RETIX-METROLAN-MIB
File:
RETIX-METROLAN-MIB.mib (19848 bytes)
Imported modules
Imported symbols
Defined Types
PortVLANEntry |
|
SEQUENCE |
|
|
|
|
ssVLANEntryPortID |
INTEGER |
|
|
ssVLANEntryVLANID |
INTEGER |
|
|
ssVLANEntryEdit |
INTEGER |
|
Defined Values
retix |
1.3.6.1.4.1.72 |
OBJECT IDENTIFIER |
|
|
|
ssStakBus |
1.3.6.1.4.1.72.20.3 |
OBJECT IDENTIFIER |
|
|
|
ssSlip |
1.3.6.1.4.1.72.20.5 |
OBJECT IDENTIFIER |
|
|
|
atmBWGBandwidth |
1.3.6.1.2.1.37.1.1 |
The bandwidth amount (in Kbps) assigned to a
specific bandwidth group. Total bandwidth for all
eight groups can not exceed the maximum, which is 36880. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..8 |
|
atmBWGConfig |
1.3.6.1.2.1.37.1.2 |
this carry out the actual SET of the bandwidth group.
a SYSTEM RESET will be executed for the changes in
bandwidth group to take effect. |
Status: mandatory |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
go(1) |
|
atmRX-VCI |
1.3.6.1.2.1.37.2.1 |
Receive VCI #. can be set as the same as atmTX-VCI |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
35..1023 |
|
atmRX-VPI |
1.3.6.1.2.1.37.2.2 |
Receive VPI #. can be set as the same as atmTX-VPI |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..255 |
|
atmTX-VCI |
1.3.6.1.2.1.37.2.3 |
Transmit VCI #. choose a unique number for each ATM
logical port. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
35..1023 |
|
atmTX-VPI |
1.3.6.1.2.1.37.2.4 |
Transmit VPI #. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..255 |
|
atmBWG |
1.3.6.1.2.1.37.2.5 |
Bandwidth group number. That paticular bandwidthgroup
must be configured with a positive bandwidth |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..8 |
|
atmEncaps |
1.3.6.1.2.1.37.2.6 |
Encapsulation |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
vcBridged8023(2), llcEncaps(7) |
|
atmPortConfig |
1.3.6.1.2.1.37.2.7 |
this carry out the actual SET of the logical port.
0 deletes the existing port,
1 creates a new logical port |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..1 |
|
ds3NoSignalCntr |
1.3.6.1.2.1.37.3.1 |
NoSignalCntr stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3NoDS3FrameCntr |
1.3.6.1.2.1.37.3.2 |
NoDS3FrameCntr stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3AISDetectCntr |
1.3.6.1.2.1.37.3.3 |
AISDetectCntr stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3YellowAlarmCntr |
1.3.6.1.2.1.37.3.4 |
YellowAlarmCntr stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3FErrCntr |
1.3.6.1.2.1.37.3.5 |
FErrCntr stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3PErrCntr |
1.3.6.1.2.1.37.3.6 |
PErrCntr stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3CPErrCntr |
1.3.6.1.2.1.37.3.7 |
CPErrCntr stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3FEBlockErrCntr |
1.3.6.1.2.1.37.3.8 |
FEBlockErrCntr stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3BPVErrCntr |
1.3.6.1.2.1.37.3.9 |
BPVErrCntr stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3ATMOCD |
1.3.6.1.2.1.37.3.10 |
ATMOCD stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3FIFOOverflow |
1.3.6.1.2.1.37.3.11 |
FIFOOverflow stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3RAI |
1.3.6.1.2.1.37.3.12 |
RAI stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3RAICntr |
1.3.6.1.2.1.37.3.13 |
RAICntr stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3SignalLoss |
1.3.6.1.2.1.37.3.14 |
SignalLoss stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3FrameLoss |
1.3.6.1.2.1.37.3.15 |
FrameLoss stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3SyncLoss |
1.3.6.1.2.1.37.3.16 |
SyncLoss stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3YellowAlarm |
1.3.6.1.2.1.37.3.17 |
YellowAlarm stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3AISDetect |
1.3.6.1.2.1.37.3.18 |
AISDetect stat |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3ClearErrorCntr |
1.3.6.1.2.1.37.3.19 |
SET this object will clear the Error Counters. |
Status: mandatory |
Access: write-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
set(1) |
|
ds3GFCInsertion |
1.3.6.1.2.1.37.3.20 |
Insertion of GFC bits |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3BipolarSerialIO |
1.3.6.1.2.1.37.3.21 |
Bipolar serial IO |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3PayloadScrambling |
1.3.6.1.2.1.37.3.22 |
Payload scrambling |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3PLCPOverheadProc |
1.3.6.1.2.1.37.3.23 |
PLCP overhead processing |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3FEBEGeneration |
1.3.6.1.2.1.37.3.24 |
FEBE error generation |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3LoopBack |
1.3.6.1.2.1.37.3.25 |
LoopBack Mode |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3FEACGenNDetect |
1.3.6.1.2.1.37.3.26 |
FEAC generation/detection |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3RcvEQ |
1.3.6.1.2.1.37.3.27 |
Use internal receive equalizer |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ds3XmitLevel |
1.3.6.1.2.1.37.3.28 |
transmit level: use normal (low) or long (high) cables |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ssBaseModule |
1.3.6.1.4.1.72.20.1.1 |
Identifies the type of main board card type |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ssIO1Module |
1.3.6.1.4.1.72.20.1.2 |
I/O 1 card type |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
vacant(1), pcnet-6-card-id(2), feast-card-id(3), stakBus-card-id(4), atm-card-id(5) |
|
ssIO2Module |
1.3.6.1.4.1.72.20.1.3 |
I/O 2 card type |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
vacant(1), pcnet-6-card-id(2), feast-card-id(3), stakBus-card-id(4), atm-card-id(5) |
|
ssBaseBootFWVer |
1.3.6.1.4.1.72.20.2.1 |
Version number of current boot firmware |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ssBaseSoftVer |
1.3.6.1.4.1.72.20.2.2 |
Version number of current software |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ssErrorLog |
1.3.6.1.4.1.72.20.2.3 |
A stored value indicating that the unit has
experienced a fault. Log information is formatted
as a four digit hex number. Set to zero to clear
the logged fault. Record this value and call Retix
technical support. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ssStkBusIOPort |
1.3.6.1.4.1.72.20.3.1 |
which I/O port is StakBus installed.
(only 1 stakbus per system is allowed) |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
on-IO1(1), on-IO2(2), not-installed(3) |
|
ssStkBusSpeed |
1.3.6.1.4.1.72.20.3.2 |
StakBus speed. 175000000, or 0 if no StakBus card
installed |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ssStkBusNodeAddr |
1.3.6.1.4.1.72.20.3.3 |
Module ID for StakBus card |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..15 |
|
ssStkBusRingOp |
1.3.6.1.4.1.72.20.3.4 |
StakBus Ring OperationalStatus |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
ringOperational(1), ringNotOperational(2), notInstalled(3) |
|
ssVLANEnDisable |
1.3.6.1.4.1.72.20.4.1 |
Globally enable/disable VLAN for the system |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
portVLANTable |
1.3.6.1.4.1.72.20.4.2 |
Table of port based VLAN configurations.
Entries (rows) are added to the table by issuing a
SET command with the EnableAdd value for the
portVLANEntryEdit object. The new row is created
using the instantiations. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
PortVLANEntry |
|
portVLANEntry |
1.3.6.1.4.1.72.20.4.2.1 |
a VLAN entry containing portID, VLANID, ... |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
PortVLANEntry |
|
|
ssVLANEntryPortID |
1.3.6.1.4.1.72.20.4.2.1.1 |
Port ID |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ssVLANEntryVLANID |
1.3.6.1.4.1.72.20.4.2.1.2 |
Vlan ID |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
ssVLANEntryEdit |
1.3.6.1.4.1.72.20.4.2.1.3 |
When set to enableAdd(1) the instantiations will
be used to create a new table entry (row).
Existing entries can be disabled(2) or deleted (3). |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable-add(1), disable(2), delete(3) |
|
slipEnable |
1.3.6.1.4.1.72.20.5.1 |
enable/disable SLIP |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
slipHostIP |
1.3.6.1.4.1.72.20.5.2 |
SLIP Remote IP Addr |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|