXTUAL-CONVENTION RowPointer RowStatus
TruthValue SnmpAdminString MODULE-COMPLIANCE
OBJECT-GROUP ifIndex

Defined Types

OptIfAcTI  
The trace identifier (TI) accepted at the receiver.
TEXTUAL-CONVENTION    
  OCTET STRING Size(64)  

OptIfBitRateK  
Indicates the index 'k' that is used to represent a supported bit rate and the different versions of OPUk, ODUk and OTUk. Allowed values of k are defined in ITU-T G.709. Currently allowed values in G.709 are: k=1 represents an approximate bit rate of 2.5 Gbit/s, k=2 represents an approximate bit rate of 10 Gbit/s, k=3 represents an approximate bit rate of 40 Gbit/s.
TEXTUAL-CONVENTION    
  Integer32  

OptIfDEGM  
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if OptIfDEGM consecutive bad PM Seconds are detected.
TEXTUAL-CONVENTION    
  Unsigned32 2..10  

OptIfDEGThr  
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to OptIfDEGThr.
TEXTUAL-CONVENTION    
  Unsigned32 1..100  

OptIfDirectionality  
Indicates the directionality of an entity.
TEXTUAL-CONVENTION    
  INTEGER sink(1), source(2), bidirectional(3)  

OptIfSinkOrSource  
Indicates the directionality of an entity that is allowed only to be a source or sink.
TEXTUAL-CONVENTION    
  INTEGER sink(1), source(2)  

OptIfExDAPI  
The Destination Access Point Identifier (DAPI) expected by the receiver.
TEXTUAL-CONVENTION    
  OCTET STRING Size(16)  

OptIfExSAPI  
The Source Access Point Identifier (SAPI) expected by the receiver.
TEXTUAL-CONVENTION    
  OCTET STRING Size(16)  

OptIfIntervalNumber  
Uniquely identifies a 15-minute interval. The interval identified by 1 is the most recently completed interval, and the interval identified by n is the interval immediately preceding the one identified by n-1.
TEXTUAL-CONVENTION    
  Unsigned32 1..96  

OptIfTIMDetMode  
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function.
TEXTUAL-CONVENTION    
  INTEGER off(1), dapi(2), sapi(3), both(4)  

OptIfTxTI  
The trace identifier (TI) transmitted.
TEXTUAL-CONVENTION    
  OCTET STRING Size(64)  

OptIfOTMnEntry  
SEQUENCE    
  optIfOTMnOrder Unsigned32
  optIfOTMnReduced TruthValue
  optIfOTMnBitRates BITS
  optIfOTMnInterfaceType SnmpAdminString
  optIfOTMnTcmMax Unsigned32
  optIfOTMnOpticalReach INTEGER

OptIfPerfMonIntervalEntry  
SEQUENCE    
  optIfPerfMonCurrentTimeElapsed Gauge32
  optIfPerfMonCurDayTimeElapsed Gauge32
  optIfPerfMonIntervalNumIntervals Unsigned32
  optIfPerfMonIntervalNumInvalidIntervals Unsigned32

OptIfOTSnConfigEntry  
SEQUENCE    
  optIfOTSnDirectionality OptIfDirectionality
  optIfOTSnAprStatus SnmpAdminString
  optIfOTSnAprControl SnmpAdminString
  optIfOTSnTraceIdentifierTransmitted OptIfTxTI
  optIfOTSnDAPIExpected OptIfExDAPI
  optIfOTSnSAPIExpected OptIfExSAPI
  optIfOTSnTraceIdentifierAccepted OptIfAcTI
  optIfOTSnTIMDetMode OptIfTIMDetMode
  optIfOTSnTIMActEnabled TruthValue
  optIfOTSnCurrentStatus BITS

OptIfOTSnSinkCurrentEntry  
SEQUENCE    
  optIfOTSnSinkCurrentSuspectedFlag TruthValue
  optIfOTSnSinkCurrentInputPower Integer32
  optIfOTSnSinkCurrentLowInputPower Integer32
  optIfOTSnSinkCurrentHighInputPower Integer32
  optIfOTSnSinkCurrentLowerInputPowerThreshold Integer32
  optIfOTSnSinkCurrentUpperInputPowerThreshold Integer32
  optIfOTSnSinkCurrentOutputPower Integer32
  optIfOTSnSinkCurrentLowOutputPower Integer32
  optIfOTSnSinkCurrentHighOutputPower Integer32
  optIfOTSnSinkCurrentLowerOutputPowerThreshold Integer32
  optIfOTSnSinkCurrentUpperOutputPowerThreshold Integer32

OptIfOTSnSinkIntervalEntry  
SEQUENCE    
  optIfOTSnSinkIntervalNumber OptIfIntervalNumber
  optIfOTSnSinkIntervalSuspectedFlag TruthValue
  optIfOTSnSinkIntervalLastInputPower Integer32
  optIfOTSnSinkIntervalLowInputPower Integer32
  optIfOTSnSinkIntervalHighInputPower Integer32
  optIfOTSnSinkIntervalLastOutputPower Integer32
  optIfOTSnSinkIntervalLowOutputPower Integer32
  optIfOTSnSinkIntervalHighOutputPower Integer32

OptIfOTSnSinkCurDayEntry  
SEQUENCE    
  optIfOTSnSinkCurDaySuspectedFlag TruthValue
  optIfOTSnSinkCurDayLowInputPower Integer32
  optIfOTSnSinkCurDayHighInputPower Integer32
  optIfOTSnSinkCurDayLowOutputPower Integer32
  optIfOTSnSinkCurDayHighOutputPower Integer32

OptIfOTSnSinkPrevDayEntry  
SEQUENCE    
  optIfOTSnSinkPrevDaySuspectedFlag TruthValue
  optIfOTSnSinkPrevDayLastInputPower Integer32
  optIfOTSnSinkPrevDayLowInputPower Integer32
  optIfOTSnSinkPrevDayHighInputPower Integer32
  optIfOTSnSinkPrevDayLastOutputPower Integer32
  optIfOTSnSinkPrevDayLowOutputPower Integer32
  optIfOTSnSinkPrevDayHighOutputPower Integer32

OptIfOTSnSrcCurrentEntry  
SEQUENCE    
  optIfOTSnSrcCurrentSuspectedFlag TruthValue
  optIfOTSnSrcCurrentOutputPower Integer32
  optIfOTSnSrcCurrentLowOutputPower Integer32
  optIfOTSnSrcCurrentHighOutputPower Integer32
  optIfOTSnSrcCurrentLowerOutputPowerThreshold Integer32
  optIfOTSnSrcCurrentUpperOutputPowerThreshold Integer32
  optIfOTSnSrcCurrentInputPower Integer32
  optIfOTSnSrcCurrentLowInputPower Integer32
  optIfOTSnSrcCurrentHighInputPower Integer32
  optIfOTSnSrcCurrentLowerInputPowerThreshold Integer32
  optIfOTSnSrcCurrentUpperInputPowerThreshold Integer32

OptIfOTSnSrcIntervalEntry  
SEQUENCE    
  optIfOTSnSrcIntervalNumber OptIfIntervalNumber
  optIfOTSnSrcIntervalSuspectedFlag TruthValue
  optIfOTSnSrcIntervalLastOutputPower Integer32
  optIfOTSnSrcIntervalLowOutputPower Integer32
  optIfOTSnSrcIntervalHighOutputPower Integer32
  optIfOTSnSrcIntervalLastInputPower Integer32
  optIfOTSnSrcIntervalLowInputPower Integer32
  optIfOTSnSrcIntervalHighInputPower Integer32

OptIfOTSnSrcCurDayEntry  
SEQUENCE    
  optIfOTSnSrcCurDaySuspectedFlag TruthValue
  optIfOTSnSrcCurDayLowOutputPower Integer32
  optIfOTSnSrcCurDayHighOutputPower Integer32
  optIfOTSnSrcCurDayLowInputPower Integer32
  optIfOTSnSrcCurDayHighInputPower Integer32

OptIfOTSnSrcPrevDayEntry  
SEQUENCE    
  optIfOTSnSrcPrevDaySuspectedFlag TruthValue
  optIfOTSnSrcPrevDayLastOutputPower Integer32
  optIfOTSnSrcPrevDayLowOutputPower Integer32
  optIfOTSnSrcPrevDayHighOutputPower Integer32
  optIfOTSnSrcPrevDayLastInputPower Integer32
  optIfOTSnSrcPrevDayLowInputPower Integer32
  optIfOTSnSrcPrevDayHighInputPower Integer32

OptIfOMSnConfigEntry  
SEQUENCE    
  optIfOMSnDirectionality OptIfDirectionality
  optIfOMSnCurrentStatus BITS

OptIfOMSnSinkCurrentEntry  
SEQUENCE    
  optIfOMSnSinkCurrentSuspectedFlag TruthValue
  optIfOMSnSinkCurrentAggregatedInputPower Integer32
  optIfOMSnSinkCurrentLowAggregatedInputPower Integer32
  optIfOMSnSinkCurrentHighAggregatedInputPower Integer32
  optIfOMSnSinkCurrentLowerInputPowerThreshold Integer32
  optIfOMSnSinkCurrentUpperInputPowerThreshold Integer32
  optIfOMSnSinkCurrentOutputPower Integer32
  optIfOMSnSinkCurrentLowOutputPower Integer32
  optIfOMSnSinkCurrentHighOutputPower Integer32
  optIfOMSnSinkCurrentLowerOutputPowerThreshold Integer32
  optIfOMSnSinkCurrentUpperOutputPowerThreshold Integer32

OptIfOMSnSinkIntervalEntry  
SEQUENCE    
  optIfOMSnSinkIntervalNumber OptIfIntervalNumber
  optIfOMSnSinkIntervalSuspectedFlag TruthValue
  optIfOMSnSinkIntervalLastAggregatedInputPower Integer32
  optIfOMSnSinkIntervalLowAggregatedInputPower Integer32
  optIfOMSnSinkIntervalHighAggregatedInputPower Integer32
  optIfOMSnSinkIntervalLastOutputPower Integer32
  optIfOMSnSinkIntervalLowOutputPower Integer32
  optIfOMSnSinkIntervalHighOutputPower Integer32

OptIfOMSnSinkCurDayEntry  
SEQUENCE    
  optIfOMSnSinkCurDaySuspectedFlag TruthValue
  optIfOMSnSinkCurDayLowAggregatedInputPower Integer32
  optIfOMSnSinkCurDayHighAggregatedInputPower Integer32
  optIfOMSnSinkCurDayLowOutputPower Integer32
  optIfOMSnSinkCurDayHighOutputPower Integer32

OptIfOMSnSinkPrevDayEntry  
SEQUENCE    
  optIfOMSnSinkPrevDaySuspectedFlag TruthValue
  optIfOMSnSinkPrevDayLastAggregatedInputPower Integer32
  optIfOMSnSinkPrevDayLowAggregatedInputPower Integer32
  optIfOMSnSinkPrevDayHighAggregatedInputPower Integer32
  optIfOMSnSinkPrevDayLastOutputPower Integer32
  optIfOMSnSinkPrevDayLowOutputPower Integer32
  optIfOMSnSinkPrevDayHighOutputPower Integer32

OptIfOMSnSrcCurrentEntry  
SEQUENCE    
  optIfOMSnSrcCurrentSuspectedFlag TruthValue
  optIfOMSnSrcCurrentOutputPower Integer32
  optIfOMSnSrcCurrentLowOutputPower Integer32
  optIfOMSnSrcCurrentHighOutputPower Integer32
  optIfOMSnSrcCurrentLowerOutputPowerThreshold Integer32
  optIfOMSnSrcCurrentUpperOutputPowerThreshold Integer32
  optIfOMSnSrcCurrentAggregatedInputPower Integer32
  optIfOMSnSrcCurrentLowAggregatedInputPower Integer32
  optIfOMSnSrcCurrentHighAggregatedInputPower Integer32
  optIfOMSnSrcCurrentLowerInputPowerThreshold Integer32
  optIfOMSnSrcCurrentUpperInputPowerThreshold Integer32

OptIfOMSnSrcIntervalEntry  
SEQUENCE    
  optIfOMSnSrcIntervalNumber OptIfIntervalNumber
  optIfOMSnSrcIntervalSuspectedFlag TruthValue
  optIfOMSnSrcIntervalLastOutputPower Integer32
  optIfOMSnSrcIntervalLowOutputPower Integer32
  optIfOMSnSrcIntervalHighOutputPower Integer32
  optIfOMSnSrcIntervalLastAggregatedInputPower Integer32
  optIfOMSnSrcIntervalLowAggregatedInputPower Integer32
  optIfOMSnSrcIntervalHighAggregatedInputPower Integer32

OptIfOMSnSrcCurDayEntry  
SEQUENCE    
  optIfOMSnSrcCurDaySuspectedFlag TruthValue
  optIfOMSnSrcCurDayLowOutputPower Integer32
  optIfOMSnSrcCurDayHighOutputPower Integer32
  optIfOMSnSrcCurDayLowAggregatedInputPower Integer32
  optIfOMSnSrcCurDayHighAggregatedInputPower Integer32

OptIfOMSnSrcPrevDayEntry  
SEQUENCE    
  optIfOMSnSrcPrevDaySuspectedFlag TruthValue
  optIfOMSnSrcPrevDayLastOutputPower Integer32
  optIfOMSnSrcPrevDayLowOutputPower Integer32
  optIfOMSnSrcPrevDayHighOutputPower Integer32
  optIfOMSnSrcPrevDayLastAggregatedInputPower Integer32
  optIfOMSnSrcPrevDayLowAggregatedInputPower Integer32
  optIfOMSnSrcPrevDayHighAggregatedInputPower Integer32

OptIfOChGroupConfigEntry  
SEQUENCE    
  optIfOChGroupDirectionality OptIfDirectionality

OptIfOChGroupSinkCurrentEntry  
SEQUENCE    
  optIfOChGroupSinkCurrentSuspectedFlag TruthValue
  optIfOChGroupSinkCurrentAggregatedInputPower Integer32
  optIfOChGroupSinkCurrentLowAggregatedInputPower Integer32
  optIfOChGroupSinkCurrentHighAggregatedInputPower Integer32
  optIfOChGroupSinkCurrentLowerInputPowerThreshold Integer32
  optIfOChGroupSinkCurrentUpperInputPowerThreshold Integer32
  optIfOChGroupSinkCurrentOutputPower Integer32
  optIfOChGroupSinkCurrentLowOutputPower Integer32
  optIfOChGroupSinkCurrentHighOutputPower Integer32
  optIfOChGroupSinkCurrentLowerOutputPowerThreshold Integer32
  optIfOChGroupSinkCurrentUpperOutputPowerThreshold Integer32

OptIfOChGroupSinkIntervalEntry  
SEQUENCE    
  optIfOChGroupSinkIntervalNumber OptIfIntervalNumber
  optIfOChGroupSinkIntervalSuspectedFlag TruthValue
  optIfOChGroupSinkIntervalLastAggregatedInputPower Integer32
  optIfOChGroupSinkIntervalLowAggregatedInputPower Integer32
  optIfOChGroupSinkIntervalHighAggregatedInputPower Integer32
  optIfOChGroupSinkIntervalLastOutputPower Integer32
  optIfOChGroupSinkIntervalLowOutputPower Integer32
  optIfOChGroupSinkIntervalHighOutputPower Integer32

OptIfOChGroupSinkCurDayEntry  
SEQUENCE    
  optIfOChGroupSinkCurDaySuspectedFlag TruthValue
  optIfOChGroupSinkCurDayLowAggregatedInputPower Integer32
  optIfOChGroupSinkCurDayHighAggregatedInputPower Integer32
  optIfOChGroupSinkCurDayLowOutputPower Integer32
  optIfOChGroupSinkCurDayHighOutputPower Integer32

OptIfOChGroupSinkPrevDayEntry  
SEQUENCE    
  optIfOChGroupSinkPrevDaySuspectedFlag TruthValue
  optIfOChGroupSinkPrevDayLastAggregatedInputPower Integer32
  optIfOChGroupSinkPrevDayLowAggregatedInputPower Integer32
  optIfOChGroupSinkPrevDayHighAggregatedInputPower Integer32
  optIfOChGroupSinkPrevDayLastOutputPower Integer32
  optIfOChGroupSinkPrevDayLowOutputPower Integer32
  optIfOChGroupSinkPrevDayHighOutputPower Integer32

OptIfOChGroupSrcCurrentEntry  
SEQUENCE    
  optIfOChGroupSrcCurrentSuspectedFlag TruthValue
  optIfOChGroupSrcCurrentOutputPower Integer32
  optIfOChGroupSrcCurrentLowOutputPower Integer32
  optIfOChGroupSrcCurrentHighOutputPower Integer32
  optIfOChGroupSrcCurrentLowerOutputPowerThreshold Integer32
  optIfOChGroupSrcCurrentUpperOutputPowerThreshold Integer32
  optIfOChGroupSrcCurrentAggregatedInputPower Integer32
  optIfOChGroupSrcCurrentLowAggregatedInputPower Integer32
  optIfOChGroupSrcCurrentHighAggregatedInputPower Integer32
  optIfOChGroupSrcCurrentLowerInputPowerThreshold Integer32
  optIfOChGroupSrcCurrentUpperInputPowerThreshold Integer32

OptIfOChGroupSrcIntervalEntry  
SEQUENCE    
  optIfOChGroupSrcIntervalNumber OptIfIntervalNumber
  optIfOChGroupSrcIntervalSuspectedFlag TruthValue
  optIfOChGroupSrcIntervalLastOutputPower Integer32
  optIfOChGroupSrcIntervalLowOutputPower Integer32
  optIfOChGroupSrcIntervalHighOutputPower Integer32
  optIfOChGroupSrcIntervalLastAggregatedInputPower Integer32
  optIfOChGroupSrcIntervalLowAggregatedInputPower Integer32
  optIfOChGroupSrcIntervalHighAggregatedInputPower Integer32

OptIfOChGroupSrcCurDayEntry  
SEQUENCE    
  optIfOChGroupSrcCurDaySuspectedFlag TruthValue
  optIfOChGroupSrcCurDayLowOutputPower Integer32
  optIfOChGroupSrcCurDayHighOutputPower Integer32
  optIfOChGroupSrcCurDayLowAggregatedInputPower Integer32
  optIfOChGroupSrcCurDayHighAggregatedInputPower Integer32

OptIfOChGroupSrcPrevDayEntry  
SEQUENCE    
  optIfOChGroupSrcPrevDaySuspectedFlag TruthValue
  optIfOChGroupSrcPrevDayLastOutputPower Integer32
  optIfOChGroupSrcPrevDayLowOutputPower Integer32
  optIfOChGroupSrcPrevDayHighOutputPower Integer32
  optIfOChGroupSrcPrevDayLastAggregatedInputPower Integer32
  optIfOChGroupSrcPrevDayLowAggregatedInputPower Integer32
  optIfOChGroupSrcPrevDayHighAggregatedInputPower Integer32

OptIfOChConfigEntry  
SEQUENCE    
  optIfOChDirectionality OptIfDirectionality
  optIfOChCurrentStatus BITS

OptIfOChSinkCurrentEntry  
SEQUENCE    
  optIfOChSinkCurrentSuspectedFlag TruthValue
  optIfOChSinkCurrentInputPower Integer32
  optIfOChSinkCurrentLowInputPower Integer32
  optIfOChSinkCurrentHighInputPower Integer32
  optIfOChSinkCurrentLowerInputPowerThreshold Integer32
  optIfOChSinkCurrentUpperInputPowerThreshold Integer32

OptIfOChSinkIntervalEntry  
SEQUENCE    
  optIfOChSinkIntervalNumber OptIfIntervalNumber
  optIfOChSinkIntervalSuspectedFlag TruthValue
  optIfOChSinkIntervalLastInputPower Integer32
  optIfOChSinkIntervalLowInputPower Integer32
  optIfOChSinkIntervalHighInputPower Integer32

OptIfOChSinkCurDayEntry  
SEQUENCE    
  optIfOChSinkCurDaySuspectedFlag TruthValue
  optIfOChSinkCurDayLowInputPower Integer32
  optIfOChSinkCurDayHighInputPower Integer32

OptIfOChSinkPrevDayEntry  
SEQUENCE    
  optIfOChSinkPrevDaySuspectedFlag TruthValue
  optIfOChSinkPrevDayLastInputPower Integer32
  optIfOChSinkPrevDayLowInputPower Integer32
  optIfOChSinkPrevDayHighInputPower Integer32

OptIfOChSrcCurrentEntry  
SEQUENCE    
  optIfOChSrcCurrentSuspectedFlag TruthValue
  optIfOChSrcCurrentOutputPower Integer32
  optIfOChSrcCurrentLowOutputPower Integer32
  optIfOChSrcCurrentHighOutputPower Integer32
  optIfOChSrcCurrentLowerOutputPowerThreshold Integer32
  optIfOChSrcCurrentUpperOutputPowerThreshold Integer32

OptIfOChSrcIntervalEntry  
SEQUENCE    
  optIfOChSrcIntervalNumber OptIfIntervalNumber
  optIfOChSrcIntervalSuspectedFlag TruthValue
  optIfOChSrcIntervalLastOutputPower Integer32
  optIfOChSrcIntervalLowOutputPower Integer32
  optIfOChSrcIntervalHighOutputPower Integer32

OptIfOChSrcCurDayEntry  
SEQUENCE    
  optIfOChSrcCurDaySuspectedFlag TruthValue
  optIfOChSrcCurDayLowOutputPower Integer32
  optIfOChSrcCurDayHighOutputPower Integer32

OptIfOChSrcPrevDayEntry  
SEQUENCE    
  optIfOChSrcPrevDaySuspectedFlag TruthValue
  optIfOChSrcPrevDayLastOutputPower Integer32
  optIfOChSrcPrevDayLowOutputPower Integer32
  optIfOChSrcPrevDayHighOutputPower Integer32

OptIfOTUkConfigEntry  
SEQUENCE    
  optIfOTUkDirectionality OptIfDirectionality
  optIfOTUkBitRateK OptIfBitRateK
  optIfOTUkTraceIdentifierTransmitted OptIfTxTI
  optIfOTUkDAPIExpected OptIfExDAPI
  optIfOTUkSAPIExpected OptIfExSAPI
  optIfOTUkTraceIdentifierAccepted OptIfAcTI
  optIfOTUkTIMDetMode OptIfTIMDetMode
  optIfOTUkTIMActEnabled TruthValue
  optIfOTUkDEGThr OptIfDEGThr
  optIfOTUkDEGM OptIfDEGM
  optIfOTUkSinkAdaptActive TruthValue
  optIfOTUkSourceAdaptActive TruthValue
  optIfOTUkSinkFECEnabled TruthValue
  optIfOTUkCurrentStatus BITS

OptIfGCC0ConfigEntry  
SEQUENCE    
  optIfGCC0Directionality OptIfDirectionality
  optIfGCC0Application SnmpAdminString
  optIfGCC0RowStatus RowStatus

OptIfODUkConfigEntry  
SEQUENCE    
  optIfODUkDirectionality OptIfDirectionality
  optIfODUkBitRateK OptIfBitRateK
  optIfODUkTcmFieldsInUse BITS
  optIfODUkPositionSeqCurrentSize Unsigned32
  optIfODUkTtpPresent TruthValue

OptIfODUkTtpConfigEntry  
SEQUENCE    
  optIfODUkTtpTraceIdentifierTransmitted OptIfTxTI
  optIfODUkTtpDAPIExpected OptIfExDAPI
  optIfODUkTtpSAPIExpected OptIfExSAPI
  optIfODUkTtpTraceIdentifierAccepted OptIfAcTI
  optIfODUkTtpTIMDetMode OptIfTIMDetMode
  optIfODUkTtpTIMActEnabled TruthValue
  optIfODUkTtpDEGThr OptIfDEGThr
  optIfODUkTtpDEGM OptIfDEGM
  optIfODUkTtpCurrentStatus BITS

OptIfODUkPositionSeqEntry  
SEQUENCE    
  optIfODUkPositionSeqIndex Unsigned32
  optIfODUkPositionSeqPosition Unsigned32
  optIfODUkPositionSeqPointer RowPointer

OptIfODUkNimConfigEntry  
SEQUENCE    
  optIfODUkNimDirectionality OptIfSinkOrSource
  optIfODUkNimDAPIExpected OptIfExDAPI
  optIfODUkNimSAPIExpected OptIfExSAPI
  optIfODUkNimTraceIdentifierAccepted OptIfAcTI
  optIfODUkNimTIMDetMode OptIfTIMDetMode
  optIfODUkNimTIMActEnabled TruthValue
  optIfODUkNimDEGThr OptIfDEGThr
  optIfODUkNimDEGM OptIfDEGM
  optIfODUkNimCurrentStatus BITS
  optIfODUkNimRowStatus RowStatus

OptIfGCC12ConfigEntry  
SEQUENCE    
  optIfGCC12Codirectional TruthValue
  optIfGCC12GCCAccess INTEGER
  optIfGCC12GCCPassThrough TruthValue
  optIfGCC12Application SnmpAdminString
  optIfGCC12RowStatus RowStatus

OptIfODUkTConfigEntry  
SEQUENCE    
  optIfODUkTTcmField Unsigned32
  optIfODUkTCodirectional TruthValue
  optIfODUkTTraceIdentifierTransmitted OptIfTxTI
  optIfODUkTDAPIExpected OptIfExDAPI
  optIfODUkTSAPIExpected OptIfExSAPI
  optIfODUkTTraceIdentifierAccepted OptIfAcTI
  optIfODUkTTIMDetMode OptIfTIMDetMode
  optIfODUkTTIMActEnabled TruthValue
  optIfODUkTDEGThr OptIfDEGThr
  optIfODUkTDEGM OptIfDEGM
  optIfODUkTSinkMode INTEGER
  optIfODUkTSinkLockSignalAdminState INTEGER
  optIfODUkTSourceLockSignalAdminState INTEGER
  optIfODUkTCurrentStatus BITS
  optIfODUkTRowStatus RowStatus

OptIfODUkTNimConfigEntry  
SEQUENCE    
  optIfODUkTNimTcmField Unsigned32
  optIfODUkTNimDirectionality OptIfSinkOrSource
  optIfODUkTNimDAPIExpected OptIfExDAPI
  optIfODUkTNimSAPIExpected OptIfExSAPI
  optIfODUkTNimTraceIdentifierAccepted OptIfAcTI
  optIfODUkTNimTIMDetMode OptIfTIMDetMode
  optIfODUkTNimTIMActEnabled TruthValue
  optIfODUkTNimDEGThr OptIfDEGThr
  optIfODUkTNimDEGM OptIfDEGM
  optIfODUkTNimCurrentStatus BITS
  optIfODUkTNimRowStatus RowStatus

Defined Values

optIfMibModule 1.3.6.1.2.1.10.133
The MIB module to describe pre-OTN and OTN interfaces. Copyright (C) The Internet Society (2003). This version of this MIB module is part of RFC 3591; see the RFC itself for full legal notices.
MODULE-IDENTITY    

optIfObjects 1.3.6.1.2.1.10.133.1
OBJECT IDENTIFIER    

optIfConfs 1.3.6.1.2.1.10.133.2
OBJECT IDENTIFIER    

optIfOTMn 1.3.6.1.2.1.10.133.1.1
OBJECT IDENTIFIER    

optIfPerfMon 1.3.6.1.2.1.10.133.1.2
OBJECT IDENTIFIER    

optIfOTSn 1.3.6.1.2.1.10.133.1.3
OBJECT IDENTIFIER    

optIfOMSn 1.3.6.1.2.1.10.133.1.4
OBJECT IDENTIFIER    

optIfOChGroup 1.3.6.1.2.1.10.133.1.5
OBJECT IDENTIFIER    

optIfOCh 1.3.6.1.2.1.10.133.1.6
OBJECT IDENTIFIER    

optIfOTUk 1.3.6.1.2.1.10.133.1.7
OBJECT IDENTIFIER    

optIfODUk 1.3.6.1.2.1.10.133.1.8
OBJECT IDENTIFIER    

optIfODUkT 1.3.6.1.2.1.10.133.1.9
OBJECT IDENTIFIER    

optIfGroups 1.3.6.1.2.1.10.133.2.1
OBJECT IDENTIFIER    

optIfCompl 1.3.6.1.2.1.10.133.2.2
OBJECT IDENTIFIER    

optIfOTMnTable 1.3.6.1.2.1.10.133.1.1.1
A table of OTMn structure information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOTMnEntry

optIfOTMnEntry 1.3.6.1.2.1.10.133.1.1.1.1
A conceptual row that contains the OTMn structure information of an optical interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOTMnEntry  

optIfOTMnOrder 1.3.6.1.2.1.10.133.1.1.1.1.1
This object indicates the order of the OTM, which represents the maximum number of wavelengths that can be supported at the bit rate(s) supported on the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..900  

optIfOTMnReduced 1.3.6.1.2.1.10.133.1.1.1.1.2
This object indicates whether a reduced or full functionality is supported at the interface. A value of true means reduced. A value of false means full.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOTMnBitRates 1.3.6.1.2.1.10.133.1.1.1.1.3
This attribute is a bit map representing the bit rate or set of bit rates supported on the interface. The meaning of each bit position is as follows: bitRateK1(0) is set if the 2.5 Gbit/s rate is supported bitRateK2(1) is set if the 10 Gbit/s rate is supported bitRateK3(2) is set if the 40 Gbit/s rate is supported Note that each bit position corresponds to one possible value of the type OptIfBitRateK. The default value of this attribute is system specific.
Status: current Access: read-only
OBJECT-TYPE    
  BITS bitRateK1(0), bitRateK2(1), bitRateK3(2)  

optIfOTMnInterfaceType 1.3.6.1.2.1.10.133.1.1.1.1.4
This object identifies the type of interface. The value of this attribute will affect the behavior of the OTM with respect to presence/absence of OTM Overhead Signal (OOS) processing and TCM activation. For an IrDI interface, there is no OOS processing and TCM activation is limited to n levels as specified by a TCM level threshold. This object contains two fields that are separated by whitespace. The possible values are: field 1: one of the 4-character ASCII strings 'IrDI' or 'IaDI' field 2: free-form text consisting of printable UTF-8 encoded characters Note that field 2 is optional. If it is not present then there is no requirement for trailing whitespace after field 1. The default values are as follows: field 1: 'IaDI' field 2: an empty string.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

optIfOTMnTcmMax 1.3.6.1.2.1.10.133.1.1.1.1.5
This object identifies the maximum number of TCM levels allowed for any Optical Channel contained in this OTM. A new TCM activation will be rejected if the requested level is greater than the threshold. If InterfaceType object specifies a type of 'IaDI' for this OTM, then this attribute is irrelevant. Possible values: unsigned integers in the range from 0 to 6 inclusive. Default value: 3.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..6  

optIfOTMnOpticalReach 1.3.6.1.2.1.10.133.1.1.1.1.6
This object indicates the length the optical signal may travel before requiring termination or regeneration. The meaning of the enumeration are: intraOffice(1) - intra-office (as defined in ITU-T G.957) shortHaul(2) - short haul (as defined in ITU-T G.957) longHaul(3) - long haul (as defined in ITU-T G.957) veryLongHaul(4) - very long haul (as defined in ITU-T G.691) ultraLongHaul(5)- ultra long haul (as defined in ITU-T G.691)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER intraOffice(1), shortHaul(2), longHaul(3), veryLongHaul(4), ultraLongHaul(5)  

optIfPerfMonIntervalTable 1.3.6.1.2.1.10.133.1.2.1
A table of 15-minute performance monitoring interval information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfPerfMonIntervalEntry

optIfPerfMonIntervalEntry 1.3.6.1.2.1.10.133.1.2.1.1
A conceptual row that contains 15-minute performance monitoring interval information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfPerfMonIntervalEntry  

optIfPerfMonCurrentTimeElapsed 1.3.6.1.2.1.10.133.1.2.1.1.1
Number of seconds elapsed in the current 15-minute performance monitoring interval. If, for some reason, such as an adjustment in the NE's time-of-day clock, the number of seconds elapsed exceeds the maximum value, then the maximum value will be returned.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..900  

optIfPerfMonCurDayTimeElapsed 1.3.6.1.2.1.10.133.1.2.1.1.2
Number of seconds elapsed in the current 24-hour interval performance monitoring period. If, for some reason, such as an adjustment in the NE's time-of-day clock, the number of seconds elapsed exceeds the maximum value, then the maximum value will be returned.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..86400  

optIfPerfMonIntervalNumIntervals 1.3.6.1.2.1.10.133.1.2.1.1.3
The number of 15-minute intervals for which performance monitoring data is available. The number is the same for all the associated sub layers of the interface. An optical interface must be capable of supporting at least n intervals, where n is defined as follows: The minimum value of n is 4. The default of n is 32. The maximum value of n is 96. The value of this object will be n unless performance monitoring was (re-)started for the interface within the last (n*15) minutes, in which case the value will be the number of complete 15-minute intervals since measurement was (re-)started.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..96  

optIfPerfMonIntervalNumInvalidIntervals 1.3.6.1.2.1.10.133.1.2.1.1.4
The number of intervals in the range from 0 to optIfPerfMonIntervalNumIntervals for which no performance monitoring data is available and/or the data is invalid.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..96  

optIfOTSnConfigTable 1.3.6.1.2.1.10.133.1.3.1
A table of OTSn configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOTSnConfigEntry

optIfOTSnConfigEntry 1.3.6.1.2.1.10.133.1.3.1.1
A conceptual row that contains OTSn configuration information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOTSnConfigEntry  

optIfOTSnDirectionality 1.3.6.1.2.1.10.133.1.3.1.1.1
Indicates the directionality of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  OptIfDirectionality  

optIfOTSnAprStatus 1.3.6.1.2.1.10.133.1.3.1.1.2
This attribute indicates the status of the Automatic Power Reduction (APR) function of the entity. Valid values are 'on' and 'off'.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

optIfOTSnAprControl 1.3.6.1.2.1.10.133.1.3.1.1.3
This object is a UTF-8 encoded string that specifies Automatic Power Reduction (APR) control actions requested of this entity (when written) and that returns the current APR control state of this entity (when read). The values are implementation-defined. Any implementation that instantiates this object must document the set of values that it allows to be written, the set of values that it will return, and what each of those values means.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

optIfOTSnTraceIdentifierTransmitted 1.3.6.1.2.1.10.133.1.3.1.1.4
The trace identifier transmitted. This object is applicable when optIfOTSnDirectionality has the value source(2) or bidirectional(3). This object does not apply to reduced-capability systems (i.e., those for which optIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 has the value 'IrDI'). If no value is ever set by a management entity for the object optIfOTSnTraceIdentifierTransmitted, system-specific default value will be used. Any implementation that instantiates this object must document the system-specific default value or how it is derived.
Status: current Access: read-write
OBJECT-TYPE    
  OptIfTxTI  

optIfOTSnDAPIExpected 1.3.6.1.2.1.10.133.1.3.1.1.5
The DAPI expected by the receiver. This object is applicable when optIfOTSnDirectionality has the value sink(1) or bidirectional(3). It has no effect if optIfOTSnTIMDetMode has the value off(1) or sapi(3). This object does not apply to reduced-capability systems (i.e., those for which optIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 has the value 'IrDI').
Status: current Access: read-write
OBJECT-TYPE    
  OptIfExDAPI  

optIfOTSnSAPIExpected 1.3.6.1.2.1.10.133.1.3.1.1.6
The SAPI expected by the receiver. This object is applicable when optIfOTSnDirectionality has the value sink(1) or bidirectional(3). It has no effect if optIfOTSnTIMDetMode has the value off(1) or dapi(2). This object does not apply to reduced-capability systems (i.e., those for which optIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 has the value 'IrDI').
Status: current Access: read-write
OBJECT-TYPE    
  OptIfExSAPI  

optIfOTSnTraceIdentifierAccepted 1.3.6.1.2.1.10.133.1.3.1.1.7
The actual trace identifier received. This object is applicable when optIfOTSnDirectionality has the value sink(1) or bidirectional(3). Its value is unspecified if optIfOTSnCurrentStatus has either or both of the losO(5) and los(6) bits set. This object does not apply to reduced-capability systems (i.e., those for which optIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 has the value 'IrDI').
Status: current Access: read-only
OBJECT-TYPE    
  OptIfAcTI  

optIfOTSnTIMDetMode 1.3.6.1.2.1.10.133.1.3.1.1.8
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is applicable when optIfOTSnDirectionality has the value sink(1) or bidirectional(3). The default value is off(1). This object does not apply to reduced-capability systems (i.e., those for which optIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 has the value 'IrDI'). The default value of this object is off(1).
Status: current Access: read-write
OBJECT-TYPE    
  OptIfTIMDetMode  

optIfOTSnTIMActEnabled 1.3.6.1.2.1.10.133.1.3.1.1.9
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is applicable when optIfOTSnDirectionality has the value sink(1) or bidirectional(3). It has no effect when the value of optIfOTSnTIMDetMode is off(1). This object does not apply to reduced-capability systems (i.e., those for which optIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 has the value 'IrDI'). The default value of this object is false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

optIfOTSnCurrentStatus 1.3.6.1.2.1.10.133.1.3.1.1.10
Indicates the defect condition of the entity, if any. This object is applicable when optIfOTSnDirectionality has the value sink(1) or bidirectional(3). In reduced-capability systems or at IrDI interfaces the only bit position that may be set is los(6).
Status: current Access: read-only
OBJECT-TYPE    
  BITS bdiP(0), bdiO(1), bdi(2), tim(3), losP(4), losO(5), los(6)  

optIfOTSnSinkCurrentTable 1.3.6.1.2.1.10.133.1.3.2
A table of OTSn sink performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOTSnSinkCurrentEntry

optIfOTSnSinkCurrentEntry 1.3.6.1.2.1.10.133.1.3.2.1
A conceptual row that contains OTSn sink performance monitoring information of an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOTSnSinkCurrentEntry  

optIfOTSnSinkCurrentSuspectedFlag 1.3.6.1.2.1.10.133.1.3.2.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOTSnSinkCurrentInputPower 1.3.6.1.2.1.10.133.1.3.2.1.2
The optical power monitored at the input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkCurrentLowInputPower 1.3.6.1.2.1.10.133.1.3.2.1.3
The lowest optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkCurrentHighInputPower 1.3.6.1.2.1.10.133.1.3.2.1.4
The highest optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkCurrentLowerInputPowerThreshold 1.3.6.1.2.1.10.133.1.3.2.1.5
The lower limit threshold on input power. If optIfOTSnSinkCurrentInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkCurrentUpperInputPowerThreshold 1.3.6.1.2.1.10.133.1.3.2.1.6
The upper limit threshold on input power. If optIfOTSnSinkCurrentInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkCurrentOutputPower 1.3.6.1.2.1.10.133.1.3.2.1.7
The optical power monitored at the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkCurrentLowOutputPower 1.3.6.1.2.1.10.133.1.3.2.1.8
The lowest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkCurrentHighOutputPower 1.3.6.1.2.1.10.133.1.3.2.1.9
The highest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkCurrentLowerOutputPowerThreshold 1.3.6.1.2.1.10.133.1.3.2.1.10
The lower limit threshold on output power. If optIfOTSnSinkCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkCurrentUpperOutputPowerThreshold 1.3.6.1.2.1.10.133.1.3.2.1.11
The upper limit threshold on output power. If optIfOTSnSinkCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkIntervalTable 1.3.6.1.2.1.10.133.1.3.3
A table of historical OTSn sink performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOTSnSinkIntervalEntry

optIfOTSnSinkIntervalEntry 1.3.6.1.2.1.10.133.1.3.3.1
A conceptual row that contains OTSn sink performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOTSnSinkIntervalEntry  

optIfOTSnSinkIntervalNumber 1.3.6.1.2.1.10.133.1.3.3.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfIntervalNumber  

optIfOTSnSinkIntervalSuspectedFlag 1.3.6.1.2.1.10.133.1.3.3.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOTSnSinkIntervalLastInputPower 1.3.6.1.2.1.10.133.1.3.3.1.3
The last optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkIntervalLowInputPower 1.3.6.1.2.1.10.133.1.3.3.1.4
The lowest optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkIntervalHighInputPower 1.3.6.1.2.1.10.133.1.3.3.1.5
The highest optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkIntervalLastOutputPower 1.3.6.1.2.1.10.133.1.3.3.1.6
The last optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkIntervalLowOutputPower 1.3.6.1.2.1.10.133.1.3.3.1.7
The lowest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkIntervalHighOutputPower 1.3.6.1.2.1.10.133.1.3.3.1.8
The highest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkCurDayTable 1.3.6.1.2.1.10.133.1.3.4
A table of OTSn sink performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOTSnSinkCurDayEntry

optIfOTSnSinkCurDayEntry 1.3.6.1.2.1.10.133.1.3.4.1
A conceptual row that contains OTSn sink performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOTSnSinkCurDayEntry  

optIfOTSnSinkCurDaySuspectedFlag 1.3.6.1.2.1.10.133.1.3.4.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOTSnSinkCurDayLowInputPower 1.3.6.1.2.1.10.133.1.3.4.1.2
The lowest optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkCurDayHighInputPower 1.3.6.1.2.1.10.133.1.3.4.1.3
The highest optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkCurDayLowOutputPower 1.3.6.1.2.1.10.133.1.3.4.1.4
The lowest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkCurDayHighOutputPower 1.3.6.1.2.1.10.133.1.3.4.1.5
The highest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkPrevDayTable 1.3.6.1.2.1.10.133.1.3.5
A table of OTSn sink performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOTSnSinkPrevDayEntry

optIfOTSnSinkPrevDayEntry 1.3.6.1.2.1.10.133.1.3.5.1
A conceptual row that contains OTSn sink performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOTSnSinkPrevDayEntry  

optIfOTSnSinkPrevDaySuspectedFlag 1.3.6.1.2.1.10.133.1.3.5.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOTSnSinkPrevDayLastInputPower 1.3.6.1.2.1.10.133.1.3.5.1.2
The last optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkPrevDayLowInputPower 1.3.6.1.2.1.10.133.1.3.5.1.3
The lowest optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkPrevDayHighInputPower 1.3.6.1.2.1.10.133.1.3.5.1.4
The highest optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkPrevDayLastOutputPower 1.3.6.1.2.1.10.133.1.3.5.1.5
The last optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkPrevDayLowOutputPower 1.3.6.1.2.1.10.133.1.3.5.1.6
The lowest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSinkPrevDayHighOutputPower 1.3.6.1.2.1.10.133.1.3.5.1.7
The highest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcCurrentTable 1.3.6.1.2.1.10.133.1.3.6
A table of OTSn source performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOTSnSrcCurrentEntry

optIfOTSnSrcCurrentEntry 1.3.6.1.2.1.10.133.1.3.6.1
A conceptual row that contains OTSn source performance monitoring information of an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOTSnSrcCurrentEntry  

optIfOTSnSrcCurrentSuspectedFlag 1.3.6.1.2.1.10.133.1.3.6.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOTSnSrcCurrentOutputPower 1.3.6.1.2.1.10.133.1.3.6.1.2
The optical power monitored at the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcCurrentLowOutputPower 1.3.6.1.2.1.10.133.1.3.6.1.3
The lowest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcCurrentHighOutputPower 1.3.6.1.2.1.10.133.1.3.6.1.4
The highest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcCurrentLowerOutputPowerThreshold 1.3.6.1.2.1.10.133.1.3.6.1.5
The lower limit threshold on output power. If optIfOTSnSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcCurrentUpperOutputPowerThreshold 1.3.6.1.2.1.10.133.1.3.6.1.6
The upper limit threshold on output power. If optIfOTSnSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcCurrentInputPower 1.3.6.1.2.1.10.133.1.3.6.1.7
The optical power monitored at the input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcCurrentLowInputPower 1.3.6.1.2.1.10.133.1.3.6.1.8
The lowest optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcCurrentHighInputPower 1.3.6.1.2.1.10.133.1.3.6.1.9
The highest optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcCurrentLowerInputPowerThreshold 1.3.6.1.2.1.10.133.1.3.6.1.10
The lower limit threshold on input power. If optIfOTSnSrcCurrentInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcCurrentUpperInputPowerThreshold 1.3.6.1.2.1.10.133.1.3.6.1.11
The upper limit threshold on input power. If optIfOTSnSrcCurrentInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcIntervalTable 1.3.6.1.2.1.10.133.1.3.7
A table of historical OTSn source performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOTSnSrcIntervalEntry

optIfOTSnSrcIntervalEntry 1.3.6.1.2.1.10.133.1.3.7.1
A conceptual row that contains OTSn source performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOTSnSrcIntervalEntry  

optIfOTSnSrcIntervalNumber 1.3.6.1.2.1.10.133.1.3.7.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfIntervalNumber  

optIfOTSnSrcIntervalSuspectedFlag 1.3.6.1.2.1.10.133.1.3.7.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOTSnSrcIntervalLastOutputPower 1.3.6.1.2.1.10.133.1.3.7.1.3
The last optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcIntervalLowOutputPower 1.3.6.1.2.1.10.133.1.3.7.1.4
The lowest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcIntervalHighOutputPower 1.3.6.1.2.1.10.133.1.3.7.1.5
The highest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcIntervalLastInputPower 1.3.6.1.2.1.10.133.1.3.7.1.6
The last optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcIntervalLowInputPower 1.3.6.1.2.1.10.133.1.3.7.1.7
The lowest optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcIntervalHighInputPower 1.3.6.1.2.1.10.133.1.3.7.1.8
The highest optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcCurDayTable 1.3.6.1.2.1.10.133.1.3.8
A table of OTSn source performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOTSnSrcCurDayEntry

optIfOTSnSrcCurDayEntry 1.3.6.1.2.1.10.133.1.3.8.1
A conceptual row that contains OTSn source performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOTSnSrcCurDayEntry  

optIfOTSnSrcCurDaySuspectedFlag 1.3.6.1.2.1.10.133.1.3.8.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOTSnSrcCurDayLowOutputPower 1.3.6.1.2.1.10.133.1.3.8.1.2
The lowest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcCurDayHighOutputPower 1.3.6.1.2.1.10.133.1.3.8.1.3
The highest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcCurDayLowInputPower 1.3.6.1.2.1.10.133.1.3.8.1.4
The lowest optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcCurDayHighInputPower 1.3.6.1.2.1.10.133.1.3.8.1.5
The highest optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcPrevDayTable 1.3.6.1.2.1.10.133.1.3.9
A table of OTSn source performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOTSnSrcPrevDayEntry

optIfOTSnSrcPrevDayEntry 1.3.6.1.2.1.10.133.1.3.9.1
A conceptual row that contains OTSn source performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOTSnSrcPrevDayEntry  

optIfOTSnSrcPrevDaySuspectedFlag 1.3.6.1.2.1.10.133.1.3.9.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOTSnSrcPrevDayLastOutputPower 1.3.6.1.2.1.10.133.1.3.9.1.2
The last optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcPrevDayLowOutputPower 1.3.6.1.2.1.10.133.1.3.9.1.3
The lowest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcPrevDayHighOutputPower 1.3.6.1.2.1.10.133.1.3.9.1.4
The highest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcPrevDayLastInputPower 1.3.6.1.2.1.10.133.1.3.9.1.5
The last optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcPrevDayLowInputPower 1.3.6.1.2.1.10.133.1.3.9.1.6
The lowest optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTSnSrcPrevDayHighInputPower 1.3.6.1.2.1.10.133.1.3.9.1.7
The highest optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnConfigTable 1.3.6.1.2.1.10.133.1.4.1
A table of OMSn configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOMSnConfigEntry

optIfOMSnConfigEntry 1.3.6.1.2.1.10.133.1.4.1.1
A conceptual row that contains OMSn configuration information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOMSnConfigEntry  

optIfOMSnDirectionality 1.3.6.1.2.1.10.133.1.4.1.1.1
Indicates the directionality of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  OptIfDirectionality  

optIfOMSnCurrentStatus 1.3.6.1.2.1.10.133.1.4.1.1.2
Indicates the defect condition of the entity, if any. This object is applicable only to full capability systems whose interface type is IaDI and for which optIfOMSnDirectionality has the value sink(1) or bidirectional(3).
Status: current Access: read-only
OBJECT-TYPE    
  BITS ssfP(0), ssfO(1), ssf(2), bdiP(3), bdiO(4), bdi(5), losP(6)  

optIfOMSnSinkCurrentTable 1.3.6.1.2.1.10.133.1.4.2
A table of OMSn sink performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOMSnSinkCurrentEntry

optIfOMSnSinkCurrentEntry 1.3.6.1.2.1.10.133.1.4.2.1
A conceptual row that contains OMSn sink performance monitoring information of an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOMSnSinkCurrentEntry  

optIfOMSnSinkCurrentSuspectedFlag 1.3.6.1.2.1.10.133.1.4.2.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOMSnSinkCurrentAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.2.1.2
The aggregated optical power of all the DWDM input channels.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkCurrentLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.2.1.3
The lowest aggregated optical power of all the DWDM input channels during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkCurrentHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.2.1.4
The highest aggregated optical power of all the DWDM input channels during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkCurrentLowerInputPowerThreshold 1.3.6.1.2.1.10.133.1.4.2.1.5
The lower limit threshold on aggregated input power. If optIfOMSnSinkCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkCurrentUpperInputPowerThreshold 1.3.6.1.2.1.10.133.1.4.2.1.6
The upper limit threshold on aggregated input power. If optIfOMSnSinkCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkCurrentOutputPower 1.3.6.1.2.1.10.133.1.4.2.1.7
The optical power monitored at the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkCurrentLowOutputPower 1.3.6.1.2.1.10.133.1.4.2.1.8
The lowest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkCurrentHighOutputPower 1.3.6.1.2.1.10.133.1.4.2.1.9
The highest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkCurrentLowerOutputPowerThreshold 1.3.6.1.2.1.10.133.1.4.2.1.10
The lower limit threshold on output power. If optIfOMSnSinkCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkCurrentUpperOutputPowerThreshold 1.3.6.1.2.1.10.133.1.4.2.1.11
The upper limit threshold on output power. If optIfOMSnSinkCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkIntervalTable 1.3.6.1.2.1.10.133.1.4.3
A table of historical OMSn sink performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOMSnSinkIntervalEntry

optIfOMSnSinkIntervalEntry 1.3.6.1.2.1.10.133.1.4.3.1
A conceptual row that contains OMSn sink performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOMSnSinkIntervalEntry  

optIfOMSnSinkIntervalNumber 1.3.6.1.2.1.10.133.1.4.3.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfIntervalNumber  

optIfOMSnSinkIntervalSuspectedFlag 1.3.6.1.2.1.10.133.1.4.3.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOMSnSinkIntervalLastAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.3.1.3
The last aggregated optical power of all the DWDM input channels during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkIntervalLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.3.1.4
The lowest aggregated optical power of all the DWDM input channels during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkIntervalHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.3.1.5
The highest aggregated optical power of all the DWDM input channels during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkIntervalLastOutputPower 1.3.6.1.2.1.10.133.1.4.3.1.6
The last optical power at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkIntervalLowOutputPower 1.3.6.1.2.1.10.133.1.4.3.1.7
The lowest optical power at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkIntervalHighOutputPower 1.3.6.1.2.1.10.133.1.4.3.1.8
The highest optical power at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkCurDayTable 1.3.6.1.2.1.10.133.1.4.4
A table of OMSn sink performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOMSnSinkCurDayEntry

optIfOMSnSinkCurDayEntry 1.3.6.1.2.1.10.133.1.4.4.1
A conceptual row that contains OMSn sink performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOMSnSinkCurDayEntry  

optIfOMSnSinkCurDaySuspectedFlag 1.3.6.1.2.1.10.133.1.4.4.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOMSnSinkCurDayLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.4.1.2
The lowest aggregated optical power of all the DWDM input channels during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkCurDayHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.4.1.3
The highest aggregated optical power of all the DWDM input channels during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkCurDayLowOutputPower 1.3.6.1.2.1.10.133.1.4.4.1.4
The lowest optical power at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkCurDayHighOutputPower 1.3.6.1.2.1.10.133.1.4.4.1.5
The highest optical power at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkPrevDayTable 1.3.6.1.2.1.10.133.1.4.5
A table of OMSn sink performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOMSnSinkPrevDayEntry

optIfOMSnSinkPrevDayEntry 1.3.6.1.2.1.10.133.1.4.5.1
A conceptual row that contains OMSn sink performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOMSnSinkPrevDayEntry  

optIfOMSnSinkPrevDaySuspectedFlag 1.3.6.1.2.1.10.133.1.4.5.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOMSnSinkPrevDayLastAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.5.1.2
The last aggregated optical power of all the DWDM input channels during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkPrevDayLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.5.1.3
The lowest aggregated optical power of all the DWDM input channels during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkPrevDayHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.5.1.4
The highest aggregated optical power of all the DWDM input channels during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkPrevDayLastOutputPower 1.3.6.1.2.1.10.133.1.4.5.1.5
The last optical power at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkPrevDayLowOutputPower 1.3.6.1.2.1.10.133.1.4.5.1.6
The lowest optical power at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSinkPrevDayHighOutputPower 1.3.6.1.2.1.10.133.1.4.5.1.7
The highest optical power at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcCurrentTable 1.3.6.1.2.1.10.133.1.4.6
A table of OMSn source performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOMSnSrcCurrentEntry

optIfOMSnSrcCurrentEntry 1.3.6.1.2.1.10.133.1.4.6.1
A conceptual row that contains OMSn source performance monitoring information of an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOMSnSrcCurrentEntry  

optIfOMSnSrcCurrentSuspectedFlag 1.3.6.1.2.1.10.133.1.4.6.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOMSnSrcCurrentOutputPower 1.3.6.1.2.1.10.133.1.4.6.1.2
The optical power monitored at the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcCurrentLowOutputPower 1.3.6.1.2.1.10.133.1.4.6.1.3
The lowest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcCurrentHighOutputPower 1.3.6.1.2.1.10.133.1.4.6.1.4
The highest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcCurrentLowerOutputPowerThreshold 1.3.6.1.2.1.10.133.1.4.6.1.5
The lower limit threshold on output power. If optIfOMSnSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcCurrentUpperOutputPowerThreshold 1.3.6.1.2.1.10.133.1.4.6.1.6
The upper limit threshold on output power. If optIfOMSnSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcCurrentAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.6.1.7
The aggregated optical power at the input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcCurrentLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.6.1.8
The lowest aggregated optical power at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcCurrentHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.6.1.9
The highest aggregated optical power at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcCurrentLowerInputPowerThreshold 1.3.6.1.2.1.10.133.1.4.6.1.10
The lower limit threshold on aggregated input power. If optIfOMSnSrcCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcCurrentUpperInputPowerThreshold 1.3.6.1.2.1.10.133.1.4.6.1.11
The upper limit threshold on aggregated input power. If optIfOMSnSrcCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcIntervalTable 1.3.6.1.2.1.10.133.1.4.7
A table of historical OMSn source performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOMSnSrcIntervalEntry

optIfOMSnSrcIntervalEntry 1.3.6.1.2.1.10.133.1.4.7.1
A conceptual row that contains OMSn source performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOMSnSrcIntervalEntry  

optIfOMSnSrcIntervalNumber 1.3.6.1.2.1.10.133.1.4.7.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfIntervalNumber  

optIfOMSnSrcIntervalSuspectedFlag 1.3.6.1.2.1.10.133.1.4.7.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOMSnSrcIntervalLastOutputPower 1.3.6.1.2.1.10.133.1.4.7.1.3
The last optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcIntervalLowOutputPower 1.3.6.1.2.1.10.133.1.4.7.1.4
The lowest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcIntervalHighOutputPower 1.3.6.1.2.1.10.133.1.4.7.1.5
The highest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcIntervalLastAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.7.1.6
The last aggregated optical power at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcIntervalLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.7.1.7
The lowest aggregated optical power at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcIntervalHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.7.1.8
The highest aggregated optical power at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcCurDayTable 1.3.6.1.2.1.10.133.1.4.8
A table of OMSn source performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOMSnSrcCurDayEntry

optIfOMSnSrcCurDayEntry 1.3.6.1.2.1.10.133.1.4.8.1
A conceptual row that contains OMSn source performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOMSnSrcCurDayEntry  

optIfOMSnSrcCurDaySuspectedFlag 1.3.6.1.2.1.10.133.1.4.8.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOMSnSrcCurDayLowOutputPower 1.3.6.1.2.1.10.133.1.4.8.1.2
The lowest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcCurDayHighOutputPower 1.3.6.1.2.1.10.133.1.4.8.1.3
The highest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcCurDayLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.8.1.4
The lowest aggregated optical power at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcCurDayHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.8.1.5
The highest aggregated optical power at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcPrevDayTable 1.3.6.1.2.1.10.133.1.4.9
A table of OMSn source performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOMSnSrcPrevDayEntry

optIfOMSnSrcPrevDayEntry 1.3.6.1.2.1.10.133.1.4.9.1
A conceptual row that contains OMSn source performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOMSnSrcPrevDayEntry  

optIfOMSnSrcPrevDaySuspectedFlag 1.3.6.1.2.1.10.133.1.4.9.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOMSnSrcPrevDayLastOutputPower 1.3.6.1.2.1.10.133.1.4.9.1.2
The last optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcPrevDayLowOutputPower 1.3.6.1.2.1.10.133.1.4.9.1.3
The lowest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcPrevDayHighOutputPower 1.3.6.1.2.1.10.133.1.4.9.1.4
The highest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcPrevDayLastAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.9.1.5
The last aggregated optical power at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcPrevDayLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.9.1.6
The lowest aggregated optical power at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOMSnSrcPrevDayHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.4.9.1.7
The highest aggregated optical power at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupConfigTable 1.3.6.1.2.1.10.133.1.5.1
A table of OChGroup configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChGroupConfigEntry

optIfOChGroupConfigEntry 1.3.6.1.2.1.10.133.1.5.1.1
A conceptual row that contains OChGroup configuration information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChGroupConfigEntry  

optIfOChGroupDirectionality 1.3.6.1.2.1.10.133.1.5.1.1.1
Indicates the directionality of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  OptIfDirectionality  

optIfOChGroupSinkCurrentTable 1.3.6.1.2.1.10.133.1.5.2
A table of OChGroup sink performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChGroupSinkCurrentEntry

optIfOChGroupSinkCurrentEntry 1.3.6.1.2.1.10.133.1.5.2.1
A conceptual row that contains OChGroup sink performance monitoring information of an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChGroupSinkCurrentEntry  

optIfOChGroupSinkCurrentSuspectedFlag 1.3.6.1.2.1.10.133.1.5.2.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChGroupSinkCurrentAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.2.1.2
The aggregated optical power of all the DWDM input channels in the OChGroup.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkCurrentLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.2.1.3
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkCurrentHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.2.1.4
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkCurrentLowerInputPowerThreshold 1.3.6.1.2.1.10.133.1.5.2.1.5
The lower limit threshold on aggregated input power. If optIfOChGroupSinkCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkCurrentUpperInputPowerThreshold 1.3.6.1.2.1.10.133.1.5.2.1.6
The upper limit threshold on aggregated input power. If optIfOChGroupSinkCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkCurrentOutputPower 1.3.6.1.2.1.10.133.1.5.2.1.7
The optical power monitored at the output in the OChGroup.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkCurrentLowOutputPower 1.3.6.1.2.1.10.133.1.5.2.1.8
The lowest optical power monitored at the output in the OChGroup during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkCurrentHighOutputPower 1.3.6.1.2.1.10.133.1.5.2.1.9
The highest optical power monitored at the output in the OChGroup during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkCurrentLowerOutputPowerThreshold 1.3.6.1.2.1.10.133.1.5.2.1.10
The lower limit threshold on the output power. If optIfOChGroupSinkCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkCurrentUpperOutputPowerThreshold 1.3.6.1.2.1.10.133.1.5.2.1.11
The upper limit threshold on the output power. If optIfOChGroupSinkCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkIntervalTable 1.3.6.1.2.1.10.133.1.5.3
A table of historical OChGroup sink performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChGroupSinkIntervalEntry

optIfOChGroupSinkIntervalEntry 1.3.6.1.2.1.10.133.1.5.3.1
A conceptual row that contains OChGroup sink performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChGroupSinkIntervalEntry  

optIfOChGroupSinkIntervalNumber 1.3.6.1.2.1.10.133.1.5.3.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfIntervalNumber  

optIfOChGroupSinkIntervalSuspectedFlag 1.3.6.1.2.1.10.133.1.5.3.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChGroupSinkIntervalLastAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.3.1.3
The last aggregated optical power of all the DWDM input channels in the OChGroup during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkIntervalLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.3.1.4
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkIntervalHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.3.1.5
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkIntervalLastOutputPower 1.3.6.1.2.1.10.133.1.5.3.1.6
The last optical power monitored at the output in the OChGroup during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkIntervalLowOutputPower 1.3.6.1.2.1.10.133.1.5.3.1.7
The lowest optical power monitored at the output in the OChGroup during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkIntervalHighOutputPower 1.3.6.1.2.1.10.133.1.5.3.1.8
The highest optical power monitored at the output in the OChGroup during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkCurDayTable 1.3.6.1.2.1.10.133.1.5.4
A table of OChGroup sink performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChGroupSinkCurDayEntry

optIfOChGroupSinkCurDayEntry 1.3.6.1.2.1.10.133.1.5.4.1
A conceptual row that contains OChGroup sink performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChGroupSinkCurDayEntry  

optIfOChGroupSinkCurDaySuspectedFlag 1.3.6.1.2.1.10.133.1.5.4.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChGroupSinkCurDayLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.4.1.2
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkCurDayHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.4.1.3
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkCurDayLowOutputPower 1.3.6.1.2.1.10.133.1.5.4.1.4
The lowest optical power monitored at the output in the OChGroup during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkCurDayHighOutputPower 1.3.6.1.2.1.10.133.1.5.4.1.5
The highest optical power monitored at the output in the OChGroup during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkPrevDayTable 1.3.6.1.2.1.10.133.1.5.5
A table of OChGroup sink performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChGroupSinkPrevDayEntry

optIfOChGroupSinkPrevDayEntry 1.3.6.1.2.1.10.133.1.5.5.1
A conceptual row that contains OChGroup sink performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChGroupSinkPrevDayEntry  

optIfOChGroupSinkPrevDaySuspectedFlag 1.3.6.1.2.1.10.133.1.5.5.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChGroupSinkPrevDayLastAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.5.1.2
The last aggregated optical power of all the DWDM input channels in the OChGroup during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkPrevDayLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.5.1.3
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkPrevDayHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.5.1.4
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkPrevDayLastOutputPower 1.3.6.1.2.1.10.133.1.5.5.1.5
The last optical power monitored at the output in the OChGroup during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkPrevDayLowOutputPower 1.3.6.1.2.1.10.133.1.5.5.1.6
The lowest optical power monitored at the output in the OChGroup during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSinkPrevDayHighOutputPower 1.3.6.1.2.1.10.133.1.5.5.1.7
The highest optical power monitored at the output in the OChGroup during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcCurrentTable 1.3.6.1.2.1.10.133.1.5.6
A table of OChGroup source performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChGroupSrcCurrentEntry

optIfOChGroupSrcCurrentEntry 1.3.6.1.2.1.10.133.1.5.6.1
A conceptual row that contains OChGroup source performance monitoring information of an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChGroupSrcCurrentEntry  

optIfOChGroupSrcCurrentSuspectedFlag 1.3.6.1.2.1.10.133.1.5.6.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChGroupSrcCurrentOutputPower 1.3.6.1.2.1.10.133.1.5.6.1.2
The optical power monitored at the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcCurrentLowOutputPower 1.3.6.1.2.1.10.133.1.5.6.1.3
The lowest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcCurrentHighOutputPower 1.3.6.1.2.1.10.133.1.5.6.1.4
The highest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcCurrentLowerOutputPowerThreshold 1.3.6.1.2.1.10.133.1.5.6.1.5
The lower limit threshold on output power. If optIfOChGroupSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcCurrentUpperOutputPowerThreshold 1.3.6.1.2.1.10.133.1.5.6.1.6
The upper limit threshold on output power. If optIfOChGroupSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcCurrentAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.6.1.7
The aggregated optical power monitored at the input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcCurrentLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.6.1.8
The lowest aggregated optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcCurrentHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.6.1.9
The highest aggregated optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcCurrentLowerInputPowerThreshold 1.3.6.1.2.1.10.133.1.5.6.1.10
The lower limit threshold on input power. If optIfOChGroupSrcCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcCurrentUpperInputPowerThreshold 1.3.6.1.2.1.10.133.1.5.6.1.11
The upper limit threshold on input power. If optIfOChGroupSrcCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcIntervalTable 1.3.6.1.2.1.10.133.1.5.7
A table of historical OChGroup source performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChGroupSrcIntervalEntry

optIfOChGroupSrcIntervalEntry 1.3.6.1.2.1.10.133.1.5.7.1
A conceptual row that contains OChGroup source performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChGroupSrcIntervalEntry  

optIfOChGroupSrcIntervalNumber 1.3.6.1.2.1.10.133.1.5.7.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfIntervalNumber  

optIfOChGroupSrcIntervalSuspectedFlag 1.3.6.1.2.1.10.133.1.5.7.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChGroupSrcIntervalLastOutputPower 1.3.6.1.2.1.10.133.1.5.7.1.3
The last optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcIntervalLowOutputPower 1.3.6.1.2.1.10.133.1.5.7.1.4
The lowest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcIntervalHighOutputPower 1.3.6.1.2.1.10.133.1.5.7.1.5
The highest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcIntervalLastAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.7.1.6
The last aggregated optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcIntervalLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.7.1.7
The lowest aggregated optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcIntervalHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.7.1.8
The highest aggregated optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcCurDayTable 1.3.6.1.2.1.10.133.1.5.8
A table of OChGroup source performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChGroupSrcCurDayEntry

optIfOChGroupSrcCurDayEntry 1.3.6.1.2.1.10.133.1.5.8.1
A conceptual row that contains OChGroup source performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChGroupSrcCurDayEntry  

optIfOChGroupSrcCurDaySuspectedFlag 1.3.6.1.2.1.10.133.1.5.8.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChGroupSrcCurDayLowOutputPower 1.3.6.1.2.1.10.133.1.5.8.1.2
The lowest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcCurDayHighOutputPower 1.3.6.1.2.1.10.133.1.5.8.1.3
The highest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcCurDayLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.8.1.4
The lowest aggregated optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcCurDayHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.8.1.5
The highest aggregated optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcPrevDayTable 1.3.6.1.2.1.10.133.1.5.9
A table of OChGroup source performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChGroupSrcPrevDayEntry

optIfOChGroupSrcPrevDayEntry 1.3.6.1.2.1.10.133.1.5.9.1
A conceptual row that contains OChGroup source performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChGroupSrcPrevDayEntry  

optIfOChGroupSrcPrevDaySuspectedFlag 1.3.6.1.2.1.10.133.1.5.9.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChGroupSrcPrevDayLastOutputPower 1.3.6.1.2.1.10.133.1.5.9.1.2
The last optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcPrevDayLowOutputPower 1.3.6.1.2.1.10.133.1.5.9.1.3
The lowest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcPrevDayHighOutputPower 1.3.6.1.2.1.10.133.1.5.9.1.4
The highest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcPrevDayLastAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.9.1.5
The last aggregated optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcPrevDayLowAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.9.1.6
The lowest aggregated optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChGroupSrcPrevDayHighAggregatedInputPower 1.3.6.1.2.1.10.133.1.5.9.1.7
The highest aggregated optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChConfigTable 1.3.6.1.2.1.10.133.1.6.1
A table of OCh configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChConfigEntry

optIfOChConfigEntry 1.3.6.1.2.1.10.133.1.6.1.1
A conceptual row that contains OCh configuration information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChConfigEntry  

optIfOChDirectionality 1.3.6.1.2.1.10.133.1.6.1.1.1
Indicates the directionality of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  OptIfDirectionality  

optIfOChCurrentStatus 1.3.6.1.2.1.10.133.1.6.1.1.2
Indicates the defect condition of the entity, if any. This object is applicable when optIfOChDirectionality has the value sink(1) or bidirectional(3). In full-capability systems the bit position los(1) is not used. In reduced-capability systems or at IrDI interfaces only the bit positions los(1) and ssfP(3) are used.
Status: current Access: read-only
OBJECT-TYPE    
  BITS losP(0), los(1), oci(2), ssfP(3), ssfO(4), ssf(5)  

optIfOChSinkCurrentTable 1.3.6.1.2.1.10.133.1.6.2
A table of OCh sink performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChSinkCurrentEntry

optIfOChSinkCurrentEntry 1.3.6.1.2.1.10.133.1.6.2.1
A conceptual row that contains OCh sink performance monitoring information for an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChSinkCurrentEntry  

optIfOChSinkCurrentSuspectedFlag 1.3.6.1.2.1.10.133.1.6.2.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChSinkCurrentInputPower 1.3.6.1.2.1.10.133.1.6.2.1.2
The optical power monitored at the input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSinkCurrentLowInputPower 1.3.6.1.2.1.10.133.1.6.2.1.3
The lowest optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSinkCurrentHighInputPower 1.3.6.1.2.1.10.133.1.6.2.1.4
The highest optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSinkCurrentLowerInputPowerThreshold 1.3.6.1.2.1.10.133.1.6.2.1.5
The lower limit threshold on input power. If optIfOChSinkCurrentInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOChSinkCurrentUpperInputPowerThreshold 1.3.6.1.2.1.10.133.1.6.2.1.6
The upper limit threshold on input power. If optIfOChSinkCurrentInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOChSinkIntervalTable 1.3.6.1.2.1.10.133.1.6.3
A table of historical OCh sink performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChSinkIntervalEntry

optIfOChSinkIntervalEntry 1.3.6.1.2.1.10.133.1.6.3.1
A conceptual row that contains OCh sink performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChSinkIntervalEntry  

optIfOChSinkIntervalNumber 1.3.6.1.2.1.10.133.1.6.3.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfIntervalNumber  

optIfOChSinkIntervalSuspectedFlag 1.3.6.1.2.1.10.133.1.6.3.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChSinkIntervalLastInputPower 1.3.6.1.2.1.10.133.1.6.3.1.3
The last optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSinkIntervalLowInputPower 1.3.6.1.2.1.10.133.1.6.3.1.4
The lowest optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSinkIntervalHighInputPower 1.3.6.1.2.1.10.133.1.6.3.1.5
The highest optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSinkCurDayTable 1.3.6.1.2.1.10.133.1.6.4
A table of OCh sink performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChSinkCurDayEntry

optIfOChSinkCurDayEntry 1.3.6.1.2.1.10.133.1.6.4.1
A conceptual row that contains OCh sink performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChSinkCurDayEntry  

optIfOChSinkCurDaySuspectedFlag 1.3.6.1.2.1.10.133.1.6.4.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChSinkCurDayLowInputPower 1.3.6.1.2.1.10.133.1.6.4.1.2
The lowest optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSinkCurDayHighInputPower 1.3.6.1.2.1.10.133.1.6.4.1.3
The highest optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSinkPrevDayTable 1.3.6.1.2.1.10.133.1.6.5
A table of OCh sink performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChSinkPrevDayEntry

optIfOChSinkPrevDayEntry 1.3.6.1.2.1.10.133.1.6.5.1
A conceptual row that contains OCh sink performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChSinkPrevDayEntry  

optIfOChSinkPrevDaySuspectedFlag 1.3.6.1.2.1.10.133.1.6.5.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChSinkPrevDayLastInputPower 1.3.6.1.2.1.10.133.1.6.5.1.2
The last optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSinkPrevDayLowInputPower 1.3.6.1.2.1.10.133.1.6.5.1.3
The lowest optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSinkPrevDayHighInputPower 1.3.6.1.2.1.10.133.1.6.5.1.4
The highest optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSrcCurrentTable 1.3.6.1.2.1.10.133.1.6.6
A table of OCh source performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChSrcCurrentEntry

optIfOChSrcCurrentEntry 1.3.6.1.2.1.10.133.1.6.6.1
A conceptual row that contains OCh source performance monitoring information of an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChSrcCurrentEntry  

optIfOChSrcCurrentSuspectedFlag 1.3.6.1.2.1.10.133.1.6.6.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChSrcCurrentOutputPower 1.3.6.1.2.1.10.133.1.6.6.1.2
The optical power monitored at the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSrcCurrentLowOutputPower 1.3.6.1.2.1.10.133.1.6.6.1.3
The lowest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSrcCurrentHighOutputPower 1.3.6.1.2.1.10.133.1.6.6.1.4
The highest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSrcCurrentLowerOutputPowerThreshold 1.3.6.1.2.1.10.133.1.6.6.1.5
The lower limit threshold on output power. If optIfOChSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOChSrcCurrentUpperOutputPowerThreshold 1.3.6.1.2.1.10.133.1.6.6.1.6
The upper limit threshold on output power. If optIfOChSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

optIfOChSrcIntervalTable 1.3.6.1.2.1.10.133.1.6.7
A table of historical OCh source performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChSrcIntervalEntry

optIfOChSrcIntervalEntry 1.3.6.1.2.1.10.133.1.6.7.1
A conceptual row that contains OCh source performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChSrcIntervalEntry  

optIfOChSrcIntervalNumber 1.3.6.1.2.1.10.133.1.6.7.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfIntervalNumber  

optIfOChSrcIntervalSuspectedFlag 1.3.6.1.2.1.10.133.1.6.7.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChSrcIntervalLastOutputPower 1.3.6.1.2.1.10.133.1.6.7.1.3
The last optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSrcIntervalLowOutputPower 1.3.6.1.2.1.10.133.1.6.7.1.4
The lowest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSrcIntervalHighOutputPower 1.3.6.1.2.1.10.133.1.6.7.1.5
The highest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSrcCurDayTable 1.3.6.1.2.1.10.133.1.6.8
A table of OCh source performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChSrcCurDayEntry

optIfOChSrcCurDayEntry 1.3.6.1.2.1.10.133.1.6.8.1
A conceptual row that contains OCh source performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChSrcCurDayEntry  

optIfOChSrcCurDaySuspectedFlag 1.3.6.1.2.1.10.133.1.6.8.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChSrcCurDayLowOutputPower 1.3.6.1.2.1.10.133.1.6.8.1.2
The lowest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSrcCurDayHighOutputPower 1.3.6.1.2.1.10.133.1.6.8.1.3
The highest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSrcPrevDayTable 1.3.6.1.2.1.10.133.1.6.9
A table of OCh source performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOChSrcPrevDayEntry

optIfOChSrcPrevDayEntry 1.3.6.1.2.1.10.133.1.6.9.1
A conceptual row that contains OCh source performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOChSrcPrevDayEntry  

optIfOChSrcPrevDaySuspectedFlag 1.3.6.1.2.1.10.133.1.6.9.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfOChSrcPrevDayLastOutputPower 1.3.6.1.2.1.10.133.1.6.9.1.2
The last optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSrcPrevDayLowOutputPower 1.3.6.1.2.1.10.133.1.6.9.1.3
The lowest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOChSrcPrevDayHighOutputPower 1.3.6.1.2.1.10.133.1.6.9.1.4
The highest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

optIfOTUkConfigTable 1.3.6.1.2.1.10.133.1.7.1
A table of OTUk configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfOTUkConfigEntry

optIfOTUkConfigEntry 1.3.6.1.2.1.10.133.1.7.1.1
A conceptual row that contains OTUk configuration information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfOTUkConfigEntry  

optIfOTUkDirectionality 1.3.6.1.2.1.10.133.1.7.1.1.1
Indicates the directionality of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  OptIfDirectionality  

optIfOTUkBitRateK 1.3.6.1.2.1.10.133.1.7.1.1.2
Indicates the bit rate of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  OptIfBitRateK  

optIfOTUkTraceIdentifierTransmitted 1.3.6.1.2.1.10.133.1.7.1.1.3
The trace identifier transmitted. This object is applicable when optIfOTUkDirectionality has the value source(2) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value sink(1). If no value is ever set by a management entity for this object, system-specific default value will be used. Any implementation that instantiates this object must document the system-specific default value or how it is derived.
Status: current Access: read-write
OBJECT-TYPE    
  OptIfTxTI  

optIfOTUkDAPIExpected 1.3.6.1.2.1.10.133.1.7.1.1.4
The DAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). This object has no effect when optIfOTUkTIMDetMode has the value off(1).
Status: current Access: read-write
OBJECT-TYPE    
  OptIfExDAPI  

optIfOTUkSAPIExpected 1.3.6.1.2.1.10.133.1.7.1.1.5
The SAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). This object has no effect when optIfOTUkTIMDetMode has the value off(1).
Status: current Access: read-write
OBJECT-TYPE    
  OptIfExSAPI  

optIfOTUkTraceIdentifierAccepted 1.3.6.1.2.1.10.133.1.7.1.1.6
The actual trace identifier accepted. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). The value of this object is unspecified when optIfOTUkCurrentStatus indicates a near-end defect (i.e., ssf(3), lof(4), ais(5), lom(6)) that prevents extraction of the trace message.
Status: current Access: read-only
OBJECT-TYPE    
  OptIfAcTI  

optIfOTUkTIMDetMode 1.3.6.1.2.1.10.133.1.7.1.1.7
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). The default value of this object is off(1).
Status: current Access: read-write
OBJECT-TYPE    
  OptIfTIMDetMode  

optIfOTUkTIMActEnabled 1.3.6.1.2.1.10.133.1.7.1.1.8
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). This object has no effect when optIfOTUkTIMDetMode has the value off(1). The default value of this object is false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

optIfOTUkDEGThr 1.3.6.1.2.1.10.133.1.7.1.1.9
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to optIfOTUkDEGThr. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). The default value of this object is Severely Errored Second (SES) Estimator (See ITU-T G.7710).
Status: current Access: read-write
OBJECT-TYPE    
  OptIfDEGThr  

optIfOTUkDEGM 1.3.6.1.2.1.10.133.1.7.1.1.10
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if optIfOTUkDEGM consecutive bad PM Seconds are detected. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). The default value of this object is 7 (See ITU-T G.7710).
Status: current Access: read-write
OBJECT-TYPE    
  OptIfDEGM  

optIfOTUkSinkAdaptActive 1.3.6.1.2.1.10.133.1.7.1.1.11
Indicates whether the sink adaptation function is activated or not. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). The default value of this object is false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

optIfOTUkSourceAdaptActive 1.3.6.1.2.1.10.133.1.7.1.1.12
Indicates whether the source adaptation function is activated or not. This object is only applicable to the source function, i.e., only when optIfOTUkDirectionality has the value source(2) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value sink(1). The default value of this object is false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

optIfOTUkSinkFECEnabled 1.3.6.1.2.1.10.133.1.7.1.1.13
If Forward Error Correction (FEC) is supported, this object indicates whether FEC at the OTUk sink adaptation function is enabled or not. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). The default value of this object is true(1).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

optIfOTUkCurrentStatus 1.3.6.1.2.1.10.133.1.7.1.1.14
Indicates the defect condition of the entity, if any. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2).
Status: current Access: read-only
OBJECT-TYPE    
  BITS tim(0), deg(1), bdi(2), ssf(3), lof(4), ais(5), lom(6)  

optIfGCC0ConfigTable 1.3.6.1.2.1.10.133.1.7.2
A table of GCC0 configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfGCC0ConfigEntry

optIfGCC0ConfigEntry 1.3.6.1.2.1.10.133.1.7.2.1
A conceptual row that contains GCC0 configuration information of an interface. Each instance must correspond to an instance of optIfOTUkConfigEntry. Separate source and/or sink instances may exist for a given ifIndex value, or a single bidirectional instance may exist, but a bidirectional instance may not coexist with a source or sink instance. Instances of this conceptual row persist across agent restarts.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfGCC0ConfigEntry  

optIfGCC0Directionality 1.3.6.1.2.1.10.133.1.7.2.1.1
Indicates the directionality of the entity. The values source(2) and bidirectional(3) are not allowed if the corresponding instance of optIfOTUkDirectionality has the value sink(1). The values sink(1) and bidirectional(3) are not allowed if the corresponding instance of optIfOTUkDirectionality has the value source(2).
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfDirectionality  

optIfGCC0Application 1.3.6.1.2.1.10.133.1.7.2.1.2
Indicates the application transported by the GCC0 entity. Example applications are ECC, User data channel. The value of this object may not be changed when optIfGCC0RowStatus has the value active(1).
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

optIfGCC0RowStatus 1.3.6.1.2.1.10.133.1.7.2.1.3
This columnar object is used for creating and deleting a conceptual row of the optIfGCC0 config table. It is used to model the addGCC0Access and removeGCC0Access operations of an OTUk_TTP for GCC0 access control as defined in G.874.1. Setting RowStatus to createAndGo or createAndWait implies addGCC0Access. Setting RowStatus to destroy implies removeGCC0Access.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

optIfODUkConfigTable 1.3.6.1.2.1.10.133.1.8.1
A table of ODUk configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfODUkConfigEntry

optIfODUkConfigEntry 1.3.6.1.2.1.10.133.1.8.1.1
A conceptual row that contains ODUk configuration information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfODUkConfigEntry  

optIfODUkDirectionality 1.3.6.1.2.1.10.133.1.8.1.1.1
Indicates the directionality of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  OptIfDirectionality  

optIfODUkBitRateK 1.3.6.1.2.1.10.133.1.8.1.1.2
Indicates the bit rate of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  OptIfBitRateK  

optIfODUkTcmFieldsInUse 1.3.6.1.2.1.10.133.1.8.1.1.3
Indicates the TCM field(s) that are currently in use. The positions of the bits correspond to the TCM fields. A bit that is set to 1 means that the corresponding TCM field is used. This object will be updated when rows are created in or deleted from the optIfODUkTConfigTable, or the optIfODUkTNimConfigTable.
Status: current Access: read-only
OBJECT-TYPE    
  BITS tcmField1(0), tcmField2(1), tcmField3(2), tcmField4(3), tcmField5(4), tcmField6(5)  

optIfODUkPositionSeqCurrentSize 1.3.6.1.2.1.10.133.1.8.1.1.4
This variable indicates the current size of the position sequence (i.e., number of TCM function and/or GCC12 access that have been created in the ODUk interface). When the value of this variable is greater than zero, it means that one or more TCM function and/or GCC12 access have been created in the ODUk interface. In this case, there will be as many rows in the optIfODUkPositionSeqTable as the value of optIfODUkPositionSeqCurrentSize corresponding to this ODUk interface, one row for each TCM function or GCC12 access. The position of the TCM function and/or GCC12 access within the sequence is indicated by the optIfODUkPositionSeqPosition variable in optIfODUkPositionSeqTable. The optIfODUkPositionSeqTable also provides pointers to the corresponding TCM function (optIfODUkT) and GCC12 access (optIfGCC12) entities.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

optIfODUkTtpPresent 1.3.6.1.2.1.10.133.1.8.1.1.5
This object has the value true(1) if the ifEntry under which it is instantiated contains an ODUk Trail Termination Point, i.e., is the endpoint of an ODUk path. In that case there will be a corresponding row in the ODUk TTP config table and it will not be possible to create corresponding rows in the ODUk NIM config table. This object has the value false(2) if the ifEntry under which it is instantiated contains an intermediate ODUk Connection Termination Point. In that case there is no corresponding row in the ODUk TTP config table, but it will be possible to create corresponding rows in the ODUk NIM config table. This object also affects the allowable options in rows created in the GCC12 config table and in the ODUkT config table, as specified in the DESCRIPTION clauses of the columns in those tables.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

optIfODUkTtpConfigTable 1.3.6.1.2.1.10.133.1.8.2
A table of ODUk TTP configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfODUkTtpConfigEntry

optIfODUkTtpConfigEntry 1.3.6.1.2.1.10.133.1.8.2.1
A conceptual row that contains ODUk TTP configuration information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfODUkTtpConfigEntry  

optIfODUkTtpTraceIdentifierTransmitted 1.3.6.1.2.1.10.133.1.8.2.1.1
The trace identifier transmitted. This object is applicable when optIfODUkDirectionality has the value source(2) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value sink(1). If no value is ever set by a management entity for this object, system-specific default value will be used. Any implementation that instantiates this object must document the system-specific default value or how it is derived.
Status: current Access: read-write
OBJECT-TYPE    
  OptIfTxTI  

optIfODUkTtpDAPIExpected 1.3.6.1.2.1.10.133.1.8.2.1.2
The DAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2). This object has no effect when optIfODUkTtpTIMDetMode has the value off(1).
Status: current Access: read-write
OBJECT-TYPE    
  OptIfExDAPI  

optIfODUkTtpSAPIExpected 1.3.6.1.2.1.10.133.1.8.2.1.3
The SAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2). This object has no effect when optIfODUkTtpTIMDetMode has the value off(1).
Status: current Access: read-write
OBJECT-TYPE    
  OptIfExSAPI  

optIfODUkTtpTraceIdentifierAccepted 1.3.6.1.2.1.10.133.1.8.2.1.4
The actual trace identifier accepted. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2). The value of this object is unspecified when optIfODUkTtpCurrentStatus indicates a near-end defect (i.e., oci(0), lck(1), ssf(5)) that prevents extraction of the trace message.
Status: current Access: read-only
OBJECT-TYPE    
  OptIfAcTI  

optIfODUkTtpTIMDetMode 1.3.6.1.2.1.10.133.1.8.2.1.5
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2). The default value of this object is off(1).
Status: current Access: read-write
OBJECT-TYPE    
  OptIfTIMDetMode  

optIfODUkTtpTIMActEnabled 1.3.6.1.2.1.10.133.1.8.2.1.6
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2). This object has no effect when optIfODUkTtpTIMDetMode has the value off(1). The default value of this object is false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

optIfODUkTtpDEGThr 1.3.6.1.2.1.10.133.1.8.2.1.7
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to optIfODUkDEGThr. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2). The default value of this object is Severely Errored Second (SES) Estimator (See ITU-T G.7710).
Status: current Access: read-write
OBJECT-TYPE    
  OptIfDEGThr  

optIfODUkTtpDEGM 1.3.6.1.2.1.10.133.1.8.2.1.8
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if optIfODUkDEGM consecutive bad PM Seconds are detected. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2). The default value of this object is 7 (See ITU-T G.7710).
Status: current Access: read-write
OBJECT-TYPE    
  OptIfDEGM  

optIfODUkTtpCurrentStatus 1.3.6.1.2.1.10.133.1.8.2.1.9
Indicates the defect condition of the entity, if any. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2).
Status: current Access: read-only
OBJECT-TYPE    
  BITS oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)  

optIfODUkPositionSeqTable 1.3.6.1.2.1.10.133.1.8.3
A table of ODUk Position Sequence information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfODUkPositionSeqEntry

optIfODUkPositionSeqEntry 1.3.6.1.2.1.10.133.1.8.3.1
A conceptual row that contains ODUk position sequence information of an ODUk interface. The ODUk interface is identified by the ifIndex. Associated with each ODUk interface there may be one of more conceptual rows in the optIfODUkPositionSeqTable. Each row represents a TCM or GCC12 access function within the associated ODUk interface. Rows of the optIfODUkPositionSeqTable table are created/deleted as the result of the creation/deletion of the optIfODUkT or optIfGCC12 entities.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfODUkPositionSeqEntry  

optIfODUkPositionSeqIndex 1.3.6.1.2.1.10.133.1.8.3.1.1
This variable identifies a row in the optIfODUkPositionSeqTable Table. Each row of the optIfODUkPositionSeqTable Table represents a TCM or GCC12 access function within the associated ODUk interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

optIfODUkPositionSeqPosition 1.3.6.1.2.1.10.133.1.8.3.1.2
This variable indicates the position of the TCM or GCC12 access function within the sequence of TCMs & GCC12 access functions of the associated ODUk interface. The TCM or GCC12 presented by this row is referenced by the optIfODUkPositionSeqPointer variable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

optIfODUkPositionSeqPointer 1.3.6.1.2.1.10.133.1.8.3.1.3
This variable identifies the TCM or GCC12 access function by pointing to the corresponding optIfODUkT or optIfGCC12 entity.
Status: current Access: read-only
OBJECT-TYPE    
  RowPointer  

optIfODUkNimConfigTable 1.3.6.1.2.1.10.133.1.8.4
A table of ODUkNim configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfODUkNimConfigEntry

optIfODUkNimConfigEntry 1.3.6.1.2.1.10.133.1.8.4.1
A conceptual row that contains ODUkNim configuration information of an interface. Each instance must correspond to an instance of optIfODUkConfigEntry for which optIfODUkTtpPresent has the value false(2). Instances of this conceptual row persist across agent restarts, and read-create columns other than the status column may be modified while the row is active.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfODUkNimConfigEntry  

optIfODUkNimDirectionality 1.3.6.1.2.1.10.133.1.8.4.1.1
Specifies the monitor point for the ODUk Path non-intrusive monitoring function. The value source(2) is not allowed if the corresponding instance of optIfODUkDirectionality has the value sink(1), and the value sink(1) is not allowed if the corresponding instance of optIfODUkDirectionality has the value source(2). Either the value sink(1) or source(2) is allowed if the corresponding instance of optIfODUkDirectionality has the value bidirectional(3). The value sink(1) means monitoring at the sink direction path signal of the ODUk CTP. The value source(2) means monitoring at the source direction path signal of the ODUk CTP. Monitoring the source direction of an ODUk CTP is necessary in those cases where the ODUk CTP is at an SNCP (Subnetwork Connection Protection) end (e.g., see Figure I.1.2/G.874.1). If one would like to get the performance of the protected connection, one cannot use the NIM function at both ODUk CTP sinks (before the matrix), instead one should monitor the signal at the source ODUk CTP after the matrix.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfSinkOrSource  

optIfODUkNimDAPIExpected 1.3.6.1.2.1.10.133.1.8.4.1.2
The DAPI expected by the receiver. This object has no effect if optIfODUkNimTIMDetMode has the value off(1) or sapi(3).
Status: current Access: read-create
OBJECT-TYPE    
  OptIfExDAPI  

optIfODUkNimSAPIExpected 1.3.6.1.2.1.10.133.1.8.4.1.3
The SAPI expected by the receiver. This object has no effect if optIfODUkNimTIMDetMode has the value off(1) or dapi(2).
Status: current Access: read-create
OBJECT-TYPE    
  OptIfExSAPI  

optIfODUkNimTraceIdentifierAccepted 1.3.6.1.2.1.10.133.1.8.4.1.4
The actual trace identifier accepted. The value of this object is unspecified if optIfODUkNimCurrentStatus has any of the bit positions oci(0), lck(1), or ssf(5) set or if optIfODUkNimRowStatus has any value other than active(1).
Status: current Access: read-only
OBJECT-TYPE    
  OptIfAcTI  

optIfODUkNimTIMDetMode 1.3.6.1.2.1.10.133.1.8.4.1.5
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function.
Status: current Access: read-create
OBJECT-TYPE    
  OptIfTIMDetMode  

optIfODUkNimTIMActEnabled 1.3.6.1.2.1.10.133.1.8.4.1.6
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

optIfODUkNimDEGThr 1.3.6.1.2.1.10.133.1.8.4.1.7
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to optIfODUkNimDEGThr.
Status: current Access: read-create
OBJECT-TYPE    
  OptIfDEGThr  

optIfODUkNimDEGM 1.3.6.1.2.1.10.133.1.8.4.1.8
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if optIfODUkNimDEGM consecutive bad PM Seconds are detected.
Status: current Access: read-create
OBJECT-TYPE    
  OptIfDEGM  

optIfODUkNimCurrentStatus 1.3.6.1.2.1.10.133.1.8.4.1.9
Indicates the defect condition of the entity, if any. The value of this object is unspecified if optIfODUkNimRowStatus has any value other than active(1).
Status: current Access: read-only
OBJECT-TYPE    
  BITS oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)  

optIfODUkNimRowStatus 1.3.6.1.2.1.10.133.1.8.4.1.10
This columnar object is used for creating and deleting a conceptual row of the optIfODUkNim config table. It is used to model the activateNim and deactivateNim operations of an OTUk_CTP for non-intrusive monitoring control as defined in G.874.1. Setting RowStatus to createAndGo or createAndWait implies activateNim. Setting RowStatus to destroy implies deactivateNim.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

optIfGCC12ConfigTable 1.3.6.1.2.1.10.133.1.8.5
A table of GCC12 configuration information. The GCC function processes the GCC overhead bytes passing through them but leave the remainder of the ODUk overhead and payload data alone.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfGCC12ConfigEntry

optIfGCC12ConfigEntry 1.3.6.1.2.1.10.133.1.8.5.1
A conceptual row that contains GCC12 configuration information of an interface. Each instance must correspond to an instance of optIfODUkConfigEntry. Separate instances providing GCC1-only access and GCC2-only access may exist for a given ifIndex value, or a single instance providing GCC1 + GCC2 may exist, but a GCC1 + GCC2 instance may not coexist with a GCC1-only or GCC2-only instance. Instances of this conceptual row persist across agent restarts.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfGCC12ConfigEntry  

optIfGCC12Codirectional 1.3.6.1.2.1.10.133.1.8.5.1.1
Indicates the directionality of the GCC12 termination with respect to the associated ODUk CTP. The value true(1) means that the sink part of the GCC12 extracts COMMS data from the signal at the input to the ODUk CTP sink and the source part of the GCC12 inserts COMMS data into the signal at the output of the ODUk CTP source. The value false(2) means that the sink part of the GCC12 extracts COMMS data from the signal at the output of the ODUk CTP source and the source part of the GCC12 inserts COMMS data into the signal at the input of the ODUk CTP sink. This attribute may assume either value when the corresponding instance of optIfODUkTtpPresent has the value false(2). When the value of the corresponding instance of optIfODUkTtpPresent is true(1) then the only value allowed for this attribute is true(1).
Status: current Access: not-accessible
OBJECT-TYPE    
  TruthValue  

optIfGCC12GCCAccess 1.3.6.1.2.1.10.133.1.8.5.1.2
Indicates the GCC access represented by the entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER gcc1(1), gcc2(2), gcc1and2(3)  

optIfGCC12GCCPassThrough 1.3.6.1.2.1.10.133.1.8.5.1.3
Controls whether the selected GCC overhead bytes are passed through or modified. The value true(1) means that the selected GCC overhead bytes are passed through unmodified from the ODUk CTP input to the ODUk CTP output. The value false(2) means that the selected GCC overhead bytes are set to zero at the ODUk CTP output after the extraction of the COMMS data. This object has no effect if the corresponding instance of optIfODUkTtpPresent has the value true(1). The value of this object may not be changed when optIfGCC12RowStatus has the value active(1).
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

optIfGCC12Application 1.3.6.1.2.1.10.133.1.8.5.1.4
Indicates the application transported by the GCC12 entity. Example applications are ECC, User data channel. The value of this object may not be changed when optIfGCC12RowStatus has the value active(1).
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

optIfGCC12RowStatus 1.3.6.1.2.1.10.133.1.8.5.1.5
This columnar object is used for creating and deleting a conceptual row of the optIfGCC12 config table. It is used to model the addGCC12Access and removeGCC12Access operations of an ODUk_CTP or ODUk_TTP for GCC12 access control as defined in G.874.1. Setting RowStatus to createAndGo or createAndWait implies addGCC12Access. Setting RowStatus to destroy implies removeGCC12Access. Successful addition/removal of the GCC12 access function will result in updating the optIfODUkPositionSeqCurrentSize variable and the optIfODUkPositionSeqTable table of the associated ODUk entry in the optIfODUkConfigTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

optIfODUkTConfigTable 1.3.6.1.2.1.10.133.1.9.1
A table of ODUkT configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfODUkTConfigEntry

optIfODUkTConfigEntry 1.3.6.1.2.1.10.133.1.9.1.1
A conceptual row that contains ODUkT configuration information of an interface. Each instance must correspond to an instance of optIfODUkConfigEntry. Rows in this table are mutually exclusive with rows in the ODUkT NIM config table -- in other words, this row object may not be instantiated for a given pair of ifIndex and TCM field values if a corresponding instance of optIfODUkTNimConfigEntry already exists. Instances of this conceptual row persist across agent restarts. Except where noted otherwise, read-create columns other than the status column may be modified while the row is active.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfODUkTConfigEntry  

optIfODUkTTcmField 1.3.6.1.2.1.10.133.1.9.1.1.1
Indicates the tandem connection monitoring field of the ODUk OH. Valid values are integers from 1 to 6.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..6  

optIfODUkTCodirectional 1.3.6.1.2.1.10.133.1.9.1.1.2
Indicates the directionality of the ODUkT termination point with respect to the associated ODUk CTP. The value true(1) means that the sink part of the ODUkT TP extracts TCM data from the signal at the input to the ODUk CTP sink and the source part of the ODUkT TP inserts TCM data into the signal at the output of the ODUk CTP source. The value false(2) means that the sink part of the ODUkT TP extracts TCM data from the signal at the output of the ODUk CTP source and the source part of the ODUkT TP inserts TCM data into the signal at the input of the ODUk CTP sink. This attribute may assume either value when the corresponding instance of optIfODUkTtpPresent has the value false(2). When the value of the corresponding instance of optIfODUkTtpPresent is true(1) then the only value allowed for this attribute is true(1).
Status: current Access: not-accessible
OBJECT-TYPE    
  TruthValue  

optIfODUkTTraceIdentifierTransmitted 1.3.6.1.2.1.10.133.1.9.1.1.3
The trace identifier transmitted. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value false(2), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value true(1). It must not be instantiated in rows for all other cases.
Status: current Access: read-create
OBJECT-TYPE    
  OptIfTxTI  

optIfODUkTDAPIExpected 1.3.6.1.2.1.10.133.1.9.1.1.4
The DAPI expected by the receiver. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. This object has no effect when optIfODUkTTIMDetMode has the value off(1).
Status: current Access: read-create
OBJECT-TYPE    
  OptIfExDAPI  

optIfODUkTSAPIExpected 1.3.6.1.2.1.10.133.1.9.1.1.5
The SAPI expected by the receiver. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. This object has no effect when optIfODUkTTIMDetMode has the value off(1).
Status: current Access: read-create
OBJECT-TYPE    
  OptIfExSAPI  

optIfODUkTTraceIdentifierAccepted 1.3.6.1.2.1.10.133.1.9.1.1.6
The actual trace identifier accepted. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The value of this object is unspecified when optIfODUkTCurrentStatus indicates a near-end defect (i.e., oci(0), lck(1), ssf(5)) that prevents extraction of the trace message.
Status: current Access: read-only
OBJECT-TYPE    
  OptIfAcTI  

optIfODUkTTIMDetMode 1.3.6.1.2.1.10.133.1.9.1.1.7
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The default value of this object is off(1).
Status: current Access: read-create
OBJECT-TYPE    
  OptIfTIMDetMode  

optIfODUkTTIMActEnabled 1.3.6.1.2.1.10.133.1.9.1.1.8
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. This object has no effect when optIfODUkTTIMDetMode has the value off(1). The default value of this object is false(2).
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

optIfODUkTDEGThr 1.3.6.1.2.1.10.133.1.9.1.1.9
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to optIfODUkTDEGThr. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The default value of this object is Severely Errored Second (SES) Estimator (See ITU-T G.7710).
Status: current Access: read-create
OBJECT-TYPE    
  OptIfDEGThr  

optIfODUkTDEGM 1.3.6.1.2.1.10.133.1.9.1.1.10
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if optIfODUkTDEGM consecutive bad PM Seconds are detected. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The default value of this object is 7 (See ITU-T G.7710).
Status: current Access: read-create
OBJECT-TYPE    
  OptIfDEGM  

optIfODUkTSinkMode 1.3.6.1.2.1.10.133.1.9.1.1.11
This variable specifies the TCM mode at the entity. The value operational(1) means that TCM Overhead (TCMOH) processes (see ITU-T G.798) shall be performed and consequent actions for AIS, Trail Signal Fail (TSF), Trail Signal Degraded (TSD) shall be initiated in case of defects. The value monitor(2) means that TCMOH processes shall be performed but consequent actions for AIS, Trail Server Failure (TSF), Trail Server Degraded (TSD) shall _not_ be initiated in case of defects. This object is applicable only when the value of optIfODUkTtpPresent is false(2) and also either one of the following three cases holds: (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER operational(1), monitor(2)  

optIfODUkTSinkLockSignalAdminState 1.3.6.1.2.1.10.133.1.9.1.1.12
Provides the capability to provision the LOCK signal, which is one of the ODUk maintenance signals, at the ODUKT sink. When a Tandem Connection endpoint is set to admin state locked, it inserts the ODUk-LCK signal in the sink direction. This object is applicable only when the value of optIfODUkTtpPresent is false(2) and also either one of the following three cases holds: (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER locked(1), normal(2)  

optIfODUkTSourceLockSignalAdminState 1.3.6.1.2.1.10.133.1.9.1.1.13
Provides the capability to provision the LOCK signal, which is one of the ODUk maintenance signals, at the source. When a Tandem Connection endpoint is set to admin state locked, it inserts the ODUk-LCK signal in the source direction. This object is applicable only when either one of the following three cases holds: (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value false(2), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value true(1). It must not be instantiated in rows for all other cases.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER locked(1), normal(2)  

optIfODUkTCurrentStatus 1.3.6.1.2.1.10.133.1.9.1.1.14
Indicates the defect condition of the entity, if any. This object is applicable only when either one of the following three cases holds: (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases.
Status: current Access: read-only
OBJECT-TYPE    
  BITS oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)  

optIfODUkTRowStatus 1.3.6.1.2.1.10.133.1.9.1.1.15
This columnar object is used for creating and deleting a conceptual row of the optIfODUkT config table. It is used to model the addTCM and removeTCM operations of an ODUk_CTP or ODUk_TTP for Tandem connection monitoring as defined in ITU-T G.874.1. Setting RowStatus to createAndGo or createAndWait implies addTCM. Setting RowStatus to destroy implies removeTCM. Successful addition/removal of TCM will result in updating the optIfODUkTcmFieldsInUse and optIfODUkPositionSeqCurrentSize variables and the optIfODUkPositionSeqTable table of the associated ODUk entry in the optIfODUkConfigTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

optIfODUkTNimConfigTable 1.3.6.1.2.1.10.133.1.9.2
A table of ODUkTNim configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OptIfODUkTNimConfigEntry

optIfODUkTNimConfigEntry 1.3.6.1.2.1.10.133.1.9.2.1
A conceptual row that contains ODUkTNim configuration information of an interface. Each instance must correspond to an instance of optIfODUkConfigEntry. Rows in this table are mutually exclusive with rows in the ODUkT config table -- in other words, this row object may not be instantiated for a given pair of ifIndex and TCM field values if a corresponding instance of optIfODUkTConfigEntry already exists. Instances of this conceptual row persist across agent restarts, and read-create columns other than the status column may be modified while the row is active.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfODUkTNimConfigEntry  

optIfODUkTNimTcmField 1.3.6.1.2.1.10.133.1.9.2.1.1
Indicates the tandem connection monitoring field of the ODUk OH on which non-intrusive monitoring is performed. Valid values are integers from 1 to 6.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..6  

optIfODUkTNimDirectionality 1.3.6.1.2.1.10.133.1.9.2.1.2
Specifies the monitor point for the ODUk TCM non-intrusive monitoring function. The value source(2) is not allowed if the corresponding instance of optIfODUkDirectionality has the value sink(1), and the value sink(1) is not allowed if the corresponding instance of optIfODUkDirectionality has the value source(2). Either the value sink(1) or source(2) is allowed if the corresponding instance of optIfODUkDirectionality has the value bidirectional(3). The value sink(1) means monitoring at the sink direction TCM signal of the ODUk CTP. The value source(2) means monitoring at the source direction path signal of the ODUk CTP.
Status: current Access: not-accessible
OBJECT-TYPE    
  OptIfSinkOrSource  

optIfODUkTNimDAPIExpected 1.3.6.1.2.1.10.133.1.9.2.1.3
The DAPI expected by the receiver. This object has no effect if optIfODUkTNimTIMDetMode has the value off(1) or sapi(3).
Status: current Access: read-create
OBJECT-TYPE    
  OptIfExDAPI  

optIfODUkTNimSAPIExpected 1.3.6.1.2.1.10.133.1.9.2.1.4
The SAPI expected by the receiver. This object has no effect if optIfODUkTNimTIMDetMode has the value off(1) or dapi(2).
Status: current Access: read-create
OBJECT-TYPE    
  OptIfExSAPI  

optIfODUkTNimTraceIdentifierAccepted 1.3.6.1.2.1.10.133.1.9.2.1.5
The actual trace identifier accepted. The value of this object is unspecified if optIfODUkTNimCurrentStatus has any of the bit positions oci(0), lck(1), or ssf(5) set or if optIfODUkTNimRowStatus has any value other than active(1).
Status: current Access: read-only
OBJECT-TYPE    
  OptIfAcTI  

optIfODUkTNimTIMDetMode 1.3.6.1.2.1.10.133.1.9.2.1.6
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function.
Status: current Access: read-create
OBJECT-TYPE    
  OptIfTIMDetMode  

optIfODUkTNimTIMActEnabled 1.3.6.1.2.1.10.133.1.9.2.1.7
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

optIfODUkTNimDEGThr 1.3.6.1.2.1.10.133.1.9.2.1.8
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to optIfODUkTNimDEGThr.
Status: current Access: read-create
OBJECT-TYPE    
  OptIfDEGThr  

optIfODUkTNimDEGM 1.3.6.1.2.1.10.133.1.9.2.1.9
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if optIfODUkTNimDEGM consecutive bad PM Seconds are detected.
Status: current Access: read-create
OBJECT-TYPE    
  OptIfDEGM  

optIfODUkTNimCurrentStatus 1.3.6.1.2.1.10.133.1.9.2.1.10
Indicates the defect condition of the entity, if any. The value of this object is unspecified if optIfODUkTNimRowStatus has any value other than active(1).
Status: current Access: read-only
OBJECT-TYPE    
  BITS oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)  

optIfODUkTNimRowStatus 1.3.6.1.2.1.10.133.1.9.2.1.11
This columnar object is used for creating and deleting a conceptual row of the optIfODUkTNim config table. It is used to model the addTCM and removeTCM operations of an ODUk_CTP or ODUk_TTP for non-intrusive Tandem connection monitoring as defined in ITU-T G.874.1. Setting RowStatus to createAndGo or createAndWait implies addTCM. Setting RowStatus to destroy implies removeTCM. Successful addition/removal of Nim TCM will result in updating the optIfODUkPositionSeqCurrentSize variable and the optIfODUkPositionSeqTable table of the associated ODUk entry in the optIfODUkConfigTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

optIfOTMnGroup 1.3.6.1.2.1.10.133.2.1.1
A collection of OTMn structure information objects.
Status: current Access: read-create
OBJECT-GROUP    

optIfPerfMonGroup 1.3.6.1.2.1.10.133.2.1.2
A collection of performance monitoring interval objects.
Status: current Access: read-create
OBJECT-GROUP    

optIfOTSnCommonGroup 1.3.6.1.2.1.10.133.2.1.3
A collection of configuration objects applicable to all OTSn interfaces.
Status: current Access: read-create
OBJECT-GROUP    

optIfOTSnSourceGroupFull 1.3.6.1.2.1.10.133.2.1.4
A collection of configuration objects applicable to full-functionality/IaDI OTSn interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOTSnAPRStatusGroup 1.3.6.1.2.1.10.133.2.1.5
A collection of objects applicable to OTSn interfaces that support Automatic Power Reduction functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOTSnAPRControlGroup 1.3.6.1.2.1.10.133.2.1.6
A collection of objects applicable to OTSn interfaces that provide Automatic Power Reduction control functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOTSnSinkGroupBasic 1.3.6.1.2.1.10.133.2.1.7
A collection of configuration objects applicable to all OTSn interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOTSnSinkGroupFull 1.3.6.1.2.1.10.133.2.1.8
A collection of configuration objects applicable to full-functionality/IaDI OTSn interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOTSnSinkPreOtnPMGroup 1.3.6.1.2.1.10.133.2.1.9
A collection of pre-OTN performance monitoring objects applicable to OTSn interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOTSnSinkPreOtnPMThresholdGroup 1.3.6.1.2.1.10.133.2.1.10
A collection of pre-OTN performance monitoring threshold objects applicable to OTSn interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOTSnSourcePreOtnPMGroup 1.3.6.1.2.1.10.133.2.1.11
A collection of pre-OTN performance monitoring objects applicable to OTSn interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOTSnSourcePreOtnPMThresholdGroup 1.3.6.1.2.1.10.133.2.1.12
A collection of pre-OTN performance monitoring threshold objects applicable to OTSn interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOMSnCommonGroup 1.3.6.1.2.1.10.133.2.1.13
A collection of configuration objects applicable to all OMSn interfaces.
Status: current Access: read-create
OBJECT-GROUP    

optIfOMSnSinkGroupBasic 1.3.6.1.2.1.10.133.2.1.14
A collection of configuration objects applicable to all OMSn interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOMSnSinkPreOtnPMGroup 1.3.6.1.2.1.10.133.2.1.15
A collection of pre-OTN performance monitoring objects applicable to OMSn interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOMSnSinkPreOtnPMThresholdGroup 1.3.6.1.2.1.10.133.2.1.16
A collection of pre-OTN performance monitoring threshold objects applicable to OMSn interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOMSnSourcePreOtnPMGroup 1.3.6.1.2.1.10.133.2.1.17
A collection of pre-OTN performance monitoring objects applicable to OMSn interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOMSnSourcePreOtnPMThresholdGroup 1.3.6.1.2.1.10.133.2.1.18
A collection of pre-OTN performance monitoring threshold objects applicable to OMSn interfaces that that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOChGroupCommonGroup 1.3.6.1.2.1.10.133.2.1.19
A collection of configuration objects applicable to all OChGroup interfaces.
Status: current Access: read-create
OBJECT-GROUP    

optIfOChGroupSinkPreOtnPMGroup 1.3.6.1.2.1.10.133.2.1.20
A collection of pre-OTN performance monitoring objects applicable to OChGroup interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOChGroupSinkPreOtnPMThresholdGroup 1.3.6.1.2.1.10.133.2.1.21
A collection of pre-OTN performance monitoring threshold objects applicable to OChGroup interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOChGroupSourcePreOtnPMGroup 1.3.6.1.2.1.10.133.2.1.22
A collection of pre-OTN performance monitoring objects applicable to OChGroup interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOChGroupSourcePreOtnPMThresholdGroup 1.3.6.1.2.1.10.133.2.1.23
A collection of pre-OTN performance monitoring threshold objects applicable to OChGroup interfaces that that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOChCommonGroup 1.3.6.1.2.1.10.133.2.1.24
A collection of configuration objects applicable to all OCh interfaces.
Status: current Access: read-create
OBJECT-GROUP    

optIfOChSinkGroupBasic 1.3.6.1.2.1.10.133.2.1.25
A collection of configuration objects applicable to all OCh interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOChSinkPreOtnPMGroup 1.3.6.1.2.1.10.133.2.1.26
A collection of pre-OTN performance monitoring objects applicable to OCh interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOChSinkPreOtnPMThresholdGroup 1.3.6.1.2.1.10.133.2.1.27
A collection of pre-OTN performance monitoring threshold objects applicable to OCh interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOChSourcePreOtnPMGroup 1.3.6.1.2.1.10.133.2.1.28
A collection of pre-OTN performance monitoring objects applicable to OCh interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOChSourcePreOtnPMThresholdGroup 1.3.6.1.2.1.10.133.2.1.29
A collection of pre-OTN performance monitoring threshold objects applicable to OCh interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOTUkCommonGroup 1.3.6.1.2.1.10.133.2.1.30
A collection of configuration objects applicable to all OTUk interfaces.
Status: current Access: read-create
OBJECT-GROUP    

optIfOTUkSourceGroup 1.3.6.1.2.1.10.133.2.1.31
A collection of configuration objects applicable to OTUk interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfOTUkSinkGroup 1.3.6.1.2.1.10.133.2.1.32
A collection of configuration objects applicable to OTUk interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfGCC0Group 1.3.6.1.2.1.10.133.2.1.33
A collection of GCC0 configuration objects.
Status: current Access: read-create
OBJECT-GROUP    

optIfODUkGroup 1.3.6.1.2.1.10.133.2.1.34
A collection of configuration objects applicable to all ODUk interfaces.
Status: current Access: read-create
OBJECT-GROUP    

optIfODUkTtpSourceGroup 1.3.6.1.2.1.10.133.2.1.35
A collection of configuration objects applicable to all interfaces that support ODUk trail termination source functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfODUkTtpSinkGroup 1.3.6.1.2.1.10.133.2.1.36
A collection of ODUk configuration objects applicable to all interfaces that support ODUk trail termination sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfODUkNimGroup 1.3.6.1.2.1.10.133.2.1.37
A collection of ODUk Nim configuration objects.
Status: current Access: read-create
OBJECT-GROUP    

optIfGCC12Group 1.3.6.1.2.1.10.133.2.1.38
A collection of GCC12 configuration objects.
Status: current Access: read-create
OBJECT-GROUP    

optIfODUkTCommonGroup 1.3.6.1.2.1.10.133.2.1.39
A collection of configuration objects applicable to all ODUkT instances.
Status: current Access: read-create
OBJECT-GROUP    

optIfODUkTSourceGroup 1.3.6.1.2.1.10.133.2.1.40
A collection of configuration objects applicable to all ODUkT instances that provide source functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfODUkTSinkGroup 1.3.6.1.2.1.10.133.2.1.41
A collection of configuration objects applicable to all ODUkT instances that provide sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfODUkTSinkGroupCtp 1.3.6.1.2.1.10.133.2.1.42
A collection of configuration objects applicable to ODUkT instances not colocated with an ODUk TTP that provide sink functions.
Status: current Access: read-create
OBJECT-GROUP    

optIfODUkTNimGroup 1.3.6.1.2.1.10.133.2.1.43
A collection of ODUkT Nim configuration objects.
Status: current Access: read-create
OBJECT-GROUP    

optIfOtnConfigCompl 1.3.6.1.2.1.10.133.2.2.1
Implementation requirements for the OTN configuration functions defined in this MIB module.
Status: current Access: read-create
MODULE-COMPLIANCE    

optIfPreOtnPMCompl 1.3.6.1.2.1.10.133.2.2.2
Implementation requirements for Pre-OTN performance monitoring functions defined in this MIB module.
Status: current Access: read-create
MODULE-COMPLIANCE