PRIV-LSL-MIB

File: PRIV-LSL-MIB.mib (6521 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
IF-MIB PRVT-SWITCH-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE MODULE-COMPLIANCE
OBJECT-GROUP TEXTUAL-CONVENTION MacAddress
ifIndex switch

Defined Types

PrivLslStates  
The the switch on/off states for LSL on ports.
TEXTUAL-CONVENTION    
  INTEGER enable(1), disable(2)  

PrivLslManagementEntry  
SEQUENCE    
  privLslStatus PrivLslStates

PrivIometrixManagementEntry  
SEQUENCE    
  privIometrixStatus PrivLslStates

Defined Values

privLsl 1.3.6.1.4.1.738.1.5.113
MIB module for management of Logical Service Loopback(LSL) Iometrix compatible product.
MODULE-IDENTITY    

privLslLevel1 1.3.6.1.4.1.738.1.5.113.1
OBJECT IDENTIFIER    

privLslObjects 1.3.6.1.4.1.738.1.5.113.1.1
OBJECT IDENTIFIER    

privLslNotifications 1.3.6.1.4.1.738.1.5.113.1.2
OBJECT IDENTIFIER    

privLslConformance 1.3.6.1.4.1.738.1.5.113.1.3
OBJECT IDENTIFIER    

privLslGlobalMacAddress 1.3.6.1.4.1.738.1.5.113.1.1.1
This object defines the destination mac address assigned to lsl packets. The device can recognise the lsl packets by a specific destination mac address given by this object.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

privLslManagementTable 1.3.6.1.4.1.738.1.5.113.1.1.2
LSL interface extention table. This table contains all objects which are used for LSL management per interface. It uses ifIndex defined in rfc1213
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrivLslManagementEntry

privLslManagementEntry 1.3.6.1.4.1.738.1.5.113.1.1.2.1
The only valid LSL interfaces are phyical port interfaces
Status: current Access: not-accessible
OBJECT-TYPE    
  PrivLslManagementEntry  

privLslStatus 1.3.6.1.4.1.738.1.5.113.1.1.2.1.1
This object indicates whether the port have Logical Service Loopback enabled or disabled. It allows the client to determine which interface should be used for this type of service
Status: current Access: read-write
OBJECT-TYPE    
  PrivLslStates  

privIometrixManagementTable 1.3.6.1.4.1.738.1.5.113.1.1.3
Iometrix Level 1 table. This table contains all objects which are used for Iometrix level 1 management per interface. It uses ifIndex defined in rfc1213
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrivIometrixManagementEntry

privIometrixManagementEntry 1.3.6.1.4.1.738.1.5.113.1.1.3.1
the index is ifindex
Status: current Access: not-accessible
OBJECT-TYPE    
  PrivIometrixManagementEntry  

privIometrixStatus 1.3.6.1.4.1.738.1.5.113.1.1.3.1.1
This object indicates whether the port have Logical Service Loopback enabled or disabled. It allows the client to determine which interface should be used for this type of service
Status: current Access: read-write
OBJECT-TYPE    
  PrivLslStates  

privLslGroups 1.3.6.1.4.1.738.1.5.113.1.3.1
OBJECT IDENTIFIER    

privLslCompliances 1.3.6.1.4.1.738.1.5.113.1.3.2
OBJECT IDENTIFIER    

privLevel1ObjectsGroup 1.3.6.1.4.1.738.1.5.113.1.3.1.1
All objects related to level1 logical loopback service. Object grouping will be extended if the mib is also extended
Status: current Access: read-write
OBJECT-GROUP    

privLevel1Compliance 1.3.6.1.4.1.738.1.5.113.1.3.2.1
The compliance statement. It will be extended if new functionality is added
Status: current Access: read-only
MODULE-COMPLIANCE