RAISECOM-OPTICAL-TRANSCEIVER-MIB

File: RAISECOM-OPTICAL-TRANSCEIVER-MIB.mib (117155 bytes)

Imported modules

SNMPv2-SMI	RAISECOM-BASE-MIB	SNMPv2-TC
SNMPv2-CONF	IF-MIB	RAISECOM-COMMON-MANAGEMENT-MIB
SWITCH-TC

Imported symbols

Integer32	Unsigned32	MODULE-IDENTITY
NOTIFICATION-TYPE	OBJECT-TYPE	TimeTicks
raisecomAgent	TEXTUAL-CONVENTION	MODULE-COMPLIANCE
NOTIFICATION-GROUP	OBJECT-GROUP	ifIndex
raisecomNotificationLocation	ClearVar

Defined Types

EnableVar
enable or disable a function.
TEXTUAL-CONVENTION
	INTEGER	enable(1), disable(2)

OpticalParameterType
This value indicates the optical parameter that is being monitored. Valid values are -OpticalParameterType transceiverTemperature(1) :transceiver temperature txbiasCurrent(2) :TX bias current txPower(3) :TX output power rxPower(4) :RX received optical power laserTemperature(5) :laser temperature p5V0supplyVoltage(6) :+5V supply voltage p3V3supplyVoltage(7) :+3.3V supply voltage p1V8supplyVoltage(8) :+1.8V supply voltage n5V2supplyVoltage(9) :-5.2V supply voltage apdBiasVoltage(10) :APD bias voltage p5V0supplyCurrent(11) :+5V supply currnet p3V3supplyCurrent(12) :+3.3V supply currnet p1V8supplyCurrent(13) :+1.8V supply currnet n5V2supplyCurrent(14) :-5.2V supply currnet tecCurrent(15) :TEC currnet laserWavelength(16) :laser wavelength
TEXTUAL-CONVENTION
	INTEGER	transceiverTemperature(1), txbiasCurrent(2), txPower(3), rxPower(4), laserTemperature(5), p5V0supplyVoltage(6), p3V3supplyVoltage(7), p1V8supplyVoltage(8), n5V2supplyVoltage(9), apdBiasVoltage(10), p5V0supplyCurrent(11), p3V3supplyCurrent(12), p1V8supplyCurrent(13), n5V2supplyCurrent(14), tecCurrent(15), laserWavelength(16)

OpticalParameterValue
The value of the optical parameter that is being monitored. The range of values varies depending on the type of optical parameter being monitored, as identified by a corresponding object with syntax OpticalParameterType. When the optical parameter being monitored is 'XXTemperature',the supported range is from -40000 to 125000, in units of 1/1000 degrees centigrade. Example: A value of 23500 represents a temperature reading of 23.5 degrees C. The temperature is shown in unit of degrees centigrade, and the precision is 0.1. When the optical parameter being monitored is 'txbiasCurrent',the supported range is from 0 to 131000, in units of 1/1000 mA. Example: A value of 1000 represents a TX bias current reading of 1.0mA. The 'txbiasCurrent'is shown in unit of mA, and the precision is 0.1. When the optical parameter being monitored is 'txPower',the supported range is from -40000 to 8200, in units of 1/1000 dbm. Example: A value of 77800 represents a TX output power reading of 7.78 dBm. The 'txPower' is shown in unit of dBm, and the precision is 0.1. When the optical parameter being monitored is 'rxPower',the supported range is from -40000 to 8200, in units of 1/1000 dbm. Example: A value of 7780 represents a RX received optical power reading of 7.78 dBm. The 'rxPower' is shown in unit of dBm, and the precision is 0.1. When the optical parameter being monitored is 'XXsupplyVoltage',the supported range is from 0 to 6550, in units of 1/1000 V. Example: A value of 6000 represents a XX supply Voltage eading of 6.00V. The 'XXsupplyVoltage'is shown in unit of V, and the precision is 0.01. When the optical parameter being monitored is 'apdBiasVoltage,the supported range is from 0 to 655300 , in units of 1/1000 V . Example: A value of 600000 represents a APD BiasVoltage reading of 600.0V. The 'apdBiasVoltage' is shown in unit of V, and the precision is 0.1. When the optical parameter being monitored is 'XXsupplyCurrent',the supported range is from 0 to 6553600, in units of 1/1000 mA . Example: A value of 6000000 represents a XX supply current reading of 6000.0mA. The 'XXsupplyCurrent' is shown in unit of mA, and the precision is 0.1. When the optical parameter being monitored is 'tecCurrent',the supported range is from 0 to 6553600, in units of 1/1000 mA . Example: A value of 6000000 represents a TEC Current reading of 6000.0mA. The 'tecCurrent' is shown in unit of mA, and the precision is 0.1. When the optical parameter being monitored is 'laserWavelength,the supported range is from 0 to 3276750, in units of 1/1000 nm . Example: A value of 3000000 represents a laser wavelength reading of 3000.0nm. The 'laserWavelength'is shown in unit of nm, and the precision is 0.01.
TEXTUAL-CONVENTION
	Integer32	-1000000 \| -40000..6553600

OpticalPMPeriod
This value indicates the time period over which performance monitoring data has been collected.
TEXTUAL-CONVENTION
	INTEGER	fifteenMin(1), twentyFourHour(2)

RaisecomOpticalTransceiverInfoEntry
SEQUENCE
	raisecomOpticalTransceiverType	INTEGER
	raisecomOpticalTransceiverConnectorType	INTEGER
	raisecomOpticalTransceiverVendorName	OCTET STRING
	raisecomOpticalTransceiverVendorPN	OCTET STRING
	raisecomOpticalTransceiverVendorSN	OCTET STRING
	raisecomOpticalTransceiverMediaType	INTEGER
	raisecomOpticalTransceiverTransmissionDistance	Integer32
	raisecomOpticalTransceiverAbility	Unsigned32
	raisecomOpticalTransceiverDDM	INTEGER
	raisecomOpticalTransceiverCalibrationType	INTEGER
	raisecomOpticalTransceiverRSSI	INTEGER
	raisecomOpticalTransceiverVendorRev	OCTET STRING
	raisecomOpticalTransceiverBRMax	INTEGER
	raisecomOpticalTransceiverBRMin	INTEGER
	raisecomOpticalTransceiverWavelengthContrl	INTEGER
	raisecomOpticalTransceiverWavelength	Integer32
	raisecomOpticalTransceiverWaveTolerance	OCTET STRING
	raisecomOpticalTransceiverCompatibility	OCTET STRING
	raisecomOpticalTransceiverPowerDissipation	INTEGER
	raisecomOpticalTransceiverCDR	INTEGER
	raisecomOpticalTransceiverRefClock	INTEGER
	raisecomOpticalTransceiverTransmitterType	INTEGER
	raisecomOpticalTransceiverCooled	INTEGER
	raisecomOpticalTransceiverTunalbe	INTEGER
	raisecomOpticalTransceiverDetectorType	INTEGER
	raisecomOpticalTransceiverLineLoopBack	INTEGER
	raisecomOpticalTransceiverXFILoopBack	INTEGER
	raisecomOpticalTransceiverVps	INTEGER
	raisecomOpticalTransceiverTxDis	INTEGER
	raisecomOpticalTransceiverStandby	INTEGER
	raisecomOpticalTransceiverInVpsLowPower	INTEGER
	raisecomOpticalTransceiverOutVpsLowPower	INTEGER
	raisecomOpticalTransceiverFEC	INTEGER
	raisecomOpticalTransceiverCMU	INTEGER
	raisecomOpticalTransceiverBR	INTEGER

RaisecomOpticalTransceiverDDMEntry
SEQUENCE
	raisecomOpticalTransceiverParameterType	OpticalParameterType
	raisecomOpticalTransceiverParameterValue	OpticalParameterValue
	raisecomOpticalTransceiverParamHighAlarmThresh	OpticalParameterValue
	raisecomOpticalTransceiverParamHighWarningThresh	OpticalParameterValue
	raisecomOpticalTransceiverParamLowAlarmThresh	OpticalParameterValue
	raisecomOpticalTransceiverParamLowWarningThresh	OpticalParameterValue
	raisecomOpticalTransceiverParamAlarmStatus	INTEGER
	raisecomOpticalTransceiverParamAlarmLastValue	OpticalParameterValue
	raisecomOpticalTransceiverParamAlarmLastChange	TimeTicks
	raisecomOpticalTransceiverDDM15MinValidIntervals	Unsigned32
	raisecomOpticalTransceiverDDM24HrValidIntervals	Unsigned32
	raisecomOpticalTransceiverDDMValidStatus	INTEGER

RaisecomOpticalTransceiverPMCurrentEntry
SEQUENCE
	raisecomOpticalTransceiverPMCurrentPeriod	OpticalPMPeriod
	raisecomOpticalTransceiverPMCurrentParamType	OpticalParameterType
	raisecomOpticalTransceiverPMCurrentMaxParam	OpticalParameterValue
	raisecomOpticalTransceiverPMCurrentMinParam	OpticalParameterValue
	raisecomOpticalTransceiverPMCurrentMeanParam	OpticalParameterValue

RaisecomOpticalTransceiverPMIntervalEntry
SEQUENCE
	raisecomOpticalTransceiverPMIntervalPeriod	OpticalPMPeriod
	raisecomOpticalTransceiverPMIntervalNumber	Integer32
	raisecomOpticalTransceiverPMIntervalParamType	OpticalParameterType
	raisecomOpticalTransceiverPMIntervalMaxParam	OpticalParameterValue
	raisecomOpticalTransceiverPMIntervalMinParam	OpticalParameterValue
	raisecomOpticalTransceiverPMIntervalMeanParam	OpticalParameterValue

RaisecomOpticalTransceiverCurrentStatusEntry
SEQUENCE
	raisecomOpticalTransceiverHwInfoAbsStatus	INTEGER
	raisecomOpticalTransceiverHwInfoNRStatus	INTEGER
	raisecomOpticalTransceiverHwInfoRxLosStatus	INTEGER
	raisecomOpticalTransceiverHwInfoStandby	INTEGER
	raisecomOpticalTransceiverHwInfoLaser	INTEGER
	raisecomOpticalTransceiverWaveLengthError	Integer32
	raisecomOpticalTransceiverUserWaveLength	Integer32
	raisecomOpticalTransceiverUserDataRate	INTEGER
	raisecomOpticalTransceiverUserLineLoopBack	INTEGER
	raisecomOpticalTransceiverUserXFILoopBack	INTEGER
	raisecomOpticalTransceiverPortNotifyEnable	EnableVar
	raisecomOpticalTransceiverPortDDMEnable	EnableVar
	raisecomOpticalTransceiverPortCheckPwdEnable	EnableVar
	raisecomOpticalTransceiverTxFaultCount	Integer32
	raisecomOpticalTransceiverTxFaultCountClear	ClearVar
	raisecomOpticalTransceiverSpecificationCheckStatus	INTEGER
	raisecomOpticalTransceiverTxFaultStatus	INTEGER

Defined Values

raisecomOpticalTransceiver		1.3.6.1.4.1.8886.1.18
This MIB module defines objects to monitor optical characteristics on the optical interfaces in a network element.
MODULE-IDENTITY

raisecomOpticalTransceiverGlobalEnable		1.3.6.1.4.1.8886.1.18.1
OBJECT IDENTIFIER

raisecomOpticalTransceiverNotifyEnable		1.3.6.1.4.1.8886.1.18.1.1
This object specifies the generation of device notifications, enable or disable. this object belongs to xfp and sfp.
Status: current	Access: read-write
OBJECT-TYPE
	EnableVar

raisecomOpticalTransceiverDDMEnable		1.3.6.1.4.1.8886.1.18.1.2
Enable or disable digitaldiagnotic on the device. this object belongs to xfp and sfp.
Status: current	Access: read-write
OBJECT-TYPE
	EnableVar

raisecomOpticalTransceiverCheckPwdEnable		1.3.6.1.4.1.8886.1.18.1.3
This object specifies the status of password checking on the device, enable or disable. this object belongs to xfp.
Status: current	Access: read-write
OBJECT-TYPE
	EnableVar

raisecomOpticalTransceiverPollInterval		1.3.6.1.4.1.8886.1.18.1.4
This object specifies the value of poll-interval on the device. this object belongs to xfp and sfp.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

raisecomOpticalTransceiverObjects		1.3.6.1.4.1.8886.1.18.2
OBJECT IDENTIFIER

raisecomOpticalTransceiverInfoGroup		1.3.6.1.4.1.8886.1.18.2.1
OBJECT IDENTIFIER

raisecomOpticalTransceiverDDMGroup		1.3.6.1.4.1.8886.1.18.2.2
OBJECT IDENTIFIER

raisecomOpticalTransceiverPMGroup		1.3.6.1.4.1.8886.1.18.2.3
OBJECT IDENTIFIER

raisecomOpticalTransceiverStatusGroup		1.3.6.1.4.1.8886.1.18.2.4
OBJECT IDENTIFIER

raisecomOpticalTransceiverInfoTable		1.3.6.1.4.1.8886.1.18.2.1.1
Trancetver information Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RaisecomOpticalTransceiverInfoEntry

raisecomOpticalTransceiverInfoEntry		1.3.6.1.4.1.8886.1.18.2.1.1.1
An entry in the raisecomOpticalTransceiverInfoTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RaisecomOpticalTransceiverInfoEntry

raisecomOpticalTransceiverType		1.3.6.1.4.1.8886.1.18.2.1.1.1.1
This object specifies the physical type of the transceiver, such as xfp or sfp , and so on. this object belongs to xfp and sfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), gbic(2), soldered(3), sfp(4), xbi(5), xenpak(6), xfp(7), xff(8), xfp-e(9), xpak(10), x2(11), sfpj(12)

raisecomOpticalTransceiverConnectorType		1.3.6.1.4.1.8886.1.18.2.1.1.1.2
This object specifies the connector type of the transceiver, unknown, sc, db9, hssdc, bnc-tnc, fiber-coaxial-head, fiber-outlet, lc, mt-rj, mu, sg, fiber-pigtail, mpo-parallel-optic , hssdcII, copper, rj45. this object belongs to xfp and sfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), sc(1), db9(2), hssdc(3), bnc-tnc(4), fiber-coaxial-head(5), fiber-jack(6), lc(7), mt-rj(8), mu(9), sg(10), fiber-pigtail(11), mpo-parallel-optic(12), hssdcII(20), copper(21), rj45(22)

raisecomOpticalTransceiverVendorName		1.3.6.1.4.1.8886.1.18.2.1.1.1.3
Vendor name of the interface. this object belongs to xfp and sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

raisecomOpticalTransceiverVendorPN		1.3.6.1.4.1.8886.1.18.2.1.1.1.4
Vendor part number of the interface. this object belongs to xfp and sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

raisecomOpticalTransceiverVendorSN		1.3.6.1.4.1.8886.1.18.2.1.1.1.5
Vendor serial number of the interface. this object belongs to xfp and sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

raisecomOpticalTransceiverMediaType		1.3.6.1.4.1.8886.1.18.2.1.1.1.6
Types of the fiber, single-mode, multi-modeE50, multi-mode50,multi-mode625,copper. single-modeKm,multi-modeOM3 this object belongs to xfp and sfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	single-mode(1), multi-modeE50(2), multi-mode50(3), multi-mode625(4), copper(5), single-modeKm(6), multi-modeOM3(7)

raisecomOpticalTransceiverTransmissionDistance		1.3.6.1.4.1.8886.1.18.2.1.1.1.7
The max distance which the interface could transmit, measured in meter. The object will be shown in unit of Km, and the precision is 0.001. this object belongs to xfp and sfp.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

raisecomOpticalTransceiverAbility		1.3.6.1.4.1.8886.1.18.2.1.1.1.8
This object specifies the ability of optical module digitaldiagnotic funtion. Currently, the digitaldiagnotic objects of our optical module inculde 16 parameters. this object has 32 bits, each bit represents a digital diagnotic parameter. if the bit value is 0, it means that the optical module does not provide digital diagnotic funtion for relative parameter.if the bit value is 1,it means that the optical module provides digital diagnotic funtion for relative parameter. this object belongs to xfp and sfp. The relation between parameters and bits is following: 32......16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1: The relation between parameters and bits is following: 32......16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1: But when the optical module is sfp, the 6 bit will represents the supplyVoltage of sfp.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

raisecomOpticalTransceiverDDM		1.3.6.1.4.1.8886.1.18.2.1.1.1.9
This object specifies if the transceiver supports on digital diagnostic function, support or not support.To the xfp, the default value of this object is support. this object belongs to xfp and sfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	support(1), notsupport(2)

raisecomOpticalTransceiverCalibrationType		1.3.6.1.4.1.8886.1.18.2.1.1.1.10
This object specifies the calibration type of the transceiver, internal, external, unknown. this object belongs to xfp and sfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), internal(2), external(3)

raisecomOpticalTransceiverRSSI		1.3.6.1.4.1.8886.1.18.2.1.1.1.11
This object specifies the calibration type of the transceiver, support or not support. this object belongs to xfp and sfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	support(1), notsupport(2)

raisecomOpticalTransceiverVendorRev		1.3.6.1.4.1.8886.1.18.2.1.1.1.12
the version number of the transceiver. this object belongs to xfp and sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

raisecomOpticalTransceiverBRMax		1.3.6.1.4.1.8886.1.18.2.1.1.1.13
the min data rate of the transceiver,mesured in Mbps . this object belongs to xfp and sfp. The object will be shown in unit of Gbps, and the precision is 0.1.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

raisecomOpticalTransceiverBRMin		1.3.6.1.4.1.8886.1.18.2.1.1.1.14
the min data rate of the transceiver,mesured in Mbps. this object belongs to xfp and sfp.To the sfp, the min data rate value is equal to the max data rate value. The object will be shown in unit of Gbps, and the precision is 0.1.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

raisecomOpticalTransceiverWavelengthContrl		1.3.6.1.4.1.8886.1.18.2.1.1.1.15
if the transceiver supports on wavelength control support,notsupport. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	support(1), notsupport(2)

raisecomOpticalTransceiverWavelength		1.3.6.1.4.1.8886.1.18.2.1.1.1.16
Wavelength of the interface, measured in pm(0.001nm). this object belongs to xfp. The object will be shown in unit of nm, and the precision is 0.01.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

raisecomOpticalTransceiverWaveTolerance		1.3.6.1.4.1.8886.1.18.2.1.1.1.17
the range of laser wavelength from nominal wavelength,mesured in pm(0.001*nm). this object belongs to xfp. The object will be shown in unit of nm, and the precision is 0.01.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

raisecomOpticalTransceiverCompatibility		1.3.6.1.4.1.8886.1.18.2.1.1.1.18
the compatibility type that the transceiver supports,such as 10GBASE-SR. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

raisecomOpticalTransceiverPowerDissipation		1.3.6.1.4.1.8886.1.18.2.1.1.1.19
the max power dissipation of the transceiver, p1W5,p2W5,p3W5,exceed3W5. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	p1W5(1), p2W5(2), p3W5(3), exceed(4)

raisecomOpticalTransceiverCDR		1.3.6.1.4.1.8886.1.18.2.1.1.1.20
the optical module supports on CDR fundtion. support,notsupport. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	support(1), notsupport(2)

raisecomOpticalTransceiverRefClock		1.3.6.1.4.1.8886.1.18.2.1.1.1.21
if the transceiver requires outside reference clock required,notrequired. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	required(1), notrequired(2)

raisecomOpticalTransceiverTransmitterType		1.3.6.1.4.1.8886.1.18.2.1.1.1.22
The transmitter type of the transceiver,such as 850 nm VCSEL. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	vcsel850nm(1), vcsel1310nm(2), vcsel1550nm(3), fp1310nm(4), dfb1310nm(5), dfb1550nm(6), eml1310nm(7), eml1550nm(8), copper-others(9)

raisecomOpticalTransceiverCooled		1.3.6.1.4.1.8886.1.18.2.1.1.1.24
The transmitter cooled type of the transceiver cooled,uncooled. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cooled(1), uncooled(2)

raisecomOpticalTransceiverTunalbe		1.3.6.1.4.1.8886.1.18.2.1.1.1.25
The transmitter tunable type of the transceiver tunable,untunable. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	tunable(1), untunable(2)

raisecomOpticalTransceiverDetectorType		1.3.6.1.4.1.8886.1.18.2.1.1.1.26
The detector type of the transceiver pin, apd. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	pin(1), apd(2)

raisecomOpticalTransceiverLineLoopBack		1.3.6.1.4.1.8886.1.18.2.1.1.1.27
The transceiver support status of sideline loop-back control support,notsupport. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	support(1), notsupport(2)

raisecomOpticalTransceiverXFILoopBack		1.3.6.1.4.1.8886.1.18.2.1.1.1.28
The transceiver support status of XFI loop-back control support,notsupport. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	support(1), notsupport(2)

raisecomOpticalTransceiverVps		1.3.6.1.4.1.8886.1.18.2.1.1.1.29
This object specifies if the optical module supports on VPS support,notsupport. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	support(1), notsupport(2)

raisecomOpticalTransceiverTxDis		1.3.6.1.4.1.8886.1.18.2.1.1.1.30
The transceiver support status of software control the transmitter status support,notsupport. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	support(1), notsupport(2)

raisecomOpticalTransceiverStandby		1.3.6.1.4.1.8886.1.18.2.1.1.1.31
The transceiver support status of software control the standby mode. support,notsupport. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	support(1), notsupport(2)

raisecomOpticalTransceiverInVpsLowPower		1.3.6.1.4.1.8886.1.18.2.1.1.1.32
The VPS in low power support status of the transceiver support,notsupport. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	support(1), notsupport(2)

raisecomOpticalTransceiverOutVpsLowPower		1.3.6.1.4.1.8886.1.18.2.1.1.1.33
The VPS out low power support status of the transceiver support,notsupport. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	support(1), notsupport(2)

raisecomOpticalTransceiverFEC		1.3.6.1.4.1.8886.1.18.2.1.1.1.34
The FEC support status of transceiver support,notsupport. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	support(1), notsupport(2)

raisecomOpticalTransceiverCMU		1.3.6.1.4.1.8886.1.18.2.1.1.1.35
The CMU support status of transceiver support,notsupport. this object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	support(1), notsupport(2)

raisecomOpticalTransceiverBR		1.3.6.1.4.1.8886.1.18.2.1.1.1.36
This object specifies the Nominal bitrate of the transceiver, 125Mbps, 155Mbps, 622Mbps, 1.25Gbps, 2.5Gbps. this object belongs to xfp and sfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), bitrate-125Mbps(1), bitrate-155Mbps(2), bitrate-622Mbps(6), bitrate-1DOT25Gbps(13), bitrate-2DOT5Gbps(19)

raisecomOpticalTransceiverDDMTable		1.3.6.1.4.1.8886.1.18.2.2.1
This table provides objects to monitor optical parameters in a network element.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RaisecomOpticalTransceiverDDMEntry

raisecomOpticalTransceiverDDMEntry		1.3.6.1.4.1.8886.1.18.2.2.1.1
An entry in the raisecomOpticalTransceiverMonTable provides objects to monitor an optical parameter at an optical interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	RaisecomOpticalTransceiverDDMEntry

raisecomOpticalTransceiverParameterType		1.3.6.1.4.1.8886.1.18.2.2.1.1.1
This object specifies the optical parameter that is being monitored in this entry. This object belongs to xfp/sfp.
Status: current	Access: not-accessible
OBJECT-TYPE
	OpticalParameterType

raisecomOpticalTransceiverParameterValue		1.3.6.1.4.1.8886.1.18.2.2.1.1.2
This object gives the value measured for the particular optical parameter specified by the raisecomOpticalMonParameterType object. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OpticalParameterValue

raisecomOpticalTransceiverParamHighAlarmThresh		1.3.6.1.4.1.8886.1.18.2.2.1.1.3
This object gives the high alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by raisecomOpticalParameterValue goes from below the value of this object to above the value of this object, or if the initial value of raisecomOpticalParameterValue exceeds the value of this object. This alarm will be indicated in the raisecomOpticalParamAlarmStatus object. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OpticalParameterValue

raisecomOpticalTransceiverParamHighWarningThresh		1.3.6.1.4.1.8886.1.18.2.2.1.1.4
This object is used to set a high warning threshold on the optical parameter being monitored. A threshold crossing condition will be indicated if the value given by raisecomOpticalParameterValue goes from below the value of this object to above the value of this object, or if the initial value of raisecomOpticalParameterValue exceeds the value of this object. This alarm will be indicated in the raisecomOpticalParamAlarmStatus object. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OpticalParameterValue

raisecomOpticalTransceiverParamLowAlarmThresh		1.3.6.1.4.1.8886.1.18.2.2.1.1.5
This object is used to set a low alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by raisecomOpticalParameterValue goes from above the value of this object to below the value of this object, or if the initial value of raisecomOpticalParameterValue is lower than the value of this object. This alarm will be indicated in the raisecomOpticalParamAlarmStatus object .. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OpticalParameterValue

raisecomOpticalTransceiverParamLowWarningThresh		1.3.6.1.4.1.8886.1.18.2.2.1.1.6
This object is used to set a low warning threshold on the optical parameter being monitored. A threshold crossing condition will be indicated if the value given by raisecomOpticalParameterValue goes from above the value of this object to below the value of this object, or if the initial value of raisecomOpticalParameterValue object is lower than the value of this object. For network elements in the status indications, this threshold violation will be indicated in the raisecomOpticalParamAlarmStatus object . This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OpticalParameterValue

raisecomOpticalTransceiverParamAlarmStatus		1.3.6.1.4.1.8886.1.18.2.2.1.1.7
This object is used to indicate the current status of the thresholds for the monitored optical parameter on the interface. If a threshold is currently being exceeded on the interface, the object will be set. Otherwise, the object will be set to 1. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), normal(1), high-alarm(2), high-warning(3), low-alarm(4), low-warning(5)

raisecomOpticalTransceiverParamAlarmLastValue		1.3.6.1.4.1.8886.1.18.2.2.1.1.8
This object indicates the optical parameter value at the last time a threshold related to a particular optical parameter was exceeded on the interface. If no threshold value is currently being exceeded, then the value '-1000000' is returned. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OpticalParameterValue

raisecomOpticalTransceiverParamAlarmLastChange		1.3.6.1.4.1.8886.1.18.2.2.1.1.9
This object specifies the value of sysUpTime at the last time a threshold related to a particular optical parameter was exceeded on the interface. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

raisecomOpticalTransceiverDDM15MinValidIntervals		1.3.6.1.4.1.8886.1.18.2.2.1.1.10
This object gives the number of previous 15 minute intervals for which valid performance monitoring data has been stored on the interface. The value of this object will be n (where n is the maximum number of 15 minute intervals supported at this interface), unless the measurement was (re-)started within the last (nx15) minutes, in which case the value will be the number of previous 15 minute intervals for which the agent has some data. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..96

raisecomOpticalTransceiverDDM24HrValidIntervals		1.3.6.1.4.1.8886.1.18.2.2.1.1.11
This object gives the number of previous 24 hour intervals for which valid performance monitoring data has been stored on the interface. The max value of this object is 7, it means that the user can look up 7days history information. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..7

raisecomOpticalTransceiverDDMValidStatus		1.3.6.1.4.1.8886.1.18.2.2.1.1.12
This object indicates the parameter row is valid or invalid. The object value is 'valide' when the module is present and supporting digitaldiagnotic. The object value is 'invalid' when the module is absent, or when the module is present and not supporting digitaldiagnotic. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), valid(1), invalid(2)

raisecomOpticalTransceiverPMCurrentTable		1.3.6.1.4.1.8886.1.18.2.3.1
This table contains performance monitoring data for the various optical parameters, collected over the current 15 minute or the current 24 hour interval.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RaisecomOpticalTransceiverPMCurrentEntry

raisecomOpticalTransceiverPMCurrentEntry		1.3.6.1.4.1.8886.1.18.2.3.1.1
An entry in the raisecomOpticalTransceiverPMCurrentTable. It contains performance monitoring data for a monitored optical parameter at an interface, collected over the current 15 minute or the current 24 hour interval.
Status: current	Access: not-accessible
OBJECT-TYPE
	RaisecomOpticalTransceiverPMCurrentEntry

raisecomOpticalTransceiverPMCurrentPeriod		1.3.6.1.4.1.8886.1.18.2.3.1.1.1
This object indicates whether the optical parameter values given in this entry are collected over the current 15 minute or the current 24 hour interval. This object belongs to xfp/sfp.
Status: current	Access: not-accessible
OBJECT-TYPE
	OpticalPMPeriod

raisecomOpticalTransceiverPMCurrentParamType		1.3.6.1.4.1.8886.1.18.2.3.1.1.2
This object specifies the optical parameter that is being monitored, in this entry. This object belongs to xfp/sfp.
Status: current	Access: not-accessible
OBJECT-TYPE
	OpticalParameterType

raisecomOpticalTransceiverPMCurrentMaxParam		1.3.6.1.4.1.8886.1.18.2.3.1.1.3
This object gives the maximum value measured for the monitored optical parameter, in the current 15 minute or the current 24 hour interval. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OpticalParameterValue

raisecomOpticalTransceiverPMCurrentMinParam		1.3.6.1.4.1.8886.1.18.2.3.1.1.4
This object gives the minimum value measured for the monitored optical parameter, in the current 15 minute or the current 24 hour interval. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OpticalParameterValue

raisecomOpticalTransceiverPMCurrentMeanParam		1.3.6.1.4.1.8886.1.18.2.3.1.1.5
This object gives the average value of the monitored optical parameter, in the current 15 minute or the current 24 hour interval. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OpticalParameterValue

raisecomOpticalTransceiverPMIntervalTable		1.3.6.1.4.1.8886.1.18.2.3.2
This table stores performance monitoring data for the various optical parameters, collected over previous intervals. This table can have entries for one complete 24 hour interval and up to 96 complete 15 minute intervals. A system is required to store at least 4 completed 15 minute intervals. The number of valid 15 minute intervals in this table is indicated by the raisecomOpticalTransceiverDDM15MinValidIntervals object and the number of valid 24 hour intervals is indicated by the raisecomOpticalTransceiverDDM24HrValidIntervals object. when the optical module is removed from the device, the relative history records will be cleaned.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RaisecomOpticalTransceiverPMIntervalEntry

raisecomOpticalTransceiverPMIntervalEntry		1.3.6.1.4.1.8886.1.18.2.3.2.1
An entry in the raisecomOpticalTransceiverPMIntervalTable. It contains performance monitoring data for an optical parameter, collected over a previous interval.
Status: current	Access: not-accessible
OBJECT-TYPE
	RaisecomOpticalTransceiverPMIntervalEntry

raisecomOpticalTransceiverPMIntervalPeriod		1.3.6.1.4.1.8886.1.18.2.3.2.1.1
This object indicates whether the optical parameter values, given in this entry, are collected over a period of 15 minutes or 24 hours. This object belongs to xfp/sfp.
Status: current	Access: not-accessible
OBJECT-TYPE
	OpticalPMPeriod

raisecomOpticalTransceiverPMIntervalNumber		1.3.6.1.4.1.8886.1.18.2.3.2.1.2
A number between 1 and 96, which identifies the interval for which the set of optical parameter values is available. The interval identified by 1 is the most recently completed 15 minute or 24 hour interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. This object belongs to xfp/sfp.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..96

raisecomOpticalTransceiverPMIntervalParamType		1.3.6.1.4.1.8886.1.18.2.3.2.1.3
This object specifies the optical parameter that is being monitored, in this entry. This object belongs to xfp/sfp.
Status: current	Access: not-accessible
OBJECT-TYPE
	OpticalParameterType

raisecomOpticalTransceiverPMIntervalMaxParam		1.3.6.1.4.1.8886.1.18.2.3.2.1.4
This object gives the maximum value measured for the optical parameter, in a particular 15 minute or 24 hour interval. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OpticalParameterValue

raisecomOpticalTransceiverPMIntervalMinParam		1.3.6.1.4.1.8886.1.18.2.3.2.1.5
This object gives the minimum value measured for the optical parameter, in a particular 15 minute or 24 hour interval. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OpticalParameterValue

raisecomOpticalTransceiverPMIntervalMeanParam		1.3.6.1.4.1.8886.1.18.2.3.2.1.6
This object gives the average value of the measured optical parameter, in a particular 15 minute or 24 hour interval. This object belongs to xfp/sfp.
Status: current	Access: read-only
OBJECT-TYPE
	OpticalParameterValue

raisecomOpticalTransceiverCurrentStatusTable		1.3.6.1.4.1.8886.1.18.2.4.1
This table stores the hard ware information and the information set by user of the transceiver. This object belongs to xfp/sfp.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RaisecomOpticalTransceiverCurrentStatusEntry

raisecomOpticalTransceiverCurrentStatusEntry		1.3.6.1.4.1.8886.1.18.2.4.1.1
An entry in the raisecomOpticalTransceiverCurrentStatusTable. It contains performance monitoring data for an optical parameter, collected over a previous interval. This object belongs to xfp/sfp.
Status: current	Access: not-accessible
OBJECT-TYPE
	RaisecomOpticalTransceiverCurrentStatusEntry

raisecomOpticalTransceiverHwInfoAbsStatus		1.3.6.1.4.1.8886.1.18.2.4.1.1.1
This object specifies if the optical module is absent present,absent. This object belongs to xfp and sfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	absent(1), present(2)

raisecomOpticalTransceiverHwInfoNRStatus		1.3.6.1.4.1.8886.1.18.2.4.1.1.2
This object specifies if the optical module is ready for operation. ready,notready. This object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ready(1), notready(2)

raisecomOpticalTransceiverHwInfoRxLosStatus		1.3.6.1.4.1.8886.1.18.2.4.1.1.3
This object specifies if the optical module operation losses the receiving signal normal,loss. This object belongs to xfp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), loss(2)

raisecomOpticalTransceiverHwInfoStandby		1.3.6.1.4.1.8886.1.18.2.4.1.1.4
This object specifies if the optical module works under standby mode. normal,standby. This object belongs to xfp.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), standby(2)

raisecomOpticalTransceiverHwInfoLaser		1.3.6.1.4.1.8886.1.18.2.4.1.1.5
This object specifies if the optical module laser is turned on on,off. This object belongs to xfp.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

raisecomOpticalTransceiverWaveLengthError		1.3.6.1.4.1.8886.1.18.2.4.1.1.6
This object specifies error between the actual wavelength and the wavelength set by the user,measured in pm. This object belongs to xfp. The object will be shown in unit of nm, and the precision is 0.001.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

raisecomOpticalTransceiverUserWaveLength		1.3.6.1.4.1.8886.1.18.2.4.1.1.7
This object specifies the wavelength value of the optical module set by user,measured in pm. This object belongs to xfp. The object will be shown in unit of nm, and the precision is 0.01.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..3276800

raisecomOpticalTransceiverUserDataRate		1.3.6.1.4.1.8886.1.18.2.4.1.1.8
This object specifies the data rate of the optical module set by user,measured in Mbps. This object belongs to xfp. The object will be shown in unit of Gbps, and the precision is 0.1.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	9500..12500

raisecomOpticalTransceiverUserLineLoopBack		1.3.6.1.4.1.8886.1.18.2.4.1.1.9
This object specifies if the sideline loop-back is tuned on , user can change the loop back mode through the object. normal,lineLoopback. This object belongs to xfp.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), lineLoopback(2)

raisecomOpticalTransceiverUserXFILoopBack		1.3.6.1.4.1.8886.1.18.2.4.1.1.10
This object specifies if the XFI loop-back is tuned on user can change the loop back mode through the object. normal,xfiLoopback. This object belongs to xfp.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), xfiLoopback(2)

raisecomOpticalTransceiverPortNotifyEnable		1.3.6.1.4.1.8886.1.18.2.4.1.1.11
This object specifies the generation of a port notifications, enable or disable. This object belongs to xfp and sfp.
Status: current	Access: read-write
OBJECT-TYPE
	EnableVar

raisecomOpticalTransceiverPortDDMEnable		1.3.6.1.4.1.8886.1.18.2.4.1.1.12
This object specifies the status of digitaldiagnotic on a port, enable or disable. This object belongs to xfp and sfp.
Status: current	Access: read-write
OBJECT-TYPE
	EnableVar

raisecomOpticalTransceiverPortCheckPwdEnable		1.3.6.1.4.1.8886.1.18.2.4.1.1.13
This object specifies the status of password checking on a port, enable or disable. This object belongs to xfp.
Status: current	Access: read-write
OBJECT-TYPE
	EnableVar

raisecomOpticalTransceiverTxFaultCount		1.3.6.1.4.1.8886.1.18.2.4.1.1.14
This object specifies the number of tx-fault signals.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

raisecomOpticalTransceiverTxFaultCountClear		1.3.6.1.4.1.8886.1.18.2.4.1.1.15
This object specifies clear the statistcs of tx-fault signals.
Status: current	Access: read-write
OBJECT-TYPE
	ClearVar

raisecomOpticalTransceiverSpecificationCheckStatus		1.3.6.1.4.1.8886.1.18.2.4.1.1.16
This object specifies the check status, accord(0)specifies the optical module accord with industrial. not-accord(2) specifies the optical module not accord with industrial.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), accord(1), not-accord(2)

raisecomOpticalTransceiverTxFaultStatus		1.3.6.1.4.1.8886.1.18.2.4.1.1.17
This object specifies the tx-fault status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), tx-fault(2)

raisecomOpticalTransceiverNotifications		1.3.6.1.4.1.8886.1.18.3
OBJECT IDENTIFIER

raisecomOpticalTransceiverAbsentTrap		1.3.6.1.4.1.8886.1.18.3.1
This notification is sent when the optical module is removed from the device. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverPresentTrap		1.3.6.1.4.1.8886.1.18.3.2
This notification is sent when the optical module is plugged into the device. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverNRAlarmTrap		1.3.6.1.4.1.8886.1.18.3.3
This notification is sent when the transmitted or received data of optical module is invalid. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverNRNormalTrap		1.3.6.1.4.1.8886.1.18.3.4
This notification is sent when the transmitted or received data of optical module is valid. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverRxLosAlarmTrap		1.3.6.1.4.1.8886.1.18.3.5
This notification is sent when the optical module receiving signal is lost. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverRxLosNormaTrap		1.3.6.1.4.1.8886.1.18.3.6
This notification is sent when the optical module receiving signal is back to normal. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverCheckPwdFailureTrap		1.3.6.1.4.1.8886.1.18.3.7
This notification is sent when the optical module password checking is failed. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverCheckPwdSucceedTrap		1.3.6.1.4.1.8886.1.18.3.8
This notification is sent when the optical module password cheching is successful. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverParamAlarmTrap		1.3.6.1.4.1.8886.1.18.3.9
This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverParamAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.3.10
This notification is sent when the optical module parameter value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverParamWarningTrap		1.3.6.1.4.1.8886.1.18.3.11
This notification is sent when the optical module parameter value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverParamWarningNormalTrap		1.3.6.1.4.1.8886.1.18.3.12
This notification is sent when the optical module parameter value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverLaserBackLightAlarmTrap		1.3.6.1.4.1.8886.1.18.3.13
This notification is sent when the optical module password cheching is successful. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverLaserBackLightAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.3.14
This notification is sent when the optical module password cheching is successful. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverLaserLifeAlarmTrap		1.3.6.1.4.1.8886.1.18.3.15
This notification is sent when the optical module password cheching is successful. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverLaserLifeAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.3.16
This notification is sent when the optical module password cheching is successful. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverParamLowAlarmTrap		1.3.6.1.4.1.8886.1.18.3.17
This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverParamLowAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.3.18
This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverParamLowWarningTrap		1.3.6.1.4.1.8886.1.18.3.19
This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverParamLowWarningNormalTrap		1.3.6.1.4.1.8886.1.18.3.20
This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverParamNotifications		1.3.6.1.4.1.8886.1.18.4
OBJECT IDENTIFIER

raisecomOpticalTransceiverTemperatureAlarmTrap		1.3.6.1.4.1.8886.1.18.4.1
This notification is sent when the optical module Temperature value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTemperatureAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.2
This notification is sent when the optical module Temperature value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTemperatureWarningTrap		1.3.6.1.4.1.8886.1.18.4.3
This notification is sent when the optical module Temperature value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTemperatureWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.4
This notification is sent when the optical module Temperature value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTxbiasCurrentAlarmTrap		1.3.6.1.4.1.8886.1.18.4.5
This notification is sent when the optical module Tx bias Current value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTxbiasCurrentAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.6
This notification is sent when the optical module Tx bias Current value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTxbiasCurrentWarningTrap		1.3.6.1.4.1.8886.1.18.4.7
This notification is sent when the optical module Tx bias Current value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTxbiasCurrentWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.8
This notification is sent when the optical module Tx bias Current value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTxPowerAlarmTrap		1.3.6.1.4.1.8886.1.18.4.9
This notification is sent when the optical module Tx Power value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTxPowerAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.10
This notification is sent when the optical module Tx Power value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTxPowerWarningTrap		1.3.6.1.4.1.8886.1.18.4.11
This notification is sent when the optical module Tx Power value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTxPowerWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.12
This notification is sent when the optical module Tx Power value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverRxPowerAlarmTrap		1.3.6.1.4.1.8886.1.18.4.13
This notification is sent when the optical module Rx Power value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverRxPowerWarningTrap		1.3.6.1.4.1.8886.1.18.4.14
This notification is sent when the optical module Rx Power value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverRxPowerWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.15
This notification is sent when the optical module Rx Power value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverRxPowerAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.16
This notification is sent when the optical module Rx Power value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverLaserTemperatureAlarmTrap		1.3.6.1.4.1.8886.1.18.4.17
This notification is sent when the optical module Laser Temperature value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverLaserTemperatureWarningTrap		1.3.6.1.4.1.8886.1.18.4.18
This notification is sent when the optical module Laser Temperature value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverLaserTemperatureWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.19
This notification is sent when the optical module Laser Temperature value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverLaserTemperatureAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.20
This notification is sent when the optical module Laser Temperature value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP5V0supplyVoltageAlarmTrap		1.3.6.1.4.1.8886.1.18.4.21
This notification is sent when the optical module +5.0V supply Voltage value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP5V0supplyVoltageWarningTrap		1.3.6.1.4.1.8886.1.18.4.22
This notification is sent when the optical module +5.0V supply Voltage value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP5V0supplyVoltageWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.23
This notification is sent when the optical module +5.0V supply Voltage value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP5V0supplyVoltageAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.24
This notification is sent when the optical module +5.0V supply Voltage value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP3V3supplyVoltageAlarmTrap		1.3.6.1.4.1.8886.1.18.4.25
This notification is sent when the optical module +3.3V supply Voltage value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP3V3supplyVoltageWarningTrap		1.3.6.1.4.1.8886.1.18.4.26
This notification is sent when the optical module +3.3V supply Voltage value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP3V3supplyVoltageWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.27
This notification is sent when the optical module +3.3V supply Voltage value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP3V3supplyVoltageAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.28
This notification is sent when the optical module +3.3V supply Voltage value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP1V8supplyVoltageAlarmTrap		1.3.6.1.4.1.8886.1.18.4.29
This notification is sent when the optical module +1.8v supply Voltage value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP1V8supplyVoltageWarningTrap		1.3.6.1.4.1.8886.1.18.4.30
This notification is sent when the optical module +1.8v supply Voltage value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP1V8supplyVoltageWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.31
This notification is sent when the optical module +1.8v supply Voltage value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP1V8supplyVoltageAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.32
This notification is sent when the optical module +1.8v supply Voltage value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverN5V2supplyVoltageAlarmTrap		1.3.6.1.4.1.8886.1.18.4.33
This notification is sent when the optical module -5.2v supply Voltage value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverN5V2supplyVoltageWarningTrap		1.3.6.1.4.1.8886.1.18.4.34
This notification is sent when the optical module -5.2v supply Voltage value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverN5V2supplyVoltageWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.35
This notification is sent when the optical module -5.2v supply Voltage value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverN5V2supplyVoltageAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.36
This notification is sent when the optical module -5.2v supply Voltage value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverApdBiasVoltageAlarmTrap		1.3.6.1.4.1.8886.1.18.4.37
This notification is sent when the optical module APD Bias Voltage value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverApdBiasVoltageWarningTrap		1.3.6.1.4.1.8886.1.18.4.38
This notification is sent when the optical module APD Bias Voltage value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverApdBiasVoltageWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.39
This notification is sent when the optical module APD Bias Voltage value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverApdBiasVoltageAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.40
This notification is sent when the optical module APD Bias Voltage value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP5V0supplyCurrentAlarmTrap		1.3.6.1.4.1.8886.1.18.4.41
This notification is sent when the optical module +5.0V supply Current value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP5V0supplyCurrentWarningTrap		1.3.6.1.4.1.8886.1.18.4.42
This notification is sent when the optical module +5.0V supply Current value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP5V0supplyCurrentWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.43
This notification is sent when the optical module +5.0V supply Current value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP5V0supplyCurrentAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.44
This notification is sent when the optical module +5.0V supply Current value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP3V3supplyCurrentAlarmTrap		1.3.6.1.4.1.8886.1.18.4.45
This notification is sent when the optical module +3.3V supply Current value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP3V3supplyCurrentWarningTrap		1.3.6.1.4.1.8886.1.18.4.46
This notification is sent when the optical module +3.3V supply Current value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP3V3supplyCurrentWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.47
This notification is sent when the optical module +3.3V supply Current value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP3V3supplyCurrentAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.48
This notification is sent when the optical module +3.3V supply Current value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP1V8supplyCurrentAlarmTrap		1.3.6.1.4.1.8886.1.18.4.49
This notification is sent when the optical module +1.8V supply Current value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP1V8supplyCurrentWarningTrap		1.3.6.1.4.1.8886.1.18.4.50
This notification is sent when the optical module +1.8V supply Current value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP1V8supplyCurrentWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.51
This notification is sent when the optical module +1.8V supply Current value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverP1V8supplyCurrentAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.52
This notification is sent when the optical module +1.8V supply Current value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverN5V2supplyCurrentAlarmTrap		1.3.6.1.4.1.8886.1.18.4.53
This notification is sent when the optical module -5.2V supply Current value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverN5V2supplyCurrentWarningTrap		1.3.6.1.4.1.8886.1.18.4.54
This notification is sent when the optical module -5.2V supply Current value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverN5V2supplyCurrentWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.55
This notification is sent when the optical module -5.2V supply Current value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverN5V2supplyCurrentAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.56
This notification is sent when the optical module -5.2V supply Current value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTecCurrentAlarmTrap		1.3.6.1.4.1.8886.1.18.4.57
This notification is sent when the optical module TecCurrent value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTecCurrentWarningTrap		1.3.6.1.4.1.8886.1.18.4.58
This notification is sent when the optical module TecCurrent value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTecCurrentWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.59
This notification is sent when the optical module TecCurrent value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTecCurrentAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.60
This notification is sent when the optical module TecCurrent value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverLaserWavelengthAlarmTrap		1.3.6.1.4.1.8886.1.18.4.61
This notification is sent when the optical module laserWavelength value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverLaserWavelengthWarningTrap		1.3.6.1.4.1.8886.1.18.4.62
This notification is sent when the optical module laserWavelength value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverLaserWavelengthWarningNormalTrap		1.3.6.1.4.1.8886.1.18.4.63
This notification is sent when the optical module laserWavelength value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverLaserWavelengthAlarmNormalTrap		1.3.6.1.4.1.8886.1.18.4.64
This notification is sent when the optical module laserWavelength value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTxFaultTrap		1.3.6.1.4.1.8886.1.18.4.65
This notification is sent when the SFP optical module occures Tx-fault signal. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE

raisecomOpticalTransceiverTxNormalTrap		1.3.6.1.4.1.8886.1.18.4.66
This notification is sent when the SFP optical module cancels the Tx-fault signal. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
Status: current	Access: read-only
NOTIFICATION-TYPE