RAD-HDLC-MIB

File: RAD-HDLC-MIB.mib (61479 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC IF-MIB
RAD-MIB

Imported symbols

OBJECT-TYPE NOTIFICATION-TYPE Integer32
Gauge32 IpAddress DisplayString
RowStatus InterfaceIndex diverseIfWanGen
fileName radAtm radRouter
rtrBridge radSysRtrEvents

Defined Types

HdlcEntry  
SEQUENCE    
  hdlcProtocol INTEGER
  hdlcRateResolution INTEGER
  hdlcTxClockSource INTEGER
  hdlcTerminalMode INTEGER
  hdlcLoopbackState INTEGER
  hdlcTxClockPolarity INTEGER
  hdlcFlowControl INTEGER
  hdlcLineRate Integer32
  hdlcRxClockMode INTEGER
  hdlcLOF Gauge32
  hdlcRxClockPolarity INTEGER

HdlcCurrentEntry  
SEQUENCE    
  hdlcCurrentIfIndex Integer32
  hdlcCurrentStatus OCTET STRING
  hdlcCurrentLOF Gauge32
  hdlcCurrentInFrames Gauge32
  hdlcCurrentInErrors Gauge32
  hdlcCurrentOutFrames Gauge32
  hdlcCurrentAbortedFrames Gauge32
  hdlcCurrentLengthError Gauge32

HdlcIntervalEntry  
SEQUENCE    
  hdlcIntervalIfIndex Integer32
  hdlcIntervalNumber Integer32
  hdlcIntervalStatus OCTET STRING
  hdlcIntervalLOF Gauge32
  hdlcIntervalInFrames Gauge32
  hdlcIntervalInErrors Gauge32
  hdlcIntervalOutFrames Gauge32
  hdlcIntervalAbortedFrames Gauge32
  hdlcIntervalLengthError Gauge32

RtrIfConfigTYPE  
INTEGER other(1), ethernetLan(6), iso88023Csmacd(7), tokenRingLan(9), fddi(15), basicISDN(20), primaryISDN(21), propPointToPoint(22), slip(28), ppp(23), frameRelay(32), rs232(33), atm(37), x25ple(40), v35(45), fastEther(62), fastEtherFX(69), virtualNet(500), cod(1001), backUp(1002), dialUp(1004), b1isdn(1010), b2isdn(1011), ipBcst(1020), ipPtp(1021), ipxRaw(1022), ipxEtType(1023), ipxLlcSap(1024), ipxLlcSnap(1025), ipxPtp(1026), brgUnder(1027), wanDriver(1060), ethernetDriver(1061), tokenRingDriver(1062), fddiDriver(1064), virtualLan(1080), unknown(1100)    

RtrConfigIfEntry  
SEQUENCE    
  rtrConfigIfIndex InterfaceIndex
  rtrConfigIfType RtrIfConfigTYPE
  rtrConfigIfName DisplayString
  rtrConfigIfStatus RowStatus

RtrIfCfgEntry  
SEQUENCE    
  rtrIfCfgIndex Integer32
  rtrIfCfgIpAddress IpAddress
  rtrIfCfgRowStatus RowStatus
  rtrIfCfgIpMask IpAddress
  rtrIfCfgIfIndex Integer32
  rtrIfCfgType INTEGER
  rtrIfCfgVlanId Integer32
  rtrIfCfgMtu Integer32

RtrIpAddrEntry  
SEQUENCE    
  rtrIpAdEntAddr IpAddress
  rtrIpAdEntIfIndex Integer32
  rtrIpAdEntNetMask IpAddress
  rtrIpAdEntForwardIpBroadcast INTEGER
  rtrIpAdEntBackupAddr IpAddress
  rtrIpAdEntStatus RowStatus

RtrIcmpRdEntry  
SEQUENCE    
  rtrIcmpRdIpAddr IpAddress
  rtrIcmpRdIpAdvertAddr IpAddress
  rtrIcmpRdMaxAdvertInterval Integer32
  rtrIcmpRdMinAdvertInterval Integer32
  rtrIcmpRdAdvertLifetime Integer32
  rtrIcmpRdAdvertise INTEGER
  rtrIcmpRdPreferenceLevel Integer32
  rtrIcmpRdEntStatus Integer32

RtrRip2IfConfEntry  
SEQUENCE    
  rtrRip2IfConfAddress IpAddress
  rtrRip2IfConfVirtualDis Integer32
  rtrRip2IfConfAutoSend INTEGER
  rtrRip2IfConfRipEnable INTEGER

RtrNatIfConfEntry  
SEQUENCE    
  rtrNatIfVirtualAddress IpAddress
  rtrNatIfVirtualMask IpAddress
  rtrNatIfConfStatus RowStatus
  rtrNatIfRealAddress IpAddress
  rtrNatIfRealMask IpAddress
  rtrNatIfType INTEGER

RtrPatEntry  
SEQUENCE    
  rtrPatIdx Integer32
  rtrPatRealAddress IpAddress
  rtrPatVirtualAddress IpAddress
  rtrPatLowestPort Integer32
  rtrPatHighestPort Integer32
  rtrPatProtocol INTEGER
  rtrPatStatus RowStatus

RtrFACSActEntry  
SEQUENCE    
  rtrFACSActType INTEGER
  rtrFACSActIfIndex Integer32
  rtrFACSAction INTEGER
  rtrFACSActiveDB INTEGER

RtrFACSEntry  
SEQUENCE    
  rtrFACSIfIndex Integer32
  rtrFACSProtocolType INTEGER
  rtrFACSType INTEGER
  rtrFACSIndex Integer32
  rtrFACSSrcAdd OCTET STRING
  rtrFACSSrcAddMask OCTET STRING
  rtrFACSDesAdd OCTET STRING
  rtrFACSDesAddMask OCTET STRING
  rtrFACSOperation INTEGER
  rtrFACSNetFiltering INTEGER
  rtrFACSSocketNum Integer32
  rtrFACSMask1Id Integer32
  rtrFACSMask2Id Integer32
  rtrFACSStatus INTEGER

RtrBridgePortConfigEntry  
SEQUENCE    
  rtrBridgePortCIndex Integer32
  rtrBridgePortCIf Integer32
  rtrBridgePortCStatus RowStatus

RtrConfigEntry  
SEQUENCE    
  rtrConfigIndex Integer32
  rtrConfigDefaultGateway IpAddress
  rtrConfigArpAgingTime Integer32
  rtrConfigClassifierTosMask Integer32
  rtrConfigRIPMode INTEGER

RtrFwdEntry  
SEQUENCE    
  rtrFwdIdx Integer32
  rtrFwdIpAddress IpAddress
  rtrFwdIpMask IpAddress
  rtrFwdRuleIdx Integer32
  rtrFwdRowStatus RowStatus
  rtrFwdNextHop IpAddress
  rtrFwdIfIndex Integer32
  rtrFwdType INTEGER
  rtrFwdProto INTEGER
  rtrFwdEthQueue Integer32
  rtrFwdMetric1 Integer32

Defined Values

hdlcMibObjects 1.3.6.1.4.1.164.3.1.6.5
OBJECT IDENTIFIER    

hdlcTable 1.3.6.1.4.1.164.3.1.6.5.1
The HDLC configuration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HdlcEntry

hdlcEntry 1.3.6.1.4.1.164.3.1.6.5.1.1
Defines the contents of each line in the RAD HDLC Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HdlcEntry  

hdlcProtocol 1.3.6.1.4.1.164.3.1.6.5.1.1.1
The HDLC protocol type V35 - HDLC encapsulated over V35 X21 - HDLC encapsulated over X21 RS530 - HDLC encapsulated over RS530
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notApplicable(1), v35(2), x21(3), rs530(4)  

hdlcRateResolution 1.3.6.1.4.1.164.3.1.6.5.1.1.2
The baud rate of the internal clock.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notApplicable(1), nx56Kbps(2), nx64Kbps(3)  

hdlcTxClockSource 1.3.6.1.4.1.164.3.1.6.5.1.1.3
The baud rate of the internal clock.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER internal(1), external(2)  

hdlcTerminalMode 1.3.6.1.4.1.164.3.1.6.5.1.1.4
.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dce(1), dte(2)  

hdlcLoopbackState 1.3.6.1.4.1.164.3.1.6.5.1.1.5
internal - All data coming from the network port is looped back external - All data comming from the line is looped back.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notApplicable(1), internal(2), external(3), disable(4)  

hdlcTxClockPolarity 1.3.6.1.4.1.164.3.1.6.5.1.1.6
normal - The transmitted data is sampled at the middle of bit time inverse - The transmitted data is sampled at the end of the bit time (high data rate/long cable).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), inverse(2)  

hdlcFlowControl 1.3.6.1.4.1.164.3.1.6.5.1.1.7
Enable/Disable the CTS/RTS flow control signals.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

hdlcLineRate 1.3.6.1.4.1.164.3.1.6.5.1.1.8
The rate values for HDLC are n*56/64Kbps, where 1<=n<=32, 64, 128 and the following values: 1544, 3088, 6176. The rate values for HSSI is nMbps, where 1<=n<=52.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hdlcRxClockMode 1.3.6.1.4.1.164.3.1.6.5.1.1.9
.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notApplicable(1), internal(2), external(3)  

hdlcLOF 1.3.6.1.4.1.164.3.1.6.5.1.1.10
Total number of seconds the port is in Loss Of Frame state.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hdlcRxClockPolarity 1.3.6.1.4.1.164.3.1.6.5.1.1.11
normal - The received data is sampled at the middle of bit time inverse - The received data is sampled at the end of the bit time (high data rate/long cable).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), inverse(2)  

hdlcPerformance 1.3.6.1.4.1.164.3.1.6.5.2
OBJECT IDENTIFIER    

hdlcCurrentTable 1.3.6.1.4.1.164.3.1.6.5.2.1
The HDLC Current table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HdlcCurrentEntry

hdlcCurrentEntry 1.3.6.1.4.1.164.3.1.6.5.2.1.1
An entry in the HDLC Current table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HdlcCurrentEntry  

hdlcCurrentIfIndex 1.3.6.1.4.1.164.3.1.6.5.2.1.1.1
The index of the HDLC interface. It may be ifIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hdlcCurrentStatus 1.3.6.1.4.1.164.3.1.6.5.2.1.1.2
The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

hdlcCurrentLOF 1.3.6.1.4.1.164.3.1.6.5.2.1.1.3
The counter associated with the number of seconds the port is in Loss Of Frame state, encountered by the HDLC interface in the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hdlcCurrentInFrames 1.3.6.1.4.1.164.3.1.6.5.2.1.1.4
The counter associated with the number of received frames, encountered by the HDLC interface in the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hdlcCurrentInErrors 1.3.6.1.4.1.164.3.1.6.5.2.1.1.5
The counter associated with the number of Errored received frames, encountered by the HDLC interface in the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hdlcCurrentOutFrames 1.3.6.1.4.1.164.3.1.6.5.2.1.1.6
The counter associated with the number of transmitted frames, encountered by the HDLC interface in the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hdlcCurrentAbortedFrames 1.3.6.1.4.1.164.3.1.6.5.2.1.1.7
The counter associated with the number of frames, in which at least seven consecutive '1'-s (Abort sequence) were encountered by the HDLC interface in the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hdlcCurrentLengthError 1.3.6.1.4.1.164.3.1.6.5.2.1.1.8
The counter associated with the number of received frames with length error, encountered by the HDLC interface in the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hdlcIntervalTable 1.3.6.1.4.1.164.3.1.6.5.2.2
The HDLC Interval table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HdlcIntervalEntry

hdlcIntervalEntry 1.3.6.1.4.1.164.3.1.6.5.2.2.1
An entry in the HDLC Interval table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HdlcIntervalEntry  

hdlcIntervalIfIndex 1.3.6.1.4.1.164.3.1.6.5.2.2.1.1
The index of the HDLC interface. It may be ifIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hdlcIntervalNumber 1.3.6.1.4.1.164.3.1.6.5.2.2.1.2
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..96  

hdlcIntervalStatus 1.3.6.1.4.1.164.3.1.6.5.2.2.1.3
The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

hdlcIntervalLOF 1.3.6.1.4.1.164.3.1.6.5.2.2.1.4
The counter associated with the number of seconds the port is in Loss Of Frame state, encountered by an HDLC interface in one of the previous 96, individual 15 minute, intervals.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hdlcIntervalInFrames 1.3.6.1.4.1.164.3.1.6.5.2.2.1.5
The counter associated with the number of received frames, encountered by the HDLC interface in one of the previous 96, individual 15 minute, intervals.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hdlcIntervalInErrors 1.3.6.1.4.1.164.3.1.6.5.2.2.1.6
The counter associated with the number of Errored received frames, encountered by the HDLC interface in one of the previous 96, individual 15 minute, intervals.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hdlcIntervalOutFrames 1.3.6.1.4.1.164.3.1.6.5.2.2.1.7
The counter associated with the number of transmitted frames, encountered by the HDLC interface in one of the previous 96, individual 15 minute, intervals.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hdlcIntervalAbortedFrames 1.3.6.1.4.1.164.3.1.6.5.2.2.1.8
The counter associated with the number of frames, in which at least seven consecutive '1'-s (Abort sequence) were encountered by the HDLC interface in one of the previous 96, individual 15 minute, intervals.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hdlcIntervalLengthError 1.3.6.1.4.1.164.3.1.6.5.2.2.1.9
The counter associated with the number of received frames with length error, encountered by the HDLC interface in one of the previous 96, individual 15 minute, intervals.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

radAtmSignalingMonitor 1.3.6.1.4.1.164.12.6
OBJECT IDENTIFIER    

smSVCOperState 1.3.6.1.4.1.164.12.6.1
The SVC monitoring operational state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

smSVCAdminStatus 1.3.6.1.4.1.164.12.6.2
The SVC monitoring status.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

smILMIMode 1.3.6.1.4.1.164.12.6.3
The ILMI operational Mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), keepAliveOnly(2), enable(3)  

smILMIStatus 1.3.6.1.4.1.164.12.6.4
ILMI protocol status (VCC 0,16).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(1), up(2), disable(3)  

smUNIVersion 1.3.6.1.4.1.164.12.6.5
The UNI version that is used by both sides.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER uni3-0(1), uni3-1(2)  

smPolicing 1.3.6.1.4.1.164.12.6.6
The type of the police action performed on the cells transmitted from the user side to the network side.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), police(2), monitoring(3)  

smSAALStatus 1.3.6.1.4.1.164.12.6.7
Signaling data link (VCC 0,5) status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(1), up(2)  

smOpenedSesssions 1.3.6.1.4.1.164.12.6.8
The number of SVC sessions currently opened.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

smUserRejectedSessions 1.3.6.1.4.1.164.12.6.9
The number of sessions that the user side rejected to open.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

smNetworkRejectedSessions 1.3.6.1.4.1.164.12.6.10
The number of sessions that the Network side rejected.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

smHostRejectedSessions 1.3.6.1.4.1.164.12.6.11
The number of sessions that the device rejected to open.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

smVclILMISessionVpi 1.3.6.1.4.1.164.12.6.12
ILMI Keep alive session VPI channel. Default: 0. (VCI=16, fixed).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

rtrInterfaces 1.3.6.1.4.1.164.11.1
OBJECT IDENTIFIER    

rtrConfigIfTable 1.3.6.1.4.1.164.11.1.1
Table of configured interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtrConfigIfEntry

rtrConfigIfEntry 1.3.6.1.4.1.164.11.1.1.1
Each entry defines a configured interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  RtrConfigIfEntry  

rtrConfigIfIndex 1.3.6.1.4.1.164.11.1.1.1.1
This variable uniquely identifies the interface. It is used as a cross reference in other system tables
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

rtrConfigIfType 1.3.6.1.4.1.164.11.1.1.1.2
This variable identifies the type of the specific entry in the rtrDynamicIfConfigTable. This field is writable only at creation time (i.e., when value of status is underCreation).
Status: current Access: read-create
OBJECT-TYPE    
  RtrIfConfigTYPE  

rtrConfigIfName 1.3.6.1.4.1.164.11.1.1.1.3
This variable provides a logical name to a specific entry in rtrConfigIfTable. It is also used in identifying the Driver interfaces.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

rtrConfigIfStatus 1.3.6.1.4.1.164.11.1.1.1.4
The status of the ConfigEntry. The choices are those defined in SNMPv2-TC. Only: active, createAndWait, and destroy will be used. active - The conceptual row is available for use by the managed device. createAndWait - A new instance of a conceptual row is desired, but not to have it available for use by the managed device. destroy - Delete all instances associated with an existing conceptual row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

rtrIfCfgTable 1.3.6.1.4.1.164.11.1.2
Router Interface Configuration Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtrIfCfgEntry

rtrIfCfgEntry 1.3.6.1.4.1.164.11.1.2.1
An entry in the Router Interface Configuration Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  RtrIfCfgEntry  

rtrIfCfgIndex 1.3.6.1.4.1.164.11.1.2.1.1
This object indicates the Router Interface Index. (In some cases it will be equal to the Router Interface ifIndex).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

rtrIfCfgIpAddress 1.3.6.1.4.1.164.11.1.2.1.2
IP Address of the Router Interface.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

rtrIfCfgRowStatus 1.3.6.1.4.1.164.11.1.2.1.3
This object enables the user to create/delete entries of this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

rtrIfCfgIpMask 1.3.6.1.4.1.164.11.1.2.1.4
IP Mask Address Router Interface.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

rtrIfCfgIfIndex 1.3.6.1.4.1.164.11.1.2.1.5
ifIndex of the device interface connected to this Router Interface.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

rtrIfCfgType 1.3.6.1.4.1.164.11.1.2.1.6
The Router Interface Type. atm - ATM router interface lis - Logical IP Subnet router interface. ethernet - Ethernet router interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER notApplicable(1), atm(2), lis(3), ethernet(4)  

rtrIfCfgVlanId 1.3.6.1.4.1.164.11.1.2.1.7
The VLAN ID assigned to Tagged frames transmitted from this Router Interface. The value inserted should be a defined VLAN.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

rtrIfCfgMtu 1.3.6.1.4.1.164.11.1.2.1.8
The size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

ipSpec 1.3.6.1.4.1.164.11.2
OBJECT IDENTIFIER    

rtrIpAddrTable 1.3.6.1.4.1.164.11.2.1
This table is parralel to MIB II IpAddrTable, and is used to add/delete entries to/from that table. In addition it contains private objects.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtrIpAddrEntry

rtrIpAddrEntry 1.3.6.1.4.1.164.11.2.1.1
The addressing information for one of this entity's IP addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  RtrIpAddrEntry  

rtrIpAdEntAddr 1.3.6.1.4.1.164.11.2.1.1.1
The IP address to which this entry's addressing information pertains.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

rtrIpAdEntIfIndex 1.3.6.1.4.1.164.11.2.1.1.2
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

rtrIpAdEntNetMask 1.3.6.1.4.1.164.11.2.1.1.3
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

rtrIpAdEntForwardIpBroadcast 1.3.6.1.4.1.164.11.2.1.1.4
This variable controls forwarding of IP (sub)net-directed broadcasts destined for an attached sub(net).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rtrIpAdEntBackupAddr 1.3.6.1.4.1.164.11.2.1.1.5
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

rtrIpAdEntStatus 1.3.6.1.4.1.164.11.2.1.1.6
The Status variable is used to create and destroy a Ip Addresses.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

icmpSpec 1.3.6.1.4.1.164.11.2.2
OBJECT IDENTIFIER    

rtrIcmpGenErrMsgEnable 1.3.6.1.4.1.164.11.2.2.1
This variable controlls the ability to generate ICMP error messages
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rtrIcmpRdTable 1.3.6.1.4.1.164.11.2.2.2
This table contains ICMP Router Discovery parameters configurated per IP interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtrIcmpRdEntry

rtrIcmpRdEntry 1.3.6.1.4.1.164.11.2.2.2.1
The ICMP parameters configurated for IP interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  RtrIcmpRdEntry  

rtrIcmpRdIpAddr 1.3.6.1.4.1.164.11.2.2.2.1.1
The IP address to which this entry's information pertains.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

rtrIcmpRdIpAdvertAddr 1.3.6.1.4.1.164.11.2.2.2.1.2
The IP destination address to be used for multicast Router Advertisements sent from the interface. The only permissible values are the all-systems multicast address, 224.0.0.1, or the limited-broadcast address, 255.255.255.255.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

rtrIcmpRdMaxAdvertInterval 1.3.6.1.4.1.164.11.2.2.2.1.3
The maximum time allowed between sending multicast Router Advertisements from the interface, in seconds. Must be no less than 4 seconds and no greater than 1800 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..1800  

rtrIcmpRdMinAdvertInterval 1.3.6.1.4.1.164.11.2.2.2.1.4
The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface, in seconds. Must be no less than 3 seconds and no greater than rtrIcmpRdMaxAdvertInterval. Default: 0.75 * rtrIcmpRdMaxAdvertInterval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..1800  

rtrIcmpRdAdvertLifetime 1.3.6.1.4.1.164.11.2.2.2.1.5
The maximum length of time that the advertised addresses are to be considered as valid. Must be no less than rtrIcmpRdMaxAdvertInterval and no greater than 9000 seconds. Default: 3 * rtrIcmpRdMaxAdvertInterval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..9000  

rtrIcmpRdAdvertise 1.3.6.1.4.1.164.11.2.2.2.1.6
A flag indicating whether or not the address is to be advertised.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rtrIcmpRdPreferenceLevel 1.3.6.1.4.1.164.11.2.2.2.1.7
The preferability of the address as a default router address, relative to other router addresses on the same subnet.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

rtrIcmpRdEntStatus 1.3.6.1.4.1.164.11.2.2.2.1.8
Setting of any value to this object set values of all fields to the default values.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

rip2Spec 1.3.6.1.4.1.164.11.2.3
OBJECT IDENTIFIER    

rtrRip2IfConfTable 1.3.6.1.4.1.164.11.2.3.1
This table is an extension of rip2IfConfTable (RFC 1724 ,RIP 2). It means that every time somebody creates/destroys a row in the rip2IfConfTable, the same row should be automatically created/destroyed in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtrRip2IfConfEntry

rtrRip2IfConfEntry 1.3.6.1.4.1.164.11.2.3.1.1
An entry in table rtrRip2IfConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  RtrRip2IfConfEntry  

rtrRip2IfConfAddress 1.3.6.1.4.1.164.11.2.3.1.1.1
The IP Address of this system on the indicated subnet. For unnumbered interfaces, the value 0.0.0.N, where the least significant 24 bits (N) is the ifIndex for the IP Interface in network byte order
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

rtrRip2IfConfVirtualDis 1.3.6.1.4.1.164.11.2.3.1.1.2
This variable defines the virtual number of hops assigned to the interface specified by rtrIfIpAddrIndex. This enables fine-tuning of the RIP routing algorithm.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

rtrRip2IfConfAutoSend 1.3.6.1.4.1.164.11.2.3.1.1.3
When set to enable only the default route is sent through the interface. When set to disable, regular RIPs are sent.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rtrRip2IfConfRipEnable 1.3.6.1.4.1.164.11.2.3.1.1.4
This object shows whether RIP Protocol is enabled on the current interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER no(2), yes(3)  

arpSpec 1.3.6.1.4.1.164.11.2.4
OBJECT IDENTIFIER    

rtrArpDeleteTable 1.3.6.1.4.1.164.11.2.4.1
Setting this object to any not-null value has the effect of deleting all entries of the ARP table.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

rtrArpInactiveTimeOut 1.3.6.1.4.1.164.11.2.4.2
This variable defines the maximum time period (in second) that can pass between ARP requests concerning an entry in the ARP table. After this time period, the entry is deleted from the table.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

rtrArpProxy 1.3.6.1.4.1.164.11.2.4.3
When ARP Proxy is enabled, the router can respond to ARP requests for nodes located on a different sub-net, provided they are it its network table. The router responds with its own MAC address. When ARP Proxy is disabled, the router responds only to ARP requests for its own IP addresses.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rtrNat 1.3.6.1.4.1.164.11.2.5
OBJECT IDENTIFIER    

rtrNatIfConfTable 1.3.6.1.4.1.164.11.2.5.1
A list of interfaces which require separate NAT configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtrNatIfConfEntry

rtrNatIfConfEntry 1.3.6.1.4.1.164.11.2.5.1.1
A single routing domain in a single subnet.
Status: current Access: not-accessible
OBJECT-TYPE    
  RtrNatIfConfEntry  

rtrNatIfVirtualAddress 1.3.6.1.4.1.164.11.2.5.1.1.1
The IP Address of the virtual subnet to be translated by the 'NAT box' attached to this interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

rtrNatIfVirtualMask 1.3.6.1.4.1.164.11.2.5.1.1.2
The subnet Mask of the virtual subnet.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

rtrNatIfConfStatus 1.3.6.1.4.1.164.11.2.5.1.1.3
Writing 'destroy' has the effect of deleting this interface.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

rtrNatIfRealAddress 1.3.6.1.4.1.164.11.2.5.1.1.4
The IP Address of the real subnet which is used by 'NAT box' for translation.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

rtrNatIfRealMask 1.3.6.1.4.1.164.11.2.5.1.1.5
The subnet Mask of the real subnet.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

rtrNatIfType 1.3.6.1.4.1.164.11.2.5.1.1.6
NAT type. static - Translate a specific virtual IP network to a specific real IP network. TCP, UDP and ICMP sessions originated both in real and virtual networks will be translated. dynamic - (Concurrent) Translate real IP network to larger or equal virtual IP network. TCP, UDP and ICMP sessions originated in virtual networks only can be translated and sessions originated in real networks will be rejected. A session that starts in the NAT system will be active until there will be no traffic for aging timeout period. pat - (Port Address Translation/ Single IP). Translate one real IP address to virtual IP network. TCP, UDP and ICMP sessions originated in virtual network only can be translated, sessions originated in real network will be rejected. A session that starts in the NAT system will be active until there will be no traffic for aging timeout period. transparent - In transparent mode all frames belonging to the defined IP network will be forwarded with no translation: virtual = real.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER static(1), dynamic(2), pat(3), transparent(4)  

rtrPatTable 1.3.6.1.4.1.164.11.2.5.2
Port Address Translation (PAT - single IP NAT) configuration Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtrPatEntry

rtrPatEntry 1.3.6.1.4.1.164.11.2.5.2.1
Each entry describe unique mapping between real IP address, range of ports and protocol, to local (virtual) IP address. Ports are used in the TCP (rfc793) to name the ends of logical connections which carry long term conversations. For the purpose of providing services to unknown callers, a service contact port is defined.
Status: current Access: not-accessible
OBJECT-TYPE    
  RtrPatEntry  

rtrPatIdx 1.3.6.1.4.1.164.11.2.5.2.1.1
Running index for PAT table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..8  

rtrPatRealAddress 1.3.6.1.4.1.164.11.2.5.2.1.2
The real IP Address used for translation
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

rtrPatVirtualAddress 1.3.6.1.4.1.164.11.2.5.2.1.3
The virtual IP Address used for translation
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

rtrPatLowestPort 1.3.6.1.4.1.164.11.2.5.2.1.4
Lowest Port number for this PAT entry
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

rtrPatHighestPort 1.3.6.1.4.1.164.11.2.5.2.1.5
Highest Port number for this PAT entry
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

rtrPatProtocol 1.3.6.1.4.1.164.11.2.5.2.1.6
Protocol selected. This Protocol and port range (lowest port - highest port) define the application (FTP, Telnet, SMTP etc.). Protocol enumaration numbers correspond to IP header 'protocol' field
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tcp(6), udp(17)  

rtrPatStatus 1.3.6.1.4.1.164.11.2.5.2.1.7
This object enables creating and deleting entries of the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

rtrFACS 1.3.6.1.4.1.164.11.5
OBJECT IDENTIFIER    

rtrFACSDefaultAction 1.3.6.1.4.1.164.11.5.1
Used to define the default action for the device, when no FACS statements applicable to a given frame are defined.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER block(1), forward(2), blockAndReport(129)  

rtrFACSActTable 1.3.6.1.4.1.164.11.5.2
The table of FACS action.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtrFACSActEntry

rtrFACSActEntry 1.3.6.1.4.1.164.11.5.2.1
Each rtrFACSActEntry consist of the following parameters
Status: current Access: not-accessible
OBJECT-TYPE    
  RtrFACSActEntry  

rtrFACSActType 1.3.6.1.4.1.164.11.5.2.1.1
This parameter indicates on which FACS Table the FACS action will preform.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER tx(1), rx(2)  

rtrFACSActIfIndex 1.3.6.1.4.1.164.11.5.2.1.2
The interface to which this FACS entry is applicable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

rtrFACSAction 1.3.6.1.4.1.164.11.5.2.1.3
The management station that sends a SET request for one of these actions with indexes rtrFACSType and rtrFACSIfIndex defines the type and the interface Id for which all FACS statements are to be erased. If no interface or no type is specified, all FACS statements for a protocol are erased.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), eraseIP(2), eraseDECnet(3), eraseIPX(4), eraseBrg(5), replaceIP(6), replaceIPX(8), replaceBrg(9), backupIP(10), backupIPX(12), backupBrg(13)  

rtrFACSActiveDB 1.3.6.1.4.1.164.11.5.2.1.4
This parameter will point on which Facs DataBase the SNMP agent read. The Active dataBase is Read Only. The user may change FACS statements in the temporary DataBase and then write it to the Active DB.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER active(1), temporary(2)  

rtrFACSTable 1.3.6.1.4.1.164.11.5.3
The table of FACS statment.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtrFACSEntry

rtrFACSEntry 1.3.6.1.4.1.164.11.5.3.1
Each FACS statment consists of the following parameters
Status: current Access: not-accessible
OBJECT-TYPE    
  RtrFACSEntry  

rtrFACSIfIndex 1.3.6.1.4.1.164.11.5.3.1.1
The interface to which this FACS entry is applicable. For applications this variables is always 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

rtrFACSProtocolType 1.3.6.1.4.1.164.11.5.3.1.2
This parameter define the protocol the Security Access Control is applicable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ip(1), ipx(2), dec(3), bridge(4)  

rtrFACSType 1.3.6.1.4.1.164.11.5.3.1.3
The Mode of in which this FACS statement operates. For applications this variable is always rx(2).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER tx(1), rx(2), cod(3)  

rtrFACSIndex 1.3.6.1.4.1.164.11.5.3.1.4
Index to the FACS Table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

rtrFACSSrcAdd 1.3.6.1.4.1.164.11.5.3.1.5
The size of the octet string will be according to the protocol type defined in rtrFACSProtocolType.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

rtrFACSSrcAddMask 1.3.6.1.4.1.164.11.5.3.1.6
Source-address mask .
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

rtrFACSDesAdd 1.3.6.1.4.1.164.11.5.3.1.7
Destination-address The size of the octet string will be according to the protocol type define in rtrFACSProtocolType .
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

rtrFACSDesAddMask 1.3.6.1.4.1.164.11.5.3.1.8
Destination-address mask .
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

rtrFACSOperation 1.3.6.1.4.1.164.11.5.3.1.9
... .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER block(1), forward(2), permit(3), deny(4), blockAndReport(129)  

rtrFACSNetFiltering 1.3.6.1.4.1.164.11.5.3.1.10
... .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), l2multicast(2), arp(3), icmp(4), ip(5), udp(6), tcp(7), decnet(8), ipx(9)  

rtrFACSSocketNum 1.3.6.1.4.1.164.11.5.3.1.11
Port/socket number for different applications 0 is default meaning not applicable. none(1), ftp(21), telnet(23), smtp(25), tftp(69), snmp(161), snmpTrap(162), rip(520), sapIPX(1106), ripIPX(1107)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

rtrFACSMask1Id 1.3.6.1.4.1.164.11.5.3.1.12
Index into RND mask table FACS/COD Type) .
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

rtrFACSMask2Id 1.3.6.1.4.1.164.11.5.3.1.13
Index into RND mask table FACS/COD according to the value of rtrFACSType .
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

rtrFACSStatus 1.3.6.1.4.1.164.11.5.3.1.14
The status of a table entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), createRequest(2), underCreation(3), invalid(4)  

rtrFACSFrameData 1.3.6.1.4.1.164.11.5.4
Data from the frame that violated a FACS Filter.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

rtrBridgePortConfigTable 1.3.6.1.4.1.164.11.7.1
Table of the bridge ports
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtrBridgePortConfigEntry

rtrBridgePortConfigEntry 1.3.6.1.4.1.164.11.7.1.1
Each entry defines a bridge port
Status: current Access: not-accessible
OBJECT-TYPE    
  RtrBridgePortConfigEntry  

rtrBridgePortCIndex 1.3.6.1.4.1.164.11.7.1.1.1
This is the index of the bridge port. It is the same as 'dot1dBasePort' of the Bridge MIB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

rtrBridgePortCIf 1.3.6.1.4.1.164.11.7.1.1.2
The config ifIndex the bridge port is sitting on.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

rtrBridgePortCStatus 1.3.6.1.4.1.164.11.7.1.1.3
The status of the RtrBridgePortConfigEntry. Creating and destroying the bridge port is done by this variable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

radRouterConfig 1.3.6.1.4.1.164.11.9
OBJECT IDENTIFIER    

rtrConfigTable 1.3.6.1.4.1.164.11.9.1
The Router's Configuration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtrConfigEntry

rtrConfigEntry 1.3.6.1.4.1.164.11.9.1.1
An entry in the Router's Configuration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  RtrConfigEntry  

rtrConfigIndex 1.3.6.1.4.1.164.11.9.1.1.1
This object indicates the Router's Index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

rtrConfigDefaultGateway 1.3.6.1.4.1.164.11.9.1.1.2
Router Default Gateway.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

rtrConfigArpAgingTime 1.3.6.1.4.1.164.11.9.1.1.3
ARP Aging Time.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

rtrConfigClassifierTosMask 1.3.6.1.4.1.164.11.9.1.1.5
This object indicates the Classifier's TOS Mask, as follows: 0x1C for DTR -- rfc795 0x1E for Cisco 0xE0 for Precedence -- rfc795 0xFC for Diffserv Else for Manual .
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

rtrConfigRIPMode 1.3.6.1.4.1.164.11.9.1.1.6
This object determines the Router Information Protocol to measure the shortest path between 2 positions on the network.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notApplicable(1), rip1(2), rip2(3), rip1And2(4)  

rtrFwdTable 1.3.6.1.4.1.164.11.9.3
The Router's Forwarding Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtrFwdEntry

rtrFwdEntry 1.3.6.1.4.1.164.11.9.3.1
An entry in the Router's Forwarding table.
Status: current Access: not-accessible
OBJECT-TYPE    
  RtrFwdEntry  

rtrFwdIdx 1.3.6.1.4.1.164.11.9.3.1.1
This object indicates the Router Index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

rtrFwdIpAddress 1.3.6.1.4.1.164.11.9.3.1.2
This object indicates the Destination IP Address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

rtrFwdIpMask 1.3.6.1.4.1.164.11.9.3.1.3
This object indicates the Mask IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

rtrFwdRuleIdx 1.3.6.1.4.1.164.11.9.3.1.4
This object indicates the Rule's Number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

rtrFwdRowStatus 1.3.6.1.4.1.164.11.9.3.1.5
This object enables the user to create/delete entries in this table. Entry of Type rtrFwdType = staticRouting(3) are created by the user. Only this type of entries can be deleted by the user. Entry of Type rtrFwdType = interface(2) are created/deleted automatically by the Agent when the user creates/deletes an interface of the Router.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

rtrFwdNextHop 1.3.6.1.4.1.164.11.9.3.1.6
This object indicates the IP Address of the Next Hop.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

rtrFwdIfIndex 1.3.6.1.4.1.164.11.9.3.1.7
This object indicates the Interface Index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

rtrFwdType 1.3.6.1.4.1.164.11.9.3.1.8
The type of route. Note that local(3) refers to a route for which the next hop is the final destination; remote(4) refers to a route for which the next hop is not the final destina- tion. Routes which do not result in traffic forwarding or rejection should not be displayed even if the implementation keeps them stored internally. reject (2) refers to a route which, if matched, discards the message as unreachable. This is used in some protocols as a means of correctly aggregating routes.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), reject(2), local(3), remote(4)  

rtrFwdProto 1.3.6.1.4.1.164.11.9.3.1.9
The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), local(2), netmgmt(3), rip(8), lis(41)  

rtrFwdEthQueue 1.3.6.1.4.1.164.11.9.3.1.10
This object indicates the ETH Queue number.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

rtrFwdMetric1 1.3.6.1.4.1.164.11.9.3.1.11
The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's rtrFwdProto value. If this metric is not used, its value should be set to -1.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

rtrFACSViolation 1.3.6.1.4.1.164.6.1.11.0.1
The trap is sent for every violation of a FACS filter.
Status: current Access: read-create
NOTIFICATION-TYPE    

rtrSwDwnLoadTrap 1.3.6.1.4.1.164.6.1.11.0.2
The trap is sent after the tftp download of the software and before the decompression and reset operations.
Status: current Access: read-create
NOTIFICATION-TYPE