RFC7777-MIB

File: RFC7777-MIB.mib (49271 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB

Imported symbols

IpAddress Counter Gauge
TimeTicks Opaque enterprises
OBJECT-TYPE DisplayString

Defined Types

WfOspfAreaEntry  
SEQUENCE    
  wfOspfAreaDelete INTEGER
  wfOspfAreaDisable INTEGER
  wfOspfAreaState INTEGER
  wfOspfAreaId IpAddress
  wfOspfAuthType INTEGER
  wfOspfImportASExtern INTEGER
  wfOspfStubMetric INTEGER
  wfOspfImportSum INTEGER
  wfOspfSpfCnt Counter

WfOspfLsdbEntry  
SEQUENCE    
  wfOspfLsdbAreaId IpAddress
  wfOspfLsdbType INTEGER
  wfOspfLsdbLSID IpAddress
  wfOspfLsdbRouterId IpAddress
  wfOspfLsdbSequence INTEGER
  wfOspfLsdbAge INTEGER
  wfOspfLsdbChecksum INTEGER
  wfOspfLsdbAdvLen INTEGER

WfOspfAreaRangeEntry  
SEQUENCE    
  wfOspfAreaRangeDelete INTEGER
  wfOspfAreaRangeDisable INTEGER
  wfOspfAreaRangeState INTEGER
  wfOspfAreaRangeAreaID IpAddress
  wfOspfAreaRangeNet IpAddress
  wfOspfAreaRangeMask IpAddress

WfOspfIfEntry  
SEQUENCE    
  wfOspfIfDelete INTEGER
  wfOspfIfDisable INTEGER
  wfOspfIfState INTEGER
  wfOspfIfIpAddress IpAddress
  wfOspfAddressLessIf INTEGER
  wfOspfIfAreaId IpAddress
  wfOspfIfType INTEGER
  wfOspfIfRtrPriority INTEGER
  wfOspfIfTransitDelay INTEGER
  wfOspfIfRetransInterval INTEGER
  wfOspfIfHelloInterval INTEGER
  wfOspfIfRtrDeadInterval INTEGER
  wfOspfIfPollInterval INTEGER
  wfOspfIfDesignatedRouter IpAddress
  wfOspfIfBackupDesignatedRouter IpAddress
  wfOspfIfMetricCost INTEGER
  wfOspfIfAuthKey OCTET STRING
  wfOspfIfTxHellos Counter
  wfOspfIfTxDBDescripts Counter
  wfOspfIfTxLinkStateReqs Counter
  wfOspfIfTxLinkStateUpds Counter
  wfOspfIfTxLinkStateAcks Counter
  wfOspfIfRxHellos Counter
  wfOspfIfRxDBDescripts Counter
  wfOspfIfRxLinkStateReqs Counter
  wfOspfIfRxLinkStateUpds Counter
  wfOspfIfRxLinkStateAcks Counter
  wfOspfIfDrops Counter
  wfOspfMtuSize INTEGER

WfOspfVirtIfEntry  
SEQUENCE    
  wfOspfVirtIfDelete INTEGER
  wfOspfVirtIfDisable INTEGER
  wfOspfVirtIfState INTEGER
  wfOspfVirtIfAreaID IpAddress
  wfOspfVirtIfNeighbor IpAddress
  wfOspfVirtIfTransitDelay INTEGER
  wfOspfVirtIfRetransInterval INTEGER
  wfOspfVirtIfHelloInterval INTEGER
  wfOspfVirtIfRtrDeadInterval INTEGER
  wfOspfVirtIfAuthKey OCTET STRING
  wfOspfVirtIfTxHellos Counter
  wfOspfVirtIfTxDBDescripts Counter
  wfOspfVirtIfTxLinkStateReqs Counter
  wfOspfVirtIfTxLinkStateUpds Counter
  wfOspfVirtIfTxLinkStateAcks Counter
  wfOspfVirtIfRxHellos Counter
  wfOspfVirtIfRxDBDescripts Counter
  wfOspfVirtIfRxLinkStateReqs Counter
  wfOspfVirtIfRxLinkStateUpds Counter
  wfOspfVirtIfRxLinkStateAcks Counter
  wfOspfVirtIfDrops Counter

WfOspfNbrEntry  
SEQUENCE    
  wfOspfNbrDelete INTEGER
  wfOspfNbrDisable INTEGER
  wfOspfNbrState INTEGER
  wfOspfNbrIpAddr IpAddress
  wfOspfNbrIfAddr IpAddress
  wfOspfNbrAddressLessIndex INTEGER
  wfOspfNbrRtrId IpAddress
  wfOspfNbrOptions INTEGER
  wfOspfNbrPriority INTEGER
  wfOspfNbrEvents Counter
  wfOspfNbrLSRetransQLen Gauge

WfOspfVirtNbrEntry  
SEQUENCE    
  wfOspfVirtNbrArea IpAddress
  wfOspfVirtNbrRtrId IpAddress
  wfOspfVirtNbrIpAddr IpAddress
  wfOspfVirtNbrOptions INTEGER
  wfOspfVirtNbrState INTEGER
  wfOspfVirtNbrEvents Counter
  wfOspfVirtNbrLSRetransQLen Gauge

WfOspfDynNbrEntry  
SEQUENCE    
  wfOspfDynNbrState INTEGER
  wfOspfDynNbrIpAddr IpAddress
  wfOspfDynNbrIfAddr IpAddress
  wfOspfDynNbrAddressLessIndex INTEGER
  wfOspfDynNbrRtrId IpAddress
  wfOspfDynNbrOptions INTEGER
  wfOspfDynNbrPriority INTEGER
  wfOspfDynNbrEvents Counter
  wfOspfDynNbrLSRetransQLen Gauge

Defined Values

wellfleet 1.3.6.1.4.1.18
OBJECT IDENTIFIER    

wfOspfGeneralGroup 1.3.6.1.4.1.18.3.5.3.2.3.1
OBJECT IDENTIFIER    

wfOspfGeneralDelete 1.3.6.1.4.1.18.3.5.3.2.3.1.1
'This value determines whether OSPF is configured'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfOspfGeneralDisable 1.3.6.1.4.1.18.3.5.3.2.3.1.2
'The administrative status of OSPF in the router. The value 'enabled' denotes that the OSPF Process is active on at least one interface; 'disabled' disables it on all interfaces.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfOspfGeneralState 1.3.6.1.4.1.18.3.5.3.2.3.1.3
'The state of OSPF'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfOspfRouterId 1.3.6.1.4.1.18.3.5.3.2.3.1.4
'A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.' REFERENCE 'OSPF Version 2, C.1 Global parameters'
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfOspfVersionNumber 1.3.6.1.4.1.18.3.5.3.2.3.1.5
'The current version number of the OSPF protocol is 2.' REFERENCE 'OSPF Version 2, Title'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfAreaBdrRtrStatus 1.3.6.1.4.1.18.3.5.3.2.3.1.6
'A flag to note whether this router is an area border router.' REFERENCE 'OSPF Version 2, Section 3 Splitting the AS into Areas'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfOspfASBdrRtrStatus 1.3.6.1.4.1.18.3.5.3.2.3.1.7
'A flag to note whether this router is an Autonomous System border router.' REFERENCE 'OSPF Version 2, Section 3.3 Classification of routers'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfOspfTOSSupport 1.3.6.1.4.1.18.3.5.3.2.3.1.8
'The router's support for type-of-service routing.' REFERENCE 'OSPF Version 2, Appendix F.1.2 Optional TOS support'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfOspfSpfHoldDown 1.3.6.1.4.1.18.3.5.3.2.3.1.9
Hold Down Timer for the SPF. The SPF will run at most once per hold down timer value. A value of 0 means no hold down.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER defval(1), maximum(10)  

wfOspfSlotMask 1.3.6.1.4.1.18.3.5.3.2.3.1.10
Slot mask for which slots OSPF is eligible to run on. The MSBit represents slot 1, the next most significant bit represents slot 2, and so on... Slots can be 1-14. Default is all slots on a BCN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER slotmask(4261150720)  

wfOspfAreaTable 1.3.6.1.4.1.18.3.5.3.2.3.2
-- The OSPF Area Data Structure contains information -- regarding the various areas. The interfaces and -- virtual links are configured as part of these areas. -- Area 0.0.0.0, by definition, is the Backbone Area 'Information describing the configured parameters and cumulative statistics of the router's attached areas.' REFERENCE 'OSPF Version 2, Section 6 The Area Data Structure'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfAreaEntry

wfOspfAreaEntry 1.3.6.1.4.1.18.3.5.3.2.3.2.1
'Information describing the configured parameters and cumulative statistics of one of the router's attached areas.'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfAreaEntry  

wfOspfAreaDelete 1.3.6.1.4.1.18.3.5.3.2.3.2.1.1
This value determines if the OSPF router is configured with this area.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfOspfAreaDisable 1.3.6.1.4.1.18.3.5.3.2.3.2.1.2
This value indicates the state of this area on the OSPF router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfOspfAreaState 1.3.6.1.4.1.18.3.5.3.2.3.2.1.3
This value indicates the state of the OSPF Area.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

wfOspfAreaId 1.3.6.1.4.1.18.3.5.3.2.3.2.1.4
'A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfAuthType 1.3.6.1.4.1.18.3.5.3.2.3.2.1.5
'The authentication type specified for an area. Additional authentication types may be assigned locally on a per Area basis.' REFERENCE 'OSPF Version 2, Appendix E Authentication' -- none (0), -- simplePassword (1) -- reserved for future specification (2..255) -- reserved for AS specific values (> 255)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER nopassword(1), simplepassword(2)  

wfOspfImportASExtern 1.3.6.1.4.1.18.3.5.3.2.3.2.1.6
'The area's support for importing AS external link- state advertisements.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfOspfStubMetric 1.3.6.1.4.1.18.3.5.3.2.3.2.1.7
'The metric value applied at the indicated type of service. By default, this equals the least metric at the type of service among the interfaces to other areas.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(16777215)  

wfOspfImportSum 1.3.6.1.4.1.18.3.5.3.2.3.2.1.8
'The area's support for importing Summary advertisements into a stub area. This variable should not be set unless wfOspfImportASExtern is set to FALSE'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfOspfSpfCnt 1.3.6.1.4.1.18.3.5.3.2.3.2.1.9
The number of times the OSPF SPF algorithm has been run for this area.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfLsdbTable 1.3.6.1.4.1.18.3.5.3.2.3.3
-- OSPF Link State Database -- The Link State Database contains the Link State -- Advertisements from throughout the areas that the -- device is attached to. 'The OSPF Process's Links State Database.' REFERENCE 'OSPF Version 2, Section 12 Link State Advertisements'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfLsdbEntry

wfOspfLsdbEntry 1.3.6.1.4.1.18.3.5.3.2.3.3.1
'A single Link State Advertisement.'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfLsdbEntry  

wfOspfLsdbAreaId 1.3.6.1.4.1.18.3.5.3.2.3.3.1.1
'The 32 bit identifier of the Area from which the LSA was received.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfLsdbType 1.3.6.1.4.1.18.3.5.3.2.3.3.1.2
'The type of the link state advertisement. Each link state type has a separate advertisement format.' REFERENCE 'OSPF Version 2, Appendix A.4.1 The Link State Advertisement header' stubLink (0), routerLink (1), networkLink (2), summaryLink (3), asSummaryLink (4), asExternalLink (5)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER routerlink(1), networklink(2), summarylink(3), assummarylink(4), asexternallink(5)  

wfOspfLsdbLSID 1.3.6.1.4.1.18.3.5.3.2.3.3.1.3
'The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.' REFERENCE 'OSPF Version 2, Section 12.1.4 Link State ID'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfLsdbRouterId 1.3.6.1.4.1.18.3.5.3.2.3.3.1.4
'The 32 bit number that uniquely identifies the originating router in the Autonomous System.' REFERENCE 'OSPF Version 2, Appendix C.1 Global parameters'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfLsdbSequence 1.3.6.1.4.1.18.3.5.3.2.3.3.1.5
-- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. 'The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.' REFERENCE 'OSPF Version 2, Section 12.1.6 LS sequence number'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfLsdbAge 1.3.6.1.4.1.18.3.5.3.2.3.3.1.6
'This field is the age of the link state advertisement in seconds.' (OSPF_LSDBMINAGE = 0) REFERENCE 'OSPF Version 2, Section 12.1.1 LS age'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER lsdbmaxage(3600)  

wfOspfLsdbChecksum 1.3.6.1.4.1.18.3.5.3.2.3.3.1.7
'This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.' REFERENCE 'OSPF Version 2, Section 12.1.7 LS checksum'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfLsdbAdvLen 1.3.6.1.4.1.18.3.5.3.2.3.3.1.8
'The length of entire Link State Advertisement, including its header.' REFERENCE 'OSPF Version 2, Section 12 Link State Advertisements'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfAreaRangeTable 1.3.6.1.4.1.18.3.5.3.2.3.4
'A range if IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfAreaRangeEntry

wfOspfAreaRangeEntry 1.3.6.1.4.1.18.3.5.3.2.3.4.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfAreaRangeEntry  

wfOspfAreaRangeDelete 1.3.6.1.4.1.18.3.5.3.2.3.4.1.1
This value determines if an Area Range has been configured for the OSPF router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfOspfAreaRangeDisable 1.3.6.1.4.1.18.3.5.3.2.3.4.1.2
'This variable displays the status of the entry. Setting it to 'DISBALED' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfOspfAreaRangeState 1.3.6.1.4.1.18.3.5.3.2.3.4.1.3
The state of the OSPF Area Range.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

wfOspfAreaRangeAreaID 1.3.6.1.4.1.18.3.5.3.2.3.4.1.4
'The Area the Address Range is to be found within.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfAreaRangeNet 1.3.6.1.4.1.18.3.5.3.2.3.4.1.5
'The IP Address of the Net or Subnet indicated by the range.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfAreaRangeMask 1.3.6.1.4.1.18.3.5.3.2.3.4.1.6
'The Subnet Mask that pertains to the Net or Subnet.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfOspfIfTable 1.3.6.1.4.1.18.3.5.3.2.3.5
-- OSPF Interface Table -- The OSPF Interface Table augments the ifTable with OSPF -- specific information. 'The OSPF Interface Table describes the interfaces from the viewpoint of OSPF.' REFERENCE 'OSPF Version 2, Appendix C.3 Router interface parameters'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfIfEntry

wfOspfIfEntry 1.3.6.1.4.1.18.3.5.3.2.3.5.1
'The OSPF Interface Entry describes one interface from the viewpoint of OSPF.'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfIfEntry  

wfOspfIfDelete 1.3.6.1.4.1.18.3.5.3.2.3.5.1.1
This variable determines in an OSPF Interface has been configured on the router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfOspfIfDisable 1.3.6.1.4.1.18.3.5.3.2.3.5.1.2
'The OSPF interface's administrative status. The value 'enabled' denotes that neighbor relationships may be formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfOspfIfState 1.3.6.1.4.1.18.3.5.3.2.3.5.1.3
'The OSPF Interface State.' down (1), loopback (2), waiting (3), pointToPoint (4), designatedRouter (5), backupDesignatedRouter (6), otherDesignatedRouter (7)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(1), loopback(2), waiting(3), pointtopoint(4), designatedrouter(5), backupdesignatedrouter(6), otherdesignatedrouter(7)  

wfOspfIfIpAddress 1.3.6.1.4.1.18.3.5.3.2.3.5.1.4
'The IP address of this OSPF interface.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfAddressLessIf 1.3.6.1.4.1.18.3.5.3.2.3.5.1.5
'For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfIfAreaId 1.3.6.1.4.1.18.3.5.3.2.3.5.1.6
'A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.' default { '00000000'H } -- 0.0.0.0
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfOspfIfType 1.3.6.1.4.1.18.3.5.3.2.3.5.1.7
'The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broadcast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25, Frame Relay, and similar technologies take the value 'nbma', and links that are definitively point to point take the value 'pointToPoint'.' broadcast (1), nbma (2), pointToPoint (3)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER broadcast(1), nbma(2), pointtopoint(3)  

wfOspfIfRtrPriority 1.3.6.1.4.1.18.3.5.3.2.3.5.1.8
'The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER defval(1), maximum(255)  

wfOspfIfTransitDelay 1.3.6.1.4.1.18.3.5.3.2.3.5.1.9
'The estimated number of seconds it takes to transmit a link- state update packet over this interface.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(3600)  

wfOspfIfRetransInterval 1.3.6.1.4.1.18.3.5.3.2.3.5.1.10
'The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(5), maximum(3600)  

wfOspfIfHelloInterval 1.3.6.1.4.1.18.3.5.3.2.3.5.1.11
'The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(10), maximum(65535)  

wfOspfIfRtrDeadInterval 1.3.6.1.4.1.18.3.5.3.2.3.5.1.12
'The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(40), maximum(2147483647)  

wfOspfIfPollInterval 1.3.6.1.4.1.18.3.5.3.2.3.5.1.13
'The larger time interval, in seconds, between the Hello packets sent to an inactive non-broadcast multi- access neighbor.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(120), maximum(2147483647)  

wfOspfIfDesignatedRouter 1.3.6.1.4.1.18.3.5.3.2.3.5.1.14
'The IP Address of the Designated Router.' default { '00000000'H } -- 0.0.0.0
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfIfBackupDesignatedRouter 1.3.6.1.4.1.18.3.5.3.2.3.5.1.15
'The IP Address of the Backup Designated Router.' default { '00000000'H } -- 0.0.0.0
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfIfMetricCost 1.3.6.1.4.1.18.3.5.3.2.3.5.1.16
'The cost of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed. The value FFFF is distinguished to mean 'no route via this TOS'.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(65535)  

wfOspfIfAuthKey 1.3.6.1.4.1.18.3.5.3.2.3.5.1.17
'The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. When read, ospfIfAuthKey always returns an Octet String of length zero.' default { '0000000000000000'H } -- 0.0.0.0.0.0.0.0 REFERENCE 'OSPF Version 2, Section 9 The Interface Data Structure'
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfOspfIfTxHellos 1.3.6.1.4.1.18.3.5.3.2.3.5.1.18
Number of OSPF Hello packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfTxDBDescripts 1.3.6.1.4.1.18.3.5.3.2.3.5.1.19
Number of OSPF DataBase Description packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfTxLinkStateReqs 1.3.6.1.4.1.18.3.5.3.2.3.5.1.20
Number of OSPF Link State Request packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfTxLinkStateUpds 1.3.6.1.4.1.18.3.5.3.2.3.5.1.21
Number of OSPF Link State Update packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfTxLinkStateAcks 1.3.6.1.4.1.18.3.5.3.2.3.5.1.22
Number of OSPF Link States Acknowledgements transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfRxHellos 1.3.6.1.4.1.18.3.5.3.2.3.5.1.23
Number of OSPF Hello packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfRxDBDescripts 1.3.6.1.4.1.18.3.5.3.2.3.5.1.24
Number of OSPF DataBase Description packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfRxLinkStateReqs 1.3.6.1.4.1.18.3.5.3.2.3.5.1.25
Number of OSPF Link State Requests received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfRxLinkStateUpds 1.3.6.1.4.1.18.3.5.3.2.3.5.1.26
Number of OSPF Link State Updates received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfRxLinkStateAcks 1.3.6.1.4.1.18.3.5.3.2.3.5.1.27
Number of OSPF Link State Acknowledgements received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfDrops 1.3.6.1.4.1.18.3.5.3.2.3.5.1.28
Number of OSPF packets dropped because of invalid information in the packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfMtuSize 1.3.6.1.4.1.18.3.5.3.2.3.5.1.29
Configure MTU size per OSPF inreface
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER defval(1), min(2), maximum(10000)  

wfOspfVirtIfTable 1.3.6.1.4.1.18.3.5.3.2.3.6
-- OSPF Virtual Interface Table -- The Virtual Interface Table describes the virtual -- links that the OSPF Process is configured to -- carry on. 'Information about this router's virtual interfaces.' REFERENCE 'OSPF Version 2, Appendix C.4 Virtual link parameters'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfVirtIfEntry

wfOspfVirtIfEntry 1.3.6.1.4.1.18.3.5.3.2.3.6.1
'Information about a single Virtual Interface.'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfVirtIfEntry  

wfOspfVirtIfDelete 1.3.6.1.4.1.18.3.5.3.2.3.6.1.1
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfOspfVirtIfDisable 1.3.6.1.4.1.18.3.5.3.2.3.6.1.2
'This variable displays the validity or invalidity of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfOspfVirtIfState 1.3.6.1.4.1.18.3.5.3.2.3.6.1.3
'OSPF virtual interface states.' down (1), -- these use the same encoding pointToPoint (4) -- as the ospfIfTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(1), pointtopoint(4)  

wfOspfVirtIfAreaID 1.3.6.1.4.1.18.3.5.3.2.3.6.1.4
'The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfVirtIfNeighbor 1.3.6.1.4.1.18.3.5.3.2.3.6.1.5
'The Router ID of the Virtual Neighbor.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfVirtIfTransitDelay 1.3.6.1.4.1.18.3.5.3.2.3.6.1.6
'The estimated number of seconds it takes to transmit a link- state update packet over this interface.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(3600)  

wfOspfVirtIfRetransInterval 1.3.6.1.4.1.18.3.5.3.2.3.6.1.7
'The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets. This value should be well over the expected round-trip time.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(5), maximum(3600)  

wfOspfVirtIfHelloInterval 1.3.6.1.4.1.18.3.5.3.2.3.6.1.8
'The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(15), maximum(65535)  

wfOspfVirtIfRtrDeadInterval 1.3.6.1.4.1.18.3.5.3.2.3.6.1.9
'The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(60), maximum(2147483647)  

wfOspfVirtIfAuthKey 1.3.6.1.4.1.18.3.5.3.2.3.6.1.10
'If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 octets. When read, ospfVifAuthKey always returns a string of length zero.' REFERENCE 'OSPF Version 2, Section 9 The Interface Data Structure'
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfOspfVirtIfTxHellos 1.3.6.1.4.1.18.3.5.3.2.3.6.1.11
Number of OSPF Hello packets transmitted on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfTxDBDescripts 1.3.6.1.4.1.18.3.5.3.2.3.6.1.12
Number of OSPF DataBase Description packets transmitted on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfTxLinkStateReqs 1.3.6.1.4.1.18.3.5.3.2.3.6.1.13
Number of OSPF Link State Request packets transmitted on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfTxLinkStateUpds 1.3.6.1.4.1.18.3.5.3.2.3.6.1.14
Number of OSPF Link State Update packets transmitted on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfTxLinkStateAcks 1.3.6.1.4.1.18.3.5.3.2.3.6.1.15
Number of OSPF Link State Acknowledgement packets transmitted on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfRxHellos 1.3.6.1.4.1.18.3.5.3.2.3.6.1.16
Number of OSPF Hello packets received on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfRxDBDescripts 1.3.6.1.4.1.18.3.5.3.2.3.6.1.17
Number of OSPF DataBase Description packets received on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfRxLinkStateReqs 1.3.6.1.4.1.18.3.5.3.2.3.6.1.18
Number of OSPF Link State Request packets recieved on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfRxLinkStateUpds 1.3.6.1.4.1.18.3.5.3.2.3.6.1.19
Number of OSPF Link State Update packets received on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfRxLinkStateAcks 1.3.6.1.4.1.18.3.5.3.2.3.6.1.20
Number of OSPF Link State Acknowledgement packets received on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfDrops 1.3.6.1.4.1.18.3.5.3.2.3.6.1.21
Number of OSPF packets dropped on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfNbrTable 1.3.6.1.4.1.18.3.5.3.2.3.7
-- OSPF Neighbor Table -- The OSPF Neighbor Table describes all neighbors in -- the locality of the subject router. 'A table of non-virtual neighbor information.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfNbrEntry

wfOspfNbrEntry 1.3.6.1.4.1.18.3.5.3.2.3.7.1
'The information regarding a single neighbor.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfNbrEntry  

wfOspfNbrDelete 1.3.6.1.4.1.18.3.5.3.2.3.7.1.1
This variable indicates the existence of a static OSPF neighbor.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfOspfNbrDisable 1.3.6.1.4.1.18.3.5.3.2.3.7.1.2
'This variable displays the status of the entry. Setting it to 'DISABLED' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfOspfNbrState 1.3.6.1.4.1.18.3.5.3.2.3.7.1.3
'The State of the relationship with this Neighbor.' REFERENCE 'OSPF Version 2, Section 10.1 Neighbor States' down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoway(4), exchangstart(5), exchange(6), loading(7), full(8)  

wfOspfNbrIpAddr 1.3.6.1.4.1.18.3.5.3.2.3.7.1.4
'The IP address of this neighbor.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfNbrIfAddr 1.3.6.1.4.1.18.3.5.3.2.3.7.1.5
'The Interface IP address for this neighbor.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfOspfNbrAddressLessIndex 1.3.6.1.4.1.18.3.5.3.2.3.7.1.6
' On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB. On row creation, this can be derived from the instance.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfNbrRtrId 1.3.6.1.4.1.18.3.5.3.2.3.7.1.7
'A 32-bit integer (represented as a type IpAddress) uniquely identifying the neighboring router in the Autonomous System.' default { '00000000'H } -- 0.0.0.0
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfNbrOptions 1.3.6.1.4.1.18.3.5.3.2.3.7.1.8
'A Bit Mask corresponding to the neighbor's options field. Bit 0, if set, indicates that the area accepts and operates on external information; if zero, it is a stub area. Bit 1, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric.' REFERENCE 'OSPF Version 2, Section 12.1.2 Options'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfNbrPriority 1.3.6.1.4.1.18.3.5.3.2.3.7.1.9
'The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER defval(1), maximum(255)  

wfOspfNbrEvents 1.3.6.1.4.1.18.3.5.3.2.3.7.1.10
'The number of times this neighbor relationship has changed state, or an error has occurred.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfNbrLSRetransQLen 1.3.6.1.4.1.18.3.5.3.2.3.7.1.11
'The current length of the retransmission queue.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfOspfVirtNbrTable 1.3.6.1.4.1.18.3.5.3.2.3.8
-- WFOSPF Virtual Neighbor Table -- This table describes all virtual neighbors. -- Since Virtual Links are configured in the -- virtual interface table, this table is read-only. 'A table of virtual neighbor information.' REFERENCE 'OSPF Version 2, '
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfVirtNbrEntry

wfOspfVirtNbrEntry 1.3.6.1.4.1.18.3.5.3.2.3.8.1
'Virtual neighbor information.' REFERENCE 'OSPF Version 2, '
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfVirtNbrEntry  

wfOspfVirtNbrArea 1.3.6.1.4.1.18.3.5.3.2.3.8.1.1
'The Transit Area Identifier.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfVirtNbrRtrId 1.3.6.1.4.1.18.3.5.3.2.3.8.1.2
'A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfVirtNbrIpAddr 1.3.6.1.4.1.18.3.5.3.2.3.8.1.3
'The IP address this Virtual Neighbor is using.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfVirtNbrOptions 1.3.6.1.4.1.18.3.5.3.2.3.8.1.4
'A bit map corresponding to the neighbor's options field. Thus, Bit 1, if set, indicates that the neighbor supports Type of Service Routing; if zero, no metrics other than TOS 0 are in use by the neighbor.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfVirtNbrState 1.3.6.1.4.1.18.3.5.3.2.3.8.1.5
'The state of the Virtual Neighbor Relationship.' down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoway(4), exchangstart(5), exchange(6), loading(7), full(8)  

wfOspfVirtNbrEvents 1.3.6.1.4.1.18.3.5.3.2.3.8.1.6
'The number of times this virtual link has changed its state, or an error has occurred.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtNbrLSRetransQLen 1.3.6.1.4.1.18.3.5.3.2.3.8.1.7
'The current length of the retransmission queue.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfOspfDynNbrTable 1.3.6.1.4.1.18.3.5.3.2.3.9
-- OSPF Dynamic Neighbor Table -- The OSPF Dynamic Neighbor Table describes all neighbors in -- the locality of the subject router learned during operation. 'A table of non-virtual neighbor information.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfDynNbrEntry

wfOspfDynNbrEntry 1.3.6.1.4.1.18.3.5.3.2.3.9.1
'The information regarding a single neighbor.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfDynNbrEntry  

wfOspfDynNbrState 1.3.6.1.4.1.18.3.5.3.2.3.9.1.1
'The State of the relationship with this Neighbor.' REFERENCE 'OSPF Version 2, Section 10.1 Neighbor States' down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoway(4), exchangstart(5), exchange(6), loading(7), full(8)  

wfOspfDynNbrIpAddr 1.3.6.1.4.1.18.3.5.3.2.3.9.1.2
'The IP address of this neighbor.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfDynNbrIfAddr 1.3.6.1.4.1.18.3.5.3.2.3.9.1.3
'The Interface IP address for this neighbor.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfDynNbrAddressLessIndex 1.3.6.1.4.1.18.3.5.3.2.3.9.1.4
' On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB. On row creation, this can be derived from the instance.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfDynNbrRtrId 1.3.6.1.4.1.18.3.5.3.2.3.9.1.5
'A 32-bit integer (represented as a type IpAddress) uniquely identifying the neighboring router in the Autonomous System.' default { '00000000'H } -- 0.0.0.0
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfDynNbrOptions 1.3.6.1.4.1.18.3.5.3.2.3.9.1.6
'A Bit Mask corresponding to the neighbor's options field. Bit 0, if set, indicates that the area accepts and operates on external information; if zero, it is a stub area. Bit 1, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric.' REFERENCE 'OSPF Version 2, Section 12.1.2 Options'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfDynNbrPriority 1.3.6.1.4.1.18.3.5.3.2.3.9.1.7
'The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfDynNbrEvents 1.3.6.1.4.1.18.3.5.3.2.3.9.1.8
'The number of times this neighbor relationship has changed state, or an error has occurred.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfDynNbrLSRetransQLen 1.3.6.1.4.1.18.3.5.3.2.3.9.1.9
'The current length of the retransmission queue.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge