QB-DWS-MIB

File: QB-DWS-MIB.mib (60348 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
IF-MIB	QUANTUMBRIDGE-REG	QBSYS-SYSTEM-MIB
ATM-TC-MIB

Imported symbols

NOTIFICATION-TYPE	MODULE-IDENTITY	OBJECT-TYPE
Gauge32	Counter32	Unsigned32
Integer32	TimeTicks	IpAddress
TEXTUAL-CONVENTION	TruthValue	TimeStamp
RowStatus	DisplayString	MODULE-COMPLIANCE
OBJECT-GROUP	InterfaceIndex	InterfaceIndexOrZero
ifIndex	qbMibs	qbSysModuleSlot
qbSysIotSerialNumber	AtmAddr	AtmConnKind
AtmConnCastType	AtmServiceCategory	AtmTrafficDescrParamIndex
AtmVpIdentifier	AtmVcIdentifier	AtmVorXAdminStatus
AtmVorXLastChange	AtmVorXOperStatus	atmNoClpNoScr

Defined Types

QbPvcConnKind
A connection type that can be provisioned.
TEXTUAL-CONVENTION
	INTEGER	unknown(0), atmPvcToPvc(1), atmPvpToPvp(2), iotE1ToAtm(3), iotDs1ToAtm(4), iotEnetToAtm(5), vt15ToAtm(6), vc12ToAtm(7), vt15Vt15(8), vc12ToVc12(9), iotE1ToVt15(10), iotDs1ToVt15(11), iotE1ToVc12(12), iotDs1ToVc12(13), iotE1ToIotE1(14), iotDs1ToIotDs1(15), iotEnetToIotEnet(16), vc11ToAtm(17), iotDs1ToVc11(18), vc11ToVc11(19), m13ToAtm(20), iotDs1ToM13(21), m13ToM13(22), atmToEnet(23), atmToDs1(24), atmToE1(25), ds1ToVt15(26), e1ToVc12(27), ds1ToVc11(28), ds1ToM13(29), ds1ToDs1(30), e1ToE1(31), enetToEnet(32), iotDs1ToDs1(33), iotE1ToE1(34), iotEnetToEnet(35), vlanToAtm(36), vlanToGige(37), vlanToIotEnet(38), vlanToEnet(39)

QbBitRate
A data rate in bits/second.
TEXTUAL-CONVENTION
	Gauge32

QbSerialNum
The IOT serial number.
TEXTUAL-CONVENTION
	Unsigned32	0..32

QbDwsIfStatus
The status of the DWS Interface
TEXTUAL-CONVENTION
	INTEGER	ok(1), rxFailure(2), txFailure(3), unknown(4)

QbDwsSrvStatus
The service status of the DWS Interface
TEXTUAL-CONVENTION
	INTEGER	avilable(1), empty(2), almostFull(3), overflown(4)

QbAtmAal5EncapsType
The type of data encapsulation used over the AAL5 layer.
TEXTUAL-CONVENTION
	INTEGER	qbVcMultiplexRoutedProto(1), qbBridgedProto8023EncapFcs(2), qbBridgedProto8023EncapsNoFcs(3), qbBridgedPropEncaps(4), qbBridgedProtoLLCEncapsNoFcs(5), qbRoutedEncapsNoHdrNoFcs(6)

QbEnableStatus
enable(1) or disable(1) operations.
TEXTUAL-CONVENTION
	INTEGER	enable(1), disable(2)

QbDwsNetEntry
SEQUENCE
	qbDwsNetIfIndex	InterfaceIndex
	qbDwsNetBw	QbBitRate
	qbDwsNetAllocatedBw	QbBitRate
	qbDwsNetAvailableBw	QbBitRate
	qbDwsNetAllocatedUbrBw	QbBitRate
	qbDwsNetAllocatedCbrBw	QbBitRate
	qbDwsNetNumCbrConn	Integer32
	qbDwsNetNumUbrConn	Integer32
	qbDwsNetNumIot	Integer32
	qbDwsNetTxStatus	QbDwsIfStatus
	qbDwsNetTxStatusLastChange	TimeStamp
	qbDwsNetLosIotAddr	Integer32
	qbDwsNetLosIotTime	TimeStamp
	qbDwsNetEncryptStatus	TruthValue
	qbDwsNetRangeMode	INTEGER
	qbDwsNetRxTsCount	Counter32
	qbDwsNetTxTsCount	Counter32
	qbDwsNetRxMissingTs	Counter32
	qbDwsNetRxIllegalTs	Counter32
	qbDwsNetTxJabberTs	Counter32
	qbDwsNetTxOutOfFrameTs	Counter32
	qbDwsNetTxHdrCrcTsErrs	Counter32
	qbDwsNetOamRequests	Counter32
	qbDwsNetOamResponses	Counter32
	qbDwsNetOamEvents	Counter32
	qbDwsNetOamBadMsgs	Counter32
	qbDwsNetLoopBack	INTEGER

QbDwsIotIfConfEntry
SEQUENCE
	qbDwsIotIfIndex	InterfaceIndex
	qbDwsIotNetIfIndex	InterfaceIndex
	qbDwsIotIfAddr	Integer32
	qbDwsIotIfConfPowerLevel	Integer32
	qbDwsIotIfConfEqDelay	TimeTicks
	qbDwsIotIfConfWaveLength	Integer32
	qbDwsIotIfUbrBw	QbBitRate
	qbDwsIotIfCbrBw	QbBitRate
	qbDwsIotIfTxStatus	QbDwsIfStatus
	qbDwsIotIfTxStatusLastChange	TimeStamp
	qbDwsIotIfLastRangeTime	TimeStamp

QbDwsIotIfStatsEntry
SEQUENCE
	qbDwsIotIfStatsUtil	INTEGER
	qbDwsIotIfStatsOamRequests	Counter32
	qbDwsIotIfStatsOamResponses	Counter32
	qbDwsIotIfStatsOamEvents	Counter32
	qbDwsIotIfStatsOamBadMsgs	Counter32
	qbDwsIotIfStatsCrcErrs	Counter32
	qbDwsIotIfStatsTsHdrParityErrs	Counter32
	qbDwsIotIfStatsFrameLossErrs	Counter32
	qbDwsIotIfStatsSignalLossErrs	Counter32
	qbDwsIotIfStatsRxAal1Cells	Counter32
	qbDwsIotIfStatsTxAal1Cells	Counter32

QbIotPktIfConfEntry
SEQUENCE
	qbIotPktIfConfIndex	InterfaceIndex
	qbAtmIfIndex	InterfaceIndex
	qbIotPktIfConfVpi	AtmVpIdentifier
	qbIotPktIfConfVci	AtmVcIdentifier
	qbIotPktIfConfConnName	DisplayString
	qbIotPktIfConfRxTrafficDescrIndex	AtmTrafficDescrParamIndex
	qbIotPktIfConfTxTrafficDescrIndex	AtmTrafficDescrParamIndex
	qbIotPktIfConfAdminStatus	AtmVorXAdminStatus
	qbIotPktIfConfOperStatus	AtmVorXOperStatus
	qbIotPktIfConfRowStatus	RowStatus
	qbIotPktIfConfLoopback	QbEnableStatus
	qbIotPktIfConfConnKind	QbPvcConnKind

QbIotAddrEntry
SEQUENCE
	qbIotAddr	Integer32
	qbIotSerialNum	QbSerialNum

QbIotPortCrossConnEntry
SEQUENCE
	qbIotPortCrossConnEndpt1IfIndex	InterfaceIndex
	qbIotPortCrossConnEndpt2IfIndex	InterfaceIndex
	qbIotPortCrossConnAdminStatus	AtmVorXAdminStatus
	qbIotPortCrossConnOperStatus	AtmVorXOperStatus
	qbIotPortCrossConnLastChange	AtmVorXLastChange
	qbIotPortCrossConnRxTrafficDescrIndex	AtmTrafficDescrParamIndex
	qbIotPortCrossConnTxTrafficDescrIndex	AtmTrafficDescrParamIndex
	qbIotPortCrossConnName	DisplayString
	qbIotPortCrossConnRowStatus	RowStatus
	qbIotPortCrossConnLoopback	QbEnableStatus
	qbIotPortCrossConnLoopbackEndpt	INTEGER
	qbIotPortCrossConnKind	QbPvcConnKind

QbTContEntry
SEQUENCE
	qbTContIndex	INTEGER
	qbTContType	INTEGER
	qbTContMaxBw	INTEGER
	qbTContFixedBw	INTEGER
	qbTContAssuredBw	INTEGER
	qbTContGrantNum	INTEGER

Defined Values

qbDwsMIB		1.3.6.1.4.1.4323.2.3
This module defines additional objects for the provisioning and management of DWS links in Quantum bridge devices.
MODULE-IDENTITY

qbDwsObjects		1.3.6.1.4.1.4323.2.3.1
OBJECT IDENTIFIER

qbDwsNotifications		1.3.6.1.4.1.4323.2.3.2
OBJECT IDENTIFIER

qbDwsConformance		1.3.6.1.4.1.4323.2.3.3
OBJECT IDENTIFIER

qbDwsNetGroup		1.3.6.1.4.1.4323.2.3.1.1
OBJECT IDENTIFIER

qbDwsIotIfGroup		1.3.6.1.4.1.4323.2.3.1.2
OBJECT IDENTIFIER

qbIotPktIfGroup		1.3.6.1.4.1.4323.2.3.1.3
OBJECT IDENTIFIER

qbIotAddrGroup		1.3.6.1.4.1.4323.2.3.1.4
OBJECT IDENTIFIER

qbIotPortCrossConnGroup		1.3.6.1.4.1.4323.2.3.1.5
OBJECT IDENTIFIER

qbTContGroup		1.3.6.1.4.1.4323.2.3.1.6
OBJECT IDENTIFIER

qbDwsSysRangeMode		1.3.6.1.4.1.4323.2.3.1.1.1
The object that indicates a system wide range mode. When read, this object always returns the value 'ready(1)'. Setting this object to rangeAll(2) causes ranging of all IOTs that connect to this OAS.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ready(1), rangeAll(2)

qbSysIotRecoverMode		1.3.6.1.4.1.4323.2.3.1.1.2
The object allows to set the IOT auto-recovery feature on the IOAS. Auto-recovery is global in scope, so when it is enabled, auto-recovery is attempted for all IOTs that are attached to the IOAS.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

qbDwsNetTable		1.3.6.1.4.1.4323.2.3.1.1.3
The Quantum Bridge PON Interface Table contains extensions of the standard MIB Interface Table, one entry per IOAS DWS interface. The table contains read-only objects and shows MIB objects for every Network interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QbDwsNetEntry

qbDwsNetEntry		1.3.6.1.4.1.4323.2.3.1.1.3.1
An entry in the Quantum Bridge DWS Interface Table that contains the Network interface's specific objects.
Status: current	Access: not-accessible
OBJECT-TYPE
	QbDwsNetEntry

qbDwsNetIfIndex		1.3.6.1.4.1.4323.2.3.1.1.3.1.1
The value of this object is the same as the corresponding ifIndex of the Network Interface in the ifTable.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

qbDwsNetBw		1.3.6.1.4.1.4323.2.3.1.1.3.1.2
The object indicates the total bandwidth rate that is available for reservation on this interface. This object is specified in Bits per second.
Status: current	Access: read-only
OBJECT-TYPE
	QbBitRate

qbDwsNetAllocatedBw		1.3.6.1.4.1.4323.2.3.1.1.3.1.3
The object indicates the total bandwidth rate that is currently subscribed. The subscribed bandwidth rate consists of the bandwidth rate allocated for all provisoned connections. This object is specified in Bits per sec(Bps).
Status: current	Access: read-only
OBJECT-TYPE
	QbBitRate

qbDwsNetAvailableBw		1.3.6.1.4.1.4323.2.3.1.1.3.1.4
The portion of this interface's capacity in bits per sec that is available for data traffic. This variable is adjusted for the allocated bandwidth. The formula for calculating this value is qbDwsNetBw - qbDwsNetAllocatedBw This object is specified in Bps.
Status: current	Access: read-only
OBJECT-TYPE
	QbBitRate

qbDwsNetAllocatedUbrBw		1.3.6.1.4.1.4323.2.3.1.1.3.1.5
The object indicates the total number of bandwidth that are currently allocated for packet/ubr traffic. This object is specified in Bps.
Status: current	Access: read-only
OBJECT-TYPE
	QbBitRate

qbDwsNetAllocatedCbrBw		1.3.6.1.4.1.4323.2.3.1.1.3.1.6
The object indicates the total number of bandwidth that is currently allocated for CBR traffic. This object is specified in Bps.
Status: current	Access: read-only
OBJECT-TYPE
	QbBitRate

qbDwsNetNumCbrConn		1.3.6.1.4.1.4323.2.3.1.1.3.1.7
The object indicates the total number of inactive and in-service CBR connections that are currently provisioned on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

qbDwsNetNumUbrConn		1.3.6.1.4.1.4323.2.3.1.1.3.1.8
The object indicates the total number of inactive and in-serice UBR connections that are currently provisioned on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

qbDwsNetNumIot		1.3.6.1.4.1.4323.2.3.1.1.3.1.9
The number of IOTs that are provisioned on the Network interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

qbDwsNetTxStatus		1.3.6.1.4.1.4323.2.3.1.1.3.1.10
This objects indicates the status of the DWS transmitter. The trap is generated by the SNMP agent when the IOAS DWS transmitter problem is detected. The trap contains the DWS module interface index.
Status: current	Access: read-only
OBJECT-TYPE
	QbDwsIfStatus

qbDwsNetTxStatusLastChange		1.3.6.1.4.1.4323.2.3.1.1.3.1.11
The value of MIB II's sysUpTime object at the time this DWS Interface entered its current status state.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

qbDwsNetLosIotAddr		1.3.6.1.4.1.4323.2.3.1.1.3.1.12
The object contains the address of the IOT for which a Los condition is detected. This indicates that no signal was detected within the expected time slot window. Note: The Los indication at the IOAS DWS card is a signal that an IOT is non-functioning.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

qbDwsNetLosIotTime		1.3.6.1.4.1.4323.2.3.1.1.3.1.13
The value of MIB II's sysUpTime object at the time when the qbDwsNetIotLos condition was detected.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

qbDwsNetEncryptStatus		1.3.6.1.4.1.4323.2.3.1.1.3.1.14
The object that enables and disables encryption on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

qbDwsNetRangeMode		1.3.6.1.4.1.4323.2.3.1.1.3.1.15
The object that indicates a range mode. When read, this object always returns the value 'ready(1)'. Setting this object to rangeAll(2) causes ranging of all IOTs connected to this interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ready(1), rangeAll(2)

qbDwsNetRxTsCount		1.3.6.1.4.1.4323.2.3.1.1.3.1.16
The total number of successfully received time slots.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsNetTxTsCount		1.3.6.1.4.1.4323.2.3.1.1.3.1.17
The total number of successfully transmitted time slots.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsNetRxMissingTs		1.3.6.1.4.1.4323.2.3.1.1.3.1.18
The number received time slots that have been missed.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsNetRxIllegalTs		1.3.6.1.4.1.4323.2.3.1.1.3.1.19
The number illegal received time slots that have been detected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsNetTxJabberTs		1.3.6.1.4.1.4323.2.3.1.1.3.1.20
The number jabber transmitted time slots that have been detected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsNetTxOutOfFrameTs		1.3.6.1.4.1.4323.2.3.1.1.3.1.21
The number out of frame transmitted timeslots that have been detected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsNetTxHdrCrcTsErrs		1.3.6.1.4.1.4323.2.3.1.1.3.1.22
The number transmitted timeslots with the header protection error that have been detected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsNetOamRequests		1.3.6.1.4.1.4323.2.3.1.1.3.1.23
The number of OAM requests. These OAM requests are originated by the IOAS and sent to downstream IOTs.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsNetOamResponses		1.3.6.1.4.1.4323.2.3.1.1.3.1.24
The number of OAM responses. These responses are generated by IOTs in response to downstream requests.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsNetOamEvents		1.3.6.1.4.1.4323.2.3.1.1.3.1.25
The number of OAM events. These events are originated by IOT devices to signal abnormal conditions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsNetOamBadMsgs		1.3.6.1.4.1.4323.2.3.1.1.3.1.26
The total number of bad OAM messages.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsNetLoopBack		1.3.6.1.4.1.4323.2.3.1.1.3.1.27
The Loopback status of this DWS port. Writing configures the port to go into the loopback mode. When placed in loopback mode the DWS port does a 'payload' loopback.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

qbDwsIotIfConfTable		1.3.6.1.4.1.4323.2.3.1.2.1
The Quantum DWS interface table. One entry per each IOT's DWS interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QbDwsIotIfConfEntry

qbDwsIotIfConfEntry		1.3.6.1.4.1.4323.2.3.1.2.1.1
An entry in the Quantum Bridge DWS Interface Table. The ifIndex is a DWS interface index from ifTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	QbDwsIotIfConfEntry

qbDwsIotIfIndex		1.3.6.1.4.1.4323.2.3.1.2.1.1.1
The ifIndex of this interface in the ifTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

qbDwsIotNetIfIndex		1.3.6.1.4.1.4323.2.3.1.2.1.1.2
The ifIndex of this PON interface in the ifTable.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

qbDwsIotIfAddr		1.3.6.1.4.1.4323.2.3.1.2.1.1.3
The IOT terminal address.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

qbDwsIotIfConfPowerLevel		1.3.6.1.4.1.4323.2.3.1.2.1.1.4
The DWS interface's power level.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

qbDwsIotIfConfEqDelay		1.3.6.1.4.1.4323.2.3.1.2.1.1.5
The equal Delay time (in hundredths of a second).
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

qbDwsIotIfConfWaveLength		1.3.6.1.4.1.4323.2.3.1.2.1.1.6
The wave length value for this DWS interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

qbDwsIotIfUbrBw		1.3.6.1.4.1.4323.2.3.1.2.1.1.7
The object indicates the total UBR bandwidth rate that is reserved for a given IOT interface. This object is specified in Bits per second.
Status: current	Access: read-only
OBJECT-TYPE
	QbBitRate

qbDwsIotIfCbrBw		1.3.6.1.4.1.4323.2.3.1.2.1.1.8
The object indicates the total CBR bandwidth rate that is reserved for a given IOT interface. This object is specified in Bits per second.
Status: current	Access: read-only
OBJECT-TYPE
	QbBitRate

qbDwsIotIfTxStatus		1.3.6.1.4.1.4323.2.3.1.2.1.1.9
This objects indicates the status of the IOT DWS Port. The txFailure(2) state indicates that the laser transmitter failed. The rxFailure(3) state indicates that no signal was detected within the expected timeslot window. It signals that there is a problem with the DWS port receiver. When this object is changed, the ifOperStatus and ifLastChnaged of this interface must also be changed. Note: The trap is generated by the SNMP agent when the IOT DWS status is changed. The trap contains the IOAS DWS card interface index and IOT address.
Status: current	Access: read-only
OBJECT-TYPE
	QbDwsIfStatus

qbDwsIotIfTxStatusLastChange		1.3.6.1.4.1.4323.2.3.1.2.1.1.10
The value of MIB II's sysUpTime object at the time this DWS Interface enters its current status state.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

qbDwsIotIfLastRangeTime		1.3.6.1.4.1.4323.2.3.1.2.1.1.11
The value of MIB II's sysUpTime object at the last time when this IOT is ranged
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

qbDwsIotIfStatsTable		1.3.6.1.4.1.4323.2.3.1.2.2
The Quantum Bridge IOT's terminal table. One entry per each RT.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QbDwsIotIfStatsEntry

qbDwsIotIfStatsEntry		1.3.6.1.4.1.4323.2.3.1.2.2.1
An entry in the Quantum DWS Interface Statistics Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	QbDwsIotIfStatsEntry

qbDwsIotIfStatsUtil		1.3.6.1.4.1.4323.2.3.1.2.2.1.1
The object indicates the utilization of the Network Interface transmission rate capacity by the IOT DWS interface. This object is specified in percents.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..100

qbDwsIotIfStatsOamRequests		1.3.6.1.4.1.4323.2.3.1.2.2.1.2
The number of received downstream OAM request messages.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsIotIfStatsOamResponses		1.3.6.1.4.1.4323.2.3.1.2.2.1.3
The number of transmitted upstream OAM response messages.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsIotIfStatsOamEvents		1.3.6.1.4.1.4323.2.3.1.2.2.1.4
The number of OAM event messages originated by the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsIotIfStatsOamBadMsgs		1.3.6.1.4.1.4323.2.3.1.2.2.1.5
The number of wrong OAM messages received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsIotIfStatsCrcErrs		1.3.6.1.4.1.4323.2.3.1.2.2.1.6
The summary number of the IOT DWS CRC subframe and time slot header CRC errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsIotIfStatsTsHdrParityErrs		1.3.6.1.4.1.4323.2.3.1.2.2.1.7
The number of Time Slot header parity errors that have been detected on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsIotIfStatsFrameLossErrs		1.3.6.1.4.1.4323.2.3.1.2.2.1.8
The number of Loss frame errors that have been detected on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsIotIfStatsSignalLossErrs		1.3.6.1.4.1.4323.2.3.1.2.2.1.9
The number of Loss signal errors that have been detected on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsIotIfStatsRxAal1Cells		1.3.6.1.4.1.4323.2.3.1.2.2.1.10
The number of received AAL1 ATM cells.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbDwsIotIfStatsTxAal1Cells		1.3.6.1.4.1.4323.2.3.1.2.2.1.11
The number of transmitted ATM cells .
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

qbIotPktIfConfTable		1.3.6.1.4.1.4323.2.3.1.3.1
The Quantum Bridge PKT configuration table contains cross-connections between Ethernet interfaces and corresponding PVC/AAL5 that are configured at a WAN port. An entry in the table may be created, destroyed or modified. This table lists all PVCs within the System that send/receive packet traffic to/from the ATM cloud.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QbIotPktIfConfEntry

qbIotPktIfConfEntry		1.3.6.1.4.1.4323.2.3.1.3.1.1
An entry in the Quantum Bridge IP configuration table. For every IP traffic flow, there is a corresponding row in this table which contains a DWS interface index, and a VPI/VCI pair of PVC configured at a SONET port for a given DWS interface. The creation of a row in this table causes a corresponding entry in the atmVclTable of the ATM-MIB to be automatically created if an atmVclEntry with qbPktIotIfConfVpi and qbPktIotIfConfVci values does not exist. This corresponding entry can be removed only if the qbPktIotIfConfEntry is removed. The qbPktIotIfConfIndex of this table is an ifIndex of the DWS interface from the ifTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	QbIotPktIfConfEntry

qbIotPktIfConfIndex		1.3.6.1.4.1.4323.2.3.1.3.1.1.1
An interface index of the Ethernet port interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

qbAtmIfIndex		1.3.6.1.4.1.4323.2.3.1.3.1.1.2
An interface index of the ATM interface that is stacked on top of the WAN/SONET interface.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndex

qbIotPktIfConfVpi		1.3.6.1.4.1.4323.2.3.1.3.1.1.3
A VPI of the AAL5 PVC that connects this interface to the ATM cloud. This PVC is automatically configured at the SONET port of the WAN card (atmVclTable).
Status: current	Access: read-create
OBJECT-TYPE
	AtmVpIdentifier

qbIotPktIfConfVci		1.3.6.1.4.1.4323.2.3.1.3.1.1.4
A VCI of the AAL5 bi-directional PVC that connects this interface to the ATM cloud. This PVC is automatically configured or removed at the SONET port of the WAN card (atmVclTable).
Status: current	Access: read-create
OBJECT-TYPE
	AtmVcIdentifier

qbIotPktIfConfConnName		1.3.6.1.4.1.4323.2.3.1.3.1.1.5
The textual name of the connection(PVC) as specified by a user. It provides a non-volatile handle for this PVC. The supplied name in the qbPktIotIfConfPvcName is associated with the same PVC for as long as that PVC/conection remains.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..20)

qbIotPktIfConfRxTrafficDescrIndex		1.3.6.1.4.1.4323.2.3.1.3.1.1.6
The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this VCL.
Status: current	Access: read-create
OBJECT-TYPE
	AtmTrafficDescrParamIndex

qbIotPktIfConfTxTrafficDescrIndex		1.3.6.1.4.1.4323.2.3.1.3.1.1.7
The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this VCL.
Status: current	Access: read-create
OBJECT-TYPE
	AtmTrafficDescrParamIndex

qbIotPktIfConfAdminStatus		1.3.6.1.4.1.4323.2.3.1.3.1.1.8
The desired administrative status of the packet connection The up and down states indicate that the traffic flow is enabled or disabled respectively across the ATM cloud.
Status: current	Access: read-create
OBJECT-TYPE
	AtmVorXAdminStatus

qbIotPktIfConfOperStatus		1.3.6.1.4.1.4323.2.3.1.3.1.1.9
The current operational status of the connect.
Status: current	Access: read-only
OBJECT-TYPE
	AtmVorXOperStatus

qbIotPktIfConfRowStatus		1.3.6.1.4.1.4323.2.3.1.3.1.1.10
The status column for this IOT ENET interface. This OBJECT can be set to: createAndGo(4) destroy(6) The following values may be read: active(1) This object may only be set to createAndGo(4). Setting this object to active(1) when its value is already active(1) is a no-op. Setting this object to createAndGo(4) causes the agent to attempt to create and commit the row based on the contents of the objects in the row. If all necessary information is present in the row and the values are acceptable to the agent, the agent will change the status to active(1). If any of the necessary objects are not available, the agent will reject the creation request. Setting this object to destroy(6) will remove the corresponding entry in this table, and disable data traffic.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

qbIotPktIfConfLoopback		1.3.6.1.4.1.4323.2.3.1.3.1.1.11
This object enables loopback on the IOT ENET enedpoint.
Status: current	Access: read-create
OBJECT-TYPE
	QbEnableStatus

qbIotPktIfConfConnKind		1.3.6.1.4.1.4323.2.3.1.3.1.1.12
The PVC connection type.
Status: current	Access: read-create
OBJECT-TYPE
	QbPvcConnKind

qbIotAddrTable		1.3.6.1.4.1.4323.2.3.1.4.1
The Quantum Bridge IOT address table. This table contains information to convert an IOT's address into an IOT's serial number. This table has two indexes: 1. Interface index of the IOAS interface to which a terminal connects. The interface identified by a particular value of this index is the same as the interface identified by the same value of ifIndex. 2. IOT terminal address. A row exists in this table for each discovered IOT terminal. Whenever an IOT is discovered a row is added to the table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QbIotAddrEntry

qbIotAddrEntry		1.3.6.1.4.1.4323.2.3.1.4.1.1
For every IOT terminal there is a row in this table. This contains the IOT address and serial number.
Status: current	Access: not-accessible
OBJECT-TYPE
	QbIotAddrEntry

qbIotAddr		1.3.6.1.4.1.4323.2.3.1.4.1.1.1
The IOT's address.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

qbIotSerialNum		1.3.6.1.4.1.4323.2.3.1.4.1.1.2
The IOT's serial number.
Status: current	Access: read-only
OBJECT-TYPE
	QbSerialNum

qbIotPortCrossConnTable		1.3.6.1.4.1.4323.2.3.1.5.1
The Quantum Bridge IOT port cross-connection table. This table defines all IOT port point-to-point cross-connections within a single OAS system. The connection can be set between two Ethernet, two DS1 or two E1 ports on different IOTs. The table has two indexes: the interface index of the first end-point and the interface index of the second endpoint. Note: Connections that are listed in this table are not reflected in the atmVclTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QbIotPortCrossConnEntry

qbIotPortCrossConnEntry		1.3.6.1.4.1.4323.2.3.1.5.1.1
An entry in the Quantum Bridge qbIotPortConnTable two contains a connection between the same port type of different IOTs.
Status: current	Access: not-accessible
OBJECT-TYPE
	QbIotPortCrossConnEntry

qbIotPortCrossConnEndpt1IfIndex		1.3.6.1.4.1.4323.2.3.1.5.1.1.1
The ifIndex of the first IOT port((end-point) for the configured IOT cross-connect.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

qbIotPortCrossConnEndpt2IfIndex		1.3.6.1.4.1.4323.2.3.1.5.1.1.2
The ifIndex of the second IOT port(end-point) for the configured IOT cross-connect.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

qbIotPortCrossConnAdminStatus		1.3.6.1.4.1.4323.2.3.1.5.1.1.3
The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this VCL.
Status: current	Access: read-create
OBJECT-TYPE
	AtmVorXAdminStatus

qbIotPortCrossConnOperStatus		1.3.6.1.4.1.4323.2.3.1.5.1.1.4
The current operational status of the connection.
Status: current	Access: read-only
OBJECT-TYPE
	AtmVorXOperStatus

qbIotPortCrossConnLastChange		1.3.6.1.4.1.4323.2.3.1.5.1.1.5
The value of sysUpTime at the time this connection entered its current operational state.
Status: current	Access: read-only
OBJECT-TYPE
	AtmVorXLastChange

qbIotPortCrossConnRxTrafficDescrIndex		1.3.6.1.4.1.4323.2.3.1.5.1.1.6
The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this connection.
Status: current	Access: read-create
OBJECT-TYPE
	AtmTrafficDescrParamIndex

qbIotPortCrossConnTxTrafficDescrIndex		1.3.6.1.4.1.4323.2.3.1.5.1.1.7
The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this connection.
Status: current	Access: read-create
OBJECT-TYPE
	AtmTrafficDescrParamIndex

qbIotPortCrossConnName		1.3.6.1.4.1.4323.2.3.1.5.1.1.8
The textual name of the connection as specified by a user. It provides a non-volatile handle for this connection. The supplied name in the qbIotPortConnName is associated with the same connection for as long as that conection remains.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..20)

qbIotPortCrossConnRowStatus		1.3.6.1.4.1.4323.2.3.1.5.1.1.9
The status of the port connect entry. Changing the value of this object from 'active' to 'destroy' will remove this entry from the database. It will disrupt traffic between two IOT packet interfaces.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

qbIotPortCrossConnLoopback		1.3.6.1.4.1.4323.2.3.1.5.1.1.10
This object enables loopback on this IOT to IOT port enedpoint. The endpoint on which loopback is enabled is defined by qbIotPortCrossConnLoopbackEndpt.
Status: current	Access: read-create
OBJECT-TYPE
	QbEnableStatus

qbIotPortCrossConnLoopbackEndpt		1.3.6.1.4.1.4323.2.3.1.5.1.1.11
This object defines loopback on the selected endpoint.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	endPt1(1), endPt2(2)

qbIotPortCrossConnKind		1.3.6.1.4.1.4323.2.3.1.5.1.1.12
The VCL connection type.
Status: current	Access: read-create
OBJECT-TYPE
	QbPvcConnKind

qbTContNumber		1.3.6.1.4.1.4323.2.3.1.6.1
The total number of provisioned Ethernet to ATM PVCs.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

qbNextFreeTContIndex		1.3.6.1.4.1.4323.2.3.1.6.2
The next available Container index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

qbTContTable		1.3.6.1.4.1.4323.2.3.1.6.3
The Quantum Bridge Traffic Container table(TCons) contains traffic containers of IOTs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QbTContEntry

qbTContEntry		1.3.6.1.4.1.4323.2.3.1.6.3.1
An entry in the qbTContTable. There is one entry in the table per IOT on the PON for Release 3.0. The creation of a row in the qbSysIotTable causes a corresponding entry in this table to be automatically created. The deletion of a row in the qbSysIotTable causes a corresponding entry in this table to be automatically removed.
Status: current	Access: not-accessible
OBJECT-TYPE
	QbTContEntry

qbTContIndex		1.3.6.1.4.1.4323.2.3.1.6.3.1.1
The value of this object identifies the row of the Traffic Container Table. Note tht this value can be set to 1 only for Release 3.0.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

qbTContType		1.3.6.1.4.1.4323.2.3.1.6.3.1.2
The Traffic container type. Note that this object can be set to type1 for Release 3.0
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	type1(1), type2(2), type3(3), type4(4), type5(5)

qbTContMaxBw		1.3.6.1.4.1.4323.2.3.1.6.3.1.3
The maximum bandwidth to be assigned to this TCONT. Note that the read-only access is supported for Release 3.0
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

qbTContFixedBw		1.3.6.1.4.1.4323.2.3.1.6.3.1.4
The lower limit of bandwidth for this TCONT.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

qbTContAssuredBw		1.3.6.1.4.1.4323.2.3.1.6.3.1.5
The guaranteed minimum bandwidth for this TCONT. TCONT. Note that the read-only access is supported for Release 3.0
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

qbTContGrantNum		1.3.6.1.4.1.4323.2.3.1.6.3.1.6
FSAN grant number that is assigned to this TCONT. Note that the read-only access is supported for Release 3.0
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

qbDwsNotificationPrefix		1.3.6.1.4.1.4323.2.3.2.0
OBJECT IDENTIFIER

qbDwsIotRxLos		1.3.6.1.4.1.4323.2.3.2.0.1
A qbDwsIotRxLos trap indicates Loss of Signal by the IOT's. This trap is generated by an IOT when Analog DS1/E1 Analog or Digital Los occur.
Status: current	Access: read-write
NOTIFICATION-TYPE

qbDwsRxIoasLos		1.3.6.1.4.1.4323.2.3.2.0.2
A qbDwsRxIoasLos trap indicates Loss of Signal by the IOAS's DWS receiver. This trap is generated by an IOAS DWS card when no signal from an IOT is detected within the timeslot window.
Status: current	Access: read-write
NOTIFICATION-TYPE

qbDwsIoasTxFailure		1.3.6.1.4.1.4323.2.3.2.0.3
A qbDwsTxFailure trap indicates that the IOAS card transmitter does not work. The trap is generated by an IOAS card when the IOAS DWS card transmitter problem is detected. The trap contains the DWS card interface index.
Status: current	Access: read-write
NOTIFICATION-TYPE

qbDwsIotRangeTimeout		1.3.6.1.4.1.4323.2.3.2.0.4
A qbDwsTxFailure trap indicates that IOT not responding during the ranging process.
Status: current	Access: read-write
NOTIFICATION-TYPE

qbDwsCompliances		1.3.6.1.4.1.4323.2.3.3.1
OBJECT IDENTIFIER

qbDwsGroups		1.3.6.1.4.1.4323.2.3.3.2
OBJECT IDENTIFIER

qbDwsCompliance		1.3.6.1.4.1.4323.2.3.3.1.1
The compliance statement for all agents that support this MIB. A compliant agent implements all objects defined in this MIB.
Status: current	Access: read-write
MODULE-COMPLIANCE

qbDwsNetGroupInfo		1.3.6.1.4.1.4323.2.3.3.2.1
The set of all accessible objects in the DWS Network Group of this MIB.
Status: current	Access: read-write
OBJECT-GROUP

qbDwsIotGroupInfo		1.3.6.1.4.1.4323.2.3.3.2.2
The set of all accessible objects in the IOT Group of this MIB.
Status: current	Access: read-write
OBJECT-GROUP

qbDwsPktGroupInfo		1.3.6.1.4.1.4323.2.3.3.2.3
The set of all accessible objects in the Packet Group ofthis MIB.
Status: current	Access: read-write
OBJECT-GROUP

qbDwsIotAddrGroupInfo		1.3.6.1.4.1.4323.2.3.3.2.4
The set of all accessible objects in the IOT address group of this MIB.
Status: current	Access: read-write
OBJECT-GROUP