PW-STD-MIB

File: PW-STD-MIB.mib (87696 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
SNMP-FRAMEWORK-MIB IF-MIB INET-ADDRESS-MIB
PerfHist-TC-MIB HC-PerfHist-TC-MIB PW-TC-STD-MIB
IANA-PWE3-MIB

Imported symbols

NOTIFICATION-TYPE MODULE-IDENTITY OBJECT-TYPE
Integer32 Unsigned32 Counter32
Counter64 TimeTicks transmission
MODULE-COMPLIANCE OBJECT-GROUP NOTIFICATION-GROUP
TruthValue RowStatus StorageType
TimeStamp SnmpAdminString InterfaceIndexOrZero
InetAddressType InetAddress PerfCurrentCount
PerfIntervalCount HCPerfCurrentCount HCPerfIntervalCount
HCPerfTimeElapsed HCPerfValidIntervals PwIndexType
PwIndexOrZeroType PwGroupID PwIDType
PwOperStatusTC PwAttachmentIdentifierType PwCwStatusTC
PwStatus PwFragSize PwFragStatus
PwGenIdType IANAPwTypeTC IANAPwPsnTypeTC
IANAPwCapabilities

Defined Types

PwEntry  
SEQUENCE    
  pwIndex PwIndexType
  pwType IANAPwTypeTC
  pwOwner INTEGER
  pwPsnType IANAPwPsnTypeTC
  pwSetUpPriority Integer32
  pwHoldingPriority Integer32
  pwPeerAddrType InetAddressType
  pwPeerAddr InetAddress
  pwAttachedPwIndex PwIndexOrZeroType
  pwIfIndex InterfaceIndexOrZero
  pwID PwIDType
  pwLocalGroupID PwGroupID
  pwGroupAttachmentID PwAttachmentIdentifierType
  pwLocalAttachmentID PwAttachmentIdentifierType
  pwRemoteAttachmentID PwAttachmentIdentifierType
  pwCwPreference TruthValue
  pwLocalIfMtu Unsigned32
  pwLocalIfString TruthValue
  pwLocalCapabAdvert IANAPwCapabilities
  pwRemoteGroupID PwGroupID
  pwCwStatus PwCwStatusTC
  pwRemoteIfMtu Unsigned32
  pwRemoteIfString SnmpAdminString
  pwRemoteCapabilities IANAPwCapabilities
  pwFragmentCfgSize PwFragSize
  pwRmtFragCapability PwFragStatus
  pwFcsRetentionCfg INTEGER
  pwFcsRetentionStatus BITS
  pwOutboundLabel Unsigned32
  pwInboundLabel Unsigned32
  pwName SnmpAdminString
  pwDescr SnmpAdminString
  pwCreateTime TimeStamp
  pwUpTime TimeTicks
  pwLastChange TimeTicks
  pwAdminStatus INTEGER
  pwOperStatus PwOperStatusTC
  pwLocalStatus PwStatus
  pwRemoteStatusCapable INTEGER
  pwRemoteStatus PwStatus
  pwTimeElapsed HCPerfTimeElapsed
  pwValidIntervals HCPerfValidIntervals
  pwRowStatus RowStatus
  pwStorageType StorageType
  pwOamEnable TruthValue
  pwGenAGIType PwGenIdType
  pwGenLocalAIIType PwGenIdType
  pwGenRemoteAIIType PwGenIdType

PwPerfCurrentEntry  
SEQUENCE    
  pwPerfCurrentInHCPackets HCPerfCurrentCount
  pwPerfCurrentInHCBytes HCPerfCurrentCount
  pwPerfCurrentOutHCPackets HCPerfCurrentCount
  pwPerfCurrentOutHCBytes HCPerfCurrentCount
  pwPerfCurrentInPackets PerfCurrentCount
  pwPerfCurrentInBytes PerfCurrentCount
  pwPerfCurrentOutPackets PerfCurrentCount
  pwPerfCurrentOutBytes PerfCurrentCount

PwPerfIntervalEntry  
SEQUENCE    
  pwPerfIntervalNumber Integer32
  pwPerfIntervalValidData TruthValue
  pwPerfIntervalTimeElapsed HCPerfTimeElapsed
  pwPerfIntervalInHCPackets HCPerfIntervalCount
  pwPerfIntervalInHCBytes HCPerfIntervalCount
  pwPerfIntervalOutHCPackets HCPerfIntervalCount
  pwPerfIntervalOutHCBytes HCPerfIntervalCount
  pwPerfIntervalInPackets PerfIntervalCount
  pwPerfIntervalInBytes PerfIntervalCount
  pwPerfIntervalOutPackets PerfIntervalCount
  pwPerfIntervalOutBytes PerfIntervalCount

PwPerf1DayIntervalEntry  
SEQUENCE    
  pwPerf1DayIntervalNumber Unsigned32
  pwPerf1DayIntervalValidData TruthValue
  pwPerf1DayIntervalTimeElapsed HCPerfTimeElapsed
  pwPerf1DayIntervalInHCPackets Counter64
  pwPerf1DayIntervalInHCBytes Counter64
  pwPerf1DayIntervalOutHCPackets Counter64
  pwPerf1DayIntervalOutHCBytes Counter64

PwIndexMappingEntry  
SEQUENCE    
  pwIndexMappingPwType IANAPwTypeTC
  pwIndexMappingPwID PwIDType
  pwIndexMappingPeerAddrType InetAddressType
  pwIndexMappingPeerAddr InetAddress
  pwIndexMappingPwIndex PwIndexType

PwPeerMappingEntry  
SEQUENCE    
  pwPeerMappingPeerAddrType InetAddressType
  pwPeerMappingPeerAddr InetAddress
  pwPeerMappingPwType IANAPwTypeTC
  pwPeerMappingPwID PwIDType
  pwPeerMappingPwIndex PwIndexType

PwGenFecIndexMappingEntry  
SEQUENCE    
  pwGenFecIndexMappingAGIType PwGenIdType
  pwGenFecIndexMappingAGI PwAttachmentIdentifierType
  pwGenFecIndexMappingLocalAIIType PwGenIdType
  pwGenFecIndexMappingLocalAII PwAttachmentIdentifierType
  pwGenFecIndexMappingRemoteAIIType PwGenIdType
  pwGenFecIndexMappingRemoteAII PwAttachmentIdentifierType
  pwGenFecIndexMappingPwIndex PwIndexType

Defined Values

pwStdMIB 1.3.6.1.2.1.10.246
This MIB module contains managed object definitions for pseudowire operation as in Bryant, S. and P. Pate, 'Pseudo Wire Emulation Edge-to-Edge (PWE3) Architecture' [RFC3985], Martini, L., et al, 'Pseudowire Setup and Maintenance Using the Label Distribution Protocol (LDP)' [RFC4447], and Townsley, M., et al, 'Layer Two Tunneling Protocol (Version 3)' [RFC3931]. This MIB module enables the use of any underlying packet switched network (PSN). MIB nodules that will support PW operations over specific PSN types are defined in separate memos. The indexes for this MIB module are also used to index the PSN-specific tables and the PW-specific tables. The PW Type dictates which PW-specific MIB module to use. Copyright (c) 2009 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. - Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. - Neither the name of Internet Society, IETF or IETF Trust, nor the names of specific contributors, may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This version of this MIB module is part of RFC 5601; see the RFC itself for full legal notices.
MODULE-IDENTITY    

pwNotifications 1.3.6.1.2.1.10.246.0
OBJECT IDENTIFIER    

pwObjects 1.3.6.1.2.1.10.246.1
OBJECT IDENTIFIER    

pwConformance 1.3.6.1.2.1.10.246.2
OBJECT IDENTIFIER    

pwIndexNext 1.3.6.1.2.1.10.246.1.1
This object contains an appropriate value to be used for pwIndex when creating entries in the pwTable. The value 0 indicates that no unassigned entries are available. To obtain the value of pwIndex for a new entry in the pwTable, the manager issues a management protocol retrieval operation. The agent will determine through its local policy when this index value will be made available for reuse.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

pwTable 1.3.6.1.2.1.10.246.1.2
This table specifies information for configuring and status monitoring that is common to all service types and PSN types.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwEntry

pwEntry 1.3.6.1.2.1.10.246.1.2.1
A row in this table represents a pseudowire (PW) virtual connection across a packet network. It is indexed by pwIndex, which uniquely identifies a singular connection. A row can be created by an operator command from a management plan of a PE, by signaling, or due to auto- discovery process. An operator's command can be issued via a non-SNMP application; in such case, a row will be created implicitly by the agent. The read-create objects in this table are divided into three categories: 1) Objects that MUST NOT be changed after row activation. These are objects that define basic properties of the PW (for example type, destination, etc.). 2) Objects that MAY be changed when the PW is defined as not active. A change of these objects involves re-signaling of the PW or it might be traffic affecting. PW not active is defined as one of the following conditions: a) The pwRowStatus is notInService(2). b) The pwRowStatus is notReady(3). c) The pwAdminStatus is down(2). If the operator needs to change one of the values for an active row, the operator can either set the pwRowStatus to notInService(2) or set pwAdminStatus to down(2). Signaling (or traffic) is initiated again upon setting the pwRowStatus to active(1) or setting the pwAdminStatus to up(1) or testing(3), respectively. 3) Objects that MAY be changed at any time. A PW MAY have an entry in the ifTable in addition to the entry in this table. In this case, a special ifType for PW will be set in the ifTable, and the ifIndex in the ifTable of the PW will be set in the pwIfIndex object in this table. By default, all the read-create objects MUST NOT be changed after row activation, unless specifically indicated in the individual object description. Manual entries in this table SHOULD be preserved after a reboot; the agent MUST ensure the integrity of those entries. If the set of entries of a specific row are found to be inconsistent after reboot, the PW pwOperStatus MUST be declared as notPresent(5).
Status: current Access: not-accessible
OBJECT-TYPE    
  PwEntry  

pwIndex 1.3.6.1.2.1.10.246.1.2.1.1
A unique index for the conceptual row identifying a PW within this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwIndexType  

pwType 1.3.6.1.2.1.10.246.1.2.1.2
This value indicates the emulated service to be carried over this PW.
Status: current Access: read-create
OBJECT-TYPE    
  IANAPwTypeTC  

pwOwner 1.3.6.1.2.1.10.246.1.2.1.3
This object is set by the operator to indicate the protocol responsible for establishing this PW. 'manual' is used in all cases where no maintenance protocol (PW signaling) is used to set up the PW, i.e., configuration of entries in the PW tables including PW labels, etc., is done by setting the MIB fields manually. 'pwIdFecSignaling' is used in case of signaling with the Pwid FEC element with LDP signaling. 'genFecSignaling' is used in case of LDP signaling with the generalized FEC. 'l2tpControlProtocol' indicates the use of the L2TP control protocol. 'other' is used for other types of signaling.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER manual(1), pwIdFecSignaling(2), genFecSignaling(3), l2tpControlProtocol(4), other(5)  

pwPsnType 1.3.6.1.2.1.10.246.1.2.1.4
This object is set by the operator to indicate the PSN type. Based on this object, the relevant PSN table's entry is created in the PSN-specific MIB modules.
Status: current Access: read-create
OBJECT-TYPE    
  IANAPwPsnTypeTC  

pwSetUpPriority 1.3.6.1.2.1.10.246.1.2.1.5
This object defines the relative priority of the PW during set-up in a lowest-to-highest fashion, where 0 is the highest priority. PWs with the same priority are treated with equal priority. PWs that have not yet completed setup will report 'dormant' in the pwOperStatus. This value is significant if there are competing resources among PWs and the implementation supports this feature. Equal priority handling with competing resources is implementation specific. This object MAY be changed at any time.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

pwHoldingPriority 1.3.6.1.2.1.10.246.1.2.1.6
This object defines the relative holding priority of the PW in a lowest-to-highest fashion, where 0 is the highest priority. PWs with the same priority are treated equally. This value is significant if there are competing resources among PWs and the implementation supports this feature. Equal priority handling with competing resources is implementation specific. This object MAY be changed only if the PW is not active.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

pwPeerAddrType 1.3.6.1.2.1.10.246.1.2.1.8
Denotes the address type of the peer node. It should be set to 'unknown' if PE/PW maintenance protocol is not used and the address is unknown.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

pwPeerAddr 1.3.6.1.2.1.10.246.1.2.1.9
This object contains the value of the peer node address of the PW/PE maintenance protocol entity. This object SHOULD contain a value of all zeroes if not applicable (pwPeerAddrType is 'unknown').
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

pwAttachedPwIndex 1.3.6.1.2.1.10.246.1.2.1.10
If the PW is attached to another PW instead of a local native service, this item indicates the pwIndex of the attached PW. Otherwise, this object MUST be set to zero. Attachment to another PW will have no PW specific entry in any of the service MIB modules.
Status: current Access: read-create
OBJECT-TYPE    
  PwIndexOrZeroType  

pwIfIndex 1.3.6.1.2.1.10.246.1.2.1.11
This object indicates the ifIndex of the PW if the PW is represented in the ifTable. Otherwise, it MUST be set to zero.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

pwID 1.3.6.1.2.1.10.246.1.2.1.12
Pseudowire identifier. If the pwOwner object is 'pwIdFecSignaling' or 'l2tpControlProtocol', then this object is signaled in the outgoing PW ID field within the 'Virtual Circuit FEC Element'. For other values of pwOwner, this object is not signaled and it MAY be set to zero. For implementations that support the pwIndexMappingTable, a non-zero value is RECOMMENDED, even if this identifier is not signaled. This is so that reverse mappings can be provided by pwIndexMappingTable and pwPeerMappingTable. It is therefore RECOMMENDED that the value of this pwID be unique (or if pwPeerAddrType is not 'unknown', at least [pwType, pwID, pwPeerAddrType, pwPeerAddr] is unique.)
Status: current Access: read-create
OBJECT-TYPE    
  PwIDType  

pwLocalGroupID 1.3.6.1.2.1.10.246.1.2.1.13
Used in the Group ID field sent to the peer PW End Service within the maintenance protocol used for PW setup. It SHOULD be set to zero if a maintenance protocol is not used.
Status: current Access: read-create
OBJECT-TYPE    
  PwGroupID  

pwGroupAttachmentID 1.3.6.1.2.1.10.246.1.2.1.14
This object is an octet string representing the attachment group identifier (AGI) that this PW belongs to, which typically identifies the VPN ID. Applicable if pwOwner equals 'genFecSignaling'.
Status: current Access: read-create
OBJECT-TYPE    
  PwAttachmentIdentifierType  

pwLocalAttachmentID 1.3.6.1.2.1.10.246.1.2.1.15
This object is an octet string representing the local forwarder attachment individual identifier (AII) to be used by this PW. It is used as the Source AII (SAII) for outgoing signaling messages and the Target AII (TAII) in the incoming messages from the peer. Applicable if pwOwner equal 'genFecSignaling'.
Status: current Access: read-create
OBJECT-TYPE    
  PwAttachmentIdentifierType  

pwRemoteAttachmentID 1.3.6.1.2.1.10.246.1.2.1.16
This object is an octet string representing the remote forwarder attachment individual identifier (AII) to be used by this PW. It is used as the TAII for outgoing signaling messages and the SAII in the incoming messages from the peer. Applicable if pwOwner equals 'genFecSignaling'.
Status: current Access: read-create
OBJECT-TYPE    
  PwAttachmentIdentifierType  

pwCwPreference 1.3.6.1.2.1.10.246.1.2.1.17
Defines if the control word will be sent with each packet by the local node. Some PW types mandate the use of a control word, and in such cases, the value configured for this object has no effect on the existence of the control word. This object MAY be changed only if the PW is not active.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwLocalIfMtu 1.3.6.1.2.1.10.246.1.2.1.18
If not equal to zero, the optional IfMtu object in the signaling protocol will be sent with this value, which represents the locally supported MTU size over the interface (or the virtual interface) associated with the PW. This object MAY be changed only if the PW is not active.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

pwLocalIfString 1.3.6.1.2.1.10.246.1.2.1.19
A PW MAY be associated to an interface (or a virtual interface) in the ifTable of the node as part of the service configuration. This object defines if the maintenance protocol will send the interface's name (ifAlias) as it appears in the ifTable. If set to false, the optional element will not be sent. This object MAY be changed only if the PW is not active.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwLocalCapabAdvert 1.3.6.1.2.1.10.246.1.2.1.20
If a maintenance protocol is used, it indicates the capabilities the local node will advertise to the peer. The operator MAY selectively assign a partial set of capabilities. In case of manual configuration of the PW, the operator SHOULD set non-conflicting options (for example, only a single type of Operations, Administration, and Management (OAM)) out of the available options in the implementation. It is possible to change the value of this object when the PW is not active. The agent MUST reject any attempt to set a capability that is not supported. The default value MUST be the full set of local node capabilities.
Status: current Access: read-create
OBJECT-TYPE    
  IANAPwCapabilities  

pwRemoteGroupID 1.3.6.1.2.1.10.246.1.2.1.21
This object is obtained from the Group ID field as received via the maintenance protocol used for PW setup. Value of zero will be reported if not used. Value of 0xFFFFFFFF shall be used if the object is yet to be defined by the PW maintenance protocol.
Status: current Access: read-only
OBJECT-TYPE    
  PwGroupID  

pwCwStatus 1.3.6.1.2.1.10.246.1.2.1.22
If signaling is used for PW establishment, this object indicates the status of the control word negotiation. For either signaling or manual configuration, it indicates if the control word (CW) is to be present for this PW.
Status: current Access: read-only
OBJECT-TYPE    
  PwCwStatusTC  

pwRemoteIfMtu 1.3.6.1.2.1.10.246.1.2.1.23
The remote interface MTU as (optionally) received from the remote node via the maintenance protocol. The object SHOULD report zero if the MTU is not available.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

pwRemoteIfString 1.3.6.1.2.1.10.246.1.2.1.24
Indicates the interface description string as received by the maintenance protocol. It MUST be a NULL string if a maintenance protocol is not used or the value is not known yet.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..80)  

pwRemoteCapabilities 1.3.6.1.2.1.10.246.1.2.1.25
Indicates the capabilities as received from the peer.
Status: current Access: read-only
OBJECT-TYPE    
  IANAPwCapabilities  

pwFragmentCfgSize 1.3.6.1.2.1.10.246.1.2.1.26
If set to a value other than zero, indicates that fragmentation is desired for this PW. This object MAY be changed only if the PW is not active.
Status: current Access: read-create
OBJECT-TYPE    
  PwFragSize  

pwRmtFragCapability 1.3.6.1.2.1.10.246.1.2.1.27
The status of the fragmentation based on the local configuration and the peer capabilities as received from the peer when a control protocol is used.
Status: current Access: read-only
OBJECT-TYPE    
  PwFragStatus  

pwFcsRetentionCfg 1.3.6.1.2.1.10.246.1.2.1.28
The local configuration of Frame Check Sequence (FCS) retention for this PW. FCS retention can be configured for PW types High-Level Data Link Control (HDLC), Point-to-Point Protocol (PPP), and Ethernet only. If the implementation does not support FCS retention, an error MUST be reported in pwFcsRetentionStatus. This object MAY be changed only if the PW is not active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER fcsRetentionDisable(1), fcsRetentionEnable(2)  

pwFcsRetentionStatus 1.3.6.1.2.1.10.246.1.2.1.29
The status of the FCS retention negotiation process based on local configuration and the remote advertisement. remoteIndicationUnknown - set if a FEC has not been received from the remote. remoteRequestFcsRetention - indicates that the peer has requested FCS retention. FCS retention will be used if the local node is capable and configured to use it for this PW. fcsRetentionEnabled - FCS retention is enabled (both peers were configured for FCS retention for signaled PW, or the local node is configured and capable of FCS retention for manually assigned PWs). fcsRetentionDisabled - FCS retention is disabled (not configured locally or not advertised by the peer). localFcsRetentionCfgErr - set if the local node has been configured for FCS retention but is not capable to support it. fcsRetentionFcsSizeMismatch - set if there is an FCS size mismatch between the local and the peer node.
Status: current Access: read-only
OBJECT-TYPE    
  BITS remoteIndicationUnknown(0), remoteRequestFcsRetention(1), fcsRetentionEnabled(2), fcsRetentionDisabled(3), localFcsRetentionCfgErr(4), fcsRetentionFcsSizeMismatch(5)  

pwOutboundLabel 1.3.6.1.2.1.10.246.1.2.1.30
The PW label used in the outbound direction (i.e., toward the PSN). It might be set manually if pwOwner is 'manual'; otherwise, it is set automatically. For MPLS, MPLS over IP, or MPLS over Generic Routing Encapsulation (GRE) PSN, it represents the 20-bit PW tag; for L2TP, it represents the 32-bit Session ID; and for IP PSN, it represents the destination UDP port number. If the label is not yet known (signaling in process), the object SHOULD return a value of 0xFFFFFFFF. For manual configuration, this object MAY be changed only if the PW is not active.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

pwInboundLabel 1.3.6.1.2.1.10.246.1.2.1.31
The PW label used in the inbound direction (i.e., packets received from the PSN). It may be set manually if pwOwner is 'manual'; otherwise, it is set automatically. For MPLS, MPLS over IP, or MPLS over GRE PSN, it represents the 20-bit PW tag; for L2TP, it represents the 32-bit Session ID; and for IP PSN, it represents the source UDP port number. If the label is not yet known (signaling in process), the object SHOULD return a value of 0xFFFFFFFF. For manual configuration, this object MAY be changed only if the PW is not active.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

pwName 1.3.6.1.2.1.10.246.1.2.1.32
The canonical name assigned to the PW. This object MAY be changed at any time.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

pwDescr 1.3.6.1.2.1.10.246.1.2.1.33
A textual string containing information about the PW. If there is no description, this object contains a zero- length string. This object MAY be changed at any time.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

pwCreateTime 1.3.6.1.2.1.10.246.1.2.1.34
The value of sysUpTime at the time this PW was created.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

pwUpTime 1.3.6.1.2.1.10.246.1.2.1.35
Specifies the time since last change of pwOperStatus to Up(1).
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

pwLastChange 1.3.6.1.2.1.10.246.1.2.1.36
The value of sysUpTime at the time the PW entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

pwAdminStatus 1.3.6.1.2.1.10.246.1.2.1.37
The desired operational status of this PW. This object MAY be set at any time.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

pwOperStatus 1.3.6.1.2.1.10.246.1.2.1.38
This object indicates the operational status of the PW; it does not reflect the status of the Customer Edge (CE) bound interface. It is set to down only if pwNotForwarding, psnFacingPwRxFault, or psnFacingPwTxFault indications are set in pwLocalStatus or pwRemoteStatus. It indicates 'lowerLayerDown' if the only reason for not being in the 'up' state is that either the outer tunnel or physical layer of the network side is in the 'down' state. All other states are declared based on the description of the PwOperStatusTC.
Status: current Access: read-only
OBJECT-TYPE    
  PwOperStatusTC  

pwLocalStatus 1.3.6.1.2.1.10.246.1.2.1.39
Indicates the status of the PW in the local node. The various indications in this object SHOULD be available independent of the ability of the local node to advertise them or the remote node to accept these status indications through the control protocol.
Status: current Access: read-only
OBJECT-TYPE    
  PwStatus  

pwRemoteStatusCapable 1.3.6.1.2.1.10.246.1.2.1.40
Indicates the remote node capability to advertise the PW status notification. notApplicable SHOULD be reported for a manually set PW, or if the local node is not capable of accepting the status notification object. notYetKnown SHOULD be reported if the signaling protocol has not yet finished the process of capability determination. remoteCapable and remoteNotcapable SHOULD be reported based on the initial signaling exchange that has determined the remote node capability.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(1), notYetKnown(2), remoteCapable(3), remoteNotCapable(4)  

pwRemoteStatus 1.3.6.1.2.1.10.246.1.2.1.41
Indicates the status of the PW as was advertised by the remote. If the remote is not capable of advertising the status object, or the local node is not able to accept the status object through signaling, then the applicable bit is 'pwNotForwarding', which is set if the remote has sent label release or label withdraw for this PW.
Status: current Access: read-only
OBJECT-TYPE    
  PwStatus  

pwTimeElapsed 1.3.6.1.2.1.10.246.1.2.1.42
The number of seconds, including partial seconds, that have elapsed since the beginning of the current interval measurement period.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfTimeElapsed  

pwValidIntervals 1.3.6.1.2.1.10.246.1.2.1.43
The number of previous 15-minute intervals for which data was collected.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfValidIntervals  

pwRowStatus 1.3.6.1.2.1.10.246.1.2.1.44
For creating, modifying, and deleting this row. This object MAY be changed at any time.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pwStorageType 1.3.6.1.2.1.10.246.1.2.1.45
This variable indicates the storage type for this object.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

pwOamEnable 1.3.6.1.2.1.10.246.1.2.1.46
This variable indicates if OAM is enabled for this PW. It MAY be changed at any time.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwGenAGIType 1.3.6.1.2.1.10.246.1.2.1.47
This variable indicates the AGI type if generalized FEC (129) is used for PW signaling or configuration. It SHOULD return the value of zero otherwise.
Status: current Access: read-create
OBJECT-TYPE    
  PwGenIdType  

pwGenLocalAIIType 1.3.6.1.2.1.10.246.1.2.1.48
This object is the type of the local forwarder attachment individual identifier (AII) to be used by this PW if generalized FEC (129) is used for PW signaling or configuration.
Status: current Access: read-create
OBJECT-TYPE    
  PwGenIdType  

pwGenRemoteAIIType 1.3.6.1.2.1.10.246.1.2.1.49
This object is the type of the remote forwarder attachment individual identifier (AII) to be used by this PW if generalized FEC (129) is used for PW signaling or configuration.
Status: current Access: read-create
OBJECT-TYPE    
  PwGenIdType  

pwPerfCurrentTable 1.3.6.1.2.1.10.246.1.3
This table provides per-PW performance information for the current interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwPerfCurrentEntry

pwPerfCurrentEntry 1.3.6.1.2.1.10.246.1.3.1
An entry in this table is created by the agent for every PW.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwPerfCurrentEntry  

pwPerfCurrentInHCPackets 1.3.6.1.2.1.10.246.1.3.1.1
High-capacity counter for number of packets received by the PW (from the PSN) in the current 15-minute interval. This is the 64-bit version of pwPerfCurrentInPackets, if pwPerfCurrentInHCPackets is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfCurrentCount  

pwPerfCurrentInHCBytes 1.3.6.1.2.1.10.246.1.3.1.2
High-capacity counter for number of bytes received by the PW (from the PSN) in the current 15-minute interval. This is the 64-bit version of pwPerfCurrentInBytes, if pwPerfCurrentInHCBytes is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfCurrentCount  

pwPerfCurrentOutHCPackets 1.3.6.1.2.1.10.246.1.3.1.3
High-capacity counter for number of packets forwarded by the PW (to the PSN) in the current 15-minute interval. This is the 64-bit version of pwPerfCurrentOutPackets, if pwPerfCurrentOutHCPackets is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfCurrentCount  

pwPerfCurrentOutHCBytes 1.3.6.1.2.1.10.246.1.3.1.4
High-capacity counter for number of bytes forwarded by the PW (to the PSN) in the current 15-minute interval. This is the 64-bit version of pwPerfCurrentOutBytes, if pwPerfCurrentOutHCBytes is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfCurrentCount  

pwPerfCurrentInPackets 1.3.6.1.2.1.10.246.1.3.1.5
The counter for number of packets received by the PW (from the PSN) in the current 15-minute interval. This is the 32-bit version of pwPerfCurrentInHCPackets, if pwPerfCurrentInHCPackets is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

pwPerfCurrentInBytes 1.3.6.1.2.1.10.246.1.3.1.6
The counter for number of bytes received by the PW (from the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwPerfCurrentInHCBytes, if pwPerfCurrentInHCBytes is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

pwPerfCurrentOutPackets 1.3.6.1.2.1.10.246.1.3.1.7
The counter for number of packets forwarded by the PW (to the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwPerfCurrentOutHCPackets, if pwPerfCurrentOutHCPackets is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

pwPerfCurrentOutBytes 1.3.6.1.2.1.10.246.1.3.1.8
The counter for number of bytes forwarded by the PW (to the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwPerfCurrentOutHCBytes, if pwPerfCurrentOutHCBytes is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

pwPerfIntervalTable 1.3.6.1.2.1.10.246.1.4
This table provides per-PW performance information for each interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwPerfIntervalEntry

pwPerfIntervalEntry 1.3.6.1.2.1.10.246.1.4.1
An entry in this table is created by the agent for every PW.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwPerfIntervalEntry  

pwPerfIntervalNumber 1.3.6.1.2.1.10.246.1.4.1.1
A number N, between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15-minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. The minimum range of N is 1 through 4. The default range is 1 to 32. The maximum range of N is 1 through 96.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..96  

pwPerfIntervalValidData 1.3.6.1.2.1.10.246.1.4.1.2
This variable indicates if the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pwPerfIntervalTimeElapsed 1.3.6.1.2.1.10.246.1.4.1.3
The duration of this interval in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfTimeElapsed  

pwPerfIntervalInHCPackets 1.3.6.1.2.1.10.246.1.4.1.4
High-capacity counter for number of packets received by the PW (from the PSN) during the interval. This is the 64-bit version of pwPerfIntervalInPackets, if pwPerfIntervalInHCPackets is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfIntervalCount  

pwPerfIntervalInHCBytes 1.3.6.1.2.1.10.246.1.4.1.5
High-capacity counter for number of bytes received by the PW (from the PSN) during the interval. This is the 64-bit version of pwPerfIntervalInBytes, if pwPerfIntervalInHCBytes is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfIntervalCount  

pwPerfIntervalOutHCPackets 1.3.6.1.2.1.10.246.1.4.1.6
High-capacity counter for number of packets forwarded by the PW (to the PSN) during the interval. This is the 64-bit version of pwPerfIntervalOutPackets, if pwPerfIntervalOutHCPackets is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfIntervalCount  

pwPerfIntervalOutHCBytes 1.3.6.1.2.1.10.246.1.4.1.7
High-capacity counter for number of bytes forwarded by the PW (to the PSN) during the interval. This is the 64-bit version of pwPerfIntervalOutBytes, if pwPerfIntervalOutHCBytes is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfIntervalCount  

pwPerfIntervalInPackets 1.3.6.1.2.1.10.246.1.4.1.8
This value represents the number of packets received by this PW during the interval. It MUST be equal to the least significant 32 bits of pwPerfIntervalInHCPackets, if pwPerfIntervalInHCPackets is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

pwPerfIntervalInBytes 1.3.6.1.2.1.10.246.1.4.1.9
This value represents the number of bytes received by this PW during the interval. It MUST be equal to the least significant 32 bits of pwPerfIntervalInHCBytes, if pwPerfIntervalInHCBytes is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

pwPerfIntervalOutPackets 1.3.6.1.2.1.10.246.1.4.1.10
This value represents the number of packets sent by this PW during the interval. It MUST be equal to the least significant 32 bits of pwPerfIntervalOutHCPackets, if pwPerfIntervalOutHCPackets is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

pwPerfIntervalOutBytes 1.3.6.1.2.1.10.246.1.4.1.11
This value represents the number of bytes sent by this PW during the interval. It MUST be equal to the least significant 32 bits of pwPerfIntervalOutHCBytes, if pwPerfIntervalOutHCBytes is supported according to the rules spelled out in RFC 2863.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

pwPerf1DayIntervalTable 1.3.6.1.2.1.10.246.1.5
This table provides per-PW performance information for the current day's measurement and the previous day's interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwPerf1DayIntervalEntry

pwPerf1DayIntervalEntry 1.3.6.1.2.1.10.246.1.5.1
An entry in this table is created by the agent for every PW.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwPerf1DayIntervalEntry  

pwPerf1DayIntervalNumber 1.3.6.1.2.1.10.246.1.5.1.1
History Data Interval number. Interval 1 is the current day's measurement period, interval 2 is the most recent previous day, and interval 30 is 31 days ago. Intervals 3..31 are optional.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..31  

pwPerf1DayIntervalValidData 1.3.6.1.2.1.10.246.1.5.1.2
This variable indicates if the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pwPerf1DayIntervalTimeElapsed 1.3.6.1.2.1.10.246.1.5.1.3
The number of seconds in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason or where agent clock adjustments have been made.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfTimeElapsed  

pwPerf1DayIntervalInHCPackets 1.3.6.1.2.1.10.246.1.5.1.4
High-capacity counter for the total number of packets received by the PW (from the PSN).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pwPerf1DayIntervalInHCBytes 1.3.6.1.2.1.10.246.1.5.1.5
High-capacity counter for the total number of bytes received by the PW (from the PSN).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pwPerf1DayIntervalOutHCPackets 1.3.6.1.2.1.10.246.1.5.1.6
High-capacity counter for the total number of packets forwarded by the PW (to the PSN).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pwPerf1DayIntervalOutHCBytes 1.3.6.1.2.1.10.246.1.5.1.7
High-capacity counter for the total number of bytes forwarded by the PW (to the PSN).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pwPerfTotalErrorPackets 1.3.6.1.2.1.10.246.1.6
Counter for number of errors at the PW processing level, for example, packets received with unknown PW label.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pwIndexMappingTable 1.3.6.1.2.1.10.246.1.7
This table enables the reverse mapping of the unique PWid parameters [peer IP, PW type, and PW ID] and the pwIndex. The table is not applicable for PWs created manually or by using the generalized FEC.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwIndexMappingEntry

pwIndexMappingEntry 1.3.6.1.2.1.10.246.1.7.1
An entry in this table MUST be created by the agent for every PW created by the pwTable for which pwOwner equals pwIdFecSignaling and pwID is not zero. Implementers need to be aware that if the value of the pwIndexMappingPeerAddr (an OID) has more than 113 sub-identifiers, then OIDs of column instances in this table will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwIndexMappingEntry  

pwIndexMappingPwType 1.3.6.1.2.1.10.246.1.7.1.1
The PW type (indicates the service) of this PW.
Status: current Access: not-accessible
OBJECT-TYPE    
  IANAPwTypeTC  

pwIndexMappingPwID 1.3.6.1.2.1.10.246.1.7.1.2
The PW ID of this PW. Zero if the PW is configured manually.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwIDType  

pwIndexMappingPeerAddrType 1.3.6.1.2.1.10.246.1.7.1.3
IP address type of the peer node.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

pwIndexMappingPeerAddr 1.3.6.1.2.1.10.246.1.7.1.4
IP address of the peer node.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

pwIndexMappingPwIndex 1.3.6.1.2.1.10.246.1.7.1.5
The value that represents the PW in the pwTable.
Status: current Access: read-only
OBJECT-TYPE    
  PwIndexType  

pwPeerMappingTable 1.3.6.1.2.1.10.246.1.8
This table provides reverse mapping of the existing PW based on PW type and PW ID ordering. This table is typically useful for the element management system (EMS) ordered query of existing PWs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwPeerMappingEntry

pwPeerMappingEntry 1.3.6.1.2.1.10.246.1.8.1
An entry in this table is created by the agent for every PW entry in the pwTable. Implementers need to be aware that if the value of the pwPeerMappingPeerAddr (an OID) has more than 113 sub-identifiers, then OIDs of column instances in this table will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwPeerMappingEntry  

pwPeerMappingPeerAddrType 1.3.6.1.2.1.10.246.1.8.1.1
IP address type of the peer node.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

pwPeerMappingPeerAddr 1.3.6.1.2.1.10.246.1.8.1.2
IP address of the peer node.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

pwPeerMappingPwType 1.3.6.1.2.1.10.246.1.8.1.3
The PW type (indicates the emulated service) of this PW.
Status: current Access: not-accessible
OBJECT-TYPE    
  IANAPwTypeTC  

pwPeerMappingPwID 1.3.6.1.2.1.10.246.1.8.1.4
The PW ID of this PW. Zero if the PW is configured manually.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwIDType  

pwPeerMappingPwIndex 1.3.6.1.2.1.10.246.1.8.1.5
The value that represents the PW in the pwTable.
Status: current Access: read-only
OBJECT-TYPE    
  PwIndexType  

pwUpDownNotifEnable 1.3.6.1.2.1.10.246.1.9
If this object is set to true(1), then it enables the emission of pwUp and pwDown notifications; otherwise, these notifications are not emitted.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pwDeletedNotifEnable 1.3.6.1.2.1.10.246.1.10
If this object is set to true(1), then it enables the emission of pwDeleted notification; otherwise, this notification is not emitted.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pwNotifRate 1.3.6.1.2.1.10.246.1.11
This object defines the maximum number of PW notifications that can be emitted from the device per second.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

pwGenFecIndexMappingTable 1.3.6.1.2.1.10.246.1.12
This table enables the reverse mapping of the unique PWid parameters [GroupAttachmentID, LocalAttachmentID, and PeerAttachmentID] and the pwIndex. The table is only applicable for PW using the generalized FEC.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwGenFecIndexMappingEntry

pwGenFecIndexMappingEntry 1.3.6.1.2.1.10.246.1.12.1
An entry in this table MUST be created by the agent for every PW created by the pwTable for which pwOwner equals genFecSignaling. Implementers need to be aware that if the combined value of pwGenFecIndexMappingAGI, pwGenFecIndexMappingLocalAII, and pwGenFecIndexMappingRemoteAII (OIDs) has more than 113 sub-identifiers, then OIDs of column instances in this table will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwGenFecIndexMappingEntry  

pwGenFecIndexMappingAGIType 1.3.6.1.2.1.10.246.1.12.1.1
This object is the type of the attachment group identifier (AGI) that this PW belongs to.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwGenIdType  

pwGenFecIndexMappingAGI 1.3.6.1.2.1.10.246.1.12.1.2
This object is an octet string representing the attachment group identifier (AGI) that this PW belongs to, which typically identifies the VPN ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwAttachmentIdentifierType  

pwGenFecIndexMappingLocalAIIType 1.3.6.1.2.1.10.246.1.12.1.3
This object is the type of the local forwarder attachment individual identifier (AII) to be used by this PW.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwGenIdType  

pwGenFecIndexMappingLocalAII 1.3.6.1.2.1.10.246.1.12.1.4
This object is an octet string representing the local forwarder attachment individual identifier (AII) to be used by this PW. It is used as the SAII for outgoing signaling messages and the TAII in the incoming messages from the peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwAttachmentIdentifierType  

pwGenFecIndexMappingRemoteAIIType 1.3.6.1.2.1.10.246.1.12.1.5
This object is the type of the remote forwarder attachment individual identifier (AII) to be used by this PW.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwGenIdType  

pwGenFecIndexMappingRemoteAII 1.3.6.1.2.1.10.246.1.12.1.6
This object is an octet string representing the peer forwarder attachment individual identifier (AII) to be used by this PW. It is used as the TAII for outgoing signaling messages and the SAII in the incoming messages from the peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwAttachmentIdentifierType  

pwGenFecIndexMappingPwIndex 1.3.6.1.2.1.10.246.1.12.1.7
The value that represents the PW in the pwTable.
Status: current Access: read-only
OBJECT-TYPE    
  PwIndexType  

pwDown 1.3.6.1.2.1.10.246.0.1
This notification is generated when the pwOperStatus object for one or more contiguous entries in the pwTable are about to enter the down(2) or lowerLayerDown(6) state from any other state, except for transition from the notPresent(5) state. For the purpose of deciding when these notifications occur, the lowerLayerDown(6) state and the down(2) state are considered to be equivalent; i.e., there is no notification on transition from lowerLayerDown(6) into down(2), and there is a trap on transition from any other state except down(2) (and notPresent) into lowerLayerDown(6). The included values of pwOperStatus MUST each be equal to down(2) or lowerLayerDown(6). The two instances of pwOperStatus in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For cases where a contiguous range of cross-connects have transitioned into the down(2) and lowerLayerDown(6) states at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single cross-connect entry, then the instance identifier (and values) of the two pwOperStatus objects MUST be identical.
Status: current Access: read-only
NOTIFICATION-TYPE    

pwUp 1.3.6.1.2.1.10.246.0.2
This notification is generated when the pwOperStatus object for one or more contiguous entries in the pwTable are about to enter the up(1) state from some other state except the notPresent(5) state and given that the pwDown notification been issued for these entries. The included values of pwOperStatus MUST both be set equal to this new state (i.e., up(1)). The two instances of pwOperStatus in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For cases where a contiguous range of cross-connects have transitioned into the up(1) state at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single cross-connect entry, then the instance identifier (and values) of the two pwOperStatus objects MUST be identical.
Status: current Access: read-only
NOTIFICATION-TYPE    

pwDeleted 1.3.6.1.2.1.10.246.0.3
This notification is generated when the PW has been deleted, i.e., when the pwRowStatus has been set to destroy(6) or the PW has been deleted by a non-MIB application or due to an auto-discovery process.
Status: current Access: read-only
NOTIFICATION-TYPE    

pwGroups 1.3.6.1.2.1.10.246.2.1
OBJECT IDENTIFIER    

pwCompliances 1.3.6.1.2.1.10.246.2.2
OBJECT IDENTIFIER    

pwModuleFullCompliance 1.3.6.1.2.1.10.246.2.2.1
The compliance statement for agents that provide full support for the PW MIB module. Such devices can then be monitored and configured using this MIB module.
Status: current Access: read-only
MODULE-COMPLIANCE    

pwModuleReadOnlyCompliance 1.3.6.1.2.1.10.246.2.2.2
The compliance statement for agents that provide read- only support for the PW MIB module. Such devices can then be monitored but cannot be configured using this MIB module.
Status: current Access: read-only
MODULE-COMPLIANCE    

pwBasicGroup 1.3.6.1.2.1.10.246.2.1.1
Collection of objects that are required in all implementations that support the PW MIB module.
Status: current Access: read-only
OBJECT-GROUP    

pwPwIdGroup 1.3.6.1.2.1.10.246.2.1.2
Collection of objects required for PW ID configuration and signaling.
Status: current Access: read-only
OBJECT-GROUP    

pwGeneralizedFecGroup 1.3.6.1.2.1.10.246.2.1.3
Collection of objects required for generalized FEC configuration and signaling.
Status: current Access: read-only
OBJECT-GROUP    

pwFcsGroup 1.3.6.1.2.1.10.246.2.1.4
Collection of objects required for FCS retention configuration and signaling.
Status: current Access: read-only
OBJECT-GROUP    

pwFragGroup 1.3.6.1.2.1.10.246.2.1.5
Collection of objects required for fragmentation configuration and signaling.
Status: current Access: read-only
OBJECT-GROUP    

pwPwStatusGroup 1.3.6.1.2.1.10.246.2.1.6
Collection of objects required for PW status configuration and signaling.
Status: current Access: read-only
OBJECT-GROUP    

pwGetNextGroup 1.3.6.1.2.1.10.246.2.1.7
Collection of objects for getting the next available index.
Status: current Access: read-only
OBJECT-GROUP    

pwPriorityGroup 1.3.6.1.2.1.10.246.2.1.8
Collection of objects for controlling the PW setup and holding priority.
Status: current Access: read-only
OBJECT-GROUP    

pwAttachmentGroup 1.3.6.1.2.1.10.246.2.1.9
Collection of objects for PW configuration as ifIndex.
Status: current Access: read-only
OBJECT-GROUP    

pwPerformanceGeneralGroup 1.3.6.1.2.1.10.246.2.1.10
Collection of general objects needed for managing the total running performance parameters.
Status: current Access: read-only
OBJECT-GROUP    

pwPeformance1DayIntervalGroup 1.3.6.1.2.1.10.246.2.1.11
Collection of objects needed for a PW running 1-day interval performance collection.
Status: current Access: read-only
OBJECT-GROUP    

pwPerformanceIntervalGeneralGroup 1.3.6.1.2.1.10.246.2.1.12
Collection of general objects needed for managing the interval performance parameters.
Status: current Access: read-only
OBJECT-GROUP    

pwPeformanceIntervalGroup 1.3.6.1.2.1.10.246.2.1.13
Collection of 32-bit objects needed for PW performance collection in 15-minute intervals.
Status: current Access: read-only
OBJECT-GROUP    

pwHCPeformanceIntervalGroup 1.3.6.1.2.1.10.246.2.1.14
Collection of HC objects needed for PW performance collection in 15-minute intervals.
Status: current Access: read-only
OBJECT-GROUP    

pwMappingTablesGroup 1.3.6.1.2.1.10.246.2.1.15
Collection of objects contained in the reverse mapping tables.
Status: current Access: read-only
OBJECT-GROUP    

pwNotificationControlGroup 1.3.6.1.2.1.10.246.2.1.16
Collection of objects for controlling the PW notifications.
Status: current Access: read-only
OBJECT-GROUP    

pwNotificationGroup 1.3.6.1.2.1.10.246.2.1.17
Collection of PW notifications objects.
Status: current Access: read-only
NOTIFICATION-GROUP    

pwSignalingGroup 1.3.6.1.2.1.10.246.2.1.18
Collection of objects for use in implementations that support the PW signaling.
Status: current Access: read-only
OBJECT-GROUP