REDSTONE-IF-MIB
File:
REDSTONE-IF-MIB.mib (9801 bytes)
Imported modules
Imported symbols
Defined Types
| RsIfType |
|
| Interface type identification for physical-, link-, and
network-layer interfaces. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
ip(0), ppp(1), ds0(2), ds1(3), ds3(4), frameRelay(5), ethernet(6), sonet(7), sonetPath(8), atm(9), aal5(10), atmSubInterface(11), ft1(12), hdlc(13), ipLoopback(14), ipVirtual(15), frSubInterface(16), pppoe(17), pppoeSubInterface(18) |
|
| RsIfEntry |
|
| SEQUENCE |
|
|
|
| |
rsIfType |
RsIfType |
|
| RsIfInvStackEntry |
|
| SEQUENCE |
|
|
|
| |
rsIfInvStackStatus |
RowStatus |
|
Defined Values
| rsIfMIB |
1.3.6.1.4.1.2773.2.3 |
| The Generic Interfaces MIB for the
Redstone Communications Inc. enterprise. |
| MODULE-IDENTITY |
|
|
|
| rsIf |
1.3.6.1.4.1.2773.2.3.1.1 |
| OBJECT IDENTIFIER |
|
|
|
| rsIfObjects |
1.3.6.1.4.1.2773.2.3.1.1.1 |
| OBJECT IDENTIFIER |
|
|
|
| rsIfTable |
1.3.6.1.4.1.2773.2.3.1.1.1.1 |
| This table contains a corresponding entry for each entry found
in the standard Generic Interfaces MIB ifTable/ifXTable. The entries
in this table contain supplementary generic interface characteristics.
Entries in ifTable/ifXTable and in this table are created/deleted
as a consequence of hardware detection, or of management configuration
via standard or enterprise type-specific interface MIBs. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
RsIfEntry |
|
| rsIfEntry |
1.3.6.1.4.1.2773.2.3.1.1.1.1.1 |
| An entry representing an interface's enterprise-defined generic
interface characteristics. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
RsIfEntry |
|
|
| rsIfType |
1.3.6.1.4.1.2773.2.3.1.1.1.1.1.1 |
| Identifies the type of this interface. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
RsIfType |
|
|
| rsIfInvStackTable |
1.3.6.1.4.1.2773.2.3.1.1.1.2 |
| A table containing information on the relationships between
the multiple sub-layers of network interfaces. In
particular, it contains information on which sub-layers run
'underneath' which other sub-layers, where each sub-layer
corresponds to a conceptual row in the ifTable. For
example, when the sub-layer with ifIndex value x runs
underneath the sub-layer with ifIndex value y, then this
table contains:
rsIfInvStackStatus.x.y=active
For each ifIndex value, I, which identifies an active
interface, there are always at least two instantiated rows
in this table associated with I. For one of these rows, I
is the value of ifStackHigherLayer; for the other, I is the
value of ifStackLowerLayer. (If I is not involved in
multiplexing, then these are the only two rows associated
with I.)
For example, two rows exist even for an interface which has
no others stacked on top or below it:
ifStackStatus.x.0=active
ifStackStatus.0.x=active
This table contains exactly the same number of rows as the
ifStackTable, but the rows appear in a different order. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
RsIfInvStackEntry |
|
| rsIfInvStackEntry |
1.3.6.1.4.1.2773.2.3.1.1.1.2.1 |
| Information on a particular relationship between two sub-
layers, specifying that one sub-layer runs underneath the
other sub-layer. Each sub-layer corresponds to a conceptual
row in the ifTable. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
RsIfInvStackEntry |
|
|
| rsIfInvStackStatus |
1.3.6.1.4.1.2773.2.3.1.1.1.2.1.1 |
| The status of the relationship between two sub-layers.
An instance of this object exists for each instance of the
ifStackStatus object, and vice versa. For example, if the
variable ifStackStatus.H.L exists, then the variable
rsIfInvStackStatus.L.H must also exist, and vice versa. In
addition, the two variables always have the same value.
However, unlike ifStackStatus, the rsIfInvStackStatus object
is NOT write-able. A network management application wishing
to change a relationship between sub-layers H and L cannot
do so by modifying the value of rsIfInvStackStatus.L.H, but
must instead modify the value of ifStackStatus.H.L. After
the ifStackTable is modified, the change will be reflected
in this table. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| rsIfGroups |
1.3.6.1.4.1.2773.2.3.1.1.4.2 |
| OBJECT IDENTIFIER |
|
|
|
| rsIfCompliance |
1.3.6.1.4.1.2773.2.3.1.1.4.1.1 |
| The compliance statement for entities which implement
the Redstone Generic Interfaces MIB. |
| Status: current |
Access: read-only |
| MODULE-COMPLIANCE |
|
|
|
| rsIfGroup |
1.3.6.1.4.1.2773.2.3.1.1.4.2.1 |
| A collection of objects providing management capability
capability of generic interfaces in a Redstone product. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| rsIfInvStackGroup |
1.3.6.1.4.1.2773.2.3.1.1.4.2.2 |
| A collection of objects providing inverted information on
the layering of MIB-II interfaces. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|