RADLAN-rlInterfaces

File: RADLAN-rlInterfaces.mib (34730 bytes)

Imported modules

RADLAN-MIB	IF-MIB	Q-BRIDGE-MIB
SNMPv2-TC-v1	SNMPv2-SMI	SNMPv2-TC

Imported symbols

swInterfaces	rlIfInterfaces	ifIndex
PortList	DisplayString	Unsigned32
Integer32	Counter32	MODULE-IDENTITY
OBJECT-TYPE	RowStatus	TruthValue
TEXTUAL-CONVENTION

Defined Types

AutoNegCapabilitiesBits
Auto negotiation capabilities bits.
TEXTUAL-CONVENTION
	BITS	default(0), unknown(1), tenHalf(2), tenFull(3), fastHalf(4), fastFull(5), gigaHalf(6), gigaFull(7)

SwIfEntry
SEQUENCE
	swIfIndex	INTEGER
	swIfPhysAddressType	INTEGER
	swIfDuplexAdminMode	INTEGER
	swIfDuplexOperMode	INTEGER
	swIfBackPressureMode	INTEGER
	swIfTaggedMode	INTEGER
	swIfTransceiverType	INTEGER
	swIfLockAdminStatus	INTEGER
	swIfLockOperStatus	INTEGER
	swIfType	INTEGER
	swIfDefaultTag	INTEGER
	swIfDefaultPriority	INTEGER
	swIfStatus	RowStatus
	swIfFlowControlMode	INTEGER
	swIfSpeedAdminMode	INTEGER
	swIfSpeedDuplexAutoNegotiation	INTEGER
	swIfOperFlowControlMode	INTEGER
	swIfOperSpeedDuplexAutoNegotiation	INTEGER
	swIfOperBackPressureMode	INTEGER
	swIfAdminLockAction	INTEGER
	swIfOperLockAction	INTEGER
	swIfAdminLockTrapEnable	TruthValue
	swIfOperLockTrapEnable	TruthValue
	swIfOperSuspendedStatus	TruthValue
	swIfLockOperTrapCount	INTEGER
	swIfLockAdminTrapFrequency	INTEGER
	swIfReActivate	TruthValue
	swIfAdminMdix	INTEGER
	swIfOperMdix	INTEGER
	swIfHostMode	INTEGER
	swIfSingleHostViolationAdminAction	INTEGER
	swIfSingleHostViolationOperAction	INTEGER
	swIfSingleHostViolationAdminTrapEnable	TruthValue
	swIfSingleHostViolationOperTrapEnable	TruthValue
	swIfSingleHostViolationOperTrapCount	INTEGER
	swIfSingleHostViolationAdminTrapFrequency	INTEGER
	swIfLockLimitationMode	INTEGER
	swIfLockMaxMacAddresses	INTEGER
	swIfLockMacAddressesCount	INTEGER
	swIfAdminSpeedDuplexAutoNegotiationLocalCapabilities	AutoNegCapabilitiesBits
	swIfOperSpeedDuplexAutoNegotiationLocalCapabilities	AutoNegCapabilitiesBits
	swIfSpeedDuplexNegotiationRemoteCapabilities	AutoNegCapabilitiesBits
	swIfAdminComboMode	INTEGER
	swIfOperComboMode	INTEGER

SwIfPortLockIfRangeEntry
SEQUENCE
	swIfPortLockIfRangeIndex	INTEGER
	swIfPortLockIfRange	PortList
	swIfPortLockIfRangeLockStatus	INTEGER
	swIfPortLockIfRangeAction	INTEGER
	swIfPortLockIfRangeTrapEn	TruthValue
	swIfPortLockIfRangeTrapFreq	INTEGER

SwIfExtEntry
SEQUENCE
	swIfExtSFPSpeed	INTEGER

Defined Values

swIfTable		1.3.6.1.4.1.89.43.1
Switch media specific information and configuration of the device interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwIfEntry

swIfEntry		1.3.6.1.4.1.89.43.1.1
Defines the contents of each line in the swIfTable table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwIfEntry

swIfIndex		1.3.6.1.4.1.89.43.1.1.1
Index to the swIfTable. The interface defined by a particular value of this index is the same interface as identified by the same value of ifIndex (MIB II).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swIfPhysAddressType		1.3.6.1.4.1.89.43.1.1.2
This variable indicates whether the physical address assigned to this interface should be the default one or be chosen from the set of reserved physical addresses of the device.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	default(1), reserve(2)

swIfDuplexAdminMode		1.3.6.1.4.1.89.43.1.1.3
This variable specifies whether this interface should operate in half duplex or full duplex mode. This specification will take effect only if swIfSpeedDuplexAutoNegotiation is disabled. A value of 'none' is returned if a value of the variable hasn't been set.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), half(2), full(3)

swIfDuplexOperMode		1.3.6.1.4.1.89.43.1.1.4
This variable indicates whether this interface operates in half duplex or full duplex mode. This variable can have the values hybrid or unknown only for a trunk. unknown - only if trunk operative status is not present.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	half(1), full(2), hybrid(3), unknown(4)

swIfBackPressureMode		1.3.6.1.4.1.89.43.1.1.5
This variable indicates whether this interface activates back pressure when congested.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

swIfTaggedMode		1.3.6.1.4.1.89.43.1.1.6
If enable, this interface operates in tagged mode, i.e all frames sent out through this interface will have the 802.1Q header. If disabled the frames will not be tagged.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

swIfTransceiverType		1.3.6.1.4.1.89.43.1.1.7
This variable indicates the transceiver type of this interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	regular(1), fiberOptics(2), comboRegular(3), comboFiberOptics(4)

swIfLockAdminStatus		1.3.6.1.4.1.89.43.1.1.8
This variable indicates whether this interface should operate in locked or unlocked mode. In unlocked mode the device learns all MAC addresses from this port and forwards all frames arrived at this port. In locked mode no new MAC addresses are learned and only frames with known source MAC addresses are forwarded.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	locked(1), unlocked(2)

swIfLockOperStatus		1.3.6.1.4.1.89.43.1.1.9
This variable defines whether this interface operates in locked or unlocked mode. It is locked in each of the following two cases: 1) if swLockAdminStatus is set to locked 2) no IP/IPX interface is defined over this interface and no VLAN contains this interface. In unlocked mode the device learns all MAC addresses from this port and forwards all frames arrived at this port. In locked mode no new MAC addresses are learned and only frames with known source MAC addresses are forwarded.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	locked(1), unlocked(2)

swIfType		1.3.6.1.4.1.89.43.1.1.10
This variable specifies the type of interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eth10M(1), eth100M(2), eth1000M(3), eth10G(4), unknown(5)

swIfDefaultTag		1.3.6.1.4.1.89.43.1.1.11
This variable specifies the default VLAN tag which will be attached to outgoing frames if swIfTaggedMode for this interface is enabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

swIfDefaultPriority		1.3.6.1.4.1.89.43.1.1.12
This variable specifies the default port priority.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

swIfStatus		1.3.6.1.4.1.89.43.1.1.13
The status of a table entry. It is used to delete an entry from this table.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

swIfFlowControlMode		1.3.6.1.4.1.89.43.1.1.14
on - Flow control will be enabled on this interface according to the IEEE 802.3x standard. off - Flow control is disabled. autoNegotiation - Flow control will be enabled or disabled on this interface. If enabled, it will operate as specified by the IEEE 802.3x standard. enabledRx - Flow control will be enabled on this interface for recieved frames. enabledTx - Flow control will be enabled on this interface for transmitted frames. An attempt to set this object to 'enabledRx(4)' or 'enabledTx(5)' will fail on interfaces that do not support operation at greater than 100 Mb/s. In any case, flow control can work only if swIfDuplexOperMode is full.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), autoNegotiation(3), enabledRx(4), enabledTx(5)

swIfSpeedAdminMode		1.3.6.1.4.1.89.43.1.1.15
This variable specifies the required speed of this interface in bits per second. This specification will take effect only if swIfSpeedDuplexAutoNegotiation is disabled. A value of 10 is returned for 10G. A value of 0 is returned if the value of the variable hasn't been set.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

swIfSpeedDuplexAutoNegotiation		1.3.6.1.4.1.89.43.1.1.16
If enabled the speed and duplex mode will be set by the device through the autonegotiation process. Otherwise these characteristics will be set according to the values of swIfSpeedAdminMode and swIfSpeedDuplexAutoNegotiation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swIfOperFlowControlMode		1.3.6.1.4.1.89.43.1.1.17
on - Flow control is enabled on this interface according to the IEEE 802.3x standard. off - Flow control is disabled. enabledRx - Flow control is enabled on this interface for recieved frames. enabledTx - Flow control is enabled on this interface for transmitted frames.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), enabledRx(3), enabledTx(4)

swIfOperSpeedDuplexAutoNegotiation		1.3.6.1.4.1.89.43.1.1.18
If enabled the speed and duplex are determined by the device through the autonegotiation process. If disabled these characteristics are determined according to the values of swIfSpeedAdminMode and swIfDuplexAdminMode. hybrid - only for a trunk. unknown - only for ports that there operative status is not present.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2), hybrid(3), unknown(4)

swIfOperBackPressureMode		1.3.6.1.4.1.89.43.1.1.19
This variable indicates the operative back pressure mode of this interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enable(1), disable(2), hybrid(3), unknown(4)

swIfAdminLockAction		1.3.6.1.4.1.89.43.1.1.20
This variable indicates which action this interface should be taken in locked mode and therefore relevant only in locked mode. Possible actions: discard(1) - every packet is dropped. forwardNormal(2) - every packet is forwarded according to the DST address. discardDisable(3) - drops the first packet and suspends the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	discard(1), forwardNormal(2), discardDisable(3)

swIfOperLockAction		1.3.6.1.4.1.89.43.1.1.21
This variable indicates which action this interface actually takes in locked mode and therefore relevant only in locked mode. Possible actions: discard(1) - every packet is dropped. forwardNormal(2) - every packet is forwarded according to the DST address. discardDisable(3) - drops the first packet and suspends the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	discard(1), forwardNormal(2), discardDisable(3)

swIfAdminLockTrapEnable		1.3.6.1.4.1.89.43.1.1.22
This variable indicates whether to create a SNMP trap in the locked mode.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

swIfOperLockTrapEnable		1.3.6.1.4.1.89.43.1.1.23
This variable indicates whether a SNMP trap can be created in the locked mode.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

swIfOperSuspendedStatus		1.3.6.1.4.1.89.43.1.1.24
This variable indicates whether the port is suspended or not due to some feature. After reboot this value is false
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

swIfLockOperTrapCount		1.3.6.1.4.1.89.43.1.1.25
This variable indicates the trap counter status per ifIndex (i.e. number of received packets since the last trap sent due to a packet which was received on this ifIndex). It's relevant only in locked mode while trap is enabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..2147483647

swIfLockAdminTrapFrequency		1.3.6.1.4.1.89.43.1.1.26
This variable indicates the minimal frequency (in seconds) of sending a trap per ifIndex. It's relevant only in locked mode and in trap enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..1000000

swIfReActivate		1.3.6.1.4.1.89.43.1.1.27
This variable reactivates (enables) an ifIndex (which was suspended)
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

swIfAdminMdix		1.3.6.1.4.1.89.43.1.1.28
The configuration is on a physical port, not include trunks. cross - The interface should force crossover. normal - The interface should not force crossover. auto - Auto mdix is enabled on the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	cross(1), normal(2), auto(3)

swIfOperMdix		1.3.6.1.4.1.89.43.1.1.29
cross - The interface is in crossover mode. normal - The interface is not in crossover mode. unknown - Only for port that its operative status is not present or down.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cross(1), normal(2), unknown(3)

swIfHostMode		1.3.6.1.4.1.89.43.1.1.30
This variable indicates the 802.1X host mode of a port. Relevant when the port's 802.1X control is auto
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	single(1), multiple(2)

swIfSingleHostViolationAdminAction		1.3.6.1.4.1.89.43.1.1.31
This variable indicates which action this interface should take in single authorized. Possible actions: discard - every packet is dropped. forwardNormal - every packet is forwarded according to the DST address. discardDisable - drops the first packet and suspends the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	discard(1), forwardNormal(2), discardDisable(3)

swIfSingleHostViolationOperAction		1.3.6.1.4.1.89.43.1.1.32
This variable indicates which action this interface actually takes in single authorized. Possible actions: discard(1) - every packet is dropped. forwardNormal(2) - every packet is forwarded according to the DST address. discardDisable(3) - drops the first packet and suspends the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	discard(1), forwardNormal(2), discardDisable(3)

swIfSingleHostViolationAdminTrapEnable		1.3.6.1.4.1.89.43.1.1.33
This variable indicates whether to create a SNMP trap in single authorized.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

swIfSingleHostViolationOperTrapEnable		1.3.6.1.4.1.89.43.1.1.34
This variable indicates whether a SNMP trap can be created in the single authorized.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

swIfSingleHostViolationOperTrapCount		1.3.6.1.4.1.89.43.1.1.35
This variable indicates the trap counter status per ifIndex (i.e. number of received packets since the last trap sent due to a packet which was received on this ifIndex). It's relevant only in single authorized while trap is enabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..2147483647

swIfSingleHostViolationAdminTrapFrequency		1.3.6.1.4.1.89.43.1.1.36
This variable indicates the minimal frequency (in seconds) of sending a trap per ifIndex. It's relevant only in single authorized and in trap enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..1000000

swIfLockLimitationMode		1.3.6.1.4.1.89.43.1.1.37
This variable indicates what is the learning limitation on the locked interface. Possible values: disabled - learning is stopped. The dynamic addresses associated with the port are not aged out or relearned on other port as long as the port is locked. dynamic - dynamic addresses can be learned up to the maximum dynamic addresses allowed on the port. Relearning and aging of the dynamic addresses are enabled. The learned addresses aren't kept after reset.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), dynamic(2)

swIfLockMaxMacAddresses		1.3.6.1.4.1.89.43.1.1.38
This variable defines the maximum number of dynamic addresses that can be asscoiated with the locked interface. It isn't relevant in disabled limitation mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..2147483647

swIfLockMacAddressesCount		1.3.6.1.4.1.89.43.1.1.39
This variable indicates the actual number of dynamic addresses that can be asscoiated with the locked interface. It isn't relevant in disabled limitation mode.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..2147483647

swIfAdminSpeedDuplexAutoNegotiationLocalCapabilities		0.1.3.6.1.4.1.89.43.1.1.40
Administrative auto negotiation capabilities of the interface that can be advertised when swIfSpeedDuplexAutoNegotiation is enabled. default bit means advertise all the port's capabilities according to its type.
Status: current	Access: read-write
OBJECT-TYPE
	AutoNegCapabilitiesBits

swIfOperSpeedDuplexAutoNegotiationLocalCapabilities		1.3.6.1.4.1.89.43.1.1.41
Operative auto negotiation capabilities of the remote link. unknown bit means that port operative status is not up.
Status: current	Access: read-only
OBJECT-TYPE
	AutoNegCapabilitiesBits

swIfSpeedDuplexNegotiationRemoteCapabilities		1.3.6.1.4.1.89.43.1.1.42
Operative auto negotiation capabilities of the remote link. unknown bit means that port operative status is not up, or auto negotiation process not complete, or remote link is not auto negotiation able.
Status: current	Access: read-only
OBJECT-TYPE
	AutoNegCapabilitiesBits

swIfAdminComboMode		1.3.6.1.4.1.89.43.1.1.43
This variable specifies the administrative mode of a combo Ethernet interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	force-fiber(1), force-copper(2), prefer-fiber(3), prefer-copper(4)

swIfOperComboMode		1.3.6.1.4.1.89.43.1.1.44
This variable specifies the operative mode of a combo Ethernet interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	fiber(1), copper(2), unknown(3)

swIfMibVersion		1.3.6.1.4.1.89.43.2
The swIfTable Mib's version, the current version is 3.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swIfPortLockSupport		1.3.6.1.4.1.89.43.3
indicates if the locked port package is supported.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	supported(1), notSupported(2)

swIfPortLockActionSupport		1.3.6.1.4.1.89.43.4
indicates which port lock actions are supported: (bit 0 is the most significant bit) bit 0 - discard bit 1 - forwardNormal bit 2 - discardDisable
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

swIfPortLockTrapSupport		1.3.6.1.4.1.89.43.5
indicates with which port lock actions the trap option is supported (e.g. discard indicates that trap is supported only when the portlock action is discard): (bit 0 is the most significant bit) bit 0 - discard bit 1 - forwardNormal bit 2 - discardDisable
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

swIfPortLockIfRangeTable		1.3.6.1.4.1.89.43.6
Port lock interfaces range configuration
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwIfPortLockIfRangeEntry

swIfPortLockIfRangeEntry		1.3.6.1.4.1.89.43.6.1
Defines the contents of each line in the swIfPortLockIfRangeTable table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwIfPortLockIfRangeEntry

swIfPortLockIfRangeIndex		1.3.6.1.4.1.89.43.6.1.1
Index to the swIfPortLockIfRangeTable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swIfPortLockIfRange		1.3.6.1.4.1.89.43.6.1.2
The set of interfaces to which the port lock parameters should be configured
Status: current	Access: read-write
OBJECT-TYPE
	PortList

swIfPortLockIfRangeLockStatus		1.3.6.1.4.1.89.43.6.1.3
This variable indicates whether the interfaces range should operate in locked or unlocked mode. In unlocked mode the device learns all MAC addresses from these interfaces and forwards all frames arrived at these interfaces. In locked mode no new MAC addresses are learned and only frames with known source MAC addresses are forwarded.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	locked(1), unlocked(2)

swIfPortLockIfRangeAction		1.3.6.1.4.1.89.43.6.1.4
This variable indicates which action for these interfaces should be take in locked mode and therefore relevant only in locked mode. Possible actions: discard(1) - every packet is dropped. forwardNormal(2) - every packet is forwarded according to the DST address. discardDisable(3) - drops the first packet and suspends the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	discard(1), forwardNormal(2), discardDisable(3)

swIfPortLockIfRangeTrapEn		1.3.6.1.4.1.89.43.6.1.5
This variable indicates whether to create a SNMP trap in the locked mode.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

swIfPortLockIfRangeTrapFreq		1.3.6.1.4.1.89.43.6.1.6
This variable indicates the minimal frequency (in seconds) of sending a trap for these interfaces. It's relevant only in locked mode and in trap enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..1000000

swIfExtTable		1.3.6.1.4.1.89.43.7
Display information and configuration of the device interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwIfExtEntry

swIfExtEntry		1.3.6.1.4.1.89.43.7.1
Defines the contents of each row in the swIfExtTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwIfExtEntry

swIfExtSFPSpeed		1.3.6.1.4.1.89.43.7.1.1
Configure speed of an SFP Ethernet interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	default(1), eth100M(2), eth1G(3)

rlIfMibVersion		1.3.6.1.4.1.89.54.1
MIB's version, the current version is 1.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rlIfNumOfPhPorts		1.3.6.1.4.1.89.54.2
Total number of physical ports on this device (including all stack units)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rlIfMapOfOnPhPorts		1.3.6.1.4.1.89.54.3
Each bit in this octet string indicates that the correspondig port's ifOperStatus is ON if set. The mapping of port number to bits in this octet string is as follows: The port with the L2 interface number 1 is mapped to the least significant bit of the 1st octet, the port with L2 ifNumber 2 to the next significant bit in the 1st octet, port 8 to the most-significant bit of the in the 1st octet, port 9 to the least significant bit of the 2nd octet, etc. and in general, port n to bit corresponding to 2**((n mod 8) -1) in byte n/8 + 1
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rlIfClearPortMibCounters		1.3.6.1.4.1.89.54.4
Each bit that is set in this portList represent a port that its mib counters should be reset.
Status: current	Access: read-write
OBJECT-TYPE
	PortList

rlIfNumOfUserDefinedPorts		1.3.6.1.4.1.89.54.5
The number of user defined ports on this device.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rlIfFirstOutOfBandIfIndex		1.3.6.1.4.1.89.54.6
First ifIndex of out-of-band port. This scalar exists only the device has out of band ports.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rlIfNumOfLoopbackPorts		1.3.6.1.4.1.89.54.7
The number of loopback ports on this device.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rlIfFirstLoopbackIfIndex		1.3.6.1.4.1.89.54.8
First ifIndex of loopback port. This scalar will exists only if rlIfNumOfLoopbackPorts is different from 0.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rlIfExistingPortList		1.3.6.1.4.1.89.54.9
Indicates which ports/trunks exist in the system. It doesn't indicate which are present.
Status: current	Access: read-only
OBJECT-TYPE
	PortList

rlIfBaseMACAddressPerIfIndex		1.3.6.1.4.1.89.54.10
Indicates if the system will assign a unique MAC per Ethernet port or not.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rlFlowControlCascadeMode		1.3.6.1.4.1.89.54.11
enable disable flow control on cascade ports
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

rlFlowControlCascadeType		1.3.6.1.4.1.89.54.12
define which type of ports will be affected by flow control on cascade ports
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	internalonly(1), internalexternal(2)