PDN-IF-EXT-CONFIG-MIB
File:
PDN-IF-EXT-CONFIG-MIB.mib (8396 bytes)
Imported modules
Imported symbols
Defined Types
PdnLinkRole |
|
Objects defined with this textual convention
are used to indicate the usage of the link.
uplink (1) : interface is used as uplink
other (2) : interface is used for something other
than uplink (e.g, subtending).
|
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
uplink(1), other(2) |
|
PdnIfMultiprotocolEncapConfigEntry |
|
SEQUENCE |
|
|
|
|
pdnIfMultiprotocolEncapConfigIPRoutedPDUs |
INTEGER |
|
|
pdnIfMultiprotocolEncapConfigBridgedPDUs |
INTEGER |
|
Defined Values
pdnIfExtEncapConfig |
1.3.6.1.4.1.1795.2.24.2.6.12.3 |
This Mib is created to facilitate
configuration of interface related objects. |
MODULE-IDENTITY |
|
|
|
pdnIfMultiprotocolEncapConfigEntry |
1.3.6.1.4.1.1795.2.24.2.6.12.3.1.1 |
There will be one of these rows for each interface that
supports RFC1483. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
PdnIfMultiprotocolEncapConfigEntry |
|
|
pdnIfMultiprotocolEncapConfigIPRoutedPDUs |
1.3.6.1.4.1.1795.2.24.2.6.12.3.1.1.1 |
In the upstream direction user can configure the IP
routed PDUs in the LLC SNAP encapsulation or VC Based
Multiplexing encapsulation (RFC1483). If neither is
configured 'none' is used. The direction is determined
by the transmit direction. Initialy this object was
developed for the endpoint use where the transmit direction
is upstream. This object could be used for CO type equipment
where the direction would be downstream. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
none(1), llcSnap(2), vcBasedMultiplexing(3) |
|
pdnIfMultiprotocolEncapConfigBridgedPDUs |
1.3.6.1.4.1.1795.2.24.2.6.12.3.1.1.2 |
In the transmit direction user can configure the IP
routed PDUs in the LLC SNAP encapsulation or VC Based
Multiplexing encapsulation (RFC1483). If neither is
configured 'none' is used. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
none(1), llcSnap(2), vcBasedMultiplexing(3) |
|
pdnIfXLinkConfigTable |
1.3.6.1.4.1.1795.2.24.2.6.12.1.3 |
This table contains configuration information
for interfaces that are capable of switch roles
at run-time.
|
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
PdnIfXLinkConfigEntry |
|
pdnIfXLinkConfigEntry |
1.3.6.1.4.1.1795.2.24.2.6.12.1.3.1 |
An entry in this table represents an interface
that is capable of being used as an uplink.
Typically, this table will contain entries only
for interfaces that are capable of switching roles.
|
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
PdnIfXLinkConfigEntry |
|
|
pdnIfXLinkConfigRole |
1.3.6.1.4.1.1795.2.24.2.6.12.1.3.1.1 |
This object allows users to configure the role
(e.g., uplink) intended for this interface.
|
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
PdnLinkRole |
|
|
pdnIfMultiprotocolEncapCompliance |
1.3.6.1.4.1.1795.2.24.2.6.12.3.2.2.1 |
The compliance statement for SNMP entities which support
RFC1483 Multiprotocol Encapsulation over ATM adaptation layer 5. |
Status: current |
Access: read-only |
MODULE-COMPLIANCE |
|
|
|
pdnIfMultiprotocolEncapsulationOptionalGroup |
1.3.6.1.4.1.1795.2.24.2.6.12.3.2.1.1 |
A collection of objects providing optional configuration information
about multiprotocol interface link. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|
pdnIfXLinkConfigOptionalGroup |
1.3.6.1.4.1.1795.2.24.2.6.12.4.1.1 |
configuration information for this optional group. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|